[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Fabio Estevam]

Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   35 ++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    2 +
 board/denx/m28evk/m28evk.c                 |   35 ----------------------------
 3 files changed, 37 insertions(+), 35 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..785978f 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,41 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		puts("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[0] = 0x00;
+	mac[1] = 0x04;
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+}
+#else
+void imx_get_mac_from_fuse(char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index be1f7db..cf5ab16 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 			const unsigned int iomux_size);
 #endif
 
+void imx_get_mac_from_fuse(char *mac);
+
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index fcee046..005446a 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
-- 
1.7.1

[U-Boot] [PATCH v2 2/3] mx28: Let dram_init be common for mx28

[Fabio Estevam]

Let dram_init function be a common function, so that other mx28 boards 
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   21 +++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    1 +
 board/denx/m28evk/m28evk.c                 |   21 ---------------------
 3 files changed, 22 insertions(+), 21 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 785978f..ec8eaf9 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -249,6 +249,27 @@ void imx_get_mac_from_fuse(char *mac)
 }
 #endif
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+int dram_init(void)
+{
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		puts("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size!\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
+	return 0;
+}
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index cf5ab16..745b84d 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -36,5 +36,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 #endif
 
 void imx_get_mac_from_fuse(char *mac);
+int dram_init(void);
 
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 005446a..d6a2a50 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -70,27 +70,6 @@ int board_init(void)
 	return 0;
 }
 
-#define	HW_DIGCTRL_SCRATCH0	0x8001c280
-#define	HW_DIGCTRL_SCRATCH1	0x8001c290
-int dram_init(void)
-{
-	uint32_t sz[2];
-
-	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
-	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
-
-	if (sz[0] != sz[1]) {
-		printf("MX28:\n"
-			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
-			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
-			"verify these two registers contain valid RAM size!\n");
-		hang();
-	}
-
-	gd->ram_size = sz[0];
-	return 0;
-}
-
 #ifdef	CONFIG_CMD_MMC
 static int m28_mmc_wp(int id)
 {
-- 
1.7.1

[U-Boot] [PATCH v2 2/3] mx28: Let dram_init be common for mx28

[Marek Vasut]

> Let dram_init function be a common function, so that other mx28 boards
> can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
>  arch/arm/cpu/arm926ejs/mx28/mx28.c         |   21 +++++++++++++++++++++
>  arch/arm/include/asm/arch-mx28/sys_proto.h |    1 +
>  board/denx/m28evk/m28evk.c                 |   21 ---------------------
>  3 files changed, 22 insertions(+), 21 deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> b/arch/arm/cpu/arm926ejs/mx28/mx28.c index 785978f..ec8eaf9 100644
> --- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> +++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> @@ -249,6 +249,27 @@ void imx_get_mac_from_fuse(char *mac)
>  }
>  #endif
> 
> +#define	HW_DIGCTRL_SCRATCH0	0x8001c280
> +#define	HW_DIGCTRL_SCRATCH1	0x8001c290
> +int dram_init(void)
> +{
> +	uint32_t sz[2];
> +
> +	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
> +	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
> +
> +	if (sz[0] != sz[1]) {
> +		puts("MX28:\n"
> +			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
> +			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
> +			"verify these two registers contain valid RAM size!\n");
> +		hang();
> +	}
> +
> +	gd->ram_size = sz[0];
> +	return 0;
> +}
> +
>  U_BOOT_CMD(
>  	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
>  	"display clocks",
> diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h
> b/arch/arm/include/asm/arch-mx28/sys_proto.h index cf5ab16..745b84d 100644
> --- a/arch/arm/include/asm/arch-mx28/sys_proto.h
> +++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
> @@ -36,5 +36,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
>  #endif
> 
>  void imx_get_mac_from_fuse(char *mac);
> +int dram_init(void);

Rename it to mx28_dram_init() or something please.

> 
>  #endif	/* __MX28_H__ */
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> index 005446a..d6a2a50 100644
> --- a/board/denx/m28evk/m28evk.c
> +++ b/board/denx/m28evk/m28evk.c
> @@ -70,27 +70,6 @@ int board_init(void)
>  	return 0;
>  }
> 
> -#define	HW_DIGCTRL_SCRATCH0	0x8001c280
> -#define	HW_DIGCTRL_SCRATCH1	0x8001c290
> -int dram_init(void)
> -{
> -	uint32_t sz[2];
> -
> -	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
> -	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
> -
> -	if (sz[0] != sz[1]) {
> -		printf("MX28:\n"
> -			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
> -			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
> -			"verify these two registers contain valid RAM size!\n");
> -		hang();
> -	}
> -
> -	gd->ram_size = sz[0];
> -	return 0;
> -}
> -
>  #ifdef	CONFIG_CMD_MMC
>  static int m28_mmc_wp(int id)
>  {

M

[U-Boot] [PATCH v2 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
- For correct operation of saving environment variables into the SD card,
the following patch is needed:
http://lists.denx.de/pipermail/u-boot/2011-November/111448.html

Changes since v1:
- Read the MAC from fuses
- Use tabs instead of space in u-boot.bd
- Use puts instead of print
- Factor out mac reading function
- Factor out ddr size calculation function
- Use GENERATED_GBL_DATA_SIZE
- Protect CONFIG_ENV_IS_IN_MMC

 MAINTAINERS                                |    1 +
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   56 +++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    3 +
 board/denx/m28evk/m28evk.c                 |   56 ---------
 board/freescale/common/sdhc_boot.c         |    2 +
 board/freescale/mx28evk/Makefile           |   49 ++++++++
 board/freescale/mx28evk/iomux.c            |  138 ++++++++++++++++++++++
 board/freescale/mx28evk/mx28evk.c          |  164 ++++++++++++++++++++++++++
 board/freescale/mx28evk/u-boot.bd          |   14 +++
 boards.cfg                                 |    1 +
 include/configs/mx28evk.h                  |  172 ++++++++++++++++++++++++++++
 11 files changed, 600 insertions(+), 56 deletions(-)
 create mode 100644 board/freescale/mx28evk/Makefile
 create mode 100644 board/freescale/mx28evk/iomux.c
 create mode 100644 board/freescale/mx28evk/mx28evk.c
 create mode 100644 board/freescale/mx28evk/u-boot.bd
 create mode 100644 include/configs/mx28evk.h

diff --git a/MAINTAINERS b/MAINTAINERS
index a56ca10..72e1089 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
 Fabio Estevam <fabio.estevam@freescale.com>
 
 	mx25pdk		i.MX25
+	mx28evk		i.MX28
 	mx31pdk		i.MX31
 	mx53ard		i.MX53
 	mx53smd		i.MX53
diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..e15b158 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,62 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		puts("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[0] = 0x00;
+	mac[1] = 0x04;
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+}
+#else
+void imx_get_mac_from_fuse(char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+int dram_init(void)
+{
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		puts("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size!\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
+	return 0;
+}
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index be1f7db..745b84d 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -35,4 +35,7 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 			const unsigned int iomux_size);
 #endif
 
+void imx_get_mac_from_fuse(char *mac);
+int dram_init(void);
+
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index fcee046..d6a2a50 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -70,27 +70,6 @@ int board_init(void)
 	return 0;
 }
 
-#define	HW_DIGCTRL_SCRATCH0	0x8001c280
-#define	HW_DIGCTRL_SCRATCH1	0x8001c290
-int dram_init(void)
-{
-	uint32_t sz[2];
-
-	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
-	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
-
-	if (sz[0] != sz[1]) {
-		printf("MX28:\n"
-			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
-			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
-			"verify these two registers contain valid RAM size!\n");
-		hang();
-	}
-
-	gd->ram_size = sz[0];
-	return 0;
-}
-
 #ifdef	CONFIG_CMD_MMC
 static int m28_mmc_wp(int id)
 {
@@ -178,39 +157,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
diff --git a/board/freescale/common/sdhc_boot.c b/board/freescale/common/sdhc_boot.c
index e432318..40b40df 100644
--- a/board/freescale/common/sdhc_boot.c
+++ b/board/freescale/common/sdhc_boot.c
@@ -32,6 +32,7 @@
 #define ESDHC_BOOT_IMAGE_SIZE	0x48
 #define ESDHC_BOOT_IMAGE_ADDR	0x50
 
+#if 0
 int mmc_get_env_addr(struct mmc *mmc, u32 *env_addr)
 {
 	u8 *tmp_buf;
@@ -61,3 +62,4 @@ int mmc_get_env_addr(struct mmc *mmc, u32 *env_addr)
 
 	return 0;
 }
+#endif
diff --git a/board/freescale/mx28evk/Makefile b/board/freescale/mx28evk/Makefile
new file mode 100644
index 0000000..7459107
--- /dev/null
+++ b/board/freescale/mx28evk/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifndef	CONFIG_SPL_BUILD
+COBJS	:= mx28evk.o
+else
+COBJS	:= iomux.o
+endif
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+all:	$(ALL)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
new file mode 100644
index 0000000..904e3f3
--- /dev/null
+++ b/board/freescale/mx28evk/iomux.c
@@ -0,0 +1,138 @@
+/*
+ * Freescale MX28EVK IOMUX setup
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+	/* DUART */
+	MX28_PAD_PWM0__DUART_RX,
+	MX28_PAD_PWM1__DUART_TX,
+
+	/* MMC0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	/* write protect */
+	MX28_PAD_SSP1_SCK__GPIO_2_12,
+	/* MMC0 slot power enable */
+	MX28_PAD_PWM3__GPIO_3_28 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+	/* FEC0 Enable */
+	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+		(MXS_PAD_12MA | MXS_PAD_3V3),
+	/* FEC0 Reset */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC1 */
+	MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+
+	/* EMI */
+	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+};
+
+void board_init_ll(void)
+{
+	mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c
new file mode 100644
index 0000000..748180b
--- /dev/null
+++ b/board/freescale/mx28evk/mx28evk.c
@@ -0,0 +1,164 @@
+/*
+ * Freescale MX28EVK board
+ *
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.c:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+	/* IO0 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP0 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
+	/* SSP2 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_MMC
+static int mx28evk_mmc_wp(int id)
+{
+	if (id != 0) {
+		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
+		return 1;
+	}
+
+	return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	/* Configure WP as input */
+	gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
+
+	/* Configure MMC0 Power Enable */
+	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
+
+	return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
+}
+#endif
+
+#ifdef	CONFIG_CMD_NET
+
+#define	MII_OPMODE_STRAP_OVERRIDE	0x16
+#define	MII_PHY_CTRL1			0x1e
+#define	MII_PHY_CTRL2			0x1f
+
+int fecmxc_mii_postcall(int phy)
+{
+	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
+	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
+	if (phy == 3)
+		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct mx28_clkctrl_regs *clkctrl_regs =
+		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+	struct eth_device *dev;
+	int ret;
+
+	ret = cpu_eth_init(bis);
+
+	/* MX28EVK uses ENET_CLK PAD to drive FEC clock */
+	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+					&clkctrl_regs->hw_clkctrl_enet);
+
+	/* Power-on FECs */
+	gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
+
+	/* Reset FEC PHYs */
+	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+	udelay(200);
+	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC0\n");
+		return ret;
+	}
+
+	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC1\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC0");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC0 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC0 mii postcall\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC1");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC1 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC1 mii postcall\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+#endif
diff --git a/board/freescale/mx28evk/u-boot.bd b/board/freescale/mx28evk/u-boot.bd
new file mode 100644
index 0000000..c60615a
--- /dev/null
+++ b/board/freescale/mx28evk/u-boot.bd
@@ -0,0 +1,14 @@
+sources {
+	u_boot_spl="spl/u-boot-spl.bin";
+	u_boot="u-boot.bin";
+}
+
+section (0) {
+	load u_boot_spl > 0x0000;
+	load ivt (entry = 0x0014) > 0x8000;
+	hab call 0x8000;
+
+	load u_boot > 0x40000100;
+	load ivt (entry = 0x40000100) > 0x8000;
+	hab call 0x8000;
+}
diff --git a/boards.cfg b/boards.cfg
index 1e5b3e0..e859024 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -160,6 +160,7 @@ zmx25                        arm         arm926ejs   zmx25               syteco
 imx27lite                    arm         arm926ejs   imx27lite           logicpd        mx27
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 m28evk                       arm         arm926ejs   -                   denx           mx28
+mx28evk                      arm         arm926ejs   -                   freescale      mx28
 nhk8815                      arm         arm926ejs   nhk8815             st             nomadik
 nhk8815_onenand              arm         arm926ejs   nhk8815             st             nomadik       nhk8815:BOOT_ONENAND
 omap1610h2		     arm	 arm926ejs   omap1610inn	 ti		omap	    omap1610inn:CS3_BOOT
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
new file mode 100644
index 0000000..40b64bf
--- /dev/null
+++ b/include/configs/mx28evk.h
@@ -0,0 +1,172 @@
+/*
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/regs-base.h>
+
+/*
+ * SoC configurations
+ */
+#define	CONFIG_MX28				/* i.MX28 SoC */
+#define	CONFIG_MXS_GPIO				/* GPIO control */
+#define	CONFIG_SYS_HZ		1000		/* Ticks per second */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
+
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ICACHE_OFF
+#define	CONFIG_SYS_DCACHE_OFF
+#define	CONFIG_BOARD_EARLY_INIT_F
+#define	CONFIG_ARCH_CPU_INIT
+#define	CONFIG_ARCH_MISC_INIT
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+#define	CONFIG_DISPLAY_CPUINFO
+#define	CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define	CONFIG_CMD_CACHE
+#define	CONFIG_CMD_DHCP
+#define	CONFIG_CMD_GPIO
+#define	CONFIG_CMD_MII
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_NET
+#define	CONFIG_CMD_NFS
+#define	CONFIG_CMD_PING
+
+/*
+ * Memory configurations
+ */
+#define	CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
+#define	PHYS_SDRAM_1			0x40000000	/* Base address */
+#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
+#define	CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack */
+#define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
+#define	CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start adr */
+#define	CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test */
+#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+/* Point initial SP in SRAM so SPL can use it too. */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
+#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*
+ * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
+ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
+ * binary. In case there was more of this mess, 0x100 bytes are skipped.
+ */
+#define	CONFIG_SYS_TEXT_BASE		0x40000100
+
+#define CONFIG_ENV_OVERWRITE
+/*
+ * U-Boot general configurations
+ */
+#define	CONFIG_SYS_LONGHELP
+#define	CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
+#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
+#define	CONFIG_SYS_PBSIZE	\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print buffer size */
+#define	CONFIG_SYS_MAXARGS	32		/* Max number of command args */
+#define	CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+						/* Boot argument buffer size */
+#define	CONFIG_VERSION_VARIABLE			/* U-BOOT version */
+#define	CONFIG_AUTO_COMPLETE			/* Command auto complete */
+#define	CONFIG_CMDLINE_EDITING			/* Command history etc */
+#define	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Serial Driver
+ */
+#define	CONFIG_PL011_SERIAL
+#define	CONFIG_PL011_CLOCK		24000000
+#define	CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
+#define	CONFIG_CONS_INDEX		0
+#define	CONFIG_BAUDRATE			115200	/* Default baud rate */
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * MMC Driver
+ */
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET	(256 * 1024)
+#define CONFIG_ENV_SIZE		(16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_CMD_SAVEENV
+#define	CONFIG_GENERIC_MMC
+#define	CONFIG_MXS_MMC
+#endif
+
+/*
+ * Ethernet on SOC (FEC)
+ */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_NET_MULTI
+#define	CONFIG_ETHPRIME			"FEC0"
+#define	CONFIG_FEC_MXC
+#define	CONFIG_FEC_MXC_MULTI
+#define	CONFIG_MII
+#define	CONFIG_DISCOVER_PHY
+#define	CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/*
+ * Boot Linux
+ */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+#define	CONFIG_BOOTDELAY	3
+#define	CONFIG_BOOTFILE		"uImage"
+#define	CONFIG_BOOTCOMMAND	"run bootcmd_net"
+#define	CONFIG_LOADADDR		0x42000000
+#define	CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console_fsl=console=ttyAM0" \
+	"console_mainline=console=ttyAMA0" \
+	"netargs=setenv bootargs console=${console_mainline}" \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
+	"bootcmd_net=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#endif /* __CONFIG_H */
-- 
1.7.1

[U-Boot] [PATCH v2 3/3] mx28evk: Add initial support for MX28EVK board

[Stefano Babic]

On 15/12/2011 17:21, Fabio Estevam wrote:
> Add initial support for Freescale MX28EVK board.
> 
> Tested boot via SD card and by loading a kernel via TFTP through
> the FEC interface.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
> - For correct operation of saving environment variables into the SD card,
> the following patch is needed:
> http://lists.denx.de/pipermail/u-boot/2011-November/111448.html
> 
> Changes since v1:
> - Read the MAC from fuses
> - Use tabs instead of space in u-boot.bd
> - Use puts instead of print
> - Factor out mac reading function
> - Factor out ddr size calculation function
> - Use GENERATED_GBL_DATA_SIZE
> - Protect CONFIG_ENV_IS_IN_MMC
> 
>  MAINTAINERS                                |    1 +
>  arch/arm/cpu/arm926ejs/mx28/mx28.c         |   56 +++++++++
>  arch/arm/include/asm/arch-mx28/sys_proto.h |    3 +
>  board/denx/m28evk/m28evk.c                 |   56 ---------
>  board/freescale/common/sdhc_boot.c         |    2 +
>  board/freescale/mx28evk/Makefile           |   49 ++++++++
>  board/freescale/mx28evk/iomux.c            |  138 ++++++++++++++++++++++
>  board/freescale/mx28evk/mx28evk.c          |  164 ++++++++++++++++++++++++++
>  board/freescale/mx28evk/u-boot.bd          |   14 +++
>  boards.cfg                                 |    1 +
>  include/configs/mx28evk.h                  |  172 ++++++++++++++++++++++++++++
>  11 files changed, 600 insertions(+), 56 deletions(-)
>  create mode 100644 board/freescale/mx28evk/Makefile
>  create mode 100644 board/freescale/mx28evk/iomux.c
>  create mode 100644 board/freescale/mx28evk/mx28evk.c
>  create mode 100644 board/freescale/mx28evk/u-boot.bd
>  create mode 100644 include/configs/mx28evk.h
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index a56ca10..72e1089 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
>  Fabio Estevam <fabio.estevam@freescale.com>
>  
>  	mx25pdk		i.MX25
> +	mx28evk		i.MX28
>  	mx31pdk		i.MX31
>  	mx53ard		i.MX53
>  	mx53smd		i.MX53
> diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> index 088c019..e15b158 100644
> --- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> +++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> @@ -214,6 +214,62 @@ int cpu_eth_init(bd_t *bis)
>  }
>  #endif
>  
> +#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
> +
> +#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> +void imx_get_mac_from_fuse(char *mac)
> +{
> +	struct mx28_ocotp_regs *ocotp_regs =
> +		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> +	uint32_t data;

Wait...this patch conflict with your first patch of your patchset, where
you have already move this code in a common place. Anything wrong with
your patchset ?

Regards,
Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v2 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

On Thu, Dec 15, 2011 at 2:42 PM, Stefano Babic <sbabic@denx.de> wrote:

> Wait...this patch conflict with your first patch of your patchset, where
> you have already move this code in a common place. Anything wrong with
> your patchset ?

Sorry about that. I sent a fixed v3 version.

Thanks,

Fabio Estevam

[U-Boot] [PATCH v3 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Fabio Estevam]

Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   35 ++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    2 +
 board/denx/m28evk/m28evk.c                 |   35 ----------------------------
 3 files changed, 37 insertions(+), 35 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..785978f 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,41 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		puts("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[0] = 0x00;
+	mac[1] = 0x04;
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+}
+#else
+void imx_get_mac_from_fuse(char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index be1f7db..cf5ab16 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 			const unsigned int iomux_size);
 #endif
 
+void imx_get_mac_from_fuse(char *mac);
+
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index fcee046..005446a 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
-- 
1.7.1

[U-Boot] [PATCH v3 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 


Please add summaries (what does "v2" "v3" etc. change ...) so we don't have to 
review this again and again.

M

[U-Boot] [PATCH v3 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Stefano Babic]

On 15/12/2011 17:34, Fabio Estevam wrote:
> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

Hi Fabio,

> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> +				MXS_OCOTP_MAX_TIMEOUT)) {
> +		puts("MXS FEC: Can't get MAC from OCOTP\n");
> +		return;
> +	}
> +
> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> +
> +	mac[0] = 0x00;
> +	mac[1] = 0x04;

Maybe it is worth to add a comment to explain that the magic numbers
0x00 - 0x04 are the Freescale's vendor prefix.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v3 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Wolfgang Denk]

Dear Fabio,

In message <4EEA340A.3080802@denx.de> Stefano Babic wrote:
> On 15/12/2011 17:34, Fabio Estevam wrote:
> > Let imx_get_mac_from_fuse function be a common function, so that other
> > mx28 boards can reuse it.
> > 
> > Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> > ---
> 
> Hi Fabio,
> 
> > +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> > +				MXS_OCOTP_MAX_TIMEOUT)) {
> > +		puts("MXS FEC: Can't get MAC from OCOTP\n");
> > +		return;
> > +	}
> > +
> > +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> > +
> > +	mac[0] = 0x00;
> > +	mac[1] = 0x04;
> 
> Maybe it is worth to add a comment to explain that the magic numbers
> 0x00 - 0x04 are the Freescale's vendor prefix.

This is a common file, right?  Then what about boards from other
vendors?

I think this is not OK as is.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Dealing with failure is easy: work hard to improve. Success  is  also
easy  to  handle:  you've  solved  the  wrong  problem.  Work hard to
improve.

[U-Boot] [PATCH v3 2/3] mx28: Let dram_init be common for mx28

[Fabio Estevam]

Let dram_init function be a common function, so that other mx28 boards 
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   21 +++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    1 +
 board/denx/m28evk/m28evk.c                 |   21 ---------------------
 3 files changed, 22 insertions(+), 21 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 785978f..ec8eaf9 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -249,6 +249,27 @@ void imx_get_mac_from_fuse(char *mac)
 }
 #endif
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+int dram_init(void)
+{
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		puts("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size!\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
+	return 0;
+}
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index cf5ab16..745b84d 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -36,5 +36,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 #endif
 
 void imx_get_mac_from_fuse(char *mac);
+int dram_init(void);
 
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 005446a..d6a2a50 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -70,27 +70,6 @@ int board_init(void)
 	return 0;
 }
 
-#define	HW_DIGCTRL_SCRATCH0	0x8001c280
-#define	HW_DIGCTRL_SCRATCH1	0x8001c290
-int dram_init(void)
-{
-	uint32_t sz[2];
-
-	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
-	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
-
-	if (sz[0] != sz[1]) {
-		printf("MX28:\n"
-			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
-			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
-			"verify these two registers contain valid RAM size!\n");
-		hang();
-	}
-
-	gd->ram_size = sz[0];
-	return 0;
-}
-
 #ifdef	CONFIG_CMD_MMC
 static int m28_mmc_wp(int id)
 {
-- 
1.7.1

[U-Boot] [PATCH v3 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
- For correct operation of saving environment variables into the SD card,
the following patch is needed:
http://lists.denx.de/pipermail/u-boot/2011-November/111448.html

Changes since v2:
- Generate the patch again due to error in applying unrelated changes
Changes since v1:
- Read the MAC from fuses
- Use tabs instead of space in u-boot.bd
- Use puts instead of print
- Factor out mac reading function
- Factor out ddr size calculation function
- Use GENERATED_GBL_DATA_SIZE
- Protect CONFIG_ENV_IS_IN_MMC
 MAINTAINERS                       |    1 +
 board/freescale/mx28evk/Makefile  |   49 +++++++++++
 board/freescale/mx28evk/iomux.c   |  138 +++++++++++++++++++++++++++++
 board/freescale/mx28evk/mx28evk.c |  164 +++++++++++++++++++++++++++++++++++
 board/freescale/mx28evk/u-boot.bd |   14 +++
 boards.cfg                        |    1 +
 include/configs/mx28evk.h         |  172 +++++++++++++++++++++++++++++++++++++
 7 files changed, 539 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx28evk/Makefile
 create mode 100644 board/freescale/mx28evk/iomux.c
 create mode 100644 board/freescale/mx28evk/mx28evk.c
 create mode 100644 board/freescale/mx28evk/u-boot.bd
 create mode 100644 include/configs/mx28evk.h

diff --git a/MAINTAINERS b/MAINTAINERS
index a56ca10..72e1089 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
 Fabio Estevam <fabio.estevam@freescale.com>
 
 	mx25pdk		i.MX25
+	mx28evk		i.MX28
 	mx31pdk		i.MX31
 	mx53ard		i.MX53
 	mx53smd		i.MX53
diff --git a/board/freescale/mx28evk/Makefile b/board/freescale/mx28evk/Makefile
new file mode 100644
index 0000000..7459107
--- /dev/null
+++ b/board/freescale/mx28evk/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifndef	CONFIG_SPL_BUILD
+COBJS	:= mx28evk.o
+else
+COBJS	:= iomux.o
+endif
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+all:	$(ALL)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
new file mode 100644
index 0000000..904e3f3
--- /dev/null
+++ b/board/freescale/mx28evk/iomux.c
@@ -0,0 +1,138 @@
+/*
+ * Freescale MX28EVK IOMUX setup
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+	/* DUART */
+	MX28_PAD_PWM0__DUART_RX,
+	MX28_PAD_PWM1__DUART_TX,
+
+	/* MMC0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	/* write protect */
+	MX28_PAD_SSP1_SCK__GPIO_2_12,
+	/* MMC0 slot power enable */
+	MX28_PAD_PWM3__GPIO_3_28 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+	/* FEC0 Enable */
+	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+		(MXS_PAD_12MA | MXS_PAD_3V3),
+	/* FEC0 Reset */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC1 */
+	MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+
+	/* EMI */
+	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+};
+
+void board_init_ll(void)
+{
+	mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c
new file mode 100644
index 0000000..748180b
--- /dev/null
+++ b/board/freescale/mx28evk/mx28evk.c
@@ -0,0 +1,164 @@
+/*
+ * Freescale MX28EVK board
+ *
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.c:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+	/* IO0 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP0 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
+	/* SSP2 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_MMC
+static int mx28evk_mmc_wp(int id)
+{
+	if (id != 0) {
+		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
+		return 1;
+	}
+
+	return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	/* Configure WP as input */
+	gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
+
+	/* Configure MMC0 Power Enable */
+	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
+
+	return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
+}
+#endif
+
+#ifdef	CONFIG_CMD_NET
+
+#define	MII_OPMODE_STRAP_OVERRIDE	0x16
+#define	MII_PHY_CTRL1			0x1e
+#define	MII_PHY_CTRL2			0x1f
+
+int fecmxc_mii_postcall(int phy)
+{
+	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
+	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
+	if (phy == 3)
+		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct mx28_clkctrl_regs *clkctrl_regs =
+		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+	struct eth_device *dev;
+	int ret;
+
+	ret = cpu_eth_init(bis);
+
+	/* MX28EVK uses ENET_CLK PAD to drive FEC clock */
+	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+					&clkctrl_regs->hw_clkctrl_enet);
+
+	/* Power-on FECs */
+	gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
+
+	/* Reset FEC PHYs */
+	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+	udelay(200);
+	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC0\n");
+		return ret;
+	}
+
+	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC1\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC0");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC0 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC0 mii postcall\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC1");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC1 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC1 mii postcall\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+#endif
diff --git a/board/freescale/mx28evk/u-boot.bd b/board/freescale/mx28evk/u-boot.bd
new file mode 100644
index 0000000..c60615a
--- /dev/null
+++ b/board/freescale/mx28evk/u-boot.bd
@@ -0,0 +1,14 @@
+sources {
+	u_boot_spl="spl/u-boot-spl.bin";
+	u_boot="u-boot.bin";
+}
+
+section (0) {
+	load u_boot_spl > 0x0000;
+	load ivt (entry = 0x0014) > 0x8000;
+	hab call 0x8000;
+
+	load u_boot > 0x40000100;
+	load ivt (entry = 0x40000100) > 0x8000;
+	hab call 0x8000;
+}
diff --git a/boards.cfg b/boards.cfg
index 1e5b3e0..e859024 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -160,6 +160,7 @@ zmx25                        arm         arm926ejs   zmx25               syteco
 imx27lite                    arm         arm926ejs   imx27lite           logicpd        mx27
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 m28evk                       arm         arm926ejs   -                   denx           mx28
+mx28evk                      arm         arm926ejs   -                   freescale      mx28
 nhk8815                      arm         arm926ejs   nhk8815             st             nomadik
 nhk8815_onenand              arm         arm926ejs   nhk8815             st             nomadik       nhk8815:BOOT_ONENAND
 omap1610h2		     arm	 arm926ejs   omap1610inn	 ti		omap	    omap1610inn:CS3_BOOT
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
new file mode 100644
index 0000000..40b64bf
--- /dev/null
+++ b/include/configs/mx28evk.h
@@ -0,0 +1,172 @@
+/*
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/regs-base.h>
+
+/*
+ * SoC configurations
+ */
+#define	CONFIG_MX28				/* i.MX28 SoC */
+#define	CONFIG_MXS_GPIO				/* GPIO control */
+#define	CONFIG_SYS_HZ		1000		/* Ticks per second */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
+
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ICACHE_OFF
+#define	CONFIG_SYS_DCACHE_OFF
+#define	CONFIG_BOARD_EARLY_INIT_F
+#define	CONFIG_ARCH_CPU_INIT
+#define	CONFIG_ARCH_MISC_INIT
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+#define	CONFIG_DISPLAY_CPUINFO
+#define	CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define	CONFIG_CMD_CACHE
+#define	CONFIG_CMD_DHCP
+#define	CONFIG_CMD_GPIO
+#define	CONFIG_CMD_MII
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_NET
+#define	CONFIG_CMD_NFS
+#define	CONFIG_CMD_PING
+
+/*
+ * Memory configurations
+ */
+#define	CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
+#define	PHYS_SDRAM_1			0x40000000	/* Base address */
+#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
+#define	CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack */
+#define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
+#define	CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start adr */
+#define	CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test */
+#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+/* Point initial SP in SRAM so SPL can use it too. */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
+#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*
+ * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
+ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
+ * binary. In case there was more of this mess, 0x100 bytes are skipped.
+ */
+#define	CONFIG_SYS_TEXT_BASE		0x40000100
+
+#define CONFIG_ENV_OVERWRITE
+/*
+ * U-Boot general configurations
+ */
+#define	CONFIG_SYS_LONGHELP
+#define	CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
+#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
+#define	CONFIG_SYS_PBSIZE	\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print buffer size */
+#define	CONFIG_SYS_MAXARGS	32		/* Max number of command args */
+#define	CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+						/* Boot argument buffer size */
+#define	CONFIG_VERSION_VARIABLE			/* U-BOOT version */
+#define	CONFIG_AUTO_COMPLETE			/* Command auto complete */
+#define	CONFIG_CMDLINE_EDITING			/* Command history etc */
+#define	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Serial Driver
+ */
+#define	CONFIG_PL011_SERIAL
+#define	CONFIG_PL011_CLOCK		24000000
+#define	CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
+#define	CONFIG_CONS_INDEX		0
+#define	CONFIG_BAUDRATE			115200	/* Default baud rate */
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * MMC Driver
+ */
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET	(256 * 1024)
+#define CONFIG_ENV_SIZE		(16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_CMD_SAVEENV
+#define	CONFIG_GENERIC_MMC
+#define	CONFIG_MXS_MMC
+#endif
+
+/*
+ * Ethernet on SOC (FEC)
+ */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_NET_MULTI
+#define	CONFIG_ETHPRIME			"FEC0"
+#define	CONFIG_FEC_MXC
+#define	CONFIG_FEC_MXC_MULTI
+#define	CONFIG_MII
+#define	CONFIG_DISCOVER_PHY
+#define	CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/*
+ * Boot Linux
+ */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+#define	CONFIG_BOOTDELAY	3
+#define	CONFIG_BOOTFILE		"uImage"
+#define	CONFIG_BOOTCOMMAND	"run bootcmd_net"
+#define	CONFIG_LOADADDR		0x42000000
+#define	CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console_fsl=console=ttyAM0" \
+	"console_mainline=console=ttyAMA0" \
+	"netargs=setenv bootargs console=${console_mainline}" \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
+	"bootcmd_net=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#endif /* __CONFIG_H */
-- 
1.7.1

[U-Boot] [PATCH v3 3/3] mx28evk: Add initial support for MX28EVK board

[Marek Vasut]

> Add initial support for Freescale MX28EVK board.
> 
> Tested boot via SD card and by loading a kernel via TFTP through
> the FEC interface.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

1) Do you use the DRAM init data used by DENX boards ?

> diff --git
> a/include/configs/mx28evk.h b/include/configs/mx28evk.h new file mode
> 100644
> index 0000000..40b64bf
> --- /dev/null
> +++ b/include/configs/mx28evk.h
> @@ -0,0 +1,172 @@
> +/*
> + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
> + * on behalf of DENX Software Engineering GmbH

Please recheck these ;-)
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
> + * GNU General Public License for more details.
> + */
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include <asm/arch/regs-base.h>
> +
> +/*
> + * SoC configurations
> + */
> +#define	CONFIG_MX28				/* i.MX28 SoC */
> +#define	CONFIG_MXS_GPIO				/* GPIO control */
> +#define	CONFIG_SYS_HZ		1000		/* Ticks per second */
> +
> +#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
> +
> +#define	CONFIG_SYS_NO_FLASH
> +#define	CONFIG_SYS_ICACHE_OFF
> +#define	CONFIG_SYS_DCACHE_OFF
> +#define	CONFIG_BOARD_EARLY_INIT_F
> +#define	CONFIG_ARCH_CPU_INIT
> +#define	CONFIG_ARCH_MISC_INIT
> +
> +/*
> + * SPL
> + */
> +#define CONFIG_SPL
> +#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
> +#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
> +#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +
> +/*
> + * U-Boot Commands
> + */
> +#include <config_cmd_default.h>
> +#define	CONFIG_DISPLAY_CPUINFO
> +#define	CONFIG_DOS_PARTITION
> +#define CONFIG_CMD_FAT
> +
> +#define	CONFIG_CMD_CACHE
> +#define	CONFIG_CMD_DHCP
> +#define	CONFIG_CMD_GPIO
> +#define	CONFIG_CMD_MII
> +#define	CONFIG_CMD_MMC
> +#define	CONFIG_CMD_NET
> +#define	CONFIG_CMD_NFS
> +#define	CONFIG_CMD_PING
> +
> +/*
> + * Memory configurations
> + */
> +#define	CONFIG_NR_DRAM_BANKS		1		/* 1 bank of 
DRAM */
> +#define	PHYS_SDRAM_1			0x40000000	/* Base address 
*/
> +#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM 
*/
> +#define	CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack 
*/
> +#define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for 
malloc */
> +#define	CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start 
adr */
> +#define	CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test 
*/
> +#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
> +/* Point initial SP in SRAM so SPL can use it too. */
> +
> +#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
> +#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
> +
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +/*
> + * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
> + * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
> + * binary. In case there was more of this mess, 0x100 bytes are skipped.
> + */
> +#define	CONFIG_SYS_TEXT_BASE		0x40000100
> +
> +#define CONFIG_ENV_OVERWRITE
> +/*
> + * U-Boot general configurations
> + */
> +#define	CONFIG_SYS_LONGHELP
> +#define	CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
> +#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer 
size */
> +#define	CONFIG_SYS_PBSIZE	\
> +	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
> +						/* Print buffer size */
> +#define	CONFIG_SYS_MAXARGS	32		/* Max number of command 
args */
> +#define	CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
> +						/* Boot argument buffer size */
> +#define	CONFIG_VERSION_VARIABLE			/* U-BOOT version */
> +#define	CONFIG_AUTO_COMPLETE			/* Command auto complete 
*/
> +#define	CONFIG_CMDLINE_EDITING			/* Command history etc 
*/
> +#define	CONFIG_SYS_HUSH_PARSER
> +#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
> +
> +/*
> + * Serial Driver
> + */
> +#define	CONFIG_PL011_SERIAL
> +#define	CONFIG_PL011_CLOCK		24000000
> +#define	CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
> +#define	CONFIG_CONS_INDEX		0
> +#define	CONFIG_BAUDRATE			115200	/* Default baud rate */
> +#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 
115200 }
> +
> +/*
> + * MMC Driver
> + */
> +#ifdef	CONFIG_CMD_MMC
> +#define	CONFIG_MMC
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_ENV_OFFSET	(256 * 1024)
> +#define CONFIG_ENV_SIZE		(16 * 1024)
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +#define CONFIG_CMD_SAVEENV
> +#define	CONFIG_GENERIC_MMC
> +#define	CONFIG_MXS_MMC
> +#endif
> +
> +/*
> + * Ethernet on SOC (FEC)
> + */
> +#ifdef	CONFIG_CMD_NET
> +#define	CONFIG_NET_MULTI
> +#define	CONFIG_ETHPRIME			"FEC0"
> +#define	CONFIG_FEC_MXC
> +#define	CONFIG_FEC_MXC_MULTI
> +#define	CONFIG_MII
> +#define	CONFIG_DISCOVER_PHY
> +#define	CONFIG_FEC_XCV_TYPE		RMII
> +#define CONFIG_MX28_FEC_MAC_IN_OCOTP
> +#endif
> +
> +/*
> + * Boot Linux
> + */
> +#define	CONFIG_CMDLINE_TAG
> +#define	CONFIG_SETUP_MEMORY_TAGS
> +#define	CONFIG_BOOTDELAY	3
> +#define	CONFIG_BOOTFILE		"uImage"
> +#define	CONFIG_BOOTCOMMAND	"run bootcmd_net"
> +#define	CONFIG_LOADADDR		0x42000000
> +#define	CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
> +
> +/*
> + * Extra Environments
> + */
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> +	"console_fsl=console=ttyAM0" \
> +	"console_mainline=console=ttyAMA0" \
> +	"netargs=setenv bootargs console=${console_mainline}" \
> +		"root=/dev/nfs " \
> +		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
> +	"bootcmd_net=echo Booting from net ...; " \
> +		"run netargs; " \
> +		"dhcp ${uimage}; bootm\0" \
> +
> +#endif /* __CONFIG_H */

Otherwise it seems OK.

M

[U-Boot] [PATCH v3 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

On Thu, Dec 15, 2011 at 3:25 PM, Marek Vasut <marek.vasut@gmail.com> wrote:

> 1) Do you use the DRAM init data used by DENX boards ?

Yes, same DDR settings.

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
>  arch/arm/cpu/arm926ejs/mx28/mx28.c         |   35
> ++++++++++++++++++++++++++++ arch/arm/include/asm/arch-mx28/sys_proto.h | 
>   2 +
>  board/denx/m28evk/m28evk.c                 |   35
> ---------------------------- 3 files changed, 37 insertions(+), 35
> deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> b/arch/arm/cpu/arm926ejs/mx28/mx28.c index 088c019..785978f 100644
> --- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> +++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> @@ -214,6 +214,41 @@ int cpu_eth_init(bd_t *bis)
>  }
>  #endif
> 
> +#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
> +
> +#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> +void imx_get_mac_from_fuse(char *mac)
> +{
> +	struct mx28_ocotp_regs *ocotp_regs =
> +		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> +	uint32_t data;
> +
> +	memset(mac, 0, 6);
> +
> +	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> +
> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> +				MXS_OCOTP_MAX_TIMEOUT)) {
> +		puts("MXS FEC: Can't get MAC from OCOTP\n");
> +		return;
> +	}
> +
> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> +
> +	mac[0] = 0x00;
> +	mac[1] = 0x04;

Be careful here. 0x00 0x04 prefix might not be correct for all cases!

> +	mac[2] = (data >> 24) & 0xff;
> +	mac[3] = (data >> 16) & 0xff;
> +	mac[4] = (data >> 8) & 0xff;
> +	mac[5] = data & 0xff;
> +}
> +#else
> +void imx_get_mac_from_fuse(char *mac)
> +{
> +	memset(mac, 0, 6);
> +}
> +#endif
> +
>  U_BOOT_CMD(
>  	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
>  	"display clocks",
> diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h
> b/arch/arm/include/asm/arch-mx28/sys_proto.h index be1f7db..cf5ab16 100644
> --- a/arch/arm/include/asm/arch-mx28/sys_proto.h
> +++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
> @@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
>  			const unsigned int iomux_size);
>  #endif
> 
> +void imx_get_mac_from_fuse(char *mac);
> +
>  #endif	/* __MX28_H__ */
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> index fcee046..005446a 100644
> --- a/board/denx/m28evk/m28evk.c
> +++ b/board/denx/m28evk/m28evk.c
> @@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
>  	return ret;
>  }
> 
> -#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
> -
> -#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> -void imx_get_mac_from_fuse(char *mac)
> -{
> -	struct mx28_ocotp_regs *ocotp_regs =
> -		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> -	uint32_t data;
> -
> -	memset(mac, 0, 6);
> -
> -	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> -
> -	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> -				MXS_OCOTP_MAX_TIMEOUT)) {
> -		printf("MXS FEC: Can't get MAC from OCOTP\n");
> -		return;
> -	}
> -
> -	data = readl(&ocotp_regs->hw_ocotp_cust0);
> -
> -	mac[0] = 0x00;
> -	mac[1] = 0x04;
> -	mac[2] = (data >> 24) & 0xff;
> -	mac[3] = (data >> 16) & 0xff;
> -	mac[4] = (data >> 8) & 0xff;
> -	mac[5] = data & 0xff;
> -}
> -#else
> -void imx_get_mac_from_fuse(char *mac)
> -{
> -	memset(mac, 0, 6);
> -}
> -#endif
> -
>  #endif

Otherwise, sure, it seems OK.

M

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Stefano Babic]

On 15/12/2011 18:22, Marek Vasut wrote:
>> Let imx_get_mac_from_fuse function be a common function, so that other
>> mx28 boards can reuse it.
>>
>> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Hi Marek,

>> +	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
>> +
>> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
>> +				MXS_OCOTP_MAX_TIMEOUT)) {
>> +		puts("MXS FEC: Can't get MAC from OCOTP\n");
>> +		return;
>> +	}
>> +
>> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
>> +
>> +	mac[0] = 0x00;
>> +	mac[1] = 0x04;
> 
> Be careful here. 0x00 0x04 prefix might not be correct for all cases!

But to be honest, it seems they are correct for the MX28EVK and not for
the M28EVK. The M28EVK and the M28 module are delivered with their own
MAC address that does not belong to the Freescale's range.

As far as I can see, the M28EVK starts with a Freescale's MAC, and then
the DENX MAC address (Vendor ID C0:E5:4E) is set later to the correct
value when Linux boots.

I can understand this feature in the SOC as a way to set the LSBs of the
MAC address, but leaving to the customer a way to set its own vendor id,
if he bought it.

What about to add a weak function (board_set_mac_vendor, maybe ?) that
can be called at this point to set the vendor id ? The default behavior
should be to set the Freescale's vendor id.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> On 15/12/2011 18:22, Marek Vasut wrote:
> >> Let imx_get_mac_from_fuse function be a common function, so that other
> >> mx28 boards can reuse it.
> >> 
> >> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> 
> Hi Marek,

Hi Stefano,

> 
> >> +	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> >> +
> >> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg,
> >> OCOTP_CTRL_BUSY, +				MXS_OCOTP_MAX_TIMEOUT)) {
> >> +		puts("MXS FEC: Can't get MAC from OCOTP\n");
> >> +		return;
> >> +	}
> >> +
> >> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> >> +
> >> +	mac[0] = 0x00;
> >> +	mac[1] = 0x04;
> > 
> > Be careful here. 0x00 0x04 prefix might not be correct for all cases!
> 
> But to be honest, it seems they are correct for the MX28EVK and not for
> the M28EVK. The M28EVK and the M28 module are delivered with their own
> MAC address that does not belong to the Freescale's range.
> 
> As far as I can see, the M28EVK starts with a Freescale's MAC, and then
> the DENX MAC address (Vendor ID C0:E5:4E) is set later to the correct
> value when Linux boots.

It's actually set even in uboot by ethaddr and eth1addr. This is the default 
behaviour.

> 
> I can understand this feature in the SOC as a way to set the LSBs of the
> MAC address, but leaving to the customer a way to set its own vendor id,
> if he bought it.
> 
> What about to add a weak function (board_set_mac_vendor, maybe ?) that
> can be called at this point to set the vendor id ? The default behavior
> should be to set the Freescale's vendor id.

ethaddr and eth1addr is insufficient?

M

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Stefano Babic]

On 16/12/2011 10:53, Marek Vasut wrote:
>> On 15/12/2011 18:22, Marek Vasut wrote:
>>>> Let imx_get_mac_from_fuse function be a common function, so that other
>>>> mx28 boards can reuse it.
>>>>
>>>> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
>>

Hi Marek,


>>> Be careful here. 0x00 0x04 prefix might not be correct for all cases!
>>
>> But to be honest, it seems they are correct for the MX28EVK and not for
>> the M28EVK. The M28EVK and the M28 module are delivered with their own
>> MAC address that does not belong to the Freescale's range.
>>
>> As far as I can see, the M28EVK starts with a Freescale's MAC, and then
>> the DENX MAC address (Vendor ID C0:E5:4E) is set later to the correct
>> value when Linux boots.
> 
> It's actually set even in uboot by ethaddr and eth1addr. This is the default 
> behaviour.

This means ethaddr overwrites the values read from fuses - why do we
need the fuses ?

> 
>>
>> I can understand this feature in the SOC as a way to set the LSBs of the
>> MAC address, but leaving to the customer a way to set its own vendor id,
>> if he bought it.
>>
>> What about to add a weak function (board_set_mac_vendor, maybe ?) that
>> can be called at this point to set the vendor id ? The default behavior
>> should be to set the Freescale's vendor id.
> 
> ethaddr and eth1addr is insufficient?

In a standard way, the environment must be adapted for each board to
store the MAC address in the ethaddr variable. The reason to get the MAC
directly from the hardware is that it is not required a specific initial
setup for each board, and that simplifies the production and the
delivery of the boards.

If you rely on ethaddr, than we do not need imx_get_mac_from_fuse() at
all, and the MAC can be set to zero, because in this case the ethaddr
value is used - but we lose the feature.

The reason why imx_get_mac_from_fuse was introduce is to have an
automatic mechanism to set up the MAC without any customization.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> On 16/12/2011 10:53, Marek Vasut wrote:
> >> On 15/12/2011 18:22, Marek Vasut wrote:
> >>>> Let imx_get_mac_from_fuse function be a common function, so that other
> >>>> mx28 boards can reuse it.
> >>>> 
> >>>> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> 
> Hi Marek,

Hi Stefano,

DISCLAIMER: I'm terribly tired today, had early class.

> 
> >>> Be careful here. 0x00 0x04 prefix might not be correct for all cases!
> >> 
> >> But to be honest, it seems they are correct for the MX28EVK and not for
> >> the M28EVK. The M28EVK and the M28 module are delivered with their own
> >> MAC address that does not belong to the Freescale's range.
> >> 
> >> As far as I can see, the M28EVK starts with a Freescale's MAC, and then
> >> the DENX MAC address (Vendor ID C0:E5:4E) is set later to the correct
> >> value when Linux boots.
> > 
> > It's actually set even in uboot by ethaddr and eth1addr. This is the
> > default behaviour.
> 
> This means ethaddr overwrites the values read from fuses - why do we
> need the fuses ?

You disable fuses and use ethaddr. Why do we need them? We don't, but the 
hardware is in the CPU and someone might use it so let's support it.

> 
> >> I can understand this feature in the SOC as a way to set the LSBs of the
> >> MAC address, but leaving to the customer a way to set its own vendor id,
> >> if he bought it.
> >> 
> >> What about to add a weak function (board_set_mac_vendor, maybe ?) that
> >> can be called at this point to set the vendor id ? The default behavior
> >> should be to set the Freescale's vendor id.
> > 
> > ethaddr and eth1addr is insufficient?
> 
> In a standard way, the environment must be adapted for each board to
> store the MAC address in the ethaddr variable. The reason to get the MAC
> directly from the hardware is that it is not required a specific initial
> setup for each board, and that simplifies the production and the
> delivery of the boards.

Sure, but the OCOTP capacity here is limited. But there was approach from 
Fabio/me how to make the OCOTP good enough for two NICs even.

* The idea is to let user configure the top 2 bytes per-device (which is the 
most likely case).
* Introduce mac_modify(int fec, char *mac) function, which will be called from 
imx_get_mac_from_fuse()
* The function will adjust the MAC, for example by setting top two bytes to 
preconfigured data, bottom four bytes from OCOTP and the last bit of the MAC 
from "int fec", which is 0 for FEC0 and 1 for FEC1. This should be sufficient 
for most people.
* The function will be weak so it can be overridden to your hearts content.

> 
> If you rely on ethaddr, than we do not need imx_get_mac_from_fuse() at
> all, and the MAC can be set to zero, because in this case the ethaddr
> value is used - but we lose the feature.
> 
> The reason why imx_get_mac_from_fuse was introduce is to have an
> automatic mechanism to set up the MAC without any customization.
> 
> Best regards,
> Stefano Babic

Cheers!

M

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Stefano Babic]

On 16/12/2011 11:39, Marek Vasut wrote:

>>
>> Hi Marek,
> 
> Hi Stefano,
> 
> DISCLAIMER: I'm terribly tired today, had early class.

ok, I understand..;-)

> 
> You disable fuses and use ethaddr. Why do we need them? We don't, but the 
> hardware is in the CPU and someone might use it so let's support it.

Exactly - see also othe IMX SOCs.

>> In a standard way, the environment must be adapted for each board to
>> store the MAC address in the ethaddr variable. The reason to get the MAC
>> directly from the hardware is that it is not required a specific initial
>> setup for each board, and that simplifies the production and the
>> delivery of the boards.
> 
> Sure, but the OCOTP capacity here is limited. But there was approach from 
> Fabio/me how to make the OCOTP good enough for two NICs even.

And this is nice.

> * The idea is to let user configure the top 2 bytes per-device (which is the 
> most likely case).

This is exactly what I meant.

> * Introduce mac_modify(int fec, char *mac) function, which will be called from 
> imx_get_mac_from_fuse()
> * The function will adjust the MAC, for example by setting top two bytes to 
> preconfigured data, bottom four bytes from OCOTP and the last bit of the MAC 
> from "int fec", which is 0 for FEC0 and 1 for FEC1. This should be sufficient 
> for most people.

Exactly !


> * The function will be weak so it can be overridden to your hearts content.

Right !

Stefano


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v2 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> On 16/12/2011 11:39, Marek Vasut wrote:
> >> Hi Marek,
> > 
> > Hi Stefano,
> > 
> > DISCLAIMER: I'm terribly tired today, had early class.
> 
> ok, I understand..;-)
> 
> > You disable fuses and use ethaddr. Why do we need them? We don't, but the
> > hardware is in the CPU and someone might use it so let's support it.
> 
> Exactly - see also othe IMX SOCs.
> 
> >> In a standard way, the environment must be adapted for each board to
> >> store the MAC address in the ethaddr variable. The reason to get the MAC
> >> directly from the hardware is that it is not required a specific initial
> >> setup for each board, and that simplifies the production and the
> >> delivery of the boards.
> > 
> > Sure, but the OCOTP capacity here is limited. But there was approach from
> > Fabio/me how to make the OCOTP good enough for two NICs even.
> 
> And this is nice.
> 
> > * The idea is to let user configure the top 2 bytes per-device (which is
> > the most likely case).
> 
> This is exactly what I meant.
> 
> > * Introduce mac_modify(int fec, char *mac) function, which will be called
> > from imx_get_mac_from_fuse()
> > * The function will adjust the MAC, for example by setting top two bytes
> > to preconfigured data, bottom four bytes from OCOTP and the last bit of
> > the MAC from "int fec", which is 0 for FEC0 and 1 for FEC1. This should
> > be sufficient for most people.
> 
> Exactly !
> 
> > * The function will be weak so it can be overridden to your hearts
> > content.
> 
> Right !
> 
> Stefano

And it was mostly Fabio's idea I'd say ;-)

M

[U-Boot] [PATCH v4 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Fabio Estevam]

Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Change since v3:
- Add a note about the first two MAC addresses being from Freescale vendor.

 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   41 ++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    2 +
 board/denx/m28evk/m28evk.c                 |   35 -----------------------
 3 files changed, 43 insertions(+), 35 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..d82bb01 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,47 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		puts("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[0] = 0x00;
+	mac[1] = 0x04;
+	/*
+	 * Note:
+	 *
+	 * These first two bytes are Freescale's vendor MAC prefix.
+	 *
+	 */
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+}
+#else
+void imx_get_mac_from_fuse(char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index be1f7db..cf5ab16 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 			const unsigned int iomux_size);
 #endif
 
+void imx_get_mac_from_fuse(char *mac);
+
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index fcee046..005446a 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
-- 
1.7.1

[U-Boot] [PATCH v4 2/3] mx28: Let dram_init be common for mx28

[Fabio Estevam]

Let dram_init function be a common function, so that other mx28 boards 
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v3:
- Rename dram_init to mx28_dram_init

 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   21 +++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    1 +
 board/denx/m28evk/m28evk.c                 |   21 ---------------------
 3 files changed, 22 insertions(+), 21 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index d82bb01..76b2876 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -255,6 +255,27 @@ void imx_get_mac_from_fuse(char *mac)
 }
 #endif
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+int mx28_dram_init(void)
+{
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		puts("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
+	return 0;
+}
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index cf5ab16..411173e 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -36,5 +36,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 #endif
 
 void imx_get_mac_from_fuse(char *mac);
+int mx28_dram_init(void);
 
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 005446a..d6a2a50 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -70,27 +70,6 @@ int board_init(void)
 	return 0;
 }
 
-#define	HW_DIGCTRL_SCRATCH0	0x8001c280
-#define	HW_DIGCTRL_SCRATCH1	0x8001c290
-int dram_init(void)
-{
-	uint32_t sz[2];
-
-	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
-	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
-
-	if (sz[0] != sz[1]) {
-		printf("MX28:\n"
-			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
-			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
-			"verify these two registers contain valid RAM size!\n");
-		hang();
-	}
-
-	gd->ram_size = sz[0];
-	return 0;
-}
-
 #ifdef	CONFIG_CMD_MMC
 static int m28_mmc_wp(int id)
 {
-- 
1.7.1

[U-Boot] [PATCH v4 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
- For correct operation of saving environment variables into the SD card,
the following patch is needed:
http://lists.denx.de/pipermail/u-boot/2011-November/111448.html

Changes since v3:
- Fix Copyright in mx28evk.h
- Call mx28_dram_init from dram_init
Changes since v2:
- Generate the patch again due to error in applying unrelated changes
Changes since v1:
- Read the MAC from fuses
- Use tabs instead of space in u-boot.bd
- Use puts instead of print
- Factor out mac reading function
- Factor out ddr size calculation function
- Use GENERATED_GBL_DATA_SIZE
- Protect CONFIG_ENV_IS_IN_MMC
 MAINTAINERS                       |    1 +
 board/freescale/mx28evk/Makefile  |   49 ++++++++++
 board/freescale/mx28evk/iomux.c   |  138 +++++++++++++++++++++++++++++
 board/freescale/mx28evk/mx28evk.c |  170 +++++++++++++++++++++++++++++++++++
 board/freescale/mx28evk/u-boot.bd |   14 +++
 boards.cfg                        |    1 +
 include/configs/mx28evk.h         |  176 +++++++++++++++++++++++++++++++++++++
 7 files changed, 549 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx28evk/Makefile
 create mode 100644 board/freescale/mx28evk/iomux.c
 create mode 100644 board/freescale/mx28evk/mx28evk.c
 create mode 100644 board/freescale/mx28evk/u-boot.bd
 create mode 100644 include/configs/mx28evk.h

diff --git a/MAINTAINERS b/MAINTAINERS
index a56ca10..72e1089 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
 Fabio Estevam <fabio.estevam@freescale.com>
 
 	mx25pdk		i.MX25
+	mx28evk		i.MX28
 	mx31pdk		i.MX31
 	mx53ard		i.MX53
 	mx53smd		i.MX53
diff --git a/board/freescale/mx28evk/Makefile b/board/freescale/mx28evk/Makefile
new file mode 100644
index 0000000..7459107
--- /dev/null
+++ b/board/freescale/mx28evk/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifndef	CONFIG_SPL_BUILD
+COBJS	:= mx28evk.o
+else
+COBJS	:= iomux.o
+endif
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+all:	$(ALL)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
new file mode 100644
index 0000000..904e3f3
--- /dev/null
+++ b/board/freescale/mx28evk/iomux.c
@@ -0,0 +1,138 @@
+/*
+ * Freescale MX28EVK IOMUX setup
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+	/* DUART */
+	MX28_PAD_PWM0__DUART_RX,
+	MX28_PAD_PWM1__DUART_TX,
+
+	/* MMC0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	/* write protect */
+	MX28_PAD_SSP1_SCK__GPIO_2_12,
+	/* MMC0 slot power enable */
+	MX28_PAD_PWM3__GPIO_3_28 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+	/* FEC0 Enable */
+	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+		(MXS_PAD_12MA | MXS_PAD_3V3),
+	/* FEC0 Reset */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC1 */
+	MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+
+	/* EMI */
+	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+};
+
+void board_init_ll(void)
+{
+	mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c
new file mode 100644
index 0000000..542e806
--- /dev/null
+++ b/board/freescale/mx28evk/mx28evk.c
@@ -0,0 +1,170 @@
+/*
+ * Freescale MX28EVK board
+ *
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.c:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+	/* IO0 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP0 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
+	/* SSP2 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	mx28_dram_init();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_MMC
+static int mx28evk_mmc_wp(int id)
+{
+	if (id != 0) {
+		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
+		return 1;
+	}
+
+	return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	/* Configure WP as input */
+	gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
+
+	/* Configure MMC0 Power Enable */
+	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
+
+	return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
+}
+#endif
+
+#ifdef	CONFIG_CMD_NET
+
+#define	MII_OPMODE_STRAP_OVERRIDE	0x16
+#define	MII_PHY_CTRL1			0x1e
+#define	MII_PHY_CTRL2			0x1f
+
+int fecmxc_mii_postcall(int phy)
+{
+	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
+	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
+	if (phy == 3)
+		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct mx28_clkctrl_regs *clkctrl_regs =
+		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+	struct eth_device *dev;
+	int ret;
+
+	ret = cpu_eth_init(bis);
+
+	/* MX28EVK uses ENET_CLK PAD to drive FEC clock */
+	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+					&clkctrl_regs->hw_clkctrl_enet);
+
+	/* Power-on FECs */
+	gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
+
+	/* Reset FEC PHYs */
+	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+	udelay(200);
+	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC0\n");
+		return ret;
+	}
+
+	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC1\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC0");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC0 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC0 mii postcall\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC1");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC1 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC1 mii postcall\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+#endif
diff --git a/board/freescale/mx28evk/u-boot.bd b/board/freescale/mx28evk/u-boot.bd
new file mode 100644
index 0000000..c60615a
--- /dev/null
+++ b/board/freescale/mx28evk/u-boot.bd
@@ -0,0 +1,14 @@
+sources {
+	u_boot_spl="spl/u-boot-spl.bin";
+	u_boot="u-boot.bin";
+}
+
+section (0) {
+	load u_boot_spl > 0x0000;
+	load ivt (entry = 0x0014) > 0x8000;
+	hab call 0x8000;
+
+	load u_boot > 0x40000100;
+	load ivt (entry = 0x40000100) > 0x8000;
+	hab call 0x8000;
+}
diff --git a/boards.cfg b/boards.cfg
index 1e5b3e0..e859024 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -160,6 +160,7 @@ zmx25                        arm         arm926ejs   zmx25               syteco
 imx27lite                    arm         arm926ejs   imx27lite           logicpd        mx27
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 m28evk                       arm         arm926ejs   -                   denx           mx28
+mx28evk                      arm         arm926ejs   -                   freescale      mx28
 nhk8815                      arm         arm926ejs   nhk8815             st             nomadik
 nhk8815_onenand              arm         arm926ejs   nhk8815             st             nomadik       nhk8815:BOOT_ONENAND
 omap1610h2		     arm	 arm926ejs   omap1610inn	 ti		omap	    omap1610inn:CS3_BOOT
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
new file mode 100644
index 0000000..5b8a1bf
--- /dev/null
+++ b/include/configs/mx28evk.h
@@ -0,0 +1,176 @@
+/*
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.h:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/regs-base.h>
+
+/*
+ * SoC configurations
+ */
+#define	CONFIG_MX28				/* i.MX28 SoC */
+#define	CONFIG_MXS_GPIO				/* GPIO control */
+#define	CONFIG_SYS_HZ		1000		/* Ticks per second */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
+
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ICACHE_OFF
+#define	CONFIG_SYS_DCACHE_OFF
+#define	CONFIG_BOARD_EARLY_INIT_F
+#define	CONFIG_ARCH_CPU_INIT
+#define	CONFIG_ARCH_MISC_INIT
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+#define	CONFIG_DISPLAY_CPUINFO
+#define	CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define	CONFIG_CMD_CACHE
+#define	CONFIG_CMD_DHCP
+#define	CONFIG_CMD_GPIO
+#define	CONFIG_CMD_MII
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_NET
+#define	CONFIG_CMD_NFS
+#define	CONFIG_CMD_PING
+
+/*
+ * Memory configurations
+ */
+#define	CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
+#define	PHYS_SDRAM_1			0x40000000	/* Base address */
+#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
+#define	CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack */
+#define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
+#define	CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start adr */
+#define	CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test */
+#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+/* Point initial SP in SRAM so SPL can use it too. */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
+#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*
+ * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
+ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
+ * binary. In case there was more of this mess, 0x100 bytes are skipped.
+ */
+#define	CONFIG_SYS_TEXT_BASE		0x40000100
+
+#define CONFIG_ENV_OVERWRITE
+/*
+ * U-Boot general configurations
+ */
+#define	CONFIG_SYS_LONGHELP
+#define	CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
+#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
+#define	CONFIG_SYS_PBSIZE	\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print buffer size */
+#define	CONFIG_SYS_MAXARGS	32		/* Max number of command args */
+#define	CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+						/* Boot argument buffer size */
+#define	CONFIG_VERSION_VARIABLE			/* U-BOOT version */
+#define	CONFIG_AUTO_COMPLETE			/* Command auto complete */
+#define	CONFIG_CMDLINE_EDITING			/* Command history etc */
+#define	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Serial Driver
+ */
+#define	CONFIG_PL011_SERIAL
+#define	CONFIG_PL011_CLOCK		24000000
+#define	CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
+#define	CONFIG_CONS_INDEX		0
+#define	CONFIG_BAUDRATE			115200	/* Default baud rate */
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * MMC Driver
+ */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET	(256 * 1024)
+#define CONFIG_ENV_SIZE		(16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_CMD_SAVEENV
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define	CONFIG_GENERIC_MMC
+#define	CONFIG_MXS_MMC
+#endif
+
+/*
+ * Ethernet on SOC (FEC)
+ */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_NET_MULTI
+#define	CONFIG_ETHPRIME			"FEC0"
+#define	CONFIG_FEC_MXC
+#define	CONFIG_FEC_MXC_MULTI
+#define	CONFIG_MII
+#define	CONFIG_DISCOVER_PHY
+#define	CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/*
+ * Boot Linux
+ */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+#define	CONFIG_BOOTDELAY	3
+#define	CONFIG_BOOTFILE		"uImage"
+#define	CONFIG_BOOTCOMMAND	"run bootcmd_net"
+#define	CONFIG_LOADADDR		0x42000000
+#define	CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console_fsl=console=ttyAM0" \
+	"console_mainline=console=ttyAMA0" \
+	"netargs=setenv bootargs console=${console_mainline}" \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
+	"bootcmd_net=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#endif /* __CONFIG_H */
-- 
1.7.1

[U-Boot] [PATCH v5 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Fabio Estevam]

Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v4:
- No changes
Change since v3:
- Add a note about the first two MAC addresses being from Freescale vendor.

 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   41 ++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    2 +
 board/denx/m28evk/m28evk.c                 |   35 -----------------------
 3 files changed, 43 insertions(+), 35 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..d82bb01 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,47 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		puts("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[0] = 0x00;
+	mac[1] = 0x04;
+	/*
+	 * Note:
+	 *
+	 * These first two bytes are Freescale's vendor MAC prefix.
+	 *
+	 */
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+}
+#else
+void imx_get_mac_from_fuse(char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index be1f7db..cf5ab16 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 			const unsigned int iomux_size);
 #endif
 
+void imx_get_mac_from_fuse(char *mac);
+
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index fcee046..005446a 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
-- 
1.7.1

[U-Boot] [PATCH v5 1/3] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
> Changes since v4:
> - No changes
> Change since v3:
> - Add a note about the first two MAC addresses being from Freescale vendor.

What changes are in V5? Also, mark resubmissions with "RESEND" or "V3 RESEND" or 
something ... like "[PATCH V3 RESEND]" ... though you don't need to resend stuff 
here.

> 
>  arch/arm/cpu/arm926ejs/mx28/mx28.c         |   41
> ++++++++++++++++++++++++++++ arch/arm/include/asm/arch-mx28/sys_proto.h | 
>   2 +
>  board/denx/m28evk/m28evk.c                 |   35 -----------------------
>  3 files changed, 43 insertions(+), 35 deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> b/arch/arm/cpu/arm926ejs/mx28/mx28.c index 088c019..d82bb01 100644
> --- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> +++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> @@ -214,6 +214,47 @@ int cpu_eth_init(bd_t *bis)
>  }
>  #endif
> 
> +#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
> +
> +#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> +void imx_get_mac_from_fuse(char *mac)
> +{
> +	struct mx28_ocotp_regs *ocotp_regs =
> +		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> +	uint32_t data;
> +
> +	memset(mac, 0, 6);
> +
> +	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> +
> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> +				MXS_OCOTP_MAX_TIMEOUT)) {
> +		puts("MXS FEC: Can't get MAC from OCOTP\n");
> +		return;
> +	}
> +
> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> +

/* Freescale MAC vendor prefix: 00:04:xx:xx:xx:xx */ ... or something

It's shorter and it should be above the code.

> +	mac[0] = 0x00;
> +	mac[1] = 0x04;
> +	/*
> +	 * Note:
> +	 *
> +	 * These first two bytes are Freescale's vendor MAC prefix.
> +	 *
> +	 */
> +	mac[2] = (data >> 24) & 0xff;
> +	mac[3] = (data >> 16) & 0xff;
> +	mac[4] = (data >> 8) & 0xff;
> +	mac[5] = data & 0xff;
> +}
> +#else
> +void imx_get_mac_from_fuse(char *mac)
> +{
> +	memset(mac, 0, 6);
> +}
> +#endif
> +
>  U_BOOT_CMD(
>  	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
>  	"display clocks",
> diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h
> b/arch/arm/include/asm/arch-mx28/sys_proto.h index be1f7db..cf5ab16 100644
> --- a/arch/arm/include/asm/arch-mx28/sys_proto.h
> +++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
> @@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
>  			const unsigned int iomux_size);
>  #endif
> 
> +void imx_get_mac_from_fuse(char *mac);
> +
>  #endif	/* __MX28_H__ */
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> index fcee046..005446a 100644
> --- a/board/denx/m28evk/m28evk.c
> +++ b/board/denx/m28evk/m28evk.c
> @@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
>  	return ret;
>  }
> 
> -#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
> -
> -#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> -void imx_get_mac_from_fuse(char *mac)
> -{
> -	struct mx28_ocotp_regs *ocotp_regs =
> -		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> -	uint32_t data;
> -
> -	memset(mac, 0, 6);
> -
> -	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> -
> -	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> -				MXS_OCOTP_MAX_TIMEOUT)) {
> -		printf("MXS FEC: Can't get MAC from OCOTP\n");
> -		return;
> -	}
> -
> -	data = readl(&ocotp_regs->hw_ocotp_cust0);
> -
> -	mac[0] = 0x00;
> -	mac[1] = 0x04;
> -	mac[2] = (data >> 24) & 0xff;
> -	mac[3] = (data >> 16) & 0xff;
> -	mac[4] = (data >> 8) & 0xff;
> -	mac[5] = data & 0xff;
> -}
> -#else
> -void imx_get_mac_from_fuse(char *mac)
> -{
> -	memset(mac, 0, 6);
> -}
> -#endif
> -
>  #endif

M

[U-Boot] [PATCH v5 2/3] mx28: Let dram_init be common for mx28

[Fabio Estevam]

Let dram_init function be a common function, so that other mx28 boards 
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v4:
- Call mx28_dram_init from m28evk.c
Changes since v3:
- Rename dram_init to mx28_dram_init
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   21 +++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    1 +
 board/denx/m28evk/m28evk.c                 |   25 +++++--------------------
 3 files changed, 27 insertions(+), 20 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 40ffe4c..ade3df5 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -255,6 +255,27 @@ void imx_get_mac_from_fuse(char *mac)
 }
 #endif
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+int mx28_dram_init(void)
+{
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		puts("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
+	return 0;
+}
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index cf5ab16..411173e 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -36,5 +36,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 #endif
 
 void imx_get_mac_from_fuse(char *mac);
+int mx28_dram_init(void);
 
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 005446a..3225543 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -62,32 +62,17 @@ int board_early_init_f(void)
 	return 0;
 }
 
-int board_init(void)
+int dram_init(void)
 {
-	/* Adress of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
+	mx28_dram_init();
 	return 0;
 }
 
-#define	HW_DIGCTRL_SCRATCH0	0x8001c280
-#define	HW_DIGCTRL_SCRATCH1	0x8001c290
-int dram_init(void)
+int board_init(void)
 {
-	uint32_t sz[2];
-
-	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
-	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
-
-	if (sz[0] != sz[1]) {
-		printf("MX28:\n"
-			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
-			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
-			"verify these two registers contain valid RAM size!\n");
-		hang();
-	}
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
-	gd->ram_size = sz[0];
 	return 0;
 }
 
-- 
1.7.1

[U-Boot] [PATCH v5 2/3] mx28: Let dram_init be common for mx28

[Stefano Babic]

On 15/12/2011 23:07, Fabio Estevam wrote:
> Let dram_init function be a common function, so that other mx28 boards 
> can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

> -int board_init(void)
> +int dram_init(void)
>  {
> -	/* Adress of boot parameters */
> -	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
> -
> +	mx28_dram_init();
>  	return 0;

Why not simply return mx28_dram_init() ?

We do not drop the return code if mx28_dram_init will be changed.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
- For correct operation of saving environment variables into the SD card,
the following patch is needed:
http://lists.denx.de/pipermail/u-boot/2011-November/111448.html

Changes since v4:
- No changes
Changes since v3:
- Fix Copyright in mx28evk.h
- Call mx28_dram_init from dram_init
Changes since v2:
- Generate the patch again due to error in applying unrelated changes
Changes since v1:
- Read the MAC from fuses
- Use tabs instead of space in u-boot.bd
- Use puts instead of print
- Factor out mac reading function
- Factor out ddr size calculation function
- Use GENERATED_GBL_DATA_SIZE
- Protect CONFIG_ENV_IS_IN_MMC
 MAINTAINERS                       |    1 +
 board/freescale/mx28evk/Makefile  |   49 ++++++++++
 board/freescale/mx28evk/iomux.c   |  138 +++++++++++++++++++++++++++++
 board/freescale/mx28evk/mx28evk.c |  170 +++++++++++++++++++++++++++++++++++
 board/freescale/mx28evk/u-boot.bd |   14 +++
 boards.cfg                        |    1 +
 include/configs/mx28evk.h         |  176 +++++++++++++++++++++++++++++++++++++
 7 files changed, 549 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx28evk/Makefile
 create mode 100644 board/freescale/mx28evk/iomux.c
 create mode 100644 board/freescale/mx28evk/mx28evk.c
 create mode 100644 board/freescale/mx28evk/u-boot.bd
 create mode 100644 include/configs/mx28evk.h

diff --git a/MAINTAINERS b/MAINTAINERS
index a56ca10..72e1089 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
 Fabio Estevam <fabio.estevam@freescale.com>
 
 	mx25pdk		i.MX25
+	mx28evk		i.MX28
 	mx31pdk		i.MX31
 	mx53ard		i.MX53
 	mx53smd		i.MX53
diff --git a/board/freescale/mx28evk/Makefile b/board/freescale/mx28evk/Makefile
new file mode 100644
index 0000000..7459107
--- /dev/null
+++ b/board/freescale/mx28evk/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifndef	CONFIG_SPL_BUILD
+COBJS	:= mx28evk.o
+else
+COBJS	:= iomux.o
+endif
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+all:	$(ALL)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
new file mode 100644
index 0000000..904e3f3
--- /dev/null
+++ b/board/freescale/mx28evk/iomux.c
@@ -0,0 +1,138 @@
+/*
+ * Freescale MX28EVK IOMUX setup
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+	/* DUART */
+	MX28_PAD_PWM0__DUART_RX,
+	MX28_PAD_PWM1__DUART_TX,
+
+	/* MMC0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	/* write protect */
+	MX28_PAD_SSP1_SCK__GPIO_2_12,
+	/* MMC0 slot power enable */
+	MX28_PAD_PWM3__GPIO_3_28 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+	/* FEC0 Enable */
+	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+		(MXS_PAD_12MA | MXS_PAD_3V3),
+	/* FEC0 Reset */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC1 */
+	MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+
+	/* EMI */
+	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+};
+
+void board_init_ll(void)
+{
+	mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c
new file mode 100644
index 0000000..542e806
--- /dev/null
+++ b/board/freescale/mx28evk/mx28evk.c
@@ -0,0 +1,170 @@
+/*
+ * Freescale MX28EVK board
+ *
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.c:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+	/* IO0 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP0 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
+	/* SSP2 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	mx28_dram_init();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_MMC
+static int mx28evk_mmc_wp(int id)
+{
+	if (id != 0) {
+		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
+		return 1;
+	}
+
+	return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	/* Configure WP as input */
+	gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
+
+	/* Configure MMC0 Power Enable */
+	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
+
+	return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
+}
+#endif
+
+#ifdef	CONFIG_CMD_NET
+
+#define	MII_OPMODE_STRAP_OVERRIDE	0x16
+#define	MII_PHY_CTRL1			0x1e
+#define	MII_PHY_CTRL2			0x1f
+
+int fecmxc_mii_postcall(int phy)
+{
+	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
+	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
+	if (phy == 3)
+		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct mx28_clkctrl_regs *clkctrl_regs =
+		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+	struct eth_device *dev;
+	int ret;
+
+	ret = cpu_eth_init(bis);
+
+	/* MX28EVK uses ENET_CLK PAD to drive FEC clock */
+	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+					&clkctrl_regs->hw_clkctrl_enet);
+
+	/* Power-on FECs */
+	gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
+
+	/* Reset FEC PHYs */
+	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+	udelay(200);
+	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC0\n");
+		return ret;
+	}
+
+	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC1\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC0");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC0 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC0 mii postcall\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC1");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC1 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC1 mii postcall\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+#endif
diff --git a/board/freescale/mx28evk/u-boot.bd b/board/freescale/mx28evk/u-boot.bd
new file mode 100644
index 0000000..c60615a
--- /dev/null
+++ b/board/freescale/mx28evk/u-boot.bd
@@ -0,0 +1,14 @@
+sources {
+	u_boot_spl="spl/u-boot-spl.bin";
+	u_boot="u-boot.bin";
+}
+
+section (0) {
+	load u_boot_spl > 0x0000;
+	load ivt (entry = 0x0014) > 0x8000;
+	hab call 0x8000;
+
+	load u_boot > 0x40000100;
+	load ivt (entry = 0x40000100) > 0x8000;
+	hab call 0x8000;
+}
diff --git a/boards.cfg b/boards.cfg
index 1e5b3e0..e859024 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -160,6 +160,7 @@ zmx25                        arm         arm926ejs   zmx25               syteco
 imx27lite                    arm         arm926ejs   imx27lite           logicpd        mx27
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 m28evk                       arm         arm926ejs   -                   denx           mx28
+mx28evk                      arm         arm926ejs   -                   freescale      mx28
 nhk8815                      arm         arm926ejs   nhk8815             st             nomadik
 nhk8815_onenand              arm         arm926ejs   nhk8815             st             nomadik       nhk8815:BOOT_ONENAND
 omap1610h2		     arm	 arm926ejs   omap1610inn	 ti		omap	    omap1610inn:CS3_BOOT
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
new file mode 100644
index 0000000..5b8a1bf
--- /dev/null
+++ b/include/configs/mx28evk.h
@@ -0,0 +1,176 @@
+/*
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.h:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/regs-base.h>
+
+/*
+ * SoC configurations
+ */
+#define	CONFIG_MX28				/* i.MX28 SoC */
+#define	CONFIG_MXS_GPIO				/* GPIO control */
+#define	CONFIG_SYS_HZ		1000		/* Ticks per second */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
+
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ICACHE_OFF
+#define	CONFIG_SYS_DCACHE_OFF
+#define	CONFIG_BOARD_EARLY_INIT_F
+#define	CONFIG_ARCH_CPU_INIT
+#define	CONFIG_ARCH_MISC_INIT
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+#define	CONFIG_DISPLAY_CPUINFO
+#define	CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define	CONFIG_CMD_CACHE
+#define	CONFIG_CMD_DHCP
+#define	CONFIG_CMD_GPIO
+#define	CONFIG_CMD_MII
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_NET
+#define	CONFIG_CMD_NFS
+#define	CONFIG_CMD_PING
+
+/*
+ * Memory configurations
+ */
+#define	CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
+#define	PHYS_SDRAM_1			0x40000000	/* Base address */
+#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
+#define	CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack */
+#define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
+#define	CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start adr */
+#define	CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test */
+#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+/* Point initial SP in SRAM so SPL can use it too. */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
+#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*
+ * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
+ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
+ * binary. In case there was more of this mess, 0x100 bytes are skipped.
+ */
+#define	CONFIG_SYS_TEXT_BASE		0x40000100
+
+#define CONFIG_ENV_OVERWRITE
+/*
+ * U-Boot general configurations
+ */
+#define	CONFIG_SYS_LONGHELP
+#define	CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
+#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
+#define	CONFIG_SYS_PBSIZE	\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print buffer size */
+#define	CONFIG_SYS_MAXARGS	32		/* Max number of command args */
+#define	CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+						/* Boot argument buffer size */
+#define	CONFIG_VERSION_VARIABLE			/* U-BOOT version */
+#define	CONFIG_AUTO_COMPLETE			/* Command auto complete */
+#define	CONFIG_CMDLINE_EDITING			/* Command history etc */
+#define	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Serial Driver
+ */
+#define	CONFIG_PL011_SERIAL
+#define	CONFIG_PL011_CLOCK		24000000
+#define	CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
+#define	CONFIG_CONS_INDEX		0
+#define	CONFIG_BAUDRATE			115200	/* Default baud rate */
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * MMC Driver
+ */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET	(256 * 1024)
+#define CONFIG_ENV_SIZE		(16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_CMD_SAVEENV
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define	CONFIG_GENERIC_MMC
+#define	CONFIG_MXS_MMC
+#endif
+
+/*
+ * Ethernet on SOC (FEC)
+ */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_NET_MULTI
+#define	CONFIG_ETHPRIME			"FEC0"
+#define	CONFIG_FEC_MXC
+#define	CONFIG_FEC_MXC_MULTI
+#define	CONFIG_MII
+#define	CONFIG_DISCOVER_PHY
+#define	CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/*
+ * Boot Linux
+ */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+#define	CONFIG_BOOTDELAY	3
+#define	CONFIG_BOOTFILE		"uImage"
+#define	CONFIG_BOOTCOMMAND	"run bootcmd_net"
+#define	CONFIG_LOADADDR		0x42000000
+#define	CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console_fsl=console=ttyAM0" \
+	"console_mainline=console=ttyAMA0" \
+	"netargs=setenv bootargs console=${console_mainline}" \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
+	"bootcmd_net=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#endif /* __CONFIG_H */
-- 
1.7.1

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Stefano Babic]

On 15/12/2011 23:07, Fabio Estevam wrote:
> Add initial support for Freescale MX28EVK board.
> 
> Tested boot via SD card and by loading a kernel via TFTP through
> the FEC interface.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

Hi Fabio,

> +int dram_init(void)
> +{
> +	mx28_dram_init();
> +	return 0;

return mx28_dram_init();

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Marek Vasut]

> Add initial support for Freescale MX28EVK board.
> 
> Tested boot via SD card and by loading a kernel via TFTP through
> the FEC interface.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
> - For correct operation of saving environment variables into the SD card,
> the following patch is needed:
> http://lists.denx.de/pipermail/u-boot/2011-November/111448.html
> 
> Changes since v4:
> - No changes
> Changes since v3:
> - Fix Copyright in mx28evk.h
> - Call mx28_dram_init from dram_init
> Changes since v2:
> - Generate the patch again due to error in applying unrelated changes
> Changes since v1:
> - Read the MAC from fuses
> - Use tabs instead of space in u-boot.bd
> - Use puts instead of print
> - Factor out mac reading function
> - Factor out ddr size calculation function
> - Use GENERATED_GBL_DATA_SIZE
> - Protect CONFIG_ENV_IS_IN_MMC
>  MAINTAINERS                       |    1 +
>  board/freescale/mx28evk/Makefile  |   49 ++++++++++
>  board/freescale/mx28evk/iomux.c   |  138 +++++++++++++++++++++++++++++
>  board/freescale/mx28evk/mx28evk.c |  170
> +++++++++++++++++++++++++++++++++++ board/freescale/mx28evk/u-boot.bd |  
> 14 +++
>  boards.cfg                        |    1 +
>  include/configs/mx28evk.h         |  176
> +++++++++++++++++++++++++++++++++++++ 7 files changed, 549 insertions(+),
> 0 deletions(-)
>  create mode 100644 board/freescale/mx28evk/Makefile
>  create mode 100644 board/freescale/mx28evk/iomux.c
>  create mode 100644 board/freescale/mx28evk/mx28evk.c
>  create mode 100644 board/freescale/mx28evk/u-boot.bd
>  create mode 100644 include/configs/mx28evk.h
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index a56ca10..72e1089 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
>  Fabio Estevam <fabio.estevam@freescale.com>
> 
>  	mx25pdk		i.MX25
> +	mx28evk		i.MX28
>  	mx31pdk		i.MX31
>  	mx53ard		i.MX53
>  	mx53smd		i.MX53
> diff --git a/board/freescale/mx28evk/Makefile
> b/board/freescale/mx28evk/Makefile new file mode 100644
> index 0000000..7459107
> --- /dev/null
> +++ b/board/freescale/mx28evk/Makefile
> @@ -0,0 +1,49 @@
> +#
> +# (C) Copyright 2000-2006
> +# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +# MA 02111-1307 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB	= $(obj)lib$(BOARD).o
> +
> +ifndef	CONFIG_SPL_BUILD
> +COBJS	:= mx28evk.o
> +else
> +COBJS	:= iomux.o
> +endif
> +
> +SRCS	:= $(COBJS:.o=.c)
> +OBJS	:= $(addprefix $(obj),$(COBJS))
> +
> +$(LIB):	$(obj).depend $(OBJS)
> +	$(call cmd_link_o_target, $(OBJS))
> +
> +all:	$(ALL)
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/freescale/mx28evk/iomux.c
> b/board/freescale/mx28evk/iomux.c new file mode 100644
> index 0000000..904e3f3
> --- /dev/null
> +++ b/board/freescale/mx28evk/iomux.c
> @@ -0,0 +1,138 @@
> +/*
> + * Freescale MX28EVK IOMUX setup
> + *
> + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
> + * on behalf of DENX Software Engineering GmbH
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <common.h>
> +#include <config.h>
> +#include <asm/io.h>
> +#include <asm/arch/iomux-mx28.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/sys_proto.h>
> +
> +#define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
> +#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
> +#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
> +
> +const iomux_cfg_t iomux_setup[] = {
> +	/* DUART */
> +	MX28_PAD_PWM0__DUART_RX,
> +	MX28_PAD_PWM1__DUART_TX,
> +
> +	/* MMC0 */
> +	MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
> +	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
> +		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
> +	MX28_PAD_SSP0_SCK__SSP0_SCK |
> +		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
> +	/* write protect */
> +	MX28_PAD_SSP1_SCK__GPIO_2_12,
> +	/* MMC0 slot power enable */
> +	MX28_PAD_PWM3__GPIO_3_28 |
> +		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
> +
> +	/* FEC0 */
> +	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
> +	/* FEC0 Enable */
> +	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
> +		(MXS_PAD_12MA | MXS_PAD_3V3),
> +	/* FEC0 Reset */
> +	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
> +		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
> +
> +	/* FEC1 */
> +	MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
> +	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
> +
> +	/* EMI */
> +	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
> +
> +	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
> +	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
> +};
> +
> +void board_init_ll(void)
> +{
> +	mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
> +}
> diff --git a/board/freescale/mx28evk/mx28evk.c
> b/board/freescale/mx28evk/mx28evk.c new file mode 100644
> index 0000000..542e806
> --- /dev/null
> +++ b/board/freescale/mx28evk/mx28evk.c
> @@ -0,0 +1,170 @@
> +/*
> + * Freescale MX28EVK board
> + *
> + * (C) Copyright 2011 Freescale Semiconductor, Inc.
> + *
> + * Author: Fabio Estevam <fabio.estevam@freescale.com>
> + *
> + * Based on m28evk.c:
> + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
> + * on behalf of DENX Software Engineering GmbH
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <common.h>
> +#include <asm/gpio.h>
> +#include <asm/io.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/iomux-mx28.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/sys_proto.h>
> +#include <linux/mii.h>
> +#include <miiphy.h>
> +#include <netdev.h>
> +#include <errno.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +/*
> + * Functions
> + */
> +int board_early_init_f(void)
> +{
> +	/* IO0 clock at 480MHz */
> +	mx28_set_ioclk(MXC_IOCLK0, 480000);
> +	/* IO1 clock at 480MHz */
> +	mx28_set_ioclk(MXC_IOCLK1, 480000);
> +
> +	/* SSP0 clock at 96MHz */
> +	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
> +	/* SSP2 clock at 96MHz */
> +	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
> +
> +	return 0;
> +}
> +
> +int dram_init(void)
> +{
> +	mx28_dram_init();
> +	return 0;
> +}
> +
> +int board_init(void)
> +{
> +	/* Adress of boot parameters */
> +	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
> +
> +	return 0;
> +}
> +
> +#ifdef	CONFIG_CMD_MMC
> +static int mx28evk_mmc_wp(int id)
> +{
> +	if (id != 0) {
> +		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
> +		return 1;
> +	}
> +
> +	return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
> +}
> +
> +int board_mmc_init(bd_t *bis)
> +{
> +	/* Configure WP as input */
> +	gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
> +
> +	/* Configure MMC0 Power Enable */
> +	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
> +
> +	return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
> +}
> +#endif
> +
> +#ifdef	CONFIG_CMD_NET
> +
> +#define	MII_OPMODE_STRAP_OVERRIDE	0x16
> +#define	MII_PHY_CTRL1			0x1e
> +#define	MII_PHY_CTRL2			0x1f
> +
> +int fecmxc_mii_postcall(int phy)
> +{
> +	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
> +	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
> +	if (phy == 3)
> +		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
> +	return 0;
> +}
> +
> +int board_eth_init(bd_t *bis)
> +{
> +	struct mx28_clkctrl_regs *clkctrl_regs =
> +		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
> +	struct eth_device *dev;
> +	int ret;
> +
> +	ret = cpu_eth_init(bis);
> +
> +	/* MX28EVK uses ENET_CLK PAD to drive FEC clock */
> +	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
> +					&clkctrl_regs->hw_clkctrl_enet);
> +
> +	/* Power-on FECs */
> +	gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
> +
> +	/* Reset FEC PHYs */
> +	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
> +	udelay(200);
> +	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
> +
> +	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
> +	if (ret) {
> +		puts("FEC MXS: Unable to init FEC0\n");
> +		return ret;
> +	}
> +
> +	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
> +	if (ret) {
> +		puts("FEC MXS: Unable to init FEC1\n");
> +		return ret;
> +	}
> +
> +	dev = eth_get_dev_by_name("FEC0");
> +	if (!dev) {
> +		puts("FEC MXS: Unable to get FEC0 device entry\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
> +	if (ret) {
> +		puts("FEC MXS: Unable to register FEC0 mii postcall\n");
> +		return ret;
> +	}
> +
> +	dev = eth_get_dev_by_name("FEC1");
> +	if (!dev) {
> +		puts("FEC MXS: Unable to get FEC1 device entry\n");
> +		return -EINVAL;
> +	}
> +
> +	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
> +	if (ret) {
> +		puts("FEC MXS: Unable to register FEC1 mii postcall\n");
> +		return ret;
> +	}
> +
> +	return ret;
> +}
> +
> +#endif
> diff --git a/board/freescale/mx28evk/u-boot.bd
> b/board/freescale/mx28evk/u-boot.bd new file mode 100644
> index 0000000..c60615a
> --- /dev/null
> +++ b/board/freescale/mx28evk/u-boot.bd
> @@ -0,0 +1,14 @@
> +sources {
> +	u_boot_spl="spl/u-boot-spl.bin";
> +	u_boot="u-boot.bin";
> +}
> +
> +section (0) {
> +	load u_boot_spl > 0x0000;
> +	load ivt (entry = 0x0014) > 0x8000;
> +	hab call 0x8000;
> +
> +	load u_boot > 0x40000100;
> +	load ivt (entry = 0x40000100) > 0x8000;
> +	hab call 0x8000;
> +}
> diff --git a/boards.cfg b/boards.cfg
> index 1e5b3e0..e859024 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -160,6 +160,7 @@ zmx25                        arm         arm926ejs  
> zmx25               syteco imx27lite                    arm        
> arm926ejs   imx27lite           logicpd        mx27 magnesium             
>       arm         arm926ejs   imx27lite           logicpd        mx27
> m28evk                       arm         arm926ejs   -                  
> denx           mx28 +mx28evk                      arm         arm926ejs  
> -                   freescale      mx28 nhk8815                      arm  
>       arm926ejs   nhk8815             st             nomadik
> nhk8815_onenand              arm         arm926ejs   nhk8815            
> st             nomadik       nhk8815:BOOT_ONENAND omap1610h2		     arm	
> arm926ejs   omap1610inn	 ti		omap	    omap1610inn:CS3_BOOT 
diff --git
> a/include/configs/mx28evk.h b/include/configs/mx28evk.h new file mode
> 100644
> index 0000000..5b8a1bf
> --- /dev/null
> +++ b/include/configs/mx28evk.h
> @@ -0,0 +1,176 @@
> +/*
> + * (C) Copyright 2011 Freescale Semiconductor, Inc.
> + * Author: Fabio Estevam <fabio.estevam@freescale.com>
> + *
> + * Based on m28evk.h:
> + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
> + * on behalf of DENX Software Engineering GmbH
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
> + * GNU General Public License for more details.
> + */
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include <asm/arch/regs-base.h>
> +
> +/*
> + * SoC configurations
> + */
> +#define	CONFIG_MX28				/* i.MX28 SoC */
> +#define	CONFIG_MXS_GPIO				/* GPIO control */
> +#define	CONFIG_SYS_HZ		1000		/* Ticks per second */
> +
> +#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
> +
> +#define	CONFIG_SYS_NO_FLASH
> +#define	CONFIG_SYS_ICACHE_OFF
> +#define	CONFIG_SYS_DCACHE_OFF
> +#define	CONFIG_BOARD_EARLY_INIT_F
> +#define	CONFIG_ARCH_CPU_INIT
> +#define	CONFIG_ARCH_MISC_INIT
> +
> +/*
> + * SPL
> + */
> +#define CONFIG_SPL
> +#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
> +#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
> +#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +
> +/*
> + * U-Boot Commands
> + */
> +#include <config_cmd_default.h>
> +#define	CONFIG_DISPLAY_CPUINFO
> +#define	CONFIG_DOS_PARTITION
> +#define CONFIG_CMD_FAT
> +
> +#define	CONFIG_CMD_CACHE
> +#define	CONFIG_CMD_DHCP
> +#define	CONFIG_CMD_GPIO
> +#define	CONFIG_CMD_MII
> +#define	CONFIG_CMD_MMC
> +#define	CONFIG_CMD_NET
> +#define	CONFIG_CMD_NFS
> +#define	CONFIG_CMD_PING
> +
> +/*
> + * Memory configurations
> + */
> +#define	CONFIG_NR_DRAM_BANKS		1		/* 1 bank of 
DRAM */
> +#define	PHYS_SDRAM_1			0x40000000	/* Base address 
*/
> +#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM 
*/
> +#define	CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack 
*/
> +#define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for 
malloc */
> +#define	CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start 
adr */
> +#define	CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test 
*/
> +#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
> +/* Point initial SP in SRAM so SPL can use it too. */
> +
> +#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
> +#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
> +
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +/*
> + * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
> + * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
> + * binary. In case there was more of this mess, 0x100 bytes are skipped.
> + */
> +#define	CONFIG_SYS_TEXT_BASE		0x40000100
> +
> +#define CONFIG_ENV_OVERWRITE
> +/*
> + * U-Boot general configurations
> + */
> +#define	CONFIG_SYS_LONGHELP
> +#define	CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
> +#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer 
size */
> +#define	CONFIG_SYS_PBSIZE	\
> +	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
> +						/* Print buffer size */
> +#define	CONFIG_SYS_MAXARGS	32		/* Max number of command 
args */
> +#define	CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
> +						/* Boot argument buffer size */
> +#define	CONFIG_VERSION_VARIABLE			/* U-BOOT version */
> +#define	CONFIG_AUTO_COMPLETE			/* Command auto complete 
*/
> +#define	CONFIG_CMDLINE_EDITING			/* Command history etc 
*/
> +#define	CONFIG_SYS_HUSH_PARSER
> +#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
> +
> +/*
> + * Serial Driver
> + */
> +#define	CONFIG_PL011_SERIAL
> +#define	CONFIG_PL011_CLOCK		24000000
> +#define	CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
> +#define	CONFIG_CONS_INDEX		0
> +#define	CONFIG_BAUDRATE			115200	/* Default baud rate */
> +#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 
115200 }
> +
> +/*
> + * MMC Driver
> + */
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_ENV_OFFSET	(256 * 1024)
> +#define CONFIG_ENV_SIZE		(16 * 1024)
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +#define CONFIG_CMD_SAVEENV
> +#ifdef	CONFIG_CMD_MMC
> +#define	CONFIG_MMC
> +#define	CONFIG_GENERIC_MMC
> +#define	CONFIG_MXS_MMC
> +#endif

Tabs vs. spaces, please fix globally.

M

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Veli-Pekka Peltola]

Hi Fabio,

On 12/16/2011 12:07 AM, Fabio Estevam wrote:
> Tested boot via SD card and by loading a kernel via TFTP through
> the FEC interface.

Have you any idea why this works from SD card but not by USB recovery 
using exactly same sb file?

By quick look it seems that control is not passed back to the ROM 
properly after SPL or ROM is unable to load/run U-Boot after SPL.

--
Veli-Pekka Peltola

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

On Fri, Dec 16, 2011 at 12:55 PM, Veli-Pekka Peltola
<veli-pekka.peltola@bluegiga.com> wrote:

> Have you any idea why this works from SD card but not by USB recovery using
> exactly same sb file?

Sorry, never tested this 'USB recovery' mode.

I can look at it after I finish the mx28evk patches.

Reagards,

Fabio Estevam

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Marek Vasut]

> Hi Fabio,
> 
> On 12/16/2011 12:07 AM, Fabio Estevam wrote:
> > Tested boot via SD card and by loading a kernel via TFTP through
> > the FEC interface.
> 
> Have you any idea why this works from SD card but not by USB recovery
> using exactly same sb file?
> 
> By quick look it seems that control is not passed back to the ROM
> properly after SPL or ROM is unable to load/run U-Boot after SPL.

What do you mean? The SPL only inits the hardware and then lets the bootrom do 
whatever it wants again with the next file in u-boot.bd.

[U-Boot] [PATCH v5 3/3] mx28evk: Add initial support for MX28EVK board

[Veli-Pekka Peltola]

Dear Marek Vasut,

On 12/17/2011 05:17 AM, Marek Vasut wrote:
>> Hi Fabio,
>>
>> On 12/16/2011 12:07 AM, Fabio Estevam wrote:
>>> Tested boot via SD card and by loading a kernel via TFTP through
>>> the FEC interface.
>>
>> Have you any idea why this works from SD card but not by USB recovery
>> using exactly same sb file?
>>
>> By quick look it seems that control is not passed back to the ROM
>> properly after SPL or ROM is unable to load/run U-Boot after SPL.
>
> What do you mean? The SPL only inits the hardware and then lets the bootrom do
> whatever it wants again with the next file in u-boot.bd.

U-Boot doesn't start up after SPL, that is what I see.

I don't have tools or knowledge to investigate this further but here are 
steps to replicate the issue:
1) make mx28evk_config
2) make u-boot.sb
3) set dip switches to usb0 bootmode
4) connect micro-USB cable
5) try to load u-boot.sb using mfgtool (Windows) or imx_hid_recovery 
(Linux) [1]

I tested USB powered mode and 5V wall adapter without difference.

--
Veli-Pekka Peltola

[1] 
http://git.pengutronix.de/?p=mxs-utils.git;a=commit;h=87692449099ae85922842f7f01acc0ab71e382d7