All of lore.kernel.org
 help / color / mirror / Atom feed
* [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor
@ 2011-01-14 16:41 Kumar Gala
  2011-01-14 16:41 ` [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor Kumar Gala
                   ` (2 more replies)
  0 siblings, 3 replies; 7+ messages in thread
From: Kumar Gala @ 2011-01-14 16:41 UTC (permalink / raw)
  To: u-boot

From: Poonam Aggrwal <poonam.aggrwal@freescale.com>

Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
	* TCP/IP acceleration and classification capabilities
	* IEEE 1588 support
	* Lossless flow control
	* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
  up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
  software watchdog timer, and four general-purpose timers
* Dual DUARTs

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/cpu/mpc85xx/Makefile    |    1 +
 arch/powerpc/cpu/mpc8xxx/cpu.c       |    2 ++
 arch/powerpc/include/asm/config.h    |    6 ++++--
 arch/powerpc/include/asm/processor.h |    2 ++
 drivers/misc/fsl_law.c               |    1 +
 5 files changed, 10 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile
index af7bc09..e1261cf 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -50,6 +50,7 @@ COBJS-$(CONFIG_MPC8544) += ddr-gen2.o
 COBJS-$(CONFIG_MPC8572) += ddr-gen3.o
 COBJS-$(CONFIG_MPC8536) += ddr-gen3.o
 COBJS-$(CONFIG_MPC8569)	+= ddr-gen3.o
+COBJS-$(CONFIG_P1010)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1011)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1012)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1013)	+= ddr-gen3.o
diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
index 5b30fbd..ac720a5 100644
--- a/arch/powerpc/cpu/mpc8xxx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
@@ -64,6 +64,8 @@ struct cpu_type cpu_type_list [] = {
 	CPU_TYPE_ENTRY(8569, 8569_E, 1),
 	CPU_TYPE_ENTRY(8572, 8572, 2),
 	CPU_TYPE_ENTRY(8572, 8572_E, 2),
+	CPU_TYPE_ENTRY(P1010, P1010, 1),
+	CPU_TYPE_ENTRY(P1010, P1010_E, 1),
 	CPU_TYPE_ENTRY(P1011, P1011, 1),
 	CPU_TYPE_ENTRY(P1011, P1011_E, 1),
 	CPU_TYPE_ENTRY(P1012, P1012, 1),
diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h
index 76dedeb..d80fc97 100644
--- a/arch/powerpc/include/asm/config.h
+++ b/arch/powerpc/include/asm/config.h
@@ -69,14 +69,16 @@
 
 /* Enable TSEC2.0 for the platforms that have it if we are using TSEC */
 #if defined(CONFIG_TSEC_ENET) && \
-    (defined(CONFIG_P1020) || defined(CONFIG_P1011))
+    (defined(CONFIG_P1010) || \
+     defined(CONFIG_P1020) || defined(CONFIG_P1011))
 #define CONFIG_TSECV2
 #endif
 
 /*
  * SEC (crypto unit) major compatible version determination
  */
-#if defined(CONFIG_FSL_CORENET)
+#if defined(CONFIG_FSL_CORENET) || \
+    defined(CONFIG_P1010)
 #define CONFIG_SYS_FSL_SEC_COMPAT	4
 #elif defined(CONFIG_MPC85xx) || defined(CONFIG_MPC83xx)
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 71fafa3..6b43dc5 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -1038,6 +1038,8 @@
 #define SVR_8569_E	0x808800
 #define SVR_8572	0x80E000
 #define SVR_8572_E	0x80E800
+#define SVR_P1010	0x80F100
+#define SVR_P1010_E	0x80F900
 #define SVR_P1011	0x80E500
 #define SVR_P1011_E	0x80ED00
 #define SVR_P1012	0x80E501
diff --git a/drivers/misc/fsl_law.c b/drivers/misc/fsl_law.c
index 6589076..931cc71 100644
--- a/drivers/misc/fsl_law.c
+++ b/drivers/misc/fsl_law.c
@@ -38,6 +38,7 @@ DECLARE_GLOBAL_DATA_PTR;
       defined(CONFIG_MPC8641) || defined(CONFIG_MPC8610)
 #define FSL_HW_NUM_LAWS 10
 #elif defined(CONFIG_MPC8536) || defined(CONFIG_MPC8572) || \
+      defined(CONFIG_P1010) || \
       defined(CONFIG_P1011) || defined(CONFIG_P1020) || \
       defined(CONFIG_P1012) || defined(CONFIG_P1021) || \
       defined(CONFIG_P1013) || defined(CONFIG_P1022) || \
-- 
1.7.2.3

^ permalink raw reply related	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor
  2011-01-14 16:41 [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
@ 2011-01-14 16:41 ` Kumar Gala
  2011-01-18  4:17   ` Kumar Gala
  2011-01-19  8:10   ` Wolfgang Denk
  2011-01-18  4:17 ` [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
  2011-01-19  8:09 ` Wolfgang Denk
  2 siblings, 2 replies; 7+ messages in thread
From: Kumar Gala @ 2011-01-14 16:41 UTC (permalink / raw)
  To: u-boot

From: Poonam Aggrwal <poonam.aggrwal@freescale.com>

The P1014 is similar to the P1010 processor with the following differences:

- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/cpu/mpc85xx/Makefile    |    1 +
 arch/powerpc/cpu/mpc8xxx/cpu.c       |    2 ++
 arch/powerpc/include/asm/config.h    |    4 ++--
 arch/powerpc/include/asm/processor.h |    2 ++
 drivers/misc/fsl_law.c               |    2 +-
 5 files changed, 8 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile
index e1261cf..3f118db 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -54,6 +54,7 @@ COBJS-$(CONFIG_P1010)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1011)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1012)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1013)	+= ddr-gen3.o
+COBJS-$(CONFIG_P1014)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1020)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1021)	+= ddr-gen3.o
 COBJS-$(CONFIG_P1022)	+= ddr-gen3.o
diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
index ac720a5..0ec1c16 100644
--- a/arch/powerpc/cpu/mpc8xxx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
@@ -71,6 +71,8 @@ struct cpu_type cpu_type_list [] = {
 	CPU_TYPE_ENTRY(P1012, P1012, 1),
 	CPU_TYPE_ENTRY(P1012, P1012_E, 1),
 	CPU_TYPE_ENTRY(P1013, P1013, 1),
+	CPU_TYPE_ENTRY(P1014, P1014_E, 1),
+	CPU_TYPE_ENTRY(P1014, P1014, 1),
 	CPU_TYPE_ENTRY(P1013, P1013_E, 1),
 	CPU_TYPE_ENTRY(P1020, P1020, 2),
 	CPU_TYPE_ENTRY(P1020, P1020_E, 2),
diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h
index d80fc97..965c874 100644
--- a/arch/powerpc/include/asm/config.h
+++ b/arch/powerpc/include/asm/config.h
@@ -69,7 +69,7 @@
 
 /* Enable TSEC2.0 for the platforms that have it if we are using TSEC */
 #if defined(CONFIG_TSEC_ENET) && \
-    (defined(CONFIG_P1010) || \
+    (defined(CONFIG_P1010) || defined(CONFIG_P1014) || \
      defined(CONFIG_P1020) || defined(CONFIG_P1011))
 #define CONFIG_TSECV2
 #endif
@@ -78,7 +78,7 @@
  * SEC (crypto unit) major compatible version determination
  */
 #if defined(CONFIG_FSL_CORENET) || \
-    defined(CONFIG_P1010)
+    defined(CONFIG_P1010) || defined(CONFIG_P1014)
 #define CONFIG_SYS_FSL_SEC_COMPAT	4
 #elif defined(CONFIG_MPC85xx) || defined(CONFIG_MPC83xx)
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 6b43dc5..646e0db 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -1046,6 +1046,8 @@
 #define SVR_P1012_E	0x80ED01
 #define SVR_P1013	0x80E700
 #define SVR_P1013_E	0x80EF00
+#define SVR_P1014	0x80F101
+#define SVR_P1014_E	0x80F901
 #define SVR_P1020	0x80E400
 #define SVR_P1020_E	0x80EC00
 #define SVR_P1021	0x80E401
diff --git a/drivers/misc/fsl_law.c b/drivers/misc/fsl_law.c
index 931cc71..d2b0cde 100644
--- a/drivers/misc/fsl_law.c
+++ b/drivers/misc/fsl_law.c
@@ -38,7 +38,7 @@ DECLARE_GLOBAL_DATA_PTR;
       defined(CONFIG_MPC8641) || defined(CONFIG_MPC8610)
 #define FSL_HW_NUM_LAWS 10
 #elif defined(CONFIG_MPC8536) || defined(CONFIG_MPC8572) || \
-      defined(CONFIG_P1010) || \
+      defined(CONFIG_P1010) || defined(CONFIG_P1014) || \
       defined(CONFIG_P1011) || defined(CONFIG_P1020) || \
       defined(CONFIG_P1012) || defined(CONFIG_P1021) || \
       defined(CONFIG_P1013) || defined(CONFIG_P1022) || \
-- 
1.7.2.3

^ permalink raw reply related	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor
  2011-01-14 16:41 [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
  2011-01-14 16:41 ` [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor Kumar Gala
@ 2011-01-18  4:17 ` Kumar Gala
  2011-01-19  8:09 ` Wolfgang Denk
  2 siblings, 0 replies; 7+ messages in thread
From: Kumar Gala @ 2011-01-18  4:17 UTC (permalink / raw)
  To: u-boot


On Jan 14, 2011, at 10:41 AM, Kumar Gala wrote:

> From: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> 
> Key Features include of the P1010:
> * e500v2 core frequency operation of 500 to 800 MHz
> * Power consumption less than 5.0 W at 800 MHz core speed
> * Dual SATA 3 Gbps controllers with integrated PHY
> * Dual PCI Express controllers
> * Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
> 	* TCP/IP acceleration and classification capabilities
> 	* IEEE 1588 support
> 	* Lossless flow control
> 	* RGMII, SGMII
> * DDR3 with support for a 32-bit data interface (40 bits including ECC),
>  up to 800 MHz data rate 32/16-bit DDR3 memory controller
> * Dedicated security engine featuring trusted boot
> * TDM interface
> * Dual controller area networks (FlexCAN) controller
> * SD/MMC card controller supporting booting from Flash cards
> * USB 2.0 host and device controller with an on-chip, high-speed PHY
> * Integrated Flash controller (IFC)
> * Power Management Controller (PMC)
> * Four-channel, general-purpose DMA controller
> * I2C controller
> * Serial peripheral interface (SPI) controller with master and slave support
> * System timers including a periodic interrupt timer, real-time clock,
>  software watchdog timer, and four general-purpose timers
> * Dual DUARTs
> 
> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/cpu/mpc85xx/Makefile    |    1 +
> arch/powerpc/cpu/mpc8xxx/cpu.c       |    2 ++
> arch/powerpc/include/asm/config.h    |    6 ++++--
> arch/powerpc/include/asm/processor.h |    2 ++
> drivers/misc/fsl_law.c               |    1 +
> 5 files changed, 10 insertions(+), 2 deletions(-)

applied to 85xx

- k

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor
  2011-01-14 16:41 ` [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor Kumar Gala
@ 2011-01-18  4:17   ` Kumar Gala
  2011-01-19  8:10   ` Wolfgang Denk
  1 sibling, 0 replies; 7+ messages in thread
From: Kumar Gala @ 2011-01-18  4:17 UTC (permalink / raw)
  To: u-boot


On Jan 14, 2011, at 10:41 AM, Kumar Gala wrote:

> From: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> 
> The P1014 is similar to the P1010 processor with the following differences:
> 
> - 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
> - no eCAN interface. (P1010 has 2 eCAN interfaces)
> - Two SGMII interface (P1010 has 3 SGMII)
> - No secure boot
> 
> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/cpu/mpc85xx/Makefile    |    1 +
> arch/powerpc/cpu/mpc8xxx/cpu.c       |    2 ++
> arch/powerpc/include/asm/config.h    |    4 ++--
> arch/powerpc/include/asm/processor.h |    2 ++
> drivers/misc/fsl_law.c               |    2 +-
> 5 files changed, 8 insertions(+), 3 deletions(-)

applied to 85xx

- k

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor
  2011-01-14 16:41 [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
  2011-01-14 16:41 ` [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor Kumar Gala
  2011-01-18  4:17 ` [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
@ 2011-01-19  8:09 ` Wolfgang Denk
  2 siblings, 0 replies; 7+ messages in thread
From: Wolfgang Denk @ 2011-01-19  8:09 UTC (permalink / raw)
  To: u-boot

Dear Kumar Gala,

In message <1295023271-11897-1-git-send-email-galak@kernel.crashing.org> you wrote:
> From: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> 
> Key Features include of the P1010:
> * e500v2 core frequency operation of 500 to 800 MHz
> * Power consumption less than 5.0 W at 800 MHz core speed
> * Dual SATA 3 Gbps controllers with integrated PHY
> * Dual PCI Express controllers
> * Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
> 	* TCP/IP acceleration and classification capabilities
> 	* IEEE 1588 support
> 	* Lossless flow control
> 	* RGMII, SGMII
> * DDR3 with support for a 32-bit data interface (40 bits including ECC),
>   up to 800 MHz data rate 32/16-bit DDR3 memory controller
> * Dedicated security engine featuring trusted boot
> * TDM interface
> * Dual controller area networks (FlexCAN) controller
> * SD/MMC card controller supporting booting from Flash cards
> * USB 2.0 host and device controller with an on-chip, high-speed PHY
> * Integrated Flash controller (IFC)
> * Power Management Controller (PMC)
> * Four-channel, general-purpose DMA controller
> * I2C controller
> * Serial peripheral interface (SPI) controller with master and slave support
> * System timers including a periodic interrupt timer, real-time clock,
>   software watchdog timer, and four general-purpose timers
> * Dual DUARTs
> 
> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
...
> --- a/arch/powerpc/include/asm/config.h
> +++ b/arch/powerpc/include/asm/config.h
> @@ -69,14 +69,16 @@
>  
>  /* Enable TSEC2.0 for the platforms that have it if we are using TSEC */
>  #if defined(CONFIG_TSEC_ENET) && \
> -    (defined(CONFIG_P1020) || defined(CONFIG_P1011))
> +    (defined(CONFIG_P1010) || \
> +     defined(CONFIG_P1020) || defined(CONFIG_P1011))

Please keep list sorted.


Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Nobody goes to that restaurant anymore. It's too crowded.

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor
  2011-01-14 16:41 ` [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor Kumar Gala
  2011-01-18  4:17   ` Kumar Gala
@ 2011-01-19  8:10   ` Wolfgang Denk
  2011-01-19  9:10     ` Kumar Gala
  1 sibling, 1 reply; 7+ messages in thread
From: Wolfgang Denk @ 2011-01-19  8:10 UTC (permalink / raw)
  To: u-boot

Dear Kumar Gala,

In message <1295023271-11897-2-git-send-email-galak@kernel.crashing.org> you wrote:
> From: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> 
> The P1014 is similar to the P1010 processor with the following differences:
> 
> - 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
> - no eCAN interface. (P1010 has 2 eCAN interfaces)
> - Two SGMII interface (P1010 has 3 SGMII)
> - No secure boot
...
> --- a/arch/powerpc/include/asm/config.h
> +++ b/arch/powerpc/include/asm/config.h
> @@ -69,7 +69,7 @@
>  
>  /* Enable TSEC2.0 for the platforms that have it if we are using TSEC */
>  #if defined(CONFIG_TSEC_ENET) && \
> -    (defined(CONFIG_P1010) || \
> +    (defined(CONFIG_P1010) || defined(CONFIG_P1014) || \
>       defined(CONFIG_P1020) || defined(CONFIG_P1011))

Please sort list.

> diff --git a/drivers/misc/fsl_law.c b/drivers/misc/fsl_law.c
> index 931cc71..d2b0cde 100644
> --- a/drivers/misc/fsl_law.c
> +++ b/drivers/misc/fsl_law.c
> @@ -38,7 +38,7 @@ DECLARE_GLOBAL_DATA_PTR;
>        defined(CONFIG_MPC8641) || defined(CONFIG_MPC8610)
>  #define FSL_HW_NUM_LAWS 10
>  #elif defined(CONFIG_MPC8536) || defined(CONFIG_MPC8572) || \
> -      defined(CONFIG_P1010) || \
> +      defined(CONFIG_P1010) || defined(CONFIG_P1014) || \
>        defined(CONFIG_P1011) || defined(CONFIG_P1020) || \
>        defined(CONFIG_P1012) || defined(CONFIG_P1021) || \
>        defined(CONFIG_P1013) || defined(CONFIG_P1022) || \

Ditto.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Horses just naturally have mohawk haircuts.

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor
  2011-01-19  8:10   ` Wolfgang Denk
@ 2011-01-19  9:10     ` Kumar Gala
  0 siblings, 0 replies; 7+ messages in thread
From: Kumar Gala @ 2011-01-19  9:10 UTC (permalink / raw)
  To: u-boot

> Please sort list.
> 
>> diff --git a/drivers/misc/fsl_law.c b/drivers/misc/fsl_law.c
>> index 931cc71..d2b0cde 100644
>> --- a/drivers/misc/fsl_law.c
>> +++ b/drivers/misc/fsl_law.c
>> @@ -38,7 +38,7 @@ DECLARE_GLOBAL_DATA_PTR;
>>       defined(CONFIG_MPC8641) || defined(CONFIG_MPC8610)
>> #define FSL_HW_NUM_LAWS 10
>> #elif defined(CONFIG_MPC8536) || defined(CONFIG_MPC8572) || \
>> -      defined(CONFIG_P1010) || \
>> +      defined(CONFIG_P1010) || defined(CONFIG_P1014) || \
>>       defined(CONFIG_P1011) || defined(CONFIG_P1020) || \
>>       defined(CONFIG_P1012) || defined(CONFIG_P1021) || \
>>       defined(CONFIG_P1013) || defined(CONFIG_P1022) || \
> 
> Ditto.

The sorting of this list has always been non-alphabetical as we kept single & dual core defines together.

I'd rather leave this as is and clean up all of them in one swoop.  I'll post the cleanup patch shortly.

- k

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2011-01-19  9:10 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-01-14 16:41 [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
2011-01-14 16:41 ` [U-Boot] [PATCH 2/2] powerpc/85xx: Add Support for Freescale P1014 Processor Kumar Gala
2011-01-18  4:17   ` Kumar Gala
2011-01-19  8:10   ` Wolfgang Denk
2011-01-19  9:10     ` Kumar Gala
2011-01-18  4:17 ` [U-Boot] [PATCH 1/2] powerpc/85xx: Add Support for Freescale P1010 Processor Kumar Gala
2011-01-19  8:09 ` Wolfgang Denk

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.