All of lore.kernel.org
 help / color / mirror / Atom feed
* [U-Boot] [PATCH v2] ARMV7: OMAP3: Add expansion board detection for Beagle
@ 2010-10-29 20:58 Steve Sakoman
  2010-11-04 18:08 ` Stefano Babic
  0 siblings, 1 reply; 2+ messages in thread
From: Steve Sakoman @ 2010-10-29 20:58 UTC (permalink / raw)
  To: u-boot

Beagle expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents.  It prints
the expansion board name and revision and modifies environment variables
as appropriate. This patch is based on the Overo expansion board code.

Signed-off-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
---

Change for v2:
	Add GPIO 162 pinmux for TCT Trainer board

diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index c5d6679..d9b6f01 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -39,6 +39,27 @@
 #include <asm/mach-types.h>
 #include "beagle.h"
 
+#define TWL4030_I2C_BUS			0
+#define EXPANSION_EEPROM_I2C_BUS	1
+#define EXPANSION_EEPROM_I2C_ADDRESS	0x50
+
+#define TINCANTOOLS_ZIPPY		0x01000100
+#define TINCANTOOLS_ZIPPY2		0x02000100
+#define TINCANTOOLS_TRAINER		0x04000100
+#define TINCANTOOLS_SHOWDOG		0x03000100
+#define KBADC_BEAGLEFPGA		0x01000600
+
+#define BEAGLE_NO_EEPROM		0xffffffff
+
+static struct {
+	unsigned int device_vendor;
+	unsigned char revision;
+	unsigned char content;
+	char fab_revision[8];
+	char env_var[16];
+	char env_setting[64];
+} expansion_config;
+
 /*
  * Routine: board_init
  * Description: Early hardware init.
@@ -95,6 +116,31 @@ int get_board_revision(void)
 }
 
 /*
+ * Routine: get_expansion_id
+ * Description: This function checks for expansion board by checking I2C
+ *		bus 1 for the availability of an AT24C01B serial EEPROM.
+ *		returns the device_vendor field from the EEPROM
+ */
+unsigned int get_expansion_id(void)
+{
+	i2c_set_bus_num(EXPANSION_EEPROM_I2C_BUS);
+
+	/* return BEAGLE_NO_EEPROM if eeprom doesn't respond */
+	if (i2c_probe(EXPANSION_EEPROM_I2C_ADDRESS) == 1) {
+		i2c_set_bus_num(TWL4030_I2C_BUS);
+		return BEAGLE_NO_EEPROM;
+	}
+
+	/* read configuration data */
+	i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 1, (u8 *)&expansion_config,
+		 sizeof(expansion_config));
+
+	i2c_set_bus_num(TWL4030_I2C_BUS);
+
+	return expansion_config.device_vendor;
+}
+
+/*
  * Routine: misc_init_r
  * Description: Configure board specific parts
  */
@@ -141,6 +187,55 @@ int misc_init_r(void)
 		printf("Beagle unknown 0x%02x\n", get_board_revision());
 	}
 
+	switch (get_expansion_id()) {
+	case TINCANTOOLS_ZIPPY:
+		printf("Recognized Tincantools Zippy board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		MUX_TINCANTOOLS_ZIPPY();
+		setenv("buddy", "zippy");
+		break;
+	case TINCANTOOLS_ZIPPY2:
+		printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		MUX_TINCANTOOLS_ZIPPY();
+		setenv("buddy", "zippy2");
+		break;
+	case TINCANTOOLS_TRAINER:
+		printf("Recognized Tincantools Trainer board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		MUX_TINCANTOOLS_ZIPPY();
+		MUX_TINCANTOOLS_TRAINER();
+		setenv("buddy", "trainer");
+		break;
+	case TINCANTOOLS_SHOWDOG:
+		printf("Recognized Tincantools Showdow board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		/* Place holder for DSS2 definition for showdog lcd */
+		setenv("defaultdisplay", "showdoglcd");
+		setenv("buddy", "showdog");
+		break;
+	case KBADC_BEAGLEFPGA:
+		printf("Recognized KBADC Beagle FPGA board\n");
+		MUX_KBADC_BEAGLEFPGA();
+		setenv("buddy", "beaglefpga");
+		break;
+	case BEAGLE_NO_EEPROM:
+		printf("No EEPROM on expansion board\n");
+		setenv("buddy", "none");
+		break;
+	default:
+		printf("Unrecognized expansion board: %x\n",
+			expansion_config.device_vendor);
+		setenv("buddy", "unknown");
+	}
+
+	if (expansion_config.content == 1)
+		setenv(expansion_config.env_var, expansion_config.env_setting);
+
 	twl4030_power_init();
 	twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
 
diff --git a/board/ti/beagle/beagle.h b/board/ti/beagle/beagle.h
index ec0da6d..b22b653 100644
--- a/board/ti/beagle/beagle.h
+++ b/board/ti/beagle/beagle.h
@@ -259,8 +259,8 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
 	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)) /*I2C1_SCL*/\
 	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)) /*I2C1_SDA*/\
-	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M4)) /*GPIO_168*/\
-	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M4)) /*GPIO_183*/\
+	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)) /*I2C2_SCL*/\
+	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)) /*I2C2_SDA*/\
 	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)) /*I2C3_SCL*/\
 	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)) /*I2C3_SDA*/\
 	MUX_VAL(CP(I2C4_SCL),		(IEN  | PTU | EN  | M0)) /*I2C4_SCL*/\
@@ -415,4 +415,46 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(SYS_BOOT5),		(IDIS | PTD | DIS | M3)) /*DSS_DATA22*/\
 	MUX_VAL(CP(SYS_BOOT6),		(IDIS | PTD | DIS | M3)) /*DSS_DATA23*/
 
+#define MUX_TINCANTOOLS_ZIPPY() \
+	MUX_VAL(CP(MMC2_CLK),       (IEN  | PTU | EN  | M0)) /*MMC2_CLK*/\
+	MUX_VAL(CP(MMC2_CMD),       (IEN  | PTU | EN  | M0)) /*MMC2_CMD*/\
+	MUX_VAL(CP(MMC2_DAT0),      (IEN  | PTU | EN  | M0)) /*MMC2_DAT0*/\
+	MUX_VAL(CP(MMC2_DAT1),      (IEN  | PTU | EN  | M0)) /*MMC2_DAT1*/\
+	MUX_VAL(CP(MMC2_DAT2),      (IEN  | PTU | EN  | M0)) /*MMC2_DAT2*/\
+	MUX_VAL(CP(MMC2_DAT3),      (IEN  | PTU | EN  | M0)) /*MMC2_DAT3*/\
+	MUX_VAL(CP(MMC2_DAT4),      (IEN  | PTU | EN  | M1)) /*MMC2_DIR_DAT0*/\
+	MUX_VAL(CP(MMC2_DAT5),      (IEN  | PTU | EN  | M1)) /*MMC2_DIR_DAT1*/\
+	MUX_VAL(CP(MMC2_DAT6),      (IEN  | PTU | EN  | M1)) /*MMC2_DIR_CMD*/\
+	MUX_VAL(CP(MMC2_DAT7),      (IEN  | PTU | EN  | M1)) /*MMC2_CLKIN*/\
+	MUX_VAL(CP(MCBSP1_CLKR),    (IEN  | PTU | EN  | M1)) /*MCSPI4_CLK*/\
+	MUX_VAL(CP(MCBSP1_FSR),     (IEN  | PTU | EN  | M4)) /*GPIO_157*/\
+	MUX_VAL(CP(MCBSP1_DX),      (IEN  | PTD | EN  | M1)) /*MCSPI4_SIMO*/\
+	MUX_VAL(CP(MCBSP1_DR),      (IEN  | PTD | DIS | M1)) /*MCSPI4_SOMI*/\
+	MUX_VAL(CP(MCBSP1_FSX),     (IEN  | PTD | EN  | M1)) /*MCSPI4_CS0*/\
+	MUX_VAL(CP(MCBSP1_CLKX),    (IEN  | PTD | DIS | M4)) /*GPIO_162*/\
+	MUX_VAL(CP(MCBSP3_DX),      (IEN  | PTD | DIS | M4)) /*GPIO_140*/\
+	MUX_VAL(CP(MCBSP3_DR),      (IEN  | PTD | DIS | M4)) /*GPIO_142*/\
+	MUX_VAL(CP(MCBSP3_CLKX),    (IEN  | PTD | DIS | M4)) /*GPIO_141*/
+
+#define MUX_TINCANTOOLS_TRAINER() \
+	MUX_VAL(CP(MMC2_CLK),       (IEN  | PTU | EN  | M4)) /*GPIO_130*/\
+	MUX_VAL(CP(MMC2_CMD),       (IEN  | PTU | EN  | M4)) /*GPIO_131*/\
+	MUX_VAL(CP(MMC2_DAT0),      (IEN  | PTU | EN  | M4)) /*GPIO_132*/\
+	MUX_VAL(CP(MMC2_DAT1),      (IEN  | PTU | EN  | M4)) /*GPIO_133*/\
+	MUX_VAL(CP(MMC2_DAT2),      (IEN  | PTU | EN  | M4)) /*GPIO_134*/\
+	MUX_VAL(CP(MMC2_DAT3),      (IEN  | PTU | EN  | M4)) /*GPIO_135*/\
+	MUX_VAL(CP(MMC2_DAT4),      (IEN  | PTU | EN  | M4)) /*GPIO_136*/\
+	MUX_VAL(CP(MMC2_DAT5),      (IEN  | PTU | EN  | M4)) /*GPIO_137*/\
+	MUX_VAL(CP(MMC2_DAT6),      (IEN  | PTU | EN  | M4)) /*GPIO_138*/\
+	MUX_VAL(CP(MMC2_DAT7),      (IEN  | PTU | EN  | M4)) /*GPIO_139*/\
+	MUX_VAL(CP(MCBSP3_DX),      (IEN  | PTU | EN  | M4)) /*GPIO_140*/\
+	MUX_VAL(CP(MCBSP3_CLKX),    (IEN  | PTU | EN  | M4)) /*GPIO_141*/\
+	MUX_VAL(CP(MCBSP1_CLKX),    (IEN  | PTU | EN  | M4)) /*GPIO_162*/
+
+#define MUX_KBADC_BEAGLEFPGA() \
+	MUX_VAL(CP(MCBSP1_CLKR),    (IEN  | PTU | DIS | M1)) /*MCSPI4_CLK*/\
+	MUX_VAL(CP(MCBSP1_DX),      (IDIS | PTU | DIS | M1)) /*MCSPI4_SIMO*/\
+	MUX_VAL(CP(MCBSP1_DR),      (IEN  | PTU | EN  | M1)) /*MCSPI4_SOMI*/\
+	MUX_VAL(CP(MCBSP1_FSX),     (IDIS | PTU | DIS | M1)) /*MCSPI4_CS0*/
+
 #endif
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 1c9a007..e7d5bd0 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -152,6 +152,7 @@
 #define CONFIG_SYS_I2C_SLAVE		1
 #define CONFIG_SYS_I2C_BUS		0
 #define CONFIG_SYS_I2C_BUS_SELECT	1
+#define CONFIG_I2C_MULTI_BUS		1
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 
 /*

^ permalink raw reply related	[flat|nested] 2+ messages in thread
* [U-Boot] [PATCH v2] ARMV7: OMAP3: Add expansion board detection for Beagle
  2010-10-29 20:58 [U-Boot] [PATCH v2] ARMV7: OMAP3: Add expansion board detection for Beagle Steve Sakoman
@ 2010-11-04 18:08 ` Stefano Babic
  0 siblings, 0 replies; 2+ messages in thread
From: Stefano Babic @ 2010-11-04 18:08 UTC (permalink / raw)
  To: u-boot

On 10/29/2010 10:58 PM, Steve Sakoman wrote:
> Beagle expansion boards contain an i2c eeprom to identify themselves.
> This patch adds code to read and parse the eeprom contents.  It prints
> the expansion board name and revision and modifies environment variables
> as appropriate. This patch is based on the Overo expansion board code.
> 
> Signed-off-by: Koen Kooi <k-kooi@ti.com>
> Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
> ---

Tested on beagle rev. C2 + Tincantools Zippy.

Tested-by: Stefano Babic <sbabic@denx.de>

Regards,
Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

^ permalink raw reply	[flat|nested] 2+ messages in thread
end of thread, other threads:[~2010-11-04 18:08 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-10-29 20:58 [U-Boot] [PATCH v2] ARMV7: OMAP3: Add expansion board detection for Beagle Steve Sakoman
2010-11-04 18:08 ` Stefano Babic

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.