From: Michael Schwingen <michael@schwingen.org>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 07/13] update/fix AcTux1 board
Date: Mon, 3 Jan 2011 14:45:32 +0100 [thread overview]
Message-ID: <1294062338-21084-8-git-send-email-michael@schwingen.org> (raw)
In-Reply-To: <1294062338-21084-1-git-send-email-michael@schwingen.org>
Signed-off-by: Michael Schwingen <michael@schwingen.org>
---
board/actux1/actux1.c | 22 +++++++++++---------
board/actux1/config.mk | 7 +----
board/actux1/u-boot.lds | 42 +++++++++++++++++++++++++++------------
boards.cfg | 5 +++-
include/configs/actux1.h | 48 +++++++++++++++++++++++++++------------------
5 files changed, 76 insertions(+), 48 deletions(-)
diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c
index 399be23..c56ec94 100644
--- a/board/actux1/actux1.c
+++ b/board/actux1/actux1.c
@@ -42,6 +42,17 @@
DECLARE_GLOBAL_DATA_PTR;
+int board_early_init_f (void)
+{
+ /* CS5: Debug port */
+ *IXP425_EXP_CS5 = 0x9d520003;
+ /* CS6: HwRel */
+ *IXP425_EXP_CS6 = 0x81860001;
+ /* CS7: LEDs */
+ *IXP425_EXP_CS7 = 0x80900003;
+ return 0;
+}
+
int board_init (void)
{
gd->bd->bi_arch_number = MACH_TYPE_ACTUX1;
@@ -61,13 +72,6 @@ int board_init (void)
GPIO_OUTPUT_ENABLE (CONFIG_SYS_GPIO_EXTBUS_CLK);
*IXP425_GPIO_GPCLKR = 0x011001FF;
- /* CS5: Debug port */
- *IXP425_EXP_CS5 = 0x9d520003;
- /* CS6: HwRel */
- *IXP425_EXP_CS6 = 0x81860001;
- /* CS7: LEDs */
- *IXP425_EXP_CS7 = 0x80900003;
-
udelay (533);
GPIO_OUTPUT_SET (CONFIG_SYS_GPIO_IORST);
@@ -116,9 +120,7 @@ u32 get_board_rev (void)
int dram_init (void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
return (0);
}
diff --git a/board/actux1/config.mk b/board/actux1/config.mk
index 88634f7..a370337 100644
--- a/board/actux1/config.mk
+++ b/board/actux1/config.mk
@@ -1,6 +1,3 @@
-CONFIG_SYS_TEXT_BASE = 0x00e00000
-
-# include NPE ethernet driver
-BOARDLIBS = arch/arm/cpu/ixp/npe/libnpe.o
-
LDSCRIPT := $(SRCTREE)/board/$(BOARDDIR)/u-boot.lds
+PLATFORM_RELFLAGS += -ffunction-sections -fdata-sections
+PLATFORM_LDFLAGS += --gc-sections
diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds
index 5c1ece7..6809ef7 100644
--- a/board/actux1/u-boot.lds
+++ b/board/actux1/u-boot.lds
@@ -30,15 +30,15 @@ SECTIONS
. = ALIGN (4);
.text : {
- arch/arm/cpu/ixp/start.o(.text)
- lib/string.o(.text)
- lib/vsprintf.o(.text)
- arch/arm/lib/board.o(.text)
- common/dlmalloc.o(.text)
- arch/arm/cpu/ixp/cpu.o(.text)
+ arch/arm/cpu/ixp/start.o(.text*)
+ net/libnet.o(.text*)
+ board/actux1/libactux1.o(.text*)
+ arch/arm/cpu/ixp/libixp.o(.text*)
+ drivers/serial/libserial.o(.text*)
+
. = env_offset;
common/env_embedded.o(.ppcenv)
- * (.text)
+ *(.text*)
}
. = ALIGN (4);
@@ -47,7 +47,7 @@ SECTIONS
}
. = ALIGN (4);
.data : {
- *(.data)
+ *(.data*)
}
. = ALIGN (4);
.got : {
@@ -61,10 +61,26 @@ SECTIONS
__u_boot_cmd_end =.;
. = ALIGN (4);
- __bss_start =.;
- .bss (NOLOAD): {
- *(.bss)
- . = ALIGN(4);
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss __rel_dyn_start (OVERLAY) : {
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ _end = .;
}
- _end =.;
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
}
diff --git a/boards.cfg b/boards.cfg
index 94b8745..695baca 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -122,7 +122,10 @@ omap4_panda arm armv7 panda ti
omap4_sdp4430 arm armv7 sdp4430 ti omap4
s5p_goni arm armv7 goni samsung s5pc1xx
smdkc100 arm armv7 smdkc100 samsung s5pc1xx
-actux1 arm ixp
+actux1_4_16 arm ixp actux1 - - actux1:FLASH2X2
+actux1_8_16 arm ixp actux1 - - actux1:FLASH1X8
+actux1_4_32 arm ixp actux1 - - actux1:FLASH2X2,RAM_32MB
+actux1_8_32 arm ixp actux1 - - actux1:FLASH1X8,RAM_32MB
actux2 arm ixp
actux3 arm ixp
actux4 arm ixp
diff --git a/include/configs/actux1.h b/include/configs/actux1.h
index 8886eff..2ffedf1 100644
--- a/include/configs/actux1.h
+++ b/include/configs/actux1.h
@@ -26,13 +26,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/* 1: modified board with 32MB DRAM */
-#define CONFIG_ACTUX1_32MB 0
-/* 1: 2*2MB FLASH (standard) */
-#define CONFIG_ACTUX1_FLASH2X2 1
-/* 1: 1*8MB FLASH (upgraded boards) */
-#define CONFIG_ACTUX1_FLASH1X8 0
-
#define CONFIG_IXP425 1
#define CONFIG_ACTUX1 1
@@ -44,6 +37,7 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F 1
/***************************************************************
* U-boot generic defines start here.
@@ -54,7 +48,6 @@
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-/* size in bytes reserved for initial data */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
@@ -63,8 +56,8 @@
#include <config_cmd_default.h>
#define CONFIG_CMD_ELF
-#undef CONFIG_CMD_PCI
-#undef CONFIG_PCI
+//!#undef CONFIG_CMD_PCI
+//!#undef CONFIG_PCI
#define CONFIG_BOOTCOMMAND "run boot_flash"
/* enable passing of ATAGs */
@@ -94,8 +87,9 @@
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ 3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK 66666666
+#define CONFIG_SYS_HZ 1000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x00010000
@@ -121,9 +115,9 @@
/* SDRAM settings */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
-#define CONFIG_SYS_DRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#if CONFIG_ACTUX1_32MB
+#ifdef CONFIG_RAM_32MB
# define CONFIG_SYS_SDR_CONFIG 0x18
# define PHYS_SDRAM_1_SIZE 0x02000000
# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
@@ -137,8 +131,11 @@
# define CONFIG_SYS_DRAM_SIZE 0x01000000
#endif
+
+
/* FLASH organization */
-#if CONFIG_ACTUX1_FLASH2X2
+#define CONFIG_SYS_TEXT_BASE 0x50000000
+#ifdef CONFIG_FLASH2X2
# define CONFIG_SYS_MAX_FLASH_BANKS 2
/* max number of sectors on one chip */
# define CONFIG_SYS_MAX_FLASH_SECT 40
@@ -146,7 +143,7 @@
# define PHYS_FLASH_2 0x50200000
# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 }
#endif
-#if CONFIG_ACTUX1_FLASH1X8
+#ifdef CONFIG_FLASH1X8
# define CONFIG_SYS_MAX_FLASH_BANKS 1
/* max number of sectors on one chip */
# define CONFIG_SYS_MAX_FLASH_SECT 140
@@ -173,12 +170,16 @@
#define CONFIG_NET_MULTI 1
/* NPE0 PHY address */
#define CONFIG_PHY_ADDR 0
+/* NPE1 PHY address (HW Release E only) */
+#define CONFIG_PHY1_ADDR 1
/* MII PHY management */
#define CONFIG_MII 1
/* Number of ethernet rx buffers & descriptors */
#define CONFIG_SYS_RX_ETH_BUFFER 16
#define CONFIG_RESET_PHY_R 1
+#define CONFIG_HAS_ETH1 1
+
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
@@ -203,17 +204,19 @@
#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000)
#define CONFIG_SYS_USE_PPCENV 1
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"npe_ucode=50040000\0" \
"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
"kerneladdr=50050000\0" \
+ "kernelfile=actux1/uImage\0" \
+ "rootfile=actux1/rootfs\0" \
"rootaddr=50170000\0" \
"loadaddr=10000\0" \
"updateboot_ser=mw.b 10000 ff 40000;" \
" loady ${loadaddr};" \
" run eraseboot writeboot\0" \
"updateboot_net=mw.b 10000 ff 40000;" \
- " tftp ${loadaddr} u-boot.bin;" \
+ " tftp ${loadaddr} actux1/u-boot.bin;" \
" run eraseboot writeboot\0" \
"eraseboot=protect off 50000000 50003fff;" \
" protect off 50006000 5003ffff;" \
@@ -223,6 +226,9 @@
" cp.b 16000 50006000 3a000\0" \
"eraseenv=protect off 50004000 50005fff;" \
" erase 50004000 50005fff\0" \
+ "updateucode=loady;" \
+ " era ${npe_ucode} +${filesize};" \
+ " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \
"updateroot=tftp ${loadaddr} ${rootfile};" \
" era ${rootaddr} +${filesize};" \
" cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
@@ -233,7 +239,7 @@
" rootfstype=squashfs,jffs2 init=/etc/preinit\0" \
"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \
" rootfstype=squashfs,jffs2 init=/etc/preinit\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \
"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \
"boot_flash=run flashargs addtty addeth;" \
" bootm ${kerneladdr}\0" \
@@ -241,4 +247,8 @@
" tftpboot ${loadaddr} ${kernelfile};" \
" bootm\0"
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */
--
1.7.2.3
next prev parent reply other threads:[~2011-01-03 13:45 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-01-03 13:45 [U-Boot] IXP42x patch series - 2nd attempt Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 01/13] add XScale sub architecture (IXP/PXA) to board list Michael Schwingen
2011-01-25 20:38 ` Wolfgang Denk
2011-01-25 23:39 ` Michael Schwingen
2011-01-26 7:30 ` Wolfgang Denk
2011-04-07 13:29 ` Marek Vasut
2011-04-07 14:58 ` Wolfgang Denk
2011-04-07 16:41 ` Marek Vasut
2011-05-20 23:49 ` Marek Vasut
2011-05-19 15:48 ` Marek Vasut
2011-01-03 13:45 ` [U-Boot] [PATCH 02/13] add support for IXP42x Rev. B1 and newer Michael Schwingen
2011-01-25 20:39 ` Wolfgang Denk
2011-01-03 13:45 ` [U-Boot] [PATCH 03/13] trigger hardware watchdog in IXP42x serial driver Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 04/13] Fix IXP code to work after relocation was added Michael Schwingen
2011-01-25 20:42 ` Wolfgang Denk
2011-01-03 13:45 ` [U-Boot] [PATCH 05/13] fix "depend" target in npe directory Michael Schwingen
2011-01-25 20:42 ` Wolfgang Denk
2011-01-26 23:22 ` Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 06/13] add wildcard to sections (for -ffunction-sections/-fdata-sections) Michael Schwingen
2011-01-03 13:45 ` Michael Schwingen [this message]
2011-01-25 20:44 ` [U-Boot] [PATCH 07/13] update/fix AcTux1 board Wolfgang Denk
2011-01-25 23:37 ` Michael Schwingen
2011-01-26 7:26 ` Wolfgang Denk
2011-01-29 15:57 ` Michael Schwingen
2011-01-31 19:01 ` Scott Wood
2011-01-31 19:20 ` Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 08/13] update/fix AcTux2 board Michael Schwingen
2011-01-25 20:46 ` Wolfgang Denk
2011-01-26 9:34 ` Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 09/13] update/fix AcTux3 board Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 10/13] update/fix AcTux4 board Michael Schwingen
2011-01-03 13:45 ` [U-Boot] [PATCH 11/13] update/fix some more IXP42x boards (only compile tested) Michael Schwingen
2011-01-25 20:47 ` Wolfgang Denk
2011-01-25 23:43 ` Michael Schwingen
2011-01-26 7:34 ` Wolfgang Denk
2011-01-03 13:45 ` [U-Boot] [PATCH 12/13] IXP NPE: add support for fixed-speed MII ports Michael Schwingen
2011-01-25 20:48 ` Wolfgang Denk
2011-01-03 13:45 ` [U-Boot] [PATCH 13/13] add dvlhost (dLAN 200 AV Wireless G) board Michael Schwingen
2011-01-25 20:36 ` Wolfgang Denk
2011-01-25 23:45 ` Michael Schwingen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1294062338-21084-8-git-send-email-michael@schwingen.org \
--to=michael@schwingen.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.