* [PATCH 1/3] MIPS: Alchemy: abstract USB block control register access
2011-05-24 8:01 [PATCH 0/3] MIPS: Alchemy: USB updates and more cleanups Manuel Lauss
@ 2011-05-24 8:01 ` Manuel Lauss
2011-05-24 8:01 ` [PATCH 2/3] MIPS: Alchemy: rewrite USB platform setup Manuel Lauss
2011-05-24 8:01 ` [PATCH 3/3] MIPS: Alchemy: more base address cleanup Manuel Lauss
2 siblings, 0 replies; 4+ messages in thread
From: Manuel Lauss @ 2011-05-24 8:01 UTC (permalink / raw)
To: Ralf Baechle; +Cc: Linux-MIPS, Manuel Lauss, Linux-USB
Au1200 and Au1300 have one or more registers which control access
to the usb blocks as well as PHY configuration. I don't want
the OHCI/EHCI glues to know about the different registers and bits,
a new file hides the gory details of USB configuration from them.
Cc: Linux-USB <linux-usb@vger.kernel.org>
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/common/Makefile | 2 +-
arch/mips/alchemy/common/dma.c | 12 +-
arch/mips/alchemy/common/power.c | 42 ----
arch/mips/alchemy/common/usb.c | 345 ++++++++++++++++++++++++++++
arch/mips/include/asm/mach-au1x00/au1000.h | 84 ++------
drivers/usb/host/ehci-au1xxx.c | 77 +------
drivers/usb/host/ohci-au1xxx.c | 110 +--------
7 files changed, 390 insertions(+), 282 deletions(-)
create mode 100644 arch/mips/alchemy/common/usb.c
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
index 27811fe..575db47 100644
--- a/arch/mips/alchemy/common/Makefile
+++ b/arch/mips/alchemy/common/Makefile
@@ -6,7 +6,7 @@
#
obj-y += prom.o time.o clocks.o platform.o power.o setup.o \
- sleeper.o dma.o dbdma.o
+ sleeper.o dma.o dbdma.o usb.o
obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o
diff --git a/arch/mips/alchemy/common/dma.c b/arch/mips/alchemy/common/dma.c
index 347980e..6652a23 100644
--- a/arch/mips/alchemy/common/dma.c
+++ b/arch/mips/alchemy/common/dma.c
@@ -88,12 +88,12 @@ static const struct dma_dev {
{ AU1000_AC97_PHYS_ADDR + 0x08, DMA_DW16 | DMA_DR }, /* AC97 RX c */
{ AU1000_UART3_PHYS_ADDR + 0x04, DMA_DW8 | DMA_NC }, /* UART3_TX */
{ AU1000_UART3_PHYS_ADDR + 0x00, DMA_DW8 | DMA_NC | DMA_DR }, /* UART3_RX */
- { AU1000_USBD_PHYS_ADDR + 0x00, DMA_DW8 | DMA_NC | DMA_DR }, /* EP0RD */
- { AU1000_USBD_PHYS_ADDR + 0x04, DMA_DW8 | DMA_NC }, /* EP0WR */
- { AU1000_USBD_PHYS_ADDR + 0x08, DMA_DW8 | DMA_NC }, /* EP2WR */
- { AU1000_USBD_PHYS_ADDR + 0x0c, DMA_DW8 | DMA_NC }, /* EP3WR */
- { AU1000_USBD_PHYS_ADDR + 0x10, DMA_DW8 | DMA_NC | DMA_DR }, /* EP4RD */
- { AU1000_USBD_PHYS_ADDR + 0x14, DMA_DW8 | DMA_NC | DMA_DR }, /* EP5RD */
+ { AU1000_USB_UDC_PHYS_ADDR + 0x00, DMA_DW8 | DMA_NC | DMA_DR }, /* EP0RD */
+ { AU1000_USB_UDC_PHYS_ADDR + 0x04, DMA_DW8 | DMA_NC }, /* EP0WR */
+ { AU1000_USB_UDC_PHYS_ADDR + 0x08, DMA_DW8 | DMA_NC }, /* EP2WR */
+ { AU1000_USB_UDC_PHYS_ADDR + 0x0c, DMA_DW8 | DMA_NC }, /* EP3WR */
+ { AU1000_USB_UDC_PHYS_ADDR + 0x10, DMA_DW8 | DMA_NC | DMA_DR }, /* EP4RD */
+ { AU1000_USB_UDC_PHYS_ADDR + 0x14, DMA_DW8 | DMA_NC | DMA_DR }, /* EP5RD */
/* on Au1500, these 2 are DMA_REQ2/3 (GPIO208/209) instead! */
{ AU1000_I2S_PHYS_ADDR + 0x00, DMA_DW32 | DMA_NC}, /* I2S TX */
{ AU1000_I2S_PHYS_ADDR + 0x00, DMA_DW32 | DMA_NC | DMA_DR}, /* I2S RX */
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index 647e518..f1244f05 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -49,7 +49,6 @@
* We only have to save/restore registers that aren't otherwise
* done as part of a driver pm_* function.
*/
-static unsigned int sleep_usb[2];
static unsigned int sleep_sys_clocks[5];
static unsigned int sleep_sys_pinfunc;
static unsigned int sleep_static_memctlr[4][3];
@@ -57,31 +56,6 @@ static unsigned int sleep_static_memctlr[4][3];
static void save_core_regs(void)
{
-#ifndef CONFIG_SOC_AU1200
- /* Shutdown USB host/device. */
- sleep_usb[0] = au_readl(USB_HOST_CONFIG);
-
- /* There appears to be some undocumented reset register.... */
- au_writel(0, 0xb0100004);
- au_sync();
- au_writel(0, USB_HOST_CONFIG);
- au_sync();
-
- sleep_usb[1] = au_readl(USBD_ENABLE);
- au_writel(0, USBD_ENABLE);
- au_sync();
-
-#else /* AU1200 */
-
- /* enable access to OTG mmio so we can save OTG CAP/MUX.
- * FIXME: write an OTG driver and move this stuff there!
- */
- au_writel(au_readl(USB_MSR_BASE + 4) | (1 << 6), USB_MSR_BASE + 4);
- au_sync();
- sleep_usb[0] = au_readl(0xb4020020); /* OTG_CAP */
- sleep_usb[1] = au_readl(0xb4020024); /* OTG_MUX */
-#endif
-
/* Clocks and PLLs. */
sleep_sys_clocks[0] = au_readl(SYS_FREQCTRL0);
sleep_sys_clocks[1] = au_readl(SYS_FREQCTRL1);
@@ -125,22 +99,6 @@ static void restore_core_regs(void)
au_writel(sleep_sys_pinfunc, SYS_PINFUNC);
au_sync();
-#ifndef CONFIG_SOC_AU1200
- au_writel(sleep_usb[0], USB_HOST_CONFIG);
- au_writel(sleep_usb[1], USBD_ENABLE);
- au_sync();
-#else
- /* enable access to OTG memory */
- au_writel(au_readl(USB_MSR_BASE + 4) | (1 << 6), USB_MSR_BASE + 4);
- au_sync();
-
- /* restore OTG caps and port mux. */
- au_writel(sleep_usb[0], 0xb4020020 + 0); /* OTG_CAP */
- au_sync();
- au_writel(sleep_usb[1], 0xb4020020 + 4); /* OTG_MUX */
- au_sync();
-#endif
-
/* Restore the static memory controller configuration. */
au_writel(sleep_static_memctlr[0][0], MEM_STCFG0);
au_writel(sleep_static_memctlr[0][1], MEM_STTIME0);
diff --git a/arch/mips/alchemy/common/usb.c b/arch/mips/alchemy/common/usb.c
new file mode 100644
index 0000000..559a034
--- /dev/null
+++ b/arch/mips/alchemy/common/usb.c
@@ -0,0 +1,345 @@
+/*
+ * USB block power/access management abstraction.
+ *
+ *
+ * Au1000+: the OHCI block control register is at the far end of the
+ * OHCI memory area. Au1550 has OHCI on different base address.
+ * The Au1000 UDC is not handled because a full driver can do PM and
+ * control.
+ * Au1200: one register to control access and clocks to O/EHCI, UDC and OTG,
+ * it's the main reason for this file's existence, as I don't want
+ * every bit of glue code messing with it.
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/syscore_ops.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/* control register offsets */
+#define AU1000_USBCFG 0x7fffc
+#define AU1550_USBCFG 0x07ffc
+#define AU1200_USBCFG 0x04
+
+/* Au1000 USB block config bits */
+#define USBHEN_RD (1 << 4) /* OHCI reset-done indicator */
+#define USBHEN_CE (1 << 3) /* OHCI block clock enable */
+#define USBHEN_E (1 << 2) /* OHCI block enable */
+#define USBHEN_C (1 << 1) /* OHCI block coherency bit */
+#define USBHEN_BE (1 << 0) /* OHCI Big-Endian */
+
+/* Au1200 USB config bits */
+#define USBCFG_PFEN (1 << 31) /* prefetch enable (undoc) */
+#define USBCFG_RDCOMB (1 << 30) /* read combining (undoc) */
+#define USBCFG_UNKNOWN (5 << 20) /* unknown, must be set */
+#define USBCFG_SSD (1 << 23) /* serial short detect en */
+#define USBCFG_PPE (1 << 19) /* HS PHY PLL */
+#define USBCFG_UCE (1 << 18) /* UDC clock enable */
+#define USBCFG_ECE (1 << 17) /* EHCI clock enable */
+#define USBCFG_OCE (1 << 16) /* OHCI clock enable */
+#define USBCFG_FLA(x) (((x) & 0x3f) << 8)
+#define USBCFG_UCAM (1 << 7) /* coherent access (undoc) */
+#define USBCFG_GME (1 << 6) /* OTG mem access */
+#define USBCFG_DBE (1 << 5) /* UDC busmaster enable */
+#define USBCFG_DME (1 << 4) /* UDC mem enable */
+#define USBCFG_EBE (1 << 3) /* EHCI busmaster enable */
+#define USBCFG_EME (1 << 2) /* EHCI mem enable */
+#define USBCFG_OBE (1 << 1) /* OHCI busmaster enable */
+#define USBCFG_OME (1 << 0) /* OHCI mem enable */
+#define USBCFG_INIT_AU1200 (USBCFG_PFEN | USBCFG_RDCOMB | USBCFG_UNKNOWN |\
+ USBCFG_SSD | USBCFG_FLA(0x20) | USBCFG_UCAM | \
+ USBCFG_GME | USBCFG_DBE | USBCFG_DME | \
+ USBCFG_EBE | USBCFG_EME | USBCFG_OBE | \
+ USBCFG_OME)
+
+
+DEFINE_SPINLOCK(alchemy_usb_lock);
+
+
+static inline void __au1200_ohci_control(void __iomem *base, int enable)
+{
+ unsigned long r = __raw_readl(base + 0x04); /* USB_CFG */
+ if (enable) {
+ __raw_writel(r | USBCFG_OCE, base + 0x04);
+ wmb();
+ udelay(2000);
+ } else {
+ __raw_writel(r & ~USBCFG_OCE, base + 0x04);
+ wmb();
+ udelay(1000);
+ }
+}
+
+static inline void __au1200_ehci_control(void __iomem *base, int enable)
+{
+ unsigned long r = __raw_readl(base + 0x04); /* USB_CFG */
+ if (enable) {
+ __raw_writel(r | USBCFG_ECE | USBCFG_PPE, base + 0x04);
+ wmb();
+ udelay(1000);
+ } else {
+ if (!(r & USBCFG_UCE)) /* UDC also off? */
+ r &= ~USBCFG_PPE; /* yes: disable HS PHY PLL */
+ __raw_writel(r & ~USBCFG_ECE, base + 0x04);
+ wmb();
+ udelay(1000);
+ }
+}
+
+static inline void __au1200_udc_control(void __iomem *base, int enable)
+{
+ unsigned long r = __raw_readl(base + 0x04); /* USB_CFG */
+ if (enable) {
+ __raw_writel(r | USBCFG_UCE | USBCFG_PPE, base + 0x04);
+ wmb();
+ } else {
+ if (!(r & USBCFG_ECE)) /* EHCI also off? */
+ r &= ~USBCFG_PPE; /* yes: disable HS PHY PLL */
+ __raw_writel(r & ~USBCFG_UCE, base + 0x04);
+ wmb();
+ }
+}
+
+static inline int au1200_coherency_bug(void)
+{
+#if defined(CONFIG_DMA_COHERENT)
+ /* Au1200 AB USB does not support coherent memory */
+ if (!(read_c0_prid() & 0xff)) {
+ printk(KERN_INFO "Au1200 USB: this is chip revision AB !!\n");
+ printk(KERN_INFO "Au1200 USB: update your board or re-configure"
+ " the kernel\n");
+ return -ENODEV;
+ }
+#endif
+ return 0;
+}
+
+static inline int au1200_usb_control(int block, int enable)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1200_USB_CTL_PHYS_ADDR);
+ unsigned long flags, ret = 0;
+
+ spin_lock_irqsave(&alchemy_usb_lock, flags);
+ switch (block) {
+ case ALCHEMY_USB_OHCI0:
+ ret = au1200_coherency_bug();
+ if (ret && enable)
+ goto out;
+ __au1200_ohci_control(base, enable);
+ break;
+ case ALCHEMY_USB_UDC0:
+ __au1200_udc_control(base, enable);
+ break;
+ case ALCHEMY_USB_EHCI0:
+ ret = au1200_coherency_bug();
+ if (ret && enable)
+ goto out;
+ __au1200_ehci_control(base, enable);
+ break;
+ default:
+ ret = -ENODEV;
+ }
+out:
+ spin_unlock_irqrestore(&alchemy_usb_lock, flags);
+ return ret;
+}
+
+
+/* initialize USB block(s) to a known working state */
+static inline void au1200_usb_init(void)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1200_USB_CTL_PHYS_ADDR);
+ __raw_writel(USBCFG_INIT_AU1200, base + 0x04); /* USB_CFG */
+ wmb();
+ udelay(1000);
+}
+
+static inline void au1000_usb_init(unsigned long rb, int reg)
+{
+ void __iomem *base = (void __iomem *)KSEG1ADDR(rb + reg);
+ unsigned long r = __raw_readl(base);
+
+#if defined(__BIG_ENDIAN)
+ r |= USBHEN_BE;
+#elif defined(__LITTLE_ENDIAN)
+ r |= 0;
+#endif
+ __raw_writel(r, base);
+ wmb();
+ udelay(1000);
+}
+
+
+static inline void __au1xx0_ohci_control(int enable, unsigned long rb, int creg)
+{
+ void __iomem *base = (void __iomem *)KSEG1ADDR(rb);
+ unsigned long r = __raw_readl(base + creg);
+
+ if (enable) {
+ __raw_writel(r | USBHEN_CE, base + creg);
+ wmb();
+ udelay(1000);
+ __raw_writel(r | USBHEN_CE | USBHEN_E, base + creg);
+ wmb();
+ udelay(1000);
+
+ /* wait for reset complete (read reg twice; au1500 erratum) */
+ while (__raw_readl(base + creg),
+ !(__raw_readl(base + creg) & USBHEN_RD))
+ udelay(1000);
+ } else {
+ __raw_writel(r & ~(USBHEN_CE | USBHEN_E), base + creg);
+ wmb();
+ }
+}
+
+static int au1000_usb_control(int block, int enable, unsigned long rb, int creg)
+{
+ unsigned long flags, ret = 0;
+
+ spin_lock_irqsave(&alchemy_usb_lock, flags);
+ switch (block) {
+ case ALCHEMY_USB_OHCI0:
+ __au1xx0_ohci_control(enable, rb, creg);
+ break;
+ default:
+ ret = -ENODEV;
+ }
+ spin_unlock_irqrestore(&alchemy_usb_lock, flags);
+ return ret;
+}
+
+/*
+ * alchemy_usb_control - control Alchemy on-chip USB blocks
+ * @block: USB block to target
+ * @enable: set 1 to enable a block, 0 to disable
+ */
+int alchemy_usb_control(int block, int enable)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1000:
+ case ALCHEMY_CPU_AU1500:
+ case ALCHEMY_CPU_AU1100:
+ return au1000_usb_control(block, enable,
+ AU1000_USB_OHCI_PHYS_ADDR, AU1000_USBCFG);
+ case ALCHEMY_CPU_AU1550:
+ return au1000_usb_control(block, enable,
+ AU1550_USB_OHCI_PHYS_ADDR, AU1550_USBCFG);
+ case ALCHEMY_CPU_AU1200:
+ return au1200_usb_control(block, enable);
+ }
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(alchemy_usb_control);
+
+
+static unsigned long alchemy_usb_pmdata[2];
+
+static void au1000_usb_suspend(unsigned long br, int creg)
+{
+ void __iomem *base = (void __iomem *)KSEG1ADDR(br);
+
+ alchemy_usb_pmdata[0] = __raw_readl(base + creg);
+ /* There appears to be some undocumented reset register.... */
+ __raw_writel(0, base + 0x04);
+ wmb();
+ __raw_writel(0, base + creg);
+ wmb();
+}
+
+static void au1000_usb_resume(unsigned long br, int creg)
+{
+ void __iomem *base = (void __iomem *)KSEG1ADDR(br);
+ __raw_writel(alchemy_usb_pmdata[0], base + creg);
+ wmb();
+}
+
+/* FIXME: write an OTG driver (or simply a stub with PM methods) to do this!! */
+static void au1200_usb_suspend(void)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1200_USB_OTG_PHYS_ADDR);
+ /* save OTG_CAP/MUX registers which indicate port<->ctrl routing */
+ alchemy_usb_pmdata[0] = __raw_readl(base + 0x00);
+ alchemy_usb_pmdata[1] = __raw_readl(base + 0x04);
+}
+
+static void au1200_usb_resume(void)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1200_USB_OTG_PHYS_ADDR);
+
+ /* need access to OTG MUX space */
+ au1200_usb_init();
+
+ /* restore OTG_CAP/MUX registers which indicate port<->ctrl routing */
+ __raw_writel(alchemy_usb_pmdata[0], base + 0x00);
+ __raw_writel(alchemy_usb_pmdata[1], base + 0x04);
+ wmb();
+}
+
+static int alchemy_usb_suspend(void)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1000:
+ case ALCHEMY_CPU_AU1500:
+ case ALCHEMY_CPU_AU1100:
+ au1000_usb_suspend(AU1000_USB_OHCI_PHYS_ADDR, AU1000_USBCFG);
+ break;
+ case ALCHEMY_CPU_AU1550:
+ au1000_usb_suspend(AU1550_USB_OHCI_PHYS_ADDR, AU1550_USBCFG);
+ break;
+ case ALCHEMY_CPU_AU1200:
+ au1200_usb_suspend();
+ break;
+ }
+ return 0;
+}
+
+static void alchemy_usb_resume(void)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1000:
+ case ALCHEMY_CPU_AU1500:
+ case ALCHEMY_CPU_AU1100:
+ au1000_usb_resume(AU1000_USB_OHCI_PHYS_ADDR, AU1000_USBCFG);
+ break;
+ case ALCHEMY_CPU_AU1550:
+ au1000_usb_resume(AU1550_USB_OHCI_PHYS_ADDR, AU1550_USBCFG);
+ break;
+ case ALCHEMY_CPU_AU1200:
+ au1200_usb_resume();
+ break;
+ }
+}
+
+static struct syscore_ops alchemy_usb_pm_ops = {
+ .suspend = alchemy_usb_suspend,
+ .resume = alchemy_usb_resume,
+};
+
+static int __init alchemy_usb_init(void)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1000:
+ case ALCHEMY_CPU_AU1500:
+ case ALCHEMY_CPU_AU1100:
+ au1000_usb_init(AU1000_USB_OHCI_PHYS_ADDR, AU1000_USBCFG);
+ break;
+ case ALCHEMY_CPU_AU1550:
+ au1000_usb_init(AU1550_USB_OHCI_PHYS_ADDR, AU1550_USBCFG);
+ break;
+ case ALCHEMY_CPU_AU1200:
+ au1200_usb_init();
+ break;
+ }
+
+ register_syscore_ops(&alchemy_usb_pm_ops);
+
+ return 0;
+}
+arch_initcall(alchemy_usb_init);
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index f260ebe..73e0d79 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -245,6 +245,15 @@ void alchemy_sleep_au1000(void);
void alchemy_sleep_au1550(void);
void au_sleep(void);
+/* USB: arch/mips/alchemy/common/usb.c */
+enum alchemy_usb_block {
+ ALCHEMY_USB_OHCI0,
+ ALCHEMY_USB_UDC0,
+ ALCHEMY_USB_EHCI0,
+ ALCHEMY_USB_OTG0,
+};
+int alchemy_usb_control(int block, int enable);
+
/* SOC Interrupt numbers */
@@ -687,7 +696,8 @@ enum soc_au1200_ints {
*/
#define AU1000_AC97_PHYS_ADDR 0x10000000 /* 012 */
-#define AU1000_USBD_PHYS_ADDR 0x10200000 /* 0123 */
+#define AU1000_USB_OHCI_PHYS_ADDR 0x10100000 /* 012 */
+#define AU1000_USB_UDC_PHYS_ADDR 0x10200000 /* 0123 */
#define AU1000_IC0_PHYS_ADDR 0x10400000 /* 01234 */
#define AU1000_MAC0_PHYS_ADDR 0x10500000 /* 023 */
#define AU1000_MAC1_PHYS_ADDR 0x10510000 /* 023 */
@@ -710,12 +720,17 @@ enum soc_au1200_ints {
#define AU1550_DBDMA_CONF_PHYS_ADDR 0x14003000 /* 34 */
#define AU1000_MACDMA0_PHYS_ADDR 0x14004000 /* 0123 */
#define AU1000_MACDMA1_PHYS_ADDR 0x14004200 /* 0123 */
+#define AU1550_USB_OHCI_PHYS_ADDR 0x14020000 /* 3 */
+#define AU1200_USB_CTL_PHYS_ADDR 0x14020000 /* 4 */
+#define AU1200_USB_OTG_PHYS_ADDR 0x14020020 /* 4 */
+#define AU1200_USB_OHCI_PHYS_ADDR 0x14020100 /* 4 */
+#define AU1200_USB_EHCI_PHYS_ADDR 0x14020200 /* 4 */
+#define AU1200_USB_UDC_PHYS_ADDR 0x14022000 /* 4 */
#ifdef CONFIG_SOC_AU1000
#define MEM_PHYS_ADDR 0x14000000
#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define USBH_PHYS_ADDR 0x10100000
#define IRDA_PHYS_ADDR 0x10300000
#define SSI0_PHYS_ADDR 0x11600000
#define SSI1_PHYS_ADDR 0x11680000
@@ -729,7 +744,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1500
#define MEM_PHYS_ADDR 0x14000000
#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define USBH_PHYS_ADDR 0x10100000
#define PCI_PHYS_ADDR 0x14005000
#define PCI_MEM_PHYS_ADDR 0x400000000ULL
#define PCI_IO_PHYS_ADDR 0x500000000ULL
@@ -745,7 +759,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1100
#define MEM_PHYS_ADDR 0x14000000
#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define USBH_PHYS_ADDR 0x10100000
#define IRDA_PHYS_ADDR 0x10300000
#define SSI0_PHYS_ADDR 0x11600000
#define SSI1_PHYS_ADDR 0x11680000
@@ -760,7 +773,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1550
#define MEM_PHYS_ADDR 0x14000000
#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define USBH_PHYS_ADDR 0x14020000
#define PCI_PHYS_ADDR 0x14005000
#define PE_PHYS_ADDR 0x14008000
#define PSC0_PHYS_ADDR 0x11A00000
@@ -783,8 +795,6 @@ enum soc_au1200_ints {
#define STATIC_MEM_PHYS_ADDR 0x14001000
#define AES_PHYS_ADDR 0x10300000
#define CIM_PHYS_ADDR 0x14004000
-#define USBM_PHYS_ADDR 0x14020000
-#define USBH_PHYS_ADDR 0x14020100
#define PSC0_PHYS_ADDR 0x11A00000
#define PSC1_PHYS_ADDR 0x11B00000
#define LCD_PHYS_ADDR 0x15000000
@@ -868,21 +878,6 @@ enum soc_au1200_ints {
#define USB_EHCI_LEN 0x100
#define USB_UDC_BASE 0x14022000
#define USB_UDC_LEN 0x2000
-#define USB_MSR_BASE 0xB4020000
-#define USB_MSR_MCFG 4
-#define USBMSRMCFG_OMEMEN 0
-#define USBMSRMCFG_OBMEN 1
-#define USBMSRMCFG_EMEMEN 2
-#define USBMSRMCFG_EBMEN 3
-#define USBMSRMCFG_DMEMEN 4
-#define USBMSRMCFG_DBMEN 5
-#define USBMSRMCFG_GMEMEN 6
-#define USBMSRMCFG_OHCCLKEN 16
-#define USBMSRMCFG_EHCCLKEN 17
-#define USBMSRMCFG_UDCCLKEN 18
-#define USBMSRMCFG_PHYPLLEN 19
-#define USBMSRMCFG_RDCOMB 30
-#define USBMSRMCFG_PFEN 31
#define FOR_PLATFORM_C_USB_HOST_INT AU1200_USB_INT
@@ -963,51 +958,6 @@ enum soc_au1200_ints {
#define USB_OHCI_LEN 0x00100000
#endif
-#ifndef CONFIG_SOC_AU1200
-
-/* USB Device Controller */
-#define USBD_EP0RD 0xB0200000
-#define USBD_EP0WR 0xB0200004
-#define USBD_EP2WR 0xB0200008
-#define USBD_EP3WR 0xB020000C
-#define USBD_EP4RD 0xB0200010
-#define USBD_EP5RD 0xB0200014
-#define USBD_INTEN 0xB0200018
-#define USBD_INTSTAT 0xB020001C
-# define USBDEV_INT_SOF (1 << 12)
-# define USBDEV_INT_HF_BIT 6
-# define USBDEV_INT_HF_MASK (0x3f << USBDEV_INT_HF_BIT)
-# define USBDEV_INT_CMPLT_BIT 0
-# define USBDEV_INT_CMPLT_MASK (0x3f << USBDEV_INT_CMPLT_BIT)
-#define USBD_CONFIG 0xB0200020
-#define USBD_EP0CS 0xB0200024
-#define USBD_EP2CS 0xB0200028
-#define USBD_EP3CS 0xB020002C
-#define USBD_EP4CS 0xB0200030
-#define USBD_EP5CS 0xB0200034
-# define USBDEV_CS_SU (1 << 14)
-# define USBDEV_CS_NAK (1 << 13)
-# define USBDEV_CS_ACK (1 << 12)
-# define USBDEV_CS_BUSY (1 << 11)
-# define USBDEV_CS_TSIZE_BIT 1
-# define USBDEV_CS_TSIZE_MASK (0x3ff << USBDEV_CS_TSIZE_BIT)
-# define USBDEV_CS_STALL (1 << 0)
-#define USBD_EP0RDSTAT 0xB0200040
-#define USBD_EP0WRSTAT 0xB0200044
-#define USBD_EP2WRSTAT 0xB0200048
-#define USBD_EP3WRSTAT 0xB020004C
-#define USBD_EP4RDSTAT 0xB0200050
-#define USBD_EP5RDSTAT 0xB0200054
-# define USBDEV_FSTAT_FLUSH (1 << 6)
-# define USBDEV_FSTAT_UF (1 << 5)
-# define USBDEV_FSTAT_OF (1 << 4)
-# define USBDEV_FSTAT_FCNT_BIT 0
-# define USBDEV_FSTAT_FCNT_MASK (0x0f << USBDEV_FSTAT_FCNT_BIT)
-#define USBD_ENABLE 0xB0200058
-# define USBDEV_ENABLE (1 << 1)
-# define USBDEV_CE (1 << 0)
-
-#endif /* !CONFIG_SOC_AU1200 */
/* Ethernet Controllers */
diff --git a/drivers/usb/host/ehci-au1xxx.c b/drivers/usb/host/ehci-au1xxx.c
index 42ae574..e480dc1 100644
--- a/drivers/usb/host/ehci-au1xxx.c
+++ b/drivers/usb/host/ehci-au1xxx.c
@@ -14,61 +14,9 @@
#include <linux/platform_device.h>
#include <asm/mach-au1x00/au1000.h>
-#define USB_HOST_CONFIG (USB_MSR_BASE + USB_MSR_MCFG)
-#define USB_MCFG_PFEN (1<<31)
-#define USB_MCFG_RDCOMB (1<<30)
-#define USB_MCFG_SSDEN (1<<23)
-#define USB_MCFG_PHYPLLEN (1<<19)
-#define USB_MCFG_UCECLKEN (1<<18)
-#define USB_MCFG_EHCCLKEN (1<<17)
-#ifdef CONFIG_DMA_COHERENT
-#define USB_MCFG_UCAM (1<<7)
-#else
-#define USB_MCFG_UCAM (0)
-#endif
-#define USB_MCFG_EBMEN (1<<3)
-#define USB_MCFG_EMEMEN (1<<2)
-
-#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN)
-#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \
- USBH_ENABLE_CE | USB_MCFG_SSDEN | \
- USB_MCFG_UCAM | USB_MCFG_EBMEN | \
- USB_MCFG_EMEMEN)
-
-#define USBH_DISABLE (USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
extern int usb_disabled(void);
-static void au1xxx_start_ehc(void)
-{
- /* enable clock to EHCI block and HS PHY PLL*/
- au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-
- /* enable EHCI mmio */
- au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-}
-
-static void au1xxx_stop_ehc(void)
-{
- unsigned long c;
-
- /* Disable mem */
- au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-
- /* Disable EHC clock. If the HS PHY is unused disable it too. */
- c = au_readl(USB_HOST_CONFIG) & ~USB_MCFG_EHCCLKEN;
- if (!(c & USB_MCFG_UCECLKEN)) /* UDC disabled? */
- c &= ~USB_MCFG_PHYPLLEN; /* yes: disable HS PHY PLL */
- au_writel(c, USB_HOST_CONFIG);
- au_sync();
-}
-
static int au1xxx_ehci_setup(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
@@ -136,16 +84,6 @@ static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
if (usb_disabled())
return -ENODEV;
-#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
- /* Au1200 AB USB does not support coherent memory */
- if (!(read_c0_prid() & 0xff)) {
- printk(KERN_INFO "%s: this is chip revision AB!\n", pdev->name);
- printk(KERN_INFO "%s: update your board or re-configure"
- " the kernel\n", pdev->name);
- return -ENODEV;
- }
-#endif
-
if (pdev->resource[1].flags != IORESOURCE_IRQ) {
pr_debug("resource[1] is not IORESOURCE_IRQ");
return -ENOMEM;
@@ -171,7 +109,11 @@ static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
goto err2;
}
- au1xxx_start_ehc();
+ if (alchemy_usb_control(ALCHEMY_USB_EHCI0, 1)) {
+ printk(KERN_INFO "%s: controller init failed!\n", pdev->name);
+ ret = -ENODEV;
+ goto err3;
+ }
ehci = hcd_to_ehci(hcd);
ehci->caps = hcd->regs;
@@ -187,7 +129,8 @@ static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
return ret;
}
- au1xxx_stop_ehc();
+ alchemy_usb_control(ALCHEMY_USB_EHCI0, 0);
+err3:
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
@@ -201,10 +144,10 @@ static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
struct usb_hcd *hcd = platform_get_drvdata(pdev);
usb_remove_hcd(hcd);
+ alchemy_usb_control(ALCHEMY_USB_EHCI0, 0);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
- au1xxx_stop_ehc();
platform_set_drvdata(pdev, NULL);
return 0;
@@ -236,7 +179,7 @@ static int ehci_hcd_au1xxx_drv_suspend(struct device *dev)
// could save FLADJ in case of Vaux power loss
// ... we'd only use it to handle clock skew
- au1xxx_stop_ehc();
+ alchemy_usb_control(ALCHEMY_USB_EHCI0, 0);
return rc;
}
@@ -246,7 +189,7 @@ static int ehci_hcd_au1xxx_drv_resume(struct device *dev)
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
- au1xxx_start_ehc();
+ alchemy_usb_control(ALCHEMY_USB_EHCI0, 1);
// maybe restore FLADJ
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index 958d985..299d719 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -23,92 +23,9 @@
#include <asm/mach-au1x00/au1000.h>
-#ifndef CONFIG_SOC_AU1200
-
-#define USBH_ENABLE_BE (1<<0)
-#define USBH_ENABLE_C (1<<1)
-#define USBH_ENABLE_E (1<<2)
-#define USBH_ENABLE_CE (1<<3)
-#define USBH_ENABLE_RD (1<<4)
-
-#ifdef __LITTLE_ENDIAN
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C)
-#elif defined(__BIG_ENDIAN)
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | \
- USBH_ENABLE_BE)
-#else
-#error not byte order defined
-#endif
-
-#else /* Au1200 */
-
-#define USB_HOST_CONFIG (USB_MSR_BASE + USB_MSR_MCFG)
-#define USB_MCFG_PFEN (1<<31)
-#define USB_MCFG_RDCOMB (1<<30)
-#define USB_MCFG_SSDEN (1<<23)
-#define USB_MCFG_OHCCLKEN (1<<16)
-#ifdef CONFIG_DMA_COHERENT
-#define USB_MCFG_UCAM (1<<7)
-#else
-#define USB_MCFG_UCAM (0)
-#endif
-#define USB_MCFG_OBMEN (1<<1)
-#define USB_MCFG_OMEMEN (1<<0)
-
-#define USBH_ENABLE_CE USB_MCFG_OHCCLKEN
-
-#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \
- USBH_ENABLE_CE | USB_MCFG_SSDEN | \
- USB_MCFG_UCAM | \
- USB_MCFG_OBMEN | USB_MCFG_OMEMEN)
-
-#define USBH_DISABLE (USB_MCFG_OBMEN | USB_MCFG_OMEMEN)
-
-#endif /* Au1200 */
extern int usb_disabled(void);
-static void au1xxx_start_ohc(void)
-{
- /* enable host controller */
-#ifndef CONFIG_SOC_AU1200
- au_writel(USBH_ENABLE_CE, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-
- au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-
- /* wait for reset complete (read register twice; see au1500 errata) */
- while (au_readl(USB_HOST_CONFIG),
- !(au_readl(USB_HOST_CONFIG) & USBH_ENABLE_RD))
- udelay(1000);
-
-#else /* Au1200 */
- au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-
- au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
- au_sync();
- udelay(2000);
-#endif /* Au1200 */
-}
-
-static void au1xxx_stop_ohc(void)
-{
-#ifdef CONFIG_SOC_AU1200
- /* Disable mem */
- au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG);
- au_sync();
- udelay(1000);
-#endif
- /* Disable clock */
- au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
- au_sync();
-}
-
static int __devinit ohci_au1xxx_start(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
@@ -178,17 +95,6 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
if (usb_disabled())
return -ENODEV;
-#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
- /* Au1200 AB USB does not support coherent memory */
- if (!(read_c0_prid() & 0xff)) {
- printk(KERN_INFO "%s: this is chip revision AB !!\n",
- pdev->name);
- printk(KERN_INFO "%s: update your board or re-configure "
- "the kernel\n", pdev->name);
- return -ENODEV;
- }
-#endif
-
if (pdev->resource[1].flags != IORESOURCE_IRQ) {
pr_debug("resource[1] is not IORESOURCE_IRQ\n");
return -ENOMEM;
@@ -214,7 +120,12 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
goto err2;
}
- au1xxx_start_ohc();
+ if (alchemy_usb_control(ALCHEMY_USB_OHCI0, 1)) {
+ printk(KERN_INFO "%s: controller init failed!\n", pdev->name);
+ ret = -ENODEV;
+ goto err3;
+ }
+
ohci_hcd_init(hcd_to_ohci(hcd));
ret = usb_add_hcd(hcd, pdev->resource[1].start,
@@ -224,7 +135,8 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
return ret;
}
- au1xxx_stop_ohc();
+ alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
+err3:
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
@@ -238,7 +150,7 @@ static int ohci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
struct usb_hcd *hcd = platform_get_drvdata(pdev);
usb_remove_hcd(hcd);
- au1xxx_stop_ohc();
+ alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
@@ -275,7 +187,7 @@ static int ohci_hcd_au1xxx_drv_suspend(struct device *dev)
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
- au1xxx_stop_ohc();
+ alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
bail:
spin_unlock_irqrestore(&ohci->lock, flags);
@@ -286,7 +198,7 @@ static int ohci_hcd_au1xxx_drv_resume(struct device *dev)
{
struct usb_hcd *hcd = dev_get_drvdata(dev);
- au1xxx_start_ohc();
+ alchemy_usb_control(ALCHEMY_USB_OHCI0, 1);
set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
ohci_finish_controller_resume(hcd);
--
1.7.5.rc3
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 2/3] MIPS: Alchemy: rewrite USB platform setup.
2011-05-24 8:01 [PATCH 0/3] MIPS: Alchemy: USB updates and more cleanups Manuel Lauss
2011-05-24 8:01 ` [PATCH 1/3] MIPS: Alchemy: abstract USB block control register access Manuel Lauss
@ 2011-05-24 8:01 ` Manuel Lauss
2011-05-24 8:01 ` [PATCH 3/3] MIPS: Alchemy: more base address cleanup Manuel Lauss
2 siblings, 0 replies; 4+ messages in thread
From: Manuel Lauss @ 2011-05-24 8:01 UTC (permalink / raw)
To: Ralf Baechle; +Cc: Linux-MIPS, Manuel Lauss
Use runtime CPU detection to setup all USB parts.
Remove the Au1200 OTG and UDC platform devices since there are no
drivers for them anyway.
Clean up the USB address mess in the au1000 header.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/common/platform.c | 183 +++++++++++----------------
arch/mips/include/asm/mach-au1x00/au1000.h | 55 ---------
2 files changed, 75 insertions(+), 163 deletions(-)
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 7400c93..e92a464 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -111,34 +111,84 @@ static void __init alchemy_setup_uarts(int ctype)
printk(KERN_INFO "Alchemy: failed to register UARTs\n");
}
-/* OHCI (USB full speed host controller) */
-static struct resource au1xxx_usb_ohci_resources[] = {
- [0] = {
- .start = USB_OHCI_BASE,
- .end = USB_OHCI_BASE + USB_OHCI_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = FOR_PLATFORM_C_USB_HOST_INT,
- .end = FOR_PLATFORM_C_USB_HOST_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
+/* The dmamask must be set for OHCI/EHCI to work */
+static u64 alchemy_ohci_dmamask = DMA_BIT_MASK(32);
+static u64 __maybe_unused alchemy_ehci_dmamask = DMA_BIT_MASK(32);
-static struct platform_device au1xxx_usb_ohci_device = {
- .name = "au1xxx-ohci",
- .id = 0,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1xxx_usb_ohci_resources),
- .resource = au1xxx_usb_ohci_resources,
+static unsigned long alchemy_ohci_data[][2] __initdata = {
+ [ALCHEMY_CPU_AU1000] = { AU1000_USB_OHCI_PHYS_ADDR, AU1000_USB_HOST_INT },
+ [ALCHEMY_CPU_AU1500] = { AU1000_USB_OHCI_PHYS_ADDR, AU1500_USB_HOST_INT },
+ [ALCHEMY_CPU_AU1100] = { AU1000_USB_OHCI_PHYS_ADDR, AU1100_USB_HOST_INT },
+ [ALCHEMY_CPU_AU1550] = { AU1550_USB_OHCI_PHYS_ADDR, AU1550_USB_HOST_INT },
+ [ALCHEMY_CPU_AU1200] = { AU1200_USB_OHCI_PHYS_ADDR, AU1200_USB_INT },
+};
+
+static unsigned long alchemy_ehci_data[][2] __initdata = {
+ [ALCHEMY_CPU_AU1200] = { AU1200_USB_EHCI_PHYS_ADDR, AU1200_USB_INT },
};
+static int __init _new_usbres(struct resource **r, struct platform_device **d)
+{
+ *r = kzalloc(sizeof(struct resource) * 2, GFP_KERNEL);
+ if (!*r)
+ return -ENOMEM;
+ *d = kzalloc(sizeof(struct platform_device), GFP_KERNEL);
+ if (!*d) {
+ kfree(*r);
+ return -ENOMEM;
+ }
+
+ (*d)->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+ (*d)->num_resources = 2;
+ (*d)->resource = *r;
+
+ return 0;
+}
+
+static void __init alchemy_setup_usb(int ctype)
+{
+ struct resource *res;
+ struct platform_device *pdev;
+
+ /* setup OHCI0. Every variant has one */
+ if (_new_usbres(&res, &pdev))
+ return;
+
+ res[0].start = alchemy_ohci_data[ctype][0];
+ res[0].end = res[0].start + 0x100 - 1;
+ res[0].flags = IORESOURCE_MEM;
+ res[1].start = alchemy_ohci_data[ctype][1];
+ res[1].end = res[1].start;
+ res[1].flags = IORESOURCE_IRQ;
+ pdev->name = "au1xxx-ohci";
+ pdev->id = 0;
+ pdev->dev.dma_mask = &alchemy_ohci_dmamask;
+
+ if (platform_device_register(pdev))
+ printk(KERN_INFO "Alchemy USB: cannot add OHCI0\n");
+
+
+ /* setup EHCI0: Au1200 */
+ if (ctype == ALCHEMY_CPU_AU1200) {
+ if (_new_usbres(&res, &pdev))
+ return;
+
+ res[0].start = alchemy_ehci_data[ctype][0];
+ res[0].end = res[0].start + 0x100 - 1;
+ res[0].flags = IORESOURCE_MEM;
+ res[1].start = alchemy_ehci_data[ctype][1];
+ res[1].end = res[1].start;
+ res[1].flags = IORESOURCE_IRQ;
+ pdev->name = "au1xxx-ehci";
+ pdev->id = 0;
+ pdev->dev.dma_mask = &alchemy_ehci_dmamask;
+
+ if (platform_device_register(pdev))
+ printk(KERN_INFO "Alchemy USB: cannot add EHCI0\n");
+ }
+}
+
/*** AU1100 LCD controller ***/
#ifdef CONFIG_FB_AU1100
@@ -170,86 +220,6 @@ static struct platform_device au1100_lcd_device = {
#endif
#ifdef CONFIG_SOC_AU1200
-/* EHCI (USB high speed host controller) */
-static struct resource au1xxx_usb_ehci_resources[] = {
- [0] = {
- .start = USB_EHCI_BASE,
- .end = USB_EHCI_BASE + USB_EHCI_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_USB_INT,
- .end = AU1200_USB_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 ehci_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1xxx_usb_ehci_device = {
- .name = "au1xxx-ehci",
- .id = 0,
- .dev = {
- .dma_mask = &ehci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1xxx_usb_ehci_resources),
- .resource = au1xxx_usb_ehci_resources,
-};
-
-/* Au1200 UDC (USB gadget controller) */
-static struct resource au1xxx_usb_gdt_resources[] = {
- [0] = {
- .start = USB_UDC_BASE,
- .end = USB_UDC_BASE + USB_UDC_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_USB_INT,
- .end = AU1200_USB_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 udc_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1xxx_usb_gdt_device = {
- .name = "au1xxx-udc",
- .id = 0,
- .dev = {
- .dma_mask = &udc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1xxx_usb_gdt_resources),
- .resource = au1xxx_usb_gdt_resources,
-};
-
-/* Au1200 UOC (USB OTG controller) */
-static struct resource au1xxx_usb_otg_resources[] = {
- [0] = {
- .start = USB_UOC_BASE,
- .end = USB_UOC_BASE + USB_UOC_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_USB_INT,
- .end = AU1200_USB_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 uoc_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1xxx_usb_otg_device = {
- .name = "au1xxx-uoc",
- .id = 0,
- .dev = {
- .dma_mask = &uoc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1xxx_usb_otg_resources),
- .resource = au1xxx_usb_otg_resources,
-};
static struct resource au1200_lcd_resources[] = {
[0] = {
@@ -534,14 +504,10 @@ static void __init alchemy_setup_macs(int ctype)
}
static struct platform_device *au1xxx_platform_devices[] __initdata = {
- &au1xxx_usb_ohci_device,
#ifdef CONFIG_FB_AU1100
&au1100_lcd_device,
#endif
#ifdef CONFIG_SOC_AU1200
- &au1xxx_usb_ehci_device,
- &au1xxx_usb_gdt_device,
- &au1xxx_usb_otg_device,
&au1200_lcd_device,
&au1200_mmc0_device,
#ifndef CONFIG_MIPS_DB1200
@@ -559,6 +525,7 @@ static int __init au1xxx_platform_init(void)
alchemy_setup_uarts(ctype);
alchemy_setup_macs(ctype);
+ alchemy_setup_usb(ctype);
err = platform_add_devices(au1xxx_platform_devices,
ARRAY_SIZE(au1xxx_platform_devices));
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index 73e0d79..86d39c3 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -833,56 +833,6 @@ enum soc_au1200_ints {
#endif
-
-
-/* Au1000 */
-#ifdef CONFIG_SOC_AU1000
-
-#define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */
-#define USB_HOST_CONFIG 0xB017FFFC
-#define FOR_PLATFORM_C_USB_HOST_INT AU1000_USB_HOST_INT
-#endif /* CONFIG_SOC_AU1000 */
-
-/* Au1500 */
-#ifdef CONFIG_SOC_AU1500
-
-#define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */
-#define USB_HOST_CONFIG 0xB017fffc
-#define FOR_PLATFORM_C_USB_HOST_INT AU1500_USB_HOST_INT
-#endif /* CONFIG_SOC_AU1500 */
-
-/* Au1100 */
-#ifdef CONFIG_SOC_AU1100
-
-#define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */
-#define USB_HOST_CONFIG 0xB017FFFC
-#define FOR_PLATFORM_C_USB_HOST_INT AU1100_USB_HOST_INT
-#endif /* CONFIG_SOC_AU1100 */
-
-#ifdef CONFIG_SOC_AU1550
-
-#define USB_OHCI_BASE 0x14020000 /* phys addr for ioremap */
-#define USB_OHCI_LEN 0x00060000
-#define USB_HOST_CONFIG 0xB4027ffc
-#define FOR_PLATFORM_C_USB_HOST_INT AU1550_USB_HOST_INT
-#endif /* CONFIG_SOC_AU1550 */
-
-
-#ifdef CONFIG_SOC_AU1200
-
-#define USB_UOC_BASE 0x14020020
-#define USB_UOC_LEN 0x20
-#define USB_OHCI_BASE 0x14020100
-#define USB_OHCI_LEN 0x100
-#define USB_EHCI_BASE 0x14020200
-#define USB_EHCI_LEN 0x100
-#define USB_UDC_BASE 0x14022000
-#define USB_UDC_LEN 0x2000
-
-#define FOR_PLATFORM_C_USB_HOST_INT AU1200_USB_INT
-
-#endif /* CONFIG_SOC_AU1200 */
-
/* Programmable Counters 0 and 1 */
#define SYS_BASE 0xB1900000
#define SYS_COUNTER_CNTRL (SYS_BASE + 0x14)
@@ -953,11 +903,6 @@ enum soc_au1200_ints {
# define I2S_CONTROL_D (1 << 1)
# define I2S_CONTROL_CE (1 << 0)
-/* USB Host Controller */
-#ifndef USB_OHCI_LEN
-#define USB_OHCI_LEN 0x00100000
-#endif
-
/* Ethernet Controllers */
--
1.7.5.rc3
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 3/3] MIPS: Alchemy: more base address cleanup
2011-05-24 8:01 [PATCH 0/3] MIPS: Alchemy: USB updates and more cleanups Manuel Lauss
2011-05-24 8:01 ` [PATCH 1/3] MIPS: Alchemy: abstract USB block control register access Manuel Lauss
2011-05-24 8:01 ` [PATCH 2/3] MIPS: Alchemy: rewrite USB platform setup Manuel Lauss
@ 2011-05-24 8:01 ` Manuel Lauss
2 siblings, 0 replies; 4+ messages in thread
From: Manuel Lauss @ 2011-05-24 8:01 UTC (permalink / raw)
To: Ralf Baechle; +Cc: Linux-MIPS, Manuel Lauss
remove all redundant peripheral base address defines, fix
all affected boards and drivers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/common/platform.c | 12 ++--
arch/mips/alchemy/devboards/db1200/platform.c | 52 ++++++-------
arch/mips/alchemy/devboards/db1x00/platform.c | 40 ++++-----
arch/mips/alchemy/devboards/pb1100/platform.c | 20 ++---
arch/mips/alchemy/devboards/pb1200/platform.c | 42 +++++-----
arch/mips/alchemy/devboards/pb1500/platform.c | 22 +++---
arch/mips/alchemy/devboards/pb1550/platform.c | 40 ++++-----
arch/mips/alchemy/xxs1500/platform.c | 12 ++--
arch/mips/include/asm/mach-au1x00/au1000.h | 103 ++++++------------------
arch/mips/include/asm/mach-au1x00/au1xxx_psc.h | 26 ------
arch/mips/include/asm/mach-db1x00/db1x00.h | 8 +-
arch/mips/include/asm/mach-pb1x00/pb1200.h | 8 +-
arch/mips/include/asm/mach-pb1x00/pb1550.h | 8 +-
13 files changed, 146 insertions(+), 247 deletions(-)
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index e92a464..a5b37b3 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -194,8 +194,8 @@ static void __init alchemy_setup_usb(int ctype)
#ifdef CONFIG_FB_AU1100
static struct resource au1100_lcd_resources[] = {
[0] = {
- .start = LCD_PHYS_ADDR,
- .end = LCD_PHYS_ADDR + 0x800 - 1,
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
@@ -223,8 +223,8 @@ static struct platform_device au1100_lcd_device = {
static struct resource au1200_lcd_resources[] = {
[0] = {
- .start = LCD_PHYS_ADDR,
- .end = LCD_PHYS_ADDR + 0x800 - 1,
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
@@ -328,8 +328,8 @@ static struct platform_device au1200_mmc1_device = {
#ifdef SMBUS_PSC_BASE
static struct resource pbdb_smbus_resources[] = {
{
- .start = CPHYSADDR(SMBUS_PSC_BASE),
- .end = CPHYSADDR(SMBUS_PSC_BASE + 0xfffff),
+ .start = SMBUS_PSC_BASE,
+ .end = SMBUS_PSC_BASE + 0xfff,
.flags = IORESOURCE_MEM,
},
};
diff --git a/arch/mips/alchemy/devboards/db1200/platform.c b/arch/mips/alchemy/devboards/db1200/platform.c
index fbb5593..95c7327 100644
--- a/arch/mips/alchemy/devboards/db1200/platform.c
+++ b/arch/mips/alchemy/devboards/db1200/platform.c
@@ -343,8 +343,8 @@ struct au1xmmc_platform_data au1xmmc_platdata[] = {
static struct resource au1200_psc0_res[] = {
[0] = {
- .start = PSC0_PHYS_ADDR,
- .end = PSC0_PHYS_ADDR + 0x000fffff,
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
[1] = {
@@ -401,8 +401,8 @@ static struct platform_device db1200_spi_dev = {
static struct resource au1200_psc1_res[] = {
[0] = {
- .start = PSC1_PHYS_ADDR,
- .end = PSC1_PHYS_ADDR + 0x000fffff,
+ .start = AU1550_PSC1_PHYS_ADDR,
+ .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
[1] = {
@@ -510,32 +510,28 @@ static int __init db1200_dev_init(void)
/* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
__raw_writel(PSC_SEL_CLK_SERCLK,
- (void __iomem *)KSEG1ADDR(PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
- PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_MEM_PHYS_ADDR,
- PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_IO_PHYS_ADDR,
- PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1200_PC0_INT,
- DB1200_PC0_INSERT_INT,
- /*DB1200_PC0_STSCHG_INT*/0,
- DB1200_PC0_EJECT_INT,
- 0);
-
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- PCMCIA_IO_PHYS_ADDR + 0x004000000,
- PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1200_PC1_INT,
- DB1200_PC1_INSERT_INT,
- /*DB1200_PC1_STSCHG_INT*/0,
- DB1200_PC1_EJECT_INT,
- 1);
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
+ /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
+ /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
db1x_register_norflash(64 << 20, 2, swapped);
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
index 978d5ab..ef8017f 100644
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ b/arch/mips/alchemy/devboards/db1x00/platform.c
@@ -88,29 +88,25 @@
static int __init db1xxx_dev_init(void)
{
#ifdef DB1XXX_HAS_PCMCIA
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
- PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_MEM_PHYS_ADDR,
- PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_IO_PHYS_ADDR,
- PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1XXX_PCMCIA_CARD0,
- DB1XXX_PCMCIA_CD0,
- /*DB1XXX_PCMCIA_STSCHG0*/0,
- 0,
- 0);
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
+ /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- PCMCIA_IO_PHYS_ADDR + 0x004000000,
- PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1XXX_PCMCIA_CARD1,
- DB1XXX_PCMCIA_CD1,
- /*DB1XXX_PCMCIA_STSCHG1*/0,
- 0,
- 1);
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
+ /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
#endif
db1x_register_norflash(BOARD_FLASH_SIZE, BOARD_FLASH_WIDTH, F_SWAPPED);
return 0;
diff --git a/arch/mips/alchemy/devboards/pb1100/platform.c b/arch/mips/alchemy/devboards/pb1100/platform.c
index 2c8dc29..8a4e733 100644
--- a/arch/mips/alchemy/devboards/pb1100/platform.c
+++ b/arch/mips/alchemy/devboards/pb1100/platform.c
@@ -30,17 +30,15 @@ static int __init pb1100_dev_init(void)
int swapped;
/* PCMCIA. single socket, identical to Pb1500 */
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
- PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_MEM_PHYS_ADDR,
- PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_IO_PHYS_ADDR,
- PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1100_GPIO11_INT, /* card */
- AU1100_GPIO9_INT, /* insert */
- /*AU1100_GPIO10_INT*/0, /* stschg */
- 0, /* eject */
- 0); /* id */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
+ /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
diff --git a/arch/mips/alchemy/devboards/pb1200/platform.c b/arch/mips/alchemy/devboards/pb1200/platform.c
index 3ef2dce..c52809d 100644
--- a/arch/mips/alchemy/devboards/pb1200/platform.c
+++ b/arch/mips/alchemy/devboards/pb1200/platform.c
@@ -170,29 +170,25 @@ static int __init board_register_devices(void)
{
int swapped;
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
- PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_MEM_PHYS_ADDR,
- PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_IO_PHYS_ADDR,
- PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- PB1200_PC0_INT,
- PB1200_PC0_INSERT_INT,
- /*PB1200_PC0_STSCHG_INT*/0,
- PB1200_PC0_EJECT_INT,
- 0);
-
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- PCMCIA_IO_PHYS_ADDR + 0x008000000,
- PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- PB1200_PC1_INT,
- PB1200_PC1_INSERT_INT,
- /*PB1200_PC1_STSCHG_INT*/0,
- PB1200_PC1_EJECT_INT,
- 1);
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
+ /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
+ /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
index d443bc7..42b0e6b 100644
--- a/arch/mips/alchemy/devboards/pb1500/platform.c
+++ b/arch/mips/alchemy/devboards/pb1500/platform.c
@@ -28,18 +28,16 @@ static int __init pb1500_dev_init(void)
{
int swapped;
- /* PCMCIA. single socket, identical to Pb1500 */
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
- PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_MEM_PHYS_ADDR,
- PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_IO_PHYS_ADDR,
- PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1500_GPIO11_INT, /* card */
- AU1500_GPIO9_INT, /* insert */
- /*AU1500_GPIO10_INT*/0, /* stschg */
- 0, /* eject */
- 0); /* id */
+ /* PCMCIA. single socket, identical to Pb1100 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
+ /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
index d7150d0..87c79b7 100644
--- a/arch/mips/alchemy/devboards/pb1550/platform.c
+++ b/arch/mips/alchemy/devboards/pb1550/platform.c
@@ -37,29 +37,23 @@ static int __init pb1550_dev_init(void)
* drivers are used to shared irqs and b) statuschange isn't really use-
* ful anyway.
*/
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
- PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_MEM_PHYS_ADDR,
- PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- PCMCIA_IO_PHYS_ADDR,
- PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1550_GPIO201_205_INT,
- AU1550_GPIO0_INT,
- 0,
- 0,
- 0);
-
- db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- PCMCIA_IO_PHYS_ADDR + 0x008000000,
- PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- AU1550_GPIO201_205_INT,
- AU1550_GPIO1_INT,
- 0,
- 0,
- 1);
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
diff --git a/arch/mips/alchemy/xxs1500/platform.c b/arch/mips/alchemy/xxs1500/platform.c
index e87c45c..06a3a45 100644
--- a/arch/mips/alchemy/xxs1500/platform.c
+++ b/arch/mips/alchemy/xxs1500/platform.c
@@ -27,20 +27,20 @@ static struct resource xxs1500_pcmcia_res[] = {
{
.name = "pcmcia-io",
.flags = IORESOURCE_MEM,
- .start = PCMCIA_IO_PHYS_ADDR,
- .end = PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
+ .start = AU1000_PCMCIA_IO_PHYS_ADDR,
+ .end = AU1000_PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
},
{
.name = "pcmcia-attr",
.flags = IORESOURCE_MEM,
- .start = PCMCIA_ATTR_PHYS_ADDR,
- .end = PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ .start = AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ .end = AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
},
{
.name = "pcmcia-mem",
.flags = IORESOURCE_MEM,
- .start = PCMCIA_MEM_PHYS_ADDR,
- .end = PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ .start = AU1000_PCMCIA_MEM_PHYS_ADDR,
+ .end = AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
},
};
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index 86d39c3..bcf3d1e 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -698,114 +698,61 @@ enum soc_au1200_ints {
#define AU1000_AC97_PHYS_ADDR 0x10000000 /* 012 */
#define AU1000_USB_OHCI_PHYS_ADDR 0x10100000 /* 012 */
#define AU1000_USB_UDC_PHYS_ADDR 0x10200000 /* 0123 */
+#define AU1000_IRDA_PHYS_ADDR 0x10300000 /* 02 */
+#define AU1200_AES_PHYS_ADDR 0x10300000 /* 4 */
#define AU1000_IC0_PHYS_ADDR 0x10400000 /* 01234 */
#define AU1000_MAC0_PHYS_ADDR 0x10500000 /* 023 */
#define AU1000_MAC1_PHYS_ADDR 0x10510000 /* 023 */
#define AU1000_MACEN_PHYS_ADDR 0x10520000 /* 023 */
#define AU1100_SD0_PHYS_ADDR 0x10600000 /* 24 */
#define AU1100_SD1_PHYS_ADDR 0x10680000 /* 24 */
+#define AU1550_PSC2_PHYS_ADDR 0x10A00000 /* 3 */
+#define AU1550_PSC3_PHYS_ADDR 0x10B00000 /* 3 */
#define AU1000_I2S_PHYS_ADDR 0x11000000 /* 02 */
#define AU1500_MAC0_PHYS_ADDR 0x11500000 /* 1 */
#define AU1500_MAC1_PHYS_ADDR 0x11510000 /* 1 */
#define AU1500_MACEN_PHYS_ADDR 0x11520000 /* 1 */
#define AU1000_UART0_PHYS_ADDR 0x11100000 /* 01234 */
+#define AU1200_SWCNT_PHYS_ADDR 0x1110010C /* 4 */
#define AU1000_UART1_PHYS_ADDR 0x11200000 /* 0234 */
#define AU1000_UART2_PHYS_ADDR 0x11300000 /* 0 */
#define AU1000_UART3_PHYS_ADDR 0x11400000 /* 0123 */
+#define AU1000_SSI0_PHYS_ADDR 0x11600000 /* 02 */
+#define AU1000_SSI1_PHYS_ADDR 0x11680000 /* 02 */
#define AU1500_GPIO2_PHYS_ADDR 0x11700000 /* 1234 */
#define AU1000_IC1_PHYS_ADDR 0x11800000 /* 01234 */
#define AU1000_SYS_PHYS_ADDR 0x11900000 /* 01234 */
+#define AU1550_PSC0_PHYS_ADDR 0x11A00000 /* 34 */
+#define AU1550_PSC1_PHYS_ADDR 0x11B00000 /* 34 */
+#define AU1000_MEM_PHYS_ADDR 0x14000000 /* 01234 */
+#define AU1000_STATIC_MEM_PHYS_ADDR 0x14001000 /* 01234 */
#define AU1000_DMA_PHYS_ADDR 0x14002000 /* 012 */
#define AU1550_DBDMA_PHYS_ADDR 0x14002000 /* 34 */
#define AU1550_DBDMA_CONF_PHYS_ADDR 0x14003000 /* 34 */
#define AU1000_MACDMA0_PHYS_ADDR 0x14004000 /* 0123 */
#define AU1000_MACDMA1_PHYS_ADDR 0x14004200 /* 0123 */
+#define AU1200_CIM_PHYS_ADDR 0x14004000 /* 4 */
+#define AU1500_PCI_PHYS_ADDR 0x14005000 /* 13 */
+#define AU1550_PE_PHYS_ADDR 0x14008000 /* 3 */
+#define AU1200_MAEBE_PHYS_ADDR 0x14010000 /* 4 */
+#define AU1200_MAEFE_PHYS_ADDR 0x14012000 /* 4 */
#define AU1550_USB_OHCI_PHYS_ADDR 0x14020000 /* 3 */
#define AU1200_USB_CTL_PHYS_ADDR 0x14020000 /* 4 */
#define AU1200_USB_OTG_PHYS_ADDR 0x14020020 /* 4 */
#define AU1200_USB_OHCI_PHYS_ADDR 0x14020100 /* 4 */
#define AU1200_USB_EHCI_PHYS_ADDR 0x14020200 /* 4 */
#define AU1200_USB_UDC_PHYS_ADDR 0x14022000 /* 4 */
+#define AU1100_LCD_PHYS_ADDR 0x15000000 /* 2 */
+#define AU1200_LCD_PHYS_ADDR 0x15000000 /* 4 */
+#define AU1500_PCI_MEM_PHYS_ADDR 0x400000000ULL /* 13 */
+#define AU1500_PCI_IO_PHYS_ADDR 0x500000000ULL /* 13 */
+#define AU1500_PCI_CONFIG0_PHYS_ADDR 0x600000000ULL /* 13 */
+#define AU1500_PCI_CONFIG1_PHYS_ADDR 0x680000000ULL /* 13 */
+#define AU1000_PCMCIA_IO_PHYS_ADDR 0xF00000000ULL /* 01234 */
+#define AU1000_PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL /* 01234 */
+#define AU1000_PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL /* 01234 */
-#ifdef CONFIG_SOC_AU1000
-#define MEM_PHYS_ADDR 0x14000000
-#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define IRDA_PHYS_ADDR 0x10300000
-#define SSI0_PHYS_ADDR 0x11600000
-#define SSI1_PHYS_ADDR 0x11680000
-#define PCMCIA_IO_PHYS_ADDR 0xF00000000ULL
-#define PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL
-#define PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL
-#endif
-
-/********************************************************************/
-
-#ifdef CONFIG_SOC_AU1500
-#define MEM_PHYS_ADDR 0x14000000
-#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define PCI_PHYS_ADDR 0x14005000
-#define PCI_MEM_PHYS_ADDR 0x400000000ULL
-#define PCI_IO_PHYS_ADDR 0x500000000ULL
-#define PCI_CONFIG0_PHYS_ADDR 0x600000000ULL
-#define PCI_CONFIG1_PHYS_ADDR 0x680000000ULL
-#define PCMCIA_IO_PHYS_ADDR 0xF00000000ULL
-#define PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL
-#define PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL
-#endif
-
-/********************************************************************/
-
-#ifdef CONFIG_SOC_AU1100
-#define MEM_PHYS_ADDR 0x14000000
-#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define IRDA_PHYS_ADDR 0x10300000
-#define SSI0_PHYS_ADDR 0x11600000
-#define SSI1_PHYS_ADDR 0x11680000
-#define LCD_PHYS_ADDR 0x15000000
-#define PCMCIA_IO_PHYS_ADDR 0xF00000000ULL
-#define PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL
-#define PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL
-#endif
-
-/***********************************************************************/
-
-#ifdef CONFIG_SOC_AU1550
-#define MEM_PHYS_ADDR 0x14000000
-#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define PCI_PHYS_ADDR 0x14005000
-#define PE_PHYS_ADDR 0x14008000
-#define PSC0_PHYS_ADDR 0x11A00000
-#define PSC1_PHYS_ADDR 0x11B00000
-#define PSC2_PHYS_ADDR 0x10A00000
-#define PSC3_PHYS_ADDR 0x10B00000
-#define PCI_MEM_PHYS_ADDR 0x400000000ULL
-#define PCI_IO_PHYS_ADDR 0x500000000ULL
-#define PCI_CONFIG0_PHYS_ADDR 0x600000000ULL
-#define PCI_CONFIG1_PHYS_ADDR 0x680000000ULL
-#define PCMCIA_IO_PHYS_ADDR 0xF00000000ULL
-#define PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL
-#define PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL
-#endif
-
-/***********************************************************************/
-
-#ifdef CONFIG_SOC_AU1200
-#define MEM_PHYS_ADDR 0x14000000
-#define STATIC_MEM_PHYS_ADDR 0x14001000
-#define AES_PHYS_ADDR 0x10300000
-#define CIM_PHYS_ADDR 0x14004000
-#define PSC0_PHYS_ADDR 0x11A00000
-#define PSC1_PHYS_ADDR 0x11B00000
-#define LCD_PHYS_ADDR 0x15000000
-#define SWCNT_PHYS_ADDR 0x1110010C
-#define MAEFE_PHYS_ADDR 0x14012000
-#define MAEBE_PHYS_ADDR 0x14010000
-#define PCMCIA_IO_PHYS_ADDR 0xF00000000ULL
-#define PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL
-#define PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL
-#endif
-
/* Static Bus Controller */
#define MEM_STCFG0 0xB4001000
#define MEM_STTIME0 0xB4001004
diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h b/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h
index 892b7f1..8e2fa67 100644
--- a/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h
+++ b/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h
@@ -33,19 +33,6 @@
#ifndef _AU1000_PSC_H_
#define _AU1000_PSC_H_
-/* The PSC base addresses. */
-#ifdef CONFIG_SOC_AU1550
-#define PSC0_BASE_ADDR 0xb1a00000
-#define PSC1_BASE_ADDR 0xb1b00000
-#define PSC2_BASE_ADDR 0xb0a00000
-#define PSC3_BASE_ADDR 0xb0b00000
-#endif
-
-#ifdef CONFIG_SOC_AU1200
-#define PSC0_BASE_ADDR 0xb1a00000
-#define PSC1_BASE_ADDR 0xb1b00000
-#endif
-
/*
* The PSC select and control registers are common to all protocols.
*/
@@ -80,19 +67,6 @@
#define PSC_AC97GPO_OFFSET 0x00000028
#define PSC_AC97GPI_OFFSET 0x0000002c
-#define AC97_PSC_SEL (AC97_PSC_BASE + PSC_SEL_OFFSET)
-#define AC97_PSC_CTRL (AC97_PSC_BASE + PSC_CTRL_OFFSET)
-#define PSC_AC97CFG (AC97_PSC_BASE + PSC_AC97CFG_OFFSET)
-#define PSC_AC97MSK (AC97_PSC_BASE + PSC_AC97MSK_OFFSET)
-#define PSC_AC97PCR (AC97_PSC_BASE + PSC_AC97PCR_OFFSET)
-#define PSC_AC97STAT (AC97_PSC_BASE + PSC_AC97STAT_OFFSET)
-#define PSC_AC97EVNT (AC97_PSC_BASE + PSC_AC97EVNT_OFFSET)
-#define PSC_AC97TXRX (AC97_PSC_BASE + PSC_AC97TXRX_OFFSET)
-#define PSC_AC97CDC (AC97_PSC_BASE + PSC_AC97CDC_OFFSET)
-#define PSC_AC97RST (AC97_PSC_BASE + PSC_AC97RST_OFFSET)
-#define PSC_AC97GPO (AC97_PSC_BASE + PSC_AC97GPO_OFFSET)
-#define PSC_AC97GPI (AC97_PSC_BASE + PSC_AC97GPI_OFFSET)
-
/* AC97 Config Register. */
#define PSC_AC97CFG_RT_MASK (3 << 30)
#define PSC_AC97CFG_RT_FIFO1 (0 << 30)
diff --git a/arch/mips/include/asm/mach-db1x00/db1x00.h b/arch/mips/include/asm/mach-db1x00/db1x00.h
index a919dac..115cc7c 100644
--- a/arch/mips/include/asm/mach-db1x00/db1x00.h
+++ b/arch/mips/include/asm/mach-db1x00/db1x00.h
@@ -36,10 +36,10 @@
#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC3_TX
#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC3_RX
-#define SPI_PSC_BASE PSC0_BASE_ADDR
-#define AC97_PSC_BASE PSC1_BASE_ADDR
-#define SMBUS_PSC_BASE PSC2_BASE_ADDR
-#define I2S_PSC_BASE PSC3_BASE_ADDR
+#define SPI_PSC_BASE AU1550_PSC0_PHYS_ADDR
+#define AC97_PSC_BASE AU1550_PSC1_PHYS_ADDR
+#define SMBUS_PSC_BASE AU1550_PSC2_PHYS_ADDR
+#define I2S_PSC_BASE AU1550_PSC3_PHYS_ADDR
#define NAND_PHYS_ADDR 0x20000000
diff --git a/arch/mips/include/asm/mach-pb1x00/pb1200.h b/arch/mips/include/asm/mach-pb1x00/pb1200.h
index fce4332..0ecff1c 100644
--- a/arch/mips/include/asm/mach-pb1x00/pb1200.h
+++ b/arch/mips/include/asm/mach-pb1x00/pb1200.h
@@ -37,14 +37,14 @@
* SPI and SMB are muxed on the Pb1200 board.
* Refer to board documentation.
*/
-#define SPI_PSC_BASE PSC0_BASE_ADDR
-#define SMBUS_PSC_BASE PSC0_BASE_ADDR
+#define SPI_PSC_BASE AU1550_PSC0_PHYS_ADDR
+#define SMBUS_PSC_BASE AU1550_PSC0_PHYS_ADDR
/*
* AC97 and I2S are muxed on the Pb1200 board.
* Refer to board documentation.
*/
-#define AC97_PSC_BASE PSC1_BASE_ADDR
-#define I2S_PSC_BASE PSC1_BASE_ADDR
+#define AC97_PSC_BASE AU1550_PSC1_PHYS_ADDR
+#define I2S_PSC_BASE AU1550_PSC1_PHYS_ADDR
#define BCSR_SYSTEM_VDDI 0x001F
diff --git a/arch/mips/include/asm/mach-pb1x00/pb1550.h b/arch/mips/include/asm/mach-pb1x00/pb1550.h
index f835c88..0b0f462 100644
--- a/arch/mips/include/asm/mach-pb1x00/pb1550.h
+++ b/arch/mips/include/asm/mach-pb1x00/pb1550.h
@@ -35,10 +35,10 @@
#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC3_TX
#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC3_RX
-#define SPI_PSC_BASE PSC0_BASE_ADDR
-#define AC97_PSC_BASE PSC1_BASE_ADDR
-#define SMBUS_PSC_BASE PSC2_BASE_ADDR
-#define I2S_PSC_BASE PSC3_BASE_ADDR
+#define SPI_PSC_BASE AU1550_PSC0_PHYS_ADDR
+#define AC97_PSC_BASE AU1550_PSC1_PHYS_ADDR
+#define SMBUS_PSC_BASE AU1550_PSC2_PHYS_ADDR
+#define I2S_PSC_BASE AU1550_PSC3_PHYS_ADDR
/*
* Timing values as described in databook, * ns value stripped of
--
1.7.5.rc3
^ permalink raw reply related [flat|nested] 4+ messages in thread