[PATCH v2 0/2] omap: add ocp2scp as a bus driver

[PATCH v2 0/2] omap: add ocp2scp as a bus driver

[Kishon Vijay Abraham I]

This patch series is done as a preparatory step for adding phy drivers
for dwc3 and musb.

This series adds a new driver for ocp2scp (only dt) to which phy
drivers are connected.

Since currently there is no generic way to create a child device along
with doing a pm_runtime_enable (the exact requirement for ocp2scp), I'm
creating a separate driver for ocp2scp.

Changes from v1:
Fixed Sergei's comments to remove the address in the node name of ocp2scp
since the ocp2scp node doesn't have a reg property.

Changes from [RFC PATCH v2 0/2] omap: add ocp2scp as a misc driver:
Created a new folder drivers/bus and moved ocp2scp driver from misc to
drivers/bus.

This patch was developed and tested on
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git

Kishon Vijay Abraham I (2):
  drivers: bus: add a new driver for omap-ocp2scp
  arm/dts: omap4: Add ocp2scp data

 .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
 arch/arm/boot/dts/omap4.dtsi                       |    8 ++
 drivers/Kconfig                                    |    2 +
 drivers/Makefile                                   |    2 +
 drivers/bus/Kconfig                                |   15 +++
 drivers/bus/Makefile                               |    5 +
 drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
 7 files changed, 140 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
 create mode 100644 drivers/bus/Kconfig
 create mode 100644 drivers/bus/Makefile
 create mode 100644 drivers/bus/omap-ocp2scp.c

-- 
1.7.5.4

[PATCH v2 0/2] omap: add ocp2scp as a bus driver

[Kishon Vijay Abraham I]

This patch series is done as a preparatory step for adding phy drivers
for dwc3 and musb.

This series adds a new driver for ocp2scp (only dt) to which phy
drivers are connected.

Since currently there is no generic way to create a child device along
with doing a pm_runtime_enable (the exact requirement for ocp2scp), I'm
creating a separate driver for ocp2scp.

Changes from v1:
Fixed Sergei's comments to remove the address in the node name of ocp2scp
since the ocp2scp node doesn't have a reg property.

Changes from [RFC PATCH v2 0/2] omap: add ocp2scp as a misc driver:
Created a new folder drivers/bus and moved ocp2scp driver from misc to
drivers/bus.

This patch was developed and tested on
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git

Kishon Vijay Abraham I (2):
  drivers: bus: add a new driver for omap-ocp2scp
  arm/dts: omap4: Add ocp2scp data

 .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
 arch/arm/boot/dts/omap4.dtsi                       |    8 ++
 drivers/Kconfig                                    |    2 +
 drivers/Makefile                                   |    2 +
 drivers/bus/Kconfig                                |   15 +++
 drivers/bus/Makefile                               |    5 +
 drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
 7 files changed, 140 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
 create mode 100644 drivers/bus/Kconfig
 create mode 100644 drivers/bus/Makefile
 create mode 100644 drivers/bus/omap-ocp2scp.c

-- 
1.7.5.4

[PATCH v2 0/2] omap: add ocp2scp as a bus driver

[Kishon Vijay Abraham I]

This patch series is done as a preparatory step for adding phy drivers
for dwc3 and musb.

This series adds a new driver for ocp2scp (only dt) to which phy
drivers are connected.

Since currently there is no generic way to create a child device along
with doing a pm_runtime_enable (the exact requirement for ocp2scp), I'm
creating a separate driver for ocp2scp.

Changes from v1:
Fixed Sergei's comments to remove the address in the node name of ocp2scp
since the ocp2scp node doesn't have a reg property.

Changes from [RFC PATCH v2 0/2] omap: add ocp2scp as a misc driver:
Created a new folder drivers/bus and moved ocp2scp driver from misc to
drivers/bus.

This patch was developed and tested on
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git

Kishon Vijay Abraham I (2):
  drivers: bus: add a new driver for omap-ocp2scp
  arm/dts: omap4: Add ocp2scp data

 .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
 arch/arm/boot/dts/omap4.dtsi                       |    8 ++
 drivers/Kconfig                                    |    2 +
 drivers/Makefile                                   |    2 +
 drivers/bus/Kconfig                                |   15 +++
 drivers/bus/Makefile                               |    5 +
 drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
 7 files changed, 140 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
 create mode 100644 drivers/bus/Kconfig
 create mode 100644 drivers/bus/Makefile
 create mode 100644 drivers/bus/omap-ocp2scp.c

-- 
1.7.5.4

[PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[Kishon Vijay Abraham I]

Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
USB2PHY is connected to ocp2scp.

This also includes device tree support for ocp2scp driver and
the documentation with device tree binding information is updated.

Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
 drivers/Kconfig                                    |    2 +
 drivers/Makefile                                   |    2 +
 drivers/bus/Kconfig                                |   15 +++
 drivers/bus/Makefile                               |    5 +
 drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
 6 files changed, 132 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
 create mode 100644 drivers/bus/Kconfig
 create mode 100644 drivers/bus/Makefile
 create mode 100644 drivers/bus/omap-ocp2scp.c

diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
new file mode 100644
index 0000000..d2fe064
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -0,0 +1,10 @@
+* OMAP OCP2SCP - ocp interface to scp interface
+
+properties:
+- compatible : Should be "ti,omap-ocp2scp"
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ranges : the child address space are mapped 1:1 onto the parent address space
+- ti,hwmods : must be "ocp2scp_usb_phy"
+
+Sub-nodes:
+All the devices connected to ocp2scp are described using sub-node to ocp2scp
diff --git a/drivers/Kconfig b/drivers/Kconfig
index bfc9186..4fe1e4c 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -2,6 +2,8 @@ menu "Device Drivers"
 
 source "drivers/base/Kconfig"
 
+source "drivers/bus/Kconfig"
+
 source "drivers/connector/Kconfig"
 
 source "drivers/mtd/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 2ba29ff..cac3819 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -5,6 +5,8 @@
 # Rewritten to use lists instead of if-statements.
 #
 
+obj-y				+= bus/
+
 # GPIO must come after pinctrl as gpios may need to mux pins etc
 obj-y				+= pinctrl/
 obj-y				+= gpio/
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
new file mode 100644
index 0000000..6270415
--- /dev/null
+++ b/drivers/bus/Kconfig
@@ -0,0 +1,15 @@
+#
+# Bus Devices
+#
+
+menu "Bus devices"
+
+config OMAP_OCP2SCP
+	tristate "OMAP OCP2SCP DRIVER"
+	help
+	  Driver to enable ocp2scp module which transforms ocp interface
+	  protocol to scp protocol. In OMAP4, USB PHY is connected via
+	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
+	  OCP2SCP.
+
+endmenu
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
new file mode 100644
index 0000000..0ec50bc
--- /dev/null
+++ b/drivers/bus/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the bus drivers.
+#
+
+obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
new file mode 100644
index 0000000..8c3db3a
--- /dev/null
+++ b/drivers/bus/omap-ocp2scp.c
@@ -0,0 +1,98 @@
+/*
+ * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+
+static int ocp2scp_remove_devices(struct device *dev, void *c)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	platform_device_unregister(pdev);
+
+	return 0;
+}
+
+static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
+{
+	int			ret;
+	struct device_node	*np = pdev->dev.of_node;
+
+	if (np) {
+		ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
+			goto err0;
+		}
+	}
+	pm_runtime_enable(&pdev->dev);
+
+	return 0;
+
+err0:
+	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
+
+	return ret;
+}
+
+static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_ocp2scp_id_table[] = {
+	{ .compatible = "ti,omap-ocp2scp" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+#endif
+
+static struct platform_driver omap_ocp2scp_driver = {
+	.probe		= omap_ocp2scp_probe,
+	.remove		= __devexit_p(omap_ocp2scp_remove),
+	.driver		= {
+		.name	= "omap-ocp2scp",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(omap_ocp2scp_id_table),
+	},
+};
+
+static int __init omap_ocp2scp_init(void)
+{
+	return platform_driver_register(&omap_ocp2scp_driver);
+}
+arch_initcall(omap_ocp2scp_init);
+
+static void __exit omap_ocp2scp_exit(void)
+{
+	platform_driver_unregister(&omap_ocp2scp_driver);
+}
+module_exit(omap_ocp2scp_exit);
+
+MODULE_ALIAS("platform: omap-ocp2scp");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP OCP2SCP DRIVER");
+MODULE_LICENSE("GPLv2");
-- 
1.7.5.4

[PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[Kishon Vijay Abraham I]

Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
USB2PHY is connected to ocp2scp.

This also includes device tree support for ocp2scp driver and
the documentation with device tree binding information is updated.

Cc: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>
Acked-by: Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
---
 .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
 drivers/Kconfig                                    |    2 +
 drivers/Makefile                                   |    2 +
 drivers/bus/Kconfig                                |   15 +++
 drivers/bus/Makefile                               |    5 +
 drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
 6 files changed, 132 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
 create mode 100644 drivers/bus/Kconfig
 create mode 100644 drivers/bus/Makefile
 create mode 100644 drivers/bus/omap-ocp2scp.c

diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
new file mode 100644
index 0000000..d2fe064
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -0,0 +1,10 @@
+* OMAP OCP2SCP - ocp interface to scp interface
+
+properties:
+- compatible : Should be "ti,omap-ocp2scp"
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ranges : the child address space are mapped 1:1 onto the parent address space
+- ti,hwmods : must be "ocp2scp_usb_phy"
+
+Sub-nodes:
+All the devices connected to ocp2scp are described using sub-node to ocp2scp
diff --git a/drivers/Kconfig b/drivers/Kconfig
index bfc9186..4fe1e4c 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -2,6 +2,8 @@ menu "Device Drivers"
 
 source "drivers/base/Kconfig"
 
+source "drivers/bus/Kconfig"
+
 source "drivers/connector/Kconfig"
 
 source "drivers/mtd/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 2ba29ff..cac3819 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -5,6 +5,8 @@
 # Rewritten to use lists instead of if-statements.
 #
 
+obj-y				+= bus/
+
 # GPIO must come after pinctrl as gpios may need to mux pins etc
 obj-y				+= pinctrl/
 obj-y				+= gpio/
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
new file mode 100644
index 0000000..6270415
--- /dev/null
+++ b/drivers/bus/Kconfig
@@ -0,0 +1,15 @@
+#
+# Bus Devices
+#
+
+menu "Bus devices"
+
+config OMAP_OCP2SCP
+	tristate "OMAP OCP2SCP DRIVER"
+	help
+	  Driver to enable ocp2scp module which transforms ocp interface
+	  protocol to scp protocol. In OMAP4, USB PHY is connected via
+	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
+	  OCP2SCP.
+
+endmenu
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
new file mode 100644
index 0000000..0ec50bc
--- /dev/null
+++ b/drivers/bus/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the bus drivers.
+#
+
+obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
new file mode 100644
index 0000000..8c3db3a
--- /dev/null
+++ b/drivers/bus/omap-ocp2scp.c
@@ -0,0 +1,98 @@
+/*
+ * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+
+static int ocp2scp_remove_devices(struct device *dev, void *c)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	platform_device_unregister(pdev);
+
+	return 0;
+}
+
+static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
+{
+	int			ret;
+	struct device_node	*np = pdev->dev.of_node;
+
+	if (np) {
+		ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
+			goto err0;
+		}
+	}
+	pm_runtime_enable(&pdev->dev);
+
+	return 0;
+
+err0:
+	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
+
+	return ret;
+}
+
+static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_ocp2scp_id_table[] = {
+	{ .compatible = "ti,omap-ocp2scp" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+#endif
+
+static struct platform_driver omap_ocp2scp_driver = {
+	.probe		= omap_ocp2scp_probe,
+	.remove		= __devexit_p(omap_ocp2scp_remove),
+	.driver		= {
+		.name	= "omap-ocp2scp",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(omap_ocp2scp_id_table),
+	},
+};
+
+static int __init omap_ocp2scp_init(void)
+{
+	return platform_driver_register(&omap_ocp2scp_driver);
+}
+arch_initcall(omap_ocp2scp_init);
+
+static void __exit omap_ocp2scp_exit(void)
+{
+	platform_driver_unregister(&omap_ocp2scp_driver);
+}
+module_exit(omap_ocp2scp_exit);
+
+MODULE_ALIAS("platform: omap-ocp2scp");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP OCP2SCP DRIVER");
+MODULE_LICENSE("GPLv2");
-- 
1.7.5.4

[PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[Kishon Vijay Abraham I]

Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
USB2PHY is connected to ocp2scp.

This also includes device tree support for ocp2scp driver and
the documentation with device tree binding information is updated.

Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
 drivers/Kconfig                                    |    2 +
 drivers/Makefile                                   |    2 +
 drivers/bus/Kconfig                                |   15 +++
 drivers/bus/Makefile                               |    5 +
 drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
 6 files changed, 132 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
 create mode 100644 drivers/bus/Kconfig
 create mode 100644 drivers/bus/Makefile
 create mode 100644 drivers/bus/omap-ocp2scp.c

diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
new file mode 100644
index 0000000..d2fe064
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -0,0 +1,10 @@
+* OMAP OCP2SCP - ocp interface to scp interface
+
+properties:
+- compatible : Should be "ti,omap-ocp2scp"
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ranges : the child address space are mapped 1:1 onto the parent address space
+- ti,hwmods : must be "ocp2scp_usb_phy"
+
+Sub-nodes:
+All the devices connected to ocp2scp are described using sub-node to ocp2scp
diff --git a/drivers/Kconfig b/drivers/Kconfig
index bfc9186..4fe1e4c 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -2,6 +2,8 @@ menu "Device Drivers"
 
 source "drivers/base/Kconfig"
 
+source "drivers/bus/Kconfig"
+
 source "drivers/connector/Kconfig"
 
 source "drivers/mtd/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 2ba29ff..cac3819 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -5,6 +5,8 @@
 # Rewritten to use lists instead of if-statements.
 #
 
+obj-y				+= bus/
+
 # GPIO must come after pinctrl as gpios may need to mux pins etc
 obj-y				+= pinctrl/
 obj-y				+= gpio/
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
new file mode 100644
index 0000000..6270415
--- /dev/null
+++ b/drivers/bus/Kconfig
@@ -0,0 +1,15 @@
+#
+# Bus Devices
+#
+
+menu "Bus devices"
+
+config OMAP_OCP2SCP
+	tristate "OMAP OCP2SCP DRIVER"
+	help
+	  Driver to enable ocp2scp module which transforms ocp interface
+	  protocol to scp protocol. In OMAP4, USB PHY is connected via
+	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
+	  OCP2SCP.
+
+endmenu
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
new file mode 100644
index 0000000..0ec50bc
--- /dev/null
+++ b/drivers/bus/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the bus drivers.
+#
+
+obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
new file mode 100644
index 0000000..8c3db3a
--- /dev/null
+++ b/drivers/bus/omap-ocp2scp.c
@@ -0,0 +1,98 @@
+/*
+ * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+
+static int ocp2scp_remove_devices(struct device *dev, void *c)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	platform_device_unregister(pdev);
+
+	return 0;
+}
+
+static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
+{
+	int			ret;
+	struct device_node	*np = pdev->dev.of_node;
+
+	if (np) {
+		ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
+			goto err0;
+		}
+	}
+	pm_runtime_enable(&pdev->dev);
+
+	return 0;
+
+err0:
+	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
+
+	return ret;
+}
+
+static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_ocp2scp_id_table[] = {
+	{ .compatible = "ti,omap-ocp2scp" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+#endif
+
+static struct platform_driver omap_ocp2scp_driver = {
+	.probe		= omap_ocp2scp_probe,
+	.remove		= __devexit_p(omap_ocp2scp_remove),
+	.driver		= {
+		.name	= "omap-ocp2scp",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(omap_ocp2scp_id_table),
+	},
+};
+
+static int __init omap_ocp2scp_init(void)
+{
+	return platform_driver_register(&omap_ocp2scp_driver);
+}
+arch_initcall(omap_ocp2scp_init);
+
+static void __exit omap_ocp2scp_exit(void)
+{
+	platform_driver_unregister(&omap_ocp2scp_driver);
+}
+module_exit(omap_ocp2scp_exit);
+
+MODULE_ALIAS("platform: omap-ocp2scp");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP OCP2SCP DRIVER");
+MODULE_LICENSE("GPLv2");
-- 
1.7.5.4

[PATCH v2 2/2] arm/dts: omap4: Add ocp2scp data

[Kishon Vijay Abraham I]

Add ocp2scp data node in omap4 device tree file.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/omap4.dtsi |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 359c497..29c6243 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -272,5 +272,13 @@
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
 		};
+
+		ocp2scp {
+			compatible = "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp_usb_phy";
+		};
 	};
 };
-- 
1.7.5.4

[PATCH v2 2/2] arm/dts: omap4: Add ocp2scp data

[Kishon Vijay Abraham I]

Add ocp2scp data node in omap4 device tree file.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/omap4.dtsi |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 359c497..29c6243 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -272,5 +272,13 @@
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
 		};
+
+		ocp2scp {
+			compatible = "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp_usb_phy";
+		};
 	};
 };
-- 
1.7.5.4

[PATCH v2 2/2] arm/dts: omap4: Add ocp2scp data

[Kishon Vijay Abraham I]

Add ocp2scp data node in omap4 device tree file.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/omap4.dtsi |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 359c497..29c6243 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -272,5 +272,13 @@
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
 		};
+
+		ocp2scp {
+			compatible = "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp_usb_phy";
+		};
 	};
 };
-- 
1.7.5.4

Re: [PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 6630 bytes --]

Hi,

On Wed, Jul 18, 2012 at 12:00:38PM +0530, Kishon Vijay Abraham I wrote:
> Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
> creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
> USB2PHY is connected to ocp2scp.
> 
> This also includes device tree support for ocp2scp driver and
> the documentation with device tree binding information is updated.
> 
> Cc: Felipe Balbi <balbi@ti.com>

If you fix (or change my mind) on the comment below, you can add:

Acked-by: Felipe Balbi <balbi@ti.com>


Also, I wonder who should be the one to take this. Who will be queueing
patches on this directory to mainline ?

> Acked-by: Arnd Bergmann <arnd@arndb.de>
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
>  drivers/Kconfig                                    |    2 +
>  drivers/Makefile                                   |    2 +
>  drivers/bus/Kconfig                                |   15 +++
>  drivers/bus/Makefile                               |    5 +
>  drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
>  6 files changed, 132 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>  create mode 100644 drivers/bus/Kconfig
>  create mode 100644 drivers/bus/Makefile
>  create mode 100644 drivers/bus/omap-ocp2scp.c
> 
> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> new file mode 100644
> index 0000000..d2fe064
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> @@ -0,0 +1,10 @@
> +* OMAP OCP2SCP - ocp interface to scp interface
> +
> +properties:
> +- compatible : Should be "ti,omap-ocp2scp"
> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
> +- ranges : the child address space are mapped 1:1 onto the parent address space
> +- ti,hwmods : must be "ocp2scp_usb_phy"
> +
> +Sub-nodes:
> +All the devices connected to ocp2scp are described using sub-node to ocp2scp
> diff --git a/drivers/Kconfig b/drivers/Kconfig
> index bfc9186..4fe1e4c 100644
> --- a/drivers/Kconfig
> +++ b/drivers/Kconfig
> @@ -2,6 +2,8 @@ menu "Device Drivers"
>  
>  source "drivers/base/Kconfig"
>  
> +source "drivers/bus/Kconfig"
> +
>  source "drivers/connector/Kconfig"
>  
>  source "drivers/mtd/Kconfig"
> diff --git a/drivers/Makefile b/drivers/Makefile
> index 2ba29ff..cac3819 100644
> --- a/drivers/Makefile
> +++ b/drivers/Makefile
> @@ -5,6 +5,8 @@
>  # Rewritten to use lists instead of if-statements.
>  #
>  
> +obj-y				+= bus/
> +
>  # GPIO must come after pinctrl as gpios may need to mux pins etc
>  obj-y				+= pinctrl/
>  obj-y				+= gpio/
> diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
> new file mode 100644
> index 0000000..6270415
> --- /dev/null
> +++ b/drivers/bus/Kconfig
> @@ -0,0 +1,15 @@
> +#
> +# Bus Devices
> +#
> +
> +menu "Bus devices"
> +
> +config OMAP_OCP2SCP
> +	tristate "OMAP OCP2SCP DRIVER"
> +	help
> +	  Driver to enable ocp2scp module which transforms ocp interface
> +	  protocol to scp protocol. In OMAP4, USB PHY is connected via
> +	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
> +	  OCP2SCP.
> +
> +endmenu
> diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
> new file mode 100644
> index 0000000..0ec50bc
> --- /dev/null
> +++ b/drivers/bus/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for the bus drivers.
> +#
> +
> +obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
> diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
> new file mode 100644
> index 0000000..8c3db3a
> --- /dev/null
> +++ b/drivers/bus/omap-ocp2scp.c
> @@ -0,0 +1,98 @@
> +/*
> + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
> + *
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Author: Kishon Vijay Abraham I <kishon@ti.com>
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/err.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +
> +static int ocp2scp_remove_devices(struct device *dev, void *c)
> +{
> +	struct platform_device *pdev = to_platform_device(dev);
> +
> +	platform_device_unregister(pdev);
> +
> +	return 0;
> +}
> +
> +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
> +{
> +	int			ret;
> +	struct device_node	*np = pdev->dev.of_node;
> +
> +	if (np) {
> +		ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
> +		if (ret) {
> +			dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
> +			goto err0;
> +		}
> +	}
> +	pm_runtime_enable(&pdev->dev);
> +
> +	return 0;
> +
> +err0:
> +	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
> +
> +	return ret;
> +}
> +
> +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
> +{
> +	pm_runtime_disable(&pdev->dev);
> +	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id omap_ocp2scp_id_table[] = {
> +	{ .compatible = "ti,omap-ocp2scp" },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
> +#endif
> +
> +static struct platform_driver omap_ocp2scp_driver = {
> +	.probe		= omap_ocp2scp_probe,
> +	.remove		= __devexit_p(omap_ocp2scp_remove),
> +	.driver		= {
> +		.name	= "omap-ocp2scp",
> +		.owner	= THIS_MODULE,
> +		.of_match_table = of_match_ptr(omap_ocp2scp_id_table),
> +	},
> +};
> +
> +static int __init omap_ocp2scp_init(void)
> +{
> +	return platform_driver_register(&omap_ocp2scp_driver);
> +}
> +arch_initcall(omap_ocp2scp_init);

I really think we should avoid this trickery and make dependent drivers
return -EPROBE_DEFER case this isn't ready yet.

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 6738 bytes --]

Hi,

On Wed, Jul 18, 2012 at 12:00:38PM +0530, Kishon Vijay Abraham I wrote:
> Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
> creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
> USB2PHY is connected to ocp2scp.
> 
> This also includes device tree support for ocp2scp driver and
> the documentation with device tree binding information is updated.
> 
> Cc: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>

If you fix (or change my mind) on the comment below, you can add:

Acked-by: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>


Also, I wonder who should be the one to take this. Who will be queueing
patches on this directory to mainline ?

> Acked-by: Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
> Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
> ---
>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
>  drivers/Kconfig                                    |    2 +
>  drivers/Makefile                                   |    2 +
>  drivers/bus/Kconfig                                |   15 +++
>  drivers/bus/Makefile                               |    5 +
>  drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
>  6 files changed, 132 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>  create mode 100644 drivers/bus/Kconfig
>  create mode 100644 drivers/bus/Makefile
>  create mode 100644 drivers/bus/omap-ocp2scp.c
> 
> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> new file mode 100644
> index 0000000..d2fe064
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> @@ -0,0 +1,10 @@
> +* OMAP OCP2SCP - ocp interface to scp interface
> +
> +properties:
> +- compatible : Should be "ti,omap-ocp2scp"
> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
> +- ranges : the child address space are mapped 1:1 onto the parent address space
> +- ti,hwmods : must be "ocp2scp_usb_phy"
> +
> +Sub-nodes:
> +All the devices connected to ocp2scp are described using sub-node to ocp2scp
> diff --git a/drivers/Kconfig b/drivers/Kconfig
> index bfc9186..4fe1e4c 100644
> --- a/drivers/Kconfig
> +++ b/drivers/Kconfig
> @@ -2,6 +2,8 @@ menu "Device Drivers"
>  
>  source "drivers/base/Kconfig"
>  
> +source "drivers/bus/Kconfig"
> +
>  source "drivers/connector/Kconfig"
>  
>  source "drivers/mtd/Kconfig"
> diff --git a/drivers/Makefile b/drivers/Makefile
> index 2ba29ff..cac3819 100644
> --- a/drivers/Makefile
> +++ b/drivers/Makefile
> @@ -5,6 +5,8 @@
>  # Rewritten to use lists instead of if-statements.
>  #
>  
> +obj-y				+= bus/
> +
>  # GPIO must come after pinctrl as gpios may need to mux pins etc
>  obj-y				+= pinctrl/
>  obj-y				+= gpio/
> diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
> new file mode 100644
> index 0000000..6270415
> --- /dev/null
> +++ b/drivers/bus/Kconfig
> @@ -0,0 +1,15 @@
> +#
> +# Bus Devices
> +#
> +
> +menu "Bus devices"
> +
> +config OMAP_OCP2SCP
> +	tristate "OMAP OCP2SCP DRIVER"
> +	help
> +	  Driver to enable ocp2scp module which transforms ocp interface
> +	  protocol to scp protocol. In OMAP4, USB PHY is connected via
> +	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
> +	  OCP2SCP.
> +
> +endmenu
> diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
> new file mode 100644
> index 0000000..0ec50bc
> --- /dev/null
> +++ b/drivers/bus/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for the bus drivers.
> +#
> +
> +obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
> diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
> new file mode 100644
> index 0000000..8c3db3a
> --- /dev/null
> +++ b/drivers/bus/omap-ocp2scp.c
> @@ -0,0 +1,98 @@
> +/*
> + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
> + *
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Author: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/err.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +
> +static int ocp2scp_remove_devices(struct device *dev, void *c)
> +{
> +	struct platform_device *pdev = to_platform_device(dev);
> +
> +	platform_device_unregister(pdev);
> +
> +	return 0;
> +}
> +
> +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
> +{
> +	int			ret;
> +	struct device_node	*np = pdev->dev.of_node;
> +
> +	if (np) {
> +		ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
> +		if (ret) {
> +			dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
> +			goto err0;
> +		}
> +	}
> +	pm_runtime_enable(&pdev->dev);
> +
> +	return 0;
> +
> +err0:
> +	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
> +
> +	return ret;
> +}
> +
> +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
> +{
> +	pm_runtime_disable(&pdev->dev);
> +	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id omap_ocp2scp_id_table[] = {
> +	{ .compatible = "ti,omap-ocp2scp" },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
> +#endif
> +
> +static struct platform_driver omap_ocp2scp_driver = {
> +	.probe		= omap_ocp2scp_probe,
> +	.remove		= __devexit_p(omap_ocp2scp_remove),
> +	.driver		= {
> +		.name	= "omap-ocp2scp",
> +		.owner	= THIS_MODULE,
> +		.of_match_table = of_match_ptr(omap_ocp2scp_id_table),
> +	},
> +};
> +
> +static int __init omap_ocp2scp_init(void)
> +{
> +	return platform_driver_register(&omap_ocp2scp_driver);
> +}
> +arch_initcall(omap_ocp2scp_init);

I really think we should avoid this trickery and make dependent drivers
return -EPROBE_DEFER case this isn't ready yet.

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[Felipe Balbi]

Hi,

On Wed, Jul 18, 2012 at 12:00:38PM +0530, Kishon Vijay Abraham I wrote:
> Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
> creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
> USB2PHY is connected to ocp2scp.
> 
> This also includes device tree support for ocp2scp driver and
> the documentation with device tree binding information is updated.
> 
> Cc: Felipe Balbi <balbi@ti.com>

If you fix (or change my mind) on the comment below, you can add:

Acked-by: Felipe Balbi <balbi@ti.com>


Also, I wonder who should be the one to take this. Who will be queueing
patches on this directory to mainline ?

> Acked-by: Arnd Bergmann <arnd@arndb.de>
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
>  drivers/Kconfig                                    |    2 +
>  drivers/Makefile                                   |    2 +
>  drivers/bus/Kconfig                                |   15 +++
>  drivers/bus/Makefile                               |    5 +
>  drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
>  6 files changed, 132 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>  create mode 100644 drivers/bus/Kconfig
>  create mode 100644 drivers/bus/Makefile
>  create mode 100644 drivers/bus/omap-ocp2scp.c
> 
> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> new file mode 100644
> index 0000000..d2fe064
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
> @@ -0,0 +1,10 @@
> +* OMAP OCP2SCP - ocp interface to scp interface
> +
> +properties:
> +- compatible : Should be "ti,omap-ocp2scp"
> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
> +- ranges : the child address space are mapped 1:1 onto the parent address space
> +- ti,hwmods : must be "ocp2scp_usb_phy"
> +
> +Sub-nodes:
> +All the devices connected to ocp2scp are described using sub-node to ocp2scp
> diff --git a/drivers/Kconfig b/drivers/Kconfig
> index bfc9186..4fe1e4c 100644
> --- a/drivers/Kconfig
> +++ b/drivers/Kconfig
> @@ -2,6 +2,8 @@ menu "Device Drivers"
>  
>  source "drivers/base/Kconfig"
>  
> +source "drivers/bus/Kconfig"
> +
>  source "drivers/connector/Kconfig"
>  
>  source "drivers/mtd/Kconfig"
> diff --git a/drivers/Makefile b/drivers/Makefile
> index 2ba29ff..cac3819 100644
> --- a/drivers/Makefile
> +++ b/drivers/Makefile
> @@ -5,6 +5,8 @@
>  # Rewritten to use lists instead of if-statements.
>  #
>  
> +obj-y				+= bus/
> +
>  # GPIO must come after pinctrl as gpios may need to mux pins etc
>  obj-y				+= pinctrl/
>  obj-y				+= gpio/
> diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
> new file mode 100644
> index 0000000..6270415
> --- /dev/null
> +++ b/drivers/bus/Kconfig
> @@ -0,0 +1,15 @@
> +#
> +# Bus Devices
> +#
> +
> +menu "Bus devices"
> +
> +config OMAP_OCP2SCP
> +	tristate "OMAP OCP2SCP DRIVER"
> +	help
> +	  Driver to enable ocp2scp module which transforms ocp interface
> +	  protocol to scp protocol. In OMAP4, USB PHY is connected via
> +	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
> +	  OCP2SCP.
> +
> +endmenu
> diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
> new file mode 100644
> index 0000000..0ec50bc
> --- /dev/null
> +++ b/drivers/bus/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for the bus drivers.
> +#
> +
> +obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
> diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
> new file mode 100644
> index 0000000..8c3db3a
> --- /dev/null
> +++ b/drivers/bus/omap-ocp2scp.c
> @@ -0,0 +1,98 @@
> +/*
> + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
> + *
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Author: Kishon Vijay Abraham I <kishon@ti.com>
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/err.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +
> +static int ocp2scp_remove_devices(struct device *dev, void *c)
> +{
> +	struct platform_device *pdev = to_platform_device(dev);
> +
> +	platform_device_unregister(pdev);
> +
> +	return 0;
> +}
> +
> +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
> +{
> +	int			ret;
> +	struct device_node	*np = pdev->dev.of_node;
> +
> +	if (np) {
> +		ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
> +		if (ret) {
> +			dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
> +			goto err0;
> +		}
> +	}
> +	pm_runtime_enable(&pdev->dev);
> +
> +	return 0;
> +
> +err0:
> +	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
> +
> +	return ret;
> +}
> +
> +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
> +{
> +	pm_runtime_disable(&pdev->dev);
> +	device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id omap_ocp2scp_id_table[] = {
> +	{ .compatible = "ti,omap-ocp2scp" },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
> +#endif
> +
> +static struct platform_driver omap_ocp2scp_driver = {
> +	.probe		= omap_ocp2scp_probe,
> +	.remove		= __devexit_p(omap_ocp2scp_remove),
> +	.driver		= {
> +		.name	= "omap-ocp2scp",
> +		.owner	= THIS_MODULE,
> +		.of_match_table = of_match_ptr(omap_ocp2scp_id_table),
> +	},
> +};
> +
> +static int __init omap_ocp2scp_init(void)
> +{
> +	return platform_driver_register(&omap_ocp2scp_driver);
> +}
> +arch_initcall(omap_ocp2scp_init);

I really think we should avoid this trickery and make dependent drivers
return -EPROBE_DEFER case this isn't ready yet.

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120803/26e59782/attachment.sig>

Re: [PATCH v2 2/2] arm/dts: omap4: Add ocp2scp data

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 846 bytes --]

On Wed, Jul 18, 2012 at 12:00:39PM +0530, Kishon Vijay Abraham I wrote:
> Add ocp2scp data node in omap4 device tree file.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Acked-by: Felipe Balbi <balbi@ti.com>

> ---
>  arch/arm/boot/dts/omap4.dtsi |    8 ++++++++
>  1 files changed, 8 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
> index 359c497..29c6243 100644
> --- a/arch/arm/boot/dts/omap4.dtsi
> +++ b/arch/arm/boot/dts/omap4.dtsi
> @@ -272,5 +272,13 @@
>  			ti,hwmods = "mmc5";
>  			ti,needs-special-reset;
>  		};
> +
> +		ocp2scp {
> +			compatible = "ti,omap-ocp2scp";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			ti,hwmods = "ocp2scp_usb_phy";
> +		};
>  	};
>  };
> -- 
> 1.7.5.4
> 

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH v2 2/2] arm/dts: omap4: Add ocp2scp data

[Felipe Balbi]

On Wed, Jul 18, 2012 at 12:00:39PM +0530, Kishon Vijay Abraham I wrote:
> Add ocp2scp data node in omap4 device tree file.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Acked-by: Felipe Balbi <balbi@ti.com>

> ---
>  arch/arm/boot/dts/omap4.dtsi |    8 ++++++++
>  1 files changed, 8 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
> index 359c497..29c6243 100644
> --- a/arch/arm/boot/dts/omap4.dtsi
> +++ b/arch/arm/boot/dts/omap4.dtsi
> @@ -272,5 +272,13 @@
>  			ti,hwmods = "mmc5";
>  			ti,needs-special-reset;
>  		};
> +
> +		ocp2scp {
> +			compatible = "ti,omap-ocp2scp";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			ti,hwmods = "ocp2scp_usb_phy";
> +		};
>  	};
>  };
> -- 
> 1.7.5.4
> 

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120803/3356c810/attachment.sig>

Re: [PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[ABRAHAM, KISHON VIJAY]

Hi,

On Fri, Aug 3, 2012 at 6:50 PM, Felipe Balbi <balbi@ti.com> wrote:
> Hi,
>
> On Wed, Jul 18, 2012 at 12:00:38PM +0530, Kishon Vijay Abraham I wrote:
>> Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
>> creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
>> USB2PHY is connected to ocp2scp.
>>
>> This also includes device tree support for ocp2scp driver and
>> the documentation with device tree binding information is updated.
>>
>> Cc: Felipe Balbi <balbi@ti.com>
>
> If you fix (or change my mind) on the comment below, you can add:
>
> Acked-by: Felipe Balbi <balbi@ti.com>
>
>
> Also, I wonder who should be the one to take this. Who will be queueing
> patches on this directory to mainline ?
>
>> Acked-by: Arnd Bergmann <arnd@arndb.de>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>> ---
>>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
>>  drivers/Kconfig                                    |    2 +
>>  drivers/Makefile                                   |    2 +
>>  drivers/bus/Kconfig                                |   15 +++
>>  drivers/bus/Makefile                               |    5 +
>>  drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
>>  6 files changed, 132 insertions(+), 0 deletions(-)
>>  create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>>  create mode 100644 drivers/bus/Kconfig
>>  create mode 100644 drivers/bus/Makefile
>>  create mode 100644 drivers/bus/omap-ocp2scp.c
>>
>> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>> new file mode 100644
>> index 0000000..d2fe064
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>> @@ -0,0 +1,10 @@
>> +* OMAP OCP2SCP - ocp interface to scp interface
>> +
>> +properties:
>> +- compatible : Should be "ti,omap-ocp2scp"
>> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
>> +- ranges : the child address space are mapped 1:1 onto the parent address space
>> +- ti,hwmods : must be "ocp2scp_usb_phy"
>> +
>> +Sub-nodes:
>> +All the devices connected to ocp2scp are described using sub-node to ocp2scp
>> diff --git a/drivers/Kconfig b/drivers/Kconfig
>> index bfc9186..4fe1e4c 100644
>> --- a/drivers/Kconfig
>> +++ b/drivers/Kconfig
>> @@ -2,6 +2,8 @@ menu "Device Drivers"
>>
>>  source "drivers/base/Kconfig"
>>
>> +source "drivers/bus/Kconfig"
>> +
>>  source "drivers/connector/Kconfig"
>>
>>  source "drivers/mtd/Kconfig"
>> diff --git a/drivers/Makefile b/drivers/Makefile
>> index 2ba29ff..cac3819 100644
>> --- a/drivers/Makefile
>> +++ b/drivers/Makefile
>> @@ -5,6 +5,8 @@
>>  # Rewritten to use lists instead of if-statements.
>>  #
>>
>> +obj-y                                += bus/
>> +
>>  # GPIO must come after pinctrl as gpios may need to mux pins etc
>>  obj-y                                += pinctrl/
>>  obj-y                                += gpio/
>> diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
>> new file mode 100644
>> index 0000000..6270415
>> --- /dev/null
>> +++ b/drivers/bus/Kconfig
>> @@ -0,0 +1,15 @@
>> +#
>> +# Bus Devices
>> +#
>> +
>> +menu "Bus devices"
>> +
>> +config OMAP_OCP2SCP
>> +     tristate "OMAP OCP2SCP DRIVER"
>> +     help
>> +       Driver to enable ocp2scp module which transforms ocp interface
>> +       protocol to scp protocol. In OMAP4, USB PHY is connected via
>> +       OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
>> +       OCP2SCP.
>> +
>> +endmenu
>> diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
>> new file mode 100644
>> index 0000000..0ec50bc
>> --- /dev/null
>> +++ b/drivers/bus/Makefile
>> @@ -0,0 +1,5 @@
>> +#
>> +# Makefile for the bus drivers.
>> +#
>> +
>> +obj-$(CONFIG_OMAP_OCP2SCP)   += omap-ocp2scp.o
>> diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
>> new file mode 100644
>> index 0000000..8c3db3a
>> --- /dev/null
>> +++ b/drivers/bus/omap-ocp2scp.c
>> @@ -0,0 +1,98 @@
>> +/*
>> + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
>> + *
>> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * Author: Kishon Vijay Abraham I <kishon@ti.com>
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/err.h>
>> +#include <linux/pm_runtime.h>
>> +#include <linux/of.h>
>> +#include <linux/of_platform.h>
>> +
>> +static int ocp2scp_remove_devices(struct device *dev, void *c)
>> +{
>> +     struct platform_device *pdev = to_platform_device(dev);
>> +
>> +     platform_device_unregister(pdev);
>> +
>> +     return 0;
>> +}
>> +
>> +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
>> +{
>> +     int                     ret;
>> +     struct device_node      *np = pdev->dev.of_node;
>> +
>> +     if (np) {
>> +             ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
>> +             if (ret) {
>> +                     dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
>> +                     goto err0;
>> +             }
>> +     }
>> +     pm_runtime_enable(&pdev->dev);
>> +
>> +     return 0;
>> +
>> +err0:
>> +     device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
>> +
>> +     return ret;
>> +}
>> +
>> +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
>> +{
>> +     pm_runtime_disable(&pdev->dev);
>> +     device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
>> +
>> +     return 0;
>> +}
>> +
>> +#ifdef CONFIG_OF
>> +static const struct of_device_id omap_ocp2scp_id_table[] = {
>> +     { .compatible = "ti,omap-ocp2scp" },
>> +     {}
>> +};
>> +MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
>> +#endif
>> +
>> +static struct platform_driver omap_ocp2scp_driver = {
>> +     .probe          = omap_ocp2scp_probe,
>> +     .remove         = __devexit_p(omap_ocp2scp_remove),
>> +     .driver         = {
>> +             .name   = "omap-ocp2scp",
>> +             .owner  = THIS_MODULE,
>> +             .of_match_table = of_match_ptr(omap_ocp2scp_id_table),
>> +     },
>> +};
>> +
>> +static int __init omap_ocp2scp_init(void)
>> +{
>> +     return platform_driver_register(&omap_ocp2scp_driver);
>> +}
>> +arch_initcall(omap_ocp2scp_init);
>
> I really think we should avoid this trickery and make dependent drivers
> return -EPROBE_DEFER case this isn't ready yet.

Ok. Will do it that way in my next series.

Thanks
Kishon

Re: [PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[ABRAHAM, KISHON VIJAY]

Hi,

On Fri, Aug 3, 2012 at 6:50 PM, Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org> wrote:
> Hi,
>
> On Wed, Jul 18, 2012 at 12:00:38PM +0530, Kishon Vijay Abraham I wrote:
>> Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
>> creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
>> USB2PHY is connected to ocp2scp.
>>
>> This also includes device tree support for ocp2scp driver and
>> the documentation with device tree binding information is updated.
>>
>> Cc: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>
>
> If you fix (or change my mind) on the comment below, you can add:
>
> Acked-by: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>
>
>
> Also, I wonder who should be the one to take this. Who will be queueing
> patches on this directory to mainline ?
>
>> Acked-by: Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
>> Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
>> ---
>>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
>>  drivers/Kconfig                                    |    2 +
>>  drivers/Makefile                                   |    2 +
>>  drivers/bus/Kconfig                                |   15 +++
>>  drivers/bus/Makefile                               |    5 +
>>  drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
>>  6 files changed, 132 insertions(+), 0 deletions(-)
>>  create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>>  create mode 100644 drivers/bus/Kconfig
>>  create mode 100644 drivers/bus/Makefile
>>  create mode 100644 drivers/bus/omap-ocp2scp.c
>>
>> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>> new file mode 100644
>> index 0000000..d2fe064
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>> @@ -0,0 +1,10 @@
>> +* OMAP OCP2SCP - ocp interface to scp interface
>> +
>> +properties:
>> +- compatible : Should be "ti,omap-ocp2scp"
>> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
>> +- ranges : the child address space are mapped 1:1 onto the parent address space
>> +- ti,hwmods : must be "ocp2scp_usb_phy"
>> +
>> +Sub-nodes:
>> +All the devices connected to ocp2scp are described using sub-node to ocp2scp
>> diff --git a/drivers/Kconfig b/drivers/Kconfig
>> index bfc9186..4fe1e4c 100644
>> --- a/drivers/Kconfig
>> +++ b/drivers/Kconfig
>> @@ -2,6 +2,8 @@ menu "Device Drivers"
>>
>>  source "drivers/base/Kconfig"
>>
>> +source "drivers/bus/Kconfig"
>> +
>>  source "drivers/connector/Kconfig"
>>
>>  source "drivers/mtd/Kconfig"
>> diff --git a/drivers/Makefile b/drivers/Makefile
>> index 2ba29ff..cac3819 100644
>> --- a/drivers/Makefile
>> +++ b/drivers/Makefile
>> @@ -5,6 +5,8 @@
>>  # Rewritten to use lists instead of if-statements.
>>  #
>>
>> +obj-y                                += bus/
>> +
>>  # GPIO must come after pinctrl as gpios may need to mux pins etc
>>  obj-y                                += pinctrl/
>>  obj-y                                += gpio/
>> diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
>> new file mode 100644
>> index 0000000..6270415
>> --- /dev/null
>> +++ b/drivers/bus/Kconfig
>> @@ -0,0 +1,15 @@
>> +#
>> +# Bus Devices
>> +#
>> +
>> +menu "Bus devices"
>> +
>> +config OMAP_OCP2SCP
>> +     tristate "OMAP OCP2SCP DRIVER"
>> +     help
>> +       Driver to enable ocp2scp module which transforms ocp interface
>> +       protocol to scp protocol. In OMAP4, USB PHY is connected via
>> +       OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
>> +       OCP2SCP.
>> +
>> +endmenu
>> diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
>> new file mode 100644
>> index 0000000..0ec50bc
>> --- /dev/null
>> +++ b/drivers/bus/Makefile
>> @@ -0,0 +1,5 @@
>> +#
>> +# Makefile for the bus drivers.
>> +#
>> +
>> +obj-$(CONFIG_OMAP_OCP2SCP)   += omap-ocp2scp.o
>> diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
>> new file mode 100644
>> index 0000000..8c3db3a
>> --- /dev/null
>> +++ b/drivers/bus/omap-ocp2scp.c
>> @@ -0,0 +1,98 @@
>> +/*
>> + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
>> + *
>> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * Author: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/err.h>
>> +#include <linux/pm_runtime.h>
>> +#include <linux/of.h>
>> +#include <linux/of_platform.h>
>> +
>> +static int ocp2scp_remove_devices(struct device *dev, void *c)
>> +{
>> +     struct platform_device *pdev = to_platform_device(dev);
>> +
>> +     platform_device_unregister(pdev);
>> +
>> +     return 0;
>> +}
>> +
>> +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
>> +{
>> +     int                     ret;
>> +     struct device_node      *np = pdev->dev.of_node;
>> +
>> +     if (np) {
>> +             ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
>> +             if (ret) {
>> +                     dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
>> +                     goto err0;
>> +             }
>> +     }
>> +     pm_runtime_enable(&pdev->dev);
>> +
>> +     return 0;
>> +
>> +err0:
>> +     device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
>> +
>> +     return ret;
>> +}
>> +
>> +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
>> +{
>> +     pm_runtime_disable(&pdev->dev);
>> +     device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
>> +
>> +     return 0;
>> +}
>> +
>> +#ifdef CONFIG_OF
>> +static const struct of_device_id omap_ocp2scp_id_table[] = {
>> +     { .compatible = "ti,omap-ocp2scp" },
>> +     {}
>> +};
>> +MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
>> +#endif
>> +
>> +static struct platform_driver omap_ocp2scp_driver = {
>> +     .probe          = omap_ocp2scp_probe,
>> +     .remove         = __devexit_p(omap_ocp2scp_remove),
>> +     .driver         = {
>> +             .name   = "omap-ocp2scp",
>> +             .owner  = THIS_MODULE,
>> +             .of_match_table = of_match_ptr(omap_ocp2scp_id_table),
>> +     },
>> +};
>> +
>> +static int __init omap_ocp2scp_init(void)
>> +{
>> +     return platform_driver_register(&omap_ocp2scp_driver);
>> +}
>> +arch_initcall(omap_ocp2scp_init);
>
> I really think we should avoid this trickery and make dependent drivers
> return -EPROBE_DEFER case this isn't ready yet.

Ok. Will do it that way in my next series.

Thanks
Kishon

[PATCH v2 1/2] drivers: bus: add a new driver for omap-ocp2scp

[ABRAHAM, KISHON VIJAY]

Hi,

On Fri, Aug 3, 2012 at 6:50 PM, Felipe Balbi <balbi@ti.com> wrote:
> Hi,
>
> On Wed, Jul 18, 2012 at 12:00:38PM +0530, Kishon Vijay Abraham I wrote:
>> Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
>> creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
>> USB2PHY is connected to ocp2scp.
>>
>> This also includes device tree support for ocp2scp driver and
>> the documentation with device tree binding information is updated.
>>
>> Cc: Felipe Balbi <balbi@ti.com>
>
> If you fix (or change my mind) on the comment below, you can add:
>
> Acked-by: Felipe Balbi <balbi@ti.com>
>
>
> Also, I wonder who should be the one to take this. Who will be queueing
> patches on this directory to mainline ?
>
>> Acked-by: Arnd Bergmann <arnd@arndb.de>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>> ---
>>  .../devicetree/bindings/bus/omap-ocp2scp.txt       |   10 ++
>>  drivers/Kconfig                                    |    2 +
>>  drivers/Makefile                                   |    2 +
>>  drivers/bus/Kconfig                                |   15 +++
>>  drivers/bus/Makefile                               |    5 +
>>  drivers/bus/omap-ocp2scp.c                         |   98 ++++++++++++++++++++
>>  6 files changed, 132 insertions(+), 0 deletions(-)
>>  create mode 100644 Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>>  create mode 100644 drivers/bus/Kconfig
>>  create mode 100644 drivers/bus/Makefile
>>  create mode 100644 drivers/bus/omap-ocp2scp.c
>>
>> diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>> new file mode 100644
>> index 0000000..d2fe064
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
>> @@ -0,0 +1,10 @@
>> +* OMAP OCP2SCP - ocp interface to scp interface
>> +
>> +properties:
>> +- compatible : Should be "ti,omap-ocp2scp"
>> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
>> +- ranges : the child address space are mapped 1:1 onto the parent address space
>> +- ti,hwmods : must be "ocp2scp_usb_phy"
>> +
>> +Sub-nodes:
>> +All the devices connected to ocp2scp are described using sub-node to ocp2scp
>> diff --git a/drivers/Kconfig b/drivers/Kconfig
>> index bfc9186..4fe1e4c 100644
>> --- a/drivers/Kconfig
>> +++ b/drivers/Kconfig
>> @@ -2,6 +2,8 @@ menu "Device Drivers"
>>
>>  source "drivers/base/Kconfig"
>>
>> +source "drivers/bus/Kconfig"
>> +
>>  source "drivers/connector/Kconfig"
>>
>>  source "drivers/mtd/Kconfig"
>> diff --git a/drivers/Makefile b/drivers/Makefile
>> index 2ba29ff..cac3819 100644
>> --- a/drivers/Makefile
>> +++ b/drivers/Makefile
>> @@ -5,6 +5,8 @@
>>  # Rewritten to use lists instead of if-statements.
>>  #
>>
>> +obj-y                                += bus/
>> +
>>  # GPIO must come after pinctrl as gpios may need to mux pins etc
>>  obj-y                                += pinctrl/
>>  obj-y                                += gpio/
>> diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
>> new file mode 100644
>> index 0000000..6270415
>> --- /dev/null
>> +++ b/drivers/bus/Kconfig
>> @@ -0,0 +1,15 @@
>> +#
>> +# Bus Devices
>> +#
>> +
>> +menu "Bus devices"
>> +
>> +config OMAP_OCP2SCP
>> +     tristate "OMAP OCP2SCP DRIVER"
>> +     help
>> +       Driver to enable ocp2scp module which transforms ocp interface
>> +       protocol to scp protocol. In OMAP4, USB PHY is connected via
>> +       OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
>> +       OCP2SCP.
>> +
>> +endmenu
>> diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
>> new file mode 100644
>> index 0000000..0ec50bc
>> --- /dev/null
>> +++ b/drivers/bus/Makefile
>> @@ -0,0 +1,5 @@
>> +#
>> +# Makefile for the bus drivers.
>> +#
>> +
>> +obj-$(CONFIG_OMAP_OCP2SCP)   += omap-ocp2scp.o
>> diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
>> new file mode 100644
>> index 0000000..8c3db3a
>> --- /dev/null
>> +++ b/drivers/bus/omap-ocp2scp.c
>> @@ -0,0 +1,98 @@
>> +/*
>> + * omap-ocp2scp.c - transform ocp interface protocol to scp protocol
>> + *
>> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * Author: Kishon Vijay Abraham I <kishon@ti.com>
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/err.h>
>> +#include <linux/pm_runtime.h>
>> +#include <linux/of.h>
>> +#include <linux/of_platform.h>
>> +
>> +static int ocp2scp_remove_devices(struct device *dev, void *c)
>> +{
>> +     struct platform_device *pdev = to_platform_device(dev);
>> +
>> +     platform_device_unregister(pdev);
>> +
>> +     return 0;
>> +}
>> +
>> +static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
>> +{
>> +     int                     ret;
>> +     struct device_node      *np = pdev->dev.of_node;
>> +
>> +     if (np) {
>> +             ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
>> +             if (ret) {
>> +                     dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
>> +                     goto err0;
>> +             }
>> +     }
>> +     pm_runtime_enable(&pdev->dev);
>> +
>> +     return 0;
>> +
>> +err0:
>> +     device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
>> +
>> +     return ret;
>> +}
>> +
>> +static int __devexit omap_ocp2scp_remove(struct platform_device *pdev)
>> +{
>> +     pm_runtime_disable(&pdev->dev);
>> +     device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
>> +
>> +     return 0;
>> +}
>> +
>> +#ifdef CONFIG_OF
>> +static const struct of_device_id omap_ocp2scp_id_table[] = {
>> +     { .compatible = "ti,omap-ocp2scp" },
>> +     {}
>> +};
>> +MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
>> +#endif
>> +
>> +static struct platform_driver omap_ocp2scp_driver = {
>> +     .probe          = omap_ocp2scp_probe,
>> +     .remove         = __devexit_p(omap_ocp2scp_remove),
>> +     .driver         = {
>> +             .name   = "omap-ocp2scp",
>> +             .owner  = THIS_MODULE,
>> +             .of_match_table = of_match_ptr(omap_ocp2scp_id_table),
>> +     },
>> +};
>> +
>> +static int __init omap_ocp2scp_init(void)
>> +{
>> +     return platform_driver_register(&omap_ocp2scp_driver);
>> +}
>> +arch_initcall(omap_ocp2scp_init);
>
> I really think we should avoid this trickery and make dependent drivers
> return -EPROBE_DEFER case this isn't ready yet.

Ok. Will do it that way in my next series.

Thanks
Kishon