[PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[Sylwester Nawrocki]

Hello,

the following patch series adds the common platform code for configuration 
of the MIPI CSIS and MIPI DSIM PHYs on S5PV210 and S5PV310 SoCs.
The spinlock is used to avoid races while the common PHY control register
is accessed from within MIPI DSIM and MIPI CSIS drivers.
The common PHY enable bit is cleared only when both CSIS and DSIM devices
are not in use.


The patch series contains:

[PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control
[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup
[PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS setup

Rebased onto kgene-for-next branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git 


Regards,
Sylwester


--
Sylwester Nawrocki
Samsung Poland R&D Center

[PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[Sylwester Nawrocki]

Hello,

the following patch series adds the common platform code for configuration 
of the MIPI CSIS and MIPI DSIM PHYs on S5PV210 and S5PV310 SoCs.
The spinlock is used to avoid races while the common PHY control register
is accessed from within MIPI DSIM and MIPI CSIS drivers.
The common PHY enable bit is cleared only when both CSIS and DSIM devices
are not in use.


The patch series contains:

[PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control
[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup
[PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS setup

Rebased onto kgene-for-next branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git 


Regards,
Sylwester


--
Sylwester Nawrocki
Samsung Poland R&D Center

[PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control

[Sylwester Nawrocki]

The phy_enable callback in struct s5p_platform_mipi_csis is added
to allow the CSIS driver to control its PHY enable and reset signals.
This allows to use same MIPI CSIS driver across various SoCs.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/plat-s5p/dev-csis0.c              |    2 +-
 arch/arm/plat-s5p/dev-csis1.c              |    2 +-
 arch/arm/plat-s5p/include/plat/csis.h      |   28 --------------------
 arch/arm/plat-s5p/include/plat/mipi_csis.h |   39 ++++++++++++++++++++++++++++
 4 files changed, 41 insertions(+), 30 deletions(-)
 delete mode 100644 arch/arm/plat-s5p/include/plat/csis.h
 create mode 100644 arch/arm/plat-s5p/include/plat/mipi_csis.h

diff --git a/arch/arm/plat-s5p/dev-csis0.c b/arch/arm/plat-s5p/dev-csis0.c
index dfab1c8..57efe9c 100644
--- a/arch/arm/plat-s5p/dev-csis0.c
+++ b/arch/arm/plat-s5p/dev-csis0.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2010 Samsung Electronics
+ * Copyright (C) 2010 Samsung Electronics Co., Ltd
  *
  * S5P series device definition for MIPI-CSIS channel 0
  *
diff --git a/arch/arm/plat-s5p/dev-csis1.c b/arch/arm/plat-s5p/dev-csis1.c
index e3053f2..c61b46b 100644
--- a/arch/arm/plat-s5p/dev-csis1.c
+++ b/arch/arm/plat-s5p/dev-csis1.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2010 Samsung Electronics
+ * Copyright (C) 2010 Samsung Electronics Co., Ltd
  *
  * S5P series device definition for MIPI-CSIS channel 1
  *
diff --git a/arch/arm/plat-s5p/include/plat/csis.h b/arch/arm/plat-s5p/include/plat/csis.h
deleted file mode 100644
index 51e308c..0000000
--- a/arch/arm/plat-s5p/include/plat/csis.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * Copyright (C) 2010 Samsung Electronics
- *
- * S5P series MIPI CSI slave device support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef PLAT_S5P_CSIS_H_
-#define PLAT_S5P_CSIS_H_ __FILE__
-
-/**
- * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
- * @clk_rate: bus clock frequency
- * @lanes: number of data lanes used
- * @alignment: data alignment in bits
- * @hs_settle: HS-RX settle time
- */
-struct s5p_platform_mipi_csis {
-	unsigned long clk_rate;
-	u8 lanes;
-	u8 alignment;
-	u8 hs_settle;
-};
-
-#endif /* PLAT_S5P_CSIS_H_ */
diff --git a/arch/arm/plat-s5p/include/plat/mipi_csis.h b/arch/arm/plat-s5p/include/plat/mipi_csis.h
new file mode 100644
index 0000000..0b22065
--- /dev/null
+++ b/arch/arm/plat-s5p/include/plat/mipi_csis.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2010 Samsung Electronics, Co. Ltd
+ *
+ * S5P series MIPI CSI slave device support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef PLAT_S5P_MIPI_CSIS_H_
+#define PLAT_S5P_MIPI_CSIS_H_ __FILE__
+
+struct platform_device;
+
+/**
+ * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
+ * @clk_rate: bus clock frequency
+ * @lanes: number of data lanes used
+ * @alignment: data alignment in bits
+ * @hs_settle: HS-RX settle time
+ */
+struct s5p_platform_mipi_csis {
+	unsigned long clk_rate;
+	u8 lanes;
+	u8 alignment;
+	u8 hs_settle;
+	int (*phy_enable)(struct platform_device *pdev, bool on);
+};
+
+/**
+ * struct s5p_csis_phy_control - global MIPI-CSIS PHY control
+ * @pdev: platform device the mipi phy state is to be changed for
+ * @on: true to enable CSIS PHY and assert its reset,
+ *	false will disable the PHY and put into reset state
+ */
+int s5p_csis_phy_enable(struct platform_device *pdev, bool on);
+
+#endif /* PLAT_S5P_MIPI_CSIS_H_ */
-- 
1.7.3.4

[PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control

[Sylwester Nawrocki]

The phy_enable callback in struct s5p_platform_mipi_csis is added
to allow the CSIS driver to control its PHY enable and reset signals.
This allows to use same MIPI CSIS driver across various SoCs.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/plat-s5p/dev-csis0.c              |    2 +-
 arch/arm/plat-s5p/dev-csis1.c              |    2 +-
 arch/arm/plat-s5p/include/plat/csis.h      |   28 --------------------
 arch/arm/plat-s5p/include/plat/mipi_csis.h |   39 ++++++++++++++++++++++++++++
 4 files changed, 41 insertions(+), 30 deletions(-)
 delete mode 100644 arch/arm/plat-s5p/include/plat/csis.h
 create mode 100644 arch/arm/plat-s5p/include/plat/mipi_csis.h

diff --git a/arch/arm/plat-s5p/dev-csis0.c b/arch/arm/plat-s5p/dev-csis0.c
index dfab1c8..57efe9c 100644
--- a/arch/arm/plat-s5p/dev-csis0.c
+++ b/arch/arm/plat-s5p/dev-csis0.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2010 Samsung Electronics
+ * Copyright (C) 2010 Samsung Electronics Co., Ltd
  *
  * S5P series device definition for MIPI-CSIS channel 0
  *
diff --git a/arch/arm/plat-s5p/dev-csis1.c b/arch/arm/plat-s5p/dev-csis1.c
index e3053f2..c61b46b 100644
--- a/arch/arm/plat-s5p/dev-csis1.c
+++ b/arch/arm/plat-s5p/dev-csis1.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2010 Samsung Electronics
+ * Copyright (C) 2010 Samsung Electronics Co., Ltd
  *
  * S5P series device definition for MIPI-CSIS channel 1
  *
diff --git a/arch/arm/plat-s5p/include/plat/csis.h b/arch/arm/plat-s5p/include/plat/csis.h
deleted file mode 100644
index 51e308c..0000000
--- a/arch/arm/plat-s5p/include/plat/csis.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * Copyright (C) 2010 Samsung Electronics
- *
- * S5P series MIPI CSI slave device support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef PLAT_S5P_CSIS_H_
-#define PLAT_S5P_CSIS_H_ __FILE__
-
-/**
- * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
- * @clk_rate: bus clock frequency
- * @lanes: number of data lanes used
- * @alignment: data alignment in bits
- * @hs_settle: HS-RX settle time
- */
-struct s5p_platform_mipi_csis {
-	unsigned long clk_rate;
-	u8 lanes;
-	u8 alignment;
-	u8 hs_settle;
-};
-
-#endif /* PLAT_S5P_CSIS_H_ */
diff --git a/arch/arm/plat-s5p/include/plat/mipi_csis.h b/arch/arm/plat-s5p/include/plat/mipi_csis.h
new file mode 100644
index 0000000..0b22065
--- /dev/null
+++ b/arch/arm/plat-s5p/include/plat/mipi_csis.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2010 Samsung Electronics, Co. Ltd
+ *
+ * S5P series MIPI CSI slave device support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef PLAT_S5P_MIPI_CSIS_H_
+#define PLAT_S5P_MIPI_CSIS_H_ __FILE__
+
+struct platform_device;
+
+/**
+ * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
+ * @clk_rate: bus clock frequency
+ * @lanes: number of data lanes used
+ * @alignment: data alignment in bits
+ * @hs_settle: HS-RX settle time
+ */
+struct s5p_platform_mipi_csis {
+	unsigned long clk_rate;
+	u8 lanes;
+	u8 alignment;
+	u8 hs_settle;
+	int (*phy_enable)(struct platform_device *pdev, bool on);
+};
+
+/**
+ * struct s5p_csis_phy_control - global MIPI-CSIS PHY control
+ * @pdev: platform device the mipi phy state is to be changed for
+ * @on: true to enable CSIS PHY and assert its reset,
+ *	false will disable the PHY and put into reset state
+ */
+int s5p_csis_phy_enable(struct platform_device *pdev, bool on);
+
+#endif /* PLAT_S5P_MIPI_CSIS_H_ */
-- 
1.7.3.4

[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
and MIPI CSIS drivers so a spinlock is used to protect multiple
access to these registers. Also a proper state of a common
PHY enable bit is maintained in order to avoid a DSIM
and CSIS driver conflict.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/mach-s5pv310/Kconfig                 |    6 ++
 arch/arm/mach-s5pv310/Makefile                |    2 +
 arch/arm/mach-s5pv310/include/mach/map.h      |    7 +--
 arch/arm/mach-s5pv310/include/mach/regs-pmu.h |    6 ++
 arch/arm/mach-s5pv310/setup-mipi.c            |   62 +++++++++++++++++++++++++
 5 files changed, 79 insertions(+), 4 deletions(-)
 create mode 100644 arch/arm/mach-s5pv310/setup-mipi.c

diff --git a/arch/arm/mach-s5pv310/Kconfig b/arch/arm/mach-s5pv310/Kconfig
index b7aa3cd..2420076 100644
--- a/arch/arm/mach-s5pv310/Kconfig
+++ b/arch/arm/mach-s5pv310/Kconfig
@@ -15,6 +15,11 @@ config CPU_S5PV310
 	help
 	  Enable S5PV310 CPU support
 
+config S5PV310_SETUP_MIPI
+	bool
+	help
+	  Common setup code for MIPI CSIS/DSIM channels 0 and 1.
+
 config S5PV310_DEV_PD
 	bool
 	help
@@ -96,6 +101,7 @@ config MACH_UNIVERSAL_C210
 	select S3C_DEV_HSMMC3
 	select S5PV310_SETUP_SDHCI
 	select S3C_DEV_I2C1
+	select S5PV310_SETUP_MIPI
 	select S5PV310_SETUP_I2C1
 	help
 	  Machine support for Samsung Mobile Universal S5PC210 Reference
diff --git a/arch/arm/mach-s5pv310/Makefile b/arch/arm/mach-s5pv310/Makefile
index 651f193..7f1b89b 100644
--- a/arch/arm/mach-s5pv310/Makefile
+++ b/arch/arm/mach-s5pv310/Makefile
@@ -29,6 +29,8 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+= mach-universal_c210.o
 # device support
 
 obj-y					+= dev-audio.o
+
+obj-$(CONFIG_S5PV310_SETUP_MIPI)	+= setup-mipi.o
 obj-$(CONFIG_S5PV310_DEV_PD)		+= dev-pd.o
 
 obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
diff --git a/arch/arm/mach-s5pv310/include/mach/map.h b/arch/arm/mach-s5pv310/include/mach/map.h
index 33bcff2..6635287 100644
--- a/arch/arm/mach-s5pv310/include/mach/map.h
+++ b/arch/arm/mach-s5pv310/include/mach/map.h
@@ -65,8 +65,7 @@
 #define S5PV310_PA_GPIO2		(0x11000000)
 #define S5PV310_PA_GPIO3		(0x03860000)
 
-#define S5PV310_PA_MIPI_CSIS0		0x11880000
-#define S5PV310_PA_MIPI_CSIS1		0x11890000
+#define S5PV310_PA_MIPI_CSIS(x)		(0x11880000 + ((x) * 0x10000))
 
 #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
 
@@ -124,7 +123,7 @@
 #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
 #define S3C_PA_RTC			S5PV310_PA_RTC
 #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
-#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
-#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
+#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS(0)
+#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS(1)
 
 #endif /* __ASM_ARCH_MAP_H */
diff --git a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
index fb333d0..bef8102 100644
--- a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
+++ b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
@@ -27,4 +27,10 @@
 
 #define S5P_INT_LOCAL_PWR_EN		0x7
 
+#define S5P_MIPI_PHY0_CONTROL		S5P_PMUREG(0x0710)
+#define S5P_MIPI_PHY1_CONTROL		S5P_PMUREG(0x0714)
+#define S5P_MIPI_PHY_ENABLE		(1 << 0)
+#define S5P_MIPI_PHY_SRESETN		(1 << 1)
+#define S5P_MIPI_PHY_MRESETN		(1 << 2)
+
 #endif /* __ASM_ARCH_REGS_PMU_H */
diff --git a/arch/arm/mach-s5pv310/setup-mipi.c b/arch/arm/mach-s5pv310/setup-mipi.c
new file mode 100644
index 0000000..fc91a29
--- /dev/null
+++ b/arch/arm/mach-s5pv310/setup-mipi.c
@@ -0,0 +1,62 @@
+/* linux/arch/arm/mach-s5pv310/setup-mipi.c
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd
+ *
+ * S5PV310 - Helper functions for MIPI CSIS/DSIM PHY control
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <mach/regs-pmu.h>
+
+/* Global MIPI CSIS or DSIM PHY enable and reset control. */
+static int s5p_mipi_phy_control(struct platform_device *pdev, bool on, u32 rst)
+{
+	static DEFINE_SPINLOCK(lock);
+	void __iomem *addr;
+	unsigned long flags;
+	int pid;
+	u32 cfg;
+
+	if (pdev == NULL)
+		return -EINVAL;
+
+	pid = pdev->id;
+	if (pid != 0 && pid != 1)
+		return -EINVAL;
+
+	addr = pid ? S5P_MIPI_PHY1_CONTROL : S5P_MIPI_PHY0_CONTROL;
+
+	spin_lock_irqsave(&lock, flags);
+
+	cfg = __raw_readl(addr) & ~rst;
+	if (on)
+		cfg |= rst;
+	__raw_writel(cfg, addr);
+
+	if (on)
+		cfg |= S5P_MIPI_PHY_ENABLE;
+	else if (!(cfg & (S5P_MIPI_PHY_SRESETN | S5P_MIPI_PHY_MRESETN) & ~rst))
+		cfg &= ~S5P_MIPI_PHY_ENABLE;
+
+	__raw_writel(cfg, addr);
+
+	spin_unlock_irqrestore(&lock, flags);
+	return 0;
+}
+
+int s5p_csis_phy_enable(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_SRESETN);
+}
+
+int s5p_dsim_phy_enable(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_MRESETN);
+}
-- 
1.7.3.4

[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
and MIPI CSIS drivers so a spinlock is used to protect multiple
access to these registers. Also a proper state of a common
PHY enable bit is maintained in order to avoid a DSIM
and CSIS driver conflict.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/mach-s5pv310/Kconfig                 |    6 ++
 arch/arm/mach-s5pv310/Makefile                |    2 +
 arch/arm/mach-s5pv310/include/mach/map.h      |    7 +--
 arch/arm/mach-s5pv310/include/mach/regs-pmu.h |    6 ++
 arch/arm/mach-s5pv310/setup-mipi.c            |   62 +++++++++++++++++++++++++
 5 files changed, 79 insertions(+), 4 deletions(-)
 create mode 100644 arch/arm/mach-s5pv310/setup-mipi.c

diff --git a/arch/arm/mach-s5pv310/Kconfig b/arch/arm/mach-s5pv310/Kconfig
index b7aa3cd..2420076 100644
--- a/arch/arm/mach-s5pv310/Kconfig
+++ b/arch/arm/mach-s5pv310/Kconfig
@@ -15,6 +15,11 @@ config CPU_S5PV310
 	help
 	  Enable S5PV310 CPU support
 
+config S5PV310_SETUP_MIPI
+	bool
+	help
+	  Common setup code for MIPI CSIS/DSIM channels 0 and 1.
+
 config S5PV310_DEV_PD
 	bool
 	help
@@ -96,6 +101,7 @@ config MACH_UNIVERSAL_C210
 	select S3C_DEV_HSMMC3
 	select S5PV310_SETUP_SDHCI
 	select S3C_DEV_I2C1
+	select S5PV310_SETUP_MIPI
 	select S5PV310_SETUP_I2C1
 	help
 	  Machine support for Samsung Mobile Universal S5PC210 Reference
diff --git a/arch/arm/mach-s5pv310/Makefile b/arch/arm/mach-s5pv310/Makefile
index 651f193..7f1b89b 100644
--- a/arch/arm/mach-s5pv310/Makefile
+++ b/arch/arm/mach-s5pv310/Makefile
@@ -29,6 +29,8 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+= mach-universal_c210.o
 # device support
 
 obj-y					+= dev-audio.o
+
+obj-$(CONFIG_S5PV310_SETUP_MIPI)	+= setup-mipi.o
 obj-$(CONFIG_S5PV310_DEV_PD)		+= dev-pd.o
 
 obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
diff --git a/arch/arm/mach-s5pv310/include/mach/map.h b/arch/arm/mach-s5pv310/include/mach/map.h
index 33bcff2..6635287 100644
--- a/arch/arm/mach-s5pv310/include/mach/map.h
+++ b/arch/arm/mach-s5pv310/include/mach/map.h
@@ -65,8 +65,7 @@
 #define S5PV310_PA_GPIO2		(0x11000000)
 #define S5PV310_PA_GPIO3		(0x03860000)
 
-#define S5PV310_PA_MIPI_CSIS0		0x11880000
-#define S5PV310_PA_MIPI_CSIS1		0x11890000
+#define S5PV310_PA_MIPI_CSIS(x)		(0x11880000 + ((x) * 0x10000))
 
 #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
 
@@ -124,7 +123,7 @@
 #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
 #define S3C_PA_RTC			S5PV310_PA_RTC
 #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
-#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
-#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
+#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS(0)
+#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS(1)
 
 #endif /* __ASM_ARCH_MAP_H */
diff --git a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
index fb333d0..bef8102 100644
--- a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
+++ b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
@@ -27,4 +27,10 @@
 
 #define S5P_INT_LOCAL_PWR_EN		0x7
 
+#define S5P_MIPI_PHY0_CONTROL		S5P_PMUREG(0x0710)
+#define S5P_MIPI_PHY1_CONTROL		S5P_PMUREG(0x0714)
+#define S5P_MIPI_PHY_ENABLE		(1 << 0)
+#define S5P_MIPI_PHY_SRESETN		(1 << 1)
+#define S5P_MIPI_PHY_MRESETN		(1 << 2)
+
 #endif /* __ASM_ARCH_REGS_PMU_H */
diff --git a/arch/arm/mach-s5pv310/setup-mipi.c b/arch/arm/mach-s5pv310/setup-mipi.c
new file mode 100644
index 0000000..fc91a29
--- /dev/null
+++ b/arch/arm/mach-s5pv310/setup-mipi.c
@@ -0,0 +1,62 @@
+/* linux/arch/arm/mach-s5pv310/setup-mipi.c
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd
+ *
+ * S5PV310 - Helper functions for MIPI CSIS/DSIM PHY control
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <mach/regs-pmu.h>
+
+/* Global MIPI CSIS or DSIM PHY enable and reset control. */
+static int s5p_mipi_phy_control(struct platform_device *pdev, bool on, u32 rst)
+{
+	static DEFINE_SPINLOCK(lock);
+	void __iomem *addr;
+	unsigned long flags;
+	int pid;
+	u32 cfg;
+
+	if (pdev == NULL)
+		return -EINVAL;
+
+	pid = pdev->id;
+	if (pid != 0 && pid != 1)
+		return -EINVAL;
+
+	addr = pid ? S5P_MIPI_PHY1_CONTROL : S5P_MIPI_PHY0_CONTROL;
+
+	spin_lock_irqsave(&lock, flags);
+
+	cfg = __raw_readl(addr) & ~rst;
+	if (on)
+		cfg |= rst;
+	__raw_writel(cfg, addr);
+
+	if (on)
+		cfg |= S5P_MIPI_PHY_ENABLE;
+	else if (!(cfg & (S5P_MIPI_PHY_SRESETN | S5P_MIPI_PHY_MRESETN) & ~rst))
+		cfg &= ~S5P_MIPI_PHY_ENABLE;
+
+	__raw_writel(cfg, addr);
+
+	spin_unlock_irqrestore(&lock, flags);
+	return 0;
+}
+
+int s5p_csis_phy_enable(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_SRESETN);
+}
+
+int s5p_dsim_phy_enable(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_MRESETN);
+}
-- 
1.7.3.4

[PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

This platform callback allows the MIPI DSIM and CSIS drivers
to control their corresponding PHYs without conflicts.
This patch also enables the MIPI setup code on Aquila board.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/mach-s5pv210/Kconfig                   |    6 +++
 arch/arm/mach-s5pv210/Makefile                  |    1 +
 arch/arm/mach-s5pv210/include/mach/regs-clock.h |    4 ++
 arch/arm/mach-s5pv210/setup-mipi.c              |   52 +++++++++++++++++++++++
 4 files changed, 63 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-s5pv210/setup-mipi.c

diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 53aabef..b93ea37 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -37,6 +37,11 @@ config S5PV210_SETUP_FB_24BPP
 	help
           Common setup code for S5PV210 with an 24bpp RGB display helper.
 
+config S5PV210_SETUP_MIPI
+	bool
+	help
+	  Common setup code for S5PV210 MIPI DSIM/CSIS configuration.
+
 config S5PV210_SETUP_KEYPAD
 	bool
 	help
@@ -62,6 +67,7 @@ config MACH_AQUILA
 	select S5P_DEV_FIMC0
 	select S5P_DEV_FIMC1
 	select S5P_DEV_FIMC2
+	select S5PV210_SETUP_MIPI
 	select S3C_DEV_HSMMC
 	select S3C_DEV_HSMMC1
 	select S3C_DEV_HSMMC2
diff --git a/arch/arm/mach-s5pv210/Makefile b/arch/arm/mach-s5pv210/Makefile
index ff1a0db..fd01315 100644
--- a/arch/arm/mach-s5pv210/Makefile
+++ b/arch/arm/mach-s5pv210/Makefile
@@ -31,6 +31,7 @@ obj-y				+= dev-audio.o
 obj-$(CONFIG_S3C64XX_DEV_SPI)	+= dev-spi.o
 
 obj-$(CONFIG_S5PV210_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
+obj-$(CONFIG_S5PV210_SETUP_MIPI)	+= setup-mipi.o
 obj-$(CONFIG_S5PV210_SETUP_I2C1) 	+= setup-i2c1.o
 obj-$(CONFIG_S5PV210_SETUP_I2C2) 	+= setup-i2c2.o
 obj-$(CONFIG_S5PV210_SETUP_IDE)		+= setup-ide.o
diff --git a/arch/arm/mach-s5pv210/include/mach/regs-clock.h b/arch/arm/mach-s5pv210/include/mach/regs-clock.h
index 4c45b74..89b88eb 100644
--- a/arch/arm/mach-s5pv210/include/mach/regs-clock.h
+++ b/arch/arm/mach-s5pv210/include/mach/regs-clock.h
@@ -162,6 +162,10 @@
 #define S5P_MIPI_PHY_CON0	S5P_CLKREG(0x7200)
 #define S5P_MIPI_PHY_CON1	S5P_CLKREG(0x7204)
 #define S5P_MIPI_DPHY_CONTROL	S5P_CLKREG(0xE814)
+#define S5P_MIPI_DPHY_ENABLE	(1 << 0)
+#define S5P_MIPI_DPHY_SRESETN	(1 << 1)
+#define S5P_MIPI_DPHY_MRESETN	(1 << 2)
+
 
 #define S5P_IDLE_CFG_TL_MASK	(3 << 30)
 #define S5P_IDLE_CFG_TM_MASK	(3 << 28)
diff --git a/arch/arm/mach-s5pv210/setup-mipi.c b/arch/arm/mach-s5pv210/setup-mipi.c
new file mode 100644
index 0000000..f644e8c
--- /dev/null
+++ b/arch/arm/mach-s5pv210/setup-mipi.c
@@ -0,0 +1,52 @@
+/* linux/arch/arm/mach-s5pv210/setup-mipi.c
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd
+ *
+ * S5PV210 - Helper functions for MIPI CSIS/DSIM PHY control
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <mach/regs-clock.h>
+
+/* Global MIPI CSIS or DSIM PHY enable and reset control. */
+int s5p_mipi_phy_control(struct platform_device *pdev, bool on, u32 rst)
+{
+	static DEFINE_SPINLOCK(lock);
+	unsigned long flags;
+	u32 cfg;
+
+	spin_lock_irqsave(&lock, flags);
+
+	cfg = __raw_readl(S5P_MIPI_DPHY_CONTROL) & ~rst;
+	if (on)
+		cfg |= rst;
+	__raw_writel(cfg, S5P_MIPI_DPHY_CONTROL);
+
+	if (on)
+		cfg |= S5P_MIPI_DPHY_ENABLE;
+	else if (!(cfg & (S5P_MIPI_DPHY_SRESETN | S5P_MIPI_DPHY_MRESETN) & ~rst))
+		cfg &= ~S5P_MIPI_DPHY_ENABLE;
+
+	__raw_writel(cfg, S5P_MIPI_DPHY_CONTROL);
+
+	spin_unlock_irqrestore(&lock, flags);
+
+	return 0;
+}
+
+int s5p_csis_phy_control(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_DPHY_SRESETN);
+}
+
+int s5p_dsim_phy_control(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_DPHY_MRESETN);
+}
-- 
1.7.3.4

[PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

This platform callback allows the MIPI DSIM and CSIS drivers
to control their corresponding PHYs without conflicts.
This patch also enables the MIPI setup code on Aquila board.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/mach-s5pv210/Kconfig                   |    6 +++
 arch/arm/mach-s5pv210/Makefile                  |    1 +
 arch/arm/mach-s5pv210/include/mach/regs-clock.h |    4 ++
 arch/arm/mach-s5pv210/setup-mipi.c              |   52 +++++++++++++++++++++++
 4 files changed, 63 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-s5pv210/setup-mipi.c

diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 53aabef..b93ea37 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -37,6 +37,11 @@ config S5PV210_SETUP_FB_24BPP
 	help
           Common setup code for S5PV210 with an 24bpp RGB display helper.
 
+config S5PV210_SETUP_MIPI
+	bool
+	help
+	  Common setup code for S5PV210 MIPI DSIM/CSIS configuration.
+
 config S5PV210_SETUP_KEYPAD
 	bool
 	help
@@ -62,6 +67,7 @@ config MACH_AQUILA
 	select S5P_DEV_FIMC0
 	select S5P_DEV_FIMC1
 	select S5P_DEV_FIMC2
+	select S5PV210_SETUP_MIPI
 	select S3C_DEV_HSMMC
 	select S3C_DEV_HSMMC1
 	select S3C_DEV_HSMMC2
diff --git a/arch/arm/mach-s5pv210/Makefile b/arch/arm/mach-s5pv210/Makefile
index ff1a0db..fd01315 100644
--- a/arch/arm/mach-s5pv210/Makefile
+++ b/arch/arm/mach-s5pv210/Makefile
@@ -31,6 +31,7 @@ obj-y				+= dev-audio.o
 obj-$(CONFIG_S3C64XX_DEV_SPI)	+= dev-spi.o
 
 obj-$(CONFIG_S5PV210_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
+obj-$(CONFIG_S5PV210_SETUP_MIPI)	+= setup-mipi.o
 obj-$(CONFIG_S5PV210_SETUP_I2C1) 	+= setup-i2c1.o
 obj-$(CONFIG_S5PV210_SETUP_I2C2) 	+= setup-i2c2.o
 obj-$(CONFIG_S5PV210_SETUP_IDE)		+= setup-ide.o
diff --git a/arch/arm/mach-s5pv210/include/mach/regs-clock.h b/arch/arm/mach-s5pv210/include/mach/regs-clock.h
index 4c45b74..89b88eb 100644
--- a/arch/arm/mach-s5pv210/include/mach/regs-clock.h
+++ b/arch/arm/mach-s5pv210/include/mach/regs-clock.h
@@ -162,6 +162,10 @@
 #define S5P_MIPI_PHY_CON0	S5P_CLKREG(0x7200)
 #define S5P_MIPI_PHY_CON1	S5P_CLKREG(0x7204)
 #define S5P_MIPI_DPHY_CONTROL	S5P_CLKREG(0xE814)
+#define S5P_MIPI_DPHY_ENABLE	(1 << 0)
+#define S5P_MIPI_DPHY_SRESETN	(1 << 1)
+#define S5P_MIPI_DPHY_MRESETN	(1 << 2)
+
 
 #define S5P_IDLE_CFG_TL_MASK	(3 << 30)
 #define S5P_IDLE_CFG_TM_MASK	(3 << 28)
diff --git a/arch/arm/mach-s5pv210/setup-mipi.c b/arch/arm/mach-s5pv210/setup-mipi.c
new file mode 100644
index 0000000..f644e8c
--- /dev/null
+++ b/arch/arm/mach-s5pv210/setup-mipi.c
@@ -0,0 +1,52 @@
+/* linux/arch/arm/mach-s5pv210/setup-mipi.c
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd
+ *
+ * S5PV210 - Helper functions for MIPI CSIS/DSIM PHY control
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <mach/regs-clock.h>
+
+/* Global MIPI CSIS or DSIM PHY enable and reset control. */
+int s5p_mipi_phy_control(struct platform_device *pdev, bool on, u32 rst)
+{
+	static DEFINE_SPINLOCK(lock);
+	unsigned long flags;
+	u32 cfg;
+
+	spin_lock_irqsave(&lock, flags);
+
+	cfg = __raw_readl(S5P_MIPI_DPHY_CONTROL) & ~rst;
+	if (on)
+		cfg |= rst;
+	__raw_writel(cfg, S5P_MIPI_DPHY_CONTROL);
+
+	if (on)
+		cfg |= S5P_MIPI_DPHY_ENABLE;
+	else if (!(cfg & (S5P_MIPI_DPHY_SRESETN | S5P_MIPI_DPHY_MRESETN) & ~rst))
+		cfg &= ~S5P_MIPI_DPHY_ENABLE;
+
+	__raw_writel(cfg, S5P_MIPI_DPHY_CONTROL);
+
+	spin_unlock_irqrestore(&lock, flags);
+
+	return 0;
+}
+
+int s5p_csis_phy_control(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_DPHY_SRESETN);
+}
+
+int s5p_dsim_phy_control(struct platform_device *pdev, bool on)
+{
+	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_DPHY_MRESETN);
+}
-- 
1.7.3.4

Re: [PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[Sylwester Nawrocki]

On 01/04/2011 04:09 PM, Sylwester Nawrocki wrote:
> Hello,
>
> the following patch series adds the common platform code for configuration
> of the MIPI CSIS and MIPI DSIM PHYs on S5PV210 and S5PV310 SoCs.
> The spinlock is used to avoid races while the common PHY control register
> is accessed from within MIPI DSIM and MIPI CSIS drivers.
> The common PHY enable bit is cleared only when both CSIS and DSIM devices
> are not in use.
>
>
> The patch series contains:
>
> [PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control
> [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup
> [PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS setup
>

Any comments on this one?

Regards,
Sylwester

[PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[Sylwester Nawrocki]

On 01/04/2011 04:09 PM, Sylwester Nawrocki wrote:
> Hello,
>
> the following patch series adds the common platform code for configuration
> of the MIPI CSIS and MIPI DSIM PHYs on S5PV210 and S5PV310 SoCs.
> The spinlock is used to avoid races while the common PHY control register
> is accessed from within MIPI DSIM and MIPI CSIS drivers.
> The common PHY enable bit is cleared only when both CSIS and DSIM devices
> are not in use.
>
>
> The patch series contains:
>
> [PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control
> [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup
> [PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS setup
>

Any comments on this one?

Regards,
Sylwester

RE: [PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> On 01/04/2011 04:09 PM, Sylwester Nawrocki wrote:
> > Hello,
> >
> > the following patch series adds the common platform code for configuration
> > of the MIPI CSIS and MIPI DSIM PHYs on S5PV210 and S5PV310 SoCs.
> > The spinlock is used to avoid races while the common PHY control register
> > is accessed from within MIPI DSIM and MIPI CSIS drivers.
> > The common PHY enable bit is cleared only when both CSIS and DSIM devices
> > are not in use.
> >
> >
> > The patch series contains:
> >
> > [PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control
> > [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS
> setup
> > [PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS
> setup
> >
> 
> Any comments on this one?
> 
Hi,

It's 38 merge window now. So I want to wait until after this merge window.

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

[PATCH/RFC 0/3] ARM: S5P: Add a common platform setup code for MIPI CSIS/DSIM

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> On 01/04/2011 04:09 PM, Sylwester Nawrocki wrote:
> > Hello,
> >
> > the following patch series adds the common platform code for configuration
> > of the MIPI CSIS and MIPI DSIM PHYs on S5PV210 and S5PV310 SoCs.
> > The spinlock is used to avoid races while the common PHY control register
> > is accessed from within MIPI DSIM and MIPI CSIS drivers.
> > The common PHY enable bit is cleared only when both CSIS and DSIM devices
> > are not in use.
> >
> >
> > The patch series contains:
> >
> > [PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control
> > [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS
> setup
> > [PATCH/RFC 3/3] ARM: S5PV210: Add a platform helper for MIPI DSIM/CSIS
> setup
> >
> 
> Any comments on this one?
> 
Hi,

It's 38 merge window now. So I want to wait until after this merge window.

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

RE: [PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> The phy_enable callback in struct s5p_platform_mipi_csis is added
> to allow the CSIS driver to control its PHY enable and reset signals.
> This allows to use same MIPI CSIS driver across various SoCs.
> 
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/plat-s5p/dev-csis0.c              |    2 +-
>  arch/arm/plat-s5p/dev-csis1.c              |    2 +-
>  arch/arm/plat-s5p/include/plat/csis.h      |   28 --------------------
>  arch/arm/plat-s5p/include/plat/mipi_csis.h |   39
> ++++++++++++++++++++++++++++
>  4 files changed, 41 insertions(+), 30 deletions(-)
>  delete mode 100644 arch/arm/plat-s5p/include/plat/csis.h
>  create mode 100644 arch/arm/plat-s5p/include/plat/mipi_csis.h
> 
> diff --git a/arch/arm/plat-s5p/dev-csis0.c b/arch/arm/plat-s5p/dev-csis0.c
> index dfab1c8..57efe9c 100644j
> --- a/arch/arm/plat-s5p/dev-csis0.c
> +++ b/arch/arm/plat-s5p/dev-csis0.c
> @@ -1,5 +1,5 @@
>  /*
> - * Copyright (C) 2010 Samsung Electronics
> + * Copyright (C) 2010 Samsung Electronics Co., Ltd
>   *
>   * S5P series device definition for MIPI-CSIS channel 0
>   *
> diff --git a/arch/arm/plat-s5p/dev-csis1.c b/arch/arm/plat-s5p/dev-csis1.c
> index e3053f2..c61b46b 100644
> --- a/arch/arm/plat-s5p/dev-csis1.c
> +++ b/arch/arm/plat-s5p/dev-csis1.c
> @@ -1,5 +1,5 @@
>  /*
> - * Copyright (C) 2010 Samsung Electronics
> + * Copyright (C) 2010 Samsung Electronics Co., Ltd
>   *
>   * S5P series device definition for MIPI-CSIS channel 1
>   *
> diff --git a/arch/arm/plat-s5p/include/plat/csis.h b/arch/arm/plat-
> s5p/include/plat/csis.h
> deleted file mode 100644
> index 51e308c..0000000
> --- a/arch/arm/plat-s5p/include/plat/csis.h
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -/*
> - * Copyright (C) 2010 Samsung Electronics
> - *
> - * S5P series MIPI CSI slave device support
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 as
> - * published by the Free Software Foundation.
> - */
> -
> -#ifndef PLAT_S5P_CSIS_H_
> -#define PLAT_S5P_CSIS_H_ __FILE__
> -
> -/**
> - * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
> - * @clk_rate: bus clock frequency
> - * @lanes: number of data lanes used
> - * @alignment: data alignment in bits
> - * @hs_settle: HS-RX settle time
> - */
> -struct s5p_platform_mipi_csis {
> -	unsigned long clk_rate;
> -	u8 lanes;
> -	u8 alignment;
> -	u8 hs_settle;
> -};
> -
> -#endif /* PLAT_S5P_CSIS_H_ */
> diff --git a/arch/arm/plat-s5p/include/plat/mipi_csis.h b/arch/arm/plat-
> s5p/include/plat/mipi_csis.h
> new file mode 100644
> index 0000000..0b22065
> --- /dev/null
> +++ b/arch/arm/plat-s5p/include/plat/mipi_csis.h
> @@ -0,0 +1,39 @@
> +/*
> + * Copyright (C) 2010 Samsung Electronics, Co. Ltd
> + *
> + * S5P series MIPI CSI slave device support
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef PLAT_S5P_MIPI_CSIS_H_
> +#define PLAT_S5P_MIPI_CSIS_H_ __FILE__
> +
> +struct platform_device;
> +
> +/**
> + * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
> + * @clk_rate: bus clock frequency
> + * @lanes: number of data lanes used
> + * @alignment: data alignment in bits
> + * @hs_settle: HS-RX settle time
> + */
> +struct s5p_platform_mipi_csis {
> +	unsigned long clk_rate;
> +	u8 lanes;
> +	u8 alignment;
> +	u8 hs_settle;
> +	int (*phy_enable)(struct platform_device *pdev, bool on);
> +};
> +
> +/**
> + * struct s5p_csis_phy_control - global MIPI-CSIS PHY control
> + * @pdev: platform device the mipi phy state is to be changed for
> + * @on: true to enable CSIS PHY and assert its reset,
> + *	false will disable the PHY and put into reset state
> + */
> +int s5p_csis_phy_enable(struct platform_device *pdev, bool on);
> +
> +#endif /* PLAT_S5P_MIPI_CSIS_H_ */
> --
> 1.7.3.4

I think should be separated like following.

If required, ...

1. change copyright
2. rename csis.h to mipi_csis.h
3. add phy enable feature

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

[PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> The phy_enable callback in struct s5p_platform_mipi_csis is added
> to allow the CSIS driver to control its PHY enable and reset signals.
> This allows to use same MIPI CSIS driver across various SoCs.
> 
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/plat-s5p/dev-csis0.c              |    2 +-
>  arch/arm/plat-s5p/dev-csis1.c              |    2 +-
>  arch/arm/plat-s5p/include/plat/csis.h      |   28 --------------------
>  arch/arm/plat-s5p/include/plat/mipi_csis.h |   39
> ++++++++++++++++++++++++++++
>  4 files changed, 41 insertions(+), 30 deletions(-)
>  delete mode 100644 arch/arm/plat-s5p/include/plat/csis.h
>  create mode 100644 arch/arm/plat-s5p/include/plat/mipi_csis.h
> 
> diff --git a/arch/arm/plat-s5p/dev-csis0.c b/arch/arm/plat-s5p/dev-csis0.c
> index dfab1c8..57efe9c 100644j
> --- a/arch/arm/plat-s5p/dev-csis0.c
> +++ b/arch/arm/plat-s5p/dev-csis0.c
> @@ -1,5 +1,5 @@
>  /*
> - * Copyright (C) 2010 Samsung Electronics
> + * Copyright (C) 2010 Samsung Electronics Co., Ltd
>   *
>   * S5P series device definition for MIPI-CSIS channel 0
>   *
> diff --git a/arch/arm/plat-s5p/dev-csis1.c b/arch/arm/plat-s5p/dev-csis1.c
> index e3053f2..c61b46b 100644
> --- a/arch/arm/plat-s5p/dev-csis1.c
> +++ b/arch/arm/plat-s5p/dev-csis1.c
> @@ -1,5 +1,5 @@
>  /*
> - * Copyright (C) 2010 Samsung Electronics
> + * Copyright (C) 2010 Samsung Electronics Co., Ltd
>   *
>   * S5P series device definition for MIPI-CSIS channel 1
>   *
> diff --git a/arch/arm/plat-s5p/include/plat/csis.h b/arch/arm/plat-
> s5p/include/plat/csis.h
> deleted file mode 100644
> index 51e308c..0000000
> --- a/arch/arm/plat-s5p/include/plat/csis.h
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -/*
> - * Copyright (C) 2010 Samsung Electronics
> - *
> - * S5P series MIPI CSI slave device support
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 as
> - * published by the Free Software Foundation.
> - */
> -
> -#ifndef PLAT_S5P_CSIS_H_
> -#define PLAT_S5P_CSIS_H_ __FILE__
> -
> -/**
> - * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
> - * @clk_rate: bus clock frequency
> - * @lanes: number of data lanes used
> - * @alignment: data alignment in bits
> - * @hs_settle: HS-RX settle time
> - */
> -struct s5p_platform_mipi_csis {
> -	unsigned long clk_rate;
> -	u8 lanes;
> -	u8 alignment;
> -	u8 hs_settle;
> -};
> -
> -#endif /* PLAT_S5P_CSIS_H_ */
> diff --git a/arch/arm/plat-s5p/include/plat/mipi_csis.h b/arch/arm/plat-
> s5p/include/plat/mipi_csis.h
> new file mode 100644
> index 0000000..0b22065
> --- /dev/null
> +++ b/arch/arm/plat-s5p/include/plat/mipi_csis.h
> @@ -0,0 +1,39 @@
> +/*
> + * Copyright (C) 2010 Samsung Electronics, Co. Ltd
> + *
> + * S5P series MIPI CSI slave device support
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef PLAT_S5P_MIPI_CSIS_H_
> +#define PLAT_S5P_MIPI_CSIS_H_ __FILE__
> +
> +struct platform_device;
> +
> +/**
> + * struct s5p_platform_mipi_csis - platform data for MIPI-CSIS
> + * @clk_rate: bus clock frequency
> + * @lanes: number of data lanes used
> + * @alignment: data alignment in bits
> + * @hs_settle: HS-RX settle time
> + */
> +struct s5p_platform_mipi_csis {
> +	unsigned long clk_rate;
> +	u8 lanes;
> +	u8 alignment;
> +	u8 hs_settle;
> +	int (*phy_enable)(struct platform_device *pdev, bool on);
> +};
> +
> +/**
> + * struct s5p_csis_phy_control - global MIPI-CSIS PHY control
> + * @pdev: platform device the mipi phy state is to be changed for
> + * @on: true to enable CSIS PHY and assert its reset,
> + *	false will disable the PHY and put into reset state
> + */
> +int s5p_csis_phy_enable(struct platform_device *pdev, bool on);
> +
> +#endif /* PLAT_S5P_MIPI_CSIS_H_ */
> --
> 1.7.3.4

I think should be separated like following.

If required, ...

1. change copyright
2. rename csis.h to mipi_csis.h
3. add phy enable feature

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

RE: [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
> and MIPI CSIS drivers so a spinlock is used to protect multiple
> access to these registers. Also a proper state of a common
> PHY enable bit is maintained in order to avoid a DSIM
> and CSIS driver conflict.
> 
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/mach-s5pv310/Kconfig                 |    6 ++
>  arch/arm/mach-s5pv310/Makefile                |    2 +
>  arch/arm/mach-s5pv310/include/mach/map.h      |    7 +--
>  arch/arm/mach-s5pv310/include/mach/regs-pmu.h |    6 ++
>  arch/arm/mach-s5pv310/setup-mipi.c            |   62
> +++++++++++++++++++++++++
>  5 files changed, 79 insertions(+), 4 deletions(-)
>  create mode 100644 arch/arm/mach-s5pv310/setup-mipi.c
> 
> diff --git a/arch/arm/mach-s5pv310/Kconfig b/arch/arm/mach-s5pv310/Kconfig
> index b7aa3cd..2420076 100644
> --- a/arch/arm/mach-s5pv310/Kconfig
> +++ b/arch/arm/mach-s5pv310/Kconfig
> @@ -15,6 +15,11 @@ config CPU_S5PV310
>  	help
>  	  Enable S5PV310 CPU support
> 
> +config S5PV310_SETUP_MIPI
> +	bool
> +	help
> +	  Common setup code for MIPI CSIS/DSIM channels 0 and 1.
> +
>  config S5PV310_DEV_PD
>  	bool
>  	help
> @@ -96,6 +101,7 @@ config MACH_UNIVERSAL_C210
>  	select S3C_DEV_HSMMC3
>  	select S5PV310_SETUP_SDHCI
>  	select S3C_DEV_I2C1
> +	select S5PV310_SETUP_MIPI
>  	select S5PV310_SETUP_I2C1
>  	help
>  	  Machine support for Samsung Mobile Universal S5PC210 Reference
> diff --git a/arch/arm/mach-s5pv310/Makefile
b/arch/arm/mach-s5pv310/Makefile
> index 651f193..7f1b89b 100644
> --- a/arch/arm/mach-s5pv310/Makefile
> +++ b/arch/arm/mach-s5pv310/Makefile
> @@ -29,6 +29,8 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+=
mach-universal_c210.o
>  # device support
> 
>  obj-y					+= dev-audio.o
> +
> +obj-$(CONFIG_S5PV310_SETUP_MIPI)	+= setup-mipi.o
>  obj-$(CONFIG_S5PV310_DEV_PD)		+= dev-pd.o
> 
>  obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
> diff --git a/arch/arm/mach-s5pv310/include/mach/map.h b/arch/arm/mach-
> s5pv310/include/mach/map.h
> index 33bcff2..6635287 100644
> --- a/arch/arm/mach-s5pv310/include/mach/map.h
> +++ b/arch/arm/mach-s5pv310/include/mach/map.h
> @@ -65,8 +65,7 @@
>  #define S5PV310_PA_GPIO2		(0x11000000)
>  #define S5PV310_PA_GPIO3		(0x03860000)
> 
> -#define S5PV310_PA_MIPI_CSIS0		0x11880000
> -#define S5PV310_PA_MIPI_CSIS1		0x11890000
> +#define S5PV310_PA_MIPI_CSIS(x)		(0x11880000 + ((x) *
0x10000))
> 
>  #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
> 
> @@ -124,7 +123,7 @@
>  #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
>  #define S3C_PA_RTC			S5PV310_PA_RTC
>  #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
> -#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
> -#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
> +#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS(0)
> +#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS(1)
> 
>  #endif /* __ASM_ARCH_MAP_H */
> diff --git a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
b/arch/arm/mach-
> s5pv310/include/mach/regs-pmu.h
> index fb333d0..bef8102 100644
> --- a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
> +++ b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
> @@ -27,4 +27,10 @@
> 
>  #define S5P_INT_LOCAL_PWR_EN		0x7
> 
> +#define S5P_MIPI_PHY0_CONTROL		S5P_PMUREG(0x0710)
> +#define S5P_MIPI_PHY1_CONTROL		S5P_PMUREG(0x0714)
> +#define S5P_MIPI_PHY_ENABLE		(1 << 0)
> +#define S5P_MIPI_PHY_SRESETN		(1 << 1)
> +#define S5P_MIPI_PHY_MRESETN		(1 << 2)
> +
>  #endif /* __ASM_ARCH_REGS_PMU_H */
> diff --git a/arch/arm/mach-s5pv310/setup-mipi.c b/arch/arm/mach-
> s5pv310/setup-mipi.c
> new file mode 100644
> index 0000000..fc91a29
> --- /dev/null
> +++ b/arch/arm/mach-s5pv310/setup-mipi.c
> @@ -0,0 +1,62 @@
> +/* linux/arch/arm/mach-s5pv310/setup-mipi.c
> + *
> + * Copyright (c) 2010 Samsung Electronics Co., Ltd
> + *
> + * S5PV310 - Helper functions for MIPI CSIS/DSIM PHY control
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/spinlock.h>
> +#include <mach/regs-pmu.h>
> +
> +/* Global MIPI CSIS or DSIM PHY enable and reset control. */
> +static int s5p_mipi_phy_control(struct platform_device *pdev, bool on,
u32
> rst)
> +{
> +	static DEFINE_SPINLOCK(lock);
> +	void __iomem *addr;
> +	unsigned long flags;
> +	int pid;
> +	u32 cfg;
> +
> +	if (pdev == NULL)
> +		return -EINVAL;
> +
> +	pid = pdev->id;
> +	if (pid != 0 && pid != 1)
> +		return -EINVAL;
> +
> +	addr = pid ? S5P_MIPI_PHY1_CONTROL : S5P_MIPI_PHY0_CONTROL;
> +
> +	spin_lock_irqsave(&lock, flags);
> +
> +	cfg = __raw_readl(addr) & ~rst;
> +	if (on)
> +		cfg |= rst;
> +	__raw_writel(cfg, addr);
> +
> +	if (on)
> +		cfg |= S5P_MIPI_PHY_ENABLE;
> +	else if (!(cfg & (S5P_MIPI_PHY_SRESETN | S5P_MIPI_PHY_MRESETN) &
~rst))
> +		cfg &= ~S5P_MIPI_PHY_ENABLE;
> +
> +	__raw_writel(cfg, addr);
> +
> +	spin_unlock_irqrestore(&lock, flags);
> +	return 0;
> +}
> +
> +int s5p_csis_phy_enable(struct platform_device *pdev, bool on)
> +{
> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_SRESETN);
> +}
> +
> +int s5p_dsim_phy_enable(struct platform_device *pdev, bool on)
> +{
> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_MRESETN);
> +}
> --
> 1.7.3.4

Basically, it's not good that each machine(SoC) has each own setup-mipi...
Because it is very similar(almost same)...means can move it in plat-s5p with
following.

1. # of MIPI PHY can be calculated by platform device id
2. can use same definition of MIPI PHY control address with same name
re-mapping.

And hmm...need to re-think about this after this merge window...

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
> and MIPI CSIS drivers so a spinlock is used to protect multiple
> access to these registers. Also a proper state of a common
> PHY enable bit is maintained in order to avoid a DSIM
> and CSIS driver conflict.
> 
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/mach-s5pv310/Kconfig                 |    6 ++
>  arch/arm/mach-s5pv310/Makefile                |    2 +
>  arch/arm/mach-s5pv310/include/mach/map.h      |    7 +--
>  arch/arm/mach-s5pv310/include/mach/regs-pmu.h |    6 ++
>  arch/arm/mach-s5pv310/setup-mipi.c            |   62
> +++++++++++++++++++++++++
>  5 files changed, 79 insertions(+), 4 deletions(-)
>  create mode 100644 arch/arm/mach-s5pv310/setup-mipi.c
> 
> diff --git a/arch/arm/mach-s5pv310/Kconfig b/arch/arm/mach-s5pv310/Kconfig
> index b7aa3cd..2420076 100644
> --- a/arch/arm/mach-s5pv310/Kconfig
> +++ b/arch/arm/mach-s5pv310/Kconfig
> @@ -15,6 +15,11 @@ config CPU_S5PV310
>  	help
>  	  Enable S5PV310 CPU support
> 
> +config S5PV310_SETUP_MIPI
> +	bool
> +	help
> +	  Common setup code for MIPI CSIS/DSIM channels 0 and 1.
> +
>  config S5PV310_DEV_PD
>  	bool
>  	help
> @@ -96,6 +101,7 @@ config MACH_UNIVERSAL_C210
>  	select S3C_DEV_HSMMC3
>  	select S5PV310_SETUP_SDHCI
>  	select S3C_DEV_I2C1
> +	select S5PV310_SETUP_MIPI
>  	select S5PV310_SETUP_I2C1
>  	help
>  	  Machine support for Samsung Mobile Universal S5PC210 Reference
> diff --git a/arch/arm/mach-s5pv310/Makefile
b/arch/arm/mach-s5pv310/Makefile
> index 651f193..7f1b89b 100644
> --- a/arch/arm/mach-s5pv310/Makefile
> +++ b/arch/arm/mach-s5pv310/Makefile
> @@ -29,6 +29,8 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+=
mach-universal_c210.o
>  # device support
> 
>  obj-y					+= dev-audio.o
> +
> +obj-$(CONFIG_S5PV310_SETUP_MIPI)	+= setup-mipi.o
>  obj-$(CONFIG_S5PV310_DEV_PD)		+= dev-pd.o
> 
>  obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
> diff --git a/arch/arm/mach-s5pv310/include/mach/map.h b/arch/arm/mach-
> s5pv310/include/mach/map.h
> index 33bcff2..6635287 100644
> --- a/arch/arm/mach-s5pv310/include/mach/map.h
> +++ b/arch/arm/mach-s5pv310/include/mach/map.h
> @@ -65,8 +65,7 @@
>  #define S5PV310_PA_GPIO2		(0x11000000)
>  #define S5PV310_PA_GPIO3		(0x03860000)
> 
> -#define S5PV310_PA_MIPI_CSIS0		0x11880000
> -#define S5PV310_PA_MIPI_CSIS1		0x11890000
> +#define S5PV310_PA_MIPI_CSIS(x)		(0x11880000 + ((x) *
0x10000))
> 
>  #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
> 
> @@ -124,7 +123,7 @@
>  #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
>  #define S3C_PA_RTC			S5PV310_PA_RTC
>  #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
> -#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
> -#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
> +#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS(0)
> +#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS(1)
> 
>  #endif /* __ASM_ARCH_MAP_H */
> diff --git a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
b/arch/arm/mach-
> s5pv310/include/mach/regs-pmu.h
> index fb333d0..bef8102 100644
> --- a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
> +++ b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
> @@ -27,4 +27,10 @@
> 
>  #define S5P_INT_LOCAL_PWR_EN		0x7
> 
> +#define S5P_MIPI_PHY0_CONTROL		S5P_PMUREG(0x0710)
> +#define S5P_MIPI_PHY1_CONTROL		S5P_PMUREG(0x0714)
> +#define S5P_MIPI_PHY_ENABLE		(1 << 0)
> +#define S5P_MIPI_PHY_SRESETN		(1 << 1)
> +#define S5P_MIPI_PHY_MRESETN		(1 << 2)
> +
>  #endif /* __ASM_ARCH_REGS_PMU_H */
> diff --git a/arch/arm/mach-s5pv310/setup-mipi.c b/arch/arm/mach-
> s5pv310/setup-mipi.c
> new file mode 100644
> index 0000000..fc91a29
> --- /dev/null
> +++ b/arch/arm/mach-s5pv310/setup-mipi.c
> @@ -0,0 +1,62 @@
> +/* linux/arch/arm/mach-s5pv310/setup-mipi.c
> + *
> + * Copyright (c) 2010 Samsung Electronics Co., Ltd
> + *
> + * S5PV310 - Helper functions for MIPI CSIS/DSIM PHY control
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/spinlock.h>
> +#include <mach/regs-pmu.h>
> +
> +/* Global MIPI CSIS or DSIM PHY enable and reset control. */
> +static int s5p_mipi_phy_control(struct platform_device *pdev, bool on,
u32
> rst)
> +{
> +	static DEFINE_SPINLOCK(lock);
> +	void __iomem *addr;
> +	unsigned long flags;
> +	int pid;
> +	u32 cfg;
> +
> +	if (pdev == NULL)
> +		return -EINVAL;
> +
> +	pid = pdev->id;
> +	if (pid != 0 && pid != 1)
> +		return -EINVAL;
> +
> +	addr = pid ? S5P_MIPI_PHY1_CONTROL : S5P_MIPI_PHY0_CONTROL;
> +
> +	spin_lock_irqsave(&lock, flags);
> +
> +	cfg = __raw_readl(addr) & ~rst;
> +	if (on)
> +		cfg |= rst;
> +	__raw_writel(cfg, addr);
> +
> +	if (on)
> +		cfg |= S5P_MIPI_PHY_ENABLE;
> +	else if (!(cfg & (S5P_MIPI_PHY_SRESETN | S5P_MIPI_PHY_MRESETN) &
~rst))
> +		cfg &= ~S5P_MIPI_PHY_ENABLE;
> +
> +	__raw_writel(cfg, addr);
> +
> +	spin_unlock_irqrestore(&lock, flags);
> +	return 0;
> +}
> +
> +int s5p_csis_phy_enable(struct platform_device *pdev, bool on)
> +{
> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_SRESETN);
> +}
> +
> +int s5p_dsim_phy_enable(struct platform_device *pdev, bool on)
> +{
> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_MRESETN);
> +}
> --
> 1.7.3.4

Basically, it's not good that each machine(SoC) has each own setup-mipi...
Because it is very similar(almost same)...means can move it in plat-s5p with
following.

1. # of MIPI PHY can be calculated by platform device id
2. can use same definition of MIPI PHY control address with same name
re-mapping.

And hmm...need to re-think about this after this merge window...

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

Re: [PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control

[Sylwester Nawrocki]

Hi Kukjin,

thank you for the update.

On 01/13/2011 10:29 AM, Kukjin Kim wrote:
> Sylwester Nawrocki wrote:
>>
>> The phy_enable callback in struct s5p_platform_mipi_csis is added
>> to allow the CSIS driver to control its PHY enable and reset signals.
>> This allows to use same MIPI CSIS driver across various SoCs.
>>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>>  arch/arm/plat-s5p/dev-csis0.c              |    2 +-
>>  arch/arm/plat-s5p/dev-csis1.c              |    2 +-
>>  arch/arm/plat-s5p/include/plat/csis.h      |   28 --------------------
>>  arch/arm/plat-s5p/include/plat/mipi_csis.h |   39
>> ++++++++++++++++++++++++++++
>>  4 files changed, 41 insertions(+), 30 deletions(-)
>>  delete mode 100644 arch/arm/plat-s5p/include/plat/csis.h
>>  create mode 100644 arch/arm/plat-s5p/include/plat/mipi_csis.h
>>
...
> 
> I think should be separated like following.
> 
> If required, ...
> 
> 1. change copyright
> 2. rename csis.h to mipi_csis.h

I don't want to bother with a separate patches for that, just prefer
to drop the above changes.

> 3. add phy enable feature

OK, I would reduce the patch to that change only.

Regards,
-- 
Sylwester Nawrocki
Samsung Poland R&D Center

[PATCH/RFC 1/3] ARM: S5P: Add a platform callback for MIPI CSIS PHY control

[Sylwester Nawrocki]

Hi Kukjin,

thank you for the update.

On 01/13/2011 10:29 AM, Kukjin Kim wrote:
> Sylwester Nawrocki wrote:
>>
>> The phy_enable callback in struct s5p_platform_mipi_csis is added
>> to allow the CSIS driver to control its PHY enable and reset signals.
>> This allows to use same MIPI CSIS driver across various SoCs.
>>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>>  arch/arm/plat-s5p/dev-csis0.c              |    2 +-
>>  arch/arm/plat-s5p/dev-csis1.c              |    2 +-
>>  arch/arm/plat-s5p/include/plat/csis.h      |   28 --------------------
>>  arch/arm/plat-s5p/include/plat/mipi_csis.h |   39
>> ++++++++++++++++++++++++++++
>>  4 files changed, 41 insertions(+), 30 deletions(-)
>>  delete mode 100644 arch/arm/plat-s5p/include/plat/csis.h
>>  create mode 100644 arch/arm/plat-s5p/include/plat/mipi_csis.h
>>
...
> 
> I think should be separated like following.
> 
> If required, ...
> 
> 1. change copyright
> 2. rename csis.h to mipi_csis.h

I don't want to bother with a separate patches for that, just prefer
to drop the above changes.

> 3. add phy enable feature

OK, I would reduce the patch to that change only.

Regards,
-- 
Sylwester Nawrocki
Samsung Poland R&D Center

Re: [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

On 01/13/2011 10:33 AM, Kukjin Kim wrote:
> Sylwester Nawrocki wrote:
>>
>> MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
>> and MIPI CSIS drivers so a spinlock is used to protect multiple
>> access to these registers. Also a proper state of a common
>> PHY enable bit is maintained in order to avoid a DSIM
>> and CSIS driver conflict.
>>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
...
> 
> Basically, it's not good that each machine(SoC) has each own setup-mipi...
> Because it is very similar(almost same)...means can move it in plat-s5p with
> following. 
> 
> 1. # of MIPI PHY can be calculated by platform device id
> 2. can use same definition of MIPI PHY control address with same name
> re-mapping.

Yes, I agree with that. Originally I had it done it plat-s5p, I will
prepare a merged version. The main difference between s5pv210 and s5pv310
indeed was the register naming and placement in PMU or CLK subsystem, so the
register  address definitions were in regs-clk.h or regs-pmu.h. So there 
just will have to be included different header files depending on on SoC 
architecture.


Regards,
-- 
Sylwester Nawrocki
Samsung Poland R&D Center

[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

On 01/13/2011 10:33 AM, Kukjin Kim wrote:
> Sylwester Nawrocki wrote:
>>
>> MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
>> and MIPI CSIS drivers so a spinlock is used to protect multiple
>> access to these registers. Also a proper state of a common
>> PHY enable bit is maintained in order to avoid a DSIM
>> and CSIS driver conflict.
>>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
...
> 
> Basically, it's not good that each machine(SoC) has each own setup-mipi...
> Because it is very similar(almost same)...means can move it in plat-s5p with
> following. 
> 
> 1. # of MIPI PHY can be calculated by platform device id
> 2. can use same definition of MIPI PHY control address with same name
> re-mapping.

Yes, I agree with that. Originally I had it done it plat-s5p, I will
prepare a merged version. The main difference between s5pv210 and s5pv310
indeed was the register naming and placement in PMU or CLK subsystem, so the
register  address definitions were in regs-clk.h or regs-pmu.h. So there 
just will have to be included different header files depending on on SoC 
architecture.


Regards,
-- 
Sylwester Nawrocki
Samsung Poland R&D Center

Re: [PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

Hello,

On 01/13/2011 02:33 AM, Kukjin Kim wrote:
> Sylwester Nawrocki wrote:
>>
>> MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
>> and MIPI CSIS drivers so a spinlock is used to protect multiple
>> access to these registers. Also a proper state of a common
>> PHY enable bit is maintained in order to avoid a DSIM
>> and CSIS driver conflict.
>>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>>  arch/arm/mach-s5pv310/Kconfig                 |    6 ++
>>  arch/arm/mach-s5pv310/Makefile                |    2 +
>>  arch/arm/mach-s5pv310/include/mach/map.h      |    7 +--
>>  arch/arm/mach-s5pv310/include/mach/regs-pmu.h |    6 ++
>>  arch/arm/mach-s5pv310/setup-mipi.c            |   62
>> +++++++++++++++++++++++++
>>  5 files changed, 79 insertions(+), 4 deletions(-)
>>  create mode 100644 arch/arm/mach-s5pv310/setup-mipi.c
>>
>> diff --git a/arch/arm/mach-s5pv310/Kconfig b/arch/arm/mach-s5pv310/Kconfig
>> index b7aa3cd..2420076 100644
>> --- a/arch/arm/mach-s5pv310/Kconfig
>> +++ b/arch/arm/mach-s5pv310/Kconfig
>> @@ -15,6 +15,11 @@ config CPU_S5PV310
>>  	help
>>  	  Enable S5PV310 CPU support
>>
>> +config S5PV310_SETUP_MIPI
>> +	bool
>> +	help
>> +	  Common setup code for MIPI CSIS/DSIM channels 0 and 1.
>> +
>>  config S5PV310_DEV_PD
>>  	bool
>>  	help
>> @@ -96,6 +101,7 @@ config MACH_UNIVERSAL_C210
>>  	select S3C_DEV_HSMMC3
>>  	select S5PV310_SETUP_SDHCI
>>  	select S3C_DEV_I2C1
>> +	select S5PV310_SETUP_MIPI
>>  	select S5PV310_SETUP_I2C1
>>  	help
>>  	  Machine support for Samsung Mobile Universal S5PC210 Reference
>> diff --git a/arch/arm/mach-s5pv310/Makefile
> b/arch/arm/mach-s5pv310/Makefile
>> index 651f193..7f1b89b 100644
>> --- a/arch/arm/mach-s5pv310/Makefile
>> +++ b/arch/arm/mach-s5pv310/Makefile
>> @@ -29,6 +29,8 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+=
> mach-universal_c210.o
>>  # device support
>>
>>  obj-y					+= dev-audio.o
>> +
>> +obj-$(CONFIG_S5PV310_SETUP_MIPI)	+= setup-mipi.o
>>  obj-$(CONFIG_S5PV310_DEV_PD)		+= dev-pd.o
>>
>>  obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
>> diff --git a/arch/arm/mach-s5pv310/include/mach/map.h b/arch/arm/mach-
>> s5pv310/include/mach/map.h
>> index 33bcff2..6635287 100644
>> --- a/arch/arm/mach-s5pv310/include/mach/map.h
>> +++ b/arch/arm/mach-s5pv310/include/mach/map.h
>> @@ -65,8 +65,7 @@
>>  #define S5PV310_PA_GPIO2		(0x11000000)
>>  #define S5PV310_PA_GPIO3		(0x03860000)
>>
>> -#define S5PV310_PA_MIPI_CSIS0		0x11880000
>> -#define S5PV310_PA_MIPI_CSIS1		0x11890000
>> +#define S5PV310_PA_MIPI_CSIS(x)		(0x11880000 + ((x) *
> 0x10000))
>>
>>  #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
>>
>> @@ -124,7 +123,7 @@
>>  #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
>>  #define S3C_PA_RTC			S5PV310_PA_RTC
>>  #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
>> -#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
>> -#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
>> +#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS(0)
>> +#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS(1)
>>
>>  #endif /* __ASM_ARCH_MAP_H */
>> diff --git a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
> b/arch/arm/mach-
>> s5pv310/include/mach/regs-pmu.h
>> index fb333d0..bef8102 100644
>> --- a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
>> +++ b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
>> @@ -27,4 +27,10 @@
>>
>>  #define S5P_INT_LOCAL_PWR_EN		0x7
>>
>> +#define S5P_MIPI_PHY0_CONTROL		S5P_PMUREG(0x0710)
>> +#define S5P_MIPI_PHY1_CONTROL		S5P_PMUREG(0x0714)
>> +#define S5P_MIPI_PHY_ENABLE		(1 << 0)
>> +#define S5P_MIPI_PHY_SRESETN		(1 << 1)
>> +#define S5P_MIPI_PHY_MRESETN		(1 << 2)
>> +
>>  #endif /* __ASM_ARCH_REGS_PMU_H */
>> diff --git a/arch/arm/mach-s5pv310/setup-mipi.c b/arch/arm/mach-
>> s5pv310/setup-mipi.c
>> new file mode 100644
>> index 0000000..fc91a29
>> --- /dev/null
>> +++ b/arch/arm/mach-s5pv310/setup-mipi.c
>> @@ -0,0 +1,62 @@
>> +/* linux/arch/arm/mach-s5pv310/setup-mipi.c
>> + *
>> + * Copyright (c) 2010 Samsung Electronics Co., Ltd
>> + *
>> + * S5PV310 - Helper functions for MIPI CSIS/DSIM PHY control
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/io.h>
>> +#include <linux/spinlock.h>
>> +#include <mach/regs-pmu.h>
>> +
>> +/* Global MIPI CSIS or DSIM PHY enable and reset control. */
>> +static int s5p_mipi_phy_control(struct platform_device *pdev, bool on,
> u32
>> rst)
>> +{
>> +	static DEFINE_SPINLOCK(lock);
>> +	void __iomem *addr;
>> +	unsigned long flags;
>> +	int pid;
>> +	u32 cfg;
>> +
>> +	if (pdev == NULL)
>> +		return -EINVAL;
>> +
>> +	pid = pdev->id;
>> +	if (pid != 0 && pid != 1)
>> +		return -EINVAL;
>> +
>> +	addr = pid ? S5P_MIPI_PHY1_CONTROL : S5P_MIPI_PHY0_CONTROL;
>> +
>> +	spin_lock_irqsave(&lock, flags);
>> +
>> +	cfg = __raw_readl(addr) & ~rst;
>> +	if (on)
>> +		cfg |= rst;
>> +	__raw_writel(cfg, addr);
>> +
>> +	if (on)
>> +		cfg |= S5P_MIPI_PHY_ENABLE;
>> +	else if (!(cfg & (S5P_MIPI_PHY_SRESETN | S5P_MIPI_PHY_MRESETN) &
> ~rst))
>> +		cfg &= ~S5P_MIPI_PHY_ENABLE;
>> +
>> +	__raw_writel(cfg, addr);
>> +
>> +	spin_unlock_irqrestore(&lock, flags);
>> +	return 0;
>> +}
>> +
>> +int s5p_csis_phy_enable(struct platform_device *pdev, bool on)
>> +{
>> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_SRESETN);
>> +}
>> +
>> +int s5p_dsim_phy_enable(struct platform_device *pdev, bool on)
>> +{
>> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_MRESETN);
>> +}
>> --
>> 1.7.3.4
> 
> Basically, it's not good that each machine(SoC) has each own setup-mipi...
> Because it is very similar(almost same)...means can move it in plat-s5p with
> following.
>
> 1. # of MIPI PHY can be calculated by platform device id
> 2. can use same definition of MIPI PHY control address with same name
> re-mapping.
> 

There one serious problem with that approach though, we cannot make a common
kernel binary for multiple archs. When each mach-s5p* has it's own setup code
the is no issue as those files would be compiled with their respective headers.
How do we solve that problem with common code in plat-s5p? Any comments, ideas?

Regards,
Sylwester








-- 
Sylwester Nawrocki
Samsung Poland R&D Center

[PATCH/RFC 2/3] ARM: S5PV310: Add a platform helper for MIPI DSIM/CSIS setup

[Sylwester Nawrocki]

Hello,

On 01/13/2011 02:33 AM, Kukjin Kim wrote:
> Sylwester Nawrocki wrote:
>>
>> MIPI_PHYn_CONTROL registers are shared between MIPI DSIM
>> and MIPI CSIS drivers so a spinlock is used to protect multiple
>> access to these registers. Also a proper state of a common
>> PHY enable bit is maintained in order to avoid a DSIM
>> and CSIS driver conflict.
>>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>>  arch/arm/mach-s5pv310/Kconfig                 |    6 ++
>>  arch/arm/mach-s5pv310/Makefile                |    2 +
>>  arch/arm/mach-s5pv310/include/mach/map.h      |    7 +--
>>  arch/arm/mach-s5pv310/include/mach/regs-pmu.h |    6 ++
>>  arch/arm/mach-s5pv310/setup-mipi.c            |   62
>> +++++++++++++++++++++++++
>>  5 files changed, 79 insertions(+), 4 deletions(-)
>>  create mode 100644 arch/arm/mach-s5pv310/setup-mipi.c
>>
>> diff --git a/arch/arm/mach-s5pv310/Kconfig b/arch/arm/mach-s5pv310/Kconfig
>> index b7aa3cd..2420076 100644
>> --- a/arch/arm/mach-s5pv310/Kconfig
>> +++ b/arch/arm/mach-s5pv310/Kconfig
>> @@ -15,6 +15,11 @@ config CPU_S5PV310
>>  	help
>>  	  Enable S5PV310 CPU support
>>
>> +config S5PV310_SETUP_MIPI
>> +	bool
>> +	help
>> +	  Common setup code for MIPI CSIS/DSIM channels 0 and 1.
>> +
>>  config S5PV310_DEV_PD
>>  	bool
>>  	help
>> @@ -96,6 +101,7 @@ config MACH_UNIVERSAL_C210
>>  	select S3C_DEV_HSMMC3
>>  	select S5PV310_SETUP_SDHCI
>>  	select S3C_DEV_I2C1
>> +	select S5PV310_SETUP_MIPI
>>  	select S5PV310_SETUP_I2C1
>>  	help
>>  	  Machine support for Samsung Mobile Universal S5PC210 Reference
>> diff --git a/arch/arm/mach-s5pv310/Makefile
> b/arch/arm/mach-s5pv310/Makefile
>> index 651f193..7f1b89b 100644
>> --- a/arch/arm/mach-s5pv310/Makefile
>> +++ b/arch/arm/mach-s5pv310/Makefile
>> @@ -29,6 +29,8 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+=
> mach-universal_c210.o
>>  # device support
>>
>>  obj-y					+= dev-audio.o
>> +
>> +obj-$(CONFIG_S5PV310_SETUP_MIPI)	+= setup-mipi.o
>>  obj-$(CONFIG_S5PV310_DEV_PD)		+= dev-pd.o
>>
>>  obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
>> diff --git a/arch/arm/mach-s5pv310/include/mach/map.h b/arch/arm/mach-
>> s5pv310/include/mach/map.h
>> index 33bcff2..6635287 100644
>> --- a/arch/arm/mach-s5pv310/include/mach/map.h
>> +++ b/arch/arm/mach-s5pv310/include/mach/map.h
>> @@ -65,8 +65,7 @@
>>  #define S5PV310_PA_GPIO2		(0x11000000)
>>  #define S5PV310_PA_GPIO3		(0x03860000)
>>
>> -#define S5PV310_PA_MIPI_CSIS0		0x11880000
>> -#define S5PV310_PA_MIPI_CSIS1		0x11890000
>> +#define S5PV310_PA_MIPI_CSIS(x)		(0x11880000 + ((x) *
> 0x10000))
>>
>>  #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
>>
>> @@ -124,7 +123,7 @@
>>  #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
>>  #define S3C_PA_RTC			S5PV310_PA_RTC
>>  #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
>> -#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
>> -#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
>> +#define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS(0)
>> +#define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS(1)
>>
>>  #endif /* __ASM_ARCH_MAP_H */
>> diff --git a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
> b/arch/arm/mach-
>> s5pv310/include/mach/regs-pmu.h
>> index fb333d0..bef8102 100644
>> --- a/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
>> +++ b/arch/arm/mach-s5pv310/include/mach/regs-pmu.h
>> @@ -27,4 +27,10 @@
>>
>>  #define S5P_INT_LOCAL_PWR_EN		0x7
>>
>> +#define S5P_MIPI_PHY0_CONTROL		S5P_PMUREG(0x0710)
>> +#define S5P_MIPI_PHY1_CONTROL		S5P_PMUREG(0x0714)
>> +#define S5P_MIPI_PHY_ENABLE		(1 << 0)
>> +#define S5P_MIPI_PHY_SRESETN		(1 << 1)
>> +#define S5P_MIPI_PHY_MRESETN		(1 << 2)
>> +
>>  #endif /* __ASM_ARCH_REGS_PMU_H */
>> diff --git a/arch/arm/mach-s5pv310/setup-mipi.c b/arch/arm/mach-
>> s5pv310/setup-mipi.c
>> new file mode 100644
>> index 0000000..fc91a29
>> --- /dev/null
>> +++ b/arch/arm/mach-s5pv310/setup-mipi.c
>> @@ -0,0 +1,62 @@
>> +/* linux/arch/arm/mach-s5pv310/setup-mipi.c
>> + *
>> + * Copyright (c) 2010 Samsung Electronics Co., Ltd
>> + *
>> + * S5PV310 - Helper functions for MIPI CSIS/DSIM PHY control
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/io.h>
>> +#include <linux/spinlock.h>
>> +#include <mach/regs-pmu.h>
>> +
>> +/* Global MIPI CSIS or DSIM PHY enable and reset control. */
>> +static int s5p_mipi_phy_control(struct platform_device *pdev, bool on,
> u32
>> rst)
>> +{
>> +	static DEFINE_SPINLOCK(lock);
>> +	void __iomem *addr;
>> +	unsigned long flags;
>> +	int pid;
>> +	u32 cfg;
>> +
>> +	if (pdev == NULL)
>> +		return -EINVAL;
>> +
>> +	pid = pdev->id;
>> +	if (pid != 0 && pid != 1)
>> +		return -EINVAL;
>> +
>> +	addr = pid ? S5P_MIPI_PHY1_CONTROL : S5P_MIPI_PHY0_CONTROL;
>> +
>> +	spin_lock_irqsave(&lock, flags);
>> +
>> +	cfg = __raw_readl(addr) & ~rst;
>> +	if (on)
>> +		cfg |= rst;
>> +	__raw_writel(cfg, addr);
>> +
>> +	if (on)
>> +		cfg |= S5P_MIPI_PHY_ENABLE;
>> +	else if (!(cfg & (S5P_MIPI_PHY_SRESETN | S5P_MIPI_PHY_MRESETN) &
> ~rst))
>> +		cfg &= ~S5P_MIPI_PHY_ENABLE;
>> +
>> +	__raw_writel(cfg, addr);
>> +
>> +	spin_unlock_irqrestore(&lock, flags);
>> +	return 0;
>> +}
>> +
>> +int s5p_csis_phy_enable(struct platform_device *pdev, bool on)
>> +{
>> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_SRESETN);
>> +}
>> +
>> +int s5p_dsim_phy_enable(struct platform_device *pdev, bool on)
>> +{
>> +	return s5p_mipi_phy_control(pdev, on, S5P_MIPI_PHY_MRESETN);
>> +}
>> --
>> 1.7.3.4
> 
> Basically, it's not good that each machine(SoC) has each own setup-mipi...
> Because it is very similar(almost same)...means can move it in plat-s5p with
> following.
>
> 1. # of MIPI PHY can be calculated by platform device id
> 2. can use same definition of MIPI PHY control address with same name
> re-mapping.
> 

There one serious problem with that approach though, we cannot make a common
kernel binary for multiple archs. When each mach-s5p* has it's own setup code
the is no issue as those files would be compiled with their respective headers.
How do we solve that problem with common code in plat-s5p? Any comments, ideas?

Regards,
Sylwester








-- 
Sylwester Nawrocki
Samsung Poland R&D Center