* [PATCH 00/18] MIPS: Alchemy board and driver updates
@ 2011-11-01 19:03 Manuel Lauss
2011-11-01 19:03 ` [PATCH 01/18] MIPS: Alchemy: remove PB1000 support Manuel Lauss
` (17 more replies)
0 siblings, 18 replies; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Here's a collection of patches to the Alchemy board and driver codebases I've
been sitting on a while.
All apply against latest linus-git (as of 2011-11-01 1800Z) merged with Ralf's
upstream-linus branch.
Overview:
#01-02 get rid of unused board code (PB1000, Bosporus/Mirage). I have no test
hardware; getting rid of Bosporus/Mirage makes it much easier to merge
support for DB1000/1500/1100. I have datasheets for all three and can
bring them back if desired, but I'd rather not if at all possible.
#03 db1200 irq code optimization
#04-05 Au1300/Db1300 support
#06 better db1550 support, like db1200 and db1300.
#07-08 board support code is (imo needlessly) scattered across multiple files.
these patches merge them into per-board files.
#09 au1200fb calls globally-visible functions to control panels. this patch
introduces platform data instead, because it's much nicer.
#10 pb1200 is just a db1200 with more mmc and camera sockets. this patch
implements board autodetection and setup for both to the db1200 code.
#11 db1000/1500/1100 are basically identical (plus PCI for db1500). after
applying this patch a kernel image can be built which runs on all three.
#12 add MMC support to the DB1100
#13 add the on-chip RTC device to all pb/db boards.
#14 convert au1550nd.c to a platform driver. I initially did this because
gen_nand didn't seem to work on the DB1550 until I realized YAMON did
not configure the NAND CS correctly (the original writers realized that
and had au1550nd.c correct that). After a YAMON update gen_nand works
for the DB1550, but since I have no PB1550 I opted to keep au1550nd.
#15 with the au1550nd.c conversion some headers have become obsolete.
#16 convert au1k_ir IRDA driver to platform_driver.
#17 add IrDA platform data for DB1000/1100 (necessary after #16).
#18 add ADS78xx touchscreen support to DB1100.
All compile and run-tested where possible.
Thanks,
Manuel Lauss
Manuel Lauss (18):
MIPS: Alchemy: remove PB1000 support
MIPS: Alchemy: drop MIRAGE/BOSPORUS board support
MIPS: Alchemy: devboards: remove unneeded BCSR IRQ register writes
MIPS: Alchemy: Au1300 SoC support
MIPS: Alchemy: DB1300 support
MIPS: Alchemy: better DB1550 support
MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files
MIPS: Alchemy: merge devboard code into single per-board files.
MIPS: Alchemy: move au1200fb global functions to platform data
MIPS: Alchemy: Merge PB1200 support into DB1200 code.
MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100
MIPS: Alchemy: MMC for DB1100
MIPS: Alchemy: add RTC device to all devboards
MTD: nand: make au1550nd.c a platform_driver
MIPS: Alchemy: remove unused board headers
net/irda: convert au1k_ir to platform driver.
MIPS: Alchemy: hook up IrDA on DB1000/DB1100
MIPS: Alchemy: Touchscreen support on DB1100
arch/mips/alchemy/Kconfig | 60 +-
arch/mips/alchemy/Makefile | 3 +
arch/mips/alchemy/Platform | 58 +-
arch/mips/alchemy/board-gpr.c | 303 ++++++
arch/mips/alchemy/board-mtx1.c | 313 ++++++
arch/mips/alchemy/board-xxs1500.c | 154 +++
arch/mips/alchemy/common/Makefile | 3 +-
arch/mips/alchemy/common/dbdma.c | 46 +
arch/mips/alchemy/common/gpioint.c | 411 ++++++++
arch/mips/alchemy/common/gpiolib.c | 42 +
arch/mips/alchemy/common/irq.c | 11 -
arch/mips/alchemy/common/platform.c | 31 +-
arch/mips/alchemy/common/power.c | 3 +
arch/mips/alchemy/common/sleeper.S | 73 ++
arch/mips/alchemy/common/time.c | 1 +
arch/mips/alchemy/common/vss.c | 84 ++
arch/mips/alchemy/devboards/Makefile | 19 +-
arch/mips/alchemy/devboards/bcsr.c | 11 +-
arch/mips/alchemy/devboards/db1000.c | 564 ++++++++++
arch/mips/alchemy/devboards/db1200.c | 913 ++++++++++++++++
arch/mips/alchemy/devboards/db1200/Makefile | 1 -
arch/mips/alchemy/devboards/db1200/platform.c | 648 ------------
arch/mips/alchemy/devboards/db1200/setup.c | 81 --
arch/mips/alchemy/devboards/db1300.c | 784 ++++++++++++++
arch/mips/alchemy/devboards/db1550.c | 498 +++++++++
arch/mips/alchemy/devboards/db1x00/Makefile | 8 -
arch/mips/alchemy/devboards/db1x00/board_setup.c | 229 ----
arch/mips/alchemy/devboards/db1x00/platform.c | 315 ------
arch/mips/alchemy/devboards/pb1000/Makefile | 8 -
arch/mips/alchemy/devboards/pb1000/board_setup.c | 209 ----
arch/mips/alchemy/devboards/pb1100.c | 167 +++
arch/mips/alchemy/devboards/pb1100/Makefile | 8 -
arch/mips/alchemy/devboards/pb1100/board_setup.c | 127 ---
arch/mips/alchemy/devboards/pb1100/platform.c | 77 --
arch/mips/alchemy/devboards/pb1200/Makefile | 5 -
arch/mips/alchemy/devboards/pb1200/board_setup.c | 174 ---
arch/mips/alchemy/devboards/pb1200/platform.c | 339 ------
arch/mips/alchemy/devboards/pb1500.c | 198 ++++
arch/mips/alchemy/devboards/pb1500/Makefile | 8 -
arch/mips/alchemy/devboards/pb1500/board_setup.c | 139 ---
arch/mips/alchemy/devboards/pb1500/platform.c | 94 --
arch/mips/alchemy/devboards/pb1550.c | 244 +++++
arch/mips/alchemy/devboards/pb1550/Makefile | 8 -
arch/mips/alchemy/devboards/pb1550/board_setup.c | 80 --
arch/mips/alchemy/devboards/pb1550/platform.c | 140 ---
arch/mips/alchemy/devboards/platform.c | 13 +-
arch/mips/alchemy/devboards/prom.c | 11 +-
arch/mips/alchemy/gpr/Makefile | 8 -
arch/mips/alchemy/gpr/board_setup.c | 75 --
arch/mips/alchemy/gpr/init.c | 63 --
arch/mips/alchemy/gpr/platform.c | 230 ----
arch/mips/alchemy/mtx-1/Makefile | 9 -
arch/mips/alchemy/mtx-1/board_setup.c | 94 --
arch/mips/alchemy/mtx-1/init.c | 66 --
arch/mips/alchemy/mtx-1/platform.c | 230 ----
arch/mips/alchemy/xxs1500/Makefile | 8 -
arch/mips/alchemy/xxs1500/board_setup.c | 93 --
arch/mips/alchemy/xxs1500/init.c | 63 --
arch/mips/alchemy/xxs1500/platform.c | 63 --
arch/mips/boot/compressed/uart-alchemy.c | 5 +-
arch/mips/configs/db1000_defconfig | 369 ++++++--
arch/mips/configs/db1100_defconfig | 122 ---
arch/mips/configs/db1300_defconfig | 391 +++++++
arch/mips/configs/db1500_defconfig | 128 ---
arch/mips/configs/db1550_defconfig | 288 ++++--
arch/mips/configs/pb1200_defconfig | 170 ---
arch/mips/include/asm/cpu.h | 1 +
arch/mips/include/asm/mach-au1x00/au1000.h | 273 ++++-
arch/mips/include/asm/mach-au1x00/au1100_mmc.h | 2 +
arch/mips/include/asm/mach-au1x00/au1200fb.h | 14 +
arch/mips/include/asm/mach-au1x00/au1550nd.h | 16 +
arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h | 31 +
arch/mips/include/asm/mach-au1x00/gpio-au1300.h | 241 +++++
arch/mips/include/asm/mach-au1x00/gpio.h | 3 +
arch/mips/include/asm/mach-db1x00/bcsr.h | 36 +-
arch/mips/include/asm/mach-db1x00/db1200.h | 11 +-
arch/mips/include/asm/mach-db1x00/db1300.h | 40 +
arch/mips/include/asm/mach-db1x00/db1x00.h | 79 --
arch/mips/include/asm/mach-db1x00/irq.h | 23 +
arch/mips/include/asm/mach-pb1x00/mc146818rtc.h | 34 -
arch/mips/include/asm/mach-pb1x00/pb1000.h | 87 --
arch/mips/include/asm/mach-pb1x00/pb1200.h | 139 ---
arch/mips/include/asm/mach-pb1x00/pb1550.h | 73 --
arch/mips/kernel/cpu-probe.c | 7 +
drivers/i2c/busses/Kconfig | 4 +-
drivers/mmc/host/au1xmmc.c | 45 +-
drivers/mtd/nand/au1550nd.c | 308 +++---
drivers/net/irda/Kconfig | 6 +-
drivers/net/irda/au1000_ircc.h | 125 ---
drivers/net/irda/au1k_ir.c | 1229 ++++++++++++----------
drivers/pcmcia/Kconfig | 8 +-
drivers/pcmcia/Makefile | 4 -
drivers/pcmcia/au1000_generic.c | 545 ----------
drivers/pcmcia/au1000_generic.h | 135 ---
drivers/pcmcia/au1000_pb1x00.c | 294 ------
drivers/pcmcia/db1xxx_ss.c | 26 +-
drivers/spi/Kconfig | 4 +-
drivers/usb/host/alchemy-common.c | 277 +++++
drivers/usb/host/ohci-au1xxx.c | 13 +-
drivers/video/Kconfig | 8 +-
drivers/video/au1100fb.c | 12 -
drivers/video/au1200fb.c | 273 +++---
sound/soc/au1x/Kconfig | 16 +-
sound/soc/au1x/db1200.c | 73 ++-
104 files changed, 7817 insertions(+), 6889 deletions(-)
create mode 100644 arch/mips/alchemy/Makefile
create mode 100644 arch/mips/alchemy/board-gpr.c
create mode 100644 arch/mips/alchemy/board-mtx1.c
create mode 100644 arch/mips/alchemy/board-xxs1500.c
create mode 100644 arch/mips/alchemy/common/gpioint.c
create mode 100644 arch/mips/alchemy/common/vss.c
create mode 100644 arch/mips/alchemy/devboards/db1000.c
create mode 100644 arch/mips/alchemy/devboards/db1200.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1200/platform.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/setup.c
create mode 100644 arch/mips/alchemy/devboards/db1300.c
create mode 100644 arch/mips/alchemy/devboards/db1550.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1x00/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/platform.c
delete mode 100644 arch/mips/alchemy/devboards/pb1000/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1000/board_setup.c
create mode 100644 arch/mips/alchemy/devboards/pb1100.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1100/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/platform.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1200/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1500.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1500/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1550.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1550/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/platform.c
delete mode 100644 arch/mips/alchemy/gpr/Makefile
delete mode 100644 arch/mips/alchemy/gpr/board_setup.c
delete mode 100644 arch/mips/alchemy/gpr/init.c
delete mode 100644 arch/mips/alchemy/gpr/platform.c
delete mode 100644 arch/mips/alchemy/mtx-1/Makefile
delete mode 100644 arch/mips/alchemy/mtx-1/board_setup.c
delete mode 100644 arch/mips/alchemy/mtx-1/init.c
delete mode 100644 arch/mips/alchemy/mtx-1/platform.c
delete mode 100644 arch/mips/alchemy/xxs1500/Makefile
delete mode 100644 arch/mips/alchemy/xxs1500/board_setup.c
delete mode 100644 arch/mips/alchemy/xxs1500/init.c
delete mode 100644 arch/mips/alchemy/xxs1500/platform.c
delete mode 100644 arch/mips/configs/db1100_defconfig
create mode 100644 arch/mips/configs/db1300_defconfig
delete mode 100644 arch/mips/configs/db1500_defconfig
delete mode 100644 arch/mips/configs/pb1200_defconfig
create mode 100644 arch/mips/include/asm/mach-au1x00/au1200fb.h
create mode 100644 arch/mips/include/asm/mach-au1x00/au1550nd.h
create mode 100644 arch/mips/include/asm/mach-au1x00/gpio-au1300.h
create mode 100644 arch/mips/include/asm/mach-db1x00/db1300.h
delete mode 100644 arch/mips/include/asm/mach-db1x00/db1x00.h
create mode 100644 arch/mips/include/asm/mach-db1x00/irq.h
delete mode 100644 arch/mips/include/asm/mach-pb1x00/mc146818rtc.h
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1000.h
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1200.h
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1550.h
delete mode 100644 drivers/net/irda/au1000_ircc.h
delete mode 100644 drivers/pcmcia/au1000_generic.c
delete mode 100644 drivers/pcmcia/au1000_generic.h
delete mode 100644 drivers/pcmcia/au1000_pb1x00.c
--
1.7.7.1
^ permalink raw reply [flat|nested] 46+ messages in thread
* [PATCH 01/18] MIPS: Alchemy: remove PB1000 support
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-02 11:37 ` Ralf Baechle
2011-11-02 11:53 ` [PATCH RESEND " Manuel Lauss
2011-11-01 19:03 ` [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support Manuel Lauss
` (16 subsequent siblings)
17 siblings, 2 replies; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Noone seems to have test hardware or care anymore. Drop PB1000 support
and along with it the old Alchemy PCMCIA socket driver.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Kconfig | 9 -
arch/mips/alchemy/Platform | 7 -
arch/mips/alchemy/common/irq.c | 11 -
arch/mips/alchemy/devboards/Makefile | 1 -
arch/mips/alchemy/devboards/pb1000/Makefile | 8 -
arch/mips/alchemy/devboards/pb1000/board_setup.c | 209 ---------
arch/mips/alchemy/devboards/prom.c | 2 +-
arch/mips/include/asm/mach-pb1x00/pb1000.h | 87 ----
drivers/net/irda/au1k_ir.c | 5 +-
drivers/pcmcia/Kconfig | 4 -
drivers/pcmcia/Makefile | 4 -
drivers/pcmcia/au1000_generic.c | 545 ----------------------
drivers/pcmcia/au1000_generic.h | 135 ------
drivers/pcmcia/au1000_pb1x00.c | 294 ------------
14 files changed, 2 insertions(+), 1319 deletions(-)
delete mode 100644 arch/mips/alchemy/devboards/pb1000/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1000/board_setup.c
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1000.h
delete mode 100644 drivers/pcmcia/au1000_generic.c
delete mode 100644 drivers/pcmcia/au1000_generic.h
delete mode 100644 drivers/pcmcia/au1000_pb1x00.c
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 2a68be6..5a48387 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -78,15 +78,6 @@ config MIPS_MIRAGE
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_PB1000
- bool "Alchemy PB1000 board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select SWAP_IO_SPACE
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_PB1100
bool "Alchemy PB1100 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 96e9e41..4e07967 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -5,13 +5,6 @@ platform-$(CONFIG_MIPS_ALCHEMY) += alchemy/common/
#
-# AMD Alchemy Pb1000 eval board
-#
-platform-$(CONFIG_MIPS_PB1000) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1000) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
-load-$(CONFIG_MIPS_PB1000) += 0xffffffff80100000
-
-#
# AMD Alchemy Pb1100 eval board
#
platform-$(CONFIG_MIPS_PB1100) += alchemy/devboards/
diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index 8b60ba0..2a94a64 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -35,9 +35,6 @@
#include <asm/irq_cpu.h>
#include <asm/mipsregs.h>
#include <asm/mach-au1x00/au1000.h>
-#ifdef CONFIG_MIPS_PB1000
-#include <asm/mach-pb1x00/pb1000.h>
-#endif
/* Interrupt Controller register offsets */
#define IC_CFG0RD 0x40
@@ -265,14 +262,6 @@ static void au1x_ic1_unmask(struct irq_data *d)
__raw_writel(1 << bit, base + IC_MASKSET);
__raw_writel(1 << bit, base + IC_WAKESET);
-
-/* very hacky. does the pb1000 cpld auto-disable this int?
- * nowhere in the current kernel sources is it disabled. --mlau
- */
-#if defined(CONFIG_MIPS_PB1000)
- if (d->irq == AU1000_GPIO15_INT)
- __raw_writel(0x4000, (void __iomem *)PB1000_MDR); /* enable int */
-#endif
wmb();
}
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 826449c..bea80d7 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -4,7 +4,6 @@
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_MIPS_PB1000) += pb1000/
obj-$(CONFIG_MIPS_PB1100) += pb1100/
obj-$(CONFIG_MIPS_PB1200) += pb1200/
obj-$(CONFIG_MIPS_PB1500) += pb1500/
diff --git a/arch/mips/alchemy/devboards/pb1000/Makefile b/arch/mips/alchemy/devboards/pb1000/Makefile
deleted file mode 100644
index 97c6615..0000000
--- a/arch/mips/alchemy/devboards/pb1000/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1000 board.
-#
-
-obj-y := board_setup.o
diff --git a/arch/mips/alchemy/devboards/pb1000/board_setup.c b/arch/mips/alchemy/devboards/pb1000/board_setup.c
deleted file mode 100644
index e64fdcb..0000000
--- a/arch/mips/alchemy/devboards/pb1000/board_setup.c
+++ /dev/null
@@ -1,209 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1000.h>
-#include <asm/reboot.h>
-#include <prom.h>
-
-#include "../platform.h"
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1000";
-}
-
-static void board_reset(char *c)
-{
- asm volatile ("jr %0" : : "r" (0xbfc00000));
-}
-
-static void board_power_off(void)
-{
- while (1)
- asm volatile (
- " .set mips32 \n"
- " wait \n"
- " .set mips0 \n");
-}
-
-void __init board_setup(void)
-{
- u32 pin_func, static_cfg0;
- u32 sys_freqctrl, sys_clksrc;
- u32 prid = read_c0_prid();
-
- sys_freqctrl = 0;
- sys_clksrc = 0;
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- /* CPU core freq to 48 MHz to slow it way down... */
- au_writel(4, SYS_CPUPLL);
-
- /*
- * Setup 48 MHz FREQ2 from CPUPLL for USB Host
- * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
- */
- sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* CPU core freq to 384 MHz */
- au_writel(0x20, SYS_CPUPLL);
-
- printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
- break;
-
- default: /* HC and newer */
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
- break;
- }
-
- /*
- * Route 48 MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
-
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
-
- au_writel(pin_func, SYS_PINFUNC);
-
- alchemy_gpio_direction_input(11);
- alchemy_gpio_direction_input(13);
- alchemy_gpio_direction_output(4, 0);
- alchemy_gpio_direction_output(5, 0);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Make GPIO 15 an input (for interrupt line) */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
- /* We don't need I2S, so make it available for GPIO[31:29] */
- pin_func |= SYS_PF_I2S;
- au_writel(pin_func, SYS_PINFUNC);
-
- alchemy_gpio_direction_input(15);
-
- static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
- au_writel(static_cfg0, MEM_STCFG0);
-
- /* configure RCE2* for LCD */
- au_writel(0x00000004, MEM_STCFG2);
-
- /* MEM_STTIME2 */
- au_writel(0x09000000, MEM_STTIME2);
-
- /* Set 32-bit base address decoding for RCE2* */
- au_writel(0x10003ff0, MEM_STADDR2);
-
- /*
- * PCI CPLD setup
- * Expand CE0 to cover PCI
- */
- au_writel(0x11803e40, MEM_STADDR1);
-
- /* Burst visibility on */
- au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
-
- au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */
- au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Enable Au1000 BCLK switching - note: sed1356 must not use
- * its BCLK (Au1000 LCLK) for any timings
- */
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- break;
- default: /* HC and newer */
- /*
- * Enable sys bus clock divider when IDLE state or no bus
- * activity.
- */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
- break;
- }
-
- pm_power_off = board_power_off;
- _machine_halt = board_power_off;
- _machine_restart = board_reset;
-}
-
-static int __init pb1000_init_irq(void)
-{
- irq_set_irq_type(AU1000_GPIO15_INT, IRQF_TRIGGER_LOW);
- return 0;
-}
-arch_initcall(pb1000_init_irq);
-
-static int __init pb1000_device_init(void)
-{
- return db1x_register_norflash(8 * 1024 * 1024, 4, 0);
-}
-device_initcall(pb1000_device_init);
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index e5306b5..56d7ea5 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -33,7 +33,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_DB1000) || \
+#if defined(CONFIG_MIPS_DB1000) || \
defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500) || \
defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
diff --git a/arch/mips/include/asm/mach-pb1x00/pb1000.h b/arch/mips/include/asm/mach-pb1x00/pb1000.h
deleted file mode 100644
index 6505925..0000000
--- a/arch/mips/include/asm/mach-pb1x00/pb1000.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * Alchemy Semi Pb1000 Reference Board
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#ifndef __ASM_PB1000_H
-#define __ASM_PB1000_H
-
-/* PCMCIA PB1000 specific defines */
-#define PCMCIA_MAX_SOCK 1
-#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK + 1)
-
-#define PB1000_PCR 0xBE000000
-# define PCR_SLOT_0_VPP0 (1 << 0)
-# define PCR_SLOT_0_VPP1 (1 << 1)
-# define PCR_SLOT_0_VCC0 (1 << 2)
-# define PCR_SLOT_0_VCC1 (1 << 3)
-# define PCR_SLOT_0_RST (1 << 4)
-# define PCR_SLOT_1_VPP0 (1 << 8)
-# define PCR_SLOT_1_VPP1 (1 << 9)
-# define PCR_SLOT_1_VCC0 (1 << 10)
-# define PCR_SLOT_1_VCC1 (1 << 11)
-# define PCR_SLOT_1_RST (1 << 12)
-
-#define PB1000_MDR 0xBE000004
-# define MDR_PI (1 << 5) /* PCMCIA int latch */
-# define MDR_EPI (1 << 14) /* enable PCMCIA int */
-# define MDR_CPI (1 << 15) /* clear PCMCIA int */
-
-#define PB1000_ACR1 0xBE000008
-# define ACR1_SLOT_0_CD1 (1 << 0) /* card detect 1 */
-# define ACR1_SLOT_0_CD2 (1 << 1) /* card detect 2 */
-# define ACR1_SLOT_0_READY (1 << 2) /* ready */
-# define ACR1_SLOT_0_STATUS (1 << 3) /* status change */
-# define ACR1_SLOT_0_VS1 (1 << 4) /* voltage sense 1 */
-# define ACR1_SLOT_0_VS2 (1 << 5) /* voltage sense 2 */
-# define ACR1_SLOT_0_INPACK (1 << 6) /* inpack pin status */
-# define ACR1_SLOT_1_CD1 (1 << 8) /* card detect 1 */
-# define ACR1_SLOT_1_CD2 (1 << 9) /* card detect 2 */
-# define ACR1_SLOT_1_READY (1 << 10) /* ready */
-# define ACR1_SLOT_1_STATUS (1 << 11) /* status change */
-# define ACR1_SLOT_1_VS1 (1 << 12) /* voltage sense 1 */
-# define ACR1_SLOT_1_VS2 (1 << 13) /* voltage sense 2 */
-# define ACR1_SLOT_1_INPACK (1 << 14) /* inpack pin status */
-
-#define CPLD_AUX0 0xBE00000C
-#define CPLD_AUX1 0xBE000010
-#define CPLD_AUX2 0xBE000014
-
-/* Voltage levels */
-
-/* VPPEN1 - VPPEN0 */
-#define VPP_GND ((0 << 1) | (0 << 0))
-#define VPP_5V ((1 << 1) | (0 << 0))
-#define VPP_3V ((0 << 1) | (1 << 0))
-#define VPP_12V ((0 << 1) | (1 << 0))
-#define VPP_HIZ ((1 << 1) | (1 << 0))
-
-/* VCCEN1 - VCCEN0 */
-#define VCC_3V ((0 << 1) | (1 << 0))
-#define VCC_5V ((1 << 1) | (0 << 0))
-#define VCC_HIZ ((0 << 1) | (0 << 0))
-
-/* VPP/VCC */
-#define SET_VCC_VPP(VCC, VPP, SLOT) \
- ((((VCC) << 2) | ((VPP) << 0)) << ((SLOT) * 8))
-#endif /* __ASM_PB1000_H */
diff --git a/drivers/net/irda/au1k_ir.c b/drivers/net/irda/au1k_ir.c
index a3d696a..d1a77ef 100644
--- a/drivers/net/irda/au1k_ir.c
+++ b/drivers/net/irda/au1k_ir.c
@@ -32,10 +32,7 @@
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/au1000.h>
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_PB1100)
-#include <asm/pb1000.h>
-#elif defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
-#include <asm/db1x00.h>
+#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
#include <asm/mach-db1x00/bcsr.h>
#else
#error au1k_ir: unsupported board
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 6e318ce..c022b5c 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -155,10 +155,6 @@ config PCMCIA_M8XX
This driver is also available as a module called m8xx_pcmcia.
-config PCMCIA_AU1X00
- tristate "Au1x00 pcmcia support"
- depends on MIPS_ALCHEMY && PCMCIA
-
config PCMCIA_ALCHEMY_DEVBOARD
tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
depends on MIPS_ALCHEMY && PCMCIA
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 29935ea..ec543a4 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_PCMCIA_SA1100) += sa11xx_base.o sa1100_cs.o
obj-$(CONFIG_PCMCIA_SA1111) += sa11xx_base.o sa1111_cs.o
obj-$(CONFIG_M32R_PCC) += m32r_pcc.o
obj-$(CONFIG_M32R_CFC) += m32r_cfc.o
-obj-$(CONFIG_PCMCIA_AU1X00) += au1x00_ss.o
obj-$(CONFIG_PCMCIA_BCM63XX) += bcm63xx_pcmcia.o
obj-$(CONFIG_PCMCIA_VRC4171) += vrc4171_card.o
obj-$(CONFIG_PCMCIA_VRC4173) += vrc4173_cardu.o
@@ -39,9 +38,6 @@ obj-$(CONFIG_AT91_CF) += at91_cf.o
obj-$(CONFIG_ELECTRA_CF) += electra_cf.o
obj-$(CONFIG_PCMCIA_ALCHEMY_DEVBOARD) += db1xxx_ss.o
-au1x00_ss-y += au1000_generic.o
-au1x00_ss-$(CONFIG_MIPS_PB1000) += au1000_pb1x00.o
-
sa1111_cs-y += sa1111_generic.o
sa1111_cs-$(CONFIG_ASSABET_NEPONSET) += sa1100_neponset.o
sa1111_cs-$(CONFIG_SA1100_BADGE4) += sa1100_badge4.o
diff --git a/drivers/pcmcia/au1000_generic.c b/drivers/pcmcia/au1000_generic.c
deleted file mode 100644
index 95dd7c6..0000000
--- a/drivers/pcmcia/au1000_generic.c
+++ /dev/null
@@ -1,545 +0,0 @@
-/*
- *
- * Alchemy Semi Au1000 pcmcia driver
- *
- * Copyright 2001-2003 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@embeddedalley.com or source@mvista.com
- *
- * Copyright 2004 Pete Popov, Embedded Alley Solutions, Inc.
- * Updated the driver to 2.6. Followed the sa11xx API and largely
- * copied many of the hardware independent functions.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/cpufreq.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/notifier.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include "au1000_generic.h"
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Pete Popov <ppopov@embeddedalley.com>");
-MODULE_DESCRIPTION("Linux PCMCIA Card Services: Au1x00 Socket Controller");
-
-#if 0
-#define debug(x,args...) printk(KERN_DEBUG "%s: " x, __func__ , ##args)
-#else
-#define debug(x,args...)
-#endif
-
-#define MAP_SIZE 0x100000
-extern struct au1000_pcmcia_socket au1000_pcmcia_socket[];
-#define PCMCIA_SOCKET(x) (au1000_pcmcia_socket + (x))
-#define to_au1000_socket(x) container_of(x, struct au1000_pcmcia_socket, socket)
-
-/* Some boards like to support CF cards as IDE root devices, so they
- * grab pcmcia sockets directly.
- */
-u32 *pcmcia_base_vaddrs[2];
-extern const unsigned long mips_io_port_base;
-
-static DEFINE_MUTEX(pcmcia_sockets_lock);
-
-static int (*au1x00_pcmcia_hw_init[])(struct device *dev) = {
- au1x_board_init,
-};
-
-static int
-au1x00_pcmcia_skt_state(struct au1000_pcmcia_socket *skt)
-{
- struct pcmcia_state state;
- unsigned int stat;
-
- memset(&state, 0, sizeof(struct pcmcia_state));
-
- skt->ops->socket_state(skt, &state);
-
- stat = state.detect ? SS_DETECT : 0;
- stat |= state.ready ? SS_READY : 0;
- stat |= state.wrprot ? SS_WRPROT : 0;
- stat |= state.vs_3v ? SS_3VCARD : 0;
- stat |= state.vs_Xv ? SS_XVCARD : 0;
- stat |= skt->cs_state.Vcc ? SS_POWERON : 0;
-
- if (skt->cs_state.flags & SS_IOCARD)
- stat |= state.bvd1 ? SS_STSCHG : 0;
- else {
- if (state.bvd1 == 0)
- stat |= SS_BATDEAD;
- else if (state.bvd2 == 0)
- stat |= SS_BATWARN;
- }
- return stat;
-}
-
-/*
- * au100_pcmcia_config_skt
- *
- * Convert PCMCIA socket state to our socket configure structure.
- */
-static int
-au1x00_pcmcia_config_skt(struct au1000_pcmcia_socket *skt, socket_state_t *state)
-{
- int ret;
-
- ret = skt->ops->configure_socket(skt, state);
- if (ret == 0) {
- skt->cs_state = *state;
- }
-
- if (ret < 0)
- debug("unable to configure socket %d\n", skt->nr);
-
- return ret;
-}
-
-/* au1x00_pcmcia_sock_init()
- *
- * (Re-)Initialise the socket, turning on status interrupts
- * and PCMCIA bus. This must wait for power to stabilise
- * so that the card status signals report correctly.
- *
- * Returns: 0
- */
-static int au1x00_pcmcia_sock_init(struct pcmcia_socket *sock)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("initializing socket %u\n", skt->nr);
-
- skt->ops->socket_init(skt);
- return 0;
-}
-
-/*
- * au1x00_pcmcia_suspend()
- *
- * Remove power on the socket, disable IRQs from the card.
- * Turn off status interrupts, and disable the PCMCIA bus.
- *
- * Returns: 0
- */
-static int au1x00_pcmcia_suspend(struct pcmcia_socket *sock)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("suspending socket %u\n", skt->nr);
-
- skt->ops->socket_suspend(skt);
-
- return 0;
-}
-
-static DEFINE_SPINLOCK(status_lock);
-
-/*
- * au1x00_check_status()
- */
-static void au1x00_check_status(struct au1000_pcmcia_socket *skt)
-{
- unsigned int events;
-
- debug("entering PCMCIA monitoring thread\n");
-
- do {
- unsigned int status;
- unsigned long flags;
-
- status = au1x00_pcmcia_skt_state(skt);
-
- spin_lock_irqsave(&status_lock, flags);
- events = (status ^ skt->status) & skt->cs_state.csc_mask;
- skt->status = status;
- spin_unlock_irqrestore(&status_lock, flags);
-
- debug("events: %s%s%s%s%s%s\n",
- events == 0 ? "<NONE>" : "",
- events & SS_DETECT ? "DETECT " : "",
- events & SS_READY ? "READY " : "",
- events & SS_BATDEAD ? "BATDEAD " : "",
- events & SS_BATWARN ? "BATWARN " : "",
- events & SS_STSCHG ? "STSCHG " : "");
-
- if (events)
- pcmcia_parse_events(&skt->socket, events);
- } while (events);
-}
-
-/*
- * au1x00_pcmcia_poll_event()
- * Let's poll for events in addition to IRQs since IRQ only is unreliable...
- */
-static void au1x00_pcmcia_poll_event(unsigned long dummy)
-{
- struct au1000_pcmcia_socket *skt = (struct au1000_pcmcia_socket *)dummy;
- debug("polling for events\n");
-
- mod_timer(&skt->poll_timer, jiffies + AU1000_PCMCIA_POLL_PERIOD);
-
- au1x00_check_status(skt);
-}
-
-/* au1x00_pcmcia_get_status()
- *
- * From the sa11xx_core.c:
- * Implements the get_status() operation for the in-kernel PCMCIA
- * service (formerly SS_GetStatus in Card Services). Essentially just
- * fills in bits in `status' according to internal driver state or
- * the value of the voltage detect chipselect register.
- *
- * As a debugging note, during card startup, the PCMCIA core issues
- * three set_socket() commands in a row the first with RESET deasserted,
- * the second with RESET asserted, and the last with RESET deasserted
- * again. Following the third set_socket(), a get_status() command will
- * be issued. The kernel is looking for the SS_READY flag (see
- * setup_socket(), reset_socket(), and unreset_socket() in cs.c).
- *
- * Returns: 0
- */
-static int
-au1x00_pcmcia_get_status(struct pcmcia_socket *sock, unsigned int *status)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- skt->status = au1x00_pcmcia_skt_state(skt);
- *status = skt->status;
-
- return 0;
-}
-
-/* au1x00_pcmcia_set_socket()
- * Implements the set_socket() operation for the in-kernel PCMCIA
- * service (formerly SS_SetSocket in Card Services). We more or
- * less punt all of this work and let the kernel handle the details
- * of power configuration, reset, &c. We also record the value of
- * `state' in order to regurgitate it to the PCMCIA core later.
- *
- * Returns: 0
- */
-static int
-au1x00_pcmcia_set_socket(struct pcmcia_socket *sock, socket_state_t *state)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("for sock %u\n", skt->nr);
-
- debug("\tmask: %s%s%s%s%s%s\n\tflags: %s%s%s%s%s%s\n",
- (state->csc_mask==0)?"<NONE>":"",
- (state->csc_mask&SS_DETECT)?"DETECT ":"",
- (state->csc_mask&SS_READY)?"READY ":"",
- (state->csc_mask&SS_BATDEAD)?"BATDEAD ":"",
- (state->csc_mask&SS_BATWARN)?"BATWARN ":"",
- (state->csc_mask&SS_STSCHG)?"STSCHG ":"",
- (state->flags==0)?"<NONE>":"",
- (state->flags&SS_PWR_AUTO)?"PWR_AUTO ":"",
- (state->flags&SS_IOCARD)?"IOCARD ":"",
- (state->flags&SS_RESET)?"RESET ":"",
- (state->flags&SS_SPKR_ENA)?"SPKR_ENA ":"",
- (state->flags&SS_OUTPUT_ENA)?"OUTPUT_ENA ":"");
- debug("\tVcc %d Vpp %d irq %d\n",
- state->Vcc, state->Vpp, state->io_irq);
-
- return au1x00_pcmcia_config_skt(skt, state);
-}
-
-int
-au1x00_pcmcia_set_io_map(struct pcmcia_socket *sock, struct pccard_io_map *map)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
- unsigned int speed;
-
- if(map->map>=MAX_IO_WIN){
- debug("map (%d) out of range\n", map->map);
- return -1;
- }
-
- if(map->flags&MAP_ACTIVE){
- speed=(map->speed>0)?map->speed:AU1000_PCMCIA_IO_SPEED;
- skt->spd_io[map->map] = speed;
- }
-
- map->start=(unsigned int)(u32)skt->virt_io;
- map->stop=map->start+MAP_SIZE;
- return 0;
-
-} /* au1x00_pcmcia_set_io_map() */
-
-
-static int
-au1x00_pcmcia_set_mem_map(struct pcmcia_socket *sock, struct pccard_mem_map *map)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
- unsigned short speed = map->speed;
-
- if(map->map>=MAX_WIN){
- debug("map (%d) out of range\n", map->map);
- return -1;
- }
-
- if (map->flags & MAP_ATTRIB) {
- skt->spd_attr[map->map] = speed;
- skt->spd_mem[map->map] = 0;
- } else {
- skt->spd_attr[map->map] = 0;
- skt->spd_mem[map->map] = speed;
- }
-
- if (map->flags & MAP_ATTRIB) {
- map->static_start = skt->phys_attr + map->card_start;
- }
- else {
- map->static_start = skt->phys_mem + map->card_start;
- }
-
- debug("set_mem_map %d start %08lx card_start %08x\n",
- map->map, map->static_start, map->card_start);
- return 0;
-
-} /* au1x00_pcmcia_set_mem_map() */
-
-static struct pccard_operations au1x00_pcmcia_operations = {
- .init = au1x00_pcmcia_sock_init,
- .suspend = au1x00_pcmcia_suspend,
- .get_status = au1x00_pcmcia_get_status,
- .set_socket = au1x00_pcmcia_set_socket,
- .set_io_map = au1x00_pcmcia_set_io_map,
- .set_mem_map = au1x00_pcmcia_set_mem_map,
-};
-
-static const char *skt_names[] = {
- "PCMCIA socket 0",
- "PCMCIA socket 1",
-};
-
-struct skt_dev_info {
- int nskt;
-};
-
-int au1x00_pcmcia_socket_probe(struct device *dev, struct pcmcia_low_level *ops, int first, int nr)
-{
- struct skt_dev_info *sinfo;
- struct au1000_pcmcia_socket *skt;
- int ret, i;
-
- sinfo = kzalloc(sizeof(struct skt_dev_info), GFP_KERNEL);
- if (!sinfo) {
- ret = -ENOMEM;
- goto out;
- }
-
- sinfo->nskt = nr;
-
- /*
- * Initialise the per-socket structure.
- */
- for (i = 0; i < nr; i++) {
- skt = PCMCIA_SOCKET(i);
- memset(skt, 0, sizeof(*skt));
-
- skt->socket.resource_ops = &pccard_static_ops;
- skt->socket.ops = &au1x00_pcmcia_operations;
- skt->socket.owner = ops->owner;
- skt->socket.dev.parent = dev;
-
- init_timer(&skt->poll_timer);
- skt->poll_timer.function = au1x00_pcmcia_poll_event;
- skt->poll_timer.data = (unsigned long)skt;
- skt->poll_timer.expires = jiffies + AU1000_PCMCIA_POLL_PERIOD;
-
- skt->nr = first + i;
- skt->irq = 255;
- skt->dev = dev;
- skt->ops = ops;
-
- skt->res_skt.name = skt_names[skt->nr];
- skt->res_io.name = "io";
- skt->res_io.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
- skt->res_mem.name = "memory";
- skt->res_mem.flags = IORESOURCE_MEM;
- skt->res_attr.name = "attribute";
- skt->res_attr.flags = IORESOURCE_MEM;
-
- /*
- * PCMCIA client drivers use the inb/outb macros to access the
- * IO registers. Since mips_io_port_base is added to the
- * access address of the mips implementation of inb/outb,
- * we need to subtract it here because we want to access the
- * I/O or MEM address directly, without going through this
- * "mips_io_port_base" mechanism.
- */
- if (i == 0) {
- skt->virt_io = (void *)
- (ioremap((phys_t)AU1X_SOCK0_IO, 0x1000) -
- (u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK0_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK0_PHYS_MEM;
- }
- else {
- skt->virt_io = (void *)
- (ioremap((phys_t)AU1X_SOCK1_IO, 0x1000) -
- (u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK1_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK1_PHYS_MEM;
- }
- pcmcia_base_vaddrs[i] = (u32 *)skt->virt_io;
- ret = ops->hw_init(skt);
-
- skt->socket.features = SS_CAP_STATIC_MAP|SS_CAP_PCCARD;
- skt->socket.irq_mask = 0;
- skt->socket.map_size = MAP_SIZE;
- skt->socket.pci_irq = skt->irq;
- skt->socket.io_offset = (unsigned long)skt->virt_io;
-
- skt->status = au1x00_pcmcia_skt_state(skt);
-
- ret = pcmcia_register_socket(&skt->socket);
- if (ret)
- goto out_err;
-
- WARN_ON(skt->socket.sock != i);
-
- add_timer(&skt->poll_timer);
- }
-
- dev_set_drvdata(dev, sinfo);
- return 0;
-
-
-out_err:
- ops->hw_shutdown(skt);
- while (i-- > 0) {
- skt = PCMCIA_SOCKET(i);
-
- del_timer_sync(&skt->poll_timer);
- pcmcia_unregister_socket(&skt->socket);
- if (i == 0) {
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-#ifndef CONFIG_MIPS_XXS1500
- else {
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-#endif
- ops->hw_shutdown(skt);
-
- }
- kfree(sinfo);
-out:
- return ret;
-}
-
-int au1x00_drv_pcmcia_remove(struct platform_device *dev)
-{
- struct skt_dev_info *sinfo = platform_get_drvdata(dev);
- int i;
-
- mutex_lock(&pcmcia_sockets_lock);
- platform_set_drvdata(dev, NULL);
-
- for (i = 0; i < sinfo->nskt; i++) {
- struct au1000_pcmcia_socket *skt = PCMCIA_SOCKET(i);
-
- del_timer_sync(&skt->poll_timer);
- pcmcia_unregister_socket(&skt->socket);
- skt->ops->hw_shutdown(skt);
- au1x00_pcmcia_config_skt(skt, &dead_socket);
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-
- kfree(sinfo);
- mutex_unlock(&pcmcia_sockets_lock);
- return 0;
-}
-
-
-/*
- * PCMCIA "Driver" API
- */
-
-static int au1x00_drv_pcmcia_probe(struct platform_device *dev)
-{
- int i, ret = -ENODEV;
-
- mutex_lock(&pcmcia_sockets_lock);
- for (i=0; i < ARRAY_SIZE(au1x00_pcmcia_hw_init); i++) {
- ret = au1x00_pcmcia_hw_init[i](&dev->dev);
- if (ret == 0)
- break;
- }
- mutex_unlock(&pcmcia_sockets_lock);
- return ret;
-}
-
-static struct platform_driver au1x00_pcmcia_driver = {
- .driver = {
- .name = "au1x00-pcmcia",
- .owner = THIS_MODULE,
- },
- .probe = au1x00_drv_pcmcia_probe,
- .remove = au1x00_drv_pcmcia_remove,
-};
-
-
-/* au1x00_pcmcia_init()
- *
- * This routine performs low-level PCMCIA initialization and then
- * registers this socket driver with Card Services.
- *
- * Returns: 0 on success, -ve error code on failure
- */
-static int __init au1x00_pcmcia_init(void)
-{
- int error = 0;
- error = platform_driver_register(&au1x00_pcmcia_driver);
- return error;
-}
-
-/* au1x00_pcmcia_exit()
- * Invokes the low-level kernel service to free IRQs associated with this
- * socket controller and reset GPIO edge detection.
- */
-static void __exit au1x00_pcmcia_exit(void)
-{
- platform_driver_unregister(&au1x00_pcmcia_driver);
-}
-
-module_init(au1x00_pcmcia_init);
-module_exit(au1x00_pcmcia_exit);
diff --git a/drivers/pcmcia/au1000_generic.h b/drivers/pcmcia/au1000_generic.h
deleted file mode 100644
index 5c36bda..0000000
--- a/drivers/pcmcia/au1000_generic.h
+++ /dev/null
@@ -1,135 +0,0 @@
-/*
- * Alchemy Semi Au1000 pcmcia driver include file
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#ifndef __ASM_AU1000_PCMCIA_H
-#define __ASM_AU1000_PCMCIA_H
-
-/* include the world */
-
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-#include "cs_internal.h"
-
-#define AU1000_PCMCIA_POLL_PERIOD (2*HZ)
-#define AU1000_PCMCIA_IO_SPEED (255)
-#define AU1000_PCMCIA_MEM_SPEED (300)
-
-#define AU1X_SOCK0_IO 0xF00000000ULL
-#define AU1X_SOCK0_PHYS_ATTR 0xF40000000ULL
-#define AU1X_SOCK0_PHYS_MEM 0xF80000000ULL
-
-/* pcmcia socket 1 needs external glue logic so the memory map
- * differs from board to board.
- */
-#if defined(CONFIG_MIPS_PB1000)
-#define AU1X_SOCK1_IO 0xF08000000ULL
-#define AU1X_SOCK1_PHYS_ATTR 0xF48000000ULL
-#define AU1X_SOCK1_PHYS_MEM 0xF88000000ULL
-#endif
-
-struct pcmcia_state {
- unsigned detect: 1,
- ready: 1,
- wrprot: 1,
- bvd1: 1,
- bvd2: 1,
- vs_3v: 1,
- vs_Xv: 1;
-};
-
-struct pcmcia_configure {
- unsigned sock: 8,
- vcc: 8,
- vpp: 8,
- output: 1,
- speaker: 1,
- reset: 1;
-};
-
-struct pcmcia_irqs {
- int sock;
- int irq;
- const char *str;
-};
-
-
-struct au1000_pcmcia_socket {
- struct pcmcia_socket socket;
-
- /*
- * Info from low level handler
- */
- struct device *dev;
- unsigned int nr;
- unsigned int irq;
-
- /*
- * Core PCMCIA state
- */
- struct pcmcia_low_level *ops;
-
- unsigned int status;
- socket_state_t cs_state;
-
- unsigned short spd_io[MAX_IO_WIN];
- unsigned short spd_mem[MAX_WIN];
- unsigned short spd_attr[MAX_WIN];
-
- struct resource res_skt;
- struct resource res_io;
- struct resource res_mem;
- struct resource res_attr;
-
- void * virt_io;
- unsigned int phys_io;
- unsigned int phys_attr;
- unsigned int phys_mem;
- unsigned short speed_io, speed_attr, speed_mem;
-
- unsigned int irq_state;
-
- struct timer_list poll_timer;
-};
-
-struct pcmcia_low_level {
- struct module *owner;
-
- int (*hw_init)(struct au1000_pcmcia_socket *);
- void (*hw_shutdown)(struct au1000_pcmcia_socket *);
-
- void (*socket_state)(struct au1000_pcmcia_socket *, struct pcmcia_state *);
- int (*configure_socket)(struct au1000_pcmcia_socket *, struct socket_state_t *);
-
- /*
- * Enable card status IRQs on (re-)initialisation. This can
- * be called at initialisation, power management event, or
- * pcmcia event.
- */
- void (*socket_init)(struct au1000_pcmcia_socket *);
-
- /*
- * Disable card status IRQs and PCMCIA bus on suspend.
- */
- void (*socket_suspend)(struct au1000_pcmcia_socket *);
-};
-
-extern int au1x_board_init(struct device *dev);
-
-#endif /* __ASM_AU1000_PCMCIA_H */
diff --git a/drivers/pcmcia/au1000_pb1x00.c b/drivers/pcmcia/au1000_pb1x00.c
deleted file mode 100644
index b239664..0000000
--- a/drivers/pcmcia/au1000_pb1x00.c
+++ /dev/null
@@ -1,294 +0,0 @@
-/*
- *
- * Alchemy Semi Pb1000 boards specific pcmcia routines.
- *
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/proc_fs.h>
-#include <linux/types.h>
-
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/au1000.h>
-#include <asm/au1000_pcmcia.h>
-
-#define debug(fmt, arg...) do { } while (0)
-
-#include <asm/pb1000.h>
-#define PCMCIA_IRQ AU1000_GPIO_15
-
-static int pb1x00_pcmcia_init(struct pcmcia_init *init)
-{
- u16 pcr;
- pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
-
- au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */
- au_sync_delay(100);
- au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */
- au_sync();
-
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(20);
-
- return PCMCIA_NUM_SOCKS;
-}
-
-static int pb1x00_pcmcia_shutdown(void)
-{
- u16 pcr;
- pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(20);
- return 0;
-}
-
-static int
-pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
-{
- u32 inserted0, inserted1;
- u16 vs0, vs1;
-
- vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
- inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
- inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
- vs0 = (vs0 >> 4) & 0x3;
- vs1 = (vs1 >> 12) & 0x3;
-
- state->ready = 0;
- state->vs_Xv = 0;
- state->vs_3v = 0;
- state->detect = 0;
-
- if (sock == 0) {
- if (inserted0) {
- switch (vs0) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "pb1x00 bad VS (%d)\n",
- vs0);
- return 0;
- }
- state->detect = 1;
- }
- }
- else {
- if (inserted1) {
- switch (vs1) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "pb1x00 bad VS (%d)\n",
- vs1);
- return 0;
- }
- state->detect = 1;
- }
- }
-
- if (state->detect) {
- state->ready = 1;
- }
-
- state->bvd1=1;
- state->bvd2=1;
- state->wrprot=0;
- return 1;
-}
-
-
-static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
-{
-
- if(info->sock > PCMCIA_MAX_SOCK) return -1;
-
- /*
- * Even in the case of the Pb1000, both sockets are connected
- * to the same irq line.
- */
- info->irq = PCMCIA_IRQ;
-
- return 0;
-}
-
-
-static int
-pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
-{
- u16 pcr;
-
- if(configure->sock > PCMCIA_MAX_SOCK) return -1;
-
- pcr = au_readl(PB1000_PCR);
-
- if (configure->sock == 0) {
- pcr &= ~(PCR_SLOT_0_VCC0 | PCR_SLOT_0_VCC1 |
- PCR_SLOT_0_VPP0 | PCR_SLOT_0_VPP1);
- }
- else {
- pcr &= ~(PCR_SLOT_1_VCC0 | PCR_SLOT_1_VCC1 |
- PCR_SLOT_1_VPP0 | PCR_SLOT_1_VPP1);
- }
-
- pcr &= ~PCR_SLOT_0_RST;
- debug("Vcc %dV Vpp %dV, pcr %x\n",
- configure->vcc, configure->vpp, pcr);
- switch(configure->vcc){
- case 0: /* Vcc 0 */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_GND,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_12V,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_5V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 50: /* Vcc 5V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_GND,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_5V,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_12V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 33: /* Vcc 3.3V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_GND,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_5V,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_12V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- default: /* what's this ? */
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);
- printk(KERN_ERR "%s: bad Vcc %d\n",
- __func__, configure->vcc);
- break;
- }
-
- if (configure->sock == 0) {
- pcr &= ~(PCR_SLOT_0_RST);
- if (configure->reset)
- pcr |= PCR_SLOT_0_RST;
- }
- else {
- pcr &= ~(PCR_SLOT_1_RST);
- if (configure->reset)
- pcr |= PCR_SLOT_1_RST;
- }
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(300);
-
- return 0;
-}
-
-
-struct pcmcia_low_level pb1x00_pcmcia_ops = {
- pb1x00_pcmcia_init,
- pb1x00_pcmcia_shutdown,
- pb1x00_pcmcia_socket_state,
- pb1x00_pcmcia_get_irq_info,
- pb1x00_pcmcia_configure_socket
-};
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
2011-11-01 19:03 ` [PATCH 01/18] MIPS: Alchemy: remove PB1000 support Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:49 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 03/18] MIPS: Alchemy: devboards: remove unneeded BCSR IRQ reg acc Manuel Lauss
` (15 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
I need these gone for upcoming combined DB1000/1500/1100 support.
arch/mips/alchemy/Kconfig | 14 ---
arch/mips/alchemy/Platform | 14 ---
arch/mips/alchemy/devboards/Makefile | 2 -
arch/mips/alchemy/devboards/db1x00/board_setup.c | 105 +---------------------
arch/mips/alchemy/devboards/db1x00/platform.c | 68 +--------------
arch/mips/alchemy/devboards/prom.c | 3 +-
6 files changed, 3 insertions(+), 203 deletions(-)
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 5a48387..36df5e2 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -22,13 +22,6 @@ config MIPS_MTX1
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_BOSPORUS
- bool "Alchemy Bosporus board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_DB1000
bool "Alchemy DB1000 board"
select ALCHEMY_GPIOINT_AU1000
@@ -71,13 +64,6 @@ config MIPS_DB1550
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_MIRAGE
- bool "Alchemy Mirage board"
- select DMA_NONCOHERENT
- select ALCHEMY_GPIOINT_AU1000
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_PB1100
bool "Alchemy PB1100 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 4e07967..2920af9 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -68,20 +68,6 @@ cflags-$(CONFIG_MIPS_DB1200) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1200) += 0xffffffff80100000
#
-# AMD Alchemy Bosporus eval board
-#
-platform-$(CONFIG_MIPS_BOSPORUS) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_BOSPORUS) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_BOSPORUS) += 0xffffffff80100000
-
-#
-# AMD Alchemy Mirage eval board
-#
-platform-$(CONFIG_MIPS_MIRAGE) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_MIRAGE) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_MIRAGE) += 0xffffffff80100000
-
-#
# 4G-Systems eval board
#
platform-$(CONFIG_MIPS_MTX1) += alchemy/mtx-1/
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index bea80d7..5afaf94 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -13,5 +13,3 @@ obj-$(CONFIG_MIPS_DB1100) += db1x00/
obj-$(CONFIG_MIPS_DB1200) += db1200/
obj-$(CONFIG_MIPS_DB1500) += db1x00/
obj-$(CONFIG_MIPS_DB1550) += db1x00/
-obj-$(CONFIG_MIPS_BOSPORUS) += db1x00/
-obj-$(CONFIG_MIPS_MIRAGE) += db1x00/
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
index 7cd36e6..8a222b3 100644
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ b/arch/mips/alchemy/devboards/db1x00/board_setup.c
@@ -40,64 +40,10 @@
#include <prom.h>
-#ifdef CONFIG_MIPS_BOSPORUS
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 11 - miniPCI */
- [12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - SN1741 */
- [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
-};
-
-/*
- * Micrel/Kendin 5 port switch attached to MAC0,
- * MAC0 is associated with PHY address 5 (== WAN port)
- * MAC1 is not associated with any PHY, since it's connected directly
- * to the switch.
- * no interrupts are used
- */
-static struct au1000_eth_platform_data eth0_pdata = {
- .phy_static_config = 1,
- .phy_addr = 5,
-};
-
-static void bosporus_power_off(void)
-{
- while (1)
- asm volatile (".set mips3 ; wait ; .set mips0");
-}
-
-const char *get_system_type(void)
-{
- return "Alchemy Bosporus Gateway Reference";
-}
-#endif
-
-
-#ifdef CONFIG_MIPS_MIRAGE
-static void mirage_power_off(void)
-{
- alchemy_gpio_direction_output(210, 1);
-}
-
-const char *get_system_type(void)
-{
- return "Alchemy Mirage";
-}
-#endif
-
-
-#if defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
-static void mips_softreset(void)
-{
- asm volatile ("jr\t%0" : : "r"(0xbfc00000));
-}
-
-#else
-
const char *get_system_type(void)
{
return "Alchemy Db1x00";
}
-#endif
void __init board_setup(void)
@@ -116,14 +62,6 @@ void __init board_setup(void)
#ifdef CONFIG_MIPS_DB1100
printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
#endif
-#ifdef CONFIG_MIPS_BOSPORUS
- au1xxx_override_eth_cfg(0, ð0_pdata);
-
- printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
-#endif
-#ifdef CONFIG_MIPS_MIRAGE
- printk(KERN_INFO "AMD Alchemy Mirage Board\n");
-#endif
#ifdef CONFIG_MIPS_DB1550
printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
@@ -150,52 +88,11 @@ void __init board_setup(void)
/* Enable GPIO[31:0] inputs */
alchemy_gpio1_input_enable();
-
-#ifdef CONFIG_MIPS_MIRAGE
- {
- u32 pin_func;
-
- /* GPIO[20] is output */
- alchemy_gpio_direction_output(20, 0);
-
- /* Set GPIO[210:208] instead of SSI_0 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_S0;
-
- /* Set GPIO[215:211] for LEDs */
- pin_func |= 5 << 2;
-
- /* Set GPIO[214:213] for more LEDs */
- pin_func |= 5 << 12;
-
- /* Set GPIO[207:200] instead of PCMCIA/LCD */
- pin_func |= SYS_PF_LCD | SYS_PF_PC;
- au_writel(pin_func, SYS_PINFUNC);
-
- /*
- * Enable speaker amplifier. This should
- * be part of the audio driver.
- */
- alchemy_gpio_direction_output(209, 1);
-
- pm_power_off = mirage_power_off;
- _machine_halt = mirage_power_off;
- _machine_restart = (void(*)(char *))mips_softreset;
- }
-#endif
-
-#ifdef CONFIG_MIPS_BOSPORUS
- pm_power_off = bosporus_power_off;
- _machine_halt = bosporus_power_off;
- _machine_restart = (void(*)(char *))mips_softreset;
-#endif
- au_sync();
}
static int __init db1x00_init_irq(void)
{
-#if defined(CONFIG_MIPS_MIRAGE)
- irq_set_irq_type(AU1500_GPIO7_INT, IRQF_TRIGGER_RISING); /* TS pendown */
-#elif defined(CONFIG_MIPS_DB1550)
+#if defined(CONFIG_MIPS_DB1550)
irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW); /* CD1# */
irq_set_irq_type(AU1550_GPIO3_INT, IRQF_TRIGGER_LOW); /* CARD0# */
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
index c40b968..a8bb4fa 100644
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ b/arch/mips/alchemy/devboards/db1x00/platform.c
@@ -36,7 +36,6 @@ struct pci_dev;
* Db1550: 0/1, 21/22, 3/5
*/
-#define DB1XXX_HAS_PCMCIA
#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
#if defined(CONFIG_MIPS_DB1000)
@@ -47,7 +46,6 @@ struct pci_dev;
#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
-#define BOARD_FLASH_WIDTH 4 /* 32-bits */
#elif defined(CONFIG_MIPS_DB1100)
#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
@@ -56,7 +54,6 @@ struct pci_dev;
#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
-#define BOARD_FLASH_WIDTH 4 /* 32-bits */
#elif defined(CONFIG_MIPS_DB1500)
#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
@@ -65,7 +62,6 @@ struct pci_dev;
#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
-#define BOARD_FLASH_WIDTH 4 /* 32-bits */
#elif defined(CONFIG_MIPS_DB1550)
#define DB1XXX_PCMCIA_CD0 AU1550_GPIO0_INT
#define DB1XXX_PCMCIA_STSCHG0 AU1550_GPIO21_INT
@@ -74,19 +70,6 @@ struct pci_dev;
#define DB1XXX_PCMCIA_STSCHG1 AU1550_GPIO22_INT
#define DB1XXX_PCMCIA_CARD1 AU1550_GPIO5_INT
#define BOARD_FLASH_SIZE 0x08000000 /* 128MB */
-#define BOARD_FLASH_WIDTH 4 /* 32-bits */
-#else
-/* other board: no PCMCIA */
-#undef DB1XXX_HAS_PCMCIA
-#undef F_SWAPPED
-#define F_SWAPPED 0
-#if defined(CONFIG_MIPS_BOSPORUS)
-#define BOARD_FLASH_SIZE 0x01000000 /* 16MB */
-#define BOARD_FLASH_WIDTH 2 /* 16-bits */
-#elif defined(CONFIG_MIPS_MIRAGE)
-#define BOARD_FLASH_SIZE 0x04000000 /* 64MB */
-#define BOARD_FLASH_WIDTH 4 /* 32-bits */
-#endif
#endif
#ifdef CONFIG_PCI
@@ -136,52 +119,6 @@ static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
}
#endif
-#ifdef CONFIG_MIPS_BOSPORUS
-static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 11) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 11) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- default: return 0xff;
- }
- }
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-#endif
-
-#ifdef CONFIG_MIPS_MIRAGE
-static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 11) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 11)
- return (pin == 1) ? AU1500_PCI_INTD : 0xff;
- if (slot == 12)
- return (pin == 3) ? AU1500_PCI_INTC : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- default: return 0xff;
- }
- }
- return -1;
-}
-#endif
-
static struct resource alchemy_pci_host_res[] = {
[0] = {
.start = AU1500_PCI_PHYS_ADDR,
@@ -279,7 +216,6 @@ static struct platform_device db1x00_audio_dev = {
static int __init db1xxx_dev_init(void)
{
-#ifdef DB1XXX_HAS_PCMCIA
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
@@ -299,17 +235,15 @@ static int __init db1xxx_dev_init(void)
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
/*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
-#endif
#ifdef CONFIG_MIPS_DB1100
platform_device_register(&au1100_lcd_device);
#endif
- db1x_register_norflash(BOARD_FLASH_SIZE, BOARD_FLASH_WIDTH, F_SWAPPED);
-
platform_device_register(&db1x00_codec_dev);
platform_device_register(&alchemy_ac97c_dma_dev);
platform_device_register(&alchemy_ac97c_dev);
platform_device_register(&db1x00_audio_dev);
+ db1x_register_norflash(BOARD_FLASH_SIZE, 4 /* 32bit */, F_SWAPPED);
return 0;
}
device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index 56d7ea5..f734833 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -35,8 +35,7 @@
#if defined(CONFIG_MIPS_DB1000) || \
defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
- defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500) || \
- defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
+ defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500)
#define ALCHEMY_BOARD_DEFAULT_MEMSIZE 0x04000000
#else /* Au1550/Au1200-based develboards */
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 03/18] MIPS: Alchemy: devboards: remove unneeded BCSR IRQ reg acc
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
2011-11-01 19:03 ` [PATCH 01/18] MIPS: Alchemy: remove PB1000 support Manuel Lauss
2011-11-01 19:03 ` [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:49 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 04/18] MIPS: Alchemy: Au1300 SoC support Manuel Lauss
` (14 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Initially I had to write to both the MASK and ENABLE registers,
otherwise the CPLD would generate tons of spurious interrupts.
With the change to the demux handler to disable the muxed line,
it is now sufficient to disable the interrupt by writing either
the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/devboards/bcsr.c | 11 ++---------
1 files changed, 2 insertions(+), 9 deletions(-)
diff --git a/arch/mips/alchemy/devboards/bcsr.c b/arch/mips/alchemy/devboards/bcsr.c
index 463d2c4..1e83ce2 100644
--- a/arch/mips/alchemy/devboards/bcsr.c
+++ b/arch/mips/alchemy/devboards/bcsr.c
@@ -97,14 +97,9 @@ static void bcsr_csc_handler(unsigned int irq, struct irq_desc *d)
enable_irq(irq);
}
-/* NOTE: both the enable and mask bits must be cleared, otherwise the
- * CPLD generates tons of spurious interrupts (at least on my DB1200).
- * -- mlau
- */
static void bcsr_irq_mask(struct irq_data *d)
{
unsigned short v = 1 << (d->irq - bcsr_csc_base);
- __raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
wmb();
}
@@ -112,7 +107,6 @@ static void bcsr_irq_mask(struct irq_data *d)
static void bcsr_irq_maskack(struct irq_data *d)
{
unsigned short v = 1 << (d->irq - bcsr_csc_base);
- __raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
__raw_writew(v, bcsr_virt + BCSR_REG_INTSTAT); /* ack */
wmb();
@@ -121,7 +115,6 @@ static void bcsr_irq_maskack(struct irq_data *d)
static void bcsr_irq_unmask(struct irq_data *d)
{
unsigned short v = 1 << (d->irq - bcsr_csc_base);
- __raw_writew(v, bcsr_virt + BCSR_REG_INTSET);
__raw_writew(v, bcsr_virt + BCSR_REG_MASKSET);
wmb();
}
@@ -137,9 +130,9 @@ void __init bcsr_init_irq(int csc_start, int csc_end, int hook_irq)
{
unsigned int irq;
- /* mask & disable & ack all */
- __raw_writew(0xffff, bcsr_virt + BCSR_REG_INTCLR);
+ /* mask & enable & ack all */
__raw_writew(0xffff, bcsr_virt + BCSR_REG_MASKCLR);
+ __raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSET);
__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSTAT);
wmb();
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 04/18] MIPS: Alchemy: Au1300 SoC support
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (2 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 03/18] MIPS: Alchemy: devboards: remove unneeded BCSR IRQ reg acc Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 05/18] MIPS: Alchemy: DB1300 support Manuel Lauss
` (13 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Kconfig | 4 +
arch/mips/alchemy/common/Makefile | 3 +-
arch/mips/alchemy/common/dbdma.c | 46 +++
arch/mips/alchemy/common/gpioint.c | 411 ++++++++++++++++++++++
arch/mips/alchemy/common/gpiolib.c | 42 +++
arch/mips/alchemy/common/platform.c | 31 ++-
arch/mips/alchemy/common/power.c | 3 +
arch/mips/alchemy/common/sleeper.S | 73 ++++
arch/mips/alchemy/common/time.c | 1 +
arch/mips/alchemy/common/vss.c | 84 +++++
arch/mips/include/asm/cpu.h | 1 +
arch/mips/include/asm/mach-au1x00/au1000.h | 221 +++++++++++-
arch/mips/include/asm/mach-au1x00/au1100_mmc.h | 2 +
arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h | 31 ++
arch/mips/include/asm/mach-au1x00/gpio-au1300.h | 241 +++++++++++++
arch/mips/include/asm/mach-au1x00/gpio.h | 3 +
arch/mips/kernel/cpu-probe.c | 7 +
drivers/i2c/busses/Kconfig | 4 +-
drivers/mmc/host/au1xmmc.c | 45 ++-
drivers/spi/Kconfig | 4 +-
drivers/usb/host/alchemy-common.c | 277 +++++++++++++++
drivers/usb/host/ohci-au1xxx.c | 13 +-
drivers/video/Kconfig | 8 +-
sound/soc/au1x/Kconfig | 6 +-
24 files changed, 1514 insertions(+), 47 deletions(-)
create mode 100644 arch/mips/alchemy/common/gpioint.c
create mode 100644 arch/mips/alchemy/common/vss.c
create mode 100644 arch/mips/include/asm/mach-au1x00/gpio-au1300.h
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 36df5e2..766bada 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -2,6 +2,10 @@
config ALCHEMY_GPIOINT_AU1000
bool
+# au1300-style GPIO/INT controller
+config ALCHEMY_GPIOINT_AU1300
+ bool
+
# select this in your board config if you don't want to use the gpio
# namespace as documented in the manuals. In this case however you need
# to create the necessary gpio_* functions in your board code/headers!
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
index 811ece7..d3f5c51 100644
--- a/arch/mips/alchemy/common/Makefile
+++ b/arch/mips/alchemy/common/Makefile
@@ -6,9 +6,10 @@
#
obj-y += prom.o time.o clocks.o platform.o power.o setup.o \
- sleeper.o dma.o dbdma.o
+ sleeper.o dma.o dbdma.o vss.o
obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o
+obj-$(CONFIG_ALCHEMY_GPIOINT_AU1300) += gpioint.o
# optional gpiolib support
ifeq ($(CONFIG_ALCHEMY_GPIO_INDIRECT),)
diff --git a/arch/mips/alchemy/common/dbdma.c b/arch/mips/alchemy/common/dbdma.c
index 0e63ee4..c723ec1 100644
--- a/arch/mips/alchemy/common/dbdma.c
+++ b/arch/mips/alchemy/common/dbdma.c
@@ -148,6 +148,50 @@ static dbdev_tab_t au1200_dbdev_tab[] __initdata = {
{ DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
};
+static dbdev_tab_t au1300_dbdev_tab[] __initdata = {
+ { AU1300_DSCR_CMD0_UART0_TX, DEV_FLAGS_OUT, 0, 8, 0x10100004, 0, 0 },
+ { AU1300_DSCR_CMD0_UART0_RX, DEV_FLAGS_IN, 0, 8, 0x10100000, 0, 0 },
+ { AU1300_DSCR_CMD0_UART1_TX, DEV_FLAGS_OUT, 0, 8, 0x10101004, 0, 0 },
+ { AU1300_DSCR_CMD0_UART1_RX, DEV_FLAGS_IN, 0, 8, 0x10101000, 0, 0 },
+ { AU1300_DSCR_CMD0_UART2_TX, DEV_FLAGS_OUT, 0, 8, 0x10102004, 0, 0 },
+ { AU1300_DSCR_CMD0_UART2_RX, DEV_FLAGS_IN, 0, 8, 0x10102000, 0, 0 },
+ { AU1300_DSCR_CMD0_UART3_TX, DEV_FLAGS_OUT, 0, 8, 0x10103004, 0, 0 },
+ { AU1300_DSCR_CMD0_UART3_RX, DEV_FLAGS_IN, 0, 8, 0x10103000, 0, 0 },
+
+ { AU1300_DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 4, 8, 0x10600000, 0, 0 },
+ { AU1300_DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN, 4, 8, 0x10600004, 0, 0 },
+ { AU1300_DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 8, 8, 0x10601000, 0, 0 },
+ { AU1300_DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN, 8, 8, 0x10601004, 0, 0 },
+
+ { AU1300_DSCR_CMD0_AES_RX, DEV_FLAGS_IN , 4, 32, 0x10300008, 0, 0 },
+ { AU1300_DSCR_CMD0_AES_TX, DEV_FLAGS_OUT, 4, 32, 0x10300004, 0, 0 },
+
+ { AU1300_DSCR_CMD0_PSC0_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0001c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC0_RX, DEV_FLAGS_IN, 0, 16, 0x10a0001c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC1_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0101c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC1_RX, DEV_FLAGS_IN, 0, 16, 0x10a0101c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC2_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0201c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC2_RX, DEV_FLAGS_IN, 0, 16, 0x10a0201c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC3_TX, DEV_FLAGS_OUT, 0, 16, 0x10a0301c, 0, 0 },
+ { AU1300_DSCR_CMD0_PSC3_RX, DEV_FLAGS_IN, 0, 16, 0x10a0301c, 0, 0 },
+
+ { AU1300_DSCR_CMD0_LCD, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+ { AU1300_DSCR_CMD0_NAND_FLASH, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 },
+
+ { AU1300_DSCR_CMD0_SDMS_TX2, DEV_FLAGS_OUT, 4, 8, 0x10602000, 0, 0 },
+ { AU1300_DSCR_CMD0_SDMS_RX2, DEV_FLAGS_IN, 4, 8, 0x10602004, 0, 0 },
+
+ { AU1300_DSCR_CMD0_CIM_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+
+ { AU1300_DSCR_CMD0_UDMA, DEV_FLAGS_ANYUSE, 0, 32, 0x14001810, 0, 0 },
+
+ { AU1300_DSCR_CMD0_DMA_REQ0, 0, 0, 0, 0x00000000, 0, 0 },
+ { AU1300_DSCR_CMD0_DMA_REQ1, 0, 0, 0, 0x00000000, 0, 0 },
+
+ { DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+ { DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+};
+
/* 32 predefined plus 32 custom */
#define DBDEV_TAB_SIZE 64
@@ -1038,6 +1082,8 @@ static int __init alchemy_dbdma_init(void)
return dbdma_setup(AU1550_DDMA_INT, au1550_dbdev_tab);
case ALCHEMY_CPU_AU1200:
return dbdma_setup(AU1200_DDMA_INT, au1200_dbdev_tab);
+ case ALCHEMY_CPU_AU1300:
+ return dbdma_setup(AU1300_DDMA_INT, au1300_dbdev_tab);
}
return 0;
}
diff --git a/arch/mips/alchemy/common/gpioint.c b/arch/mips/alchemy/common/gpioint.c
new file mode 100644
index 0000000..b8cd336
--- /dev/null
+++ b/arch/mips/alchemy/common/gpioint.c
@@ -0,0 +1,411 @@
+/*
+ * gpioint.c - Au1300 GPIO+Interrupt controller (I call it "GPIC") support.
+ *
+ * Copyright (c) 2009-2011 Manuel Lauss <manuel.lauss@googlemail.com>
+ *
+ * licensed under the GPLv2.
+ */
+
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/syscore_ops.h>
+#include <linux/types.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
+
+static int au1300_gpic_settype(struct irq_data *d, unsigned int type);
+
+/* setup for known onchip sources */
+struct gpic_devint_data {
+ int irq; /* linux IRQ number */
+ int type; /* IRQ_TYPE_ */
+ int prio; /* irq priority, 0 highest, 3 lowest */
+ int internal; /* internal source (no ext. pin)? */
+};
+
+static const struct gpic_devint_data au1300_devints[] __initdata = {
+ /* multifunction: gpio pin or device */
+ { AU1300_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_UART2_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_SD1_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_SD2_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_PSC2_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_PSC3_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ { AU1300_NAND_INT, IRQ_TYPE_LEVEL_HIGH, 1, 0, },
+ /* au1300 internal */
+ { AU1300_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_MMU_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_MPU_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_GPU_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_UDMA_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_TOY_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_RTC_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0, 1, },
+ { AU1300_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_SD0_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_USB_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_BSA_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_MPE_INT, IRQ_TYPE_EDGE_RISING, 1, 1, },
+ { AU1300_ITE_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_AES_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { AU1300_CIM_INT, IRQ_TYPE_LEVEL_HIGH, 1, 1, },
+ { -1, }, /* terminator */
+};
+
+
+/*
+ * au1300_gpic_chgcfg - change PIN configuration.
+ * @gpio: pin to change (0-based GPIO number from datasheet).
+ * @clr: clear all bits set in 'clr'.
+ * @set: set these bits.
+ *
+ * modifies a pins' configuration register, bits set in @clr will
+ * be cleared in the register, bits in @set will be set.
+ */
+static inline void au1300_gpic_chgcfg(unsigned int gpio,
+ unsigned long clr,
+ unsigned long set)
+{
+ void __iomem *r = AU1300_GPIC_ADDR;
+ unsigned long l;
+
+ r += gpio * 4; /* offset into pin config array */
+ l = __raw_readl(r + AU1300_GPIC_PINCFG);
+ l &= ~clr;
+ l |= set;
+ __raw_writel(l, r + AU1300_GPIC_PINCFG);
+ wmb();
+}
+
+/*
+ * au1300_pinfunc_to_gpio - assign a pin as GPIO input (GPIO ctrl).
+ * @pin: pin (0-based GPIO number from datasheet).
+ *
+ * Assigns a GPIO pin to the GPIO controller, so its level can either
+ * be read or set through the generic GPIO functions.
+ * If you need a GPOUT, use au1300_gpio_set_value(pin, 0/1).
+ * REVISIT: is this function really necessary?
+ */
+void au1300_pinfunc_to_gpio(enum au1300_multifunc_pins gpio)
+{
+ au1300_gpio_direction_input(gpio + AU1300_GPIO_BASE);
+}
+EXPORT_SYMBOL_GPL(au1300_pinfunc_to_gpio);
+
+/*
+ * au1300_pinfunc_to_dev - assign a pin to the device function.
+ * @pin: pin (0-based GPIO number from datasheet).
+ *
+ * Assigns a GPIO pin to its associated device function; the pin will be
+ * driven by the device and not through GPIO functions.
+ */
+void au1300_pinfunc_to_dev(enum au1300_multifunc_pins gpio)
+{
+ void __iomem *r = AU1300_GPIC_ADDR;
+ unsigned long bit;
+
+ r += GPIC_GPIO_BANKOFF(gpio);
+ bit = GPIC_GPIO_TO_BIT(gpio);
+ __raw_writel(bit, r + AU1300_GPIC_DEVSEL);
+ wmb();
+}
+EXPORT_SYMBOL_GPL(au1300_pinfunc_to_dev);
+
+/*
+ * au1300_set_irq_priority - set internal priority of IRQ.
+ * @irq: irq to set priority (linux irq number).
+ * @p: priority (0 = highest, 3 = lowest).
+ */
+void au1300_set_irq_priority(unsigned int irq, int p)
+{
+ irq -= ALCHEMY_GPIC_INT_BASE;
+ au1300_gpic_chgcfg(irq, GPIC_CFG_IL_MASK, GPIC_CFG_IL_SET(p));
+}
+EXPORT_SYMBOL_GPL(au1300_set_irq_priority);
+
+/*
+ * au1300_set_dbdma_gpio - assign a gpio to one of the DBDMA triggers.
+ * @dchan: dbdma trigger select (0, 1).
+ * @gpio: pin to assign as trigger.
+ *
+ * DBDMA controller has 2 external trigger sources; this function
+ * assigns a GPIO to the selected trigger.
+ */
+void au1300_set_dbdma_gpio(int dchan, unsigned int gpio)
+{
+ unsigned long r;
+
+ if ((dchan >= 0) && (dchan <= 1)) {
+ r = __raw_readl(AU1300_GPIC_ADDR + AU1300_GPIC_DMASEL);
+ r &= ~(0xff << (8 * dchan));
+ r |= (gpio & 0x7f) << (8 * dchan);
+ __raw_writel(r, AU1300_GPIC_ADDR + AU1300_GPIC_DMASEL);
+ wmb();
+ }
+}
+
+/**********************************************************************/
+
+static inline void gpic_pin_set_idlewake(unsigned int gpio, int allow)
+{
+ au1300_gpic_chgcfg(gpio, GPIC_CFG_IDLEWAKE,
+ allow ? GPIC_CFG_IDLEWAKE : 0);
+}
+
+static void au1300_gpic_mask(struct irq_data *d)
+{
+ void __iomem *r = AU1300_GPIC_ADDR;
+ unsigned long bit, irq = d->irq;
+
+ irq -= ALCHEMY_GPIC_INT_BASE;
+ r += GPIC_GPIO_BANKOFF(irq);
+ bit = GPIC_GPIO_TO_BIT(irq);
+ __raw_writel(bit, r + AU1300_GPIC_IDIS);
+ wmb();
+
+ gpic_pin_set_idlewake(irq, 0);
+}
+
+static void au1300_gpic_unmask(struct irq_data *d)
+{
+ void __iomem *r = AU1300_GPIC_ADDR;
+ unsigned long bit, irq = d->irq;
+
+ irq -= ALCHEMY_GPIC_INT_BASE;
+
+ gpic_pin_set_idlewake(irq, 1);
+
+ r += GPIC_GPIO_BANKOFF(irq);
+ bit = GPIC_GPIO_TO_BIT(irq);
+ __raw_writel(bit, r + AU1300_GPIC_IEN);
+ wmb();
+}
+
+static void au1300_gpic_maskack(struct irq_data *d)
+{
+ void __iomem *r = AU1300_GPIC_ADDR;
+ unsigned long bit, irq = d->irq;
+
+ irq -= ALCHEMY_GPIC_INT_BASE;
+ r += GPIC_GPIO_BANKOFF(irq);
+ bit = GPIC_GPIO_TO_BIT(irq);
+ __raw_writel(bit, r + AU1300_GPIC_IPEND); /* ack */
+ __raw_writel(bit, r + AU1300_GPIC_IDIS); /* mask */
+ wmb();
+
+ gpic_pin_set_idlewake(irq, 0);
+}
+
+static void au1300_gpic_ack(struct irq_data *d)
+{
+ void __iomem *r = AU1300_GPIC_ADDR;
+ unsigned long bit, irq = d->irq;
+
+ irq -= ALCHEMY_GPIC_INT_BASE;
+ r += GPIC_GPIO_BANKOFF(irq);
+ bit = GPIC_GPIO_TO_BIT(irq);
+ __raw_writel(bit, r + AU1300_GPIC_IPEND); /* ack */
+ wmb();
+}
+
+static struct irq_chip au1300_gpic = {
+ .name = "GPIOINT",
+ .irq_ack = au1300_gpic_ack,
+ .irq_mask = au1300_gpic_mask,
+ .irq_mask_ack = au1300_gpic_maskack,
+ .irq_unmask = au1300_gpic_unmask,
+ .irq_set_type = au1300_gpic_settype,
+};
+
+static int au1300_gpic_settype(struct irq_data *d, unsigned int type)
+{
+ unsigned long s;
+ unsigned char *name = NULL;
+ irq_flow_handler_t hdl = NULL;
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_HIGH:
+ s = GPIC_CFG_IC_LEVEL_HIGH;
+ name = "high";
+ hdl = handle_level_irq;
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ s = GPIC_CFG_IC_LEVEL_LOW;
+ name = "low";
+ hdl = handle_level_irq;
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ s = GPIC_CFG_IC_EDGE_RISE;
+ name = "posedge";
+ hdl = handle_edge_irq;
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ s = GPIC_CFG_IC_EDGE_FALL;
+ name = "negedge";
+ hdl = handle_edge_irq;
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ s = GPIC_CFG_IC_EDGE_BOTH;
+ name = "bothedge";
+ hdl = handle_edge_irq;
+ break;
+ case IRQ_TYPE_NONE:
+ s = GPIC_CFG_IC_OFF;
+ name = "disabled";
+ hdl = handle_level_irq;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ __irq_set_chip_handler_name_locked(d->irq, &au1300_gpic, hdl, name);
+
+ au1300_gpic_chgcfg(d->irq - ALCHEMY_GPIC_INT_BASE, GPIC_CFG_IC_MASK, s);
+
+ return 0;
+}
+
+static void __init alchemy_gpic_init_irq(const struct gpic_devint_data *dints)
+{
+ int i;
+ void __iomem *bank_base;
+
+ mips_cpu_irq_init();
+
+ /* disable & ack all possible interrupt sources */
+ for (i = 0; i < 4; i++) {
+ bank_base = AU1300_GPIC_ADDR + (i * 4);
+ __raw_writel(~0UL, bank_base + AU1300_GPIC_IDIS);
+ wmb();
+ __raw_writel(~0UL, bank_base + AU1300_GPIC_IPEND);
+ wmb();
+ }
+
+ /* register an irq_chip for them, with 2nd highest priority */
+ for (i = ALCHEMY_GPIC_INT_BASE; i <= ALCHEMY_GPIC_INT_LAST; i++) {
+ au1300_set_irq_priority(i, 1);
+ au1300_gpic_settype(irq_get_irq_data(i), IRQ_TYPE_NONE);
+ }
+
+ /* setup known on-chip sources */
+ while ((i = dints->irq) != -1) {
+ au1300_gpic_settype(irq_get_irq_data(i), dints->type);
+ au1300_set_irq_priority(i, dints->prio);
+
+ if (dints->internal)
+ au1300_pinfunc_to_dev(i - ALCHEMY_GPIC_INT_BASE);
+
+ dints++;
+ }
+
+ set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3);
+}
+
+static unsigned long alchemy_gpic_pmdata[ALCHEMY_GPIC_INT_NUM + 6];
+
+static int alchemy_gpic_suspend(void)
+{
+ void __iomem *base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR);
+ int i;
+
+ /* save 4 interrupt mask status registers */
+ alchemy_gpic_pmdata[0] = __raw_readl(base + AU1300_GPIC_IEN + 0x0);
+ alchemy_gpic_pmdata[1] = __raw_readl(base + AU1300_GPIC_IEN + 0x4);
+ alchemy_gpic_pmdata[2] = __raw_readl(base + AU1300_GPIC_IEN + 0x8);
+ alchemy_gpic_pmdata[3] = __raw_readl(base + AU1300_GPIC_IEN + 0xc);
+
+ /* save misc register(s) */
+ alchemy_gpic_pmdata[4] = __raw_readl(base + AU1300_GPIC_DMASEL);
+
+ /* molto silenzioso */
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x0);
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x4);
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x8);
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0xc);
+ wmb();
+
+ /* save pin/int-type configuration */
+ base += AU1300_GPIC_PINCFG;
+ for (i = 0; i < ALCHEMY_GPIC_INT_NUM; i++)
+ alchemy_gpic_pmdata[i + 5] = __raw_readl(base + (i << 2));
+
+ wmb();
+
+ return 0;
+}
+
+static void alchemy_gpic_resume(void)
+{
+ void __iomem *base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR);
+ int i;
+
+ /* disable all first */
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x0);
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x4);
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x8);
+ __raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0xc);
+ wmb();
+
+ /* restore pin/int-type configurations */
+ base += AU1300_GPIC_PINCFG;
+ for (i = 0; i < ALCHEMY_GPIC_INT_NUM; i++)
+ __raw_writel(alchemy_gpic_pmdata[i + 5], base + (i << 2));
+ wmb();
+
+ /* restore misc register(s) */
+ base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR);
+ __raw_writel(alchemy_gpic_pmdata[4], base + AU1300_GPIC_DMASEL);
+ wmb();
+
+ /* finally restore masks */
+ __raw_writel(alchemy_gpic_pmdata[0], base + AU1300_GPIC_IEN + 0x0);
+ __raw_writel(alchemy_gpic_pmdata[1], base + AU1300_GPIC_IEN + 0x4);
+ __raw_writel(alchemy_gpic_pmdata[2], base + AU1300_GPIC_IEN + 0x8);
+ __raw_writel(alchemy_gpic_pmdata[3], base + AU1300_GPIC_IEN + 0xc);
+ wmb();
+}
+
+static struct syscore_ops alchemy_gpic_pmops = {
+ .suspend = alchemy_gpic_suspend,
+ .resume = alchemy_gpic_resume,
+};
+
+/**********************************************************************/
+
+void __init arch_init_irq(void)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1300:
+ alchemy_gpic_init_irq(&au1300_devints[0]);
+ register_syscore_ops(&alchemy_gpic_pmops);
+ break;
+ }
+}
+
+#define CAUSEF_GPIC (CAUSEF_IP2 | CAUSEF_IP3 | CAUSEF_IP4 | CAUSEF_IP5)
+
+void plat_irq_dispatch(void)
+{
+ unsigned long i, c = read_c0_cause() & read_c0_status();
+
+ if (c & CAUSEF_IP7) /* c0 timer */
+ do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+ else if (likely(c & CAUSEF_GPIC)) {
+ i = __raw_readl(AU1300_GPIC_ADDR + AU1300_GPIC_PRIENC);
+ do_IRQ(i + ALCHEMY_GPIC_INT_BASE);
+ } else
+ spurious_interrupt();
+}
diff --git a/arch/mips/alchemy/common/gpiolib.c b/arch/mips/alchemy/common/gpiolib.c
index 91fb4d9..f1b50f0 100644
--- a/arch/mips/alchemy/common/gpiolib.c
+++ b/arch/mips/alchemy/common/gpiolib.c
@@ -27,6 +27,7 @@
* CONFIG_ALCHEMY_GPIO_INDIRECT=n, otherwise compilation will fail!
* au1000 SoC have only one GPIO block : GPIO1
* Au1100, Au15x0, Au12x0 have a second one : GPIO2
+ * Au1300 is totally different: 1 block with up to 128 GPIOs
*/
#include <linux/init.h>
@@ -35,6 +36,7 @@
#include <linux/types.h>
#include <linux/gpio.h>
#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
static int gpio2_get(struct gpio_chip *chip, unsigned offset)
{
@@ -115,6 +117,43 @@ struct gpio_chip alchemy_gpio_chip[] = {
},
};
+static int alchemy_gpic_get(struct gpio_chip *chip, unsigned int off)
+{
+ return au1300_gpio_get_value(off + AU1300_GPIO_BASE);
+}
+
+static void alchemy_gpic_set(struct gpio_chip *chip, unsigned int off, int v)
+{
+ au1300_gpio_set_value(off + AU1300_GPIO_BASE, v);
+}
+
+static int alchemy_gpic_dir_input(struct gpio_chip *chip, unsigned int off)
+{
+ return au1300_gpio_direction_input(off + AU1300_GPIO_BASE);
+}
+
+static int alchemy_gpic_dir_output(struct gpio_chip *chip, unsigned int off,
+ int v)
+{
+ return au1300_gpio_direction_output(off + AU1300_GPIO_BASE, v);
+}
+
+static int alchemy_gpic_gpio_to_irq(struct gpio_chip *chip, unsigned int off)
+{
+ return au1300_gpio_to_irq(off + AU1300_GPIO_BASE);
+}
+
+static struct gpio_chip au1300_gpiochip = {
+ .label = "alchemy-gpic",
+ .direction_input = alchemy_gpic_dir_input,
+ .direction_output = alchemy_gpic_dir_output,
+ .get = alchemy_gpic_get,
+ .set = alchemy_gpic_set,
+ .to_irq = alchemy_gpic_gpio_to_irq,
+ .base = AU1300_GPIO_BASE,
+ .ngpio = AU1300_GPIO_NUM,
+};
+
static int __init alchemy_gpiochip_init(void)
{
int ret = 0;
@@ -127,6 +166,9 @@ static int __init alchemy_gpiochip_init(void)
ret = gpiochip_add(&alchemy_gpio_chip[0]);
ret |= gpiochip_add(&alchemy_gpio_chip[1]);
break;
+ case ALCHEMY_CPU_AU1300:
+ ret = gpiochip_add(&au1300_gpiochip);
+ break;
}
return ret;
}
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index c8e5d72..95cb911 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -82,6 +82,12 @@ static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = {
PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT),
PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT),
},
+ [ALCHEMY_CPU_AU1300] = {
+ PORT(AU1300_UART0_PHYS_ADDR, AU1300_UART0_INT),
+ PORT(AU1300_UART1_PHYS_ADDR, AU1300_UART1_INT),
+ PORT(AU1300_UART2_PHYS_ADDR, AU1300_UART2_INT),
+ PORT(AU1300_UART3_PHYS_ADDR, AU1300_UART3_INT),
+ },
};
static struct platform_device au1xx0_uart_device = {
@@ -122,10 +128,12 @@ static unsigned long alchemy_ohci_data[][2] __initdata = {
[ALCHEMY_CPU_AU1100] = { AU1000_USB_OHCI_PHYS_ADDR, AU1100_USB_HOST_INT },
[ALCHEMY_CPU_AU1550] = { AU1550_USB_OHCI_PHYS_ADDR, AU1550_USB_HOST_INT },
[ALCHEMY_CPU_AU1200] = { AU1200_USB_OHCI_PHYS_ADDR, AU1200_USB_INT },
+ [ALCHEMY_CPU_AU1300] = { AU1300_USB_OHCI0_PHYS_ADDR, AU1300_USB_INT },
};
static unsigned long alchemy_ehci_data[][2] __initdata = {
[ALCHEMY_CPU_AU1200] = { AU1200_USB_EHCI_PHYS_ADDR, AU1200_USB_INT },
+ [ALCHEMY_CPU_AU1300] = { AU1300_USB_EHCI_PHYS_ADDR, AU1300_USB_INT },
};
static int __init _new_usbres(struct resource **r, struct platform_device **d)
@@ -169,8 +177,8 @@ static void __init alchemy_setup_usb(int ctype)
printk(KERN_INFO "Alchemy USB: cannot add OHCI0\n");
- /* setup EHCI0: Au1200 */
- if (ctype == ALCHEMY_CPU_AU1200) {
+ /* setup EHCI0: Au1200/Au1300 */
+ if ((ctype == ALCHEMY_CPU_AU1200) || (ctype == ALCHEMY_CPU_AU1300)) {
if (_new_usbres(&res, &pdev))
return;
@@ -187,6 +195,25 @@ static void __init alchemy_setup_usb(int ctype)
if (platform_device_register(pdev))
printk(KERN_INFO "Alchemy USB: cannot add EHCI0\n");
}
+
+ /* Au1300: OHCI1 */
+ if (ctype == ALCHEMY_CPU_AU1300) {
+ if (_new_usbres(&res, &pdev))
+ return;
+
+ res[0].start = AU1300_USB_OHCI1_PHYS_ADDR;
+ res[0].end = res[0].start + 0x100 - 1;
+ res[0].flags = IORESOURCE_MEM;
+ res[1].start = AU1300_USB_INT;
+ res[1].end = res[1].start;
+ res[1].flags = IORESOURCE_IRQ;
+ pdev->name = "au1xxx-ohci";
+ pdev->id = 1;
+ pdev->dev.dma_mask = &alchemy_ohci_dmamask;
+
+ if (platform_device_register(pdev))
+ printk(KERN_INFO "Alchemy USB: cannot add OHCI1\n");
+ }
}
/* Macro to help defining the Ethernet MAC resources */
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index bdd6651..0c7fce2 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -126,6 +126,9 @@ void au_sleep(void)
case ALCHEMY_CPU_AU1200:
alchemy_sleep_au1550();
break;
+ case ALCHEMY_CPU_AU1300:
+ alchemy_sleep_au1300();
+ break;
}
restore_core_regs();
diff --git a/arch/mips/alchemy/common/sleeper.S b/arch/mips/alchemy/common/sleeper.S
index 77f3c74..c7bcc7e 100644
--- a/arch/mips/alchemy/common/sleeper.S
+++ b/arch/mips/alchemy/common/sleeper.S
@@ -153,6 +153,79 @@ LEAF(alchemy_sleep_au1550)
END(alchemy_sleep_au1550)
+/* sleepcode for Au1300 memory controller type */
+LEAF(alchemy_sleep_au1300)
+
+ SETUP_SLEEP
+
+ /* cache following instructions, as memory gets put to sleep */
+ la t0, 2f
+ la t1, 4f
+ subu t2, t1, t0
+
+ .set mips3
+
+1: cache 0x14, 0(t0)
+ subu t2, t2, 32
+ bgez t2, 1b
+ addu t0, t0, 32
+
+ .set mips0
+
+2: lui a0, 0xb400 /* mem_xxx */
+
+ /* disable all ports in mem_sdportcfga */
+ sw zero, 0x868(a0) /* mem_sdportcfga */
+ sync
+
+ /* disable ODT */
+ li t0, 0x03010000
+ sw t0, 0x08d8(a0) /* mem_sdcmd0 */
+ sw t0, 0x08dc(a0) /* mem_sdcmd1 */
+ sync
+
+ /* precharge */
+ li t0, 0x23000400
+ sw t0, 0x08dc(a0) /* mem_sdcmd1 */
+ sw t0, 0x08d8(a0) /* mem_sdcmd0 */
+ sync
+
+ /* auto refresh */
+ sw zero, 0x08c8(a0) /* mem_sdautoref */
+ sync
+
+ /* block access to the DDR */
+ lw t0, 0x0848(a0) /* mem_sdconfigb */
+ li t1, (1 << 7 | 0x3F)
+ or t0, t0, t1
+ sw t0, 0x0848(a0) /* mem_sdconfigb */
+ sync
+
+ /* issue the Self Refresh command */
+ li t0, 0x10000000
+ sw t0, 0x08dc(a0) /* mem_sdcmd1 */
+ sw t0, 0x08d8(a0) /* mem_sdcmd0 */
+ sync
+
+ /* wait for sdram to enter self-refresh mode */
+ lui t0, 0x0300
+3: lw t1, 0x0850(a0) /* mem_sdstat */
+ and t2, t1, t0
+ bne t2, t0, 3b
+ nop
+
+ /* disable SDRAM clocks */
+ li t0, ~(3<<28)
+ lw t1, 0x0840(a0) /* mem_sdconfiga */
+ and t1, t1, t0 /* clear CE[1:0] */
+ sw t1, 0x0840(a0) /* mem_sdconfiga */
+ sync
+
+ DO_SLEEP
+4:
+
+END(alchemy_sleep_au1300)
+
/* This is where we return upon wakeup.
* Reload all of the registers and return.
diff --git a/arch/mips/alchemy/common/time.c b/arch/mips/alchemy/common/time.c
index d5da6ad..a594a85 100644
--- a/arch/mips/alchemy/common/time.c
+++ b/arch/mips/alchemy/common/time.c
@@ -178,6 +178,7 @@ static int alchemy_m2inttab[] __initdata = {
AU1100_RTC_MATCH2_INT,
AU1550_RTC_MATCH2_INT,
AU1200_RTC_MATCH2_INT,
+ AU1300_RTC_MATCH2_INT,
};
void __init plat_time_init(void)
diff --git a/arch/mips/alchemy/common/vss.c b/arch/mips/alchemy/common/vss.c
new file mode 100644
index 0000000..d23b144
--- /dev/null
+++ b/arch/mips/alchemy/common/vss.c
@@ -0,0 +1,84 @@
+/*
+ * Au1300 media block power gating (VSS)
+ *
+ * This is a stop-gap solution until I have the clock framework integration
+ * ready. This stuff here really must be handled transparently when clocks
+ * for various media blocks are enabled/disabled.
+ */
+
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#define VSS_GATE 0x00 /* gate wait timers */
+#define VSS_CLKRST 0x04 /* clock/block control */
+#define VSS_FTR 0x08 /* footers */
+
+#define VSS_ADDR(blk) (KSEG1ADDR(AU1300_VSS_PHYS_ADDR) + (blk * 0x0c))
+
+static DEFINE_SPINLOCK(au1300_vss_lock);
+
+/* enable a block as outlined in the databook */
+static inline void __enable_block(int block)
+{
+ void __iomem *base = (void __iomem *)VSS_ADDR(block);
+
+ __raw_writel(3, base + VSS_CLKRST); /* enable clock, assert reset */
+ wmb();
+
+ __raw_writel(0x01fffffe, base + VSS_GATE); /* maximum setup time */
+ wmb();
+
+ /* enable footers in sequence */
+ __raw_writel(0x01, base + VSS_FTR);
+ wmb();
+ __raw_writel(0x03, base + VSS_FTR);
+ wmb();
+ __raw_writel(0x07, base + VSS_FTR);
+ wmb();
+ __raw_writel(0x0f, base + VSS_FTR);
+ wmb();
+
+ __raw_writel(0x01ffffff, base + VSS_GATE); /* start FSM too */
+ wmb();
+
+ __raw_writel(2, base + VSS_CLKRST); /* deassert reset */
+ wmb();
+
+ __raw_writel(0x1f, base + VSS_FTR); /* enable isolation cells */
+ wmb();
+}
+
+/* disable a block as outlined in the databook */
+static inline void __disable_block(int block)
+{
+ void __iomem *base = (void __iomem *)VSS_ADDR(block);
+
+ __raw_writel(0x0f, base + VSS_FTR); /* disable isolation cells */
+ wmb();
+ __raw_writel(0, base + VSS_GATE); /* disable FSM */
+ wmb();
+ __raw_writel(3, base + VSS_CLKRST); /* assert reset */
+ wmb();
+ __raw_writel(1, base + VSS_CLKRST); /* disable clock */
+ wmb();
+ __raw_writel(0, base + VSS_FTR); /* disable all footers */
+ wmb();
+}
+
+void au1300_vss_block_control(int block, int enable)
+{
+ unsigned long flags;
+
+ if (alchemy_get_cputype() != ALCHEMY_CPU_AU1300)
+ return;
+
+ /* only one block at a time */
+ spin_lock_irqsave(&au1300_vss_lock, flags);
+ if (enable)
+ __enable_block(block);
+ else
+ __disable_block(block);
+ spin_unlock_irqrestore(&au1300_vss_lock, flags);
+}
+EXPORT_SYMBOL_GPL(au1300_vss_block_control);
diff --git a/arch/mips/include/asm/cpu.h b/arch/mips/include/asm/cpu.h
index 5f95a4b..bb9a470 100644
--- a/arch/mips/include/asm/cpu.h
+++ b/arch/mips/include/asm/cpu.h
@@ -166,6 +166,7 @@
#define PRID_IMP_NETLOGIC_XLS412B 0x4c00
#define PRID_IMP_NETLOGIC_XLS408B 0x4e00
#define PRID_IMP_NETLOGIC_XLS404B 0x4f00
+#define PRID_IMP_NETLOGIC_AU13XX 0x8000
/*
* Definitions for 7:0 on legacy processors
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index de24ec5..65f1262 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -136,6 +136,7 @@ static inline int au1xxx_cpu_needs_config_od(void)
#define ALCHEMY_CPU_AU1100 2
#define ALCHEMY_CPU_AU1550 3
#define ALCHEMY_CPU_AU1200 4
+#define ALCHEMY_CPU_AU1300 5
static inline int alchemy_get_cputype(void)
{
@@ -156,6 +157,9 @@ static inline int alchemy_get_cputype(void)
case 0x05030000:
return ALCHEMY_CPU_AU1200;
break;
+ case 0x800c0000:
+ return ALCHEMY_CPU_AU1300;
+ break;
}
return ALCHEMY_CPU_UNKNOWN;
@@ -166,6 +170,7 @@ static inline int alchemy_get_uarts(int type)
{
switch (type) {
case ALCHEMY_CPU_AU1000:
+ case ALCHEMY_CPU_AU1300:
return 4;
case ALCHEMY_CPU_AU1500:
case ALCHEMY_CPU_AU1200:
@@ -243,6 +248,7 @@ extern unsigned long au1xxx_calc_clock(void);
/* PM: arch/mips/alchemy/common/sleeper.S, power.c, irq.c */
void alchemy_sleep_au1000(void);
void alchemy_sleep_au1550(void);
+void alchemy_sleep_au1300(void);
void au_sleep(void);
/* USB: drivers/usb/host/alchemy-common.c */
@@ -251,6 +257,7 @@ enum alchemy_usb_block {
ALCHEMY_USB_UDC0,
ALCHEMY_USB_EHCI0,
ALCHEMY_USB_OTG0,
+ ALCHEMY_USB_OHCI1,
};
int alchemy_usb_control(int block, int enable);
@@ -263,14 +270,92 @@ struct alchemy_pci_platdata {
unsigned long pci_cfg_clr;
};
-/* SOC Interrupt numbers */
+/* Multifunction pins: Each of these pins can either be assigned to the
+ * GPIO controller or a on-chip peripheral.
+ * Call "au1300_pinfunc_to_dev()" or "au1300_pinfunc_to_gpio()" to
+ * assign one of these to either the GPIO controller or the device.
+ */
+enum au1300_multifunc_pins {
+ /* wake-from-str pins 0-3 */
+ AU1300_PIN_WAKE0 = 0, AU1300_PIN_WAKE1, AU1300_PIN_WAKE2,
+ AU1300_PIN_WAKE3,
+ /* external clock sources for PSCs: 4-5 */
+ AU1300_PIN_EXTCLK0, AU1300_PIN_EXTCLK1,
+ /* 8bit MMC interface on SD0: 6-9 */
+ AU1300_PIN_SD0DAT4, AU1300_PIN_SD0DAT5, AU1300_PIN_SD0DAT6,
+ AU1300_PIN_SD0DAT7,
+ /* aux clk input for freqgen 3: 10 */
+ AU1300_PIN_FG3AUX,
+ /* UART1 pins: 11-18 */
+ AU1300_PIN_U1RI, AU1300_PIN_U1DCD, AU1300_PIN_U1DSR,
+ AU1300_PIN_U1CTS, AU1300_PIN_U1RTS, AU1300_PIN_U1DTR,
+ AU1300_PIN_U1RX, AU1300_PIN_U1TX,
+ /* UART0 pins: 19-24 */
+ AU1300_PIN_U0RI, AU1300_PIN_U0DCD, AU1300_PIN_U0DSR,
+ AU1300_PIN_U0CTS, AU1300_PIN_U0RTS, AU1300_PIN_U0DTR,
+ /* UART2: 25-26 */
+ AU1300_PIN_U2RX, AU1300_PIN_U2TX,
+ /* UART3: 27-28 */
+ AU1300_PIN_U3RX, AU1300_PIN_U3TX,
+ /* LCD controller PWMs, ext pixclock: 29-31 */
+ AU1300_PIN_LCDPWM0, AU1300_PIN_LCDPWM1, AU1300_PIN_LCDCLKIN,
+ /* SD1 interface: 32-37 */
+ AU1300_PIN_SD1DAT0, AU1300_PIN_SD1DAT1, AU1300_PIN_SD1DAT2,
+ AU1300_PIN_SD1DAT3, AU1300_PIN_SD1CMD, AU1300_PIN_SD1CLK,
+ /* SD2 interface: 38-43 */
+ AU1300_PIN_SD2DAT0, AU1300_PIN_SD2DAT1, AU1300_PIN_SD2DAT2,
+ AU1300_PIN_SD2DAT3, AU1300_PIN_SD2CMD, AU1300_PIN_SD2CLK,
+ /* PSC0/1 clocks: 44-45 */
+ AU1300_PIN_PSC0CLK, AU1300_PIN_PSC1CLK,
+ /* PSCs: 46-49/50-53/54-57/58-61 */
+ AU1300_PIN_PSC0SYNC0, AU1300_PIN_PSC0SYNC1, AU1300_PIN_PSC0D0,
+ AU1300_PIN_PSC0D1,
+ AU1300_PIN_PSC1SYNC0, AU1300_PIN_PSC1SYNC1, AU1300_PIN_PSC1D0,
+ AU1300_PIN_PSC1D1,
+ AU1300_PIN_PSC2SYNC0, AU1300_PIN_PSC2SYNC1, AU1300_PIN_PSC2D0,
+ AU1300_PIN_PSC2D1,
+ AU1300_PIN_PSC3SYNC0, AU1300_PIN_PSC3SYNC1, AU1300_PIN_PSC3D0,
+ AU1300_PIN_PSC3D1,
+ /* PCMCIA interface: 62-70 */
+ AU1300_PIN_PCE2, AU1300_PIN_PCE1, AU1300_PIN_PIOS16,
+ AU1300_PIN_PIOR, AU1300_PIN_PWE, AU1300_PIN_PWAIT,
+ AU1300_PIN_PREG, AU1300_PIN_POE, AU1300_PIN_PIOW,
+ /* camera interface H/V sync inputs: 71-72 */
+ AU1300_PIN_CIMLS, AU1300_PIN_CIMFS,
+ /* PSC2/3 clocks: 73-74 */
+ AU1300_PIN_PSC2CLK, AU1300_PIN_PSC3CLK,
+};
+
+/* GPIC (Au1300) pin management: arch/mips/alchemy/common/gpioint.c */
+extern void au1300_pinfunc_to_gpio(enum au1300_multifunc_pins gpio);
+extern void au1300_pinfunc_to_dev(enum au1300_multifunc_pins gpio);
+extern void au1300_set_irq_priority(unsigned int irq, int p);
+extern void au1300_set_dbdma_gpio(int dchan, unsigned int gpio);
+
+/* Au1300 allows to disconnect certain blocks from internal power supply */
+enum au1300_vss_block {
+ AU1300_VSS_MPE = 0,
+ AU1300_VSS_BSA,
+ AU1300_VSS_GPE,
+ AU1300_VSS_MGP,
+};
+
+extern void au1300_vss_block_control(int block, int enable);
+
+/* SOC Interrupt numbers */
+/* Au1000-style (IC0/1): 2 controllers with 32 sources each */
#define AU1000_INTC0_INT_BASE (MIPS_CPU_IRQ_BASE + 8)
#define AU1000_INTC0_INT_LAST (AU1000_INTC0_INT_BASE + 31)
#define AU1000_INTC1_INT_BASE (AU1000_INTC0_INT_LAST + 1)
#define AU1000_INTC1_INT_LAST (AU1000_INTC1_INT_BASE + 31)
#define AU1000_MAX_INTR AU1000_INTC1_INT_LAST
+/* Au1300-style (GPIC): 1 controller with up to 128 sources */
+#define ALCHEMY_GPIC_INT_BASE (MIPS_CPU_IRQ_BASE + 8)
+#define ALCHEMY_GPIC_INT_NUM 128
+#define ALCHEMY_GPIC_INT_LAST (ALCHEMY_GPIC_INT_BASE + ALCHEMY_GPIC_INT_NUM - 1)
+
enum soc_au1000_ints {
AU1000_FIRST_INT = AU1000_INTC0_INT_BASE,
AU1000_UART0_INT = AU1000_FIRST_INT,
@@ -591,24 +676,77 @@ enum soc_au1200_ints {
#endif /* !defined (_LANGUAGE_ASSEMBLY) */
+/* Au1300 peripheral interrupt numbers */
+#define AU1300_FIRST_INT (ALCHEMY_GPIC_INT_BASE)
+#define AU1300_UART1_INT (AU1300_FIRST_INT + 17)
+#define AU1300_UART2_INT (AU1300_FIRST_INT + 25)
+#define AU1300_UART3_INT (AU1300_FIRST_INT + 27)
+#define AU1300_SD1_INT (AU1300_FIRST_INT + 32)
+#define AU1300_SD2_INT (AU1300_FIRST_INT + 38)
+#define AU1300_PSC0_INT (AU1300_FIRST_INT + 48)
+#define AU1300_PSC1_INT (AU1300_FIRST_INT + 52)
+#define AU1300_PSC2_INT (AU1300_FIRST_INT + 56)
+#define AU1300_PSC3_INT (AU1300_FIRST_INT + 60)
+#define AU1300_NAND_INT (AU1300_FIRST_INT + 62)
+#define AU1300_DDMA_INT (AU1300_FIRST_INT + 75)
+#define AU1300_MMU_INT (AU1300_FIRST_INT + 76)
+#define AU1300_MPU_INT (AU1300_FIRST_INT + 77)
+#define AU1300_GPU_INT (AU1300_FIRST_INT + 78)
+#define AU1300_UDMA_INT (AU1300_FIRST_INT + 79)
+#define AU1300_TOY_INT (AU1300_FIRST_INT + 80)
+#define AU1300_TOY_MATCH0_INT (AU1300_FIRST_INT + 81)
+#define AU1300_TOY_MATCH1_INT (AU1300_FIRST_INT + 82)
+#define AU1300_TOY_MATCH2_INT (AU1300_FIRST_INT + 83)
+#define AU1300_RTC_INT (AU1300_FIRST_INT + 84)
+#define AU1300_RTC_MATCH0_INT (AU1300_FIRST_INT + 85)
+#define AU1300_RTC_MATCH1_INT (AU1300_FIRST_INT + 86)
+#define AU1300_RTC_MATCH2_INT (AU1300_FIRST_INT + 87)
+#define AU1300_UART0_INT (AU1300_FIRST_INT + 88)
+#define AU1300_SD0_INT (AU1300_FIRST_INT + 89)
+#define AU1300_USB_INT (AU1300_FIRST_INT + 90)
+#define AU1300_LCD_INT (AU1300_FIRST_INT + 91)
+#define AU1300_BSA_INT (AU1300_FIRST_INT + 92)
+#define AU1300_MPE_INT (AU1300_FIRST_INT + 93)
+#define AU1300_ITE_INT (AU1300_FIRST_INT + 94)
+#define AU1300_AES_INT (AU1300_FIRST_INT + 95)
+#define AU1300_CIM_INT (AU1300_FIRST_INT + 96)
+
+/**********************************************************************/
+
/*
* Physical base addresses for integrated peripherals
- * 0..au1000 1..au1500 2..au1100 3..au1550 4..au1200
+ * 0..au1000 1..au1500 2..au1100 3..au1550 4..au1200 5..au1300
*/
#define AU1000_AC97_PHYS_ADDR 0x10000000 /* 012 */
+#define AU1300_ROM_PHYS_ADDR 0x10000000 /* 5 */
+#define AU1300_OTP_PHYS_ADDR 0x10002000 /* 5 */
+#define AU1300_VSS_PHYS_ADDR 0x10003000 /* 5 */
+#define AU1300_UART0_PHYS_ADDR 0x10100000 /* 5 */
+#define AU1300_UART1_PHYS_ADDR 0x10101000 /* 5 */
+#define AU1300_UART2_PHYS_ADDR 0x10102000 /* 5 */
+#define AU1300_UART3_PHYS_ADDR 0x10103000 /* 5 */
#define AU1000_USB_OHCI_PHYS_ADDR 0x10100000 /* 012 */
#define AU1000_USB_UDC_PHYS_ADDR 0x10200000 /* 0123 */
+#define AU1300_GPIC_PHYS_ADDR 0x10200000 /* 5 */
#define AU1000_IRDA_PHYS_ADDR 0x10300000 /* 02 */
-#define AU1200_AES_PHYS_ADDR 0x10300000 /* 4 */
+#define AU1200_AES_PHYS_ADDR 0x10300000 /* 45 */
#define AU1000_IC0_PHYS_ADDR 0x10400000 /* 01234 */
+#define AU1300_GPU_PHYS_ADDR 0x10500000 /* 5 */
#define AU1000_MAC0_PHYS_ADDR 0x10500000 /* 023 */
#define AU1000_MAC1_PHYS_ADDR 0x10510000 /* 023 */
#define AU1000_MACEN_PHYS_ADDR 0x10520000 /* 023 */
-#define AU1100_SD0_PHYS_ADDR 0x10600000 /* 24 */
+#define AU1100_SD0_PHYS_ADDR 0x10600000 /* 245 */
+#define AU1300_SD1_PHYS_ADDR 0x10601000 /* 5 */
+#define AU1300_SD2_PHYS_ADDR 0x10602000 /* 5 */
#define AU1100_SD1_PHYS_ADDR 0x10680000 /* 24 */
+#define AU1300_SYS_PHYS_ADDR 0x10900000 /* 5 */
#define AU1550_PSC2_PHYS_ADDR 0x10A00000 /* 3 */
#define AU1550_PSC3_PHYS_ADDR 0x10B00000 /* 3 */
+#define AU1300_PSC0_PHYS_ADDR 0x10A00000 /* 5 */
+#define AU1300_PSC1_PHYS_ADDR 0x10A01000 /* 5 */
+#define AU1300_PSC2_PHYS_ADDR 0x10A02000 /* 5 */
+#define AU1300_PSC3_PHYS_ADDR 0x10A03000 /* 5 */
#define AU1000_I2S_PHYS_ADDR 0x11000000 /* 02 */
#define AU1500_MAC0_PHYS_ADDR 0x11500000 /* 1 */
#define AU1500_MAC1_PHYS_ADDR 0x11510000 /* 1 */
@@ -622,38 +760,97 @@ enum soc_au1200_ints {
#define AU1000_SSI1_PHYS_ADDR 0x11680000 /* 02 */
#define AU1500_GPIO2_PHYS_ADDR 0x11700000 /* 1234 */
#define AU1000_IC1_PHYS_ADDR 0x11800000 /* 01234 */
-#define AU1000_SYS_PHYS_ADDR 0x11900000 /* 01234 */
+#define AU1000_SYS_PHYS_ADDR 0x11900000 /* 012345 */
#define AU1550_PSC0_PHYS_ADDR 0x11A00000 /* 34 */
#define AU1550_PSC1_PHYS_ADDR 0x11B00000 /* 34 */
#define AU1000_MEM_PHYS_ADDR 0x14000000 /* 01234 */
#define AU1000_STATIC_MEM_PHYS_ADDR 0x14001000 /* 01234 */
+#define AU1300_UDMA_PHYS_ADDR 0x14001800 /* 5 */
#define AU1000_DMA_PHYS_ADDR 0x14002000 /* 012 */
-#define AU1550_DBDMA_PHYS_ADDR 0x14002000 /* 34 */
-#define AU1550_DBDMA_CONF_PHYS_ADDR 0x14003000 /* 34 */
+#define AU1550_DBDMA_PHYS_ADDR 0x14002000 /* 345 */
+#define AU1550_DBDMA_CONF_PHYS_ADDR 0x14003000 /* 345 */
#define AU1000_MACDMA0_PHYS_ADDR 0x14004000 /* 0123 */
#define AU1000_MACDMA1_PHYS_ADDR 0x14004200 /* 0123 */
-#define AU1200_CIM_PHYS_ADDR 0x14004000 /* 4 */
+#define AU1200_CIM_PHYS_ADDR 0x14004000 /* 45 */
#define AU1500_PCI_PHYS_ADDR 0x14005000 /* 13 */
#define AU1550_PE_PHYS_ADDR 0x14008000 /* 3 */
#define AU1200_MAEBE_PHYS_ADDR 0x14010000 /* 4 */
#define AU1200_MAEFE_PHYS_ADDR 0x14012000 /* 4 */
+#define AU1300_MAEITE_PHYS_ADDR 0x14010000 /* 5 */
+#define AU1300_MAEMPE_PHYS_ADDR 0x14014000 /* 5 */
#define AU1550_USB_OHCI_PHYS_ADDR 0x14020000 /* 3 */
#define AU1200_USB_CTL_PHYS_ADDR 0x14020000 /* 4 */
#define AU1200_USB_OTG_PHYS_ADDR 0x14020020 /* 4 */
#define AU1200_USB_OHCI_PHYS_ADDR 0x14020100 /* 4 */
#define AU1200_USB_EHCI_PHYS_ADDR 0x14020200 /* 4 */
#define AU1200_USB_UDC_PHYS_ADDR 0x14022000 /* 4 */
+#define AU1300_USB_EHCI_PHYS_ADDR 0x14020000 /* 5 */
+#define AU1300_USB_OHCI0_PHYS_ADDR 0x14020400 /* 5 */
+#define AU1300_USB_OHCI1_PHYS_ADDR 0x14020800 /* 5 */
+#define AU1300_USB_CTL_PHYS_ADDR 0x14021000 /* 5 */
+#define AU1300_USB_OTG_PHYS_ADDR 0x14022000 /* 5 */
+#define AU1300_MAEBSA_PHYS_ADDR 0x14030000 /* 5 */
#define AU1100_LCD_PHYS_ADDR 0x15000000 /* 2 */
-#define AU1200_LCD_PHYS_ADDR 0x15000000 /* 4 */
+#define AU1200_LCD_PHYS_ADDR 0x15000000 /* 45 */
#define AU1500_PCI_MEM_PHYS_ADDR 0x400000000ULL /* 13 */
#define AU1500_PCI_IO_PHYS_ADDR 0x500000000ULL /* 13 */
#define AU1500_PCI_CONFIG0_PHYS_ADDR 0x600000000ULL /* 13 */
#define AU1500_PCI_CONFIG1_PHYS_ADDR 0x680000000ULL /* 13 */
-#define AU1000_PCMCIA_IO_PHYS_ADDR 0xF00000000ULL /* 01234 */
-#define AU1000_PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL /* 01234 */
-#define AU1000_PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL /* 01234 */
+#define AU1000_PCMCIA_IO_PHYS_ADDR 0xF00000000ULL /* 012345 */
+#define AU1000_PCMCIA_ATTR_PHYS_ADDR 0xF40000000ULL /* 012345 */
+#define AU1000_PCMCIA_MEM_PHYS_ADDR 0xF80000000ULL /* 012345 */
+
+/**********************************************************************/
+/*
+ * Au1300 GPIO+INT controller (GPIC) register offsets and bits
+ * Registers are 128bits (0x10 bytes), divided into 4 "banks".
+ */
+#define AU1300_GPIC_PINVAL 0x0000
+#define AU1300_GPIC_PINVALCLR 0x0010
+#define AU1300_GPIC_IPEND 0x0020
+#define AU1300_GPIC_PRIENC 0x0030
+#define AU1300_GPIC_IEN 0x0040 /* int_mask in manual */
+#define AU1300_GPIC_IDIS 0x0050 /* int_maskclr in manual */
+#define AU1300_GPIC_DMASEL 0x0060
+#define AU1300_GPIC_DEVSEL 0x0080
+#define AU1300_GPIC_DEVCLR 0x0090
+#define AU1300_GPIC_RSTVAL 0x00a0
+/* pin configuration space. one 32bit register for up to 128 IRQs */
+#define AU1300_GPIC_PINCFG 0x1000
+
+#define GPIC_GPIO_TO_BIT(gpio) \
+ (1 << ((gpio) & 0x1f))
+
+#define GPIC_GPIO_BANKOFF(gpio) \
+ (((gpio) >> 5) * 4)
+
+/* Pin Control bits: who owns the pin, what does it do */
+#define GPIC_CFG_PC_GPIN 0
+#define GPIC_CFG_PC_DEV 1
+#define GPIC_CFG_PC_GPOLOW 2
+#define GPIC_CFG_PC_GPOHIGH 3
+#define GPIC_CFG_PC_MASK 3
+
+/* assign pin to MIPS IRQ line */
+#define GPIC_CFG_IL_SET(x) (((x) & 3) << 2)
+#define GPIC_CFG_IL_MASK (3 << 2)
+
+/* pin interrupt type setup */
+#define GPIC_CFG_IC_OFF (0 << 4)
+#define GPIC_CFG_IC_LEVEL_LOW (1 << 4)
+#define GPIC_CFG_IC_LEVEL_HIGH (2 << 4)
+#define GPIC_CFG_IC_EDGE_FALL (5 << 4)
+#define GPIC_CFG_IC_EDGE_RISE (6 << 4)
+#define GPIC_CFG_IC_EDGE_BOTH (7 << 4)
+#define GPIC_CFG_IC_MASK (7 << 4)
+
+/* allow interrupt to wake cpu from 'wait' */
+#define GPIC_CFG_IDLEWAKE (1 << 7)
+
+/***********************************************************************/
+
/* Au1000 SDRAM memory controller register offsets */
#define AU1000_MEM_SDMODE0 0x0000
#define AU1000_MEM_SDMODE1 0x0004
diff --git a/arch/mips/include/asm/mach-au1x00/au1100_mmc.h b/arch/mips/include/asm/mach-au1x00/au1100_mmc.h
index 94000a3..e221659 100644
--- a/arch/mips/include/asm/mach-au1x00/au1100_mmc.h
+++ b/arch/mips/include/asm/mach-au1x00/au1100_mmc.h
@@ -130,8 +130,10 @@ struct au1xmmc_platform_data {
#define SD_CONFIG2_DF (0x00000008)
#define SD_CONFIG2_DC (0x00000010)
#define SD_CONFIG2_xx2 (0x000000e0)
+#define SD_CONFIG2_BB (0x00000080)
#define SD_CONFIG2_WB (0x00000100)
#define SD_CONFIG2_RW (0x00000200)
+#define SD_CONFIG2_DP (0x00000400)
/*
diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h b/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h
index 323ce2d..217810e 100644
--- a/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h
+++ b/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h
@@ -183,6 +183,37 @@ typedef volatile struct au1xxx_ddma_desc {
#define AU1200_DSCR_CMD0_PSC1_SYNC 25
#define AU1200_DSCR_CMD0_CIM_SYNC 26
+#define AU1300_DSCR_CMD0_UART0_TX 0
+#define AU1300_DSCR_CMD0_UART0_RX 1
+#define AU1300_DSCR_CMD0_UART1_TX 2
+#define AU1300_DSCR_CMD0_UART1_RX 3
+#define AU1300_DSCR_CMD0_UART2_TX 4
+#define AU1300_DSCR_CMD0_UART2_RX 5
+#define AU1300_DSCR_CMD0_UART3_TX 6
+#define AU1300_DSCR_CMD0_UART3_RX 7
+#define AU1300_DSCR_CMD0_SDMS_TX0 8
+#define AU1300_DSCR_CMD0_SDMS_RX0 9
+#define AU1300_DSCR_CMD0_SDMS_TX1 10
+#define AU1300_DSCR_CMD0_SDMS_RX1 11
+#define AU1300_DSCR_CMD0_AES_TX 12
+#define AU1300_DSCR_CMD0_AES_RX 13
+#define AU1300_DSCR_CMD0_PSC0_TX 14
+#define AU1300_DSCR_CMD0_PSC0_RX 15
+#define AU1300_DSCR_CMD0_PSC1_TX 16
+#define AU1300_DSCR_CMD0_PSC1_RX 17
+#define AU1300_DSCR_CMD0_PSC2_TX 18
+#define AU1300_DSCR_CMD0_PSC2_RX 19
+#define AU1300_DSCR_CMD0_PSC3_TX 20
+#define AU1300_DSCR_CMD0_PSC3_RX 21
+#define AU1300_DSCR_CMD0_LCD 22
+#define AU1300_DSCR_CMD0_NAND_FLASH 23
+#define AU1300_DSCR_CMD0_SDMS_TX2 24
+#define AU1300_DSCR_CMD0_SDMS_RX2 25
+#define AU1300_DSCR_CMD0_CIM_SYNC 26
+#define AU1300_DSCR_CMD0_UDMA 27
+#define AU1300_DSCR_CMD0_DMA_REQ0 28
+#define AU1300_DSCR_CMD0_DMA_REQ1 29
+
#define DSCR_CMD0_THROTTLE 30
#define DSCR_CMD0_ALWAYS 31
#define DSCR_NDEV_IDS 32
diff --git a/arch/mips/include/asm/mach-au1x00/gpio-au1300.h b/arch/mips/include/asm/mach-au1x00/gpio-au1300.h
new file mode 100644
index 0000000..556e1be
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/gpio-au1300.h
@@ -0,0 +1,241 @@
+/*
+ * gpio-au1300.h -- GPIO control for Au1300 GPIC and compatibles.
+ *
+ * Copyright (c) 2009-2011 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#ifndef _GPIO_AU1300_H_
+#define _GPIO_AU1300_H_
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/* with the current GPIC design, up to 128 GPIOs are possible.
+ * The only implementation so far is in the Au1300, which has 75 externally
+ * available GPIOs.
+ */
+#define AU1300_GPIO_BASE 0
+#define AU1300_GPIO_NUM 75
+#define AU1300_GPIO_MAX (AU1300_GPIO_BASE + AU1300_GPIO_NUM - 1)
+
+#define AU1300_GPIC_ADDR \
+ (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR)
+
+static inline int au1300_gpio_get_value(unsigned int gpio)
+{
+ void __iomem *roff = AU1300_GPIC_ADDR;
+ int bit;
+
+ gpio -= AU1300_GPIO_BASE;
+ roff += GPIC_GPIO_BANKOFF(gpio);
+ bit = GPIC_GPIO_TO_BIT(gpio);
+ return __raw_readl(roff + AU1300_GPIC_PINVAL) & bit;
+}
+
+static inline int au1300_gpio_direction_input(unsigned int gpio)
+{
+ void __iomem *roff = AU1300_GPIC_ADDR;
+ unsigned long bit;
+
+ gpio -= AU1300_GPIO_BASE;
+
+ roff += GPIC_GPIO_BANKOFF(gpio);
+ bit = GPIC_GPIO_TO_BIT(gpio);
+ __raw_writel(bit, roff + AU1300_GPIC_DEVCLR);
+ wmb();
+
+ return 0;
+}
+
+static inline int au1300_gpio_set_value(unsigned int gpio, int v)
+{
+ void __iomem *roff = AU1300_GPIC_ADDR;
+ unsigned long bit;
+
+ gpio -= AU1300_GPIO_BASE;
+
+ roff += GPIC_GPIO_BANKOFF(gpio);
+ bit = GPIC_GPIO_TO_BIT(gpio);
+ __raw_writel(bit, roff + (v ? AU1300_GPIC_PINVAL
+ : AU1300_GPIC_PINVALCLR));
+ wmb();
+
+ return 0;
+}
+
+static inline int au1300_gpio_direction_output(unsigned int gpio, int v)
+{
+ /* hw switches to output automatically */
+ return au1300_gpio_set_value(gpio, v);
+}
+
+static inline int au1300_gpio_to_irq(unsigned int gpio)
+{
+ return AU1300_FIRST_INT + (gpio - AU1300_GPIO_BASE);
+}
+
+static inline int au1300_irq_to_gpio(unsigned int irq)
+{
+ return (irq - AU1300_FIRST_INT) + AU1300_GPIO_BASE;
+}
+
+static inline int au1300_gpio_is_valid(unsigned int gpio)
+{
+ int ret;
+
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1300:
+ ret = ((gpio >= AU1300_GPIO_BASE) && (gpio <= AU1300_GPIO_MAX));
+ break;
+ default:
+ ret = 0;
+ }
+ return ret;
+}
+
+static inline int au1300_gpio_cansleep(unsigned int gpio)
+{
+ return 0;
+}
+
+/* hardware remembers gpio 0-63 levels on powerup */
+static inline int au1300_gpio_getinitlvl(unsigned int gpio)
+{
+ void __iomem *roff = AU1300_GPIC_ADDR;
+ unsigned long v;
+
+ if (unlikely(gpio > 63))
+ return 0;
+ else if (gpio > 31) {
+ gpio -= 32;
+ roff += 4;
+ }
+
+ v = __raw_readl(roff + AU1300_GPIC_RSTVAL);
+ return (v >> gpio) & 1;
+}
+
+/**********************************************************************/
+
+/* Linux gpio framework integration.
+*
+* 4 use cases of Alchemy GPIOS:
+*(1) GPIOLIB=y, ALCHEMY_GPIO_INDIRECT=y:
+* Board must register gpiochips.
+*(2) GPIOLIB=y, ALCHEMY_GPIO_INDIRECT=n:
+* A gpiochip for the 75 GPIOs is registered.
+*
+*(3) GPIOLIB=n, ALCHEMY_GPIO_INDIRECT=y:
+* the boards' gpio.h must provide the linux gpio wrapper functions,
+*
+*(4) GPIOLIB=n, ALCHEMY_GPIO_INDIRECT=n:
+* inlinable gpio functions are provided which enable access to the
+* Au1300 gpios only by using the numbers straight out of the data-
+* sheets.
+
+* Cases 1 and 3 are intended for boards which want to provide their own
+* GPIO namespace and -operations (i.e. for example you have 8 GPIOs
+* which are in part provided by spare Au1300 GPIO pins and in part by
+* an external FPGA but you still want them to be accssible in linux
+* as gpio0-7. The board can of course use the alchemy_gpioX_* functions
+* as required).
+*/
+
+#ifndef CONFIG_GPIOLIB
+
+#ifdef CONFIG_ALCHEMY_GPIOINT_AU1300
+
+#ifndef CONFIG_ALCHEMY_GPIO_INDIRECT /* case (4) */
+
+static inline int gpio_direction_input(unsigned int gpio)
+{
+ return au1300_gpio_direction_input(gpio);
+}
+
+static inline int gpio_direction_output(unsigned int gpio, int v)
+{
+ return au1300_gpio_direction_output(gpio, v);
+}
+
+static inline int gpio_get_value(unsigned int gpio)
+{
+ return au1300_gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value(unsigned int gpio, int v)
+{
+ au1300_gpio_set_value(gpio, v);
+}
+
+static inline int gpio_get_value_cansleep(unsigned gpio)
+{
+ return gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value_cansleep(unsigned gpio, int value)
+{
+ gpio_set_value(gpio, value);
+}
+
+static inline int gpio_is_valid(unsigned int gpio)
+{
+ return au1300_gpio_is_valid(gpio);
+}
+
+static inline int gpio_cansleep(unsigned int gpio)
+{
+ return au1300_gpio_cansleep(gpio);
+}
+
+static inline int gpio_to_irq(unsigned int gpio)
+{
+ return au1300_gpio_to_irq(gpio);
+}
+
+static inline int irq_to_gpio(unsigned int irq)
+{
+ return au1300_irq_to_gpio(irq);
+}
+
+static inline int gpio_request(unsigned int gpio, const char *label)
+{
+ return 0;
+}
+
+static inline void gpio_free(unsigned int gpio)
+{
+}
+
+static inline int gpio_set_debounce(unsigned gpio, unsigned debounce)
+{
+ return -ENOSYS;
+}
+
+static inline void gpio_unexport(unsigned gpio)
+{
+}
+
+static inline int gpio_export(unsigned gpio, bool direction_may_change)
+{
+ return -ENOSYS;
+}
+
+static inline int gpio_sysfs_set_active_low(unsigned gpio, int value)
+{
+ return -ENOSYS;
+}
+
+static inline int gpio_export_link(struct device *dev, const char *name,
+ unsigned gpio)
+{
+ return -ENOSYS;
+}
+
+#endif /* !CONFIG_ALCHEMY_GPIO_INDIRECT */
+
+#endif /* CONFIG_ALCHEMY_GPIOINT_AU1300 */
+
+#endif /* CONFIG GPIOLIB */
+
+#endif /* _GPIO_AU1300_H_ */
diff --git a/arch/mips/include/asm/mach-au1x00/gpio.h b/arch/mips/include/asm/mach-au1x00/gpio.h
index fcdc8c4..22e7ff1 100644
--- a/arch/mips/include/asm/mach-au1x00/gpio.h
+++ b/arch/mips/include/asm/mach-au1x00/gpio.h
@@ -12,6 +12,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
/* On Au1000, Au1500 and Au1100 GPIOs won't work as inputs before
* SYS_PININPUTEN is written to at least once. On Au1550/Au1200/Au1300 this
@@ -58,6 +59,8 @@ static inline int __au_irq_to_gpio(unsigned int irq)
switch (alchemy_get_cputype()) {
case ALCHEMY_CPU_AU1000...ALCHEMY_CPU_AU1200:
return alchemy_irq_to_gpio(irq);
+ case ALCHEMY_CPU_AU1300:
+ return au1300_irq_to_gpio(irq);
}
return -EINVAL;
}
diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c
index ebc0cd2..952dd89 100644
--- a/arch/mips/kernel/cpu-probe.c
+++ b/arch/mips/kernel/cpu-probe.c
@@ -1010,6 +1010,13 @@ static inline void cpu_probe_netlogic(struct cpuinfo_mips *c, int cpu)
{
decode_configs(c);
+ if ((c->processor_id & 0xff00) == PRID_IMP_NETLOGIC_AU13XX) {
+ c->cputype = CPU_ALCHEMY;
+ __cpu_name[cpu] = "Au1300";
+ /* following stuff is not for Alchemy */
+ return;
+ }
+
c->options = (MIPS_CPU_TLB |
MIPS_CPU_4KEX |
MIPS_CPU_COUNTER |
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 6463c4b..c080828 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -300,11 +300,11 @@ config I2C_AT91
unless your system can cope with those limitations.
config I2C_AU1550
- tristate "Au1550/Au1200 SMBus interface"
+ tristate "Au1550/Au1200/Au1300 SMBus interface"
depends on MIPS_ALCHEMY
help
If you say yes to this option, support will be included for the
- Au1550 and Au1200 SMBus interface.
+ Au1550/Au1200/Au1300 SMBus interface.
This driver can also be built as a module. If so, the module
will be called i2c-au1550.
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c
index c8653aa..4c06a3b 100644
--- a/drivers/mmc/host/au1xmmc.c
+++ b/drivers/mmc/host/au1xmmc.c
@@ -153,6 +153,7 @@ static inline int has_dbdma(void)
{
switch (alchemy_get_cputype()) {
case ALCHEMY_CPU_AU1200:
+ case ALCHEMY_CPU_AU1300:
return 1;
default:
return 0;
@@ -768,11 +769,15 @@ static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
config2 = au_readl(HOST_CONFIG2(host));
switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_8:
+ config2 |= SD_CONFIG2_BB;
+ break;
case MMC_BUS_WIDTH_4:
+ config2 &= ~SD_CONFIG2_BB;
config2 |= SD_CONFIG2_WB;
break;
case MMC_BUS_WIDTH_1:
- config2 &= ~SD_CONFIG2_WB;
+ config2 &= ~(SD_CONFIG2_WB | SD_CONFIG2_BB);
break;
}
au_writel(config2, HOST_CONFIG2(host));
@@ -943,7 +948,7 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev)
struct mmc_host *mmc;
struct au1xmmc_host *host;
struct resource *r;
- int ret;
+ int ret, iflag;
mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
if (!mmc) {
@@ -982,37 +987,43 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev)
dev_err(&pdev->dev, "no IRQ defined\n");
goto out3;
}
-
host->irq = r->start;
- /* IRQ is shared among both SD controllers */
- ret = request_irq(host->irq, au1xmmc_irq, IRQF_SHARED,
- DRIVER_NAME, host);
- if (ret) {
- dev_err(&pdev->dev, "cannot grab IRQ\n");
- goto out3;
- }
mmc->ops = &au1xmmc_ops;
mmc->f_min = 450000;
mmc->f_max = 24000000;
+ mmc->max_blk_size = 2048;
+ mmc->max_blk_count = 512;
+
+ mmc->ocr_avail = AU1XMMC_OCR;
+ mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+ mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
+
+ iflag = IRQF_SHARED; /* Au1100/Au1200: one int for both ctrls */
+
switch (alchemy_get_cputype()) {
case ALCHEMY_CPU_AU1100:
mmc->max_seg_size = AU1100_MMC_DESCRIPTOR_SIZE;
- mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
break;
case ALCHEMY_CPU_AU1200:
mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
- mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
+ break;
+ case ALCHEMY_CPU_AU1300:
+ iflag = 0; /* nothing is shared */
+ mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
+ mmc->f_max = 52000000;
+ if (host->ioarea->start == AU1100_SD0_PHYS_ADDR)
+ mmc->caps |= MMC_CAP_8_BIT_DATA;
break;
}
- mmc->max_blk_size = 2048;
- mmc->max_blk_count = 512;
-
- mmc->ocr_avail = AU1XMMC_OCR;
- mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+ ret = request_irq(host->irq, au1xmmc_irq, iflag, DRIVER_NAME, host);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot grab IRQ\n");
+ goto out3;
+ }
host->status = HOST_S_IDLE;
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a1fd73d..369e092 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -87,12 +87,12 @@ config SPI_BFIN_SPORT
Enable support for a SPI bus via the Blackfin SPORT peripheral.
config SPI_AU1550
- tristate "Au1550/Au12x0 SPI Controller"
+ tristate "Au1550/Au1200/Au1300 SPI Controller"
depends on MIPS_ALCHEMY && EXPERIMENTAL
select SPI_BITBANG
help
If you say yes to this option, support will be included for the
- Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
+ PSC SPI controller found on Au1550, Au1200 and Au1300 series.
config SPI_BITBANG
tristate "Utilities for Bitbanging SPI masters"
diff --git a/drivers/usb/host/alchemy-common.c b/drivers/usb/host/alchemy-common.c
index b4192c9..936af83 100644
--- a/drivers/usb/host/alchemy-common.c
+++ b/drivers/usb/host/alchemy-common.c
@@ -52,9 +52,263 @@
USBCFG_EBE | USBCFG_EME | USBCFG_OBE | \
USBCFG_OME)
+/* Au1300 USB config registers */
+#define USB_DWC_CTRL1 0x00
+#define USB_DWC_CTRL2 0x04
+#define USB_VBUS_TIMER 0x10
+#define USB_SBUS_CTRL 0x14
+#define USB_MSR_ERR 0x18
+#define USB_DWC_CTRL3 0x1C
+#define USB_DWC_CTRL4 0x20
+#define USB_OTG_STATUS 0x28
+#define USB_DWC_CTRL5 0x2C
+#define USB_DWC_CTRL6 0x30
+#define USB_DWC_CTRL7 0x34
+#define USB_PHY_STATUS 0xC0
+#define USB_INT_STATUS 0xC4
+#define USB_INT_ENABLE 0xC8
+
+#define USB_DWC_CTRL1_OTGD 0x04 /* set to DISable OTG */
+#define USB_DWC_CTRL1_HSTRS 0x02 /* set to ENable EHCI */
+#define USB_DWC_CTRL1_DCRS 0x01 /* set to ENable UDC */
+
+#define USB_DWC_CTRL2_PHY1RS 0x04 /* set to enable PHY1 */
+#define USB_DWC_CTRL2_PHY0RS 0x02 /* set to enable PHY0 */
+#define USB_DWC_CTRL2_PHYRS 0x01 /* set to enable PHY */
+
+#define USB_DWC_CTRL3_OHCI1_CKEN (1 << 19)
+#define USB_DWC_CTRL3_OHCI0_CKEN (1 << 18)
+#define USB_DWC_CTRL3_EHCI0_CKEN (1 << 17)
+#define USB_DWC_CTRL3_OTG0_CKEN (1 << 16)
+
+#define USB_SBUS_CTRL_SBCA 0x04 /* coherent access */
+
+#define USB_INTEN_FORCE 0x20
+#define USB_INTEN_PHY 0x10
+#define USB_INTEN_UDC 0x08
+#define USB_INTEN_EHCI 0x04
+#define USB_INTEN_OHCI1 0x02
+#define USB_INTEN_OHCI0 0x01
static DEFINE_SPINLOCK(alchemy_usb_lock);
+static inline void __au1300_usb_phyctl(void __iomem *base, int enable)
+{
+ unsigned long r, s;
+
+ r = __raw_readl(base + USB_DWC_CTRL2);
+ s = __raw_readl(base + USB_DWC_CTRL3);
+
+ s &= USB_DWC_CTRL3_OHCI1_CKEN | USB_DWC_CTRL3_OHCI0_CKEN |
+ USB_DWC_CTRL3_EHCI0_CKEN | USB_DWC_CTRL3_OTG0_CKEN;
+
+ if (enable) {
+ /* simply enable all PHYs */
+ r |= USB_DWC_CTRL2_PHY1RS | USB_DWC_CTRL2_PHY0RS |
+ USB_DWC_CTRL2_PHYRS;
+ __raw_writel(r, base + USB_DWC_CTRL2);
+ wmb();
+ } else if (!s) {
+ /* no USB block active, do disable all PHYs */
+ r &= ~(USB_DWC_CTRL2_PHY1RS | USB_DWC_CTRL2_PHY0RS |
+ USB_DWC_CTRL2_PHYRS);
+ __raw_writel(r, base + USB_DWC_CTRL2);
+ wmb();
+ }
+}
+
+static inline void __au1300_ohci_control(void __iomem *base, int enable, int id)
+{
+ unsigned long r;
+
+ if (enable) {
+ __raw_writel(1, base + USB_DWC_CTRL7); /* start OHCI clock */
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL3); /* enable OHCI block */
+ r |= (id == 0) ? USB_DWC_CTRL3_OHCI0_CKEN
+ : USB_DWC_CTRL3_OHCI1_CKEN;
+ __raw_writel(r, base + USB_DWC_CTRL3);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable); /* power up the PHYs */
+
+ r = __raw_readl(base + USB_INT_ENABLE);
+ r |= (id == 0) ? USB_INTEN_OHCI0 : USB_INTEN_OHCI1;
+ __raw_writel(r, base + USB_INT_ENABLE);
+ wmb();
+
+ /* reset the OHCI start clock bit */
+ __raw_writel(0, base + USB_DWC_CTRL7);
+ wmb();
+ } else {
+ r = __raw_readl(base + USB_INT_ENABLE);
+ r &= ~((id == 0) ? USB_INTEN_OHCI0 : USB_INTEN_OHCI1);
+ __raw_writel(r, base + USB_INT_ENABLE);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL3);
+ r &= ~((id == 0) ? USB_DWC_CTRL3_OHCI0_CKEN
+ : USB_DWC_CTRL3_OHCI1_CKEN);
+ __raw_writel(r, base + USB_DWC_CTRL3);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+ }
+}
+
+static inline void __au1300_ehci_control(void __iomem *base, int enable)
+{
+ unsigned long r;
+
+ if (enable) {
+ r = __raw_readl(base + USB_DWC_CTRL3);
+ r |= USB_DWC_CTRL3_EHCI0_CKEN;
+ __raw_writel(r, base + USB_DWC_CTRL3);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL1);
+ r |= USB_DWC_CTRL1_HSTRS;
+ __raw_writel(r, base + USB_DWC_CTRL1);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+
+ r = __raw_readl(base + USB_INT_ENABLE);
+ r |= USB_INTEN_EHCI;
+ __raw_writel(r, base + USB_INT_ENABLE);
+ wmb();
+ } else {
+ r = __raw_readl(base + USB_INT_ENABLE);
+ r &= ~USB_INTEN_EHCI;
+ __raw_writel(r, base + USB_INT_ENABLE);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL1);
+ r &= ~USB_DWC_CTRL1_HSTRS;
+ __raw_writel(r, base + USB_DWC_CTRL1);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL3);
+ r &= ~USB_DWC_CTRL3_EHCI0_CKEN;
+ __raw_writel(r, base + USB_DWC_CTRL3);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+ }
+}
+
+static inline void __au1300_udc_control(void __iomem *base, int enable)
+{
+ unsigned long r;
+
+ if (enable) {
+ r = __raw_readl(base + USB_DWC_CTRL1);
+ r |= USB_DWC_CTRL1_DCRS;
+ __raw_writel(r, base + USB_DWC_CTRL1);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+
+ r = __raw_readl(base + USB_INT_ENABLE);
+ r |= USB_INTEN_UDC;
+ __raw_writel(r, base + USB_INT_ENABLE);
+ wmb();
+ } else {
+ r = __raw_readl(base + USB_INT_ENABLE);
+ r &= ~USB_INTEN_UDC;
+ __raw_writel(r, base + USB_INT_ENABLE);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL1);
+ r &= ~USB_DWC_CTRL1_DCRS;
+ __raw_writel(r, base + USB_DWC_CTRL1);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+ }
+}
+
+static inline void __au1300_otg_control(void __iomem *base, int enable)
+{
+ unsigned long r;
+ if (enable) {
+ r = __raw_readl(base + USB_DWC_CTRL3);
+ r |= USB_DWC_CTRL3_OTG0_CKEN;
+ __raw_writel(r, base + USB_DWC_CTRL3);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL1);
+ r &= ~USB_DWC_CTRL1_OTGD;
+ __raw_writel(r, base + USB_DWC_CTRL1);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+ } else {
+ r = __raw_readl(base + USB_DWC_CTRL1);
+ r |= USB_DWC_CTRL1_OTGD;
+ __raw_writel(r, base + USB_DWC_CTRL1);
+ wmb();
+
+ r = __raw_readl(base + USB_DWC_CTRL3);
+ r &= ~USB_DWC_CTRL3_OTG0_CKEN;
+ __raw_writel(r, base + USB_DWC_CTRL3);
+ wmb();
+
+ __au1300_usb_phyctl(base, enable);
+ }
+}
+
+static inline int au1300_usb_control(int block, int enable)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+ int ret = 0;
+
+ switch (block) {
+ case ALCHEMY_USB_OHCI0:
+ __au1300_ohci_control(base, enable, 0);
+ break;
+ case ALCHEMY_USB_OHCI1:
+ __au1300_ohci_control(base, enable, 1);
+ break;
+ case ALCHEMY_USB_EHCI0:
+ __au1300_ehci_control(base, enable);
+ break;
+ case ALCHEMY_USB_UDC0:
+ __au1300_udc_control(base, enable);
+ break;
+ case ALCHEMY_USB_OTG0:
+ __au1300_otg_control(base, enable);
+ break;
+ default:
+ ret = -ENODEV;
+ }
+ return ret;
+}
+
+static inline void au1300_usb_init(void)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+
+ /* set some sane defaults. Note: we don't fiddle with DWC_CTRL4
+ * here at all: Port 2 routing (EHCI or UDC) must be set either
+ * by boot firmware or platform init code; I can't autodetect
+ * a sane setting.
+ */
+ __raw_writel(0, base + USB_INT_ENABLE); /* disable all USB irqs */
+ wmb();
+ __raw_writel(0, base + USB_DWC_CTRL3); /* disable all clocks */
+ wmb();
+ __raw_writel(~0, base + USB_MSR_ERR); /* clear all errors */
+ wmb();
+ __raw_writel(~0, base + USB_INT_STATUS); /* clear int status */
+ wmb();
+ /* set coherent access bit */
+ __raw_writel(USB_SBUS_CTRL_SBCA, base + USB_SBUS_CTRL);
+ wmb();
+}
static inline void __au1200_ohci_control(void __iomem *base, int enable)
{
@@ -233,6 +487,9 @@ int alchemy_usb_control(int block, int enable)
case ALCHEMY_CPU_AU1200:
ret = au1200_usb_control(block, enable);
break;
+ case ALCHEMY_CPU_AU1300:
+ ret = au1300_usb_control(block, enable);
+ break;
default:
ret = -ENODEV;
}
@@ -281,6 +538,20 @@ static void au1200_usb_pm(int susp)
}
}
+static void au1300_usb_pm(int susp)
+{
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+ /* remember Port2 routing */
+ if (susp) {
+ alchemy_usb_pmdata[0] = __raw_readl(base + USB_DWC_CTRL4);
+ } else {
+ au1300_usb_init();
+ __raw_writel(alchemy_usb_pmdata[0], base + USB_DWC_CTRL4);
+ wmb();
+ }
+}
+
static void alchemy_usb_pm(int susp)
{
switch (alchemy_get_cputype()) {
@@ -295,6 +566,9 @@ static void alchemy_usb_pm(int susp)
case ALCHEMY_CPU_AU1200:
au1200_usb_pm(susp);
break;
+ case ALCHEMY_CPU_AU1300:
+ au1300_usb_pm(susp);
+ break;
}
}
@@ -328,6 +602,9 @@ static int __init alchemy_usb_init(void)
case ALCHEMY_CPU_AU1200:
au1200_usb_init();
break;
+ case ALCHEMY_CPU_AU1300:
+ au1300_usb_init();
+ break;
}
register_syscore_ops(&alchemy_usb_pm_ops);
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index 9b66df8..95d1a71 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -89,7 +89,7 @@ static const struct hc_driver ohci_au1xxx_hc_driver = {
static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
{
- int ret;
+ int ret, unit;
struct usb_hcd *hcd;
if (usb_disabled())
@@ -120,7 +120,9 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
goto err2;
}
- if (alchemy_usb_control(ALCHEMY_USB_OHCI0, 1)) {
+ unit = (hcd->rsrc_start == AU1300_USB_OHCI1_PHYS_ADDR) ?
+ ALCHEMY_USB_OHCI1 : ALCHEMY_USB_OHCI0;
+ if (alchemy_usb_control(unit, 1)) {
printk(KERN_INFO "%s: controller init failed!\n", pdev->name);
ret = -ENODEV;
goto err3;
@@ -135,7 +137,7 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
return ret;
}
- alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
+ alchemy_usb_control(unit, 0);
err3:
iounmap(hcd->regs);
err2:
@@ -148,9 +150,12 @@ err1:
static int ohci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ int unit;
+ unit = (hcd->rsrc_start == AU1300_USB_OHCI1_PHYS_ADDR) ?
+ ALCHEMY_USB_OHCI1 : ALCHEMY_USB_OHCI0;
usb_remove_hcd(hcd);
- alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
+ alchemy_usb_control(unit, 0);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index d83e967..acd4ba5 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1763,16 +1763,16 @@ config FB_AU1100
au1100fb:panel=<name>.
config FB_AU1200
- bool "Au1200 LCD Driver"
+ bool "Au1200/Au1300 LCD Driver"
depends on (FB = y) && MIPS_ALCHEMY
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
help
- This is the framebuffer driver for the AMD Au1200 SOC. It can drive
- various panels and CRTs by passing in kernel cmd line option
- au1200fb:panel=<name>.
+ This is the framebuffer driver for the Au1200/Au1300 SOCs.
+ It can drive various panels and CRTs by passing in kernel cmd line
+ option au1200fb:panel=<name>.
config FB_VT8500
bool "VT8500 LCD Driver"
diff --git a/sound/soc/au1x/Kconfig b/sound/soc/au1x/Kconfig
index e908a81..93323cc 100644
--- a/sound/soc/au1x/Kconfig
+++ b/sound/soc/au1x/Kconfig
@@ -1,13 +1,13 @@
##
-## Au1200/Au1550 PSC + DBDMA
+## Au1200/Au1550/Au1300 PSC + DBDMA
##
config SND_SOC_AU1XPSC
- tristate "SoC Audio for Au1200/Au1250/Au1550"
+ tristate "SoC Audio for Au12xx/Au13xx/Au1550"
depends on MIPS_ALCHEMY
help
This option enables support for the Programmable Serial
Controllers in AC97 and I2S mode, and the Descriptor-Based DMA
- Controller (DBDMA) as found on the Au1200/Au1250/Au1550 SoC.
+ Controller (DBDMA) as found on the Au12xx/Au13xx/Au1550 SoC.
config SND_SOC_AU1XPSC_I2S
tristate
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 05/18] MIPS: Alchemy: DB1300 support
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (3 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 04/18] MIPS: Alchemy: Au1300 SoC support Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 06/18] MIPS: Alchemy: better DB1550 support Manuel Lauss
` (12 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Basic support for the DB1300 board.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Kconfig | 8 +
arch/mips/alchemy/Platform | 7 +
arch/mips/alchemy/devboards/Makefile | 1 +
arch/mips/alchemy/devboards/db1300.c | 786 ++++++++++++++++++++++++++++
arch/mips/alchemy/devboards/prom.c | 4 +
arch/mips/boot/compressed/uart-alchemy.c | 5 +-
arch/mips/configs/db1300_defconfig | 391 ++++++++++++++
arch/mips/include/asm/mach-db1x00/bcsr.h | 34 +-
arch/mips/include/asm/mach-db1x00/db1300.h | 40 ++
arch/mips/include/asm/mach-db1x00/irq.h | 23 +
drivers/pcmcia/Kconfig | 4 +-
drivers/pcmcia/db1xxx_ss.c | 26 +-
drivers/video/au1200fb.c | 36 ++
sound/soc/au1x/Kconfig | 10 +-
sound/soc/au1x/db1200.c | 43 ++-
15 files changed, 1398 insertions(+), 20 deletions(-)
create mode 100644 arch/mips/alchemy/devboards/db1300.c
create mode 100644 arch/mips/configs/db1300_defconfig
create mode 100644 arch/mips/include/asm/mach-db1x00/db1300.h
create mode 100644 arch/mips/include/asm/mach-db1x00/irq.h
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 766bada..f9a13be 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -49,6 +49,14 @@ config MIPS_DB1200
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
+config MIPS_DB1300
+ bool "NetLogic DB1300 board"
+ select ALCHEMY_GPIOINT_AU1300
+ select DMA_COHERENT
+ select MIPS_DISABLE_OBSOLETE_IDE
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
+
config MIPS_DB1500
bool "Alchemy DB1500 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 2920af9..4d13e21 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -68,6 +68,13 @@ cflags-$(CONFIG_MIPS_DB1200) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1200) += 0xffffffff80100000
#
+# NetLogic DBAu1300 development platform
+#
+platform-$(CONFIG_MIPS_DB1300) += alchemy/devboards/
+cflags-$(CONFIG_MIPS_DB1300) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
+load-$(CONFIG_MIPS_DB1300) += 0xffffffff80100000
+
+#
# 4G-Systems eval board
#
platform-$(CONFIG_MIPS_MTX1) += alchemy/mtx-1/
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 5afaf94..2eb75c9 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -11,5 +11,6 @@ obj-$(CONFIG_MIPS_PB1550) += pb1550/
obj-$(CONFIG_MIPS_DB1000) += db1x00/
obj-$(CONFIG_MIPS_DB1100) += db1x00/
obj-$(CONFIG_MIPS_DB1200) += db1200/
+obj-$(CONFIG_MIPS_DB1300) += db1300.o
obj-$(CONFIG_MIPS_DB1500) += db1x00/
obj-$(CONFIG_MIPS_DB1550) += db1x00/
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
new file mode 100644
index 0000000..bf0d1c4
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -0,0 +1,786 @@
+/*
+ * DBAu1300 init and platform device setup.
+ *
+ * (c) 2009 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/init.h>
+#include <linux/input.h> /* KEY_* codes */
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/ata_platform.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/smsc911x.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-db1x00/db1300.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-au1x00/prom.h>
+
+#include "platform.h"
+
+static struct i2c_board_info db1300_i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("wm8731", 0x1b), }, /* I2S audio codec */
+ { I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
+};
+
+/* multifunction pins to assign to GPIO controller */
+static int db1300_gpio_pins[] __initdata = {
+ AU1300_PIN_LCDPWM0, AU1300_PIN_PSC2SYNC1, AU1300_PIN_WAKE1,
+ AU1300_PIN_WAKE2, AU1300_PIN_WAKE3, AU1300_PIN_FG3AUX,
+ AU1300_PIN_EXTCLK1,
+ -1, /* terminator */
+};
+
+/* multifunction pins to assign to device functions */
+static int db1300_dev_pins[] __initdata = {
+ /* wake-from-str pins 0-3 */
+ AU1300_PIN_WAKE0,
+ /* external clock sources for PSC0 */
+ AU1300_PIN_EXTCLK0,
+ /* 8bit MMC interface on SD0: 6-9 */
+ AU1300_PIN_SD0DAT4, AU1300_PIN_SD0DAT5, AU1300_PIN_SD0DAT6,
+ AU1300_PIN_SD0DAT7,
+ /* UART1 pins: 11-18 */
+ AU1300_PIN_U1RI, AU1300_PIN_U1DCD, AU1300_PIN_U1DSR,
+ AU1300_PIN_U1CTS, AU1300_PIN_U1RTS, AU1300_PIN_U1DTR,
+ AU1300_PIN_U1RX, AU1300_PIN_U1TX,
+ /* UART0 pins: 19-24 */
+ AU1300_PIN_U0RI, AU1300_PIN_U0DCD, AU1300_PIN_U0DSR,
+ AU1300_PIN_U0CTS, AU1300_PIN_U0RTS, AU1300_PIN_U0DTR,
+ /* UART2: 25-26 */
+ AU1300_PIN_U2RX, AU1300_PIN_U2TX,
+ /* UART3: 27-28 */
+ AU1300_PIN_U3RX, AU1300_PIN_U3TX,
+ /* LCD controller PWMs, ext pixclock: 30-31 */
+ AU1300_PIN_LCDPWM1, AU1300_PIN_LCDCLKIN,
+ /* SD1 interface: 32-37 */
+ AU1300_PIN_SD1DAT0, AU1300_PIN_SD1DAT1, AU1300_PIN_SD1DAT2,
+ AU1300_PIN_SD1DAT3, AU1300_PIN_SD1CMD, AU1300_PIN_SD1CLK,
+ /* SD2 interface: 38-43 */
+ AU1300_PIN_SD2DAT0, AU1300_PIN_SD2DAT1, AU1300_PIN_SD2DAT2,
+ AU1300_PIN_SD2DAT3, AU1300_PIN_SD2CMD, AU1300_PIN_SD2CLK,
+ /* PSC0/1 clocks: 44-45 */
+ AU1300_PIN_PSC0CLK, AU1300_PIN_PSC1CLK,
+ /* PSCs: 46-49/50-53/54-57/58-61 */
+ AU1300_PIN_PSC0SYNC0, AU1300_PIN_PSC0SYNC1, AU1300_PIN_PSC0D0,
+ AU1300_PIN_PSC0D1,
+ AU1300_PIN_PSC1SYNC0, AU1300_PIN_PSC1SYNC1, AU1300_PIN_PSC1D0,
+ AU1300_PIN_PSC1D1,
+ AU1300_PIN_PSC2SYNC0, AU1300_PIN_PSC2D0,
+ AU1300_PIN_PSC2D1,
+ AU1300_PIN_PSC3SYNC0, AU1300_PIN_PSC3SYNC1, AU1300_PIN_PSC3D0,
+ AU1300_PIN_PSC3D1,
+ /* PCMCIA interface: 62-70 */
+ AU1300_PIN_PCE2, AU1300_PIN_PCE1, AU1300_PIN_PIOS16,
+ AU1300_PIN_PIOR, AU1300_PIN_PWE, AU1300_PIN_PWAIT,
+ AU1300_PIN_PREG, AU1300_PIN_POE, AU1300_PIN_PIOW,
+ /* camera interface H/V sync inputs: 71-72 */
+ AU1300_PIN_CIMLS, AU1300_PIN_CIMFS,
+ /* PSC2/3 clocks: 73-74 */
+ AU1300_PIN_PSC2CLK, AU1300_PIN_PSC3CLK,
+ -1, /* terminator */
+};
+
+static void __init db1300_gpio_config(void)
+{
+ int *i;
+
+ i = &db1300_dev_pins[0];
+ while (*i != -1)
+ au1300_pinfunc_to_dev(*i++);
+
+ i = &db1300_gpio_pins[0];
+ while (*i != -1)
+ au1300_gpio_direction_input(*i++);/* implies pin_to_gpio */
+
+ au1300_set_dbdma_gpio(1, AU1300_PIN_FG3AUX);
+}
+
+char *get_system_type(void)
+{
+ return "DB1300";
+}
+
+/**********************************************************************/
+
+static void au1300_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1300_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1300_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1300_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1300_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1300_nand_parts),
+ .partitions = db1300_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1300_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1300_nand_device_ready,
+ .cmd_ctrl = au1300_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1300_nand_res[] = {
+ [0] = {
+ .start = DB1300_NAND_PHYS_ADDR,
+ .end = DB1300_NAND_PHYS_ADDR + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1300_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1300_nand_res),
+ .resource = db1300_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1300_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct resource db1300_eth_res[] = {
+ [0] = {
+ .start = DB1300_ETH_PHYS_ADDR,
+ .end = DB1300_ETH_PHYS_END,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1300_ETH_INT,
+ .end = DB1300_ETH_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct smsc911x_platform_config db1300_eth_config = {
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
+ .flags = SMSC911X_USE_32BIT,
+};
+
+static struct platform_device db1300_eth_dev = {
+ .name = "smsc911x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(db1300_eth_res),
+ .resource = db1300_eth_res,
+ .dev = {
+ .platform_data = &db1300_eth_config,
+ },
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc1_res[] = {
+ [0] = {
+ .start = AU1300_PSC1_PHYS_ADDR,
+ .end = AU1300_PSC1_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_PSC1_INT,
+ .end = AU1300_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_PSC1_TX,
+ .end = AU1300_DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_PSC1_RX,
+ .end = AU1300_DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_ac97_dev = {
+ .name = "au1xpsc_ac97",
+ .id = 1, /* PSC ID. match with AC97 codec ID! */
+ .num_resources = ARRAY_SIZE(au1300_psc1_res),
+ .resource = au1300_psc1_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc2_res[] = {
+ [0] = {
+ .start = AU1300_PSC2_PHYS_ADDR,
+ .end = AU1300_PSC2_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_PSC2_INT,
+ .end = AU1300_PSC2_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_PSC2_TX,
+ .end = AU1300_DSCR_CMD0_PSC2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_PSC2_RX,
+ .end = AU1300_DSCR_CMD0_PSC2_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_i2s_dev = {
+ .name = "au1xpsc_i2s",
+ .id = 2, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1300_psc2_res),
+ .resource = au1300_psc2_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc3_res[] = {
+ [0] = {
+ .start = AU1300_PSC3_PHYS_ADDR,
+ .end = AU1300_PSC3_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_PSC3_INT,
+ .end = AU1300_PSC3_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_PSC3_TX,
+ .end = AU1300_DSCR_CMD0_PSC3_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_PSC3_RX,
+ .end = AU1300_DSCR_CMD0_PSC3_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1300_psc3_res),
+ .resource = au1300_psc3_res,
+};
+
+/**********************************************************************/
+
+/* proper key assignments when facing the LCD panel. For key assignments
+ * according to the schematics swap up with down and left with right.
+ * I chose to use it to emulate the arrow keys of a keyboard.
+ */
+static struct gpio_keys_button db1300_5waysw_arrowkeys[] = {
+ {
+ .code = KEY_DOWN,
+ .gpio = AU1300_PIN_LCDPWM0,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-down",
+ },
+ {
+ .code = KEY_UP,
+ .gpio = AU1300_PIN_PSC2SYNC1,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-up",
+ },
+ {
+ .code = KEY_RIGHT,
+ .gpio = AU1300_PIN_WAKE3,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-right",
+ },
+ {
+ .code = KEY_LEFT,
+ .gpio = AU1300_PIN_WAKE2,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-left",
+ },
+ {
+ .code = KEY_ENTER,
+ .gpio = AU1300_PIN_WAKE1,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-push",
+ },
+};
+
+static struct gpio_keys_platform_data db1300_5waysw_data = {
+ .buttons = db1300_5waysw_arrowkeys,
+ .nbuttons = ARRAY_SIZE(db1300_5waysw_arrowkeys),
+ .rep = 1,
+ .name = "db1300-5wayswitch",
+};
+
+static struct platform_device db1300_5waysw_dev = {
+ .name = "gpio-keys",
+ .dev = {
+ .platform_data = &db1300_5waysw_data,
+ },
+};
+
+/**********************************************************************/
+
+static struct platform_device db1300_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+static struct pata_platform_info db1300_ide_info = {
+ .ioport_shift = DB1300_IDE_REG_SHIFT,
+};
+
+#define IDE_ALT_START (14 << DB1300_IDE_REG_SHIFT)
+static struct resource db1300_ide_res[] = {
+ [0] = {
+ .start = DB1300_IDE_PHYS_ADDR,
+ .end = DB1300_IDE_PHYS_ADDR + IDE_ALT_START - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1300_IDE_PHYS_ADDR + IDE_ALT_START,
+ .end = DB1300_IDE_PHYS_ADDR + DB1300_IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = DB1300_IDE_INT,
+ .end = DB1300_IDE_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1300_ide_dev = {
+ .dev = {
+ .platform_data = &db1300_ide_info,
+ },
+ .name = "pata_platform",
+ .resource = db1300_ide_res,
+ .num_resources = ARRAY_SIZE(db1300_ide_res),
+};
+
+/**********************************************************************/
+
+static irqreturn_t db1300_mmc_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ /* disable the one currently screaming. No other way to shut it up */
+ if (irq == DB1300_SD1_INSERT_INT) {
+ disable_irq_nosync(DB1300_SD1_INSERT_INT);
+ enable_irq(DB1300_SD1_EJECT_INT);
+ } else {
+ disable_irq_nosync(DB1300_SD1_EJECT_INT);
+ enable_irq(DB1300_SD1_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m. We can only be called once MMC core has
+ * initialized the controller, so symbol_get() should always succeed.
+ */
+ mmc_cd = symbol_get(mmc_detect_change);
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+
+ return IRQ_HANDLED;
+}
+
+static int db1300_mmc_card_readonly(void *mmc_host)
+{
+ /* it uses SD1 interface, but the DB1200's SD0 bit in the CPLD */
+ return bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP;
+}
+
+static int db1300_mmc_card_inserted(void *mmc_host)
+{
+ return bcsr_read(BCSR_SIGSTAT) & (1 << 12); /* insertion irq signal */
+}
+
+static int db1300_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(DB1300_SD1_INSERT_INT, db1300_mmc_cd, 0,
+ "sd_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(DB1300_SD1_EJECT_INT, db1300_mmc_cd, 0,
+ "sd_eject", mmc_host);
+ if (ret) {
+ free_irq(DB1300_SD1_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (db1300_mmc_card_inserted(mmc_host))
+ enable_irq(DB1300_SD1_EJECT_INT);
+ else
+ enable_irq(DB1300_SD1_INSERT_INT);
+
+ } else {
+ free_irq(DB1300_SD1_INSERT_INT, mmc_host);
+ free_irq(DB1300_SD1_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void db1300_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1300_mmc_led = {
+ .brightness_set = db1300_mmcled_set,
+};
+
+struct au1xmmc_platform_data db1300_sd1_platdata = {
+ .cd_setup = db1300_mmc_cd_setup,
+ .card_inserted = db1300_mmc_card_inserted,
+ .card_readonly = db1300_mmc_card_readonly,
+ .led = &db1300_mmc_led,
+};
+
+static struct resource au1300_sd1_res[] = {
+ [0] = {
+ .start = AU1300_SD1_PHYS_ADDR,
+ .end = AU1300_SD1_PHYS_ADDR,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_SD1_INT,
+ .end = AU1300_SD1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_SDMS_TX1,
+ .end = AU1300_DSCR_CMD0_SDMS_TX1,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_SDMS_RX1,
+ .end = AU1300_DSCR_CMD0_SDMS_RX1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_sd1_dev = {
+ .dev = {
+ .platform_data = &db1300_sd1_platdata,
+ },
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .resource = au1300_sd1_res,
+ .num_resources = ARRAY_SIZE(au1300_sd1_res),
+};
+
+/**********************************************************************/
+
+static int db1300_movinand_inserted(void *mmc_host)
+{
+ return 0; /* disable for now, it doesn't work yet */
+}
+
+static int db1300_movinand_readonly(void *mmc_host)
+{
+ return 0;
+}
+
+static void db1300_movinand_led_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev db1300_movinand_led = {
+ .brightness_set = db1300_movinand_led_set,
+};
+
+struct au1xmmc_platform_data db1300_sd0_platdata = {
+ .card_inserted = db1300_movinand_inserted,
+ .card_readonly = db1300_movinand_readonly,
+ .led = &db1300_movinand_led,
+ .mask_host_caps = MMC_CAP_NEEDS_POLL,
+};
+
+static struct resource au1300_sd0_res[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_SD0_INT,
+ .end = AU1300_SD0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_SDMS_TX0,
+ .end = AU1300_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_SDMS_RX0,
+ .end = AU1300_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_sd0_dev = {
+ .dev = {
+ .platform_data = &db1300_sd0_platdata,
+ },
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .resource = au1300_sd0_res,
+ .num_resources = ARRAY_SIZE(au1300_sd0_res),
+};
+
+/**********************************************************************/
+
+static struct platform_device db1300_wm9715_dev = {
+ .name = "wm9712-codec",
+ .id = 1, /* ID of PSC for AC97 audio, see asoc glue! */
+};
+
+static struct platform_device db1300_ac97dma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device db1300_i2sdma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 2, /* PSC ID */
+};
+
+static struct platform_device db1300_sndac97_dev = {
+ .name = "db1300-ac97",
+};
+
+static struct platform_device db1300_sndi2s_dev = {
+ .name = "db1300-i2s",
+};
+
+/**********************************************************************/
+
+static struct resource au1300_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_LCD_INT,
+ .end = AU1300_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1300_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1300_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1300_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1300_lcd_res),
+ .resource = au1300_lcd_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device *db1300_dev[] __initdata = {
+ &db1300_eth_dev,
+ &db1300_i2c_dev,
+ &db1300_5waysw_dev,
+ &db1300_rtc_dev,
+ &db1300_nand_dev,
+ &db1300_ide_dev,
+ &db1300_sd0_dev,
+ &db1300_sd1_dev,
+ &db1300_lcd_dev,
+ &db1300_ac97_dev,
+ &db1300_i2s_dev,
+ &db1300_wm9715_dev,
+ &db1300_ac97dma_dev,
+ &db1300_i2sdma_dev,
+ &db1300_sndac97_dev,
+ &db1300_sndi2s_dev,
+};
+
+static int __init db1300_device_init(void)
+{
+ int swapped, cpldirq;
+
+ /* setup CPLD IRQ muxer */
+ cpldirq = au1300_gpio_to_irq(AU1300_PIN_EXTCLK1);
+ irq_set_irq_type(cpldirq, IRQ_TYPE_LEVEL_HIGH);
+ bcsr_init_irq(DB1300_FIRST_INT, DB1300_LAST_INT, cpldirq);
+
+ /* insert/eject IRQs: one always triggers so don't enable them
+ * when doing request_irq() on them. DB1200 has this bug too.
+ */
+ irq_set_status_flags(DB1300_SD1_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1300_SD1_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1300_CF_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1300_CF_EJECT_INT, IRQ_NOAUTOEN);
+
+ /*
+ * setup board
+ */
+ prom_get_ethernet_addr(&db1300_eth_config.mac[0]);
+
+ i2c_register_board_info(0, db1300_i2c_devs,
+ ARRAY_SIZE(db1300_i2c_devs));
+
+ /* Audio PSC clock is supplied by codecs (PSC1, 2) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1300_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1300_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ /* I2C uses internal 48MHz EXTCLK1 */
+ __raw_writel(PSC_SEL_CLK_INTCLK,
+ (void __iomem *)KSEG1ADDR(AU1300_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ /* enable power to USB ports */
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_USBHPWR | BCSR_RESETS_OTGPWR);
+
+ /* although it is socket #0, it uses the CPLD bits which previous boards
+ * have used for socket #1.
+ */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x00400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x00400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x00010000 - 1,
+ DB1300_CF_INT, DB1300_CF_INSERT_INT, 0, DB1300_CF_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(64 << 20, 2, swapped);
+
+ return platform_add_devices(db1300_dev, ARRAY_SIZE(db1300_dev));
+}
+device_initcall(db1300_device_init);
+
+
+void __init board_setup(void)
+{
+ unsigned short whoami;
+
+ db1300_gpio_config();
+ bcsr_init(DB1300_BCSR_PHYS_ADDR,
+ DB1300_BCSR_PHYS_ADDR + DB1300_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "NetLogic DBAu1300 Development Platform.\n\t"
+ "BoardID %d CPLD Rev %d DaughtercardID %d\n",
+ BCSR_WHOAMI_BOARD(whoami), BCSR_WHOAMI_CPLD(whoami),
+ BCSR_WHOAMI_DCID(whoami));
+
+ /* enable UARTs, YAMON only enables #2 */
+ alchemy_uart_enable(AU1300_UART0_PHYS_ADDR);
+ alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
+ alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
+}
+
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+ return 9; /* DB1300_800x480 */
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
+ BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index f734833..3a73f96 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -61,5 +61,9 @@ void __init prom_init(void)
void prom_putchar(unsigned char c)
{
+#ifdef CONFIG_MIPS_DB1300
+ alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
+#else
alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+#endif
}
diff --git a/arch/mips/boot/compressed/uart-alchemy.c b/arch/mips/boot/compressed/uart-alchemy.c
index eb063e6..3112df8 100644
--- a/arch/mips/boot/compressed/uart-alchemy.c
+++ b/arch/mips/boot/compressed/uart-alchemy.c
@@ -2,6 +2,9 @@
void putc(char c)
{
- /* all current (Jan. 2010) in-kernel boards */
+#ifdef CONFIG_MIPS_DB1300
+ alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
+#else
alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+#endif
}
diff --git a/arch/mips/configs/db1300_defconfig b/arch/mips/configs/db1300_defconfig
new file mode 100644
index 0000000..c38b190
--- /dev/null
+++ b/arch/mips/configs/db1300_defconfig
@@ -0,0 +1,391 @@
+CONFIG_MIPS=y
+CONFIG_MIPS_ALCHEMY=y
+CONFIG_ALCHEMY_GPIOINT_AU1300=y
+CONFIG_MIPS_DB1300=y
+CONFIG_SOC_AU1300=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_DMA_COHERENT=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_MIPS_DISABLE_OBSOLETE_IDE=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+CONFIG_IRQ_CPU=y
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_SYS_SUPPORTS_ZBOOT=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_32BIT=y
+CONFIG_PAGE_SIZE_4KB=y
+CONFIG_FORCE_MAX_ZONEORDER=11
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_MIPS_MT_DISABLED=y
+CONFIG_64BIT_PHYS_ADDR=y
+CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_COMPACTION=y
+CONFIG_MIGRATION=y
+CONFIG_PHYS_ADDR_T_64BIT=y
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_HZ_100=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_HZ=100
+CONFIG_PREEMPT_NONE=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+CONFIG_HAVE_IRQ_WORK=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
+CONFIG_LOCALVERSION="-db1300"
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_LZMA=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+CONFIG_FHANDLE=y
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_TINY_RCU=y
+CONFIG_LOG_BUF_SHIFT=19
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+CONFIG_USER_NS=y
+CONFIG_PID_NS=y
+CONFIG_NET_NS=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EXPERT=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_EMBEDDED=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_SLAB=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+CONFIG_BLK_DEV_BSG=y
+CONFIG_IOSCHED_NOOP=y
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_INLINE_SPIN_UNLOCK=y
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+CONFIG_INLINE_READ_UNLOCK=y
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+CONFIG_INLINE_WRITE_UNLOCK=y
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+CONFIG_MMU=y
+CONFIG_PCCARD=y
+CONFIG_PCMCIA=y
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
+CONFIG_BINFMT_ELF=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_TRAD_SIGNALS=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_INET_TUNNEL=y
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+CONFIG_IPV6=y
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_BLK_DEV=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_UB=y
+CONFIG_HAVE_IDE=y
+CONFIG_IDE=y
+CONFIG_IDE_GD=y
+CONFIG_IDE_GD_ATA=y
+CONFIG_BLK_DEV_IDECS=y
+CONFIG_IDE_TASK_IOCTL=y
+CONFIG_IDE_PROC_FS=y
+CONFIG_BLK_DEV_PLATFORM=y
+CONFIG_SCSI_MOD=y
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_PHYLIB=y
+CONFIG_SMSC_PHY=y
+CONFIG_NET_ETHERNET=y
+CONFIG_SMSC911X=y
+CONFIG_INPUT=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_WM97XX=y
+CONFIG_TOUCHSCREEN_WM9712=y
+CONFIG_TOUCHSCREEN_WM9713=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_SMBUS=y
+CONFIG_I2C_AU1550=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_AU1550=y
+CONFIG_SPI_BITBANG=y
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_HWMON=y
+CONFIG_HWMON_VID=y
+CONFIG_SENSORS_ADM1025=y
+CONFIG_FB=y
+CONFIG_FB_AU1200=y
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FONTS=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+CONFIG_SND_HRTIMER=y
+CONFIG_SND_DYNAMIC_MINORS=y
+CONFIG_SND_VERBOSE_PROCFS=y
+CONFIG_SND_VERBOSE_PRINTK=y
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_CACHE_LZO=y
+CONFIG_SND_SOC_AC97_BUS=y
+CONFIG_SND_SOC_AU1XPSC=y
+CONFIG_SND_SOC_AU1XPSC_I2S=y
+CONFIG_SND_SOC_AU1XPSC_AC97=y
+CONFIG_SND_SOC_DB1300=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+CONFIG_SND_SOC_WM8731=y
+CONFIG_SND_SOC_WM9712=y
+CONFIG_AC97_BUS=y
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+CONFIG_HIDRAW=y
+CONFIG_USB_HID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+CONFIG_USB_DYNAMIC_MINORS=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_EHCI_TT_NEWSCHED=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_AU1XXX=y
+CONFIG_EXT2_FS=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_EXPORTFS=y
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_GENERIC_ACL=y
+CONFIG_FAT_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_FS_POSIX_ACL=y
+CONFIG_JFFS2_FS_SECURITY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_JFFS2_CMODE_PRIORITY=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_UTF8=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="video=au1200fb:panel:bs console=tty console=ttyS2,115200"
+CONFIG_DEBUG_ZBOOT=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+CONFIG_BITREVERSE=y
+CONFIG_CRC32=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_XZ_DEC=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
diff --git a/arch/mips/include/asm/mach-db1x00/bcsr.h b/arch/mips/include/asm/mach-db1x00/bcsr.h
index 618d2de..0ef6300 100644
--- a/arch/mips/include/asm/mach-db1x00/bcsr.h
+++ b/arch/mips/include/asm/mach-db1x00/bcsr.h
@@ -34,6 +34,8 @@
#define PB1200_BCSR_PHYS_ADDR 0x0D800000
#define PB1200_BCSR_HEXLED_OFS 0x00400000
+#define DB1300_BCSR_PHYS_ADDR 0x19800000
+#define DB1300_BCSR_HEXLED_OFS 0x00400000
enum bcsr_id {
/* BCSR base 1 */
@@ -105,6 +107,7 @@ enum bcsr_whoami_boards {
BCSR_WHOAMI_PB1200 = BCSR_WHOAMI_PB1200_DDR1,
BCSR_WHOAMI_PB1200_DDR2,
BCSR_WHOAMI_DB1200,
+ BCSR_WHOAMI_DB1300,
};
/* STATUS reg. Unless otherwise noted, they're valid on all boards.
@@ -118,12 +121,12 @@ enum bcsr_whoami_boards {
#define BCSR_STATUS_SRAMWIDTH 0x0080
#define BCSR_STATUS_FLASHBUSY 0x0100
#define BCSR_STATUS_ROMBUSY 0x0400
-#define BCSR_STATUS_SD0WP 0x0400 /* DB1200 */
+#define BCSR_STATUS_SD0WP 0x0400 /* DB1200/DB1300:SD1 */
#define BCSR_STATUS_SD1WP 0x0800
#define BCSR_STATUS_USBOTGID 0x0800 /* PB/DB1550 */
#define BCSR_STATUS_DB1000_SWAPBOOT 0x2000
-#define BCSR_STATUS_DB1200_SWAPBOOT 0x0040 /* DB1200 */
-#define BCSR_STATUS_IDECBLID 0x0200 /* DB1200 */
+#define BCSR_STATUS_DB1200_SWAPBOOT 0x0040 /* DB1200/1300 */
+#define BCSR_STATUS_IDECBLID 0x0200 /* DB1200/1300 */
#define BCSR_STATUS_DB1200_U0RXD 0x1000 /* DB1200 */
#define BCSR_STATUS_DB1200_U1RXD 0x2000 /* DB1200 */
#define BCSR_STATUS_FLASHDEN 0xC000
@@ -133,6 +136,11 @@ enum bcsr_whoami_boards {
#define BCSR_STATUS_PB1550_U1RXD 0x2000 /* PB1550 */
#define BCSR_STATUS_PB1550_U3RXD 0x8000 /* PB1550 */
+#define BCSR_STATUS_CFWP 0x4000 /* DB1300 */
+#define BCSR_STATUS_USBOCn 0x2000 /* DB1300 */
+#define BCSR_STATUS_OTGOCn 0x1000 /* DB1300 */
+#define BCSR_STATUS_DCDMARQ 0x0010 /* DB1300 */
+#define BCSR_STATUS_IDEDMARQ 0x0020 /* DB1300 */
/* DB/PB1000,1100,1500,1550 */
#define BCSR_RESETS_PHY0 0x0001
@@ -160,12 +168,12 @@ enum bcsr_whoami_boards {
#define BCSR_BOARD_SD1WP 0x8000 /* DB1100 */
-/* DB/PB1200 */
+/* DB/PB1200/1300 */
#define BCSR_RESETS_ETH 0x0001
#define BCSR_RESETS_CAMERA 0x0002
#define BCSR_RESETS_DC 0x0004
#define BCSR_RESETS_IDE 0x0008
-#define BCSR_RESETS_TV 0x0010 /* DB1200 */
+#define BCSR_RESETS_TV 0x0010 /* DB1200/1300 */
/* Not resets but in the same register */
#define BCSR_RESETS_PWMR1MUX 0x0800 /* DB1200 */
#define BCSR_RESETS_PB1200_WSCFSM 0x0800 /* PB1200 */
@@ -174,13 +182,22 @@ enum bcsr_whoami_boards {
#define BCSR_RESETS_SPISEL 0x4000
#define BCSR_RESETS_SD1MUX 0x8000 /* PB1200 */
+#define BCSR_RESETS_VDDQSHDN 0x0200 /* DB1300 */
+#define BCSR_RESETS_OTPPGM 0x0400 /* DB1300 */
+#define BCSR_RESETS_OTPSCLK 0x0800 /* DB1300 */
+#define BCSR_RESETS_OTPWRPROT 0x1000 /* DB1300 */
+#define BCSR_RESETS_OTPCSB 0x2000 /* DB1300 */
+#define BCSR_RESETS_OTGPWR 0x4000 /* DB1300 */
+#define BCSR_RESETS_USBHPWR 0x8000 /* DB1300 */
+
#define BCSR_BOARD_LCDVEE 0x0001
#define BCSR_BOARD_LCDVDD 0x0002
#define BCSR_BOARD_LCDBL 0x0004
#define BCSR_BOARD_CAMSNAP 0x0010
#define BCSR_BOARD_CAMPWR 0x0020
#define BCSR_BOARD_SD0PWR 0x0040
-
+#define BCSR_BOARD_CAMCS 0x0010 /* DB1300 */
+#define BCSR_BOARD_HDMI_DE 0x0040 /* DB1300 */
#define BCSR_SWITCHES_DIP 0x00FF
#define BCSR_SWITCHES_DIP_1 0x0080
@@ -214,7 +231,10 @@ enum bcsr_whoami_boards {
#define BCSR_SYSTEM_RESET 0x8000 /* clear to reset */
#define BCSR_SYSTEM_PWROFF 0x4000 /* set to power off */
#define BCSR_SYSTEM_VDDI 0x001F /* PB1xxx boards */
-
+#define BCSR_SYSTEM_DEBUGCSMASK 0x003F /* DB1300 */
+#define BCSR_SYSTEM_UDMAMODE 0x0100 /* DB1300 */
+#define BCSR_SYSTEM_WAKEONIRQ 0x0200 /* DB1300 */
+#define BCSR_SYSTEM_VDDI1300 0x3C00 /* DB1300 */
diff --git a/arch/mips/include/asm/mach-db1x00/db1300.h b/arch/mips/include/asm/mach-db1x00/db1300.h
new file mode 100644
index 0000000..7fe5fb3
--- /dev/null
+++ b/arch/mips/include/asm/mach-db1x00/db1300.h
@@ -0,0 +1,40 @@
+/*
+ * NetLogic DB1300 board constants
+ */
+
+#ifndef _DB1300_H_
+#define _DB1300_H_
+
+/* FPGA (external mux) interrupt sources */
+#define DB1300_FIRST_INT (ALCHEMY_GPIC_INT_LAST + 1)
+#define DB1300_IDE_INT (DB1300_FIRST_INT + 0)
+#define DB1300_ETH_INT (DB1300_FIRST_INT + 1)
+#define DB1300_CF_INT (DB1300_FIRST_INT + 2)
+#define DB1300_VIDEO_INT (DB1300_FIRST_INT + 4)
+#define DB1300_HDMI_INT (DB1300_FIRST_INT + 5)
+#define DB1300_DC_INT (DB1300_FIRST_INT + 6)
+#define DB1300_FLASH_INT (DB1300_FIRST_INT + 7)
+#define DB1300_CF_INSERT_INT (DB1300_FIRST_INT + 8)
+#define DB1300_CF_EJECT_INT (DB1300_FIRST_INT + 9)
+#define DB1300_AC97_INT (DB1300_FIRST_INT + 10)
+#define DB1300_AC97_PEN_INT (DB1300_FIRST_INT + 11)
+#define DB1300_SD1_INSERT_INT (DB1300_FIRST_INT + 12)
+#define DB1300_SD1_EJECT_INT (DB1300_FIRST_INT + 13)
+#define DB1300_OTG_VBUS_OC_INT (DB1300_FIRST_INT + 14)
+#define DB1300_HOST_VBUS_OC_INT (DB1300_FIRST_INT + 15)
+#define DB1300_LAST_INT (DB1300_FIRST_INT + 15)
+
+/* SMSC9210 CS */
+#define DB1300_ETH_PHYS_ADDR 0x19000000
+#define DB1300_ETH_PHYS_END 0x197fffff
+
+/* ATA CS */
+#define DB1300_IDE_PHYS_ADDR 0x18800000
+#define DB1300_IDE_REG_SHIFT 5
+#define DB1300_IDE_PHYS_LEN (16 << DB1300_IDE_REG_SHIFT)
+
+/* NAND CS */
+#define DB1300_NAND_PHYS_ADDR 0x20000000
+#define DB1300_NAND_PHYS_END 0x20000fff
+
+#endif /* _DB1300_H_ */
diff --git a/arch/mips/include/asm/mach-db1x00/irq.h b/arch/mips/include/asm/mach-db1x00/irq.h
new file mode 100644
index 0000000..15b2669
--- /dev/null
+++ b/arch/mips/include/asm/mach-db1x00/irq.h
@@ -0,0 +1,23 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_IRQ_H
+#define __ASM_MACH_GENERIC_IRQ_H
+
+
+#ifdef NR_IRQS
+#undef NR_IRQS
+#endif
+
+#ifndef MIPS_CPU_IRQ_BASE
+#define MIPS_CPU_IRQ_BASE 0
+#endif
+
+/* 8 (MIPS) + 128 (au1300) + 16 (cpld) */
+#define NR_IRQS 152
+
+#endif /* __ASM_MACH_GENERIC_IRQ_H */
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index c022b5c..f9e3fb3 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -161,8 +161,8 @@ config PCMCIA_ALCHEMY_DEVBOARD
select 64BIT_PHYS_ADDR
help
Enable this driver of you want PCMCIA support on your Alchemy
- Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200 board.
- NOT suitable for the PB1000!
+ Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200, DB1300
+ board. NOT suitable for the PB1000!
This driver is also available as a module called db1xxx_ss.ko
diff --git a/drivers/pcmcia/db1xxx_ss.c b/drivers/pcmcia/db1xxx_ss.c
index 01757f1..984f431 100644
--- a/drivers/pcmcia/db1xxx_ss.c
+++ b/drivers/pcmcia/db1xxx_ss.c
@@ -7,7 +7,7 @@
/* This is a fairly generic PCMCIA socket driver suitable for the
* following Alchemy Development boards:
- * Db1000, Db/Pb1500, Db/Pb1100, Db/Pb1550, Db/Pb1200.
+ * Db1000, Db/Pb1500, Db/Pb1100, Db/Pb1550, Db/Pb1200, Db1300
*
* The Db1000 is used as a reference: Per-socket card-, carddetect- and
* statuschange IRQs connected to SoC GPIOs, control and status register
@@ -18,6 +18,7 @@
* - Pb1100/Pb1500: single socket only; voltage key bits VS are
* at STATUS[5:4] (instead of STATUS[1:0]).
* - Au1200-based: additional card-eject irqs, irqs not gpios!
+ * - Db1300: Db1200-like, no pwr ctrl, single socket (#1).
*/
#include <linux/delay.h>
@@ -58,11 +59,17 @@ struct db1x_pcmcia_sock {
#define BOARD_TYPE_DEFAULT 0 /* most boards */
#define BOARD_TYPE_DB1200 1 /* IRQs aren't gpios */
#define BOARD_TYPE_PB1100 2 /* VS bits slightly different */
+#define BOARD_TYPE_DB1300 3 /* no power control */
int board_type;
};
#define to_db1x_socket(x) container_of(x, struct db1x_pcmcia_sock, socket)
+static int db1300_card_inserted(struct db1x_pcmcia_sock *sock)
+{
+ return bcsr_read(BCSR_SIGSTAT) & (1 << 8);
+}
+
/* DB/PB1200: check CPLD SIGSTATUS register bit 10/12 */
static int db1200_card_inserted(struct db1x_pcmcia_sock *sock)
{
@@ -83,6 +90,8 @@ static int db1x_card_inserted(struct db1x_pcmcia_sock *sock)
switch (sock->board_type) {
case BOARD_TYPE_DB1200:
return db1200_card_inserted(sock);
+ case BOARD_TYPE_DB1300:
+ return db1300_card_inserted(sock);
default:
return db1000_card_inserted(sock);
}
@@ -159,7 +168,8 @@ static int db1x_pcmcia_setup_irqs(struct db1x_pcmcia_sock *sock)
* ejection handler have been registered and the currently
* active one disabled.
*/
- if (sock->board_type == BOARD_TYPE_DB1200) {
+ if ((sock->board_type == BOARD_TYPE_DB1200) ||
+ (sock->board_type == BOARD_TYPE_DB1300)) {
ret = request_irq(sock->insert_irq, db1200_pcmcia_cdirq,
IRQF_DISABLED, "pcmcia_insert", sock);
if (ret)
@@ -173,7 +183,7 @@ static int db1x_pcmcia_setup_irqs(struct db1x_pcmcia_sock *sock)
}
/* enable the currently silent one */
- if (db1200_card_inserted(sock))
+ if (db1x_card_inserted(sock))
enable_irq(sock->eject_irq);
else
enable_irq(sock->insert_irq);
@@ -269,7 +279,8 @@ static int db1x_pcmcia_configure(struct pcmcia_socket *skt,
}
/* create new voltage code */
- cr_set |= ((v << 2) | p) << (sock->nr * 8);
+ if (sock->board_type != BOARD_TYPE_DB1300)
+ cr_set |= ((v << 2) | p) << (sock->nr * 8);
changed = state->flags ^ sock->old_flags;
@@ -342,6 +353,10 @@ static int db1x_pcmcia_get_status(struct pcmcia_socket *skt,
/* if Vcc is not zero, we have applied power to a card */
status |= GET_VCC(cr, sock->nr) ? SS_POWERON : 0;
+ /* DB1300: power always on, but don't tell when no card present */
+ if ((sock->board_type == BOARD_TYPE_DB1300) && (status & SS_DETECT))
+ status = SS_POWERON | SS_3VCARD | SS_DETECT;
+
/* reset de-asserted? then we're ready */
status |= (GET_RESET(cr, sock->nr)) ? SS_READY : SS_RESET;
@@ -418,6 +433,9 @@ static int __devinit db1x_pcmcia_socket_probe(struct platform_device *pdev)
case BCSR_WHOAMI_PB1200 ... BCSR_WHOAMI_DB1200:
sock->board_type = BOARD_TYPE_DB1200;
break;
+ case BCSR_WHOAMI_DB1300:
+ sock->board_type = BOARD_TYPE_DB1300;
+ break;
default:
printk(KERN_INFO "db1xxx-ss: unknown board %d!\n", bid);
ret = -ENODEV;
diff --git a/drivers/video/au1200fb.c b/drivers/video/au1200fb.c
index 7200559..6c4342f 100644
--- a/drivers/video/au1200fb.c
+++ b/drivers/video/au1200fb.c
@@ -639,6 +639,42 @@ static struct panel_settings known_lcd_panels[] =
856, 856,
480, 480,
},
+ [9] = {
+ .name = "DB1300_800x480",
+ .monspecs = {
+ .modedb = NULL,
+ .modedb_len = 0,
+ .hfmin = 30000,
+ .hfmax = 70000,
+ .vfmin = 60,
+ .vfmax = 60,
+ .dclkmin = 6000000,
+ .dclkmax = 28000000,
+ .input = FB_DISP_RGB,
+ },
+ .mode_screen = LCD_SCREEN_SX_N(800) |
+ LCD_SCREEN_SY_N(480),
+ .mode_horztiming = LCD_HORZTIMING_HPW_N(5) |
+ LCD_HORZTIMING_HND1_N(16) |
+ LCD_HORZTIMING_HND2_N(8),
+ .mode_verttiming = LCD_VERTTIMING_VPW_N(4) |
+ LCD_VERTTIMING_VND1_N(8) |
+ LCD_VERTTIMING_VND2_N(5),
+ .mode_clkcontrol = LCD_CLKCONTROL_PCD_N(1) |
+ LCD_CLKCONTROL_IV |
+ LCD_CLKCONTROL_IH,
+ .mode_pwmdiv = 0x00000000,
+ .mode_pwmhi = 0x00000000,
+ .mode_outmask = 0x00FFFFFF,
+ .mode_fifoctrl = 0x2f2f2f2f,
+ .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
+ .mode_backlight = 0x00000000,
+ .mode_auxpll = (48/12) * 2,
+ .device_init = board_au1200fb_panel_init,
+ .device_shutdown = board_au1200fb_panel_shutdown,
+ 800, 800,
+ 480, 480,
+ },
};
#define NUM_PANELS (ARRAY_SIZE(known_lcd_panels))
diff --git a/sound/soc/au1x/Kconfig b/sound/soc/au1x/Kconfig
index 93323cc..5981ecc 100644
--- a/sound/soc/au1x/Kconfig
+++ b/sound/soc/au1x/Kconfig
@@ -51,12 +51,14 @@ config SND_SOC_DB1000
of boards (DB1000/DB1500/DB1100).
config SND_SOC_DB1200
- tristate "DB1200 AC97+I2S audio support"
- depends on SND_SOC_AU1XPSC
+ tristate "DB1200/DB1300 Audio support"
+ select SND_SOC_AU1XPSC
select SND_SOC_AU1XPSC_AC97
select SND_SOC_AC97_CODEC
+ select SND_SOC_WM9712
select SND_SOC_AU1XPSC_I2S
select SND_SOC_WM8731
help
- Select this option to enable audio (AC97 or I2S) on the
- Alchemy/AMD/RMI DB1200 demoboard.
+ Select this option to enable audio (AC97 and I2S) on the
+ Alchemy/AMD/RMI/NetLogic Db1200 and Db1300 evaluation boards.
+ If you need Db1300 touchscreen support, you definitely want to say Y.
diff --git a/sound/soc/au1x/db1200.c b/sound/soc/au1x/db1200.c
index 289312c..ca2335a 100644
--- a/sound/soc/au1x/db1200.c
+++ b/sound/soc/au1x/db1200.c
@@ -1,5 +1,5 @@
/*
- * DB1200 ASoC audio fabric support code.
+ * DB1200/DB1300 ASoC audio fabric support code.
*
* (c) 2008-2011 Manuel Lauss <manuel.lauss@googlemail.com>
*
@@ -28,6 +28,12 @@ static struct platform_device_id db1200_pids[] = {
}, {
.name = "db1200-i2s",
.driver_data = 1,
+ }, {
+ .name = "db1300-ac97",
+ .driver_data = 2,
+ }, {
+ .name = "db1300-i2s",
+ .driver_data = 3,
},
{},
};
@@ -49,6 +55,21 @@ static struct snd_soc_card db1200_ac97_machine = {
.num_links = 1,
};
+static struct snd_soc_dai_link db1300_ac97_dai = {
+ .name = "AC97",
+ .stream_name = "AC97 HiFi",
+ .codec_dai_name = "wm9712-hifi",
+ .cpu_dai_name = "au1xpsc_ac97.1",
+ .platform_name = "au1xpsc-pcm.1",
+ .codec_name = "wm9712-codec.1",
+};
+
+static struct snd_soc_card db1300_ac97_machine = {
+ .name = "DB1300_AC97",
+ .dai_link = &db1300_ac97_dai,
+ .num_links = 1,
+};
+
/*------------------------- I2S PART ---------------------------*/
static int db1200_i2s_startup(struct snd_pcm_substream *substream)
@@ -98,11 +119,29 @@ static struct snd_soc_card db1200_i2s_machine = {
.num_links = 1,
};
+static struct snd_soc_dai_link db1300_i2s_dai = {
+ .name = "WM8731",
+ .stream_name = "WM8731 PCM",
+ .codec_dai_name = "wm8731-hifi",
+ .cpu_dai_name = "au1xpsc_i2s.2",
+ .platform_name = "au1xpsc-pcm.2",
+ .codec_name = "wm8731.0-001b",
+ .ops = &db1200_i2s_wm8731_ops,
+};
+
+static struct snd_soc_card db1300_i2s_machine = {
+ .name = "DB1300_I2S",
+ .dai_link = &db1300_i2s_dai,
+ .num_links = 1,
+};
+
/*------------------------- COMMON PART ---------------------------*/
static struct snd_soc_card *db1200_cards[] __devinitdata = {
&db1200_ac97_machine,
&db1200_i2s_machine,
+ &db1300_ac97_machine,
+ &db1300_i2s_machine,
};
static int __devinit db1200_audio_probe(struct platform_device *pdev)
@@ -147,5 +186,5 @@ module_init(db1200_audio_load);
module_exit(db1200_audio_unload);
MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("DB1200 ASoC audio support");
+MODULE_DESCRIPTION("DB1200/DB1300 ASoC audio support");
MODULE_AUTHOR("Manuel Lauss");
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 06/18] MIPS: Alchemy: better DB1550 support
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (4 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 05/18] MIPS: Alchemy: DB1300 support Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 07/18] MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files Manuel Lauss
` (11 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Improved DB1550 support, with audio and serial busses.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Kconfig | 2 +-
arch/mips/alchemy/devboards/Makefile | 2 +-
arch/mips/alchemy/devboards/db1550.c | 506 ++++++++++++++++++++++
arch/mips/alchemy/devboards/db1x00/board_setup.c | 24 +-
arch/mips/alchemy/devboards/db1x00/platform.c | 61 +---
arch/mips/configs/db1550_defconfig | 288 +++++++++----
arch/mips/include/asm/mach-db1x00/bcsr.h | 2 +-
arch/mips/include/asm/mach-db1x00/db1x00.h | 16 -
sound/soc/au1x/Kconfig | 4 +-
sound/soc/au1x/db1200.c | 34 ++-
10 files changed, 763 insertions(+), 176 deletions(-)
create mode 100644 arch/mips/alchemy/devboards/db1550.c
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index f9a13be..a1b995f 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -71,7 +71,7 @@ config MIPS_DB1550
bool "Alchemy DB1550 board"
select ALCHEMY_GPIOINT_AU1000
select HW_HAS_PCI
- select DMA_NONCOHERENT
+ select DMA_COHERENT
select MIPS_DISABLE_OBSOLETE_IDE
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 2eb75c9..3467ec9 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -13,4 +13,4 @@ obj-$(CONFIG_MIPS_DB1100) += db1x00/
obj-$(CONFIG_MIPS_DB1200) += db1200/
obj-$(CONFIG_MIPS_DB1300) += db1300.o
obj-$(CONFIG_MIPS_DB1500) += db1x00/
-obj-$(CONFIG_MIPS_DB1550) += db1x00/
+obj-$(CONFIG_MIPS_DB1550) += db1550.o
diff --git a/arch/mips/alchemy/devboards/db1550.c b/arch/mips/alchemy/devboards/db1550.c
new file mode 100644
index 0000000..a4755b0
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1550.c
@@ -0,0 +1,506 @@
+/*
+ * Alchemy Db1550 board support
+ *
+ * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "DB1550";
+}
+
+static void __init db1550_hw_setup(void)
+{
+ void __iomem *base;
+
+ alchemy_gpio_direction_output(203, 0); /* red led on */
+
+ /* complete SPI setup: link psc0_intclk to a 48MHz source,
+ * and assign GPIO16 to PSC0_SYNC1 (SPI cs# line)
+ */
+ base = (void __iomem *)SYS_CLKSRC;
+ __raw_writel(__raw_readl(base) | 0x000001e0, base);
+ base = (void __iomem *)SYS_PINFUNC;
+ __raw_writel(__raw_readl(base) | 1, base);
+ wmb();
+
+ /* reset the AC97 codec now, the reset time in the psc-ac97 driver
+ * is apparently too short although it's ridiculous as it is.
+ */
+ base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
+ __raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
+ base + PSC_SEL_OFFSET);
+ __raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
+ wmb();
+ __raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
+ wmb();
+
+ alchemy_gpio_direction_output(202, 0); /* green led on */
+}
+
+void __init board_setup(void)
+{
+ unsigned short whoami;
+
+ bcsr_init(DB1550_BCSR_PHYS_ADDR,
+ DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "Alchemy/AMD DB1550 Board, CPLD Rev %d"
+ " Board-ID %d Daughtercard ID %d\n",
+ (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+ db1550_hw_setup();
+}
+
+/*****************************************************************************/
+
+static struct mtd_partition db1550_spiflash_parts[] = {
+ {
+ .name = "spi_flash",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct flash_platform_data db1550_spiflash_data = {
+ .name = "s25fl010",
+ .parts = db1550_spiflash_parts,
+ .nr_parts = ARRAY_SIZE(db1550_spiflash_parts),
+ .type = "m25p10",
+};
+
+static struct spi_board_info db1550_spi_devs[] __initdata = {
+ {
+ /* TI TMP121AIDBVR temp sensor */
+ .modalias = "tmp121",
+ .max_speed_hz = 2400000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ },
+ {
+ /* Spansion S25FL001D0FMA SPI flash */
+ .modalias = "m25p80",
+ .max_speed_hz = 2400000,
+ .bus_num = 0,
+ .chip_select = 1,
+ .mode = SPI_MODE_0,
+ .platform_data = &db1550_spiflash_data,
+ },
+};
+
+static struct i2c_board_info db1550_i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("24c04", 0x52),}, /* AT24C04-10 I2C eeprom */
+ { I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
+ { I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1550_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1550_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1550_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1550_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1550_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1550_nand_parts),
+ .partitions = db1550_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1550_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1550_nand_device_ready,
+ .cmd_ctrl = au1550_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1550_nand_res[] = {
+ [0] = {
+ .start = 0x20000000,
+ .end = 0x200000ff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1550_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1550_nand_res),
+ .resource = db1550_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1550_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC0_INT,
+ .end = AU1550_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC0_TX,
+ .end = AU1550_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC0_RX,
+ .end = AU1550_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+ if (cs)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1550_spi_platdata = {
+ .mainclk_hz = 48000000, /* PSC0 clock: max. 2.4MHz SPI clk */
+ .num_chipselect = 2,
+ .activate_cs = db1550_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1550_spi_dev = {
+ .dev = {
+ .dma_mask = &spi_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1550_spi_platdata,
+ },
+ .name = "au1550-spi",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1550_psc0_res),
+ .resource = au1550_psc0_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc1_res[] = {
+ [0] = {
+ .start = AU1550_PSC1_PHYS_ADDR,
+ .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC1_INT,
+ .end = AU1550_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC1_TX,
+ .end = AU1550_DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC1_RX,
+ .end = AU1550_DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1550_ac97_dev = {
+ .name = "au1xpsc_ac97",
+ .id = 1, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1550_psc1_res),
+ .resource = au1550_psc1_res,
+};
+
+
+static struct resource au1550_psc2_res[] = {
+ [0] = {
+ .start = AU1550_PSC2_PHYS_ADDR,
+ .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC2_INT,
+ .end = AU1550_PSC2_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC2_TX,
+ .end = AU1550_DSCR_CMD0_PSC2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC2_RX,
+ .end = AU1550_DSCR_CMD0_PSC2_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1550_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1550_psc2_res),
+ .resource = au1550_psc2_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc3_res[] = {
+ [0] = {
+ .start = AU1550_PSC3_PHYS_ADDR,
+ .end = AU1550_PSC3_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC3_INT,
+ .end = AU1550_PSC3_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC3_TX,
+ .end = AU1550_DSCR_CMD0_PSC3_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC3_RX,
+ .end = AU1550_DSCR_CMD0_PSC3_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1550_i2s_dev = {
+ .name = "au1xpsc_i2s",
+ .id = 3, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1550_psc3_res),
+ .resource = au1550_psc3_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1550_stac_dev = {
+ .name = "ac97-codec",
+ .id = 1, /* on PSC1 */
+};
+
+static struct platform_device db1550_ac97dma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 1, /* on PSC3 */
+};
+
+static struct platform_device db1550_i2sdma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 3, /* on PSC3 */
+};
+
+static struct platform_device db1550_sndac97_dev = {
+ .name = "db1550-ac97",
+};
+
+static struct platform_device db1550_sndi2s_dev = {
+ .name = "db1550-i2s",
+};
+
+/**********************************************************************/
+
+static struct platform_device db1550_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 11) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 11)
+ return (pin == 1) ? AU1550_PCI_INTC : 0xff;
+ if (slot == 12) {
+ switch (pin) {
+ case 1: return AU1550_PCI_INTB;
+ case 2: return AU1550_PCI_INTC;
+ case 3: return AU1550_PCI_INTD;
+ case 4: return AU1550_PCI_INTA;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1550_PCI_INTA;
+ case 2: return AU1550_PCI_INTB;
+ case 3: return AU1550_PCI_INTC;
+ case 4: return AU1550_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata db1550_pci_pd = {
+ .board_map_irq = db1550_map_pci_irq,
+};
+
+static struct platform_device db1550_pci_host_dev = {
+ .dev.platform_data = &db1550_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device *db1550_devs[] __initdata = {
+ &db1550_rtc_dev,
+ &db1550_nand_dev,
+ &db1550_i2c_dev,
+ &db1550_ac97_dev,
+ &db1550_spi_dev,
+ &db1550_i2s_dev,
+ &db1550_stac_dev,
+ &db1550_ac97dma_dev,
+ &db1550_i2sdma_dev,
+ &db1550_sndac97_dev,
+ &db1550_sndi2s_dev,
+};
+
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+static int __init db1550_pci_init(void)
+{
+ return platform_device_register(&db1550_pci_host_dev);
+}
+arch_initcall(db1550_pci_init);
+
+static int __init db1550_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH); /* CD0# */
+ irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH); /* CD1# */
+ irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW); /* CARD0# */
+ irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW); /* CARD1# */
+ irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
+ irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
+
+ i2c_register_board_info(0, db1550_i2c_devs,
+ ARRAY_SIZE(db1550_i2c_devs));
+ spi_register_board_info(db1550_spi_devs,
+ ARRAY_SIZE(db1550_i2c_devs));
+
+ /* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ /* SPI/I2C use internally supplied 50MHz source */
+ __raw_writel(PSC_SEL_CLK_INTCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ __raw_writel(PSC_SEL_CLK_INTCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1550_GPIO3_INT, AU1550_GPIO0_INT,
+ /*AU1550_GPIO21_INT*/0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ AU1550_GPIO5_INT, AU1550_GPIO1_INT,
+ /*AU1550_GPIO22_INT*/0, 0, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(128 << 20, 4, swapped);
+
+ return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));
+}
+device_initcall(db1550_dev_init);
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
index 8a222b3..2dbebcb 100644
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ b/arch/mips/alchemy/devboards/db1x00/board_setup.c
@@ -48,11 +48,6 @@ const char *get_system_type(void)
void __init board_setup(void)
{
- unsigned long bcsr1, bcsr2;
-
- bcsr1 = DB1000_BCSR_PHYS_ADDR;
- bcsr2 = DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS;
-
#ifdef CONFIG_MIPS_DB1000
printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
#endif
@@ -62,15 +57,9 @@ void __init board_setup(void)
#ifdef CONFIG_MIPS_DB1100
printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
#endif
-#ifdef CONFIG_MIPS_DB1550
- printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
-
- bcsr1 = DB1550_BCSR_PHYS_ADDR;
- bcsr2 = DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS;
-#endif
-
/* initialize board register space */
- bcsr_init(bcsr1, bcsr2);
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
{
@@ -92,14 +81,7 @@ void __init board_setup(void)
static int __init db1x00_init_irq(void)
{
-#if defined(CONFIG_MIPS_DB1550)
- irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1550_GPIO3_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1550_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1550_GPIO21_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1550_GPIO22_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1500)
+#if defined(CONFIG_MIPS_DB1500)
irq_set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
irq_set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
irq_set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
index a8bb4fa..b439b4f 100644
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ b/arch/mips/alchemy/devboards/db1x00/platform.c
@@ -33,7 +33,6 @@ struct pci_dev;
* CD0/1 GPIO0/3
* STSCHG0/1 GPIO1/4
* CARD0/1 GPIO2/5
- * Db1550: 0/1, 21/22, 3/5
*/
#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
@@ -45,7 +44,6 @@ struct pci_dev;
#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
-#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
#elif defined(CONFIG_MIPS_DB1100)
#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
@@ -53,7 +51,6 @@ struct pci_dev;
#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
-#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
#elif defined(CONFIG_MIPS_DB1500)
#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
@@ -61,20 +58,8 @@ struct pci_dev;
#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
-#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
-#elif defined(CONFIG_MIPS_DB1550)
-#define DB1XXX_PCMCIA_CD0 AU1550_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1550_GPIO21_INT
-#define DB1XXX_PCMCIA_CARD0 AU1550_GPIO3_INT
-#define DB1XXX_PCMCIA_CD1 AU1550_GPIO1_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1550_GPIO22_INT
-#define DB1XXX_PCMCIA_CARD1 AU1550_GPIO5_INT
-#define BOARD_FLASH_SIZE 0x08000000 /* 128MB */
-#endif
-#ifdef CONFIG_PCI
-#ifdef CONFIG_MIPS_DB1500
-static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
{
if ((slot < 12) || (slot > 13) || pin == 0)
return -1;
@@ -90,34 +75,6 @@ static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
}
return -1;
}
-#endif
-
-#ifdef CONFIG_MIPS_DB1550
-static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 11) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 11)
- return (pin == 1) ? AU1550_PCI_INTC : 0xff;
- if (slot == 12) {
- switch (pin) {
- case 1: return AU1550_PCI_INTB;
- case 2: return AU1550_PCI_INTC;
- case 3: return AU1550_PCI_INTD;
- case 4: return AU1550_PCI_INTA;
- }
- }
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1550_PCI_INTA;
- case 2: return AU1550_PCI_INTB;
- case 3: return AU1550_PCI_INTC;
- case 4: return AU1550_PCI_INTD;
- }
- }
- return -1;
-}
-#endif
static struct resource alchemy_pci_host_res[] = {
[0] = {
@@ -127,24 +84,24 @@ static struct resource alchemy_pci_host_res[] = {
},
};
-static struct alchemy_pci_platdata db1xxx_pci_pd = {
- .board_map_irq = db1xxx_map_pci_irq,
+static struct alchemy_pci_platdata db1500_pci_pd = {
+ .board_map_irq = db1500_map_pci_irq,
};
-static struct platform_device db1xxx_pci_host_dev = {
- .dev.platform_data = &db1xxx_pci_pd,
+static struct platform_device db1500_pci_host_dev = {
+ .dev.platform_data = &db1500_pci_pd,
.name = "alchemy-pci",
.id = 0,
.num_resources = ARRAY_SIZE(alchemy_pci_host_res),
.resource = alchemy_pci_host_res,
};
-static int __init db15x0_pci_init(void)
+static int __init db1500_pci_init(void)
{
- return platform_device_register(&db1xxx_pci_host_dev);
+ return platform_device_register(&db1500_pci_host_dev);
}
/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
-arch_initcall(db15x0_pci_init);
+arch_initcall(db1500_pci_init);
#endif
#ifdef CONFIG_MIPS_DB1100
@@ -243,7 +200,7 @@ static int __init db1xxx_dev_init(void)
platform_device_register(&alchemy_ac97c_dev);
platform_device_register(&db1x00_audio_dev);
- db1x_register_norflash(BOARD_FLASH_SIZE, 4 /* 32bit */, F_SWAPPED);
+ db1x_register_norflash(0x02000000, 4 /* 32bit */, F_SWAPPED);
return 0;
}
device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/configs/db1550_defconfig b/arch/mips/configs/db1550_defconfig
index 798a553..36cda27 100644
--- a/arch/mips/configs/db1550_defconfig
+++ b/arch/mips/configs/db1550_defconfig
@@ -1,145 +1,262 @@
+CONFIG_MIPS=y
CONFIG_MIPS_ALCHEMY=y
CONFIG_MIPS_DB1550=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_HZ_100=y
-# CONFIG_SECCOMP is not set
+CONFIG_HZ=100
CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION="-db1550"
+CONFIG_LOCALVERSION_AUTO=y
CONFIG_KERNEL_LZMA=y
+CONFIG_DEFAULT_HOSTNAME="db1550"
+CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+CONFIG_FHANDLE=y
+CONFIG_AUDIT=y
CONFIG_TINY_RCU=y
-CONFIG_LOG_BUF_SHIFT=14
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+CONFIG_USER_NS=y
+CONFIG_PID_NS=y
+CONFIG_NET_NS=y
CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_KALLSYMS is not set
-# CONFIG_PCSPKR_PLATFORM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_EMBEDDED=y
+CONFIG_PCI_QUIRKS=y
CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+CONFIG_BLK_DEV_BSG=y
+CONFIG_BLK_DEV_BSGLIB=y
+CONFIG_IOSCHED_NOOP=y
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
CONFIG_PCI=y
CONFIG_PCCARD=y
-# CONFIG_CARDBUS is not set
+CONFIG_PCMCIA=y
+CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
-CONFIG_PM=y
+CONFIG_BINFMT_ELF=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_BINFMT_MISC=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_PM_SLEEP=y
CONFIG_PM_RUNTIME=y
+CONFIG_PM=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
+CONFIG_XFRM=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_LRO=y
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+CONFIG_IPV6=y
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_DNS_RESOLVER=y
+CONFIG_UEVENT_HELPER_PATH=""
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_UTIL=y
CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_AU1550=y
-CONFIG_BLK_DEV_UB=y
-# CONFIG_MISC_DEVICES is not set
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECS=y
-CONFIG_BLK_DEV_IDECD=y
-# CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS is not set
-CONFIG_IDE_TASK_IOCTL=y
-# CONFIG_IDEPCI_PCIBUS_ORDER is not set
-CONFIG_BLK_DEV_HPT366=y
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_MISC_DEVICES=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI_MOD=y
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_MULTI_LUN=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_ATA=y
+CONFIG_ATA_SFF=y
+CONFIG_ATA_BMDMA=y
+CONFIG_PATA_HPT37X=y
+CONFIG_PATA_PCMCIA=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_DM=y
CONFIG_NETDEVICES=y
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-CONFIG_BROADCOM_PHY=y
-CONFIG_ICPLUS_PHY=y
-CONFIG_REALTEK_PHY=y
-CONFIG_NATIONAL_PHY=y
-CONFIG_STE10XP=y
-CONFIG_LSI_ET1011C_PHY=y
-CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+CONFIG_PHYLIB=y
+CONFIG_NET_ETHERNET=y
CONFIG_MIPS_AU1X00_ENET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_NET_PCMCIA=y
+CONFIG_PCMCIA_3C589=y
+CONFIG_PCMCIA_PCNET=y
+CONFIG_INPUT=y
CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
+CONFIG_DEVKMEM=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_DEVPORT=y
CONFIG_I2C=y
-# CONFIG_I2C_COMPAT is not set
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
-# CONFIG_I2C_HELPER_AUTO is not set
CONFIG_I2C_AU1550=y
CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
CONFIG_SPI_AU1550=y
-# CONFIG_HWMON is not set
-# CONFIG_VGA_ARB is not set
-# CONFIG_VGA_CONSOLE is not set
+CONFIG_SPI_BITBANG=y
+CONFIG_HWMON=y
+CONFIG_SENSORS_ADM1025=y
+CONFIG_SENSORS_LM70=y
+CONFIG_DUMMY_CONSOLE=y
CONFIG_SOUND=y
CONFIG_SND=y
-CONFIG_SND_HRTIMER=y
-CONFIG_SND_DYNAMIC_MINORS=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_PCI is not set
-# CONFIG_SND_SPI is not set
-# CONFIG_SND_MIPS is not set
-# CONFIG_SND_PCMCIA is not set
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=y
CONFIG_SND_SOC=y
+CONFIG_SND_SOC_AC97_BUS=y
CONFIG_SND_SOC_AU1XPSC=y
-# CONFIG_HID_SUPPORT is not set
+CONFIG_SND_SOC_AU1XPSC_I2S=y
+CONFIG_SND_SOC_AU1XPSC_AC97=y
+CONFIG_SND_SOC_DB1200=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+CONFIG_SND_SOC_AC97_CODEC=y
+CONFIG_SND_SOC_WM8731=y
+CONFIG_SND_SOC_WM9712=y
+CONFIG_AC97_BUS=y
CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_DRV_AU1XXX=y
-CONFIG_EXT2_FS=y
-# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_USE_FOR_EXT23=y
+CONFIG_EXT4_FS_XATTR=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_JBD2=y
+CONFIG_FS_MBCACHE=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_EXPORTFS=y
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_CONFIGFS_FS=y
+CONFIG_MISC_FILESYSTEMS=y
CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
CONFIG_JFFS2_SUMMARY=y
CONFIG_JFFS2_FS_XATTR=y
-# CONFIG_JFFS2_FS_POSIX_ACL is not set
-# CONFIG_JFFS2_FS_SECURITY is not set
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
CONFIG_JFFS2_RUBIN=y
+CONFIG_JFFS2_CMODE_PRIORITY=y
CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_ZLIB=y
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_PNFS_FILE_LAYOUT=y
+CONFIG_PNFS_BLOCK=y
CONFIG_ROOT_NFS=y
+CONFIG_NFS_USE_KERNEL_DNS=y
+CONFIG_NFS_USE_NEW_IDMAPPER=y
+CONFIG_NFSD=y
+CONFIG_NFSD_V2_ACL=y
+CONFIG_NFSD_V3=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_SUNRPC_BACKCHANNEL=y
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_CODEPAGE_852=y
@@ -148,10 +265,21 @@ CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_15=y
CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_ZBOOT=y
+CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
+CONFIG_FRAME_WARN=1024
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="noirqdebug console=ttyS0,115200 root=/dev/sda1 rootfstype=ext4"
CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITYFS=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_BITREVERSE=y
+CONFIG_CRC16=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC32=y
+CONFIG_AUDIT_GENERIC=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_BCH=y
+CONFIG_NLATTR=y
diff --git a/arch/mips/include/asm/mach-db1x00/bcsr.h b/arch/mips/include/asm/mach-db1x00/bcsr.h
index 0ef6300..bb9fc23 100644
--- a/arch/mips/include/asm/mach-db1x00/bcsr.h
+++ b/arch/mips/include/asm/mach-db1x00/bcsr.h
@@ -163,7 +163,7 @@ enum bcsr_whoami_boards {
#define BCSR_BOARD_GPIO200RST 0x0400
#define BCSR_BOARD_PCICLKOUT 0x0800
#define BCSR_BOARD_PCICFG 0x1000
-#define BCSR_BOARD_SPISEL 0x4000 /* PB/DB1550 */
+#define BCSR_BOARD_SPISEL 0x2000 /* PB/DB1550 */
#define BCSR_BOARD_SD0WP 0x4000 /* DB1100 */
#define BCSR_BOARD_SD1WP 0x8000 /* DB1100 */
diff --git a/arch/mips/include/asm/mach-db1x00/db1x00.h b/arch/mips/include/asm/mach-db1x00/db1x00.h
index a5affb0..51f1ebf 100644
--- a/arch/mips/include/asm/mach-db1x00/db1x00.h
+++ b/arch/mips/include/asm/mach-db1x00/db1x00.h
@@ -29,22 +29,6 @@
#include <asm/mach-au1x00/au1xxx_psc.h>
-#ifdef CONFIG_MIPS_DB1550
-
-#define DBDMA_AC97_TX_CHAN AU1550_DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN AU1550_DSCR_CMD0_PSC1_RX
-#define DBDMA_I2S_TX_CHAN AU1550_DSCR_CMD0_PSC3_TX
-#define DBDMA_I2S_RX_CHAN AU1550_DSCR_CMD0_PSC3_RX
-
-#define SPI_PSC_BASE AU1550_PSC0_PHYS_ADDR
-#define AC97_PSC_BASE AU1550_PSC1_PHYS_ADDR
-#define SMBUS_PSC_BASE AU1550_PSC2_PHYS_ADDR
-#define I2S_PSC_BASE AU1550_PSC3_PHYS_ADDR
-
-#define NAND_PHYS_ADDR 0x20000000
-
-#endif
-
/*
* NAND defines
*
diff --git a/sound/soc/au1x/Kconfig b/sound/soc/au1x/Kconfig
index 5981ecc..c620cbf9 100644
--- a/sound/soc/au1x/Kconfig
+++ b/sound/soc/au1x/Kconfig
@@ -51,7 +51,7 @@ config SND_SOC_DB1000
of boards (DB1000/DB1500/DB1100).
config SND_SOC_DB1200
- tristate "DB1200/DB1300 Audio support"
+ tristate "DB1200/DB1300/DB1550 Audio support"
select SND_SOC_AU1XPSC
select SND_SOC_AU1XPSC_AC97
select SND_SOC_AC97_CODEC
@@ -60,5 +60,5 @@ config SND_SOC_DB1200
select SND_SOC_WM8731
help
Select this option to enable audio (AC97 and I2S) on the
- Alchemy/AMD/RMI/NetLogic Db1200 and Db1300 evaluation boards.
+ Alchemy/AMD/RMI/NetLogic Db1200, Db1550 and Db1300 evaluation boards.
If you need Db1300 touchscreen support, you definitely want to say Y.
diff --git a/sound/soc/au1x/db1200.c b/sound/soc/au1x/db1200.c
index ca2335a..44ad118 100644
--- a/sound/soc/au1x/db1200.c
+++ b/sound/soc/au1x/db1200.c
@@ -1,5 +1,5 @@
/*
- * DB1200/DB1300 ASoC audio fabric support code.
+ * DB1200/DB1300/DB1550 ASoC audio fabric support code.
*
* (c) 2008-2011 Manuel Lauss <manuel.lauss@googlemail.com>
*
@@ -34,6 +34,12 @@ static struct platform_device_id db1200_pids[] = {
}, {
.name = "db1300-i2s",
.driver_data = 3,
+ }, {
+ .name = "db1550-ac97",
+ .driver_data = 4,
+ }, {
+ .name = "db1550-i2s",
+ .driver_data = 5,
},
{},
};
@@ -70,6 +76,12 @@ static struct snd_soc_card db1300_ac97_machine = {
.num_links = 1,
};
+static struct snd_soc_card db1550_ac97_machine = {
+ .name = "DB1550_AC97",
+ .dai_link = &db1200_ac97_dai,
+ .num_links = 1,
+};
+
/*------------------------- I2S PART ---------------------------*/
static int db1200_i2s_startup(struct snd_pcm_substream *substream)
@@ -135,6 +147,22 @@ static struct snd_soc_card db1300_i2s_machine = {
.num_links = 1,
};
+static struct snd_soc_dai_link db1550_i2s_dai = {
+ .name = "WM8731",
+ .stream_name = "WM8731 PCM",
+ .codec_dai_name = "wm8731-hifi",
+ .cpu_dai_name = "au1xpsc_i2s.3",
+ .platform_name = "au1xpsc-pcm.3",
+ .codec_name = "wm8731.0-001b",
+ .ops = &db1200_i2s_wm8731_ops,
+};
+
+static struct snd_soc_card db1550_i2s_machine = {
+ .name = "DB1550_I2S",
+ .dai_link = &db1550_i2s_dai,
+ .num_links = 1,
+};
+
/*------------------------- COMMON PART ---------------------------*/
static struct snd_soc_card *db1200_cards[] __devinitdata = {
@@ -142,6 +170,8 @@ static struct snd_soc_card *db1200_cards[] __devinitdata = {
&db1200_i2s_machine,
&db1300_ac97_machine,
&db1300_i2s_machine,
+ &db1550_ac97_machine,
+ &db1550_i2s_machine,
};
static int __devinit db1200_audio_probe(struct platform_device *pdev)
@@ -186,5 +216,5 @@ module_init(db1200_audio_load);
module_exit(db1200_audio_unload);
MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("DB1200/DB1300 ASoC audio support");
+MODULE_DESCRIPTION("DB1200/DB1300/DB1550 ASoC audio support");
MODULE_AUTHOR("Manuel Lauss");
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 07/18] MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (5 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 06/18] MIPS: Alchemy: better DB1550 support Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 08/18] MIPS: Alchemy: merge devboard code into single per-board files Manuel Lauss
` (10 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Most of these files are have more comments than real code; merge
them all into single board-<name>.c files.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Makefile | 3 +
arch/mips/alchemy/Platform | 8 +-
arch/mips/alchemy/board-gpr.c | 303 ++++++++++++++++++++++++++++++
arch/mips/alchemy/board-mtx1.c | 313 +++++++++++++++++++++++++++++++
arch/mips/alchemy/board-xxs1500.c | 154 +++++++++++++++
arch/mips/alchemy/gpr/Makefile | 8 -
arch/mips/alchemy/gpr/board_setup.c | 75 --------
arch/mips/alchemy/gpr/init.c | 63 ------
arch/mips/alchemy/gpr/platform.c | 230 -----------------------
arch/mips/alchemy/mtx-1/Makefile | 9 -
arch/mips/alchemy/mtx-1/board_setup.c | 94 ---------
arch/mips/alchemy/mtx-1/init.c | 66 -------
arch/mips/alchemy/mtx-1/platform.c | 230 -----------------------
arch/mips/alchemy/xxs1500/Makefile | 8 -
arch/mips/alchemy/xxs1500/board_setup.c | 93 ---------
arch/mips/alchemy/xxs1500/init.c | 63 ------
arch/mips/alchemy/xxs1500/platform.c | 63 ------
17 files changed, 777 insertions(+), 1006 deletions(-)
create mode 100644 arch/mips/alchemy/Makefile
create mode 100644 arch/mips/alchemy/board-gpr.c
create mode 100644 arch/mips/alchemy/board-mtx1.c
create mode 100644 arch/mips/alchemy/board-xxs1500.c
delete mode 100644 arch/mips/alchemy/gpr/Makefile
delete mode 100644 arch/mips/alchemy/gpr/board_setup.c
delete mode 100644 arch/mips/alchemy/gpr/init.c
delete mode 100644 arch/mips/alchemy/gpr/platform.c
delete mode 100644 arch/mips/alchemy/mtx-1/Makefile
delete mode 100644 arch/mips/alchemy/mtx-1/board_setup.c
delete mode 100644 arch/mips/alchemy/mtx-1/init.c
delete mode 100644 arch/mips/alchemy/mtx-1/platform.c
delete mode 100644 arch/mips/alchemy/xxs1500/Makefile
delete mode 100644 arch/mips/alchemy/xxs1500/board_setup.c
delete mode 100644 arch/mips/alchemy/xxs1500/init.c
delete mode 100644 arch/mips/alchemy/xxs1500/platform.c
diff --git a/arch/mips/alchemy/Makefile b/arch/mips/alchemy/Makefile
new file mode 100644
index 0000000..aac3b17
--- /dev/null
+++ b/arch/mips/alchemy/Makefile
@@ -0,0 +1,3 @@
+obj-$(CONFIG_MIPS_GPR) += board-gpr.o
+obj-$(CONFIG_MIPS_MTX1) += board-mtx1.o
+obj-$(CONFIG_MIPS_XXS1500) += board-xxs1500.o
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 4d13e21..c032f5b 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -75,21 +75,21 @@ cflags-$(CONFIG_MIPS_DB1300) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1300) += 0xffffffff80100000
#
-# 4G-Systems eval board
+# 4G-Systems MTX-1 "MeshCube" wireless router
#
-platform-$(CONFIG_MIPS_MTX1) += alchemy/mtx-1/
+platform-$(CONFIG_MIPS_MTX1) += alchemy/
load-$(CONFIG_MIPS_MTX1) += 0xffffffff80100000
#
# MyCable eval board
#
-platform-$(CONFIG_MIPS_XXS1500) += alchemy/xxs1500/
+platform-$(CONFIG_MIPS_XXS1500) += alchemy/
load-$(CONFIG_MIPS_XXS1500) += 0xffffffff80100000
#
# Trapeze ITS GRP board
#
-platform-$(CONFIG_MIPS_GPR) += alchemy/gpr/
+platform-$(CONFIG_MIPS_GPR) += alchemy/
load-$(CONFIG_MIPS_GPR) += 0xffffffff80100000
# boards can specify their own <gpio.h> in one of their include dirs.
diff --git a/arch/mips/alchemy/board-gpr.c b/arch/mips/alchemy/board-gpr.c
new file mode 100644
index 0000000..ba32590
--- /dev/null
+++ b/arch/mips/alchemy/board-gpr.c
@@ -0,0 +1,303 @@
+/*
+ * GPR board platform device registration (Au1550)
+ *
+ * Copyright (C) 2010 Wolfgang Grandegger <wg@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+ return "GPR";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtoul(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void gpr_reset(char *c)
+{
+ /* switch System-LED to orange (red# and green# on) */
+ alchemy_gpio_direction_output(4, 0);
+ alchemy_gpio_direction_output(5, 0);
+
+ /* trigger watchdog to reset board in 200ms */
+ printk(KERN_EMERG "Triggering watchdog soft reset...\n");
+ raw_local_irq_disable();
+ alchemy_gpio_direction_output(1, 0);
+ udelay(1);
+ alchemy_gpio_set_value(1, 1);
+ while (1)
+ cpu_wait();
+}
+
+static void gpr_power_off(void)
+{
+ while (1)
+ cpu_wait();
+}
+
+void __init board_setup(void)
+{
+ printk(KERN_INFO "Trapeze ITS GPR board\n");
+
+ pm_power_off = gpr_power_off;
+ _machine_halt = gpr_power_off;
+ _machine_restart = gpr_reset;
+
+ /* Enable UART1/3 */
+ alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+ alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
+
+ /* Take away Reset of UMTS-card */
+ alchemy_gpio_direction_output(215, 1);
+}
+
+/*
+ * Watchdog
+ */
+static struct resource gpr_wdt_resource[] = {
+ [0] = {
+ .start = 1,
+ .end = 1,
+ .name = "gpr-adm6320-wdt",
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device gpr_wdt_device = {
+ .name = "adm6320-wdt",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(gpr_wdt_resource),
+ .resource = gpr_wdt_resource,
+};
+
+/*
+ * FLASH
+ *
+ * 0x00000000-0x00200000 : "kernel"
+ * 0x00200000-0x00a00000 : "rootfs"
+ * 0x01d00000-0x01f00000 : "config"
+ * 0x01c00000-0x01d00000 : "yamon"
+ * 0x01d00000-0x01d40000 : "yamon env vars"
+ * 0x00000000-0x00a00000 : "kernel+rootfs"
+ */
+static struct mtd_partition gpr_mtd_partitions[] = {
+ {
+ .name = "kernel",
+ .size = 0x00200000,
+ .offset = 0,
+ },
+ {
+ .name = "rootfs",
+ .size = 0x00800000,
+ .offset = MTDPART_OFS_APPEND,
+ .mask_flags = MTD_WRITEABLE,
+ },
+ {
+ .name = "config",
+ .size = 0x00200000,
+ .offset = 0x01d00000,
+ },
+ {
+ .name = "yamon",
+ .size = 0x00100000,
+ .offset = 0x01c00000,
+ },
+ {
+ .name = "yamon env vars",
+ .size = 0x00040000,
+ .offset = MTDPART_OFS_APPEND,
+ },
+ {
+ .name = "kernel+rootfs",
+ .size = 0x00a00000,
+ .offset = 0,
+ },
+};
+
+static struct physmap_flash_data gpr_flash_data = {
+ .width = 4,
+ .nr_parts = ARRAY_SIZE(gpr_mtd_partitions),
+ .parts = gpr_mtd_partitions,
+};
+
+static struct resource gpr_mtd_resource = {
+ .start = 0x1e000000,
+ .end = 0x1fffffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device gpr_mtd_device = {
+ .name = "physmap-flash",
+ .dev = {
+ .platform_data = &gpr_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &gpr_mtd_resource,
+};
+
+/*
+ * LEDs
+ */
+static struct gpio_led gpr_gpio_leds[] = {
+ { /* green */
+ .name = "gpr:green",
+ .gpio = 4,
+ .active_low = 1,
+ },
+ { /* red */
+ .name = "gpr:red",
+ .gpio = 5,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_led_platform_data gpr_led_data = {
+ .num_leds = ARRAY_SIZE(gpr_gpio_leds),
+ .leds = gpr_gpio_leds,
+};
+
+static struct platform_device gpr_led_devices = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpr_led_data,
+ }
+};
+
+/*
+ * I2C
+ */
+static struct i2c_gpio_platform_data gpr_i2c_data = {
+ .sda_pin = 209,
+ .sda_is_open_drain = 1,
+ .scl_pin = 210,
+ .scl_is_open_drain = 1,
+ .udelay = 2, /* ~100 kHz */
+ .timeout = HZ,
+};
+
+static struct platform_device gpr_i2c_device = {
+ .name = "i2c-gpio",
+ .id = -1,
+ .dev.platform_data = &gpr_i2c_data,
+};
+
+static struct i2c_board_info gpr_i2c_info[] __initdata = {
+ {
+ I2C_BOARD_INFO("lm83", 0x18),
+ .type = "lm83"
+ }
+};
+
+
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static int gpr_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot == 0) && (pin == 1))
+ return AU1550_PCI_INTA;
+ else if ((slot == 0) && (pin == 2))
+ return AU1550_PCI_INTB;
+
+ return 0xff;
+}
+
+static struct alchemy_pci_platdata gpr_pci_pd = {
+ .board_map_irq = gpr_map_pci_irq,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device gpr_pci_host_dev = {
+ .dev.platform_data = &gpr_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static struct platform_device *gpr_devices[] __initdata = {
+ &gpr_wdt_device,
+ &gpr_mtd_device,
+ &gpr_i2c_device,
+ &gpr_led_devices,
+};
+
+static int __init gpr_pci_init(void)
+{
+ return platform_device_register(&gpr_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(gpr_pci_init);
+
+
+static int __init gpr_dev_init(void)
+{
+ i2c_register_board_info(0, gpr_i2c_info, ARRAY_SIZE(gpr_i2c_info));
+
+ return platform_add_devices(gpr_devices, ARRAY_SIZE(gpr_devices));
+}
+device_initcall(gpr_dev_init);
diff --git a/arch/mips/alchemy/board-mtx1.c b/arch/mips/alchemy/board-mtx1.c
new file mode 100644
index 0000000..295f1a9
--- /dev/null
+++ b/arch/mips/alchemy/board-mtx1.c
@@ -0,0 +1,313 @@
+/*
+ * MTX-1 platform devices registration (Au1500)
+ *
+ * Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <mtd/mtd-abi.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+ return "MTX-1";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtoul(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void mtx1_reset(char *c)
+{
+ /* Jump to the reset vector */
+ __asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void mtx1_power_off(void)
+{
+ while (1)
+ asm volatile (
+ " .set mips32 \n"
+ " wait \n"
+ " .set mips0 \n");
+}
+
+void __init board_setup(void)
+{
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ /* Enable USB power switch */
+ alchemy_gpio_direction_output(204, 0);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+ /* Initialize sys_pinfunc */
+ au_writel(SYS_PF_NI2, SYS_PINFUNC);
+
+ /* Initialize GPIO */
+ au_writel(~0, KSEG1ADDR(AU1000_SYS_PHYS_ADDR) + SYS_TRIOUTCLR);
+ alchemy_gpio_direction_output(0, 0); /* Disable M66EN (PCI 66MHz) */
+ alchemy_gpio_direction_output(3, 1); /* Disable PCI CLKRUN# */
+ alchemy_gpio_direction_output(1, 1); /* Enable EXT_IO3 */
+ alchemy_gpio_direction_output(5, 0); /* Disable eth PHY TX_ER */
+
+ /* Enable LED and set it to green */
+ alchemy_gpio_direction_output(211, 1); /* green on */
+ alchemy_gpio_direction_output(212, 0); /* red off */
+
+ pm_power_off = mtx1_power_off;
+ _machine_halt = mtx1_power_off;
+ _machine_restart = mtx1_reset;
+
+ printk(KERN_INFO "4G Systems MTX-1 Board\n");
+}
+
+/******************************************************************************/
+
+static struct gpio_keys_button mtx1_gpio_button[] = {
+ {
+ .gpio = 207,
+ .code = BTN_0,
+ .desc = "System button",
+ }
+};
+
+static struct gpio_keys_platform_data mtx1_buttons_data = {
+ .buttons = mtx1_gpio_button,
+ .nbuttons = ARRAY_SIZE(mtx1_gpio_button),
+};
+
+static struct platform_device mtx1_button = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &mtx1_buttons_data,
+ }
+};
+
+static struct resource mtx1_wdt_res[] = {
+ [0] = {
+ .start = 215,
+ .end = 215,
+ .name = "mtx1-wdt-gpio",
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device mtx1_wdt = {
+ .name = "mtx1-wdt",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(mtx1_wdt_res),
+ .resource = mtx1_wdt_res,
+};
+
+static struct gpio_led default_leds[] = {
+ {
+ .name = "mtx1:green",
+ .gpio = 211,
+ }, {
+ .name = "mtx1:red",
+ .gpio = 212,
+ },
+};
+
+static struct gpio_led_platform_data mtx1_led_data = {
+ .num_leds = ARRAY_SIZE(default_leds),
+ .leds = default_leds,
+};
+
+static struct platform_device mtx1_gpio_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &mtx1_led_data,
+ }
+};
+
+static struct mtd_partition mtx1_mtd_partitions[] = {
+ {
+ .name = "filesystem",
+ .size = 0x01C00000,
+ .offset = 0,
+ },
+ {
+ .name = "yamon",
+ .size = 0x00100000,
+ .offset = MTDPART_OFS_APPEND,
+ .mask_flags = MTD_WRITEABLE,
+ },
+ {
+ .name = "kernel",
+ .size = 0x002c0000,
+ .offset = MTDPART_OFS_APPEND,
+ },
+ {
+ .name = "yamon env",
+ .size = 0x00040000,
+ .offset = MTDPART_OFS_APPEND,
+ },
+};
+
+static struct physmap_flash_data mtx1_flash_data = {
+ .width = 4,
+ .nr_parts = 4,
+ .parts = mtx1_mtd_partitions,
+};
+
+static struct resource mtx1_mtd_resource = {
+ .start = 0x1e000000,
+ .end = 0x1fffffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device mtx1_mtd = {
+ .name = "physmap-flash",
+ .dev = {
+ .platform_data = &mtx1_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &mtx1_mtd_resource,
+};
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static int mtx1_pci_idsel(unsigned int devsel, int assert)
+{
+ /* This function is only necessary to support a proprietary Cardbus
+ * adapter on the mtx-1 "singleboard" variant. It triggers a custom
+ * logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
+ */
+ if (assert && devsel != 0)
+ /* Suppress signal to Cardbus */
+ alchemy_gpio_set_value(1, 0); /* set EXT_IO3 OFF */
+ else
+ alchemy_gpio_set_value(1, 1); /* set EXT_IO3 ON */
+
+ udelay(1);
+ return 1;
+}
+
+static const char mtx1_irqtab[][5] = {
+ [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
+ [1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
+ [2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
+ [3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
+ [4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
+ [5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
+ [6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
+ [7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
+};
+
+static int mtx1_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ return mtx1_irqtab[slot][pin];
+}
+
+static struct alchemy_pci_platdata mtx1_pci_pd = {
+ .board_map_irq = mtx1_map_pci_irq,
+ .board_pci_idsel = mtx1_pci_idsel,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device mtx1_pci_host = {
+ .dev.platform_data = &mtx1_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static struct __initdata platform_device * mtx1_devs[] = {
+ &mtx1_pci_host,
+ &mtx1_gpio_leds,
+ &mtx1_wdt,
+ &mtx1_button,
+ &mtx1_mtd,
+};
+
+static struct au1000_eth_platform_data mtx1_au1000_eth0_pdata = {
+ .phy_search_highest_addr = 1,
+ .phy1_search_mac0 = 1,
+};
+
+static int __init mtx1_register_devices(void)
+{
+ int rc;
+
+ irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
+ irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+
+ au1xxx_override_eth_cfg(0, &mtx1_au1000_eth0_pdata);
+
+ rc = gpio_request(mtx1_gpio_button[0].gpio,
+ mtx1_gpio_button[0].desc);
+ if (rc < 0) {
+ printk(KERN_INFO "mtx1: failed to request %d\n",
+ mtx1_gpio_button[0].gpio);
+ goto out;
+ }
+ gpio_direction_input(mtx1_gpio_button[0].gpio);
+out:
+ return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
+}
+arch_initcall(mtx1_register_devices);
diff --git a/arch/mips/alchemy/board-xxs1500.c b/arch/mips/alchemy/board-xxs1500.c
new file mode 100644
index 0000000..bd55136
--- /dev/null
+++ b/arch/mips/alchemy/board-xxs1500.c
@@ -0,0 +1,154 @@
+/*
+ * BRIEF MODULE DESCRIPTION
+ * MyCable XXS1500 board support
+ *
+ * Copyright 2003, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+ return "XXS1500";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str || strict_strtoul(memsize_str, 0, &memsize))
+ memsize = 0x04000000;
+
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void xxs1500_reset(char *c)
+{
+ /* Jump to the reset vector */
+ __asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void xxs1500_power_off(void)
+{
+ while (1)
+ asm volatile (
+ " .set mips32 \n"
+ " wait \n"
+ " .set mips0 \n");
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+
+ pm_power_off = xxs1500_power_off;
+ _machine_halt = xxs1500_power_off;
+ _machine_restart = xxs1500_reset;
+
+ alchemy_gpio1_input_enable();
+ alchemy_gpio2_enable();
+
+ /* Set multiple use pins (UART3/GPIO) to UART (it's used as UART too) */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+ pin_func |= SYS_PF_UR3;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ /* Enable UART */
+ alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+ /* Enable DTR (MCR bit 0) = USB power up */
+ __raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
+ wmb();
+}
+
+/******************************************************************************/
+
+static struct resource xxs1500_pcmcia_res[] = {
+ {
+ .name = "pcmcia-io",
+ .flags = IORESOURCE_MEM,
+ .start = AU1000_PCMCIA_IO_PHYS_ADDR,
+ .end = AU1000_PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
+ },
+ {
+ .name = "pcmcia-attr",
+ .flags = IORESOURCE_MEM,
+ .start = AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ .end = AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ },
+ {
+ .name = "pcmcia-mem",
+ .flags = IORESOURCE_MEM,
+ .start = AU1000_PCMCIA_MEM_PHYS_ADDR,
+ .end = AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ },
+};
+
+static struct platform_device xxs1500_pcmcia_dev = {
+ .name = "xxs1500_pcmcia",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(xxs1500_pcmcia_res),
+ .resource = xxs1500_pcmcia_res,
+};
+
+static struct platform_device *xxs1500_devs[] __initdata = {
+ &xxs1500_pcmcia_dev,
+};
+
+static int __init xxs1500_dev_init(void)
+{
+ irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
+ irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO207_INT, IRQ_TYPE_LEVEL_LOW);
+
+ irq_set_irq_type(AU1500_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO2_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(AU1500_GPIO4_INT, IRQ_TYPE_LEVEL_LOW); /* CF irq */
+ irq_set_irq_type(AU1500_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);
+
+ return platform_add_devices(xxs1500_devs,
+ ARRAY_SIZE(xxs1500_devs));
+}
+device_initcall(xxs1500_dev_init);
diff --git a/arch/mips/alchemy/gpr/Makefile b/arch/mips/alchemy/gpr/Makefile
deleted file mode 100644
index cb73fe2..0000000
--- a/arch/mips/alchemy/gpr/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2003 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for Trapeze ITS GPR board.
-#
-
-obj-y += board_setup.o init.o platform.o
diff --git a/arch/mips/alchemy/gpr/board_setup.c b/arch/mips/alchemy/gpr/board_setup.c
deleted file mode 100644
index dea45c7..0000000
--- a/arch/mips/alchemy/gpr/board_setup.c
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * Copyright 2010 Wolfgang Grandegger <wg@denx.de>
- *
- * Copyright 2000-2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/pm.h>
-
-#include <asm/reboot.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#include <prom.h>
-
-static void gpr_reset(char *c)
-{
- /* switch System-LED to orange (red# and green# on) */
- alchemy_gpio_direction_output(4, 0);
- alchemy_gpio_direction_output(5, 0);
-
- /* trigger watchdog to reset board in 200ms */
- printk(KERN_EMERG "Triggering watchdog soft reset...\n");
- raw_local_irq_disable();
- alchemy_gpio_direction_output(1, 0);
- udelay(1);
- alchemy_gpio_set_value(1, 1);
- while (1)
- cpu_wait();
-}
-
-static void gpr_power_off(void)
-{
- while (1)
- cpu_wait();
-}
-
-void __init board_setup(void)
-{
- printk(KERN_INFO "Trapeze ITS GPR board\n");
-
- pm_power_off = gpr_power_off;
- _machine_halt = gpr_power_off;
- _machine_restart = gpr_reset;
-
- /* Enable UART1/3 */
- alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
- alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
-
- /* Take away Reset of UMTS-card */
- alchemy_gpio_direction_output(215, 1);
-}
diff --git a/arch/mips/alchemy/gpr/init.c b/arch/mips/alchemy/gpr/init.c
deleted file mode 100644
index 229aafa..0000000
--- a/arch/mips/alchemy/gpr/init.c
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * Copyright 2010 Wolfgang Grandegger <wg@denx.de>
- *
- * Copyright 2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "GPR";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtoul(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void prom_putchar(unsigned char c)
-{
- alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
-}
diff --git a/arch/mips/alchemy/gpr/platform.c b/arch/mips/alchemy/gpr/platform.c
deleted file mode 100644
index 982ce85..0000000
--- a/arch/mips/alchemy/gpr/platform.c
+++ /dev/null
@@ -1,230 +0,0 @@
-/*
- * GPR board platform device registration
- *
- * Copyright (C) 2010 Wolfgang Grandegger <wg@denx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-/*
- * Watchdog
- */
-static struct resource gpr_wdt_resource[] = {
- [0] = {
- .start = 1,
- .end = 1,
- .name = "gpr-adm6320-wdt",
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device gpr_wdt_device = {
- .name = "adm6320-wdt",
- .id = 0,
- .num_resources = ARRAY_SIZE(gpr_wdt_resource),
- .resource = gpr_wdt_resource,
-};
-
-/*
- * FLASH
- *
- * 0x00000000-0x00200000 : "kernel"
- * 0x00200000-0x00a00000 : "rootfs"
- * 0x01d00000-0x01f00000 : "config"
- * 0x01c00000-0x01d00000 : "yamon"
- * 0x01d00000-0x01d40000 : "yamon env vars"
- * 0x00000000-0x00a00000 : "kernel+rootfs"
- */
-static struct mtd_partition gpr_mtd_partitions[] = {
- {
- .name = "kernel",
- .size = 0x00200000,
- .offset = 0,
- },
- {
- .name = "rootfs",
- .size = 0x00800000,
- .offset = MTDPART_OFS_APPEND,
- .mask_flags = MTD_WRITEABLE,
- },
- {
- .name = "config",
- .size = 0x00200000,
- .offset = 0x01d00000,
- },
- {
- .name = "yamon",
- .size = 0x00100000,
- .offset = 0x01c00000,
- },
- {
- .name = "yamon env vars",
- .size = 0x00040000,
- .offset = MTDPART_OFS_APPEND,
- },
- {
- .name = "kernel+rootfs",
- .size = 0x00a00000,
- .offset = 0,
- },
-};
-
-static struct physmap_flash_data gpr_flash_data = {
- .width = 4,
- .nr_parts = ARRAY_SIZE(gpr_mtd_partitions),
- .parts = gpr_mtd_partitions,
-};
-
-static struct resource gpr_mtd_resource = {
- .start = 0x1e000000,
- .end = 0x1fffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device gpr_mtd_device = {
- .name = "physmap-flash",
- .dev = {
- .platform_data = &gpr_flash_data,
- },
- .num_resources = 1,
- .resource = &gpr_mtd_resource,
-};
-
-/*
- * LEDs
- */
-static struct gpio_led gpr_gpio_leds[] = {
- { /* green */
- .name = "gpr:green",
- .gpio = 4,
- .active_low = 1,
- },
- { /* red */
- .name = "gpr:red",
- .gpio = 5,
- .active_low = 1,
- }
-};
-
-static struct gpio_led_platform_data gpr_led_data = {
- .num_leds = ARRAY_SIZE(gpr_gpio_leds),
- .leds = gpr_gpio_leds,
-};
-
-static struct platform_device gpr_led_devices = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpr_led_data,
- }
-};
-
-/*
- * I2C
- */
-static struct i2c_gpio_platform_data gpr_i2c_data = {
- .sda_pin = 209,
- .sda_is_open_drain = 1,
- .scl_pin = 210,
- .scl_is_open_drain = 1,
- .udelay = 2, /* ~100 kHz */
- .timeout = HZ,
- };
-
-static struct platform_device gpr_i2c_device = {
- .name = "i2c-gpio",
- .id = -1,
- .dev.platform_data = &gpr_i2c_data,
-};
-
-static struct i2c_board_info gpr_i2c_info[] __initdata = {
- {
- I2C_BOARD_INFO("lm83", 0x18),
- .type = "lm83"
- }
-};
-
-
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static int gpr_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot == 0) && (pin == 1))
- return AU1550_PCI_INTA;
- else if ((slot == 0) && (pin == 2))
- return AU1550_PCI_INTB;
-
- return -1;
-}
-
-static struct alchemy_pci_platdata gpr_pci_pd = {
- .board_map_irq = gpr_map_pci_irq,
- .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
- PCI_CONFIG_CH |
-#if defined(__MIPSEB__)
- PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
-#else
- 0,
-#endif
-};
-
-static struct platform_device gpr_pci_host_dev = {
- .dev.platform_data = &gpr_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static struct platform_device *gpr_devices[] __initdata = {
- &gpr_wdt_device,
- &gpr_mtd_device,
- &gpr_i2c_device,
- &gpr_led_devices,
-};
-
-static int __init gpr_pci_init(void)
-{
- return platform_device_register(&gpr_pci_host_dev);
-}
-/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
-arch_initcall(gpr_pci_init);
-
-
-static int __init gpr_dev_init(void)
-{
- i2c_register_board_info(0, gpr_i2c_info, ARRAY_SIZE(gpr_i2c_info));
-
- return platform_add_devices(gpr_devices, ARRAY_SIZE(gpr_devices));
-}
-device_initcall(gpr_dev_init);
diff --git a/arch/mips/alchemy/mtx-1/Makefile b/arch/mips/alchemy/mtx-1/Makefile
deleted file mode 100644
index 81b540c..0000000
--- a/arch/mips/alchemy/mtx-1/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# Copyright 2003 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-# Bruno Randolf <bruno.randolf@4g-systems.biz>
-#
-# Makefile for 4G Systems MTX-1 board.
-#
-
-obj-y += init.o board_setup.o platform.o
diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
deleted file mode 100644
index 851a5ab..0000000
--- a/arch/mips/alchemy/mtx-1/board_setup.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * 4G Systems MTX-1 board setup.
- *
- * Copyright 2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- * Bruno Randolf <bruno.randolf@4g-systems.biz>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-
-#include <asm/reboot.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#include <prom.h>
-
-static void mtx1_reset(char *c)
-{
- /* Jump to the reset vector */
- __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-}
-
-static void mtx1_power_off(void)
-{
- while (1)
- asm volatile (
- " .set mips32 \n"
- " wait \n"
- " .set mips0 \n");
-}
-
-void __init board_setup(void)
-{
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- /* Enable USB power switch */
- alchemy_gpio_direction_output(204, 0);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Initialize sys_pinfunc */
- au_writel(SYS_PF_NI2, SYS_PINFUNC);
-
- /* Initialize GPIO */
- au_writel(~0, KSEG1ADDR(AU1000_SYS_PHYS_ADDR) + SYS_TRIOUTCLR);
- alchemy_gpio_direction_output(0, 0); /* Disable M66EN (PCI 66MHz) */
- alchemy_gpio_direction_output(3, 1); /* Disable PCI CLKRUN# */
- alchemy_gpio_direction_output(1, 1); /* Enable EXT_IO3 */
- alchemy_gpio_direction_output(5, 0); /* Disable eth PHY TX_ER */
-
- /* Enable LED and set it to green */
- alchemy_gpio_direction_output(211, 1); /* green on */
- alchemy_gpio_direction_output(212, 0); /* red off */
-
- pm_power_off = mtx1_power_off;
- _machine_halt = mtx1_power_off;
- _machine_restart = mtx1_reset;
-
- printk(KERN_INFO "4G Systems MTX-1 Board\n");
-}
-
-static int __init mtx1_init_irq(void)
-{
- irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
- irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
-
- return 0;
-}
-arch_initcall(mtx1_init_irq);
diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
deleted file mode 100644
index 2e81cc7..0000000
--- a/arch/mips/alchemy/mtx-1/init.c
+++ /dev/null
@@ -1,66 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * 4G Systems MTX-1 board setup
- *
- * Copyright 2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- * Bruno Randolf <bruno.randolf@4g-systems.biz>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "MTX-1";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtoul(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void prom_putchar(unsigned char c)
-{
- alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
-}
diff --git a/arch/mips/alchemy/mtx-1/platform.c b/arch/mips/alchemy/mtx-1/platform.c
deleted file mode 100644
index cc47b68..0000000
--- a/arch/mips/alchemy/mtx-1/platform.c
+++ /dev/null
@@ -1,230 +0,0 @@
-/*
- * MTX-1 platform devices registration
- *
- * Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <mtd/mtd-abi.h>
-
-#include <asm/mach-au1x00/au1xxx_eth.h>
-
-static struct gpio_keys_button mtx1_gpio_button[] = {
- {
- .gpio = 207,
- .code = BTN_0,
- .desc = "System button",
- }
-};
-
-static struct gpio_keys_platform_data mtx1_buttons_data = {
- .buttons = mtx1_gpio_button,
- .nbuttons = ARRAY_SIZE(mtx1_gpio_button),
-};
-
-static struct platform_device mtx1_button = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &mtx1_buttons_data,
- }
-};
-
-static struct resource mtx1_wdt_res[] = {
- [0] = {
- .start = 215,
- .end = 215,
- .name = "mtx1-wdt-gpio",
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device mtx1_wdt = {
- .name = "mtx1-wdt",
- .id = 0,
- .num_resources = ARRAY_SIZE(mtx1_wdt_res),
- .resource = mtx1_wdt_res,
-};
-
-static struct gpio_led default_leds[] = {
- {
- .name = "mtx1:green",
- .gpio = 211,
- }, {
- .name = "mtx1:red",
- .gpio = 212,
- },
-};
-
-static struct gpio_led_platform_data mtx1_led_data = {
- .num_leds = ARRAY_SIZE(default_leds),
- .leds = default_leds,
-};
-
-static struct platform_device mtx1_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &mtx1_led_data,
- }
-};
-
-static struct mtd_partition mtx1_mtd_partitions[] = {
- {
- .name = "filesystem",
- .size = 0x01C00000,
- .offset = 0,
- },
- {
- .name = "yamon",
- .size = 0x00100000,
- .offset = MTDPART_OFS_APPEND,
- .mask_flags = MTD_WRITEABLE,
- },
- {
- .name = "kernel",
- .size = 0x002c0000,
- .offset = MTDPART_OFS_APPEND,
- },
- {
- .name = "yamon env",
- .size = 0x00040000,
- .offset = MTDPART_OFS_APPEND,
- },
-};
-
-static struct physmap_flash_data mtx1_flash_data = {
- .width = 4,
- .nr_parts = 4,
- .parts = mtx1_mtd_partitions,
-};
-
-static struct resource mtx1_mtd_resource = {
- .start = 0x1e000000,
- .end = 0x1fffffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device mtx1_mtd = {
- .name = "physmap-flash",
- .dev = {
- .platform_data = &mtx1_flash_data,
- },
- .num_resources = 1,
- .resource = &mtx1_mtd_resource,
-};
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static int mtx1_pci_idsel(unsigned int devsel, int assert)
-{
- /* This function is only necessary to support a proprietary Cardbus
- * adapter on the mtx-1 "singleboard" variant. It triggers a custom
- * logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
- */
- if (assert && devsel != 0)
- /* Suppress signal to Cardbus */
- alchemy_gpio_set_value(1, 0); /* set EXT_IO3 OFF */
- else
- alchemy_gpio_set_value(1, 1); /* set EXT_IO3 ON */
-
- udelay(1);
- return 1;
-}
-
-static const char mtx1_irqtab[][5] = {
- [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
- [1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
- [2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
- [3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
- [4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
- [5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
- [6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
- [7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
-};
-
-static int mtx1_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- return mtx1_irqtab[slot][pin];
-}
-
-static struct alchemy_pci_platdata mtx1_pci_pd = {
- .board_map_irq = mtx1_map_pci_irq,
- .board_pci_idsel = mtx1_pci_idsel,
- .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
- PCI_CONFIG_CH |
-#if defined(__MIPSEB__)
- PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
-#else
- 0,
-#endif
-};
-
-static struct platform_device mtx1_pci_host = {
- .dev.platform_data = &mtx1_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-
-static struct __initdata platform_device * mtx1_devs[] = {
- &mtx1_pci_host,
- &mtx1_gpio_leds,
- &mtx1_wdt,
- &mtx1_button,
- &mtx1_mtd,
-};
-
-static struct au1000_eth_platform_data mtx1_au1000_eth0_pdata = {
- .phy_search_highest_addr = 1,
- .phy1_search_mac0 = 1,
-};
-
-static int __init mtx1_register_devices(void)
-{
- int rc;
-
- au1xxx_override_eth_cfg(0, &mtx1_au1000_eth0_pdata);
-
- rc = gpio_request(mtx1_gpio_button[0].gpio,
- mtx1_gpio_button[0].desc);
- if (rc < 0) {
- printk(KERN_INFO "mtx1: failed to request %d\n",
- mtx1_gpio_button[0].gpio);
- goto out;
- }
- gpio_direction_input(mtx1_gpio_button[0].gpio);
-out:
- return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
-}
-
-arch_initcall(mtx1_register_devices);
diff --git a/arch/mips/alchemy/xxs1500/Makefile b/arch/mips/alchemy/xxs1500/Makefile
deleted file mode 100644
index 91defcf..0000000
--- a/arch/mips/alchemy/xxs1500/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2003 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for MyCable XXS1500 board.
-#
-
-obj-y += init.o board_setup.o platform.o
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
deleted file mode 100644
index 3fa83f7..0000000
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * Copyright 2000-2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/pm.h>
-
-#include <asm/reboot.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#include <prom.h>
-
-static void xxs1500_reset(char *c)
-{
- /* Jump to the reset vector */
- __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-}
-
-static void xxs1500_power_off(void)
-{
- while (1)
- asm volatile (
- " .set mips32 \n"
- " wait \n"
- " .set mips0 \n");
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
-
- pm_power_off = xxs1500_power_off;
- _machine_halt = xxs1500_power_off;
- _machine_restart = xxs1500_reset;
-
- alchemy_gpio1_input_enable();
- alchemy_gpio2_enable();
-
- /* Set multiple use pins (UART3/GPIO) to UART (it's used as UART too) */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
- pin_func |= SYS_PF_UR3;
- au_writel(pin_func, SYS_PINFUNC);
-
- /* Enable UART */
- alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
- /* Enable DTR (MCR bit 0) = USB power up */
- __raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
- wmb();
-}
-
-static int __init xxs1500_init_irq(void)
-{
- irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
- irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO207_INT, IRQF_TRIGGER_LOW);
-
- irq_set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* CF irq */
- irq_set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW);
-
- return 0;
-}
-arch_initcall(xxs1500_init_irq);
diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
deleted file mode 100644
index 0ee02cf..0000000
--- a/arch/mips/alchemy/xxs1500/init.c
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * XXS1500 board setup
- *
- * Copyright 2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "XXS1500";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str || strict_strtoul(memsize_str, 0, &memsize))
- memsize = 0x04000000;
-
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void prom_putchar(unsigned char c)
-{
- alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
-}
diff --git a/arch/mips/alchemy/xxs1500/platform.c b/arch/mips/alchemy/xxs1500/platform.c
deleted file mode 100644
index 06a3a45..0000000
--- a/arch/mips/alchemy/xxs1500/platform.c
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * XXS1500 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-static struct resource xxs1500_pcmcia_res[] = {
- {
- .name = "pcmcia-io",
- .flags = IORESOURCE_MEM,
- .start = AU1000_PCMCIA_IO_PHYS_ADDR,
- .end = AU1000_PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
- },
- {
- .name = "pcmcia-attr",
- .flags = IORESOURCE_MEM,
- .start = AU1000_PCMCIA_ATTR_PHYS_ADDR,
- .end = AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- },
- {
- .name = "pcmcia-mem",
- .flags = IORESOURCE_MEM,
- .start = AU1000_PCMCIA_MEM_PHYS_ADDR,
- .end = AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- },
-};
-
-static struct platform_device xxs1500_pcmcia_dev = {
- .name = "xxs1500_pcmcia",
- .id = -1,
- .num_resources = ARRAY_SIZE(xxs1500_pcmcia_res),
- .resource = xxs1500_pcmcia_res,
-};
-
-static struct platform_device *xxs1500_devs[] __initdata = {
- &xxs1500_pcmcia_dev,
-};
-
-static int __init xxs1500_dev_init(void)
-{
- return platform_add_devices(xxs1500_devs,
- ARRAY_SIZE(xxs1500_devs));
-}
-device_initcall(xxs1500_dev_init);
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 08/18] MIPS: Alchemy: merge devboard code into single per-board files.
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (6 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 07/18] MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-04 8:35 ` [PATCH v2 " Manuel Lauss
2011-11-01 19:03 ` Manuel Lauss
` (9 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/devboards/Makefile | 16 +-
arch/mips/alchemy/devboards/db1200.c | 705 ++++++++++++++++++++++
arch/mips/alchemy/devboards/db1200/Makefile | 1 -
arch/mips/alchemy/devboards/db1200/platform.c | 648 --------------------
arch/mips/alchemy/devboards/db1200/setup.c | 81 ---
arch/mips/alchemy/devboards/db1x00.c | 256 ++++++++
arch/mips/alchemy/devboards/db1x00/Makefile | 8 -
arch/mips/alchemy/devboards/db1x00/board_setup.c | 108 ----
arch/mips/alchemy/devboards/db1x00/platform.c | 206 -------
arch/mips/alchemy/devboards/pb1100.c | 167 +++++
arch/mips/alchemy/devboards/pb1100/Makefile | 8 -
arch/mips/alchemy/devboards/pb1100/board_setup.c | 127 ----
arch/mips/alchemy/devboards/pb1100/platform.c | 77 ---
arch/mips/alchemy/devboards/pb1200.c | 464 ++++++++++++++
arch/mips/alchemy/devboards/pb1200/Makefile | 5 -
arch/mips/alchemy/devboards/pb1200/board_setup.c | 174 ------
arch/mips/alchemy/devboards/pb1200/platform.c | 339 -----------
arch/mips/alchemy/devboards/pb1500.c | 198 ++++++
arch/mips/alchemy/devboards/pb1500/Makefile | 8 -
arch/mips/alchemy/devboards/pb1500/board_setup.c | 139 -----
arch/mips/alchemy/devboards/pb1500/platform.c | 94 ---
arch/mips/alchemy/devboards/pb1550.c | 178 ++++++
arch/mips/alchemy/devboards/pb1550/Makefile | 8 -
arch/mips/alchemy/devboards/pb1550/board_setup.c | 80 ---
arch/mips/alchemy/devboards/pb1550/platform.c | 140 -----
25 files changed, 1976 insertions(+), 2259 deletions(-)
create mode 100644 arch/mips/alchemy/devboards/db1200.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1200/platform.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/setup.c
create mode 100644 arch/mips/alchemy/devboards/db1x00.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1x00/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1100.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1100/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1200.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1200/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1500.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1500/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1550.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1550/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/platform.c
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 3467ec9..f562852 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -4,13 +4,13 @@
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_MIPS_PB1100) += pb1100/
-obj-$(CONFIG_MIPS_PB1200) += pb1200/
-obj-$(CONFIG_MIPS_PB1500) += pb1500/
-obj-$(CONFIG_MIPS_PB1550) += pb1550/
-obj-$(CONFIG_MIPS_DB1000) += db1x00/
-obj-$(CONFIG_MIPS_DB1100) += db1x00/
-obj-$(CONFIG_MIPS_DB1200) += db1200/
+obj-$(CONFIG_MIPS_PB1100) += pb1100.o
+obj-$(CONFIG_MIPS_PB1200) += pb1200.o
+obj-$(CONFIG_MIPS_PB1500) += pb1500.o
+obj-$(CONFIG_MIPS_PB1550) += pb1550.o
+obj-$(CONFIG_MIPS_DB1000) += db1x00.o
+obj-$(CONFIG_MIPS_DB1100) += db1x00.o
+obj-$(CONFIG_MIPS_DB1200) += db1200.o
obj-$(CONFIG_MIPS_DB1300) += db1300.o
-obj-$(CONFIG_MIPS_DB1500) += db1x00/
+obj-$(CONFIG_MIPS_DB1500) += db1x00.o
obj-$(CONFIG_MIPS_DB1550) += db1550.o
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
new file mode 100644
index 0000000..43f5f1b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -0,0 +1,705 @@
+/*
+ * DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008-2011 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/smc91x.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "DB1200";
+}
+
+void __init board_setup(void)
+{
+ unsigned long freq0, clksrc, div, pfc;
+ unsigned short whoami;
+
+ bcsr_init(DB1200_BCSR_PHYS_ADDR,
+ DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
+ " Board-ID %d Daughtercard ID %d\n",
+ (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+ /* SMBus/SPI on PSC0, Audio on PSC1 */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
+ pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
+ pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
+ * CPU clock; all other clock generators off/unused.
+ */
+ div = (get_au1x00_speed() + 25000000) / 50000000;
+ if (div & 1)
+ div++;
+ div = ((div >> 1) - 1) & 0xff;
+
+ freq0 = div << SYS_FC_FRDIV0_BIT;
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+ freq0 |= SYS_FC_FE0; /* enable F0 */
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+
+ /* psc0_intclk comes 1:1 from F0 */
+ clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
+ __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
+ wmb();
+}
+
+/******************************************************************************/
+
+static struct mtd_partition db1200_spiflash_parts[] = {
+ {
+ .name = "DB1200 SPI flash",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct flash_platform_data db1200_spiflash_data = {
+ .name = "s25fl001",
+ .parts = db1200_spiflash_parts,
+ .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
+ .type = "m25p10",
+};
+
+static struct spi_board_info db1200_spi_devs[] __initdata = {
+ {
+ /* TI TMP121AIDBVR temp sensor */
+ .modalias = "tmp121",
+ .max_speed_hz = 2000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = 0,
+ },
+ {
+ /* Spansion S25FL001D0FMA SPI flash */
+ .modalias = "m25p80",
+ .max_speed_hz = 50000000,
+ .bus_num = 0,
+ .chip_select = 1,
+ .mode = 0,
+ .platform_data = &db1200_spiflash_data,
+ },
+};
+
+static struct i2c_board_info db1200_i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("24c04", 0x52), }, /* AT24C04-10 I2C eeprom */
+ { I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
+ { I2C_BOARD_INFO("wm8731", 0x1b), }, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1200_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1200_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1200_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
+ .partitions = db1200_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1200_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1200_nand_device_ready,
+ .cmd_ctrl = au1200_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1200_nand_res[] = {
+ [0] = {
+ .start = DB1200_NAND_PHYS_ADDR,
+ .end = DB1200_NAND_PHYS_ADDR + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1200_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1200_nand_res),
+ .resource = db1200_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1200_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct smc91x_platdata db1200_eth_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource db1200_eth_res[] = {
+ [0] = {
+ .start = DB1200_ETH_PHYS_ADDR,
+ .end = DB1200_ETH_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_ETH_INT,
+ .end = DB1200_ETH_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1200_eth_dev = {
+ .dev = {
+ .platform_data = &db1200_eth_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(db1200_eth_res),
+ .resource = db1200_eth_res,
+};
+
+/**********************************************************************/
+
+static struct resource db1200_ide_res[] = {
+ [0] = {
+ .start = DB1200_IDE_PHYS_ADDR,
+ .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_IDE_INT,
+ .end = DB1200_IDE_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_DMA_REQ1,
+ .end = AU1200_DSCR_CMD0_DMA_REQ1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_ide_dev = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_ide_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(db1200_ide_res),
+ .resource = db1200_ide_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1200_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+/* SD carddetects: they're supposed to be edge-triggered, but ack
+ * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
+ * is disabled and its counterpart enabled. The 500ms timeout is
+ * because the carddetect isn't debounced in hardware.
+ */
+static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ if (irq == DB1200_SD0_INSERT_INT) {
+ disable_irq_nosync(DB1200_SD0_INSERT_INT);
+ enable_irq(DB1200_SD0_EJECT_INT);
+ } else {
+ disable_irq_nosync(DB1200_SD0_EJECT_INT);
+ enable_irq(DB1200_SD0_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m */
+ mmc_cd = symbol_get(mmc_detect_change);
+ if (mmc_cd) {
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int db1200_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_eject", mmc_host);
+ if (ret) {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
+ enable_irq(DB1200_SD0_EJECT_INT);
+ else
+ enable_irq(DB1200_SD0_INSERT_INT);
+
+ } else {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ free_irq(DB1200_SD0_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void db1200_mmc_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static int db1200_mmc_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int db1200_mmc_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void db1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1200_mmc_led = {
+ .brightness_set = db1200_mmcled_set,
+};
+
+static struct au1xmmc_platform_data db1200mmc_platdata = {
+ .cd_setup = db1200_mmc_cd_setup,
+ .set_power = db1200_mmc_set_power,
+ .card_inserted = db1200_mmc_card_inserted,
+ .card_readonly = db1200_mmc_card_readonly,
+ .led = &db1200_mmc_led,
+};
+
+static struct resource au1200_mmc0_resources[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX0,
+ .end = AU1200_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX0,
+ .end = AU1200_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200mmc_platdata,
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc0_resources),
+ .resource = au1200_mmc0_resources,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_LCD_INT,
+ .end = AU1200_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1200_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1200_lcd_res),
+ .resource = au1200_lcd_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC0_TX,
+ .end = AU1200_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC0_RX,
+ .end = AU1200_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+ if (cs)
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
+ else
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1200_spi_platdata = {
+ .mainclk_hz = 50000000, /* PSC0 clock */
+ .num_chipselect = 2,
+ .activate_cs = db1200_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_spi_dev = {
+ .dev = {
+ .dma_mask = &spi_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200_spi_platdata,
+ },
+ .name = "au1550-spi",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_psc1_res[] = {
+ [0] = {
+ .start = AU1550_PSC1_PHYS_ADDR,
+ .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC1_INT,
+ .end = AU1200_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC1_TX,
+ .end = AU1200_DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC1_RX,
+ .end = AU1200_DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+/* AC97 or I2S device */
+static struct platform_device db1200_audio_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1200_psc1_res),
+ .resource = au1200_psc1_res,
+};
+
+/* DB1200 ASoC card device */
+static struct platform_device db1200_sound_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device db1200_stac_dev = {
+ .name = "ac97-codec",
+ .id = 1, /* on PSC1 */
+};
+
+static struct platform_device db1200_audiodma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device *db1200_devs[] __initdata = {
+ NULL, /* PSC0, selected by S6.8 */
+ &db1200_ide_dev,
+ &db1200_mmc0_dev,
+ &au1200_lcd_dev,
+ &db1200_eth_dev,
+ &db1200_rtc_dev,
+ &db1200_nand_dev,
+ &db1200_audiodma_dev,
+ &db1200_audio_dev,
+ &db1200_stac_dev,
+ &db1200_sound_dev,
+};
+
+static int __init db1200_dev_init(void)
+{
+ unsigned long pfc;
+ unsigned short sw;
+ int swapped;
+
+ /* GPIO7 is low-level triggered CPLD cascade */
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
+
+ /* insert/eject pairs: one of both is always screaming. To avoid
+ * issues they must not be automatically enabled when initially
+ * requested.
+ */
+ irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
+
+ i2c_register_board_info(0, db1200_i2c_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+ spi_register_board_info(db1200_spi_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+
+ /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
+ * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+ */
+
+ /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
+ * this pin is claimed by PSC0 (unused though, but pinmux doesn't
+ * allow to free it without crippling the SPI interface).
+ * As a result, in SPI mode, OTG simply won't work (PSC0 uses
+ * it as an input pin which is pulled high on the boards).
+ */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
+
+ /* switch off OTG VBUS supply */
+ gpio_request(215, "otg-vbus");
+ gpio_direction_output(215, 1);
+
+ printk(KERN_INFO "DB1200 device configuration:\n");
+
+ sw = bcsr_read(BCSR_SWITCHES);
+ if (sw & BCSR_SWITCHES_DIP_8) {
+ db1200_devs[0] = &db1200_i2c_dev;
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
+ printk(KERN_INFO " OTG port VBUS supply available!\n");
+ } else {
+ db1200_devs[0] = &db1200_spi_dev;
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
+
+ pfc |= (1 << 17); /* PSC0 owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
+ printk(KERN_INFO " OTG port VBUS supply disabled\n");
+ }
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+ * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+ */
+ sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+ if (sw == BCSR_SWITCHES_DIP_8) {
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+ db1200_audio_dev.name = "au1xpsc_i2s";
+ db1200_sound_dev.name = "db1200-i2s";
+ printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+ } else {
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+ db1200_audio_dev.name = "au1xpsc_ac97";
+ db1200_sound_dev.name = "db1200-ac97";
+ printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+ }
+
+ /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
+ /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
+ /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(64 << 20, 2, swapped);
+
+ return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+}
+device_initcall(db1200_dev_init);
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1200/Makefile b/arch/mips/alchemy/devboards/db1200/Makefile
deleted file mode 100644
index 17840a5..0000000
--- a/arch/mips/alchemy/devboards/db1200/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-y += setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1200/platform.c b/arch/mips/alchemy/devboards/db1200/platform.c
deleted file mode 100644
index c61867c..0000000
--- a/arch/mips/alchemy/devboards/db1200/platform.c
+++ /dev/null
@@ -1,648 +0,0 @@
-/*
- * DBAu1200 board platform device registration
- *
- * Copyright (C) 2008-2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/mmc/host.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-au1x00/au1550_spi.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-#include "../platform.h"
-
-static struct mtd_partition db1200_spiflash_parts[] = {
- {
- .name = "DB1200 SPI flash",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct flash_platform_data db1200_spiflash_data = {
- .name = "s25fl001",
- .parts = db1200_spiflash_parts,
- .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
- .type = "m25p10",
-};
-
-static struct spi_board_info db1200_spi_devs[] __initdata = {
- {
- /* TI TMP121AIDBVR temp sensor */
- .modalias = "tmp121",
- .max_speed_hz = 2000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = 0,
- },
- {
- /* Spansion S25FL001D0FMA SPI flash */
- .modalias = "m25p80",
- .max_speed_hz = 50000000,
- .bus_num = 0,
- .chip_select = 1,
- .mode = 0,
- .platform_data = &db1200_spiflash_data,
- },
-};
-
-static struct i2c_board_info db1200_i2c_devs[] __initdata = {
- {
- /* AT24C04-10 I2C eeprom */
- I2C_BOARD_INFO("24c04", 0x52),
- },
- {
- /* Philips NE1619 temp/voltage sensor (adm1025 drv) */
- I2C_BOARD_INFO("ne1619", 0x2d),
- },
- {
- /* I2S audio codec WM8731 */
- I2C_BOARD_INFO("wm8731", 0x1b),
- },
-};
-
-/**********************************************************************/
-
-static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
- unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
-
- ioaddr &= 0xffffff00;
-
- if (ctrl & NAND_CLE) {
- ioaddr += MEM_STNAND_CMD;
- } else if (ctrl & NAND_ALE) {
- ioaddr += MEM_STNAND_ADDR;
- } else {
- /* assume we want to r/w real data by default */
- ioaddr += MEM_STNAND_DATA;
- }
- this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
- if (cmd != NAND_CMD_NONE) {
- __raw_writeb(cmd, this->IO_ADDR_W);
- wmb();
- }
-}
-
-static int au1200_nand_device_ready(struct mtd_info *mtd)
-{
- return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
-}
-
-static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
-
-static struct mtd_partition db1200_nand_parts[] = {
- {
- .name = "NAND FS 0",
- .offset = 0,
- .size = 8 * 1024 * 1024,
- },
- {
- .name = "NAND FS 1",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL
- },
-};
-
-struct platform_nand_data db1200_nand_platdata = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
- .partitions = db1200_nand_parts,
- .chip_delay = 20,
- .part_probe_types = db1200_part_probes,
- },
- .ctrl = {
- .dev_ready = au1200_nand_device_ready,
- .cmd_ctrl = au1200_nand_cmd_ctrl,
- },
-};
-
-static struct resource db1200_nand_res[] = {
- [0] = {
- .start = DB1200_NAND_PHYS_ADDR,
- .end = DB1200_NAND_PHYS_ADDR + 0xff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device db1200_nand_dev = {
- .name = "gen_nand",
- .num_resources = ARRAY_SIZE(db1200_nand_res),
- .resource = db1200_nand_res,
- .id = -1,
- .dev = {
- .platform_data = &db1200_nand_platdata,
- }
-};
-
-/**********************************************************************/
-
-static struct smc91x_platdata db1200_eth_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource db1200_eth_res[] = {
- [0] = {
- .start = DB1200_ETH_PHYS_ADDR,
- .end = DB1200_ETH_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DB1200_ETH_INT,
- .end = DB1200_ETH_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device db1200_eth_dev = {
- .dev = {
- .platform_data = &db1200_eth_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(db1200_eth_res),
- .resource = db1200_eth_res,
-};
-
-/**********************************************************************/
-
-static struct resource db1200_ide_res[] = {
- [0] = {
- .start = DB1200_IDE_PHYS_ADDR,
- .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DB1200_IDE_INT,
- .end = DB1200_IDE_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_ide_dev = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(db1200_ide_res),
- .resource = db1200_ide_res,
-};
-
-/**********************************************************************/
-
-static struct platform_device db1200_rtc_dev = {
- .name = "rtc-au1xxx",
- .id = -1,
-};
-
-/**********************************************************************/
-
-/* SD carddetects: they're supposed to be edge-triggered, but ack
- * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
- * is disabled and its counterpart enabled. The 500ms timeout is
- * because the carddetect isn't debounced in hardware.
- */
-static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
-{
- void(*mmc_cd)(struct mmc_host *, unsigned long);
-
- if (irq == DB1200_SD0_INSERT_INT) {
- disable_irq_nosync(DB1200_SD0_INSERT_INT);
- enable_irq(DB1200_SD0_EJECT_INT);
- } else {
- disable_irq_nosync(DB1200_SD0_EJECT_INT);
- enable_irq(DB1200_SD0_INSERT_INT);
- }
-
- /* link against CONFIG_MMC=m */
- mmc_cd = symbol_get(mmc_detect_change);
- if (mmc_cd) {
- mmc_cd(ptr, msecs_to_jiffies(500));
- symbol_put(mmc_detect_change);
- }
-
- return IRQ_HANDLED;
-}
-
-static int db1200_mmc_cd_setup(void *mmc_host, int en)
-{
- int ret;
-
- if (en) {
- ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
- IRQF_DISABLED, "sd_insert", mmc_host);
- if (ret)
- goto out;
-
- ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
- IRQF_DISABLED, "sd_eject", mmc_host);
- if (ret) {
- free_irq(DB1200_SD0_INSERT_INT, mmc_host);
- goto out;
- }
-
- if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
- enable_irq(DB1200_SD0_EJECT_INT);
- else
- enable_irq(DB1200_SD0_INSERT_INT);
-
- } else {
- free_irq(DB1200_SD0_INSERT_INT, mmc_host);
- free_irq(DB1200_SD0_EJECT_INT, mmc_host);
- }
- ret = 0;
-out:
- return ret;
-}
-
-static void db1200_mmc_set_power(void *mmc_host, int state)
-{
- if (state) {
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- msleep(400); /* stabilization time */
- } else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-}
-
-static int db1200_mmc_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int db1200_mmc_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void db1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- else
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
-}
-
-static struct led_classdev db1200_mmc_led = {
- .brightness_set = db1200_mmcled_set,
-};
-
-static struct au1xmmc_platform_data db1200mmc_platdata = {
- .cd_setup = db1200_mmc_cd_setup,
- .set_power = db1200_mmc_set_power,
- .card_inserted = db1200_mmc_card_inserted,
- .card_readonly = db1200_mmc_card_readonly,
- .led = &db1200_mmc_led,
-};
-
-static struct resource au1200_mmc0_resources[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200mmc_platdata,
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_resources),
- .resource = au1200_mmc0_resources,
-};
-
-/**********************************************************************/
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-/**********************************************************************/
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device db1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
-{
- if (cs)
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
- else
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
-}
-
-static struct au1550_spi_info db1200_spi_platdata = {
- .mainclk_hz = 50000000, /* PSC0 clock */
- .num_chipselect = 2,
- .activate_cs = db1200_spi_cs_en,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_spi_dev = {
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200_spi_platdata,
- },
- .name = "au1550-spi",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static struct resource au1200_psc1_res[] = {
- [0] = {
- .start = AU1550_PSC1_PHYS_ADDR,
- .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC1_INT,
- .end = AU1200_PSC1_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC1_TX,
- .end = AU1200_DSCR_CMD0_PSC1_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC1_RX,
- .end = AU1200_DSCR_CMD0_PSC1_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-/* AC97 or I2S device */
-static struct platform_device db1200_audio_dev = {
- /* name assigned later based on switch setting */
- .id = 1, /* PSC ID */
- .num_resources = ARRAY_SIZE(au1200_psc1_res),
- .resource = au1200_psc1_res,
-};
-
-/* DB1200 ASoC card device */
-static struct platform_device db1200_sound_dev = {
- /* name assigned later based on switch setting */
- .id = 1, /* PSC ID */
-};
-
-static struct platform_device db1200_stac_dev = {
- .name = "ac97-codec",
- .id = 1, /* on PSC1 */
-};
-
-static struct platform_device db1200_audiodma_dev = {
- .name = "au1xpsc-pcm",
- .id = 1, /* PSC ID */
-};
-
-static struct platform_device *db1200_devs[] __initdata = {
- NULL, /* PSC0, selected by S6.8 */
- &db1200_ide_dev,
- &db1200_mmc0_dev,
- &au1200_lcd_dev,
- &db1200_eth_dev,
- &db1200_rtc_dev,
- &db1200_nand_dev,
- &db1200_audiodma_dev,
- &db1200_audio_dev,
- &db1200_stac_dev,
- &db1200_sound_dev,
-};
-
-static int __init db1200_dev_init(void)
-{
- unsigned long pfc;
- unsigned short sw;
- int swapped;
-
- i2c_register_board_info(0, db1200_i2c_devs,
- ARRAY_SIZE(db1200_i2c_devs));
- spi_register_board_info(db1200_spi_devs,
- ARRAY_SIZE(db1200_i2c_devs));
-
- /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
- * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
- */
-
- /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
- * this pin is claimed by PSC0 (unused though, but pinmux doesn't
- * allow to free it without crippling the SPI interface).
- * As a result, in SPI mode, OTG simply won't work (PSC0 uses
- * it as an input pin which is pulled high on the boards).
- */
- pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
-
- /* switch off OTG VBUS supply */
- gpio_request(215, "otg-vbus");
- gpio_direction_output(215, 1);
-
- printk(KERN_INFO "DB1200 device configuration:\n");
-
- sw = bcsr_read(BCSR_SWITCHES);
- if (sw & BCSR_SWITCHES_DIP_8) {
- db1200_devs[0] = &db1200_i2c_dev;
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
-
- printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
- printk(KERN_INFO " OTG port VBUS supply available!\n");
- } else {
- db1200_devs[0] = &db1200_spi_dev;
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
-
- pfc |= (1 << 17); /* PSC0 owns GPIO215 */
-
- printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
- printk(KERN_INFO " OTG port VBUS supply disabled\n");
- }
- __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
- wmb();
-
- /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
- * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
- */
- sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
- if (sw == BCSR_SWITCHES_DIP_8) {
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
- db1200_audio_dev.name = "au1xpsc_i2s";
- db1200_sound_dev.name = "db1200-i2s";
- printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
- } else {
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
- db1200_audio_dev.name = "au1xpsc_ac97";
- db1200_sound_dev.name = "db1200-ac97";
- printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
- }
-
- /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
- __raw_writel(PSC_SEL_CLK_SERCLK,
- (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
- wmb();
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
- /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
- /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(64 << 20, 2, swapped);
-
- return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
-}
-device_initcall(db1200_dev_init);
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/db1200/setup.c b/arch/mips/alchemy/devboards/db1200/setup.c
deleted file mode 100644
index 4a89800..0000000
--- a/arch/mips/alchemy/devboards/db1200/setup.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * Alchemy/AMD/RMI DB1200 board setup.
- *
- * Licensed under the terms outlined in the file COPYING in the root of
- * this source archive.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1200";
-}
-
-void __init board_setup(void)
-{
- unsigned long freq0, clksrc, div, pfc;
- unsigned short whoami;
-
- bcsr_init(DB1200_BCSR_PHYS_ADDR,
- DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
-
- whoami = bcsr_read(BCSR_WHOAMI);
- printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
- " Board-ID %d Daughtercard ID %d\n",
- (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
-
- /* SMBus/SPI on PSC0, Audio on PSC1 */
- pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
- pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
- pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
- __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
- wmb();
-
- /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
- * CPU clock; all other clock generators off/unused.
- */
- div = (get_au1x00_speed() + 25000000) / 50000000;
- if (div & 1)
- div++;
- div = ((div >> 1) - 1) & 0xff;
-
- freq0 = div << SYS_FC_FRDIV0_BIT;
- __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
- wmb();
- freq0 |= SYS_FC_FE0; /* enable F0 */
- __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
- wmb();
-
- /* psc0_intclk comes 1:1 from F0 */
- clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
- __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
- wmb();
-}
-
-static int __init db1200_arch_init(void)
-{
- /* GPIO7 is low-level triggered CPLD cascade */
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
-
- /* insert/eject pairs: one of both is always screaming. To avoid
- * issues they must not be automatically enabled when initially
- * requested.
- */
- irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
- return 0;
-}
-arch_initcall(db1200_arch_init);
diff --git a/arch/mips/alchemy/devboards/db1x00.c b/arch/mips/alchemy/devboards/db1x00.c
new file mode 100644
index 0000000..589ae24
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1x00.c
@@ -0,0 +1,256 @@
+/*
+ * DBAu1000/1500/1100 board support
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1000_dma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
+#include <prom.h>
+#include "platform.h"
+
+struct pci_dev;
+
+const char *get_system_type(void)
+{
+ return "Alchemy Db1x00";
+}
+
+void __init board_setup(void)
+{
+#ifdef CONFIG_MIPS_DB1000
+ printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1500
+ printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1100
+ printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+#endif
+ /* initialize board register space */
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
+ {
+ u32 pin_func;
+
+ /* Set IRFIRSEL instead of GPIO15 */
+ pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
+ au_writel(pin_func, SYS_PINFUNC);
+ /* Power off until the driver is in use */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
+ BCSR_RESETS_IRDA_MODE_OFF);
+ }
+#endif
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ /* Enable GPIO[31:0] inputs */
+ alchemy_gpio1_input_enable();
+}
+
+/* DB1xxx PCMCIA interrupt sources:
+ * CD0/1 GPIO0/3
+ * STSCHG0/1 GPIO1/4
+ * CARD0/1 GPIO2/5
+ */
+
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+#if defined(CONFIG_MIPS_DB1000)
+#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
+#elif defined(CONFIG_MIPS_DB1100)
+#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
+#elif defined(CONFIG_MIPS_DB1500)
+#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
+
+static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata db1500_pci_pd = {
+ .board_map_irq = db1500_map_pci_irq,
+};
+
+static struct platform_device db1500_pci_host_dev = {
+ .dev.platform_data = &db1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init db1500_pci_init(void)
+{
+ return platform_device_register(&db1500_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(db1500_pci_init);
+#endif
+
+#ifdef CONFIG_MIPS_DB1100
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+#endif
+
+static struct resource alchemy_ac97c_res[] = {
+ [0] = {
+ .start = AU1000_AC97_PHYS_ADDR,
+ .end = AU1000_AC97_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DMA_ID_AC97C_TX,
+ .end = DMA_ID_AC97C_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = DMA_ID_AC97C_RX,
+ .end = DMA_ID_AC97C_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device alchemy_ac97c_dev = {
+ .name = "alchemy-ac97c",
+ .id = -1,
+ .resource = alchemy_ac97c_res,
+ .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
+};
+
+static struct platform_device alchemy_ac97c_dma_dev = {
+ .name = "alchemy-pcm-dma",
+ .id = 0,
+};
+
+static struct platform_device db1x00_codec_dev = {
+ .name = "ac97-codec",
+ .id = -1,
+};
+
+static struct platform_device db1x00_audio_dev = {
+ .name = "db1000-audio",
+};
+
+static int __init db1xxx_dev_init(void)
+{
+ irq_set_irq_type(DB1XXX_PCMCIA_CD0, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(DB1XXX_PCMCIA_CD1, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(DB1XXX_PCMCIA_CARD0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_CARD1, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_STSCHG0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_STSCHG1, IRQ_TYPE_LEVEL_LOW);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
+ /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
+ /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
+#ifdef CONFIG_MIPS_DB1100
+ platform_device_register(&au1100_lcd_device);
+#endif
+ platform_device_register(&db1x00_codec_dev);
+ platform_device_register(&alchemy_ac97c_dma_dev);
+ platform_device_register(&alchemy_ac97c_dev);
+ platform_device_register(&db1x00_audio_dev);
+
+ db1x_register_norflash(32 << 20, 4 /* 32bit */, F_SWAPPED);
+ return 0;
+}
+device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/db1x00/Makefile b/arch/mips/alchemy/devboards/db1x00/Makefile
deleted file mode 100644
index 613c0c0..0000000
--- a/arch/mips/alchemy/devboards/db1x00/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
deleted file mode 100644
index 2dbebcb..0000000
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ /dev/null
@@ -1,108 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Db1x00 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_eth.h>
-#include <asm/mach-db1x00/db1x00.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/reboot.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1x00";
-}
-
-
-void __init board_setup(void)
-{
-#ifdef CONFIG_MIPS_DB1000
- printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
- printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
- printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
-#endif
- /* initialize board register space */
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
-#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
- {
- u32 pin_func;
-
- /* Set IRFIRSEL instead of GPIO15 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
- au_writel(pin_func, SYS_PINFUNC);
- /* Power off until the driver is in use */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
- BCSR_RESETS_IRDA_MODE_OFF);
- }
-#endif
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- /* Enable GPIO[31:0] inputs */
- alchemy_gpio1_input_enable();
-}
-
-static int __init db1x00_init_irq(void)
-{
-#if defined(CONFIG_MIPS_DB1500)
- irq_set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1100)
- irq_set_irq_type(AU1100_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1100_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1100_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1100_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1100_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1100_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1000)
- irq_set_irq_type(AU1000_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1000_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1000_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1000_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1000_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1000_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#endif
- return 0;
-}
-arch_initcall(db1x00_init_irq);
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
deleted file mode 100644
index b439b4f..0000000
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ /dev/null
@@ -1,206 +0,0 @@
-/*
- * DBAu1xxx board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1000_dma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include "../platform.h"
-
-struct pci_dev;
-
-/* DB1xxx PCMCIA interrupt sources:
- * CD0/1 GPIO0/3
- * STSCHG0/1 GPIO1/4
- * CARD0/1 GPIO2/5
- */
-
-#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
-
-#if defined(CONFIG_MIPS_DB1000)
-#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1100)
-#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1500)
-#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
-
-static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata db1500_pci_pd = {
- .board_map_irq = db1500_map_pci_irq,
-};
-
-static struct platform_device db1500_pci_host_dev = {
- .dev.platform_data = &db1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init db1500_pci_init(void)
-{
- return platform_device_register(&db1500_pci_host_dev);
-}
-/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
-arch_initcall(db1500_pci_init);
-#endif
-
-#ifdef CONFIG_MIPS_DB1100
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-#endif
-
-static struct resource alchemy_ac97c_res[] = {
- [0] = {
- .start = AU1000_AC97_PHYS_ADDR,
- .end = AU1000_AC97_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMA_ID_AC97C_TX,
- .end = DMA_ID_AC97C_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMA_ID_AC97C_RX,
- .end = DMA_ID_AC97C_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device alchemy_ac97c_dev = {
- .name = "alchemy-ac97c",
- .id = -1,
- .resource = alchemy_ac97c_res,
- .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
-};
-
-static struct platform_device alchemy_ac97c_dma_dev = {
- .name = "alchemy-pcm-dma",
- .id = 0,
-};
-
-static struct platform_device db1x00_codec_dev = {
- .name = "ac97-codec",
- .id = -1,
-};
-
-static struct platform_device db1x00_audio_dev = {
- .name = "db1000-audio",
-};
-
-static int __init db1xxx_dev_init(void)
-{
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
- /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
- /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
-#ifdef CONFIG_MIPS_DB1100
- platform_device_register(&au1100_lcd_device);
-#endif
- platform_device_register(&db1x00_codec_dev);
- platform_device_register(&alchemy_ac97c_dma_dev);
- platform_device_register(&alchemy_ac97c_dev);
- platform_device_register(&db1x00_audio_dev);
-
- db1x_register_norflash(0x02000000, 4 /* 32bit */, F_SWAPPED);
- return 0;
-}
-device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1100.c b/arch/mips/alchemy/devboards/pb1100.c
new file mode 100644
index 0000000..cff50d0
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1100.c
@@ -0,0 +1,167 @@
+/*
+ * Pb1100 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1100";
+}
+
+void __init board_setup(void)
+{
+ volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
+
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ alchemy_gpio1_input_enable();
+ udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ {
+ u32 pin_func, sys_freqctrl, sys_clksrc;
+
+ /* Configure pins GPIO[14:9] as GPIO */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* Zero and disable USBH/USBD/IrDA clock */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+
+ /* FREQ2 = aux / 2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+ SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48 MHz FREQ2 into USBH/USBD/IrDA
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ /* Setup the static bus controller */
+ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
+ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+ /*
+ * Get USB Functionality pin state (device vs host drive pins).
+ */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host. */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+ }
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled. */
+ if (!(readb(base + 0x28) & 0x20)) {
+ writeb(readb(base + 0x28) | 0x20, base + 0x28);
+ au_sync();
+ }
+ /* Put the clock in BCD mode. */
+ if (readb(base + 0x2C) & 0x4) { /* reg B */
+ writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
+ au_sync();
+ }
+}
+
+/******************************************************************************/
+
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+
+static int __init pb1100_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
+ irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
+ irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
+ irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
+
+ /* PCMCIA. single socket, identical to Pb1500 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
+ /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&au1100_lcd_device);
+
+ return 0;
+}
+device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1100/Makefile b/arch/mips/alchemy/devboards/pb1100/Makefile
deleted file mode 100644
index 7e3756c..0000000
--- a/arch/mips/alchemy/devboards/pb1100/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1100 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1100/board_setup.c b/arch/mips/alchemy/devboards/pb1100/board_setup.c
deleted file mode 100644
index d108fd5..0000000
--- a/arch/mips/alchemy/devboards/pb1100/board_setup.c
+++ /dev/null
@@ -1,127 +0,0 @@
-/*
- * Copyright 2002, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include <prom.h>
-
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1100";
-}
-
-void __init board_setup(void)
-{
- volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
-
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- {
- u32 pin_func, sys_freqctrl, sys_clksrc;
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD/IrDA clock */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
-
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48 MHz FREQ2 into USBH/USBD/IrDA
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Get USB Functionality pin state (device vs host drive pins).
- */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host. */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
- }
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled. */
- if (!(readb(base + 0x28) & 0x20)) {
- writeb(readb(base + 0x28) | 0x20, base + 0x28);
- au_sync();
- }
- /* Put the clock in BCD mode. */
- if (readb(base + 0x2C) & 0x4) { /* reg B */
- writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
- au_sync();
- }
-}
-
-static int __init pb1100_init_irq(void)
-{
- irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
- irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
- irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
- irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
-
- return 0;
-}
-arch_initcall(pb1100_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1100/platform.c b/arch/mips/alchemy/devboards/pb1100/platform.c
deleted file mode 100644
index 9c57c01..0000000
--- a/arch/mips/alchemy/devboards/pb1100/platform.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * Pb1100 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-
-static int __init pb1100_dev_init(void)
-{
- int swapped;
-
- /* PCMCIA. single socket, identical to Pb1500 */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
- /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
- db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
- platform_device_register(&au1100_lcd_device);
-
- return 0;
-}
-device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1200.c b/arch/mips/alchemy/devboards/pb1200.c
new file mode 100644
index 0000000..a1b6497
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1200.c
@@ -0,0 +1,464 @@
+/*
+ * Pb1200/DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/leds.h>
+#include <linux/platform_device.h>
+#include <linux/smc91x.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-pb1x00/pb1200.h>
+#include <prom.h>
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "PB1200";
+}
+
+void __init board_setup(void)
+{
+ printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+ bcsr_init(PB1200_BCSR_PHYS_ADDR,
+ PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
+
+#if 0
+ {
+ u32 pin_func;
+
+ /*
+ * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
+ au_sync();
+ }
+#endif
+
+#if defined(CONFIG_I2C_AU1550)
+ {
+ u32 freq0, clksrc;
+ u32 pin_func;
+
+ /* Select SMBus in CPLD */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ /* Set GPIOs correctly */
+ pin_func |= 2 << 17;
+ au_writel(pin_func, SYS_PINFUNC);
+ au_sync();
+
+ /* The I2C driver depends on 50 MHz clock */
+ freq0 = au_readl(SYS_FREQCTRL0);
+ au_sync();
+ freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+ freq0 |= 3 << SYS_FC_FRDIV1_BIT;
+ /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+ freq0 |= SYS_FC_FE1;
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+
+ clksrc = au_readl(SYS_CLKSRC);
+ au_sync();
+ clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
+ /* Bit 22 is EXTCLK0 for PSC0 */
+ clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
+ au_writel(clksrc, SYS_CLKSRC);
+ au_sync();
+ }
+#endif
+
+ /*
+ * The Pb1200 development board uses external MUX for PSC0 to
+ * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
+ */
+#ifdef CONFIG_I2C_AU1550
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+#endif
+ au_sync();
+}
+
+/******************************************************************************/
+
+static int mmc_activity;
+
+static void pb1200mmc0_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+
+ msleep(1);
+}
+
+static int pb1200mmc0_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int pb1200mmc0_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void pb1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF) {
+ if (++mmc_activity == 1)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ } else {
+ if (--mmc_activity == 0)
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+ }
+}
+
+static struct led_classdev pb1200mmc_led = {
+ .brightness_set = pb1200_mmcled_set,
+};
+
+static void pb1200mmc1_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
+
+ msleep(1);
+}
+
+static int pb1200mmc1_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
+}
+
+static int pb1200mmc1_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
+}
+
+static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
+ [0] = {
+ .set_power = pb1200mmc0_set_power,
+ .card_inserted = pb1200mmc0_card_inserted,
+ .card_readonly = pb1200mmc0_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+ [1] = {
+ .set_power = pb1200mmc1_set_power,
+ .card_inserted = pb1200mmc1_card_inserted,
+ .card_readonly = pb1200mmc1_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct resource au1200_mmc0_res[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX0,
+ .end = AU1200_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX0,
+ .end = AU1200_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200mmc_platdata[0],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc0_res),
+ .resource = au1200_mmc0_res,
+};
+
+static struct resource au1200_mmc1_res[] = {
+ [0] = {
+ .start = AU1100_SD1_PHYS_ADDR,
+ .end = AU1100_SD1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX1,
+ .end = AU1200_DSCR_CMD0_SDMS_TX1,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX1,
+ .end = AU1200_DSCR_CMD0_SDMS_RX1,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc1_dev = {
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200mmc_platdata[1],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc1_res),
+ .resource = au1200_mmc1_res,
+};
+
+
+static struct resource ide_resources[] = {
+ [0] = {
+ .start = IDE_PHYS_ADDR,
+ .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = IDE_INT,
+ .end = IDE_INT,
+ .flags = IORESOURCE_IRQ
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_DMA_REQ1,
+ .end = AU1200_DSCR_CMD0_DMA_REQ1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device ide_device = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_ide_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(ide_resources),
+ .resource = ide_resources
+};
+
+static struct smc91x_platdata smc_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91c111_resources[] = {
+ [0] = {
+ .name = "smc91x-regs",
+ .start = SMC91C111_PHYS_ADDR,
+ .end = SMC91C111_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = SMC91C111_INT,
+ .end = SMC91C111_INT,
+ .flags = IORESOURCE_IRQ
+ },
+};
+
+static struct platform_device smc91c111_device = {
+ .dev = {
+ .platform_data = &smc_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91c111_resources),
+ .resource = smc91c111_resources
+};
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC0_TX,
+ .end = AU1200_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC0_RX,
+ .end = AU1200_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device pb1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_LCD_INT,
+ .end = AU1200_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1200_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1200_lcd_res),
+ .resource = au1200_lcd_res,
+};
+
+static struct platform_device *board_platform_devices[] __initdata = {
+ &ide_device,
+ &smc91c111_device,
+ &pb1200_i2c_dev,
+ &pb1200_mmc0_dev,
+ &pb1200_mmc1_dev,
+ &au1200_lcd_dev,
+};
+
+static int __init board_register_devices(void)
+{
+ int swapped;
+
+ /* We have a problem with CPLD rev 3. */
+ if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+ printk(KERN_ERR "updated to latest revision. This software will\n");
+ printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ panic("Game over. Your score is 0.");
+ }
+
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
+ /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
+ /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
+
+ return platform_add_devices(board_platform_devices,
+ ARRAY_SIZE(board_platform_devices));
+}
+device_initcall(board_register_devices);
+
+
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/pb1200/Makefile b/arch/mips/alchemy/devboards/pb1200/Makefile
deleted file mode 100644
index 18c1bd5..0000000
--- a/arch/mips/alchemy/devboards/pb1200/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1200/board_setup.c b/arch/mips/alchemy/devboards/pb1200/board_setup.c
deleted file mode 100644
index 6d06b07..0000000
--- a/arch/mips/alchemy/devboards/pb1200/board_setup.c
+++ /dev/null
@@ -1,174 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1200/Db1200 board setup.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1200";
-}
-
-void __init board_setup(void)
-{
- printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
- bcsr_init(PB1200_BCSR_PHYS_ADDR,
- PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
-
-#if 0
- {
- u32 pin_func;
-
- /*
- * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
- }
-#endif
-
-#if defined(CONFIG_I2C_AU1550)
- {
- u32 freq0, clksrc;
- u32 pin_func;
-
- /* Select SMBus in CPLD */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- /* Set GPIOs correctly */
- pin_func |= 2 << 17;
- au_writel(pin_func, SYS_PINFUNC);
- au_sync();
-
- /* The I2C driver depends on 50 MHz clock */
- freq0 = au_readl(SYS_FREQCTRL0);
- au_sync();
- freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
- freq0 |= 3 << SYS_FC_FRDIV1_BIT;
- /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
- freq0 |= SYS_FC_FE1;
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
-
- clksrc = au_readl(SYS_CLKSRC);
- au_sync();
- clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
- /* Bit 22 is EXTCLK0 for PSC0 */
- clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
- au_writel(clksrc, SYS_CLKSRC);
- au_sync();
- }
-#endif
-
- /*
- * The Pb1200 development board uses external MUX for PSC0 to
- * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
- */
-#ifdef CONFIG_I2C_AU1550
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-#endif
- au_sync();
-}
-
-static int __init pb1200_init_irq(void)
-{
- /* We have a problem with CPLD rev 3. */
- if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
-
- return 0;
-}
-arch_initcall(pb1200_init_irq);
-
-
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- /* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- /* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/pb1200/platform.c b/arch/mips/alchemy/devboards/pb1200/platform.c
deleted file mode 100644
index 54f7f7b..0000000
--- a/arch/mips/alchemy/devboards/pb1200/platform.c
+++ /dev/null
@@ -1,339 +0,0 @@
-/*
- * Pb1200/DBAu1200 board platform device registration
- *
- * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-pb1x00/pb1200.h>
-
-#include "../platform.h"
-
-static int mmc_activity;
-
-static void pb1200mmc0_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc0_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int pb1200mmc0_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void pb1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF) {
- if (++mmc_activity == 1)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- } else {
- if (--mmc_activity == 0)
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
- }
-}
-
-static struct led_classdev pb1200mmc_led = {
- .brightness_set = pb1200_mmcled_set,
-};
-
-static void pb1200mmc1_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc1_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
-}
-
-static int pb1200mmc1_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
-}
-
-static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
- [0] = {
- .set_power = pb1200mmc0_set_power,
- .card_inserted = pb1200mmc0_card_inserted,
- .card_readonly = pb1200mmc0_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
- [1] = {
- .set_power = pb1200mmc1_set_power,
- .card_inserted = pb1200mmc1_card_inserted,
- .card_readonly = pb1200mmc1_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct resource au1200_mmc0_res[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[0],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_res),
- .resource = au1200_mmc0_res,
-};
-
-static struct resource au1200_mmc1_res[] = {
- [0] = {
- .start = AU1100_SD1_PHYS_ADDR,
- .end = AU1100_SD1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX1,
- .end = AU1200_DSCR_CMD0_SDMS_TX1,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX1,
- .end = AU1200_DSCR_CMD0_SDMS_RX1,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc1_dev = {
- .name = "au1xxx-mmc",
- .id = 1,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[1],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc1_res),
- .resource = au1200_mmc1_res,
-};
-
-
-static struct resource ide_resources[] = {
- [0] = {
- .start = IDE_PHYS_ADDR,
- .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = IDE_INT,
- .end = IDE_INT,
- .flags = IORESOURCE_IRQ
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device ide_device = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(ide_resources),
- .resource = ide_resources
-};
-
-static struct smc91x_platdata smc_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91c111_resources[] = {
- [0] = {
- .name = "smc91x-regs",
- .start = SMC91C111_PHYS_ADDR,
- .end = SMC91C111_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = SMC91C111_INT,
- .end = SMC91C111_INT,
- .flags = IORESOURCE_IRQ
- },
-};
-
-static struct platform_device smc91c111_device = {
- .dev = {
- .platform_data = &smc_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smc91c111_resources),
- .resource = smc91c111_resources
-};
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-static struct platform_device *board_platform_devices[] __initdata = {
- &ide_device,
- &smc91c111_device,
- &pb1200_i2c_dev,
- &pb1200_mmc0_dev,
- &pb1200_mmc1_dev,
- &au1200_lcd_dev,
-};
-
-static int __init board_register_devices(void)
-{
- int swapped;
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
- /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
- /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
-
- return platform_add_devices(board_platform_devices,
- ARRAY_SIZE(board_platform_devices));
-}
-device_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/devboards/pb1500.c b/arch/mips/alchemy/devboards/pb1500.c
new file mode 100644
index 0000000..e7b807b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1500.c
@@ -0,0 +1,198 @@
+/*
+ * Pb1500 board support.
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1500";
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+ u32 sys_freqctrl, sys_clksrc;
+
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ sys_clksrc = sys_freqctrl = pin_func = 0;
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ alchemy_gpio1_input_enable();
+ udelay(100);
+
+ /* GPIO201 is input for PCMCIA card detect */
+ /* GPIO203 is input for PCMCIA interrupt request */
+ alchemy_gpio_direction_input(201);
+ alchemy_gpio_direction_input(203);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* zero and disable USBH/USBD clocks */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+
+ /* FREQ2 = aux/2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48MHz FREQ2 into USB Host and/or Device
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+#ifdef CONFIG_PCI
+ {
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
+ /* Setup PCI bus controller */
+ __raw_writel(0x00003fff, base + PCI_REG_CMEM);
+ __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
+ __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
+ __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
+ __raw_writel(0x00003c04, base + PCI_REG_PARAM);
+ __raw_writel(0x00000008, base + PCI_REG_MBAR);
+ wmb();
+ }
+#endif
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled */
+ if (!(au_readl(0xac000028) & 0x20)) {
+ printk(KERN_INFO "enabling clock ...\n");
+ au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
+ }
+ /* Put the clock in BCD mode */
+ if (au_readl(0xac00002c) & 0x4) { /* reg B */
+ au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
+ au_sync();
+ }
+}
+
+/******************************************************************************/
+
+static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1500_pci_pd = {
+ .board_map_irq = pb1500_map_pci_irq,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device pb1500_pci_host = {
+ .dev.platform_data = &pb1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init pb1500_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
+ irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+ irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+ /* PCMCIA. single socket, identical to Pb1100 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
+ /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1500_pci_host);
+
+ return 0;
+}
+arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1500/Makefile b/arch/mips/alchemy/devboards/pb1500/Makefile
deleted file mode 100644
index e83b151..0000000
--- a/arch/mips/alchemy/devboards/pb1500/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1500 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1500/board_setup.c b/arch/mips/alchemy/devboards/pb1500/board_setup.c
deleted file mode 100644
index 37c1883..0000000
--- a/arch/mips/alchemy/devboards/pb1500/board_setup.c
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1500";
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
- u32 sys_freqctrl, sys_clksrc;
-
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
- sys_clksrc = sys_freqctrl = pin_func = 0;
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
- /* GPIO201 is input for PCMCIA card detect */
- /* GPIO203 is input for PCMCIA interrupt request */
- alchemy_gpio_direction_input(201);
- alchemy_gpio_direction_input(203);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- /* FREQ2 = aux/2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
-#ifdef CONFIG_PCI
- {
- void __iomem *base =
- (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
- /* Setup PCI bus controller */
- __raw_writel(0x00003fff, base + PCI_REG_CMEM);
- __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
- __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
- __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
- __raw_writel(0x00003c04, base + PCI_REG_PARAM);
- __raw_writel(0x00000008, base + PCI_REG_MBAR);
- wmb();
- }
-#endif
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled */
- if (!(au_readl(0xac000028) & 0x20)) {
- printk(KERN_INFO "enabling clock ...\n");
- au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
- }
- /* Put the clock in BCD mode */
- if (au_readl(0xac00002c) & 0x4) { /* reg B */
- au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
- au_sync();
- }
-}
-
-static int __init pb1500_init_irq(void)
-{
- irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
- irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
- irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
-
- return 0;
-}
-arch_initcall(pb1500_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
deleted file mode 100644
index 1e52a01..0000000
--- a/arch/mips/alchemy/devboards/pb1500/platform.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * Pb1500 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata pb1500_pci_pd = {
- .board_map_irq = pb1500_map_pci_irq,
- .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
- PCI_CONFIG_CH |
-#if defined(__MIPSEB__)
- PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
-#else
- 0,
-#endif
-};
-
-static struct platform_device pb1500_pci_host = {
- .dev.platform_data = &pb1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init pb1500_dev_init(void)
-{
- int swapped;
-
- /* PCMCIA. single socket, identical to Pb1100 */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
- /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
- db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
- platform_device_register(&pb1500_pci_host);
-
- return 0;
-}
-arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550.c b/arch/mips/alchemy/devboards/pb1550.c
new file mode 100644
index 0000000..e4a00a5
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1550.c
@@ -0,0 +1,178 @@
+/*
+ * Pb1550 board support.
+ *
+ * Copyright (C) 2009-2011 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/gpio.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1550";
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+
+ bcsr_init(PB1550_BCSR_PHYS_ADDR,
+ PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+
+ alchemy_gpio2_enable();
+
+ /*
+ * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
+}
+
+/******************************************************************************/
+
+static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTB;
+ case 2: return AU1500_PCI_INTC;
+ case 3: return AU1500_PCI_INTD;
+ case 4: return AU1500_PCI_INTA;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1550_pci_pd = {
+ .board_map_irq = pb1550_map_pci_irq,
+};
+
+static struct platform_device pb1550_pci_host = {
+ .dev.platform_data = &pb1550_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static struct resource au1550_psc2_res[] = {
+ [0] = {
+ .start = AU1550_PSC2_PHYS_ADDR,
+ .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC2_INT,
+ .end = AU1550_PSC2_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC2_TX,
+ .end = AU1550_DSCR_CMD0_PSC2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC2_RX,
+ .end = AU1550_DSCR_CMD0_PSC2_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device pb1550_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1550_psc2_res),
+ .resource = au1550_psc2_res,
+};
+
+static int __init pb1550_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
+
+ /* enable both PCMCIA card irqs in the shared line */
+ alchemy_gpio2_enable_int(201);
+ alchemy_gpio2_enable_int(202);
+
+ /* Pb1550, like all others, also has statuschange irqs; however they're
+ * wired up on one of the Au1550's shared GPIO201_205 line, which also
+ * services the PCMCIA card interrupts. So we ignore statuschange and
+ * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+ * drivers are used to shared irqs and b) statuschange isn't really use-
+ * ful anyway.
+ */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1550_pci_host);
+ platform_device_register(&pb1550_i2c_dev);
+
+ return 0;
+}
+arch_initcall(pb1550_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550/Makefile b/arch/mips/alchemy/devboards/pb1550/Makefile
deleted file mode 100644
index 9661b6e..0000000
--- a/arch/mips/alchemy/devboards/pb1550/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1550 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1550/board_setup.c b/arch/mips/alchemy/devboards/pb1550/board_setup.c
deleted file mode 100644
index 0f62d1e..0000000
--- a/arch/mips/alchemy/devboards/pb1550/board_setup.c
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1550 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-au1x00/gpio.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1550";
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
-
- bcsr_init(PB1550_BCSR_PHYS_ADDR,
- PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
-
- alchemy_gpio2_enable();
-
- /*
- * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
-}
-
-static int __init pb1550_init_irq(void)
-{
- irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
-
- /* enable both PCMCIA card irqs in the shared line */
- alchemy_gpio2_enable_int(201);
- alchemy_gpio2_enable_int(202);
-
- return 0;
-}
-arch_initcall(pb1550_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
deleted file mode 100644
index a4604b8..0000000
--- a/arch/mips/alchemy/devboards/pb1550/platform.c
+++ /dev/null
@@ -1,140 +0,0 @@
-/*
- * Pb1550 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12) {
- switch (pin) {
- case 1: return AU1500_PCI_INTB;
- case 2: return AU1500_PCI_INTC;
- case 3: return AU1500_PCI_INTD;
- case 4: return AU1500_PCI_INTA;
- }
- }
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata pb1550_pci_pd = {
- .board_map_irq = pb1550_map_pci_irq,
-};
-
-static struct platform_device pb1550_pci_host = {
- .dev.platform_data = &pb1550_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static struct resource au1550_psc2_res[] = {
- [0] = {
- .start = AU1550_PSC2_PHYS_ADDR,
- .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1550_PSC2_INT,
- .end = AU1550_PSC2_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1550_DSCR_CMD0_PSC2_TX,
- .end = AU1550_DSCR_CMD0_PSC2_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1550_DSCR_CMD0_PSC2_RX,
- .end = AU1550_DSCR_CMD0_PSC2_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1550_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1550_psc2_res),
- .resource = au1550_psc2_res,
-};
-
-static int __init pb1550_dev_init(void)
-{
- int swapped;
-
- /* Pb1550, like all others, also has statuschange irqs; however they're
- * wired up on one of the Au1550's shared GPIO201_205 line, which also
- * services the PCMCIA card interrupts. So we ignore statuschange and
- * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
- * drivers are used to shared irqs and b) statuschange isn't really use-
- * ful anyway.
- */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
- platform_device_register(&pb1550_pci_host);
- platform_device_register(&pb1550_i2c_dev);
-
- return 0;
-}
-arch_initcall(pb1550_dev_init);
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 09/18] MIPS: Alchemy: move au1200fb global functions to platform data
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-01 19:03 ` [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support Manuel Lauss
` (16 subsequent siblings)
17 siblings, 0 replies; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss, linux-fbdev
au1200fb calls 3 functions which have to be defined in board code.
Fix this ugliness with the introduction of platform_data.
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
I'd like this to go in via the MIPS tree since patches depend on it.
arch/mips/alchemy/devboards/db1200.c | 51 +++---
arch/mips/alchemy/devboards/db1300.c | 52 +++---
arch/mips/alchemy/devboards/pb1200.c | 55 ++++---
arch/mips/include/asm/mach-au1x00/au1200fb.h | 14 ++
drivers/video/au1200fb.c | 241 ++++++++++++--------------
5 files changed, 213 insertions(+), 200 deletions(-)
create mode 100644 arch/mips/include/asm/mach-au1x00/au1200fb.h
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
index 43f5f1b..e2cc5f9 100644
--- a/arch/mips/alchemy/devboards/db1200.c
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -37,6 +37,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1100_mmc.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1200fb.h>
#include <asm/mach-au1x00/au1550_spi.h>
#include <asm/mach-db1x00/bcsr.h>
#include <asm/mach-db1x00/db1200.h>
@@ -422,6 +423,33 @@ static struct platform_device db1200_mmc0_dev = {
/**********************************************************************/
+static int db1200fb_panel_index(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+static int db1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+static int db1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
+
+static struct au1200fb_platdata db1200fb_pd = {
+ .panel_index = db1200fb_panel_index,
+ .panel_init = db1200fb_panel_init,
+ .panel_shutdown = db1200fb_panel_shutdown,
+};
+
static struct resource au1200_lcd_res[] = {
[0] = {
.start = AU1200_LCD_PHYS_ADDR,
@@ -443,6 +471,7 @@ static struct platform_device au1200_lcd_dev = {
.dev = {
.dma_mask = &au1200_lcd_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200fb_pd,
},
.num_resources = ARRAY_SIZE(au1200_lcd_res),
.resource = au1200_lcd_res,
@@ -681,25 +710,3 @@ static int __init db1200_dev_init(void)
return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
}
device_initcall(db1200_dev_init);
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
index bf0d1c4..d1a7344 100644
--- a/arch/mips/alchemy/devboards/db1300.c
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -22,6 +22,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1200fb.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-au1x00/au1xxx_psc.h>
#include <asm/mach-db1x00/db1300.h>
@@ -635,6 +636,33 @@ static struct platform_device db1300_sndi2s_dev = {
/**********************************************************************/
+static int db1300fb_panel_index(void)
+{
+ return 9; /* DB1300_800x480 */
+}
+
+static int db1300fb_panel_init(void)
+{
+ /* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+static int db1300fb_panel_shutdown(void)
+{
+ /* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
+ BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
+ return 0;
+}
+
+static struct au1200fb_platdata db1300fb_pd = {
+ .panel_index = db1300fb_panel_index,
+ .panel_init = db1300fb_panel_init,
+ .panel_shutdown = db1300fb_panel_shutdown,
+};
+
static struct resource au1300_lcd_res[] = {
[0] = {
.start = AU1200_LCD_PHYS_ADDR,
@@ -656,6 +684,7 @@ static struct platform_device db1300_lcd_dev = {
.dev = {
.dma_mask = &au1300_lcd_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1300fb_pd,
},
.num_resources = ARRAY_SIZE(au1300_lcd_res),
.resource = au1300_lcd_res,
@@ -761,26 +790,3 @@ void __init board_setup(void)
alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
}
-
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return 9; /* DB1300_800x480 */
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
- BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/pb1200.c b/arch/mips/alchemy/devboards/pb1200.c
index a1b6497..a2676c9 100644
--- a/arch/mips/alchemy/devboards/pb1200.c
+++ b/arch/mips/alchemy/devboards/pb1200.c
@@ -26,6 +26,7 @@
#include <linux/smc91x.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1200fb.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-db1x00/bcsr.h>
#include <asm/mach-pb1x00/pb1200.h>
@@ -351,6 +352,33 @@ static struct platform_device pb1200_i2c_dev = {
.resource = au1200_psc0_res,
};
+static int pb1200fb_panel_index(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+static int pb1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+static int pb1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
+
+static struct au1200fb_platdata pb1200fb_pd = {
+ .panel_index = pb1200fb_panel_index,
+ .panel_init = pb1200fb_panel_init,
+ .panel_shutdown = pb1200fb_panel_shutdown,
+};
+
static struct resource au1200_lcd_res[] = {
[0] = {
.start = AU1200_LCD_PHYS_ADDR,
@@ -366,12 +394,13 @@ static struct resource au1200_lcd_res[] = {
static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-static struct platform_device au1200_lcd_dev = {
+static struct platform_device pb1200_lcd_dev = {
.name = "au1200-lcd",
.id = 0,
.dev = {
.dma_mask = &au1200_lcd_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200fb_pd,
},
.num_resources = ARRAY_SIZE(au1200_lcd_res),
.resource = au1200_lcd_res,
@@ -383,7 +412,7 @@ static struct platform_device *board_platform_devices[] __initdata = {
&pb1200_i2c_dev,
&pb1200_mmc0_dev,
&pb1200_mmc1_dev,
- &au1200_lcd_dev,
+ &pb1200_lcd_dev,
};
static int __init board_register_devices(void)
@@ -440,25 +469,3 @@ static int __init board_register_devices(void)
ARRAY_SIZE(board_platform_devices));
}
device_initcall(board_register_devices);
-
-
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/include/asm/mach-au1x00/au1200fb.h b/arch/mips/include/asm/mach-au1x00/au1200fb.h
new file mode 100644
index 0000000..b3c87cc
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1200fb.h
@@ -0,0 +1,14 @@
+/*
+ * platform data for au1200fb driver.
+ */
+
+#ifndef _AU1200FB_PLAT_H_
+#define _AU1200FB_PLAT_H_
+
+struct au1200fb_platdata {
+ int (*panel_index)(void);
+ int (*panel_init)(void);
+ int (*panel_shutdown)(void);
+};
+
+#endif
diff --git a/drivers/video/au1200fb.c b/drivers/video/au1200fb.c
index 6c4342f..04e4479 100644
--- a/drivers/video/au1200fb.c
+++ b/drivers/video/au1200fb.c
@@ -44,6 +44,7 @@
#include <linux/slab.h>
#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1200fb.h> /* platform_data */
#include "au1200fb.h"
#define DRIVER_NAME "au1200fb"
@@ -143,6 +144,7 @@ struct au1200_lcd_iodata_t {
/* Private, per-framebuffer management information (independent of the panel itself) */
struct au1200fb_device {
struct fb_info *fb_info; /* FB driver info record */
+ struct au1200fb_platdata *pd;
int plane;
unsigned char* fb_mem; /* FrameBuffer memory map */
@@ -201,9 +203,6 @@ struct window_settings {
#define LCD_WINCTRL1_PO_16BPP LCD_WINCTRL1_PO_01
#endif
-extern int board_au1200fb_panel_init (void);
-extern int board_au1200fb_panel_shutdown (void);
-
/*
* Default window configurations
*/
@@ -334,8 +333,6 @@ struct panel_settings
uint32 mode_toyclksrc;
uint32 mode_backlight;
uint32 mode_auxpll;
- int (*device_init)(void);
- int (*device_shutdown)(void);
#define Xres min_xres
#define Yres min_yres
u32 min_xres; /* Minimum horizontal resolution */
@@ -385,8 +382,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
320, 320,
240, 240,
},
@@ -415,8 +410,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
640, 480,
640, 480,
},
@@ -445,8 +438,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
800, 800,
600, 600,
},
@@ -475,8 +466,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 6, /* 72MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
1024, 1024,
768, 768,
},
@@ -505,8 +494,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 10, /* 120MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
1280, 1280,
1024, 1024,
},
@@ -535,8 +522,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
1024, 1024,
768, 768,
},
@@ -568,8 +553,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
640, 480,
640, 480,
},
@@ -601,8 +584,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
320, 320,
240, 240,
},
@@ -634,8 +615,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
856, 856,
480, 480,
},
@@ -670,8 +649,6 @@ static struct panel_settings known_lcd_panels[] =
.mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = (48/12) * 2,
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
800, 800,
480, 480,
},
@@ -800,7 +777,8 @@ static int au1200_setlocation (struct au1200fb_device *fbdev, int plane,
return 0;
}
-static void au1200_setpanel (struct panel_settings *newpanel)
+static void au1200_setpanel(struct panel_settings *newpanel,
+ struct au1200fb_platdata *pd)
{
/*
* Perform global setup/init of LCD controller
@@ -834,8 +812,8 @@ static void au1200_setpanel (struct panel_settings *newpanel)
the controller, the clock cannot be turned off before first
shutting down the controller.
*/
- if (panel->device_shutdown != NULL)
- panel->device_shutdown();
+ if (pd->panel_shutdown)
+ pd->panel_shutdown();
}
/* Newpanel == NULL indicates a shutdown operation only */
@@ -888,7 +866,8 @@ static void au1200_setpanel (struct panel_settings *newpanel)
au_sync();
/* Call init of panel */
- if (panel->device_init != NULL) panel->device_init();
+ if (pd->panel_init)
+ pd->panel_init();
/* FIX!!!! not appropriate on panel change!!! Global setup/init */
lcd->intenable = 0;
@@ -1221,6 +1200,8 @@ static int au1200fb_fb_setcolreg(unsigned regno, unsigned red, unsigned green,
*/
static int au1200fb_fb_blank(int blank_mode, struct fb_info *fbi)
{
+ struct au1200fb_device *fbdev = fbi->par;
+
/* Short-circuit screen blanking */
if (noblanking)
return 0;
@@ -1230,13 +1211,13 @@ static int au1200fb_fb_blank(int blank_mode, struct fb_info *fbi)
case FB_BLANK_UNBLANK:
case FB_BLANK_NORMAL:
/* printk("turn on panel\n"); */
- au1200_setpanel(panel);
+ au1200_setpanel(panel, fbdev->pd);
break;
case FB_BLANK_VSYNC_SUSPEND:
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_POWERDOWN:
/* printk("turn off panel\n"); */
- au1200_setpanel(NULL);
+ au1200_setpanel(NULL, fbdev->pd);
break;
default:
break;
@@ -1464,6 +1445,7 @@ static void get_window(unsigned int plane,
static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd,
unsigned long arg)
{
+ struct au1200fb_device *fbdev = info->par;
int plane;
int val;
@@ -1508,7 +1490,7 @@ static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd,
struct panel_settings *newpanel;
panel_index = iodata.global.panel_choice;
newpanel = &known_lcd_panels[panel_index];
- au1200_setpanel(newpanel);
+ au1200_setpanel(newpanel, fbdev->pd);
}
break;
@@ -1624,22 +1606,102 @@ static int au1200fb_init_fbinfo(struct au1200fb_device *fbdev)
/*-------------------------------------------------------------------------*/
-/* AU1200 LCD controller device driver */
+static int au1200fb_setup(struct au1200fb_platdata *pd)
+{
+ char *options = NULL;
+ char *this_opt, *endptr;
+ int num_panels = ARRAY_SIZE(known_lcd_panels);
+ int panel_idx = -1;
+
+ fb_get_options(DRIVER_NAME, &options);
+
+ if (!options)
+ goto out;
+
+ while ((this_opt = strsep(&options, ",")) != NULL) {
+ /* Panel option - can be panel name,
+ * "bs" for board-switch, or number/index */
+ if (!strncmp(this_opt, "panel:", 6)) {
+ int i;
+ long int li;
+ char *endptr;
+ this_opt += 6;
+ /* First check for index, which allows
+ * to short circuit this mess */
+ li = simple_strtol(this_opt, &endptr, 0);
+ if (*endptr == '\0')
+ panel_idx = (int)li;
+ else if (strcmp(this_opt, "bs") == 0)
+ panel_idx = pd->panel_index();
+ else {
+ for (i = 0; i < num_panels; i++) {
+ if (!strcmp(this_opt,
+ known_lcd_panels[i].name)) {
+ panel_idx = i;
+ break;
+ }
+ }
+ }
+ if ((panel_idx < 0) || (panel_idx >= num_panels))
+ print_warn("Panel %s not supported!", this_opt);
+ else
+ panel_index = panel_idx;
+
+ } else if (strncmp(this_opt, "nohwcursor", 10) == 0)
+ nohwcursor = 1;
+ else if (strncmp(this_opt, "devices:", 8) == 0) {
+ this_opt += 8;
+ device_count = simple_strtol(this_opt, &endptr, 0);
+ if ((device_count < 0) ||
+ (device_count > MAX_DEVICE_COUNT))
+ device_count = MAX_DEVICE_COUNT;
+ } else if (strncmp(this_opt, "wincfg:", 7) == 0) {
+ this_opt += 7;
+ window_index = simple_strtol(this_opt, &endptr, 0);
+ if ((window_index < 0) ||
+ (window_index >= ARRAY_SIZE(windows)))
+ window_index = DEFAULT_WINDOW_INDEX;
+ } else if (strncmp(this_opt, "off", 3) == 0)
+ return 1;
+ else
+ print_warn("Unsupported option \"%s\"", this_opt);
+ }
+
+out:
+ return 0;
+}
+
+/* AU1200 LCD controller device driver */
static int __devinit au1200fb_drv_probe(struct platform_device *dev)
{
struct au1200fb_device *fbdev;
+ struct au1200fb_platdata *pd;
struct fb_info *fbi = NULL;
unsigned long page;
int bpp, plane, ret, irq;
+ print_info("" DRIVER_DESC "");
+
+ pd = dev->dev.platform_data;
+ if (!pd)
+ return -ENODEV;
+
+ /* Setup driver with options */
+ if (au1200fb_setup(pd))
+ return -ENODEV;
+
+ /* Point to the panel selected */
+ panel = &known_lcd_panels[panel_index];
+ win = &windows[window_index];
+
+ printk(DRIVER_NAME ": Panel %d %s\n", panel_index, panel->name);
+ printk(DRIVER_NAME ": Win %d %s\n", window_index, win->name);
+
/* shut gcc up */
ret = 0;
fbdev = NULL;
- /* Kickstart the panel */
- au1200_setpanel(panel);
-
for (plane = 0; plane < device_count; ++plane) {
bpp = winbpp(win->w[plane].mode_winctrl1);
if (win->w[plane].xres == 0)
@@ -1655,6 +1717,7 @@ static int __devinit au1200fb_drv_probe(struct platform_device *dev)
_au1200fb_infos[plane] = fbi;
fbdev = fbi->par;
fbdev->fb_info = fbi;
+ fbdev->pd = pd;
fbdev->plane = plane;
@@ -1716,6 +1779,11 @@ static int __devinit au1200fb_drv_probe(struct platform_device *dev)
goto failed;
}
+ platform_set_drvdata(dev, pd);
+
+ /* Kickstart the panel */
+ au1200_setpanel(panel, pd);
+
return 0;
failed:
@@ -1735,12 +1803,13 @@ failed:
static int __devexit au1200fb_drv_remove(struct platform_device *dev)
{
+ struct au1200fb_platdata *pd = platform_get_drvdata(dev);
struct au1200fb_device *fbdev;
struct fb_info *fbi;
int plane;
/* Turn off the panel */
- au1200_setpanel(NULL);
+ au1200_setpanel(NULL, pd);
for (plane = 0; plane < device_count; ++plane) {
fbi = _au1200fb_infos[plane];
@@ -1768,7 +1837,8 @@ static int __devexit au1200fb_drv_remove(struct platform_device *dev)
#ifdef CONFIG_PM
static int au1200fb_drv_suspend(struct device *dev)
{
- au1200_setpanel(NULL);
+ struct au1200fb_platdata *pd = dev_get_drvdata(dev);
+ au1200_setpanel(NULL, pd);
lcd->outmask = 0;
au_sync();
@@ -1778,11 +1848,12 @@ static int au1200fb_drv_suspend(struct device *dev)
static int au1200fb_drv_resume(struct device *dev)
{
+ struct au1200fb_platdata *pd = dev_get_drvdata(dev);
struct fb_info *fbi;
int i;
/* Kickstart the panel */
- au1200_setpanel(panel);
+ au1200_setpanel(panel, pd);
for (i = 0; i < device_count; i++) {
fbi = _au1200fb_infos[i];
@@ -1817,100 +1888,8 @@ static struct platform_driver au1200fb_driver = {
/*-------------------------------------------------------------------------*/
-/* Kernel driver */
-
-static int au1200fb_setup(void)
-{
- char *options = NULL;
- char *this_opt, *endptr;
- int num_panels = ARRAY_SIZE(known_lcd_panels);
- int panel_idx = -1;
-
- fb_get_options(DRIVER_NAME, &options);
-
- if (options) {
- while ((this_opt = strsep(&options,",")) != NULL) {
- /* Panel option - can be panel name,
- * "bs" for board-switch, or number/index */
- if (!strncmp(this_opt, "panel:", 6)) {
- int i;
- long int li;
- char *endptr;
- this_opt += 6;
- /* First check for index, which allows
- * to short circuit this mess */
- li = simple_strtol(this_opt, &endptr, 0);
- if (*endptr == '\0') {
- panel_idx = (int)li;
- }
- else if (strcmp(this_opt, "bs") == 0) {
- extern int board_au1200fb_panel(void);
- panel_idx = board_au1200fb_panel();
- }
-
- else
- for (i = 0; i < num_panels; i++) {
- if (!strcmp(this_opt, known_lcd_panels[i].name)) {
- panel_idx = i;
- break;
- }
- }
-
- if ((panel_idx < 0) || (panel_idx >= num_panels)) {
- print_warn("Panel %s not supported!", this_opt);
- }
- else
- panel_index = panel_idx;
- }
-
- else if (strncmp(this_opt, "nohwcursor", 10) == 0) {
- nohwcursor = 1;
- }
-
- else if (strncmp(this_opt, "devices:", 8) == 0) {
- this_opt += 8;
- device_count = simple_strtol(this_opt,
- &endptr, 0);
- if ((device_count < 0) ||
- (device_count > MAX_DEVICE_COUNT))
- device_count = MAX_DEVICE_COUNT;
- }
-
- else if (strncmp(this_opt, "wincfg:", 7) == 0) {
- this_opt += 7;
- window_index = simple_strtol(this_opt,
- &endptr, 0);
- if ((window_index < 0) ||
- (window_index >= ARRAY_SIZE(windows)))
- window_index = DEFAULT_WINDOW_INDEX;
- }
-
- else if (strncmp(this_opt, "off", 3) == 0)
- return 1;
- /* Unsupported option */
- else {
- print_warn("Unsupported option \"%s\"", this_opt);
- }
- }
- }
- return 0;
-}
-
static int __init au1200fb_init(void)
{
- print_info("" DRIVER_DESC "");
-
- /* Setup driver with options */
- if (au1200fb_setup())
- return -ENODEV;
-
- /* Point to the panel selected */
- panel = &known_lcd_panels[panel_index];
- win = &windows[window_index];
-
- printk(DRIVER_NAME ": Panel %d %s\n", panel_index, panel->name);
- printk(DRIVER_NAME ": Win %d %s\n", window_index, win->name);
-
return platform_driver_register(&au1200fb_driver);
}
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 09/18] MIPS: Alchemy: move au1200fb global functions to platform data
@ 2011-11-01 19:03 ` Manuel Lauss
0 siblings, 0 replies; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss, linux-fbdev
au1200fb calls 3 functions which have to be defined in board code.
Fix this ugliness with the introduction of platform_data.
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
I'd like this to go in via the MIPS tree since patches depend on it.
arch/mips/alchemy/devboards/db1200.c | 51 +++---
arch/mips/alchemy/devboards/db1300.c | 52 +++---
arch/mips/alchemy/devboards/pb1200.c | 55 ++++---
arch/mips/include/asm/mach-au1x00/au1200fb.h | 14 ++
drivers/video/au1200fb.c | 241 ++++++++++++--------------
5 files changed, 213 insertions(+), 200 deletions(-)
create mode 100644 arch/mips/include/asm/mach-au1x00/au1200fb.h
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
index 43f5f1b..e2cc5f9 100644
--- a/arch/mips/alchemy/devboards/db1200.c
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -37,6 +37,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1100_mmc.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1200fb.h>
#include <asm/mach-au1x00/au1550_spi.h>
#include <asm/mach-db1x00/bcsr.h>
#include <asm/mach-db1x00/db1200.h>
@@ -422,6 +423,33 @@ static struct platform_device db1200_mmc0_dev = {
/**********************************************************************/
+static int db1200fb_panel_index(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+static int db1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+static int db1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
+
+static struct au1200fb_platdata db1200fb_pd = {
+ .panel_index = db1200fb_panel_index,
+ .panel_init = db1200fb_panel_init,
+ .panel_shutdown = db1200fb_panel_shutdown,
+};
+
static struct resource au1200_lcd_res[] = {
[0] = {
.start = AU1200_LCD_PHYS_ADDR,
@@ -443,6 +471,7 @@ static struct platform_device au1200_lcd_dev = {
.dev = {
.dma_mask = &au1200_lcd_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200fb_pd,
},
.num_resources = ARRAY_SIZE(au1200_lcd_res),
.resource = au1200_lcd_res,
@@ -681,25 +710,3 @@ static int __init db1200_dev_init(void)
return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
}
device_initcall(db1200_dev_init);
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
index bf0d1c4..d1a7344 100644
--- a/arch/mips/alchemy/devboards/db1300.c
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -22,6 +22,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1200fb.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-au1x00/au1xxx_psc.h>
#include <asm/mach-db1x00/db1300.h>
@@ -635,6 +636,33 @@ static struct platform_device db1300_sndi2s_dev = {
/**********************************************************************/
+static int db1300fb_panel_index(void)
+{
+ return 9; /* DB1300_800x480 */
+}
+
+static int db1300fb_panel_init(void)
+{
+ /* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+static int db1300fb_panel_shutdown(void)
+{
+ /* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
+ BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
+ return 0;
+}
+
+static struct au1200fb_platdata db1300fb_pd = {
+ .panel_index = db1300fb_panel_index,
+ .panel_init = db1300fb_panel_init,
+ .panel_shutdown = db1300fb_panel_shutdown,
+};
+
static struct resource au1300_lcd_res[] = {
[0] = {
.start = AU1200_LCD_PHYS_ADDR,
@@ -656,6 +684,7 @@ static struct platform_device db1300_lcd_dev = {
.dev = {
.dma_mask = &au1300_lcd_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1300fb_pd,
},
.num_resources = ARRAY_SIZE(au1300_lcd_res),
.resource = au1300_lcd_res,
@@ -761,26 +790,3 @@ void __init board_setup(void)
alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
}
-
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return 9; /* DB1300_800x480 */
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
- BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/pb1200.c b/arch/mips/alchemy/devboards/pb1200.c
index a1b6497..a2676c9 100644
--- a/arch/mips/alchemy/devboards/pb1200.c
+++ b/arch/mips/alchemy/devboards/pb1200.c
@@ -26,6 +26,7 @@
#include <linux/smc91x.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1200fb.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-db1x00/bcsr.h>
#include <asm/mach-pb1x00/pb1200.h>
@@ -351,6 +352,33 @@ static struct platform_device pb1200_i2c_dev = {
.resource = au1200_psc0_res,
};
+static int pb1200fb_panel_index(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+static int pb1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+static int pb1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
+
+static struct au1200fb_platdata pb1200fb_pd = {
+ .panel_index = pb1200fb_panel_index,
+ .panel_init = pb1200fb_panel_init,
+ .panel_shutdown = pb1200fb_panel_shutdown,
+};
+
static struct resource au1200_lcd_res[] = {
[0] = {
.start = AU1200_LCD_PHYS_ADDR,
@@ -366,12 +394,13 @@ static struct resource au1200_lcd_res[] = {
static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-static struct platform_device au1200_lcd_dev = {
+static struct platform_device pb1200_lcd_dev = {
.name = "au1200-lcd",
.id = 0,
.dev = {
.dma_mask = &au1200_lcd_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200fb_pd,
},
.num_resources = ARRAY_SIZE(au1200_lcd_res),
.resource = au1200_lcd_res,
@@ -383,7 +412,7 @@ static struct platform_device *board_platform_devices[] __initdata = {
&pb1200_i2c_dev,
&pb1200_mmc0_dev,
&pb1200_mmc1_dev,
- &au1200_lcd_dev,
+ &pb1200_lcd_dev,
};
static int __init board_register_devices(void)
@@ -440,25 +469,3 @@ static int __init board_register_devices(void)
ARRAY_SIZE(board_platform_devices));
}
device_initcall(board_register_devices);
-
-
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/include/asm/mach-au1x00/au1200fb.h b/arch/mips/include/asm/mach-au1x00/au1200fb.h
new file mode 100644
index 0000000..b3c87cc
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1200fb.h
@@ -0,0 +1,14 @@
+/*
+ * platform data for au1200fb driver.
+ */
+
+#ifndef _AU1200FB_PLAT_H_
+#define _AU1200FB_PLAT_H_
+
+struct au1200fb_platdata {
+ int (*panel_index)(void);
+ int (*panel_init)(void);
+ int (*panel_shutdown)(void);
+};
+
+#endif
diff --git a/drivers/video/au1200fb.c b/drivers/video/au1200fb.c
index 6c4342f..04e4479 100644
--- a/drivers/video/au1200fb.c
+++ b/drivers/video/au1200fb.c
@@ -44,6 +44,7 @@
#include <linux/slab.h>
#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1200fb.h> /* platform_data */
#include "au1200fb.h"
#define DRIVER_NAME "au1200fb"
@@ -143,6 +144,7 @@ struct au1200_lcd_iodata_t {
/* Private, per-framebuffer management information (independent of the panel itself) */
struct au1200fb_device {
struct fb_info *fb_info; /* FB driver info record */
+ struct au1200fb_platdata *pd;
int plane;
unsigned char* fb_mem; /* FrameBuffer memory map */
@@ -201,9 +203,6 @@ struct window_settings {
#define LCD_WINCTRL1_PO_16BPP LCD_WINCTRL1_PO_01
#endif
-extern int board_au1200fb_panel_init (void);
-extern int board_au1200fb_panel_shutdown (void);
-
/*
* Default window configurations
*/
@@ -334,8 +333,6 @@ struct panel_settings
uint32 mode_toyclksrc;
uint32 mode_backlight;
uint32 mode_auxpll;
- int (*device_init)(void);
- int (*device_shutdown)(void);
#define Xres min_xres
#define Yres min_yres
u32 min_xres; /* Minimum horizontal resolution */
@@ -385,8 +382,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
320, 320,
240, 240,
},
@@ -415,8 +410,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
640, 480,
640, 480,
},
@@ -445,8 +438,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
800, 800,
600, 600,
},
@@ -475,8 +466,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 6, /* 72MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
1024, 1024,
768, 768,
},
@@ -505,8 +494,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 10, /* 120MHz AUXPLL */
- .device_init = NULL,
- .device_shutdown = NULL,
1280, 1280,
1024, 1024,
},
@@ -535,8 +522,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
1024, 1024,
768, 768,
},
@@ -568,8 +553,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
640, 480,
640, 480,
},
@@ -601,8 +584,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
320, 320,
240, 240,
},
@@ -634,8 +615,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = 8, /* 96MHz AUXPLL */
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
856, 856,
480, 480,
},
@@ -670,8 +649,6 @@ static struct panel_settings known_lcd_panels[] .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
.mode_backlight = 0x00000000,
.mode_auxpll = (48/12) * 2,
- .device_init = board_au1200fb_panel_init,
- .device_shutdown = board_au1200fb_panel_shutdown,
800, 800,
480, 480,
},
@@ -800,7 +777,8 @@ static int au1200_setlocation (struct au1200fb_device *fbdev, int plane,
return 0;
}
-static void au1200_setpanel (struct panel_settings *newpanel)
+static void au1200_setpanel(struct panel_settings *newpanel,
+ struct au1200fb_platdata *pd)
{
/*
* Perform global setup/init of LCD controller
@@ -834,8 +812,8 @@ static void au1200_setpanel (struct panel_settings *newpanel)
the controller, the clock cannot be turned off before first
shutting down the controller.
*/
- if (panel->device_shutdown != NULL)
- panel->device_shutdown();
+ if (pd->panel_shutdown)
+ pd->panel_shutdown();
}
/* Newpanel = NULL indicates a shutdown operation only */
@@ -888,7 +866,8 @@ static void au1200_setpanel (struct panel_settings *newpanel)
au_sync();
/* Call init of panel */
- if (panel->device_init != NULL) panel->device_init();
+ if (pd->panel_init)
+ pd->panel_init();
/* FIX!!!! not appropriate on panel change!!! Global setup/init */
lcd->intenable = 0;
@@ -1221,6 +1200,8 @@ static int au1200fb_fb_setcolreg(unsigned regno, unsigned red, unsigned green,
*/
static int au1200fb_fb_blank(int blank_mode, struct fb_info *fbi)
{
+ struct au1200fb_device *fbdev = fbi->par;
+
/* Short-circuit screen blanking */
if (noblanking)
return 0;
@@ -1230,13 +1211,13 @@ static int au1200fb_fb_blank(int blank_mode, struct fb_info *fbi)
case FB_BLANK_UNBLANK:
case FB_BLANK_NORMAL:
/* printk("turn on panel\n"); */
- au1200_setpanel(panel);
+ au1200_setpanel(panel, fbdev->pd);
break;
case FB_BLANK_VSYNC_SUSPEND:
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_POWERDOWN:
/* printk("turn off panel\n"); */
- au1200_setpanel(NULL);
+ au1200_setpanel(NULL, fbdev->pd);
break;
default:
break;
@@ -1464,6 +1445,7 @@ static void get_window(unsigned int plane,
static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd,
unsigned long arg)
{
+ struct au1200fb_device *fbdev = info->par;
int plane;
int val;
@@ -1508,7 +1490,7 @@ static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd,
struct panel_settings *newpanel;
panel_index = iodata.global.panel_choice;
newpanel = &known_lcd_panels[panel_index];
- au1200_setpanel(newpanel);
+ au1200_setpanel(newpanel, fbdev->pd);
}
break;
@@ -1624,22 +1606,102 @@ static int au1200fb_init_fbinfo(struct au1200fb_device *fbdev)
/*-------------------------------------------------------------------------*/
-/* AU1200 LCD controller device driver */
+static int au1200fb_setup(struct au1200fb_platdata *pd)
+{
+ char *options = NULL;
+ char *this_opt, *endptr;
+ int num_panels = ARRAY_SIZE(known_lcd_panels);
+ int panel_idx = -1;
+
+ fb_get_options(DRIVER_NAME, &options);
+
+ if (!options)
+ goto out;
+
+ while ((this_opt = strsep(&options, ",")) != NULL) {
+ /* Panel option - can be panel name,
+ * "bs" for board-switch, or number/index */
+ if (!strncmp(this_opt, "panel:", 6)) {
+ int i;
+ long int li;
+ char *endptr;
+ this_opt += 6;
+ /* First check for index, which allows
+ * to short circuit this mess */
+ li = simple_strtol(this_opt, &endptr, 0);
+ if (*endptr = '\0')
+ panel_idx = (int)li;
+ else if (strcmp(this_opt, "bs") = 0)
+ panel_idx = pd->panel_index();
+ else {
+ for (i = 0; i < num_panels; i++) {
+ if (!strcmp(this_opt,
+ known_lcd_panels[i].name)) {
+ panel_idx = i;
+ break;
+ }
+ }
+ }
+ if ((panel_idx < 0) || (panel_idx >= num_panels))
+ print_warn("Panel %s not supported!", this_opt);
+ else
+ panel_index = panel_idx;
+
+ } else if (strncmp(this_opt, "nohwcursor", 10) = 0)
+ nohwcursor = 1;
+ else if (strncmp(this_opt, "devices:", 8) = 0) {
+ this_opt += 8;
+ device_count = simple_strtol(this_opt, &endptr, 0);
+ if ((device_count < 0) ||
+ (device_count > MAX_DEVICE_COUNT))
+ device_count = MAX_DEVICE_COUNT;
+ } else if (strncmp(this_opt, "wincfg:", 7) = 0) {
+ this_opt += 7;
+ window_index = simple_strtol(this_opt, &endptr, 0);
+ if ((window_index < 0) ||
+ (window_index >= ARRAY_SIZE(windows)))
+ window_index = DEFAULT_WINDOW_INDEX;
+ } else if (strncmp(this_opt, "off", 3) = 0)
+ return 1;
+ else
+ print_warn("Unsupported option \"%s\"", this_opt);
+ }
+
+out:
+ return 0;
+}
+
+/* AU1200 LCD controller device driver */
static int __devinit au1200fb_drv_probe(struct platform_device *dev)
{
struct au1200fb_device *fbdev;
+ struct au1200fb_platdata *pd;
struct fb_info *fbi = NULL;
unsigned long page;
int bpp, plane, ret, irq;
+ print_info("" DRIVER_DESC "");
+
+ pd = dev->dev.platform_data;
+ if (!pd)
+ return -ENODEV;
+
+ /* Setup driver with options */
+ if (au1200fb_setup(pd))
+ return -ENODEV;
+
+ /* Point to the panel selected */
+ panel = &known_lcd_panels[panel_index];
+ win = &windows[window_index];
+
+ printk(DRIVER_NAME ": Panel %d %s\n", panel_index, panel->name);
+ printk(DRIVER_NAME ": Win %d %s\n", window_index, win->name);
+
/* shut gcc up */
ret = 0;
fbdev = NULL;
- /* Kickstart the panel */
- au1200_setpanel(panel);
-
for (plane = 0; plane < device_count; ++plane) {
bpp = winbpp(win->w[plane].mode_winctrl1);
if (win->w[plane].xres = 0)
@@ -1655,6 +1717,7 @@ static int __devinit au1200fb_drv_probe(struct platform_device *dev)
_au1200fb_infos[plane] = fbi;
fbdev = fbi->par;
fbdev->fb_info = fbi;
+ fbdev->pd = pd;
fbdev->plane = plane;
@@ -1716,6 +1779,11 @@ static int __devinit au1200fb_drv_probe(struct platform_device *dev)
goto failed;
}
+ platform_set_drvdata(dev, pd);
+
+ /* Kickstart the panel */
+ au1200_setpanel(panel, pd);
+
return 0;
failed:
@@ -1735,12 +1803,13 @@ failed:
static int __devexit au1200fb_drv_remove(struct platform_device *dev)
{
+ struct au1200fb_platdata *pd = platform_get_drvdata(dev);
struct au1200fb_device *fbdev;
struct fb_info *fbi;
int plane;
/* Turn off the panel */
- au1200_setpanel(NULL);
+ au1200_setpanel(NULL, pd);
for (plane = 0; plane < device_count; ++plane) {
fbi = _au1200fb_infos[plane];
@@ -1768,7 +1837,8 @@ static int __devexit au1200fb_drv_remove(struct platform_device *dev)
#ifdef CONFIG_PM
static int au1200fb_drv_suspend(struct device *dev)
{
- au1200_setpanel(NULL);
+ struct au1200fb_platdata *pd = dev_get_drvdata(dev);
+ au1200_setpanel(NULL, pd);
lcd->outmask = 0;
au_sync();
@@ -1778,11 +1848,12 @@ static int au1200fb_drv_suspend(struct device *dev)
static int au1200fb_drv_resume(struct device *dev)
{
+ struct au1200fb_platdata *pd = dev_get_drvdata(dev);
struct fb_info *fbi;
int i;
/* Kickstart the panel */
- au1200_setpanel(panel);
+ au1200_setpanel(panel, pd);
for (i = 0; i < device_count; i++) {
fbi = _au1200fb_infos[i];
@@ -1817,100 +1888,8 @@ static struct platform_driver au1200fb_driver = {
/*-------------------------------------------------------------------------*/
-/* Kernel driver */
-
-static int au1200fb_setup(void)
-{
- char *options = NULL;
- char *this_opt, *endptr;
- int num_panels = ARRAY_SIZE(known_lcd_panels);
- int panel_idx = -1;
-
- fb_get_options(DRIVER_NAME, &options);
-
- if (options) {
- while ((this_opt = strsep(&options,",")) != NULL) {
- /* Panel option - can be panel name,
- * "bs" for board-switch, or number/index */
- if (!strncmp(this_opt, "panel:", 6)) {
- int i;
- long int li;
- char *endptr;
- this_opt += 6;
- /* First check for index, which allows
- * to short circuit this mess */
- li = simple_strtol(this_opt, &endptr, 0);
- if (*endptr = '\0') {
- panel_idx = (int)li;
- }
- else if (strcmp(this_opt, "bs") = 0) {
- extern int board_au1200fb_panel(void);
- panel_idx = board_au1200fb_panel();
- }
-
- else
- for (i = 0; i < num_panels; i++) {
- if (!strcmp(this_opt, known_lcd_panels[i].name)) {
- panel_idx = i;
- break;
- }
- }
-
- if ((panel_idx < 0) || (panel_idx >= num_panels)) {
- print_warn("Panel %s not supported!", this_opt);
- }
- else
- panel_index = panel_idx;
- }
-
- else if (strncmp(this_opt, "nohwcursor", 10) = 0) {
- nohwcursor = 1;
- }
-
- else if (strncmp(this_opt, "devices:", 8) = 0) {
- this_opt += 8;
- device_count = simple_strtol(this_opt,
- &endptr, 0);
- if ((device_count < 0) ||
- (device_count > MAX_DEVICE_COUNT))
- device_count = MAX_DEVICE_COUNT;
- }
-
- else if (strncmp(this_opt, "wincfg:", 7) = 0) {
- this_opt += 7;
- window_index = simple_strtol(this_opt,
- &endptr, 0);
- if ((window_index < 0) ||
- (window_index >= ARRAY_SIZE(windows)))
- window_index = DEFAULT_WINDOW_INDEX;
- }
-
- else if (strncmp(this_opt, "off", 3) = 0)
- return 1;
- /* Unsupported option */
- else {
- print_warn("Unsupported option \"%s\"", this_opt);
- }
- }
- }
- return 0;
-}
-
static int __init au1200fb_init(void)
{
- print_info("" DRIVER_DESC "");
-
- /* Setup driver with options */
- if (au1200fb_setup())
- return -ENODEV;
-
- /* Point to the panel selected */
- panel = &known_lcd_panels[panel_index];
- win = &windows[window_index];
-
- printk(DRIVER_NAME ": Panel %d %s\n", panel_index, panel->name);
- printk(DRIVER_NAME ": Win %d %s\n", window_index, win->name);
-
return platform_driver_register(&au1200fb_driver);
}
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 10/18] MIPS: Alchemy: Merge PB1200 support into DB1200 code.
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (8 preceding siblings ...)
2011-11-01 19:03 ` Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:52 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 11/18] MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100 Manuel Lauss
` (7 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Kconfig | 10 +-
arch/mips/alchemy/Platform | 9 +-
arch/mips/alchemy/devboards/Makefile | 1 -
arch/mips/alchemy/devboards/db1200.c | 245 +++++++++++++-
arch/mips/alchemy/devboards/pb1200.c | 471 ----------------------------
arch/mips/configs/pb1200_defconfig | 170 ----------
arch/mips/include/asm/mach-db1x00/db1200.h | 11 +-
arch/mips/include/asm/mach-pb1x00/pb1200.h | 139 --------
8 files changed, 238 insertions(+), 818 deletions(-)
delete mode 100644 arch/mips/alchemy/devboards/pb1200.c
delete mode 100644 arch/mips/configs/pb1200_defconfig
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1200.h
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index a1b995f..e1b3be7 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -42,7 +42,7 @@ config MIPS_DB1100
select SYS_HAS_EARLY_PRINTK
config MIPS_DB1200
- bool "Alchemy DB1200 board"
+ bool "Alchemy DB1200/PB1200 board"
select ALCHEMY_GPIOINT_AU1000
select DMA_COHERENT
select MIPS_DISABLE_OBSOLETE_IDE
@@ -85,14 +85,6 @@ config MIPS_PB1100
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_PB1200
- bool "Alchemy PB1200 board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
- select MIPS_DISABLE_OBSOLETE_IDE
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_PB1500
bool "Alchemy PB1500 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index c032f5b..bbdcc15 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -26,13 +26,6 @@ cflags-$(CONFIG_MIPS_PB1550) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1550) += 0xffffffff80100000
#
-# AMD Alchemy Pb1200 eval board
-#
-platform-$(CONFIG_MIPS_PB1200) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1200) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
-load-$(CONFIG_MIPS_PB1200) += 0xffffffff80100000
-
-#
# AMD Alchemy Db1000 eval board
#
platform-$(CONFIG_MIPS_DB1000) += alchemy/devboards/
@@ -61,7 +54,7 @@ cflags-$(CONFIG_MIPS_DB1550) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1550) += 0xffffffff80100000
#
-# AMD Alchemy Db1200 eval board
+# AMD Alchemy Db1200/Pb1200 eval boards
#
platform-$(CONFIG_MIPS_DB1200) += alchemy/devboards/
cflags-$(CONFIG_MIPS_DB1200) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index f562852..2fbf179 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -5,7 +5,6 @@
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_MIPS_PB1100) += pb1100.o
-obj-$(CONFIG_MIPS_PB1200) += pb1200.o
obj-$(CONFIG_MIPS_PB1500) += pb1500.o
obj-$(CONFIG_MIPS_PB1550) += pb1550.o
obj-$(CONFIG_MIPS_DB1000) += db1x00.o
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
index e2cc5f9..ec481f3 100644
--- a/arch/mips/alchemy/devboards/db1200.c
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -1,5 +1,5 @@
/*
- * DBAu1200 board platform device registration
+ * DBAu1200/PBAu1200 board platform device registration
*
* Copyright (C) 2008-2011 Manuel Lauss
*
@@ -44,10 +44,41 @@
#include "platform.h"
+static const char *board_type_str(void)
+{
+ switch (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI))) {
+ case BCSR_WHOAMI_PB1200_DDR1:
+ case BCSR_WHOAMI_PB1200_DDR2:
+ return "PB1200";
+ case BCSR_WHOAMI_DB1200:
+ return "DB1200";
+ default:
+ return "(unknown)";
+ }
+}
const char *get_system_type(void)
{
- return "DB1200";
+ return board_type_str();
+}
+
+static int __init detect_board(void)
+{
+ int bid;
+
+ /* try the PB1200 first */
+ bcsr_init(PB1200_BCSR_PHYS_ADDR,
+ PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
+ bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+ if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
+ (bid == BCSR_WHOAMI_PB1200_DDR2))
+ return 0;
+
+ /* okay, try the DB1200 then */
+ bcsr_init(DB1200_BCSR_PHYS_ADDR,
+ DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+ bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+ return bid == BCSR_WHOAMI_DB1200 ? 0 : 1;
}
void __init board_setup(void)
@@ -55,12 +86,14 @@ void __init board_setup(void)
unsigned long freq0, clksrc, div, pfc;
unsigned short whoami;
- bcsr_init(DB1200_BCSR_PHYS_ADDR,
- DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+ if (detect_board()) {
+ printk(KERN_ERR "NOT running on a DB1200/PB1200 board!\n");
+ return;
+ }
whoami = bcsr_read(BCSR_WHOAMI);
- printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
- " Board-ID %d Daughtercard ID %d\n",
+ printk(KERN_INFO "Alchemy/AMD/RMI %s Board, CPLD Rev %d"
+ " Board-ID %d Daughtercard ID %d\n", board_type_str(),
(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
/* SMBus/SPI on PSC0, Audio on PSC1 */
@@ -96,7 +129,7 @@ void __init board_setup(void)
static struct mtd_partition db1200_spiflash_parts[] = {
{
- .name = "DB1200 SPI flash",
+ .name = "spi_flash",
.offset = 0,
.size = MTDPART_SIZ_FULL,
},
@@ -376,12 +409,109 @@ static struct led_classdev db1200_mmc_led = {
.brightness_set = db1200_mmcled_set,
};
-static struct au1xmmc_platform_data db1200mmc_platdata = {
- .cd_setup = db1200_mmc_cd_setup,
- .set_power = db1200_mmc_set_power,
- .card_inserted = db1200_mmc_card_inserted,
- .card_readonly = db1200_mmc_card_readonly,
- .led = &db1200_mmc_led,
+/* -- */
+
+static irqreturn_t pb1200_mmc1_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ if (irq == PB1200_SD1_INSERT_INT) {
+ disable_irq_nosync(PB1200_SD1_INSERT_INT);
+ enable_irq(PB1200_SD1_EJECT_INT);
+ } else {
+ disable_irq_nosync(PB1200_SD1_EJECT_INT);
+ enable_irq(PB1200_SD1_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m */
+ mmc_cd = symbol_get(mmc_detect_change);
+ if (mmc_cd) {
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int pb1200_mmc1_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(PB1200_SD1_INSERT_INT, pb1200_mmc1_cd, 0,
+ "sd1_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(PB1200_SD1_EJECT_INT, pb1200_mmc1_cd, 0,
+ "sd1_eject", mmc_host);
+ if (ret) {
+ free_irq(PB1200_SD1_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT)
+ enable_irq(PB1200_SD1_EJECT_INT);
+ else
+ enable_irq(PB1200_SD1_INSERT_INT);
+
+ } else {
+ free_irq(PB1200_SD1_INSERT_INT, mmc_host);
+ free_irq(PB1200_SD1_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void pb1200_mmc1led_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev pb1200_mmc1_led = {
+ .brightness_set = pb1200_mmc1led_set,
+};
+
+static void pb1200_mmc1_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
+}
+
+static int pb1200_mmc1_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
+}
+
+static int pb1200_mmc1_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
+}
+
+
+static struct au1xmmc_platform_data db1200_mmc_platdata[2] = {
+ [0] = {
+ .cd_setup = db1200_mmc_cd_setup,
+ .set_power = db1200_mmc_set_power,
+ .card_inserted = db1200_mmc_card_inserted,
+ .card_readonly = db1200_mmc_card_readonly,
+ .led = &db1200_mmc_led,
+ },
+ [1] = {
+ .cd_setup = pb1200_mmc1_cd_setup,
+ .set_power = pb1200_mmc1_set_power,
+ .card_inserted = pb1200_mmc1_card_inserted,
+ .card_readonly = pb1200_mmc1_card_readonly,
+ .led = &pb1200_mmc1_led,
+ },
};
static struct resource au1200_mmc0_resources[] = {
@@ -415,12 +545,47 @@ static struct platform_device db1200_mmc0_dev = {
.dev = {
.dma_mask = &au1xxx_mmc_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200mmc_platdata,
+ .platform_data = &db1200_mmc_platdata[0],
},
.num_resources = ARRAY_SIZE(au1200_mmc0_resources),
.resource = au1200_mmc0_resources,
};
+static struct resource au1200_mmc1_res[] = {
+ [0] = {
+ .start = AU1100_SD1_PHYS_ADDR,
+ .end = AU1100_SD1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX1,
+ .end = AU1200_DSCR_CMD0_SDMS_TX1,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX1,
+ .end = AU1200_DSCR_CMD0_SDMS_RX1,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc1_dev = {
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200_mmc_platdata[1],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc1_res),
+ .resource = au1200_mmc1_res,
+};
+
/**********************************************************************/
static int db1200fb_panel_index(void)
@@ -598,14 +763,50 @@ static struct platform_device *db1200_devs[] __initdata = {
&db1200_sound_dev,
};
+static struct platform_device *pb1200_devs[] __initdata = {
+ &pb1200_mmc1_dev,
+};
+
+/* Some peripheral base addresses differ on the PB1200 */
+static int __init pb1200_res_fixup(void)
+{
+ /* CPLD Revs earlier than 4 cause problems */
+ if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "PB1200 must be at CPLD rev 4. Please have\n");
+ printk(KERN_ERR "the board updated to latest revisions.\n");
+ printk(KERN_ERR "This software will not work reliably\n");
+ printk(KERN_ERR "on anything older than CPLD rev 4.!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ return 1;
+ }
+
+ db1200_nand_res[0].start = PB1200_NAND_PHYS_ADDR;
+ db1200_nand_res[0].end = PB1200_NAND_PHYS_ADDR + 0xff;
+ db1200_ide_res[0].start = PB1200_IDE_PHYS_ADDR;
+ db1200_ide_res[0].end = PB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1;
+ db1200_eth_res[0].start = PB1200_ETH_PHYS_ADDR;
+ db1200_eth_res[0].end = PB1200_ETH_PHYS_ADDR + 0xff;
+ return 0;
+}
+
static int __init db1200_dev_init(void)
{
unsigned long pfc;
unsigned short sw;
- int swapped;
+ int swapped, bid;
+
+ bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+ if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
+ (bid == BCSR_WHOAMI_PB1200_DDR2)) {
+ if (pb1200_res_fixup())
+ return -ENODEV;
+ }
/* GPIO7 is low-level triggered CPLD cascade */
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQ_TYPE_LEVEL_LOW);
bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
/* insert/eject pairs: one of both is always screaming. To avoid
@@ -626,6 +827,7 @@ static int __init db1200_dev_init(void)
/* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
* S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+ * or S12 on the PB1200.
*/
/* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
@@ -640,7 +842,7 @@ static int __init db1200_dev_init(void)
gpio_request(215, "otg-vbus");
gpio_direction_output(215, 1);
- printk(KERN_INFO "DB1200 device configuration:\n");
+ printk(KERN_INFO "%s device configuration:\n", board_type_str());
sw = bcsr_read(BCSR_SWITCHES);
if (sw & BCSR_SWITCHES_DIP_8) {
@@ -707,6 +909,13 @@ static int __init db1200_dev_init(void)
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
db1x_register_norflash(64 << 20, 2, swapped);
- return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+ platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+
+ /* PB1200 is a DB1200 with a 2nd MMC and Camera connector */
+ if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
+ (bid == BCSR_WHOAMI_PB1200_DDR2))
+ platform_add_devices(pb1200_devs, ARRAY_SIZE(pb1200_devs));
+
+ return 0;
}
device_initcall(db1200_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1200.c b/arch/mips/alchemy/devboards/pb1200.c
deleted file mode 100644
index a2676c9..0000000
--- a/arch/mips/alchemy/devboards/pb1200.c
+++ /dev/null
@@ -1,471 +0,0 @@
-/*
- * Pb1200/DBAu1200 board platform device registration
- *
- * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/smc91x.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1200fb.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-pb1x00/pb1200.h>
-#include <prom.h>
-#include "platform.h"
-
-
-const char *get_system_type(void)
-{
- return "PB1200";
-}
-
-void __init board_setup(void)
-{
- printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
- bcsr_init(PB1200_BCSR_PHYS_ADDR,
- PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
-
-#if 0
- {
- u32 pin_func;
-
- /*
- * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
- }
-#endif
-
-#if defined(CONFIG_I2C_AU1550)
- {
- u32 freq0, clksrc;
- u32 pin_func;
-
- /* Select SMBus in CPLD */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- /* Set GPIOs correctly */
- pin_func |= 2 << 17;
- au_writel(pin_func, SYS_PINFUNC);
- au_sync();
-
- /* The I2C driver depends on 50 MHz clock */
- freq0 = au_readl(SYS_FREQCTRL0);
- au_sync();
- freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
- freq0 |= 3 << SYS_FC_FRDIV1_BIT;
- /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
- freq0 |= SYS_FC_FE1;
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
-
- clksrc = au_readl(SYS_CLKSRC);
- au_sync();
- clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
- /* Bit 22 is EXTCLK0 for PSC0 */
- clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
- au_writel(clksrc, SYS_CLKSRC);
- au_sync();
- }
-#endif
-
- /*
- * The Pb1200 development board uses external MUX for PSC0 to
- * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
- */
-#ifdef CONFIG_I2C_AU1550
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-#endif
- au_sync();
-}
-
-/******************************************************************************/
-
-static int mmc_activity;
-
-static void pb1200mmc0_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc0_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int pb1200mmc0_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void pb1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF) {
- if (++mmc_activity == 1)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- } else {
- if (--mmc_activity == 0)
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
- }
-}
-
-static struct led_classdev pb1200mmc_led = {
- .brightness_set = pb1200_mmcled_set,
-};
-
-static void pb1200mmc1_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc1_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
-}
-
-static int pb1200mmc1_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
-}
-
-static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
- [0] = {
- .set_power = pb1200mmc0_set_power,
- .card_inserted = pb1200mmc0_card_inserted,
- .card_readonly = pb1200mmc0_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
- [1] = {
- .set_power = pb1200mmc1_set_power,
- .card_inserted = pb1200mmc1_card_inserted,
- .card_readonly = pb1200mmc1_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct resource au1200_mmc0_res[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[0],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_res),
- .resource = au1200_mmc0_res,
-};
-
-static struct resource au1200_mmc1_res[] = {
- [0] = {
- .start = AU1100_SD1_PHYS_ADDR,
- .end = AU1100_SD1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX1,
- .end = AU1200_DSCR_CMD0_SDMS_TX1,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX1,
- .end = AU1200_DSCR_CMD0_SDMS_RX1,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc1_dev = {
- .name = "au1xxx-mmc",
- .id = 1,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[1],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc1_res),
- .resource = au1200_mmc1_res,
-};
-
-
-static struct resource ide_resources[] = {
- [0] = {
- .start = IDE_PHYS_ADDR,
- .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = IDE_INT,
- .end = IDE_INT,
- .flags = IORESOURCE_IRQ
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device ide_device = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(ide_resources),
- .resource = ide_resources
-};
-
-static struct smc91x_platdata smc_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91c111_resources[] = {
- [0] = {
- .name = "smc91x-regs",
- .start = SMC91C111_PHYS_ADDR,
- .end = SMC91C111_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = SMC91C111_INT,
- .end = SMC91C111_INT,
- .flags = IORESOURCE_IRQ
- },
-};
-
-static struct platform_device smc91c111_device = {
- .dev = {
- .platform_data = &smc_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smc91c111_resources),
- .resource = smc91c111_resources
-};
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static int pb1200fb_panel_index(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-static int pb1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-static int pb1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
-
-static struct au1200fb_platdata pb1200fb_pd = {
- .panel_index = pb1200fb_panel_index,
- .panel_init = pb1200fb_panel_init,
- .panel_shutdown = pb1200fb_panel_shutdown,
-};
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device pb1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200fb_pd,
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-static struct platform_device *board_platform_devices[] __initdata = {
- &ide_device,
- &smc91c111_device,
- &pb1200_i2c_dev,
- &pb1200_mmc0_dev,
- &pb1200_mmc1_dev,
- &pb1200_lcd_dev,
-};
-
-static int __init board_register_devices(void)
-{
- int swapped;
-
- /* We have a problem with CPLD rev 3. */
- if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
- /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
- /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
-
- return platform_add_devices(board_platform_devices,
- ARRAY_SIZE(board_platform_devices));
-}
-device_initcall(board_register_devices);
diff --git a/arch/mips/configs/pb1200_defconfig b/arch/mips/configs/pb1200_defconfig
deleted file mode 100644
index dcbe270..0000000
--- a/arch/mips/configs/pb1200_defconfig
+++ /dev/null
@@ -1,170 +0,0 @@
-CONFIG_MIPS_ALCHEMY=y
-CONFIG_MIPS_PB1200=y
-CONFIG_KSM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_HZ_100=y
-# CONFIG_SECCOMP is not set
-CONFIG_EXPERIMENTAL=y
-CONFIG_LOCALVERSION="-pb1200"
-CONFIG_KERNEL_LZMA=y
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_TINY_RCU=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_KALLSYMS is not set
-# CONFIG_PCSPKR_PLATFORM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
-CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
-CONFIG_BINFMT_MISC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PLATFORM=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_UB=y
-# CONFIG_MISC_DEVICES is not set
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECS=y
-CONFIG_BLK_DEV_IDECD=y
-CONFIG_IDE_TASK_IOCTL=y
-# CONFIG_IDE_PROC_FS is not set
-CONFIG_BLK_DEV_IDE_AU1XXX=y
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=2
-CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-# CONFIG_I2C_COMPAT is not set
-CONFIG_I2C_CHARDEV=y
-# CONFIG_I2C_HELPER_AUTO is not set
-CONFIG_I2C_AU1550=y
-CONFIG_SPI=y
-CONFIG_SPI_AU1550=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_SENSORS_ADM1025=y
-CONFIG_SENSORS_LM70=y
-CONFIG_FB=y
-CONFIG_FB_AU1200=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x16=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_DYNAMIC_MINORS=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_SPI is not set
-# CONFIG_SND_MIPS is not set
-# CONFIG_SND_USB is not set
-# CONFIG_SND_PCMCIA is not set
-CONFIG_SND_SOC=y
-CONFIG_SND_SOC_AU1XPSC=y
-CONFIG_SND_SOC_DB1200=y
-CONFIG_HIDRAW=y
-CONFIG_USB_HIDDEV=y
-CONFIG_USB=y
-CONFIG_USB_DEBUG=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_ROOT_HUB_TT=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_MMC=y
-# CONFIG_MMC_BLOCK_BOUNCE is not set
-CONFIG_MMC_AU1X=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AU1XXX=y
-CONFIG_EXT2_FS=y
-CONFIG_ISO9660_FS=y
-CONFIG_JOLIET=y
-CONFIG_ZISOFS=y
-CONFIG_UDF_FS=y
-CONFIG_VFAT_FS=y
-# CONFIG_PROC_PAGE_MONITOR is not set
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_JFFS2_RUBIN=y
-CONFIG_SQUASHFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_EFI_PARTITION=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_CODEPAGE_852=y
-CONFIG_NLS_CODEPAGE_1250=y
-CONFIG_NLS_ASCII=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_2=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_STRIP_ASM_SYMS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_FTRACE is not set
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="console=ttyS0,115200"
-CONFIG_DEBUG_ZBOOT=y
-CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
-CONFIG_SECURITYFS=y
diff --git a/arch/mips/include/asm/mach-db1x00/db1200.h b/arch/mips/include/asm/mach-db1x00/db1200.h
index 7a39657..b2a8319 100644
--- a/arch/mips/include/asm/mach-db1x00/db1200.h
+++ b/arch/mips/include/asm/mach-db1x00/db1200.h
@@ -43,15 +43,20 @@
#define BCSR_INT_PC1EJECT 0x0800
#define BCSR_INT_SD0INSERT 0x1000
#define BCSR_INT_SD0EJECT 0x2000
+#define BCSR_INT_SD1INSERT 0x4000
+#define BCSR_INT_SD1EJECT 0x8000
-#define IDE_PHYS_ADDR 0x18800000
#define IDE_REG_SHIFT 5
-#define DB1200_IDE_PHYS_ADDR IDE_PHYS_ADDR
+#define DB1200_IDE_PHYS_ADDR 0x18800000
#define DB1200_IDE_PHYS_LEN (16 << IDE_REG_SHIFT)
#define DB1200_ETH_PHYS_ADDR 0x19000300
#define DB1200_NAND_PHYS_ADDR 0x20000000
+#define PB1200_IDE_PHYS_ADDR 0x0C800000
+#define PB1200_ETH_PHYS_ADDR 0x0D000300
+#define PB1200_NAND_PHYS_ADDR 0x1C000000
+
/*
* External Interrupts for DBAu1200 as of 8/6/2004.
* Bit positions in the CPLD registers can be calculated by taking
@@ -77,6 +82,8 @@ enum external_db1200_ints {
DB1200_PC1_EJECT_INT,
DB1200_SD0_INSERT_INT,
DB1200_SD0_EJECT_INT,
+ PB1200_SD1_INSERT_INT,
+ PB1200_SD1_EJECT_INT,
DB1200_INT_END = DB1200_INT_BEGIN + 15,
};
diff --git a/arch/mips/include/asm/mach-pb1x00/pb1200.h b/arch/mips/include/asm/mach-pb1x00/pb1200.h
deleted file mode 100644
index 374416a..0000000
--- a/arch/mips/include/asm/mach-pb1x00/pb1200.h
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * AMD Alchemy Pb1200 Reference Board
- * Board Registers defines.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#ifndef __ASM_PB1200_H
-#define __ASM_PB1200_H
-
-#include <linux/types.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_psc.h>
-
-#define DBDMA_AC97_TX_CHAN AU1200_DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN AU1200_DSCR_CMD0_PSC1_RX
-#define DBDMA_I2S_TX_CHAN AU1200_DSCR_CMD0_PSC1_TX
-#define DBDMA_I2S_RX_CHAN AU1200_DSCR_CMD0_PSC1_RX
-
-/*
- * SPI and SMB are muxed on the Pb1200 board.
- * Refer to board documentation.
- */
-#define SPI_PSC_BASE AU1550_PSC0_PHYS_ADDR
-#define SMBUS_PSC_BASE AU1550_PSC0_PHYS_ADDR
-/*
- * AC97 and I2S are muxed on the Pb1200 board.
- * Refer to board documentation.
- */
-#define AC97_PSC_BASE AU1550_PSC1_PHYS_ADDR
-#define I2S_PSC_BASE AU1550_PSC1_PHYS_ADDR
-
-
-#define BCSR_SYSTEM_VDDI 0x001F
-#define BCSR_SYSTEM_POWEROFF 0x4000
-#define BCSR_SYSTEM_RESET 0x8000
-
-/* Bit positions for the different interrupt sources */
-#define BCSR_INT_IDE 0x0001
-#define BCSR_INT_ETH 0x0002
-#define BCSR_INT_PC0 0x0004
-#define BCSR_INT_PC0STSCHG 0x0008
-#define BCSR_INT_PC1 0x0010
-#define BCSR_INT_PC1STSCHG 0x0020
-#define BCSR_INT_DC 0x0040
-#define BCSR_INT_FLASHBUSY 0x0080
-#define BCSR_INT_PC0INSERT 0x0100
-#define BCSR_INT_PC0EJECT 0x0200
-#define BCSR_INT_PC1INSERT 0x0400
-#define BCSR_INT_PC1EJECT 0x0800
-#define BCSR_INT_SD0INSERT 0x1000
-#define BCSR_INT_SD0EJECT 0x2000
-#define BCSR_INT_SD1INSERT 0x4000
-#define BCSR_INT_SD1EJECT 0x8000
-
-#define SMC91C111_PHYS_ADDR 0x0D000300
-#define SMC91C111_INT PB1200_ETH_INT
-
-#define IDE_PHYS_ADDR 0x0C800000
-#define IDE_REG_SHIFT 5
-#define IDE_PHYS_LEN (16 << IDE_REG_SHIFT)
-#define IDE_INT PB1200_IDE_INT
-
-#define NAND_PHYS_ADDR 0x1C000000
-
-/*
- * Timing values as described in databook, * ns value stripped of
- * lower 2 bits.
- * These defines are here rather than an Au1200 generic file because
- * the parts chosen on another board may be different and may require
- * different timings.
- */
-#define NAND_T_H (18 >> 2)
-#define NAND_T_PUL (30 >> 2)
-#define NAND_T_SU (30 >> 2)
-#define NAND_T_WH (30 >> 2)
-
-/* Bitfield shift amounts */
-#define NAND_T_H_SHIFT 0
-#define NAND_T_PUL_SHIFT 4
-#define NAND_T_SU_SHIFT 8
-#define NAND_T_WH_SHIFT 12
-
-#define NAND_TIMING (((NAND_T_H & 0xF) << NAND_T_H_SHIFT) | \
- ((NAND_T_PUL & 0xF) << NAND_T_PUL_SHIFT) | \
- ((NAND_T_SU & 0xF) << NAND_T_SU_SHIFT) | \
- ((NAND_T_WH & 0xF) << NAND_T_WH_SHIFT))
-
-/*
- * External Interrupts for Pb1200 as of 8/6/2004.
- * Bit positions in the CPLD registers can be calculated by taking
- * the interrupt define and subtracting the PB1200_INT_BEGIN value.
- *
- * Example: IDE bis pos is = 64 - 64
- * ETH bit pos is = 65 - 64
- */
-enum external_pb1200_ints {
- PB1200_INT_BEGIN = AU1000_MAX_INTR + 1,
-
- PB1200_IDE_INT = PB1200_INT_BEGIN,
- PB1200_ETH_INT,
- PB1200_PC0_INT,
- PB1200_PC0_STSCHG_INT,
- PB1200_PC1_INT,
- PB1200_PC1_STSCHG_INT,
- PB1200_DC_INT,
- PB1200_FLASHBUSY_INT,
- PB1200_PC0_INSERT_INT,
- PB1200_PC0_EJECT_INT,
- PB1200_PC1_INSERT_INT,
- PB1200_PC1_EJECT_INT,
- PB1200_SD0_INSERT_INT,
- PB1200_SD0_EJECT_INT,
- PB1200_SD1_INSERT_INT,
- PB1200_SD1_EJECT_INT,
-
- PB1200_INT_END = PB1200_INT_BEGIN + 15
-};
-
-/* NAND chip select */
-#define NAND_CS 1
-
-#endif /* __ASM_PB1200_H */
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 11/18] MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (9 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 10/18] MIPS: Alchemy: Merge PB1200 support into DB1200 code Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:53 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 12/18] MIPS: Alchemy: MMC for DB1100 Manuel Lauss
` (6 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Kconfig | 21 +--
arch/mips/alchemy/Platform | 16 +--
arch/mips/alchemy/devboards/Makefile | 4 +-
arch/mips/alchemy/devboards/db1000.c | 267 ++++++++++++++++++++++++
arch/mips/alchemy/devboards/db1x00.c | 256 -----------------------
arch/mips/alchemy/devboards/prom.c | 4 +-
arch/mips/configs/db1000_defconfig | 369 ++++++++++++++++++++++++++++------
arch/mips/configs/db1100_defconfig | 122 -----------
arch/mips/configs/db1500_defconfig | 128 ------------
drivers/net/irda/au1k_ir.c | 10 +-
drivers/video/au1100fb.c | 12 -
11 files changed, 584 insertions(+), 625 deletions(-)
create mode 100644 arch/mips/alchemy/devboards/db1000.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00.c
delete mode 100644 arch/mips/configs/db1100_defconfig
delete mode 100644 arch/mips/configs/db1500_defconfig
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index e1b3be7..0faaab2 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -27,17 +27,12 @@ config MIPS_MTX1
select SYS_HAS_EARLY_PRINTK
config MIPS_DB1000
- bool "Alchemy DB1000 board"
+ bool "Alchemy DB1000/DB1500/DB1100 boards"
select ALCHEMY_GPIOINT_AU1000
select DMA_NONCOHERENT
select HW_HAS_PCI
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
-config MIPS_DB1100
- bool "Alchemy DB1100 board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
+ select MIPS_DISABLE_OBSOLETE_IDE
+ select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
@@ -57,16 +52,6 @@ config MIPS_DB1300
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_DB1500
- bool "Alchemy DB1500 board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select MIPS_DISABLE_OBSOLETE_IDE
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_DB1550
bool "Alchemy DB1550 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index bbdcc15..33f80e8 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -26,27 +26,13 @@ cflags-$(CONFIG_MIPS_PB1550) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1550) += 0xffffffff80100000
#
-# AMD Alchemy Db1000 eval board
+# AMD Alchemy Db1000/Db1500/Db1100 eval boards
#
platform-$(CONFIG_MIPS_DB1000) += alchemy/devboards/
cflags-$(CONFIG_MIPS_DB1000) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1000) += 0xffffffff80100000
#
-# AMD Alchemy Db1100 eval board
-#
-platform-$(CONFIG_MIPS_DB1100) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_DB1100) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_DB1100) += 0xffffffff80100000
-
-#
-# AMD Alchemy Db1500 eval board
-#
-platform-$(CONFIG_MIPS_DB1500) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_DB1500) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_DB1500) += 0xffffffff80100000
-
-#
# AMD Alchemy Db1550 eval board
#
platform-$(CONFIG_MIPS_DB1550) += alchemy/devboards/
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 2fbf179..3c37fb3 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -7,9 +7,7 @@ obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_MIPS_PB1100) += pb1100.o
obj-$(CONFIG_MIPS_PB1500) += pb1500.o
obj-$(CONFIG_MIPS_PB1550) += pb1550.o
-obj-$(CONFIG_MIPS_DB1000) += db1x00.o
-obj-$(CONFIG_MIPS_DB1100) += db1x00.o
+obj-$(CONFIG_MIPS_DB1000) += db1000.o
obj-$(CONFIG_MIPS_DB1200) += db1200.o
obj-$(CONFIG_MIPS_DB1300) += db1300.o
-obj-$(CONFIG_MIPS_DB1500) += db1x00.o
obj-$(CONFIG_MIPS_DB1550) += db1550.o
diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c
new file mode 100644
index 0000000..57ed5f1
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1000.c
@@ -0,0 +1,267 @@
+/*
+ * DBAu1000/1500/1100 board support
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1000_dma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
+#include <prom.h>
+#include "platform.h"
+
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+struct pci_dev;
+
+static const char *board_type_str(void)
+{
+ switch (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI))) {
+ case BCSR_WHOAMI_DB1000:
+ return "DB1000";
+ case BCSR_WHOAMI_DB1500:
+ return "DB1500";
+ case BCSR_WHOAMI_DB1100:
+ return "DB1100";
+ default:
+ return "(unknown)";
+ }
+}
+
+const char *get_system_type(void)
+{
+ return board_type_str();
+}
+
+void __init board_setup(void)
+{
+ /* initialize board register space */
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ printk(KERN_INFO "AMD Alchemy %s Board\n", board_type_str());
+
+#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
+ {
+ u32 pin_func;
+
+ /* Set IRFIRSEL instead of GPIO15 */
+ pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
+ au_writel(pin_func, SYS_PINFUNC);
+ /* Power off until the driver is in use */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
+ BCSR_RESETS_IRDA_MODE_OFF);
+ }
+#endif
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ /* Enable GPIO[31:0] inputs */
+ alchemy_gpio1_input_enable();
+}
+
+
+static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata db1500_pci_pd = {
+ .board_map_irq = db1500_map_pci_irq,
+};
+
+static struct platform_device db1500_pci_host_dev = {
+ .dev.platform_data = &db1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init db1500_pci_init(void)
+{
+ if (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) == BCSR_WHOAMI_DB1500)
+ return platform_device_register(&db1500_pci_host_dev);
+ return 0;
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(db1500_pci_init);
+
+
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+
+static struct resource alchemy_ac97c_res[] = {
+ [0] = {
+ .start = AU1000_AC97_PHYS_ADDR,
+ .end = AU1000_AC97_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DMA_ID_AC97C_TX,
+ .end = DMA_ID_AC97C_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = DMA_ID_AC97C_RX,
+ .end = DMA_ID_AC97C_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device alchemy_ac97c_dev = {
+ .name = "alchemy-ac97c",
+ .id = -1,
+ .resource = alchemy_ac97c_res,
+ .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
+};
+
+static struct platform_device alchemy_ac97c_dma_dev = {
+ .name = "alchemy-pcm-dma",
+ .id = 0,
+};
+
+static struct platform_device db1x00_codec_dev = {
+ .name = "ac97-codec",
+ .id = -1,
+};
+
+static struct platform_device db1x00_audio_dev = {
+ .name = "db1000-audio",
+};
+
+static struct platform_device *db1x00_devs[] = {
+ &db1x00_codec_dev,
+ &alchemy_ac97c_dma_dev,
+ &alchemy_ac97c_dev,
+ &db1x00_audio_dev,
+};
+
+static struct platform_device *db1100_devs[] = {
+ &au1100_lcd_device,
+};
+
+static int __init db1000_dev_init(void)
+{
+ int board = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+ int c0, c1, d0, d1, s0, s1;
+
+ if (board == BCSR_WHOAMI_DB1500) {
+ c0 = AU1500_GPIO2_INT;
+ c1 = AU1500_GPIO5_INT;
+ d0 = AU1500_GPIO0_INT;
+ d1 = AU1500_GPIO3_INT;
+ s0 = AU1500_GPIO1_INT;
+ s1 = AU1500_GPIO4_INT;
+ } else if (board == BCSR_WHOAMI_DB1100) {
+ c0 = AU1100_GPIO2_INT;
+ c1 = AU1100_GPIO5_INT;
+ d0 = AU1100_GPIO0_INT;
+ d1 = AU1100_GPIO3_INT;
+ s0 = AU1100_GPIO1_INT;
+ s1 = AU1100_GPIO4_INT;
+ platform_add_devices(db1100_devs, ARRAY_SIZE(db1100_devs));
+ } else if (board == BCSR_WHOAMI_DB1000) {
+ c0 = AU1000_GPIO2_INT;
+ c1 = AU1000_GPIO5_INT;
+ d0 = AU1000_GPIO0_INT;
+ d1 = AU1000_GPIO3_INT;
+ s0 = AU1000_GPIO1_INT;
+ s1 = AU1000_GPIO4_INT;
+ } else
+ return 0; /* unknown board, no further dev setup to do */
+
+ irq_set_irq_type(d0, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(d1, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(c0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(c1, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(s0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(s1, IRQ_TYPE_LEVEL_LOW);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ c0, d0, /*s0*/0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ c1, d1, /*s1*/0, 0, 1);
+
+ platform_add_devices(db1x00_devs, ARRAY_SIZE(db1x00_devs));
+ db1x_register_norflash(32 << 20, 4 /* 32bit */, F_SWAPPED);
+ return 0;
+}
+device_initcall(db1000_dev_init);
diff --git a/arch/mips/alchemy/devboards/db1x00.c b/arch/mips/alchemy/devboards/db1x00.c
deleted file mode 100644
index 589ae24..0000000
--- a/arch/mips/alchemy/devboards/db1x00.c
+++ /dev/null
@@ -1,256 +0,0 @@
-/*
- * DBAu1000/1500/1100 board support
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/pm.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1000_dma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/reboot.h>
-#include <prom.h>
-#include "platform.h"
-
-struct pci_dev;
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1x00";
-}
-
-void __init board_setup(void)
-{
-#ifdef CONFIG_MIPS_DB1000
- printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
- printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
- printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
-#endif
- /* initialize board register space */
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
-#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
- {
- u32 pin_func;
-
- /* Set IRFIRSEL instead of GPIO15 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
- au_writel(pin_func, SYS_PINFUNC);
- /* Power off until the driver is in use */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
- BCSR_RESETS_IRDA_MODE_OFF);
- }
-#endif
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- /* Enable GPIO[31:0] inputs */
- alchemy_gpio1_input_enable();
-}
-
-/* DB1xxx PCMCIA interrupt sources:
- * CD0/1 GPIO0/3
- * STSCHG0/1 GPIO1/4
- * CARD0/1 GPIO2/5
- */
-
-#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
-
-#if defined(CONFIG_MIPS_DB1000)
-#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1100)
-#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1500)
-#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
-
-static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata db1500_pci_pd = {
- .board_map_irq = db1500_map_pci_irq,
-};
-
-static struct platform_device db1500_pci_host_dev = {
- .dev.platform_data = &db1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init db1500_pci_init(void)
-{
- return platform_device_register(&db1500_pci_host_dev);
-}
-/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
-arch_initcall(db1500_pci_init);
-#endif
-
-#ifdef CONFIG_MIPS_DB1100
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-#endif
-
-static struct resource alchemy_ac97c_res[] = {
- [0] = {
- .start = AU1000_AC97_PHYS_ADDR,
- .end = AU1000_AC97_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMA_ID_AC97C_TX,
- .end = DMA_ID_AC97C_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMA_ID_AC97C_RX,
- .end = DMA_ID_AC97C_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device alchemy_ac97c_dev = {
- .name = "alchemy-ac97c",
- .id = -1,
- .resource = alchemy_ac97c_res,
- .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
-};
-
-static struct platform_device alchemy_ac97c_dma_dev = {
- .name = "alchemy-pcm-dma",
- .id = 0,
-};
-
-static struct platform_device db1x00_codec_dev = {
- .name = "ac97-codec",
- .id = -1,
-};
-
-static struct platform_device db1x00_audio_dev = {
- .name = "db1000-audio",
-};
-
-static int __init db1xxx_dev_init(void)
-{
- irq_set_irq_type(DB1XXX_PCMCIA_CD0, IRQ_TYPE_EDGE_BOTH);
- irq_set_irq_type(DB1XXX_PCMCIA_CD1, IRQ_TYPE_EDGE_BOTH);
- irq_set_irq_type(DB1XXX_PCMCIA_CARD0, IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(DB1XXX_PCMCIA_CARD1, IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(DB1XXX_PCMCIA_STSCHG0, IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(DB1XXX_PCMCIA_STSCHG1, IRQ_TYPE_LEVEL_LOW);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
- /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
- /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
-#ifdef CONFIG_MIPS_DB1100
- platform_device_register(&au1100_lcd_device);
-#endif
- platform_device_register(&db1x00_codec_dev);
- platform_device_register(&alchemy_ac97c_dma_dev);
- platform_device_register(&alchemy_ac97c_dev);
- platform_device_register(&db1x00_audio_dev);
-
- db1x_register_norflash(32 << 20, 4 /* 32bit */, F_SWAPPED);
- return 0;
-}
-device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index 3a73f96..93a2210 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -34,8 +34,8 @@
#include <prom.h>
#if defined(CONFIG_MIPS_DB1000) || \
- defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
- defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500)
+ defined(CONFIG_MIPS_PB1100) || \
+ defined(CONFIG_MIPS_PB1500)
#define ALCHEMY_BOARD_DEFAULT_MEMSIZE 0x04000000
#else /* Au1550/Au1200-based develboards */
diff --git a/arch/mips/configs/db1000_defconfig b/arch/mips/configs/db1000_defconfig
index 4044c9e..17a36c1 100644
--- a/arch/mips/configs/db1000_defconfig
+++ b/arch/mips/configs/db1000_defconfig
@@ -1,118 +1,359 @@
+CONFIG_MIPS=y
CONFIG_MIPS_ALCHEMY=y
+CONFIG_MIPS_DB1000=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_HZ_100=y
-# CONFIG_SECCOMP is not set
+CONFIG_HZ=100
+CONFIG_PREEMPT_NONE=y
CONFIG_EXPERIMENTAL=y
-CONFIG_LOCALVERSION="-db1000"
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
+CONFIG_LOCALVERSION="-db1x00"
+CONFIG_LOCALVERSION_AUTO=y
CONFIG_KERNEL_LZMA=y
+CONFIG_DEFAULT_HOSTNAME="db1x00"
+CONFIG_SWAP=y
CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_FHANDLE=y
+CONFIG_AUDIT=y
CONFIG_TINY_RCU=y
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+CONFIG_USER_NS=y
+CONFIG_PID_NS=y
+CONFIG_NET_NS=y
+CONFIG_SYSCTL=y
CONFIG_EXPERT=y
-# CONFIG_KALLSYMS is not set
-# CONFIG_PCSPKR_PLATFORM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_EMBEDDED=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PCI_QUIRKS=y
CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
+CONFIG_SLABINFO=y
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+CONFIG_BLK_DEV_BSG=y
+CONFIG_BLK_DEV_BSGLIB=y
+CONFIG_IOSCHED_NOOP=y
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_FREEZER=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
CONFIG_PCCARD=y
+CONFIG_PCMCIA=y
+CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
-CONFIG_PM=y
+CONFIG_BINFMT_ELF=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_PM_SLEEP=y
CONFIG_PM_RUNTIME=y
+CONFIG_PM=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
+CONFIG_XFRM=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_NET_IPIP=y
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_LRO=y
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+CONFIG_IPV6=y
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_STP=y
+CONFIG_GARP=y
+CONFIG_BRIDGE=y
+CONFIG_BRIDGE_IGMP_SNOOPING=y
+CONFIG_VLAN_8021Q=y
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_LLC=y
+CONFIG_LLC2=y
+CONFIG_DNS_RESOLVER=y
+CONFIG_BT=y
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=y
+CONFIG_BT_HCIBTUSB=y
+CONFIG_UEVENT_HELPER_PATH=""
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+CONFIG_MTD_CFI_GEOMETRY=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI_I4=y
+CONFIG_MTD_CFI_I8=y
+CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_UTIL=y
CONFIG_MTD_PHYSMAP=y
-# CONFIG_MISC_DEVICES is not set
+CONFIG_SCSI_MOD=y
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+CONFIG_SCSI_PROC_FS=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_MULTI_LUN=y
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_ATA=y
+CONFIG_ATA_VERBOSE_ERROR=y
+CONFIG_ATA_SFF=y
+CONFIG_ATA_BMDMA=y
+CONFIG_PATA_HPT37X=y
+CONFIG_PATA_PCMCIA=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_DM=y
+CONFIG_FIREWIRE=y
+CONFIG_FIREWIRE_OHCI=y
+CONFIG_FIREWIRE_OHCI_DEBUG=y
+CONFIG_FIREWIRE_NET=y
CONFIG_NETDEVICES=y
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-CONFIG_BROADCOM_PHY=y
-CONFIG_ICPLUS_PHY=y
-CONFIG_REALTEK_PHY=y
-CONFIG_NATIONAL_PHY=y
-CONFIG_STE10XP=y
-CONFIG_LSI_ET1011C_PHY=y
-CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+CONFIG_PHYLIB=y
+CONFIG_NET_ETHERNET=y
CONFIG_MIPS_AU1X00_ENET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_NET_PCMCIA=y
+CONFIG_PCMCIA_3C589=y
+CONFIG_PCMCIA_PCNET=y
+CONFIG_PPP=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=y
+CONFIG_PPP_SYNC_TTY=y
+CONFIG_PPP_DEFLATE=y
+CONFIG_PPP_BSDCOMP=y
+CONFIG_PPP_MPPE=y
+CONFIG_PPPOE=y
+CONFIG_INPUT=y
CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
+CONFIG_DEVKMEM=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-# CONFIG_VGA_CONSOLE is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_TTY_PRINTK=y
+CONFIG_DEVPORT=y
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_FB=y
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+CONFIG_FB_AU1100=y
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x16=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+CONFIG_SND_SEQUENCER=y
+CONFIG_SND_HRTIMER=y
+CONFIG_SND_SEQ_HRTIMER_DEFAULT=y
+CONFIG_SND_DYNAMIC_MINORS=y
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_AC97_BUS=y
+CONFIG_SND_SOC_AU1XAUDIO=y
+CONFIG_SND_SOC_AU1XAC97C=y
+CONFIG_SND_SOC_DB1000=y
+CONFIG_SND_SOC_AC97_CODEC=y
+CONFIG_AC97_BUS=y
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+CONFIG_HIDRAW=y
+CONFIG_USB_HID=y
+CONFIG_USB_SUPPORT=y
CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_SUSPEND=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_DRV_AU1XXX=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-# CONFIG_EXT3_FS_XATTR is not set
-# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_USE_FOR_EXT23=y
+CONFIG_EXT4_FS_XATTR=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_JBD2=y
+CONFIG_FS_MBCACHE=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_EXPORTFS=y
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_GENERIC_ACL=y
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
CONFIG_TMPFS=y
-CONFIG_CRAMFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_FS_POSIX_ACL=y
+CONFIG_JFFS2_FS_SECURITY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_JFFS2_CMODE_PRIORITY=y
CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_ZLIB=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_PNFS_FILE_LAYOUT=y
+CONFIG_PNFS_BLOCK=y
CONFIG_ROOT_NFS=y
+CONFIG_NFS_USE_KERNEL_DNS=y
+CONFIG_NFS_USE_NEW_IDMAPPER=y
+CONFIG_NFSD=y
+CONFIG_NFSD_V2_ACL=y
+CONFIG_NFSD_V3=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_SUNRPC_BACKCHANNEL=y
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_15=y
CONFIG_NLS_UTF8=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_STRIP_ASM_SYMS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_FTRACE is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="noirqdebug rootwait root=/dev/sda1 rootfstype=ext4 console=ttyS0,115200 video=au1100fb:panel:CRT_800x600_16"
CONFIG_DEBUG_ZBOOT=y
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
+CONFIG_SECURITYFS=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP2=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ANSI_CPRNG=y
+CONFIG_BITREVERSE=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC16=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC32=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_XZ_DEC=y
diff --git a/arch/mips/configs/db1100_defconfig b/arch/mips/configs/db1100_defconfig
deleted file mode 100644
index c6b4993..0000000
--- a/arch/mips/configs/db1100_defconfig
+++ /dev/null
@@ -1,122 +0,0 @@
-CONFIG_MIPS_ALCHEMY=y
-CONFIG_MIPS_DB1100=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_HZ_100=y
-# CONFIG_SECCOMP is not set
-CONFIG_EXPERIMENTAL=y
-CONFIG_LOCALVERSION="-db1100"
-CONFIG_KERNEL_LZMA=y
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_TINY_RCU=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_KALLSYMS is not set
-# CONFIG_PCSPKR_PLATFORM is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
-CONFIG_PM=y
-CONFIG_PM_RUNTIME=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_PHYSMAP=y
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-CONFIG_IDE=y
-CONFIG_IDE_TASK_IOCTL=y
-CONFIG_NETDEVICES=y
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-CONFIG_BROADCOM_PHY=y
-CONFIG_ICPLUS_PHY=y
-CONFIG_REALTEK_PHY=y
-CONFIG_NATIONAL_PHY=y
-CONFIG_STE10XP=y
-CONFIG_LSI_ET1011C_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_MIPS_AU1X00_ENET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-CONFIG_FB=y
-CONFIG_FB_AU1100=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x16=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AU1XXX=y
-CONFIG_EXT2_FS=y
-# CONFIG_PROC_PAGE_MONITOR is not set
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_JFFS2_FS_XATTR=y
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_JFFS2_RUBIN=y
-CONFIG_SQUASHFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_STRIP_ASM_SYMS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_ZBOOT=y
-CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
-CONFIG_SECURITYFS=y
diff --git a/arch/mips/configs/db1500_defconfig b/arch/mips/configs/db1500_defconfig
deleted file mode 100644
index b6e21c7..0000000
--- a/arch/mips/configs/db1500_defconfig
+++ /dev/null
@@ -1,128 +0,0 @@
-CONFIG_MIPS_ALCHEMY=y
-CONFIG_MIPS_DB1500=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_HZ_100=y
-# CONFIG_SECCOMP is not set
-CONFIG_EXPERIMENTAL=y
-CONFIG_LOCALVERSION="-db1500"
-CONFIG_KERNEL_LZMA=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-# CONFIG_KALLSYMS is not set
-# CONFIG_PCSPKR_PLATFORM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_PCI=y
-CONFIG_PCCARD=y
-# CONFIG_CARDBUS is not set
-CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
-CONFIG_PM=y
-CONFIG_PM_RUNTIME=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_PHYSMAP=y
-# CONFIG_MISC_DEVICES is not set
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECS=y
-# CONFIG_IDEPCI_PCIBUS_ORDER is not set
-CONFIG_BLK_DEV_HPT366=y
-CONFIG_NETDEVICES=y
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-CONFIG_BROADCOM_PHY=y
-CONFIG_ICPLUS_PHY=y
-CONFIG_REALTEK_PHY=y
-CONFIG_NATIONAL_PHY=y
-CONFIG_STE10XP=y
-CONFIG_LSI_ET1011C_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_MIPS_AU1X00_ENET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_SERIAL_8250_PCI is not set
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-# CONFIG_VGA_ARB is not set
-# CONFIG_VGA_CONSOLE is not set
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AU1XXX=y
-CONFIG_EXT2_FS=y
-# CONFIG_PROC_PAGE_MONITOR is not set
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_JFFS2_FS_XATTR=y
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_JFFS2_RUBIN=y
-CONFIG_SQUASHFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_CODEPAGE_1250=y
-CONFIG_NLS_ASCII=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-CONFIG_STRIP_ASM_SYMS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_ZBOOT=y
-CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
-CONFIG_SECURITYFS=y
diff --git a/drivers/net/irda/au1k_ir.c b/drivers/net/irda/au1k_ir.c
index d1a77ef..670bb05 100644
--- a/drivers/net/irda/au1k_ir.c
+++ b/drivers/net/irda/au1k_ir.c
@@ -32,7 +32,7 @@
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/au1000.h>
-#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
+#if defined(CONFIG_MIPS_DB1000)
#include <asm/mach-db1x00/bcsr.h>
#else
#error au1k_ir: unsupported board
@@ -274,7 +274,7 @@ static int au1k_irda_net_init(struct net_device *dev)
aup->tx_db_inuse[i] = pDB;
}
-#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
+#if defined(CONFIG_MIPS_DB1000)
/* power on */
bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
BCSR_RESETS_IRDA_MODE_FULL);
@@ -662,7 +662,7 @@ au1k_irda_set_speed(struct net_device *dev, int speed)
u32 control;
int ret = 0, timeout = 10, i;
volatile ring_dest_t *ptxd;
-#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
+#if defined(CONFIG_MIPS_DB1000)
unsigned long irda_resets;
#endif
@@ -711,14 +711,14 @@ au1k_irda_set_speed(struct net_device *dev, int speed)
}
if (speed == 4000000) {
-#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
+#if defined(CONFIG_MIPS_DB1000)
bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_FIR_SEL);
#else /* Pb1000 and Pb1100 */
writel(1<<13, CPLD_AUX1);
#endif
}
else {
-#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
+#if defined(CONFIG_MIPS_DB1000)
bcsr_mod(BCSR_RESETS, BCSR_RESETS_FIR_SEL, 0);
#else /* Pb1000 and Pb1100 */
writel(readl(CPLD_AUX1) & ~(1<<13), CPLD_AUX1);
diff --git a/drivers/video/au1100fb.c b/drivers/video/au1100fb.c
index 649cb35..de9da67 100644
--- a/drivers/video/au1100fb.c
+++ b/drivers/video/au1100fb.c
@@ -60,18 +60,6 @@
#include "au1100fb.h"
-/*
- * Sanity check. If this is a new Au1100 based board, search for
- * the PB1100 ifdefs to make sure you modify the code accordingly.
- */
-#if defined(CONFIG_MIPS_PB1100)
- #include <asm/mach-pb1x00/pb1100.h>
-#elif defined(CONFIG_MIPS_DB1100)
- #include <asm/mach-db1x00/db1x00.h>
-#else
- #error "Unknown Au1100 board, Au1100 FB driver not supported"
-#endif
-
#define DRIVER_NAME "au1100fb"
#define DRIVER_DESC "LCD controller driver for AU1100 processors"
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 12/18] MIPS: Alchemy: MMC for DB1100
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (10 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 11/18] MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100 Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:53 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 13/18] MIPS: Alchemy: add RTC device to all devboards Manuel Lauss
` (5 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
This patch hooks up the 2 MMC sockets on the DB1100 board.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/devboards/db1000.c | 201 ++++++++++++++++++++++++++++++++++
1 files changed, 201 insertions(+), 0 deletions(-)
diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c
index 57ed5f1..e531bfa 100644
--- a/arch/mips/alchemy/devboards/db1000.c
+++ b/arch/mips/alchemy/devboards/db1000.c
@@ -23,10 +23,13 @@
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1000_dma.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
#include <asm/mach-db1x00/bcsr.h>
#include <asm/reboot.h>
#include <prom.h>
@@ -194,6 +197,198 @@ static struct platform_device db1x00_audio_dev = {
.name = "db1000-audio",
};
+/******************************************************************************/
+
+static irqreturn_t db1100_mmc_cd(int irq, void *ptr)
+{
+ void (*mmc_cd)(struct mmc_host *, unsigned long);
+ /* link against CONFIG_MMC=m */
+ mmc_cd = symbol_get(mmc_detect_change);
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+
+ return IRQ_HANDLED;
+}
+
+static int db1100_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret = 0;
+
+ if (en) {
+ irq_set_irq_type(AU1100_GPIO19_INT, IRQ_TYPE_EDGE_BOTH);
+ ret = request_irq(AU1100_GPIO19_INT, db1100_mmc_cd, 0,
+ "sd0_cd", mmc_host);
+ } else
+ free_irq(AU1100_GPIO19_INT, mmc_host);
+ return ret;
+}
+
+static int db1100_mmc1_cd_setup(void *mmc_host, int en)
+{
+ int ret = 0;
+
+ if (en) {
+ irq_set_irq_type(AU1100_GPIO20_INT, IRQ_TYPE_EDGE_BOTH);
+ ret = request_irq(AU1100_GPIO20_INT, db1100_mmc_cd, 0,
+ "sd1_cd", mmc_host);
+ } else
+ free_irq(AU1100_GPIO20_INT, mmc_host);
+ return ret;
+}
+
+static int db1100_mmc_card_readonly(void *mmc_host)
+{
+ /* testing suggests that this bit is inverted */
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 0 : 1;
+}
+
+static int db1100_mmc_card_inserted(void *mmc_host)
+{
+ return !alchemy_gpio_get_value(19);
+}
+
+static void db1100_mmc_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static void db1100_mmcled_set(struct led_classdev *led, enum led_brightness b)
+{
+ if (b != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1100_mmc_led = {
+ .brightness_set = db1100_mmcled_set,
+};
+
+static int db1100_mmc1_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_BOARD) & BCSR_BOARD_SD1WP) ? 1 : 0;
+}
+
+static int db1100_mmc1_card_inserted(void *mmc_host)
+{
+ return !alchemy_gpio_get_value(20);
+}
+
+static void db1100_mmc1_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
+}
+
+static void db1100_mmc1led_set(struct led_classdev *led, enum led_brightness b)
+{
+ if (b != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev db1100_mmc1_led = {
+ .brightness_set = db1100_mmc1led_set,
+};
+
+static struct au1xmmc_platform_data db1100_mmc_platdata[2] = {
+ [0] = {
+ .cd_setup = db1100_mmc_cd_setup,
+ .set_power = db1100_mmc_set_power,
+ .card_inserted = db1100_mmc_card_inserted,
+ .card_readonly = db1100_mmc_card_readonly,
+ .led = &db1100_mmc_led,
+ },
+ [1] = {
+ .cd_setup = db1100_mmc1_cd_setup,
+ .set_power = db1100_mmc1_set_power,
+ .card_inserted = db1100_mmc1_card_inserted,
+ .card_readonly = db1100_mmc1_card_readonly,
+ .led = &db1100_mmc1_led,
+ },
+};
+
+static struct resource au1100_mmc0_resources[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_SD_INT,
+ .end = AU1100_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = DMA_ID_SD0_TX,
+ .end = DMA_ID_SD0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = DMA_ID_SD0_RX,
+ .end = DMA_ID_SD0_RX,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1100_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1100_mmc_platdata[0],
+ },
+ .num_resources = ARRAY_SIZE(au1100_mmc0_resources),
+ .resource = au1100_mmc0_resources,
+};
+
+static struct resource au1100_mmc1_res[] = {
+ [0] = {
+ .start = AU1100_SD1_PHYS_ADDR,
+ .end = AU1100_SD1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_SD_INT,
+ .end = AU1100_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = DMA_ID_SD1_TX,
+ .end = DMA_ID_SD1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = DMA_ID_SD1_RX,
+ .end = DMA_ID_SD1_RX,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device db1100_mmc1_dev = {
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1100_mmc_platdata[1],
+ },
+ .num_resources = ARRAY_SIZE(au1100_mmc1_res),
+ .resource = au1100_mmc1_res,
+};
+
+
static struct platform_device *db1x00_devs[] = {
&db1x00_codec_dev,
&alchemy_ac97c_dma_dev,
@@ -203,6 +398,8 @@ static struct platform_device *db1x00_devs[] = {
static struct platform_device *db1100_devs[] = {
&au1100_lcd_device,
+ &db1100_mmc0_dev,
+ &db1100_mmc1_dev,
};
static int __init db1000_dev_init(void)
@@ -224,6 +421,10 @@ static int __init db1000_dev_init(void)
d1 = AU1100_GPIO3_INT;
s0 = AU1100_GPIO1_INT;
s1 = AU1100_GPIO4_INT;
+
+ gpio_direction_input(19); /* sd0 cd# */
+ gpio_direction_input(20); /* sd1 cd# */
+
platform_add_devices(db1100_devs, ARRAY_SIZE(db1100_devs));
} else if (board == BCSR_WHOAMI_DB1000) {
c0 = AU1000_GPIO2_INT;
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 13/18] MIPS: Alchemy: add RTC device to all devboards
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (11 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 12/18] MIPS: Alchemy: MMC for DB1100 Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:53 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 14/18] MTD: nand: make au1550nd.c a platform_driver Manuel Lauss
` (4 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
All Devboards can use the 32kHz counter as a RTC device.
Also delete the custom CMOS RTC header, which can be used for the
DS1693 on the PB1500. But since it doesn't have a buffer battery
it is as useful as the on-chip RTC which I prefer.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/devboards/db1200.c | 8 -----
arch/mips/alchemy/devboards/db1300.c | 8 -----
arch/mips/alchemy/devboards/db1550.c | 8 -----
arch/mips/alchemy/devboards/platform.c | 13 +++++++-
arch/mips/include/asm/mach-pb1x00/mc146818rtc.h | 34 -----------------------
5 files changed, 11 insertions(+), 60 deletions(-)
delete mode 100644 arch/mips/include/asm/mach-pb1x00/mc146818rtc.h
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
index ec481f3..1181241 100644
--- a/arch/mips/alchemy/devboards/db1200.c
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -312,13 +312,6 @@ static struct platform_device db1200_ide_dev = {
/**********************************************************************/
-static struct platform_device db1200_rtc_dev = {
- .name = "rtc-au1xxx",
- .id = -1,
-};
-
-/**********************************************************************/
-
/* SD carddetects: they're supposed to be edge-triggered, but ack
* doesn't seem to work (CPLD Rev 2). Instead, the screaming one
* is disabled and its counterpart enabled. The 500ms timeout is
@@ -755,7 +748,6 @@ static struct platform_device *db1200_devs[] __initdata = {
&db1200_mmc0_dev,
&au1200_lcd_dev,
&db1200_eth_dev,
- &db1200_rtc_dev,
&db1200_nand_dev,
&db1200_audiodma_dev,
&db1200_audio_dev,
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
index d1a7344..23fd4ff 100644
--- a/arch/mips/alchemy/devboards/db1300.c
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -385,13 +385,6 @@ static struct platform_device db1300_5waysw_dev = {
/**********************************************************************/
-static struct platform_device db1300_rtc_dev = {
- .name = "rtc-au1xxx",
- .id = -1,
-};
-
-/**********************************************************************/
-
static struct pata_platform_info db1300_ide_info = {
.ioport_shift = DB1300_IDE_REG_SHIFT,
};
@@ -696,7 +689,6 @@ static struct platform_device *db1300_dev[] __initdata = {
&db1300_eth_dev,
&db1300_i2c_dev,
&db1300_5waysw_dev,
- &db1300_rtc_dev,
&db1300_nand_dev,
&db1300_ide_dev,
&db1300_sd0_dev,
diff --git a/arch/mips/alchemy/devboards/db1550.c b/arch/mips/alchemy/devboards/db1550.c
index a4755b0..6815d07 100644
--- a/arch/mips/alchemy/devboards/db1550.c
+++ b/arch/mips/alchemy/devboards/db1550.c
@@ -372,13 +372,6 @@ static struct platform_device db1550_sndi2s_dev = {
/**********************************************************************/
-static struct platform_device db1550_rtc_dev = {
- .name = "rtc-au1xxx",
- .id = -1,
-};
-
-/**********************************************************************/
-
static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
{
if ((slot < 11) || (slot > 13) || pin == 0)
@@ -427,7 +420,6 @@ static struct platform_device db1550_pci_host_dev = {
/**********************************************************************/
static struct platform_device *db1550_devs[] __initdata = {
- &db1550_rtc_dev,
&db1550_nand_dev,
&db1550_i2c_dev,
&db1550_ac97_dev,
diff --git a/arch/mips/alchemy/devboards/platform.c b/arch/mips/alchemy/devboards/platform.c
index 49a4b32..621f70a 100644
--- a/arch/mips/alchemy/devboards/platform.c
+++ b/arch/mips/alchemy/devboards/platform.c
@@ -13,6 +13,13 @@
#include <asm/reboot.h>
#include <asm/mach-db1x00/bcsr.h>
+
+static struct platform_device db1x00_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+
static void db1x_power_off(void)
{
bcsr_write(BCSR_RESETS, 0);
@@ -25,7 +32,7 @@ static void db1x_reset(char *c)
bcsr_write(BCSR_SYSTEM, 0);
}
-static int __init db1x_poweroff_setup(void)
+static int __init db1x_late_setup(void)
{
if (!pm_power_off)
pm_power_off = db1x_power_off;
@@ -34,9 +41,11 @@ static int __init db1x_poweroff_setup(void)
if (!_machine_restart)
_machine_restart = db1x_reset;
+ platform_device_register(&db1x00_rtc_dev);
+
return 0;
}
-late_initcall(db1x_poweroff_setup);
+device_initcall(db1x_late_setup);
/* register a pcmcia socket */
int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
diff --git a/arch/mips/include/asm/mach-pb1x00/mc146818rtc.h b/arch/mips/include/asm/mach-pb1x00/mc146818rtc.h
deleted file mode 100644
index 622c587..0000000
--- a/arch/mips/include/asm/mach-pb1x00/mc146818rtc.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1998, 2001, 03 by Ralf Baechle
- *
- * RTC routines for PC style attached Dallas chip.
- */
-#ifndef __ASM_MACH_AU1XX_MC146818RTC_H
-#define __ASM_MACH_AU1XX_MC146818RTC_H
-
-#include <asm/io.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#define RTC_PORT(x) (0x0c000000 + (x))
-#define RTC_IRQ 8
-#define PB1500_RTC_ADDR 0x0c000000
-
-static inline unsigned char CMOS_READ(unsigned long offset)
-{
- offset <<= 2;
- return (u8)(au_readl(offset + PB1500_RTC_ADDR) & 0xff);
-}
-
-static inline void CMOS_WRITE(unsigned char data, unsigned long offset)
-{
- offset <<= 2;
- au_writel(data, offset + PB1500_RTC_ADDR);
-}
-
-#define RTC_ALWAYS_BCD 1
-
-#endif /* __ASM_MACH_AU1XX_MC146818RTC_H */
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 14/18] MTD: nand: make au1550nd.c a platform_driver
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (12 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 13/18] MIPS: Alchemy: add RTC device to all devboards Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:54 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 15/18] MIPS: Alchemy: remove unused board headers Manuel Lauss
` (3 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss, linux-mtd
Transform the au1550nd.c driver into a platform_driver and hook it
up in the PB1550 board (gen_nand works fine on the DB1550, but since
I don't have a PB1550 to test this driver stays for now).
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
Tested on the DB1550 as well.
I'd like for this to go in via the MIPS tree if at all possible.
arch/mips/alchemy/devboards/pb1550.c | 66 ++++++
arch/mips/include/asm/mach-au1x00/au1550nd.h | 16 ++
drivers/mtd/nand/au1550nd.c | 308 +++++++++++---------------
3 files changed, 215 insertions(+), 175 deletions(-)
create mode 100644 arch/mips/include/asm/mach-au1x00/au1550nd.h
diff --git a/arch/mips/alchemy/devboards/pb1550.c b/arch/mips/alchemy/devboards/pb1550.c
index e4a00a5..b37e7de 100644
--- a/arch/mips/alchemy/devboards/pb1550.c
+++ b/arch/mips/alchemy/devboards/pb1550.c
@@ -24,6 +24,7 @@
#include <linux/platform_device.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1550nd.h>
#include <asm/mach-au1x00/gpio.h>
#include <asm/mach-db1x00/bcsr.h>
#include "platform.h"
@@ -131,6 +132,67 @@ static struct platform_device pb1550_i2c_dev = {
.resource = au1550_psc2_res,
};
+static struct mtd_partition pb1550_nand_parts[] = {
+ [0] = {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ [1] = {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct au1550nd_platdata pb1550_nand_pd = {
+ .parts = pb1550_nand_parts,
+ .num_parts = ARRAY_SIZE(pb1550_nand_parts),
+ .devwidth = 0, /* x8 NAND default, needs fixing up */
+};
+
+static struct resource pb1550_nand_res[] = {
+ [0] = {
+ .start = 0x20000000,
+ .end = 0x20000fff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device pb1550_nand_dev = {
+ .name = "au1550-nand",
+ .id = -1,
+ .resource = pb1550_nand_res,
+ .num_resources = ARRAY_SIZE(pb1550_nand_res),
+ .dev = {
+ .platform_data = &pb1550_nand_pd,
+ },
+};
+
+static void __init pb1550_nand_setup(void)
+{
+ int boot_swapboot = (au_readl(MEM_STSTAT) & (0x7 << 1)) |
+ ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
+
+ switch (boot_swapboot) {
+ case 0:
+ case 2:
+ case 8:
+ case 0xC:
+ case 0xD:
+ /* x16 NAND Flash */
+ pb1550_nand_pd.devwidth = 1;
+ /* fallthrough */
+ case 1:
+ case 9:
+ case 3:
+ case 0xE:
+ case 0xF:
+ /* x8 NAND, already set up */
+ platform_device_register(&pb1550_nand_dev);
+ }
+}
+
static int __init pb1550_dev_init(void)
{
int swapped;
@@ -168,6 +230,10 @@ static int __init pb1550_dev_init(void)
AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
+ /* NAND setup */
+ gpio_direction_input(206); /* GPIO206 high */
+ pb1550_nand_setup();
+
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
platform_device_register(&pb1550_pci_host);
diff --git a/arch/mips/include/asm/mach-au1x00/au1550nd.h b/arch/mips/include/asm/mach-au1x00/au1550nd.h
new file mode 100644
index 0000000..ad4c0a0
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1550nd.h
@@ -0,0 +1,16 @@
+/*
+ * platform data for the Au1550 NAND driver
+ */
+
+#ifndef _AU1550ND_H_
+#define _AU1550ND_H_
+
+#include <linux/mtd/partitions.h>
+
+struct au1550nd_platdata {
+ struct mtd_partition *parts;
+ int num_parts;
+ int devwidth; /* 0 = 8bit device, 1 = 16bit device */
+};
+
+#endif
diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c
index fa5736b..bdebd5c 100644
--- a/drivers/mtd/nand/au1550nd.c
+++ b/drivers/mtd/nand/au1550nd.c
@@ -17,35 +17,19 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
#include <asm/io.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1550nd.h>
-#ifdef CONFIG_MIPS_PB1550
-#include <asm/mach-pb1x00/pb1550.h>
-#elif defined(CONFIG_MIPS_DB1550)
-#include <asm/mach-db1x00/db1x00.h>
-#endif
-#include <asm/mach-db1x00/bcsr.h>
-/*
- * MTD structure for NAND controller
- */
-static struct mtd_info *au1550_mtd = NULL;
-static void __iomem *p_nand;
-static int nand_width = 1; /* default x8 */
-static void (*au1550_write_byte)(struct mtd_info *, u_char);
+struct au1550nd_ctx {
+ struct mtd_info info;
+ struct nand_chip chip;
-/*
- * Define partitions for flash device
- */
-static const struct mtd_partition partition_info[] = {
- {
- .name = "NAND FS 0",
- .offset = 0,
- .size = 8 * 1024 * 1024},
- {
- .name = "NAND FS 1",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL}
+ int cs;
+ void __iomem *base;
+ void (*write_byte)(struct mtd_info *, u_char);
};
/**
@@ -262,24 +246,25 @@ static int au_verify_buf16(struct mtd_info *mtd, const u_char *buf, int len)
static void au1550_hwcontrol(struct mtd_info *mtd, int cmd)
{
- register struct nand_chip *this = mtd->priv;
+ struct au1550nd_ctx *ctx = container_of(mtd, struct au1550nd_ctx, info);
+ struct nand_chip *this = mtd->priv;
switch (cmd) {
case NAND_CTL_SETCLE:
- this->IO_ADDR_W = p_nand + MEM_STNAND_CMD;
+ this->IO_ADDR_W = ctx->base + MEM_STNAND_CMD;
break;
case NAND_CTL_CLRCLE:
- this->IO_ADDR_W = p_nand + MEM_STNAND_DATA;
+ this->IO_ADDR_W = ctx->base + MEM_STNAND_DATA;
break;
case NAND_CTL_SETALE:
- this->IO_ADDR_W = p_nand + MEM_STNAND_ADDR;
+ this->IO_ADDR_W = ctx->base + MEM_STNAND_ADDR;
break;
case NAND_CTL_CLRALE:
- this->IO_ADDR_W = p_nand + MEM_STNAND_DATA;
+ this->IO_ADDR_W = ctx->base + MEM_STNAND_DATA;
/* FIXME: Nobody knows why this is necessary,
* but it works only that way */
udelay(1);
@@ -287,7 +272,7 @@ static void au1550_hwcontrol(struct mtd_info *mtd, int cmd)
case NAND_CTL_SETNCE:
/* assert (force assert) chip enable */
- au_writel((1 << (4 + NAND_CS)), MEM_STNDCTL);
+ au_writel((1 << (4 + ctx->cs)), MEM_STNDCTL);
break;
case NAND_CTL_CLRNCE:
@@ -334,9 +319,10 @@ static void au1550_select_chip(struct mtd_info *mtd, int chip)
*/
static void au1550_command(struct mtd_info *mtd, unsigned command, int column, int page_addr)
{
- register struct nand_chip *this = mtd->priv;
+ struct au1550nd_ctx *ctx = container_of(mtd, struct au1550nd_ctx, info);
+ struct nand_chip *this = mtd->priv;
int ce_override = 0, i;
- ulong flags;
+ unsigned long flags = 0;
/* Begin command latch cycle */
au1550_hwcontrol(mtd, NAND_CTL_SETCLE);
@@ -357,9 +343,9 @@ static void au1550_command(struct mtd_info *mtd, unsigned command, int column, i
column -= 256;
readcmd = NAND_CMD_READ1;
}
- au1550_write_byte(mtd, readcmd);
+ ctx->write_byte(mtd, readcmd);
}
- au1550_write_byte(mtd, command);
+ ctx->write_byte(mtd, command);
/* Set ALE and clear CLE to start address cycle */
au1550_hwcontrol(mtd, NAND_CTL_CLRCLE);
@@ -372,10 +358,10 @@ static void au1550_command(struct mtd_info *mtd, unsigned command, int column, i
/* Adjust columns for 16 bit buswidth */
if (this->options & NAND_BUSWIDTH_16)
column >>= 1;
- au1550_write_byte(mtd, column);
+ ctx->write_byte(mtd, column);
}
if (page_addr != -1) {
- au1550_write_byte(mtd, (u8)(page_addr & 0xff));
+ ctx->write_byte(mtd, (u8)(page_addr & 0xff));
if (command == NAND_CMD_READ0 ||
command == NAND_CMD_READ1 ||
@@ -393,11 +379,12 @@ static void au1550_command(struct mtd_info *mtd, unsigned command, int column, i
au1550_hwcontrol(mtd, NAND_CTL_SETNCE);
}
- au1550_write_byte(mtd, (u8)(page_addr >> 8));
+ ctx->write_byte(mtd, (u8)(page_addr >> 8));
/* One more address cycle for devices > 32MiB */
if (this->chipsize > (32 << 20))
- au1550_write_byte(mtd, (u8)((page_addr >> 16) & 0x0f));
+ ctx->write_byte(mtd,
+ ((page_addr >> 16) & 0x0f));
}
/* Latch in address */
au1550_hwcontrol(mtd, NAND_CTL_CLRALE);
@@ -443,121 +430,79 @@ static void au1550_command(struct mtd_info *mtd, unsigned command, int column, i
while(!this->dev_ready(mtd));
}
-
-/*
- * Main initialization routine
- */
-static int __init au1xxx_nand_init(void)
+static int __devinit find_nand_cs(unsigned long nand_base)
{
- struct nand_chip *this;
- u16 boot_swapboot = 0; /* default value */
- int retval;
- u32 mem_staddr;
- u32 nand_phys;
-
- /* Allocate memory for MTD device structure and private data */
- au1550_mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL);
- if (!au1550_mtd) {
- printk("Unable to allocate NAND MTD dev structure.\n");
- return -ENOMEM;
- }
-
- /* Get pointer to private data */
- this = (struct nand_chip *)(&au1550_mtd[1]);
-
- /* Link the private data with the MTD structure */
- au1550_mtd->priv = this;
- au1550_mtd->owner = THIS_MODULE;
-
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1000_STATIC_MEM_PHYS_ADDR);
+ unsigned long addr, staddr, start, mask, end;
+ int i;
- /* MEM_STNDCTL: disable ints, disable nand boot */
- au_writel(0, MEM_STNDCTL);
+ for (i = 0; i < 4; i++) {
+ addr = 0x1000 + (i * 0x10); /* CSx */
+ staddr = __raw_readl(base + addr + 0x08); /* STADDRx */
+ /* figure out the decoded range of this CS */
+ start = (staddr << 4) & 0xfffc0000;
+ mask = (staddr << 18) & 0xfffc0000;
+ end = (start | (start - 1)) & ~(start ^ mask);
+ if ((nand_base >= start) && (nand_base < end))
+ return i;
+ }
-#ifdef CONFIG_MIPS_PB1550
- /* set gpio206 high */
- gpio_direction_input(206);
+ return -ENODEV;
+}
- boot_swapboot = (au_readl(MEM_STSTAT) & (0x7 << 1)) | ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
+static int __devinit au1550nd_probe(struct platform_device *pdev)
+{
+ struct au1550nd_platdata *pd;
+ struct au1550nd_ctx *ctx;
+ struct nand_chip *this;
+ struct resource *r;
+ int ret, cs;
- switch (boot_swapboot) {
- case 0:
- case 2:
- case 8:
- case 0xC:
- case 0xD:
- /* x16 NAND Flash */
- nand_width = 0;
- break;
- case 1:
- case 9:
- case 3:
- case 0xE:
- case 0xF:
- /* x8 NAND Flash */
- nand_width = 1;
- break;
- default:
- printk("Pb1550 NAND: bad boot:swap\n");
- retval = -EINVAL;
- goto outmem;
- }
-#endif
-
- /* Configure chip-select; normally done by boot code, e.g. YAMON */
-#ifdef NAND_STCFG
- if (NAND_CS == 0) {
- au_writel(NAND_STCFG, MEM_STCFG0);
- au_writel(NAND_STTIME, MEM_STTIME0);
- au_writel(NAND_STADDR, MEM_STADDR0);
+ pd = pdev->dev.platform_data;
+ if (!pd) {
+ dev_err(&pdev->dev, "missing platform data\n");
+ return -ENODEV;
}
- if (NAND_CS == 1) {
- au_writel(NAND_STCFG, MEM_STCFG1);
- au_writel(NAND_STTIME, MEM_STTIME1);
- au_writel(NAND_STADDR, MEM_STADDR1);
+
+ ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+ if (!ctx) {
+ dev_err(&pdev->dev, "no memory for NAND context\n");
+ return -ENOMEM;
}
- if (NAND_CS == 2) {
- au_writel(NAND_STCFG, MEM_STCFG2);
- au_writel(NAND_STTIME, MEM_STTIME2);
- au_writel(NAND_STADDR, MEM_STADDR2);
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r) {
+ dev_err(&pdev->dev, "no NAND memory resource\n");
+ ret = -ENODEV;
+ goto out1;
}
- if (NAND_CS == 3) {
- au_writel(NAND_STCFG, MEM_STCFG3);
- au_writel(NAND_STTIME, MEM_STTIME3);
- au_writel(NAND_STADDR, MEM_STADDR3);
+ if (request_mem_region(r->start, resource_size(r), "au1550-nand")) {
+ dev_err(&pdev->dev, "cannot claim NAND memory area\n");
+ ret = -ENOMEM;
+ goto out1;
}
-#endif
-
- /* Locate NAND chip-select in order to determine NAND phys address */
- mem_staddr = 0x00000000;
- if (((au_readl(MEM_STCFG0) & 0x7) == 0x5) && (NAND_CS == 0))
- mem_staddr = au_readl(MEM_STADDR0);
- else if (((au_readl(MEM_STCFG1) & 0x7) == 0x5) && (NAND_CS == 1))
- mem_staddr = au_readl(MEM_STADDR1);
- else if (((au_readl(MEM_STCFG2) & 0x7) == 0x5) && (NAND_CS == 2))
- mem_staddr = au_readl(MEM_STADDR2);
- else if (((au_readl(MEM_STCFG3) & 0x7) == 0x5) && (NAND_CS == 3))
- mem_staddr = au_readl(MEM_STADDR3);
-
- if (mem_staddr == 0x00000000) {
- printk("Au1xxx NAND: ERROR WITH NAND CHIP-SELECT\n");
- kfree(au1550_mtd);
- return 1;
+
+ ctx->base = ioremap_nocache(r->start, 0x1000);
+ if (!ctx->base) {
+ dev_err(&pdev->dev, "cannot remap NAND memory area\n");
+ ret = -ENODEV;
+ goto out2;
}
- nand_phys = (mem_staddr << 4) & 0xFFFC0000;
- p_nand = ioremap(nand_phys, 0x1000);
+ this = &ctx->chip;
+ ctx->info.priv = this;
+ ctx->info.owner = THIS_MODULE;
- /* make controller and MTD agree */
- if (NAND_CS == 0)
- nand_width = au_readl(MEM_STCFG0) & (1 << 22);
- if (NAND_CS == 1)
- nand_width = au_readl(MEM_STCFG1) & (1 << 22);
- if (NAND_CS == 2)
- nand_width = au_readl(MEM_STCFG2) & (1 << 22);
- if (NAND_CS == 3)
- nand_width = au_readl(MEM_STCFG3) & (1 << 22);
+ /* figure out which CS# r->start belongs to */
+ cs = find_nand_cs(r->start);
+ if (cs < 0) {
+ dev_err(&pdev->dev, "cannot detect NAND chipselect\n");
+ ret = -ENODEV;
+ goto out3;
+ }
+ ctx->cs = cs;
- /* Set address of hardware control function */
this->dev_ready = au1550_device_ready;
this->select_chip = au1550_select_chip;
this->cmdfunc = au1550_command;
@@ -568,54 +513,67 @@ static int __init au1xxx_nand_init(void)
this->options = NAND_NO_AUTOINCR;
- if (!nand_width)
+ if (pd->devwidth)
this->options |= NAND_BUSWIDTH_16;
- this->read_byte = (!nand_width) ? au_read_byte16 : au_read_byte;
- au1550_write_byte = (!nand_width) ? au_write_byte16 : au_write_byte;
+ this->read_byte = (pd->devwidth) ? au_read_byte16 : au_read_byte;
+ ctx->write_byte = (pd->devwidth) ? au_write_byte16 : au_write_byte;
this->read_word = au_read_word;
- this->write_buf = (!nand_width) ? au_write_buf16 : au_write_buf;
- this->read_buf = (!nand_width) ? au_read_buf16 : au_read_buf;
- this->verify_buf = (!nand_width) ? au_verify_buf16 : au_verify_buf;
-
- /* Scan to find existence of the device */
- if (nand_scan(au1550_mtd, 1)) {
- retval = -ENXIO;
- goto outio;
+ this->write_buf = (pd->devwidth) ? au_write_buf16 : au_write_buf;
+ this->read_buf = (pd->devwidth) ? au_read_buf16 : au_read_buf;
+ this->verify_buf = (pd->devwidth) ? au_verify_buf16 : au_verify_buf;
+
+ ret = nand_scan(&ctx->info, 1);
+ if (ret) {
+ dev_err(&pdev->dev, "NAND scan failed with %d\n", ret);
+ goto out3;
}
- /* Register the partitions */
- mtd_device_register(au1550_mtd, partition_info,
- ARRAY_SIZE(partition_info));
+ mtd_device_register(&ctx->info, pd->parts, pd->num_parts);
return 0;
- outio:
- iounmap(p_nand);
-
- outmem:
- kfree(au1550_mtd);
- return retval;
+out3:
+ iounmap(ctx->base);
+out2:
+ release_mem_region(r->start, resource_size(r));
+out1:
+ kfree(ctx);
+ return ret;
}
-module_init(au1xxx_nand_init);
-
-/*
- * Clean up routine
- */
-static void __exit au1550_cleanup(void)
+static int __devexit au1550nd_remove(struct platform_device *pdev)
{
- /* Release resources, unregister device */
- nand_release(au1550_mtd);
-
- /* Free the MTD device structure */
- kfree(au1550_mtd);
+ struct au1550nd_ctx *ctx = platform_get_drvdata(pdev);
+ struct resource *r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- /* Unmap */
- iounmap(p_nand);
+ nand_release(&ctx->info);
+ iounmap(ctx->base);
+ release_mem_region(r->start, 0x1000);
+ kfree(ctx);
+ return 0;
}
-module_exit(au1550_cleanup);
+static struct platform_driver au1550nd_driver = {
+ .driver = {
+ .name = "au1550-nand",
+ .owner = THIS_MODULE,
+ },
+ .probe = au1550nd_probe,
+ .remove = __devexit_p(au1550nd_remove),
+};
+
+static int __init au1550nd_load(void)
+{
+ return platform_driver_register(&au1550nd_driver);
+};
+
+static void __exit au1550nd_exit(void)
+{
+ platform_driver_unregister(&au1550nd_driver);
+};
+module_init(au1550nd_load);
+module_exit(au1550nd_exit);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Embedded Edge, LLC");
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 15/18] MIPS: Alchemy: remove unused board headers
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (13 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 14/18] MTD: nand: make au1550nd.c a platform_driver Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:55 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 16/18] net/irda: convert au1k_ir to platform driver Manuel Lauss
` (2 subsequent siblings)
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
The information in those headers is no longer necessary.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/Platform | 3 -
arch/mips/include/asm/mach-db1x00/db1x00.h | 63 ------------------------
arch/mips/include/asm/mach-pb1x00/pb1550.h | 73 ----------------------------
3 files changed, 0 insertions(+), 139 deletions(-)
delete mode 100644 arch/mips/include/asm/mach-db1x00/db1x00.h
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1550.h
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 33f80e8..7956274 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -8,21 +8,18 @@ platform-$(CONFIG_MIPS_ALCHEMY) += alchemy/common/
# AMD Alchemy Pb1100 eval board
#
platform-$(CONFIG_MIPS_PB1100) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1100) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1100) += 0xffffffff80100000
#
# AMD Alchemy Pb1500 eval board
#
platform-$(CONFIG_MIPS_PB1500) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1500) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1500) += 0xffffffff80100000
#
# AMD Alchemy Pb1550 eval board
#
platform-$(CONFIG_MIPS_PB1550) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1550) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1550) += 0xffffffff80100000
#
diff --git a/arch/mips/include/asm/mach-db1x00/db1x00.h b/arch/mips/include/asm/mach-db1x00/db1x00.h
deleted file mode 100644
index 51f1ebf..0000000
--- a/arch/mips/include/asm/mach-db1x00/db1x00.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * AMD Alchemy DBAu1x00 Reference Boards
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#ifndef __ASM_DB1X00_H
-#define __ASM_DB1X00_H
-
-#include <asm/mach-au1x00/au1xxx_psc.h>
-
-/*
- * NAND defines
- *
- * Timing values as described in databook, * ns value stripped of the
- * lower 2 bits.
- * These defines are here rather than an Au1550 generic file because
- * the parts chosen on another board may be different and may require
- * different timings.
- */
-#define NAND_T_H (18 >> 2)
-#define NAND_T_PUL (30 >> 2)
-#define NAND_T_SU (30 >> 2)
-#define NAND_T_WH (30 >> 2)
-
-/* Bitfield shift amounts */
-#define NAND_T_H_SHIFT 0
-#define NAND_T_PUL_SHIFT 4
-#define NAND_T_SU_SHIFT 8
-#define NAND_T_WH_SHIFT 12
-
-#define NAND_TIMING (((NAND_T_H & 0xF) << NAND_T_H_SHIFT) | \
- ((NAND_T_PUL & 0xF) << NAND_T_PUL_SHIFT) | \
- ((NAND_T_SU & 0xF) << NAND_T_SU_SHIFT) | \
- ((NAND_T_WH & 0xF) << NAND_T_WH_SHIFT))
-#define NAND_CS 1
-
-/* Should be done by YAMON */
-#define NAND_STCFG 0x00400005 /* 8-bit NAND */
-#define NAND_STTIME 0x00007774 /* valid for 396 MHz SD=2 only */
-#define NAND_STADDR 0x12000FFF /* physical address 0x20000000 */
-
-#endif /* __ASM_DB1X00_H */
diff --git a/arch/mips/include/asm/mach-pb1x00/pb1550.h b/arch/mips/include/asm/mach-pb1x00/pb1550.h
deleted file mode 100644
index 443b88a..0000000
--- a/arch/mips/include/asm/mach-pb1x00/pb1550.h
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * AMD Alchemy Semi PB1550 Reference Board
- * Board Registers defines.
- *
- * Copyright 2004 Embedded Edge LLC.
- * Copyright 2005 Ralf Baechle (ralf@linux-mips.org)
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#ifndef __ASM_PB1550_H
-#define __ASM_PB1550_H
-
-#include <linux/types.h>
-#include <asm/mach-au1x00/au1xxx_psc.h>
-
-#define DBDMA_AC97_TX_CHAN AU1550_DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN AU1550_DSCR_CMD0_PSC1_RX
-#define DBDMA_I2S_TX_CHAN AU1550_DSCR_CMD0_PSC3_TX
-#define DBDMA_I2S_RX_CHAN AU1550_DSCR_CMD0_PSC3_RX
-
-#define SPI_PSC_BASE AU1550_PSC0_PHYS_ADDR
-#define AC97_PSC_BASE AU1550_PSC1_PHYS_ADDR
-#define SMBUS_PSC_BASE AU1550_PSC2_PHYS_ADDR
-#define I2S_PSC_BASE AU1550_PSC3_PHYS_ADDR
-
-/*
- * Timing values as described in databook, * ns value stripped of
- * lower 2 bits.
- * These defines are here rather than an SOC1550 generic file because
- * the parts chosen on another board may be different and may require
- * different timings.
- */
-#define NAND_T_H (18 >> 2)
-#define NAND_T_PUL (30 >> 2)
-#define NAND_T_SU (30 >> 2)
-#define NAND_T_WH (30 >> 2)
-
-/* Bitfield shift amounts */
-#define NAND_T_H_SHIFT 0
-#define NAND_T_PUL_SHIFT 4
-#define NAND_T_SU_SHIFT 8
-#define NAND_T_WH_SHIFT 12
-
-#define NAND_TIMING (((NAND_T_H & 0xF) << NAND_T_H_SHIFT) | \
- ((NAND_T_PUL & 0xF) << NAND_T_PUL_SHIFT) | \
- ((NAND_T_SU & 0xF) << NAND_T_SU_SHIFT) | \
- ((NAND_T_WH & 0xF) << NAND_T_WH_SHIFT))
-
-#define NAND_CS 1
-
-/* Should be done by YAMON */
-#define NAND_STCFG 0x00400005 /* 8-bit NAND */
-#define NAND_STTIME 0x00007774 /* valid for 396 MHz SD=2 only */
-#define NAND_STADDR 0x12000FFF /* physical address 0x20000000 */
-
-#endif /* __ASM_PB1550_H */
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 16/18] net/irda: convert au1k_ir to platform driver.
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (14 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 15/18] MIPS: Alchemy: remove unused board headers Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:55 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 17/18] MIPS: Alchemy: hook up IrDA on DB1000/DB1100 Manuel Lauss
2011-11-01 19:03 ` [PATCH 18/18] MIPS: Alchemy: Touchscreen support on DB1100 Manuel Lauss
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss, Samuel Ortiz, netdev
Moderate driver cleanup:
convert to platform driver, get rid of board-specific code.
Driver loads and runs on a DB1100 board. But since I have no other
IrDA hardware to exchange data with I can't say whether it really sends
and receives.
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
I'd like for this to go in via the MIPS tree since other mips patches depend
on it.
arch/mips/include/asm/mach-au1x00/au1000.h | 52 +-
drivers/net/irda/Kconfig | 6 +-
drivers/net/irda/au1000_ircc.h | 125 ---
drivers/net/irda/au1k_ir.c | 1226 +++++++++++++++------------
4 files changed, 700 insertions(+), 709 deletions(-)
delete mode 100644 drivers/net/irda/au1000_ircc.h
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index 65f1262..569828d 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -1265,44 +1265,20 @@ enum soc_au1200_ints {
#define SSI_ENABLE_CD (1 << 1)
#define SSI_ENABLE_E (1 << 0)
-/* IrDA Controller */
-#define IRDA_BASE 0xB0300000
-#define IR_RING_PTR_STATUS (IRDA_BASE + 0x00)
-#define IR_RING_BASE_ADDR_H (IRDA_BASE + 0x04)
-#define IR_RING_BASE_ADDR_L (IRDA_BASE + 0x08)
-#define IR_RING_SIZE (IRDA_BASE + 0x0C)
-#define IR_RING_PROMPT (IRDA_BASE + 0x10)
-#define IR_RING_ADDR_CMPR (IRDA_BASE + 0x14)
-#define IR_INT_CLEAR (IRDA_BASE + 0x18)
-#define IR_CONFIG_1 (IRDA_BASE + 0x20)
-# define IR_RX_INVERT_LED (1 << 0)
-# define IR_TX_INVERT_LED (1 << 1)
-# define IR_ST (1 << 2)
-# define IR_SF (1 << 3)
-# define IR_SIR (1 << 4)
-# define IR_MIR (1 << 5)
-# define IR_FIR (1 << 6)
-# define IR_16CRC (1 << 7)
-# define IR_TD (1 << 8)
-# define IR_RX_ALL (1 << 9)
-# define IR_DMA_ENABLE (1 << 10)
-# define IR_RX_ENABLE (1 << 11)
-# define IR_TX_ENABLE (1 << 12)
-# define IR_LOOPBACK (1 << 14)
-# define IR_SIR_MODE (IR_SIR | IR_DMA_ENABLE | \
- IR_RX_ALL | IR_RX_ENABLE | IR_SF | IR_16CRC)
-#define IR_SIR_FLAGS (IRDA_BASE + 0x24)
-#define IR_ENABLE (IRDA_BASE + 0x28)
-# define IR_RX_STATUS (1 << 9)
-# define IR_TX_STATUS (1 << 10)
-#define IR_READ_PHY_CONFIG (IRDA_BASE + 0x2C)
-#define IR_WRITE_PHY_CONFIG (IRDA_BASE + 0x30)
-#define IR_MAX_PKT_LEN (IRDA_BASE + 0x34)
-#define IR_RX_BYTE_CNT (IRDA_BASE + 0x38)
-#define IR_CONFIG_2 (IRDA_BASE + 0x3C)
-# define IR_MODE_INV (1 << 0)
-# define IR_ONE_PIN (1 << 1)
-#define IR_INTERFACE_CONFIG (IRDA_BASE + 0x40)
+
+/*
+ * The IrDA peripheral has an IRFIRSEL pin, but on the DB/PB boards it's not
+ * used to select FIR/SIR mode on the transceiver but as a GPIO. Instead a
+ * CPLD has to be told about the mode.
+ */
+#define AU1000_IRDA_PHY_MODE_OFF 0
+#define AU1000_IRDA_PHY_MODE_SIR 1
+#define AU1000_IRDA_PHY_MODE_FIR 2
+
+struct au1k_irda_platform_data {
+ void(*set_phy_mode)(int mode);
+};
+
/* GPIO */
#define SYS_PINFUNC 0xB190002C
diff --git a/drivers/net/irda/Kconfig b/drivers/net/irda/Kconfig
index d423d18..e535137 100644
--- a/drivers/net/irda/Kconfig
+++ b/drivers/net/irda/Kconfig
@@ -313,8 +313,12 @@ config TOSHIBA_FIR
donauboe.
config AU1000_FIR
- tristate "Alchemy Au1000 SIR/FIR"
+ tristate "Alchemy IrDA SIR/FIR"
depends on IRDA && MIPS_ALCHEMY
+ help
+ Say Y/M here to build suppor the the IrDA peripheral on the
+ Alchemy Au1000 and Au1100 SoCs.
+ Say M to build a module; it will be called au1k_ir.ko
config SMC_IRCC_FIR
tristate "SMSC IrCC (EXPERIMENTAL)"
diff --git a/drivers/net/irda/au1000_ircc.h b/drivers/net/irda/au1000_ircc.h
deleted file mode 100644
index c072c09..0000000
--- a/drivers/net/irda/au1000_ircc.h
+++ /dev/null
@@ -1,125 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Au1000 IrDA driver.
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef AU1000_IRCC_H
-#define AU1000_IRCC_H
-
-#include <linux/time.h>
-
-#include <linux/spinlock.h>
-#include <linux/pm.h>
-#include <asm/io.h>
-
-#define NUM_IR_IFF 1
-#define NUM_IR_DESC 64
-#define RING_SIZE_4 0x0
-#define RING_SIZE_16 0x3
-#define RING_SIZE_64 0xF
-#define MAX_NUM_IR_DESC 64
-#define MAX_BUF_SIZE 2048
-
-#define BPS_115200 0
-#define BPS_57600 1
-#define BPS_38400 2
-#define BPS_19200 5
-#define BPS_9600 11
-#define BPS_2400 47
-
-/* Ring descriptor flags */
-#define AU_OWN (1<<7) /* tx,rx */
-
-#define IR_DIS_CRC (1<<6) /* tx */
-#define IR_BAD_CRC (1<<5) /* tx */
-#define IR_NEED_PULSE (1<<4) /* tx */
-#define IR_FORCE_UNDER (1<<3) /* tx */
-#define IR_DISABLE_TX (1<<2) /* tx */
-#define IR_HW_UNDER (1<<0) /* tx */
-#define IR_TX_ERROR (IR_DIS_CRC|IR_BAD_CRC|IR_HW_UNDER)
-
-#define IR_PHY_ERROR (1<<6) /* rx */
-#define IR_CRC_ERROR (1<<5) /* rx */
-#define IR_MAX_LEN (1<<4) /* rx */
-#define IR_FIFO_OVER (1<<3) /* rx */
-#define IR_SIR_ERROR (1<<2) /* rx */
-#define IR_RX_ERROR (IR_PHY_ERROR|IR_CRC_ERROR| \
- IR_MAX_LEN|IR_FIFO_OVER|IR_SIR_ERROR)
-
-typedef struct db_dest {
- struct db_dest *pnext;
- volatile u32 *vaddr;
- dma_addr_t dma_addr;
-} db_dest_t;
-
-
-typedef struct ring_desc {
- u8 count_0; /* 7:0 */
- u8 count_1; /* 12:8 */
- u8 reserved;
- u8 flags;
- u8 addr_0; /* 7:0 */
- u8 addr_1; /* 15:8 */
- u8 addr_2; /* 23:16 */
- u8 addr_3; /* 31:24 */
-} ring_dest_t;
-
-
-/* Private data for each instance */
-struct au1k_private {
-
- db_dest_t *pDBfree;
- db_dest_t db[2*NUM_IR_DESC];
- volatile ring_dest_t *rx_ring[NUM_IR_DESC];
- volatile ring_dest_t *tx_ring[NUM_IR_DESC];
- db_dest_t *rx_db_inuse[NUM_IR_DESC];
- db_dest_t *tx_db_inuse[NUM_IR_DESC];
- u32 rx_head;
- u32 tx_head;
- u32 tx_tail;
- u32 tx_full;
-
- iobuff_t rx_buff;
-
- struct net_device *netdev;
-
- struct timeval stamp;
- struct timeval now;
- struct qos_info qos;
- struct irlap_cb *irlap;
-
- u8 open;
- u32 speed;
- u32 newspeed;
-
- u32 intr_work_done; /* number of Rx and Tx pkts processed in the isr */
- struct timer_list timer;
-
- spinlock_t lock; /* For serializing operations */
-};
-#endif /* AU1000_IRCC_H */
diff --git a/drivers/net/irda/au1k_ir.c b/drivers/net/irda/au1k_ir.c
index 670bb05..fc503aa 100644
--- a/drivers/net/irda/au1k_ir.c
+++ b/drivers/net/irda/au1k_ir.c
@@ -18,101 +18,220 @@
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*/
-#include <linux/module.h>
-#include <linux/types.h>
+
#include <linux/init.h>
-#include <linux/errno.h>
+#include <linux/module.h>
#include <linux/netdevice.h>
-#include <linux/slab.h>
-#include <linux/rtnetlink.h>
#include <linux/interrupt.h>
-#include <linux/pm.h>
-#include <linux/bitops.h>
-
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/au1000.h>
-#if defined(CONFIG_MIPS_DB1000)
-#include <asm/mach-db1x00/bcsr.h>
-#else
-#error au1k_ir: unsupported board
-#endif
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/time.h>
+#include <linux/types.h>
#include <net/irda/irda.h>
#include <net/irda/irmod.h>
#include <net/irda/wrapper.h>
#include <net/irda/irda_device.h>
-#include "au1000_ircc.h"
+#include <asm/mach-au1x00/au1000.h>
+
+/* registers */
+#define IR_RING_PTR_STATUS 0x00
+#define IR_RING_BASE_ADDR_H 0x04
+#define IR_RING_BASE_ADDR_L 0x08
+#define IR_RING_SIZE 0x0C
+#define IR_RING_PROMPT 0x10
+#define IR_RING_ADDR_CMPR 0x14
+#define IR_INT_CLEAR 0x18
+#define IR_CONFIG_1 0x20
+#define IR_SIR_FLAGS 0x24
+#define IR_STATUS 0x28
+#define IR_READ_PHY_CONFIG 0x2C
+#define IR_WRITE_PHY_CONFIG 0x30
+#define IR_MAX_PKT_LEN 0x34
+#define IR_RX_BYTE_CNT 0x38
+#define IR_CONFIG_2 0x3C
+#define IR_ENABLE 0x40
+
+/* Config1 */
+#define IR_RX_INVERT_LED (1 << 0)
+#define IR_TX_INVERT_LED (1 << 1)
+#define IR_ST (1 << 2)
+#define IR_SF (1 << 3)
+#define IR_SIR (1 << 4)
+#define IR_MIR (1 << 5)
+#define IR_FIR (1 << 6)
+#define IR_16CRC (1 << 7)
+#define IR_TD (1 << 8)
+#define IR_RX_ALL (1 << 9)
+#define IR_DMA_ENABLE (1 << 10)
+#define IR_RX_ENABLE (1 << 11)
+#define IR_TX_ENABLE (1 << 12)
+#define IR_LOOPBACK (1 << 14)
+#define IR_SIR_MODE (IR_SIR | IR_DMA_ENABLE | \
+ IR_RX_ALL | IR_RX_ENABLE | IR_SF | \
+ IR_16CRC)
+
+/* ir_status */
+#define IR_RX_STATUS (1 << 9)
+#define IR_TX_STATUS (1 << 10)
+#define IR_PHYEN (1 << 15)
+
+/* ir_write_phy_config */
+#define IR_BR(x) (((x) & 0x3f) << 10) /* baud rate */
+#define IR_PW(x) (((x) & 0x1f) << 5) /* pulse width */
+#define IR_P(x) ((x) & 0x1f) /* preamble bits */
+
+/* Config2 */
+#define IR_MODE_INV (1 << 0)
+#define IR_ONE_PIN (1 << 1)
+#define IR_PHYCLK_40MHZ (0 << 2)
+#define IR_PHYCLK_48MHZ (1 << 2)
+#define IR_PHYCLK_56MHZ (2 << 2)
+#define IR_PHYCLK_64MHZ (3 << 2)
+#define IR_DP (1 << 4)
+#define IR_DA (1 << 5)
+#define IR_FLT_HIGH (0 << 6)
+#define IR_FLT_MEDHI (1 << 6)
+#define IR_FLT_MEDLO (2 << 6)
+#define IR_FLT_LO (3 << 6)
+#define IR_IEN (1 << 8)
+
+/* ir_enable */
+#define IR_HC (1 << 3) /* divide SBUS clock by 2 */
+#define IR_CE (1 << 2) /* clock enable */
+#define IR_C (1 << 1) /* coherency bit */
+#define IR_BE (1 << 0) /* set in big endian mode */
+
+#define NUM_IR_DESC 64
+#define RING_SIZE_4 0x0
+#define RING_SIZE_16 0x3
+#define RING_SIZE_64 0xF
+#define MAX_NUM_IR_DESC 64
+#define MAX_BUF_SIZE 2048
+
+/* Ring descriptor flags */
+#define AU_OWN (1 << 7) /* tx,rx */
+#define IR_DIS_CRC (1 << 6) /* tx */
+#define IR_BAD_CRC (1 << 5) /* tx */
+#define IR_NEED_PULSE (1 << 4) /* tx */
+#define IR_FORCE_UNDER (1 << 3) /* tx */
+#define IR_DISABLE_TX (1 << 2) /* tx */
+#define IR_HW_UNDER (1 << 0) /* tx */
+#define IR_TX_ERROR (IR_DIS_CRC | IR_BAD_CRC | IR_HW_UNDER)
+
+#define IR_PHY_ERROR (1 << 6) /* rx */
+#define IR_CRC_ERROR (1 << 5) /* rx */
+#define IR_MAX_LEN (1 << 4) /* rx */
+#define IR_FIFO_OVER (1 << 3) /* rx */
+#define IR_SIR_ERROR (1 << 2) /* rx */
+#define IR_RX_ERROR (IR_PHY_ERROR | IR_CRC_ERROR | \
+ IR_MAX_LEN | IR_FIFO_OVER | IR_SIR_ERROR)
+
+struct db_dest {
+ struct db_dest *pnext;
+ volatile u32 *vaddr;
+ dma_addr_t dma_addr;
+};
+
+struct ring_dest {
+ u8 count_0; /* 7:0 */
+ u8 count_1; /* 12:8 */
+ u8 reserved;
+ u8 flags;
+ u8 addr_0; /* 7:0 */
+ u8 addr_1; /* 15:8 */
+ u8 addr_2; /* 23:16 */
+ u8 addr_3; /* 31:24 */
+};
+
+/* Private data for each instance */
+struct au1k_private {
+ void __iomem *iobase;
+ int irq_rx, irq_tx;
+
+ struct db_dest *pDBfree;
+ struct db_dest db[2 * NUM_IR_DESC];
+ volatile struct ring_dest *rx_ring[NUM_IR_DESC];
+ volatile struct ring_dest *tx_ring[NUM_IR_DESC];
+ struct db_dest *rx_db_inuse[NUM_IR_DESC];
+ struct db_dest *tx_db_inuse[NUM_IR_DESC];
+ u32 rx_head;
+ u32 tx_head;
+ u32 tx_tail;
+ u32 tx_full;
+
+ iobuff_t rx_buff;
+
+ struct net_device *netdev;
+ struct timeval stamp;
+ struct timeval now;
+ struct qos_info qos;
+ struct irlap_cb *irlap;
+
+ u8 open;
+ u32 speed;
+ u32 newspeed;
-static int au1k_irda_net_init(struct net_device *);
-static int au1k_irda_start(struct net_device *);
-static int au1k_irda_stop(struct net_device *dev);
-static int au1k_irda_hard_xmit(struct sk_buff *, struct net_device *);
-static int au1k_irda_rx(struct net_device *);
-static void au1k_irda_interrupt(int, void *);
-static void au1k_tx_timeout(struct net_device *);
-static int au1k_irda_ioctl(struct net_device *, struct ifreq *, int);
-static int au1k_irda_set_speed(struct net_device *dev, int speed);
+ struct timer_list timer;
-static void *dma_alloc(size_t, dma_addr_t *);
-static void dma_free(void *, size_t);
+ struct resource *ioarea;
+ struct au1k_irda_platform_data *platdata;
+};
static int qos_mtt_bits = 0x07; /* 1 ms or more */
-static struct net_device *ir_devs[NUM_IR_IFF];
-static char version[] __devinitdata =
- "au1k_ircc:1.2 ppopov@mvista.com\n";
#define RUN_AT(x) (jiffies + (x))
-static DEFINE_SPINLOCK(ir_lock);
+static void au1k_irda_plat_set_phy_mode(struct au1k_private *p, int mode)
+{
+ if (p->platdata && p->platdata->set_phy_mode)
+ p->platdata->set_phy_mode(mode);
+}
-/*
- * IrDA peripheral bug. You have to read the register
- * twice to get the right value.
- */
-u32 read_ir_reg(u32 addr)
-{
- readl(addr);
- return readl(addr);
+static inline unsigned long irda_read(struct au1k_private *p,
+ unsigned long ofs)
+{
+ /*
+ * IrDA peripheral bug. You have to read the register
+ * twice to get the right value.
+ */
+ (void)__raw_readl(p->iobase + ofs);
+ return __raw_readl(p->iobase + ofs);
}
+static inline void irda_write(struct au1k_private *p, unsigned long ofs,
+ unsigned long val)
+{
+ __raw_writel(val, p->iobase + ofs);
+ wmb();
+}
/*
* Buffer allocation/deallocation routines. The buffer descriptor returned
- * has the virtual and dma address of a buffer suitable for
+ * has the virtual and dma address of a buffer suitable for
* both, receive and transmit operations.
*/
-static db_dest_t *GetFreeDB(struct au1k_private *aup)
+static struct db_dest *GetFreeDB(struct au1k_private *aup)
{
- db_dest_t *pDB;
- pDB = aup->pDBfree;
-
- if (pDB) {
- aup->pDBfree = pDB->pnext;
- }
- return pDB;
-}
+ struct db_dest *db;
+ db = aup->pDBfree;
-static void ReleaseDB(struct au1k_private *aup, db_dest_t *pDB)
-{
- db_dest_t *pDBfree = aup->pDBfree;
- if (pDBfree)
- pDBfree->pnext = pDB;
- aup->pDBfree = pDB;
+ if (db)
+ aup->pDBfree = db->pnext;
+ return db;
}
-
/*
DMA memory allocation, derived from pci_alloc_consistent.
However, the Au1000 data cache is coherent (when programmed
so), therefore we return KSEG0 address, not KSEG1.
*/
-static void *dma_alloc(size_t size, dma_addr_t * dma_handle)
+static void *dma_alloc(size_t size, dma_addr_t *dma_handle)
{
void *ret;
int gfp = GFP_ATOMIC | GFP_DMA;
- ret = (void *) __get_free_pages(gfp, get_order(size));
+ ret = (void *)__get_free_pages(gfp, get_order(size));
if (ret != NULL) {
memset(ret, 0, size);
@@ -122,7 +241,6 @@ static void *dma_alloc(size_t size, dma_addr_t * dma_handle)
return ret;
}
-
static void dma_free(void *vaddr, size_t size)
{
vaddr = (void *)KSEG0ADDR(vaddr);
@@ -130,206 +248,306 @@ static void dma_free(void *vaddr, size_t size)
}
-static void
-setup_hw_rings(struct au1k_private *aup, u32 rx_base, u32 tx_base)
+static void setup_hw_rings(struct au1k_private *aup, u32 rx_base, u32 tx_base)
{
int i;
- for (i=0; i<NUM_IR_DESC; i++) {
- aup->rx_ring[i] = (volatile ring_dest_t *)
- (rx_base + sizeof(ring_dest_t)*i);
+ for (i = 0; i < NUM_IR_DESC; i++) {
+ aup->rx_ring[i] = (volatile struct ring_dest *)
+ (rx_base + sizeof(struct ring_dest) * i);
}
- for (i=0; i<NUM_IR_DESC; i++) {
- aup->tx_ring[i] = (volatile ring_dest_t *)
- (tx_base + sizeof(ring_dest_t)*i);
+ for (i = 0; i < NUM_IR_DESC; i++) {
+ aup->tx_ring[i] = (volatile struct ring_dest *)
+ (tx_base + sizeof(struct ring_dest) * i);
}
}
-static int au1k_irda_init(void)
-{
- static unsigned version_printed = 0;
- struct au1k_private *aup;
- struct net_device *dev;
- int err;
-
- if (version_printed++ == 0) printk(version);
-
- dev = alloc_irdadev(sizeof(struct au1k_private));
- if (!dev)
- return -ENOMEM;
-
- dev->irq = AU1000_IRDA_RX_INT; /* TX has its own interrupt */
- err = au1k_irda_net_init(dev);
- if (err)
- goto out;
- err = register_netdev(dev);
- if (err)
- goto out1;
- ir_devs[0] = dev;
- printk(KERN_INFO "IrDA: Registered device %s\n", dev->name);
- return 0;
-
-out1:
- aup = netdev_priv(dev);
- dma_free((void *)aup->db[0].vaddr,
- MAX_BUF_SIZE * 2*NUM_IR_DESC);
- dma_free((void *)aup->rx_ring[0],
- 2 * MAX_NUM_IR_DESC*(sizeof(ring_dest_t)));
- kfree(aup->rx_buff.head);
-out:
- free_netdev(dev);
- return err;
-}
-
static int au1k_irda_init_iobuf(iobuff_t *io, int size)
{
io->head = kmalloc(size, GFP_KERNEL);
if (io->head != NULL) {
- io->truesize = size;
- io->in_frame = FALSE;
- io->state = OUTSIDE_FRAME;
- io->data = io->head;
+ io->truesize = size;
+ io->in_frame = FALSE;
+ io->state = OUTSIDE_FRAME;
+ io->data = io->head;
}
return io->head ? 0 : -ENOMEM;
}
-static const struct net_device_ops au1k_irda_netdev_ops = {
- .ndo_open = au1k_irda_start,
- .ndo_stop = au1k_irda_stop,
- .ndo_start_xmit = au1k_irda_hard_xmit,
- .ndo_tx_timeout = au1k_tx_timeout,
- .ndo_do_ioctl = au1k_irda_ioctl,
-};
-
-static int au1k_irda_net_init(struct net_device *dev)
+/*
+ * Set the IrDA communications speed.
+ */
+static int au1k_irda_set_speed(struct net_device *dev, int speed)
{
struct au1k_private *aup = netdev_priv(dev);
- int i, retval = 0, err;
- db_dest_t *pDB, *pDBfree;
- dma_addr_t temp;
+ volatile struct ring_dest *ptxd;
+ unsigned long control;
+ int ret = 0, timeout = 10, i;
- err = au1k_irda_init_iobuf(&aup->rx_buff, 14384);
- if (err)
- goto out1;
+ if (speed == aup->speed)
+ return ret;
- dev->netdev_ops = &au1k_irda_netdev_ops;
+ /* disable PHY first */
+ au1k_irda_plat_set_phy_mode(aup, AU1000_IRDA_PHY_MODE_OFF);
+ irda_write(aup, IR_STATUS, irda_read(aup, IR_STATUS) & ~IR_PHYEN);
- irda_init_max_qos_capabilies(&aup->qos);
+ /* disable RX/TX */
+ irda_write(aup, IR_CONFIG_1,
+ irda_read(aup, IR_CONFIG_1) & ~(IR_RX_ENABLE | IR_TX_ENABLE));
+ msleep(20);
+ while (irda_read(aup, IR_STATUS) & (IR_RX_STATUS | IR_TX_STATUS)) {
+ msleep(20);
+ if (!timeout--) {
+ printk(KERN_ERR "%s: rx/tx disable timeout\n",
+ dev->name);
+ break;
+ }
+ }
- /* The only value we must override it the baudrate */
- aup->qos.baud_rate.bits = IR_9600|IR_19200|IR_38400|IR_57600|
- IR_115200|IR_576000 |(IR_4000000 << 8);
-
- aup->qos.min_turn_time.bits = qos_mtt_bits;
- irda_qos_bits_to_value(&aup->qos);
+ /* disable DMA */
+ irda_write(aup, IR_CONFIG_1,
+ irda_read(aup, IR_CONFIG_1) & ~IR_DMA_ENABLE);
+ msleep(20);
- retval = -ENOMEM;
+ /* After we disable tx/rx. the index pointers go back to zero. */
+ aup->tx_head = aup->tx_tail = aup->rx_head = 0;
+ for (i = 0; i < NUM_IR_DESC; i++) {
+ ptxd = aup->tx_ring[i];
+ ptxd->flags = 0;
+ ptxd->count_0 = 0;
+ ptxd->count_1 = 0;
+ }
- /* Tx ring follows rx ring + 512 bytes */
- /* we need a 1k aligned buffer */
- aup->rx_ring[0] = (ring_dest_t *)
- dma_alloc(2*MAX_NUM_IR_DESC*(sizeof(ring_dest_t)), &temp);
- if (!aup->rx_ring[0])
- goto out2;
+ for (i = 0; i < NUM_IR_DESC; i++) {
+ ptxd = aup->rx_ring[i];
+ ptxd->count_0 = 0;
+ ptxd->count_1 = 0;
+ ptxd->flags = AU_OWN;
+ }
- /* allocate the data buffers */
- aup->db[0].vaddr =
- (void *)dma_alloc(MAX_BUF_SIZE * 2*NUM_IR_DESC, &temp);
- if (!aup->db[0].vaddr)
- goto out3;
+ if (speed == 4000000)
+ au1k_irda_plat_set_phy_mode(aup, AU1000_IRDA_PHY_MODE_FIR);
+ else
+ au1k_irda_plat_set_phy_mode(aup, AU1000_IRDA_PHY_MODE_SIR);
- setup_hw_rings(aup, (u32)aup->rx_ring[0], (u32)aup->rx_ring[0] + 512);
+ switch (speed) {
+ case 9600:
+ irda_write(aup, IR_WRITE_PHY_CONFIG, IR_BR(11) | IR_PW(12));
+ irda_write(aup, IR_CONFIG_1, IR_SIR_MODE);
+ break;
+ case 19200:
+ irda_write(aup, IR_WRITE_PHY_CONFIG, IR_BR(5) | IR_PW(12));
+ irda_write(aup, IR_CONFIG_1, IR_SIR_MODE);
+ break;
+ case 38400:
+ irda_write(aup, IR_WRITE_PHY_CONFIG, IR_BR(2) | IR_PW(12));
+ irda_write(aup, IR_CONFIG_1, IR_SIR_MODE);
+ break;
+ case 57600:
+ irda_write(aup, IR_WRITE_PHY_CONFIG, IR_BR(1) | IR_PW(12));
+ irda_write(aup, IR_CONFIG_1, IR_SIR_MODE);
+ break;
+ case 115200:
+ irda_write(aup, IR_WRITE_PHY_CONFIG, IR_PW(12));
+ irda_write(aup, IR_CONFIG_1, IR_SIR_MODE);
+ break;
+ case 4000000:
+ irda_write(aup, IR_WRITE_PHY_CONFIG, IR_P(15));
+ irda_write(aup, IR_CONFIG_1, IR_FIR | IR_DMA_ENABLE |
+ IR_RX_ENABLE);
+ break;
+ default:
+ printk(KERN_ERR "%s unsupported speed %x\n", dev->name, speed);
+ ret = -EINVAL;
+ break;
+ }
- pDBfree = NULL;
- pDB = aup->db;
- for (i=0; i<(2*NUM_IR_DESC); i++) {
- pDB->pnext = pDBfree;
- pDBfree = pDB;
- pDB->vaddr =
- (u32 *)((unsigned)aup->db[0].vaddr + MAX_BUF_SIZE*i);
- pDB->dma_addr = (dma_addr_t)virt_to_bus(pDB->vaddr);
- pDB++;
+ aup->speed = speed;
+ irda_write(aup, IR_STATUS, irda_read(aup, IR_STATUS) | IR_PHYEN);
+
+ control = irda_read(aup, IR_STATUS);
+ irda_write(aup, IR_RING_PROMPT, 0);
+
+ if (control & (1 << 14)) {
+ printk(KERN_ERR "%s: configuration error\n", dev->name);
+ } else {
+ if (control & (1 << 11))
+ printk(KERN_DEBUG "%s Valid SIR config\n", dev->name);
+ if (control & (1 << 12))
+ printk(KERN_DEBUG "%s Valid MIR config\n", dev->name);
+ if (control & (1 << 13))
+ printk(KERN_DEBUG "%s Valid FIR config\n", dev->name);
+ if (control & (1 << 10))
+ printk(KERN_DEBUG "%s TX enabled\n", dev->name);
+ if (control & (1 << 9))
+ printk(KERN_DEBUG "%s RX enabled\n", dev->name);
}
- aup->pDBfree = pDBfree;
- /* attach a data buffer to each descriptor */
- for (i=0; i<NUM_IR_DESC; i++) {
- pDB = GetFreeDB(aup);
- if (!pDB) goto out;
- aup->rx_ring[i]->addr_0 = (u8)(pDB->dma_addr & 0xff);
- aup->rx_ring[i]->addr_1 = (u8)((pDB->dma_addr>>8) & 0xff);
- aup->rx_ring[i]->addr_2 = (u8)((pDB->dma_addr>>16) & 0xff);
- aup->rx_ring[i]->addr_3 = (u8)((pDB->dma_addr>>24) & 0xff);
- aup->rx_db_inuse[i] = pDB;
+ return ret;
+}
+
+static void update_rx_stats(struct net_device *dev, u32 status, u32 count)
+{
+ struct net_device_stats *ps = &dev->stats;
+
+ ps->rx_packets++;
+
+ if (status & IR_RX_ERROR) {
+ ps->rx_errors++;
+ if (status & (IR_PHY_ERROR | IR_FIFO_OVER))
+ ps->rx_missed_errors++;
+ if (status & IR_MAX_LEN)
+ ps->rx_length_errors++;
+ if (status & IR_CRC_ERROR)
+ ps->rx_crc_errors++;
+ } else
+ ps->rx_bytes += count;
+}
+
+static void update_tx_stats(struct net_device *dev, u32 status, u32 pkt_len)
+{
+ struct net_device_stats *ps = &dev->stats;
+
+ ps->tx_packets++;
+ ps->tx_bytes += pkt_len;
+
+ if (status & IR_TX_ERROR) {
+ ps->tx_errors++;
+ ps->tx_aborted_errors++;
}
- for (i=0; i<NUM_IR_DESC; i++) {
- pDB = GetFreeDB(aup);
- if (!pDB) goto out;
- aup->tx_ring[i]->addr_0 = (u8)(pDB->dma_addr & 0xff);
- aup->tx_ring[i]->addr_1 = (u8)((pDB->dma_addr>>8) & 0xff);
- aup->tx_ring[i]->addr_2 = (u8)((pDB->dma_addr>>16) & 0xff);
- aup->tx_ring[i]->addr_3 = (u8)((pDB->dma_addr>>24) & 0xff);
- aup->tx_ring[i]->count_0 = 0;
- aup->tx_ring[i]->count_1 = 0;
- aup->tx_ring[i]->flags = 0;
- aup->tx_db_inuse[i] = pDB;
+}
+
+static void au1k_tx_ack(struct net_device *dev)
+{
+ struct au1k_private *aup = netdev_priv(dev);
+ volatile struct ring_dest *ptxd;
+
+ ptxd = aup->tx_ring[aup->tx_tail];
+ while (!(ptxd->flags & AU_OWN) && (aup->tx_tail != aup->tx_head)) {
+ update_tx_stats(dev, ptxd->flags,
+ (ptxd->count_1 << 8) | ptxd->count_0);
+ ptxd->count_0 = 0;
+ ptxd->count_1 = 0;
+ wmb();
+ aup->tx_tail = (aup->tx_tail + 1) & (NUM_IR_DESC - 1);
+ ptxd = aup->tx_ring[aup->tx_tail];
+
+ if (aup->tx_full) {
+ aup->tx_full = 0;
+ netif_wake_queue(dev);
+ }
}
-#if defined(CONFIG_MIPS_DB1000)
- /* power on */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
- BCSR_RESETS_IRDA_MODE_FULL);
-#endif
+ if (aup->tx_tail == aup->tx_head) {
+ if (aup->newspeed) {
+ au1k_irda_set_speed(dev, aup->newspeed);
+ aup->newspeed = 0;
+ } else {
+ irda_write(aup, IR_CONFIG_1,
+ irda_read(aup, IR_CONFIG_1) & ~IR_TX_ENABLE);
+ irda_write(aup, IR_CONFIG_1,
+ irda_read(aup, IR_CONFIG_1) | IR_RX_ENABLE);
+ irda_write(aup, IR_RING_PROMPT, 0);
+ }
+ }
+}
- return 0;
+static int au1k_irda_rx(struct net_device *dev)
+{
+ struct au1k_private *aup = netdev_priv(dev);
+ volatile struct ring_dest *prxd;
+ struct sk_buff *skb;
+ struct db_dest *pDB;
+ u32 flags, count;
-out3:
- dma_free((void *)aup->rx_ring[0],
- 2 * MAX_NUM_IR_DESC*(sizeof(ring_dest_t)));
-out2:
- kfree(aup->rx_buff.head);
-out1:
- printk(KERN_ERR "au1k_init_module failed. Returns %d\n", retval);
- return retval;
+ prxd = aup->rx_ring[aup->rx_head];
+ flags = prxd->flags;
+
+ while (!(flags & AU_OWN)) {
+ pDB = aup->rx_db_inuse[aup->rx_head];
+ count = (prxd->count_1 << 8) | prxd->count_0;
+ if (!(flags & IR_RX_ERROR)) {
+ /* good frame */
+ update_rx_stats(dev, flags, count);
+ skb = alloc_skb(count + 1, GFP_ATOMIC);
+ if (skb == NULL) {
+ dev->stats.rx_dropped++;
+ continue;
+ }
+ skb_reserve(skb, 1);
+ if (aup->speed == 4000000)
+ skb_put(skb, count);
+ else
+ skb_put(skb, count - 2);
+ skb_copy_to_linear_data(skb, (void *)pDB->vaddr,
+ count - 2);
+ skb->dev = dev;
+ skb_reset_mac_header(skb);
+ skb->protocol = htons(ETH_P_IRDA);
+ netif_rx(skb);
+ prxd->count_0 = 0;
+ prxd->count_1 = 0;
+ }
+ prxd->flags |= AU_OWN;
+ aup->rx_head = (aup->rx_head + 1) & (NUM_IR_DESC - 1);
+ irda_write(aup, IR_RING_PROMPT, 0);
+
+ /* next descriptor */
+ prxd = aup->rx_ring[aup->rx_head];
+ flags = prxd->flags;
+
+ }
+ return 0;
}
+static irqreturn_t au1k_irda_interrupt(int dummy, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct au1k_private *aup = netdev_priv(dev);
+
+ irda_write(aup, IR_INT_CLEAR, 0); /* ack irda interrupts */
+
+ au1k_irda_rx(dev);
+ au1k_tx_ack(dev);
+
+ return IRQ_HANDLED;
+}
static int au1k_init(struct net_device *dev)
{
struct au1k_private *aup = netdev_priv(dev);
+ u32 enable, ring_address;
int i;
- u32 control;
- u32 ring_address;
- /* bring the device out of reset */
- control = 0xe; /* coherent, clock enable, one half system clock */
-
+ enable = IR_HC | IR_CE | IR_C;
#ifndef CONFIG_CPU_LITTLE_ENDIAN
- control |= 1;
+ enable |= IR_BE;
#endif
aup->tx_head = 0;
aup->tx_tail = 0;
aup->rx_head = 0;
- for (i=0; i<NUM_IR_DESC; i++) {
+ for (i = 0; i < NUM_IR_DESC; i++)
aup->rx_ring[i]->flags = AU_OWN;
- }
- writel(control, IR_INTERFACE_CONFIG);
- au_sync_delay(10);
+ irda_write(aup, IR_ENABLE, enable);
+ msleep(20);
- writel(read_ir_reg(IR_ENABLE) & ~0x8000, IR_ENABLE); /* disable PHY */
- au_sync_delay(1);
+ /* disable PHY */
+ au1k_irda_plat_set_phy_mode(aup, AU1000_IRDA_PHY_MODE_OFF);
+ irda_write(aup, IR_STATUS, irda_read(aup, IR_STATUS) & ~IR_PHYEN);
+ msleep(20);
- writel(MAX_BUF_SIZE, IR_MAX_PKT_LEN);
+ irda_write(aup, IR_MAX_PKT_LEN, MAX_BUF_SIZE);
ring_address = (u32)virt_to_phys((void *)aup->rx_ring[0]);
- writel(ring_address >> 26, IR_RING_BASE_ADDR_H);
- writel((ring_address >> 10) & 0xffff, IR_RING_BASE_ADDR_L);
+ irda_write(aup, IR_RING_BASE_ADDR_H, ring_address >> 26);
+ irda_write(aup, IR_RING_BASE_ADDR_L, (ring_address >> 10) & 0xffff);
- writel(RING_SIZE_64<<8 | RING_SIZE_64<<12, IR_RING_SIZE);
+ irda_write(aup, IR_RING_SIZE,
+ (RING_SIZE_64 << 8) | (RING_SIZE_64 << 12));
- writel(1<<2 | IR_ONE_PIN, IR_CONFIG_2); /* 48MHz */
- writel(0, IR_RING_ADDR_CMPR);
+ irda_write(aup, IR_CONFIG_2, IR_PHYCLK_48MHZ | IR_ONE_PIN);
+ irda_write(aup, IR_RING_ADDR_CMPR, 0);
au1k_irda_set_speed(dev, 9600);
return 0;
@@ -337,25 +555,28 @@ static int au1k_init(struct net_device *dev)
static int au1k_irda_start(struct net_device *dev)
{
- int retval;
- char hwname[32];
struct au1k_private *aup = netdev_priv(dev);
+ char hwname[32];
+ int retval;
- if ((retval = au1k_init(dev))) {
+ retval = au1k_init(dev);
+ if (retval) {
printk(KERN_ERR "%s: error in au1k_init\n", dev->name);
return retval;
}
- if ((retval = request_irq(AU1000_IRDA_TX_INT, au1k_irda_interrupt,
- 0, dev->name, dev))) {
- printk(KERN_ERR "%s: unable to get IRQ %d\n",
+ retval = request_irq(aup->irq_tx, &au1k_irda_interrupt, 0,
+ dev->name, dev);
+ if (retval) {
+ printk(KERN_ERR "%s: unable to get IRQ %d\n",
dev->name, dev->irq);
return retval;
}
- if ((retval = request_irq(AU1000_IRDA_RX_INT, au1k_irda_interrupt,
- 0, dev->name, dev))) {
- free_irq(AU1000_IRDA_TX_INT, dev);
- printk(KERN_ERR "%s: unable to get IRQ %d\n",
+ retval = request_irq(aup->irq_rx, &au1k_irda_interrupt, 0,
+ dev->name, dev);
+ if (retval) {
+ free_irq(aup->irq_tx, dev);
+ printk(KERN_ERR "%s: unable to get IRQ %d\n",
dev->name, dev->irq);
return retval;
}
@@ -365,9 +586,13 @@ static int au1k_irda_start(struct net_device *dev)
aup->irlap = irlap_open(dev, &aup->qos, hwname);
netif_start_queue(dev);
- writel(read_ir_reg(IR_CONFIG_2) | 1<<8, IR_CONFIG_2); /* int enable */
+ /* int enable */
+ irda_write(aup, IR_CONFIG_2, irda_read(aup, IR_CONFIG_2) | IR_IEN);
- aup->timer.expires = RUN_AT((3*HZ));
+ /* power up */
+ au1k_irda_plat_set_phy_mode(aup, AU1000_IRDA_PHY_MODE_SIR);
+
+ aup->timer.expires = RUN_AT((3 * HZ));
aup->timer.data = (unsigned long)dev;
return 0;
}
@@ -376,11 +601,12 @@ static int au1k_irda_stop(struct net_device *dev)
{
struct au1k_private *aup = netdev_priv(dev);
+ au1k_irda_plat_set_phy_mode(aup, AU1000_IRDA_PHY_MODE_OFF);
+
/* disable interrupts */
- writel(read_ir_reg(IR_CONFIG_2) & ~(1<<8), IR_CONFIG_2);
- writel(0, IR_CONFIG_1);
- writel(0, IR_INTERFACE_CONFIG); /* disable clock */
- au_sync();
+ irda_write(aup, IR_CONFIG_2, irda_read(aup, IR_CONFIG_2) & ~IR_IEN);
+ irda_write(aup, IR_CONFIG_1, 0);
+ irda_write(aup, IR_ENABLE, 0); /* disable clock */
if (aup->irlap) {
irlap_close(aup->irlap);
@@ -391,83 +617,12 @@ static int au1k_irda_stop(struct net_device *dev)
del_timer(&aup->timer);
/* disable the interrupt */
- free_irq(AU1000_IRDA_TX_INT, dev);
- free_irq(AU1000_IRDA_RX_INT, dev);
- return 0;
-}
-
-static void __exit au1k_irda_exit(void)
-{
- struct net_device *dev = ir_devs[0];
- struct au1k_private *aup = netdev_priv(dev);
-
- unregister_netdev(dev);
-
- dma_free((void *)aup->db[0].vaddr,
- MAX_BUF_SIZE * 2*NUM_IR_DESC);
- dma_free((void *)aup->rx_ring[0],
- 2 * MAX_NUM_IR_DESC*(sizeof(ring_dest_t)));
- kfree(aup->rx_buff.head);
- free_netdev(dev);
-}
-
-
-static inline void
-update_tx_stats(struct net_device *dev, u32 status, u32 pkt_len)
-{
- struct au1k_private *aup = netdev_priv(dev);
- struct net_device_stats *ps = &aup->stats;
-
- ps->tx_packets++;
- ps->tx_bytes += pkt_len;
-
- if (status & IR_TX_ERROR) {
- ps->tx_errors++;
- ps->tx_aborted_errors++;
- }
-}
-
-
-static void au1k_tx_ack(struct net_device *dev)
-{
- struct au1k_private *aup = netdev_priv(dev);
- volatile ring_dest_t *ptxd;
-
- ptxd = aup->tx_ring[aup->tx_tail];
- while (!(ptxd->flags & AU_OWN) && (aup->tx_tail != aup->tx_head)) {
- update_tx_stats(dev, ptxd->flags,
- ptxd->count_1<<8 | ptxd->count_0);
- ptxd->count_0 = 0;
- ptxd->count_1 = 0;
- au_sync();
-
- aup->tx_tail = (aup->tx_tail + 1) & (NUM_IR_DESC - 1);
- ptxd = aup->tx_ring[aup->tx_tail];
-
- if (aup->tx_full) {
- aup->tx_full = 0;
- netif_wake_queue(dev);
- }
- }
+ free_irq(aup->irq_tx, dev);
+ free_irq(aup->irq_rx, dev);
- if (aup->tx_tail == aup->tx_head) {
- if (aup->newspeed) {
- au1k_irda_set_speed(dev, aup->newspeed);
- aup->newspeed = 0;
- }
- else {
- writel(read_ir_reg(IR_CONFIG_1) & ~IR_TX_ENABLE,
- IR_CONFIG_1);
- au_sync();
- writel(read_ir_reg(IR_CONFIG_1) | IR_RX_ENABLE,
- IR_CONFIG_1);
- writel(0, IR_RING_PROMPT);
- au_sync();
- }
- }
+ return 0;
}
-
/*
* Au1000 transmit routine.
*/
@@ -475,15 +630,12 @@ static int au1k_irda_hard_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct au1k_private *aup = netdev_priv(dev);
int speed = irda_get_next_speed(skb);
- volatile ring_dest_t *ptxd;
- u32 len;
-
- u32 flags;
- db_dest_t *pDB;
+ volatile struct ring_dest *ptxd;
+ struct db_dest *pDB;
+ u32 len, flags;
- if (speed != aup->speed && speed != -1) {
+ if (speed != aup->speed && speed != -1)
aup->newspeed = speed;
- }
if ((skb->len == 0) && (aup->newspeed)) {
if (aup->tx_tail == aup->tx_head) {
@@ -501,138 +653,47 @@ static int au1k_irda_hard_xmit(struct sk_buff *skb, struct net_device *dev)
printk(KERN_DEBUG "%s: tx_full\n", dev->name);
netif_stop_queue(dev);
aup->tx_full = 1;
- return NETDEV_TX_BUSY;
- }
- else if (((aup->tx_head + 1) & (NUM_IR_DESC - 1)) == aup->tx_tail) {
+ return 1;
+ } else if (((aup->tx_head + 1) & (NUM_IR_DESC - 1)) == aup->tx_tail) {
printk(KERN_DEBUG "%s: tx_full\n", dev->name);
netif_stop_queue(dev);
aup->tx_full = 1;
- return NETDEV_TX_BUSY;
+ return 1;
}
pDB = aup->tx_db_inuse[aup->tx_head];
#if 0
- if (read_ir_reg(IR_RX_BYTE_CNT) != 0) {
- printk("tx warning: rx byte cnt %x\n",
- read_ir_reg(IR_RX_BYTE_CNT));
+ if (irda_read(aup, IR_RX_BYTE_CNT) != 0) {
+ printk(KERN_DEBUG "tx warning: rx byte cnt %x\n",
+ irda_read(aup, IR_RX_BYTE_CNT));
}
#endif
-
+
if (aup->speed == 4000000) {
/* FIR */
- skb_copy_from_linear_data(skb, pDB->vaddr, skb->len);
+ skb_copy_from_linear_data(skb, (void *)pDB->vaddr, skb->len);
ptxd->count_0 = skb->len & 0xff;
ptxd->count_1 = (skb->len >> 8) & 0xff;
-
- }
- else {
+ } else {
/* SIR */
len = async_wrap_skb(skb, (u8 *)pDB->vaddr, MAX_BUF_SIZE);
ptxd->count_0 = len & 0xff;
ptxd->count_1 = (len >> 8) & 0xff;
ptxd->flags |= IR_DIS_CRC;
- au_writel(au_readl(0xae00000c) & ~(1<<13), 0xae00000c);
}
ptxd->flags |= AU_OWN;
- au_sync();
+ wmb();
- writel(read_ir_reg(IR_CONFIG_1) | IR_TX_ENABLE, IR_CONFIG_1);
- writel(0, IR_RING_PROMPT);
- au_sync();
+ irda_write(aup, IR_CONFIG_1,
+ irda_read(aup, IR_CONFIG_1) | IR_TX_ENABLE);
+ irda_write(aup, IR_RING_PROMPT, 0);
dev_kfree_skb(skb);
aup->tx_head = (aup->tx_head + 1) & (NUM_IR_DESC - 1);
return NETDEV_TX_OK;
}
-
-static inline void
-update_rx_stats(struct net_device *dev, u32 status, u32 count)
-{
- struct au1k_private *aup = netdev_priv(dev);
- struct net_device_stats *ps = &aup->stats;
-
- ps->rx_packets++;
-
- if (status & IR_RX_ERROR) {
- ps->rx_errors++;
- if (status & (IR_PHY_ERROR|IR_FIFO_OVER))
- ps->rx_missed_errors++;
- if (status & IR_MAX_LEN)
- ps->rx_length_errors++;
- if (status & IR_CRC_ERROR)
- ps->rx_crc_errors++;
- }
- else
- ps->rx_bytes += count;
-}
-
-/*
- * Au1000 receive routine.
- */
-static int au1k_irda_rx(struct net_device *dev)
-{
- struct au1k_private *aup = netdev_priv(dev);
- struct sk_buff *skb;
- volatile ring_dest_t *prxd;
- u32 flags, count;
- db_dest_t *pDB;
-
- prxd = aup->rx_ring[aup->rx_head];
- flags = prxd->flags;
-
- while (!(flags & AU_OWN)) {
- pDB = aup->rx_db_inuse[aup->rx_head];
- count = prxd->count_1<<8 | prxd->count_0;
- if (!(flags & IR_RX_ERROR)) {
- /* good frame */
- update_rx_stats(dev, flags, count);
- skb=alloc_skb(count+1,GFP_ATOMIC);
- if (skb == NULL) {
- aup->netdev->stats.rx_dropped++;
- continue;
- }
- skb_reserve(skb, 1);
- if (aup->speed == 4000000)
- skb_put(skb, count);
- else
- skb_put(skb, count-2);
- skb_copy_to_linear_data(skb, pDB->vaddr, count - 2);
- skb->dev = dev;
- skb_reset_mac_header(skb);
- skb->protocol = htons(ETH_P_IRDA);
- netif_rx(skb);
- prxd->count_0 = 0;
- prxd->count_1 = 0;
- }
- prxd->flags |= AU_OWN;
- aup->rx_head = (aup->rx_head + 1) & (NUM_IR_DESC - 1);
- writel(0, IR_RING_PROMPT);
- au_sync();
-
- /* next descriptor */
- prxd = aup->rx_ring[aup->rx_head];
- flags = prxd->flags;
-
- }
- return 0;
-}
-
-
-static irqreturn_t au1k_irda_interrupt(int dummy, void *dev_id)
-{
- struct net_device *dev = dev_id;
-
- writel(0, IR_INT_CLEAR); /* ack irda interrupts */
-
- au1k_irda_rx(dev);
- au1k_tx_ack(dev);
-
- return IRQ_HANDLED;
-}
-
-
/*
* The Tx ring has been full longer than the watchdog timeout
* value. The transmitter must be hung?
@@ -650,142 +711,7 @@ static void au1k_tx_timeout(struct net_device *dev)
netif_wake_queue(dev);
}
-
-/*
- * Set the IrDA communications speed.
- */
-static int
-au1k_irda_set_speed(struct net_device *dev, int speed)
-{
- unsigned long flags;
- struct au1k_private *aup = netdev_priv(dev);
- u32 control;
- int ret = 0, timeout = 10, i;
- volatile ring_dest_t *ptxd;
-#if defined(CONFIG_MIPS_DB1000)
- unsigned long irda_resets;
-#endif
-
- if (speed == aup->speed)
- return ret;
-
- spin_lock_irqsave(&ir_lock, flags);
-
- /* disable PHY first */
- writel(read_ir_reg(IR_ENABLE) & ~0x8000, IR_ENABLE);
-
- /* disable RX/TX */
- writel(read_ir_reg(IR_CONFIG_1) & ~(IR_RX_ENABLE|IR_TX_ENABLE),
- IR_CONFIG_1);
- au_sync_delay(1);
- while (read_ir_reg(IR_ENABLE) & (IR_RX_STATUS | IR_TX_STATUS)) {
- mdelay(1);
- if (!timeout--) {
- printk(KERN_ERR "%s: rx/tx disable timeout\n",
- dev->name);
- break;
- }
- }
-
- /* disable DMA */
- writel(read_ir_reg(IR_CONFIG_1) & ~IR_DMA_ENABLE, IR_CONFIG_1);
- au_sync_delay(1);
-
- /*
- * After we disable tx/rx. the index pointers
- * go back to zero.
- */
- aup->tx_head = aup->tx_tail = aup->rx_head = 0;
- for (i=0; i<NUM_IR_DESC; i++) {
- ptxd = aup->tx_ring[i];
- ptxd->flags = 0;
- ptxd->count_0 = 0;
- ptxd->count_1 = 0;
- }
-
- for (i=0; i<NUM_IR_DESC; i++) {
- ptxd = aup->rx_ring[i];
- ptxd->count_0 = 0;
- ptxd->count_1 = 0;
- ptxd->flags = AU_OWN;
- }
-
- if (speed == 4000000) {
-#if defined(CONFIG_MIPS_DB1000)
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_FIR_SEL);
-#else /* Pb1000 and Pb1100 */
- writel(1<<13, CPLD_AUX1);
-#endif
- }
- else {
-#if defined(CONFIG_MIPS_DB1000)
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_FIR_SEL, 0);
-#else /* Pb1000 and Pb1100 */
- writel(readl(CPLD_AUX1) & ~(1<<13), CPLD_AUX1);
-#endif
- }
-
- switch (speed) {
- case 9600:
- writel(11<<10 | 12<<5, IR_WRITE_PHY_CONFIG);
- writel(IR_SIR_MODE, IR_CONFIG_1);
- break;
- case 19200:
- writel(5<<10 | 12<<5, IR_WRITE_PHY_CONFIG);
- writel(IR_SIR_MODE, IR_CONFIG_1);
- break;
- case 38400:
- writel(2<<10 | 12<<5, IR_WRITE_PHY_CONFIG);
- writel(IR_SIR_MODE, IR_CONFIG_1);
- break;
- case 57600:
- writel(1<<10 | 12<<5, IR_WRITE_PHY_CONFIG);
- writel(IR_SIR_MODE, IR_CONFIG_1);
- break;
- case 115200:
- writel(12<<5, IR_WRITE_PHY_CONFIG);
- writel(IR_SIR_MODE, IR_CONFIG_1);
- break;
- case 4000000:
- writel(0xF, IR_WRITE_PHY_CONFIG);
- writel(IR_FIR|IR_DMA_ENABLE|IR_RX_ENABLE, IR_CONFIG_1);
- break;
- default:
- printk(KERN_ERR "%s unsupported speed %x\n", dev->name, speed);
- ret = -EINVAL;
- break;
- }
-
- aup->speed = speed;
- writel(read_ir_reg(IR_ENABLE) | 0x8000, IR_ENABLE);
- au_sync();
-
- control = read_ir_reg(IR_ENABLE);
- writel(0, IR_RING_PROMPT);
- au_sync();
-
- if (control & (1<<14)) {
- printk(KERN_ERR "%s: configuration error\n", dev->name);
- }
- else {
- if (control & (1<<11))
- printk(KERN_DEBUG "%s Valid SIR config\n", dev->name);
- if (control & (1<<12))
- printk(KERN_DEBUG "%s Valid MIR config\n", dev->name);
- if (control & (1<<13))
- printk(KERN_DEBUG "%s Valid FIR config\n", dev->name);
- if (control & (1<<10))
- printk(KERN_DEBUG "%s TX enabled\n", dev->name);
- if (control & (1<<9))
- printk(KERN_DEBUG "%s RX enabled\n", dev->name);
- }
-
- spin_unlock_irqrestore(&ir_lock, flags);
- return ret;
-}
-
-static int
-au1k_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
+static int au1k_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
{
struct if_irda_req *rq = (struct if_irda_req *)ifreq;
struct au1k_private *aup = netdev_priv(dev);
@@ -826,8 +752,218 @@ au1k_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
return ret;
}
+static const struct net_device_ops au1k_irda_netdev_ops = {
+ .ndo_open = au1k_irda_start,
+ .ndo_stop = au1k_irda_stop,
+ .ndo_start_xmit = au1k_irda_hard_xmit,
+ .ndo_tx_timeout = au1k_tx_timeout,
+ .ndo_do_ioctl = au1k_irda_ioctl,
+};
+
+static int __devinit au1k_irda_net_init(struct net_device *dev)
+{
+ struct au1k_private *aup = netdev_priv(dev);
+ struct db_dest *pDB, *pDBfree;
+ int i, err, retval = 0;
+ dma_addr_t temp;
+
+ err = au1k_irda_init_iobuf(&aup->rx_buff, 14384);
+ if (err)
+ goto out1;
+
+ dev->netdev_ops = &au1k_irda_netdev_ops;
+
+ irda_init_max_qos_capabilies(&aup->qos);
+
+ /* The only value we must override it the baudrate */
+ aup->qos.baud_rate.bits = IR_9600 | IR_19200 | IR_38400 |
+ IR_57600 | IR_115200 | IR_576000 | (IR_4000000 << 8);
+
+ aup->qos.min_turn_time.bits = qos_mtt_bits;
+ irda_qos_bits_to_value(&aup->qos);
+
+ retval = -ENOMEM;
+
+ /* Tx ring follows rx ring + 512 bytes */
+ /* we need a 1k aligned buffer */
+ aup->rx_ring[0] = (struct ring_dest *)
+ dma_alloc(2 * MAX_NUM_IR_DESC * (sizeof(struct ring_dest)),
+ &temp);
+ if (!aup->rx_ring[0])
+ goto out2;
+
+ /* allocate the data buffers */
+ aup->db[0].vaddr =
+ (void *)dma_alloc(MAX_BUF_SIZE * 2 * NUM_IR_DESC, &temp);
+ if (!aup->db[0].vaddr)
+ goto out3;
+
+ setup_hw_rings(aup, (u32)aup->rx_ring[0], (u32)aup->rx_ring[0] + 512);
+
+ pDBfree = NULL;
+ pDB = aup->db;
+ for (i = 0; i < (2 * NUM_IR_DESC); i++) {
+ pDB->pnext = pDBfree;
+ pDBfree = pDB;
+ pDB->vaddr =
+ (u32 *)((unsigned)aup->db[0].vaddr + (MAX_BUF_SIZE * i));
+ pDB->dma_addr = (dma_addr_t)virt_to_bus(pDB->vaddr);
+ pDB++;
+ }
+ aup->pDBfree = pDBfree;
+
+ /* attach a data buffer to each descriptor */
+ for (i = 0; i < NUM_IR_DESC; i++) {
+ pDB = GetFreeDB(aup);
+ if (!pDB)
+ goto out3;
+ aup->rx_ring[i]->addr_0 = (u8)(pDB->dma_addr & 0xff);
+ aup->rx_ring[i]->addr_1 = (u8)((pDB->dma_addr >> 8) & 0xff);
+ aup->rx_ring[i]->addr_2 = (u8)((pDB->dma_addr >> 16) & 0xff);
+ aup->rx_ring[i]->addr_3 = (u8)((pDB->dma_addr >> 24) & 0xff);
+ aup->rx_db_inuse[i] = pDB;
+ }
+ for (i = 0; i < NUM_IR_DESC; i++) {
+ pDB = GetFreeDB(aup);
+ if (!pDB)
+ goto out3;
+ aup->tx_ring[i]->addr_0 = (u8)(pDB->dma_addr & 0xff);
+ aup->tx_ring[i]->addr_1 = (u8)((pDB->dma_addr >> 8) & 0xff);
+ aup->tx_ring[i]->addr_2 = (u8)((pDB->dma_addr >> 16) & 0xff);
+ aup->tx_ring[i]->addr_3 = (u8)((pDB->dma_addr >> 24) & 0xff);
+ aup->tx_ring[i]->count_0 = 0;
+ aup->tx_ring[i]->count_1 = 0;
+ aup->tx_ring[i]->flags = 0;
+ aup->tx_db_inuse[i] = pDB;
+ }
+
+ return 0;
+
+out3:
+ dma_free((void *)aup->rx_ring[0],
+ 2 * MAX_NUM_IR_DESC * (sizeof(struct ring_dest)));
+out2:
+ kfree(aup->rx_buff.head);
+out1:
+ printk(KERN_ERR "au1k_irda_net_init() failed. Returns %d\n", retval);
+ return retval;
+}
+
+static int __devinit au1k_irda_probe(struct platform_device *pdev)
+{
+ struct au1k_private *aup;
+ struct net_device *dev;
+ struct resource *r;
+ int err;
+
+ dev = alloc_irdadev(sizeof(struct au1k_private));
+ if (!dev)
+ return -ENOMEM;
+
+ aup = netdev_priv(dev);
+
+ aup->platdata = pdev->dev.platform_data;
+
+ err = -EINVAL;
+ r = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!r)
+ goto out;
+
+ aup->irq_tx = r->start;
+
+ r = platform_get_resource(pdev, IORESOURCE_IRQ, 1);
+ if (!r)
+ goto out;
+
+ aup->irq_rx = r->start;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r)
+ goto out;
+
+ err = -EBUSY;
+ aup->ioarea = request_mem_region(r->start, r->end - r->start + 1,
+ pdev->name);
+ if (!aup->ioarea)
+ goto out;
+
+ aup->iobase = ioremap_nocache(r->start, r->end - r->start + 1);
+ if (!aup->iobase)
+ goto out2;
+
+ dev->irq = aup->irq_rx;
+
+ err = au1k_irda_net_init(dev);
+ if (err)
+ goto out3;
+ err = register_netdev(dev);
+ if (err)
+ goto out4;
+
+ platform_set_drvdata(pdev, dev);
+
+ printk(KERN_INFO "IrDA: Registered device %s\n", dev->name);
+ return 0;
+
+out4:
+ dma_free((void *)aup->db[0].vaddr,
+ MAX_BUF_SIZE * 2 * NUM_IR_DESC);
+ dma_free((void *)aup->rx_ring[0],
+ 2 * MAX_NUM_IR_DESC * (sizeof(struct ring_dest)));
+ kfree(aup->rx_buff.head);
+out3:
+ iounmap(aup->iobase);
+out2:
+ release_resource(aup->ioarea);
+ kfree(aup->ioarea);
+out:
+ free_netdev(dev);
+ return err;
+}
+
+static int __devexit au1k_irda_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct au1k_private *aup = netdev_priv(dev);
+
+ unregister_netdev(dev);
+
+ dma_free((void *)aup->db[0].vaddr,
+ MAX_BUF_SIZE * 2 * NUM_IR_DESC);
+ dma_free((void *)aup->rx_ring[0],
+ 2 * MAX_NUM_IR_DESC * (sizeof(struct ring_dest)));
+ kfree(aup->rx_buff.head);
+
+ iounmap(aup->iobase);
+ release_resource(aup->ioarea);
+ kfree(aup->ioarea);
+
+ free_netdev(dev);
+
+ return 0;
+}
+
+static struct platform_driver au1k_irda_driver = {
+ .driver = {
+ .name = "au1000-irda",
+ .owner = THIS_MODULE,
+ },
+ .probe = au1k_irda_probe,
+ .remove = __devexit_p(au1k_irda_remove),
+};
+
+static int __init au1k_irda_load(void)
+{
+ return platform_driver_register(&au1k_irda_driver);
+}
+
+static void __exit au1k_irda_unload(void)
+{
+ return platform_driver_unregister(&au1k_irda_driver);
+}
+
MODULE_AUTHOR("Pete Popov <ppopov@mvista.com>");
MODULE_DESCRIPTION("Au1000 IrDA Device Driver");
-module_init(au1k_irda_init);
-module_exit(au1k_irda_exit);
+module_init(au1k_irda_load);
+module_exit(au1k_irda_unload);
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 17/18] MIPS: Alchemy: hook up IrDA on DB1000/DB1100
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (15 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 16/18] net/irda: convert au1k_ir to platform driver Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:56 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 18/18] MIPS: Alchemy: Touchscreen support on DB1100 Manuel Lauss
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Add necessary transceiver control platform data and hook up the
IrDA peripheral on the DB1000 and DB1100 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/devboards/db1000.c | 74 ++++++++++++++++++++++++++--------
1 files changed, 57 insertions(+), 17 deletions(-)
diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c
index e531bfa..f62b180 100644
--- a/arch/mips/alchemy/devboards/db1000.c
+++ b/arch/mips/alchemy/devboards/db1000.c
@@ -65,23 +65,6 @@ void __init board_setup(void)
DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
printk(KERN_INFO "AMD Alchemy %s Board\n", board_type_str());
-
-#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
- {
- u32 pin_func;
-
- /* Set IRFIRSEL instead of GPIO15 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
- au_writel(pin_func, SYS_PINFUNC);
- /* Power off until the driver is in use */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
- BCSR_RESETS_IRDA_MODE_OFF);
- }
-#endif
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- /* Enable GPIO[31:0] inputs */
- alchemy_gpio1_input_enable();
}
@@ -388,6 +371,57 @@ static struct platform_device db1100_mmc1_dev = {
.resource = au1100_mmc1_res,
};
+/******************************************************************************/
+
+static void db1000_irda_set_phy_mode(int mode)
+{
+ unsigned short mask = BCSR_RESETS_IRDA_MODE_MASK | BCSR_RESETS_FIR_SEL;
+
+ switch (mode) {
+ case AU1000_IRDA_PHY_MODE_OFF:
+ bcsr_mod(BCSR_RESETS, mask, BCSR_RESETS_IRDA_MODE_OFF);
+ break;
+ case AU1000_IRDA_PHY_MODE_SIR:
+ bcsr_mod(BCSR_RESETS, mask, BCSR_RESETS_IRDA_MODE_FULL);
+ break;
+ case AU1000_IRDA_PHY_MODE_FIR:
+ bcsr_mod(BCSR_RESETS, mask, BCSR_RESETS_IRDA_MODE_FULL |
+ BCSR_RESETS_FIR_SEL);
+ break;
+ }
+}
+
+static struct au1k_irda_platform_data db1000_irda_platdata = {
+ .set_phy_mode = db1000_irda_set_phy_mode,
+};
+
+static struct resource au1000_irda_res[] = {
+ [0] = {
+ .start = AU1000_IRDA_PHYS_ADDR,
+ .end = AU1000_IRDA_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1000_IRDA_TX_INT,
+ .end = AU1000_IRDA_TX_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1000_IRDA_RX_INT,
+ .end = AU1000_IRDA_RX_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1000_irda_dev = {
+ .name = "au1000-irda",
+ .id = -1,
+ .dev = {
+ .platform_data = &db1000_irda_platdata,
+ },
+ .resource = au1000_irda_res,
+ .num_resources = ARRAY_SIZE(au1000_irda_res),
+};
static struct platform_device *db1x00_devs[] = {
&db1x00_codec_dev,
@@ -396,10 +430,15 @@ static struct platform_device *db1x00_devs[] = {
&db1x00_audio_dev,
};
+static struct platform_device *db1000_devs[] = {
+ &db1000_irda_dev,
+};
+
static struct platform_device *db1100_devs[] = {
&au1100_lcd_device,
&db1100_mmc0_dev,
&db1100_mmc1_dev,
+ &db1000_irda_dev,
};
static int __init db1000_dev_init(void)
@@ -433,6 +472,7 @@ static int __init db1000_dev_init(void)
d1 = AU1000_GPIO3_INT;
s0 = AU1000_GPIO1_INT;
s1 = AU1000_GPIO4_INT;
+ platform_add_devices(db1000_devs, ARRAY_SIZE(db1000_devs));
} else
return 0; /* unknown board, no further dev setup to do */
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH 18/18] MIPS: Alchemy: Touchscreen support on DB1100
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
` (16 preceding siblings ...)
2011-11-01 19:03 ` [PATCH 17/18] MIPS: Alchemy: hook up IrDA on DB1000/DB1100 Manuel Lauss
@ 2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:56 ` Ralf Baechle
17 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-01 19:03 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Wire up the ADS7846 touchscreen controller on the DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
arch/mips/alchemy/devboards/db1000.c | 56 ++++++++++++++++++++++++++++++++++
1 files changed, 56 insertions(+), 0 deletions(-)
diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c
index f62b180..e110f6d 100644
--- a/arch/mips/alchemy/devboards/db1000.c
+++ b/arch/mips/alchemy/devboards/db1000.c
@@ -27,6 +27,9 @@
#include <linux/mmc/host.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/spi/ads7846.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1000_dma.h>
#include <asm/mach-au1x00/au1100_mmc.h>
@@ -423,6 +426,43 @@ static struct platform_device db1000_irda_dev = {
.num_resources = ARRAY_SIZE(au1000_irda_res),
};
+/******************************************************************************/
+
+static struct ads7846_platform_data db1100_touch_pd = {
+ .model = 7846,
+ .vref_mv = 3300,
+ .gpio_pendown = 21,
+};
+
+static struct spi_gpio_platform_data db1100_spictl_pd = {
+ .sck = 209,
+ .mosi = 208,
+ .miso = 207,
+ .num_chipselect = 1,
+};
+
+static struct spi_board_info db1100_spi_info[] __initdata = {
+ [0] = {
+ .modalias = "ads7846",
+ .max_speed_hz = 3250000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = 0,
+ .irq = AU1100_GPIO21_INT,
+ .platform_data = &db1100_touch_pd,
+ .controller_data = (void *)210, /* for spi_gpio: CS# GPIO210 */
+ },
+};
+
+static struct platform_device db1100_spi_dev = {
+ .name = "spi_gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &db1100_spictl_pd,
+ },
+};
+
+
static struct platform_device *db1x00_devs[] = {
&db1x00_codec_dev,
&alchemy_ac97c_dma_dev,
@@ -439,12 +479,14 @@ static struct platform_device *db1100_devs[] = {
&db1100_mmc0_dev,
&db1100_mmc1_dev,
&db1000_irda_dev,
+ &db1100_spi_dev,
};
static int __init db1000_dev_init(void)
{
int board = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
int c0, c1, d0, d1, s0, s1;
+ unsigned long pfc;
if (board == BCSR_WHOAMI_DB1500) {
c0 = AU1500_GPIO2_INT;
@@ -463,6 +505,20 @@ static int __init db1000_dev_init(void)
gpio_direction_input(19); /* sd0 cd# */
gpio_direction_input(20); /* sd1 cd# */
+ gpio_direction_input(21); /* touch pendown# */
+ gpio_direction_input(207); /* SPI MISO */
+ gpio_direction_output(208, 0); /* SPI MOSI */
+ gpio_direction_output(209, 1); /* SPI SCK */
+ gpio_direction_output(210, 1); /* SPI CS# */
+
+ /* spi_gpio on SSI0 pins */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
+ pfc |= (1 << 0); /* SSI0 pins as GPIOs */
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ spi_register_board_info(db1100_spi_info,
+ ARRAY_SIZE(db1100_spi_info));
platform_add_devices(db1100_devs, ARRAY_SIZE(db1100_devs));
} else if (board == BCSR_WHOAMI_DB1000) {
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* Re: [PATCH 01/18] MIPS: Alchemy: remove PB1000 support
2011-11-01 19:03 ` [PATCH 01/18] MIPS: Alchemy: remove PB1000 support Manuel Lauss
@ 2011-11-02 11:37 ` Ralf Baechle
2011-11-02 11:53 ` [PATCH RESEND " Manuel Lauss
1 sibling, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-02 11:37 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
On Tue, Nov 01, 2011 at 08:03:27PM +0100, Manuel Lauss wrote:
> arch/mips/alchemy/Kconfig | 9 -
> arch/mips/alchemy/Platform | 7 -
> arch/mips/alchemy/common/irq.c | 11 -
> arch/mips/alchemy/devboards/Makefile | 1 -
> arch/mips/alchemy/devboards/pb1000/Makefile | 8 -
> arch/mips/alchemy/devboards/pb1000/board_setup.c | 209 ---------
> arch/mips/alchemy/devboards/prom.c | 2 +-
> arch/mips/include/asm/mach-pb1x00/pb1000.h | 87 ----
> drivers/net/irda/au1k_ir.c | 5 +-
> drivers/pcmcia/Kconfig | 4 -
> drivers/pcmcia/Makefile | 4 -
> drivers/pcmcia/au1000_generic.c | 545 ----------------------
> drivers/pcmcia/au1000_generic.h | 135 ------
> drivers/pcmcia/au1000_pb1x00.c | 294 ------------
Please repost cc'ing the net / irda and pcmcia lists and maintainers. Even
if code is only getting removed there still is a potencial for conflicts
with other patches and generally maintainers' ego prefers a full mailbox :)
Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* [PATCH RESEND 01/18] MIPS: Alchemy: remove PB1000 support
2011-11-01 19:03 ` [PATCH 01/18] MIPS: Alchemy: remove PB1000 support Manuel Lauss
2011-11-02 11:37 ` Ralf Baechle
@ 2011-11-02 11:53 ` Manuel Lauss
2011-11-09 14:48 ` Ralf Baechle
1 sibling, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-02 11:53 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss, netdev, linux-pcmcia
Noone seems to have test hardware or care anymore. Drop PB1000 support
and along with it the old Alchemy PCMCIA socket driver.
Cc: netdev@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
Resend with CC's added as requested by Ralf.
Cc'ing netdev for IrDA driver parts and pcmcia for the socket driver
removal.
arch/mips/alchemy/Kconfig | 9 -
arch/mips/alchemy/Platform | 7 -
arch/mips/alchemy/common/irq.c | 11 -
arch/mips/alchemy/devboards/Makefile | 1 -
arch/mips/alchemy/devboards/pb1000/Makefile | 8 -
arch/mips/alchemy/devboards/pb1000/board_setup.c | 209 ---------
arch/mips/alchemy/devboards/prom.c | 2 +-
arch/mips/include/asm/mach-pb1x00/pb1000.h | 87 ----
drivers/net/irda/au1k_ir.c | 5 +-
drivers/pcmcia/Kconfig | 4 -
drivers/pcmcia/Makefile | 4 -
drivers/pcmcia/au1000_generic.c | 545 ----------------------
drivers/pcmcia/au1000_generic.h | 135 ------
drivers/pcmcia/au1000_pb1x00.c | 294 ------------
14 files changed, 2 insertions(+), 1319 deletions(-)
delete mode 100644 arch/mips/alchemy/devboards/pb1000/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1000/board_setup.c
delete mode 100644 arch/mips/include/asm/mach-pb1x00/pb1000.h
delete mode 100644 drivers/pcmcia/au1000_generic.c
delete mode 100644 drivers/pcmcia/au1000_generic.h
delete mode 100644 drivers/pcmcia/au1000_pb1x00.c
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 2a68be6..5a48387 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -78,15 +78,6 @@ config MIPS_MIRAGE
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_PB1000
- bool "Alchemy PB1000 board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select SWAP_IO_SPACE
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_PB1100
bool "Alchemy PB1100 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 96e9e41..4e07967 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -5,13 +5,6 @@ platform-$(CONFIG_MIPS_ALCHEMY) += alchemy/common/
#
-# AMD Alchemy Pb1000 eval board
-#
-platform-$(CONFIG_MIPS_PB1000) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1000) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
-load-$(CONFIG_MIPS_PB1000) += 0xffffffff80100000
-
-#
# AMD Alchemy Pb1100 eval board
#
platform-$(CONFIG_MIPS_PB1100) += alchemy/devboards/
diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index 8b60ba0..2a94a64 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -35,9 +35,6 @@
#include <asm/irq_cpu.h>
#include <asm/mipsregs.h>
#include <asm/mach-au1x00/au1000.h>
-#ifdef CONFIG_MIPS_PB1000
-#include <asm/mach-pb1x00/pb1000.h>
-#endif
/* Interrupt Controller register offsets */
#define IC_CFG0RD 0x40
@@ -265,14 +262,6 @@ static void au1x_ic1_unmask(struct irq_data *d)
__raw_writel(1 << bit, base + IC_MASKSET);
__raw_writel(1 << bit, base + IC_WAKESET);
-
-/* very hacky. does the pb1000 cpld auto-disable this int?
- * nowhere in the current kernel sources is it disabled. --mlau
- */
-#if defined(CONFIG_MIPS_PB1000)
- if (d->irq == AU1000_GPIO15_INT)
- __raw_writel(0x4000, (void __iomem *)PB1000_MDR); /* enable int */
-#endif
wmb();
}
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 826449c..bea80d7 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -4,7 +4,6 @@
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_MIPS_PB1000) += pb1000/
obj-$(CONFIG_MIPS_PB1100) += pb1100/
obj-$(CONFIG_MIPS_PB1200) += pb1200/
obj-$(CONFIG_MIPS_PB1500) += pb1500/
diff --git a/arch/mips/alchemy/devboards/pb1000/Makefile b/arch/mips/alchemy/devboards/pb1000/Makefile
deleted file mode 100644
index 97c6615..0000000
--- a/arch/mips/alchemy/devboards/pb1000/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1000 board.
-#
-
-obj-y := board_setup.o
diff --git a/arch/mips/alchemy/devboards/pb1000/board_setup.c b/arch/mips/alchemy/devboards/pb1000/board_setup.c
deleted file mode 100644
index e64fdcb..0000000
--- a/arch/mips/alchemy/devboards/pb1000/board_setup.c
+++ /dev/null
@@ -1,209 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1000.h>
-#include <asm/reboot.h>
-#include <prom.h>
-
-#include "../platform.h"
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1000";
-}
-
-static void board_reset(char *c)
-{
- asm volatile ("jr %0" : : "r" (0xbfc00000));
-}
-
-static void board_power_off(void)
-{
- while (1)
- asm volatile (
- " .set mips32 \n"
- " wait \n"
- " .set mips0 \n");
-}
-
-void __init board_setup(void)
-{
- u32 pin_func, static_cfg0;
- u32 sys_freqctrl, sys_clksrc;
- u32 prid = read_c0_prid();
-
- sys_freqctrl = 0;
- sys_clksrc = 0;
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- /* CPU core freq to 48 MHz to slow it way down... */
- au_writel(4, SYS_CPUPLL);
-
- /*
- * Setup 48 MHz FREQ2 from CPUPLL for USB Host
- * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
- */
- sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* CPU core freq to 384 MHz */
- au_writel(0x20, SYS_CPUPLL);
-
- printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
- break;
-
- default: /* HC and newer */
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
- break;
- }
-
- /*
- * Route 48 MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
-
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
-
- au_writel(pin_func, SYS_PINFUNC);
-
- alchemy_gpio_direction_input(11);
- alchemy_gpio_direction_input(13);
- alchemy_gpio_direction_output(4, 0);
- alchemy_gpio_direction_output(5, 0);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Make GPIO 15 an input (for interrupt line) */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
- /* We don't need I2S, so make it available for GPIO[31:29] */
- pin_func |= SYS_PF_I2S;
- au_writel(pin_func, SYS_PINFUNC);
-
- alchemy_gpio_direction_input(15);
-
- static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
- au_writel(static_cfg0, MEM_STCFG0);
-
- /* configure RCE2* for LCD */
- au_writel(0x00000004, MEM_STCFG2);
-
- /* MEM_STTIME2 */
- au_writel(0x09000000, MEM_STTIME2);
-
- /* Set 32-bit base address decoding for RCE2* */
- au_writel(0x10003ff0, MEM_STADDR2);
-
- /*
- * PCI CPLD setup
- * Expand CE0 to cover PCI
- */
- au_writel(0x11803e40, MEM_STADDR1);
-
- /* Burst visibility on */
- au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
-
- au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */
- au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Enable Au1000 BCLK switching - note: sed1356 must not use
- * its BCLK (Au1000 LCLK) for any timings
- */
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- break;
- default: /* HC and newer */
- /*
- * Enable sys bus clock divider when IDLE state or no bus
- * activity.
- */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
- break;
- }
-
- pm_power_off = board_power_off;
- _machine_halt = board_power_off;
- _machine_restart = board_reset;
-}
-
-static int __init pb1000_init_irq(void)
-{
- irq_set_irq_type(AU1000_GPIO15_INT, IRQF_TRIGGER_LOW);
- return 0;
-}
-arch_initcall(pb1000_init_irq);
-
-static int __init pb1000_device_init(void)
-{
- return db1x_register_norflash(8 * 1024 * 1024, 4, 0);
-}
-device_initcall(pb1000_device_init);
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index e5306b5..56d7ea5 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -33,7 +33,7 @@
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_DB1000) || \
+#if defined(CONFIG_MIPS_DB1000) || \
defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500) || \
defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
diff --git a/arch/mips/include/asm/mach-pb1x00/pb1000.h b/arch/mips/include/asm/mach-pb1x00/pb1000.h
deleted file mode 100644
index 6505925..0000000
--- a/arch/mips/include/asm/mach-pb1x00/pb1000.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * Alchemy Semi Pb1000 Reference Board
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#ifndef __ASM_PB1000_H
-#define __ASM_PB1000_H
-
-/* PCMCIA PB1000 specific defines */
-#define PCMCIA_MAX_SOCK 1
-#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK + 1)
-
-#define PB1000_PCR 0xBE000000
-# define PCR_SLOT_0_VPP0 (1 << 0)
-# define PCR_SLOT_0_VPP1 (1 << 1)
-# define PCR_SLOT_0_VCC0 (1 << 2)
-# define PCR_SLOT_0_VCC1 (1 << 3)
-# define PCR_SLOT_0_RST (1 << 4)
-# define PCR_SLOT_1_VPP0 (1 << 8)
-# define PCR_SLOT_1_VPP1 (1 << 9)
-# define PCR_SLOT_1_VCC0 (1 << 10)
-# define PCR_SLOT_1_VCC1 (1 << 11)
-# define PCR_SLOT_1_RST (1 << 12)
-
-#define PB1000_MDR 0xBE000004
-# define MDR_PI (1 << 5) /* PCMCIA int latch */
-# define MDR_EPI (1 << 14) /* enable PCMCIA int */
-# define MDR_CPI (1 << 15) /* clear PCMCIA int */
-
-#define PB1000_ACR1 0xBE000008
-# define ACR1_SLOT_0_CD1 (1 << 0) /* card detect 1 */
-# define ACR1_SLOT_0_CD2 (1 << 1) /* card detect 2 */
-# define ACR1_SLOT_0_READY (1 << 2) /* ready */
-# define ACR1_SLOT_0_STATUS (1 << 3) /* status change */
-# define ACR1_SLOT_0_VS1 (1 << 4) /* voltage sense 1 */
-# define ACR1_SLOT_0_VS2 (1 << 5) /* voltage sense 2 */
-# define ACR1_SLOT_0_INPACK (1 << 6) /* inpack pin status */
-# define ACR1_SLOT_1_CD1 (1 << 8) /* card detect 1 */
-# define ACR1_SLOT_1_CD2 (1 << 9) /* card detect 2 */
-# define ACR1_SLOT_1_READY (1 << 10) /* ready */
-# define ACR1_SLOT_1_STATUS (1 << 11) /* status change */
-# define ACR1_SLOT_1_VS1 (1 << 12) /* voltage sense 1 */
-# define ACR1_SLOT_1_VS2 (1 << 13) /* voltage sense 2 */
-# define ACR1_SLOT_1_INPACK (1 << 14) /* inpack pin status */
-
-#define CPLD_AUX0 0xBE00000C
-#define CPLD_AUX1 0xBE000010
-#define CPLD_AUX2 0xBE000014
-
-/* Voltage levels */
-
-/* VPPEN1 - VPPEN0 */
-#define VPP_GND ((0 << 1) | (0 << 0))
-#define VPP_5V ((1 << 1) | (0 << 0))
-#define VPP_3V ((0 << 1) | (1 << 0))
-#define VPP_12V ((0 << 1) | (1 << 0))
-#define VPP_HIZ ((1 << 1) | (1 << 0))
-
-/* VCCEN1 - VCCEN0 */
-#define VCC_3V ((0 << 1) | (1 << 0))
-#define VCC_5V ((1 << 1) | (0 << 0))
-#define VCC_HIZ ((0 << 1) | (0 << 0))
-
-/* VPP/VCC */
-#define SET_VCC_VPP(VCC, VPP, SLOT) \
- ((((VCC) << 2) | ((VPP) << 0)) << ((SLOT) * 8))
-#endif /* __ASM_PB1000_H */
diff --git a/drivers/net/irda/au1k_ir.c b/drivers/net/irda/au1k_ir.c
index a3d696a..d1a77ef 100644
--- a/drivers/net/irda/au1k_ir.c
+++ b/drivers/net/irda/au1k_ir.c
@@ -32,10 +32,7 @@
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/au1000.h>
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_PB1100)
-#include <asm/pb1000.h>
-#elif defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
-#include <asm/db1x00.h>
+#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
#include <asm/mach-db1x00/bcsr.h>
#else
#error au1k_ir: unsupported board
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 6e318ce..c022b5c 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -155,10 +155,6 @@ config PCMCIA_M8XX
This driver is also available as a module called m8xx_pcmcia.
-config PCMCIA_AU1X00
- tristate "Au1x00 pcmcia support"
- depends on MIPS_ALCHEMY && PCMCIA
-
config PCMCIA_ALCHEMY_DEVBOARD
tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
depends on MIPS_ALCHEMY && PCMCIA
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 29935ea..ec543a4 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_PCMCIA_SA1100) += sa11xx_base.o sa1100_cs.o
obj-$(CONFIG_PCMCIA_SA1111) += sa11xx_base.o sa1111_cs.o
obj-$(CONFIG_M32R_PCC) += m32r_pcc.o
obj-$(CONFIG_M32R_CFC) += m32r_cfc.o
-obj-$(CONFIG_PCMCIA_AU1X00) += au1x00_ss.o
obj-$(CONFIG_PCMCIA_BCM63XX) += bcm63xx_pcmcia.o
obj-$(CONFIG_PCMCIA_VRC4171) += vrc4171_card.o
obj-$(CONFIG_PCMCIA_VRC4173) += vrc4173_cardu.o
@@ -39,9 +38,6 @@ obj-$(CONFIG_AT91_CF) += at91_cf.o
obj-$(CONFIG_ELECTRA_CF) += electra_cf.o
obj-$(CONFIG_PCMCIA_ALCHEMY_DEVBOARD) += db1xxx_ss.o
-au1x00_ss-y += au1000_generic.o
-au1x00_ss-$(CONFIG_MIPS_PB1000) += au1000_pb1x00.o
-
sa1111_cs-y += sa1111_generic.o
sa1111_cs-$(CONFIG_ASSABET_NEPONSET) += sa1100_neponset.o
sa1111_cs-$(CONFIG_SA1100_BADGE4) += sa1100_badge4.o
diff --git a/drivers/pcmcia/au1000_generic.c b/drivers/pcmcia/au1000_generic.c
deleted file mode 100644
index 95dd7c6..0000000
--- a/drivers/pcmcia/au1000_generic.c
+++ /dev/null
@@ -1,545 +0,0 @@
-/*
- *
- * Alchemy Semi Au1000 pcmcia driver
- *
- * Copyright 2001-2003 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@embeddedalley.com or source@mvista.com
- *
- * Copyright 2004 Pete Popov, Embedded Alley Solutions, Inc.
- * Updated the driver to 2.6. Followed the sa11xx API and largely
- * copied many of the hardware independent functions.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/cpufreq.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/notifier.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include "au1000_generic.h"
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Pete Popov <ppopov@embeddedalley.com>");
-MODULE_DESCRIPTION("Linux PCMCIA Card Services: Au1x00 Socket Controller");
-
-#if 0
-#define debug(x,args...) printk(KERN_DEBUG "%s: " x, __func__ , ##args)
-#else
-#define debug(x,args...)
-#endif
-
-#define MAP_SIZE 0x100000
-extern struct au1000_pcmcia_socket au1000_pcmcia_socket[];
-#define PCMCIA_SOCKET(x) (au1000_pcmcia_socket + (x))
-#define to_au1000_socket(x) container_of(x, struct au1000_pcmcia_socket, socket)
-
-/* Some boards like to support CF cards as IDE root devices, so they
- * grab pcmcia sockets directly.
- */
-u32 *pcmcia_base_vaddrs[2];
-extern const unsigned long mips_io_port_base;
-
-static DEFINE_MUTEX(pcmcia_sockets_lock);
-
-static int (*au1x00_pcmcia_hw_init[])(struct device *dev) = {
- au1x_board_init,
-};
-
-static int
-au1x00_pcmcia_skt_state(struct au1000_pcmcia_socket *skt)
-{
- struct pcmcia_state state;
- unsigned int stat;
-
- memset(&state, 0, sizeof(struct pcmcia_state));
-
- skt->ops->socket_state(skt, &state);
-
- stat = state.detect ? SS_DETECT : 0;
- stat |= state.ready ? SS_READY : 0;
- stat |= state.wrprot ? SS_WRPROT : 0;
- stat |= state.vs_3v ? SS_3VCARD : 0;
- stat |= state.vs_Xv ? SS_XVCARD : 0;
- stat |= skt->cs_state.Vcc ? SS_POWERON : 0;
-
- if (skt->cs_state.flags & SS_IOCARD)
- stat |= state.bvd1 ? SS_STSCHG : 0;
- else {
- if (state.bvd1 == 0)
- stat |= SS_BATDEAD;
- else if (state.bvd2 == 0)
- stat |= SS_BATWARN;
- }
- return stat;
-}
-
-/*
- * au100_pcmcia_config_skt
- *
- * Convert PCMCIA socket state to our socket configure structure.
- */
-static int
-au1x00_pcmcia_config_skt(struct au1000_pcmcia_socket *skt, socket_state_t *state)
-{
- int ret;
-
- ret = skt->ops->configure_socket(skt, state);
- if (ret == 0) {
- skt->cs_state = *state;
- }
-
- if (ret < 0)
- debug("unable to configure socket %d\n", skt->nr);
-
- return ret;
-}
-
-/* au1x00_pcmcia_sock_init()
- *
- * (Re-)Initialise the socket, turning on status interrupts
- * and PCMCIA bus. This must wait for power to stabilise
- * so that the card status signals report correctly.
- *
- * Returns: 0
- */
-static int au1x00_pcmcia_sock_init(struct pcmcia_socket *sock)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("initializing socket %u\n", skt->nr);
-
- skt->ops->socket_init(skt);
- return 0;
-}
-
-/*
- * au1x00_pcmcia_suspend()
- *
- * Remove power on the socket, disable IRQs from the card.
- * Turn off status interrupts, and disable the PCMCIA bus.
- *
- * Returns: 0
- */
-static int au1x00_pcmcia_suspend(struct pcmcia_socket *sock)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("suspending socket %u\n", skt->nr);
-
- skt->ops->socket_suspend(skt);
-
- return 0;
-}
-
-static DEFINE_SPINLOCK(status_lock);
-
-/*
- * au1x00_check_status()
- */
-static void au1x00_check_status(struct au1000_pcmcia_socket *skt)
-{
- unsigned int events;
-
- debug("entering PCMCIA monitoring thread\n");
-
- do {
- unsigned int status;
- unsigned long flags;
-
- status = au1x00_pcmcia_skt_state(skt);
-
- spin_lock_irqsave(&status_lock, flags);
- events = (status ^ skt->status) & skt->cs_state.csc_mask;
- skt->status = status;
- spin_unlock_irqrestore(&status_lock, flags);
-
- debug("events: %s%s%s%s%s%s\n",
- events == 0 ? "<NONE>" : "",
- events & SS_DETECT ? "DETECT " : "",
- events & SS_READY ? "READY " : "",
- events & SS_BATDEAD ? "BATDEAD " : "",
- events & SS_BATWARN ? "BATWARN " : "",
- events & SS_STSCHG ? "STSCHG " : "");
-
- if (events)
- pcmcia_parse_events(&skt->socket, events);
- } while (events);
-}
-
-/*
- * au1x00_pcmcia_poll_event()
- * Let's poll for events in addition to IRQs since IRQ only is unreliable...
- */
-static void au1x00_pcmcia_poll_event(unsigned long dummy)
-{
- struct au1000_pcmcia_socket *skt = (struct au1000_pcmcia_socket *)dummy;
- debug("polling for events\n");
-
- mod_timer(&skt->poll_timer, jiffies + AU1000_PCMCIA_POLL_PERIOD);
-
- au1x00_check_status(skt);
-}
-
-/* au1x00_pcmcia_get_status()
- *
- * From the sa11xx_core.c:
- * Implements the get_status() operation for the in-kernel PCMCIA
- * service (formerly SS_GetStatus in Card Services). Essentially just
- * fills in bits in `status' according to internal driver state or
- * the value of the voltage detect chipselect register.
- *
- * As a debugging note, during card startup, the PCMCIA core issues
- * three set_socket() commands in a row the first with RESET deasserted,
- * the second with RESET asserted, and the last with RESET deasserted
- * again. Following the third set_socket(), a get_status() command will
- * be issued. The kernel is looking for the SS_READY flag (see
- * setup_socket(), reset_socket(), and unreset_socket() in cs.c).
- *
- * Returns: 0
- */
-static int
-au1x00_pcmcia_get_status(struct pcmcia_socket *sock, unsigned int *status)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- skt->status = au1x00_pcmcia_skt_state(skt);
- *status = skt->status;
-
- return 0;
-}
-
-/* au1x00_pcmcia_set_socket()
- * Implements the set_socket() operation for the in-kernel PCMCIA
- * service (formerly SS_SetSocket in Card Services). We more or
- * less punt all of this work and let the kernel handle the details
- * of power configuration, reset, &c. We also record the value of
- * `state' in order to regurgitate it to the PCMCIA core later.
- *
- * Returns: 0
- */
-static int
-au1x00_pcmcia_set_socket(struct pcmcia_socket *sock, socket_state_t *state)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("for sock %u\n", skt->nr);
-
- debug("\tmask: %s%s%s%s%s%s\n\tflags: %s%s%s%s%s%s\n",
- (state->csc_mask==0)?"<NONE>":"",
- (state->csc_mask&SS_DETECT)?"DETECT ":"",
- (state->csc_mask&SS_READY)?"READY ":"",
- (state->csc_mask&SS_BATDEAD)?"BATDEAD ":"",
- (state->csc_mask&SS_BATWARN)?"BATWARN ":"",
- (state->csc_mask&SS_STSCHG)?"STSCHG ":"",
- (state->flags==0)?"<NONE>":"",
- (state->flags&SS_PWR_AUTO)?"PWR_AUTO ":"",
- (state->flags&SS_IOCARD)?"IOCARD ":"",
- (state->flags&SS_RESET)?"RESET ":"",
- (state->flags&SS_SPKR_ENA)?"SPKR_ENA ":"",
- (state->flags&SS_OUTPUT_ENA)?"OUTPUT_ENA ":"");
- debug("\tVcc %d Vpp %d irq %d\n",
- state->Vcc, state->Vpp, state->io_irq);
-
- return au1x00_pcmcia_config_skt(skt, state);
-}
-
-int
-au1x00_pcmcia_set_io_map(struct pcmcia_socket *sock, struct pccard_io_map *map)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
- unsigned int speed;
-
- if(map->map>=MAX_IO_WIN){
- debug("map (%d) out of range\n", map->map);
- return -1;
- }
-
- if(map->flags&MAP_ACTIVE){
- speed=(map->speed>0)?map->speed:AU1000_PCMCIA_IO_SPEED;
- skt->spd_io[map->map] = speed;
- }
-
- map->start=(unsigned int)(u32)skt->virt_io;
- map->stop=map->start+MAP_SIZE;
- return 0;
-
-} /* au1x00_pcmcia_set_io_map() */
-
-
-static int
-au1x00_pcmcia_set_mem_map(struct pcmcia_socket *sock, struct pccard_mem_map *map)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
- unsigned short speed = map->speed;
-
- if(map->map>=MAX_WIN){
- debug("map (%d) out of range\n", map->map);
- return -1;
- }
-
- if (map->flags & MAP_ATTRIB) {
- skt->spd_attr[map->map] = speed;
- skt->spd_mem[map->map] = 0;
- } else {
- skt->spd_attr[map->map] = 0;
- skt->spd_mem[map->map] = speed;
- }
-
- if (map->flags & MAP_ATTRIB) {
- map->static_start = skt->phys_attr + map->card_start;
- }
- else {
- map->static_start = skt->phys_mem + map->card_start;
- }
-
- debug("set_mem_map %d start %08lx card_start %08x\n",
- map->map, map->static_start, map->card_start);
- return 0;
-
-} /* au1x00_pcmcia_set_mem_map() */
-
-static struct pccard_operations au1x00_pcmcia_operations = {
- .init = au1x00_pcmcia_sock_init,
- .suspend = au1x00_pcmcia_suspend,
- .get_status = au1x00_pcmcia_get_status,
- .set_socket = au1x00_pcmcia_set_socket,
- .set_io_map = au1x00_pcmcia_set_io_map,
- .set_mem_map = au1x00_pcmcia_set_mem_map,
-};
-
-static const char *skt_names[] = {
- "PCMCIA socket 0",
- "PCMCIA socket 1",
-};
-
-struct skt_dev_info {
- int nskt;
-};
-
-int au1x00_pcmcia_socket_probe(struct device *dev, struct pcmcia_low_level *ops, int first, int nr)
-{
- struct skt_dev_info *sinfo;
- struct au1000_pcmcia_socket *skt;
- int ret, i;
-
- sinfo = kzalloc(sizeof(struct skt_dev_info), GFP_KERNEL);
- if (!sinfo) {
- ret = -ENOMEM;
- goto out;
- }
-
- sinfo->nskt = nr;
-
- /*
- * Initialise the per-socket structure.
- */
- for (i = 0; i < nr; i++) {
- skt = PCMCIA_SOCKET(i);
- memset(skt, 0, sizeof(*skt));
-
- skt->socket.resource_ops = &pccard_static_ops;
- skt->socket.ops = &au1x00_pcmcia_operations;
- skt->socket.owner = ops->owner;
- skt->socket.dev.parent = dev;
-
- init_timer(&skt->poll_timer);
- skt->poll_timer.function = au1x00_pcmcia_poll_event;
- skt->poll_timer.data = (unsigned long)skt;
- skt->poll_timer.expires = jiffies + AU1000_PCMCIA_POLL_PERIOD;
-
- skt->nr = first + i;
- skt->irq = 255;
- skt->dev = dev;
- skt->ops = ops;
-
- skt->res_skt.name = skt_names[skt->nr];
- skt->res_io.name = "io";
- skt->res_io.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
- skt->res_mem.name = "memory";
- skt->res_mem.flags = IORESOURCE_MEM;
- skt->res_attr.name = "attribute";
- skt->res_attr.flags = IORESOURCE_MEM;
-
- /*
- * PCMCIA client drivers use the inb/outb macros to access the
- * IO registers. Since mips_io_port_base is added to the
- * access address of the mips implementation of inb/outb,
- * we need to subtract it here because we want to access the
- * I/O or MEM address directly, without going through this
- * "mips_io_port_base" mechanism.
- */
- if (i == 0) {
- skt->virt_io = (void *)
- (ioremap((phys_t)AU1X_SOCK0_IO, 0x1000) -
- (u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK0_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK0_PHYS_MEM;
- }
- else {
- skt->virt_io = (void *)
- (ioremap((phys_t)AU1X_SOCK1_IO, 0x1000) -
- (u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK1_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK1_PHYS_MEM;
- }
- pcmcia_base_vaddrs[i] = (u32 *)skt->virt_io;
- ret = ops->hw_init(skt);
-
- skt->socket.features = SS_CAP_STATIC_MAP|SS_CAP_PCCARD;
- skt->socket.irq_mask = 0;
- skt->socket.map_size = MAP_SIZE;
- skt->socket.pci_irq = skt->irq;
- skt->socket.io_offset = (unsigned long)skt->virt_io;
-
- skt->status = au1x00_pcmcia_skt_state(skt);
-
- ret = pcmcia_register_socket(&skt->socket);
- if (ret)
- goto out_err;
-
- WARN_ON(skt->socket.sock != i);
-
- add_timer(&skt->poll_timer);
- }
-
- dev_set_drvdata(dev, sinfo);
- return 0;
-
-
-out_err:
- ops->hw_shutdown(skt);
- while (i-- > 0) {
- skt = PCMCIA_SOCKET(i);
-
- del_timer_sync(&skt->poll_timer);
- pcmcia_unregister_socket(&skt->socket);
- if (i == 0) {
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-#ifndef CONFIG_MIPS_XXS1500
- else {
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-#endif
- ops->hw_shutdown(skt);
-
- }
- kfree(sinfo);
-out:
- return ret;
-}
-
-int au1x00_drv_pcmcia_remove(struct platform_device *dev)
-{
- struct skt_dev_info *sinfo = platform_get_drvdata(dev);
- int i;
-
- mutex_lock(&pcmcia_sockets_lock);
- platform_set_drvdata(dev, NULL);
-
- for (i = 0; i < sinfo->nskt; i++) {
- struct au1000_pcmcia_socket *skt = PCMCIA_SOCKET(i);
-
- del_timer_sync(&skt->poll_timer);
- pcmcia_unregister_socket(&skt->socket);
- skt->ops->hw_shutdown(skt);
- au1x00_pcmcia_config_skt(skt, &dead_socket);
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-
- kfree(sinfo);
- mutex_unlock(&pcmcia_sockets_lock);
- return 0;
-}
-
-
-/*
- * PCMCIA "Driver" API
- */
-
-static int au1x00_drv_pcmcia_probe(struct platform_device *dev)
-{
- int i, ret = -ENODEV;
-
- mutex_lock(&pcmcia_sockets_lock);
- for (i=0; i < ARRAY_SIZE(au1x00_pcmcia_hw_init); i++) {
- ret = au1x00_pcmcia_hw_init[i](&dev->dev);
- if (ret == 0)
- break;
- }
- mutex_unlock(&pcmcia_sockets_lock);
- return ret;
-}
-
-static struct platform_driver au1x00_pcmcia_driver = {
- .driver = {
- .name = "au1x00-pcmcia",
- .owner = THIS_MODULE,
- },
- .probe = au1x00_drv_pcmcia_probe,
- .remove = au1x00_drv_pcmcia_remove,
-};
-
-
-/* au1x00_pcmcia_init()
- *
- * This routine performs low-level PCMCIA initialization and then
- * registers this socket driver with Card Services.
- *
- * Returns: 0 on success, -ve error code on failure
- */
-static int __init au1x00_pcmcia_init(void)
-{
- int error = 0;
- error = platform_driver_register(&au1x00_pcmcia_driver);
- return error;
-}
-
-/* au1x00_pcmcia_exit()
- * Invokes the low-level kernel service to free IRQs associated with this
- * socket controller and reset GPIO edge detection.
- */
-static void __exit au1x00_pcmcia_exit(void)
-{
- platform_driver_unregister(&au1x00_pcmcia_driver);
-}
-
-module_init(au1x00_pcmcia_init);
-module_exit(au1x00_pcmcia_exit);
diff --git a/drivers/pcmcia/au1000_generic.h b/drivers/pcmcia/au1000_generic.h
deleted file mode 100644
index 5c36bda..0000000
--- a/drivers/pcmcia/au1000_generic.h
+++ /dev/null
@@ -1,135 +0,0 @@
-/*
- * Alchemy Semi Au1000 pcmcia driver include file
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#ifndef __ASM_AU1000_PCMCIA_H
-#define __ASM_AU1000_PCMCIA_H
-
-/* include the world */
-
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-#include "cs_internal.h"
-
-#define AU1000_PCMCIA_POLL_PERIOD (2*HZ)
-#define AU1000_PCMCIA_IO_SPEED (255)
-#define AU1000_PCMCIA_MEM_SPEED (300)
-
-#define AU1X_SOCK0_IO 0xF00000000ULL
-#define AU1X_SOCK0_PHYS_ATTR 0xF40000000ULL
-#define AU1X_SOCK0_PHYS_MEM 0xF80000000ULL
-
-/* pcmcia socket 1 needs external glue logic so the memory map
- * differs from board to board.
- */
-#if defined(CONFIG_MIPS_PB1000)
-#define AU1X_SOCK1_IO 0xF08000000ULL
-#define AU1X_SOCK1_PHYS_ATTR 0xF48000000ULL
-#define AU1X_SOCK1_PHYS_MEM 0xF88000000ULL
-#endif
-
-struct pcmcia_state {
- unsigned detect: 1,
- ready: 1,
- wrprot: 1,
- bvd1: 1,
- bvd2: 1,
- vs_3v: 1,
- vs_Xv: 1;
-};
-
-struct pcmcia_configure {
- unsigned sock: 8,
- vcc: 8,
- vpp: 8,
- output: 1,
- speaker: 1,
- reset: 1;
-};
-
-struct pcmcia_irqs {
- int sock;
- int irq;
- const char *str;
-};
-
-
-struct au1000_pcmcia_socket {
- struct pcmcia_socket socket;
-
- /*
- * Info from low level handler
- */
- struct device *dev;
- unsigned int nr;
- unsigned int irq;
-
- /*
- * Core PCMCIA state
- */
- struct pcmcia_low_level *ops;
-
- unsigned int status;
- socket_state_t cs_state;
-
- unsigned short spd_io[MAX_IO_WIN];
- unsigned short spd_mem[MAX_WIN];
- unsigned short spd_attr[MAX_WIN];
-
- struct resource res_skt;
- struct resource res_io;
- struct resource res_mem;
- struct resource res_attr;
-
- void * virt_io;
- unsigned int phys_io;
- unsigned int phys_attr;
- unsigned int phys_mem;
- unsigned short speed_io, speed_attr, speed_mem;
-
- unsigned int irq_state;
-
- struct timer_list poll_timer;
-};
-
-struct pcmcia_low_level {
- struct module *owner;
-
- int (*hw_init)(struct au1000_pcmcia_socket *);
- void (*hw_shutdown)(struct au1000_pcmcia_socket *);
-
- void (*socket_state)(struct au1000_pcmcia_socket *, struct pcmcia_state *);
- int (*configure_socket)(struct au1000_pcmcia_socket *, struct socket_state_t *);
-
- /*
- * Enable card status IRQs on (re-)initialisation. This can
- * be called at initialisation, power management event, or
- * pcmcia event.
- */
- void (*socket_init)(struct au1000_pcmcia_socket *);
-
- /*
- * Disable card status IRQs and PCMCIA bus on suspend.
- */
- void (*socket_suspend)(struct au1000_pcmcia_socket *);
-};
-
-extern int au1x_board_init(struct device *dev);
-
-#endif /* __ASM_AU1000_PCMCIA_H */
diff --git a/drivers/pcmcia/au1000_pb1x00.c b/drivers/pcmcia/au1000_pb1x00.c
deleted file mode 100644
index b239664..0000000
--- a/drivers/pcmcia/au1000_pb1x00.c
+++ /dev/null
@@ -1,294 +0,0 @@
-/*
- *
- * Alchemy Semi Pb1000 boards specific pcmcia routines.
- *
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/proc_fs.h>
-#include <linux/types.h>
-
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/au1000.h>
-#include <asm/au1000_pcmcia.h>
-
-#define debug(fmt, arg...) do { } while (0)
-
-#include <asm/pb1000.h>
-#define PCMCIA_IRQ AU1000_GPIO_15
-
-static int pb1x00_pcmcia_init(struct pcmcia_init *init)
-{
- u16 pcr;
- pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
-
- au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */
- au_sync_delay(100);
- au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */
- au_sync();
-
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(20);
-
- return PCMCIA_NUM_SOCKS;
-}
-
-static int pb1x00_pcmcia_shutdown(void)
-{
- u16 pcr;
- pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(20);
- return 0;
-}
-
-static int
-pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
-{
- u32 inserted0, inserted1;
- u16 vs0, vs1;
-
- vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
- inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
- inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
- vs0 = (vs0 >> 4) & 0x3;
- vs1 = (vs1 >> 12) & 0x3;
-
- state->ready = 0;
- state->vs_Xv = 0;
- state->vs_3v = 0;
- state->detect = 0;
-
- if (sock == 0) {
- if (inserted0) {
- switch (vs0) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "pb1x00 bad VS (%d)\n",
- vs0);
- return 0;
- }
- state->detect = 1;
- }
- }
- else {
- if (inserted1) {
- switch (vs1) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "pb1x00 bad VS (%d)\n",
- vs1);
- return 0;
- }
- state->detect = 1;
- }
- }
-
- if (state->detect) {
- state->ready = 1;
- }
-
- state->bvd1=1;
- state->bvd2=1;
- state->wrprot=0;
- return 1;
-}
-
-
-static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
-{
-
- if(info->sock > PCMCIA_MAX_SOCK) return -1;
-
- /*
- * Even in the case of the Pb1000, both sockets are connected
- * to the same irq line.
- */
- info->irq = PCMCIA_IRQ;
-
- return 0;
-}
-
-
-static int
-pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
-{
- u16 pcr;
-
- if(configure->sock > PCMCIA_MAX_SOCK) return -1;
-
- pcr = au_readl(PB1000_PCR);
-
- if (configure->sock == 0) {
- pcr &= ~(PCR_SLOT_0_VCC0 | PCR_SLOT_0_VCC1 |
- PCR_SLOT_0_VPP0 | PCR_SLOT_0_VPP1);
- }
- else {
- pcr &= ~(PCR_SLOT_1_VCC0 | PCR_SLOT_1_VCC1 |
- PCR_SLOT_1_VPP0 | PCR_SLOT_1_VPP1);
- }
-
- pcr &= ~PCR_SLOT_0_RST;
- debug("Vcc %dV Vpp %dV, pcr %x\n",
- configure->vcc, configure->vpp, pcr);
- switch(configure->vcc){
- case 0: /* Vcc 0 */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_GND,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_12V,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_5V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 50: /* Vcc 5V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_GND,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_5V,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_12V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 33: /* Vcc 3.3V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_GND,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_5V,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_12V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- default: /* what's this ? */
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);
- printk(KERN_ERR "%s: bad Vcc %d\n",
- __func__, configure->vcc);
- break;
- }
-
- if (configure->sock == 0) {
- pcr &= ~(PCR_SLOT_0_RST);
- if (configure->reset)
- pcr |= PCR_SLOT_0_RST;
- }
- else {
- pcr &= ~(PCR_SLOT_1_RST);
- if (configure->reset)
- pcr |= PCR_SLOT_1_RST;
- }
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(300);
-
- return 0;
-}
-
-
-struct pcmcia_low_level pb1x00_pcmcia_ops = {
- pb1x00_pcmcia_init,
- pb1x00_pcmcia_shutdown,
- pb1x00_pcmcia_socket_state,
- pb1x00_pcmcia_get_irq_info,
- pb1x00_pcmcia_configure_socket
-};
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH v2 08/18] MIPS: Alchemy: merge devboard code into single per-board files.
2011-11-01 19:03 ` [PATCH 08/18] MIPS: Alchemy: merge devboard code into single per-board files Manuel Lauss
@ 2011-11-04 8:35 ` Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
0 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-04 8:35 UTC (permalink / raw)
To: Linux-MIPS, Ralf Baechle; +Cc: Manuel Lauss
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
v2: rediffed against Linus' latest git.
arch/mips/alchemy/devboards/Makefile | 16 +-
arch/mips/alchemy/devboards/db1200.c | 705 ++++++++++++++++++++++
arch/mips/alchemy/devboards/db1200/Makefile | 1 -
arch/mips/alchemy/devboards/db1200/platform.c | 648 --------------------
arch/mips/alchemy/devboards/db1200/setup.c | 81 ---
arch/mips/alchemy/devboards/db1x00.c | 256 ++++++++
arch/mips/alchemy/devboards/db1x00/Makefile | 8 -
arch/mips/alchemy/devboards/db1x00/board_setup.c | 108 ----
arch/mips/alchemy/devboards/db1x00/platform.c | 207 -------
arch/mips/alchemy/devboards/pb1100.c | 167 +++++
arch/mips/alchemy/devboards/pb1100/Makefile | 8 -
arch/mips/alchemy/devboards/pb1100/board_setup.c | 127 ----
arch/mips/alchemy/devboards/pb1100/platform.c | 77 ---
arch/mips/alchemy/devboards/pb1200.c | 464 ++++++++++++++
arch/mips/alchemy/devboards/pb1200/Makefile | 5 -
arch/mips/alchemy/devboards/pb1200/board_setup.c | 174 ------
arch/mips/alchemy/devboards/pb1200/platform.c | 339 -----------
arch/mips/alchemy/devboards/pb1500.c | 198 ++++++
arch/mips/alchemy/devboards/pb1500/Makefile | 8 -
arch/mips/alchemy/devboards/pb1500/board_setup.c | 139 -----
arch/mips/alchemy/devboards/pb1500/platform.c | 94 ---
arch/mips/alchemy/devboards/pb1550.c | 178 ++++++
arch/mips/alchemy/devboards/pb1550/Makefile | 8 -
arch/mips/alchemy/devboards/pb1550/board_setup.c | 80 ---
arch/mips/alchemy/devboards/pb1550/platform.c | 140 -----
25 files changed, 1976 insertions(+), 2260 deletions(-)
create mode 100644 arch/mips/alchemy/devboards/db1200.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1200/platform.c
delete mode 100644 arch/mips/alchemy/devboards/db1200/setup.c
create mode 100644 arch/mips/alchemy/devboards/db1x00.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/Makefile
delete mode 100644 arch/mips/alchemy/devboards/db1x00/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/db1x00/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1100.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1100/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1200.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1200/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1500.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1500/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/platform.c
create mode 100644 arch/mips/alchemy/devboards/pb1550.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/Makefile
delete mode 100644 arch/mips/alchemy/devboards/pb1550/board_setup.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/platform.c
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 3467ec9..f562852 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -4,13 +4,13 @@
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_MIPS_PB1100) += pb1100/
-obj-$(CONFIG_MIPS_PB1200) += pb1200/
-obj-$(CONFIG_MIPS_PB1500) += pb1500/
-obj-$(CONFIG_MIPS_PB1550) += pb1550/
-obj-$(CONFIG_MIPS_DB1000) += db1x00/
-obj-$(CONFIG_MIPS_DB1100) += db1x00/
-obj-$(CONFIG_MIPS_DB1200) += db1200/
+obj-$(CONFIG_MIPS_PB1100) += pb1100.o
+obj-$(CONFIG_MIPS_PB1200) += pb1200.o
+obj-$(CONFIG_MIPS_PB1500) += pb1500.o
+obj-$(CONFIG_MIPS_PB1550) += pb1550.o
+obj-$(CONFIG_MIPS_DB1000) += db1x00.o
+obj-$(CONFIG_MIPS_DB1100) += db1x00.o
+obj-$(CONFIG_MIPS_DB1200) += db1200.o
obj-$(CONFIG_MIPS_DB1300) += db1300.o
-obj-$(CONFIG_MIPS_DB1500) += db1x00/
+obj-$(CONFIG_MIPS_DB1500) += db1x00.o
obj-$(CONFIG_MIPS_DB1550) += db1550.o
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
new file mode 100644
index 0000000..43f5f1b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -0,0 +1,705 @@
+/*
+ * DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008-2011 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/smc91x.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "DB1200";
+}
+
+void __init board_setup(void)
+{
+ unsigned long freq0, clksrc, div, pfc;
+ unsigned short whoami;
+
+ bcsr_init(DB1200_BCSR_PHYS_ADDR,
+ DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
+ " Board-ID %d Daughtercard ID %d\n",
+ (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+ /* SMBus/SPI on PSC0, Audio on PSC1 */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
+ pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
+ pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
+ * CPU clock; all other clock generators off/unused.
+ */
+ div = (get_au1x00_speed() + 25000000) / 50000000;
+ if (div & 1)
+ div++;
+ div = ((div >> 1) - 1) & 0xff;
+
+ freq0 = div << SYS_FC_FRDIV0_BIT;
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+ freq0 |= SYS_FC_FE0; /* enable F0 */
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+
+ /* psc0_intclk comes 1:1 from F0 */
+ clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
+ __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
+ wmb();
+}
+
+/******************************************************************************/
+
+static struct mtd_partition db1200_spiflash_parts[] = {
+ {
+ .name = "DB1200 SPI flash",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct flash_platform_data db1200_spiflash_data = {
+ .name = "s25fl001",
+ .parts = db1200_spiflash_parts,
+ .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
+ .type = "m25p10",
+};
+
+static struct spi_board_info db1200_spi_devs[] __initdata = {
+ {
+ /* TI TMP121AIDBVR temp sensor */
+ .modalias = "tmp121",
+ .max_speed_hz = 2000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = 0,
+ },
+ {
+ /* Spansion S25FL001D0FMA SPI flash */
+ .modalias = "m25p80",
+ .max_speed_hz = 50000000,
+ .bus_num = 0,
+ .chip_select = 1,
+ .mode = 0,
+ .platform_data = &db1200_spiflash_data,
+ },
+};
+
+static struct i2c_board_info db1200_i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("24c04", 0x52), }, /* AT24C04-10 I2C eeprom */
+ { I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
+ { I2C_BOARD_INFO("wm8731", 0x1b), }, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1200_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1200_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1200_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
+ .partitions = db1200_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1200_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1200_nand_device_ready,
+ .cmd_ctrl = au1200_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1200_nand_res[] = {
+ [0] = {
+ .start = DB1200_NAND_PHYS_ADDR,
+ .end = DB1200_NAND_PHYS_ADDR + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1200_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1200_nand_res),
+ .resource = db1200_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1200_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct smc91x_platdata db1200_eth_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource db1200_eth_res[] = {
+ [0] = {
+ .start = DB1200_ETH_PHYS_ADDR,
+ .end = DB1200_ETH_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_ETH_INT,
+ .end = DB1200_ETH_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1200_eth_dev = {
+ .dev = {
+ .platform_data = &db1200_eth_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(db1200_eth_res),
+ .resource = db1200_eth_res,
+};
+
+/**********************************************************************/
+
+static struct resource db1200_ide_res[] = {
+ [0] = {
+ .start = DB1200_IDE_PHYS_ADDR,
+ .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_IDE_INT,
+ .end = DB1200_IDE_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_DMA_REQ1,
+ .end = AU1200_DSCR_CMD0_DMA_REQ1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_ide_dev = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_ide_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(db1200_ide_res),
+ .resource = db1200_ide_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1200_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+/* SD carddetects: they're supposed to be edge-triggered, but ack
+ * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
+ * is disabled and its counterpart enabled. The 500ms timeout is
+ * because the carddetect isn't debounced in hardware.
+ */
+static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ if (irq == DB1200_SD0_INSERT_INT) {
+ disable_irq_nosync(DB1200_SD0_INSERT_INT);
+ enable_irq(DB1200_SD0_EJECT_INT);
+ } else {
+ disable_irq_nosync(DB1200_SD0_EJECT_INT);
+ enable_irq(DB1200_SD0_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m */
+ mmc_cd = symbol_get(mmc_detect_change);
+ if (mmc_cd) {
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int db1200_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_eject", mmc_host);
+ if (ret) {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
+ enable_irq(DB1200_SD0_EJECT_INT);
+ else
+ enable_irq(DB1200_SD0_INSERT_INT);
+
+ } else {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ free_irq(DB1200_SD0_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void db1200_mmc_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static int db1200_mmc_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int db1200_mmc_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void db1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1200_mmc_led = {
+ .brightness_set = db1200_mmcled_set,
+};
+
+static struct au1xmmc_platform_data db1200mmc_platdata = {
+ .cd_setup = db1200_mmc_cd_setup,
+ .set_power = db1200_mmc_set_power,
+ .card_inserted = db1200_mmc_card_inserted,
+ .card_readonly = db1200_mmc_card_readonly,
+ .led = &db1200_mmc_led,
+};
+
+static struct resource au1200_mmc0_resources[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX0,
+ .end = AU1200_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX0,
+ .end = AU1200_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200mmc_platdata,
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc0_resources),
+ .resource = au1200_mmc0_resources,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_LCD_INT,
+ .end = AU1200_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1200_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1200_lcd_res),
+ .resource = au1200_lcd_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC0_TX,
+ .end = AU1200_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC0_RX,
+ .end = AU1200_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+ if (cs)
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
+ else
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1200_spi_platdata = {
+ .mainclk_hz = 50000000, /* PSC0 clock */
+ .num_chipselect = 2,
+ .activate_cs = db1200_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1200_spi_dev = {
+ .dev = {
+ .dma_mask = &spi_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &db1200_spi_platdata,
+ },
+ .name = "au1550-spi",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_psc1_res[] = {
+ [0] = {
+ .start = AU1550_PSC1_PHYS_ADDR,
+ .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC1_INT,
+ .end = AU1200_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC1_TX,
+ .end = AU1200_DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC1_RX,
+ .end = AU1200_DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+/* AC97 or I2S device */
+static struct platform_device db1200_audio_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1200_psc1_res),
+ .resource = au1200_psc1_res,
+};
+
+/* DB1200 ASoC card device */
+static struct platform_device db1200_sound_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device db1200_stac_dev = {
+ .name = "ac97-codec",
+ .id = 1, /* on PSC1 */
+};
+
+static struct platform_device db1200_audiodma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device *db1200_devs[] __initdata = {
+ NULL, /* PSC0, selected by S6.8 */
+ &db1200_ide_dev,
+ &db1200_mmc0_dev,
+ &au1200_lcd_dev,
+ &db1200_eth_dev,
+ &db1200_rtc_dev,
+ &db1200_nand_dev,
+ &db1200_audiodma_dev,
+ &db1200_audio_dev,
+ &db1200_stac_dev,
+ &db1200_sound_dev,
+};
+
+static int __init db1200_dev_init(void)
+{
+ unsigned long pfc;
+ unsigned short sw;
+ int swapped;
+
+ /* GPIO7 is low-level triggered CPLD cascade */
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
+
+ /* insert/eject pairs: one of both is always screaming. To avoid
+ * issues they must not be automatically enabled when initially
+ * requested.
+ */
+ irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
+
+ i2c_register_board_info(0, db1200_i2c_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+ spi_register_board_info(db1200_spi_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+
+ /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
+ * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+ */
+
+ /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
+ * this pin is claimed by PSC0 (unused though, but pinmux doesn't
+ * allow to free it without crippling the SPI interface).
+ * As a result, in SPI mode, OTG simply won't work (PSC0 uses
+ * it as an input pin which is pulled high on the boards).
+ */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
+
+ /* switch off OTG VBUS supply */
+ gpio_request(215, "otg-vbus");
+ gpio_direction_output(215, 1);
+
+ printk(KERN_INFO "DB1200 device configuration:\n");
+
+ sw = bcsr_read(BCSR_SWITCHES);
+ if (sw & BCSR_SWITCHES_DIP_8) {
+ db1200_devs[0] = &db1200_i2c_dev;
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
+ printk(KERN_INFO " OTG port VBUS supply available!\n");
+ } else {
+ db1200_devs[0] = &db1200_spi_dev;
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
+
+ pfc |= (1 << 17); /* PSC0 owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
+ printk(KERN_INFO " OTG port VBUS supply disabled\n");
+ }
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+ * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+ */
+ sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+ if (sw == BCSR_SWITCHES_DIP_8) {
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+ db1200_audio_dev.name = "au1xpsc_i2s";
+ db1200_sound_dev.name = "db1200-i2s";
+ printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+ } else {
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+ db1200_audio_dev.name = "au1xpsc_ac97";
+ db1200_sound_dev.name = "db1200-ac97";
+ printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+ }
+
+ /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
+ /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
+ /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(64 << 20, 2, swapped);
+
+ return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+}
+device_initcall(db1200_dev_init);
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1200/Makefile b/arch/mips/alchemy/devboards/db1200/Makefile
deleted file mode 100644
index 17840a5..0000000
--- a/arch/mips/alchemy/devboards/db1200/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-y += setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1200/platform.c b/arch/mips/alchemy/devboards/db1200/platform.c
deleted file mode 100644
index c61867c..0000000
--- a/arch/mips/alchemy/devboards/db1200/platform.c
+++ /dev/null
@@ -1,648 +0,0 @@
-/*
- * DBAu1200 board platform device registration
- *
- * Copyright (C) 2008-2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/mmc/host.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-au1x00/au1550_spi.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-#include "../platform.h"
-
-static struct mtd_partition db1200_spiflash_parts[] = {
- {
- .name = "DB1200 SPI flash",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct flash_platform_data db1200_spiflash_data = {
- .name = "s25fl001",
- .parts = db1200_spiflash_parts,
- .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
- .type = "m25p10",
-};
-
-static struct spi_board_info db1200_spi_devs[] __initdata = {
- {
- /* TI TMP121AIDBVR temp sensor */
- .modalias = "tmp121",
- .max_speed_hz = 2000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = 0,
- },
- {
- /* Spansion S25FL001D0FMA SPI flash */
- .modalias = "m25p80",
- .max_speed_hz = 50000000,
- .bus_num = 0,
- .chip_select = 1,
- .mode = 0,
- .platform_data = &db1200_spiflash_data,
- },
-};
-
-static struct i2c_board_info db1200_i2c_devs[] __initdata = {
- {
- /* AT24C04-10 I2C eeprom */
- I2C_BOARD_INFO("24c04", 0x52),
- },
- {
- /* Philips NE1619 temp/voltage sensor (adm1025 drv) */
- I2C_BOARD_INFO("ne1619", 0x2d),
- },
- {
- /* I2S audio codec WM8731 */
- I2C_BOARD_INFO("wm8731", 0x1b),
- },
-};
-
-/**********************************************************************/
-
-static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
- unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
-
- ioaddr &= 0xffffff00;
-
- if (ctrl & NAND_CLE) {
- ioaddr += MEM_STNAND_CMD;
- } else if (ctrl & NAND_ALE) {
- ioaddr += MEM_STNAND_ADDR;
- } else {
- /* assume we want to r/w real data by default */
- ioaddr += MEM_STNAND_DATA;
- }
- this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
- if (cmd != NAND_CMD_NONE) {
- __raw_writeb(cmd, this->IO_ADDR_W);
- wmb();
- }
-}
-
-static int au1200_nand_device_ready(struct mtd_info *mtd)
-{
- return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
-}
-
-static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
-
-static struct mtd_partition db1200_nand_parts[] = {
- {
- .name = "NAND FS 0",
- .offset = 0,
- .size = 8 * 1024 * 1024,
- },
- {
- .name = "NAND FS 1",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL
- },
-};
-
-struct platform_nand_data db1200_nand_platdata = {
- .chip = {
- .nr_chips = 1,
- .chip_offset = 0,
- .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
- .partitions = db1200_nand_parts,
- .chip_delay = 20,
- .part_probe_types = db1200_part_probes,
- },
- .ctrl = {
- .dev_ready = au1200_nand_device_ready,
- .cmd_ctrl = au1200_nand_cmd_ctrl,
- },
-};
-
-static struct resource db1200_nand_res[] = {
- [0] = {
- .start = DB1200_NAND_PHYS_ADDR,
- .end = DB1200_NAND_PHYS_ADDR + 0xff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device db1200_nand_dev = {
- .name = "gen_nand",
- .num_resources = ARRAY_SIZE(db1200_nand_res),
- .resource = db1200_nand_res,
- .id = -1,
- .dev = {
- .platform_data = &db1200_nand_platdata,
- }
-};
-
-/**********************************************************************/
-
-static struct smc91x_platdata db1200_eth_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource db1200_eth_res[] = {
- [0] = {
- .start = DB1200_ETH_PHYS_ADDR,
- .end = DB1200_ETH_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DB1200_ETH_INT,
- .end = DB1200_ETH_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device db1200_eth_dev = {
- .dev = {
- .platform_data = &db1200_eth_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(db1200_eth_res),
- .resource = db1200_eth_res,
-};
-
-/**********************************************************************/
-
-static struct resource db1200_ide_res[] = {
- [0] = {
- .start = DB1200_IDE_PHYS_ADDR,
- .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DB1200_IDE_INT,
- .end = DB1200_IDE_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_ide_dev = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(db1200_ide_res),
- .resource = db1200_ide_res,
-};
-
-/**********************************************************************/
-
-static struct platform_device db1200_rtc_dev = {
- .name = "rtc-au1xxx",
- .id = -1,
-};
-
-/**********************************************************************/
-
-/* SD carddetects: they're supposed to be edge-triggered, but ack
- * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
- * is disabled and its counterpart enabled. The 500ms timeout is
- * because the carddetect isn't debounced in hardware.
- */
-static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
-{
- void(*mmc_cd)(struct mmc_host *, unsigned long);
-
- if (irq == DB1200_SD0_INSERT_INT) {
- disable_irq_nosync(DB1200_SD0_INSERT_INT);
- enable_irq(DB1200_SD0_EJECT_INT);
- } else {
- disable_irq_nosync(DB1200_SD0_EJECT_INT);
- enable_irq(DB1200_SD0_INSERT_INT);
- }
-
- /* link against CONFIG_MMC=m */
- mmc_cd = symbol_get(mmc_detect_change);
- if (mmc_cd) {
- mmc_cd(ptr, msecs_to_jiffies(500));
- symbol_put(mmc_detect_change);
- }
-
- return IRQ_HANDLED;
-}
-
-static int db1200_mmc_cd_setup(void *mmc_host, int en)
-{
- int ret;
-
- if (en) {
- ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
- IRQF_DISABLED, "sd_insert", mmc_host);
- if (ret)
- goto out;
-
- ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
- IRQF_DISABLED, "sd_eject", mmc_host);
- if (ret) {
- free_irq(DB1200_SD0_INSERT_INT, mmc_host);
- goto out;
- }
-
- if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
- enable_irq(DB1200_SD0_EJECT_INT);
- else
- enable_irq(DB1200_SD0_INSERT_INT);
-
- } else {
- free_irq(DB1200_SD0_INSERT_INT, mmc_host);
- free_irq(DB1200_SD0_EJECT_INT, mmc_host);
- }
- ret = 0;
-out:
- return ret;
-}
-
-static void db1200_mmc_set_power(void *mmc_host, int state)
-{
- if (state) {
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- msleep(400); /* stabilization time */
- } else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-}
-
-static int db1200_mmc_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int db1200_mmc_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void db1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- else
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
-}
-
-static struct led_classdev db1200_mmc_led = {
- .brightness_set = db1200_mmcled_set,
-};
-
-static struct au1xmmc_platform_data db1200mmc_platdata = {
- .cd_setup = db1200_mmc_cd_setup,
- .set_power = db1200_mmc_set_power,
- .card_inserted = db1200_mmc_card_inserted,
- .card_readonly = db1200_mmc_card_readonly,
- .led = &db1200_mmc_led,
-};
-
-static struct resource au1200_mmc0_resources[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200mmc_platdata,
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_resources),
- .resource = au1200_mmc0_resources,
-};
-
-/**********************************************************************/
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-/**********************************************************************/
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device db1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
-{
- if (cs)
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
- else
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
-}
-
-static struct au1550_spi_info db1200_spi_platdata = {
- .mainclk_hz = 50000000, /* PSC0 clock */
- .num_chipselect = 2,
- .activate_cs = db1200_spi_cs_en,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device db1200_spi_dev = {
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &db1200_spi_platdata,
- },
- .name = "au1550-spi",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static struct resource au1200_psc1_res[] = {
- [0] = {
- .start = AU1550_PSC1_PHYS_ADDR,
- .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC1_INT,
- .end = AU1200_PSC1_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC1_TX,
- .end = AU1200_DSCR_CMD0_PSC1_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC1_RX,
- .end = AU1200_DSCR_CMD0_PSC1_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-/* AC97 or I2S device */
-static struct platform_device db1200_audio_dev = {
- /* name assigned later based on switch setting */
- .id = 1, /* PSC ID */
- .num_resources = ARRAY_SIZE(au1200_psc1_res),
- .resource = au1200_psc1_res,
-};
-
-/* DB1200 ASoC card device */
-static struct platform_device db1200_sound_dev = {
- /* name assigned later based on switch setting */
- .id = 1, /* PSC ID */
-};
-
-static struct platform_device db1200_stac_dev = {
- .name = "ac97-codec",
- .id = 1, /* on PSC1 */
-};
-
-static struct platform_device db1200_audiodma_dev = {
- .name = "au1xpsc-pcm",
- .id = 1, /* PSC ID */
-};
-
-static struct platform_device *db1200_devs[] __initdata = {
- NULL, /* PSC0, selected by S6.8 */
- &db1200_ide_dev,
- &db1200_mmc0_dev,
- &au1200_lcd_dev,
- &db1200_eth_dev,
- &db1200_rtc_dev,
- &db1200_nand_dev,
- &db1200_audiodma_dev,
- &db1200_audio_dev,
- &db1200_stac_dev,
- &db1200_sound_dev,
-};
-
-static int __init db1200_dev_init(void)
-{
- unsigned long pfc;
- unsigned short sw;
- int swapped;
-
- i2c_register_board_info(0, db1200_i2c_devs,
- ARRAY_SIZE(db1200_i2c_devs));
- spi_register_board_info(db1200_spi_devs,
- ARRAY_SIZE(db1200_i2c_devs));
-
- /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
- * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
- */
-
- /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
- * this pin is claimed by PSC0 (unused though, but pinmux doesn't
- * allow to free it without crippling the SPI interface).
- * As a result, in SPI mode, OTG simply won't work (PSC0 uses
- * it as an input pin which is pulled high on the boards).
- */
- pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
-
- /* switch off OTG VBUS supply */
- gpio_request(215, "otg-vbus");
- gpio_direction_output(215, 1);
-
- printk(KERN_INFO "DB1200 device configuration:\n");
-
- sw = bcsr_read(BCSR_SWITCHES);
- if (sw & BCSR_SWITCHES_DIP_8) {
- db1200_devs[0] = &db1200_i2c_dev;
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
-
- printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
- printk(KERN_INFO " OTG port VBUS supply available!\n");
- } else {
- db1200_devs[0] = &db1200_spi_dev;
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
-
- pfc |= (1 << 17); /* PSC0 owns GPIO215 */
-
- printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
- printk(KERN_INFO " OTG port VBUS supply disabled\n");
- }
- __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
- wmb();
-
- /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
- * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
- */
- sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
- if (sw == BCSR_SWITCHES_DIP_8) {
- bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
- db1200_audio_dev.name = "au1xpsc_i2s";
- db1200_sound_dev.name = "db1200-i2s";
- printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
- } else {
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
- db1200_audio_dev.name = "au1xpsc_ac97";
- db1200_sound_dev.name = "db1200-ac97";
- printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
- }
-
- /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
- __raw_writel(PSC_SEL_CLK_SERCLK,
- (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
- wmb();
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
- /*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
- /*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(64 << 20, 2, swapped);
-
- return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
-}
-device_initcall(db1200_dev_init);
-
-/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/db1200/setup.c b/arch/mips/alchemy/devboards/db1200/setup.c
deleted file mode 100644
index 4a89800..0000000
--- a/arch/mips/alchemy/devboards/db1200/setup.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * Alchemy/AMD/RMI DB1200 board setup.
- *
- * Licensed under the terms outlined in the file COPYING in the root of
- * this source archive.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1200";
-}
-
-void __init board_setup(void)
-{
- unsigned long freq0, clksrc, div, pfc;
- unsigned short whoami;
-
- bcsr_init(DB1200_BCSR_PHYS_ADDR,
- DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
-
- whoami = bcsr_read(BCSR_WHOAMI);
- printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
- " Board-ID %d Daughtercard ID %d\n",
- (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
-
- /* SMBus/SPI on PSC0, Audio on PSC1 */
- pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
- pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
- pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
- __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
- wmb();
-
- /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
- * CPU clock; all other clock generators off/unused.
- */
- div = (get_au1x00_speed() + 25000000) / 50000000;
- if (div & 1)
- div++;
- div = ((div >> 1) - 1) & 0xff;
-
- freq0 = div << SYS_FC_FRDIV0_BIT;
- __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
- wmb();
- freq0 |= SYS_FC_FE0; /* enable F0 */
- __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
- wmb();
-
- /* psc0_intclk comes 1:1 from F0 */
- clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
- __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
- wmb();
-}
-
-static int __init db1200_arch_init(void)
-{
- /* GPIO7 is low-level triggered CPLD cascade */
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
-
- /* insert/eject pairs: one of both is always screaming. To avoid
- * issues they must not be automatically enabled when initially
- * requested.
- */
- irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
- irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
- return 0;
-}
-arch_initcall(db1200_arch_init);
diff --git a/arch/mips/alchemy/devboards/db1x00.c b/arch/mips/alchemy/devboards/db1x00.c
new file mode 100644
index 0000000..589ae24
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1x00.c
@@ -0,0 +1,256 @@
+/*
+ * DBAu1000/1500/1100 board support
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1000_dma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
+#include <prom.h>
+#include "platform.h"
+
+struct pci_dev;
+
+const char *get_system_type(void)
+{
+ return "Alchemy Db1x00";
+}
+
+void __init board_setup(void)
+{
+#ifdef CONFIG_MIPS_DB1000
+ printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1500
+ printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1100
+ printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+#endif
+ /* initialize board register space */
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
+ {
+ u32 pin_func;
+
+ /* Set IRFIRSEL instead of GPIO15 */
+ pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
+ au_writel(pin_func, SYS_PINFUNC);
+ /* Power off until the driver is in use */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
+ BCSR_RESETS_IRDA_MODE_OFF);
+ }
+#endif
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ /* Enable GPIO[31:0] inputs */
+ alchemy_gpio1_input_enable();
+}
+
+/* DB1xxx PCMCIA interrupt sources:
+ * CD0/1 GPIO0/3
+ * STSCHG0/1 GPIO1/4
+ * CARD0/1 GPIO2/5
+ */
+
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+#if defined(CONFIG_MIPS_DB1000)
+#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
+#elif defined(CONFIG_MIPS_DB1100)
+#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
+#elif defined(CONFIG_MIPS_DB1500)
+#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
+
+static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata db1500_pci_pd = {
+ .board_map_irq = db1500_map_pci_irq,
+};
+
+static struct platform_device db1500_pci_host_dev = {
+ .dev.platform_data = &db1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init db1500_pci_init(void)
+{
+ return platform_device_register(&db1500_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(db1500_pci_init);
+#endif
+
+#ifdef CONFIG_MIPS_DB1100
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+#endif
+
+static struct resource alchemy_ac97c_res[] = {
+ [0] = {
+ .start = AU1000_AC97_PHYS_ADDR,
+ .end = AU1000_AC97_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DMA_ID_AC97C_TX,
+ .end = DMA_ID_AC97C_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = DMA_ID_AC97C_RX,
+ .end = DMA_ID_AC97C_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device alchemy_ac97c_dev = {
+ .name = "alchemy-ac97c",
+ .id = -1,
+ .resource = alchemy_ac97c_res,
+ .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
+};
+
+static struct platform_device alchemy_ac97c_dma_dev = {
+ .name = "alchemy-pcm-dma",
+ .id = 0,
+};
+
+static struct platform_device db1x00_codec_dev = {
+ .name = "ac97-codec",
+ .id = -1,
+};
+
+static struct platform_device db1x00_audio_dev = {
+ .name = "db1000-audio",
+};
+
+static int __init db1xxx_dev_init(void)
+{
+ irq_set_irq_type(DB1XXX_PCMCIA_CD0, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(DB1XXX_PCMCIA_CD1, IRQ_TYPE_EDGE_BOTH);
+ irq_set_irq_type(DB1XXX_PCMCIA_CARD0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_CARD1, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_STSCHG0, IRQ_TYPE_LEVEL_LOW);
+ irq_set_irq_type(DB1XXX_PCMCIA_STSCHG1, IRQ_TYPE_LEVEL_LOW);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
+ /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
+ /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
+#ifdef CONFIG_MIPS_DB1100
+ platform_device_register(&au1100_lcd_device);
+#endif
+ platform_device_register(&db1x00_codec_dev);
+ platform_device_register(&alchemy_ac97c_dma_dev);
+ platform_device_register(&alchemy_ac97c_dev);
+ platform_device_register(&db1x00_audio_dev);
+
+ db1x_register_norflash(32 << 20, 4 /* 32bit */, F_SWAPPED);
+ return 0;
+}
+device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/db1x00/Makefile b/arch/mips/alchemy/devboards/db1x00/Makefile
deleted file mode 100644
index 613c0c0..0000000
--- a/arch/mips/alchemy/devboards/db1x00/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
deleted file mode 100644
index 2dbebcb..0000000
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ /dev/null
@@ -1,108 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Db1x00 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_eth.h>
-#include <asm/mach-db1x00/db1x00.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/reboot.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Db1x00";
-}
-
-
-void __init board_setup(void)
-{
-#ifdef CONFIG_MIPS_DB1000
- printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
- printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
- printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
-#endif
- /* initialize board register space */
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
-#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
- {
- u32 pin_func;
-
- /* Set IRFIRSEL instead of GPIO15 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
- au_writel(pin_func, SYS_PINFUNC);
- /* Power off until the driver is in use */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
- BCSR_RESETS_IRDA_MODE_OFF);
- }
-#endif
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- /* Enable GPIO[31:0] inputs */
- alchemy_gpio1_input_enable();
-}
-
-static int __init db1x00_init_irq(void)
-{
-#if defined(CONFIG_MIPS_DB1500)
- irq_set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1100)
- irq_set_irq_type(AU1100_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1100_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1100_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1100_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1100_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1100_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1000)
- irq_set_irq_type(AU1000_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1000_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
- irq_set_irq_type(AU1000_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
- irq_set_irq_type(AU1000_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
- irq_set_irq_type(AU1000_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1000_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#endif
- return 0;
-}
-arch_initcall(db1x00_init_irq);
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
deleted file mode 100644
index 67b36e8..0000000
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * DBAu1xxx board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1000_dma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include "../platform.h"
-
-struct pci_dev;
-
-/* DB1xxx PCMCIA interrupt sources:
- * CD0/1 GPIO0/3
- * STSCHG0/1 GPIO1/4
- * CARD0/1 GPIO2/5
- */
-
-#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
-
-#if defined(CONFIG_MIPS_DB1000)
-#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1100)
-#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
-#elif defined(CONFIG_MIPS_DB1500)
-#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
-#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
-#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
-#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
-#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
-#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
-
-static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata db1500_pci_pd = {
- .board_map_irq = db1500_map_pci_irq,
-};
-
-static struct platform_device db1500_pci_host_dev = {
- .dev.platform_data = &db1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init db1500_pci_init(void)
-{
- return platform_device_register(&db1500_pci_host_dev);
-}
-/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
-arch_initcall(db1500_pci_init);
-#endif
-
-#ifdef CONFIG_MIPS_DB1100
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-#endif
-
-static struct resource alchemy_ac97c_res[] = {
- [0] = {
- .start = AU1000_AC97_PHYS_ADDR,
- .end = AU1000_AC97_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = DMA_ID_AC97C_TX,
- .end = DMA_ID_AC97C_TX,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = DMA_ID_AC97C_RX,
- .end = DMA_ID_AC97C_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device alchemy_ac97c_dev = {
- .name = "alchemy-ac97c",
- .id = -1,
- .resource = alchemy_ac97c_res,
- .num_resources = ARRAY_SIZE(alchemy_ac97c_res),
-};
-
-static struct platform_device alchemy_ac97c_dma_dev = {
- .name = "alchemy-pcm-dma",
- .id = 0,
-};
-
-static struct platform_device db1x00_codec_dev = {
- .name = "ac97-codec",
- .id = -1,
-};
-
-static struct platform_device db1x00_audio_dev = {
- .name = "db1000-audio",
-};
-
-static int __init db1xxx_dev_init(void)
-{
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- DB1XXX_PCMCIA_CARD0, DB1XXX_PCMCIA_CD0,
- /*DB1XXX_PCMCIA_STSCHG0*/0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
- DB1XXX_PCMCIA_CARD1, DB1XXX_PCMCIA_CD1,
- /*DB1XXX_PCMCIA_STSCHG1*/0, 0, 1);
-#ifdef CONFIG_MIPS_DB1100
- platform_device_register(&au1100_lcd_device);
-#endif
- platform_device_register(&db1x00_codec_dev);
- platform_device_register(&alchemy_ac97c_dma_dev);
- platform_device_register(&alchemy_ac97c_dev);
- platform_device_register(&db1x00_audio_dev);
-
- db1x_register_norflash(0x02000000, 4 /* 32bit */, F_SWAPPED);
- return 0;
-}
-device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1100.c b/arch/mips/alchemy/devboards/pb1100.c
new file mode 100644
index 0000000..cff50d0
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1100.c
@@ -0,0 +1,167 @@
+/*
+ * Pb1100 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1100";
+}
+
+void __init board_setup(void)
+{
+ volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
+
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ alchemy_gpio1_input_enable();
+ udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ {
+ u32 pin_func, sys_freqctrl, sys_clksrc;
+
+ /* Configure pins GPIO[14:9] as GPIO */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* Zero and disable USBH/USBD/IrDA clock */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+
+ /* FREQ2 = aux / 2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+ SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48 MHz FREQ2 into USBH/USBD/IrDA
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ /* Setup the static bus controller */
+ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
+ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+ /*
+ * Get USB Functionality pin state (device vs host drive pins).
+ */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host. */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+ }
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled. */
+ if (!(readb(base + 0x28) & 0x20)) {
+ writeb(readb(base + 0x28) | 0x20, base + 0x28);
+ au_sync();
+ }
+ /* Put the clock in BCD mode. */
+ if (readb(base + 0x2C) & 0x4) { /* reg B */
+ writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
+ au_sync();
+ }
+}
+
+/******************************************************************************/
+
+static struct resource au1100_lcd_resources[] = {
+ [0] = {
+ .start = AU1100_LCD_PHYS_ADDR,
+ .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1100_LCD_INT,
+ .end = AU1100_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+ .name = "au1100-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1100_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1100_lcd_resources),
+ .resource = au1100_lcd_resources,
+};
+
+static int __init pb1100_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
+ irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
+ irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
+ irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
+
+ /* PCMCIA. single socket, identical to Pb1500 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
+ /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&au1100_lcd_device);
+
+ return 0;
+}
+device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1100/Makefile b/arch/mips/alchemy/devboards/pb1100/Makefile
deleted file mode 100644
index 7e3756c..0000000
--- a/arch/mips/alchemy/devboards/pb1100/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1100 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1100/board_setup.c b/arch/mips/alchemy/devboards/pb1100/board_setup.c
deleted file mode 100644
index d108fd5..0000000
--- a/arch/mips/alchemy/devboards/pb1100/board_setup.c
+++ /dev/null
@@ -1,127 +0,0 @@
-/*
- * Copyright 2002, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include <prom.h>
-
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1100";
-}
-
-void __init board_setup(void)
-{
- volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
-
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- {
- u32 pin_func, sys_freqctrl, sys_clksrc;
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD/IrDA clock */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
-
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48 MHz FREQ2 into USBH/USBD/IrDA
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Get USB Functionality pin state (device vs host drive pins).
- */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host. */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
- }
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled. */
- if (!(readb(base + 0x28) & 0x20)) {
- writeb(readb(base + 0x28) | 0x20, base + 0x28);
- au_sync();
- }
- /* Put the clock in BCD mode. */
- if (readb(base + 0x2C) & 0x4) { /* reg B */
- writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
- au_sync();
- }
-}
-
-static int __init pb1100_init_irq(void)
-{
- irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
- irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
- irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
- irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
-
- return 0;
-}
-arch_initcall(pb1100_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1100/platform.c b/arch/mips/alchemy/devboards/pb1100/platform.c
deleted file mode 100644
index 9c57c01..0000000
--- a/arch/mips/alchemy/devboards/pb1100/platform.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * Pb1100 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/init.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static struct resource au1100_lcd_resources[] = {
- [0] = {
- .start = AU1100_LCD_PHYS_ADDR,
- .end = AU1100_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1100_LCD_INT,
- .end = AU1100_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1100_lcd_device = {
- .name = "au1100-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1100_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1100_lcd_resources),
- .resource = au1100_lcd_resources,
-};
-
-static int __init pb1100_dev_init(void)
-{
- int swapped;
-
- /* PCMCIA. single socket, identical to Pb1500 */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1100_GPIO11_INT, AU1100_GPIO9_INT, /* card / insert */
- /*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
- db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
- platform_device_register(&au1100_lcd_device);
-
- return 0;
-}
-device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1200.c b/arch/mips/alchemy/devboards/pb1200.c
new file mode 100644
index 0000000..a1b6497
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1200.c
@@ -0,0 +1,464 @@
+/*
+ * Pb1200/DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/leds.h>
+#include <linux/platform_device.h>
+#include <linux/smc91x.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-pb1x00/pb1200.h>
+#include <prom.h>
+#include "platform.h"
+
+
+const char *get_system_type(void)
+{
+ return "PB1200";
+}
+
+void __init board_setup(void)
+{
+ printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+ bcsr_init(PB1200_BCSR_PHYS_ADDR,
+ PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
+
+#if 0
+ {
+ u32 pin_func;
+
+ /*
+ * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
+ au_sync();
+ }
+#endif
+
+#if defined(CONFIG_I2C_AU1550)
+ {
+ u32 freq0, clksrc;
+ u32 pin_func;
+
+ /* Select SMBus in CPLD */
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ /* Set GPIOs correctly */
+ pin_func |= 2 << 17;
+ au_writel(pin_func, SYS_PINFUNC);
+ au_sync();
+
+ /* The I2C driver depends on 50 MHz clock */
+ freq0 = au_readl(SYS_FREQCTRL0);
+ au_sync();
+ freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+ freq0 |= 3 << SYS_FC_FRDIV1_BIT;
+ /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+ freq0 |= SYS_FC_FE1;
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+
+ clksrc = au_readl(SYS_CLKSRC);
+ au_sync();
+ clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
+ /* Bit 22 is EXTCLK0 for PSC0 */
+ clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
+ au_writel(clksrc, SYS_CLKSRC);
+ au_sync();
+ }
+#endif
+
+ /*
+ * The Pb1200 development board uses external MUX for PSC0 to
+ * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
+ */
+#ifdef CONFIG_I2C_AU1550
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+#endif
+ au_sync();
+}
+
+/******************************************************************************/
+
+static int mmc_activity;
+
+static void pb1200mmc0_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+
+ msleep(1);
+}
+
+static int pb1200mmc0_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int pb1200mmc0_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void pb1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF) {
+ if (++mmc_activity == 1)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ } else {
+ if (--mmc_activity == 0)
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+ }
+}
+
+static struct led_classdev pb1200mmc_led = {
+ .brightness_set = pb1200_mmcled_set,
+};
+
+static void pb1200mmc1_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
+ else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
+
+ msleep(1);
+}
+
+static int pb1200mmc1_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
+}
+
+static int pb1200mmc1_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
+}
+
+static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
+ [0] = {
+ .set_power = pb1200mmc0_set_power,
+ .card_inserted = pb1200mmc0_card_inserted,
+ .card_readonly = pb1200mmc0_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+ [1] = {
+ .set_power = pb1200mmc1_set_power,
+ .card_inserted = pb1200mmc1_card_inserted,
+ .card_readonly = pb1200mmc1_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+};
+
+static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
+
+static struct resource au1200_mmc0_res[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX0,
+ .end = AU1200_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX0,
+ .end = AU1200_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc0_dev = {
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200mmc_platdata[0],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc0_res),
+ .resource = au1200_mmc0_res,
+};
+
+static struct resource au1200_mmc1_res[] = {
+ [0] = {
+ .start = AU1100_SD1_PHYS_ADDR,
+ .end = AU1100_SD1_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_SD_INT,
+ .end = AU1200_SD_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_SDMS_TX1,
+ .end = AU1200_DSCR_CMD0_SDMS_TX1,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_SDMS_RX1,
+ .end = AU1200_DSCR_CMD0_SDMS_RX1,
+ .flags = IORESOURCE_DMA,
+ }
+};
+
+static struct platform_device pb1200_mmc1_dev = {
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &au1xxx_mmc_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &pb1200mmc_platdata[1],
+ },
+ .num_resources = ARRAY_SIZE(au1200_mmc1_res),
+ .resource = au1200_mmc1_res,
+};
+
+
+static struct resource ide_resources[] = {
+ [0] = {
+ .start = IDE_PHYS_ADDR,
+ .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = IDE_INT,
+ .end = IDE_INT,
+ .flags = IORESOURCE_IRQ
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_DMA_REQ1,
+ .end = AU1200_DSCR_CMD0_DMA_REQ1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static u64 au1200_ide_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device ide_device = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_ide_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(ide_resources),
+ .resource = ide_resources
+};
+
+static struct smc91x_platdata smc_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91c111_resources[] = {
+ [0] = {
+ .name = "smc91x-regs",
+ .start = SMC91C111_PHYS_ADDR,
+ .end = SMC91C111_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = SMC91C111_INT,
+ .end = SMC91C111_INT,
+ .flags = IORESOURCE_IRQ
+ },
+};
+
+static struct platform_device smc91c111_device = {
+ .dev = {
+ .platform_data = &smc_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91c111_resources),
+ .resource = smc91c111_resources
+};
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = AU1550_PSC0_PHYS_ADDR,
+ .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1200_DSCR_CMD0_PSC0_TX,
+ .end = AU1200_DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1200_DSCR_CMD0_PSC0_RX,
+ .end = AU1200_DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device pb1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_LCD_INT,
+ .end = AU1200_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1200_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1200_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1200_lcd_res),
+ .resource = au1200_lcd_res,
+};
+
+static struct platform_device *board_platform_devices[] __initdata = {
+ &ide_device,
+ &smc91c111_device,
+ &pb1200_i2c_dev,
+ &pb1200_mmc0_dev,
+ &pb1200_mmc1_dev,
+ &au1200_lcd_dev,
+};
+
+static int __init board_register_devices(void)
+{
+ int swapped;
+
+ /* We have a problem with CPLD rev 3. */
+ if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+ printk(KERN_ERR "updated to latest revision. This software will\n");
+ printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ panic("Game over. Your score is 0.");
+ }
+
+ irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
+ /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
+ /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
+
+ return platform_add_devices(board_platform_devices,
+ ARRAY_SIZE(board_platform_devices));
+}
+device_initcall(board_register_devices);
+
+
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/pb1200/Makefile b/arch/mips/alchemy/devboards/pb1200/Makefile
deleted file mode 100644
index 18c1bd5..0000000
--- a/arch/mips/alchemy/devboards/pb1200/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1200/board_setup.c b/arch/mips/alchemy/devboards/pb1200/board_setup.c
deleted file mode 100644
index 6d06b07..0000000
--- a/arch/mips/alchemy/devboards/pb1200/board_setup.c
+++ /dev/null
@@ -1,174 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1200/Db1200 board setup.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1200";
-}
-
-void __init board_setup(void)
-{
- printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
- bcsr_init(PB1200_BCSR_PHYS_ADDR,
- PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
-
-#if 0
- {
- u32 pin_func;
-
- /*
- * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
- }
-#endif
-
-#if defined(CONFIG_I2C_AU1550)
- {
- u32 freq0, clksrc;
- u32 pin_func;
-
- /* Select SMBus in CPLD */
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- /* Set GPIOs correctly */
- pin_func |= 2 << 17;
- au_writel(pin_func, SYS_PINFUNC);
- au_sync();
-
- /* The I2C driver depends on 50 MHz clock */
- freq0 = au_readl(SYS_FREQCTRL0);
- au_sync();
- freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
- freq0 |= 3 << SYS_FC_FRDIV1_BIT;
- /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
- freq0 |= SYS_FC_FE1;
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
-
- clksrc = au_readl(SYS_CLKSRC);
- au_sync();
- clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
- /* Bit 22 is EXTCLK0 for PSC0 */
- clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
- au_writel(clksrc, SYS_CLKSRC);
- au_sync();
- }
-#endif
-
- /*
- * The Pb1200 development board uses external MUX for PSC0 to
- * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
- */
-#ifdef CONFIG_I2C_AU1550
- bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
-#endif
- au_sync();
-}
-
-static int __init pb1200_init_irq(void)
-{
- /* We have a problem with CPLD rev 3. */
- if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-
- irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
- bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
-
- return 0;
-}
-arch_initcall(pb1200_init_irq);
-
-
-int board_au1200fb_panel(void)
-{
- return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- /* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL, 0);
- /* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
- return 0;
-}
diff --git a/arch/mips/alchemy/devboards/pb1200/platform.c b/arch/mips/alchemy/devboards/pb1200/platform.c
deleted file mode 100644
index 54f7f7b..0000000
--- a/arch/mips/alchemy/devboards/pb1200/platform.c
+++ /dev/null
@@ -1,339 +0,0 @@
-/*
- * Pb1200/DBAu1200 board platform device registration
- *
- * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1100_mmc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-pb1x00/pb1200.h>
-
-#include "../platform.h"
-
-static int mmc_activity;
-
-static void pb1200mmc0_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc0_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int pb1200mmc0_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void pb1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF) {
- if (++mmc_activity == 1)
- bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
- } else {
- if (--mmc_activity == 0)
- bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
- }
-}
-
-static struct led_classdev pb1200mmc_led = {
- .brightness_set = pb1200_mmcled_set,
-};
-
-static void pb1200mmc1_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
- else
- bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
-
- msleep(1);
-}
-
-static int pb1200mmc1_card_readonly(void *mmc_host)
-{
- return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
-}
-
-static int pb1200mmc1_card_inserted(void *mmc_host)
-{
- return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
-}
-
-static struct au1xmmc_platform_data pb1200mmc_platdata[2] = {
- [0] = {
- .set_power = pb1200mmc0_set_power,
- .card_inserted = pb1200mmc0_card_inserted,
- .card_readonly = pb1200mmc0_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
- [1] = {
- .set_power = pb1200mmc1_set_power,
- .card_inserted = pb1200mmc1_card_inserted,
- .card_readonly = pb1200mmc1_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
-};
-
-static u64 au1xxx_mmc_dmamask = DMA_BIT_MASK(32);
-
-static struct resource au1200_mmc0_res[] = {
- [0] = {
- .start = AU1100_SD0_PHYS_ADDR,
- .end = AU1100_SD0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX0,
- .end = AU1200_DSCR_CMD0_SDMS_TX0,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX0,
- .end = AU1200_DSCR_CMD0_SDMS_RX0,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc0_dev = {
- .name = "au1xxx-mmc",
- .id = 0,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[0],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc0_res),
- .resource = au1200_mmc0_res,
-};
-
-static struct resource au1200_mmc1_res[] = {
- [0] = {
- .start = AU1100_SD1_PHYS_ADDR,
- .end = AU1100_SD1_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_SD_INT,
- .end = AU1200_SD_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_SDMS_TX1,
- .end = AU1200_DSCR_CMD0_SDMS_TX1,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_SDMS_RX1,
- .end = AU1200_DSCR_CMD0_SDMS_RX1,
- .flags = IORESOURCE_DMA,
- }
-};
-
-static struct platform_device pb1200_mmc1_dev = {
- .name = "au1xxx-mmc",
- .id = 1,
- .dev = {
- .dma_mask = &au1xxx_mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &pb1200mmc_platdata[1],
- },
- .num_resources = ARRAY_SIZE(au1200_mmc1_res),
- .resource = au1200_mmc1_res,
-};
-
-
-static struct resource ide_resources[] = {
- [0] = {
- .start = IDE_PHYS_ADDR,
- .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = IDE_INT,
- .end = IDE_INT,
- .flags = IORESOURCE_IRQ
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_DMA_REQ1,
- .end = AU1200_DSCR_CMD0_DMA_REQ1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static u64 ide_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device ide_device = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(ide_resources),
- .resource = ide_resources
-};
-
-static struct smc91x_platdata smc_data = {
- .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91c111_resources[] = {
- [0] = {
- .name = "smc91x-regs",
- .start = SMC91C111_PHYS_ADDR,
- .end = SMC91C111_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = SMC91C111_INT,
- .end = SMC91C111_INT,
- .flags = IORESOURCE_IRQ
- },
-};
-
-static struct platform_device smc91c111_device = {
- .dev = {
- .platform_data = &smc_data,
- },
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smc91c111_resources),
- .resource = smc91c111_resources
-};
-
-static struct resource au1200_psc0_res[] = {
- [0] = {
- .start = AU1550_PSC0_PHYS_ADDR,
- .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_PSC0_INT,
- .end = AU1200_PSC0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1200_DSCR_CMD0_PSC0_TX,
- .end = AU1200_DSCR_CMD0_PSC0_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1200_DSCR_CMD0_PSC0_RX,
- .end = AU1200_DSCR_CMD0_PSC0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1200_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1200_psc0_res),
- .resource = au1200_psc0_res,
-};
-
-static struct resource au1200_lcd_res[] = {
- [0] = {
- .start = AU1200_LCD_PHYS_ADDR,
- .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1200_LCD_INT,
- .end = AU1200_LCD_INT,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 au1200_lcd_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device au1200_lcd_dev = {
- .name = "au1200-lcd",
- .id = 0,
- .dev = {
- .dma_mask = &au1200_lcd_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(au1200_lcd_res),
- .resource = au1200_lcd_res,
-};
-
-static struct platform_device *board_platform_devices[] __initdata = {
- &ide_device,
- &smc91c111_device,
- &pb1200_i2c_dev,
- &pb1200_mmc0_dev,
- &pb1200_mmc1_dev,
- &au1200_lcd_dev,
-};
-
-static int __init board_register_devices(void)
-{
- int swapped;
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- PB1200_PC0_INT, PB1200_PC0_INSERT_INT,
- /*PB1200_PC0_STSCHG_INT*/0, PB1200_PC0_EJECT_INT, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- PB1200_PC1_INT, PB1200_PC1_INSERT_INT,
- /*PB1200_PC1_STSCHG_INT*/0, PB1200_PC1_EJECT_INT, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
-
- return platform_add_devices(board_platform_devices,
- ARRAY_SIZE(board_platform_devices));
-}
-device_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/devboards/pb1500.c b/arch/mips/alchemy/devboards/pb1500.c
new file mode 100644
index 0000000..e7b807b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1500.c
@@ -0,0 +1,198 @@
+/*
+ * Pb1500 board support.
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1500";
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+ u32 sys_freqctrl, sys_clksrc;
+
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+ sys_clksrc = sys_freqctrl = pin_func = 0;
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ alchemy_gpio1_input_enable();
+ udelay(100);
+
+ /* GPIO201 is input for PCMCIA card detect */
+ /* GPIO203 is input for PCMCIA interrupt request */
+ alchemy_gpio_direction_input(201);
+ alchemy_gpio_direction_input(203);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* zero and disable USBH/USBD clocks */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+
+ /* FREQ2 = aux/2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48MHz FREQ2 into USB Host and/or Device
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+#ifdef CONFIG_PCI
+ {
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
+ /* Setup PCI bus controller */
+ __raw_writel(0x00003fff, base + PCI_REG_CMEM);
+ __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
+ __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
+ __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
+ __raw_writel(0x00003c04, base + PCI_REG_PARAM);
+ __raw_writel(0x00000008, base + PCI_REG_MBAR);
+ wmb();
+ }
+#endif
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled */
+ if (!(au_readl(0xac000028) & 0x20)) {
+ printk(KERN_INFO "enabling clock ...\n");
+ au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
+ }
+ /* Put the clock in BCD mode */
+ if (au_readl(0xac00002c) & 0x4) { /* reg B */
+ au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
+ au_sync();
+ }
+}
+
+/******************************************************************************/
+
+static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1500_pci_pd = {
+ .board_map_irq = pb1500_map_pci_irq,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device pb1500_pci_host = {
+ .dev.platform_data = &pb1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init pb1500_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
+ irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+ irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+ /* PCMCIA. single socket, identical to Pb1100 */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
+ /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1500_pci_host);
+
+ return 0;
+}
+arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1500/Makefile b/arch/mips/alchemy/devboards/pb1500/Makefile
deleted file mode 100644
index e83b151..0000000
--- a/arch/mips/alchemy/devboards/pb1500/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1500 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1500/board_setup.c b/arch/mips/alchemy/devboards/pb1500/board_setup.c
deleted file mode 100644
index 37c1883..0000000
--- a/arch/mips/alchemy/devboards/pb1500/board_setup.c
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1500";
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
- u32 sys_freqctrl, sys_clksrc;
-
- bcsr_init(DB1000_BCSR_PHYS_ADDR,
- DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
-
- sys_clksrc = sys_freqctrl = pin_func = 0;
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
- /* GPIO201 is input for PCMCIA card detect */
- /* GPIO203 is input for PCMCIA interrupt request */
- alchemy_gpio_direction_input(201);
- alchemy_gpio_direction_input(203);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- /* FREQ2 = aux/2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
-#ifdef CONFIG_PCI
- {
- void __iomem *base =
- (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
- /* Setup PCI bus controller */
- __raw_writel(0x00003fff, base + PCI_REG_CMEM);
- __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
- __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
- __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
- __raw_writel(0x00003c04, base + PCI_REG_PARAM);
- __raw_writel(0x00000008, base + PCI_REG_MBAR);
- wmb();
- }
-#endif
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled */
- if (!(au_readl(0xac000028) & 0x20)) {
- printk(KERN_INFO "enabling clock ...\n");
- au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
- }
- /* Put the clock in BCD mode */
- if (au_readl(0xac00002c) & 0x4) { /* reg B */
- au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
- au_sync();
- }
-}
-
-static int __init pb1500_init_irq(void)
-{
- irq_set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
- irq_set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
- irq_set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
- irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
- irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
-
- return 0;
-}
-arch_initcall(pb1500_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
deleted file mode 100644
index 1e52a01..0000000
--- a/arch/mips/alchemy/devboards/pb1500/platform.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * Pb1500 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12)
- return (pin == 1) ? AU1500_PCI_INTA : 0xff;
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata pb1500_pci_pd = {
- .board_map_irq = pb1500_map_pci_irq,
- .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
- PCI_CONFIG_CH |
-#if defined(__MIPSEB__)
- PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
-#else
- 0,
-#endif
-};
-
-static struct platform_device pb1500_pci_host = {
- .dev.platform_data = &pb1500_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static int __init pb1500_dev_init(void)
-{
- int swapped;
-
- /* PCMCIA. single socket, identical to Pb1100 */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1500_GPIO11_INT, AU1500_GPIO9_INT, /* card / insert */
- /*AU1500_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
- db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
- platform_device_register(&pb1500_pci_host);
-
- return 0;
-}
-arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550.c b/arch/mips/alchemy/devboards/pb1550.c
new file mode 100644
index 0000000..e4a00a5
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1550.c
@@ -0,0 +1,178 @@
+/*
+ * Pb1550 board support.
+ *
+ * Copyright (C) 2009-2011 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/gpio.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+ return "PB1550";
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+
+ bcsr_init(PB1550_BCSR_PHYS_ADDR,
+ PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+
+ alchemy_gpio2_enable();
+
+ /*
+ * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
+
+ printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
+}
+
+/******************************************************************************/
+
+static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTB;
+ case 2: return AU1500_PCI_INTC;
+ case 3: return AU1500_PCI_INTD;
+ case 4: return AU1500_PCI_INTA;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1550_pci_pd = {
+ .board_map_irq = pb1550_map_pci_irq,
+};
+
+static struct platform_device pb1550_pci_host = {
+ .dev.platform_data = &pb1550_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static struct resource au1550_psc2_res[] = {
+ [0] = {
+ .start = AU1550_PSC2_PHYS_ADDR,
+ .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1550_PSC2_INT,
+ .end = AU1550_PSC2_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1550_DSCR_CMD0_PSC2_TX,
+ .end = AU1550_DSCR_CMD0_PSC2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1550_DSCR_CMD0_PSC2_RX,
+ .end = AU1550_DSCR_CMD0_PSC2_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device pb1550_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1550_psc2_res),
+ .resource = au1550_psc2_res,
+};
+
+static int __init pb1550_dev_init(void)
+{
+ int swapped;
+
+ irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
+ irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
+
+ /* enable both PCMCIA card irqs in the shared line */
+ alchemy_gpio2_enable_int(201);
+ alchemy_gpio2_enable_int(202);
+
+ /* Pb1550, like all others, also has statuschange irqs; however they're
+ * wired up on one of the Au1550's shared GPIO201_205 line, which also
+ * services the PCMCIA card interrupts. So we ignore statuschange and
+ * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+ * drivers are used to shared irqs and b) statuschange isn't really use-
+ * ful anyway.
+ */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
+
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1550_pci_host);
+ platform_device_register(&pb1550_i2c_dev);
+
+ return 0;
+}
+arch_initcall(pb1550_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550/Makefile b/arch/mips/alchemy/devboards/pb1550/Makefile
deleted file mode 100644
index 9661b6e..0000000
--- a/arch/mips/alchemy/devboards/pb1550/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1550 board.
-#
-
-obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1550/board_setup.c b/arch/mips/alchemy/devboards/pb1550/board_setup.c
deleted file mode 100644
index 0f62d1e..0000000
--- a/arch/mips/alchemy/devboards/pb1550/board_setup.c
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1550 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-au1x00/gpio.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1550";
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
-
- bcsr_init(PB1550_BCSR_PHYS_ADDR,
- PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
-
- alchemy_gpio2_enable();
-
- /*
- * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
-
- printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
-}
-
-static int __init pb1550_init_irq(void)
-{
- irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
- irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
-
- /* enable both PCMCIA card irqs in the shared line */
- alchemy_gpio2_enable_int(201);
- alchemy_gpio2_enable_int(202);
-
- return 0;
-}
-arch_initcall(pb1550_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
deleted file mode 100644
index a4604b8..0000000
--- a/arch/mips/alchemy/devboards/pb1550/platform.c
+++ /dev/null
@@ -1,140 +0,0 @@
-/*
- * Pb1550 board platform device registration
- *
- * Copyright (C) 2009 Manuel Lauss
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <asm/mach-db1x00/bcsr.h>
-
-#include "../platform.h"
-
-static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
-{
- if ((slot < 12) || (slot > 13) || pin == 0)
- return -1;
- if (slot == 12) {
- switch (pin) {
- case 1: return AU1500_PCI_INTB;
- case 2: return AU1500_PCI_INTC;
- case 3: return AU1500_PCI_INTD;
- case 4: return AU1500_PCI_INTA;
- }
- }
- if (slot == 13) {
- switch (pin) {
- case 1: return AU1500_PCI_INTA;
- case 2: return AU1500_PCI_INTB;
- case 3: return AU1500_PCI_INTC;
- case 4: return AU1500_PCI_INTD;
- }
- }
- return -1;
-}
-
-static struct resource alchemy_pci_host_res[] = {
- [0] = {
- .start = AU1500_PCI_PHYS_ADDR,
- .end = AU1500_PCI_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct alchemy_pci_platdata pb1550_pci_pd = {
- .board_map_irq = pb1550_map_pci_irq,
-};
-
-static struct platform_device pb1550_pci_host = {
- .dev.platform_data = &pb1550_pci_pd,
- .name = "alchemy-pci",
- .id = 0,
- .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
- .resource = alchemy_pci_host_res,
-};
-
-static struct resource au1550_psc2_res[] = {
- [0] = {
- .start = AU1550_PSC2_PHYS_ADDR,
- .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AU1550_PSC2_INT,
- .end = AU1550_PSC2_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = AU1550_DSCR_CMD0_PSC2_TX,
- .end = AU1550_DSCR_CMD0_PSC2_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = AU1550_DSCR_CMD0_PSC2_RX,
- .end = AU1550_DSCR_CMD0_PSC2_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device pb1550_i2c_dev = {
- .name = "au1xpsc_smbus",
- .id = 0, /* bus number */
- .num_resources = ARRAY_SIZE(au1550_psc2_res),
- .resource = au1550_psc2_res,
-};
-
-static int __init pb1550_dev_init(void)
-{
- int swapped;
-
- /* Pb1550, like all others, also has statuschange irqs; however they're
- * wired up on one of the Au1550's shared GPIO201_205 line, which also
- * services the PCMCIA card interrupts. So we ignore statuschange and
- * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
- * drivers are used to shared irqs and b) statuschange isn't really use-
- * ful anyway.
- */
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
- AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
-
- db1x_register_pcmcia_socket(
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
- AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
- AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
-
- swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
- db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
- platform_device_register(&pb1550_pci_host);
- platform_device_register(&pb1550_i2c_dev);
-
- return 0;
-}
-arch_initcall(pb1550_dev_init);
--
1.7.7.1
^ permalink raw reply related [flat|nested] 46+ messages in thread
* Re: [PATCH RESEND 01/18] MIPS: Alchemy: remove PB1000 support
2011-11-02 11:53 ` [PATCH RESEND " Manuel Lauss
@ 2011-11-09 14:48 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:48 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS, netdev, linux-pcmcia
On Wed, Nov 02, 2011 at 12:53:44PM +0100, Manuel Lauss wrote:
> Noone seems to have test hardware or care anymore. Drop PB1000 support
> and along with it the old Alchemy PCMCIA socket driver.
Nobody (n)acked so I queued this one for 3.3.
Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support
2011-11-01 19:03 ` [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support Manuel Lauss
@ 2011-11-09 14:49 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:49 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
On Tue, Nov 01, 2011 at 08:03:28PM +0100, Manuel Lauss wrote:
> No test hardware and no (apparent) users. These boards seem very
> similar to the DB1500, so if required support can be brought back
> again (I have datasheets) but then with dedicated board code, not
> tacked on to DB1000 support.
Experience says reaction is always a release after the feature removal ;)
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 03/18] MIPS: Alchemy: devboards: remove unneeded BCSR IRQ reg acc
2011-11-01 19:03 ` [PATCH 03/18] MIPS: Alchemy: devboards: remove unneeded BCSR IRQ reg acc Manuel Lauss
@ 2011-11-09 14:49 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:49 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 04/18] MIPS: Alchemy: Au1300 SoC support
2011-11-01 19:03 ` [PATCH 04/18] MIPS: Alchemy: Au1300 SoC support Manuel Lauss
@ 2011-11-09 14:50 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:50 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 05/18] MIPS: Alchemy: DB1300 support
2011-11-01 19:03 ` [PATCH 05/18] MIPS: Alchemy: DB1300 support Manuel Lauss
@ 2011-11-09 14:50 ` Ralf Baechle
2011-11-09 18:38 ` [PATCH] MIPS: Alchemy: db1300: fix build: missing module.h Manuel Lauss
0 siblings, 1 reply; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:50 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 06/18] MIPS: Alchemy: better DB1550 support
2011-11-01 19:03 ` [PATCH 06/18] MIPS: Alchemy: better DB1550 support Manuel Lauss
@ 2011-11-09 14:50 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:50 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 07/18] MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files
2011-11-01 19:03 ` [PATCH 07/18] MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files Manuel Lauss
@ 2011-11-09 14:50 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:50 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH v2 08/18] MIPS: Alchemy: merge devboard code into single per-board files.
2011-11-04 8:35 ` [PATCH v2 " Manuel Lauss
@ 2011-11-09 14:50 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:50 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 09/18] MIPS: Alchemy: move au1200fb global functions to platform data
2011-11-01 19:03 ` Manuel Lauss
@ 2011-11-09 14:52 ` Ralf Baechle
-1 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:52 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS, linux-fbdev
No (n)ack or comments received, so I've queued this for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 09/18] MIPS: Alchemy: move au1200fb global functions to
@ 2011-11-09 14:52 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:52 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS, linux-fbdev
No (n)ack or comments received, so I've queued this for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 10/18] MIPS: Alchemy: Merge PB1200 support into DB1200 code.
2011-11-01 19:03 ` [PATCH 10/18] MIPS: Alchemy: Merge PB1200 support into DB1200 code Manuel Lauss
@ 2011-11-09 14:52 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:52 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 11/18] MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100
2011-11-01 19:03 ` [PATCH 11/18] MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100 Manuel Lauss
@ 2011-11-09 14:53 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:53 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 12/18] MIPS: Alchemy: MMC for DB1100
2011-11-01 19:03 ` [PATCH 12/18] MIPS: Alchemy: MMC for DB1100 Manuel Lauss
@ 2011-11-09 14:53 ` Ralf Baechle
2011-11-09 18:39 ` [PATCH] MIPS: Alchemy: db1100: fix build: missing module.h Manuel Lauss
0 siblings, 1 reply; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:53 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 13/18] MIPS: Alchemy: add RTC device to all devboards
2011-11-01 19:03 ` [PATCH 13/18] MIPS: Alchemy: add RTC device to all devboards Manuel Lauss
@ 2011-11-09 14:53 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:53 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 14/18] MTD: nand: make au1550nd.c a platform_driver
2011-11-01 19:03 ` [PATCH 14/18] MTD: nand: make au1550nd.c a platform_driver Manuel Lauss
@ 2011-11-09 14:54 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:54 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS, linux-mtd
On Tue, Nov 01, 2011 at 08:03:40PM +0100, Manuel Lauss wrote:
> Transform the au1550nd.c driver into a platform_driver and hook it
> up in the PB1550 board (gen_nand works fine on the DB1550, but since
> I don't have a PB1550 to test this driver stays for now).
>
> Cc: linux-mtd@lists.infradead.org
> Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
> ---
> Tested on the DB1550 as well.
> I'd like for this to go in via the MIPS tree if at all possible.
No (n)acks or comments received, so queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 15/18] MIPS: Alchemy: remove unused board headers
2011-11-01 19:03 ` [PATCH 15/18] MIPS: Alchemy: remove unused board headers Manuel Lauss
@ 2011-11-09 14:55 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:55 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 16/18] net/irda: convert au1k_ir to platform driver.
2011-11-01 19:03 ` [PATCH 16/18] net/irda: convert au1k_ir to platform driver Manuel Lauss
@ 2011-11-09 14:55 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:55 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS, Samuel Ortiz, netdev
On Tue, Nov 01, 2011 at 08:03:42PM +0100, Manuel Lauss wrote:
> Moderate driver cleanup:
> convert to platform driver, get rid of board-specific code.
>
> Driver loads and runs on a DB1100 board. But since I have no other
> IrDA hardware to exchange data with I can't say whether it really sends
> and receives.
>
> Cc: Samuel Ortiz <samuel@sortiz.org>
> Cc: netdev@vger.kernel.org
> Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
> ---
> I'd like for this to go in via the MIPS tree since other mips patches depend
> on it.
No (n)acks or comments received so queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 17/18] MIPS: Alchemy: hook up IrDA on DB1000/DB1100
2011-11-01 19:03 ` [PATCH 17/18] MIPS: Alchemy: hook up IrDA on DB1000/DB1100 Manuel Lauss
@ 2011-11-09 14:56 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:56 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH 18/18] MIPS: Alchemy: Touchscreen support on DB1100
2011-11-01 19:03 ` [PATCH 18/18] MIPS: Alchemy: Touchscreen support on DB1100 Manuel Lauss
@ 2011-11-09 14:56 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 14:56 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Queued for 3.3. Thanks,
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* [PATCH] MIPS: Alchemy: db1300: fix build: missing module.h
2011-11-09 14:50 ` Ralf Baechle
@ 2011-11-09 18:38 ` Manuel Lauss
2011-11-09 18:48 ` Ralf Baechle
0 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-09 18:38 UTC (permalink / raw)
To: Ralf Baechle; +Cc: Linux-MIPS, Manuel Lauss
add module.h to fix build (symbol_get/symbol_put) against 3.2-rc1
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
Please fold into "[PATCH 05/18] Basic support for the DB1300 board."
arch/mips/alchemy/devboards/db1300.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
index 23fd4ff..0893f2a 100644
--- a/arch/mips/alchemy/devboards/db1300.c
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -14,6 +14,7 @@
#include <linux/leds.h>
#include <linux/ata_platform.h>
#include <linux/mmc/host.h>
+#include <linux/module.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
--
1.7.7.2
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH] MIPS: Alchemy: db1100: fix build: missing module.h
2011-11-09 14:53 ` Ralf Baechle
@ 2011-11-09 18:39 ` Manuel Lauss
2011-11-09 18:55 ` Ralf Baechle
0 siblings, 1 reply; 46+ messages in thread
From: Manuel Lauss @ 2011-11-09 18:39 UTC (permalink / raw)
To: Ralf Baechle; +Cc: Linux-MIPS, Manuel Lauss
fix build against 3.2-rc1, add a missing module.h (symbol_get/symbol_put).
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
---
Please fold into "[PATCH 12/18] MIPS: Alchemy: MMC for DB1100".
arch/mips/alchemy/devboards/db1000.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c
index e110f6d..1b81dbf 100644
--- a/arch/mips/alchemy/devboards/db1000.c
+++ b/arch/mips/alchemy/devboards/db1000.c
@@ -25,6 +25,7 @@
#include <linux/interrupt.h>
#include <linux/leds.h>
#include <linux/mmc/host.h>
+#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
#include <linux/spi/spi.h>
--
1.7.7.2
^ permalink raw reply related [flat|nested] 46+ messages in thread
* Re: [PATCH] MIPS: Alchemy: db1300: fix build: missing module.h
2011-11-09 18:38 ` [PATCH] MIPS: Alchemy: db1300: fix build: missing module.h Manuel Lauss
@ 2011-11-09 18:48 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 18:48 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
On Wed, Nov 09, 2011 at 07:38:46PM +0100, Manuel Lauss wrote:
> add module.h to fix build (symbol_get/symbol_put) against 3.2-rc1
>
> Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
> ---
> Please fold into "[PATCH 05/18] Basic support for the DB1300 board."
Done.
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH] MIPS: Alchemy: db1100: fix build: missing module.h
2011-11-09 18:39 ` [PATCH] MIPS: Alchemy: db1100: fix build: missing module.h Manuel Lauss
@ 2011-11-09 18:55 ` Ralf Baechle
0 siblings, 0 replies; 46+ messages in thread
From: Ralf Baechle @ 2011-11-09 18:55 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
On Wed, Nov 09, 2011 at 07:39:15PM +0100, Manuel Lauss wrote:
> fix build against 3.2-rc1, add a missing module.h (symbol_get/symbol_put).
>
> Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
> ---
> Please fold into "[PATCH 12/18] MIPS: Alchemy: MMC for DB1100".
Done, but:
patching file arch/mips/alchemy/devboards/db1000.c
Hunk #1 succeeded at 25 with fuzz 1.
As with every use of symbol_get I wonder if this is not a case of doing
something the very wrong way.
Ralf
^ permalink raw reply [flat|nested] 46+ messages in thread
end of thread, other threads:[~2011-11-09 18:56 UTC | newest]
Thread overview: 46+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-11-01 19:03 [PATCH 00/18] MIPS: Alchemy board and driver updates Manuel Lauss
2011-11-01 19:03 ` [PATCH 01/18] MIPS: Alchemy: remove PB1000 support Manuel Lauss
2011-11-02 11:37 ` Ralf Baechle
2011-11-02 11:53 ` [PATCH RESEND " Manuel Lauss
2011-11-09 14:48 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 02/18] MIPS: Alchemy: drop MIRAGE/BOSPORUS board support Manuel Lauss
2011-11-09 14:49 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 03/18] MIPS: Alchemy: devboards: remove unneeded BCSR IRQ reg acc Manuel Lauss
2011-11-09 14:49 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 04/18] MIPS: Alchemy: Au1300 SoC support Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 05/18] MIPS: Alchemy: DB1300 support Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-09 18:38 ` [PATCH] MIPS: Alchemy: db1300: fix build: missing module.h Manuel Lauss
2011-11-09 18:48 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 06/18] MIPS: Alchemy: better DB1550 support Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 07/18] MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 08/18] MIPS: Alchemy: merge devboard code into single per-board files Manuel Lauss
2011-11-04 8:35 ` [PATCH v2 " Manuel Lauss
2011-11-09 14:50 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 09/18] MIPS: Alchemy: move au1200fb global functions to platform data Manuel Lauss
2011-11-01 19:03 ` Manuel Lauss
2011-11-09 14:52 ` Ralf Baechle
2011-11-09 14:52 ` [PATCH 09/18] MIPS: Alchemy: move au1200fb global functions to Ralf Baechle
2011-11-01 19:03 ` [PATCH 10/18] MIPS: Alchemy: Merge PB1200 support into DB1200 code Manuel Lauss
2011-11-09 14:52 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 11/18] MIPS: Alchemy: one kernel for DB1000/DB1500/DB1100 Manuel Lauss
2011-11-09 14:53 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 12/18] MIPS: Alchemy: MMC for DB1100 Manuel Lauss
2011-11-09 14:53 ` Ralf Baechle
2011-11-09 18:39 ` [PATCH] MIPS: Alchemy: db1100: fix build: missing module.h Manuel Lauss
2011-11-09 18:55 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 13/18] MIPS: Alchemy: add RTC device to all devboards Manuel Lauss
2011-11-09 14:53 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 14/18] MTD: nand: make au1550nd.c a platform_driver Manuel Lauss
2011-11-09 14:54 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 15/18] MIPS: Alchemy: remove unused board headers Manuel Lauss
2011-11-09 14:55 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 16/18] net/irda: convert au1k_ir to platform driver Manuel Lauss
2011-11-09 14:55 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 17/18] MIPS: Alchemy: hook up IrDA on DB1000/DB1100 Manuel Lauss
2011-11-09 14:56 ` Ralf Baechle
2011-11-01 19:03 ` [PATCH 18/18] MIPS: Alchemy: Touchscreen support on DB1100 Manuel Lauss
2011-11-09 14:56 ` Ralf Baechle
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.