* [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete
@ 2011-05-23 16:14 Fabio Estevam
2011-05-23 16:14 ` [U-Boot] [PATCH v5 2/4] MX5: Add iomux structure Fabio Estevam
[not found] ` <BANLkTin_6dypOyhZW6uw-=jyvScoDVb9Hg@mail.gmail.com>
0 siblings, 2 replies; 6+ messages in thread
From: Fabio Estevam @ 2011-05-23 16:14 UTC (permalink / raw)
To: u-boot
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v4:
- Change the definition of WEIM single-bit field
Changes since v3:
- No changes
Changes since v2:
- Add CS1_BASE_ADDR for MX51
- Add WEIM Registers
arch/arm/include/asm/arch-mx5/imx-regs.h | 131 ++++++++++++++++++++++++++++--
1 files changed, 125 insertions(+), 6 deletions(-)
diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
index a1849f8..e136607 100644
--- a/arch/arm/include/asm/arch-mx5/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
@@ -32,6 +32,7 @@
#define CSD0_BASE_ADDR 0x90000000
#define CSD1_BASE_ADDR 0xA0000000
#define NFC_BASE_ADDR_AXI 0xCFFF0000
+#define CS1_BASE_ADDR 0xB8000000
#elif defined(CONFIG_MX53)
#define IPU_CTRL_BASE_ADDR 0x18000000
#define SPBA0_BASE_ADDR 0x50000000
@@ -41,6 +42,7 @@
#define CSD1_BASE_ADDR 0xB0000000
#define NFC_BASE_ADDR_AXI 0xF7FF0000
#define IRAM_BASE_ADDR 0xF8000000
+#define CS1_BASE_ADDR 0xF4000000
#else
#error "CPU_TYPE not defined"
#endif
@@ -129,6 +131,90 @@
#define SAHARA_BASE_ADDR (AIPS2_BASE_ADDR + 0x000F8000)
/*
+ * WEIM CSnGCR1
+ */
+#define CSEN 1
+#define SWR (1 << 1)
+#define SRD (1 << 2)
+#define MUM (1 << 3)
+#define WFL (1 << 4)
+#define RFL (1 << 5)
+#define CRE (1 << 6)
+#define CREP (1 << 7)
+#define BL(x) (((x) & 0x7) << 8)
+#define WC (1 << 11)
+#define BCD(x) (((x) & 0x3) << 12)
+#define BCS(x) (((x) & 0x3) << 14)
+#define DSZ(x) (((x) & 0x7) << 16)
+#define SP (1 << 19)
+#define CSREC(x) (((x) & 0x7) << 20)
+#define AUS (1 << 23)
+#define GBC(x) (((x) & 0x7) << 24)
+#define WP (1 << 27)
+#define PSZ(x) (((x) & 0x0f << 28)
+
+/*
+ * WEIM CSnGCR2
+ */
+#define ADH(x) (((x) & 0x3))
+#define DAPS(x) (((x) & 0x0f << 4)
+#define DAE (1 << 8)
+#define DAP (1 << 9)
+#define MUX16_BYP (1 << 12)
+
+/*
+ * WEIM CSnRCR1
+ */
+#define RCSN(x) (((x) & 0x7))
+#define RCSA(x) (((x) & 0x7) << 4)
+#define OEN(x) (((x) & 0x7) << 8)
+#define OEA(x) (((x) & 0x7) << 12)
+#define RADVN(x) (((x) & 0x7) << 16)
+#define RAL (1 << 19)
+#define RADVA(x) (((x) & 0x7) << 20)
+#define RWSC(x) (((x) & 0x3f) << 24)
+
+/*
+ * WEIM CSnRCR2
+ */
+#define RBEN(x) (((x) & 0x7))
+#define RBE (1 << 3)
+#define RBEA(x) (((x) & 0x7) << 4)
+#define RL(x) (((x) & 0x3) << 8)
+#define PAT(x) (((x) & 0x7) << 12)
+#define APR (1 << 15)
+
+/*
+ * WEIM CSnWCR1
+ */
+#define WCSN(x) (((x) & 0x7))
+#define WCSA(x) (((x) & 0x7) << 3)
+#define WEN(x) (((x) & 0x7) << 6)
+#define WEA(x) (((x) & 0x7) << 9)
+#define WBEN(x) (((x) & 0x7) << 12)
+#define WBEA(x) (((x) & 0x7) << 15)
+#define WADVN(x) (((x) & 0x7) << 18)
+#define WADVA(x) (((x) & 0x7) << 21)
+#define WWSC(x) (((x) & 0x3f) << 24)
+#define WBED1 (1 << 30)
+#define WAL (1 << 31)
+
+/*
+ * WEIM CSnWCR2
+ */
+#define WBED 1
+
+/*
+ * WEIM WCR
+ */
+#define BCM 1
+#define GBCD(x) (((x) & 0x3) << 1)
+#define INTEN (1 << 4)
+#define INTPOL (1 << 5)
+#define WDOG_EN (1 << 8)
+#define WDOG_LIMIT(x) (((x) & 0x3) << 9)
+
+/*
* Number of GPIO pins per port
*/
#define GPIO_NUM_PIN 32
@@ -231,12 +317,45 @@ struct clkctl {
/* WEIM registers */
struct weim {
- u32 csgcr1;
- u32 csgcr2;
- u32 csrcr1;
- u32 csrcr2;
- u32 cswcr1;
- u32 cswcr2;
+ u32 cs0gcr1;
+ u32 cs0gcr2;
+ u32 cs0rcr1;
+ u32 cs0rcr2;
+ u32 cs0wcr1;
+ u32 cs0wcr2;
+ u32 cs1gcr1;
+ u32 cs1gcr2;
+ u32 cs1rcr1;
+ u32 cs1rcr2;
+ u32 cs1wcr1;
+ u32 cs1wcr2;
+ u32 cs2gcr1;
+ u32 cs2gcr2;
+ u32 cs2rcr1;
+ u32 cs2rcr2;
+ u32 cs2wcr1;
+ u32 cs2wcr2;
+ u32 cs3gcr1;
+ u32 cs3gcr2;
+ u32 cs3rcr1;
+ u32 cs3rcr2;
+ u32 cs3wcr1;
+ u32 cs3wcr2;
+ u32 cs4gcr1;
+ u32 cs4gcr2;
+ u32 cs4rcr1;
+ u32 cs4rcr2;
+ u32 cs4wcr1;
+ u32 cs4wcr2;
+ u32 cs5gcr1;
+ u32 cs5gcr2;
+ u32 cs5rcr1;
+ u32 cs5rcr2;
+ u32 cs5wcr1;
+ u32 cs5wcr2;
+ u32 wcr;
+ u32 wiar;
+ u32 ear;
};
/* GPIO Registers */
--
1.6.0.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v5 2/4] MX5: Add iomux structure
2011-05-23 16:14 [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete Fabio Estevam
@ 2011-05-23 16:14 ` Fabio Estevam
2011-05-23 16:14 ` [U-Boot] [PATCH v5 3/4] MX5: Introduce a function for setting the chip select size Fabio Estevam
[not found] ` <BANLkTin_6dypOyhZW6uw-=jyvScoDVb9Hg@mail.gmail.com>
1 sibling, 1 reply; 6+ messages in thread
From: Fabio Estevam @ 2011-05-23 16:14 UTC (permalink / raw)
To: u-boot
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v4:
- No changes
Changes since v3:
- No changes
Changes since v2:
- Distinguish iomuxc struct between MX51 and MX53
arch/arm/include/asm/arch-mx5/imx-regs.h | 23 +++++++++++++++++++++++
1 files changed, 23 insertions(+), 0 deletions(-)
diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
index b65b11f..3c61c7f 100644
--- a/arch/arm/include/asm/arch-mx5/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
@@ -358,6 +358,29 @@ struct weim {
u32 ear;
};
+#if defined(CONFIG_MX51)
+struct iomuxc {
+ u32 gpr0;
+ u32 gpr1;
+ u32 omux0;
+ u32 omux1;
+ u32 omux2;
+ u32 omux3;
+ u32 omux4;
+};
+#elif defined(CONFIG_MX53)
+struct iomuxc {
+ u32 gpr0;
+ u32 gpr1;
+ u32 gpr2;
+ u32 omux0;
+ u32 omux1;
+ u32 omux2;
+ u32 omux3;
+ u32 omux4;
+};
+#endif
+
/* GPIO Registers */
struct gpio_regs {
u32 gpio_dr;
--
1.6.0.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v5 3/4] MX5: Introduce a function for setting the chip select size
2011-05-23 16:14 ` [U-Boot] [PATCH v5 2/4] MX5: Add iomux structure Fabio Estevam
@ 2011-05-23 16:14 ` Fabio Estevam
2011-05-23 16:14 ` [U-Boot] [PATCH v5 4/4] MX53: Add initial support for MX53ARD Fabio Estevam
0 siblings, 1 reply; 6+ messages in thread
From: Fabio Estevam @ 2011-05-23 16:14 UTC (permalink / raw)
To: u-boot
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v4:
- No changes
Changes since v3:
- Print the chip size in the case of error
arch/arm/cpu/armv7/mx5/soc.c | 30 +++++++++++++++++++++++++++++
arch/arm/include/asm/arch-mx5/imx-regs.h | 5 ++++
arch/arm/include/asm/arch-mx5/sys_proto.h | 2 +-
3 files changed, 36 insertions(+), 1 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx5/soc.c b/arch/arm/cpu/armv7/mx5/soc.c
index 40b8b56..e599df8 100644
--- a/arch/arm/cpu/armv7/mx5/soc.c
+++ b/arch/arm/cpu/armv7/mx5/soc.c
@@ -163,6 +163,36 @@ int cpu_mmc_init(bd_t *bis)
#endif
}
+void set_chipselect_size(int const cs_size)
+{
+ unsigned int reg;
+ struct iomuxc *iomuxc_regs = (struct weim *)IOMUXC_BASE_ADDR;
+ reg = readl(&iomuxc_regs->gpr1);
+
+ switch (cs_size) {
+ case CS0_128:
+ reg &= ~0x7; /* CS0=128MB, CS1=0, CS2=0, CS3=0 */
+ reg |= 0x5;
+ break;
+ case CS0_64M_CS1_64M:
+ reg &= ~0x3F; /* CS0=64MB, CS1=64MB, CS2=0, CS3=0 */
+ reg |= 0x1B;
+ break;
+ case CS0_64M_CS1_32M_CS2_32M:
+ reg &= ~0x1FF; /* CS0=64MB, CS1=32MB, CS2=32MB, CS3=0 */
+ reg |= 0x4B;
+ break;
+ case CS0_32M_CS1_32M_CS2_32M_CS3_32M:
+ reg &= ~0xFFF; /* CS0=32MB, CS1=32MB, CS2=32MB, CS3=32MB */
+ reg |= 0x249;
+ break;
+ default:
+ printf("Unknown chip select size: %d\n", cs_size);
+ break;
+ }
+
+ writel(reg, &iomuxc_regs->gpr1);
+}
void reset_cpu(ulong addr)
{
diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
index 9d2046a..5163614 100644
--- a/arch/arm/include/asm/arch-mx5/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
@@ -214,6 +214,11 @@
#define WDOG_EN(x) ((x) << 8)
#define WDOG_LIMIT(x) (((x) & 0x3) << 9)
+#define CS0_128 0
+#define CS0_64M_CS1_64M 1
+#define CS0_64M_CS1_32M_CS2_32M 2
+#define CS0_32M_CS1_32M_CS2_32M_CS3_32M 3
+
/*
* Number of GPIO pins per port
*/
diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h
index f687503..ce63675 100644
--- a/arch/arm/include/asm/arch-mx5/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx5/sys_proto.h
@@ -27,5 +27,5 @@
u32 get_cpu_rev(void);
#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev)
void sdelay(unsigned long);
-
+void set_chipselect_size(int const);
#endif
--
1.6.0.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v5 4/4] MX53: Add initial support for MX53ARD
2011-05-23 16:14 ` [U-Boot] [PATCH v5 3/4] MX5: Introduce a function for setting the chip select size Fabio Estevam
@ 2011-05-23 16:14 ` Fabio Estevam
0 siblings, 0 replies; 6+ messages in thread
From: Fabio Estevam @ 2011-05-23 16:14 UTC (permalink / raw)
To: u-boot
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v4:
- Changed the weim cs1 settings for the single-bit fields
- Removed unused 'reg' variable inside weim_smc911x_iomux()
- Made void weim_cs1_settings() and weim_smc911x_iomux() static
Changes since v3:
- No changes
Changes since v2:
- Use macros for setting up weim register
- Use set_chipselect_size function
- Rename the file to imximage_dd3.cfg to make explicit the DDR type.
MAINTAINERS | 1 +
board/freescale/mx53ard/Makefile | 48 +++++
board/freescale/mx53ard/imximage_dd3.cfg | 96 ++++++++++
board/freescale/mx53ard/mx53ard.c | 306 ++++++++++++++++++++++++++++++
boards.cfg | 1 +
include/configs/mx53ard.h | 198 +++++++++++++++++++
6 files changed, 650 insertions(+), 0 deletions(-)
create mode 100644 board/freescale/mx53ard/Makefile
create mode 100644 board/freescale/mx53ard/imximage_dd3.cfg
create mode 100644 board/freescale/mx53ard/mx53ard.c
create mode 100644 include/configs/mx53ard.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 07237e3..b63f53f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
Fabio Estevam <fabio.estevam@freescale.com>
mx31pdk i.MX31
+ mx53ard i.MX53
mx53smd i.MX53
Peter Figuli <peposh@etc.sk>
diff --git a/board/freescale/mx53ard/Makefile b/board/freescale/mx53ard/Makefile
new file mode 100644
index 0000000..c48ece8
--- /dev/null
+++ b/board/freescale/mx53ard/Makefile
@@ -0,0 +1,48 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := mx53ard.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx53ard/imximage_dd3.cfg b/board/freescale/mx53ard/imximage_dd3.cfg
new file mode 100644
index 0000000..0f298ab
--- /dev/null
+++ b/board/freescale/mx53ard/imximage_dd3.cfg
@@ -0,0 +1,96 @@
+#
+# (C) Copyright 2009
+# Stefano Babic DENX Software Engineering sbabic at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not write to the Free Software
+# Foundation Inc. 51 Franklin Street Fifth Floor Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.imxmage for more details about how-to configure
+# and create imximage boot image
+#
+# The syntax is taken as close as possible with the kwbimage
+
+# image version
+
+IMAGE_VERSION 2
+
+# Boot Device : one of
+# spi, sd (the board has no nand neither onenand)
+
+BOOT_FROM sd
+
+# Device Configuration Data (DCD)
+#
+# Each entry must have the format:
+# Addr-type Address Value
+#
+# where:
+# Addr-type register length (1,2 or 4 bytes)
+# Address absolute address of the register
+# value value to be stored in the register
+DATA 4 0x53fa8554 0x00300000
+DATA 4 0x53fa8558 0x00300040
+DATA 4 0x53fa8560 0x00300000
+DATA 4 0x53fa8564 0x00300040
+DATA 4 0x53fa8568 0x00300040
+DATA 4 0x53fa8570 0x00300000
+DATA 4 0x53fa8574 0x00300000
+DATA 4 0x53fa8578 0x00300000
+DATA 4 0x53fa857c 0x00300040
+DATA 4 0x53fa8580 0x00300040
+DATA 4 0x53fa8584 0x00300000
+DATA 4 0x53fa8588 0x00300000
+DATA 4 0x53fa8590 0x00300040
+DATA 4 0x53fa8594 0x00300000
+DATA 4 0x53fa86f0 0x00300000
+DATA 4 0x53fa86f4 0x00000000
+DATA 4 0x53fa86fc 0x00000000
+DATA 4 0x53fa8714 0x00000000
+DATA 4 0x53fa8718 0x00300000
+DATA 4 0x53fa871c 0x00300000
+DATA 4 0x53fa8720 0x00300000
+DATA 4 0x53fa8724 0x04000000
+DATA 4 0x53fa8728 0x00300000
+DATA 4 0x53fa872c 0x00300000
+DATA 4 0x63fd9088 0x35343535
+DATA 4 0x63fd9090 0x4d444c44
+DATA 4 0x63fd907c 0x01370138
+DATA 4 0x63fd9080 0x013b013c
+DATA 4 0x63fd9018 0x00011740
+DATA 4 0x63fd9000 0xc3190000
+DATA 4 0x63fd900c 0x9f5152e3
+DATA 4 0x63fd9010 0xb68e8a63
+DATA 4 0x63fd9014 0x01ff00db
+DATA 4 0x63fd902c 0x000026d2
+DATA 4 0x63fd9030 0x009f0e21
+DATA 4 0x63fd9008 0x12273030
+DATA 4 0x63fd9004 0x0002002d
+DATA 4 0x63fd901c 0x00008032
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00028031
+DATA 4 0x63fd901c 0x092080b0
+DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd901c 0x0000803a
+DATA 4 0x63fd901c 0x0000803b
+DATA 4 0x63fd901c 0x00028039
+DATA 4 0x63fd901c 0x09208138
+DATA 4 0x63fd901c 0x04008048
+DATA 4 0x63fd9020 0x00001800
+DATA 4 0x63fd9040 0x04b80003
+DATA 4 0x63fd9058 0x00022227
+DATA 4 0x63fd901C 0x00000000
diff --git a/board/freescale/mx53ard/mx53ard.c b/board/freescale/mx53ard/mx53ard.c
new file mode 100644
index 0000000..7bc9c2e
--- /dev/null
+++ b/board/freescale/mx53ard/mx53ard.c
@@ -0,0 +1,306 @@
+/*
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx5x_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/errno.h>
+#include <netdev.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <mxc_gpio.h>
+
+#define ETHERNET_INT (1 * 32 + 31) /* GPIO2_31 */
+
+DECLARE_GLOBAL_DATA_PTR;
+
+u32 get_board_rev(void)
+{
+ return get_cpu_rev();
+}
+
+int dram_init(void)
+{
+ u32 size1, size2;
+
+ size1 = get_ram_size((volatile void *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+ size2 = get_ram_size((volatile void *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
+
+ gd->ram_size = size1 + size2;
+
+ return 0;
+}
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+}
+
+static void setup_iomux_uart(void)
+{
+ /* UART1 RXD */
+ mxc_request_iomux(MX53_PIN_ATA_DMACK, IOMUX_CONFIG_ALT3);
+ mxc_iomux_set_pad(MX53_PIN_ATA_DMACK,
+ PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+ PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+ PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU |
+ PAD_CTL_ODE_OPENDRAIN_ENABLE);
+ mxc_iomux_set_input(MX53_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, 0x3);
+
+ /* UART1 TXD */
+ mxc_request_iomux(MX53_PIN_ATA_DIOW, IOMUX_CONFIG_ALT3);
+ mxc_iomux_set_pad(MX53_PIN_ATA_DIOW,
+ PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+ PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+ PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU |
+ PAD_CTL_ODE_OPENDRAIN_ENABLE);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[2] = {
+ {MMC_SDHC1_BASE_ADDR, 1 },
+ {MMC_SDHC2_BASE_ADDR, 1 },
+};
+
+int board_mmc_getcd(u8 *cd, struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+ if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
+ *cd = mxc_gpio_get(1); /*GPIO1_1*/
+ else
+ *cd = mxc_gpio_get(4); /*GPIO1_4*/
+
+ return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ u32 index;
+ s32 status = 0;
+
+ for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
+ switch (index) {
+ case 0:
+ mxc_request_iomux(MX53_PIN_SD1_CMD, IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD1_CLK, IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD1_DATA0,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD1_DATA1,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD1_DATA2,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD1_DATA3,
+ IOMUX_CONFIG_ALT0);
+
+ mxc_iomux_set_pad(MX53_PIN_SD1_CMD, 0x1E4);
+ mxc_iomux_set_pad(MX53_PIN_SD1_CLK, 0xD4);
+ mxc_iomux_set_pad(MX53_PIN_SD1_DATA0, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_SD1_DATA1, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_SD1_DATA2, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_SD1_DATA3, 0x1D4);
+ break;
+ case 1:
+ mxc_request_iomux(MX53_PIN_SD2_CMD,
+ IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION);
+ mxc_request_iomux(MX53_PIN_SD2_CLK,
+ IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION);
+ mxc_request_iomux(MX53_PIN_SD2_DATA0,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD2_DATA1,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD2_DATA2,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_SD2_DATA3,
+ IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_ATA_DATA12,
+ IOMUX_CONFIG_ALT2);
+ mxc_request_iomux(MX53_PIN_ATA_DATA13,
+ IOMUX_CONFIG_ALT2);
+ mxc_request_iomux(MX53_PIN_ATA_DATA14,
+ IOMUX_CONFIG_ALT2);
+ mxc_request_iomux(MX53_PIN_ATA_DATA15,
+ IOMUX_CONFIG_ALT2);
+
+ mxc_iomux_set_pad(MX53_PIN_SD2_CMD, 0x1E4);
+ mxc_iomux_set_pad(MX53_PIN_SD2_CLK, 0xD4);
+ mxc_iomux_set_pad(MX53_PIN_SD2_DATA0, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_SD2_DATA1, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_SD2_DATA2, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_SD2_DATA3, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_ATA_DATA12, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_ATA_DATA13, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_ATA_DATA14, 0x1D4);
+ mxc_iomux_set_pad(MX53_PIN_ATA_DATA15, 0x1D4);
+ break;
+ default:
+ printf("Warning: you configured more ESDHC controller"
+ "(%d) as supported by the board(2)\n",
+ CONFIG_SYS_FSL_ESDHC_NUM);
+ return status;
+ }
+ status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
+ }
+
+ return status;
+}
+#endif
+
+static void weim_smc911x_iomux()
+{
+ /* ETHERNET_INT as GPIO2_31 */
+ mxc_request_iomux(MX53_PIN_EIM_EB3, IOMUX_CONFIG_ALT1);
+ mxc_gpio_direction(ETHERNET_INT, MXC_GPIO_DIRECTION_IN);
+
+ /* Data bus */
+ mxc_request_iomux(MX53_PIN_EIM_D16, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D16, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D17, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D17, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D18, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D18, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D19, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D19, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D20, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D20, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D21, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D21, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D22, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D22, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D23, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D23, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D24, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D24, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D25, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D25, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D26, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D26, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D27, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D27, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D28, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D28, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D29, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D29, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D30, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D30, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_D31, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_D31, 0xA4);
+
+ /* Address lines */
+ mxc_request_iomux(MX53_PIN_EIM_DA0, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA0, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_DA1, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA1, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_DA2, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA2, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_DA3, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA3, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_DA4, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA4, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_DA5, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA5, 0xA4);
+
+ mxc_request_iomux(MX53_PIN_EIM_DA6, IOMUX_CONFIG_ALT0);
+ mxc_iomux_set_pad(MX53_PIN_EIM_DA6, 0xA4);
+
+ /* other EIM signals for ethernet */
+ mxc_request_iomux(MX53_PIN_EIM_OE, IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_EIM_RW, IOMUX_CONFIG_ALT0);
+ mxc_request_iomux(MX53_PIN_EIM_CS1, IOMUX_CONFIG_ALT0);
+}
+
+static void weim_cs1_settings()
+{
+ struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;
+
+ writel(MX53ARD_CS1GCR1, &weim_regs->cs1gcr1);
+ writel(0x0, &weim_regs->cs1gcr2);
+ writel(MX53ARD_CS1RCR1, &weim_regs->cs1rcr1);
+ writel(MX53ARD_CS1RCR2, &weim_regs->cs1rcr2);
+ writel(MX53ARD_CS1WCR1, &weim_regs->cs1wcr1);
+ writel(0x0, &weim_regs->cs1wcr2);
+ writel(0x0, &weim_regs->wcr);
+
+ set_chipselect_size(CS0_64M_CS1_64M);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ return 0;
+}
+
+int board_init(void)
+{
+ gd->bd->bi_arch_number = MACH_TYPE_MX53_ARD;
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+
+ weim_smc911x_iomux();
+ weim_cs1_settings();
+
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}
+
+int checkboard(void)
+{
+ puts("Board: MX53ARD\n");
+
+ return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index 9339981..a616f29 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -124,6 +124,7 @@ dkb arm arm926ejs - Marvell pantheon
ca9x4_ct_vxp arm armv7 vexpress armltd
efikamx arm armv7 efikamx - mx5
mx51evk arm armv7 mx51evk freescale mx5 mx51evk:IMX_CONFIG=board/freescale/mx51evk/imximage.cfg
+mx53ard arm armv7 mx53ard freescale mx5 mx53ard:IMX_CONFIG=board/freescale/mx53ard/imximage_dd3.cfg
mx53evk arm armv7 mx53evk freescale mx5 mx53evk:IMX_CONFIG=board/freescale/mx53evk/imximage.cfg
mx53loco arm armv7 mx53loco freescale mx5 mx53loco:IMX_CONFIG=board/freescale/mx53loco/imximage.cfg
mx53smd arm armv7 mx53smd freescale mx5 mx53smd:IMX_CONFIG=board/freescale/mx53smd/imximage.cfg
diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h
new file mode 100644
index 0000000..c872510
--- /dev/null
+++ b/include/configs/mx53ard.h
@@ -0,0 +1,198 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the MX53ARD Freescale board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MX53
+
+#define CONFIG_SYS_MX5_HCLK 24000000
+#define CONFIG_SYS_MX5_CLK32 32768
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_L2_OFF
+
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_REVISION_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_SYS_MX53_UART1
+
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_HARD_I2C
+#define CONFIG_I2C_MXC
+#define CONFIG_SYS_I2C_MX53_PORT2
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 0xfe
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_ESDHC_NUM 2
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* Eth Configs */
+#define CONFIG_HAS_ETH1
+#define CONFIG_NET_MULTI
+#define CONFIG_MII
+#define CONFIG_MII_GASKET
+#define CONFIG_DISCOVER_PHY
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_PRIME "smc911x"
+
+/*Support LAN9217*/
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_SMC911X_BASE CS1_BASE_ADDR
+
+#define CONFIG_LOADADDR 0x70800000 /* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE 0x77800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "uimage=uImage\0" \
+ "mmcdev=0\0" \
+ "mmcpart=2\0" \
+ "mmcroot=/dev/mmcblk0p3 rw\0" \
+ "mmcrootfstype=ext3 rootwait\0" \
+ "mmcargs=setenv bootargs console=ttymxc0,${baudrate} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm\0" \
+ "netargs=setenv bootargs console=ttymxc0,${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "dhcp ${uimage}; bootm\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc rescan ${mmcdev}; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT "MX53ARD U-Boot > "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x70000000
+#define CONFIG_SYS_MEMTEST_END 0x70010000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_CMDLINE_EDITING
+
+/* Stack sizes */
+#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 2
+#define PHYS_SDRAM_1 CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE (512 * 1024 * 1024)
+#define PHYS_SDRAM_2 CSD1_BASE_ADDR
+#define PHYS_SDRAM_2_SIZE (512 * 1024 * 1024)
+#define PHYS_SDRAM_SIZE (PHYS_SDRAM_1_SIZE + PHYS_SDRAM_2_SIZE)
+
+#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_OF_LIBFDT
+
+#define MX53ARD_CS1GCR1 (CSEN | DSZ(2))
+#define MX53ARD_CS1RCR1 (RCSN(2) | OEN (1) | RWSC(22))
+#define MX53ARD_CS1RCR2 RBEN(2)
+#define MX53ARD_CS1WCR1 (WCSN(2) | WEN(2) | WBEN(2) | WWSC(22))
+
+#endif /* __CONFIG_H */
--
1.6.0.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete
[not found] ` <BANLkTin_6dypOyhZW6uw-=jyvScoDVb9Hg@mail.gmail.com>
@ 2011-05-27 13:04 ` Stefano Babic
2011-06-07 13:31 ` Stefano Babic
1 sibling, 0 replies; 6+ messages in thread
From: Stefano Babic @ 2011-05-27 13:04 UTC (permalink / raw)
To: u-boot
On 05/27/2011 02:40 PM, Fabio Estevam wrote:
> Hi Stefano,
>
> Does this patch series look fine now?
>
Hi Fabio,
I have no comments about your last post. However, as you posted the
first patchset for the MX53ARD when the merge window was already closed
(not last Wolfgang has already published the 2011.06-rc1), I will put
the MX53ARD (including the WEIM patch) into u-boot-imx, next branch, and
not directly into u-boot-imx/master.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete
[not found] ` <BANLkTin_6dypOyhZW6uw-=jyvScoDVb9Hg@mail.gmail.com>
2011-05-27 13:04 ` [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete Stefano Babic
@ 2011-06-07 13:31 ` Stefano Babic
1 sibling, 0 replies; 6+ messages in thread
From: Stefano Babic @ 2011-06-07 13:31 UTC (permalink / raw)
To: u-boot
On 05/27/2011 02:40 PM, Fabio Estevam wrote:
> Hi Stefano,
>
> Does this patch series look fine now?
>
Hi Fabio,
I see some warnings that must be dropped before putting your patches
into the mainline:
Configuring for mx53ard - Board: mx53ard, Options:
IMX_CONFIG=board/freescale/mx53ard/imximage_dd3.cfg
soc.c: In function 'set_chipselect_size':
soc.c:169: warning: initialization from incompatible pointer type
In fact:
struct iomuxc *iomuxc_regs = (struct weim *)IOMUXC_BASE_ADDR;
^-- this should be struct iomuxc
mx53ard.c:176: warning: function declaration isn't a prototype
mx53ard.c:259: warning: function declaration isn't a prototype
due to static void weim_smc911x_iomux() instead of static void
weim_smc911x_iomux(void).
Can you fix them ?
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2011-06-07 13:31 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-05-23 16:14 [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete Fabio Estevam
2011-05-23 16:14 ` [U-Boot] [PATCH v5 2/4] MX5: Add iomux structure Fabio Estevam
2011-05-23 16:14 ` [U-Boot] [PATCH v5 3/4] MX5: Introduce a function for setting the chip select size Fabio Estevam
2011-05-23 16:14 ` [U-Boot] [PATCH v5 4/4] MX53: Add initial support for MX53ARD Fabio Estevam
[not found] ` <BANLkTin_6dypOyhZW6uw-=jyvScoDVb9Hg@mail.gmail.com>
2011-05-27 13:04 ` [U-Boot] [PATCH v5 1/4] MX5: Make the weim structure complete Stefano Babic
2011-06-07 13:31 ` Stefano Babic
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.