* [PATCH 2/2] ARM: imx53_loco: add all board pad configure.
2011-01-27 9:19 [PATCH 1/2] ARM: imx53_loco: remove inavailable uart device and remove rts/cts support Richard Zhao
@ 2011-01-27 9:19 ` Richard Zhao
2011-01-27 9:23 ` [PATCH 1/2] ARM: imx53_loco: remove inavailable uart device and remove rts/cts support Sascha Hauer
1 sibling, 0 replies; 4+ messages in thread
From: Richard Zhao @ 2011-01-27 9:19 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
---
arch/arm/mach-mx5/board-mx53_loco.c | 141 ++++++++++++++++++++++++++++++++++-
1 files changed, 139 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-mx5/board-mx53_loco.c b/arch/arm/mach-mx5/board-mx53_loco.c
index d0ca65b..902e4aa 100644
--- a/arch/arm/mach-mx5/board-mx53_loco.c
+++ b/arch/arm/mach-mx5/board-mx53_loco.c
@@ -39,8 +39,145 @@
#define LOCO_FEC_PHY_RST IMX_GPIO_NR(7, 6)
static iomux_v3_cfg_t mx53_loco_pads[] = {
- MX53_PAD_CSI0_D10__UART1_TXD,
- MX53_PAD_CSI0_D11__UART1_RXD,
+ /* FEC */
+ MX53_PAD_FEC_MDC__FEC_MDC,
+ MX53_PAD_FEC_MDIO__FEC_MDIO,
+ MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
+ MX53_PAD_FEC_RX_ER__FEC_RX_ER,
+ MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
+ MX53_PAD_FEC_RXD1__FEC_RDATA_1,
+ MX53_PAD_FEC_RXD0__FEC_RDATA_0,
+ MX53_PAD_FEC_TX_EN__FEC_TX_EN,
+ MX53_PAD_FEC_TXD1__FEC_TDATA_1,
+ MX53_PAD_FEC_TXD0__FEC_TDATA_0,
+ /* FEC_nRST */
+ MX53_PAD_PATA_DA_0__GPIO7_6,
+ /* FEC_nINT */
+ MX53_PAD_PATA_DATA4__GPIO2_4,
+ /* AUDMUX5 */
+ MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC,
+ MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD,
+ MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS,
+ MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD,
+ /* I2C2 */
+ MX53_PAD_KEY_COL3__I2C2_SCL,
+ MX53_PAD_KEY_ROW3__I2C2_SDA,
+ /* SD1 */
+ MX53_PAD_SD1_CMD__ESDHC1_CMD,
+ MX53_PAD_SD1_CLK__ESDHC1_CLK,
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0,
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1,
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2,
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3,
+ /* SD3 */
+ MX53_PAD_PATA_DATA8__ESDHC3_DAT0,
+ MX53_PAD_PATA_DATA9__ESDHC3_DAT1,
+ MX53_PAD_PATA_DATA10__ESDHC3_DAT2,
+ MX53_PAD_PATA_DATA11__ESDHC3_DAT3,
+ MX53_PAD_PATA_DATA0__ESDHC3_DAT4,
+ MX53_PAD_PATA_DATA1__ESDHC3_DAT5,
+ MX53_PAD_PATA_DATA2__ESDHC3_DAT6,
+ MX53_PAD_PATA_DATA3__ESDHC3_DAT7,
+ MX53_PAD_PATA_IORDY__ESDHC3_CLK,
+ MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
+ /* SD3_CD */
+ MX53_PAD_EIM_DA11__GPIO3_11,
+ /* SD3_WP */
+ MX53_PAD_EIM_DA12__GPIO3_12,
+ /* VGA */
+ MX53_PAD_EIM_OE__IPU_DI1_PIN7,
+ MX53_PAD_EIM_RW__IPU_DI1_PIN8,
+ /* DISPLB */
+ MX53_PAD_EIM_D20__IPU_SER_DISP0_CS,
+ MX53_PAD_EIM_D21__IPU_DISPB0_SER_CLK,
+ MX53_PAD_EIM_D22__IPU_DISPB0_SER_DIN,
+ MX53_PAD_EIM_D23__IPU_DI0_D0_CS,
+ /* DISP0_POWER_EN */
+ MX53_PAD_EIM_D24__GPIO3_24,
+ /* DISP0 DET INT */
+ MX53_PAD_EIM_D31__GPIO3_31,
+ /* LVDS */
+ MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3,
+ MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK,
+ MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2,
+ MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1,
+ MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0,
+ MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3,
+ MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2,
+ MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK,
+ MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1,
+ MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0,
+ /* I2C1 */
+ MX53_PAD_CSI0_DAT8__I2C1_SDA,
+ MX53_PAD_CSI0_DAT9__I2C1_SCL,
+ /* UART1 */
+ MX53_PAD_CSI0_DAT10__UART1_TXD_MUX,
+ MX53_PAD_CSI0_DAT11__UART1_RXD_MUX,
+ /* CSI0 */
+ MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12,
+ MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13,
+ MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14,
+ MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15,
+ MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16,
+ MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17,
+ MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18,
+ MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19,
+ MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC,
+ MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC,
+ MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK,
+ /* DISPLAY */
+ MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
+ MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
+ MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
+ MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
+ MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
+ MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
+ MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
+ MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
+ MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
+ MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
+ MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
+ MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
+ MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
+ MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
+ MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
+ MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
+ MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
+ MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
+ MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
+ MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
+ MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
+ MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
+ MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
+ MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
+ MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
+ MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
+ MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
+ MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
+ /* Audio CLK*/
+ MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK,
+ /* PWM */
+ MX53_PAD_GPIO_1__PWM2_PWMO,
+ /* SPDIF */
+ MX53_PAD_GPIO_7__SPDIF_PLOCK,
+ MX53_PAD_GPIO_17__SPDIF_OUT1,
+ /* GPIO */
+ MX53_PAD_PATA_DA_1__GPIO7_7,
+ MX53_PAD_PATA_DA_2__GPIO7_8,
+ MX53_PAD_PATA_DATA5__GPIO2_5,
+ MX53_PAD_PATA_DATA6__GPIO2_6,
+ MX53_PAD_PATA_DATA14__GPIO2_14,
+ MX53_PAD_PATA_DATA15__GPIO2_15,
+ MX53_PAD_PATA_INTRQ__GPIO7_2,
+ MX53_PAD_EIM_WAIT__GPIO5_0,
+ MX53_PAD_NANDF_WP_B__GPIO6_9,
+ MX53_PAD_NANDF_RB0__GPIO6_10,
+ MX53_PAD_NANDF_CS1__GPIO6_14,
+ MX53_PAD_NANDF_CS2__GPIO6_15,
+ MX53_PAD_NANDF_CS3__GPIO6_16,
+ MX53_PAD_GPIO_5__GPIO1_5,
+ MX53_PAD_GPIO_16__GPIO7_11,
+ MX53_PAD_GPIO_8__GPIO1_8,
};
static inline void mx53_loco_init_uart(void)
--
1.6.3.3
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 1/2] ARM: imx53_loco: remove inavailable uart device and remove rts/cts support
2011-01-27 9:19 [PATCH 1/2] ARM: imx53_loco: remove inavailable uart device and remove rts/cts support Richard Zhao
2011-01-27 9:19 ` [PATCH 2/2] ARM: imx53_loco: add all board pad configure Richard Zhao
@ 2011-01-27 9:23 ` Sascha Hauer
2011-01-27 23:34 ` Richard Zhao
1 sibling, 1 reply; 4+ messages in thread
From: Sascha Hauer @ 2011-01-27 9:23 UTC (permalink / raw)
To: linux-arm-kernel
Richard,
Fabio posted a very similar patch. Please coordinate what should be done
here.
Sascha
On Thu, Jan 27, 2011 at 05:19:03PM +0800, Richard Zhao wrote:
> imx53_loco board only have one uart and the uart don't export rts/cts lines.
>
> Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
> ---
> arch/arm/mach-mx5/board-mx53_loco.c | 20 +-------------------
> 1 files changed, 1 insertions(+), 19 deletions(-)
>
> diff --git a/arch/arm/mach-mx5/board-mx53_loco.c b/arch/arm/mach-mx5/board-mx53_loco.c
> index d1348e0..d0ca65b 100644
> --- a/arch/arm/mach-mx5/board-mx53_loco.c
> +++ b/arch/arm/mach-mx5/board-mx53_loco.c
> @@ -41,29 +41,11 @@
> static iomux_v3_cfg_t mx53_loco_pads[] = {
> MX53_PAD_CSI0_D10__UART1_TXD,
> MX53_PAD_CSI0_D11__UART1_RXD,
> - MX53_PAD_ATA_DIOW__UART1_TXD,
> - MX53_PAD_ATA_DMACK__UART1_RXD,
> -
> - MX53_PAD_ATA_BUFFER_EN__UART2_RXD,
> - MX53_PAD_ATA_DMARQ__UART2_TXD,
> - MX53_PAD_ATA_DIOR__UART2_RTS,
> - MX53_PAD_ATA_INTRQ__UART2_CTS,
> -
> - MX53_PAD_ATA_CS_0__UART3_TXD,
> - MX53_PAD_ATA_CS_1__UART3_RXD,
> - MX53_PAD_ATA_DA_1__UART3_CTS,
> - MX53_PAD_ATA_DA_2__UART3_RTS,
> -};
> -
> -static const struct imxuart_platform_data mx53_loco_uart_data __initconst = {
> - .flags = IMXUART_HAVE_RTSCTS,
> };
>
> static inline void mx53_loco_init_uart(void)
> {
> - imx53_add_imx_uart(0, &mx53_loco_uart_data);
> - imx53_add_imx_uart(1, &mx53_loco_uart_data);
> - imx53_add_imx_uart(2, &mx53_loco_uart_data);
> + imx53_add_imx_uart(0, NULL);
> }
>
> static inline void mx53_loco_fec_reset(void)
> --
> 1.6.3.3
>
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
^ permalink raw reply [flat|nested] 4+ messages in thread