[U-Boot] [PATCH V3] mx31: provide readable WEIM CS accessor

[Helmut Raiger <helmut.raiger@hale.at>]

setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
---
V2:
	added sys_proto.h for mx31
	introduced mxc_setup_weimcs(), which is SOC independent
	not inlined any more (codesize increased by 60-90 bytes)
V3:
	modified register access according to the coding style
---
 arch/arm/cpu/arm1136/mx31/generic.c         |    9 +++
 arch/arm/include/asm/arch-mx31/imx-regs.h   |   35 ++++++++++-
 arch/arm/include/asm/arch-mx31/sys_proto.h  |   35 +++++++++++
 board/davedenx/qong/qong.c                  |   87 ++++++++++-----------------
 board/freescale/mx31ads/mx31ads.c           |   15 ++++-
 board/freescale/mx31pdk/mx31pdk.c           |   14 ++++-
 board/imx31_phycore/imx31_phycore.c         |   41 ++++++++++---
 board/logicpd/imx31_litekit/imx31_litekit.c |   28 +++++++--
 8 files changed, 185 insertions(+), 79 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-mx31/sys_proto.h

diff --git a/arch/arm/cpu/arm1136/mx31/generic.c b/arch/arm/cpu/arm1136/mx31/generic.c
index e3a4d1b..29af156 100644
--- a/arch/arm/cpu/arm1136/mx31/generic.c
+++ b/arch/arm/cpu/arm1136/mx31/generic.c
@@ -25,6 +25,8 @@
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/clock.h>
 #include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+
 
 static u32 mx31_decode_pll(u32 reg, u32 infreq)
 {
@@ -126,6 +128,13 @@ void mx31_set_pad(enum iomux_pins pin, u32 config)
 
 }
 
+void mxc_setup_weimcs(int cs, const struct mxc_weimcs *weimcs)
+{
+	writel(weimcs->upper, WEIM_CSCR_U(cs));
+	writel(weimcs->lower, WEIM_CSCR_L(cs));
+	writel(weimcs->additional, WEIM_CSCR_A(cs));
+}
+
 struct mx3_cpu_type mx31_cpu_type[] = {
 	{ .srev = 0x00, .v = 0x10 },
 	{ .srev = 0x10, .v = 0x11 },
diff --git a/arch/arm/include/asm/arch-mx31/imx-regs.h b/arch/arm/include/asm/arch-mx31/imx-regs.h
index 2064870..02b471f 100644
--- a/arch/arm/include/asm/arch-mx31/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx31/imx-regs.h
@@ -470,6 +470,18 @@ enum iomux_pins {
 #define CCM_RCSR_NF16B	(1 << 31)
 #define CCM_RCSR_NFMS	(1 << 30)
 
+/* WEIM CS control registers */
+struct mx31_weim_cscr {
+	u32 upper;
+	u32 lower;
+	u32 additional;
+	u32 reserved;
+};
+
+struct mx31_weim {
+	struct mx31_weim_cscr cscr[6];
+};
+
 #endif
 
 #define __REG(x)     (*((volatile u32 *)(x)))
@@ -534,10 +546,27 @@ enum iomux_pins {
 #define ESDCTL_BL(x)			((x) << 7)
 #define ESDCTL_PRCT(x)			((x) << 0)
 
+/* 13 fields of the upper CS control register */
+#define CSCR_U(sp, wp, bcd, bcs, psz, pme, sync, dol, \
+		cnc, wsc, ew, wws, edc) \
+	((sp) << 31 | (wp) << 30 | (bcd) << 28 | (psz) << 22 | (pme) << 21 |\
+	 (sync) << 20 | (dol) << 16 | (cnc) << 14 | (wsc) << 8 | (ew) << 7 |\
+	 (wws) << 4 | (edc) << 0)
+/* 12 fields of the lower CS control register */
+#define CSCR_L(oea, oen, ebwa, ebwn, \
+		csa, ebc, dsz, csn, psr, cre, wrap, csen) \
+	((oea) << 28 | (oen) << 24 | (ebwa) << 20 | (ebwn) << 16 |\
+	 (csa) << 12 | (ebc) << 11 | (dsz) << 8 | (csn) << 4 |\
+	 (psr) << 3 | (cre) << 2 | (wrap) << 1 | (csen) << 0)
+/* 14 fields of the additional CS control register */
+#define CSCR_A(ebra, ebrn, rwa, rwn, mum, lah, lbn, lba, dww, dct, \
+		wwu, age, cnc2, fce) \
+	((ebra) << 28 | (ebrn) << 24 | (rwa) << 20 | (rwn) << 16 |\
+	 (mum) << 15 | (lah) << 13 | (lbn) << 10 | (lba) << 8 |\
+	 (dww) << 6 | (dct) << 4 | (wwu) << 3 |\
+	 (age) << 2 | (cnc2) << 1 | (fce) << 0)
+
 #define WEIM_BASE	0xb8002000
-#define CSCR_U(x)	(WEIM_BASE + (x) * 0x10)
-#define CSCR_L(x)	(WEIM_BASE + 4 + (x) * 0x10)
-#define CSCR_A(x)	(WEIM_BASE + 8 + (x) * 0x10)
 
 #define IOMUXC_BASE	0x43FAC000
 #define IOMUXC_GPR	(IOMUXC_BASE + 0x8)
diff --git a/arch/arm/include/asm/arch-mx31/sys_proto.h b/arch/arm/include/asm/arch-mx31/sys_proto.h
new file mode 100644
index 0000000..7600303
--- /dev/null
+++ b/arch/arm/include/asm/arch-mx31/sys_proto.h
@@ -0,0 +1,35 @@
+/*
+ * (C) Copyright 2011
+ * Helmut Raiger, HALE electronic GmbH, helmut.raiger@hale.at
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _SYS_PROTO_H_
+#define _SYS_PROTO_H_
+
+struct mxc_weimcs {
+	u32 upper;
+	u32 lower;
+	u32 additional;
+};
+
+void mxc_setup_weimcs(int cs, const struct mxc_weimcs *weimcs);
+
+#endif
diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c
index 99432ed..b9133bc 100644
--- a/board/davedenx/qong/qong.c
+++ b/board/davedenx/qong/qong.c
@@ -25,7 +25,7 @@
 #include <netdev.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
-#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
 #include <nand.h>
 #include <fsl_pmic.h>
 #include <asm/gpio.h>
@@ -61,11 +61,17 @@ static void qong_fpga_reset(void)
 int board_early_init_f (void)
 {
 #ifdef CONFIG_QONG_FPGA
-	/* CS1: FPGA/Network Controller/GPIO */
-	/* 16-bit, no DTACK */
-	__REG(CSCR_U(1)) = 0x00000A01;
-	__REG(CSCR_L(1)) = 0x20040501;
-	__REG(CSCR_A(1)) = 0x04020C00;
+	/* CS1: FPGA/Network Controller/GPIO, 16-bit, no DTACK */
+	static const struct mxc_weimcs cs1 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  0, 10, 0,  0,  1),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(2,  0,   0,   4,  0,  0,  5,  0,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   4,  0,  2,  0,  0,  3,  0,  0,  0,  0,  0,   0,  0)
+	};
+
+	mxc_setup_weimcs(1, &cs1);
 
 	/* setup pins for FPGA */
 	mx31_gpio_mux(IOMUX_MODE(0x76, MUX_CTL_GPIO));
@@ -146,50 +152,16 @@ int board_init (void)
 	/* Chip selects */
 	/* CS0: Nor Flash #0 - it must be init'ed when executing from DDR */
 	/* Assumptions: HCLK = 133 MHz, tACC = 130ns */
-	__REG(CSCR_U(0)) = ((0 << 31)	| /* SP */
-						(0 << 30)	| /* WP */
-						(0 << 28)	| /* BCD */
-						(0 << 24)	| /* BCS */
-						(0 << 22)	| /* PSZ */
-						(0 << 21)	| /* PME */
-						(0 << 20)	| /* SYNC */
-						(0 << 16)	| /* DOL */
-						(3 << 14)	| /* CNC */
-						(21 << 8)	| /* WSC */
-						(0 << 7)	| /* EW */
-						(0 << 4)	| /* WWS */
-						(6 << 0)	  /* EDC */
-					   );
-
-	__REG(CSCR_L(0)) = ((2 << 28)	| /* OEA */
-						(1 << 24)	| /* OEN */
-						(3 << 20)	| /* EBWA */
-						(3 << 16)	| /* EBWN */
-						(1 << 12)	| /* CSA */
-						(1 << 11)	| /* EBC */
-						(5 << 8)	| /* DSZ */
-						(1 << 4)	| /* CSN */
-						(0 << 3)	| /* PSR */
-						(0 << 2)	| /* CRE */
-						(0 << 1)	| /* WRAP */
-						(1 << 0)	  /* CSEN */
-					   );
-
-	__REG(CSCR_A(0)) = ((2 << 28)	| /* EBRA */
-						(1 << 24)	| /* EBRN */
-						(2 << 20)	| /* RWA */
-						(2 << 16)	| /* RWN */
-						(0 << 15)	| /* MUM */
-						(0 << 13)	| /* LAH */
-						(2 << 10)	| /* LBN */
-						(0 << 8)	| /* LBA */
-						(0 << 6)	| /* DWW */
-						(0 << 4)	| /* DCT */
-						(0 << 3)	| /* WWU */
-						(0 << 2)	| /* AGE */
-						(0 << 1)	| /* CNC2 */
-						(0 << 0)	  /* FCE */
-					   );
+	static const struct mxc_weimcs cs0 = {
+		/*     sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 21, 0,  0,  6),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(0,  1,   3,   3,  1,  1,  5,  1,  0,  0,   0,  1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   1,  2,  2,  0,  0,  2,  0,  0,  0,  0,  0,   0,  0)
+	};
+
+	mxc_setup_weimcs(0, &cs0);
 
 	/* board id for linux */
 	gd->bd->bi_arch_number = MACH_TYPE_QONG;
@@ -247,11 +219,18 @@ int board_eth_init(bd_t *bis)
 #if defined(CONFIG_QONG_FPGA) && defined(CONFIG_NAND_PLAT)
 static void board_nand_setup(void)
 {
-
 	/* CS3: NAND 8-bit */
-	__REG(CSCR_U(3)) = 0x00004f00;
-	__REG(CSCR_L(3)) = 0x20013b31;
-	__REG(CSCR_A(3)) = 0x00020800;
+	static const struct mxc_weimcs cs3 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  1, 15, 0,  0,  0),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(2,  0,   0,   1,  3,  1,  3,  3,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   0,  0,  2,  0,  0,  2,  0,  0,  0,  0,  0,  0,   0)
+	};
+
+	mxc_setup_weimcs(3, &cs3);
+
 	__REG(IOMUXC_GPR) |= 1 << 13;
 
 	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_WP, MUX_CTL_IN_GPIO));
diff --git a/board/freescale/mx31ads/mx31ads.c b/board/freescale/mx31ads/mx31ads.c
index 7637c92..6cf3a8a 100644
--- a/board/freescale/mx31ads/mx31ads.c
+++ b/board/freescale/mx31ads/mx31ads.c
@@ -22,9 +22,9 @@
 
 #include <common.h>
 #include <netdev.h>
-#include <asm/io.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -54,9 +54,16 @@ int board_early_init_f(void)
 	 * the only non-zero field "Wait State Control" is set to half the
 	 * default value.
 	 */
-	__REG(CSCR_U(0)) = 0x00000f00;
-	__REG(CSCR_L(0)) = 0x10000D03;
-	__REG(CSCR_A(0)) = 0x00720900;
+	static const struct mxc_weimcs cs0 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  0, 15, 0,  0,  0),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(1,  0,   0,   0,  0,  1,  5,  0,  0,  0,   1,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   0,  7,  2,  0,  0,  2,  1,  0,  0,  0,  0,   0,   0)
+	};
+
+	mxc_setup_weimcs(0, &cs0);
 
 	/* setup pins for UART1 */
 	mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
diff --git a/board/freescale/mx31pdk/mx31pdk.c b/board/freescale/mx31pdk/mx31pdk.c
index f6e190a..1bcf1fb 100644
--- a/board/freescale/mx31pdk/mx31pdk.c
+++ b/board/freescale/mx31pdk/mx31pdk.c
@@ -28,6 +28,7 @@
 #include <netdev.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
 #include <watchdog.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -56,9 +57,16 @@ void dram_init_banksize(void)
 int board_early_init_f(void)
 {
 	/* CS5: CPLD incl. network controller */
-	__REG(CSCR_U(5)) = 0x0000d843;
-	__REG(CSCR_L(5)) = 0x22252521;
-	__REG(CSCR_A(5)) = 0x22220a00;
+	static const struct mxc_weimcs cs5 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 24, 0,  4,  3),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(2,  2,   2,   5,  2,  0,  5,  2,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(2,   2,  2,  2,  0,  0,  2,  2,  0,  0,  0,  0,   0,  0)
+	};
+
+	mxc_setup_weimcs(5, &cs5);
 
 	/* Setup UART1 and SPI2 pins */
 	mx31_uart1_hw_init();
diff --git a/board/imx31_phycore/imx31_phycore.c b/board/imx31_phycore/imx31_phycore.c
index 773900e..a697e47 100644
--- a/board/imx31_phycore/imx31_phycore.c
+++ b/board/imx31_phycore/imx31_phycore.c
@@ -27,6 +27,7 @@
 #include <netdev.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -49,17 +50,39 @@ int board_init(void)
 
 int board_early_init_f(void)
 {
-	__REG(CSCR_U(0)) = 0x0000cf03; /* CS0: Nor Flash */
-	__REG(CSCR_L(0)) = 0x10000d03;
-	__REG(CSCR_A(0)) = 0x00720900;
+	/* CS0: Nor Flash */
+	static const struct mxc_weimcs cs0 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 15, 0,  0,  3),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(1,  0,   0,   0,  0,  1,  5,  0,  0,  0,   1,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   0,  7,  2,  0,  0,  2,  1,  0,  0,  0,  0,   0,  0)
+	};
+
+	/* CS1: Network Controller */
+	static const struct mxc_weimcs cs1 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 31, 0,  0,  6),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(4,  4,   4,  10,  4,  0,  5,  4,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(4,   4,  4,  4,  0,  1,  4,  3,  0,  0,  0,  0,   1,  0)
+	};
 
-	__REG(CSCR_U(1)) = 0x0000df06; /* CS1: Network Controller */
-	__REG(CSCR_L(1)) = 0x444a4541;
-	__REG(CSCR_A(1)) = 0x44443302;
+	/* CS4: SRAM */
+	static const struct mxc_weimcs cs4 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 24, 0,  4,  3),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(2,  2,   2,   5,  2,  0,  5,  2,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(2,   2,  2,  2,  0,  0,  2,  2,  0,  0,  0,  0,   0,  0)
+	};
 
-	__REG(CSCR_U(4)) = 0x0000d843; /* CS4: SRAM */
-	__REG(CSCR_L(4)) = 0x22252521;
-	__REG(CSCR_A(4)) = 0x22220a00;
+	mxc_setup_weimcs(0, &cs0);
+	mxc_setup_weimcs(1, &cs1);
+	mxc_setup_weimcs(4, &cs4);
 
 	/* setup pins for UART1 */
 	mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
diff --git a/board/logicpd/imx31_litekit/imx31_litekit.c b/board/logicpd/imx31_litekit/imx31_litekit.c
index 09cc9c5..0615215 100644
--- a/board/logicpd/imx31_litekit/imx31_litekit.c
+++ b/board/logicpd/imx31_litekit/imx31_litekit.c
@@ -26,6 +26,7 @@
 #include <netdev.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -45,13 +46,28 @@ void dram_init_banksize(void)
 
 int board_early_init_f(void)
 {
-	__REG(CSCR_U(0)) = 0x0000cf03; /* CS0: Nor Flash */
-	__REG(CSCR_L(0)) = 0xa0330d01;
-	__REG(CSCR_A(0)) = 0x00220800;
+	/* CS0: Nor Flash */
+	static const struct mxc_weimcs cs0 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 15, 0,  0,  3),
+		/*    oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(10,  0,   3,   3,  0,  1,  5,  0,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   0,  2,  2,  0,  0,  2,  0,  0,  0,  0,  0,   0,  0)
+	};
 
-	__REG(CSCR_U(4)) = 0x0000dcf6; /* CS4: Network Controller */
-	__REG(CSCR_L(4)) = 0x444a4541;
-	__REG(CSCR_A(4)) = 0x44443302;
+	/* CS4: Network Controller */
+	static const struct mxc_weimcs cs4 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 28, 1,  7,  6),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(4,  4,   4,  10,  4,  0,  5,  4,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(4,   4,  4,  4,  0,  1,  4,  3,  0,  0,  0,  0,   1,  0)
+	};
+
+	mxc_setup_weimcs(0, &cs0);
+	mxc_setup_weimcs(4, &cs4);
 
 	/* setup pins for UART1 */
 	mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
-- 
1.7.4.4



--
Scanned by MailScanner.