[PATCH 1/2] can: bfin_can: simplify xmit id1 setup

[PATCH 1/2] can: bfin_can: simplify xmit id1 setup

[Mike Frysinger]

If we look closely, the 4 writes to TRANSMIT_CHL.id1 can be collapsed
down into much simpler code.  So do just that.

This also fixes a build failure due to the I/O macros no longer
getting pulled in.  Their minor (and accidental) usage here gets
dropped as part of the unification.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/net/can/bfin_can.c |   21 ++++++---------------
 1 files changed, 6 insertions(+), 15 deletions(-)

diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c
index b6e890d..dc6ef4a 100644
--- a/drivers/net/can/bfin_can.c
+++ b/drivers/net/can/bfin_can.c
@@ -243,21 +243,12 @@ static int bfin_can_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	/* fill id */
 	if (id & CAN_EFF_FLAG) {
 		bfin_write16(&reg->chl[TRANSMIT_CHL].id0, id);
-		if (id & CAN_RTR_FLAG)
-			writew(((id & 0x1FFF0000) >> 16) | IDE | AME | RTR,
-					&reg->chl[TRANSMIT_CHL].id1);
-		else
-			writew(((id & 0x1FFF0000) >> 16) | IDE | AME,
-					&reg->chl[TRANSMIT_CHL].id1);
-
-	} else {
-		if (id & CAN_RTR_FLAG)
-			writew((id << 2) | AME | RTR,
-				&reg->chl[TRANSMIT_CHL].id1);
-		else
-			bfin_write16(&reg->chl[TRANSMIT_CHL].id1,
-					(id << 2) | AME);
-	}
+		val = ((id & 0x1FFF0000) >> 16) | IDE;
+	} else
+		val = (id << 2);
+	if (id & CAN_RTR_FLAG)
+		val |= RTR;
+	bfin_write16(&reg->chl[TRANSMIT_CHL].id1, val | AME);
 
 	/* fill payload */
 	for (i = 0; i < 8; i += 2) {
-- 
1.7.5.3

[PATCH 2/2] can: bfin_can: auto-calculate accessor sizes

[Mike Frysinger]

Since we have a struct that defines the sizes of the registers, we don't
need to explicitly use the 16bit read/write helpers.  Let the code figure
out which size access to make based on the size of the C type.

There should be no functional changes here.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/net/can/bfin_can.c |  118 ++++++++++++++++++++++----------------------
 1 files changed, 59 insertions(+), 59 deletions(-)

diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c
index dc6ef4a..a1c5abc 100644
--- a/drivers/net/can/bfin_can.c
+++ b/drivers/net/can/bfin_can.c
@@ -79,8 +79,8 @@ static int bfin_can_set_bittiming(struct net_device *dev)
 	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
 		timing |= SAM;
 
-	bfin_write16(&reg->clock, clk);
-	bfin_write16(&reg->timing, timing);
+	bfin_write(&reg->clock, clk);
+	bfin_write(&reg->timing, timing);
 
 	dev_info(dev->dev.parent, "setting CLOCK=0x%04x TIMING=0x%04x\n",
 			clk, timing);
@@ -96,16 +96,16 @@ static void bfin_can_set_reset_mode(struct net_device *dev)
 	int i;
 
 	/* disable interrupts */
-	bfin_write16(&reg->mbim1, 0);
-	bfin_write16(&reg->mbim2, 0);
-	bfin_write16(&reg->gim, 0);
+	bfin_write(&reg->mbim1, 0);
+	bfin_write(&reg->mbim2, 0);
+	bfin_write(&reg->gim, 0);
 
 	/* reset can and enter configuration mode */
-	bfin_write16(&reg->control, SRS | CCR);
+	bfin_write(&reg->control, SRS | CCR);
 	SSYNC();
-	bfin_write16(&reg->control, CCR);
+	bfin_write(&reg->control, CCR);
 	SSYNC();
-	while (!(bfin_read16(&reg->control) & CCA)) {
+	while (!(bfin_read(&reg->control) & CCA)) {
 		udelay(10);
 		if (--timeout == 0) {
 			dev_err(dev->dev.parent,
@@ -119,33 +119,33 @@ static void bfin_can_set_reset_mode(struct net_device *dev)
 	 * by writing to CAN Mailbox Configuration Registers 1 and 2
 	 * For all bits: 0 - Mailbox disabled, 1 - Mailbox enabled
 	 */
-	bfin_write16(&reg->mc1, 0);
-	bfin_write16(&reg->mc2, 0);
+	bfin_write(&reg->mc1, 0);
+	bfin_write(&reg->mc2, 0);
 
 	/* Set Mailbox Direction */
-	bfin_write16(&reg->md1, 0xFFFF);   /* mailbox 1-16 are RX */
-	bfin_write16(&reg->md2, 0);   /* mailbox 17-32 are TX */
+	bfin_write(&reg->md1, 0xFFFF);   /* mailbox 1-16 are RX */
+	bfin_write(&reg->md2, 0);   /* mailbox 17-32 are TX */
 
 	/* RECEIVE_STD_CHL */
 	for (i = 0; i < 2; i++) {
-		bfin_write16(&reg->chl[RECEIVE_STD_CHL + i].id0, 0);
-		bfin_write16(&reg->chl[RECEIVE_STD_CHL + i].id1, AME);
-		bfin_write16(&reg->chl[RECEIVE_STD_CHL + i].dlc, 0);
-		bfin_write16(&reg->msk[RECEIVE_STD_CHL + i].amh, 0x1FFF);
-		bfin_write16(&reg->msk[RECEIVE_STD_CHL + i].aml, 0xFFFF);
+		bfin_write(&reg->chl[RECEIVE_STD_CHL + i].id0, 0);
+		bfin_write(&reg->chl[RECEIVE_STD_CHL + i].id1, AME);
+		bfin_write(&reg->chl[RECEIVE_STD_CHL + i].dlc, 0);
+		bfin_write(&reg->msk[RECEIVE_STD_CHL + i].amh, 0x1FFF);
+		bfin_write(&reg->msk[RECEIVE_STD_CHL + i].aml, 0xFFFF);
 	}
 
 	/* RECEIVE_EXT_CHL */
 	for (i = 0; i < 2; i++) {
-		bfin_write16(&reg->chl[RECEIVE_EXT_CHL + i].id0, 0);
-		bfin_write16(&reg->chl[RECEIVE_EXT_CHL + i].id1, AME | IDE);
-		bfin_write16(&reg->chl[RECEIVE_EXT_CHL + i].dlc, 0);
-		bfin_write16(&reg->msk[RECEIVE_EXT_CHL + i].amh, 0x1FFF);
-		bfin_write16(&reg->msk[RECEIVE_EXT_CHL + i].aml, 0xFFFF);
+		bfin_write(&reg->chl[RECEIVE_EXT_CHL + i].id0, 0);
+		bfin_write(&reg->chl[RECEIVE_EXT_CHL + i].id1, AME | IDE);
+		bfin_write(&reg->chl[RECEIVE_EXT_CHL + i].dlc, 0);
+		bfin_write(&reg->msk[RECEIVE_EXT_CHL + i].amh, 0x1FFF);
+		bfin_write(&reg->msk[RECEIVE_EXT_CHL + i].aml, 0xFFFF);
 	}
 
-	bfin_write16(&reg->mc2, BIT(TRANSMIT_CHL - 16));
-	bfin_write16(&reg->mc1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
+	bfin_write(&reg->mc2, BIT(TRANSMIT_CHL - 16));
+	bfin_write(&reg->mc1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
 	SSYNC();
 
 	priv->can.state = CAN_STATE_STOPPED;
@@ -160,9 +160,9 @@ static void bfin_can_set_normal_mode(struct net_device *dev)
 	/*
 	 * leave configuration mode
 	 */
-	bfin_write16(&reg->control, bfin_read16(&reg->control) & ~CCR);
+	bfin_write(&reg->control, bfin_read(&reg->control) & ~CCR);
 
-	while (bfin_read16(&reg->status) & CCA) {
+	while (bfin_read(&reg->status) & CCA) {
 		udelay(10);
 		if (--timeout == 0) {
 			dev_err(dev->dev.parent,
@@ -174,25 +174,25 @@ static void bfin_can_set_normal_mode(struct net_device *dev)
 	/*
 	 * clear _All_  tx and rx interrupts
 	 */
-	bfin_write16(&reg->mbtif1, 0xFFFF);
-	bfin_write16(&reg->mbtif2, 0xFFFF);
-	bfin_write16(&reg->mbrif1, 0xFFFF);
-	bfin_write16(&reg->mbrif2, 0xFFFF);
+	bfin_write(&reg->mbtif1, 0xFFFF);
+	bfin_write(&reg->mbtif2, 0xFFFF);
+	bfin_write(&reg->mbrif1, 0xFFFF);
+	bfin_write(&reg->mbrif2, 0xFFFF);
 
 	/*
 	 * clear global interrupt status register
 	 */
-	bfin_write16(&reg->gis, 0x7FF); /* overwrites with '1' */
+	bfin_write(&reg->gis, 0x7FF); /* overwrites with '1' */
 
 	/*
 	 * Initialize Interrupts
 	 * - set bits in the mailbox interrupt mask register
 	 * - global interrupt mask
 	 */
-	bfin_write16(&reg->mbim1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
-	bfin_write16(&reg->mbim2, BIT(TRANSMIT_CHL - 16));
+	bfin_write(&reg->mbim1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
+	bfin_write(&reg->mbim2, BIT(TRANSMIT_CHL - 16));
 
-	bfin_write16(&reg->gim, EPIM | BOIM | RMLIM);
+	bfin_write(&reg->gim, EPIM | BOIM | RMLIM);
 	SSYNC();
 }
 
@@ -242,28 +242,28 @@ static int bfin_can_start_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	/* fill id */
 	if (id & CAN_EFF_FLAG) {
-		bfin_write16(&reg->chl[TRANSMIT_CHL].id0, id);
+		bfin_write(&reg->chl[TRANSMIT_CHL].id0, id);
 		val = ((id & 0x1FFF0000) >> 16) | IDE;
 	} else
 		val = (id << 2);
 	if (id & CAN_RTR_FLAG)
 		val |= RTR;
-	bfin_write16(&reg->chl[TRANSMIT_CHL].id1, val | AME);
+	bfin_write(&reg->chl[TRANSMIT_CHL].id1, val | AME);
 
 	/* fill payload */
 	for (i = 0; i < 8; i += 2) {
 		val = ((7 - i) < dlc ? (data[7 - i]) : 0) +
 			((6 - i) < dlc ? (data[6 - i] << 8) : 0);
-		bfin_write16(&reg->chl[TRANSMIT_CHL].data[i], val);
+		bfin_write(&reg->chl[TRANSMIT_CHL].data[i], val);
 	}
 
 	/* fill data length code */
-	bfin_write16(&reg->chl[TRANSMIT_CHL].dlc, dlc);
+	bfin_write(&reg->chl[TRANSMIT_CHL].dlc, dlc);
 
 	can_put_echo_skb(skb, dev, 0);
 
 	/* set transmit request */
-	bfin_write16(&reg->trs2, BIT(TRANSMIT_CHL - 16));
+	bfin_write(&reg->trs2, BIT(TRANSMIT_CHL - 16));
 
 	return 0;
 }
@@ -286,26 +286,26 @@ static void bfin_can_rx(struct net_device *dev, u16 isrc)
 	/* get id */
 	if (isrc & BIT(RECEIVE_EXT_CHL)) {
 		/* extended frame format (EFF) */
-		cf->can_id = ((bfin_read16(&reg->chl[RECEIVE_EXT_CHL].id1)
+		cf->can_id = ((bfin_read(&reg->chl[RECEIVE_EXT_CHL].id1)
 			     & 0x1FFF) << 16)
-			     + bfin_read16(&reg->chl[RECEIVE_EXT_CHL].id0);
+			     + bfin_read(&reg->chl[RECEIVE_EXT_CHL].id0);
 		cf->can_id |= CAN_EFF_FLAG;
 		obj = RECEIVE_EXT_CHL;
 	} else {
 		/* standard frame format (SFF) */
-		cf->can_id = (bfin_read16(&reg->chl[RECEIVE_STD_CHL].id1)
+		cf->can_id = (bfin_read(&reg->chl[RECEIVE_STD_CHL].id1)
 			     & 0x1ffc) >> 2;
 		obj = RECEIVE_STD_CHL;
 	}
-	if (bfin_read16(&reg->chl[obj].id1) & RTR)
+	if (bfin_read(&reg->chl[obj].id1) & RTR)
 		cf->can_id |= CAN_RTR_FLAG;
 
 	/* get data length code */
-	cf->can_dlc = get_can_dlc(bfin_read16(&reg->chl[obj].dlc) & 0xF);
+	cf->can_dlc = get_can_dlc(bfin_read(&reg->chl[obj].dlc) & 0xF);
 
 	/* get payload */
 	for (i = 0; i < 8; i += 2) {
-		val = bfin_read16(&reg->chl[obj].data[i]);
+		val = bfin_read(&reg->chl[obj].data[i]);
 		cf->data[7 - i] = (7 - i) < cf->can_dlc ? val : 0;
 		cf->data[6 - i] = (6 - i) < cf->can_dlc ? (val >> 8) : 0;
 	}
@@ -359,7 +359,7 @@ static int bfin_can_err(struct net_device *dev, u16 isrc, u16 status)
 
 	if (state != priv->can.state && (state == CAN_STATE_ERROR_WARNING ||
 				state == CAN_STATE_ERROR_PASSIVE)) {
-		u16 cec = bfin_read16(&reg->cec);
+		u16 cec = bfin_read(&reg->cec);
 		u8 rxerr = cec;
 		u8 txerr = cec >> 8;
 
@@ -410,23 +410,23 @@ irqreturn_t bfin_can_interrupt(int irq, void *dev_id)
 	struct net_device_stats *stats = &dev->stats;
 	u16 status, isrc;
 
-	if ((irq == priv->tx_irq) && bfin_read16(&reg->mbtif2)) {
+	if ((irq == priv->tx_irq) && bfin_read(&reg->mbtif2)) {
 		/* transmission complete interrupt */
-		bfin_write16(&reg->mbtif2, 0xFFFF);
+		bfin_write(&reg->mbtif2, 0xFFFF);
 		stats->tx_packets++;
-		stats->tx_bytes += bfin_read16(&reg->chl[TRANSMIT_CHL].dlc);
+		stats->tx_bytes += bfin_read(&reg->chl[TRANSMIT_CHL].dlc);
 		can_get_echo_skb(dev, 0);
 		netif_wake_queue(dev);
-	} else if ((irq == priv->rx_irq) && bfin_read16(&reg->mbrif1)) {
+	} else if ((irq == priv->rx_irq) && bfin_read(&reg->mbrif1)) {
 		/* receive interrupt */
-		isrc = bfin_read16(&reg->mbrif1);
-		bfin_write16(&reg->mbrif1, 0xFFFF);
+		isrc = bfin_read(&reg->mbrif1);
+		bfin_write(&reg->mbrif1, 0xFFFF);
 		bfin_can_rx(dev, isrc);
-	} else if ((irq == priv->err_irq) && bfin_read16(&reg->gis)) {
+	} else if ((irq == priv->err_irq) && bfin_read(&reg->gis)) {
 		/* error interrupt */
-		isrc = bfin_read16(&reg->gis);
-		status = bfin_read16(&reg->esr);
-		bfin_write16(&reg->gis, 0x7FF);
+		isrc = bfin_read(&reg->gis);
+		status = bfin_read(&reg->esr);
+		bfin_write(&reg->gis, 0x7FF);
 		bfin_can_err(dev, isrc, status);
 	} else {
 		return IRQ_NONE;
@@ -631,9 +631,9 @@ static int bfin_can_suspend(struct platform_device *pdev, pm_message_t mesg)
 
 	if (netif_running(dev)) {
 		/* enter sleep mode */
-		bfin_write16(&reg->control, bfin_read16(&reg->control) | SMR);
+		bfin_write(&reg->control, bfin_read(&reg->control) | SMR);
 		SSYNC();
-		while (!(bfin_read16(&reg->intr) & SMACK)) {
+		while (!(bfin_read(&reg->intr) & SMACK)) {
 			udelay(10);
 			if (--timeout == 0) {
 				dev_err(dev->dev.parent,
@@ -654,7 +654,7 @@ static int bfin_can_resume(struct platform_device *pdev)
 
 	if (netif_running(dev)) {
 		/* leave sleep mode */
-		bfin_write16(&reg->intr, 0);
+		bfin_write(&reg->intr, 0);
 		SSYNC();
 	}
 
-- 
1.7.5.3

Re: [PATCH 1/2] can: bfin_can: simplify xmit id1 setup

[Oliver Hartkopp]

Am 23.06.2011 22:36, schrieb Mike Frysinger:
> If we look closely, the 4 writes to TRANSMIT_CHL.id1 can be collapsed
> down into much simpler code.  So do just that.

Hello Mike,

unfortunately you addressed the wrong people to ack your patch.

In MAINTAINERS there are entries for the CAN NETWORK LAYER and for CAN 
NETWORK DRIVERS which addresses the code in drivers/net/can/...

Additionally you should address your patch to the author of the driver 
(Barry Song <21cnbao-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>).

Tnx & best regards,
Oliver



>
> This also fixes a build failure due to the I/O macros no longer
> getting pulled in.  Their minor (and accidental) usage here gets
> dropped as part of the unification.
>
> Signed-off-by: Mike Frysinger<vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
> ---
>   drivers/net/can/bfin_can.c |   21 ++++++---------------
>   1 files changed, 6 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c
> index b6e890d..dc6ef4a 100644
> --- a/drivers/net/can/bfin_can.c
> +++ b/drivers/net/can/bfin_can.c
> @@ -243,21 +243,12 @@ static int bfin_can_start_xmit(struct sk_buff *skb, struct net_device *dev)
>   	/* fill id */
>   	if (id&  CAN_EFF_FLAG) {
>   		bfin_write16(&reg->chl[TRANSMIT_CHL].id0, id);
> -		if (id&  CAN_RTR_FLAG)
> -			writew(((id&  0x1FFF0000)>>  16) | IDE | AME | RTR,
> -					&reg->chl[TRANSMIT_CHL].id1);
> -		else
> -			writew(((id&  0x1FFF0000)>>  16) | IDE | AME,
> -					&reg->chl[TRANSMIT_CHL].id1);
> -
> -	} else {
> -		if (id&  CAN_RTR_FLAG)
> -			writew((id<<  2) | AME | RTR,
> -				&reg->chl[TRANSMIT_CHL].id1);
> -		else
> -			bfin_write16(&reg->chl[TRANSMIT_CHL].id1,
> -					(id<<  2) | AME);
> -	}
> +		val = ((id&  0x1FFF0000)>>  16) | IDE;
> +	} else
> +		val = (id<<  2);
> +	if (id&  CAN_RTR_FLAG)
> +		val |= RTR;
> +	bfin_write16(&reg->chl[TRANSMIT_CHL].id1, val | AME);
>
>   	/* fill payload */
>   	for (i = 0; i<  8; i += 2) {

Re: [uclinux-dist-devel] [PATCH 1/2] can: bfin_can: simplify xmit id1 setup

[Mike Frysinger]

On Fri, Jun 24, 2011 at 06:46, Oliver Hartkopp wrote:
> In MAINTAINERS there are entries for the CAN NETWORK LAYER and for CAN
> NETWORK DRIVERS which addresses the code in drivers/net/can/...

hmm, wonder when this changed.  oh well, updated local .git/mail now.

> Additionally you should address your patch to the author of the driver
> (Barry Song <21cnbao-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>).

he's already in the cc list.  he's an ADI employee (like me) who
watches the Blackfin mailing lists.
-mike

Re: [PATCH 2/2] can: bfin_can: auto-calculate accessor sizes

[David Miller]

From: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
Date: Fri, 24 Jun 2011 10:33:02 -0400

> Since we have a struct that defines the sizes of the registers, we don't
> need to explicitly use the 16bit read/write helpers.  Let the code figure
> out which size access to make based on the size of the C type.
> 
> There should be no functional changes here.
> 
> Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>

Applied.

Re: [PATCH 2/2] can: bfin_can: auto-calculate accessor sizes

[Wolfgang Grandegger]

On 06/24/2011 04:33 PM, Mike Frysinger wrote:
> Since we have a struct that defines the sizes of the registers, we don't
> need to explicitly use the 16bit read/write helpers.  Let the code figure
> out which size access to make based on the size of the C type.
> 
> There should be no functional changes here.
> 
> Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>

Acked-by: Wolfgang Grandegger <wg-5Yr1BZd7O62+XT7JhA+gdA@public.gmane.org>

Thanks,

Wolfgang,

[PATCH 2/2] can: bfin_can: auto-calculate accessor sizes

[Mike Frysinger]

Since we have a struct that defines the sizes of the registers, we don't
need to explicitly use the 16bit read/write helpers.  Let the code figure
out which size access to make based on the size of the C type.

There should be no functional changes here.

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/net/can/bfin_can.c |  118 ++++++++++++++++++++++----------------------
 1 files changed, 59 insertions(+), 59 deletions(-)

diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c
index dc6ef4a..a1c5abc 100644
--- a/drivers/net/can/bfin_can.c
+++ b/drivers/net/can/bfin_can.c
@@ -79,8 +79,8 @@ static int bfin_can_set_bittiming(struct net_device *dev)
 	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
 		timing |= SAM;
 
-	bfin_write16(&reg->clock, clk);
-	bfin_write16(&reg->timing, timing);
+	bfin_write(&reg->clock, clk);
+	bfin_write(&reg->timing, timing);
 
 	dev_info(dev->dev.parent, "setting CLOCK=0x%04x TIMING=0x%04x\n",
 			clk, timing);
@@ -96,16 +96,16 @@ static void bfin_can_set_reset_mode(struct net_device *dev)
 	int i;
 
 	/* disable interrupts */
-	bfin_write16(&reg->mbim1, 0);
-	bfin_write16(&reg->mbim2, 0);
-	bfin_write16(&reg->gim, 0);
+	bfin_write(&reg->mbim1, 0);
+	bfin_write(&reg->mbim2, 0);
+	bfin_write(&reg->gim, 0);
 
 	/* reset can and enter configuration mode */
-	bfin_write16(&reg->control, SRS | CCR);
+	bfin_write(&reg->control, SRS | CCR);
 	SSYNC();
-	bfin_write16(&reg->control, CCR);
+	bfin_write(&reg->control, CCR);
 	SSYNC();
-	while (!(bfin_read16(&reg->control) & CCA)) {
+	while (!(bfin_read(&reg->control) & CCA)) {
 		udelay(10);
 		if (--timeout == 0) {
 			dev_err(dev->dev.parent,
@@ -119,33 +119,33 @@ static void bfin_can_set_reset_mode(struct net_device *dev)
 	 * by writing to CAN Mailbox Configuration Registers 1 and 2
 	 * For all bits: 0 - Mailbox disabled, 1 - Mailbox enabled
 	 */
-	bfin_write16(&reg->mc1, 0);
-	bfin_write16(&reg->mc2, 0);
+	bfin_write(&reg->mc1, 0);
+	bfin_write(&reg->mc2, 0);
 
 	/* Set Mailbox Direction */
-	bfin_write16(&reg->md1, 0xFFFF);   /* mailbox 1-16 are RX */
-	bfin_write16(&reg->md2, 0);   /* mailbox 17-32 are TX */
+	bfin_write(&reg->md1, 0xFFFF);   /* mailbox 1-16 are RX */
+	bfin_write(&reg->md2, 0);   /* mailbox 17-32 are TX */
 
 	/* RECEIVE_STD_CHL */
 	for (i = 0; i < 2; i++) {
-		bfin_write16(&reg->chl[RECEIVE_STD_CHL + i].id0, 0);
-		bfin_write16(&reg->chl[RECEIVE_STD_CHL + i].id1, AME);
-		bfin_write16(&reg->chl[RECEIVE_STD_CHL + i].dlc, 0);
-		bfin_write16(&reg->msk[RECEIVE_STD_CHL + i].amh, 0x1FFF);
-		bfin_write16(&reg->msk[RECEIVE_STD_CHL + i].aml, 0xFFFF);
+		bfin_write(&reg->chl[RECEIVE_STD_CHL + i].id0, 0);
+		bfin_write(&reg->chl[RECEIVE_STD_CHL + i].id1, AME);
+		bfin_write(&reg->chl[RECEIVE_STD_CHL + i].dlc, 0);
+		bfin_write(&reg->msk[RECEIVE_STD_CHL + i].amh, 0x1FFF);
+		bfin_write(&reg->msk[RECEIVE_STD_CHL + i].aml, 0xFFFF);
 	}
 
 	/* RECEIVE_EXT_CHL */
 	for (i = 0; i < 2; i++) {
-		bfin_write16(&reg->chl[RECEIVE_EXT_CHL + i].id0, 0);
-		bfin_write16(&reg->chl[RECEIVE_EXT_CHL + i].id1, AME | IDE);
-		bfin_write16(&reg->chl[RECEIVE_EXT_CHL + i].dlc, 0);
-		bfin_write16(&reg->msk[RECEIVE_EXT_CHL + i].amh, 0x1FFF);
-		bfin_write16(&reg->msk[RECEIVE_EXT_CHL + i].aml, 0xFFFF);
+		bfin_write(&reg->chl[RECEIVE_EXT_CHL + i].id0, 0);
+		bfin_write(&reg->chl[RECEIVE_EXT_CHL + i].id1, AME | IDE);
+		bfin_write(&reg->chl[RECEIVE_EXT_CHL + i].dlc, 0);
+		bfin_write(&reg->msk[RECEIVE_EXT_CHL + i].amh, 0x1FFF);
+		bfin_write(&reg->msk[RECEIVE_EXT_CHL + i].aml, 0xFFFF);
 	}
 
-	bfin_write16(&reg->mc2, BIT(TRANSMIT_CHL - 16));
-	bfin_write16(&reg->mc1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
+	bfin_write(&reg->mc2, BIT(TRANSMIT_CHL - 16));
+	bfin_write(&reg->mc1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
 	SSYNC();
 
 	priv->can.state = CAN_STATE_STOPPED;
@@ -160,9 +160,9 @@ static void bfin_can_set_normal_mode(struct net_device *dev)
 	/*
 	 * leave configuration mode
 	 */
-	bfin_write16(&reg->control, bfin_read16(&reg->control) & ~CCR);
+	bfin_write(&reg->control, bfin_read(&reg->control) & ~CCR);
 
-	while (bfin_read16(&reg->status) & CCA) {
+	while (bfin_read(&reg->status) & CCA) {
 		udelay(10);
 		if (--timeout == 0) {
 			dev_err(dev->dev.parent,
@@ -174,25 +174,25 @@ static void bfin_can_set_normal_mode(struct net_device *dev)
 	/*
 	 * clear _All_  tx and rx interrupts
 	 */
-	bfin_write16(&reg->mbtif1, 0xFFFF);
-	bfin_write16(&reg->mbtif2, 0xFFFF);
-	bfin_write16(&reg->mbrif1, 0xFFFF);
-	bfin_write16(&reg->mbrif2, 0xFFFF);
+	bfin_write(&reg->mbtif1, 0xFFFF);
+	bfin_write(&reg->mbtif2, 0xFFFF);
+	bfin_write(&reg->mbrif1, 0xFFFF);
+	bfin_write(&reg->mbrif2, 0xFFFF);
 
 	/*
 	 * clear global interrupt status register
 	 */
-	bfin_write16(&reg->gis, 0x7FF); /* overwrites with '1' */
+	bfin_write(&reg->gis, 0x7FF); /* overwrites with '1' */
 
 	/*
 	 * Initialize Interrupts
 	 * - set bits in the mailbox interrupt mask register
 	 * - global interrupt mask
 	 */
-	bfin_write16(&reg->mbim1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
-	bfin_write16(&reg->mbim2, BIT(TRANSMIT_CHL - 16));
+	bfin_write(&reg->mbim1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
+	bfin_write(&reg->mbim2, BIT(TRANSMIT_CHL - 16));
 
-	bfin_write16(&reg->gim, EPIM | BOIM | RMLIM);
+	bfin_write(&reg->gim, EPIM | BOIM | RMLIM);
 	SSYNC();
 }
 
@@ -242,28 +242,28 @@ static int bfin_can_start_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	/* fill id */
 	if (id & CAN_EFF_FLAG) {
-		bfin_write16(&reg->chl[TRANSMIT_CHL].id0, id);
+		bfin_write(&reg->chl[TRANSMIT_CHL].id0, id);
 		val = ((id & 0x1FFF0000) >> 16) | IDE;
 	} else
 		val = (id << 2);
 	if (id & CAN_RTR_FLAG)
 		val |= RTR;
-	bfin_write16(&reg->chl[TRANSMIT_CHL].id1, val | AME);
+	bfin_write(&reg->chl[TRANSMIT_CHL].id1, val | AME);
 
 	/* fill payload */
 	for (i = 0; i < 8; i += 2) {
 		val = ((7 - i) < dlc ? (data[7 - i]) : 0) +
 			((6 - i) < dlc ? (data[6 - i] << 8) : 0);
-		bfin_write16(&reg->chl[TRANSMIT_CHL].data[i], val);
+		bfin_write(&reg->chl[TRANSMIT_CHL].data[i], val);
 	}
 
 	/* fill data length code */
-	bfin_write16(&reg->chl[TRANSMIT_CHL].dlc, dlc);
+	bfin_write(&reg->chl[TRANSMIT_CHL].dlc, dlc);
 
 	can_put_echo_skb(skb, dev, 0);
 
 	/* set transmit request */
-	bfin_write16(&reg->trs2, BIT(TRANSMIT_CHL - 16));
+	bfin_write(&reg->trs2, BIT(TRANSMIT_CHL - 16));
 
 	return 0;
 }
@@ -286,26 +286,26 @@ static void bfin_can_rx(struct net_device *dev, u16 isrc)
 	/* get id */
 	if (isrc & BIT(RECEIVE_EXT_CHL)) {
 		/* extended frame format (EFF) */
-		cf->can_id = ((bfin_read16(&reg->chl[RECEIVE_EXT_CHL].id1)
+		cf->can_id = ((bfin_read(&reg->chl[RECEIVE_EXT_CHL].id1)
 			     & 0x1FFF) << 16)
-			     + bfin_read16(&reg->chl[RECEIVE_EXT_CHL].id0);
+			     + bfin_read(&reg->chl[RECEIVE_EXT_CHL].id0);
 		cf->can_id |= CAN_EFF_FLAG;
 		obj = RECEIVE_EXT_CHL;
 	} else {
 		/* standard frame format (SFF) */
-		cf->can_id = (bfin_read16(&reg->chl[RECEIVE_STD_CHL].id1)
+		cf->can_id = (bfin_read(&reg->chl[RECEIVE_STD_CHL].id1)
 			     & 0x1ffc) >> 2;
 		obj = RECEIVE_STD_CHL;
 	}
-	if (bfin_read16(&reg->chl[obj].id1) & RTR)
+	if (bfin_read(&reg->chl[obj].id1) & RTR)
 		cf->can_id |= CAN_RTR_FLAG;
 
 	/* get data length code */
-	cf->can_dlc = get_can_dlc(bfin_read16(&reg->chl[obj].dlc) & 0xF);
+	cf->can_dlc = get_can_dlc(bfin_read(&reg->chl[obj].dlc) & 0xF);
 
 	/* get payload */
 	for (i = 0; i < 8; i += 2) {
-		val = bfin_read16(&reg->chl[obj].data[i]);
+		val = bfin_read(&reg->chl[obj].data[i]);
 		cf->data[7 - i] = (7 - i) < cf->can_dlc ? val : 0;
 		cf->data[6 - i] = (6 - i) < cf->can_dlc ? (val >> 8) : 0;
 	}
@@ -359,7 +359,7 @@ static int bfin_can_err(struct net_device *dev, u16 isrc, u16 status)
 
 	if (state != priv->can.state && (state == CAN_STATE_ERROR_WARNING ||
 				state == CAN_STATE_ERROR_PASSIVE)) {
-		u16 cec = bfin_read16(&reg->cec);
+		u16 cec = bfin_read(&reg->cec);
 		u8 rxerr = cec;
 		u8 txerr = cec >> 8;
 
@@ -410,23 +410,23 @@ irqreturn_t bfin_can_interrupt(int irq, void *dev_id)
 	struct net_device_stats *stats = &dev->stats;
 	u16 status, isrc;
 
-	if ((irq == priv->tx_irq) && bfin_read16(&reg->mbtif2)) {
+	if ((irq == priv->tx_irq) && bfin_read(&reg->mbtif2)) {
 		/* transmission complete interrupt */
-		bfin_write16(&reg->mbtif2, 0xFFFF);
+		bfin_write(&reg->mbtif2, 0xFFFF);
 		stats->tx_packets++;
-		stats->tx_bytes += bfin_read16(&reg->chl[TRANSMIT_CHL].dlc);
+		stats->tx_bytes += bfin_read(&reg->chl[TRANSMIT_CHL].dlc);
 		can_get_echo_skb(dev, 0);
 		netif_wake_queue(dev);
-	} else if ((irq == priv->rx_irq) && bfin_read16(&reg->mbrif1)) {
+	} else if ((irq == priv->rx_irq) && bfin_read(&reg->mbrif1)) {
 		/* receive interrupt */
-		isrc = bfin_read16(&reg->mbrif1);
-		bfin_write16(&reg->mbrif1, 0xFFFF);
+		isrc = bfin_read(&reg->mbrif1);
+		bfin_write(&reg->mbrif1, 0xFFFF);
 		bfin_can_rx(dev, isrc);
-	} else if ((irq == priv->err_irq) && bfin_read16(&reg->gis)) {
+	} else if ((irq == priv->err_irq) && bfin_read(&reg->gis)) {
 		/* error interrupt */
-		isrc = bfin_read16(&reg->gis);
-		status = bfin_read16(&reg->esr);
-		bfin_write16(&reg->gis, 0x7FF);
+		isrc = bfin_read(&reg->gis);
+		status = bfin_read(&reg->esr);
+		bfin_write(&reg->gis, 0x7FF);
 		bfin_can_err(dev, isrc, status);
 	} else {
 		return IRQ_NONE;
@@ -631,9 +631,9 @@ static int bfin_can_suspend(struct platform_device *pdev, pm_message_t mesg)
 
 	if (netif_running(dev)) {
 		/* enter sleep mode */
-		bfin_write16(&reg->control, bfin_read16(&reg->control) | SMR);
+		bfin_write(&reg->control, bfin_read(&reg->control) | SMR);
 		SSYNC();
-		while (!(bfin_read16(&reg->intr) & SMACK)) {
+		while (!(bfin_read(&reg->intr) & SMACK)) {
 			udelay(10);
 			if (--timeout == 0) {
 				dev_err(dev->dev.parent,
@@ -654,7 +654,7 @@ static int bfin_can_resume(struct platform_device *pdev)
 
 	if (netif_running(dev)) {
 		/* leave sleep mode */
-		bfin_write16(&reg->intr, 0);
+		bfin_write(&reg->intr, 0);
 		SSYNC();
 	}
 
-- 
1.7.5.3