[net 0/5][pull request] Intel Wired LAN Driver Updates

[net 0/5][pull request] Intel Wired LAN Driver Updates

[Jeff Kirsher]

This series of patches contains fixes for ixgbe and e1000e.
This also contains the last bit for e1000 to support RXALL flag
from Ben Greear.

The following are changes since commit 01627d968c8b5e2810fe8c417b406b968297c236:
  Merge branch 'drm-fixes-intel' of git://people.freedesktop.org/~airlied/linux
and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net master

Ben Greear (1):
  e1000: Support RX-ALL flag.

Bruce Allan (1):
  e1000e: prevent oops when adapter is being closed and reset
    simultaneously

Matthew Vick (2):
  e1000e: Guarantee descriptor writeback flush success.
  e1000e: Minor comment clean-up.

Multanen, Eric W (1):
  ixgbe: driver fix for link flap

 drivers/net/ethernet/intel/e1000/e1000_main.c   |   26 ++++-
 drivers/net/ethernet/intel/e1000e/e1000.h       |    6 +
 drivers/net/ethernet/intel/e1000e/netdev.c      |   29 ++++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c |  164 +++++++++++------------
 4 files changed, 139 insertions(+), 86 deletions(-)

-- 
1.7.7.6

[net 1/5] ixgbe: driver fix for link flap

[Jeff Kirsher]

From: "Multanen, Eric W" <eric.w.multanen@intel.com>

Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.

Without this fix, the link could reset and result in
a link flap.

The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes.  The other
places where changes were detected previously can be removed.

Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c |  164 +++++++++++------------
 1 files changed, 80 insertions(+), 84 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c
index dde65f9..652e4b0 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c
@@ -44,62 +44,94 @@
 #define DCB_NO_HW_CHG   1  /* DCB configuration did not change */
 #define DCB_HW_CHG      2  /* DCB configuration changed, no reset */
 
-int ixgbe_copy_dcb_cfg(struct ixgbe_dcb_config *src_dcb_cfg,
-                       struct ixgbe_dcb_config *dst_dcb_cfg, int tc_max)
+int ixgbe_copy_dcb_cfg(struct ixgbe_dcb_config *scfg,
+		       struct ixgbe_dcb_config *dcfg, int tc_max)
 {
-	struct tc_configuration *src_tc_cfg = NULL;
-	struct tc_configuration *dst_tc_cfg = NULL;
-	int i;
+	struct tc_configuration *src = NULL;
+	struct tc_configuration *dst = NULL;
+	int i, j;
+	int tx = DCB_TX_CONFIG;
+	int rx = DCB_RX_CONFIG;
+	int changes = 0;
 
-	if (!src_dcb_cfg || !dst_dcb_cfg)
-		return -EINVAL;
+	if (!scfg || !dcfg)
+		return changes;
 
 	for (i = DCB_PG_ATTR_TC_0; i < tc_max + DCB_PG_ATTR_TC_0; i++) {
-		src_tc_cfg = &src_dcb_cfg->tc_config[i - DCB_PG_ATTR_TC_0];
-		dst_tc_cfg = &dst_dcb_cfg->tc_config[i - DCB_PG_ATTR_TC_0];
+		src = &scfg->tc_config[i - DCB_PG_ATTR_TC_0];
+		dst = &dcfg->tc_config[i - DCB_PG_ATTR_TC_0];
 
-		dst_tc_cfg->path[DCB_TX_CONFIG].prio_type =
-				src_tc_cfg->path[DCB_TX_CONFIG].prio_type;
+		if (dst->path[tx].prio_type != src->path[tx].prio_type) {
+			dst->path[tx].prio_type = src->path[tx].prio_type;
+			changes |= BIT_PG_TX;
+		}
 
-		dst_tc_cfg->path[DCB_TX_CONFIG].bwg_id =
-				src_tc_cfg->path[DCB_TX_CONFIG].bwg_id;
+		if (dst->path[tx].bwg_id != src->path[tx].bwg_id) {
+			dst->path[tx].bwg_id = src->path[tx].bwg_id;
+			changes |= BIT_PG_TX;
+		}
 
-		dst_tc_cfg->path[DCB_TX_CONFIG].bwg_percent =
-				src_tc_cfg->path[DCB_TX_CONFIG].bwg_percent;
+		if (dst->path[tx].bwg_percent != src->path[tx].bwg_percent) {
+			dst->path[tx].bwg_percent = src->path[tx].bwg_percent;
+			changes |= BIT_PG_TX;
+		}
 
-		dst_tc_cfg->path[DCB_TX_CONFIG].up_to_tc_bitmap =
-				src_tc_cfg->path[DCB_TX_CONFIG].up_to_tc_bitmap;
+		if (dst->path[tx].up_to_tc_bitmap !=
+				src->path[tx].up_to_tc_bitmap) {
+			dst->path[tx].up_to_tc_bitmap =
+				src->path[tx].up_to_tc_bitmap;
+			changes |= (BIT_PG_TX | BIT_PFC | BIT_APP_UPCHG);
+		}
 
-		dst_tc_cfg->path[DCB_RX_CONFIG].prio_type =
-				src_tc_cfg->path[DCB_RX_CONFIG].prio_type;
+		if (dst->path[rx].prio_type != src->path[rx].prio_type) {
+			dst->path[rx].prio_type = src->path[rx].prio_type;
+			changes |= BIT_PG_RX;
+		}
 
-		dst_tc_cfg->path[DCB_RX_CONFIG].bwg_id =
-				src_tc_cfg->path[DCB_RX_CONFIG].bwg_id;
+		if (dst->path[rx].bwg_id != src->path[rx].bwg_id) {
+			dst->path[rx].bwg_id = src->path[rx].bwg_id;
+			changes |= BIT_PG_RX;
+		}
 
-		dst_tc_cfg->path[DCB_RX_CONFIG].bwg_percent =
-				src_tc_cfg->path[DCB_RX_CONFIG].bwg_percent;
+		if (dst->path[rx].bwg_percent != src->path[rx].bwg_percent) {
+			dst->path[rx].bwg_percent = src->path[rx].bwg_percent;
+			changes |= BIT_PG_RX;
+		}
 
-		dst_tc_cfg->path[DCB_RX_CONFIG].up_to_tc_bitmap =
-				src_tc_cfg->path[DCB_RX_CONFIG].up_to_tc_bitmap;
+		if (dst->path[rx].up_to_tc_bitmap !=
+				src->path[rx].up_to_tc_bitmap) {
+			dst->path[rx].up_to_tc_bitmap =
+				src->path[rx].up_to_tc_bitmap;
+			changes |= (BIT_PG_RX | BIT_PFC | BIT_APP_UPCHG);
+		}
 	}
 
 	for (i = DCB_PG_ATTR_BW_ID_0; i < DCB_PG_ATTR_BW_ID_MAX; i++) {
-		dst_dcb_cfg->bw_percentage[DCB_TX_CONFIG]
-			[i-DCB_PG_ATTR_BW_ID_0] = src_dcb_cfg->bw_percentage
-				[DCB_TX_CONFIG][i-DCB_PG_ATTR_BW_ID_0];
-		dst_dcb_cfg->bw_percentage[DCB_RX_CONFIG]
-			[i-DCB_PG_ATTR_BW_ID_0] = src_dcb_cfg->bw_percentage
-				[DCB_RX_CONFIG][i-DCB_PG_ATTR_BW_ID_0];
+		j = i - DCB_PG_ATTR_BW_ID_0;
+		if (dcfg->bw_percentage[tx][j] != scfg->bw_percentage[tx][j]) {
+			dcfg->bw_percentage[tx][j] = scfg->bw_percentage[tx][j];
+			changes |= BIT_PG_TX;
+		}
+		if (dcfg->bw_percentage[rx][j] != scfg->bw_percentage[rx][j]) {
+			dcfg->bw_percentage[rx][j] = scfg->bw_percentage[rx][j];
+			changes |= BIT_PG_RX;
+		}
 	}
 
 	for (i = DCB_PFC_UP_ATTR_0; i < DCB_PFC_UP_ATTR_MAX; i++) {
-		dst_dcb_cfg->tc_config[i - DCB_PFC_UP_ATTR_0].dcb_pfc =
-			src_dcb_cfg->tc_config[i - DCB_PFC_UP_ATTR_0].dcb_pfc;
+		j = i - DCB_PFC_UP_ATTR_0;
+		if (dcfg->tc_config[j].dcb_pfc != scfg->tc_config[j].dcb_pfc) {
+			dcfg->tc_config[j].dcb_pfc = scfg->tc_config[j].dcb_pfc;
+			changes |= BIT_PFC;
+		}
 	}
 
-	dst_dcb_cfg->pfc_mode_enable = src_dcb_cfg->pfc_mode_enable;
+	if (dcfg->pfc_mode_enable != scfg->pfc_mode_enable) {
+		dcfg->pfc_mode_enable = scfg->pfc_mode_enable;
+		changes |= BIT_PFC;
+	}
 
-	return 0;
+	return changes;
 }
 
 static u8 ixgbe_dcbnl_get_state(struct net_device *netdev)
@@ -179,20 +211,6 @@ static void ixgbe_dcbnl_set_pg_tc_cfg_tx(struct net_device *netdev, int tc,
 	if (up_map != DCB_ATTR_VALUE_UNDEFINED)
 		adapter->temp_dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap =
 			up_map;
-
-	if ((adapter->temp_dcb_cfg.tc_config[tc].path[0].prio_type !=
-	     adapter->dcb_cfg.tc_config[tc].path[0].prio_type) ||
-	    (adapter->temp_dcb_cfg.tc_config[tc].path[0].bwg_id !=
-	     adapter->dcb_cfg.tc_config[tc].path[0].bwg_id) ||
-	    (adapter->temp_dcb_cfg.tc_config[tc].path[0].bwg_percent !=
-	     adapter->dcb_cfg.tc_config[tc].path[0].bwg_percent) ||
-	    (adapter->temp_dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap !=
-	     adapter->dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap))
-		adapter->dcb_set_bitmap |= BIT_PG_TX;
-
-	if (adapter->temp_dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap !=
-	     adapter->dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap)
-		adapter->dcb_set_bitmap |= BIT_PFC | BIT_APP_UPCHG;
 }
 
 static void ixgbe_dcbnl_set_pg_bwg_cfg_tx(struct net_device *netdev, int bwg_id,
@@ -201,10 +219,6 @@ static void ixgbe_dcbnl_set_pg_bwg_cfg_tx(struct net_device *netdev, int bwg_id,
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 
 	adapter->temp_dcb_cfg.bw_percentage[0][bwg_id] = bw_pct;
-
-	if (adapter->temp_dcb_cfg.bw_percentage[0][bwg_id] !=
-	    adapter->dcb_cfg.bw_percentage[0][bwg_id])
-		adapter->dcb_set_bitmap |= BIT_PG_TX;
 }
 
 static void ixgbe_dcbnl_set_pg_tc_cfg_rx(struct net_device *netdev, int tc,
@@ -223,20 +237,6 @@ static void ixgbe_dcbnl_set_pg_tc_cfg_rx(struct net_device *netdev, int tc,
 	if (up_map != DCB_ATTR_VALUE_UNDEFINED)
 		adapter->temp_dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap =
 			up_map;
-
-	if ((adapter->temp_dcb_cfg.tc_config[tc].path[1].prio_type !=
-	     adapter->dcb_cfg.tc_config[tc].path[1].prio_type) ||
-	    (adapter->temp_dcb_cfg.tc_config[tc].path[1].bwg_id !=
-	     adapter->dcb_cfg.tc_config[tc].path[1].bwg_id) ||
-	    (adapter->temp_dcb_cfg.tc_config[tc].path[1].bwg_percent !=
-	     adapter->dcb_cfg.tc_config[tc].path[1].bwg_percent) ||
-	    (adapter->temp_dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap !=
-	     adapter->dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap))
-		adapter->dcb_set_bitmap |= BIT_PG_RX;
-
-	if (adapter->temp_dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap !=
-	     adapter->dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap)
-		adapter->dcb_set_bitmap |= BIT_PFC;
 }
 
 static void ixgbe_dcbnl_set_pg_bwg_cfg_rx(struct net_device *netdev, int bwg_id,
@@ -245,10 +245,6 @@ static void ixgbe_dcbnl_set_pg_bwg_cfg_rx(struct net_device *netdev, int bwg_id,
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 
 	adapter->temp_dcb_cfg.bw_percentage[1][bwg_id] = bw_pct;
-
-	if (adapter->temp_dcb_cfg.bw_percentage[1][bwg_id] !=
-	    adapter->dcb_cfg.bw_percentage[1][bwg_id])
-		adapter->dcb_set_bitmap |= BIT_PG_RX;
 }
 
 static void ixgbe_dcbnl_get_pg_tc_cfg_tx(struct net_device *netdev, int tc,
@@ -298,10 +294,8 @@ static void ixgbe_dcbnl_set_pfc_cfg(struct net_device *netdev, int priority,
 
 	adapter->temp_dcb_cfg.tc_config[priority].dcb_pfc = setting;
 	if (adapter->temp_dcb_cfg.tc_config[priority].dcb_pfc !=
-	    adapter->dcb_cfg.tc_config[priority].dcb_pfc) {
-		adapter->dcb_set_bitmap |= BIT_PFC;
+	    adapter->dcb_cfg.tc_config[priority].dcb_pfc)
 		adapter->temp_dcb_cfg.pfc_mode_enable = true;
-	}
 }
 
 static void ixgbe_dcbnl_get_pfc_cfg(struct net_device *netdev, int priority,
@@ -336,7 +330,8 @@ static void ixgbe_dcbnl_devreset(struct net_device *dev)
 static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
-	int ret, i;
+	int ret = DCB_NO_HW_CHG;
+	int i;
 #ifdef IXGBE_FCOE
 	struct dcb_app app = {
 			      .selector = DCB_APP_IDTYPE_ETHTYPE,
@@ -355,12 +350,13 @@ static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
 
 	/* Fail command if not in CEE mode */
 	if (!(adapter->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
-		return 1;
+		return ret;
 
-	ret = ixgbe_copy_dcb_cfg(&adapter->temp_dcb_cfg, &adapter->dcb_cfg,
-				 MAX_TRAFFIC_CLASS);
-	if (ret)
-		return DCB_NO_HW_CHG;
+	adapter->dcb_set_bitmap |= ixgbe_copy_dcb_cfg(&adapter->temp_dcb_cfg,
+						      &adapter->dcb_cfg,
+						      MAX_TRAFFIC_CLASS);
+	if (!adapter->dcb_set_bitmap)
+		return ret;
 
 	if (adapter->dcb_cfg.pfc_mode_enable) {
 		switch (adapter->hw.mac.type) {
@@ -420,6 +416,8 @@ static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
 
 		for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++)
 			netdev_set_prio_tc_map(netdev, i, prio_tc[i]);
+
+		ret = DCB_HW_CHG_RST;
 	}
 
 	if (adapter->dcb_set_bitmap & BIT_PFC) {
@@ -430,7 +428,8 @@ static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
 				     DCB_TX_CONFIG, prio_tc);
 		ixgbe_dcb_unpack_pfc(&adapter->dcb_cfg, &pfc_en);
 		ixgbe_dcb_hw_pfc_config(&adapter->hw, pfc_en, prio_tc);
-		ret = DCB_HW_CHG;
+		if (ret != DCB_HW_CHG_RST)
+			ret = DCB_HW_CHG;
 	}
 
 	if (adapter->dcb_cfg.pfc_mode_enable)
@@ -531,9 +530,6 @@ static void ixgbe_dcbnl_setpfcstate(struct net_device *netdev, u8 state)
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 
 	adapter->temp_dcb_cfg.pfc_mode_enable = state;
-	if (adapter->temp_dcb_cfg.pfc_mode_enable !=
-		adapter->dcb_cfg.pfc_mode_enable)
-		adapter->dcb_set_bitmap |= BIT_PFC;
 }
 
 /**
-- 
1.7.7.6

[net 2/5] e1000: Support RX-ALL flag.

[Jeff Kirsher]

From: Ben Greear <greearb@candelatech.com>

This allows the NIC to receive errored frames (bad FCS, etc)
and pass them up the stack.  This can be useful when using
sniffers.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000/e1000_main.c |   26 ++++++++++++++++++++++++-
 1 files changed, 25 insertions(+), 1 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c
index 4348b6f..3d712f2 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_main.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_main.c
@@ -827,9 +827,10 @@ static int e1000_set_features(struct net_device *netdev,
 	if (changed & NETIF_F_HW_VLAN_RX)
 		e1000_vlan_mode(netdev, features);
 
-	if (!(changed & NETIF_F_RXCSUM))
+	if (!(changed & (NETIF_F_RXCSUM | NETIF_F_RXALL)))
 		return 0;
 
+	netdev->features = features;
 	adapter->rx_csum = !!(features & NETIF_F_RXCSUM);
 
 	if (netif_running(netdev))
@@ -1074,6 +1075,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 
 	netdev->features |= netdev->hw_features;
 	netdev->hw_features |= NETIF_F_RXCSUM;
+	netdev->hw_features |= NETIF_F_RXALL;
 	netdev->hw_features |= NETIF_F_RXFCS;
 
 	if (pci_using_dac) {
@@ -1841,6 +1843,22 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 			break;
 	}
 
+	/* This is useful for sniffing bad packets. */
+	if (adapter->netdev->features & NETIF_F_RXALL) {
+		/* UPE and MPE will be handled by normal PROMISC logic
+		 * in e1000e_set_rx_mode */
+		rctl |= (E1000_RCTL_SBP | /* Receive bad packets */
+			 E1000_RCTL_BAM | /* RX All Bcast Pkts */
+			 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */
+
+		rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */
+			  E1000_RCTL_DPF | /* Allow filtered pause */
+			  E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */
+		/* Do not mess with E1000_CTRL_VME, it affects transmit as well,
+		 * and that breaks VLANs.
+		 */
+	}
+
 	ew32(RCTL, rctl);
 }
 
@@ -4057,6 +4075,8 @@ static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
 				                       irq_flags);
 				length--;
 			} else {
+				if (netdev->features & NETIF_F_RXALL)
+					goto process_skb;
 				/* recycle both page and skb */
 				buffer_info->skb = skb;
 				/* an error means any chain goes out the window
@@ -4069,6 +4089,7 @@ static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
 		}
 
 #define rxtop rx_ring->rx_skb_top
+process_skb:
 		if (!(status & E1000_RXD_STAT_EOP)) {
 			/* this descriptor is only the beginning (or middle) */
 			if (!rxtop) {
@@ -4276,12 +4297,15 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
 				                       flags);
 				length--;
 			} else {
+				if (netdev->features & NETIF_F_RXALL)
+					goto process_skb;
 				/* recycle */
 				buffer_info->skb = skb;
 				goto next_desc;
 			}
 		}
 
+process_skb:
 		total_rx_bytes += (length - 4); /* don't count FCS */
 		total_rx_packets++;
 
-- 
1.7.7.6

[net 3/5] e1000e: prevent oops when adapter is being closed and reset simultaneously

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h  |    6 ++++++
 drivers/net/ethernet/intel/e1000e/netdev.c |    9 +++++++++
 2 files changed, 15 insertions(+), 0 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 86cdd47..b83897f 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -161,6 +161,12 @@ struct e1000_info;
 /* Time to wait before putting the device into D3 if there's no link (in ms). */
 #define LINK_TIMEOUT		100
 
+/*
+ * Count for polling __E1000_RESET condition every 10-20msec.
+ * Experimentation has shown the reset can take approximately 210msec.
+ */
+#define E1000_CHECK_RESET_COUNT		25
+
 #define DEFAULT_RDTR			0
 #define DEFAULT_RADV			8
 #define BURST_RDTR			0x20
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 2c38a65..6878601 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3968,6 +3968,10 @@ static int e1000_close(struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct pci_dev *pdev = adapter->pdev;
+	int count = E1000_CHECK_RESET_COUNT;
+
+	while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
+		usleep_range(10000, 20000);
 
 	WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
 
@@ -5472,6 +5476,11 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake,
 	netif_device_detach(netdev);
 
 	if (netif_running(netdev)) {
+		int count = E1000_CHECK_RESET_COUNT;
+
+		while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
+			usleep_range(10000, 20000);
+
 		WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
 		e1000e_down(adapter);
 		e1000_free_irq(adapter);
-- 
1.7.7.6

[net 4/5] e1000e: Guarantee descriptor writeback flush success.

[Jeff Kirsher]

From: Matthew Vick <matthew.vick@intel.com>

In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c |   17 +++++++++++++++++
 1 files changed, 17 insertions(+), 0 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 6878601..19ab215 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1059,6 +1059,13 @@ static void e1000_print_hw_hang(struct work_struct *work)
 		ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
 		/* execute the writes immediately */
 		e1e_flush();
+		/*
+		 * Due to rare timing issues, write to TIDV again to ensure
+		 * the write is successful
+		 */
+		ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
+		/* execute the writes immediately */
+		e1e_flush();
 		adapter->tx_hang_recheck = true;
 		return;
 	}
@@ -3616,6 +3623,16 @@ static void e1000e_flush_descriptors(struct e1000_adapter *adapter)
 
 	/* execute the writes immediately */
 	e1e_flush();
+
+	/*
+	 * due to rare timing issues, write to TIDV/RDTR again to ensure the
+	 * write is successful
+	 */
+	ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
+	ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD);
+
+	/* execute the writes immediately */
+	e1e_flush();
 }
 
 static void e1000e_update_stats(struct e1000_adapter *adapter);
-- 
1.7.7.6

[net 5/5] e1000e: Minor comment clean-up.

[Jeff Kirsher]

From: Matthew Vick <matthew.vick@intel.com>

Move the first phrase of a multi-line comment to the second line.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 19ab215..5d1ca1c 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1053,7 +1053,8 @@ static void e1000_print_hw_hang(struct work_struct *work)
 
 	if (!adapter->tx_hang_recheck &&
 	    (adapter->flags2 & FLAG2_DMA_BURST)) {
-		/* May be block on write-back, flush and detect again
+		/*
+		 * May be block on write-back, flush and detect again
 		 * flush pending descriptor writebacks to memory
 		 */
 		ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
-- 
1.7.7.6

Re: [net 2/5] e1000: Support RX-ALL flag.

[David Miller]

From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Tue,  3 Apr 2012 15:18:06 -0700

> From: Ben Greear <greearb@candelatech.com>
> 
> This allows the NIC to receive errored frames (bad FCS, etc)
> and pass them up the stack.  This can be useful when using
> sniffers.
> 
> Signed-off-by: Ben Greear <greearb@candelatech.com>
> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is not a bug fix, therefore it's not appropriate for 'net'

Re: [net 5/5] e1000e: Minor comment clean-up.

[David Miller]

From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Tue,  3 Apr 2012 15:18:09 -0700

> From: Matthew Vick <matthew.vick@intel.com>
> 
> Move the first phrase of a multi-line comment to the second line.
> 
> Signed-off-by: Matthew Vick <matthew.vick@intel.com>
> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Also not appropriate for 'net'

Re: [net 5/5] e1000e: Minor comment clean-up.

[Jeff Kirsher]

[-- Attachment #1: Type: text/plain, Size: 558 bytes --]

On Tue, 2012-04-03 at 18:19 -0400, David Miller wrote:
> From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> Date: Tue,  3 Apr 2012 15:18:09 -0700
> 
> > From: Matthew Vick <matthew.vick@intel.com>
> > 
> > Move the first phrase of a multi-line comment to the second line.
> > 
> > Signed-off-by: Matthew Vick <matthew.vick@intel.com>
> > Tested-by: Aaron Brown <aaron.f.brown@intel.com>
> > Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> 
> Also not appropriate for 'net'

Ok, I will drop patch 2 & 5 from the series and re-post.

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]