* [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
@ 2010-10-29 1:19 Paul Gortmaker
2010-10-29 1:19 ` [PATCH 01/15] net: introduce legacy dir to absorb 10Mbit, ISA, EISA drivers Paul Gortmaker
` (16 more replies)
0 siblings, 17 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
The drivers/net dir has a lot of files - originally there were
no subdirs, but at least now subdirs are being used effectively.
But the original drivers from 10+ years ago are still right
there at the top. This series creates a drivers/net/legacy dir.
The initial target is things like ISA/EISA/MCA drivers, and with
that alone, we can get close to 90 files out of drivers/net.
Plus, by having a semi-defined description for legacy as being
"drivers more than 10 years old" we'll always have a destination
for drivers as they fall out of maintainership and use.
If in fact this series gets agreement, I'm figuring it makes sense
to have it go in either at the beginning of a dev cycle, or at
the very end -- I have no strict preference; whatever is easier
for people on the whole. Since I don't expect a lot of activity
in any of these drivers, hopefully it doesn't impact any one else's
pending changes too significantly either way.
All the moves are 100% translation; I didn't add or change any of
the driver sources at all, so I've used "-M" to format the patches
for e-mail. Similarly, if you apply them and git am nags about
whitespace, that comes directly from the original files.
Paul.
-----
The following changes since commit 19449bfc10d163f0024dd5ae5808e28cda32e7b4:
stmmac: enable/disable rx/tx in the core with a single write. (2010-10-28 11:47:54 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/net-2.6.git legacy-netdev
Paul Gortmaker (15):
net: introduce legacy dir to absorb 10Mbit, ISA, EISA drivers
3c501: relocate ancient 8 bit ISA driver to legacy dir
de6xx: relocate ancient parallel port eth drivers to legacy
sun3: Relocate the sun3 specific lance/83596 drivers to legacy
dec netdev: relocate DIGITAL based drivers to legacy
netdev: relocate i8258x and i8259x based drivers to legacy
lance: relocate legacy 7990 based drivers to legacy
netdev: relocate toplevel 8390 based drivers to legacy dir
netdev: relocate remaining ISA 3Com cards to legacy dir
netdev: relocate more one-off drivers to the legacy dir
netdev: kill off the concept of NET_VENDOR_FOO
netdev: relocate sb1000 ISA cable modem driver to legacy
netdev: kill off NET_ISA Kconfig option
MAINTAINERS: updates for new drivers/net/legacy dir
netdev: relocate LICENSE.SRC to legacy
MAINTAINERS | 19 +-
drivers/net/Kconfig | 747 +-------------------------------
drivers/net/Makefile | 63 +---
drivers/net/arm/etherh.c | 2 +-
drivers/net/{ => legacy}/3c501.c | 0
drivers/net/{ => legacy}/3c501.h | 0
drivers/net/{ => legacy}/3c503.c | 0
drivers/net/{ => legacy}/3c503.h | 0
drivers/net/{ => legacy}/3c505.c | 0
drivers/net/{ => legacy}/3c505.h | 0
drivers/net/{ => legacy}/3c507.c | 0
drivers/net/{ => legacy}/3c509.c | 0
drivers/net/{ => legacy}/3c515.c | 0
drivers/net/{ => legacy}/3c523.c | 0
drivers/net/{ => legacy}/3c523.h | 0
drivers/net/{ => legacy}/3c527.c | 0
drivers/net/{ => legacy}/3c527.h | 0
drivers/net/{ => legacy}/7990.c | 0
drivers/net/{ => legacy}/7990.h | 0
drivers/net/{ => legacy}/82596.c | 0
drivers/net/{ => legacy}/8390.c | 0
drivers/net/{ => legacy}/8390.h | 0
drivers/net/{ => legacy}/8390p.c | 0
drivers/net/legacy/Kconfig | 675 +++++++++++++++++++++++++++++
drivers/net/{ => legacy}/LICENSE.SRC | 0
drivers/net/legacy/Makefile | 78 ++++
drivers/net/{ => legacy}/ac3200.c | 0
drivers/net/{ => legacy}/apne.c | 0
drivers/net/{ => legacy}/ariadne.c | 0
drivers/net/{ => legacy}/ariadne.h | 0
drivers/net/{ => legacy}/at1700.c | 0
drivers/net/{ => legacy}/atarilance.c | 0
drivers/net/{ => legacy}/ax88796.c | 0
drivers/net/{ => legacy}/de600.c | 0
drivers/net/{ => legacy}/de600.h | 0
drivers/net/{ => legacy}/de620.c | 0
drivers/net/{ => legacy}/de620.h | 0
drivers/net/{ => legacy}/declance.c | 0
drivers/net/{ => legacy}/defxx.c | 0
drivers/net/{ => legacy}/defxx.h | 0
drivers/net/{ => legacy}/depca.c | 0
drivers/net/{ => legacy}/depca.h | 0
drivers/net/{ => legacy}/e2100.c | 0
drivers/net/{ => legacy}/eepro.c | 0
drivers/net/{ => legacy}/eexpress.c | 0
drivers/net/{ => legacy}/eexpress.h | 0
drivers/net/{ => legacy}/es3210.c | 0
drivers/net/{ => legacy}/eth16i.c | 0
drivers/net/{ => legacy}/ewrk3.c | 0
drivers/net/{ => legacy}/ewrk3.h | 0
drivers/net/{ => legacy}/hp-plus.c | 0
drivers/net/{ => legacy}/hp.c | 0
drivers/net/{ => legacy}/hplance.c | 0
drivers/net/{ => legacy}/hplance.h | 0
drivers/net/{ => legacy}/hydra.c | 0
drivers/net/{ => legacy}/ibmlana.c | 0
drivers/net/{ => legacy}/ibmlana.h | 0
drivers/net/{ => legacy}/lance.c | 0
drivers/net/{ => legacy}/lasi_82596.c | 0
drivers/net/{ => legacy}/lib82596.c | 0
drivers/net/{ => legacy}/lib8390.c | 0
drivers/net/{ => legacy}/lne390.c | 0
drivers/net/{ => legacy}/lp486e.c | 0
drivers/net/{ => legacy}/mac8390.c | 0
drivers/net/{ => legacy}/mvme147.c | 0
drivers/net/{ => legacy}/ne-h8300.c | 0
drivers/net/{ => legacy}/ne.c | 0
drivers/net/{ => legacy}/ne2.c | 0
drivers/net/{ => legacy}/ne2k-pci.c | 0
drivers/net/{ => legacy}/ne3210.c | 0
drivers/net/{ => legacy}/ni5010.c | 0
drivers/net/{ => legacy}/ni5010.h | 0
drivers/net/{ => legacy}/ni52.c | 0
drivers/net/{ => legacy}/ni52.h | 0
drivers/net/{ => legacy}/ni65.c | 0
drivers/net/{ => legacy}/ni65.h | 0
drivers/net/{ => legacy}/sb1000.c | 0
drivers/net/{ => legacy}/seeq8005.c | 0
drivers/net/{ => legacy}/seeq8005.h | 0
drivers/net/{ => legacy}/smc-mca.c | 0
drivers/net/{ => legacy}/smc-ultra.c | 0
drivers/net/{ => legacy}/smc-ultra32.c | 0
drivers/net/{ => legacy}/smc9194.c | 0
drivers/net/{ => legacy}/smc9194.h | 0
drivers/net/{ => legacy}/sni_82596.c | 0
drivers/net/{ => legacy}/stnic.c | 0
drivers/net/{ => legacy}/sun3_82586.c | 0
drivers/net/{ => legacy}/sun3_82586.h | 0
drivers/net/{ => legacy}/sun3lance.c | 0
drivers/net/{ => legacy}/wd.c | 0
drivers/net/{ => legacy}/znet.c | 0
drivers/net/{ => legacy}/zorro8390.c | 0
drivers/net/pcmcia/axnet_cs.c | 2 +-
drivers/net/pcmcia/pcnet_cs.c | 2 +-
94 files changed, 782 insertions(+), 806 deletions(-)
rename drivers/net/{ => legacy}/3c501.c (100%)
rename drivers/net/{ => legacy}/3c501.h (100%)
rename drivers/net/{ => legacy}/3c503.c (100%)
rename drivers/net/{ => legacy}/3c503.h (100%)
rename drivers/net/{ => legacy}/3c505.c (100%)
rename drivers/net/{ => legacy}/3c505.h (100%)
rename drivers/net/{ => legacy}/3c507.c (100%)
rename drivers/net/{ => legacy}/3c509.c (100%)
rename drivers/net/{ => legacy}/3c515.c (100%)
rename drivers/net/{ => legacy}/3c523.c (100%)
rename drivers/net/{ => legacy}/3c523.h (100%)
rename drivers/net/{ => legacy}/3c527.c (100%)
rename drivers/net/{ => legacy}/3c527.h (100%)
rename drivers/net/{ => legacy}/7990.c (100%)
rename drivers/net/{ => legacy}/7990.h (100%)
rename drivers/net/{ => legacy}/82596.c (100%)
rename drivers/net/{ => legacy}/8390.c (100%)
rename drivers/net/{ => legacy}/8390.h (100%)
rename drivers/net/{ => legacy}/8390p.c (100%)
create mode 100644 drivers/net/legacy/Kconfig
rename drivers/net/{ => legacy}/LICENSE.SRC (100%)
create mode 100644 drivers/net/legacy/Makefile
rename drivers/net/{ => legacy}/ac3200.c (100%)
rename drivers/net/{ => legacy}/apne.c (100%)
rename drivers/net/{ => legacy}/ariadne.c (100%)
rename drivers/net/{ => legacy}/ariadne.h (100%)
rename drivers/net/{ => legacy}/at1700.c (100%)
rename drivers/net/{ => legacy}/atarilance.c (100%)
rename drivers/net/{ => legacy}/ax88796.c (100%)
rename drivers/net/{ => legacy}/de600.c (100%)
rename drivers/net/{ => legacy}/de600.h (100%)
rename drivers/net/{ => legacy}/de620.c (100%)
rename drivers/net/{ => legacy}/de620.h (100%)
rename drivers/net/{ => legacy}/declance.c (100%)
rename drivers/net/{ => legacy}/defxx.c (100%)
rename drivers/net/{ => legacy}/defxx.h (100%)
rename drivers/net/{ => legacy}/depca.c (100%)
rename drivers/net/{ => legacy}/depca.h (100%)
rename drivers/net/{ => legacy}/e2100.c (100%)
rename drivers/net/{ => legacy}/eepro.c (100%)
rename drivers/net/{ => legacy}/eexpress.c (100%)
rename drivers/net/{ => legacy}/eexpress.h (100%)
rename drivers/net/{ => legacy}/es3210.c (100%)
rename drivers/net/{ => legacy}/eth16i.c (100%)
rename drivers/net/{ => legacy}/ewrk3.c (100%)
rename drivers/net/{ => legacy}/ewrk3.h (100%)
rename drivers/net/{ => legacy}/hp-plus.c (100%)
rename drivers/net/{ => legacy}/hp.c (100%)
rename drivers/net/{ => legacy}/hplance.c (100%)
rename drivers/net/{ => legacy}/hplance.h (100%)
rename drivers/net/{ => legacy}/hydra.c (100%)
rename drivers/net/{ => legacy}/ibmlana.c (100%)
rename drivers/net/{ => legacy}/ibmlana.h (100%)
rename drivers/net/{ => legacy}/lance.c (100%)
rename drivers/net/{ => legacy}/lasi_82596.c (100%)
rename drivers/net/{ => legacy}/lib82596.c (100%)
rename drivers/net/{ => legacy}/lib8390.c (100%)
rename drivers/net/{ => legacy}/lne390.c (100%)
rename drivers/net/{ => legacy}/lp486e.c (100%)
rename drivers/net/{ => legacy}/mac8390.c (100%)
rename drivers/net/{ => legacy}/mvme147.c (100%)
rename drivers/net/{ => legacy}/ne-h8300.c (100%)
rename drivers/net/{ => legacy}/ne.c (100%)
rename drivers/net/{ => legacy}/ne2.c (100%)
rename drivers/net/{ => legacy}/ne2k-pci.c (100%)
rename drivers/net/{ => legacy}/ne3210.c (100%)
rename drivers/net/{ => legacy}/ni5010.c (100%)
rename drivers/net/{ => legacy}/ni5010.h (100%)
rename drivers/net/{ => legacy}/ni52.c (100%)
rename drivers/net/{ => legacy}/ni52.h (100%)
rename drivers/net/{ => legacy}/ni65.c (100%)
rename drivers/net/{ => legacy}/ni65.h (100%)
rename drivers/net/{ => legacy}/sb1000.c (100%)
rename drivers/net/{ => legacy}/seeq8005.c (100%)
rename drivers/net/{ => legacy}/seeq8005.h (100%)
rename drivers/net/{ => legacy}/smc-mca.c (100%)
rename drivers/net/{ => legacy}/smc-ultra.c (100%)
rename drivers/net/{ => legacy}/smc-ultra32.c (100%)
rename drivers/net/{ => legacy}/smc9194.c (100%)
rename drivers/net/{ => legacy}/smc9194.h (100%)
rename drivers/net/{ => legacy}/sni_82596.c (100%)
rename drivers/net/{ => legacy}/stnic.c (100%)
rename drivers/net/{ => legacy}/sun3_82586.c (100%)
rename drivers/net/{ => legacy}/sun3_82586.h (100%)
rename drivers/net/{ => legacy}/sun3lance.c (100%)
rename drivers/net/{ => legacy}/wd.c (100%)
rename drivers/net/{ => legacy}/znet.c (100%)
rename drivers/net/{ => legacy}/zorro8390.c (100%)
^ permalink raw reply [flat|nested] 38+ messages in thread
* [PATCH 01/15] net: introduce legacy dir to absorb 10Mbit, ISA, EISA drivers
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 02/15] 3c501: relocate ancient 8 bit ISA driver to legacy dir Paul Gortmaker
` (15 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
There are lots of drivers that date back to the early 1990's when
Linux was started, and they correspond to hardware and bus
technologies that have largely disappeared from in-use hardware over
10 years ago.
There is no need to have these drivers polluting the namespace
in the top level drivers directory any longer; relocation to a
subdirectory is long overdue. Start by creating this new home
for these drivers so that they can be targeted and relocated.
By leaving the default to include the legacy/Kconfig, we ensure
people who have existing stores of their own .config files will
not have drivers silently dropped from their builds.
Since the legacy drivers have their probe ordering defined in
the Space.c file, we don't have to strictly maintain any link
order in moving things from Makefile to legacy/Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 14 ++++++++++++++
drivers/net/Makefile | 1 +
drivers/net/legacy/Kconfig | 2 ++
drivers/net/legacy/Makefile | 3 +++
4 files changed, 20 insertions(+), 0 deletions(-)
create mode 100644 drivers/net/legacy/Kconfig
create mode 100644 drivers/net/legacy/Makefile
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index f24179d..9515f76 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -28,6 +28,20 @@ menuconfig NETDEVICES
# that for each of the symbols.
if NETDEVICES
+config NETDEVICES_LEGACY
+ default y
+ bool "Legacy 10+ year old drivers (10Mbit, ISA, EISA, MCA etc.)"
+ ---help---
+ There are a lot of drivers that exist for really old network
+ hardware that have long since been out of production, and
+ are not really in active use by anyone with hardware that is
+ less than ten years old. Unless you are trying to use really
+ old hardware, you can say no here.
+
+if NETDEVICES_LEGACY
+source "drivers/net/legacy/Kconfig"
+endif
+
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index b8bf93d..8045271 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -299,3 +299,4 @@ obj-$(CONFIG_CAIF) += caif/
obj-$(CONFIG_OCTEON_MGMT_ETHERNET) += octeon/
obj-$(CONFIG_PCH_GBE) += pch_gbe/
+obj-$(CONFIG_NETDEVICES_LEGACY) += legacy/
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
new file mode 100644
index 0000000..4c23adf
--- /dev/null
+++ b/drivers/net/legacy/Kconfig
@@ -0,0 +1,2 @@
+
+# Legacy drivers for ancient ISA/EISA bus devices and the like.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
new file mode 100644
index 0000000..33fd752
--- /dev/null
+++ b/drivers/net/legacy/Makefile
@@ -0,0 +1,3 @@
+#
+# Makefile for the Linux legacy network device drivers.
+#
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 02/15] 3c501: relocate ancient 8 bit ISA driver to legacy dir
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
2010-10-29 1:19 ` [PATCH 01/15] net: introduce legacy dir to absorb 10Mbit, ISA, EISA drivers Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 03/15] de6xx: relocate ancient parallel port eth drivers to legacy Paul Gortmaker
` (14 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
As the oldest bit of "supported" hardware, this 8 bit relic from
the 1980's gets the dubious honour of being the 1st driver to
be relegated to the dark corners of the legacy dir.
It wasn't really a functional bit of kit back in the early 1990's
so don't be expecting it to work now either. Sure it compiles,
but it is largely a historical artefact.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 14 --------------
drivers/net/Makefile | 1 -
drivers/net/{ => legacy}/3c501.c | 0
drivers/net/{ => legacy}/3c501.h | 0
drivers/net/legacy/Kconfig | 14 ++++++++++++++
drivers/net/legacy/Makefile | 2 ++
6 files changed, 16 insertions(+), 15 deletions(-)
rename drivers/net/{ => legacy}/3c501.c (100%)
rename drivers/net/{ => legacy}/3c501.h (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 9515f76..cb7f3f4 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -641,20 +641,6 @@ config NET_VENDOR_3COM
the questions about 3COM cards. If you say Y, you will be asked for
your specific card in the following questions.
-config EL1
- tristate "3c501 \"EtherLink\" support"
- depends on NET_VENDOR_3COM && ISA
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Also, consider buying a
- new card, since the 3c501 is slow, broken, and obsolete: you will
- have problems. Some people suggest to ping ("man ping") a nearby
- machine every minute ("man cron") when using this card.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c501.
-
config EL2
tristate "3c503 \"EtherLink II\" support"
depends on NET_VENDOR_3COM && ISA
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 8045271..eb99117 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -183,7 +183,6 @@ obj-$(CONFIG_DEFXX) += defxx.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
-obj-$(CONFIG_EL1) += 3c501.o
obj-$(CONFIG_EL16) += 3c507.o
obj-$(CONFIG_ELMC) += 3c523.o
obj-$(CONFIG_IBMLANA) += ibmlana.o
diff --git a/drivers/net/3c501.c b/drivers/net/legacy/3c501.c
similarity index 100%
rename from drivers/net/3c501.c
rename to drivers/net/legacy/3c501.c
diff --git a/drivers/net/3c501.h b/drivers/net/legacy/3c501.h
similarity index 100%
rename from drivers/net/3c501.h
rename to drivers/net/legacy/3c501.h
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index 4c23adf..fa2d6f8 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -1,2 +1,16 @@
# Legacy drivers for ancient ISA/EISA bus devices and the like.
+
+config EL1
+ tristate "3c501 \"EtherLink\" support"
+ depends on NET_VENDOR_3COM && ISA
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>. Also, consider buying a
+ new card, since the 3c501 is slow, broken, and obsolete: you will
+ have problems. Some people suggest to ping ("man ping") a nearby
+ machine every minute ("man cron") when using this card.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c501.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index 33fd752..acbf0b2 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -1,3 +1,5 @@
#
# Makefile for the Linux legacy network device drivers.
#
+
+obj-$(CONFIG_EL1) += 3c501.o
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 03/15] de6xx: relocate ancient parallel port eth drivers to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
2010-10-29 1:19 ` [PATCH 01/15] net: introduce legacy dir to absorb 10Mbit, ISA, EISA drivers Paul Gortmaker
2010-10-29 1:19 ` [PATCH 02/15] 3c501: relocate ancient 8 bit ISA driver to legacy dir Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 04/15] sun3: Relocate the sun3 specific lance/83596 " Paul Gortmaker
` (13 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
These old drivers pre-date USB, coming from the early 1990's
and with the legacy parallel port also now largely gone from
any current hardware, these need to be relocated to the legacy
directory, since they won't have been in active use for years.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 30 ------------------------------
drivers/net/Makefile | 2 --
drivers/net/legacy/Kconfig | 30 ++++++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 2 ++
drivers/net/{ => legacy}/de600.c | 0
drivers/net/{ => legacy}/de600.h | 0
drivers/net/{ => legacy}/de620.c | 0
drivers/net/{ => legacy}/de620.h | 0
8 files changed, 32 insertions(+), 32 deletions(-)
rename drivers/net/{ => legacy}/de600.c (100%)
rename drivers/net/{ => legacy}/de600.h (100%)
rename drivers/net/{ => legacy}/de620.c (100%)
rename drivers/net/{ => legacy}/de620.h (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index cb7f3f4..eb65a3a 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1867,36 +1867,6 @@ config ATP
To compile this driver as a module, choose M here: the module
will be called atp.
-config DE600
- tristate "D-Link DE600 pocket adapter support"
- depends on NET_POCKET && PARPORT
- ---help---
- This is a network (Ethernet) device which attaches to your parallel
- port. Read <file:Documentation/networking/DLINK.txt> as well as the
- Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>, if you want to use
- this. It is possible to have several devices share a single parallel
- port and it is safe to compile the corresponding drivers into the
- kernel.
-
- To compile this driver as a module, choose M here: the module
- will be called de600.
-
-config DE620
- tristate "D-Link DE620 pocket adapter support"
- depends on NET_POCKET && PARPORT
- ---help---
- This is a network (Ethernet) device which attaches to your parallel
- port. Read <file:Documentation/networking/DLINK.txt> as well as the
- Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>, if you want to use
- this. It is possible to have several devices share a single parallel
- port and it is safe to compile the corresponding drivers into the
- kernel.
-
- To compile this driver as a module, choose M here: the module
- will be called de620.
-
config SGISEEQ
tristate "SGI Seeq ethernet controller support"
depends on SGI_HAS_SEEQ
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index eb99117..41594da 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -174,8 +174,6 @@ obj-$(CONFIG_DUMMY) += dummy.o
obj-$(CONFIG_IFB) += ifb.o
obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
-obj-$(CONFIG_DE600) += de600.o
-obj-$(CONFIG_DE620) += de620.o
obj-$(CONFIG_LANCE) += lance.o
obj-$(CONFIG_SUN3_82586) += sun3_82586.o
obj-$(CONFIG_SUN3LANCE) += sun3lance.o
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index fa2d6f8..ef6fa1f 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -14,3 +14,33 @@ config EL1
To compile this driver as a module, choose M here. The module
will be called 3c501.
+
+config DE600
+ tristate "D-Link DE600 pocket adapter support"
+ depends on NET_POCKET && PARPORT
+ ---help---
+ This is a network (Ethernet) device which attaches to your parallel
+ port. Read <file:Documentation/networking/DLINK.txt> as well as the
+ Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>, if you want to use
+ this. It is possible to have several devices share a single parallel
+ port and it is safe to compile the corresponding drivers into the
+ kernel.
+
+ To compile this driver as a module, choose M here: the module
+ will be called de600.
+
+config DE620
+ tristate "D-Link DE620 pocket adapter support"
+ depends on NET_POCKET && PARPORT
+ ---help---
+ This is a network (Ethernet) device which attaches to your parallel
+ port. Read <file:Documentation/networking/DLINK.txt> as well as the
+ Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>, if you want to use
+ this. It is possible to have several devices share a single parallel
+ port and it is safe to compile the corresponding drivers into the
+ kernel.
+
+ To compile this driver as a module, choose M here: the module
+ will be called de620.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index acbf0b2..e82ca16 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -3,3 +3,5 @@
#
obj-$(CONFIG_EL1) += 3c501.o
+obj-$(CONFIG_DE600) += de600.o
+obj-$(CONFIG_DE620) += de620.o
diff --git a/drivers/net/de600.c b/drivers/net/legacy/de600.c
similarity index 100%
rename from drivers/net/de600.c
rename to drivers/net/legacy/de600.c
diff --git a/drivers/net/de600.h b/drivers/net/legacy/de600.h
similarity index 100%
rename from drivers/net/de600.h
rename to drivers/net/legacy/de600.h
diff --git a/drivers/net/de620.c b/drivers/net/legacy/de620.c
similarity index 100%
rename from drivers/net/de620.c
rename to drivers/net/legacy/de620.c
diff --git a/drivers/net/de620.h b/drivers/net/legacy/de620.h
similarity index 100%
rename from drivers/net/de620.h
rename to drivers/net/legacy/de620.h
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 04/15] sun3: Relocate the sun3 specific lance/83596 drivers to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (2 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 03/15] de6xx: relocate ancient parallel port eth drivers to legacy Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 05/15] dec netdev: relocate DIGITAL based " Paul Gortmaker
` (12 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
Relocate these old drivers for really old Sun3 hardware to the
legacy dir.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 22 ----------------------
drivers/net/Makefile | 2 --
drivers/net/legacy/Kconfig | 22 ++++++++++++++++++++++
drivers/net/legacy/Makefile | 3 +++
drivers/net/{ => legacy}/sun3_82586.c | 0
drivers/net/{ => legacy}/sun3_82586.h | 0
drivers/net/{ => legacy}/sun3lance.c | 0
7 files changed, 25 insertions(+), 24 deletions(-)
rename drivers/net/{ => legacy}/sun3_82586.c (100%)
rename drivers/net/{ => legacy}/sun3_82586.h (100%)
rename drivers/net/{ => legacy}/sun3lance.c (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index eb65a3a..511745d 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -435,28 +435,6 @@ config ATARILANCE
on the AMD Lance chipset: RieblCard (with or without battery), or
PAMCard VME (also the version by Rhotron, with different addresses).
-config SUN3LANCE
- tristate "Sun3/Sun3x on-board LANCE support"
- depends on SUN3 || SUN3X
- help
- Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
- featured an AMD Lance 10Mbit Ethernet controller on board; say Y
- here to compile in the Linux driver for this and enable Ethernet.
- General Linux information on the Sun 3 and 3x series (now
- discontinued) is at
- <http://www.angelfire.com/ca2/tech68k/sun3.html>.
-
- If you're not building a kernel for a Sun 3, say N.
-
-config SUN3_82586
- bool "Sun3 on-board Intel 82586 support"
- depends on SUN3
- help
- This driver enables support for the on-board Intel 82586 based
- Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
- that this driver does not support 82586-based adapters on additional
- VME boards.
-
config HPLANCE
bool "HP on-board LANCE support"
depends on DIO
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 41594da..152f8b5 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -175,8 +175,6 @@ obj-$(CONFIG_IFB) += ifb.o
obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_LANCE) += lance.o
-obj-$(CONFIG_SUN3_82586) += sun3_82586.o
-obj-$(CONFIG_SUN3LANCE) += sun3lance.o
obj-$(CONFIG_DEFXX) += defxx.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index ef6fa1f..1af0740 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -44,3 +44,25 @@ config DE620
To compile this driver as a module, choose M here: the module
will be called de620.
+
+config SUN3LANCE
+ tristate "Sun3/Sun3x on-board LANCE support"
+ depends on SUN3 || SUN3X
+ help
+ Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
+ featured an AMD Lance 10Mbit Ethernet controller on board; say Y
+ here to compile in the Linux driver for this and enable Ethernet.
+ General Linux information on the Sun 3 and 3x series (now
+ discontinued) is at
+ <http://www.angelfire.com/ca2/tech68k/sun3.html>.
+
+ If you're not building a kernel for a Sun 3, say N.
+
+config SUN3_82586
+ bool "Sun3 on-board Intel 82586 support"
+ depends on SUN3
+ help
+ This driver enables support for the on-board Intel 82586 based
+ Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
+ that this driver does not support 82586-based adapters on additional
+ VME boards.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index e82ca16..f552c77 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -5,3 +5,6 @@
obj-$(CONFIG_EL1) += 3c501.o
obj-$(CONFIG_DE600) += de600.o
obj-$(CONFIG_DE620) += de620.o
+
+obj-$(CONFIG_SUN3_82586) += sun3_82586.o
+obj-$(CONFIG_SUN3LANCE) += sun3lance.o
diff --git a/drivers/net/sun3_82586.c b/drivers/net/legacy/sun3_82586.c
similarity index 100%
rename from drivers/net/sun3_82586.c
rename to drivers/net/legacy/sun3_82586.c
diff --git a/drivers/net/sun3_82586.h b/drivers/net/legacy/sun3_82586.h
similarity index 100%
rename from drivers/net/sun3_82586.h
rename to drivers/net/legacy/sun3_82586.h
diff --git a/drivers/net/sun3lance.c b/drivers/net/legacy/sun3lance.c
similarity index 100%
rename from drivers/net/sun3lance.c
rename to drivers/net/legacy/sun3lance.c
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (3 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 04/15] sun3: Relocate the sun3 specific lance/83596 " Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 4:21 ` Maciej W. Rozycki
2010-10-29 1:19 ` [PATCH 06/15] netdev: relocate i8258x and i8259x " Paul Gortmaker
` (11 subsequent siblings)
16 siblings, 1 reply; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
DEC as a name brand has been gone for over 10 years, and these
drivers represent technology from the 1990's like the venerable
ISA bus. Hence relocate them to the legacy dir.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 63 -----------------------------------
drivers/net/Makefile | 4 --
drivers/net/legacy/Kconfig | 63 +++++++++++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 5 +++
drivers/net/{ => legacy}/declance.c | 0
drivers/net/{ => legacy}/defxx.c | 0
drivers/net/{ => legacy}/defxx.h | 0
drivers/net/{ => legacy}/depca.c | 0
drivers/net/{ => legacy}/depca.h | 0
drivers/net/{ => legacy}/ewrk3.c | 0
drivers/net/{ => legacy}/ewrk3.h | 0
11 files changed, 68 insertions(+), 67 deletions(-)
rename drivers/net/{ => legacy}/declance.c (100%)
rename drivers/net/{ => legacy}/defxx.c (100%)
rename drivers/net/{ => legacy}/defxx.h (100%)
rename drivers/net/{ => legacy}/depca.c (100%)
rename drivers/net/{ => legacy}/depca.h (100%)
rename drivers/net/{ => legacy}/ewrk3.c (100%)
rename drivers/net/{ => legacy}/ewrk3.h (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 511745d..fb58ea7 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1104,19 +1104,6 @@ config AT1700
To compile this driver as a module, choose M here. The module
will be called at1700.
-config DEPCA
- tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
- depends on ISA || EISA || MCA
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto> as well as
- <file:drivers/net/depca.c>.
-
- To compile this driver as a module, choose M here. The module
- will be called depca.
-
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
depends on ISA || EISA || PCI
@@ -1157,20 +1144,6 @@ config E2100
To compile this driver as a module, choose M here. The module
will be called e2100.
-config EWRK3
- tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
- depends on NET_ISA
- select CRC32
- ---help---
- This driver supports the DE203, DE204 and DE205 network (Ethernet)
- cards. If this is for you, say Y and read
- <file:Documentation/networking/ewrk3.txt> in the kernel source as
- well as the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ewrk3.
-
config EEXPRESS
tristate "EtherExpress 16 support"
depends on NET_ISA
@@ -1852,15 +1825,6 @@ config SGISEEQ
Say Y here if you have an Seeq based Ethernet network card. This is
used in many Silicon Graphics machines.
-config DECLANCE
- tristate "DEC LANCE ethernet controller support"
- depends on MACH_DECSTATION
- select CRC32
- help
- This driver is for the series of Ethernet controllers produced by
- DEC (now Compaq) based on the AMD Lance chipset, including the
- DEPCA series. (This chipset is better known via the NE2100 cards.)
-
config 68360_ENET
bool "Motorola 68360 ethernet controller"
depends on M68360
@@ -2913,33 +2877,6 @@ config FDDI
then also Y to the driver for your FDDI card, below). Most people
will say N.
-config DEFXX
- tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
- depends on FDDI && (PCI || EISA || TC)
- ---help---
- This is support for the DIGITAL series of TURBOchannel (DEFTA),
- EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
- to a local FDDI network.
-
- To compile this driver as a module, choose M here: the module
- will be called defxx. If unsure, say N.
-
-config DEFXX_MMIO
- bool
- prompt "Use MMIO instead of PIO" if PCI || EISA
- depends on DEFXX
- default n if PCI || EISA
- default y
- ---help---
- This instructs the driver to use EISA or PCI memory-mapped I/O
- (MMIO) as appropriate instead of programmed I/O ports (PIO).
- Enabling this gives an improvement in processing time in parts
- of the driver, but it may cause problems with EISA (DEFEA)
- adapters. TURBOchannel does not have the concept of I/O ports,
- so MMIO is always used for these (DEFTA) adapters.
-
- If unsure, say N.
-
config SKFP
tristate "SysKonnect FDDI PCI support"
depends on FDDI && PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 152f8b5..f6536fe 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -175,7 +175,6 @@ obj-$(CONFIG_IFB) += ifb.o
obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_LANCE) += lance.o
-obj-$(CONFIG_DEFXX) += defxx.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
@@ -191,8 +190,6 @@ obj-$(CONFIG_8139CP) += 8139cp.o
obj-$(CONFIG_8139TOO) += 8139too.o
obj-$(CONFIG_ZNET) += znet.o
obj-$(CONFIG_CPMAC) += cpmac.o
-obj-$(CONFIG_DEPCA) += depca.o
-obj-$(CONFIG_EWRK3) += ewrk3.o
obj-$(CONFIG_ATP) += atp.o
obj-$(CONFIG_NI5010) += ni5010.o
obj-$(CONFIG_NI52) += ni52.o
@@ -219,7 +216,6 @@ obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
-obj-$(CONFIG_DECLANCE) += declance.o
obj-$(CONFIG_ATARILANCE) += atarilance.o
obj-$(CONFIG_A2065) += a2065.o
obj-$(CONFIG_HYDRA) += hydra.o 8390.o
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index 1af0740..ac163cc 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -66,3 +66,66 @@ config SUN3_82586
Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
that this driver does not support 82586-based adapters on additional
VME boards.
+
+config DEPCA
+ tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
+ depends on ISA || EISA || MCA
+ select CRC32
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto> as well as
+ <file:drivers/net/depca.c>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called depca.
+
+config EWRK3
+ tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
+ depends on NET_ISA
+ select CRC32
+ ---help---
+ This driver supports the DE203, DE204 and DE205 network (Ethernet)
+ cards. If this is for you, say Y and read
+ <file:Documentation/networking/ewrk3.txt> in the kernel source as
+ well as the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ewrk3.
+
+config DECLANCE
+ tristate "DEC LANCE ethernet controller support"
+ depends on MACH_DECSTATION
+ select CRC32
+ help
+ This driver is for the series of Ethernet controllers produced by
+ DEC (now Compaq) based on the AMD Lance chipset, including the
+ DEPCA series. (This chipset is better known via the NE2100 cards.)
+
+config DEFXX
+ tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
+ depends on FDDI && (PCI || EISA || TC)
+ ---help---
+ This is support for the DIGITAL series of TURBOchannel (DEFTA),
+ EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
+ to a local FDDI network.
+
+ To compile this driver as a module, choose M here: the module
+ will be called defxx. If unsure, say N.
+
+config DEFXX_MMIO
+ bool
+ prompt "Use MMIO instead of PIO" if PCI || EISA
+ depends on DEFXX
+ default n if PCI || EISA
+ default y
+ ---help---
+ This instructs the driver to use EISA or PCI memory-mapped I/O
+ (MMIO) as appropriate instead of programmed I/O ports (PIO).
+ Enabling this gives an improvement in processing time in parts
+ of the driver, but it may cause problems with EISA (DEFEA)
+ adapters. TURBOchannel does not have the concept of I/O ports,
+ so MMIO is always used for these (DEFTA) adapters.
+
+ If unsure, say N.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index f552c77..7ab3669 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -8,3 +8,8 @@ obj-$(CONFIG_DE620) += de620.o
obj-$(CONFIG_SUN3_82586) += sun3_82586.o
obj-$(CONFIG_SUN3LANCE) += sun3lance.o
+
+obj-$(CONFIG_DEFXX) += defxx.o
+obj-$(CONFIG_DEPCA) += depca.o
+obj-$(CONFIG_EWRK3) += ewrk3.o
+obj-$(CONFIG_DECLANCE) += declance.o
diff --git a/drivers/net/declance.c b/drivers/net/legacy/declance.c
similarity index 100%
rename from drivers/net/declance.c
rename to drivers/net/legacy/declance.c
diff --git a/drivers/net/defxx.c b/drivers/net/legacy/defxx.c
similarity index 100%
rename from drivers/net/defxx.c
rename to drivers/net/legacy/defxx.c
diff --git a/drivers/net/defxx.h b/drivers/net/legacy/defxx.h
similarity index 100%
rename from drivers/net/defxx.h
rename to drivers/net/legacy/defxx.h
diff --git a/drivers/net/depca.c b/drivers/net/legacy/depca.c
similarity index 100%
rename from drivers/net/depca.c
rename to drivers/net/legacy/depca.c
diff --git a/drivers/net/depca.h b/drivers/net/legacy/depca.h
similarity index 100%
rename from drivers/net/depca.h
rename to drivers/net/legacy/depca.h
diff --git a/drivers/net/ewrk3.c b/drivers/net/legacy/ewrk3.c
similarity index 100%
rename from drivers/net/ewrk3.c
rename to drivers/net/legacy/ewrk3.c
diff --git a/drivers/net/ewrk3.h b/drivers/net/legacy/ewrk3.h
similarity index 100%
rename from drivers/net/ewrk3.h
rename to drivers/net/legacy/ewrk3.h
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 06/15] netdev: relocate i8258x and i8259x based drivers to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (4 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 05/15] dec netdev: relocate DIGITAL based " Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 07/15] lance: relocate legacy 7990 " Paul Gortmaker
` (10 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
This chipset was predominately deployed on hardware in the early
to mid 1990's -- on ISA bus hardware and similar. Move these old
drivers to the legacy dir.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 133 ---------------------------------
drivers/net/Makefile | 16 ----
drivers/net/{ => legacy}/3c505.c | 0
drivers/net/{ => legacy}/3c505.h | 0
drivers/net/{ => legacy}/3c507.c | 0
drivers/net/{ => legacy}/3c523.c | 0
drivers/net/{ => legacy}/3c523.h | 0
drivers/net/{ => legacy}/3c527.c | 0
drivers/net/{ => legacy}/3c527.h | 0
drivers/net/{ => legacy}/82596.c | 0
drivers/net/legacy/Kconfig | 133 +++++++++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 17 ++++
drivers/net/{ => legacy}/eepro.c | 0
drivers/net/{ => legacy}/eexpress.c | 0
drivers/net/{ => legacy}/eexpress.h | 0
drivers/net/{ => legacy}/lasi_82596.c | 0
drivers/net/{ => legacy}/lib82596.c | 0
drivers/net/{ => legacy}/lp486e.c | 0
drivers/net/{ => legacy}/ni52.c | 0
drivers/net/{ => legacy}/ni52.h | 0
drivers/net/{ => legacy}/sni_82596.c | 0
drivers/net/{ => legacy}/znet.c | 0
22 files changed, 150 insertions(+), 149 deletions(-)
rename drivers/net/{ => legacy}/3c505.c (100%)
rename drivers/net/{ => legacy}/3c505.h (100%)
rename drivers/net/{ => legacy}/3c507.c (100%)
rename drivers/net/{ => legacy}/3c523.c (100%)
rename drivers/net/{ => legacy}/3c523.h (100%)
rename drivers/net/{ => legacy}/3c527.c (100%)
rename drivers/net/{ => legacy}/3c527.h (100%)
rename drivers/net/{ => legacy}/82596.c (100%)
rename drivers/net/{ => legacy}/eepro.c (100%)
rename drivers/net/{ => legacy}/eexpress.c (100%)
rename drivers/net/{ => legacy}/eexpress.h (100%)
rename drivers/net/{ => legacy}/lasi_82596.c (100%)
rename drivers/net/{ => legacy}/lib82596.c (100%)
rename drivers/net/{ => legacy}/lp486e.c (100%)
rename drivers/net/{ => legacy}/ni52.c (100%)
rename drivers/net/{ => legacy}/ni52.h (100%)
rename drivers/net/{ => legacy}/sni_82596.c (100%)
rename drivers/net/{ => legacy}/znet.c (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index fb58ea7..db8261c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -409,24 +409,6 @@ config MVME147_NET
driver for this chip in your kernel.
To compile this driver as a module, choose M here.
-config MVME16x_NET
- tristate "MVME16x Ethernet support"
- depends on MVME16x
- help
- This is the driver for the Ethernet interface on the Motorola
- MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
- driver for this chip in your kernel.
- To compile this driver as a module, choose M here.
-
-config BVME6000_NET
- tristate "BVME6000 Ethernet support"
- depends on BVME6000
- help
- This is the driver for the Ethernet interface on BVME4000 and
- BVME6000 VME boards. Say Y here to include the driver for this chip
- in your kernel.
- To compile this driver as a module, choose M here.
-
config ATARILANCE
tristate "Atari Lance support"
depends on ATARI
@@ -443,20 +425,6 @@ config HPLANCE
If you want to use the builtin "LANCE" Ethernet controller on an
HP300 machine, say Y here.
-config LASI_82596
- tristate "Lasi ethernet"
- depends on GSC
- help
- Say Y here to support the builtin Intel 82596 ethernet controller
- found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
-
-config SNI_82596
- tristate "SNI RM ethernet"
- depends on NET_ETHERNET && SNI_RM
- help
- Say Y here to support the on-board Intel 82596 ethernet controller
- built into SNI RM machines.
-
config KORINA
tristate "Korina (IDT RC32434) Ethernet support"
depends on NET_ETHERNET && MIKROTIK_RB532
@@ -631,29 +599,6 @@ config EL2
To compile this driver as a module, choose M here. The module
will be called 3c503.
-config ELPLUS
- tristate "3c505 \"EtherLink Plus\" support"
- depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
- ---help---
- Information about this network (Ethernet) card can be found in
- <file:Documentation/networking/3c505.txt>. If you have a card of
- this type, say Y and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c505.
-
-config EL16
- tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
- depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c507.
-
config EL3
tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
@@ -680,28 +625,6 @@ config 3C515
To compile this driver as a module, choose M here. The module
will be called 3c515.
-config ELMC
- tristate "3c523 \"EtherLink/MC\" support"
- depends on NET_VENDOR_3COM && MCA_LEGACY
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c523.
-
-config ELMC_II
- tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
- depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c527.
-
config VORTEX
tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
depends on NET_VENDOR_3COM && (PCI || EISA)
@@ -1057,17 +980,6 @@ config NI5010
To compile this driver as a module, choose M here. The module
will be called ni5010.
-config NI52
- tristate "NI5210 support"
- depends on NET_VENDOR_RACAL && ISA
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ni52.
-
config NI65
tristate "NI6510 support"
depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
@@ -1144,33 +1056,6 @@ config E2100
To compile this driver as a module, choose M here. The module
will be called e2100.
-config EEXPRESS
- tristate "EtherExpress 16 support"
- depends on NET_ISA
- ---help---
- If you have an EtherExpress16 network (Ethernet) card, say Y and
- read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Note that the Intel
- EtherExpress16 card used to be regarded as a very poor choice
- because the driver was very unreliable. We now have a new driver
- that should do better.
-
- To compile this driver as a module, choose M here. The module
- will be called eexpress.
-
-config EEXPRESS_PRO
- tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
- depends on NET_ISA
- ---help---
- If you have a network (Ethernet) card of this type, say Y. This
- driver supports Intel i82595{FX,TX} based boards. Note however
- that the EtherExpress PRO/100 Ethernet card has its own separate
- driver. Please read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called eepro.
-
config HPLAN_PLUS
tristate "HP PCLAN+ (27247B and 27252A) support"
depends on NET_ISA
@@ -1195,14 +1080,6 @@ config HPLAN
To compile this driver as a module, choose M here. The module
will be called hp.
-config LP486E
- tristate "LP486E on board Ethernet"
- depends on NET_ISA
- help
- Say Y here to support the 82596-based on-board Ethernet controller
- for the Panther motherboard, which is one of the two shipped in the
- Intel Professional Workstation.
-
config ETH16I
tristate "ICL EtherTeam 16i/32 support"
depends on NET_ISA
@@ -1234,16 +1111,6 @@ config NE2000
To compile this driver as a module, choose M here. The module
will be called ne.
-config ZNET
- tristate "Zenith Z-Note support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
- help
- The Zenith Z-Note notebook computer has a built-in network
- (Ethernet) card, and this is the Linux driver for it. Note that the
- IBM Thinkpad 300 is compatible with the Z-Note and is also supported
- by this driver. Read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
config SEEQ8005
tristate "SEEQ8005 support (EXPERIMENTAL)"
depends on NET_ISA && EXPERIMENTAL
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index f6536fe..3fd125e 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -178,34 +178,18 @@ obj-$(CONFIG_LANCE) += lance.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
-obj-$(CONFIG_EL16) += 3c507.o
-obj-$(CONFIG_ELMC) += 3c523.o
obj-$(CONFIG_IBMLANA) += ibmlana.o
-obj-$(CONFIG_ELMC_II) += 3c527.o
obj-$(CONFIG_EL3) += 3c509.o
obj-$(CONFIG_3C515) += 3c515.o
-obj-$(CONFIG_EEXPRESS) += eexpress.o
-obj-$(CONFIG_EEXPRESS_PRO) += eepro.o
obj-$(CONFIG_8139CP) += 8139cp.o
obj-$(CONFIG_8139TOO) += 8139too.o
-obj-$(CONFIG_ZNET) += znet.o
obj-$(CONFIG_CPMAC) += cpmac.o
obj-$(CONFIG_ATP) += atp.o
obj-$(CONFIG_NI5010) += ni5010.o
-obj-$(CONFIG_NI52) += ni52.o
obj-$(CONFIG_NI65) += ni65.o
-obj-$(CONFIG_ELPLUS) += 3c505.o
obj-$(CONFIG_AC3200) += ac3200.o 8390.o
-obj-$(CONFIG_APRICOT) += 82596.o
-obj-$(CONFIG_LASI_82596) += lasi_82596.o
-obj-$(CONFIG_SNI_82596) += sni_82596.o
-obj-$(CONFIG_MVME16x_NET) += 82596.o
-obj-$(CONFIG_BVME6000_NET) += 82596.o
obj-$(CONFIG_SC92031) += sc92031.o
-# This is also a 82596 and should probably be merged
-obj-$(CONFIG_LP486E) += lp486e.o
-
obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
diff --git a/drivers/net/3c505.c b/drivers/net/legacy/3c505.c
similarity index 100%
rename from drivers/net/3c505.c
rename to drivers/net/legacy/3c505.c
diff --git a/drivers/net/3c505.h b/drivers/net/legacy/3c505.h
similarity index 100%
rename from drivers/net/3c505.h
rename to drivers/net/legacy/3c505.h
diff --git a/drivers/net/3c507.c b/drivers/net/legacy/3c507.c
similarity index 100%
rename from drivers/net/3c507.c
rename to drivers/net/legacy/3c507.c
diff --git a/drivers/net/3c523.c b/drivers/net/legacy/3c523.c
similarity index 100%
rename from drivers/net/3c523.c
rename to drivers/net/legacy/3c523.c
diff --git a/drivers/net/3c523.h b/drivers/net/legacy/3c523.h
similarity index 100%
rename from drivers/net/3c523.h
rename to drivers/net/legacy/3c523.h
diff --git a/drivers/net/3c527.c b/drivers/net/legacy/3c527.c
similarity index 100%
rename from drivers/net/3c527.c
rename to drivers/net/legacy/3c527.c
diff --git a/drivers/net/3c527.h b/drivers/net/legacy/3c527.h
similarity index 100%
rename from drivers/net/3c527.h
rename to drivers/net/legacy/3c527.h
diff --git a/drivers/net/82596.c b/drivers/net/legacy/82596.c
similarity index 100%
rename from drivers/net/82596.c
rename to drivers/net/legacy/82596.c
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index ac163cc..c84f87c 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -129,3 +129,136 @@ config DEFXX_MMIO
so MMIO is always used for these (DEFTA) adapters.
If unsure, say N.
+
+config MVME16x_NET
+ tristate "MVME16x Ethernet support"
+ depends on MVME16x
+ help
+ This is the driver for the Ethernet interface on the Motorola
+ MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
+ driver for this chip in your kernel.
+ To compile this driver as a module, choose M here.
+
+config BVME6000_NET
+ tristate "BVME6000 Ethernet support"
+ depends on BVME6000
+ help
+ This is the driver for the Ethernet interface on BVME4000 and
+ BVME6000 VME boards. Say Y here to include the driver for this chip
+ in your kernel.
+ To compile this driver as a module, choose M here.
+
+config LASI_82596
+ tristate "Lasi ethernet"
+ depends on GSC
+ help
+ Say Y here to support the builtin Intel 82596 ethernet controller
+ found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
+
+config SNI_82596
+ tristate "SNI RM ethernet"
+ depends on NET_ETHERNET && SNI_RM
+ help
+ Say Y here to support the on-board Intel 82596 ethernet controller
+ built into SNI RM machines.
+
+config ELPLUS
+ tristate "3c505 \"EtherLink Plus\" support"
+ depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
+ ---help---
+ Information about this network (Ethernet) card can be found in
+ <file:Documentation/networking/3c505.txt>. If you have a card of
+ this type, say Y and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c505.
+
+config EL16
+ tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
+ depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c507.
+
+config ELMC
+ tristate "3c523 \"EtherLink/MC\" support"
+ depends on NET_VENDOR_3COM && MCA_LEGACY
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c523.
+
+config ELMC_II
+ tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
+ depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c527.
+
+config EEXPRESS
+ tristate "EtherExpress 16 support"
+ depends on NET_ISA
+ ---help---
+ If you have an EtherExpress16 network (Ethernet) card, say Y and
+ read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>. Note that the Intel
+ EtherExpress16 card used to be regarded as a very poor choice
+ because the driver was very unreliable. We now have a new driver
+ that should do better.
+
+ To compile this driver as a module, choose M here. The module
+ will be called eexpress.
+
+config EEXPRESS_PRO
+ tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
+ depends on NET_ISA
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y. This
+ driver supports Intel i82595{FX,TX} based boards. Note however
+ that the EtherExpress PRO/100 Ethernet card has its own separate
+ driver. Please read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called eepro.
+
+config LP486E
+ tristate "LP486E on board Ethernet"
+ depends on NET_ISA
+ help
+ Say Y here to support the 82596-based on-board Ethernet controller
+ for the Panther motherboard, which is one of the two shipped in the
+ Intel Professional Workstation.
+
+config ZNET
+ tristate "Zenith Z-Note support (EXPERIMENTAL)"
+ depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
+ help
+ The Zenith Z-Note notebook computer has a built-in network
+ (Ethernet) card, and this is the Linux driver for it. Note that the
+ IBM Thinkpad 300 is compatible with the Z-Note and is also supported
+ by this driver. Read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+config NI52
+ tristate "NI5210 support"
+ depends on NET_VENDOR_RACAL && ISA
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ni52.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index 7ab3669..b605648 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -13,3 +13,20 @@ obj-$(CONFIG_DEFXX) += defxx.o
obj-$(CONFIG_DEPCA) += depca.o
obj-$(CONFIG_EWRK3) += ewrk3.o
obj-$(CONFIG_DECLANCE) += declance.o
+
+# 825xx based cards
+obj-$(CONFIG_APRICOT) += 82596.o
+obj-$(CONFIG_BVME6000_NET) += 82596.o
+obj-$(CONFIG_ELPLUS) += 3c505.o
+obj-$(CONFIG_EL16) += 3c507.o
+obj-$(CONFIG_ELMC) += 3c523.o
+obj-$(CONFIG_ELMC_II) += 3c527.o
+obj-$(CONFIG_EEXPRESS) += eexpress.o
+obj-$(CONFIG_EEXPRESS_PRO) += eepro.o
+obj-$(CONFIG_LASI_82596) += lasi_82596.o
+obj-$(CONFIG_LP486E) += lp486e.o
+obj-$(CONFIG_MVME16x_NET) += 82596.o
+obj-$(CONFIG_NI52) += ni52.o
+obj-$(CONFIG_SNI_82596) += sni_82596.o
+obj-$(CONFIG_ZNET) += znet.o
+
diff --git a/drivers/net/eepro.c b/drivers/net/legacy/eepro.c
similarity index 100%
rename from drivers/net/eepro.c
rename to drivers/net/legacy/eepro.c
diff --git a/drivers/net/eexpress.c b/drivers/net/legacy/eexpress.c
similarity index 100%
rename from drivers/net/eexpress.c
rename to drivers/net/legacy/eexpress.c
diff --git a/drivers/net/eexpress.h b/drivers/net/legacy/eexpress.h
similarity index 100%
rename from drivers/net/eexpress.h
rename to drivers/net/legacy/eexpress.h
diff --git a/drivers/net/lasi_82596.c b/drivers/net/legacy/lasi_82596.c
similarity index 100%
rename from drivers/net/lasi_82596.c
rename to drivers/net/legacy/lasi_82596.c
diff --git a/drivers/net/lib82596.c b/drivers/net/legacy/lib82596.c
similarity index 100%
rename from drivers/net/lib82596.c
rename to drivers/net/legacy/lib82596.c
diff --git a/drivers/net/lp486e.c b/drivers/net/legacy/lp486e.c
similarity index 100%
rename from drivers/net/lp486e.c
rename to drivers/net/legacy/lp486e.c
diff --git a/drivers/net/ni52.c b/drivers/net/legacy/ni52.c
similarity index 100%
rename from drivers/net/ni52.c
rename to drivers/net/legacy/ni52.c
diff --git a/drivers/net/ni52.h b/drivers/net/legacy/ni52.h
similarity index 100%
rename from drivers/net/ni52.h
rename to drivers/net/legacy/ni52.h
diff --git a/drivers/net/sni_82596.c b/drivers/net/legacy/sni_82596.c
similarity index 100%
rename from drivers/net/sni_82596.c
rename to drivers/net/legacy/sni_82596.c
diff --git a/drivers/net/znet.c b/drivers/net/legacy/znet.c
similarity index 100%
rename from drivers/net/znet.c
rename to drivers/net/legacy/znet.c
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 07/15] lance: relocate legacy 7990 based drivers to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (5 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 06/15] netdev: relocate i8258x and i8259x " Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 08/15] netdev: relocate toplevel 8390 based drivers to legacy dir Paul Gortmaker
` (9 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
The original ISA 7990 chip was good for its day, given that it
had bus mastering capabilities instead of the PIO or shared memory
modes of the other hardware devices of the day. However it is now
also no longer really relevant and so move the related drivers off
to the legacy directory.
I've left sunlance where it is, since it is still in both sparc
defconfig files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 59 ---------------------------------
drivers/net/Makefile | 6 ---
drivers/net/{ => legacy}/7990.c | 0
drivers/net/{ => legacy}/7990.h | 0
drivers/net/legacy/Kconfig | 59 +++++++++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 7 ++++
drivers/net/{ => legacy}/ariadne.c | 0
drivers/net/{ => legacy}/ariadne.h | 0
drivers/net/{ => legacy}/atarilance.c | 0
drivers/net/{ => legacy}/hplance.c | 0
drivers/net/{ => legacy}/hplance.h | 0
drivers/net/{ => legacy}/lance.c | 0
drivers/net/{ => legacy}/mvme147.c | 0
drivers/net/{ => legacy}/ni65.c | 0
drivers/net/{ => legacy}/ni65.h | 0
15 files changed, 66 insertions(+), 65 deletions(-)
rename drivers/net/{ => legacy}/7990.c (100%)
rename drivers/net/{ => legacy}/7990.h (100%)
rename drivers/net/{ => legacy}/ariadne.c (100%)
rename drivers/net/{ => legacy}/ariadne.h (100%)
rename drivers/net/{ => legacy}/atarilance.c (100%)
rename drivers/net/{ => legacy}/hplance.c (100%)
rename drivers/net/{ => legacy}/hplance.h (100%)
rename drivers/net/{ => legacy}/lance.c (100%)
rename drivers/net/{ => legacy}/mvme147.c (100%)
rename drivers/net/{ => legacy}/ni65.c (100%)
rename drivers/net/{ => legacy}/ni65.h (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index db8261c..6ef5848 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -299,16 +299,6 @@ config BMAC
To compile this driver as a module, choose M here: the module
will be called bmac.
-config ARIADNE
- tristate "Ariadne support"
- depends on ZORRO
- help
- If you have a Village Tronic Ariadne Ethernet adapter, say Y.
- Otherwise, say N.
-
- To compile this driver as a module, choose M here: the module
- will be called ariadne.
-
config A2065
tristate "A2065 support"
depends on ZORRO
@@ -399,32 +389,6 @@ config MACMACE
say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-config MVME147_NET
- tristate "MVME147 (Lance) Ethernet support"
- depends on MVME147
- select CRC32
- help
- Support for the on-board Ethernet interface on the Motorola MVME147
- single-board computer. Say Y here to include the
- driver for this chip in your kernel.
- To compile this driver as a module, choose M here.
-
-config ATARILANCE
- tristate "Atari Lance support"
- depends on ATARI
- help
- Say Y to include support for several Atari Ethernet adapters based
- on the AMD Lance chipset: RieblCard (with or without battery), or
- PAMCard VME (also the version by Rhotron, with different addresses).
-
-config HPLANCE
- bool "HP on-board LANCE support"
- depends on DIO
- select CRC32
- help
- If you want to use the builtin "LANCE" Ethernet controller on an
- HP300 machine, say Y here.
-
config KORINA
tristate "Korina (IDT RC32434) Ethernet support"
depends on NET_ETHERNET && MIKROTIK_RB532
@@ -665,18 +629,6 @@ config TYPHOON
To compile this driver as a module, choose M here. The module
will be called typhoon.
-config LANCE
- tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
- depends on ISA && ISA_DMA_API
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
- of this type.
-
- To compile this driver as a module, choose M here: the module
- will be called lance. This is recommended.
-
config NET_VENDOR_SMC
bool "Western Digital/SMC cards"
depends on ISA || MCA || EISA || MAC
@@ -980,17 +932,6 @@ config NI5010
To compile this driver as a module, choose M here. The module
will be called ni5010.
-config NI65
- tristate "NI6510 support"
- depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ni65.
-
config DNET
tristate "Dave ethernet support (DNET)"
depends on NET_ETHERNET && HAS_IOMEM
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 3fd125e..68c1eb9 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -174,7 +174,6 @@ obj-$(CONFIG_DUMMY) += dummy.o
obj-$(CONFIG_IFB) += ifb.o
obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
-obj-$(CONFIG_LANCE) += lance.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
@@ -186,24 +185,19 @@ obj-$(CONFIG_8139TOO) += 8139too.o
obj-$(CONFIG_CPMAC) += cpmac.o
obj-$(CONFIG_ATP) += atp.o
obj-$(CONFIG_NI5010) += ni5010.o
-obj-$(CONFIG_NI65) += ni65.o
obj-$(CONFIG_AC3200) += ac3200.o 8390.o
obj-$(CONFIG_SC92031) += sc92031.o
obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
-obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
-obj-$(CONFIG_MVME147_NET) += mvme147.o 7990.o
obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
-obj-$(CONFIG_ATARILANCE) += atarilance.o
obj-$(CONFIG_A2065) += a2065.o
obj-$(CONFIG_HYDRA) += hydra.o 8390.o
-obj-$(CONFIG_ARIADNE) += ariadne.o
obj-$(CONFIG_CS89x0) += cs89x0.o
obj-$(CONFIG_MACSONIC) += macsonic.o
obj-$(CONFIG_MACMACE) += macmace.o
diff --git a/drivers/net/7990.c b/drivers/net/legacy/7990.c
similarity index 100%
rename from drivers/net/7990.c
rename to drivers/net/legacy/7990.c
diff --git a/drivers/net/7990.h b/drivers/net/legacy/7990.h
similarity index 100%
rename from drivers/net/7990.h
rename to drivers/net/legacy/7990.h
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index c84f87c..32bd91a 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -262,3 +262,62 @@ config NI52
To compile this driver as a module, choose M here. The module
will be called ni52.
+
+config NI65
+ tristate "NI6510 support"
+ depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ni65.
+
+config MVME147_NET
+ tristate "MVME147 (Lance) Ethernet support"
+ depends on MVME147
+ select CRC32
+ help
+ Support for the on-board Ethernet interface on the Motorola MVME147
+ single-board computer. Say Y here to include the
+ driver for this chip in your kernel.
+ To compile this driver as a module, choose M here.
+
+config ATARILANCE
+ tristate "Atari Lance support"
+ depends on ATARI
+ help
+ Say Y to include support for several Atari Ethernet adapters based
+ on the AMD Lance chipset: RieblCard (with or without battery), or
+ PAMCard VME (also the version by Rhotron, with different addresses).
+
+config ARIADNE
+ tristate "Ariadne support"
+ depends on ZORRO
+ help
+ If you have a Village Tronic Ariadne Ethernet adapter, say Y.
+ Otherwise, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ariadne.
+
+config HPLANCE
+ bool "HP on-board LANCE support"
+ depends on DIO
+ select CRC32
+ help
+ If you want to use the builtin "LANCE" Ethernet controller on an
+ HP300 machine, say Y here.
+
+config LANCE
+ tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
+ depends on ISA && ISA_DMA_API
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
+ of this type.
+
+ To compile this driver as a module, choose M here: the module
+ will be called lance. This is recommended.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index b605648..0eb679c 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -30,3 +30,10 @@ obj-$(CONFIG_NI52) += ni52.o
obj-$(CONFIG_SNI_82596) += sni_82596.o
obj-$(CONFIG_ZNET) += znet.o
+# Lance based cards
+obj-$(CONFIG_ATARILANCE) += atarilance.o
+obj-$(CONFIG_ARIADNE) += ariadne.o
+obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
+obj-$(CONFIG_LANCE) += lance.o
+obj-$(CONFIG_MVME147_NET) += mvme147.o 7990.o
+obj-$(CONFIG_NI65) += ni65.o
diff --git a/drivers/net/ariadne.c b/drivers/net/legacy/ariadne.c
similarity index 100%
rename from drivers/net/ariadne.c
rename to drivers/net/legacy/ariadne.c
diff --git a/drivers/net/ariadne.h b/drivers/net/legacy/ariadne.h
similarity index 100%
rename from drivers/net/ariadne.h
rename to drivers/net/legacy/ariadne.h
diff --git a/drivers/net/atarilance.c b/drivers/net/legacy/atarilance.c
similarity index 100%
rename from drivers/net/atarilance.c
rename to drivers/net/legacy/atarilance.c
diff --git a/drivers/net/hplance.c b/drivers/net/legacy/hplance.c
similarity index 100%
rename from drivers/net/hplance.c
rename to drivers/net/legacy/hplance.c
diff --git a/drivers/net/hplance.h b/drivers/net/legacy/hplance.h
similarity index 100%
rename from drivers/net/hplance.h
rename to drivers/net/legacy/hplance.h
diff --git a/drivers/net/lance.c b/drivers/net/legacy/lance.c
similarity index 100%
rename from drivers/net/lance.c
rename to drivers/net/legacy/lance.c
diff --git a/drivers/net/mvme147.c b/drivers/net/legacy/mvme147.c
similarity index 100%
rename from drivers/net/mvme147.c
rename to drivers/net/legacy/mvme147.c
diff --git a/drivers/net/ni65.c b/drivers/net/legacy/ni65.c
similarity index 100%
rename from drivers/net/ni65.c
rename to drivers/net/legacy/ni65.c
diff --git a/drivers/net/ni65.h b/drivers/net/legacy/ni65.h
similarity index 100%
rename from drivers/net/ni65.h
rename to drivers/net/legacy/ni65.h
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 08/15] netdev: relocate toplevel 8390 based drivers to legacy dir
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (6 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 07/15] lance: relocate legacy 7990 " Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 09/15] netdev: relocate remaining ISA 3Com cards " Paul Gortmaker
` (8 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
With the original 8 bit ISA ne1000 card being over 20 years old,
it only makes sense to relocate ne.c and all the other toplevel
8390 based driver files to the legacy dir. Largely the most recent
thing made in large quantities that was 8390 based was those
crazy PCI ne2k clones - and even they are now 10 years old.
The couple other non-toplevel drivers (arm, pcmcia), which
source 8390.h or lib8390.c are just updated in place to have
the legacy part added to their path.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 226 --------------------------------
drivers/net/Makefile | 23 ----
drivers/net/arm/etherh.c | 2 +-
drivers/net/{ => legacy}/3c503.c | 0
drivers/net/{ => legacy}/3c503.h | 0
drivers/net/{ => legacy}/8390.c | 0
drivers/net/{ => legacy}/8390.h | 0
drivers/net/{ => legacy}/8390p.c | 0
drivers/net/legacy/Kconfig | 226 ++++++++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 29 ++++
drivers/net/{ => legacy}/ac3200.c | 0
drivers/net/{ => legacy}/apne.c | 0
drivers/net/{ => legacy}/ax88796.c | 0
drivers/net/{ => legacy}/e2100.c | 0
drivers/net/{ => legacy}/es3210.c | 0
drivers/net/{ => legacy}/hp-plus.c | 0
drivers/net/{ => legacy}/hp.c | 0
drivers/net/{ => legacy}/hydra.c | 0
drivers/net/{ => legacy}/lib8390.c | 0
drivers/net/{ => legacy}/lne390.c | 0
drivers/net/{ => legacy}/mac8390.c | 0
drivers/net/{ => legacy}/ne-h8300.c | 0
drivers/net/{ => legacy}/ne.c | 0
drivers/net/{ => legacy}/ne2.c | 0
drivers/net/{ => legacy}/ne2k-pci.c | 0
drivers/net/{ => legacy}/ne3210.c | 0
drivers/net/{ => legacy}/smc-mca.c | 0
drivers/net/{ => legacy}/smc-ultra.c | 0
drivers/net/{ => legacy}/smc-ultra32.c | 0
drivers/net/{ => legacy}/stnic.c | 0
drivers/net/{ => legacy}/wd.c | 0
drivers/net/{ => legacy}/zorro8390.c | 0
drivers/net/pcmcia/axnet_cs.c | 2 +-
drivers/net/pcmcia/pcnet_cs.c | 2 +-
34 files changed, 258 insertions(+), 252 deletions(-)
rename drivers/net/{ => legacy}/3c503.c (100%)
rename drivers/net/{ => legacy}/3c503.h (100%)
rename drivers/net/{ => legacy}/8390.c (100%)
rename drivers/net/{ => legacy}/8390.h (100%)
rename drivers/net/{ => legacy}/8390p.c (100%)
rename drivers/net/{ => legacy}/ac3200.c (100%)
rename drivers/net/{ => legacy}/apne.c (100%)
rename drivers/net/{ => legacy}/ax88796.c (100%)
rename drivers/net/{ => legacy}/e2100.c (100%)
rename drivers/net/{ => legacy}/es3210.c (100%)
rename drivers/net/{ => legacy}/hp-plus.c (100%)
rename drivers/net/{ => legacy}/hp.c (100%)
rename drivers/net/{ => legacy}/hydra.c (100%)
rename drivers/net/{ => legacy}/lib8390.c (100%)
rename drivers/net/{ => legacy}/lne390.c (100%)
rename drivers/net/{ => legacy}/mac8390.c (100%)
rename drivers/net/{ => legacy}/ne-h8300.c (100%)
rename drivers/net/{ => legacy}/ne.c (100%)
rename drivers/net/{ => legacy}/ne2.c (100%)
rename drivers/net/{ => legacy}/ne2k-pci.c (100%)
rename drivers/net/{ => legacy}/ne3210.c (100%)
rename drivers/net/{ => legacy}/smc-mca.c (100%)
rename drivers/net/{ => legacy}/smc-ultra.c (100%)
rename drivers/net/{ => legacy}/smc-ultra32.c (100%)
rename drivers/net/{ => legacy}/stnic.c (100%)
rename drivers/net/{ => legacy}/wd.c (100%)
rename drivers/net/{ => legacy}/zorro8390.c (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 6ef5848..9f6315c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -249,22 +249,6 @@ config MACB
source "drivers/net/arm/Kconfig"
-config AX88796
- tristate "ASIX AX88796 NE2000 clone support"
- depends on ARM || MIPS || SUPERH
- select CRC32
- select MII
- help
- AX88796 driver, using platform bus to provide
- chip detection and resources
-
-config AX88796_93CX6
- bool "ASIX AX88796 external 93CX6 eeprom support"
- depends on AX88796
- select EEPROM_93CX6
- help
- Select this if your platform comes with an external 93CX6 eeprom.
-
config MACE
tristate "MACE (Power Mac ethernet) support"
depends on PPC_PMAC && PPC32
@@ -310,50 +294,6 @@ config A2065
To compile this driver as a module, choose M here: the module
will be called a2065.
-config HYDRA
- tristate "Hydra support"
- depends on ZORRO
- select CRC32
- help
- If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
-
- To compile this driver as a module, choose M here: the module
- will be called hydra.
-
-config ZORRO8390
- tristate "Zorro NS8390-based Ethernet support"
- depends on ZORRO
- select CRC32
- help
- This driver is for Zorro Ethernet cards using an NS8390-compatible
- chipset, like the Village Tronic Ariadne II and the Individual
- Computers X-Surf Ethernet cards. If you have such a card, say Y.
- Otherwise, say N.
-
- To compile this driver as a module, choose M here: the module
- will be called zorro8390.
-
-config APNE
- tristate "PCMCIA NE2000 support"
- depends on AMIGA_PCMCIA
- select CRC32
- help
- If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
- say N.
-
- To compile this driver as a module, choose M here: the module
- will be called apne.
-
-config MAC8390
- bool "Macintosh NS 8390 based ethernet cards"
- depends on MAC
- select CRC32
- help
- If you want to include a driver to support Nubus or LC-PDS
- Ethernet cards using an NS8390 chipset or its equivalent, say Y
- and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
config MAC89x0
tristate "Macintosh CS89x0 based ethernet cards"
depends on MAC
@@ -440,18 +380,6 @@ config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
depends on SGI_IP32=y
-config STNIC
- tristate "National DP83902AV support"
- depends on SUPERH
- select CRC32
- help
- Support for cards based on the National Semiconductor DP83902AV
- ST-NIC Serial Network Interface Controller for Twisted Pair. This
- is a 10Mbit/sec Ethernet controller. Product overview and specs at
- <http://www.national.com/pf/DP/DP83902A.html>.
-
- If unsure, say N.
-
config SH_ETH
tristate "Renesas SuperH Ethernet support"
depends on SUPERH && \
@@ -551,18 +479,6 @@ config NET_VENDOR_3COM
the questions about 3COM cards. If you say Y, you will be asked for
your specific card in the following questions.
-config EL2
- tristate "3c503 \"EtherLink II\" support"
- depends on NET_VENDOR_3COM && ISA
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c503.
-
config EL3
tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
@@ -642,61 +558,6 @@ config NET_VENDOR_SMC
the questions about Western Digital cards. If you say Y, you will be
asked for your specific card in the following questions.
-config WD80x3
- tristate "WD80*3 support"
- depends on NET_VENDOR_SMC && ISA
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called wd.
-
-config ULTRAMCA
- tristate "SMC Ultra MCA support"
- depends on NET_VENDOR_SMC && MCA
- select CRC32
- help
- If you have a network (Ethernet) card of this type and are running
- an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called smc-mca.
-
-config ULTRA
- tristate "SMC Ultra support"
- depends on NET_VENDOR_SMC && ISA
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- Important: There have been many reports that, with some motherboards
- mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
- such as some BusLogic models) causes corruption problems with many
- operating systems. The Linux smc-ultra driver has a work-around for
- this but keep it in mind if you have such a SCSI card and have
- problems.
-
- To compile this driver as a module, choose M here. The module
- will be called smc-ultra.
-
-config ULTRA32
- tristate "SMC Ultra32 EISA support"
- depends on NET_VENDOR_SMC && EISA
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called smc-ultra32.
-
config BFIN_MAC
tristate "Blackfin on-chip MAC support"
depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
@@ -985,42 +846,6 @@ config NET_ISA
the remaining ISA network card questions. If you say Y, you will be
asked for your specific card in the following questions.
-config E2100
- tristate "Cabletron E21xx support"
- depends on NET_ISA
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called e2100.
-
-config HPLAN_PLUS
- tristate "HP PCLAN+ (27247B and 27252A) support"
- depends on NET_ISA
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called hp-plus.
-
-config HPLAN
- tristate "HP PCLAN (27245 and other 27xxx series) support"
- depends on NET_ISA
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called hp.
-
config ETH16I
tristate "ICL EtherTeam 16i/32 support"
depends on NET_ISA
@@ -1032,26 +857,6 @@ config ETH16I
To compile this driver as a module, choose M here. The module
will be called eth16i.
-config NE2000
- tristate "NE2000/NE1000 support"
- depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Many Ethernet cards
- without a specific driver are compatible with NE2000.
-
- If you have a PCI NE2000 card however, say N here and Y to "PCI
- NE2000 and clone support" under "EISA, VLB, PCI and on board
- controllers" below. If you have a NE2000 card and are running on
- an MCA system (a bus system used on some IBM PS/2 computers and
- laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
- below.
-
- To compile this driver as a module, choose M here. The module
- will be called ne.
-
config SEEQ8005
tristate "SEEQ8005 support (EXPERIMENTAL)"
depends on NET_ISA && EXPERIMENTAL
@@ -1063,18 +868,6 @@ config SEEQ8005
To compile this driver as a module, choose M here. The module
will be called seeq8005.
-config NE2_MCA
- tristate "NE/2 (ne2000 MCA version) support"
- depends on MCA_LEGACY
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ne2.
-
config IBMLANA
tristate "IBM LAN Adapter/A support"
depends on MCA
@@ -1283,18 +1076,6 @@ config E100
To compile this driver as a module, choose M here. The module
will be called e100.
-config LNE390
- tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
- depends on NET_PCI && EISA && EXPERIMENTAL
- select CRC32
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called lne390.
-
config FEALNX
tristate "Myson MTD-8xx PCI Ethernet support"
depends on NET_PCI && PCI
@@ -1679,13 +1460,6 @@ config FEC_MPC52xx_MDIO
If not sure, enable.
If compiled as module, it will be called fec_mpc52xx_phy.
-config NE_H8300
- tristate "NE2000 compatible support for H8/300"
- depends on H8300
- help
- Say Y here if you want to use the NE2000 compatible
- controller on the Renesas H8/300 processor.
-
config ATL2
tristate "Atheros L2 Fast Ethernet support"
depends on PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 68c1eb9..e5015c6 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -66,7 +66,6 @@ obj-$(CONFIG_BMAC) += bmac.o
obj-$(CONFIG_VORTEX) += 3c59x.o
obj-$(CONFIG_TYPHOON) += typhoon.o
-obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
obj-$(CONFIG_PCNET32) += pcnet32.o
obj-$(CONFIG_E100) += e100.o
obj-$(CONFIG_TLAN) += tlan.o
@@ -80,7 +79,6 @@ obj-$(CONFIG_ACENIC) += acenic.o
obj-$(CONFIG_ISERIES_VETH) += iseries_veth.o
obj-$(CONFIG_NATSEMI) += natsemi.o
obj-$(CONFIG_NS83820) += ns83820.o
-obj-$(CONFIG_STNIC) += stnic.o 8390.o
obj-$(CONFIG_FEALNX) += fealnx.o
obj-$(CONFIG_TIGON3) += tg3.o
obj-$(CONFIG_BNX2) += bnx2.o
@@ -115,9 +113,6 @@ obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_NET) += Space.o loopback.o
obj-$(CONFIG_SEEQ8005) += seeq8005.o
obj-$(CONFIG_NET_SB1000) += sb1000.o
-obj-$(CONFIG_MAC8390) += mac8390.o
-obj-$(CONFIG_APNE) += apne.o 8390.o
-obj-$(CONFIG_PCMCIA_PCNET) += 8390.o
obj-$(CONFIG_HP100) += hp100.o
obj-$(CONFIG_SMC9194) += smc9194.o
obj-$(CONFIG_FEC) += fec.o
@@ -126,24 +121,9 @@ ifeq ($(CONFIG_FEC_MPC52xx_MDIO),y)
obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx_phy.o
endif
obj-$(CONFIG_68360_ENET) += 68360enet.o
-obj-$(CONFIG_WD80x3) += wd.o 8390.o
-obj-$(CONFIG_EL2) += 3c503.o 8390p.o
-obj-$(CONFIG_NE2000) += ne.o 8390p.o
-obj-$(CONFIG_NE2_MCA) += ne2.o 8390p.o
-obj-$(CONFIG_HPLAN) += hp.o 8390p.o
-obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390p.o
-obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
-obj-$(CONFIG_ULTRAMCA) += smc-mca.o 8390.o
-obj-$(CONFIG_ULTRA32) += smc-ultra32.o 8390.o
-obj-$(CONFIG_E2100) += e2100.o 8390.o
-obj-$(CONFIG_ES3210) += es3210.o 8390.o
-obj-$(CONFIG_LNE390) += lne390.o 8390.o
-obj-$(CONFIG_NE3210) += ne3210.o 8390.o
obj-$(CONFIG_SB1250_MAC) += sb1250-mac.o
obj-$(CONFIG_B44) += b44.o
obj-$(CONFIG_FORCEDETH) += forcedeth.o
-obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o
-obj-$(CONFIG_AX88796) += ax88796.o
obj-$(CONFIG_BCM63XX_ENET) += bcm63xx_enet.o
obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
@@ -185,11 +165,9 @@ obj-$(CONFIG_8139TOO) += 8139too.o
obj-$(CONFIG_CPMAC) += cpmac.o
obj-$(CONFIG_ATP) += atp.o
obj-$(CONFIG_NI5010) += ni5010.o
-obj-$(CONFIG_AC3200) += ac3200.o 8390.o
obj-$(CONFIG_SC92031) += sc92031.o
obj-$(CONFIG_ETH16I) += eth16i.o
-obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
@@ -197,7 +175,6 @@ obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
obj-$(CONFIG_A2065) += a2065.o
-obj-$(CONFIG_HYDRA) += hydra.o 8390.o
obj-$(CONFIG_CS89x0) += cs89x0.o
obj-$(CONFIG_MACSONIC) += macsonic.o
obj-$(CONFIG_MACMACE) += macmace.o
diff --git a/drivers/net/arm/etherh.c b/drivers/net/arm/etherh.c
index 4af235d..0e60f86 100644
--- a/drivers/net/arm/etherh.c
+++ b/drivers/net/arm/etherh.c
@@ -65,7 +65,7 @@
static char version[] __initdata =
"EtherH/EtherM Driver (c) 2002-2004 Russell King " DRV_VERSION "\n";
-#include "../lib8390.c"
+#include "../legacy/lib8390.c"
static unsigned int net_debug = NET_DEBUG;
diff --git a/drivers/net/3c503.c b/drivers/net/legacy/3c503.c
similarity index 100%
rename from drivers/net/3c503.c
rename to drivers/net/legacy/3c503.c
diff --git a/drivers/net/3c503.h b/drivers/net/legacy/3c503.h
similarity index 100%
rename from drivers/net/3c503.h
rename to drivers/net/legacy/3c503.h
diff --git a/drivers/net/8390.c b/drivers/net/legacy/8390.c
similarity index 100%
rename from drivers/net/8390.c
rename to drivers/net/legacy/8390.c
diff --git a/drivers/net/8390.h b/drivers/net/legacy/8390.h
similarity index 100%
rename from drivers/net/8390.h
rename to drivers/net/legacy/8390.h
diff --git a/drivers/net/8390p.c b/drivers/net/legacy/8390p.c
similarity index 100%
rename from drivers/net/8390p.c
rename to drivers/net/legacy/8390p.c
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index 32bd91a..74644b8 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -321,3 +321,229 @@ config LANCE
To compile this driver as a module, choose M here: the module
will be called lance. This is recommended.
+
+config AX88796
+ tristate "ASIX AX88796 NE2000 clone support"
+ depends on ARM || MIPS || SUPERH
+ select CRC32
+ select MII
+ help
+ AX88796 driver, using platform bus to provide
+ chip detection and resources
+
+config AX88796_93CX6
+ bool "ASIX AX88796 external 93CX6 eeprom support"
+ depends on AX88796
+ select EEPROM_93CX6
+ help
+ Select this if your platform comes with an external 93CX6 eeprom.
+
+config HYDRA
+ tristate "Hydra support"
+ depends on ZORRO
+ select CRC32
+ help
+ If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called hydra.
+
+config ZORRO8390
+ tristate "Zorro NS8390-based Ethernet support"
+ depends on ZORRO
+ select CRC32
+ help
+ This driver is for Zorro Ethernet cards using an NS8390-compatible
+ chipset, like the Village Tronic Ariadne II and the Individual
+ Computers X-Surf Ethernet cards. If you have such a card, say Y.
+ Otherwise, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called zorro8390.
+
+config APNE
+ tristate "PCMCIA NE2000 support"
+ depends on AMIGA_PCMCIA
+ select CRC32
+ help
+ If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
+ say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called apne.
+
+config MAC8390
+ bool "Macintosh NS 8390 based ethernet cards"
+ depends on MAC
+ select CRC32
+ help
+ If you want to include a driver to support Nubus or LC-PDS
+ Ethernet cards using an NS8390 chipset or its equivalent, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+config STNIC
+ tristate "National DP83902AV support"
+ depends on SUPERH
+ select CRC32
+ help
+ Support for cards based on the National Semiconductor DP83902AV
+ ST-NIC Serial Network Interface Controller for Twisted Pair. This
+ is a 10Mbit/sec Ethernet controller. Product overview and specs at
+ <http://www.national.com/pf/DP/DP83902A.html>.
+
+ If unsure, say N.
+
+config EL2
+ tristate "3c503 \"EtherLink II\" support"
+ depends on NET_VENDOR_3COM && ISA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c503.
+
+config WD80x3
+ tristate "WD80*3 support"
+ depends on NET_VENDOR_SMC && ISA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called wd.
+
+config ULTRAMCA
+ tristate "SMC Ultra MCA support"
+ depends on NET_VENDOR_SMC && MCA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type and are running
+ an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
+ available from <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called smc-mca.
+
+config ULTRA
+ tristate "SMC Ultra support"
+ depends on NET_VENDOR_SMC && ISA
+ select CRC32
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Important: There have been many reports that, with some motherboards
+ mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
+ such as some BusLogic models) causes corruption problems with many
+ operating systems. The Linux smc-ultra driver has a work-around for
+ this but keep it in mind if you have such a SCSI card and have
+ problems.
+
+ To compile this driver as a module, choose M here. The module
+ will be called smc-ultra.
+
+config ULTRA32
+ tristate "SMC Ultra32 EISA support"
+ depends on NET_VENDOR_SMC && EISA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called smc-ultra32.
+
+config E2100
+ tristate "Cabletron E21xx support"
+ depends on NET_ISA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called e2100.
+
+config HPLAN_PLUS
+ tristate "HP PCLAN+ (27247B and 27252A) support"
+ depends on NET_ISA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called hp-plus.
+
+config HPLAN
+ tristate "HP PCLAN (27245 and other 27xxx series) support"
+ depends on NET_ISA
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called hp.
+
+config NE2000
+ tristate "NE2000/NE1000 support"
+ depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
+ select CRC32
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>. Many Ethernet cards
+ without a specific driver are compatible with NE2000.
+
+ If you have a PCI NE2000 card however, say N here and Y to "PCI
+ NE2000 and clone support" under "EISA, VLB, PCI and on board
+ controllers" below. If you have a NE2000 card and are running on
+ an MCA system (a bus system used on some IBM PS/2 computers and
+ laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
+ below.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ne.
+
+config NE2_MCA
+ tristate "NE/2 (ne2000 MCA version) support"
+ depends on MCA_LEGACY
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ne2.
+
+config LNE390
+ tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
+ depends on NET_PCI && EISA && EXPERIMENTAL
+ select CRC32
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called lne390.
+
+config NE_H8300
+ tristate "NE2000 compatible support for H8/300"
+ depends on H8300
+ help
+ Say Y here if you want to use the NE2000 compatible
+ controller on the Renesas H8/300 processor.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index 0eb679c..eefacda 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -37,3 +37,32 @@ obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
obj-$(CONFIG_LANCE) += lance.o
obj-$(CONFIG_MVME147_NET) += mvme147.o 7990.o
obj-$(CONFIG_NI65) += ni65.o
+
+# ISA 8390 based
+obj-$(CONFIG_E2100) += e2100.o 8390.o
+obj-$(CONFIG_EL2) += 3c503.o 8390p.o
+obj-$(CONFIG_HPLAN) += hp.o 8390p.o
+obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390p.o
+obj-$(CONFIG_NE2000) += ne.o 8390p.o
+obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
+obj-$(CONFIG_WD80x3) += wd.o 8390.o
+
+# EISA 8390 based
+obj-$(CONFIG_AC3200) += ac3200.o 8390.o
+obj-$(CONFIG_ES3210) += es3210.o 8390.o
+obj-$(CONFIG_LNE390) += lne390.o 8390.o
+obj-$(CONFIG_NE3210) += ne3210.o 8390.o
+obj-$(CONFIG_ULTRA32) += smc-ultra32.o 8390.o
+
+# Other 8390 based hardware.
+obj-$(CONFIG_APNE) += apne.o 8390.o
+obj-$(CONFIG_AX88796) += ax88796.o
+obj-$(CONFIG_HYDRA) += hydra.o 8390.o
+obj-$(CONFIG_MAC8390) += mac8390.o
+obj-$(CONFIG_NE2_MCA) += ne2.o 8390p.o
+obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
+obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o
+obj-$(CONFIG_PCMCIA_PCNET) += 8390.o
+obj-$(CONFIG_ULTRAMCA) += smc-mca.o 8390.o
+obj-$(CONFIG_STNIC) += stnic.o 8390.o
+obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
diff --git a/drivers/net/ac3200.c b/drivers/net/legacy/ac3200.c
similarity index 100%
rename from drivers/net/ac3200.c
rename to drivers/net/legacy/ac3200.c
diff --git a/drivers/net/apne.c b/drivers/net/legacy/apne.c
similarity index 100%
rename from drivers/net/apne.c
rename to drivers/net/legacy/apne.c
diff --git a/drivers/net/ax88796.c b/drivers/net/legacy/ax88796.c
similarity index 100%
rename from drivers/net/ax88796.c
rename to drivers/net/legacy/ax88796.c
diff --git a/drivers/net/e2100.c b/drivers/net/legacy/e2100.c
similarity index 100%
rename from drivers/net/e2100.c
rename to drivers/net/legacy/e2100.c
diff --git a/drivers/net/es3210.c b/drivers/net/legacy/es3210.c
similarity index 100%
rename from drivers/net/es3210.c
rename to drivers/net/legacy/es3210.c
diff --git a/drivers/net/hp-plus.c b/drivers/net/legacy/hp-plus.c
similarity index 100%
rename from drivers/net/hp-plus.c
rename to drivers/net/legacy/hp-plus.c
diff --git a/drivers/net/hp.c b/drivers/net/legacy/hp.c
similarity index 100%
rename from drivers/net/hp.c
rename to drivers/net/legacy/hp.c
diff --git a/drivers/net/hydra.c b/drivers/net/legacy/hydra.c
similarity index 100%
rename from drivers/net/hydra.c
rename to drivers/net/legacy/hydra.c
diff --git a/drivers/net/lib8390.c b/drivers/net/legacy/lib8390.c
similarity index 100%
rename from drivers/net/lib8390.c
rename to drivers/net/legacy/lib8390.c
diff --git a/drivers/net/lne390.c b/drivers/net/legacy/lne390.c
similarity index 100%
rename from drivers/net/lne390.c
rename to drivers/net/legacy/lne390.c
diff --git a/drivers/net/mac8390.c b/drivers/net/legacy/mac8390.c
similarity index 100%
rename from drivers/net/mac8390.c
rename to drivers/net/legacy/mac8390.c
diff --git a/drivers/net/ne-h8300.c b/drivers/net/legacy/ne-h8300.c
similarity index 100%
rename from drivers/net/ne-h8300.c
rename to drivers/net/legacy/ne-h8300.c
diff --git a/drivers/net/ne.c b/drivers/net/legacy/ne.c
similarity index 100%
rename from drivers/net/ne.c
rename to drivers/net/legacy/ne.c
diff --git a/drivers/net/ne2.c b/drivers/net/legacy/ne2.c
similarity index 100%
rename from drivers/net/ne2.c
rename to drivers/net/legacy/ne2.c
diff --git a/drivers/net/ne2k-pci.c b/drivers/net/legacy/ne2k-pci.c
similarity index 100%
rename from drivers/net/ne2k-pci.c
rename to drivers/net/legacy/ne2k-pci.c
diff --git a/drivers/net/ne3210.c b/drivers/net/legacy/ne3210.c
similarity index 100%
rename from drivers/net/ne3210.c
rename to drivers/net/legacy/ne3210.c
diff --git a/drivers/net/smc-mca.c b/drivers/net/legacy/smc-mca.c
similarity index 100%
rename from drivers/net/smc-mca.c
rename to drivers/net/legacy/smc-mca.c
diff --git a/drivers/net/smc-ultra.c b/drivers/net/legacy/smc-ultra.c
similarity index 100%
rename from drivers/net/smc-ultra.c
rename to drivers/net/legacy/smc-ultra.c
diff --git a/drivers/net/smc-ultra32.c b/drivers/net/legacy/smc-ultra32.c
similarity index 100%
rename from drivers/net/smc-ultra32.c
rename to drivers/net/legacy/smc-ultra32.c
diff --git a/drivers/net/stnic.c b/drivers/net/legacy/stnic.c
similarity index 100%
rename from drivers/net/stnic.c
rename to drivers/net/legacy/stnic.c
diff --git a/drivers/net/wd.c b/drivers/net/legacy/wd.c
similarity index 100%
rename from drivers/net/wd.c
rename to drivers/net/legacy/wd.c
diff --git a/drivers/net/zorro8390.c b/drivers/net/legacy/zorro8390.c
similarity index 100%
rename from drivers/net/zorro8390.c
rename to drivers/net/legacy/zorro8390.c
diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c
index d2e166e..65314e8 100644
--- a/drivers/net/pcmcia/axnet_cs.c
+++ b/drivers/net/pcmcia/axnet_cs.c
@@ -38,7 +38,7 @@
#include <linux/etherdevice.h>
#include <linux/crc32.h>
#include <linux/mii.h>
-#include "../8390.h"
+#include "../legacy/8390.h"
#include <pcmcia/cistpl.h>
#include <pcmcia/ciscode.h>
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index 03096c8..6e7731e 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -41,7 +41,7 @@
#include <linux/log2.h>
#include <linux/etherdevice.h>
#include <linux/mii.h>
-#include "../8390.h"
+#include "../legacy/8390.h"
#include <pcmcia/cistpl.h>
#include <pcmcia/ciscode.h>
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 09/15] netdev: relocate remaining ISA 3Com cards to legacy dir
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (7 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 08/15] netdev: relocate toplevel 8390 based drivers to legacy dir Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 10/15] netdev: relocate more one-off drivers to the " Paul Gortmaker
` (7 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
The last mainstream motherboards produced with ISA slots were
some P3 Coppermine socket370 platforms with a single ISA slot
from around the turn of the century.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 26 --------------------------
drivers/net/Makefile | 2 --
drivers/net/{ => legacy}/3c509.c | 0
drivers/net/{ => legacy}/3c515.c | 0
drivers/net/legacy/Kconfig | 26 ++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 4 ++++
6 files changed, 30 insertions(+), 28 deletions(-)
rename drivers/net/{ => legacy}/3c509.c (100%)
rename drivers/net/{ => legacy}/3c515.c (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 9f6315c..5b6c3e9 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -479,32 +479,6 @@ config NET_VENDOR_3COM
the questions about 3COM cards. If you say Y, you will be asked for
your specific card in the following questions.
-config EL3
- tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
- depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
- ---help---
- If you have a network (Ethernet) card belonging to the 3Com
- EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
- from <http://www.tldp.org/docs.html#howto>.
-
- If your card is not working you may need to use the DOS
- setup disk to disable Plug & Play mode, and to select the default
- media type.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c509.
-
-config 3C515
- tristate "3c515 ISA \"Fast EtherLink\""
- depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
- help
- If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
- network card, say Y and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called 3c515.
-
config VORTEX
tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
depends on NET_VENDOR_3COM && (PCI || EISA)
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index e5015c6..790bb6c 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -158,8 +158,6 @@ obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_AT1700) += at1700.o
obj-$(CONFIG_IBMLANA) += ibmlana.o
-obj-$(CONFIG_EL3) += 3c509.o
-obj-$(CONFIG_3C515) += 3c515.o
obj-$(CONFIG_8139CP) += 8139cp.o
obj-$(CONFIG_8139TOO) += 8139too.o
obj-$(CONFIG_CPMAC) += cpmac.o
diff --git a/drivers/net/3c509.c b/drivers/net/legacy/3c509.c
similarity index 100%
rename from drivers/net/3c509.c
rename to drivers/net/legacy/3c509.c
diff --git a/drivers/net/3c515.c b/drivers/net/legacy/3c515.c
similarity index 100%
rename from drivers/net/3c515.c
rename to drivers/net/legacy/3c515.c
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index 74644b8..c4cdc99 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -15,6 +15,32 @@ config EL1
To compile this driver as a module, choose M here. The module
will be called 3c501.
+config EL3
+ tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
+ depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
+ ---help---
+ If you have a network (Ethernet) card belonging to the 3Com
+ EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
+ from <http://www.tldp.org/docs.html#howto>.
+
+ If your card is not working you may need to use the DOS
+ setup disk to disable Plug & Play mode, and to select the default
+ media type.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c509.
+
+config 3C515
+ tristate "3c515 ISA \"Fast EtherLink\""
+ depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
+ help
+ If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
+ network card, say Y and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called 3c515.
+
config DE600
tristate "D-Link DE600 pocket adapter support"
depends on NET_POCKET && PARPORT
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index eefacda..5341a1d 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -66,3 +66,7 @@ obj-$(CONFIG_PCMCIA_PCNET) += 8390.o
obj-$(CONFIG_ULTRAMCA) += smc-mca.o 8390.o
obj-$(CONFIG_STNIC) += stnic.o 8390.o
obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
+
+# Other random one-off cards
+obj-$(CONFIG_EL3) += 3c509.o
+obj-$(CONFIG_3C515) += 3c515.o
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 10/15] netdev: relocate more one-off drivers to the legacy dir
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (8 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 09/15] netdev: relocate remaining ISA 3Com cards " Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 11/15] netdev: kill off the concept of NET_VENDOR_FOO Paul Gortmaker
` (6 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
These one-off ISA/EISA/MCA drivers have been around since the
beginning of time; relocate them off to the legacy dir.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 76 -----------------------------------
drivers/net/Makefile | 5 --
drivers/net/legacy/Kconfig | 76 +++++++++++++++++++++++++++++++++++
drivers/net/legacy/Makefile | 5 ++
drivers/net/{ => legacy}/at1700.c | 0
drivers/net/{ => legacy}/eth16i.c | 0
drivers/net/{ => legacy}/ibmlana.c | 0
drivers/net/{ => legacy}/ibmlana.h | 0
drivers/net/{ => legacy}/ni5010.c | 0
drivers/net/{ => legacy}/ni5010.h | 0
drivers/net/{ => legacy}/seeq8005.c | 0
drivers/net/{ => legacy}/seeq8005.h | 0
drivers/net/{ => legacy}/smc9194.c | 0
drivers/net/{ => legacy}/smc9194.h | 0
14 files changed, 81 insertions(+), 81 deletions(-)
rename drivers/net/{ => legacy}/at1700.c (100%)
rename drivers/net/{ => legacy}/eth16i.c (100%)
rename drivers/net/{ => legacy}/ibmlana.c (100%)
rename drivers/net/{ => legacy}/ibmlana.h (100%)
rename drivers/net/{ => legacy}/ni5010.c (100%)
rename drivers/net/{ => legacy}/ni5010.h (100%)
rename drivers/net/{ => legacy}/seeq8005.c (100%)
rename drivers/net/{ => legacy}/seeq8005.h (100%)
rename drivers/net/{ => legacy}/smc9194.c (100%)
rename drivers/net/{ => legacy}/smc9194.h (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 5b6c3e9..b5adf52 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -586,21 +586,6 @@ config BFIN_MAC_USE_HWSTAMP
help
To support the IEEE 1588 Precision Time Protocol (PTP), select y here
-config SMC9194
- tristate "SMC 9194 support"
- depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
- select CRC32
- ---help---
- This is support for the SMC9xxx based Ethernet cards. Choose this
- option if you have a DELL laptop with the docking station, or
- another SMC9192/9194 based chipset. Say Y if you want it compiled
- into the kernel, and read the file
- <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called smc9194.
-
config SMC91X
tristate "SMC 91C9x/91C1xxx support"
select CRC32
@@ -755,18 +740,6 @@ config NET_VENDOR_RACAL
the questions about NI cards. If you say Y, you will be asked for
your specific card in the following questions.
-config NI5010
- tristate "NI5010 support (EXPERIMENTAL)"
- depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Note that this is still
- experimental code.
-
- To compile this driver as a module, choose M here. The module
- will be called ni5010.
-
config DNET
tristate "Dave ethernet support (DNET)"
depends on NET_ETHERNET && HAS_IOMEM
@@ -780,18 +753,6 @@ config DNET
source "drivers/net/tulip/Kconfig"
-config AT1700
- tristate "AT1700/1720 support (EXPERIMENTAL)"
- depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called at1700.
-
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
depends on ISA || EISA || PCI
@@ -820,43 +781,6 @@ config NET_ISA
the remaining ISA network card questions. If you say Y, you will be
asked for your specific card in the following questions.
-config ETH16I
- tristate "ICL EtherTeam 16i/32 support"
- depends on NET_ISA
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called eth16i.
-
-config SEEQ8005
- tristate "SEEQ8005 support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL
- help
- This is a driver for the SEEQ 8005 network (Ethernet) card. If this
- is for you, read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called seeq8005.
-
-config IBMLANA
- tristate "IBM LAN Adapter/A support"
- depends on MCA
- ---help---
- This is a Micro Channel Ethernet adapter. You need to set
- CONFIG_MCA to use this driver. It is both available as an in-kernel
- driver and as a module.
-
- To compile this driver as a module, choose M here. The only
- currently supported card is the IBM LAN Adapter/A for Ethernet. It
- will both support 16K and 32K memory windows, however a 32K window
- gives a better security against packet losses. Usage of multiple
- boards with this driver should be possible, but has not been tested
- up to now due to lack of hardware.
-
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
depends on PPC_PSERIES
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 790bb6c..3182544 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -111,10 +111,8 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac/
obj-$(CONFIG_SUNDANCE) += sundance.o
obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_NET) += Space.o loopback.o
-obj-$(CONFIG_SEEQ8005) += seeq8005.o
obj-$(CONFIG_NET_SB1000) += sb1000.o
obj-$(CONFIG_HP100) += hp100.o
-obj-$(CONFIG_SMC9194) += smc9194.o
obj-$(CONFIG_FEC) += fec.o
obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx.o
ifeq ($(CONFIG_FEC_MPC52xx_MDIO),y)
@@ -156,8 +154,6 @@ obj-$(CONFIG_MACVLAN) += macvlan.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
-obj-$(CONFIG_AT1700) += at1700.o
-obj-$(CONFIG_IBMLANA) += ibmlana.o
obj-$(CONFIG_8139CP) += 8139cp.o
obj-$(CONFIG_8139TOO) += 8139too.o
obj-$(CONFIG_CPMAC) += cpmac.o
@@ -165,7 +161,6 @@ obj-$(CONFIG_ATP) += atp.o
obj-$(CONFIG_NI5010) += ni5010.o
obj-$(CONFIG_SC92031) += sc92031.o
-obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index c4cdc99..2da3ac7 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -278,6 +278,18 @@ config ZNET
by this driver. Read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
+config NI5010
+ tristate "NI5010 support (EXPERIMENTAL)"
+ depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>. Note that this is still
+ experimental code.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ni5010.
+
config NI52
tristate "NI5210 support"
depends on NET_VENDOR_RACAL && ISA
@@ -573,3 +585,67 @@ config NE_H8300
help
Say Y here if you want to use the NE2000 compatible
controller on the Renesas H8/300 processor.
+
+config AT1700
+ tristate "AT1700/1720 support (EXPERIMENTAL)"
+ depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
+ select CRC32
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called at1700.
+
+config ETH16I
+ tristate "ICL EtherTeam 16i/32 support"
+ depends on NET_ISA
+ help
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called eth16i.
+
+config SEEQ8005
+ tristate "SEEQ8005 support (EXPERIMENTAL)"
+ depends on NET_ISA && EXPERIMENTAL
+ help
+ This is a driver for the SEEQ 8005 network (Ethernet) card. If this
+ is for you, read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called seeq8005.
+
+config IBMLANA
+ tristate "IBM LAN Adapter/A support"
+ depends on MCA
+ ---help---
+ This is a Micro Channel Ethernet adapter. You need to set
+ CONFIG_MCA to use this driver. It is both available as an in-kernel
+ driver and as a module.
+
+ To compile this driver as a module, choose M here. The only
+ currently supported card is the IBM LAN Adapter/A for Ethernet. It
+ will both support 16K and 32K memory windows, however a 32K window
+ gives a better security against packet losses. Usage of multiple
+ boards with this driver should be possible, but has not been tested
+ up to now due to lack of hardware.
+
+config SMC9194
+ tristate "SMC 9194 support"
+ depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
+ select CRC32
+ ---help---
+ This is support for the SMC9xxx based Ethernet cards. Choose this
+ option if you have a DELL laptop with the docking station, or
+ another SMC9192/9194 based chipset. Say Y if you want it compiled
+ into the kernel, and read the file
+ <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
+ available from <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called smc9194.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index 5341a1d..0268706 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -70,3 +70,8 @@ obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
# Other random one-off cards
obj-$(CONFIG_EL3) += 3c509.o
obj-$(CONFIG_3C515) += 3c515.o
+obj-$(CONFIG_SEEQ8005) += seeq8005.o
+obj-$(CONFIG_AT1700) += at1700.o
+obj-$(CONFIG_IBMLANA) += ibmlana.o
+obj-$(CONFIG_ETH16I) += eth16i.o
+obj-$(CONFIG_SMC9194) += smc9194.o
diff --git a/drivers/net/at1700.c b/drivers/net/legacy/at1700.c
similarity index 100%
rename from drivers/net/at1700.c
rename to drivers/net/legacy/at1700.c
diff --git a/drivers/net/eth16i.c b/drivers/net/legacy/eth16i.c
similarity index 100%
rename from drivers/net/eth16i.c
rename to drivers/net/legacy/eth16i.c
diff --git a/drivers/net/ibmlana.c b/drivers/net/legacy/ibmlana.c
similarity index 100%
rename from drivers/net/ibmlana.c
rename to drivers/net/legacy/ibmlana.c
diff --git a/drivers/net/ibmlana.h b/drivers/net/legacy/ibmlana.h
similarity index 100%
rename from drivers/net/ibmlana.h
rename to drivers/net/legacy/ibmlana.h
diff --git a/drivers/net/ni5010.c b/drivers/net/legacy/ni5010.c
similarity index 100%
rename from drivers/net/ni5010.c
rename to drivers/net/legacy/ni5010.c
diff --git a/drivers/net/ni5010.h b/drivers/net/legacy/ni5010.h
similarity index 100%
rename from drivers/net/ni5010.h
rename to drivers/net/legacy/ni5010.h
diff --git a/drivers/net/seeq8005.c b/drivers/net/legacy/seeq8005.c
similarity index 100%
rename from drivers/net/seeq8005.c
rename to drivers/net/legacy/seeq8005.c
diff --git a/drivers/net/seeq8005.h b/drivers/net/legacy/seeq8005.h
similarity index 100%
rename from drivers/net/seeq8005.h
rename to drivers/net/legacy/seeq8005.h
diff --git a/drivers/net/smc9194.c b/drivers/net/legacy/smc9194.c
similarity index 100%
rename from drivers/net/smc9194.c
rename to drivers/net/legacy/smc9194.c
diff --git a/drivers/net/smc9194.h b/drivers/net/legacy/smc9194.h
similarity index 100%
rename from drivers/net/smc9194.h
rename to drivers/net/legacy/smc9194.h
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 11/15] netdev: kill off the concept of NET_VENDOR_FOO
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (9 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 10/15] netdev: relocate more one-off drivers to the " Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 12/15] netdev: relocate sb1000 ISA cable modem driver to legacy Paul Gortmaker
` (5 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
Back when all the Kconfig options were in one flat list, there
were vendor specific Kconfig options which did nothing other
than hide or display the list of vendor specific Kconfig options.
With all the old driver options all squirreled away in the legacy
dir, we can simply drop these in place of the single new option
NETDEVICES_LEGACY.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 43 ++-----------------------------------------
drivers/net/legacy/Kconfig | 22 +++++++++++-----------
2 files changed, 13 insertions(+), 52 deletions(-)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index b5adf52..7a0912e 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -466,22 +466,9 @@ config SUNVNET
help
Support for virtual network devices under Sun Logical Domains.
-config NET_VENDOR_3COM
- bool "3COM cards"
- depends on ISA || EISA || MCA || PCI
- help
- If you have a network (Ethernet) card belonging to this class, say Y
- and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- Note that the answer to this question doesn't directly affect the
- kernel: saying N will just cause the configurator to skip all
- the questions about 3COM cards. If you say Y, you will be asked for
- your specific card in the following questions.
-
config VORTEX
tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
- depends on NET_VENDOR_3COM && (PCI || EISA)
+ depends on (PCI || EISA)
select MII
---help---
This option enables driver support for a large number of 10Mbps and
@@ -503,7 +490,7 @@ config VORTEX
config TYPHOON
tristate "3cr990 series \"Typhoon\" support"
- depends on NET_VENDOR_3COM && PCI
+ depends on PCI
select CRC32
---help---
This option enables driver support for the 3cr990 series of cards:
@@ -519,19 +506,6 @@ config TYPHOON
To compile this driver as a module, choose M here. The module
will be called typhoon.
-config NET_VENDOR_SMC
- bool "Western Digital/SMC cards"
- depends on ISA || MCA || EISA || MAC
- help
- If you have a network (Ethernet) card belonging to this class, say Y
- and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- Note that the answer to this question doesn't directly affect the
- kernel: saying N will just cause the configurator to skip all
- the questions about Western Digital cards. If you say Y, you will be
- asked for your specific card in the following questions.
-
config BFIN_MAC
tristate "Blackfin on-chip MAC support"
depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
@@ -727,19 +701,6 @@ config SMSC911X
<file:Documentation/networking/net-modules.txt>. The module
will be called smsc911x.
-config NET_VENDOR_RACAL
- bool "Racal-Interlan (Micom) NI cards"
- depends on ISA
- help
- If you have a network (Ethernet) card belonging to this class, such
- as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
- Note that the answer to this question doesn't directly affect the
- kernel: saying N will just cause the configurator to skip all
- the questions about NI cards. If you say Y, you will be asked for
- your specific card in the following questions.
-
config DNET
tristate "Dave ethernet support (DNET)"
depends on NET_ETHERNET && HAS_IOMEM
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index 2da3ac7..96d667e 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -3,7 +3,7 @@
config EL1
tristate "3c501 \"EtherLink\" support"
- depends on NET_VENDOR_3COM && ISA
+ depends on ISA
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -17,7 +17,7 @@ config EL1
config EL3
tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
- depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
+ depends on (ISA || EISA || MCA)
---help---
If you have a network (Ethernet) card belonging to the 3Com
EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
@@ -32,7 +32,7 @@ config EL3
config 3C515
tristate "3c515 ISA \"Fast EtherLink\""
- depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
+ depends on (ISA || EISA) && ISA_DMA_API
help
If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
network card, say Y and read the Ethernet-HOWTO, available from
@@ -190,7 +190,7 @@ config SNI_82596
config ELPLUS
tristate "3c505 \"EtherLink Plus\" support"
- depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
+ depends on ISA && ISA_DMA_API
---help---
Information about this network (Ethernet) card can be found in
<file:Documentation/networking/3c505.txt>. If you have a card of
@@ -202,7 +202,7 @@ config ELPLUS
config EL16
tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
- depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
+ depends on ISA && EXPERIMENTAL
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -213,7 +213,7 @@ config EL16
config ELMC
tristate "3c523 \"EtherLink/MC\" support"
- depends on NET_VENDOR_3COM && MCA_LEGACY
+ depends on MCA_LEGACY
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -224,7 +224,7 @@ config ELMC
config ELMC_II
tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
- depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
+ depends on MCA && MCA_LEGACY
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -280,7 +280,7 @@ config ZNET
config NI5010
tristate "NI5010 support (EXPERIMENTAL)"
- depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
+ depends on ISA && EXPERIMENTAL && BROKEN_ON_SMP
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -292,7 +292,7 @@ config NI5010
config NI52
tristate "NI5210 support"
- depends on NET_VENDOR_RACAL && ISA
+ depends on ISA
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -303,7 +303,7 @@ config NI52
config NI65
tristate "NI6510 support"
- depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
+ depends on ISA && ISA_DMA_API
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -637,7 +637,7 @@ config IBMLANA
config SMC9194
tristate "SMC 9194 support"
- depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
+ depends on ISA || MAC && BROKEN
select CRC32
---help---
This is support for the SMC9xxx based Ethernet cards. Choose this
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 12/15] netdev: relocate sb1000 ISA cable modem driver to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (10 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 11/15] netdev: kill off the concept of NET_VENDOR_FOO Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 13/15] netdev: kill off NET_ISA Kconfig option Paul Gortmaker
` (4 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
As yet another ISA device, this board is limited to being used
in motherboards that are 10+ years old. Hence relocate it to
the legacy dir.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 24 ------------------------
drivers/net/Makefile | 1 -
drivers/net/legacy/Kconfig | 24 ++++++++++++++++++++++++
drivers/net/legacy/Makefile | 1 +
drivers/net/{ => legacy}/sb1000.c | 0
5 files changed, 25 insertions(+), 25 deletions(-)
rename drivers/net/{ => legacy}/sb1000.c (100%)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 7a0912e..707c9f8c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -168,30 +168,6 @@ config VETH
When one end receives the packet it appears on its pair and vice
versa.
-config NET_SB1000
- tristate "General Instruments Surfboard 1000"
- depends on PNP
- ---help---
- This is a driver for the General Instrument (also known as
- NextLevel) SURFboard 1000 internal
- cable modem. This is an ISA card which is used by a number of cable
- TV companies to provide cable modem access. It's a one-way
- downstream-only cable modem, meaning that your upstream net link is
- provided by your regular phone modem.
-
- At present this driver only compiles as a module, so say M here if
- you have this card. The module will be called sb1000. Then read
- <file:Documentation/networking/README.sb1000> for information on how
- to use this module, as it needs special ppp scripts for establishing
- a connection. Further documentation and the necessary scripts can be
- found at:
-
- <http://www.jacksonville.net/~fventuri/>
- <http://home.adelphia.net/~siglercm/sb1000.html>
- <http://linuxpower.cx/~cable/>
-
- If you don't have this card, of course say N.
-
source "drivers/net/arcnet/Kconfig"
config MII
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 3182544..ff138b0 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -111,7 +111,6 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac/
obj-$(CONFIG_SUNDANCE) += sundance.o
obj-$(CONFIG_HAMACHI) += hamachi.o
obj-$(CONFIG_NET) += Space.o loopback.o
-obj-$(CONFIG_NET_SB1000) += sb1000.o
obj-$(CONFIG_HP100) += hp100.o
obj-$(CONFIG_FEC) += fec.o
obj-$(CONFIG_FEC_MPC52xx) += fec_mpc52xx.o
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index 96d667e..b9ea8ed 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -649,3 +649,27 @@ config SMC9194
To compile this driver as a module, choose M here. The module
will be called smc9194.
+
+config NET_SB1000
+ tristate "General Instruments Surfboard 1000"
+ depends on PNP
+ ---help---
+ This is a driver for the General Instrument (also known as
+ NextLevel) SURFboard 1000 internal
+ cable modem. This is an ISA card which is used by a number of cable
+ TV companies to provide cable modem access. It's a one-way
+ downstream-only cable modem, meaning that your upstream net link is
+ provided by your regular phone modem.
+
+ At present this driver only compiles as a module, so say M here if
+ you have this card. The module will be called sb1000. Then read
+ <file:Documentation/networking/README.sb1000> for information on how
+ to use this module, as it needs special ppp scripts for establishing
+ a connection. Further documentation and the necessary scripts can be
+ found at:
+
+ <http://www.jacksonville.net/~fventuri/>
+ <http://home.adelphia.net/~siglercm/sb1000.html>
+ <http://linuxpower.cx/~cable/>
+
+ If you don't have this card, of course say N.
diff --git a/drivers/net/legacy/Makefile b/drivers/net/legacy/Makefile
index 0268706..b703327 100644
--- a/drivers/net/legacy/Makefile
+++ b/drivers/net/legacy/Makefile
@@ -75,3 +75,4 @@ obj-$(CONFIG_AT1700) += at1700.o
obj-$(CONFIG_IBMLANA) += ibmlana.o
obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_SMC9194) += smc9194.o
+obj-$(CONFIG_NET_SB1000) += sb1000.o
diff --git a/drivers/net/sb1000.c b/drivers/net/legacy/sb1000.c
similarity index 100%
rename from drivers/net/sb1000.c
rename to drivers/net/legacy/sb1000.c
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 13/15] netdev: kill off NET_ISA Kconfig option
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (11 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 12/15] netdev: relocate sb1000 ISA cable modem driver to legacy Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 14/15] MAINTAINERS: updates for new drivers/net/legacy dir Paul Gortmaker
` (3 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
The NET_ISA option was like the NET_VENDOR_<xyz> options in that it
just hid a bunch of config options from being presented. For those
drivers that depended on it to provide the ISA dependency, just have
them depend on ISA directly.
The NETDEV_LEGACY option is used to hide all these NET_ISA options,
so that the end number of options presented is largely unchanged.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/Kconfig | 17 -----------------
drivers/net/legacy/Kconfig | 22 +++++++++++-----------
2 files changed, 11 insertions(+), 28 deletions(-)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 707c9f8c..0433c35 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -701,23 +701,6 @@ config HP100
To compile this driver as a module, choose M here. The module
will be called hp100.
-config NET_ISA
- bool "Other ISA cards"
- depends on ISA
- ---help---
- If your network (Ethernet) card hasn't been mentioned yet and its
- bus system (that's the way the cards talks to the other components
- of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
- Make sure you know the name of your card. Read the Ethernet-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
- If unsure, say Y.
-
- Note that the answer to this question doesn't directly affect the
- kernel: saying N will just cause the configurator to skip all
- the remaining ISA network card questions. If you say Y, you will be
- asked for your specific card in the following questions.
-
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
depends on PPC_PSERIES
diff --git a/drivers/net/legacy/Kconfig b/drivers/net/legacy/Kconfig
index b9ea8ed..5736338 100644
--- a/drivers/net/legacy/Kconfig
+++ b/drivers/net/legacy/Kconfig
@@ -108,7 +108,7 @@ config DEPCA
config EWRK3
tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
- depends on NET_ISA
+ depends on ISA
select CRC32
---help---
This driver supports the DE203, DE204 and DE205 network (Ethernet)
@@ -235,7 +235,7 @@ config ELMC_II
config EEXPRESS
tristate "EtherExpress 16 support"
- depends on NET_ISA
+ depends on ISA
---help---
If you have an EtherExpress16 network (Ethernet) card, say Y and
read the Ethernet-HOWTO, available from
@@ -249,7 +249,7 @@ config EEXPRESS
config EEXPRESS_PRO
tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
- depends on NET_ISA
+ depends on ISA
---help---
If you have a network (Ethernet) card of this type, say Y. This
driver supports Intel i82595{FX,TX} based boards. Note however
@@ -262,7 +262,7 @@ config EEXPRESS_PRO
config LP486E
tristate "LP486E on board Ethernet"
- depends on NET_ISA
+ depends on ISA
help
Say Y here to support the 82596-based on-board Ethernet controller
for the Panther motherboard, which is one of the two shipped in the
@@ -270,7 +270,7 @@ config LP486E
config ZNET
tristate "Zenith Z-Note support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
+ depends on ISA && EXPERIMENTAL && ISA_DMA_API
help
The Zenith Z-Note notebook computer has a built-in network
(Ethernet) card, and this is the Linux driver for it. Note that the
@@ -501,7 +501,7 @@ config ULTRA32
config E2100
tristate "Cabletron E21xx support"
- depends on NET_ISA
+ depends on ISA
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
@@ -513,7 +513,7 @@ config E2100
config HPLAN_PLUS
tristate "HP PCLAN+ (27247B and 27252A) support"
- depends on NET_ISA
+ depends on ISA
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
@@ -525,7 +525,7 @@ config HPLAN_PLUS
config HPLAN
tristate "HP PCLAN (27245 and other 27xxx series) support"
- depends on NET_ISA
+ depends on ISA
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
@@ -537,7 +537,7 @@ config HPLAN
config NE2000
tristate "NE2000/NE1000 support"
- depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
+ depends on ISA || (Q40 && m) || M32R || MACH_TX49XX
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
@@ -600,7 +600,7 @@ config AT1700
config ETH16I
tristate "ICL EtherTeam 16i/32 support"
- depends on NET_ISA
+ depends on ISA
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
@@ -611,7 +611,7 @@ config ETH16I
config SEEQ8005
tristate "SEEQ8005 support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL
+ depends on ISA && EXPERIMENTAL
help
This is a driver for the SEEQ 8005 network (Ethernet) card. If this
is for you, read the Ethernet-HOWTO, available from
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 14/15] MAINTAINERS: updates for new drivers/net/legacy dir
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (12 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 13/15] netdev: kill off NET_ISA Kconfig option Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:19 ` [PATCH 15/15] netdev: relocate LICENSE.SRC to legacy Paul Gortmaker
` (2 subsequent siblings)
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
Some drivers, particularly those which are greater than 10 years
old, have been moved off to a new legacy directory. Update the
MAINTAINERS file to indicate this new path.
For the 8390 based drivers, change the status from maintained to
obsolete and remove the old e-mail address.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
MAINTAINERS | 19 +++++++++----------
1 files changed, 9 insertions(+), 10 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index 69aa8fe..5d499d1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -116,7 +116,7 @@ Maintainers List (try to look for most precise areas first)
M: Philip Blundell <philb@gnu.org>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/3c505*
+F: drivers/net/legacy/3c505*
3C59X NETWORK DRIVER
M: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
@@ -166,11 +166,10 @@ F: drivers/serial/8250*
F: include/linux/serial_8250.h
8390 NETWORK DRIVERS [WD80x3/SMC-ELITE, SMC-ULTRA, NE2000, 3C503, etc.]
-M: Paul Gortmaker <p_gortmaker@yahoo.com>
L: netdev@vger.kernel.org
-S: Maintained
-F: drivers/net/*8390*
-F: drivers/net/ax88796.c
+S: Obsolete
+F: drivers/net/legacy/*8390*
+F: drivers/net/legacy/ax88796.c
9P FILE SYSTEM
M: Eric Van Hensbergen <ericvh@gmail.com>
@@ -1945,7 +1944,7 @@ F: net/decnet/
DEFXX FDDI NETWORK DRIVER
M: "Maciej W. Rozycki" <macro@linux-mips.org>
S: Maintained
-F: drivers/net/defxx.*
+F: drivers/net/legacy/defxx.*
DELL LAPTOP DRIVER
M: Matthew Garrett <mjg59@srcf.ucam.org>
@@ -2326,7 +2325,7 @@ ETHEREXPRESS-16 NETWORK DRIVER
M: Philip Blundell <philb@gnu.org>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/eexpress.*
+F: drivers/net/legacy/eexpress.*
ETHERNET BRIDGE
M: Stephen Hemminger <shemminger@linux-foundation.org>
@@ -2340,7 +2339,7 @@ F: net/bridge/
ETHERTEAM 16I DRIVER
M: Mika Kuoppala <miku@iki.fi>
S: Maintained
-F: drivers/net/eth16i.c
+F: drivers/net/legacy/eth16i.c
EXT2 FILE SYSTEM
M: Jan Kara <jack@suse.cz>
@@ -4232,7 +4231,7 @@ M: Jan-Pascal van Best <janpascal@vanbest.org>
M: Andreas Mohr <andi@lisas.de>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/ni5010.*
+F: drivers/net/legacy/ni5010.*
NILFS2 FILESYSTEM
M: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
@@ -5975,7 +5974,7 @@ W: http://uclinux-h8.sourceforge.jp/
S: Supported
F: arch/h8300/
F: drivers/ide/ide-h8300.c
-F: drivers/net/ne-h8300.c
+F: drivers/net/legacy/ne-h8300.c
UDF FILESYSTEM
M: Jan Kara <jack@suse.cz>
--
1.7.3.2.146.g2d444
^ permalink raw reply related [flat|nested] 38+ messages in thread
* [PATCH 15/15] netdev: relocate LICENSE.SRC to legacy
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (13 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 14/15] MAINTAINERS: updates for new drivers/net/legacy dir Paul Gortmaker
@ 2010-10-29 1:19 ` Paul Gortmaker
2010-10-29 1:48 ` [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Joe Perches
[not found] ` <alpine.LNX.2.01.1012161253560.3000@obet.zrqbmnf.qr>
16 siblings, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 1:19 UTC (permalink / raw)
To: davem; +Cc: netdev
A grep for "..GNU General Public License as modified by SRC.." shows
that this license file only applies to some of the earliest
drivers added ~15 years ago. Since all these drivers are now in the
legacy dir, the license might as well be too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
drivers/net/{ => legacy}/LICENSE.SRC | 0
1 files changed, 0 insertions(+), 0 deletions(-)
rename drivers/net/{ => legacy}/LICENSE.SRC (100%)
diff --git a/drivers/net/LICENSE.SRC b/drivers/net/legacy/LICENSE.SRC
similarity index 100%
rename from drivers/net/LICENSE.SRC
rename to drivers/net/legacy/LICENSE.SRC
--
1.7.3.2.146.g2d444
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
` (14 preceding siblings ...)
2010-10-29 1:19 ` [PATCH 15/15] netdev: relocate LICENSE.SRC to legacy Paul Gortmaker
@ 2010-10-29 1:48 ` Joe Perches
2010-10-29 9:40 ` David Lamparter
2010-10-29 21:26 ` Paul Gortmaker
[not found] ` <alpine.LNX.2.01.1012161253560.3000@obet.zrqbmnf.qr>
16 siblings, 2 replies; 38+ messages in thread
From: Joe Perches @ 2010-10-29 1:48 UTC (permalink / raw)
To: Paul Gortmaker; +Cc: davem, netdev, Jeff Kirsher
On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
> The drivers/net dir has a lot of files - originally there were
> no subdirs, but at least now subdirs are being used effectively.
> But the original drivers from 10+ years ago are still right
> there at the top. This series creates a drivers/net/legacy dir.
Hi Paul.
I like this idea.
I suggest a bit of a further grouping by using a
drivers/net/ethernet directory and putting those
legacy drivers in a new subdirectory
drivers/net/ethernet/legacy.
> The initial target is things like ISA/EISA/MCA drivers, and with
> that alone, we can get close to 90 files out of drivers/net.
> Plus, by having a semi-defined description for legacy as being
> "drivers more than 10 years old" we'll always have a destination
> for drivers as they fall out of maintainership and use.
I think legacy is "old and not sold or used much anymore".
I believe you're not moving 3c59x as that's relatively
still popular even though it's nearly 15 years old.
Or maybe that was just an oversight...
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 1:19 ` [PATCH 05/15] dec netdev: relocate DIGITAL based " Paul Gortmaker
@ 2010-10-29 4:21 ` Maciej W. Rozycki
2010-10-29 4:29 ` David Miller
0 siblings, 1 reply; 38+ messages in thread
From: Maciej W. Rozycki @ 2010-10-29 4:21 UTC (permalink / raw)
To: Paul Gortmaker; +Cc: davem, netdev
On Thu, 28 Oct 2010, Paul Gortmaker wrote:
> DEC as a name brand has been gone for over 10 years, and these
> drivers represent technology from the 1990's like the venerable
> ISA bus. Hence relocate them to the legacy dir.
NAK for the TURBOchannel bits (defxx.[ch] and declance.c) unless you give
a plausible justification. You won't get these drivers offered unless you
have the bus in your system anyway, and if you do than you don't want to
have them hidden somewhere in the corner. If you see anything wrong with
these drivers, then please do let me know.
Also defxx.c is PCI too (apart from being EISA and TC).
> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
> ---
> drivers/net/Kconfig | 63 -----------------------------------
> drivers/net/Makefile | 4 --
> drivers/net/legacy/Kconfig | 63 +++++++++++++++++++++++++++++++++++
> drivers/net/legacy/Makefile | 5 +++
> drivers/net/{ => legacy}/declance.c | 0
> drivers/net/{ => legacy}/defxx.c | 0
> drivers/net/{ => legacy}/defxx.h | 0
> drivers/net/{ => legacy}/depca.c | 0
> drivers/net/{ => legacy}/depca.h | 0
> drivers/net/{ => legacy}/ewrk3.c | 0
> drivers/net/{ => legacy}/ewrk3.h | 0
Maciej
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 4:21 ` Maciej W. Rozycki
@ 2010-10-29 4:29 ` David Miller
2010-10-29 4:54 ` Maciej W. Rozycki
0 siblings, 1 reply; 38+ messages in thread
From: David Miller @ 2010-10-29 4:29 UTC (permalink / raw)
To: macro; +Cc: paul.gortmaker, netdev
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Date: Fri, 29 Oct 2010 05:21:35 +0100 (BST)
> On Thu, 28 Oct 2010, Paul Gortmaker wrote:
>
>> DEC as a name brand has been gone for over 10 years, and these
>> drivers represent technology from the 1990's like the venerable
>> ISA bus. Hence relocate them to the legacy dir.
>
> NAK for the TURBOchannel bits (defxx.[ch] and declance.c) unless you give
> a plausible justification. You won't get these drivers offered unless you
> have the bus in your system anyway, and if you do than you don't want to
> have them hidden somewhere in the corner. If you see anything wrong with
> these drivers, then please do let me know.
>
> Also defxx.c is PCI too (apart from being EISA and TC).
PCI things can be legacy too.
This is not about a specific bus technology, it's simply for
"really old stuff" so we can declutter the top-level of drivers/net
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 4:29 ` David Miller
@ 2010-10-29 4:54 ` Maciej W. Rozycki
2010-10-29 5:46 ` Maciej W. Rozycki
2010-10-29 5:47 ` David Miller
0 siblings, 2 replies; 38+ messages in thread
From: Maciej W. Rozycki @ 2010-10-29 4:54 UTC (permalink / raw)
To: David Miller; +Cc: paul.gortmaker, netdev
On Thu, 28 Oct 2010, David Miller wrote:
> > NAK for the TURBOchannel bits (defxx.[ch] and declance.c) unless you give
> > a plausible justification. You won't get these drivers offered unless you
> > have the bus in your system anyway, and if you do than you don't want to
> > have them hidden somewhere in the corner. If you see anything wrong with
> > these drivers, then please do let me know.
> >
> > Also defxx.c is PCI too (apart from being EISA and TC).
>
> PCI things can be legacy too.
>
> This is not about a specific bus technology, it's simply for
> "really old stuff" so we can declutter the top-level of drivers/net
Hmm, what's the difference between placing these drivers here or there
and what's so particular about them that they cause clutter? I mean a
mere high number of items does not cause a mess by itself -- the lack of
order might.
Also -- if this change goes ahead -- when I add new TURBOchannel drivers,
should they go straight to legacy/? It sounds odd to me to have a thing
obsolete straight from the beginning.
Maciej
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 4:54 ` Maciej W. Rozycki
@ 2010-10-29 5:46 ` Maciej W. Rozycki
2010-10-29 5:53 ` David Miller
2010-10-29 5:47 ` David Miller
1 sibling, 1 reply; 38+ messages in thread
From: Maciej W. Rozycki @ 2010-10-29 5:46 UTC (permalink / raw)
To: David Miller; +Cc: paul.gortmaker, netdev
On Fri, 29 Oct 2010, Maciej W. Rozycki wrote:
> > This is not about a specific bus technology, it's simply for
> > "really old stuff" so we can declutter the top-level of drivers/net
>
> Hmm, what's the difference between placing these drivers here or there
> and what's so particular about them that they cause clutter? I mean a
> mere high number of items does not cause a mess by itself -- the lack of
> order might.
I have given myself some food for thought and have come up with the
following proposal: how about simply classifying drivers according to the
physical layer they support or if multiple are, such as with the Ethernet
that is backwards compatible, the newest variation they do?
This would be no different to what we do wrt network protocols under
net/, so drivers would go to ethernet/, fasteth/, gbeth/, 10gbeth/, fddi/,
tokenring/, atm/, appletalk/, etc. (names up to debate if need be) as
applicable. This would scale well, avoid the need for arbitrary decisions
(is this piece legacy yet or not?) and automatically classify drivers as
more or less obsolescent too, as obviously none of the stuff under
ethernet/, fddi/ or tokenring/ can be reasonably recent unlike 10gbeth/.
Software stuff such as SLIP or PPP could go either into separate
subdirectories or grouped together under software/; I gather we have a few
such pieces only.
What do you think?
Maciej
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 4:54 ` Maciej W. Rozycki
2010-10-29 5:46 ` Maciej W. Rozycki
@ 2010-10-29 5:47 ` David Miller
2010-10-29 5:50 ` Maciej W. Rozycki
1 sibling, 1 reply; 38+ messages in thread
From: David Miller @ 2010-10-29 5:47 UTC (permalink / raw)
To: macro; +Cc: paul.gortmaker, netdev
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Date: Fri, 29 Oct 2010 05:54:56 +0100 (BST)
> Hmm, what's the difference between placing these drivers here or there
> and what's so particular about them that they cause clutter? I mean a
> mere high number of items does not cause a mess by itself -- the lack of
> order might.
>
> Also -- if this change goes ahead -- when I add new TURBOchannel drivers,
> should they go straight to legacy/? It sounds odd to me to have a thing
> obsolete straight from the beginning.
This patch series started with a "0/15" introduction posting which
explains the intention and reasoning.
It might be easier for you to read it instead of asking me to repeat
it's contents :-)
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 5:47 ` David Miller
@ 2010-10-29 5:50 ` Maciej W. Rozycki
2010-10-29 5:53 ` David Miller
0 siblings, 1 reply; 38+ messages in thread
From: Maciej W. Rozycki @ 2010-10-29 5:50 UTC (permalink / raw)
To: David Miller; +Cc: paul.gortmaker, netdev
On Thu, 28 Oct 2010, David Miller wrote:
> This patch series started with a "0/15" introduction posting which
> explains the intention and reasoning.
Well, I didn't reach it (ENOBREAKFAST that has been fixed since ;) ), but
I sort of guessed it anyway and didn't like the arbitrary nature of
assigning drivers to legacy/.
> It might be easier for you to read it instead of asking me to repeat
> it's contents :-)
See my proposal that crossed with your e-mail. I think it fits the
purpose very well. :)
Maciej
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 5:46 ` Maciej W. Rozycki
@ 2010-10-29 5:53 ` David Miller
0 siblings, 0 replies; 38+ messages in thread
From: David Miller @ 2010-10-29 5:53 UTC (permalink / raw)
To: macro; +Cc: paul.gortmaker, netdev
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Date: Fri, 29 Oct 2010 06:46:13 +0100 (BST)
> This would be no different to what we do wrt network protocols under
> net/, so drivers would go to ethernet/, fasteth/, gbeth/, 10gbeth/, fddi/,
> tokenring/, atm/, appletalk/, etc. (names up to debate if need be) as
> applicable. This would scale well, avoid the need for arbitrary decisions
> (is this piece legacy yet or not?) and automatically classify drivers as
> more or less obsolescent too, as obviously none of the stuff under
> ethernet/, fddi/ or tokenring/ can be reasonably recent unlike 10gbeth/.
Why are you so hung up about something being called legacy?
I would be proud to be labelled "legacy", as that means I've served a
purpose for a long time and some folks even want or need me to stick
around for a bit longer.
Legacy hardware is just old and the drivers for them are in a purely
"sustaining" state, that is all.
And using link layer technology to classify is really stupid since
many devices match multiple of the categories you've suggested.
I think the existing proposal is just fine.
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 5:50 ` Maciej W. Rozycki
@ 2010-10-29 5:53 ` David Miller
2010-10-29 6:37 ` Maciej W. Rozycki
0 siblings, 1 reply; 38+ messages in thread
From: David Miller @ 2010-10-29 5:53 UTC (permalink / raw)
To: macro; +Cc: paul.gortmaker, netdev
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Date: Fri, 29 Oct 2010 06:50:17 +0100 (BST)
> On Thu, 28 Oct 2010, David Miller wrote:
>
>> It might be easier for you to read it instead of asking me to repeat
>> it's contents :-)
>
> See my proposal that crossed with your e-mail. I think it fits the
> purpose very well. :)
No, it's foolish, see my reply.
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 05/15] dec netdev: relocate DIGITAL based drivers to legacy
2010-10-29 5:53 ` David Miller
@ 2010-10-29 6:37 ` Maciej W. Rozycki
0 siblings, 0 replies; 38+ messages in thread
From: Maciej W. Rozycki @ 2010-10-29 6:37 UTC (permalink / raw)
To: David Miller; +Cc: paul.gortmaker, netdev
On Thu, 28 Oct 2010, David Miller wrote:
> > See my proposal that crossed with your e-mail. I think it fits the
> > purpose very well. :)
>
> No, it's foolish, see my reply.
Well, you are the maintainer, so it's your call. I disagree and I have
given what I believe is a reasonable justification, but that's about as
much as I can do -- I can't force it onto you. As I say my concern is
about the arbitrary assignment and not things being called "legacy" or
"best-ever", "pre-y2k", or whatever. And splitting a bunch of pieces of
software that are loosely related to one another into two bunches isn't
going to reduce clutter, but to spread it instead -- now you'll have
clutter in two places rather than just one, so I think the change is just
missing the point. Again, as the maintainer it's your right to disagree.
Thank you for the time you've taken to consider my comments nonetheless.
Maciej
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-29 1:48 ` [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Joe Perches
@ 2010-10-29 9:40 ` David Lamparter
2010-10-29 10:13 ` Maciej W. Rozycki
2010-10-29 21:26 ` Paul Gortmaker
1 sibling, 1 reply; 38+ messages in thread
From: David Lamparter @ 2010-10-29 9:40 UTC (permalink / raw)
To: Joe Perches; +Cc: netdev
On Thu, Oct 28, 2010 at 06:48:16PM -0700, Joe Perches wrote:
> On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
> > The initial target is things like ISA/EISA/MCA drivers, and with
> > that alone, we can get close to 90 files out of drivers/net.
> > Plus, by having a semi-defined description for legacy as being
> > "drivers more than 10 years old" we'll always have a destination
> > for drivers as they fall out of maintainership and use.
>
> I think legacy is "old and not sold or used much anymore".
>
> I believe you're not moving 3c59x as that's relatively
> still popular even though it's nearly 15 years old.
>
> Or maybe that was just an oversight...
The 3c59x driver also drives a few not-that-old 100MBit cards like
"3Com Corporation 3c905B 100BaseTX [Cyclone] [10b7:9055] (rev 64)"
and these are quite common still :)
-David
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-29 9:40 ` David Lamparter
@ 2010-10-29 10:13 ` Maciej W. Rozycki
0 siblings, 0 replies; 38+ messages in thread
From: Maciej W. Rozycki @ 2010-10-29 10:13 UTC (permalink / raw)
To: David Lamparter; +Cc: Joe Perches, netdev
On Fri, 29 Oct 2010, David Lamparter wrote:
> > > The initial target is things like ISA/EISA/MCA drivers, and with
> > > that alone, we can get close to 90 files out of drivers/net.
> > > Plus, by having a semi-defined description for legacy as being
> > > "drivers more than 10 years old" we'll always have a destination
> > > for drivers as they fall out of maintainership and use.
> >
> > I think legacy is "old and not sold or used much anymore".
> >
> > I believe you're not moving 3c59x as that's relatively
> > still popular even though it's nearly 15 years old.
> >
> > Or maybe that was just an oversight...
>
> The 3c59x driver also drives a few not-that-old 100MBit cards like
> "3Com Corporation 3c905B 100BaseTX [Cyclone] [10b7:9055] (rev 64)"
> and these are quite common still :)
What's the difference? -- that's a change of the name only you should be
proud of! ;)
I have seen plenty of these Vortex/Boomerang/Cyclone cards in various
configurations and still have a couple myself, but I fail to recall any
that would be less than 8 years old, which is about the age of my newest
FDDI stuff (updated by the manufacturer to universal PCI and HP-branded
because of the DEC/Compaq acquisition) which has been declared "obviously
obsolete", so why shouldn't this equipment be either? ;)
Maciej
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-29 1:48 ` [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Joe Perches
2010-10-29 9:40 ` David Lamparter
@ 2010-10-29 21:26 ` Paul Gortmaker
2010-10-29 22:08 ` Joe Perches
1 sibling, 1 reply; 38+ messages in thread
From: Paul Gortmaker @ 2010-10-29 21:26 UTC (permalink / raw)
To: Joe Perches; +Cc: davem, netdev, Jeff Kirsher
On 10-10-28 09:48 PM, Joe Perches wrote:
> On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
>> The drivers/net dir has a lot of files - originally there were
>> no subdirs, but at least now subdirs are being used effectively.
>> But the original drivers from 10+ years ago are still right
>> there at the top. This series creates a drivers/net/legacy dir.
>
> Hi Paul.
>
> I like this idea.
>
> I suggest a bit of a further grouping by using a
> drivers/net/ethernet directory and putting those
> legacy drivers in a new subdirectory
> drivers/net/ethernet/legacy.
That is a substantially larger change, since you'd now be
relocating nearly every remaining driver, i.e. all the
relatively modern 100M and GigE drivers. Plus what do you
do with the sb1000 - create drivers/cablemodem/legacy
just for one file? Or the ethernet drivers already in
existing subdirs, like arm and pcmcia -- do we move those?
With this, I tried to aim for a significant gain (close to 1/3
less files) within what I felt was a reasonable sized change
set that had a chance of getting an overall OK from folks.
Giant "flag-day" type mammoth changesets are a PITA for all.
>
>> The initial target is things like ISA/EISA/MCA drivers, and with
>> that alone, we can get close to 90 files out of drivers/net.
>> Plus, by having a semi-defined description for legacy as being
>> "drivers more than 10 years old" we'll always have a destination
>> for drivers as they fall out of maintainership and use.
>
> I think legacy is "old and not sold or used much anymore".
I tried to stick to having both, ie. old + not used much,
in what I chose for my initial group. Where "old" is
meant to apply to the hardware, and not to the driver.
>
> I believe you're not moving 3c59x as that's relatively
> still popular even though it's nearly 15 years old.
>
> Or maybe that was just an oversight...
I didn't want to include any drivers in the initial group
that I thought might sidetrack the issue by being contentious
(clearly I was off by one) -- the point being, that once the
base infrastructure and initial group of (almost) universally
agreed upon ones is in, more can be discussed and added later,
as appropriate.
Paul.
>
>
>
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-29 21:26 ` Paul Gortmaker
@ 2010-10-29 22:08 ` Joe Perches
2010-10-30 0:01 ` Jeff Kirsher
0 siblings, 1 reply; 38+ messages in thread
From: Joe Perches @ 2010-10-29 22:08 UTC (permalink / raw)
To: Paul Gortmaker; +Cc: davem, netdev, Jeff Kirsher
On Fri, 2010-10-29 at 17:26 -0400, Paul Gortmaker wrote:
> On 10-10-28 09:48 PM, Joe Perches wrote:
> > On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
> >> The drivers/net dir has a lot of files - originally there were
> >> no subdirs, but at least now subdirs are being used effectively.
> >> But the original drivers from 10+ years ago are still right
> >> there at the top. This series creates a drivers/net/legacy dir.
> > I like this idea.
> > I suggest a bit of a further grouping by using a
> > drivers/net/ethernet directory and putting those
> > legacy drivers in a new subdirectory
> > drivers/net/ethernet/legacy.
> That is a substantially larger change, since you'd now be
> relocating nearly every remaining driver, i.e. all the
> relatively modern 100M and GigE drivers.
Files to not need immediate renames.
Renames could happen when the appropriate maintainer
wants to or gets coerced to conform to some new
file layout standard.
I had submitted a related RFC patch:
https://patchwork.kernel.org/patch/244641/
and then had some off list discussions
with Jeff Kirsher from Intel.
Perhaps Jeff will chime in.
> Plus what do you
> do with the sb1000 - create drivers/cablemodem/legacy
> just for one file?
I never looked at that particular driver before.
Maybe. I don't have a strong opinion. Leaving
it where it is might be OK.
> Or the ethernet drivers already in
> existing subdirs, like arm and pcmcia -- do we move those?
Maybe. If there's no demand, there's no absolute need to
move it at all. I think a reasonable goal is to have some
sensible and consistent file layout scheme though.
There are arch specific directories under various drivers/...
so I don't see a need to move directories like drivers/net/arm
or drivers/s390.
> With this, I tried to aim for a significant gain (close to 1/3
> less files) within what I felt was a reasonable sized change
> set that had a chance of getting an overall OK from folks.
> Giant "flag-day" type mammoth changesets are a PITA for all.
I believe there's no need for a flag-day.
File renames could happen gradually or not at all.
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-29 22:08 ` Joe Perches
@ 2010-10-30 0:01 ` Jeff Kirsher
2010-11-04 21:20 ` Paul Gortmaker
0 siblings, 1 reply; 38+ messages in thread
From: Jeff Kirsher @ 2010-10-30 0:01 UTC (permalink / raw)
To: Joe Perches; +Cc: Paul Gortmaker, davem, netdev
[-- Attachment #1: Type: text/plain, Size: 2891 bytes --]
On Fri, 2010-10-29 at 15:08 -0700, Joe Perches wrote:
> On Fri, 2010-10-29 at 17:26 -0400, Paul Gortmaker wrote:
> > On 10-10-28 09:48 PM, Joe Perches wrote:
> > > On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
> > >> The drivers/net dir has a lot of files - originally there were
> > >> no subdirs, but at least now subdirs are being used effectively.
> > >> But the original drivers from 10+ years ago are still right
> > >> there at the top. This series creates a drivers/net/legacy dir.
> > > I like this idea.
> > > I suggest a bit of a further grouping by using a
> > > drivers/net/ethernet directory and putting those
> > > legacy drivers in a new subdirectory
> > > drivers/net/ethernet/legacy.
> > That is a substantially larger change, since you'd now be
> > relocating nearly every remaining driver, i.e. all the
> > relatively modern 100M and GigE drivers.
>
I am not particularly a fan of making a "legacy" directory and moving
old drivers into it. Just because this is very subjective, if you say
"drivers which are X years old and not used much" is vague and depending
on who you ask would get varying results. But if you were to were to
define legacy as all ISA, EISA and MCA drivers (not based on their use)
would be better.
But if a legacy directory was to be made, I like Joe's suggestion of
drivers/net/ethernet/legacy.
> Files to not need immediate renames.
>
> Renames could happen when the appropriate maintainer
> wants to or gets coerced to conform to some new
> file layout standard.
>
> I had submitted a related RFC patch:
>
> https://patchwork.kernel.org/patch/244641/
>
> and then had some off list discussions
> with Jeff Kirsher from Intel.
>
> Perhaps Jeff will chime in.
>
> > Plus what do you
> > do with the sb1000 - create drivers/cablemodem/legacy
> > just for one file?
>
> I never looked at that particular driver before.
> Maybe. I don't have a strong opinion. Leaving
> it where it is might be OK.
>
> > Or the ethernet drivers already in
> > existing subdirs, like arm and pcmcia -- do we move those?
>
> Maybe. If there's no demand, there's no absolute need to
> move it at all. I think a reasonable goal is to have some
> sensible and consistent file layout scheme though.
>
> There are arch specific directories under various drivers/...
> so I don't see a need to move directories like drivers/net/arm
> or drivers/s390.
I agree with Joe.
>
> > With this, I tried to aim for a significant gain (close to 1/3
> > less files) within what I felt was a reasonable sized change
> > set that had a chance of getting an overall OK from folks.
> > Giant "flag-day" type mammoth changesets are a PITA for all.
>
> I believe there's no need for a flag-day.
> File renames could happen gradually or not at all.
>
>
Again I agree with Joe.
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-10-30 0:01 ` Jeff Kirsher
@ 2010-11-04 21:20 ` Paul Gortmaker
2010-11-05 2:28 ` Jeff Kirsher
0 siblings, 1 reply; 38+ messages in thread
From: Paul Gortmaker @ 2010-11-04 21:20 UTC (permalink / raw)
To: jeffrey.t.kirsher; +Cc: Joe Perches, davem, netdev
On 10-10-29 08:01 PM, Jeff Kirsher wrote:
> On Fri, 2010-10-29 at 15:08 -0700, Joe Perches wrote:
>> On Fri, 2010-10-29 at 17:26 -0400, Paul Gortmaker wrote:
>>> On 10-10-28 09:48 PM, Joe Perches wrote:
>>>> On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
>>>>> The drivers/net dir has a lot of files - originally there were
>>>>> no subdirs, but at least now subdirs are being used effectively.
>>>>> But the original drivers from 10+ years ago are still right
>>>>> there at the top. This series creates a drivers/net/legacy dir.
>>>> I like this idea.
>>>> I suggest a bit of a further grouping by using a
>>>> drivers/net/ethernet directory and putting those
>>>> legacy drivers in a new subdirectory
>>>> drivers/net/ethernet/legacy.
>>> That is a substantially larger change, since you'd now be
>>> relocating nearly every remaining driver, i.e. all the
>>> relatively modern 100M and GigE drivers.
>>
>
> I am not particularly a fan of making a "legacy" directory and moving
> old drivers into it. Just because this is very subjective, if you say
> "drivers which are X years old and not used much" is vague and depending
> on who you ask would get varying results. But if you were to were to
> define legacy as all ISA, EISA and MCA drivers (not based on their use)
> would be better.
I think that being subjective can be an advantage. There may
be some debate on whether X is legacy or not, but I see no harm
in that. On the other hand, I see binding ourselves to concrete
inflexible rules as a disadvantage.
For example, look at the sister directory, drivers/serial -- the
venerable 8250 UART continues to support ISA-like mapped 0x3f8/0x2f8
PIO devices such as those on the ISA MultiIO/IDE cards first appearing
in 80286 computers. But we probably don't want to shuffle that off to
a legacy dir, given that nearly every embedded CPU manufacturer has a
SoC 8250 UART implementation of their own, and it remains in high use.
>
> But if a legacy directory was to be made, I like Joe's suggestion of
> drivers/net/ethernet/legacy.
If we extend that to being a rule, i.e. drivers/net/*/legacy
then we'd implicitly be advocating creation of things like:
drivers/net/tokenring/legacy
drivers/net/arcnet/legacy
Yes, I do imagine you aren't suggesting we do that. :)
>
>> Files to not need immediate renames.
>>
>> Renames could happen when the appropriate maintainer
>> wants to or gets coerced to conform to some new
>> file layout standard.
>>
>> I had submitted a related RFC patch:
>>
>> https://patchwork.kernel.org/patch/244641/
>>
>> and then had some off list discussions
>> with Jeff Kirsher from Intel.
>>
>> Perhaps Jeff will chime in.
>>
>>> Plus what do you
>>> do with the sb1000 - create drivers/cablemodem/legacy
>>> just for one file?
>>
>> I never looked at that particular driver before.
>> Maybe. I don't have a strong opinion. Leaving
>> it where it is might be OK.
>>
>>> Or the ethernet drivers already in
>>> existing subdirs, like arm and pcmcia -- do we move those?
>>
>> Maybe. If there's no demand, there's no absolute need to
>> move it at all. I think a reasonable goal is to have some
>> sensible and consistent file layout scheme though.
>>
>> There are arch specific directories under various drivers/...
>> so I don't see a need to move directories like drivers/net/arm
>> or drivers/s390.
>
> I agree with Joe.
I don't think there is any disagreement here on this point.
Moving stuff that is already in an appropriate subdir was
never part of what I was proposing with drivers/legacy.
But if we create subdirs with concrete definitions, then
people will most likely be expecting all drivers that match
to be in that specific subdir.
>
>>
>>> With this, I tried to aim for a significant gain (close to 1/3
>>> less files) within what I felt was a reasonable sized change
>>> set that had a chance of getting an overall OK from folks.
>>> Giant "flag-day" type mammoth changesets are a PITA for all.
>>
>> I believe there's no need for a flag-day.
>> File renames could happen gradually or not at all.
>>
>>
>
> Again I agree with Joe.
Sure, renames can be async, and driven by the individual
maintainers of the files, but typically when conversion
like events are left open ended (timewise) they tend
to drag on for longer times than necessary. At least in
my experience. If I had sent the RFC with one patch that
amounted to a "mkdir", and no actual file moves, I wouldn't
have expected much other than a bagful of scorn in return. :)
Putting it to use and showing a real cleanup is where the
value became really apparent, I think.
In any case, I still think this is worthwhile, and in the
absence of an alternate proposal that gets a higher level
of universal agreement, I'm hoping we can still do this.
I've got a follow on commit ready that factors a lot of
the legacy related probe code out of Space.c too.
Regardless of which way it goes, thanks for the feedback.
Paul.
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-11-04 21:20 ` Paul Gortmaker
@ 2010-11-05 2:28 ` Jeff Kirsher
2010-11-05 12:51 ` Paul Gortmaker
2010-11-18 23:52 ` Joe Perches
0 siblings, 2 replies; 38+ messages in thread
From: Jeff Kirsher @ 2010-11-05 2:28 UTC (permalink / raw)
To: Paul Gortmaker; +Cc: Joe Perches, davem, netdev
On Thu, Nov 4, 2010 at 14:20, Paul Gortmaker
<paul.gortmaker@windriver.com> wrote:
> On 10-10-29 08:01 PM, Jeff Kirsher wrote:
>> On Fri, 2010-10-29 at 15:08 -0700, Joe Perches wrote:
>>> On Fri, 2010-10-29 at 17:26 -0400, Paul Gortmaker wrote:
>>>> On 10-10-28 09:48 PM, Joe Perches wrote:
>>>>> On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
>>>>>> The drivers/net dir has a lot of files - originally there were
>>>>>> no subdirs, but at least now subdirs are being used effectively.
>>>>>> But the original drivers from 10+ years ago are still right
>>>>>> there at the top. This series creates a drivers/net/legacy dir.
>>>>> I like this idea.
>>>>> I suggest a bit of a further grouping by using a
>>>>> drivers/net/ethernet directory and putting those
>>>>> legacy drivers in a new subdirectory
>>>>> drivers/net/ethernet/legacy.
>>>> That is a substantially larger change, since you'd now be
>>>> relocating nearly every remaining driver, i.e. all the
>>>> relatively modern 100M and GigE drivers.
>>>
>>
>> I am not particularly a fan of making a "legacy" directory and moving
>> old drivers into it. Just because this is very subjective, if you say
>> "drivers which are X years old and not used much" is vague and depending
>> on who you ask would get varying results. But if you were to were to
>> define legacy as all ISA, EISA and MCA drivers (not based on their use)
>> would be better.
>
> I think that being subjective can be an advantage. There may
> be some debate on whether X is legacy or not, but I see no harm
> in that. On the other hand, I see binding ourselves to concrete
> inflexible rules as a disadvantage.
>
I am not disagreeing that we need to be flexible, and to organize the
directory structure in a logical way does not equate to "concrete and
inflexible".
I brought the topic of organizing the /drivers/net directory up at
NetConf/Plumbers and here is what came about the discussion...
Joe and I are working to organize the drivers into
/drivers/net/<technology> directories and to cleanup the Kconfig to
reflect the organization. Ethernet drivers will be in
/drivers/net/ethernet, and so on. I brought up your suggestion to
making a "legacy" directory and those present did not like the idea.
In short, there is no advantage to this type of organization and
having the drivers reside in their current location or in the model of
/drivers/net/<technology> does not cause any problems
> For example, look at the sister directory, drivers/serial -- the
> venerable 8250 UART continues to support ISA-like mapped 0x3f8/0x2f8
> PIO devices such as those on the ISA MultiIO/IDE cards first appearing
> in 80286 computers. But we probably don't want to shuffle that off to
> a legacy dir, given that nearly every embedded CPU manufacturer has a
> SoC 8250 UART implementation of their own, and it remains in high use.
>
>>
>> But if a legacy directory was to be made, I like Joe's suggestion of
>> drivers/net/ethernet/legacy.
>
> If we extend that to being a rule, i.e. drivers/net/*/legacy
> then we'd implicitly be advocating creation of things like:
>
> drivers/net/tokenring/legacy
> drivers/net/arcnet/legacy
>
> Yes, I do imagine you aren't suggesting we do that. :)
>
>>
>>> Files to not need immediate renames.
>>>
>>> Renames could happen when the appropriate maintainer
>>> wants to or gets coerced to conform to some new
>>> file layout standard.
>>>
>>> I had submitted a related RFC patch:
>>>
>>> https://patchwork.kernel.org/patch/244641/
>>>
>>> and then had some off list discussions
>>> with Jeff Kirsher from Intel.
>>>
>>> Perhaps Jeff will chime in.
>>>
>>>> Plus what do you
>>>> do with the sb1000 - create drivers/cablemodem/legacy
>>>> just for one file?
>>>
>>> I never looked at that particular driver before.
>>> Maybe. I don't have a strong opinion. Leaving
>>> it where it is might be OK.
>>>
>>>> Or the ethernet drivers already in
>>>> existing subdirs, like arm and pcmcia -- do we move those?
>>>
>>> Maybe. If there's no demand, there's no absolute need to
>>> move it at all. I think a reasonable goal is to have some
>>> sensible and consistent file layout scheme though.
>>>
>>> There are arch specific directories under various drivers/...
>>> so I don't see a need to move directories like drivers/net/arm
>>> or drivers/s390.
>>
>> I agree with Joe.
>
> I don't think there is any disagreement here on this point.
> Moving stuff that is already in an appropriate subdir was
> never part of what I was proposing with drivers/legacy.
>
> But if we create subdirs with concrete definitions, then
> people will most likely be expecting all drivers that match
> to be in that specific subdir.
Correct, although I would use "logical organization" versus "concrete
definitions" and we are working on patches to do the clean up so that
Ethernet drivers are under /drivers/net/ethernet/*, as well as the
other technologies. For the drivers like vlan, 8021q, bridging, etc
we will place those in /drivers/net/sw/. That is the plan at least...
>
>>
>>>
>>>> With this, I tried to aim for a significant gain (close to 1/3
>>>> less files) within what I felt was a reasonable sized change
>>>> set that had a chance of getting an overall OK from folks.
>>>> Giant "flag-day" type mammoth changesets are a PITA for all.
>>>
>>> I believe there's no need for a flag-day.
>>> File renames could happen gradually or not at all.
>>>
>>>
>>
>> Again I agree with Joe.
>
> Sure, renames can be async, and driven by the individual
> maintainers of the files, but typically when conversion
> like events are left open ended (timewise) they tend
> to drag on for longer times than necessary. At least in
> my experience. If I had sent the RFC with one patch that
> amounted to a "mkdir", and no actual file moves, I wouldn't
> have expected much other than a bagful of scorn in return. :)
> Putting it to use and showing a real cleanup is where the
> value became really apparent, I think.
>
We are hoping not to drag this out and plan on getting this into
2.6.38 (net-next) within the couple of weeks.
> In any case, I still think this is worthwhile, and in the
> absence of an alternate proposal that gets a higher level
> of universal agreement, I'm hoping we can still do this.
> I've got a follow on commit ready that factors a lot of
> the legacy related probe code out of Space.c too.
>
> Regardless of which way it goes, thanks for the feedback.
> Paul.
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Cheers,
Jeff
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-11-05 2:28 ` Jeff Kirsher
@ 2010-11-05 12:51 ` Paul Gortmaker
2010-11-18 23:52 ` Joe Perches
1 sibling, 0 replies; 38+ messages in thread
From: Paul Gortmaker @ 2010-11-05 12:51 UTC (permalink / raw)
To: Jeff Kirsher; +Cc: Joe Perches, davem, netdev
On 10-11-04 10:28 PM, Jeff Kirsher wrote:
> On Thu, Nov 4, 2010 at 14:20, Paul Gortmaker
> <paul.gortmaker@windriver.com> wrote:
>> On 10-10-29 08:01 PM, Jeff Kirsher wrote:
>>> On Fri, 2010-10-29 at 15:08 -0700, Joe Perches wrote:
>>>> On Fri, 2010-10-29 at 17:26 -0400, Paul Gortmaker wrote:
>>>>> On 10-10-28 09:48 PM, Joe Perches wrote:
>>>>>> On Thu, 2010-10-28 at 21:19 -0400, Paul Gortmaker wrote:
>>>>>>> The drivers/net dir has a lot of files - originally there were
>>>>>>> no subdirs, but at least now subdirs are being used effectively.
>>>>>>> But the original drivers from 10+ years ago are still right
>>>>>>> there at the top. This series creates a drivers/net/legacy dir.
>>>>>> I like this idea.
>>>>>> I suggest a bit of a further grouping by using a
>>>>>> drivers/net/ethernet directory and putting those
>>>>>> legacy drivers in a new subdirectory
>>>>>> drivers/net/ethernet/legacy.
>>>>> That is a substantially larger change, since you'd now be
>>>>> relocating nearly every remaining driver, i.e. all the
>>>>> relatively modern 100M and GigE drivers.
>>>>
>>>
>>> I am not particularly a fan of making a "legacy" directory and moving
>>> old drivers into it. Just because this is very subjective, if you say
>>> "drivers which are X years old and not used much" is vague and depending
>>> on who you ask would get varying results. But if you were to were to
>>> define legacy as all ISA, EISA and MCA drivers (not based on their use)
>>> would be better.
>>
>> I think that being subjective can be an advantage. There may
>> be some debate on whether X is legacy or not, but I see no harm
>> in that. On the other hand, I see binding ourselves to concrete
>> inflexible rules as a disadvantage.
>>
>
> I am not disagreeing that we need to be flexible, and to organize the
> directory structure in a logical way does not equate to "concrete and
> inflexible".
>
> I brought the topic of organizing the /drivers/net directory up at
> NetConf/Plumbers and here is what came about the discussion...
Thanks for the update, I wasn't aware that happened.
>
> Joe and I are working to organize the drivers into
> /drivers/net/<technology> directories and to cleanup the Kconfig to
> reflect the organization. Ethernet drivers will be in
> /drivers/net/ethernet, and so on. I brought up your suggestion to
> making a "legacy" directory and those present did not like the idea.
Interesting. I would have not came to that conclusion based on
the feedback on netdev@vger alone. Oh well, if that was the
consensus then I'm not going to argue with it.
> In short, there is no advantage to this type of organization and
> having the drivers reside in their current location or in the model of
> /drivers/net/<technology> does not cause any problems
[...]
>>>>
>>>> There are arch specific directories under various drivers/...
>>>> so I don't see a need to move directories like drivers/net/arm
>>>> or drivers/s390.
>>>
>>> I agree with Joe.
>>
>> I don't think there is any disagreement here on this point.
>> Moving stuff that is already in an appropriate subdir was
>> never part of what I was proposing with drivers/legacy.
>>
>> But if we create subdirs with concrete definitions, then
>> people will most likely be expecting all drivers that match
>> to be in that specific subdir.
>
> Correct, although I would use "logical organization" versus "concrete
> definitions" and we are working on patches to do the clean up so that
> Ethernet drivers are under /drivers/net/ethernet/*, as well as the
If you do get agreement on subcategories under ethernet for one
reason or another (i.e. vendor grouping), then I'd suggest using
ns8390 as a grouping category - it would lend itself well to
coalescing a lot of legacy drivers in itself.
> other technologies. For the drivers like vlan, 8021q, bridging, etc
> we will place those in /drivers/net/sw/. That is the plan at least...
>
>>
>>>
>>>>
>>>>> With this, I tried to aim for a significant gain (close to 1/3
>>>>> less files) within what I felt was a reasonable sized change
>>>>> set that had a chance of getting an overall OK from folks.
>>>>> Giant "flag-day" type mammoth changesets are a PITA for all.
>>>>
>>>> I believe there's no need for a flag-day.
>>>> File renames could happen gradually or not at all.
>>>>
>>>>
>>>
>>> Again I agree with Joe.
>>
>> Sure, renames can be async, and driven by the individual
>> maintainers of the files, but typically when conversion
>> like events are left open ended (timewise) they tend
>> to drag on for longer times than necessary. At least in
>> my experience. If I had sent the RFC with one patch that
>> amounted to a "mkdir", and no actual file moves, I wouldn't
>> have expected much other than a bagful of scorn in return. :)
>> Putting it to use and showing a real cleanup is where the
>> value became really apparent, I think.
>>
>
> We are hoping not to drag this out and plan on getting this into
> 2.6.38 (net-next) within the couple of weeks.
Sounds good. In the end, the one thing I was hoping to see
happen was a bit more organization in drivers/net - and both
solutions should be able to provide this.
Paul.
>
>> In any case, I still think this is worthwhile, and in the
>> absence of an alternate proposal that gets a higher level
>> of universal agreement, I'm hoping we can still do this.
>> I've got a follow on commit ready that factors a lot of
>> the legacy related probe code out of Space.c too.
>>
>> Regardless of which way it goes, thanks for the feedback.
>> Paul.
>> --
>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
>
>
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-11-05 2:28 ` Jeff Kirsher
2010-11-05 12:51 ` Paul Gortmaker
@ 2010-11-18 23:52 ` Joe Perches
2010-11-19 0:34 ` Jeff Kirsher
1 sibling, 1 reply; 38+ messages in thread
From: Joe Perches @ 2010-11-18 23:52 UTC (permalink / raw)
To: Jeff Kirsher; +Cc: Paul Gortmaker, davem, netdev
On Thu, 2010-11-04 at 19:28 -0700, Jeff Kirsher wrote:
> Joe and I are working to organize the drivers into
> /drivers/net/<technology> directories and to cleanup the Kconfig to
> reflect the organization. Ethernet drivers will be in
> /drivers/net/ethernet, and so on.
[]
> We are hoping not to drag this out and plan on getting this into
> 2.6.38 (net-next) within the couple of weeks.
What is an appropriate time frame for doing these
reorganization file/directory moves for net-next?
David, do you have a preference?
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-11-18 23:52 ` Joe Perches
@ 2010-11-19 0:34 ` Jeff Kirsher
0 siblings, 0 replies; 38+ messages in thread
From: Jeff Kirsher @ 2010-11-19 0:34 UTC (permalink / raw)
To: Joe Perches; +Cc: Paul Gortmaker, davem, netdev
[-- Attachment #1: Type: text/plain, Size: 819 bytes --]
On Thu, 2010-11-18 at 15:52 -0800, Joe Perches wrote:
> On Thu, 2010-11-04 at 19:28 -0700, Jeff Kirsher wrote:
> > Joe and I are working to organize the drivers into
> > /drivers/net/<technology> directories and to cleanup the Kconfig to
> > reflect the organization. Ethernet drivers will be in
> > /drivers/net/ethernet, and so on.
> []
> > We are hoping not to drag this out and plan on getting this into
> > 2.6.38 (net-next) within the couple of weeks.
>
> What is an appropriate time frame for doing these
> reorganization file/directory moves for net-next?
>
> David, do you have a preference?
>
I am almost ~50% done with the patch, I am hoping to get the patch out
this weekend. I have been testing as I go to ensure that there are no
breakages,that has been the reason for the delay.
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
[not found] ` <alpine.LNX.2.01.1012161253560.3000@obet.zrqbmnf.qr>
@ 2010-12-16 12:22 ` Jan Engelhardt
2010-12-17 9:51 ` Jeff Kirsher
0 siblings, 1 reply; 38+ messages in thread
From: Jan Engelhardt @ 2010-12-16 12:22 UTC (permalink / raw)
To: paul.gortmaker; +Cc: Joe Perches, Maciej W. Rozycki, Jeff Kirsher, netdev
[adding missing cc:netdev]
A few comments, since I have just been made aware of the Netconf slides,
Paul Gortmaker wrote:
>
>If in fact this series gets agreement, I'm figuring it makes sense to
>have it go in either at the beginning of a dev cycle, or at the very
>end
I think I have seen git properly coping with renames, if your and other
developers' branches are git-merged (patchwise application of course
leads to rejects).
>classifying drivers according to the physical layer they support or if
>multiple are, such as with the Ethernet that is backwards compatible,
>the newest variation they do?
Above all I would probably like to see
- getting rid of the "1000 Mbit" and "10000 Mbit" submenus. jme.ko for
example is put under 1000 Mbit, but the jme chip I have ("197b:0260 (rev
02) JMicron Technology Corp. JMC260 PCI Express Fast Ethernet
Controller") does not do 1000.
- getting rid of CONFIG_NET_PCI and move dependencies to individual
driver config options. It looks odd that only drivers from the 10/100
Mbit category — and then, not even all — depend on this. Of course you
probably won't see Gbit adapters for ISA, but SUN, 3com, HP cards are
also available on PCI.
Jeff Kirsher puts forward in:
>
>http://vger.kernel.org/netconf2010_slides/netconf-jtk.pdf
>
>Create /drivers/net/sw for vlan, 8021q, bonding, bridging, etc drivers
That does not seem too nice. Currently, bridge is at net/bridge/, and
moving it into drivers/net/sw/bridge/ is just elongating the path name
for a rename that is.. a bit disputable as far as I read the thread.
What is in net/, leave it there for now.
drivers/net/ethernet/, I am fine with.
^ permalink raw reply [flat|nested] 38+ messages in thread
* Re: [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers
2010-12-16 12:22 ` Jan Engelhardt
@ 2010-12-17 9:51 ` Jeff Kirsher
0 siblings, 0 replies; 38+ messages in thread
From: Jeff Kirsher @ 2010-12-17 9:51 UTC (permalink / raw)
To: Jan Engelhardt; +Cc: paul.gortmaker, Joe Perches, Maciej W. Rozycki, netdev
On Thu, Dec 16, 2010 at 04:22, Jan Engelhardt <jengelh@medozas.de> wrote:
> [adding missing cc:netdev]
>
>
> A few comments, since I have just been made aware of the Netconf slides,
>
>
> Paul Gortmaker wrote:
>>
>>If in fact this series gets agreement, I'm figuring it makes sense to
>>have it go in either at the beginning of a dev cycle, or at the very
>>end
>
> I think I have seen git properly coping with renames, if your and other
> developers' branches are git-merged (patchwise application of course
> leads to rejects).
>
>
>>classifying drivers according to the physical layer they support or if
>>multiple are, such as with the Ethernet that is backwards compatible,
>>the newest variation they do?
>
> Above all I would probably like to see
>
> - getting rid of the "1000 Mbit" and "10000 Mbit" submenus. jme.ko for
> example is put under 1000 Mbit, but the jme chip I have ("197b:0260 (rev
> 02) JMicron Technology Corp. JMC260 PCI Express Fast Ethernet
> Controller") does not do 1000.
Organization of the Kconfig menus/sub-menus is also goal in this
organization of /drivers/net. I like the 10/100, 1000, and 10GbE
sub-menus, but if we find that there are issues with drivers that
support hardware in more than one category, then we should look at the
best way to handle those drivers or organization of the Ethernet
sub-menus.
>
> - getting rid of CONFIG_NET_PCI and move dependencies to individual
> driver config options. It looks odd that only drivers from the 10/100
> Mbit category — and then, not even all — depend on this. Of course you
> probably won't see Gbit adapters for ISA, but SUN, 3com, HP cards are
> also available on PCI.
Agreed, this is fixed in some of the preliminary patches that Joe and
I have been working on.
>
> Jeff Kirsher puts forward in:
>>
>>http://vger.kernel.org/netconf2010_slides/netconf-jtk.pdf
>>
>>Create /drivers/net/sw for vlan, 8021q, bonding, bridging, etc drivers
>
> That does not seem too nice. Currently, bridge is at net/bridge/, and
> moving it into drivers/net/sw/bridge/ is just elongating the path name
> for a rename that is.. a bit disputable as far as I read the thread.
The reasoning behind this idea was that we are trying to organize
/drivers/net so that we have /drivers/net/<L2 technologies> for
example:
/drivers/net/appletalk
/drivers/net/arcnet
/drivers/net/ethernet
/drivers/net/tokenring
/drivers/net/wimax
/drivers/net/wireless
Stack drivers like vlan, bonding, bridging do not fall into this and
so we thought it best to create a /drivers/net/sw directory for stack
drivers like this. For now, we planned on keeping stack drivers in
/drivers/net/. IMHO I still think that moving stack drivers to
/drivers/net/sw is still a good idea but it does not have to happen
right away.
>
> What is in net/, leave it there for now.
> drivers/net/ethernet/, I am fine with.
Most of the drivers in /drivers/net are Ethernet drivers and should
reside in /drivers/net/ethernet (if they are Ethernet drivers) when
the directory structure exists.
--
Cheers,
Jeff
^ permalink raw reply [flat|nested] 38+ messages in thread
end of thread, other threads:[~2010-12-17 9:51 UTC | newest]
Thread overview: 38+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-10-29 1:19 [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Paul Gortmaker
2010-10-29 1:19 ` [PATCH 01/15] net: introduce legacy dir to absorb 10Mbit, ISA, EISA drivers Paul Gortmaker
2010-10-29 1:19 ` [PATCH 02/15] 3c501: relocate ancient 8 bit ISA driver to legacy dir Paul Gortmaker
2010-10-29 1:19 ` [PATCH 03/15] de6xx: relocate ancient parallel port eth drivers to legacy Paul Gortmaker
2010-10-29 1:19 ` [PATCH 04/15] sun3: Relocate the sun3 specific lance/83596 " Paul Gortmaker
2010-10-29 1:19 ` [PATCH 05/15] dec netdev: relocate DIGITAL based " Paul Gortmaker
2010-10-29 4:21 ` Maciej W. Rozycki
2010-10-29 4:29 ` David Miller
2010-10-29 4:54 ` Maciej W. Rozycki
2010-10-29 5:46 ` Maciej W. Rozycki
2010-10-29 5:53 ` David Miller
2010-10-29 5:47 ` David Miller
2010-10-29 5:50 ` Maciej W. Rozycki
2010-10-29 5:53 ` David Miller
2010-10-29 6:37 ` Maciej W. Rozycki
2010-10-29 1:19 ` [PATCH 06/15] netdev: relocate i8258x and i8259x " Paul Gortmaker
2010-10-29 1:19 ` [PATCH 07/15] lance: relocate legacy 7990 " Paul Gortmaker
2010-10-29 1:19 ` [PATCH 08/15] netdev: relocate toplevel 8390 based drivers to legacy dir Paul Gortmaker
2010-10-29 1:19 ` [PATCH 09/15] netdev: relocate remaining ISA 3Com cards " Paul Gortmaker
2010-10-29 1:19 ` [PATCH 10/15] netdev: relocate more one-off drivers to the " Paul Gortmaker
2010-10-29 1:19 ` [PATCH 11/15] netdev: kill off the concept of NET_VENDOR_FOO Paul Gortmaker
2010-10-29 1:19 ` [PATCH 12/15] netdev: relocate sb1000 ISA cable modem driver to legacy Paul Gortmaker
2010-10-29 1:19 ` [PATCH 13/15] netdev: kill off NET_ISA Kconfig option Paul Gortmaker
2010-10-29 1:19 ` [PATCH 14/15] MAINTAINERS: updates for new drivers/net/legacy dir Paul Gortmaker
2010-10-29 1:19 ` [PATCH 15/15] netdev: relocate LICENSE.SRC to legacy Paul Gortmaker
2010-10-29 1:48 ` [PATCH 0/15] RFC: create drivers/net/legacy for ISA, EISA, MCA drivers Joe Perches
2010-10-29 9:40 ` David Lamparter
2010-10-29 10:13 ` Maciej W. Rozycki
2010-10-29 21:26 ` Paul Gortmaker
2010-10-29 22:08 ` Joe Perches
2010-10-30 0:01 ` Jeff Kirsher
2010-11-04 21:20 ` Paul Gortmaker
2010-11-05 2:28 ` Jeff Kirsher
2010-11-05 12:51 ` Paul Gortmaker
2010-11-18 23:52 ` Joe Perches
2010-11-19 0:34 ` Jeff Kirsher
[not found] ` <alpine.LNX.2.01.1012161253560.3000@obet.zrqbmnf.qr>
2010-12-16 12:22 ` Jan Engelhardt
2010-12-17 9:51 ` Jeff Kirsher
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.