* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-01-27 22:46 ` [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again Remy Bohmer
@ 2011-01-27 22:49 ` Remy Bohmer
2011-01-27 23:11 ` Albert ARIBAUD
2011-02-01 10:45 ` Michael Trimarchi
2 siblings, 0 replies; 12+ messages in thread
From: Remy Bohmer @ 2011-01-27 22:49 UTC (permalink / raw)
To: u-boot
Hi All,
2011/1/27 Remy Bohmer <linux@bohmer.net>:
> Since U-boot v2010.12 the at91sam9261ek board is broken.
> This is solved and tested on this board.
>
> Note: It requires that the 1st stage bootloader (like Atmel at91-bootstrap)
> to load U-boot at a different address compared to previous releases of
> U-boot due to conflicts in the BSS area during relocation.
> (0x23f00000 -> -0x23e00000)
>
> Derived from a patch of: Alexander Stein <alexander.stein@systec-electronic.com>
>
> Signed-off-by: Remy Bohmer <linux@bohmer.net>
For your information: This patch requires this patch applied to the
tree first to make it work:
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/93537
Kind regards,
Remy
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-01-27 22:46 ` [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again Remy Bohmer
2011-01-27 22:49 ` Remy Bohmer
@ 2011-01-27 23:11 ` Albert ARIBAUD
2011-01-28 20:38 ` Remy Bohmer
2011-02-01 10:45 ` Michael Trimarchi
2 siblings, 1 reply; 12+ messages in thread
From: Albert ARIBAUD @ 2011-01-27 23:11 UTC (permalink / raw)
To: u-boot
Hi Remy,
Le 27/01/2011 23:46, Remy Bohmer a ?crit :
> Since U-boot v2010.12 the at91sam9261ek board is broken.
> This is solved and tested on this board.
>
> Note: It requires that the 1st stage bootloader (like Atmel at91-bootstrap)
> to load U-boot at a different address compared to previous releases of
> U-boot due to conflicts in the BSS area during relocation.
> (0x23f00000 -> -0x23e00000)
>
> Derived from a patch of: Alexander Stein<alexander.stein@systec-electronic.com>
>
> Signed-off-by: Remy Bohmer<linux@bohmer.net>
> ---
> board/atmel/at91sam9261ek/Makefile | 10 +++++-----
> board/atmel/at91sam9261ek/at91sam9261ek.c | 7 ++++---
> board/atmel/at91sam9261ek/config.mk | 1 -
> include/configs/at91sam9261ek.h | 25 +++++++++++++++++++++----
> 4 files changed, 30 insertions(+), 13 deletions(-)
> delete mode 100644 board/atmel/at91sam9261ek/config.mk
>
> diff --git a/board/atmel/at91sam9261ek/Makefile b/board/atmel/at91sam9261ek/Makefile
> index 9d20ba0..1da810f 100644
> --- a/board/atmel/at91sam9261ek/Makefile
> +++ b/board/atmel/at91sam9261ek/Makefile
> @@ -29,16 +29,16 @@ include $(TOPDIR)/config.mk
>
> LIB = $(obj)lib$(BOARD).o
>
> -COBJS-y += at91sam9261ek.o
> +COBJS-y += $(BOARD).o
> COBJS-y += led.o
> COBJS-$(CONFIG_HAS_DATAFLASH) += partition.o
>
> -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
> -OBJS := $(addprefix $(obj),$(COBJS-y))
> -SOBJS := $(addprefix $(obj),$(SOBJS))
> +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS-y) $(SOBJS-y))
> +SOBJS := $(addprefix $(obj),$(SOBJS-y))
What is the rationale for putting both C *and* assembly language objects
in OBJS?
> $(LIB): $(obj).depend $(OBJS) $(SOBJS)
> - $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> + $(call cmd_link_o_target, $(OBJS))
If there is a rationale for putting all objects in OBJS, then SOBJS
should be removed from the dependencies of LIB. If there is not, then
SOBJS should remain in the '$(call...)'.
> clean:
> rm -f $(SOBJS) $(OBJS)
> diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c
> index de5cfae..25c181e 100644
> --- a/board/atmel/at91sam9261ek/at91sam9261ek.c
> +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c
> @@ -246,7 +246,7 @@ int board_init(void)
> gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
> #endif
> /* adress of boot parameters */
> - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
>
> at91_serial_hw_init();
> #ifdef CONFIG_CMD_NAND
> @@ -273,8 +273,9 @@ int board_eth_init(bd_t *bis)
>
> int dram_init(void)
> {
> - gd->bd->bi_dram[0].start = PHYS_SDRAM;
> - gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
> + /* dram_init must store complete ramsize in gd->ram_size */
> + gd->ram_size = get_ram_size((volatile long *)CONFIG_SYS_SDRAM_BASE,
> + CONFIG_SYS_SDRAM_SIZE);
> return 0;
> }
>
> diff --git a/board/atmel/at91sam9261ek/config.mk b/board/atmel/at91sam9261ek/config.mk
> deleted file mode 100644
> index e554a45..0000000
> --- a/board/atmel/at91sam9261ek/config.mk
> +++ /dev/null
> @@ -1 +0,0 @@
> -CONFIG_SYS_TEXT_BASE = 0x23f00000
> diff --git a/include/configs/at91sam9261ek.h b/include/configs/at91sam9261ek.h
> index 401478b..0cffd94 100644
> --- a/include/configs/at91sam9261ek.h
> +++ b/include/configs/at91sam9261ek.h
> @@ -27,6 +27,8 @@
> #ifndef __CONFIG_H
> #define __CONFIG_H
>
> +#include<asm/sizes.h>
> +
> #define CONFIG_AT91_LEGACY
>
> /* ARM asynchronous clock */
> @@ -39,6 +41,7 @@
> #else
> #define CONFIG_AT91SAM9261 1 /* It's an Atmel AT91SAM9261 SoC*/
> #endif
> +#define CONFIG_AT91FAMILY
> #define CONFIG_ARCH_CPU_INIT
> #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
>
> @@ -105,11 +108,21 @@
> #define CONFIG_CMD_DHCP 1
> #define CONFIG_CMD_NAND 1
> #define CONFIG_CMD_USB 1
> +#define CONFIG_CMD_CACHE 1
>
> /* SDRAM */
> #define CONFIG_NR_DRAM_BANKS 1
> -#define PHYS_SDRAM 0x20000000
> -#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
> +#define CONFIG_SYS_SDRAM_BASE 0x20000000
> +#define CONFIG_SYS_SDRAM_SIZE SZ_64M /* 64 megs */
> +
> +/*
> + * AT91-bootstrap expects that U-boot needs to be loaded at 0x23f00000
> + * but since U-boot is now being relocated to the end of RAM which is
> + * almost in the same area, there will be an overlap in the BSS segment
> + * resulting in a lockup during boot. So, we need to tell the
> + * AT91-bootstrap code to load it at a lower address, namely 0x23e00000
> + */
> +#define CONFIG_SYS_TEXT_BASE 0x23e00000
>
> /* DataFlash */
> #define CONFIG_ATMEL_DATAFLASH_SPI
> @@ -168,7 +181,7 @@
>
> #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
>
> -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
> +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
> #define CONFIG_SYS_MEMTEST_END 0x23e00000
>
> #ifdef CONFIG_SYS_USE_DATAFLASH_CS0
> @@ -230,8 +243,12 @@
> * Size of malloc() pool
> */
> #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
> +/* size in bytes reserved for initial data */
> +
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \
> + - GENERATED_GBL_DATA_SIZE)
>
> -#define CONFIG_STACKSIZE (32*1024) /* regular stack */
> +#define CONFIG_STACKSIZE (SZ_32K) /* regular stack */
Do not use SZ_ constants -- several instances in this patch.
> #ifdef CONFIG_USE_IRQ
> #error CONFIG_USE_IRQ not supported
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-01-27 23:11 ` Albert ARIBAUD
@ 2011-01-28 20:38 ` Remy Bohmer
0 siblings, 0 replies; 12+ messages in thread
From: Remy Bohmer @ 2011-01-28 20:38 UTC (permalink / raw)
To: u-boot
Hi,
>> -COBJS-y += at91sam9261ek.o
>> +COBJS-y += $(BOARD).o
>> ? COBJS-y += led.o
>> ? COBJS-$(CONFIG_HAS_DATAFLASH) += partition.o
>>
>> -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
>> -OBJS := $(addprefix $(obj),$(COBJS-y))
>> -SOBJS ? ? ? ?:= $(addprefix $(obj),$(SOBJS))
>> +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
>> +OBJS := $(addprefix $(obj),$(COBJS-y) $(SOBJS-y))
>> +SOBJS ? ? ? ?:= $(addprefix $(obj),$(SOBJS-y))
>
> What is the rationale for putting both C *and* assembly language objects
> in OBJS?
No rationale, except made this Makefile more in line with another board.
Reworked, will be in patch-v2
>>
>> -#define CONFIG_STACKSIZE ? ? (32*1024) ? ? ? /* regular stack */
>> +#define CONFIG_STACKSIZE ? ? (SZ_32K) ? ? ? ?/* regular stack */
>
> Do not use SZ_ constants -- several instances in this patch.
Reverted these changes in patch-v2.
Thanks.
Kind regards,
Remy
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-01-27 22:46 ` [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again Remy Bohmer
2011-01-27 22:49 ` Remy Bohmer
2011-01-27 23:11 ` Albert ARIBAUD
@ 2011-02-01 10:45 ` Michael Trimarchi
2011-02-01 12:16 ` Albert ARIBAUD
2 siblings, 1 reply; 12+ messages in thread
From: Michael Trimarchi @ 2011-02-01 10:45 UTC (permalink / raw)
To: u-boot
Dear Remy
On 01/27/2011 11:46 PM, Remy Bohmer wrote:
> Since U-boot v2010.12 the at91sam9261ek board is broken.
> This is solved and tested on this board.
>
> Note: It requires that the 1st stage bootloader (like Atmel at91-bootstrap)
> to load U-boot at a different address compared to previous releases of
> U-boot due to conflicts in the BSS area during relocation.
> (0x23f00000 -> -0x23e00000)
>
> Derived from a patch of: Alexander Stein <alexander.stein@systec-electronic.com>
>
> Signed-off-by: Remy Bohmer <linux@bohmer.net>
Hi
/home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld -pie -r -o libat91.o lowlevel_init.o clock.o cpu.o reset.o timer.o
/home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: -r and -shared may not be used together
I have tried this patch but this a problem releated to linking option. Do you have this problem?
Michael
> ---
> board/atmel/at91sam9261ek/Makefile | 10 +++++-----
> board/atmel/at91sam9261ek/at91sam9261ek.c | 7 ++++---
> board/atmel/at91sam9261ek/config.mk | 1 -
> include/configs/at91sam9261ek.h | 25 +++++++++++++++++++++----
> 4 files changed, 30 insertions(+), 13 deletions(-)
> delete mode 100644 board/atmel/at91sam9261ek/config.mk
>
> diff --git a/board/atmel/at91sam9261ek/Makefile b/board/atmel/at91sam9261ek/Makefile
> index 9d20ba0..1da810f 100644
> --- a/board/atmel/at91sam9261ek/Makefile
> +++ b/board/atmel/at91sam9261ek/Makefile
> @@ -29,16 +29,16 @@ include $(TOPDIR)/config.mk
>
> LIB = $(obj)lib$(BOARD).o
>
> -COBJS-y += at91sam9261ek.o
> +COBJS-y += $(BOARD).o
> COBJS-y += led.o
> COBJS-$(CONFIG_HAS_DATAFLASH) += partition.o
>
> -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
> -OBJS := $(addprefix $(obj),$(COBJS-y))
> -SOBJS := $(addprefix $(obj),$(SOBJS))
> +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS-y) $(SOBJS-y))
> +SOBJS := $(addprefix $(obj),$(SOBJS-y))
>
> $(LIB): $(obj).depend $(OBJS) $(SOBJS)
> - $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> + $(call cmd_link_o_target, $(OBJS))
>
> clean:
> rm -f $(SOBJS) $(OBJS)
> diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c
> index de5cfae..25c181e 100644
> --- a/board/atmel/at91sam9261ek/at91sam9261ek.c
> +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c
> @@ -246,7 +246,7 @@ int board_init(void)
> gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
> #endif
> /* adress of boot parameters */
> - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
>
> at91_serial_hw_init();
> #ifdef CONFIG_CMD_NAND
> @@ -273,8 +273,9 @@ int board_eth_init(bd_t *bis)
>
> int dram_init(void)
> {
> - gd->bd->bi_dram[0].start = PHYS_SDRAM;
> - gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
> + /* dram_init must store complete ramsize in gd->ram_size */
> + gd->ram_size = get_ram_size((volatile long *)CONFIG_SYS_SDRAM_BASE,
> + CONFIG_SYS_SDRAM_SIZE);
> return 0;
> }
>
> diff --git a/board/atmel/at91sam9261ek/config.mk b/board/atmel/at91sam9261ek/config.mk
> deleted file mode 100644
> index e554a45..0000000
> --- a/board/atmel/at91sam9261ek/config.mk
> +++ /dev/null
> @@ -1 +0,0 @@
> -CONFIG_SYS_TEXT_BASE = 0x23f00000
> diff --git a/include/configs/at91sam9261ek.h b/include/configs/at91sam9261ek.h
> index 401478b..0cffd94 100644
> --- a/include/configs/at91sam9261ek.h
> +++ b/include/configs/at91sam9261ek.h
> @@ -27,6 +27,8 @@
> #ifndef __CONFIG_H
> #define __CONFIG_H
>
> +#include <asm/sizes.h>
> +
> #define CONFIG_AT91_LEGACY
>
> /* ARM asynchronous clock */
> @@ -39,6 +41,7 @@
> #else
> #define CONFIG_AT91SAM9261 1 /* It's an Atmel AT91SAM9261 SoC*/
> #endif
> +#define CONFIG_AT91FAMILY
> #define CONFIG_ARCH_CPU_INIT
> #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
>
> @@ -105,11 +108,21 @@
> #define CONFIG_CMD_DHCP 1
> #define CONFIG_CMD_NAND 1
> #define CONFIG_CMD_USB 1
> +#define CONFIG_CMD_CACHE 1
>
> /* SDRAM */
> #define CONFIG_NR_DRAM_BANKS 1
> -#define PHYS_SDRAM 0x20000000
> -#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
> +#define CONFIG_SYS_SDRAM_BASE 0x20000000
> +#define CONFIG_SYS_SDRAM_SIZE SZ_64M /* 64 megs */
> +
> +/*
> + * AT91-bootstrap expects that U-boot needs to be loaded at 0x23f00000
> + * but since U-boot is now being relocated to the end of RAM which is
> + * almost in the same area, there will be an overlap in the BSS segment
> + * resulting in a lockup during boot. So, we need to tell the
> + * AT91-bootstrap code to load it at a lower address, namely 0x23e00000
> + */
> +#define CONFIG_SYS_TEXT_BASE 0x23e00000
>
> /* DataFlash */
> #define CONFIG_ATMEL_DATAFLASH_SPI
> @@ -168,7 +181,7 @@
>
> #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
>
> -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
> +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
> #define CONFIG_SYS_MEMTEST_END 0x23e00000
>
> #ifdef CONFIG_SYS_USE_DATAFLASH_CS0
> @@ -230,8 +243,12 @@
> * Size of malloc() pool
> */
> #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
> +/* size in bytes reserved for initial data */
> +
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \
> + - GENERATED_GBL_DATA_SIZE)
>
> -#define CONFIG_STACKSIZE (32*1024) /* regular stack */
> +#define CONFIG_STACKSIZE (SZ_32K) /* regular stack */
>
> #ifdef CONFIG_USE_IRQ
> #error CONFIG_USE_IRQ not supported
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-02-01 10:45 ` Michael Trimarchi
@ 2011-02-01 12:16 ` Albert ARIBAUD
2011-02-01 19:11 ` Michael Trimarchi
2011-02-01 19:54 ` Reinhard Meyer
0 siblings, 2 replies; 12+ messages in thread
From: Albert ARIBAUD @ 2011-02-01 12:16 UTC (permalink / raw)
To: u-boot
Le 01/02/2011 11:45, Michael Trimarchi a ?crit :
> Hi
>
> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld -pie -r -o libat91.o lowlevel_init.o clock.o cpu.o reset.o timer.o
> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: -r and -shared may not be used together
>
> I have tried this patch but this a problem releated to linking option. Do you have this problem?
>
> Michael
Read up recent posts on the list: this was detected and is fixed in the
master branch of the u-boot-arm repository.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-02-01 12:16 ` Albert ARIBAUD
@ 2011-02-01 19:11 ` Michael Trimarchi
2011-02-01 19:31 ` Remy Bohmer
2011-02-01 19:54 ` Reinhard Meyer
1 sibling, 1 reply; 12+ messages in thread
From: Michael Trimarchi @ 2011-02-01 19:11 UTC (permalink / raw)
To: u-boot
Hi
On 02/01/2011 01:16 PM, Albert ARIBAUD wrote:
> Le 01/02/2011 11:45, Michael Trimarchi a ?crit :
>
>> Hi
>>
>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld -pie -r -o libat91.o lowlevel_init.o clock.o cpu.o reset.o timer.o
>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: -r and -shared may not be used together
>>
>> I have tried this patch but this a problem releated to linking option. Do you have this problem?
>>
>> Michael
>
> Read up recent posts on the list: this was detected and is fixed in the
> master branch of the u-boot-arm repository.
>
> Amicalement,
I see, but I see but I have other little problem. I have fixed the compilation, but I have a segmentation fault.
Starting program: /opt/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld -pie -Bstatic -T u-boot.lds -Ttext 0x23e00000 arch/arm/cpu/arm926ejs/start.o --start-group api/libapi.o arch/arm/cpu/arm926ejs/at91/libat91.o arch/arm/cpu/arm926ejs/libarm926ejs.o arch/arm/lib/libarm.o common/libcommon.o disk/libdisk.o drivers/bios_emulator/libatibiosemu.o drivers/block/libblock.o drivers/dma/libdma.o drivers/fpga/libfpga.o drivers/gpio/libgpio.o drivers/hwmon/libhwmon.o drivers/i2c/libi2c.o drivers/input/libinput.o drivers/misc/libmisc.o drivers/mmc/libmmc.o drivers/mtd/libmtd.o drivers/mtd/nand/libnand.o drivers/mtd/onenand/libonenand.o drivers/mtd/spi/libspi_flash.o drivers/mtd/ubi/libubi.o drivers/net/libnet.o drivers/net/phy/libphy.o drivers/pci/libpci.o drivers/pcmcia/libpcmcia.o drivers/power/libpower.o drivers/rtc/librtc.o drivers/serial/libserial.o drivers/spi/libspi.o drivers/twserial/libtws.o drivers/usb/gadget/libusb_gadget.o
drivers/usb/host/libusb_host.o drivers/usb/musb/libusb_musb.o drivers/usb/phy/libusb_phy.o drivers/video/libvideo.o drivers/watchdog/libwatchdog.o fs/cramfs/libcramfs.o fs/ext2/libext2fs.o fs/fat/libfat.o fs/fdos/libfdos.o fs/jffs2/libjffs2.o fs/reiserfs/libreiserfs.o fs/ubifs/libubifs.o fs/yaffs2/libyaffs2.o lib/libfdt/libfdt.o lib/libgeneric.o lib/lzma/liblzma.o lib/lzo/liblzo.o net/libnet.o post/libpost.o board/atmel/at91sam9261ek/libat91sam9261ek.o --end-group /home/michael/u-boot/arch/arm/lib/eabi_compat.o -L /opt/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/../lib/gcc/arm-none-linux-gnueabi/4.1.2 -lgcc -Map u-boot.map -o u-boot
/opt/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: u-boot: warning: allocated section `.bss' not in segment
Program received signal SIGSEGV, Segmentation fault.
0x08081ebd in elf32_arm_finish_dynamic_sections ()
(gdb) bt
#0 0x08081ebd in elf32_arm_finish_dynamic_sections ()
#1 0x0809cc2b in bfd_elf_final_link ()
#2 0x0807b525 in elf32_arm_bfd_final_link ()
#3 0x0805bfce in ldwrite ()
#4 0x0805a0be in main ()
Michael
-------------- next part --------------
A non-text attachment was scrubbed...
Name: timer.patch
Type: text/x-patch
Size: 673 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20110201/f1326848/attachment.bin
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-02-01 19:11 ` Michael Trimarchi
@ 2011-02-01 19:31 ` Remy Bohmer
0 siblings, 0 replies; 12+ messages in thread
From: Remy Bohmer @ 2011-02-01 19:31 UTC (permalink / raw)
To: u-boot
Hi,
2011/2/1 Michael Trimarchi <trimarchi@gandalf.sssup.it>:
> Hi
>
> On 02/01/2011 01:16 PM, Albert ARIBAUD wrote:
>> Le 01/02/2011 11:45, Michael Trimarchi a ?crit :
>>
>>> Hi
>>>
>>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld ?-pie -r -o libat91.o ?lowlevel_init.o clock.o cpu.o reset.o timer.o
>>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: -r and -shared may not be used together
>>>
>>> I have tried this patch but this a problem releated to linking option. Do you have this problem?
>>>
>>> Michael
>>
>> Read up recent posts on the list: this was detected and is fixed in the
>> master branch of the u-boot-arm repository.
I mentioned this as well directly after posting this patch for the first time.
But anyway, if you look at 'cdc-at91' branch of u-boot-usb you can see
all the other patches that are required to make it compile properly.
Including the timer fix for the at91 family.
>>
>> Amicalement,
> I see, but I see but I have other little problem. I have fixed the compilation, but I have a segmentation fault.
>
> Starting program: /opt/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld -pie -Bstatic -T u-boot.lds -Ttext 0x23e00000 arch/arm/cpu/arm926ejs/start.o --start-group api/libapi.o arch/arm/cpu/arm926ejs/at91/libat91.o arch/arm/cpu/arm926ejs/libarm926ejs.o arch/arm/lib/libarm.o common/libcommon.o disk/libdisk.o drivers/bios_emulator/libatibiosemu.o drivers/block/libblock.o drivers/dma/libdma.o drivers/fpga/libfpga.o drivers/gpio/libgpio.o drivers/hwmon/libhwmon.o drivers/i2c/libi2c.o drivers/input/libinput.o drivers/misc/libmisc.o drivers/mmc/libmmc.o drivers/mtd/libmtd.o drivers/mtd/nand/libnand.o drivers/mtd/onenand/libonenand.o drivers/mtd/spi/libspi_flash.o drivers/mtd/ubi/libubi.o drivers/net/libnet.o drivers/net/phy/libphy.o drivers/pci/libpci.o drivers/pcmcia/libpcmcia.o drivers/power/libpower.o drivers/rtc/librtc.o drivers/serial/libserial.o drivers/spi/libspi.o drivers/twserial/libtws.o drivers/usb/gadget/libusb_gadget.o
> drivers/usb/host/libusb_host.o drivers/usb/musb/libusb_musb.o drivers/usb/phy/libusb_phy.o drivers/video/libvideo.o drivers/watchdog/libwatchdog.o fs/cramfs/libcramfs.o fs/ext2/libext2fs.o fs/fat/libfat.o fs/fdos/libfdos.o fs/jffs2/libjffs2.o fs/reiserfs/libreiserfs.o fs/ubifs/libubifs.o fs/yaffs2/libyaffs2.o lib/libfdt/libfdt.o lib/libgeneric.o lib/lzma/liblzma.o lib/lzo/liblzo.o net/libnet.o post/libpost.o board/atmel/at91sam9261ek/libat91sam9261ek.o --end-group /home/michael/u-boot/arch/arm/lib/eabi_compat.o -L /opt/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/../lib/gcc/arm-none-linux-gnueabi/4.1.2 -lgcc -Map u-boot.map -o u-boot
> /opt/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: u-boot: warning: allocated section `.bss' not in segment
>
> Program received signal SIGSEGV, Segmentation fault.
> 0x08081ebd in elf32_arm_finish_dynamic_sections ()
> (gdb) bt
> #0 ?0x08081ebd in elf32_arm_finish_dynamic_sections ()
> #1 ?0x0809cc2b in bfd_elf_final_link ()
> #2 ?0x0807b525 in elf32_arm_bfd_final_link ()
> #3 ?0x0805bfce in ldwrite ()
> #4 ?0x0805a0be in main ()
>
> Michael
I see you use a rather old compiler.
I tested with a GCC 4.3.4 (CodeSourcery 2009q1) compiler which works
okay. I also noticed that the current make structure of U-boot is more
picky on linker usage, and even unresolved externals result in
crashing linkers. This has nothing to do with this patch though.
Kind regards,
Remy
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-02-01 12:16 ` Albert ARIBAUD
2011-02-01 19:11 ` Michael Trimarchi
@ 2011-02-01 19:54 ` Reinhard Meyer
2011-02-05 12:54 ` Remy Bohmer
1 sibling, 1 reply; 12+ messages in thread
From: Reinhard Meyer @ 2011-02-01 19:54 UTC (permalink / raw)
To: u-boot
Dear all,
>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld -pie -r -o libat91.o lowlevel_init.o clock.o cpu.o reset.o timer.o
>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: -r and -shared may not be used together
>>
>> I have tried this patch but this a problem releated to linking option. Do you have this problem?
>>
>> Michael
>
> Read up recent posts on the list: this was detected and is fixed in the
> master branch of the u-boot-arm repository.
I'll rebase u-boot-atmel on u-boot-arm/master then. Please rebase at91 related patches on
u-boot-atmel/rework then (my time permitting, that branch will exist somewhere tomorrow)
Best Regards,
Reinhard
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/2] at91sam9261ek: make operational again
2011-02-01 19:54 ` Reinhard Meyer
@ 2011-02-05 12:54 ` Remy Bohmer
0 siblings, 0 replies; 12+ messages in thread
From: Remy Bohmer @ 2011-02-05 12:54 UTC (permalink / raw)
To: u-boot
Hi,
2011/2/1 Reinhard Meyer <u-boot@emk-elektronik.de>:
> Dear all,
>>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld ?-pie -r -o libat91.o ?lowlevel_init.o clock.o cpu.o reset.o timer.o
>>> /home/toolchain/bin/gcc-4.1.2-glibc-2.5-nptl-3/arm-none-linux-gnueabi/bin/arm-none-linux-gnueabi-ld: -r and -shared may not be used together
>>>
>>> I have tried this patch but this a problem releated to linking option. Do you have this problem?
>>>
>>> Michael
>>
>> Read up recent posts on the list: this was detected and is fixed in the
>> master branch of the u-boot-arm repository.
> I'll rebase u-boot-atmel on u-boot-arm/master then. Please rebase at91 related patches on
> u-boot-atmel/rework then (my time permitting, that branch will exist somewhere tomorrow)
I just posted a rework of these patch series, based on your latest rework branch
It removes a lot of legacy code and makes the boards compile and
operational again. It has been tested on real hardware.
To make it easier for you: You can pull the series here or from the ML. :-))
-------------------------
The following changes since commit 137f4defd8f8d8d2198b4981d25614a1cbcf4587:
AT91: enable MMC on at91sam(9260/9g20/0xe)ek (2011-02-02 10:11:07 +0100)
are available in the git repository at:
git://git.denx.de/u-boot-usb.git fix-at91sam9261ek
Remy Bohmer (2):
at91sam9261ek: make operational again
Make at91sam9261ek and at91sam9g10ek work on current u-boot-atmel.git
Makefile | 23 ---
arch/arm/cpu/arm926ejs/at91/at91sam9261_devices.c | 31 ++--
arch/arm/cpu/arm926ejs/at91/led.c | 1 -
arch/arm/include/asm/arch-at91/at91_matrix.h | 17 ++-
arch/arm/include/asm/arch-at91/at91sam9261.h | 1 +
.../arm/include/asm/arch-at91/at91sam9261_matrix.h | 64 ---------
board/atmel/at91sam9261ek/Makefile | 6 +-
board/atmel/at91sam9261ek/at91sam9261ek.c | 147 +++++++++++---------
board/atmel/at91sam9261ek/config.mk | 1 -
board/atmel/at91sam9261ek/led.c | 8 +-
boards.cfg | 6 +
doc/README.at91 | 3 +-
include/configs/at91sam9261ek.h | 142 +++++++++++--------
13 files changed, 201 insertions(+), 249 deletions(-)
delete mode 100644 arch/arm/include/asm/arch-at91/at91sam9261_matrix.h
delete mode 100644 board/atmel/at91sam9261ek/config.mk
-------------------------
Kind regards,
Remy
^ permalink raw reply [flat|nested] 12+ messages in thread