* [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates.
@ 2012-05-08 12:41 Jayachandran C
2012-05-08 12:41 ` [PATCH 01/14] MIPS: Netlogic: Fix PCIX irq on XLR chips Jayachandran C
` (13 more replies)
0 siblings, 14 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:41 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
This is an update for the patcheset I had posted earlier.
The changes from v1 are:
- re-write the MSI fix a bit make it look better [and also update
commit message - noted by sshtylyov@mvista.com]
- Add two more patches for XLP - one to probe FDT SoC devices, and
another to add a few IRQs which will be used for SoC devices.
[Description of the patchset from v1]
Fixes and updates for the next merge window. This includes
- PCI fixs for XLR/XLS
- I2C, Flash and USB platform drivers for XLR/XLS
- XLP SMP code update and clean up
- XLP TLB size fix
- XLP USB and PCI changes.
Let me know if there are any comments.
Thanks,
JC.
Ganesan Ramalingam (5):
MIPS: Netlogic: MSI enable fix for XLS
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: Add XLP SoC devices in FDT
Jayachandran C (9):
MIPS: Netlogic: Fix PCIX irq on XLR chips
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Fix TLB size of boot CPU.
MIPS: Netlogic: Update comments in smpboot.S
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Add IRQ mappings for more devices
arch/mips/Kconfig | 3 +-
arch/mips/configs/nlm_xlr_defconfig | 4 +
.../mips/include/asm/netlogic/xlp-hal/cpucontrol.h | 4 +-
arch/mips/include/asm/netlogic/xlp-hal/iomap.h | 5 +-
arch/mips/include/asm/netlogic/xlp-hal/pcibus.h | 76 ++++++
arch/mips/include/asm/netlogic/xlp-hal/pic.h | 4 +
arch/mips/include/asm/netlogic/xlp-hal/usb.h | 64 +++++
arch/mips/include/asm/netlogic/xlp-hal/xlp.h | 17 +-
arch/mips/include/asm/netlogic/xlr/bridge.h | 104 +++++++++
arch/mips/include/asm/netlogic/xlr/flash.h | 55 +++++
arch/mips/include/asm/netlogic/xlr/gpio.h | 59 ++---
arch/mips/netlogic/common/smpboot.S | 159 ++++++++-----
arch/mips/netlogic/xlp/Makefile | 1 +
arch/mips/netlogic/xlp/nlm_hal.c | 52 +++++
arch/mips/netlogic/xlp/platform.c | 2 +-
arch/mips/netlogic/xlp/setup.c | 24 +-
arch/mips/netlogic/xlp/usb-init.c | 124 ++++++++++
arch/mips/netlogic/xlr/Makefile | 2 +-
arch/mips/netlogic/xlr/platform-flash.c | 220 +++++++++++++++++
arch/mips/netlogic/xlr/platform.c | 140 +++++++++++
arch/mips/netlogic/xlr/setup.c | 2 +-
arch/mips/pci/Makefile | 1 +
arch/mips/pci/pci-xlp.c | 247 ++++++++++++++++++++
arch/mips/pci/pci-xlr.c | 65 ++++--
24 files changed, 1326 insertions(+), 108 deletions(-)
create mode 100644 arch/mips/include/asm/netlogic/xlp-hal/pcibus.h
create mode 100644 arch/mips/include/asm/netlogic/xlp-hal/usb.h
create mode 100644 arch/mips/include/asm/netlogic/xlr/bridge.h
create mode 100644 arch/mips/include/asm/netlogic/xlr/flash.h
create mode 100644 arch/mips/netlogic/xlp/usb-init.c
create mode 100644 arch/mips/netlogic/xlr/platform-flash.c
create mode 100644 arch/mips/pci/pci-xlp.c
--
1.7.9.5
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 01/14] MIPS: Netlogic: Fix PCIX irq on XLR chips
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
@ 2012-05-08 12:41 ` Jayachandran C
2012-05-08 12:41 ` [PATCH 02/14] MIPS: Netlogic: MSI enable fix for XLS Jayachandran C
` (12 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:41 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
The correct irq is PIC_PCIX_IRQ
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/pci/pci-xlr.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/mips/pci/pci-xlr.c b/arch/mips/pci/pci-xlr.c
index 1644805..50ff4dc 100644
--- a/arch/mips/pci/pci-xlr.c
+++ b/arch/mips/pci/pci-xlr.c
@@ -327,7 +327,7 @@ static int __init pcibios_init(void)
}
} else {
/* XLR PCI controller ACK */
- irq_set_handler_data(PIC_PCIE_XLSB0_LINK3_IRQ, xlr_pci_ack);
+ irq_set_handler_data(PIC_PCIX_IRQ, xlr_pci_ack);
}
return 0;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 02/14] MIPS: Netlogic: MSI enable fix for XLS
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
2012-05-08 12:41 ` [PATCH 01/14] MIPS: Netlogic: Fix PCIX irq on XLR chips Jayachandran C
@ 2012-05-08 12:41 ` Jayachandran C
2012-05-08 12:41 ` [PATCH 03/14] MIPS: Netlogic: Remove unused pcibios_fixups Jayachandran C
` (11 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:41 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Ganesan Ramalingam, Jayachandran C
From: Ganesan Ramalingam <ganesanr@broadcom.com>
MSI interrupts do not work on XLS after commit a776c49
( "PCI: msi: Disable msi interrupts when we initialize a pci device" )
because the change disables MSI interrupts on the XLS PCIe bridges
during the PCI enumeration.
Fix this by enabling MSI interrupts on the bridge in the
arch_setup_msi_irq() function. A new function xls_get_pcie_link()
has been introduced to get the PCI device corresponding to the
top level PCIe bridge on which MSI has to be enabled.
Also, update get_irq_vector() to use the new xls_get_pcie_link()
function and PCI_SLOT() macro for determining the IRQ of PCI devices.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/pci/pci-xlr.c | 59 +++++++++++++++++++++++++++++++++++++++--------
1 file changed, 50 insertions(+), 9 deletions(-)
diff --git a/arch/mips/pci/pci-xlr.c b/arch/mips/pci/pci-xlr.c
index 50ff4dc..172af1c 100644
--- a/arch/mips/pci/pci-xlr.c
+++ b/arch/mips/pci/pci-xlr.c
@@ -41,6 +41,7 @@
#include <linux/irq.h>
#include <linux/irqdesc.h>
#include <linux/console.h>
+#include <linux/pci_regs.h>
#include <asm/io.h>
@@ -156,35 +157,55 @@ struct pci_controller nlm_pci_controller = {
.io_offset = 0x00000000UL,
};
+/*
+ * The top level PCIe links on the XLS PCIe controller appear as
+ * bridges. Given a device, this function finds which link it is
+ * on.
+ */
+static struct pci_dev *xls_get_pcie_link(const struct pci_dev *dev)
+{
+ struct pci_bus *bus, *p;
+
+ /* Find the bridge on bus 0 */
+ bus = dev->bus;
+ for (p = bus->parent; p && p->number != 0; p = p->parent)
+ bus = p;
+
+ return p ? bus->self : NULL;
+}
+
static int get_irq_vector(const struct pci_dev *dev)
{
+ struct pci_dev *lnk;
+
if (!nlm_chip_is_xls())
- return PIC_PCIX_IRQ; /* for XLR just one IRQ*/
+ return PIC_PCIX_IRQ; /* for XLR just one IRQ */
/*
* For XLS PCIe, there is an IRQ per Link, find out which
* link the device is on to assign interrupts
- */
- if (dev->bus->self == NULL)
+ */
+ lnk = xls_get_pcie_link(dev);
+ if (lnk == NULL)
return 0;
- switch (dev->bus->self->devfn) {
- case 0x0:
+ switch (PCI_SLOT(lnk->devfn)) {
+ case 0:
return PIC_PCIE_LINK0_IRQ;
- case 0x8:
+ case 1:
return PIC_PCIE_LINK1_IRQ;
- case 0x10:
+ case 2:
if (nlm_chip_is_xls_b())
return PIC_PCIE_XLSB0_LINK2_IRQ;
else
return PIC_PCIE_LINK2_IRQ;
- case 0x18:
+ case 3:
if (nlm_chip_is_xls_b())
return PIC_PCIE_XLSB0_LINK3_IRQ;
else
return PIC_PCIE_LINK3_IRQ;
}
- WARN(1, "Unexpected devfn %d\n", dev->bus->self->devfn);
+ WARN(1, "Unexpected devfn %d\n", lnk->devfn);
return 0;
}
@@ -202,7 +223,27 @@ void arch_teardown_msi_irq(unsigned int irq)
int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc)
{
struct msi_msg msg;
+ struct pci_dev *lnk;
int irq, ret;
+ u16 val;
+
+ /* MSI not supported on XLR */
+ if (!nlm_chip_is_xls())
+ return 1;
+
+ /*
+ * Enable MSI on the XLS PCIe controller bridge which was disabled
+ * at enumeration, the bridge MSI capability is at 0x50
+ */
+ lnk = xls_get_pcie_link(dev);
+ if (lnk == NULL)
+ return 1;
+
+ pci_read_config_word(lnk, 0x50 + PCI_MSI_FLAGS, &val);
+ if ((val & PCI_MSI_FLAGS_ENABLE) == 0) {
+ val |= PCI_MSI_FLAGS_ENABLE;
+ pci_write_config_word(lnk, 0x50 + PCI_MSI_FLAGS, val);
+ }
irq = get_irq_vector(dev);
if (irq <= 0)
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 03/14] MIPS: Netlogic: Remove unused pcibios_fixups
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
2012-05-08 12:41 ` [PATCH 01/14] MIPS: Netlogic: Fix PCIX irq on XLR chips Jayachandran C
2012-05-08 12:41 ` [PATCH 02/14] MIPS: Netlogic: MSI enable fix for XLS Jayachandran C
@ 2012-05-08 12:41 ` Jayachandran C
2012-05-08 12:41 ` [PATCH 04/14] MIPS: Netlogic: Fix TLB size of boot CPU Jayachandran C
` (10 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:41 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
This global is unneeded, and seems to be carried over from ancient
code.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/pci/pci-xlr.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/mips/pci/pci-xlr.c b/arch/mips/pci/pci-xlr.c
index 172af1c..18af021 100644
--- a/arch/mips/pci/pci-xlr.c
+++ b/arch/mips/pci/pci-xlr.c
@@ -375,7 +375,3 @@ static int __init pcibios_init(void)
}
arch_initcall(pcibios_init);
-
-struct pci_fixup pcibios_fixups[] = {
- {0}
-};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 04/14] MIPS: Netlogic: Fix TLB size of boot CPU.
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (2 preceding siblings ...)
2012-05-08 12:41 ` [PATCH 03/14] MIPS: Netlogic: Remove unused pcibios_fixups Jayachandran C
@ 2012-05-08 12:41 ` Jayachandran C
2012-05-08 12:41 ` [PATCH 05/14] MIPS: Netlogic: Update comments in smpboot.S Jayachandran C
` (9 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:41 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
Starting other threads in the core will change the number of
TLB entries of a CPU. Re-calculate current_cpu_data.tlbsize
on the boot cpu after enabling and waking up other threads.
The secondary CPUs do not need this logic because the threads
are enabled on the secondary cores at wakeup and before cpu_probe.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/netlogic/xlp/setup.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/arch/mips/netlogic/xlp/setup.c b/arch/mips/netlogic/xlp/setup.c
index acb677a..b3df7c2 100644
--- a/arch/mips/netlogic/xlp/setup.c
+++ b/arch/mips/netlogic/xlp/setup.c
@@ -82,8 +82,10 @@ void __init prom_free_prom_memory(void)
void xlp_mmu_init(void)
{
+ /* enable extended TLB and Large Fixed TLB */
write_c0_config6(read_c0_config6() | 0x24);
- current_cpu_data.tlbsize = ((read_c0_config6() >> 16) & 0xffff) + 1;
+
+ /* set page mask of Fixed TLB in config7 */
write_c0_config7(PM_DEFAULT_MASK >>
(13 + (ffz(PM_DEFAULT_MASK >> 13) / 2)));
}
@@ -100,6 +102,10 @@ void __init prom_init(void)
nlm_common_ebase = read_c0_ebase() & (~((1 << 12) - 1));
#ifdef CONFIG_SMP
nlm_wakeup_secondary_cpus(0xffffffff);
+
+ /* update TLB size after waking up threads */
+ current_cpu_data.tlbsize = ((read_c0_config6() >> 16) & 0xffff) + 1;
+
register_smp_ops(&nlm_smp_ops);
#endif
}
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 05/14] MIPS: Netlogic: Update comments in smpboot.S
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (3 preceding siblings ...)
2012-05-08 12:41 ` [PATCH 04/14] MIPS: Netlogic: Fix TLB size of boot CPU Jayachandran C
@ 2012-05-08 12:41 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 06/14] MIPS: Netlogic: SMP wakeup code update Jayachandran C
` (8 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:41 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
No change in logic, comments update and whitespace cleanup.
* A few comments in the file were in assembler style and the rest
int C style, convert all of them to C style.
* Mark workarounds for Ax silicon with a macro XLP_AX_WORKAROUND
* Whitespace fixes - use tabs consistently
* rename __config_lsu macro to xlp_config_lsu
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/netlogic/common/smpboot.S | 112 +++++++++++++++++++----------------
1 file changed, 61 insertions(+), 51 deletions(-)
diff --git a/arch/mips/netlogic/common/smpboot.S b/arch/mips/netlogic/common/smpboot.S
index c138b1a..bfe9060 100644
--- a/arch/mips/netlogic/common/smpboot.S
+++ b/arch/mips/netlogic/common/smpboot.S
@@ -54,28 +54,36 @@
XLP_IO_SYS_OFFSET(node) + XLP_IO_PCI_HDRSZ + \
SYS_CPU_NONCOHERENT_MODE * 4
-.macro __config_lsu
- li t0, LSU_DEFEATURE
- mfcr t1, t0
+#define XLP_AX_WORKAROUND /* enable Ax silicon workarounds */
- lui t2, 0x4080 /* Enable Unaligned Access, L2HPE */
- or t1, t1, t2
- li t2, ~0xe /* S1RCM */
+/* Enable XLP features and workarounds in the LSU */
+.macro xlp_config_lsu
+ li t0, LSU_DEFEATURE
+ mfcr t1, t0
+
+ lui t2, 0x4080 /* Enable Unaligned Access, L2HPE */
+ or t1, t1, t2
+#ifdef XLP_AX_WORKAROUND
+ li t2, ~0xe /* S1RCM */
and t1, t1, t2
+#endif
mtcr t1, t0
- li t0, SCHED_DEFEATURE
- lui t1, 0x0100 /* Experimental: Disable BRU accepting ALU ops */
- mtcr t1, t0
+#ifdef XLP_AX_WORKAROUND
+ li t0, SCHED_DEFEATURE
+ lui t1, 0x0100 /* Disable BRU accepting ALU ops */
+ mtcr t1, t0
+#endif
.endm
/*
- * The cores can come start when they are woken up. This is also the NMI
- * entry, so check that first.
+ * This is the code that will be copied to the reset entry point for
+ * XLR and XLP. The XLP cores start here when they are woken up. This
+ * is also the NMI entry point.
*
- * The data corresponding to reset is stored at RESET_DATA_PHYS location,
- * this will have the thread mask (used when core is woken up) and the
- * current NMI handler in case we reached here for an NMI.
+ * The data corresponding to reset/NMI is stored at RESET_DATA_PHYS
+ * location, this will have the thread mask (used when core is woken up)
+ * and the current NMI handler in case we reached here for an NMI.
*
* When a core or thread is newly woken up, it loops in a 'wait'. When
* the CPU really needs waking up, we send an NMI to it, with the NMI
@@ -89,12 +97,12 @@
FEXPORT(nlm_reset_entry)
dmtc0 k0, $22, 6
dmtc0 k1, $22, 7
- mfc0 k0, CP0_STATUS
- li k1, 0x80000
- and k1, k0, k1
- beqz k1, 1f /* go to real reset entry */
+ mfc0 k0, CP0_STATUS
+ li k1, 0x80000
+ and k1, k0, k1
+ beqz k1, 1f /* go to real reset entry */
nop
- li k1, CKSEG1ADDR(RESET_DATA_PHYS) /* NMI */
+ li k1, CKSEG1ADDR(RESET_DATA_PHYS) /* NMI */
ld k0, BOOT_NMI_HANDLER(k1)
jr k0
nop
@@ -114,21 +122,23 @@ FEXPORT(nlm_reset_entry)
li t2, SYS_CPU_COHERENT_BASE(0)
add t2, t2, t3 /* t2 <- SYS offset for node */
lw t1, 0(t2)
- and t1, t1, t0
- sw t1, 0(t2)
+ and t1, t1, t0
+ sw t1, 0(t2)
/* read back to ensure complete */
- lw t1, 0(t2)
+ lw t1, 0(t2)
sync
/* Configure LSU on Non-0 Cores. */
- __config_lsu
+ xlp_config_lsu
+ /* FALL THROUGH */
/*
* Wake up sibling threads from the initial thread in
* a core.
*/
EXPORT(nlm_boot_siblings)
+ /* Enable hw threads by writing to MAP_THREADMODE of the core */
li t0, CKSEG1ADDR(RESET_DATA_PHYS)
lw t1, BOOT_THREAD_MODE(t0) /* t1 <- thread mode */
li t0, ((CPU_BLOCKID_MAP << 8) | MAP_THREADMODE)
@@ -139,24 +149,24 @@ EXPORT(nlm_boot_siblings)
/*
* The new hardware thread starts at the next instruction
* For all the cases other than core 0 thread 0, we will
- * jump to the secondary wait function.
- */
+ * jump to the secondary wait function.
+ */
mfc0 v0, CP0_EBASE, 1
andi v0, 0x7f /* v0 <- node/core */
-#if 1
- /* A0 errata - Write MMU_SETUP after changing thread mode register. */
+ /* Init MMU in the first thread after changing THREAD_MODE
+ * register (Ax Errata?)
+ */
andi v1, v0, 0x3 /* v1 <- thread id */
bnez v1, 2f
nop
- li t0, MMU_SETUP
- li t1, 0
- mtcr t1, t0
+ li t0, MMU_SETUP
+ li t1, 0
+ mtcr t1, t0
ehb
-#endif
-2: beqz v0, 4f
+2: beqz v0, 4f /* boot cpu (cpuid == 0)? */
nop
/* setup status reg */
@@ -183,9 +193,9 @@ EXPORT(nlm_boot_siblings)
* For the boot CPU, we have to restore registers and
* return
*/
-4: dmfc0 t0, $4, 2 /* restore SP from UserLocal */
+4: dmfc0 t0, $4, 2 /* restore SP from UserLocal */
li t1, 0xfadebeef
- dmtc0 t1, $4, 2 /* restore SP from UserLocal */
+ dmtc0 t1, $4, 2 /* restore SP from UserLocal */
PTR_SUBU sp, t0, PT_SIZE
RESTORE_ALL
jr ra
@@ -193,7 +203,7 @@ EXPORT(nlm_boot_siblings)
EXPORT(nlm_reset_entry_end)
FEXPORT(xlp_boot_core0_siblings) /* "Master" cpu starts from here */
- __config_lsu
+ xlp_config_lsu
dmtc0 sp, $4, 2 /* SP saved in UserLocal */
SAVE_ALL
sync
@@ -234,36 +244,36 @@ END(nlm_boot_secondary_cpus)
*/
__CPUINIT
NESTED(nlm_rmiboot_preboot, 16, sp)
- mfc0 t0, $15, 1 # read ebase
- andi t0, 0x1f # t0 has the processor_id()
- andi t2, t0, 0x3 # thread no
- sll t0, 2 # offset in cpu array
+ mfc0 t0, $15, 1 /* read ebase */
+ andi t0, 0x1f /* t0 has the processor_id() */
+ andi t2, t0, 0x3 /* thread num */
+ sll t0, 2 /* offset in cpu array */
- PTR_LA t1, nlm_cpu_ready # mark CPU ready
+ PTR_LA t1, nlm_cpu_ready /* mark CPU ready */
PTR_ADDU t1, t0
li t3, 1
sw t3, 0(t1)
- bnez t2, 1f # skip thread programming
- nop # for non zero hw threads
+ bnez t2, 1f /* skip thread programming */
+ nop /* for thread id != 0 */
/*
- * MMU setup only for first thread in core
+ * XLR MMU setup only for first thread in core
*/
li t0, 0x400
mfcr t1, t0
- li t2, 6 # XLR thread mode mask
+ li t2, 6 /* XLR thread mode mask */
nor t3, t2, zero
- and t2, t1, t2 # t2 - current thread mode
+ and t2, t1, t2 /* t2 - current thread mode */
li v0, CKSEG1ADDR(RESET_DATA_PHYS)
- lw v1, BOOT_THREAD_MODE(v0) # v1 - new thread mode
+ lw v1, BOOT_THREAD_MODE(v0) /* v1 - new thread mode */
sll v1, 1
- beq v1, t2, 1f # same as request value
- nop # nothing to do */
+ beq v1, t2, 1f /* same as request value */
+ nop /* nothing to do */
- and t2, t1, t3 # mask out old thread mode
- or t1, t2, v1 # put in new value
- mtcr t1, t0 # update core control
+ and t2, t1, t3 /* mask out old thread mode */
+ or t1, t2, v1 /* put in new value */
+ mtcr t1, t0 /* update core control */
1: wait
j 1b
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 06/14] MIPS: Netlogic: SMP wakeup code update
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (4 preceding siblings ...)
2012-05-08 12:41 ` [PATCH 05/14] MIPS: Netlogic: Update comments in smpboot.S Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 07/14] MIPS: Netlogic: Remove NETLOGIC_ prefix Jayachandran C
` (7 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
Update for core intialization code. Initialize status register
after receiving NMI for CPU wakeup. Add the low level L1D flush
code before enabling threads in core.
Also convert the ehb to _ehb so that it works under more GCC
versions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
.../mips/include/asm/netlogic/xlp-hal/cpucontrol.h | 4 +-
arch/mips/netlogic/common/smpboot.S | 47 +++++++++++++++++---
2 files changed, 45 insertions(+), 6 deletions(-)
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h b/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h
index bf7d41d..7b63a6b 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h
@@ -47,7 +47,9 @@
#define CPU_BLOCKID_MAP 10
#define LSU_DEFEATURE 0x304
-#define LSU_CERRLOG_REGID 0x09
+#define LSU_DEBUG_ADDR 0x305
+#define LSU_DEBUG_DATA0 0x306
+#define LSU_CERRLOG_REGID 0x309
#define SCHED_DEFEATURE 0x700
/* Offsets of interest from the 'MAP' Block */
diff --git a/arch/mips/netlogic/common/smpboot.S b/arch/mips/netlogic/common/smpboot.S
index bfe9060..aa86590 100644
--- a/arch/mips/netlogic/common/smpboot.S
+++ b/arch/mips/netlogic/common/smpboot.S
@@ -77,6 +77,38 @@
.endm
/*
+ * Low level L1 d-cache flush for core, needs to be called before
+ * threads are enabled
+ */
+.macro xlp_flush_l1_dcache
+ li t0, LSU_DEBUG_DATA0
+ li t1, LSU_DEBUG_ADDR
+ li t2, 0 /* index */
+ li t3, 0x200 /* loop count, 512 sets */
+1:
+ sll v0, t2, 5
+ mtcr zero, t0
+ ori v1, v0, 0x3 /* way0 | write_enable | write_active */
+ mtcr v1, t1
+2:
+ mfcr v1, t1
+ andi v1, 0x1 /* wait for write_active == 0 */
+ bnez v1, 2b
+ nop
+ mtcr zero, t0
+ ori v1, v0, 0x7 /* way1 | write_enable | write_active */
+ mtcr v1, t1
+3:
+ mfcr v1, t1
+ andi v1, 0x1 /* wait for write_active == 0 */
+ bnez v1, 3b
+ nop
+ addi t2, 1
+ bne t3, t2, 1b
+ nop
+.endm
+
+/*
* This is the code that will be copied to the reset entry point for
* XLR and XLP. The XLP cores start here when they are woken up. This
* is also the NMI entry point.
@@ -138,6 +170,8 @@ FEXPORT(nlm_reset_entry)
* a core.
*/
EXPORT(nlm_boot_siblings)
+ /* core L1D flush before enable threads */
+ xlp_flush_l1_dcache
/* Enable hw threads by writing to MAP_THREADMODE of the core */
li t0, CKSEG1ADDR(RESET_DATA_PHYS)
lw t1, BOOT_THREAD_MODE(t0) /* t1 <- thread mode */
@@ -164,16 +198,13 @@ EXPORT(nlm_boot_siblings)
li t0, MMU_SETUP
li t1, 0
mtcr t1, t0
- ehb
+ _ehb
2: beqz v0, 4f /* boot cpu (cpuid == 0)? */
nop
/* setup status reg */
- mfc0 t1, CP0_STATUS
- li t0, ST0_BEV
- or t1, t0
- xor t1, t0
+ move t1, zero
#ifdef CONFIG_64BIT
ori t1, ST0_KX
#endif
@@ -220,6 +251,12 @@ FEXPORT(xlp_boot_core0_siblings) /* "Master" cpu starts from here */
__CPUINIT
NESTED(nlm_boot_secondary_cpus, 16, sp)
+ /* Initialize CP0 Status */
+ move t1, zero
+#ifdef CONFIG_64BIT
+ ori t1, ST0_KX
+#endif
+ mtc0 t1, CP0_STATUS
PTR_LA t1, nlm_next_sp
PTR_L sp, 0(t1)
PTR_LA t1, nlm_next_gp
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 07/14] MIPS: Netlogic: Remove NETLOGIC_ prefix
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (5 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 06/14] MIPS: Netlogic: SMP wakeup code update Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 08/14] MIPS: Netlogic: Platform changes for XLS USB Jayachandran C
` (6 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
Remove NETLOGIC_ prefix from gpio register definitions, this will
bring it in-line with the other Netlogic headers.
Having NETLOGIC prefix here is misleading because these are XLR/XLS
specific register definitions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/include/asm/netlogic/xlr/gpio.h | 59 +++++++++++++++--------------
arch/mips/netlogic/xlr/setup.c | 2 +-
2 files changed, 31 insertions(+), 30 deletions(-)
diff --git a/arch/mips/include/asm/netlogic/xlr/gpio.h b/arch/mips/include/asm/netlogic/xlr/gpio.h
index 51f6ad4..8492e83 100644
--- a/arch/mips/include/asm/netlogic/xlr/gpio.h
+++ b/arch/mips/include/asm/netlogic/xlr/gpio.h
@@ -35,39 +35,40 @@
#ifndef _ASM_NLM_GPIO_H
#define _ASM_NLM_GPIO_H
-#define NETLOGIC_GPIO_INT_EN_REG 0
-#define NETLOGIC_GPIO_INPUT_INVERSION_REG 1
-#define NETLOGIC_GPIO_IO_DIR_REG 2
-#define NETLOGIC_GPIO_IO_DATA_WR_REG 3
-#define NETLOGIC_GPIO_IO_DATA_RD_REG 4
+#define GPIO_INT_EN_REG 0
+#define GPIO_INPUT_INVERSION_REG 1
+#define GPIO_IO_DIR_REG 2
+#define GPIO_IO_DATA_WR_REG 3
+#define GPIO_IO_DATA_RD_REG 4
-#define NETLOGIC_GPIO_SWRESET_REG 8
-#define NETLOGIC_GPIO_DRAM1_CNTRL_REG 9
-#define NETLOGIC_GPIO_DRAM1_RATIO_REG 10
-#define NETLOGIC_GPIO_DRAM1_RESET_REG 11
-#define NETLOGIC_GPIO_DRAM1_STATUS_REG 12
-#define NETLOGIC_GPIO_DRAM2_CNTRL_REG 13
-#define NETLOGIC_GPIO_DRAM2_RATIO_REG 14
-#define NETLOGIC_GPIO_DRAM2_RESET_REG 15
-#define NETLOGIC_GPIO_DRAM2_STATUS_REG 16
+#define GPIO_SWRESET_REG 8
+#define GPIO_DRAM1_CNTRL_REG 9
+#define GPIO_DRAM1_RATIO_REG 10
+#define GPIO_DRAM1_RESET_REG 11
+#define GPIO_DRAM1_STATUS_REG 12
+#define GPIO_DRAM2_CNTRL_REG 13
+#define GPIO_DRAM2_RATIO_REG 14
+#define GPIO_DRAM2_RESET_REG 15
+#define GPIO_DRAM2_STATUS_REG 16
-#define NETLOGIC_GPIO_PWRON_RESET_CFG_REG 21
-#define NETLOGIC_GPIO_BIST_ALL_GO_STATUS_REG 24
-#define NETLOGIC_GPIO_BIST_CPU_GO_STATUS_REG 25
-#define NETLOGIC_GPIO_BIST_DEV_GO_STATUS_REG 26
+#define GPIO_PWRON_RESET_CFG_REG 21
+#define GPIO_BIST_ALL_GO_STATUS_REG 24
+#define GPIO_BIST_CPU_GO_STATUS_REG 25
+#define GPIO_BIST_DEV_GO_STATUS_REG 26
-#define NETLOGIC_GPIO_FUSE_BANK_REG 35
-#define NETLOGIC_GPIO_CPU_RESET_REG 40
-#define NETLOGIC_GPIO_RNG_REG 43
+#define GPIO_FUSE_BANK_REG 35
+#define GPIO_CPU_RESET_REG 40
+#define GPIO_RNG_REG 43
-#define NETLOGIC_PWRON_RESET_PCMCIA_BOOT 17
-#define NETLOGIC_GPIO_LED_BITMAP 0x1700000
-#define NETLOGIC_GPIO_LED_0_SHIFT 20
-#define NETLOGIC_GPIO_LED_1_SHIFT 24
+#define PWRON_RESET_PCMCIA_BOOT 17
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_RESET 0x01
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_HARD_RESET 0x02
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_SOFT_RESET 0x03
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_MAIN 0x04
+#define GPIO_LED_BITMAP 0x1700000
+#define GPIO_LED_0_SHIFT 20
+#define GPIO_LED_1_SHIFT 24
+
+#define GPIO_LED_OUTPUT_CODE_RESET 0x01
+#define GPIO_LED_OUTPUT_CODE_HARD_RESET 0x02
+#define GPIO_LED_OUTPUT_CODE_SOFT_RESET 0x03
+#define GPIO_LED_OUTPUT_CODE_MAIN 0x04
#endif
diff --git a/arch/mips/netlogic/xlr/setup.c b/arch/mips/netlogic/xlr/setup.c
index c9d066d..81b1d31 100644
--- a/arch/mips/netlogic/xlr/setup.c
+++ b/arch/mips/netlogic/xlr/setup.c
@@ -85,7 +85,7 @@ static void nlm_linux_exit(void)
gpiobase = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET);
/* trigger a chip reset by writing 1 to GPIO_SWRESET_REG */
- nlm_write_reg(gpiobase, NETLOGIC_GPIO_SWRESET_REG, 1);
+ nlm_write_reg(gpiobase, GPIO_SWRESET_REG, 1);
for ( ; ; )
cpu_wait();
}
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 08/14] MIPS: Netlogic: Platform changes for XLS USB
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (6 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 07/14] MIPS: Netlogic: Remove NETLOGIC_ prefix Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 09/14] MIPS: Netlogic: Platform NAND/NOR flash support Jayachandran C
` (5 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
Add USB initialization code, setup resources and add USB platform
driver in mips/netlogic/xlr/platform.c.
Add USB support for XLR/XLS platform in Kconfig.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/Kconfig | 2 +
arch/mips/netlogic/xlr/platform.c | 89 +++++++++++++++++++++++++++++++++++++
2 files changed, 91 insertions(+)
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index ce30e2f..b3811dd 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -780,6 +780,8 @@ config NLM_XLR_BOARD
select ZONE_DMA if 64BIT
select SYNC_R4K
select SYS_HAS_EARLY_PRINTK
+ select USB_ARCH_HAS_OHCI if USB_SUPPORT
+ select USB_ARCH_HAS_EHCI if USB_SUPPORT
help
Support for systems based on Netlogic XLR and XLS processors.
Say Y here if you have a XLR or XLS based board.
diff --git a/arch/mips/netlogic/xlr/platform.c b/arch/mips/netlogic/xlr/platform.c
index eab64b4..cb0ab63 100644
--- a/arch/mips/netlogic/xlr/platform.c
+++ b/arch/mips/netlogic/xlr/platform.c
@@ -97,3 +97,92 @@ static int __init nlm_uart_init(void)
}
arch_initcall(nlm_uart_init);
+
+#ifdef CONFIG_USB
+/* Platform USB devices, only on XLS chips */
+static u64 xls_usb_dmamask = ~(u32)0;
+#define USB_PLATFORM_DEV(n, i, irq) \
+ { \
+ .name = n, \
+ .id = i, \
+ .num_resources = 2, \
+ .dev = { \
+ .dma_mask = &xls_usb_dmamask, \
+ .coherent_dma_mask = 0xffffffff, \
+ }, \
+ .resource = (struct resource[]) { \
+ { \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ { \
+ .start = irq, \
+ .end = irq, \
+ .flags = IORESOURCE_IRQ, \
+ }, \
+ }, \
+ }
+
+static struct platform_device xls_usb_ehci_device =
+ USB_PLATFORM_DEV("ehci-xls", 0, PIC_USB_IRQ);
+static struct platform_device xls_usb_ohci_device_0 =
+ USB_PLATFORM_DEV("ohci-xls-0", 1, PIC_USB_IRQ);
+static struct platform_device xls_usb_ohci_device_1 =
+ USB_PLATFORM_DEV("ohci-xls-1", 2, PIC_USB_IRQ);
+
+static struct platform_device *xls_platform_devices[] = {
+ &xls_usb_ehci_device,
+ &xls_usb_ohci_device_0,
+ &xls_usb_ohci_device_1,
+};
+
+int xls_platform_usb_init(void)
+{
+ uint64_t usb_mmio, gpio_mmio;
+ unsigned long memres;
+ uint32_t val;
+
+ if (!nlm_chip_is_xls())
+ return 0;
+
+ gpio_mmio = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET);
+ usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_1_OFFSET);
+
+ /* Clear Rogue Phy INTs */
+ nlm_write_reg(usb_mmio, 49, 0x10000000);
+ /* Enable all interrupts */
+ nlm_write_reg(usb_mmio, 50, 0x1f000000);
+
+ /* Enable ports */
+ nlm_write_reg(usb_mmio, 1, 0x07000500);
+
+ val = nlm_read_reg(gpio_mmio, 21);
+ if (((val >> 22) & 0x01) == 0) {
+ pr_info("Detected USB Device mode - Not supported!\n");
+ nlm_write_reg(usb_mmio, 0, 0x01000000);
+ return 0;
+ }
+
+ pr_info("Detected USB Host mode - Adding XLS USB devices.\n");
+ /* Clear reset, host mode */
+ nlm_write_reg(usb_mmio, 0, 0x02000000);
+
+ /* Memory resource for various XLS usb ports */
+ usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_0_OFFSET);
+ memres = CPHYSADDR((unsigned long)usb_mmio);
+ xls_usb_ehci_device.resource[0].start = memres;
+ xls_usb_ehci_device.resource[0].end = memres + 0x400 - 1;
+
+ memres += 0x400;
+ xls_usb_ohci_device_0.resource[0].start = memres;
+ xls_usb_ohci_device_0.resource[0].end = memres + 0x400 - 1;
+
+ memres += 0x400;
+ xls_usb_ohci_device_1.resource[0].start = memres;
+ xls_usb_ohci_device_1.resource[0].end = memres + 0x400 - 1;
+
+ return platform_add_devices(xls_platform_devices,
+ ARRAY_SIZE(xls_platform_devices));
+}
+
+arch_initcall(xls_platform_usb_init);
+#endif
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 09/14] MIPS: Netlogic: Platform NAND/NOR flash support
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (7 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 08/14] MIPS: Netlogic: Platform changes for XLS USB Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 10/14] MIPS: Netlogic: Platform changes for XLR/XLS I2C Jayachandran C
` (4 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Ganesan Ramalingam, Jayachandran C
From: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Changes to add support for the boot NOR flash on XLR boards and the
boot NAND/NOR flash drivers on the XLS boards.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/include/asm/netlogic/xlr/bridge.h | 104 +++++++++++++
arch/mips/include/asm/netlogic/xlr/flash.h | 55 +++++++
arch/mips/netlogic/xlr/Makefile | 2 +-
arch/mips/netlogic/xlr/platform-flash.c | 220 +++++++++++++++++++++++++++
4 files changed, 380 insertions(+), 1 deletion(-)
create mode 100644 arch/mips/include/asm/netlogic/xlr/bridge.h
create mode 100644 arch/mips/include/asm/netlogic/xlr/flash.h
create mode 100644 arch/mips/netlogic/xlr/platform-flash.c
diff --git a/arch/mips/include/asm/netlogic/xlr/bridge.h b/arch/mips/include/asm/netlogic/xlr/bridge.h
new file mode 100644
index 0000000..2d02428
--- /dev/null
+++ b/arch/mips/include/asm/netlogic/xlr/bridge.h
@@ -0,0 +1,104 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _ASM_NLM_BRIDGE_H_
+#define _ASM_NLM_BRIDGE_H_
+
+#define BRIDGE_DRAM_0_BAR 0
+#define BRIDGE_DRAM_1_BAR 1
+#define BRIDGE_DRAM_2_BAR 2
+#define BRIDGE_DRAM_3_BAR 3
+#define BRIDGE_DRAM_4_BAR 4
+#define BRIDGE_DRAM_5_BAR 5
+#define BRIDGE_DRAM_6_BAR 6
+#define BRIDGE_DRAM_7_BAR 7
+#define BRIDGE_DRAM_CHN_0_MTR_0_BAR 8
+#define BRIDGE_DRAM_CHN_0_MTR_1_BAR 9
+#define BRIDGE_DRAM_CHN_0_MTR_2_BAR 10
+#define BRIDGE_DRAM_CHN_0_MTR_3_BAR 11
+#define BRIDGE_DRAM_CHN_0_MTR_4_BAR 12
+#define BRIDGE_DRAM_CHN_0_MTR_5_BAR 13
+#define BRIDGE_DRAM_CHN_0_MTR_6_BAR 14
+#define BRIDGE_DRAM_CHN_0_MTR_7_BAR 15
+#define BRIDGE_DRAM_CHN_1_MTR_0_BAR 16
+#define BRIDGE_DRAM_CHN_1_MTR_1_BAR 17
+#define BRIDGE_DRAM_CHN_1_MTR_2_BAR 18
+#define BRIDGE_DRAM_CHN_1_MTR_3_BAR 19
+#define BRIDGE_DRAM_CHN_1_MTR_4_BAR 20
+#define BRIDGE_DRAM_CHN_1_MTR_5_BAR 21
+#define BRIDGE_DRAM_CHN_1_MTR_6_BAR 22
+#define BRIDGE_DRAM_CHN_1_MTR_7_BAR 23
+#define BRIDGE_CFG_BAR 24
+#define BRIDGE_PHNX_IO_BAR 25
+#define BRIDGE_FLASH_BAR 26
+#define BRIDGE_SRAM_BAR 27
+#define BRIDGE_HTMEM_BAR 28
+#define BRIDGE_HTINT_BAR 29
+#define BRIDGE_HTPIC_BAR 30
+#define BRIDGE_HTSM_BAR 31
+#define BRIDGE_HTIO_BAR 32
+#define BRIDGE_HTCFG_BAR 33
+#define BRIDGE_PCIXCFG_BAR 34
+#define BRIDGE_PCIXMEM_BAR 35
+#define BRIDGE_PCIXIO_BAR 36
+#define BRIDGE_DEVICE_MASK 37
+#define BRIDGE_AERR_INTR_LOG1 38
+#define BRIDGE_AERR_INTR_LOG2 39
+#define BRIDGE_AERR_INTR_LOG3 40
+#define BRIDGE_AERR_DEV_STAT 41
+#define BRIDGE_AERR1_LOG1 42
+#define BRIDGE_AERR1_LOG2 43
+#define BRIDGE_AERR1_LOG3 44
+#define BRIDGE_AERR1_DEV_STAT 45
+#define BRIDGE_AERR_INTR_EN 46
+#define BRIDGE_AERR_UPG 47
+#define BRIDGE_AERR_CLEAR 48
+#define BRIDGE_AERR1_CLEAR 49
+#define BRIDGE_SBE_COUNTS 50
+#define BRIDGE_DBE_COUNTS 51
+#define BRIDGE_BITERR_INT_EN 52
+
+#define BRIDGE_SYS2IO_CREDITS 53
+#define BRIDGE_EVNT_CNT_CTRL1 54
+#define BRIDGE_EVNT_COUNTER1 55
+#define BRIDGE_EVNT_CNT_CTRL2 56
+#define BRIDGE_EVNT_COUNTER2 57
+#define BRIDGE_RESERVED1 58
+
+#define BRIDGE_DEFEATURE 59
+#define BRIDGE_SCRATCH0 60
+#define BRIDGE_SCRATCH1 61
+#define BRIDGE_SCRATCH2 62
+#define BRIDGE_SCRATCH3 63
+
+#endif
diff --git a/arch/mips/include/asm/netlogic/xlr/flash.h b/arch/mips/include/asm/netlogic/xlr/flash.h
new file mode 100644
index 0000000..f8aca54
--- /dev/null
+++ b/arch/mips/include/asm/netlogic/xlr/flash.h
@@ -0,0 +1,55 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _ASM_NLM_FLASH_H_
+#define _ASM_NLM_FLASH_H_
+
+#define FLASH_CSBASE_ADDR(cs) (cs)
+#define FLASH_CSADDR_MASK(cs) (0x10 + (cs))
+#define FLASH_CSDEV_PARM(cs) (0x20 + (cs))
+#define FLASH_CSTIME_PARMA(cs) (0x30 + (cs))
+#define FLASH_CSTIME_PARMB(cs) (0x40 + (cs))
+
+#define FLASH_INT_MASK 0x50
+#define FLASH_INT_STATUS 0x60
+#define FLASH_ERROR_STATUS 0x70
+#define FLASH_ERROR_ADDR 0x80
+
+#define FLASH_NAND_CLE(cs) (0x90 + (cs))
+#define FLASH_NAND_ALE(cs) (0xa0 + (cs))
+
+#define FLASH_NAND_CSDEV_PARAM 0x000041e6
+#define FLASH_NAND_CSTIME_PARAMA 0x4f400e22
+#define FLASH_NAND_CSTIME_PARAMB 0x000083cf
+
+#endif
diff --git a/arch/mips/netlogic/xlr/Makefile b/arch/mips/netlogic/xlr/Makefile
index f01e4d7..c287dea 100644
--- a/arch/mips/netlogic/xlr/Makefile
+++ b/arch/mips/netlogic/xlr/Makefile
@@ -1,2 +1,2 @@
-obj-y += setup.o platform.o
+obj-y += setup.o platform.o platform-flash.o
obj-$(CONFIG_SMP) += wakeup.o
diff --git a/arch/mips/netlogic/xlr/platform-flash.c b/arch/mips/netlogic/xlr/platform-flash.c
new file mode 100644
index 0000000..340ab16
--- /dev/null
+++ b/arch/mips/netlogic/xlr/platform-flash.c
@@ -0,0 +1,220 @@
+/*
+ * Copyright 2011, Netlogic Microsystems.
+ * Copyright 2004, Matt Porter <mporter@kernel.crashing.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/resource.h>
+#include <linux/spi/flash.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/netlogic/haldefs.h>
+#include <asm/netlogic/xlr/iomap.h>
+#include <asm/netlogic/xlr/flash.h>
+#include <asm/netlogic/xlr/bridge.h>
+#include <asm/netlogic/xlr/gpio.h>
+#include <asm/netlogic/xlr/xlr.h>
+
+/*
+ * Default NOR partition layout
+ */
+static struct mtd_partition xlr_nor_parts[] = {
+ {
+ .name = "User FS",
+ .offset = 0x800000,
+ .size = MTDPART_SIZ_FULL,
+ }
+};
+
+/*
+ * Default NAND partition layout
+ */
+static struct mtd_partition xlr_nand_parts[] = {
+ {
+ .name = "Root Filesystem",
+ .offset = 64 * 64 * 2048,
+ .size = 432 * 64 * 2048,
+ },
+ {
+ .name = "Home Filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+/* Use PHYSMAP flash for NOR */
+struct physmap_flash_data xlr_nor_data = {
+ .width = 2,
+ .parts = xlr_nor_parts,
+ .nr_parts = ARRAY_SIZE(xlr_nor_parts),
+};
+
+static struct resource xlr_nor_res[] = {
+ {
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device xlr_nor_dev = {
+ .name = "physmap-flash",
+ .dev = {
+ .platform_data = &xlr_nor_data,
+ },
+ .num_resources = ARRAY_SIZE(xlr_nor_res),
+ .resource = xlr_nor_res,
+};
+
+const char *xlr_part_probes[] = { "cmdlinepart", NULL };
+
+/*
+ * Use "gen_nand" driver for NAND flash
+ *
+ * There seems to be no way to store a private pointer containing
+ * platform specific info in gen_nand drivier. We will use a global
+ * struct for now, since we currently have only one NAND chip per board.
+ */
+struct xlr_nand_flash_priv {
+ int cs;
+ uint64_t flash_mmio;
+};
+
+static struct xlr_nand_flash_priv nand_priv;
+
+static void xlr_nand_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ if (ctrl & NAND_CLE)
+ nlm_write_reg(nand_priv.flash_mmio,
+ FLASH_NAND_CLE(nand_priv.cs), cmd);
+ else if (ctrl & NAND_ALE)
+ nlm_write_reg(nand_priv.flash_mmio,
+ FLASH_NAND_ALE(nand_priv.cs), cmd);
+}
+
+struct platform_nand_data xlr_nand_data = {
+ .chip = {
+ .nr_chips = 1,
+ .nr_partitions = ARRAY_SIZE(xlr_nand_parts),
+ .chip_delay = 50,
+ .partitions = xlr_nand_parts,
+ .part_probe_types = xlr_part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = xlr_nand_ctrl,
+ },
+};
+
+static struct resource xlr_nand_res[] = {
+ {
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device xlr_nand_dev = {
+ .name = "gen_nand",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(xlr_nand_res),
+ .resource = xlr_nand_res,
+ .dev = {
+ .platform_data = &xlr_nand_data,
+ }
+};
+
+/*
+ * XLR/XLS supports upto 8 devices on its FLASH interface. The value in
+ * FLASH_BAR (on the MEM/IO bridge) gives the base for mapping all the
+ * flash devices.
+ * Under this, each flash device has an offset and size given by the
+ * CSBASE_ADDR and CSBASE_MASK registers for the device.
+ *
+ * The CSBASE_ registers are expected to be setup by the bootloader.
+ */
+static void setup_flash_resource(uint64_t flash_mmio,
+ uint64_t flash_map_base, int cs, struct resource *res)
+{
+ u32 base, mask;
+
+ base = nlm_read_reg(flash_mmio, FLASH_CSBASE_ADDR(cs));
+ mask = nlm_read_reg(flash_mmio, FLASH_CSADDR_MASK(cs));
+
+ res->start = flash_map_base + ((unsigned long)base << 16);
+ res->end = res->start + (mask + 1) * 64 * 1024;
+}
+
+static int __init xlr_flash_init(void)
+{
+ uint64_t gpio_mmio, flash_mmio, flash_map_base;
+ u32 gpio_resetcfg, flash_bar;
+ int cs, boot_nand, boot_nor;
+
+ /* Flash address bits 39:24 is in bridge flash BAR */
+ flash_bar = nlm_read_reg(nlm_io_base, BRIDGE_FLASH_BAR);
+ flash_map_base = (flash_bar & 0xffff0000) << 8;
+
+ gpio_mmio = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET);
+ flash_mmio = nlm_mmio_base(NETLOGIC_IO_FLASH_OFFSET);
+
+ /* Get the chip reset config */
+ gpio_resetcfg = nlm_read_reg(gpio_mmio, GPIO_PWRON_RESET_CFG_REG);
+
+ /* Check for boot flash type */
+ boot_nor = boot_nand = 0;
+ if (nlm_chip_is_xls()) {
+ /* On XLS, check boot from NAND bit (GPIO reset reg bit 16) */
+ if (gpio_resetcfg & (1 << 16))
+ boot_nand = 1;
+
+ /* check boot from PCMCIA, (GPIO reset reg bit 15 */
+ if ((gpio_resetcfg & (1 << 15)) == 0)
+ boot_nor = 1; /* not set, booted from NOR */
+ } else { /* XLR */
+ /* check boot from PCMCIA (bit 16 in GPIO reset on XLR) */
+ if ((gpio_resetcfg & (1 << 16)) == 0)
+ boot_nor = 1; /* not set, booted from NOR */
+ }
+
+ /* boot flash at chip select 0 */
+ cs = 0;
+
+ if (boot_nand) {
+ nand_priv.cs = cs;
+ nand_priv.flash_mmio = flash_mmio;
+ setup_flash_resource(flash_mmio, flash_map_base, cs,
+ xlr_nand_res);
+
+ /* Initialize NAND flash at CS 0 */
+ nlm_write_reg(flash_mmio, FLASH_CSDEV_PARM(cs),
+ FLASH_NAND_CSDEV_PARAM);
+ nlm_write_reg(flash_mmio, FLASH_CSTIME_PARMA(cs),
+ FLASH_NAND_CSTIME_PARAMA);
+ nlm_write_reg(flash_mmio, FLASH_CSTIME_PARMB(cs),
+ FLASH_NAND_CSTIME_PARAMB);
+
+ pr_info("ChipSelect %d: NAND Flash %pR\n", cs, xlr_nand_res);
+ return platform_device_register(&xlr_nand_dev);
+ }
+
+ if (boot_nor) {
+ setup_flash_resource(flash_mmio, flash_map_base, cs,
+ xlr_nor_res);
+ pr_info("ChipSelect %d: NOR Flash %pR\n", cs, xlr_nor_res);
+ return platform_device_register(&xlr_nor_dev);
+ }
+ return 0;
+}
+
+arch_initcall(xlr_flash_init);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 10/14] MIPS: Netlogic: Platform changes for XLR/XLS I2C
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (8 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 09/14] MIPS: Netlogic: Platform NAND/NOR flash support Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 11/14] MIPS: Netlogic: XLP PCIe controller support Jayachandran C
` (3 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
Add platform code for XLR/XLS I2C controller and devices. Add
devices on the I2C bus on the XLR/XLS developement boards.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/configs/nlm_xlr_defconfig | 4 +++
arch/mips/netlogic/xlr/platform.c | 51 +++++++++++++++++++++++++++++++++++
2 files changed, 55 insertions(+)
diff --git a/arch/mips/configs/nlm_xlr_defconfig b/arch/mips/configs/nlm_xlr_defconfig
index d0b857d..138f698 100644
--- a/arch/mips/configs/nlm_xlr_defconfig
+++ b/arch/mips/configs/nlm_xlr_defconfig
@@ -367,6 +367,10 @@ CONFIG_SERIAL_8250_RSA=y
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_TIMERIOMEM=m
CONFIG_RAW_DRIVER=m
+CONFIG_I2C=y
+CONFIG_I2C_XLR=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_DS1374=y
# CONFIG_HWMON is not set
# CONFIG_VGA_CONSOLE is not set
# CONFIG_HID_SUPPORT is not set
diff --git a/arch/mips/netlogic/xlr/platform.c b/arch/mips/netlogic/xlr/platform.c
index cb0ab63..71b44d8 100644
--- a/arch/mips/netlogic/xlr/platform.c
+++ b/arch/mips/netlogic/xlr/platform.c
@@ -14,6 +14,7 @@
#include <linux/resource.h>
#include <linux/serial_8250.h>
#include <linux/serial_reg.h>
+#include <linux/i2c.h>
#include <asm/netlogic/haldefs.h>
#include <asm/netlogic/xlr/iomap.h>
@@ -186,3 +187,53 @@ int xls_platform_usb_init(void)
arch_initcall(xls_platform_usb_init);
#endif
+
+#ifdef CONFIG_I2C
+static struct i2c_board_info nlm_i2c_board_info1[] __initdata = {
+ /* All XLR boards have this RTC and Max6657 Temp Chip */
+ [0] = {
+ .type = "ds1374",
+ .addr = 0x68
+ },
+ [1] = {
+ .type = "lm90",
+ .addr = 0x4c
+ },
+};
+
+static struct resource i2c_resources[] = {
+ [0] = {
+ .start = 0, /* filled at init */
+ .end = 0,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device nlm_xlr_i2c_1 = {
+ .name = "xlr-i2cbus",
+ .id = 1,
+ .num_resources = 1,
+ .resource = i2c_resources,
+};
+
+static int __init nlm_i2c_init(void)
+{
+ int err = 0;
+ unsigned int offset;
+
+ /* I2C bus 0 does not have any useful devices, configure only bus 1 */
+ offset = NETLOGIC_IO_I2C_1_OFFSET;
+ nlm_xlr_i2c_1.resource[0].start = CPHYSADDR(nlm_mmio_base(offset));
+ nlm_xlr_i2c_1.resource[0].end = nlm_xlr_i2c_1.resource[0].start + 0xfff;
+
+ platform_device_register(&nlm_xlr_i2c_1);
+
+ err = i2c_register_board_info(1, nlm_i2c_board_info1,
+ ARRAY_SIZE(nlm_i2c_board_info1));
+ if (err < 0)
+ pr_err("nlm-i2c: cannot register board I2C devices\n");
+ return err;
+}
+
+arch_initcall(nlm_i2c_init);
+#endif
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 11/14] MIPS: Netlogic: XLP PCIe controller support.
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (9 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 10/14] MIPS: Netlogic: Platform changes for XLR/XLS I2C Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 12/14] MIPS: Netlogic: USB support for XLP Jayachandran C
` (2 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Ganesan Ramalingam, Jayachandran C
From: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Adds support for the XLP on-chip PCIe controller. On XLP, the
on-chip devices(including the 4 PCIe links) appear in the PCIe
configuration space of the XLP as PCI devices.
The changes are to initialize and register the PCIe controller,
enable hardware byte swap in the PCIe IO and MEM space, and to
enable PCIe interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/Kconfig | 1 -
arch/mips/include/asm/netlogic/xlp-hal/iomap.h | 3 +
arch/mips/include/asm/netlogic/xlp-hal/pcibus.h | 76 +++++++
arch/mips/include/asm/netlogic/xlp-hal/xlp.h | 8 +-
arch/mips/netlogic/xlp/nlm_hal.c | 16 ++
arch/mips/pci/Makefile | 1 +
arch/mips/pci/pci-xlp.c | 247 +++++++++++++++++++++++
7 files changed, 349 insertions(+), 3 deletions(-)
create mode 100644 arch/mips/include/asm/netlogic/xlp-hal/pcibus.h
create mode 100644 arch/mips/pci/pci-xlp.c
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index b3811dd..db465fb 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -794,7 +794,6 @@ config NLM_XLP_BOARD
select SYS_HAS_CPU_XLP
select SYS_SUPPORTS_SMP
select HW_HAS_PCI
- select SWAP_IO_SPACE
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select 64BIT_PHYS_ADDR
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/iomap.h b/arch/mips/include/asm/netlogic/xlp-hal/iomap.h
index 86cc339..ece86f1 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/iomap.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/iomap.h
@@ -36,6 +36,9 @@
#define __NLM_HAL_IOMAP_H__
#define XLP_DEFAULT_IO_BASE 0x18000000
+#define XLP_DEFAULT_PCI_ECFG_BASE XLP_DEFAULT_IO_BASE
+#define XLP_DEFAULT_PCI_CFG_BASE 0x1c000000
+
#define NMI_BASE 0xbfc00000
#define XLP_IO_CLK 133333333
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/pcibus.h b/arch/mips/include/asm/netlogic/xlp-hal/pcibus.h
new file mode 100644
index 0000000..66c323d
--- /dev/null
+++ b/arch/mips/include/asm/netlogic/xlp-hal/pcibus.h
@@ -0,0 +1,76 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef __NLM_HAL_PCIBUS_H__
+#define __NLM_HAL_PCIBUS_H__
+
+/* PCIE Memory and IO regions */
+#define PCIE_MEM_BASE 0xd0000000ULL
+#define PCIE_MEM_LIMIT 0xdfffffffULL
+#define PCIE_IO_BASE 0x14000000ULL
+#define PCIE_IO_LIMIT 0x15ffffffULL
+
+#define PCIE_BRIDGE_CMD 0x1
+#define PCIE_BRIDGE_MSI_CAP 0x14
+#define PCIE_BRIDGE_MSI_ADDRL 0x15
+#define PCIE_BRIDGE_MSI_ADDRH 0x16
+#define PCIE_BRIDGE_MSI_DATA 0x17
+
+/* XLP Global PCIE configuration space registers */
+#define PCIE_BYTE_SWAP_MEM_BASE 0x247
+#define PCIE_BYTE_SWAP_MEM_LIM 0x248
+#define PCIE_BYTE_SWAP_IO_BASE 0x249
+#define PCIE_BYTE_SWAP_IO_LIM 0x24A
+#define PCIE_MSI_STATUS 0x25A
+#define PCIE_MSI_EN 0x25B
+#define PCIE_INT_EN0 0x261
+
+/* PCIE_MSI_EN */
+#define PCIE_MSI_VECTOR_INT_EN 0xFFFFFFFF
+
+/* PCIE_INT_EN0 */
+#define PCIE_MSI_INT_EN (1 << 9)
+
+#ifndef __ASSEMBLY__
+
+#define nlm_read_pcie_reg(b, r) nlm_read_reg(b, r)
+#define nlm_write_pcie_reg(b, r, v) nlm_write_reg(b, r, v)
+#define nlm_get_pcie_base(node, inst) \
+ nlm_pcicfg_base(XLP_IO_PCIE_OFFSET(node, inst))
+#define nlm_get_pcie_regbase(node, inst) \
+ (nlm_get_pcie_base(node, inst) + XLP_IO_PCI_HDRSZ)
+
+int xlp_pcie_link_irt(int link);
+#endif
+#endif /* __NLM_HAL_PCIBUS_H__ */
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/xlp.h b/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
index 1540588..dc6e98e 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
@@ -35,8 +35,12 @@
#ifndef _NLM_HAL_XLP_H
#define _NLM_HAL_XLP_H
-#define PIC_UART_0_IRQ 17
-#define PIC_UART_1_IRQ 18
+#define PIC_UART_0_IRQ 17
+#define PIC_UART_1_IRQ 18
+#define PIC_PCIE_LINK_0_IRQ 19
+#define PIC_PCIE_LINK_1_IRQ 20
+#define PIC_PCIE_LINK_2_IRQ 21
+#define PIC_PCIE_LINK_3_IRQ 22
#ifndef __ASSEMBLY__
diff --git a/arch/mips/netlogic/xlp/nlm_hal.c b/arch/mips/netlogic/xlp/nlm_hal.c
index 9428e71..3a4a172 100644
--- a/arch/mips/netlogic/xlp/nlm_hal.c
+++ b/arch/mips/netlogic/xlp/nlm_hal.c
@@ -69,6 +69,14 @@ int nlm_irq_to_irt(int irq)
return PIC_IRT_UART_0_INDEX;
case PIC_UART_1_IRQ:
return PIC_IRT_UART_1_INDEX;
+ case PIC_PCIE_LINK_0_IRQ:
+ return PIC_IRT_PCIE_LINK_0_INDEX;
+ case PIC_PCIE_LINK_1_IRQ:
+ return PIC_IRT_PCIE_LINK_1_INDEX;
+ case PIC_PCIE_LINK_2_IRQ:
+ return PIC_IRT_PCIE_LINK_2_INDEX;
+ case PIC_PCIE_LINK_3_IRQ:
+ return PIC_IRT_PCIE_LINK_3_INDEX;
default:
return -1;
}
@@ -81,6 +89,14 @@ int nlm_irt_to_irq(int irt)
return PIC_UART_0_IRQ;
case PIC_IRT_UART_1_INDEX:
return PIC_UART_1_IRQ;
+ case PIC_IRT_PCIE_LINK_0_INDEX:
+ return PIC_PCIE_LINK_0_IRQ;
+ case PIC_IRT_PCIE_LINK_1_INDEX:
+ return PIC_PCIE_LINK_1_IRQ;
+ case PIC_IRT_PCIE_LINK_2_INDEX:
+ return PIC_PCIE_LINK_2_IRQ;
+ case PIC_IRT_PCIE_LINK_3_INDEX:
+ return PIC_PCIE_LINK_3_IRQ;
default:
return -1;
}
diff --git a/arch/mips/pci/Makefile b/arch/mips/pci/Makefile
index c3ac4b0..44cdf55 100644
--- a/arch/mips/pci/Makefile
+++ b/arch/mips/pci/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
obj-$(CONFIG_MIKROTIK_RB532) += pci-rc32434.o ops-rc32434.o fixup-rc32434.o
obj-$(CONFIG_CPU_CAVIUM_OCTEON) += pci-octeon.o pcie-octeon.o
obj-$(CONFIG_CPU_XLR) += pci-xlr.o
+obj-$(CONFIG_CPU_XLP) += pci-xlp.o
ifdef CONFIG_PCI_MSI
obj-$(CONFIG_CPU_CAVIUM_OCTEON) += msi-octeon.o
diff --git a/arch/mips/pci/pci-xlp.c b/arch/mips/pci/pci-xlp.c
new file mode 100644
index 0000000..3e177e9
--- /dev/null
+++ b/arch/mips/pci/pci-xlp.c
@@ -0,0 +1,247 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/msi.h>
+#include <linux/mm.h>
+#include <linux/irq.h>
+#include <linux/irqdesc.h>
+#include <linux/console.h>
+
+#include <asm/io.h>
+
+#include <asm/netlogic/interrupt.h>
+#include <asm/netlogic/haldefs.h>
+
+#include <asm/netlogic/xlp-hal/iomap.h>
+#include <asm/netlogic/xlp-hal/pic.h>
+#include <asm/netlogic/xlp-hal/xlp.h>
+#include <asm/netlogic/xlp-hal/pcibus.h>
+#include <asm/netlogic/xlp-hal/bridge.h>
+
+static void *pci_config_base;
+
+#define pci_cfg_addr(bus, devfn, off) (((bus) << 20) | ((devfn) << 12) | (off))
+
+/* PCI ops */
+static inline u32 pci_cfg_read_32bit(struct pci_bus *bus, unsigned int devfn,
+ int where)
+{
+ u32 data;
+ u32 *cfgaddr;
+
+ cfgaddr = (u32 *)(pci_config_base +
+ pci_cfg_addr(bus->number, devfn, where & ~3));
+ data = *cfgaddr;
+ return data;
+}
+
+static inline void pci_cfg_write_32bit(struct pci_bus *bus, unsigned int devfn,
+ int where, u32 data)
+{
+ u32 *cfgaddr;
+
+ cfgaddr = (u32 *)(pci_config_base +
+ pci_cfg_addr(bus->number, devfn, where & ~3));
+ *cfgaddr = data;
+}
+
+static int nlm_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ u32 data;
+
+ if ((size == 2) && (where & 1))
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+ else if ((size == 4) && (where & 3))
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+
+ data = pci_cfg_read_32bit(bus, devfn, where);
+
+ if (size == 1)
+ *val = (data >> ((where & 3) << 3)) & 0xff;
+ else if (size == 2)
+ *val = (data >> ((where & 3) << 3)) & 0xffff;
+ else
+ *val = data;
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+
+static int nlm_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ u32 data;
+
+ if ((size == 2) && (where & 1))
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+ else if ((size == 4) && (where & 3))
+ return PCIBIOS_BAD_REGISTER_NUMBER;
+
+ data = pci_cfg_read_32bit(bus, devfn, where);
+
+ if (size == 1)
+ data = (data & ~(0xff << ((where & 3) << 3))) |
+ (val << ((where & 3) << 3));
+ else if (size == 2)
+ data = (data & ~(0xffff << ((where & 3) << 3))) |
+ (val << ((where & 3) << 3));
+ else
+ data = val;
+
+ pci_cfg_write_32bit(bus, devfn, where, data);
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops nlm_pci_ops = {
+ .read = nlm_pcibios_read,
+ .write = nlm_pcibios_write
+};
+
+static struct resource nlm_pci_mem_resource = {
+ .name = "XLP PCI MEM",
+ .start = 0xd0000000UL, /* 256MB PCI mem @ 0xd000_0000 */
+ .end = 0xdfffffffUL,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct resource nlm_pci_io_resource = {
+ .name = "XLP IO MEM",
+ .start = 0x14000000UL, /* 64MB PCI IO @ 0x1000_0000 */
+ .end = 0x17ffffffUL,
+ .flags = IORESOURCE_IO,
+};
+
+struct pci_controller nlm_pci_controller = {
+ .index = 0,
+ .pci_ops = &nlm_pci_ops,
+ .mem_resource = &nlm_pci_mem_resource,
+ .mem_offset = 0x00000000UL,
+ .io_resource = &nlm_pci_io_resource,
+ .io_offset = 0x00000000UL,
+};
+
+static int get_irq_vector(const struct pci_dev *dev)
+{
+ /*
+ * For XLP PCIe, there is an IRQ per Link, find out which
+ * link the device is on to assign interrupts
+ */
+ if (dev->bus->self == NULL)
+ return 0;
+
+ switch (dev->bus->self->devfn) {
+ case 0x8:
+ return PIC_PCIE_LINK_0_IRQ;
+ case 0x9:
+ return PIC_PCIE_LINK_1_IRQ;
+ case 0xa:
+ return PIC_PCIE_LINK_2_IRQ;
+ case 0xb:
+ return PIC_PCIE_LINK_3_IRQ;
+ }
+ WARN(1, "Unexpected devfn %d\n", dev->bus->self->devfn);
+ return 0;
+}
+
+int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+ return get_irq_vector(dev);
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+ return 0;
+}
+
+static int xlp_enable_pci_bswap(void)
+{
+ uint64_t pciebase, sysbase;
+ int node, i;
+ u32 reg;
+
+ /* Chip-0 so node set to 0 */
+ node = 0;
+ sysbase = nlm_get_bridge_regbase(node);
+ /*
+ * Enable byte swap in hardware. Program each link's PCIe SWAP regions
+ * from the link's address ranges.
+ */
+ for (i = 0; i < 4; i++) {
+ pciebase = nlm_pcicfg_base(XLP_IO_PCIE_OFFSET(node, i));
+ if (nlm_read_pci_reg(pciebase, 0) == 0xffffffff)
+ continue;
+
+ reg = nlm_read_bridge_reg(sysbase, BRIDGE_PCIEMEM_BASE0 + i);
+ nlm_write_pci_reg(pciebase, PCIE_BYTE_SWAP_MEM_BASE, reg);
+
+ reg = nlm_read_bridge_reg(sysbase, BRIDGE_PCIEMEM_LIMIT0 + i);
+ nlm_write_pci_reg(pciebase, PCIE_BYTE_SWAP_MEM_LIM, reg);
+
+ reg = nlm_read_bridge_reg(sysbase, BRIDGE_PCIEIO_BASE0 + i);
+ nlm_write_pci_reg(pciebase, PCIE_BYTE_SWAP_IO_BASE, reg);
+
+ reg = nlm_read_bridge_reg(sysbase, BRIDGE_PCIEIO_LIMIT0 + i);
+ nlm_write_pci_reg(pciebase, PCIE_BYTE_SWAP_IO_LIM, reg);
+ }
+ return 0;
+}
+
+static int __init pcibios_init(void)
+{
+ /* Firmware assigns PCI resources */
+ pci_set_flags(PCI_PROBE_ONLY);
+ pci_config_base = ioremap(XLP_DEFAULT_PCI_ECFG_BASE, 64 << 20);
+
+ /* Extend IO port for memory mapped io */
+ ioport_resource.start = 0;
+ ioport_resource.end = ~0;
+
+ xlp_enable_pci_bswap();
+ set_io_port_base(CKSEG1);
+ nlm_pci_controller.io_map_base = CKSEG1;
+
+ register_pci_controller(&nlm_pci_controller);
+ pr_info("XLP PCIe Controller %pR%pR.\n", &nlm_pci_io_resource,
+ &nlm_pci_mem_resource);
+
+ return 0;
+}
+arch_initcall(pcibios_init);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 12/14] MIPS: Netlogic: USB support for XLP
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (10 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 11/14] MIPS: Netlogic: XLP PCIe controller support Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 13/14] MIPS: Netlogic: Add IRQ mappings for more devices Jayachandran C
2012-05-08 12:42 ` [PATCH 14/14] MIPS: Netlogic: Add XLP SoC devices in FDT Jayachandran C
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Ganesan Ramalingam, Jayachandran C
From: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
The XLP USB controller appears as a device on the internal SoC PCIe
bus, the block has 2 EHCI blocks and 4 OHCI blocks. Change are to:
* Add files netlogic/xlp/usb-init.c and asm/netlogic/xlp-hal/usb.h
to initialize the USB controller and define PCI fixups. The PCI
fixups are to setup interrupts and DMA mask.
* Update include/asm/xlp-hal/{iomap.h,pic.h,xlp.h} to add interrupt
mapping for EHCI/OHCI interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/include/asm/netlogic/xlp-hal/iomap.h | 2 +-
arch/mips/include/asm/netlogic/xlp-hal/pic.h | 4 +
arch/mips/include/asm/netlogic/xlp-hal/usb.h | 64 ++++++++++++
arch/mips/include/asm/netlogic/xlp-hal/xlp.h | 6 ++
arch/mips/netlogic/xlp/Makefile | 1 +
arch/mips/netlogic/xlp/nlm_hal.c | 24 +++++
arch/mips/netlogic/xlp/platform.c | 2 +-
arch/mips/netlogic/xlp/usb-init.c | 124 ++++++++++++++++++++++++
8 files changed, 225 insertions(+), 2 deletions(-)
create mode 100644 arch/mips/include/asm/netlogic/xlp-hal/usb.h
create mode 100644 arch/mips/netlogic/xlp/usb-init.c
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/iomap.h b/arch/mips/include/asm/netlogic/xlp-hal/iomap.h
index ece86f1..2c63f97 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/iomap.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/iomap.h
@@ -132,7 +132,7 @@
#define PCI_DEVICE_ID_NLM_PIC 0x1003
#define PCI_DEVICE_ID_NLM_PCIE 0x1004
#define PCI_DEVICE_ID_NLM_EHCI 0x1007
-#define PCI_DEVICE_ID_NLM_ILK 0x1008
+#define PCI_DEVICE_ID_NLM_OHCI 0x1008
#define PCI_DEVICE_ID_NLM_NAE 0x1009
#define PCI_DEVICE_ID_NLM_POE 0x100A
#define PCI_DEVICE_ID_NLM_FMN 0x100B
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/pic.h b/arch/mips/include/asm/netlogic/xlp-hal/pic.h
index b6628f7..ad8b802 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/pic.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/pic.h
@@ -201,7 +201,11 @@
#define PIC_NUM_USB_IRTS 6
#define PIC_IRT_USB_0_INDEX 115
#define PIC_IRT_EHCI_0_INDEX 115
+#define PIC_IRT_OHCI_0_INDEX 116
+#define PIC_IRT_OHCI_1_INDEX 117
#define PIC_IRT_EHCI_1_INDEX 118
+#define PIC_IRT_OHCI_2_INDEX 119
+#define PIC_IRT_OHCI_3_INDEX 120
#define PIC_IRT_USB_INDEX(num) ((num) + PIC_IRT_USB_0_INDEX)
/* 115 to 120 */
#define PIC_IRT_GDX_INDEX 121
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/usb.h b/arch/mips/include/asm/netlogic/xlp-hal/usb.h
new file mode 100644
index 0000000..a9cd350
--- /dev/null
+++ b/arch/mips/include/asm/netlogic/xlp-hal/usb.h
@@ -0,0 +1,64 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef __NLM_HAL_USB_H__
+#define __NLM_HAL_USB_H__
+
+#define USB_CTL_0 0x01
+#define USB_PHY_0 0x0A
+#define USB_PHY_RESET 0x01
+#define USB_PHY_PORT_RESET_0 0x10
+#define USB_PHY_PORT_RESET_1 0x20
+#define USB_CONTROLLER_RESET 0x01
+#define USB_INT_STATUS 0x0E
+#define USB_INT_EN 0x0F
+#define USB_PHY_INTERRUPT_EN 0x01
+#define USB_OHCI_INTERRUPT_EN 0x02
+#define USB_OHCI_INTERRUPT1_EN 0x04
+#define USB_OHCI_INTERRUPT2_EN 0x08
+#define USB_CTRL_INTERRUPT_EN 0x10
+
+#ifndef __ASSEMBLY__
+
+#define nlm_read_usb_reg(b, r) nlm_read_reg(b, r)
+#define nlm_write_usb_reg(b, r, v) nlm_write_reg(b, r, v)
+#define nlm_get_usb_pcibase(node, inst) \
+ nlm_pcicfg_base(XLP_IO_USB_OFFSET(node, inst))
+#define nlm_get_usb_hcd_base(node, inst) \
+ nlm_xkphys_map_pcibar0(nlm_get_usb_pcibase(node, inst))
+#define nlm_get_usb_regbase(node, inst) \
+ (nlm_get_usb_pcibase(node, inst) + XLP_IO_PCI_HDRSZ)
+
+#endif
+#endif /* __NLM_HAL_USB_H__ */
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/xlp.h b/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
index dc6e98e..3921a31 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
@@ -41,6 +41,12 @@
#define PIC_PCIE_LINK_1_IRQ 20
#define PIC_PCIE_LINK_2_IRQ 21
#define PIC_PCIE_LINK_3_IRQ 22
+#define PIC_EHCI_0_IRQ 23
+#define PIC_EHCI_1_IRQ 24
+#define PIC_OHCI_0_IRQ 25
+#define PIC_OHCI_1_IRQ 26
+#define PIC_OHCI_2_IRQ 27
+#define PIC_OHCI_3_IRQ 28
#ifndef __ASSEMBLY__
diff --git a/arch/mips/netlogic/xlp/Makefile b/arch/mips/netlogic/xlp/Makefile
index b93ed83..5bd24b6 100644
--- a/arch/mips/netlogic/xlp/Makefile
+++ b/arch/mips/netlogic/xlp/Makefile
@@ -1,2 +1,3 @@
obj-y += setup.o platform.o nlm_hal.o
obj-$(CONFIG_SMP) += wakeup.o
+obj-$(CONFIG_USB) += usb-init.o
diff --git a/arch/mips/netlogic/xlp/nlm_hal.c b/arch/mips/netlogic/xlp/nlm_hal.c
index 3a4a172..fad2cae 100644
--- a/arch/mips/netlogic/xlp/nlm_hal.c
+++ b/arch/mips/netlogic/xlp/nlm_hal.c
@@ -77,6 +77,18 @@ int nlm_irq_to_irt(int irq)
return PIC_IRT_PCIE_LINK_2_INDEX;
case PIC_PCIE_LINK_3_IRQ:
return PIC_IRT_PCIE_LINK_3_INDEX;
+ case PIC_EHCI_0_IRQ:
+ return PIC_IRT_EHCI_0_INDEX;
+ case PIC_EHCI_1_IRQ:
+ return PIC_IRT_EHCI_1_INDEX;
+ case PIC_OHCI_0_IRQ:
+ return PIC_IRT_OHCI_0_INDEX;
+ case PIC_OHCI_1_IRQ:
+ return PIC_IRT_OHCI_1_INDEX;
+ case PIC_OHCI_2_IRQ:
+ return PIC_IRT_OHCI_2_INDEX;
+ case PIC_OHCI_3_IRQ:
+ return PIC_IRT_OHCI_3_INDEX;
default:
return -1;
}
@@ -97,6 +109,18 @@ int nlm_irt_to_irq(int irt)
return PIC_PCIE_LINK_2_IRQ;
case PIC_IRT_PCIE_LINK_3_INDEX:
return PIC_PCIE_LINK_3_IRQ;
+ case PIC_IRT_EHCI_0_INDEX:
+ return PIC_EHCI_0_IRQ;
+ case PIC_IRT_EHCI_1_INDEX:
+ return PIC_EHCI_1_IRQ;
+ case PIC_IRT_OHCI_0_INDEX:
+ return PIC_OHCI_0_IRQ;
+ case PIC_IRT_OHCI_1_INDEX:
+ return PIC_OHCI_1_IRQ;
+ case PIC_IRT_OHCI_2_INDEX:
+ return PIC_OHCI_2_IRQ;
+ case PIC_IRT_OHCI_3_INDEX:
+ return PIC_OHCI_3_IRQ;
default:
return -1;
}
diff --git a/arch/mips/netlogic/xlp/platform.c b/arch/mips/netlogic/xlp/platform.c
index 1f5e4cb..2c510d5 100644
--- a/arch/mips/netlogic/xlp/platform.c
+++ b/arch/mips/netlogic/xlp/platform.c
@@ -53,7 +53,7 @@
static unsigned int nlm_xlp_uart_in(struct uart_port *p, int offset)
{
- return nlm_read_reg(p->iobase, offset);
+ return nlm_read_reg(p->iobase, offset);
}
static void nlm_xlp_uart_out(struct uart_port *p, int offset, int value)
diff --git a/arch/mips/netlogic/xlp/usb-init.c b/arch/mips/netlogic/xlp/usb-init.c
new file mode 100644
index 0000000..dbe083a
--- /dev/null
+++ b/arch/mips/netlogic/xlp/usb-init.c
@@ -0,0 +1,124 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+
+#include <asm/netlogic/haldefs.h>
+#include <asm/netlogic/xlp-hal/iomap.h>
+#include <asm/netlogic/xlp-hal/xlp.h>
+#include <asm/netlogic/xlp-hal/usb.h>
+
+static void nlm_usb_intr_en(int node, int port)
+{
+ uint32_t val;
+ uint64_t port_addr;
+
+ port_addr = nlm_get_usb_regbase(node, port);
+ val = nlm_read_usb_reg(port_addr, USB_INT_EN);
+ val = USB_CTRL_INTERRUPT_EN | USB_OHCI_INTERRUPT_EN |
+ USB_OHCI_INTERRUPT1_EN | USB_CTRL_INTERRUPT_EN |
+ USB_OHCI_INTERRUPT_EN | USB_OHCI_INTERRUPT2_EN;
+ nlm_write_usb_reg(port_addr, USB_INT_EN, val);
+}
+
+static void nlm_usb_hw_reset(int node, int port)
+{
+ uint64_t port_addr;
+ uint32_t val;
+
+ /* reset USB phy */
+ port_addr = nlm_get_usb_regbase(node, port);
+ val = nlm_read_usb_reg(port_addr, USB_PHY_0);
+ val &= ~(USB_PHY_RESET | USB_PHY_PORT_RESET_0 | USB_PHY_PORT_RESET_1);
+ nlm_write_usb_reg(port_addr, USB_PHY_0, val);
+
+ mdelay(100);
+ val = nlm_read_usb_reg(port_addr, USB_CTL_0);
+ val &= ~(USB_CONTROLLER_RESET);
+ val |= 0x4;
+ nlm_write_usb_reg(port_addr, USB_CTL_0, val);
+}
+
+static int __init nlm_platform_usb_init(void)
+{
+ pr_info("Initializing USB Interface\n");
+ nlm_usb_hw_reset(0, 0);
+ nlm_usb_hw_reset(0, 3);
+
+ /* Enable PHY interrupts */
+ nlm_usb_intr_en(0, 0);
+ nlm_usb_intr_en(0, 3);
+
+ return 0;
+}
+
+arch_initcall(nlm_platform_usb_init);
+
+static u64 xlp_usb_dmamask = ~(u32)0;
+
+/* Fixup the IRQ for USB devices which is exist on XLP SOC PCIE bus */
+static void nlm_usb_fixup_final(struct pci_dev *dev)
+{
+ dev->dev.dma_mask = &xlp_usb_dmamask;
+ dev->dev.coherent_dma_mask = DMA_BIT_MASK(64);
+ switch (dev->devfn) {
+ case 0x10:
+ dev->irq = PIC_EHCI_0_IRQ;
+ break;
+ case 0x11:
+ dev->irq = PIC_OHCI_0_IRQ;
+ break;
+ case 0x12:
+ dev->irq = PIC_OHCI_1_IRQ;
+ break;
+ case 0x13:
+ dev->irq = PIC_EHCI_1_IRQ;
+ break;
+ case 0x14:
+ dev->irq = PIC_OHCI_2_IRQ;
+ break;
+ case 0x15:
+ dev->irq = PIC_OHCI_3_IRQ;
+ break;
+ }
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_EHCI,
+ nlm_usb_fixup_final);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_OHCI,
+ nlm_usb_fixup_final);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 13/14] MIPS: Netlogic: Add IRQ mappings for more devices
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (11 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 12/14] MIPS: Netlogic: USB support for XLP Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
2012-05-08 12:42 ` [PATCH 14/14] MIPS: Netlogic: Add XLP SoC devices in FDT Jayachandran C
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Jayachandran C
Add IRT to IRQ translation for the MMC and I2C IRQs.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/include/asm/netlogic/xlp-hal/xlp.h | 3 +++
arch/mips/netlogic/xlp/nlm_hal.c | 12 ++++++++++++
2 files changed, 15 insertions(+)
diff --git a/arch/mips/include/asm/netlogic/xlp-hal/xlp.h b/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
index 3921a31..7e47209 100644
--- a/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
+++ b/arch/mips/include/asm/netlogic/xlp-hal/xlp.h
@@ -47,6 +47,9 @@
#define PIC_OHCI_1_IRQ 26
#define PIC_OHCI_2_IRQ 27
#define PIC_OHCI_3_IRQ 28
+#define PIC_MMC_IRQ 29
+#define PIC_I2C_0_IRQ 30
+#define PIC_I2C_1_IRQ 31
#ifndef __ASSEMBLY__
diff --git a/arch/mips/netlogic/xlp/nlm_hal.c b/arch/mips/netlogic/xlp/nlm_hal.c
index fad2cae..6c65ac7 100644
--- a/arch/mips/netlogic/xlp/nlm_hal.c
+++ b/arch/mips/netlogic/xlp/nlm_hal.c
@@ -89,6 +89,12 @@ int nlm_irq_to_irt(int irq)
return PIC_IRT_OHCI_2_INDEX;
case PIC_OHCI_3_IRQ:
return PIC_IRT_OHCI_3_INDEX;
+ case PIC_MMC_IRQ:
+ return PIC_IRT_MMC_INDEX;
+ case PIC_I2C_0_IRQ:
+ return PIC_IRT_I2C_0_INDEX;
+ case PIC_I2C_1_IRQ:
+ return PIC_IRT_I2C_1_INDEX;
default:
return -1;
}
@@ -121,6 +127,12 @@ int nlm_irt_to_irq(int irt)
return PIC_OHCI_2_IRQ;
case PIC_IRT_OHCI_3_INDEX:
return PIC_OHCI_3_IRQ;
+ case PIC_IRT_MMC_INDEX:
+ return PIC_MMC_IRQ;
+ case PIC_IRT_I2C_0_INDEX:
+ return PIC_I2C_0_IRQ;
+ case PIC_IRT_I2C_1_INDEX:
+ return PIC_I2C_1_IRQ;
default:
return -1;
}
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 14/14] MIPS: Netlogic: Add XLP SoC devices in FDT
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
` (12 preceding siblings ...)
2012-05-08 12:42 ` [PATCH 13/14] MIPS: Netlogic: Add IRQ mappings for more devices Jayachandran C
@ 2012-05-08 12:42 ` Jayachandran C
13 siblings, 0 replies; 15+ messages in thread
From: Jayachandran C @ 2012-05-08 12:42 UTC (permalink / raw)
To: linux-mips, ralf; +Cc: Ganesan Ramalingam, Jayachandran C
From: Ganesan Ramalingam <ganesanr@broadcom.com>
Probe and add devices on SoC "simple-bus" on startup. This will
in turn add devices like I2C controller that are specified in the
device tree under 'soc'.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
---
arch/mips/netlogic/xlp/setup.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/mips/netlogic/xlp/setup.c b/arch/mips/netlogic/xlp/setup.c
index b3df7c2..3dec9f2 100644
--- a/arch/mips/netlogic/xlp/setup.c
+++ b/arch/mips/netlogic/xlp/setup.c
@@ -41,6 +41,8 @@
#include <asm/bootinfo.h>
#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+#include <linux/of_device.h>
#include <asm/netlogic/haldefs.h>
#include <asm/netlogic/common.h>
@@ -109,3 +111,17 @@ void __init prom_init(void)
register_smp_ops(&nlm_smp_ops);
#endif
}
+
+static struct of_device_id __initdata xlp_ids[] = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+int __init xlp8xx_ds_publish_devices(void)
+{
+ if (!of_have_populated_dt())
+ return 0;
+ return of_platform_bus_probe(NULL, xlp_ids, NULL);
+}
+
+device_initcall(xlp8xx_ds_publish_devices);
--
1.7.9.5
^ permalink raw reply related [flat|nested] 15+ messages in thread
end of thread, other threads:[~2012-05-08 12:48 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-05-08 12:41 [PATCH UPDATED 00/14] Netlogic XLR/XLS/XLP updates Jayachandran C
2012-05-08 12:41 ` [PATCH 01/14] MIPS: Netlogic: Fix PCIX irq on XLR chips Jayachandran C
2012-05-08 12:41 ` [PATCH 02/14] MIPS: Netlogic: MSI enable fix for XLS Jayachandran C
2012-05-08 12:41 ` [PATCH 03/14] MIPS: Netlogic: Remove unused pcibios_fixups Jayachandran C
2012-05-08 12:41 ` [PATCH 04/14] MIPS: Netlogic: Fix TLB size of boot CPU Jayachandran C
2012-05-08 12:41 ` [PATCH 05/14] MIPS: Netlogic: Update comments in smpboot.S Jayachandran C
2012-05-08 12:42 ` [PATCH 06/14] MIPS: Netlogic: SMP wakeup code update Jayachandran C
2012-05-08 12:42 ` [PATCH 07/14] MIPS: Netlogic: Remove NETLOGIC_ prefix Jayachandran C
2012-05-08 12:42 ` [PATCH 08/14] MIPS: Netlogic: Platform changes for XLS USB Jayachandran C
2012-05-08 12:42 ` [PATCH 09/14] MIPS: Netlogic: Platform NAND/NOR flash support Jayachandran C
2012-05-08 12:42 ` [PATCH 10/14] MIPS: Netlogic: Platform changes for XLR/XLS I2C Jayachandran C
2012-05-08 12:42 ` [PATCH 11/14] MIPS: Netlogic: XLP PCIe controller support Jayachandran C
2012-05-08 12:42 ` [PATCH 12/14] MIPS: Netlogic: USB support for XLP Jayachandran C
2012-05-08 12:42 ` [PATCH 13/14] MIPS: Netlogic: Add IRQ mappings for more devices Jayachandran C
2012-05-08 12:42 ` [PATCH 14/14] MIPS: Netlogic: Add XLP SoC devices in FDT Jayachandran C
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.