* [PATCH] bq27x00_battery: Add support for BQ27425 chip
@ 2012-06-18 6:10 Saranya Gopal
2012-06-18 9:06 ` Lars-Peter Clausen
0 siblings, 1 reply; 2+ messages in thread
From: Saranya Gopal @ 2012-06-18 6:10 UTC (permalink / raw)
To: cbou, dwmw2; +Cc: linux-kernel, Saranya Gopal
This patch adds support for BQ27425 (TI) chip. This
chip is same as BQ27500 with few registers removed
and register address map changed. The data sheet for
this chip is publicly available at
http://www.ti.com/product/bq27425-g1
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
---
drivers/power/Kconfig | 7 +++
drivers/power/bq27x00_battery.c | 85 +++++++++++++++++++++++++++++---------
2 files changed, 72 insertions(+), 20 deletions(-)
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index e3a3b49..38f6807 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -157,6 +157,13 @@ config BATTERY_BQ27X00_PLATFORM
help
Say Y here to enable support for batteries with BQ27000 (HDQ) chips.
+config BATTERY_BQ27425
+ bool "BQ27425 support"
+ depends on BATTERY_BQ27x00
+ depends on BATTERY_BQ27X00_I2C
+ help
+ Say Y here to enable support for batteries with BQ27425 (I2C) chip.
+
config BATTERY_DA9030
tristate "DA9030 battery driver"
depends on PMIC_DA903X
diff --git a/drivers/power/bq27x00_battery.c b/drivers/power/bq27x00_battery.c
index f5d6d37..d22e415 100644
--- a/drivers/power/bq27x00_battery.c
+++ b/drivers/power/bq27x00_battery.c
@@ -22,6 +22,7 @@
* Datasheets:
* http://focus.ti.com/docs/prod/folders/print/bq27000.html
* http://focus.ti.com/docs/prod/folders/print/bq27500.html
+ * http://www.ti.com/product/bq27425-g1
*/
#include <linux/module.h>
@@ -67,6 +68,14 @@
#define BQ27500_FLAG_SOC1 BIT(2) /* State-of-Charge threshold 1 */
#define BQ27500_FLAG_FC BIT(9)
+#define BQ27425_REG_TEMP 0x02
+#define BQ27425_REG_VOLT 0x04
+#define BQ27425_REG_FLAGS 0x06
+#define BQ27425_REG_NAC 0x08
+#define BQ27425_REG_FCC 0x0E
+#define BQ27425_REG_AI 0x10
+#define BQ27425_REG_SOC 0x1C
+
#define BQ27000_RS 20 /* Resistor sense */
struct bq27x00_device_info;
@@ -74,7 +83,7 @@ struct bq27x00_access_methods {
int (*read)(struct bq27x00_device_info *di, u8 reg, bool single);
};
-enum bq27x00_chip { BQ27000, BQ27500 };
+enum bq27x00_chip { BQ27000, BQ27500, BQ27425};
struct bq27x00_reg_cache {
int temperature;
@@ -114,15 +123,17 @@ static enum power_supply_property bq27x00_battery_props[] = {
POWER_SUPPLY_PROP_CAPACITY,
POWER_SUPPLY_PROP_CAPACITY_LEVEL,
POWER_SUPPLY_PROP_TEMP,
+#ifndef CONFIG_BATTERY_BQ27425
POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
+ POWER_SUPPLY_PROP_CYCLE_COUNT,
+ POWER_SUPPLY_PROP_ENERGY_NOW,
+#endif
POWER_SUPPLY_PROP_TECHNOLOGY,
POWER_SUPPLY_PROP_CHARGE_FULL,
POWER_SUPPLY_PROP_CHARGE_NOW,
POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
- POWER_SUPPLY_PROP_CYCLE_COUNT,
- POWER_SUPPLY_PROP_ENERGY_NOW,
};
static unsigned int poll_interval = 360;
@@ -150,6 +161,8 @@ static int bq27x00_battery_read_rsoc(struct bq27x00_device_info *di)
if (di->chip == BQ27500)
rsoc = bq27x00_read(di, BQ27500_REG_SOC, false);
+ else if (di->chip == BQ27425)
+ rsoc = bq27x00_read(di, BQ27425_REG_SOC, false);
else
rsoc = bq27x00_read(di, BQ27000_REG_RSOC, true);
@@ -174,7 +187,7 @@ static int bq27x00_battery_read_charge(struct bq27x00_device_info *di, u8 reg)
return charge;
}
- if (di->chip == BQ27500)
+ if (di->chip == BQ27500 || di->chip == BQ27425)
charge *= 1000;
else
charge = charge * 3570 / BQ27000_RS;
@@ -188,6 +201,8 @@ static int bq27x00_battery_read_charge(struct bq27x00_device_info *di, u8 reg)
*/
static inline int bq27x00_battery_read_nac(struct bq27x00_device_info *di)
{
+ if (di->chip == BQ27425)
+ return bq27x00_battery_read_charge(di, BQ27425_REG_NAC);
return bq27x00_battery_read_charge(di, BQ27x00_REG_NAC);
}
@@ -197,6 +212,8 @@ static inline int bq27x00_battery_read_nac(struct bq27x00_device_info *di)
*/
static inline int bq27x00_battery_read_lmd(struct bq27x00_device_info *di)
{
+ if (di->chip == BQ27425)
+ return bq27x00_battery_read_charge(di, BQ27425_REG_FCC);
return bq27x00_battery_read_charge(di, BQ27x00_REG_LMD);
}
@@ -208,7 +225,7 @@ static int bq27x00_battery_read_ilmd(struct bq27x00_device_info *di)
{
int ilmd;
- if (di->chip == BQ27500)
+ if (di->chip == BQ27500 || di->chip == BQ27425)
ilmd = bq27x00_read(di, BQ27500_REG_DCAP, false);
else
ilmd = bq27x00_read(di, BQ27000_REG_ILMD, true);
@@ -218,7 +235,7 @@ static int bq27x00_battery_read_ilmd(struct bq27x00_device_info *di)
return ilmd;
}
- if (di->chip == BQ27500)
+ if (di->chip == BQ27500 || di->chip == BQ27425)
ilmd *= 1000;
else
ilmd = ilmd * 256 * 3570 / BQ27000_RS;
@@ -256,13 +273,16 @@ static int bq27x00_battery_read_temperature(struct bq27x00_device_info *di)
{
int temp;
- temp = bq27x00_read(di, BQ27x00_REG_TEMP, false);
+ if (di->chip == BQ27425)
+ temp = bq27x00_read(di, BQ27425_REG_TEMP, false);
+ else
+ temp = bq27x00_read(di, BQ27x00_REG_TEMP, false);
if (temp < 0) {
dev_err(di->dev, "error reading temperature\n");
return temp;
}
- if (di->chip == BQ27500)
+ if (di->chip == BQ27500 || di->chip == BQ27425)
temp -= 2731;
else
temp = ((temp * 5) - 5463) / 2;
@@ -310,10 +330,15 @@ static void bq27x00_update(struct bq27x00_device_info *di)
{
struct bq27x00_reg_cache cache = {0, };
bool is_bq27500 = di->chip == BQ27500;
+ bool is_bq27425 = di->chip == BQ27425;
- cache.flags = bq27x00_read(di, BQ27x00_REG_FLAGS, !is_bq27500);
+ if (is_bq27425)
+ cache.flags = bq27x00_read(di, BQ27425_REG_FLAGS, !is_bq27425);
+ else
+ cache.flags = bq27x00_read(di, BQ27x00_REG_FLAGS, !is_bq27500);
if (cache.flags >= 0) {
- if (!is_bq27500 && (cache.flags & BQ27000_FLAG_CI)) {
+ if (!is_bq27500 && !is_bq27425
+ && (cache.flags & BQ27000_FLAG_CI)) {
dev_info(di->dev, "battery is not calibrated! ignoring capacity values\n");
cache.capacity = -ENODATA;
cache.energy = -ENODATA;
@@ -323,14 +348,23 @@ static void bq27x00_update(struct bq27x00_device_info *di)
cache.charge_full = -ENODATA;
} else {
cache.capacity = bq27x00_battery_read_rsoc(di);
- cache.energy = bq27x00_battery_read_energy(di);
- cache.time_to_empty = bq27x00_battery_read_time(di, BQ27x00_REG_TTE);
- cache.time_to_empty_avg = bq27x00_battery_read_time(di, BQ27x00_REG_TTECP);
- cache.time_to_full = bq27x00_battery_read_time(di, BQ27x00_REG_TTF);
+ if (!is_bq27425) {
+ cache.energy = bq27x00_battery_read_energy(di);
+ cache.time_to_empty =
+ bq27x00_battery_read_time(di,
+ BQ27x00_REG_TTE);
+ cache.time_to_empty_avg =
+ bq27x00_battery_read_time(di,
+ BQ27x00_REG_TTECP);
+ cache.time_to_full =
+ bq27x00_battery_read_time(di,
+ BQ27x00_REG_TTF);
+ }
cache.charge_full = bq27x00_battery_read_lmd(di);
}
cache.temperature = bq27x00_battery_read_temperature(di);
- cache.cycle_count = bq27x00_battery_read_cyct(di);
+ if (!is_bq27425)
+ cache.cycle_count = bq27x00_battery_read_cyct(di);
/* We only have to read charge design full once */
if (di->charge_design_full <= 0)
@@ -370,13 +404,16 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di,
int curr;
int flags;
- curr = bq27x00_read(di, BQ27x00_REG_AI, false);
+ if (di->chip == BQ27425)
+ curr = bq27x00_read(di, BQ27425_REG_AI, false);
+ else
+ curr = bq27x00_read(di, BQ27x00_REG_AI, false);
if (curr < 0) {
dev_err(di->dev, "error reading current\n");
return curr;
}
- if (di->chip == BQ27500) {
+ if (di->chip == BQ27500 || di->chip == BQ27425) {
/* bq27500 returns signed value */
val->intval = (int)((s16)curr) * 1000;
} else {
@@ -397,7 +434,7 @@ static int bq27x00_battery_status(struct bq27x00_device_info *di,
{
int status;
- if (di->chip == BQ27500) {
+ if (di->chip == BQ27500 || di->chip == BQ27425) {
if (di->cache.flags & BQ27500_FLAG_FC)
status = POWER_SUPPLY_STATUS_FULL;
else if (di->cache.flags & BQ27500_FLAG_DSC)
@@ -425,7 +462,7 @@ static int bq27x00_battery_capacity_level(struct bq27x00_device_info *di,
{
int level;
- if (di->chip == BQ27500) {
+ if (di->chip == BQ27500 || di->chip == BQ27425) {
if (di->cache.flags & BQ27500_FLAG_FC)
level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
else if (di->cache.flags & BQ27500_FLAG_SOC1)
@@ -459,7 +496,10 @@ static int bq27x00_battery_voltage(struct bq27x00_device_info *di,
{
int volt;
- volt = bq27x00_read(di, BQ27x00_REG_VOLT, false);
+ if (di->chip == BQ27425)
+ volt = bq27x00_read(di, BQ27425_REG_VOLT, false);
+ else
+ volt = bq27x00_read(di, BQ27x00_REG_VOLT, false);
if (volt < 0) {
dev_err(di->dev, "error reading voltage\n");
return volt;
@@ -523,6 +563,7 @@ static int bq27x00_battery_get_property(struct power_supply *psy,
case POWER_SUPPLY_PROP_TEMP:
ret = bq27x00_simple_value(di->cache.temperature, val);
break;
+#ifndef CONFIG_BATTERY_BQ27425
case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW:
ret = bq27x00_simple_value(di->cache.time_to_empty, val);
break;
@@ -532,6 +573,7 @@ static int bq27x00_battery_get_property(struct power_supply *psy,
case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW:
ret = bq27x00_simple_value(di->cache.time_to_full, val);
break;
+#endif
case POWER_SUPPLY_PROP_TECHNOLOGY:
val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
break;
@@ -544,12 +586,14 @@ static int bq27x00_battery_get_property(struct power_supply *psy,
case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
ret = bq27x00_simple_value(di->charge_design_full, val);
break;
+#ifndef CONFIG_BATTERY_BQ27425
case POWER_SUPPLY_PROP_CYCLE_COUNT:
ret = bq27x00_simple_value(di->cache.cycle_count, val);
break;
case POWER_SUPPLY_PROP_ENERGY_NOW:
ret = bq27x00_simple_value(di->cache.energy, val);
break;
+#endif
default:
return -EINVAL;
}
@@ -729,6 +773,7 @@ static int bq27x00_battery_remove(struct i2c_client *client)
static const struct i2c_device_id bq27x00_id[] = {
{ "bq27200", BQ27000 }, /* bq27200 is same as bq27000, but with i2c */
{ "bq27500", BQ27500 },
+ { "bq27425", BQ27425 },
{},
};
MODULE_DEVICE_TABLE(i2c, bq27x00_id);
--
1.7.1
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] bq27x00_battery: Add support for BQ27425 chip
2012-06-18 6:10 [PATCH] bq27x00_battery: Add support for BQ27425 chip Saranya Gopal
@ 2012-06-18 9:06 ` Lars-Peter Clausen
0 siblings, 0 replies; 2+ messages in thread
From: Lars-Peter Clausen @ 2012-06-18 9:06 UTC (permalink / raw)
To: Saranya Gopal; +Cc: cbou, dwmw2, linux-kernel
On 06/18/2012 08:10 AM, Saranya Gopal wrote:
> This patch adds support for BQ27425 (TI) chip. This
> chip is same as BQ27500 with few registers removed
> and register address map changed. The data sheet for
> this chip is publicly available at
> http://www.ti.com/product/bq27425-g1
>
> Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
> ---
> drivers/power/Kconfig | 7 +++
> drivers/power/bq27x00_battery.c | 85 +++++++++++++++++++++++++++++---------
> 2 files changed, 72 insertions(+), 20 deletions(-)
>
> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
> index e3a3b49..38f6807 100644
> --- a/drivers/power/Kconfig
> +++ b/drivers/power/Kconfig
> @@ -157,6 +157,13 @@ config BATTERY_BQ27X00_PLATFORM
> help
> Say Y here to enable support for batteries with BQ27000 (HDQ) chips.
>
> +config BATTERY_BQ27425
> + bool "BQ27425 support"
> + depends on BATTERY_BQ27x00
> + depends on BATTERY_BQ27X00_I2C
There shouldn't be a need for an additional Kconfig entry.
> + help
> + Say Y here to enable support for batteries with BQ27425 (I2C) chip.
> +
> config BATTERY_DA9030
> tristate "DA9030 battery driver"
> depends on PMIC_DA903X
> diff --git a/drivers/power/bq27x00_battery.c b/drivers/power/bq27x00_battery.c
> index f5d6d37..d22e415 100644
> --- a/drivers/power/bq27x00_battery.c
> +++ b/drivers/power/bq27x00_battery.c
> @@ -22,6 +22,7 @@
> * Datasheets:
> * http://focus.ti.com/docs/prod/folders/print/bq27000.html
> * http://focus.ti.com/docs/prod/folders/print/bq27500.html
> + * http://www.ti.com/product/bq27425-g1
> */
>
> #include <linux/module.h>
> @@ -67,6 +68,14 @@
> #define BQ27500_FLAG_SOC1 BIT(2) /* State-of-Charge threshold 1 */
> #define BQ27500_FLAG_FC BIT(9)
>
> +#define BQ27425_REG_TEMP 0x02
> +#define BQ27425_REG_VOLT 0x04
> +#define BQ27425_REG_FLAGS 0x06
> +#define BQ27425_REG_NAC 0x08
> +#define BQ27425_REG_FCC 0x0E
> +#define BQ27425_REG_AI 0x10
> +#define BQ27425_REG_SOC 0x1C
> +
> #define BQ27000_RS 20 /* Resistor sense */
>
> struct bq27x00_device_info;
> @@ -74,7 +83,7 @@ struct bq27x00_access_methods {
> int (*read)(struct bq27x00_device_info *di, u8 reg, bool single);
> };
>
> -enum bq27x00_chip { BQ27000, BQ27500 };
> +enum bq27x00_chip { BQ27000, BQ27500, BQ27425};
>
> struct bq27x00_reg_cache {
> int temperature;
> @@ -114,15 +123,17 @@ static enum power_supply_property bq27x00_battery_props[] = {
> POWER_SUPPLY_PROP_CAPACITY,
> POWER_SUPPLY_PROP_CAPACITY_LEVEL,
> POWER_SUPPLY_PROP_TEMP,
> +#ifndef CONFIG_BATTERY_BQ27425
Nope, that won't work. If you have support for the bq27425 built-in you'll
also disable these properties for the other devices supported by this
driver. Add a second power_supply_property array for the bq27425 and assign
the appropriate array at run-time depending on the battery type.
> POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
> POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
> POWER_SUPPLY_PROP_TIME_TO_FULL_NOW,
> + POWER_SUPPLY_PROP_CYCLE_COUNT,
> + POWER_SUPPLY_PROP_ENERGY_NOW,
> +#endif
> POWER_SUPPLY_PROP_TECHNOLOGY,
> POWER_SUPPLY_PROP_CHARGE_FULL,
> POWER_SUPPLY_PROP_CHARGE_NOW,
> POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
> - POWER_SUPPLY_PROP_CYCLE_COUNT,
> - POWER_SUPPLY_PROP_ENERGY_NOW,
> };
>
> static unsigned int poll_interval = 360;
> @@ -150,6 +161,8 @@ static int bq27x00_battery_read_rsoc(struct bq27x00_device_info *di)
>
> if (di->chip == BQ27500)
> rsoc = bq27x00_read(di, BQ27500_REG_SOC, false);
> + else if (di->chip == BQ27425)
> + rsoc = bq27x00_read(di, BQ27425_REG_SOC, false);
> else
> rsoc = bq27x00_read(di, BQ27000_REG_RSOC, true);
>
> @@ -174,7 +187,7 @@ static int bq27x00_battery_read_charge(struct bq27x00_device_info *di, u8 reg)
> return charge;
> }
>
> - if (di->chip == BQ27500)
> + if (di->chip == BQ27500 || di->chip == BQ27425)
> charge *= 1000;
> else
> charge = charge * 3570 / BQ27000_RS;
> @@ -188,6 +201,8 @@ static int bq27x00_battery_read_charge(struct bq27x00_device_info *di, u8 reg)
> */
> static inline int bq27x00_battery_read_nac(struct bq27x00_device_info *di)
> {
> + if (di->chip == BQ27425)
> + return bq27x00_battery_read_charge(di, BQ27425_REG_NAC);
Maybe it makes sense to provide a look-up table to do the register mapping
instead of all these if (BQ27425O) use regA else use regB.
> return bq27x00_battery_read_charge(di, BQ27x00_REG_NAC);
> }
> [...]
> @@ -729,6 +773,7 @@ static int bq27x00_battery_remove(struct i2c_client *client)
> static const struct i2c_device_id bq27x00_id[] = {
> { "bq27200", BQ27000 }, /* bq27200 is same as bq27000, but with i2c */
> { "bq27500", BQ27500 },
> + { "bq27425", BQ27425 },
> {},
> };
> MODULE_DEVICE_TABLE(i2c, bq27x00_id);
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2012-06-18 9:03 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-06-18 6:10 [PATCH] bq27x00_battery: Add support for BQ27425 chip Saranya Gopal
2012-06-18 9:06 ` Lars-Peter Clausen
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.