[PATCH -v6 0/4] PCIe, PM, Add PCIe runtime D3cold support

[PATCH -v6 0/4] PCIe, PM, Add PCIe runtime D3cold support

[Huang Ying]

Changelog:

v6:

- Disable device D3cold during system suspend/hibernate with a new method per Rafeal's comments

v5:

- Disable device D3cold during system suspend/hibernate per Rafael's comments

v4:

- Minors fixes based on comments from Rafael

v3:

- Drop device.power.power_must_be_on, use pci_dev.no_d3cold instead
- Drop device.power.power_off_user, use pci_dev.d3cold_allowed instead
- Use black list instead of white list in pcie port runtime support per request from Bjorn
- Various fixes based on comments from Rafael

v2:

- Refreshed based on comments from Rafael

[PATCH -v6 1/4] ACPI, PM, Specify lowest allowed state for device sleep
[PATCH -v6 2/4] PCIe, PM, Add runtime PM support to PCIe port
[PATCH -v6 3/4] PCI, PM, Do not call pci_set_power_state with PCI_D3cold
[PATCH -v6 4/4] PCIe, PM, Add PCIe runtime D3cold support

Best Regards,
Huang Ying

[PATCH -v6 1/4] ACPI, PM, Specify lowest allowed state for device sleep state

[Huang Ying]

Lower device sleep state can save more power, but has more exit
latency too.  Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.

In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added.  So that the caller can enforce
the constraint via the parameter.

This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: linux-acpi@vger.kernel.org
---
 drivers/acpi/sleep.c       |   24 +++++++++++++++++++-----
 drivers/pci/pci-acpi.c     |    3 ++-
 drivers/pnp/pnpacpi/core.c |    4 ++--
 include/acpi/acpi_bus.h    |    6 +++---
 4 files changed, 26 insertions(+), 11 deletions(-)

--- a/drivers/acpi/sleep.c
+++ b/drivers/acpi/sleep.c
@@ -716,8 +716,9 @@ int acpi_suspend(u32 acpi_state)
  *	@dev: device to examine; its driver model wakeup flags control
  *		whether it should be able to wake up the system
  *	@d_min_p: used to store the upper limit of allowed states range
- *	Return value: preferred power state of the device on success, -ENODEV on
- *		failure (ie. if there's no 'struct acpi_device' for @dev)
+ *	@d_max_in: specify the lowest allowed states
+ *	Return value: preferred power state of the device on success, -ENODEV
+ *	(ie. if there's no 'struct acpi_device' for @dev) or -EINVAL on failure
  *
  *	Find the lowest power (highest number) ACPI device power state that
  *	device @dev can be in while the system is in the sleep state represented
@@ -732,13 +733,15 @@ int acpi_suspend(u32 acpi_state)
  *	via @wake.
  */
 
-int acpi_pm_device_sleep_state(struct device *dev, int *d_min_p)
+int acpi_pm_device_sleep_state(struct device *dev, int *d_min_p, int d_max_in)
 {
 	acpi_handle handle = DEVICE_ACPI_HANDLE(dev);
 	struct acpi_device *adev;
 	char acpi_method[] = "_SxD";
 	unsigned long long d_min, d_max;
 
+	if (d_max_in < ACPI_STATE_D0 || d_max_in > ACPI_STATE_D3)
+		return -EINVAL;
 	if (!handle || ACPI_FAILURE(acpi_bus_get_device(handle, &adev))) {
 		printk(KERN_DEBUG "ACPI handle has no context!\n");
 		return -ENODEV;
@@ -746,8 +749,10 @@ int acpi_pm_device_sleep_state(struct de
 
 	acpi_method[2] = '0' + acpi_target_sleep_state;
 	/*
-	 * If the sleep state is S0, we will return D3, but if the device has
-	 * _S0W, we will use the value from _S0W
+	 * If the sleep state is S0, the lowest limit from ACPI is D3,
+	 * but if the device has _S0W, we will use the value from _S0W
+	 * as the lowest limit from ACPI.  Finally, we will constrain
+	 * the lowest limit with the specified one.
 	 */
 	d_min = ACPI_STATE_D0;
 	d_max = ACPI_STATE_D3;
@@ -791,8 +796,17 @@ int acpi_pm_device_sleep_state(struct de
 		}
 	}
 
+	if (d_max_in < d_min)
+		return -EINVAL;
 	if (d_min_p)
 		*d_min_p = d_min;
+	/* constrain d_max with specified lowest limit (max number) */
+	if (d_max > d_max_in) {
+		for (d_max = d_max_in; d_max > d_min; d_max--) {
+			if (adev->power.states[d_max].flags.valid)
+				break;
+		}
+	}
 	return d_max;
 }
 #endif /* CONFIG_PM */
--- a/drivers/pci/pci-acpi.c
+++ b/drivers/pci/pci-acpi.c
@@ -189,7 +189,8 @@ static pci_power_t acpi_pci_choose_state
 {
 	int acpi_state;
 
-	acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL);
+	acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL,
+						ACPI_STATE_D3);
 	if (acpi_state < 0)
 		return PCI_POWER_ERROR;
 
--- a/drivers/pnp/pnpacpi/core.c
+++ b/drivers/pnp/pnpacpi/core.c
@@ -170,8 +170,8 @@ static int pnpacpi_suspend(struct pnp_de
 	}
 
 	if (acpi_bus_power_manageable(handle)) {
-		int power_state = acpi_pm_device_sleep_state(&dev->dev, NULL);
-
+		int power_state = acpi_pm_device_sleep_state(&dev->dev, NULL,
+							     ACPI_STATE_D3);
 		if (power_state < 0)
 			power_state = (state.event == PM_EVENT_ON) ?
 					ACPI_STATE_D0 : ACPI_STATE_D3;
--- a/include/acpi/acpi_bus.h
+++ b/include/acpi/acpi_bus.h
@@ -414,13 +414,13 @@ int acpi_enable_wakeup_device_power(stru
 int acpi_disable_wakeup_device_power(struct acpi_device *dev);
 
 #ifdef CONFIG_PM
-int acpi_pm_device_sleep_state(struct device *, int *);
+int acpi_pm_device_sleep_state(struct device *, int *, int);
 #else
-static inline int acpi_pm_device_sleep_state(struct device *d, int *p)
+static inline int acpi_pm_device_sleep_state(struct device *d, int *p, int m)
 {
 	if (p)
 		*p = ACPI_STATE_D0;
-	return ACPI_STATE_D3;
+	return (m >= ACPI_STATE_D0 && m <= ACPI_STATE_D3) ? m : ACPI_STATE_D0;
 }
 #endif
 

[PATCH -v6 2/4] PCIe, PM, Add runtime PM support to PCIe port

[Huang Ying]

From: "Yan, Zheng" <zheng.z.yan@intel.com>

This patch adds runtime PM support to PCIe port.  This is needed by
PCIe D3cold support, where PCIe device without ACPI node may be
powered on/off by PCIe port.

Because runtime suspend is broken for some chipsets, a black list is
used to disable runtime PM support for these chipsets.

Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/pci/pci.c              |   10 ++++++++++
 drivers/pci/pcie/portdrv_pci.c |   24 ++++++++++++++++++++++++
 2 files changed, 34 insertions(+)

--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1518,6 +1518,16 @@ static void pci_pme_list_scan(struct wor
 	if (!list_empty(&pci_pme_list)) {
 		list_for_each_entry_safe(pme_dev, n, &pci_pme_list, list) {
 			if (pme_dev->dev->pme_poll) {
+				struct pci_dev *bridge;
+
+				bridge = pme_dev->dev->bus->self;
+				/*
+				 * If bridge is in low power state, the
+				 * configuration space of subordinate devices
+				 * may be not accessible
+				 */
+				if (bridge && bridge->current_state != PCI_D0)
+					continue;
 				pci_pme_wakeup(pme_dev->dev, NULL);
 			} else {
 				list_del(&pme_dev->list);
--- a/drivers/pci/pcie/portdrv_pci.c
+++ b/drivers/pci/pcie/portdrv_pci.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/errno.h>
 #include <linux/pm.h>
+#include <linux/pm_runtime.h>
 #include <linux/init.h>
 #include <linux/pcieport_if.h>
 #include <linux/aer.h>
@@ -99,6 +100,15 @@ static int pcie_port_resume_noirq(struct
 	return 0;
 }
 
+#ifdef CONFIG_PM_RUNTIME
+static int pcie_port_runtime_pm(struct device *dev)
+{
+	return 0;
+}
+#else
+#define pcie_port_runtime_pm	NULL
+#endif
+
 static const struct dev_pm_ops pcie_portdrv_pm_ops = {
 	.suspend	= pcie_port_device_suspend,
 	.resume		= pcie_port_device_resume,
@@ -107,6 +117,8 @@ static const struct dev_pm_ops pcie_port
 	.poweroff	= pcie_port_device_suspend,
 	.restore	= pcie_port_device_resume,
 	.resume_noirq	= pcie_port_resume_noirq,
+	.runtime_suspend = pcie_port_runtime_pm,
+	.runtime_resume = pcie_port_runtime_pm,
 };
 
 #define PCIE_PORTDRV_PM_OPS	(&pcie_portdrv_pm_ops)
@@ -117,6 +129,14 @@ static const struct dev_pm_ops pcie_port
 #endif /* !PM */
 
 /*
+ * PCIe port runtime suspend is broken for some chipsets, so use a
+ * black list to disable runtime PM for these chipsets.
+ */
+static const struct pci_device_id port_runtime_pm_black_list[] = {
+	{ /* end: all zeroes */ }
+};
+
+/*
  * pcie_portdrv_probe - Probe PCI-Express port devices
  * @dev: PCI-Express port device being probed
  *
@@ -144,12 +164,16 @@ static int __devinit pcie_portdrv_probe(
 		return status;
 
 	pci_save_state(dev);
+	if (!pci_match_id(port_runtime_pm_black_list, dev))
+		pm_runtime_put_noidle(&dev->dev);
 
 	return 0;
 }
 
 static void pcie_portdrv_remove(struct pci_dev *dev)
 {
+	if (!pci_match_id(port_runtime_pm_black_list, dev))
+		pm_runtime_get_noresume(&dev->dev);
 	pcie_port_device_remove(dev);
 	pci_disable_device(dev);
 }

[PATCH -v6 3/4] PCI, PM, Do not call pci_set_power_state with PCI_D3cold

[Huang Ying]

PCI subsystem has not been ready for D3cold support yet.  So
PCI_D3cold should not be used as parameter for pci_set_power_state.
This patch is needed for upcoming PCI_D3cold support.

This patch has no functionality change, because pci_set_power_state
will bound the parameter to PCI_D3hot too.

Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
---
 arch/x86/pci/mrst.c       |    2 +-
 drivers/misc/cb710/core.c |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

--- a/arch/x86/pci/mrst.c
+++ b/arch/x86/pci/mrst.c
@@ -264,7 +264,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_IN
 
 static void __devinit mrst_power_off_unused_dev(struct pci_dev *dev)
 {
-	pci_set_power_state(dev, PCI_D3cold);
+	pci_set_power_state(dev, PCI_D3hot);
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0801, mrst_power_off_unused_dev);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0809, mrst_power_off_unused_dev);
--- a/drivers/misc/cb710/core.c
+++ b/drivers/misc/cb710/core.c
@@ -180,7 +180,7 @@ static int cb710_suspend(struct pci_dev
 	pci_save_state(pdev);
 	pci_disable_device(pdev);
 	if (state.event & PM_EVENT_SLEEP)
-		pci_set_power_state(pdev, PCI_D3cold);
+		pci_set_power_state(pdev, PCI_D3hot);
 	return 0;
 }
 

[PATCH -v6 4/4] PCIe, PM, Add PCIe runtime D3cold support

[Huang Ying]

This patch adds runtime D3cold support to PCIe bus.  D3cold is the
deepest power saving state for PCIe devices.  Where the main PCIe link
will be powered off totally, so before the PCIe main link is powered
on again, you can not access the device, even the configuration space,
which is still accessible in D3hot.  Because the main PCIe link is not
available, the PCI PM registers can not be used to put device into/out
of D3cold state, that will be done by platform logic such as ACPI
_PR3.

To support remote wake up in D3cold, aux power is supplied, and a
side-band pin: WAKE# is used to notify remote wake up event, the pin
is usually connected to platform logic such as ACPI GPE.  This is
quite different with other power saving states, where remote wake up
is notified via PME message through the PCIe main link.

Some PCIe devices usually have no direct platform logic (such as these
in plug-in slot), for example, there is usually no ACPI _PR3 for them.
The D3cold support for these devices can be done via the PCIe port
connected to it.  When power on/off the PCIe port, the corresponding
PCIe devices are powered on/off too.  And the remote wake up event
from PCIe device will be notified to the corresponding PCIe port.

The PCI subsystem runtime D3cold support and corresponding ACPI
platform support is implemented in the patch.

This patch only enabled runtime D3cold support for PCI devices.  PCI
devices D3cold support during system suspend/hibernate is not enabled.

For more information about PCIe D3cold and corresponding ACPI support,
please refer to:

- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0

Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
---
 drivers/pci/pci-acpi.c         |   23 ++++++--
 drivers/pci/pci-driver.c       |   10 +++
 drivers/pci/pci-sysfs.c        |   29 ++++++++++
 drivers/pci/pci.c              |  114 +++++++++++++++++++++++++++++++++++++----
 drivers/pci/pci.h              |    1 
 drivers/pci/pcie/portdrv_pci.c |   44 ++++++++++++++-
 include/linux/pci.h            |   16 ++++-
 7 files changed, 215 insertions(+), 22 deletions(-)

--- a/drivers/pci/pci-acpi.c
+++ b/drivers/pci/pci-acpi.c
@@ -48,6 +48,12 @@ static void pci_acpi_wake_dev(acpi_handl
 	if (event != ACPI_NOTIFY_DEVICE_WAKE || !pci_dev)
 		return;
 
+	if (pci_dev->current_state == PCI_D3cold) {
+		pci_wakeup_event(pci_dev);
+		pm_runtime_resume(&pci_dev->dev);
+		return;
+	}
+
 	if (!pci_dev->pm_cap || !pci_dev->pme_support
 	     || pci_check_pme_status(pci_dev)) {
 		if (pci_dev->pme_poll)
@@ -187,10 +193,13 @@ acpi_status pci_acpi_remove_pm_notifier(
 
 static pci_power_t acpi_pci_choose_state(struct pci_dev *pdev)
 {
-	int acpi_state;
+	int acpi_state, d_max;
 
-	acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL,
-						ACPI_STATE_D3);
+	if (pdev->no_d3cold)
+		d_max = ACPI_STATE_D3_HOT;
+	else
+		d_max = ACPI_STATE_D3_COLD;
+	acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL, d_max);
 	if (acpi_state < 0)
 		return PCI_POWER_ERROR;
 
@@ -297,7 +306,13 @@ static void acpi_pci_propagate_run_wake(
 
 static int acpi_pci_run_wake(struct pci_dev *dev, bool enable)
 {
-	if (dev->pme_interrupt)
+	/*
+	 * Per PCI Express Base Specification Revision 2.0 section
+	 * 5.3.3.2 Link Wakeup, platform support is needed for D3cold
+	 * waking up to power on the main link even if there is PME
+	 * support for D3cold
+	 */
+	if (dev->pme_interrupt && !dev->runtime_d3cold)
 		return 0;
 
 	if (!acpi_pm_device_run_wake(&dev->dev, enable))
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -1019,10 +1019,13 @@ static int pci_pm_runtime_suspend(struct
 	if (!pm || !pm->runtime_suspend)
 		return -ENOSYS;
 
+	pci_dev->no_d3cold = false;
 	error = pm->runtime_suspend(dev);
 	suspend_report_result(pm->runtime_suspend, error);
 	if (error)
 		return error;
+	if (!pci_dev->d3cold_allowed)
+		pci_dev->no_d3cold = true;
 
 	pci_fixup_device(pci_fixup_suspend, pci_dev);
 
@@ -1044,6 +1047,7 @@ static int pci_pm_runtime_suspend(struct
 
 static int pci_pm_runtime_resume(struct device *dev)
 {
+	int rc;
 	struct pci_dev *pci_dev = to_pci_dev(dev);
 	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
 
@@ -1054,7 +1058,11 @@ static int pci_pm_runtime_resume(struct
 	__pci_enable_wake(pci_dev, PCI_D0, true, false);
 	pci_fixup_device(pci_fixup_resume, pci_dev);
 
-	return pm->runtime_resume(dev);
+	rc = pm->runtime_resume(dev);
+
+	pci_dev->runtime_d3cold = false;
+
+	return rc;
 }
 
 static int pci_pm_runtime_idle(struct device *dev)
--- a/drivers/pci/pci-sysfs.c
+++ b/drivers/pci/pci-sysfs.c
@@ -28,6 +28,7 @@
 #include <linux/pci-aspm.h>
 #include <linux/slab.h>
 #include <linux/vgaarb.h>
+#include <linux/pm_runtime.h>
 #include "pci.h"
 
 static int sysfs_initialized;	/* = 0 */
@@ -378,6 +379,31 @@ dev_bus_rescan_store(struct device *dev,
 
 #endif
 
+#if defined(CONFIG_PM_RUNTIME) && defined(CONFIG_ACPI)
+static ssize_t d3cold_allowed_store(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val) < 0)
+		return -EINVAL;
+
+	pdev->d3cold_allowed = !!val;
+	pm_runtime_resume(dev);
+
+	return count;
+}
+
+static ssize_t d3cold_allowed_show(struct device *dev,
+				   struct device_attribute *attr, char *buf)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	return sprintf (buf, "%u\n", pdev->d3cold_allowed);
+}
+#endif
+
 struct device_attribute pci_dev_attrs[] = {
 	__ATTR_RO(resource),
 	__ATTR_RO(vendor),
@@ -402,6 +428,9 @@ struct device_attribute pci_dev_attrs[]
 	__ATTR(remove, (S_IWUSR|S_IWGRP), NULL, remove_store),
 	__ATTR(rescan, (S_IWUSR|S_IWGRP), NULL, dev_rescan_store),
 #endif
+#if defined(CONFIG_PM_RUNTIME) && defined(CONFIG_ACPI)
+	__ATTR(d3cold_allowed, 0644, d3cold_allowed_show, d3cold_allowed_store),
+#endif
 	__ATTR_NULL,
 };
 
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -622,7 +622,8 @@ static int pci_raw_set_power_state(struc
 		dev_info(&dev->dev, "Refused to change power state, "
 			"currently in D%d\n", dev->current_state);
 
-	/* According to section 5.4.1 of the "PCI BUS POWER MANAGEMENT
+	/*
+	 * According to section 5.4.1 of the "PCI BUS POWER MANAGEMENT
 	 * INTERFACE SPECIFICATION, REV. 1.2", a device transitioning
 	 * from D3hot to D0 _may_ perform an internal reset, thereby
 	 * going to "D0 Uninitialized" rather than "D0 Initialized".
@@ -654,6 +655,16 @@ void pci_update_current_state(struct pci
 	if (dev->pm_cap) {
 		u16 pmcsr;
 
+		/*
+		 * Configuration space is not accessible for device in
+		 * D3cold, so just keep or set D3cold for safety
+		 */
+		if (dev->current_state == PCI_D3cold)
+			return;
+		if (state == PCI_D3cold) {
+			dev->current_state = PCI_D3cold;
+			return;
+		}
 		pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
 		dev->current_state = (pmcsr & PCI_PM_CTRL_STATE_MASK);
 	} else {
@@ -694,8 +705,50 @@ static int pci_platform_power_transition
  */
 static void __pci_start_power_transition(struct pci_dev *dev, pci_power_t state)
 {
-	if (state == PCI_D0)
+	if (state == PCI_D0) {
 		pci_platform_power_transition(dev, PCI_D0);
+		/*
+		 * Mandatory power management transition delays, see
+		 * PCI Express Base Specification Revision 2.0 Section
+		 * 6.6.1: Conventional Reset.  Do not delay for
+		 * devices powered on/off by corresponding bridge,
+		 * because have already delayed for the bridge.
+		 */
+		if (dev->runtime_d3cold) {
+			msleep(dev->d3cold_delay);
+			/*
+			 * When powering on a bridge from D3cold, the
+			 * whole hierarchy may be powered on into
+			 * D0uninitialized state, resume them to give
+			 * them a chance to suspend again
+			 */
+			pci_wakeup_bus(dev->subordinate);
+		}
+	}
+}
+
+/**
+ * __pci_dev_set_current_state - Set current state of a PCI device
+ * @dev: Device to handle
+ * @data: pointer to state to be set
+ */
+static int __pci_dev_set_current_state(struct pci_dev *dev, void *data)
+{
+	pci_power_t state = *(pci_power_t *)data;
+
+	dev->current_state = state;
+	return 0;
+}
+
+/**
+ * __pci_bus_set_current_state - Walk given bus and set current state of devices
+ * @bus: Top bus of the subtree to walk.
+ * @state: state to be set
+ */
+static void __pci_bus_set_current_state(struct pci_bus *bus, pci_power_t state)
+{
+	if (bus)
+		pci_walk_bus(bus, __pci_dev_set_current_state, &state);
 }
 
 /**
@@ -707,8 +760,15 @@ static void __pci_start_power_transition
  */
 int __pci_complete_power_transition(struct pci_dev *dev, pci_power_t state)
 {
-	return state >= PCI_D0 ?
-			pci_platform_power_transition(dev, state) : -EINVAL;
+	int ret;
+
+	if (state < PCI_D0)
+		return -EINVAL;
+	ret = pci_platform_power_transition(dev, state);
+	/* Power off the bridge may power off the whole hierarchy */
+	if (!ret && state == PCI_D3cold)
+		__pci_bus_set_current_state(dev->subordinate, PCI_D3cold);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(__pci_complete_power_transition);
 
@@ -732,8 +792,8 @@ int pci_set_power_state(struct pci_dev *
 	int error;
 
 	/* bound the state we're entering */
-	if (state > PCI_D3hot)
-		state = PCI_D3hot;
+	if (state > PCI_D3cold)
+		state = PCI_D3cold;
 	else if (state < PCI_D0)
 		state = PCI_D0;
 	else if ((state == PCI_D1 || state == PCI_D2) && pci_no_d1d2(dev))
@@ -748,10 +808,15 @@ int pci_set_power_state(struct pci_dev *
 
 	/* This device is quirked not to be put into D3, so
 	   don't put it in D3 */
-	if (state == PCI_D3hot && (dev->dev_flags & PCI_DEV_FLAGS_NO_D3))
+	if (state >= PCI_D3hot && (dev->dev_flags & PCI_DEV_FLAGS_NO_D3))
 		return 0;
 
-	error = pci_raw_set_power_state(dev, state);
+	/*
+	 * To put device in D3cold, we put device into D3hot in native
+	 * way, then put device into D3cold with platform ops
+	 */
+	error = pci_raw_set_power_state(dev, state > PCI_D3hot ?
+					PCI_D3hot : state);
 
 	if (!__pci_complete_power_transition(dev, state))
 		error = 0;
@@ -1498,6 +1563,28 @@ void pci_pme_wakeup_bus(struct pci_bus *
 }
 
 /**
+ * pci_wakeup - Wake up a PCI device
+ * @dev: Device to handle.
+ * @ign: ignored parameter
+ */
+static int pci_wakeup(struct pci_dev *pci_dev, void *ign)
+{
+	pci_wakeup_event(pci_dev);
+	pm_request_resume(&pci_dev->dev);
+	return 0;
+}
+
+/**
+ * pci_wakeup_bus - Walk given bus and wake up devices on it
+ * @bus: Top bus of the subtree to walk.
+ */
+void pci_wakeup_bus(struct pci_bus *bus)
+{
+	if (bus)
+		pci_walk_bus(bus, pci_wakeup, NULL);
+}
+
+/**
  * pci_pme_capable - check the capability of PCI device to generate PME#
  * @dev: PCI device to handle.
  * @state: PCI state from which device will issue PME#.
@@ -1754,6 +1841,10 @@ int pci_prepare_to_sleep(struct pci_dev
 	if (target_state == PCI_POWER_ERROR)
 		return -EIO;
 
+	/* D3cold during system suspend/hibernate is not supported */
+	if (target_state > PCI_D3hot)
+		target_state = PCI_D3hot;
+
 	/* Some devices mustn't be in D3 during system sleep */
 	if (target_state == PCI_D3hot &&
 			(dev->dev_flags & PCI_DEV_FLAGS_NO_D3_DURING_SLEEP))
@@ -1796,12 +1887,16 @@ int pci_finish_runtime_suspend(struct pc
 	if (target_state == PCI_POWER_ERROR)
 		return -EIO;
 
+	dev->runtime_d3cold = target_state == PCI_D3cold;
+
 	__pci_enable_wake(dev, target_state, true, pci_dev_run_wake(dev));
 
 	error = pci_set_power_state(dev, target_state);
 
-	if (error)
+	if (error) {
 		__pci_enable_wake(dev, target_state, true, false);
+		dev->runtime_d3cold = false;
+	}
 
 	return error;
 }
@@ -1871,6 +1966,7 @@ void pci_pm_init(struct pci_dev *dev)
 
 	dev->pm_cap = pm;
 	dev->d3_delay = PCI_PM_D3_WAIT;
+	dev->d3cold_delay = PCI_PM_D3COLD_WAIT;
 
 	dev->d1_support = false;
 	dev->d2_support = false;
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -70,6 +70,7 @@ extern void pci_update_current_state(str
 extern void pci_disable_enabled_device(struct pci_dev *dev);
 extern int pci_finish_runtime_suspend(struct pci_dev *dev);
 extern int __pci_pme_wakeup(struct pci_dev *dev, void *ign);
+extern void pci_wakeup_bus(struct pci_bus *bus);
 extern void pci_pm_init(struct pci_dev *dev);
 extern void platform_pci_wakeup_init(struct pci_dev *dev);
 extern void pci_allocate_cap_save_buffers(struct pci_dev *dev);
--- a/drivers/pci/pcie/portdrv_pci.c
+++ b/drivers/pci/pcie/portdrv_pci.c
@@ -101,12 +101,48 @@ static int pcie_port_resume_noirq(struct
 }
 
 #ifdef CONFIG_PM_RUNTIME
-static int pcie_port_runtime_pm(struct device *dev)
+struct d3cold_info {
+	bool no_d3cold;
+	unsigned int d3cold_delay;
+};
+
+static int pci_dev_d3cold_info(struct pci_dev *pdev, void *data)
+{
+	struct d3cold_info *info = data;
+
+	info->d3cold_delay = max_t(unsigned int, pdev->d3cold_delay,
+				   info->d3cold_delay);
+	if (pdev->no_d3cold)
+		info->no_d3cold = true;
+	return 0;
+}
+
+static int pcie_port_runtime_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct d3cold_info d3cold_info = {
+		.no_d3cold	= false,
+		.d3cold_delay	= PCI_PM_D3_WAIT,
+	};
+
+	/*
+	 * If any subordinate device disable D3cold, we should not put
+	 * the port into D3cold.  The D3cold delay of port should be
+	 * the max of that of all subordinate devices.
+	 */
+	pci_walk_bus(pdev->subordinate, pci_dev_d3cold_info, &d3cold_info);
+	pdev->no_d3cold = d3cold_info.no_d3cold;
+	pdev->d3cold_delay = d3cold_info.d3cold_delay;
+	return 0;
+}
+
+static int pcie_port_runtime_resume(struct device *dev)
 {
 	return 0;
 }
 #else
-#define pcie_port_runtime_pm	NULL
+#define pcie_port_runtime_suspend	NULL
+#define pcie_port_runtime_resume	NULL
 #endif
 
 static const struct dev_pm_ops pcie_portdrv_pm_ops = {
@@ -117,8 +153,8 @@ static const struct dev_pm_ops pcie_port
 	.poweroff	= pcie_port_device_suspend,
 	.restore	= pcie_port_device_resume,
 	.resume_noirq	= pcie_port_resume_noirq,
-	.runtime_suspend = pcie_port_runtime_pm,
-	.runtime_resume = pcie_port_runtime_pm,
+	.runtime_suspend = pcie_port_runtime_suspend,
+	.runtime_resume = pcie_port_runtime_resume,
 };
 
 #define PCIE_PORTDRV_PM_OPS	(&pcie_portdrv_pm_ops)
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -132,9 +132,10 @@ static inline const char *pci_power_name
 	return pci_power_names[1 + (int) state];
 }
 
-#define PCI_PM_D2_DELAY	200
-#define PCI_PM_D3_WAIT	10
-#define PCI_PM_BUS_WAIT	50
+#define PCI_PM_D2_DELAY		200
+#define PCI_PM_D3_WAIT		10
+#define PCI_PM_D3COLD_WAIT	100
+#define PCI_PM_BUS_WAIT		50
 
 /** The pci_channel state describes connectivity between the CPU and
  *  the pci device.  If some PCI bus between here and the pci device
@@ -280,11 +281,18 @@ struct pci_dev {
 	unsigned int	pme_poll:1;	/* Poll device's PME status bit */
 	unsigned int	d1_support:1;	/* Low power state D1 is supported */
 	unsigned int	d2_support:1;	/* Low power state D2 is supported */
-	unsigned int	no_d1d2:1;	/* Only allow D0 and D3 */
+	unsigned int	no_d1d2:1;	/* D1 and D2 are forbidden */
+	unsigned int	no_d3cold:1;	/* D3cold is forbidden */
+	unsigned int	d3cold_allowed:1;	/* D3cold is allowed by user */
 	unsigned int	mmio_always_on:1;	/* disallow turning off io/mem
 						   decoding during bar sizing */
 	unsigned int	wakeup_prepared:1;
+	unsigned int	runtime_d3cold:1;	/* whether go through runtime
+						   D3cold, not set for devices
+						   powered on/off by the
+						   corresponding bridge */
 	unsigned int	d3_delay;	/* D3->D0 transition time in ms */
+	unsigned int	d3cold_delay;	/* D3cold->D0 transition time in ms */
 
 #ifdef CONFIG_PCIEASPM
 	struct pcie_link_state	*link_state;	/* ASPM link state. */

Re: [PATCH -v6 3/4] PCI, PM, Do not call pci_set_power_state with PCI_D3cold

[Rafael J. Wysocki]

On Tuesday, June 19, 2012, Huang Ying wrote:
> PCI subsystem has not been ready for D3cold support yet.  So
> PCI_D3cold should not be used as parameter for pci_set_power_state.
> This patch is needed for upcoming PCI_D3cold support.
> 
> This patch has no functionality change, because pci_set_power_state
> will bound the parameter to PCI_D3hot too.
> 
> Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
> Cc: Jesse Barnes <jesse.barnes@intel.com>
> Signed-off-by: Huang Ying <ying.huang@intel.com>

Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>

> ---
>  arch/x86/pci/mrst.c       |    2 +-
>  drivers/misc/cb710/core.c |    2 +-
>  2 files changed, 2 insertions(+), 2 deletions(-)
> 
> --- a/arch/x86/pci/mrst.c
> +++ b/arch/x86/pci/mrst.c
> @@ -264,7 +264,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_IN
>  
>  static void __devinit mrst_power_off_unused_dev(struct pci_dev *dev)
>  {
> -	pci_set_power_state(dev, PCI_D3cold);
> +	pci_set_power_state(dev, PCI_D3hot);
>  }
>  DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0801, mrst_power_off_unused_dev);
>  DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0809, mrst_power_off_unused_dev);
> --- a/drivers/misc/cb710/core.c
> +++ b/drivers/misc/cb710/core.c
> @@ -180,7 +180,7 @@ static int cb710_suspend(struct pci_dev
>  	pci_save_state(pdev);
>  	pci_disable_device(pdev);
>  	if (state.event & PM_EVENT_SLEEP)
> -		pci_set_power_state(pdev, PCI_D3cold);
> +		pci_set_power_state(pdev, PCI_D3hot);
>  	return 0;
>  }
>  
> 
> 

Re: [PATCH -v6 4/4] PCIe, PM, Add PCIe runtime D3cold support

[Rafael J. Wysocki]

On Tuesday, June 19, 2012, Huang Ying wrote:
> This patch adds runtime D3cold support to PCIe bus.  D3cold is the
> deepest power saving state for PCIe devices.  Where the main PCIe link
> will be powered off totally, so before the PCIe main link is powered
> on again, you can not access the device, even the configuration space,
> which is still accessible in D3hot.  Because the main PCIe link is not
> available, the PCI PM registers can not be used to put device into/out
> of D3cold state, that will be done by platform logic such as ACPI
> _PR3.
> 
> To support remote wake up in D3cold, aux power is supplied, and a
> side-band pin: WAKE# is used to notify remote wake up event, the pin
> is usually connected to platform logic such as ACPI GPE.  This is
> quite different with other power saving states, where remote wake up
> is notified via PME message through the PCIe main link.
> 
> Some PCIe devices usually have no direct platform logic (such as these
> in plug-in slot), for example, there is usually no ACPI _PR3 for them.
> The D3cold support for these devices can be done via the PCIe port
> connected to it.  When power on/off the PCIe port, the corresponding
> PCIe devices are powered on/off too.  And the remote wake up event
> from PCIe device will be notified to the corresponding PCIe port.
> 
> The PCI subsystem runtime D3cold support and corresponding ACPI
> platform support is implemented in the patch.
> 
> This patch only enabled runtime D3cold support for PCI devices.  PCI
> devices D3cold support during system suspend/hibernate is not enabled.
> 
> For more information about PCIe D3cold and corresponding ACPI support,
> please refer to:
> 
> - PCI Express Base Specification Revision 2.0
> - Advanced Configuration and Power Interface Specification Revision 5.0
> 
> Originally-by: Zheng Yan <zheng.z.yan@intel.com>
> Signed-off-by: Huang Ying <ying.huang@intel.com>

Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>

> ---
>  drivers/pci/pci-acpi.c         |   23 ++++++--
>  drivers/pci/pci-driver.c       |   10 +++
>  drivers/pci/pci-sysfs.c        |   29 ++++++++++
>  drivers/pci/pci.c              |  114 +++++++++++++++++++++++++++++++++++++----
>  drivers/pci/pci.h              |    1 
>  drivers/pci/pcie/portdrv_pci.c |   44 ++++++++++++++-
>  include/linux/pci.h            |   16 ++++-
>  7 files changed, 215 insertions(+), 22 deletions(-)
> 
> --- a/drivers/pci/pci-acpi.c
> +++ b/drivers/pci/pci-acpi.c
> @@ -48,6 +48,12 @@ static void pci_acpi_wake_dev(acpi_handl
>  	if (event != ACPI_NOTIFY_DEVICE_WAKE || !pci_dev)
>  		return;
>  
> +	if (pci_dev->current_state == PCI_D3cold) {
> +		pci_wakeup_event(pci_dev);
> +		pm_runtime_resume(&pci_dev->dev);
> +		return;
> +	}
> +
>  	if (!pci_dev->pm_cap || !pci_dev->pme_support
>  	     || pci_check_pme_status(pci_dev)) {
>  		if (pci_dev->pme_poll)
> @@ -187,10 +193,13 @@ acpi_status pci_acpi_remove_pm_notifier(
>  
>  static pci_power_t acpi_pci_choose_state(struct pci_dev *pdev)
>  {
> -	int acpi_state;
> +	int acpi_state, d_max;
>  
> -	acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL,
> -						ACPI_STATE_D3);
> +	if (pdev->no_d3cold)
> +		d_max = ACPI_STATE_D3_HOT;
> +	else
> +		d_max = ACPI_STATE_D3_COLD;
> +	acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL, d_max);
>  	if (acpi_state < 0)
>  		return PCI_POWER_ERROR;
>  
> @@ -297,7 +306,13 @@ static void acpi_pci_propagate_run_wake(
>  
>  static int acpi_pci_run_wake(struct pci_dev *dev, bool enable)
>  {
> -	if (dev->pme_interrupt)
> +	/*
> +	 * Per PCI Express Base Specification Revision 2.0 section
> +	 * 5.3.3.2 Link Wakeup, platform support is needed for D3cold
> +	 * waking up to power on the main link even if there is PME
> +	 * support for D3cold
> +	 */
> +	if (dev->pme_interrupt && !dev->runtime_d3cold)
>  		return 0;
>  
>  	if (!acpi_pm_device_run_wake(&dev->dev, enable))
> --- a/drivers/pci/pci-driver.c
> +++ b/drivers/pci/pci-driver.c
> @@ -1019,10 +1019,13 @@ static int pci_pm_runtime_suspend(struct
>  	if (!pm || !pm->runtime_suspend)
>  		return -ENOSYS;
>  
> +	pci_dev->no_d3cold = false;
>  	error = pm->runtime_suspend(dev);
>  	suspend_report_result(pm->runtime_suspend, error);
>  	if (error)
>  		return error;
> +	if (!pci_dev->d3cold_allowed)
> +		pci_dev->no_d3cold = true;
>  
>  	pci_fixup_device(pci_fixup_suspend, pci_dev);
>  
> @@ -1044,6 +1047,7 @@ static int pci_pm_runtime_suspend(struct
>  
>  static int pci_pm_runtime_resume(struct device *dev)
>  {
> +	int rc;
>  	struct pci_dev *pci_dev = to_pci_dev(dev);
>  	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
>  
> @@ -1054,7 +1058,11 @@ static int pci_pm_runtime_resume(struct
>  	__pci_enable_wake(pci_dev, PCI_D0, true, false);
>  	pci_fixup_device(pci_fixup_resume, pci_dev);
>  
> -	return pm->runtime_resume(dev);
> +	rc = pm->runtime_resume(dev);
> +
> +	pci_dev->runtime_d3cold = false;
> +
> +	return rc;
>  }
>  
>  static int pci_pm_runtime_idle(struct device *dev)
> --- a/drivers/pci/pci-sysfs.c
> +++ b/drivers/pci/pci-sysfs.c
> @@ -28,6 +28,7 @@
>  #include <linux/pci-aspm.h>
>  #include <linux/slab.h>
>  #include <linux/vgaarb.h>
> +#include <linux/pm_runtime.h>
>  #include "pci.h"
>  
>  static int sysfs_initialized;	/* = 0 */
> @@ -378,6 +379,31 @@ dev_bus_rescan_store(struct device *dev,
>  
>  #endif
>  
> +#if defined(CONFIG_PM_RUNTIME) && defined(CONFIG_ACPI)
> +static ssize_t d3cold_allowed_store(struct device *dev,
> +				    struct device_attribute *attr,
> +				    const char *buf, size_t count)
> +{
> +	struct pci_dev *pdev = to_pci_dev(dev);
> +	unsigned long val;
> +
> +	if (strict_strtoul(buf, 0, &val) < 0)
> +		return -EINVAL;
> +
> +	pdev->d3cold_allowed = !!val;
> +	pm_runtime_resume(dev);
> +
> +	return count;
> +}
> +
> +static ssize_t d3cold_allowed_show(struct device *dev,
> +				   struct device_attribute *attr, char *buf)
> +{
> +	struct pci_dev *pdev = to_pci_dev(dev);
> +	return sprintf (buf, "%u\n", pdev->d3cold_allowed);
> +}
> +#endif
> +
>  struct device_attribute pci_dev_attrs[] = {
>  	__ATTR_RO(resource),
>  	__ATTR_RO(vendor),
> @@ -402,6 +428,9 @@ struct device_attribute pci_dev_attrs[]
>  	__ATTR(remove, (S_IWUSR|S_IWGRP), NULL, remove_store),
>  	__ATTR(rescan, (S_IWUSR|S_IWGRP), NULL, dev_rescan_store),
>  #endif
> +#if defined(CONFIG_PM_RUNTIME) && defined(CONFIG_ACPI)
> +	__ATTR(d3cold_allowed, 0644, d3cold_allowed_show, d3cold_allowed_store),
> +#endif
>  	__ATTR_NULL,
>  };
>  
> --- a/drivers/pci/pci.c
> +++ b/drivers/pci/pci.c
> @@ -622,7 +622,8 @@ static int pci_raw_set_power_state(struc
>  		dev_info(&dev->dev, "Refused to change power state, "
>  			"currently in D%d\n", dev->current_state);
>  
> -	/* According to section 5.4.1 of the "PCI BUS POWER MANAGEMENT
> +	/*
> +	 * According to section 5.4.1 of the "PCI BUS POWER MANAGEMENT
>  	 * INTERFACE SPECIFICATION, REV. 1.2", a device transitioning
>  	 * from D3hot to D0 _may_ perform an internal reset, thereby
>  	 * going to "D0 Uninitialized" rather than "D0 Initialized".
> @@ -654,6 +655,16 @@ void pci_update_current_state(struct pci
>  	if (dev->pm_cap) {
>  		u16 pmcsr;
>  
> +		/*
> +		 * Configuration space is not accessible for device in
> +		 * D3cold, so just keep or set D3cold for safety
> +		 */
> +		if (dev->current_state == PCI_D3cold)
> +			return;
> +		if (state == PCI_D3cold) {
> +			dev->current_state = PCI_D3cold;
> +			return;
> +		}
>  		pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
>  		dev->current_state = (pmcsr & PCI_PM_CTRL_STATE_MASK);
>  	} else {
> @@ -694,8 +705,50 @@ static int pci_platform_power_transition
>   */
>  static void __pci_start_power_transition(struct pci_dev *dev, pci_power_t state)
>  {
> -	if (state == PCI_D0)
> +	if (state == PCI_D0) {
>  		pci_platform_power_transition(dev, PCI_D0);
> +		/*
> +		 * Mandatory power management transition delays, see
> +		 * PCI Express Base Specification Revision 2.0 Section
> +		 * 6.6.1: Conventional Reset.  Do not delay for
> +		 * devices powered on/off by corresponding bridge,
> +		 * because have already delayed for the bridge.
> +		 */
> +		if (dev->runtime_d3cold) {
> +			msleep(dev->d3cold_delay);
> +			/*
> +			 * When powering on a bridge from D3cold, the
> +			 * whole hierarchy may be powered on into
> +			 * D0uninitialized state, resume them to give
> +			 * them a chance to suspend again
> +			 */
> +			pci_wakeup_bus(dev->subordinate);
> +		}
> +	}
> +}
> +
> +/**
> + * __pci_dev_set_current_state - Set current state of a PCI device
> + * @dev: Device to handle
> + * @data: pointer to state to be set
> + */
> +static int __pci_dev_set_current_state(struct pci_dev *dev, void *data)
> +{
> +	pci_power_t state = *(pci_power_t *)data;
> +
> +	dev->current_state = state;
> +	return 0;
> +}
> +
> +/**
> + * __pci_bus_set_current_state - Walk given bus and set current state of devices
> + * @bus: Top bus of the subtree to walk.
> + * @state: state to be set
> + */
> +static void __pci_bus_set_current_state(struct pci_bus *bus, pci_power_t state)
> +{
> +	if (bus)
> +		pci_walk_bus(bus, __pci_dev_set_current_state, &state);
>  }
>  
>  /**
> @@ -707,8 +760,15 @@ static void __pci_start_power_transition
>   */
>  int __pci_complete_power_transition(struct pci_dev *dev, pci_power_t state)
>  {
> -	return state >= PCI_D0 ?
> -			pci_platform_power_transition(dev, state) : -EINVAL;
> +	int ret;
> +
> +	if (state < PCI_D0)
> +		return -EINVAL;
> +	ret = pci_platform_power_transition(dev, state);
> +	/* Power off the bridge may power off the whole hierarchy */
> +	if (!ret && state == PCI_D3cold)
> +		__pci_bus_set_current_state(dev->subordinate, PCI_D3cold);
> +	return ret;
>  }
>  EXPORT_SYMBOL_GPL(__pci_complete_power_transition);
>  
> @@ -732,8 +792,8 @@ int pci_set_power_state(struct pci_dev *
>  	int error;
>  
>  	/* bound the state we're entering */
> -	if (state > PCI_D3hot)
> -		state = PCI_D3hot;
> +	if (state > PCI_D3cold)
> +		state = PCI_D3cold;
>  	else if (state < PCI_D0)
>  		state = PCI_D0;
>  	else if ((state == PCI_D1 || state == PCI_D2) && pci_no_d1d2(dev))
> @@ -748,10 +808,15 @@ int pci_set_power_state(struct pci_dev *
>  
>  	/* This device is quirked not to be put into D3, so
>  	   don't put it in D3 */
> -	if (state == PCI_D3hot && (dev->dev_flags & PCI_DEV_FLAGS_NO_D3))
> +	if (state >= PCI_D3hot && (dev->dev_flags & PCI_DEV_FLAGS_NO_D3))
>  		return 0;
>  
> -	error = pci_raw_set_power_state(dev, state);
> +	/*
> +	 * To put device in D3cold, we put device into D3hot in native
> +	 * way, then put device into D3cold with platform ops
> +	 */
> +	error = pci_raw_set_power_state(dev, state > PCI_D3hot ?
> +					PCI_D3hot : state);
>  
>  	if (!__pci_complete_power_transition(dev, state))
>  		error = 0;
> @@ -1498,6 +1563,28 @@ void pci_pme_wakeup_bus(struct pci_bus *
>  }
>  
>  /**
> + * pci_wakeup - Wake up a PCI device
> + * @dev: Device to handle.
> + * @ign: ignored parameter
> + */
> +static int pci_wakeup(struct pci_dev *pci_dev, void *ign)
> +{
> +	pci_wakeup_event(pci_dev);
> +	pm_request_resume(&pci_dev->dev);
> +	return 0;
> +}
> +
> +/**
> + * pci_wakeup_bus - Walk given bus and wake up devices on it
> + * @bus: Top bus of the subtree to walk.
> + */
> +void pci_wakeup_bus(struct pci_bus *bus)
> +{
> +	if (bus)
> +		pci_walk_bus(bus, pci_wakeup, NULL);
> +}
> +
> +/**
>   * pci_pme_capable - check the capability of PCI device to generate PME#
>   * @dev: PCI device to handle.
>   * @state: PCI state from which device will issue PME#.
> @@ -1754,6 +1841,10 @@ int pci_prepare_to_sleep(struct pci_dev
>  	if (target_state == PCI_POWER_ERROR)
>  		return -EIO;
>  
> +	/* D3cold during system suspend/hibernate is not supported */
> +	if (target_state > PCI_D3hot)
> +		target_state = PCI_D3hot;
> +
>  	/* Some devices mustn't be in D3 during system sleep */
>  	if (target_state == PCI_D3hot &&
>  			(dev->dev_flags & PCI_DEV_FLAGS_NO_D3_DURING_SLEEP))
> @@ -1796,12 +1887,16 @@ int pci_finish_runtime_suspend(struct pc
>  	if (target_state == PCI_POWER_ERROR)
>  		return -EIO;
>  
> +	dev->runtime_d3cold = target_state == PCI_D3cold;
> +
>  	__pci_enable_wake(dev, target_state, true, pci_dev_run_wake(dev));
>  
>  	error = pci_set_power_state(dev, target_state);
>  
> -	if (error)
> +	if (error) {
>  		__pci_enable_wake(dev, target_state, true, false);
> +		dev->runtime_d3cold = false;
> +	}
>  
>  	return error;
>  }
> @@ -1871,6 +1966,7 @@ void pci_pm_init(struct pci_dev *dev)
>  
>  	dev->pm_cap = pm;
>  	dev->d3_delay = PCI_PM_D3_WAIT;
> +	dev->d3cold_delay = PCI_PM_D3COLD_WAIT;
>  
>  	dev->d1_support = false;
>  	dev->d2_support = false;
> --- a/drivers/pci/pci.h
> +++ b/drivers/pci/pci.h
> @@ -70,6 +70,7 @@ extern void pci_update_current_state(str
>  extern void pci_disable_enabled_device(struct pci_dev *dev);
>  extern int pci_finish_runtime_suspend(struct pci_dev *dev);
>  extern int __pci_pme_wakeup(struct pci_dev *dev, void *ign);
> +extern void pci_wakeup_bus(struct pci_bus *bus);
>  extern void pci_pm_init(struct pci_dev *dev);
>  extern void platform_pci_wakeup_init(struct pci_dev *dev);
>  extern void pci_allocate_cap_save_buffers(struct pci_dev *dev);
> --- a/drivers/pci/pcie/portdrv_pci.c
> +++ b/drivers/pci/pcie/portdrv_pci.c
> @@ -101,12 +101,48 @@ static int pcie_port_resume_noirq(struct
>  }
>  
>  #ifdef CONFIG_PM_RUNTIME
> -static int pcie_port_runtime_pm(struct device *dev)
> +struct d3cold_info {
> +	bool no_d3cold;
> +	unsigned int d3cold_delay;
> +};
> +
> +static int pci_dev_d3cold_info(struct pci_dev *pdev, void *data)
> +{
> +	struct d3cold_info *info = data;
> +
> +	info->d3cold_delay = max_t(unsigned int, pdev->d3cold_delay,
> +				   info->d3cold_delay);
> +	if (pdev->no_d3cold)
> +		info->no_d3cold = true;
> +	return 0;
> +}
> +
> +static int pcie_port_runtime_suspend(struct device *dev)
> +{
> +	struct pci_dev *pdev = to_pci_dev(dev);
> +	struct d3cold_info d3cold_info = {
> +		.no_d3cold	= false,
> +		.d3cold_delay	= PCI_PM_D3_WAIT,
> +	};
> +
> +	/*
> +	 * If any subordinate device disable D3cold, we should not put
> +	 * the port into D3cold.  The D3cold delay of port should be
> +	 * the max of that of all subordinate devices.
> +	 */
> +	pci_walk_bus(pdev->subordinate, pci_dev_d3cold_info, &d3cold_info);
> +	pdev->no_d3cold = d3cold_info.no_d3cold;
> +	pdev->d3cold_delay = d3cold_info.d3cold_delay;
> +	return 0;
> +}
> +
> +static int pcie_port_runtime_resume(struct device *dev)
>  {
>  	return 0;
>  }
>  #else
> -#define pcie_port_runtime_pm	NULL
> +#define pcie_port_runtime_suspend	NULL
> +#define pcie_port_runtime_resume	NULL
>  #endif
>  
>  static const struct dev_pm_ops pcie_portdrv_pm_ops = {
> @@ -117,8 +153,8 @@ static const struct dev_pm_ops pcie_port
>  	.poweroff	= pcie_port_device_suspend,
>  	.restore	= pcie_port_device_resume,
>  	.resume_noirq	= pcie_port_resume_noirq,
> -	.runtime_suspend = pcie_port_runtime_pm,
> -	.runtime_resume = pcie_port_runtime_pm,
> +	.runtime_suspend = pcie_port_runtime_suspend,
> +	.runtime_resume = pcie_port_runtime_resume,
>  };
>  
>  #define PCIE_PORTDRV_PM_OPS	(&pcie_portdrv_pm_ops)
> --- a/include/linux/pci.h
> +++ b/include/linux/pci.h
> @@ -132,9 +132,10 @@ static inline const char *pci_power_name
>  	return pci_power_names[1 + (int) state];
>  }
>  
> -#define PCI_PM_D2_DELAY	200
> -#define PCI_PM_D3_WAIT	10
> -#define PCI_PM_BUS_WAIT	50
> +#define PCI_PM_D2_DELAY		200
> +#define PCI_PM_D3_WAIT		10
> +#define PCI_PM_D3COLD_WAIT	100
> +#define PCI_PM_BUS_WAIT		50
>  
>  /** The pci_channel state describes connectivity between the CPU and
>   *  the pci device.  If some PCI bus between here and the pci device
> @@ -280,11 +281,18 @@ struct pci_dev {
>  	unsigned int	pme_poll:1;	/* Poll device's PME status bit */
>  	unsigned int	d1_support:1;	/* Low power state D1 is supported */
>  	unsigned int	d2_support:1;	/* Low power state D2 is supported */
> -	unsigned int	no_d1d2:1;	/* Only allow D0 and D3 */
> +	unsigned int	no_d1d2:1;	/* D1 and D2 are forbidden */
> +	unsigned int	no_d3cold:1;	/* D3cold is forbidden */
> +	unsigned int	d3cold_allowed:1;	/* D3cold is allowed by user */
>  	unsigned int	mmio_always_on:1;	/* disallow turning off io/mem
>  						   decoding during bar sizing */
>  	unsigned int	wakeup_prepared:1;
> +	unsigned int	runtime_d3cold:1;	/* whether go through runtime
> +						   D3cold, not set for devices
> +						   powered on/off by the
> +						   corresponding bridge */
>  	unsigned int	d3_delay;	/* D3->D0 transition time in ms */
> +	unsigned int	d3cold_delay;	/* D3cold->D0 transition time in ms */
>  
>  #ifdef CONFIG_PCIEASPM
>  	struct pcie_link_state	*link_state;	/* ASPM link state. */
> 
> 

Re: [PATCH -v6 0/4] PCIe, PM, Add PCIe runtime D3cold support

[Bjorn Helgaas]

On Mon, Jun 18, 2012 at 11:20 PM, Huang Ying <ying.huang@intel.com> wrote:
> Changelog:
>
> v6:
>
> - Disable device D3cold during system suspend/hibernate with a new method per Rafeal's comments
>
> v5:
>
> - Disable device D3cold during system suspend/hibernate per Rafael's comments
>
> v4:
>
> - Minors fixes based on comments from Rafael
>
> v3:
>
> - Drop device.power.power_must_be_on, use pci_dev.no_d3cold instead
> - Drop device.power.power_off_user, use pci_dev.d3cold_allowed instead
> - Use black list instead of white list in pcie port runtime support per request from Bjorn
> - Various fixes based on comments from Rafael
>
> v2:
>
> - Refreshed based on comments from Rafael
>
> [PATCH -v6 1/4] ACPI, PM, Specify lowest allowed state for device sleep
> [PATCH -v6 2/4] PCIe, PM, Add runtime PM support to PCIe port
> [PATCH -v6 3/4] PCI, PM, Do not call pci_set_power_state with PCI_D3cold
> [PATCH -v6 4/4] PCIe, PM, Add PCIe runtime D3cold support

What kernel is this series based on?  Patch 4/4 doesn't apply to my
tree.  This hunk fails because I don't have the "Some devices mustn't
be in D3 ..." context:

@@ -1754,6 +1841,10 @@ int pci_prepare_to_sleep(struct pci_dev
        if (target_state == PCI_POWER_ERROR)
                return -EIO;

+       /* D3cold during system suspend/hibernate is not supported */
+       if (target_state > PCI_D3hot)
+               target_state = PCI_D3hot;
+
        /* Some devices mustn't be in D3 during system sleep */
        if (target_state == PCI_D3hot &&
                        (dev->dev_flags & PCI_DEV_FLAGS_NO_D3_DURING_SLEEP))

Re: [PATCH -v6 0/4] PCIe, PM, Add PCIe runtime D3cold support

[Rafael J. Wysocki]

On Saturday, June 23, 2012, Bjorn Helgaas wrote:
> On Mon, Jun 18, 2012 at 11:20 PM, Huang Ying <ying.huang@intel.com> wrote:
> > Changelog:
> >
> > v6:
> >
> > - Disable device D3cold during system suspend/hibernate with a new method per Rafeal's comments
> >
> > v5:
> >
> > - Disable device D3cold during system suspend/hibernate per Rafael's comments
> >
> > v4:
> >
> > - Minors fixes based on comments from Rafael
> >
> > v3:
> >
> > - Drop device.power.power_must_be_on, use pci_dev.no_d3cold instead
> > - Drop device.power.power_off_user, use pci_dev.d3cold_allowed instead
> > - Use black list instead of white list in pcie port runtime support per request from Bjorn
> > - Various fixes based on comments from Rafael
> >
> > v2:
> >
> > - Refreshed based on comments from Rafael
> >
> > [PATCH -v6 1/4] ACPI, PM, Specify lowest allowed state for device sleep
> > [PATCH -v6 2/4] PCIe, PM, Add runtime PM support to PCIe port
> > [PATCH -v6 3/4] PCI, PM, Do not call pci_set_power_state with PCI_D3cold
> > [PATCH -v6 4/4] PCIe, PM, Add PCIe runtime D3cold support
> 
> What kernel is this series based on?  Patch 4/4 doesn't apply to my
> tree.  This hunk fails because I don't have the "Some devices mustn't
> be in D3 ..." context:

I think it's based on an ACPI patch that didn't go in due to the problem
with the Len's tree.

Huang, can you please resend the series along with that patch?

Rafael


> @@ -1754,6 +1841,10 @@ int pci_prepare_to_sleep(struct pci_dev
>         if (target_state == PCI_POWER_ERROR)
>                 return -EIO;
> 
> +       /* D3cold during system suspend/hibernate is not supported */
> +       if (target_state > PCI_D3hot)
> +               target_state = PCI_D3hot;
> +
>         /* Some devices mustn't be in D3 during system sleep */
>         if (target_state == PCI_D3hot &&
>                         (dev->dev_flags & PCI_DEV_FLAGS_NO_D3_DURING_SLEEP))
> 
> 

Re: [PATCH -v6 0/4] PCIe, PM, Add PCIe runtime D3cold support

[huang ying]

Hi, Bjorn,

On Sat, Jun 23, 2012 at 6:13 AM, Bjorn Helgaas <bhelgaas@google.com> wrote:
> On Mon, Jun 18, 2012 at 11:20 PM, Huang Ying <ying.huang@intel.com> wrote:
>> Changelog:
>>
>> v6:
>>
>> - Disable device D3cold during system suspend/hibernate with a new method per Rafeal's comments
>>
>> v5:
>>
>> - Disable device D3cold during system suspend/hibernate per Rafael's comments
>>
>> v4:
>>
>> - Minors fixes based on comments from Rafael
>>
>> v3:
>>
>> - Drop device.power.power_must_be_on, use pci_dev.no_d3cold instead
>> - Drop device.power.power_off_user, use pci_dev.d3cold_allowed instead
>> - Use black list instead of white list in pcie port runtime support per request from Bjorn
>> - Various fixes based on comments from Rafael
>>
>> v2:
>>
>> - Refreshed based on comments from Rafael
>>
>> [PATCH -v6 1/4] ACPI, PM, Specify lowest allowed state for device sleep
>> [PATCH -v6 2/4] PCIe, PM, Add runtime PM support to PCIe port
>> [PATCH -v6 3/4] PCI, PM, Do not call pci_set_power_state with PCI_D3cold
>> [PATCH -v6 4/4] PCIe, PM, Add PCIe runtime D3cold support
>
> What kernel is this series based on?  Patch 4/4 doesn't apply to my
> tree.  This hunk fails because I don't have the "Some devices mustn't
> be in D3 ..." context:

This patchset is based on Linus' tree 3.5-rc3.  I will check with your tree.

Best Regards,
Huang Ying