* [PATCH v5 0/4] Support for TSC/ADC MFD driver
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
This patch set adds a MFD core driver which registers
touchscreen and ADC as its client drivers.
The existing touchscreen has been modified to work as
a MFD client driver and a new ADC driver has been added
in the IIO subsystem.
There are 8 analog input lines, which can be used as:
1. 8 general purpose ADC channels
2. 4 wire TS, with 4 general purpose ADC channels
3. 5 wire TS, with 3 general purpose ADC channels
This patch set has been tested on AM335x EVM.
These set of patches apply to linux-nxt branch and are based
on top of Touchscreen patch set submitted viz.
Subject: [PATCH 0/4] input: TSC: ti_tscadc: TI Touchscreen driver updates [1]
[1] http://www.spinics.net/lists/linux-input/msg22107.html
Changes in v2:
Dropped one patch send in the last version after
receiving internal comments. I have merged the changes
into existing patches.
Also added a new patch to support suspend/resume feature.
Fixed review comments by Matthias Kaehlcke.
Changes in v3:
Addressed review comments by Jonathan Cameron.
Improved ADC driver with more readable labels,
spaces and comments.
Changes in v4:
Renamed the drivers from ti_xxx to ti_am335x_xxx.
For consistency with other drivers renamed idev to indio_dev
in IIO ADC driver.
Replaced suspend/resume callbacks with dev_pm_ops.
Changes in v5:
Merged suspend/resume part of code (present as separate patch)
into the respective driver.
Patil, Rachna (4):
input: TSC: ti_tscadc: Rename the existing touchscreen driver
MFD: ti_tscadc: Add support for TI's TSC/ADC MFDevice
input: TSC: ti_tsc: Convert TSC into a MFDevice
IIO : ADC: tiadc: Add support of TI's ADC driver
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/ti_am335x_adc.c | 260 ++++++++++
drivers/input/touchscreen/Kconfig | 6 +-
drivers/input/touchscreen/Makefile | 2 +-
drivers/input/touchscreen/ti_am335x_tsc.c | 398 +++++++++++++++
drivers/input/touchscreen/ti_tscadc.c | 522 --------------------
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/ti_am335x_tscadc.c | 277 +++++++++++
.../linux/input/{ti_tscadc.h => ti_am335x_tsc.h} | 4 +-
include/linux/mfd/ti_am335x_tscadc.h | 152 ++++++
include/linux/platform_data/ti_am335x_adc.h | 14 +
13 files changed, 1127 insertions(+), 528 deletions(-)
create mode 100644 drivers/iio/adc/ti_am335x_adc.c
create mode 100644 drivers/input/touchscreen/ti_am335x_tsc.c
delete mode 100644 drivers/input/touchscreen/ti_tscadc.c
create mode 100644 drivers/mfd/ti_am335x_tscadc.c
rename include/linux/input/{ti_tscadc.h => ti_am335x_tsc.h} (88%)
create mode 100644 include/linux/mfd/ti_am335x_tscadc.h
create mode 100644 include/linux/platform_data/ti_am335x_adc.h
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v5 0/4] Support for TSC/ADC MFD driver
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
This patch set adds a MFD core driver which registers
touchscreen and ADC as its client drivers.
The existing touchscreen has been modified to work as
a MFD client driver and a new ADC driver has been added
in the IIO subsystem.
There are 8 analog input lines, which can be used as:
1. 8 general purpose ADC channels
2. 4 wire TS, with 4 general purpose ADC channels
3. 5 wire TS, with 3 general purpose ADC channels
This patch set has been tested on AM335x EVM.
These set of patches apply to linux-nxt branch and are based
on top of Touchscreen patch set submitted viz.
Subject: [PATCH 0/4] input: TSC: ti_tscadc: TI Touchscreen driver updates [1]
[1] http://www.spinics.net/lists/linux-input/msg22107.html
Changes in v2:
Dropped one patch send in the last version after
receiving internal comments. I have merged the changes
into existing patches.
Also added a new patch to support suspend/resume feature.
Fixed review comments by Matthias Kaehlcke.
Changes in v3:
Addressed review comments by Jonathan Cameron.
Improved ADC driver with more readable labels,
spaces and comments.
Changes in v4:
Renamed the drivers from ti_xxx to ti_am335x_xxx.
For consistency with other drivers renamed idev to indio_dev
in IIO ADC driver.
Replaced suspend/resume callbacks with dev_pm_ops.
Changes in v5:
Merged suspend/resume part of code (present as separate patch)
into the respective driver.
Patil, Rachna (4):
input: TSC: ti_tscadc: Rename the existing touchscreen driver
MFD: ti_tscadc: Add support for TI's TSC/ADC MFDevice
input: TSC: ti_tsc: Convert TSC into a MFDevice
IIO : ADC: tiadc: Add support of TI's ADC driver
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/ti_am335x_adc.c | 260 ++++++++++
drivers/input/touchscreen/Kconfig | 6 +-
drivers/input/touchscreen/Makefile | 2 +-
drivers/input/touchscreen/ti_am335x_tsc.c | 398 +++++++++++++++
drivers/input/touchscreen/ti_tscadc.c | 522 --------------------
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/ti_am335x_tscadc.c | 277 +++++++++++
.../linux/input/{ti_tscadc.h => ti_am335x_tsc.h} | 4 +-
include/linux/mfd/ti_am335x_tscadc.h | 152 ++++++
include/linux/platform_data/ti_am335x_adc.h | 14 +
13 files changed, 1127 insertions(+), 528 deletions(-)
create mode 100644 drivers/iio/adc/ti_am335x_adc.c
create mode 100644 drivers/input/touchscreen/ti_am335x_tsc.c
delete mode 100644 drivers/input/touchscreen/ti_tscadc.c
create mode 100644 drivers/mfd/ti_am335x_tscadc.c
rename include/linux/input/{ti_tscadc.h => ti_am335x_tsc.h} (88%)
create mode 100644 include/linux/mfd/ti_am335x_tscadc.h
create mode 100644 include/linux/platform_data/ti_am335x_adc.h
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v5 1/4] input: TSC: ti_tscadc: Rename the existing touchscreen driver
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
Make way for addition of MFD driver.
The existing touchsreen driver is a MFD client.
For better readability we rename the file to
indicate its functionality as only touchscreen.
Signed-off-by: Patil, Rachna <rachna@ti.com>
---
Changes in v2:
Missed changing the name of touchscreen header file
in the previous version.
Adding the same.
Changes in v3:
no changes.
Changes in v4:
no changes.
Changes in v5:
updated the struct and function names to match
that of file name for better readability.
drivers/input/touchscreen/Kconfig | 4 +-
drivers/input/touchscreen/Makefile | 2 +-
.../touchscreen/{ti_tscadc.c => ti_am335x_tsc.c} | 96 ++++++++++----------
.../linux/input/{ti_tscadc.h => ti_am335x_tsc.h} | 4 +-
4 files changed, 53 insertions(+), 53 deletions(-)
rename drivers/input/touchscreen/{ti_tscadc.c => ti_am335x_tsc.c} (83%)
rename include/linux/input/{ti_tscadc.h => ti_am335x_tsc.h} (88%)
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 1ba232c..7bdb629 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -529,7 +529,7 @@ config TOUCHSCREEN_TOUCHWIN
To compile this driver as a module, choose M here: the
module will be called touchwin.
-config TOUCHSCREEN_TI_TSCADC
+config TOUCHSCREEN_TI_AM335X_TSC
tristate "TI Touchscreen Interface"
depends on ARCH_OMAP2PLUS
help
@@ -539,7 +539,7 @@ config TOUCHSCREEN_TI_TSCADC
If unsure, say N.
To compile this driver as a module, choose M here: the
- module will be called ti_tscadc.
+ module will be called ti_am335x_tsc.
config TOUCHSCREEN_ATMEL_TSADCC
tristate "Atmel Touchscreen Interface"
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 178eb12..7c4c78e 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -52,7 +52,7 @@ obj-$(CONFIG_TOUCHSCREEN_PIXCIR) += pixcir_i2c_ts.o
obj-$(CONFIG_TOUCHSCREEN_S3C2410) += s3c2410_ts.o
obj-$(CONFIG_TOUCHSCREEN_ST1232) += st1232.o
obj-$(CONFIG_TOUCHSCREEN_STMPE) += stmpe-ts.o
-obj-$(CONFIG_TOUCHSCREEN_TI_TSCADC) += ti_tscadc.o
+obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
obj-$(CONFIG_TOUCHSCREEN_TNETV107X) += tnetv107x-ts.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
diff --git a/drivers/input/touchscreen/ti_tscadc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
similarity index 83%
rename from drivers/input/touchscreen/ti_tscadc.c
rename to drivers/input/touchscreen/ti_am335x_tsc.c
index ec0a442..462950a 100644
--- a/drivers/input/touchscreen/ti_tscadc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -24,7 +24,7 @@
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <linux/input/ti_tscadc.h>
+#include <linux/input/ti_am335x_tsc.h>
#include <linux/delay.h>
#define REG_RAWIRQSTATUS 0x024
@@ -123,7 +123,7 @@
#define ADC_CLK 3000000
#define MAX_12BIT ((1 << 12) - 1)
-struct tscadc {
+struct titsc {
struct input_dev *input;
struct clk *tsc_ick;
void __iomem *tsc_base;
@@ -134,18 +134,18 @@ struct tscadc {
int steps_to_configure;
};
-static unsigned int tscadc_readl(struct tscadc *ts, unsigned int reg)
+static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
{
return readl(ts->tsc_base + reg);
}
-static void tscadc_writel(struct tscadc *tsc, unsigned int reg,
+static void titsc_writel(struct titsc *tsc, unsigned int reg,
unsigned int val)
{
writel(val, tsc->tsc_base + reg);
}
-static void tscadc_step_config(struct tscadc *ts_dev)
+static void titsc_step_config(struct titsc *ts_dev)
{
unsigned int config;
int i, total_steps;
@@ -170,8 +170,8 @@ static void tscadc_step_config(struct tscadc *ts_dev)
}
for (i = 1; i <= ts_dev->steps_to_configure; i++) {
- tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+ titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
}
config = 0;
@@ -192,8 +192,8 @@ static void tscadc_step_config(struct tscadc *ts_dev)
}
for (i = (ts_dev->steps_to_configure + 1); i <= total_steps; i++) {
- tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+ titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
}
config = 0;
@@ -202,40 +202,40 @@ static void tscadc_step_config(struct tscadc *ts_dev)
STEPCHARGE_RFP_XPUL | STEPCHARGE_RFM_XNUR |
STEPCHARGE_INM_AN1 | STEPCHARGE_INP_AN1;
- tscadc_writel(ts_dev, REG_CHARGECONFIG, config);
- tscadc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
+ titsc_writel(ts_dev, REG_CHARGECONFIG, config);
+ titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
config = 0;
/* Configure to calculate pressure */
config = STEPCONFIG_MODE_HWSYNC |
STEPCONFIG_AVG_16 | STEPCONFIG_YPP |
STEPCONFIG_XNN | STEPCONFIG_INM_ADCREFM;
- tscadc_writel(ts_dev, REG_STEPCONFIG(total_steps + 1), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(total_steps + 1),
+ titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 1), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 1),
STEPCONFIG_OPENDLY);
config |= STEPCONFIG_INP_AN3 | STEPCONFIG_FIFO1;
- tscadc_writel(ts_dev, REG_STEPCONFIG(total_steps + 2), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
+ titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 2), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
STEPCONFIG_OPENDLY);
- tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
}
-static void tscadc_idle_config(struct tscadc *ts_config)
+static void titsc_idle_config(struct titsc *ts_config)
{
unsigned int idleconfig;
idleconfig = STEPCONFIG_YNN |
STEPCONFIG_INM_ADCREFM |
STEPCONFIG_YPN | STEPCONFIG_INP_ADCREFM;
- tscadc_writel(ts_config, REG_IDLECONFIG, idleconfig);
+ titsc_writel(ts_config, REG_IDLECONFIG, idleconfig);
}
-static void tscadc_read_coordinates(struct tscadc *ts_dev,
+static void titsc_read_coordinates(struct titsc *ts_dev,
unsigned int *x, unsigned int *y)
{
- unsigned int fifocount = tscadc_readl(ts_dev, REG_FIFO0CNT);
+ unsigned int fifocount = titsc_readl(ts_dev, REG_FIFO0CNT);
unsigned int prev_val_x = ~0, prev_val_y = ~0;
unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
unsigned int read, diff;
@@ -250,7 +250,7 @@ static void tscadc_read_coordinates(struct tscadc *ts_dev,
* if true the value is reported to the sub system.
*/
for (i = 0; i < fifocount - 1; i++) {
- read = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
+ read = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
diff = abs(read - prev_val_x);
if (diff < prev_diff_x) {
prev_diff_x = diff;
@@ -258,7 +258,7 @@ static void tscadc_read_coordinates(struct tscadc *ts_dev,
}
prev_val_x = read;
- read = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
+ read = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
diff = abs(read - prev_val_y);
if (diff < prev_diff_y) {
prev_diff_y = diff;
@@ -268,21 +268,21 @@ static void tscadc_read_coordinates(struct tscadc *ts_dev,
}
}
-static irqreturn_t tscadc_irq(int irq, void *dev)
+static irqreturn_t titsc_irq(int irq, void *dev)
{
- struct tscadc *ts_dev = dev;
+ struct titsc *ts_dev = dev;
struct input_dev *input_dev = ts_dev->input;
unsigned int status, irqclr = 0;
unsigned int x = 0, y = 0;
unsigned int z1, z2, z;
unsigned int fsm;
- status = tscadc_readl(ts_dev, REG_IRQSTATUS);
+ status = titsc_readl(ts_dev, REG_IRQSTATUS);
if (status & IRQENB_FIFO0THRES) {
- tscadc_read_coordinates(ts_dev, &x, &y);
+ titsc_read_coordinates(ts_dev, &x, &y);
- z1 = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
- z2 = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
+ z1 = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
+ z2 = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
/*
@@ -313,10 +313,10 @@ static irqreturn_t tscadc_irq(int irq, void *dev)
*/
udelay(SEQ_SETTLE);
- status = tscadc_readl(ts_dev, REG_RAWIRQSTATUS);
+ status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
if (status & IRQENB_PENUP) {
/* Pen up event */
- fsm = tscadc_readl(ts_dev, REG_ADCFSM);
+ fsm = titsc_readl(ts_dev, REG_ADCFSM);
if (fsm == ADCFSM_STEPID) {
ts_dev->pen_down = false;
input_report_key(input_dev, BTN_TOUCH, 0);
@@ -328,9 +328,9 @@ static irqreturn_t tscadc_irq(int irq, void *dev)
irqclr |= IRQENB_PENUP;
}
- tscadc_writel(ts_dev, REG_IRQSTATUS, irqclr);
+ titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
- tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
return IRQ_HANDLED;
}
@@ -338,11 +338,11 @@ static irqreturn_t tscadc_irq(int irq, void *dev)
* The functions for inserting/removing driver as a module.
*/
-static int __devinit tscadc_probe(struct platform_device *pdev)
+static int __devinit titsc_probe(struct platform_device *pdev)
{
const struct tsc_data *pdata = pdev->dev.platform_data;
struct resource *res;
- struct tscadc *ts_dev;
+ struct titsc *ts_dev;
struct input_dev *input_dev;
struct clk *clk;
int err;
@@ -366,7 +366,7 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
}
/* Allocate memory for device */
- ts_dev = kzalloc(sizeof(struct tscadc), GFP_KERNEL);
+ ts_dev = kzalloc(sizeof(struct titsc), GFP_KERNEL);
input_dev = input_allocate_device();
if (!ts_dev || !input_dev) {
dev_err(&pdev->dev, "failed to allocate memory.\n");
@@ -394,7 +394,7 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
goto err_release_mem_region;
}
- err = request_irq(ts_dev->irq, tscadc_irq,
+ err = request_irq(ts_dev->irq, titsc_irq,
0, pdev->dev.driver->name, ts_dev);
if (err) {
dev_err(&pdev->dev, "failed to allocate irq.\n");
@@ -423,10 +423,10 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
goto err_disable_clk;
}
/* CLKDIV needs to be configured to the value minus 1 */
- tscadc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
+ titsc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
/* Enable wake-up of the SoC using touchscreen */
- tscadc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
+ titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
ctrl = CNTRLREG_STEPCONFIGWRT |
CNTRLREG_TSCENB |
@@ -442,15 +442,15 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
ctrl |= CNTRLREG_8WIRE;
break;
}
- tscadc_writel(ts_dev, REG_CTRL, ctrl);
+ titsc_writel(ts_dev, REG_CTRL, ctrl);
- tscadc_idle_config(ts_dev);
- tscadc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
- tscadc_step_config(ts_dev);
- tscadc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
+ titsc_idle_config(ts_dev);
+ titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
+ titsc_step_config(ts_dev);
+ titsc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
ctrl |= CNTRLREG_TSCSSENB;
- tscadc_writel(ts_dev, REG_CTRL, ctrl);
+ titsc_writel(ts_dev, REG_CTRL, ctrl);
input_dev->name = "ti-tsc-adc";
input_dev->dev.parent = &pdev->dev;
@@ -485,9 +485,9 @@ err_free_mem:
return err;
}
-static int __devexit tscadc_remove(struct platform_device *pdev)
+static int __devexit titsc_remove(struct platform_device *pdev)
{
- struct tscadc *ts_dev = platform_get_drvdata(pdev);
+ struct titsc *ts_dev = platform_get_drvdata(pdev);
struct resource *res;
free_irq(ts_dev->irq, ts_dev);
@@ -508,8 +508,8 @@ static int __devexit tscadc_remove(struct platform_device *pdev)
}
static struct platform_driver ti_tsc_driver = {
- .probe = tscadc_probe,
- .remove = __devexit_p(tscadc_remove),
+ .probe = titsc_probe,
+ .remove = __devexit_p(titsc_remove),
.driver = {
.name = "tsc",
.owner = THIS_MODULE,
diff --git a/include/linux/input/ti_tscadc.h b/include/linux/input/ti_am335x_tsc.h
similarity index 88%
rename from include/linux/input/ti_tscadc.h
rename to include/linux/input/ti_am335x_tsc.h
index ad442a3..49269a2 100644
--- a/include/linux/input/ti_tscadc.h
+++ b/include/linux/input/ti_am335x_tsc.h
@@ -1,5 +1,5 @@
-#ifndef __LINUX_TI_TSCADC_H
-#define __LINUX_TI_TSCADC_H
+#ifndef __LINUX_TI_AM335X_TSC_H
+#define __LINUX_TI_AM335X_TSC_H
/**
* struct tsc_data Touchscreen wire configuration
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 1/4] input: TSC: ti_tscadc: Rename the existing touchscreen driver
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
Make way for addition of MFD driver.
The existing touchsreen driver is a MFD client.
For better readability we rename the file to
indicate its functionality as only touchscreen.
Signed-off-by: Patil, Rachna <rachna-l0cyMroinI0@public.gmane.org>
---
Changes in v2:
Missed changing the name of touchscreen header file
in the previous version.
Adding the same.
Changes in v3:
no changes.
Changes in v4:
no changes.
Changes in v5:
updated the struct and function names to match
that of file name for better readability.
drivers/input/touchscreen/Kconfig | 4 +-
drivers/input/touchscreen/Makefile | 2 +-
.../touchscreen/{ti_tscadc.c => ti_am335x_tsc.c} | 96 ++++++++++----------
.../linux/input/{ti_tscadc.h => ti_am335x_tsc.h} | 4 +-
4 files changed, 53 insertions(+), 53 deletions(-)
rename drivers/input/touchscreen/{ti_tscadc.c => ti_am335x_tsc.c} (83%)
rename include/linux/input/{ti_tscadc.h => ti_am335x_tsc.h} (88%)
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 1ba232c..7bdb629 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -529,7 +529,7 @@ config TOUCHSCREEN_TOUCHWIN
To compile this driver as a module, choose M here: the
module will be called touchwin.
-config TOUCHSCREEN_TI_TSCADC
+config TOUCHSCREEN_TI_AM335X_TSC
tristate "TI Touchscreen Interface"
depends on ARCH_OMAP2PLUS
help
@@ -539,7 +539,7 @@ config TOUCHSCREEN_TI_TSCADC
If unsure, say N.
To compile this driver as a module, choose M here: the
- module will be called ti_tscadc.
+ module will be called ti_am335x_tsc.
config TOUCHSCREEN_ATMEL_TSADCC
tristate "Atmel Touchscreen Interface"
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 178eb12..7c4c78e 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -52,7 +52,7 @@ obj-$(CONFIG_TOUCHSCREEN_PIXCIR) += pixcir_i2c_ts.o
obj-$(CONFIG_TOUCHSCREEN_S3C2410) += s3c2410_ts.o
obj-$(CONFIG_TOUCHSCREEN_ST1232) += st1232.o
obj-$(CONFIG_TOUCHSCREEN_STMPE) += stmpe-ts.o
-obj-$(CONFIG_TOUCHSCREEN_TI_TSCADC) += ti_tscadc.o
+obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
obj-$(CONFIG_TOUCHSCREEN_TNETV107X) += tnetv107x-ts.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
diff --git a/drivers/input/touchscreen/ti_tscadc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
similarity index 83%
rename from drivers/input/touchscreen/ti_tscadc.c
rename to drivers/input/touchscreen/ti_am335x_tsc.c
index ec0a442..462950a 100644
--- a/drivers/input/touchscreen/ti_tscadc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -24,7 +24,7 @@
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <linux/input/ti_tscadc.h>
+#include <linux/input/ti_am335x_tsc.h>
#include <linux/delay.h>
#define REG_RAWIRQSTATUS 0x024
@@ -123,7 +123,7 @@
#define ADC_CLK 3000000
#define MAX_12BIT ((1 << 12) - 1)
-struct tscadc {
+struct titsc {
struct input_dev *input;
struct clk *tsc_ick;
void __iomem *tsc_base;
@@ -134,18 +134,18 @@ struct tscadc {
int steps_to_configure;
};
-static unsigned int tscadc_readl(struct tscadc *ts, unsigned int reg)
+static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
{
return readl(ts->tsc_base + reg);
}
-static void tscadc_writel(struct tscadc *tsc, unsigned int reg,
+static void titsc_writel(struct titsc *tsc, unsigned int reg,
unsigned int val)
{
writel(val, tsc->tsc_base + reg);
}
-static void tscadc_step_config(struct tscadc *ts_dev)
+static void titsc_step_config(struct titsc *ts_dev)
{
unsigned int config;
int i, total_steps;
@@ -170,8 +170,8 @@ static void tscadc_step_config(struct tscadc *ts_dev)
}
for (i = 1; i <= ts_dev->steps_to_configure; i++) {
- tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+ titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
}
config = 0;
@@ -192,8 +192,8 @@ static void tscadc_step_config(struct tscadc *ts_dev)
}
for (i = (ts_dev->steps_to_configure + 1); i <= total_steps; i++) {
- tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+ titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
}
config = 0;
@@ -202,40 +202,40 @@ static void tscadc_step_config(struct tscadc *ts_dev)
STEPCHARGE_RFP_XPUL | STEPCHARGE_RFM_XNUR |
STEPCHARGE_INM_AN1 | STEPCHARGE_INP_AN1;
- tscadc_writel(ts_dev, REG_CHARGECONFIG, config);
- tscadc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
+ titsc_writel(ts_dev, REG_CHARGECONFIG, config);
+ titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
config = 0;
/* Configure to calculate pressure */
config = STEPCONFIG_MODE_HWSYNC |
STEPCONFIG_AVG_16 | STEPCONFIG_YPP |
STEPCONFIG_XNN | STEPCONFIG_INM_ADCREFM;
- tscadc_writel(ts_dev, REG_STEPCONFIG(total_steps + 1), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(total_steps + 1),
+ titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 1), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 1),
STEPCONFIG_OPENDLY);
config |= STEPCONFIG_INP_AN3 | STEPCONFIG_FIFO1;
- tscadc_writel(ts_dev, REG_STEPCONFIG(total_steps + 2), config);
- tscadc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
+ titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 2), config);
+ titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
STEPCONFIG_OPENDLY);
- tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
}
-static void tscadc_idle_config(struct tscadc *ts_config)
+static void titsc_idle_config(struct titsc *ts_config)
{
unsigned int idleconfig;
idleconfig = STEPCONFIG_YNN |
STEPCONFIG_INM_ADCREFM |
STEPCONFIG_YPN | STEPCONFIG_INP_ADCREFM;
- tscadc_writel(ts_config, REG_IDLECONFIG, idleconfig);
+ titsc_writel(ts_config, REG_IDLECONFIG, idleconfig);
}
-static void tscadc_read_coordinates(struct tscadc *ts_dev,
+static void titsc_read_coordinates(struct titsc *ts_dev,
unsigned int *x, unsigned int *y)
{
- unsigned int fifocount = tscadc_readl(ts_dev, REG_FIFO0CNT);
+ unsigned int fifocount = titsc_readl(ts_dev, REG_FIFO0CNT);
unsigned int prev_val_x = ~0, prev_val_y = ~0;
unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
unsigned int read, diff;
@@ -250,7 +250,7 @@ static void tscadc_read_coordinates(struct tscadc *ts_dev,
* if true the value is reported to the sub system.
*/
for (i = 0; i < fifocount - 1; i++) {
- read = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
+ read = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
diff = abs(read - prev_val_x);
if (diff < prev_diff_x) {
prev_diff_x = diff;
@@ -258,7 +258,7 @@ static void tscadc_read_coordinates(struct tscadc *ts_dev,
}
prev_val_x = read;
- read = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
+ read = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
diff = abs(read - prev_val_y);
if (diff < prev_diff_y) {
prev_diff_y = diff;
@@ -268,21 +268,21 @@ static void tscadc_read_coordinates(struct tscadc *ts_dev,
}
}
-static irqreturn_t tscadc_irq(int irq, void *dev)
+static irqreturn_t titsc_irq(int irq, void *dev)
{
- struct tscadc *ts_dev = dev;
+ struct titsc *ts_dev = dev;
struct input_dev *input_dev = ts_dev->input;
unsigned int status, irqclr = 0;
unsigned int x = 0, y = 0;
unsigned int z1, z2, z;
unsigned int fsm;
- status = tscadc_readl(ts_dev, REG_IRQSTATUS);
+ status = titsc_readl(ts_dev, REG_IRQSTATUS);
if (status & IRQENB_FIFO0THRES) {
- tscadc_read_coordinates(ts_dev, &x, &y);
+ titsc_read_coordinates(ts_dev, &x, &y);
- z1 = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
- z2 = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
+ z1 = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
+ z2 = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
/*
@@ -313,10 +313,10 @@ static irqreturn_t tscadc_irq(int irq, void *dev)
*/
udelay(SEQ_SETTLE);
- status = tscadc_readl(ts_dev, REG_RAWIRQSTATUS);
+ status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
if (status & IRQENB_PENUP) {
/* Pen up event */
- fsm = tscadc_readl(ts_dev, REG_ADCFSM);
+ fsm = titsc_readl(ts_dev, REG_ADCFSM);
if (fsm == ADCFSM_STEPID) {
ts_dev->pen_down = false;
input_report_key(input_dev, BTN_TOUCH, 0);
@@ -328,9 +328,9 @@ static irqreturn_t tscadc_irq(int irq, void *dev)
irqclr |= IRQENB_PENUP;
}
- tscadc_writel(ts_dev, REG_IRQSTATUS, irqclr);
+ titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
- tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
return IRQ_HANDLED;
}
@@ -338,11 +338,11 @@ static irqreturn_t tscadc_irq(int irq, void *dev)
* The functions for inserting/removing driver as a module.
*/
-static int __devinit tscadc_probe(struct platform_device *pdev)
+static int __devinit titsc_probe(struct platform_device *pdev)
{
const struct tsc_data *pdata = pdev->dev.platform_data;
struct resource *res;
- struct tscadc *ts_dev;
+ struct titsc *ts_dev;
struct input_dev *input_dev;
struct clk *clk;
int err;
@@ -366,7 +366,7 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
}
/* Allocate memory for device */
- ts_dev = kzalloc(sizeof(struct tscadc), GFP_KERNEL);
+ ts_dev = kzalloc(sizeof(struct titsc), GFP_KERNEL);
input_dev = input_allocate_device();
if (!ts_dev || !input_dev) {
dev_err(&pdev->dev, "failed to allocate memory.\n");
@@ -394,7 +394,7 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
goto err_release_mem_region;
}
- err = request_irq(ts_dev->irq, tscadc_irq,
+ err = request_irq(ts_dev->irq, titsc_irq,
0, pdev->dev.driver->name, ts_dev);
if (err) {
dev_err(&pdev->dev, "failed to allocate irq.\n");
@@ -423,10 +423,10 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
goto err_disable_clk;
}
/* CLKDIV needs to be configured to the value minus 1 */
- tscadc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
+ titsc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
/* Enable wake-up of the SoC using touchscreen */
- tscadc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
+ titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
ctrl = CNTRLREG_STEPCONFIGWRT |
CNTRLREG_TSCENB |
@@ -442,15 +442,15 @@ static int __devinit tscadc_probe(struct platform_device *pdev)
ctrl |= CNTRLREG_8WIRE;
break;
}
- tscadc_writel(ts_dev, REG_CTRL, ctrl);
+ titsc_writel(ts_dev, REG_CTRL, ctrl);
- tscadc_idle_config(ts_dev);
- tscadc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
- tscadc_step_config(ts_dev);
- tscadc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
+ titsc_idle_config(ts_dev);
+ titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
+ titsc_step_config(ts_dev);
+ titsc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
ctrl |= CNTRLREG_TSCSSENB;
- tscadc_writel(ts_dev, REG_CTRL, ctrl);
+ titsc_writel(ts_dev, REG_CTRL, ctrl);
input_dev->name = "ti-tsc-adc";
input_dev->dev.parent = &pdev->dev;
@@ -485,9 +485,9 @@ err_free_mem:
return err;
}
-static int __devexit tscadc_remove(struct platform_device *pdev)
+static int __devexit titsc_remove(struct platform_device *pdev)
{
- struct tscadc *ts_dev = platform_get_drvdata(pdev);
+ struct titsc *ts_dev = platform_get_drvdata(pdev);
struct resource *res;
free_irq(ts_dev->irq, ts_dev);
@@ -508,8 +508,8 @@ static int __devexit tscadc_remove(struct platform_device *pdev)
}
static struct platform_driver ti_tsc_driver = {
- .probe = tscadc_probe,
- .remove = __devexit_p(tscadc_remove),
+ .probe = titsc_probe,
+ .remove = __devexit_p(titsc_remove),
.driver = {
.name = "tsc",
.owner = THIS_MODULE,
diff --git a/include/linux/input/ti_tscadc.h b/include/linux/input/ti_am335x_tsc.h
similarity index 88%
rename from include/linux/input/ti_tscadc.h
rename to include/linux/input/ti_am335x_tsc.h
index ad442a3..49269a2 100644
--- a/include/linux/input/ti_tscadc.h
+++ b/include/linux/input/ti_am335x_tsc.h
@@ -1,5 +1,5 @@
-#ifndef __LINUX_TI_TSCADC_H
-#define __LINUX_TI_TSCADC_H
+#ifndef __LINUX_TI_AM335X_TSC_H
+#define __LINUX_TI_AM335X_TSC_H
/**
* struct tsc_data Touchscreen wire configuration
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 2/4] MFD: ti_tscadc: Add support for TI's TSC/ADC MFDevice
2012-10-05 7:34 ` Patil, Rachna
@ 2012-10-05 7:34 ` Patil, Rachna
-1 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
Add the mfd core driver which supports touchscreen
and ADC.
With this patch we are only adding infrastructure to
support the MFD clients.
Signed-off-by: Patil, Rachna <rachna@ti.com>
---
Changes in v2:
Merged "[PATCH 5/5] MFD: ti_tscadc: Add check on number of i/p channels",
patch submitted in previous version into this file.
Changes in v3:
No changes
Changes in v4:
No changes
Changes in v5:
Make use of devm_xxx and regmap MMIO API's.
drivers/mfd/Kconfig | 11 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/ti_am335x_tscadc.c | 250 ++++++++++++++++++++++++++++++++++
include/linux/mfd/ti_am335x_tscadc.h | 137 +++++++++++++++++++
4 files changed, 399 insertions(+), 0 deletions(-)
create mode 100644 drivers/mfd/ti_am335x_tscadc.c
create mode 100644 include/linux/mfd/ti_am335x_tscadc.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b1a1462..8a1d655 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -94,6 +94,17 @@ config MFD_TI_SSP
To compile this driver as a module, choose M here: the
module will be called ti-ssp.
+config MFD_TI_AM335X_TSCADC
+ tristate "TI ADC / Touch Screen chip support"
+ select MFD_CORE
+ select REGMAP
+ select REGMAP_MMIO
+ help
+ If you say yes here you get support for Texas Instruments series
+ of Touch Screen /ADC chips.
+ To compile this driver as a module, choose M here: the
+ module will be called ti_am335x_tscadc.
+
config HTC_EGPIO
bool "HTC EGPIO support"
depends on GENERIC_HARDIRQS && GPIOLIB && ARM
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 79dd22d..bc6b2f0 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_HTC_I2CPLD) += htc-i2cpld.o
obj-$(CONFIG_MFD_DAVINCI_VOICECODEC) += davinci_voicecodec.o
obj-$(CONFIG_MFD_DM355EVM_MSP) += dm355evm_msp.o
obj-$(CONFIG_MFD_TI_SSP) += ti-ssp.o
+obj-$(CONFIG_MFD_TI_AM335X_TSCADC) += ti_am335x_tscadc.o
obj-$(CONFIG_MFD_STA2X11) += sta2x11-mfd.o
obj-$(CONFIG_MFD_STMPE) += stmpe.o
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
new file mode 100644
index 0000000..14df67b
--- /dev/null
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -0,0 +1,250 @@
+/*
+ * TI Touch Screen / ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/mfd/core.h>
+#include <linux/pm_runtime.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+
+static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
+{
+ unsigned int val;
+
+ regmap_read(tsadc->regmap_tscadc, reg, &val);
+ return val;
+}
+
+static void tscadc_writel(struct ti_tscadc_dev *tsadc, unsigned int reg,
+ unsigned int val)
+{
+ regmap_write(tsadc->regmap_tscadc, reg, val);
+}
+
+static const struct regmap_config tscadc_regmap_config = {
+ .name = "ti_tscadc",
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+};
+
+static void tscadc_idle_config(struct ti_tscadc_dev *config)
+{
+ unsigned int idleconfig;
+
+ idleconfig = STEPCONFIG_YNN | STEPCONFIG_INM_ADCREFM |
+ STEPCONFIG_INP_ADCREFM | STEPCONFIG_YPN;
+
+ tscadc_writel(config, REG_IDLECONFIG, idleconfig);
+}
+
+static int __devinit ti_tscadc_probe(struct platform_device *pdev)
+{
+ struct ti_tscadc_dev *tscadc;
+ struct resource *res;
+ struct clk *clk;
+ struct mfd_tscadc_board *pdata = pdev->dev.platform_data;
+ int irq;
+ int err, ctrl;
+ int clk_value, clock_rate;
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "Could not find platform data\n");
+ return -EINVAL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "no memory resource defined.\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no irq ID is specified.\n");
+ return -EINVAL;
+ }
+
+ /* Allocate memory for device */
+ tscadc = devm_kzalloc(&pdev->dev,
+ sizeof(struct ti_tscadc_dev), GFP_KERNEL);
+ if (!tscadc) {
+ dev_err(&pdev->dev, "failed to allocate memory.\n");
+ return -ENOMEM;
+ }
+ tscadc->dev = &pdev->dev;
+ tscadc->irq = irq;
+
+ res = devm_request_mem_region(&pdev->dev,
+ res->start, resource_size(res), pdev->name);
+ if (!res) {
+ dev_err(&pdev->dev, "failed to reserve registers.\n");
+ err = -EBUSY;
+ goto err;
+ }
+
+ tscadc->tscadc_base = devm_ioremap(&pdev->dev,
+ res->start, resource_size(res));
+ if (!tscadc->tscadc_base) {
+ dev_err(&pdev->dev, "failed to map registers.\n");
+ err = -ENOMEM;
+ goto err;
+ }
+
+ tscadc->regmap_tscadc = devm_regmap_init_mmio(&pdev->dev,
+ tscadc->tscadc_base, &tscadc_regmap_config);
+ if (IS_ERR(tscadc->regmap_tscadc)) {
+ dev_err(&pdev->dev, "regmap init failed\n");
+ err = PTR_ERR(tscadc->regmap_tscadc);
+ goto err;
+ }
+
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_get_sync(&pdev->dev);
+
+ /*
+ * The TSC_ADC_Subsystem has 2 clock domains
+ * OCP_CLK and ADC_CLK.
+ * The ADC clock is expected to run at target of 3MHz,
+ * and expected to capture 12-bit data at a rate of 200 KSPS.
+ * The TSC_ADC_SS controller design assumes the OCP clock is
+ * at least 6x faster than the ADC clock.
+ */
+ clk = clk_get(&pdev->dev, "adc_tsc_fck");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "failed to get TSC fck\n");
+ err = PTR_ERR(clk);
+ goto err_disable_clk;
+ }
+ clock_rate = clk_get_rate(clk);
+ clk_put(clk);
+ clk_value = clock_rate / ADC_CLK;
+ if (clk_value < MAX_CLK_DIV) {
+ dev_err(&pdev->dev, "clock input less than min clock requirement\n");
+ err = -EINVAL;
+ goto err_disable_clk;
+ }
+ /* TSCADC_CLKDIV needs to be configured to the value minus 1 */
+ clk_value = clk_value - 1;
+ tscadc_writel(tscadc, REG_CLKDIV, clk_value);
+
+ /* Set the control register bits */
+ ctrl = CNTRLREG_STEPCONFIGWRT |
+ CNTRLREG_TSCENB |
+ CNTRLREG_STEPID |
+ CNTRLREG_4WIRE;
+ tscadc_writel(tscadc, REG_CTRL, ctrl);
+
+ /* Set register bits for Idle Config Mode */
+ tscadc_idle_config(tscadc);
+
+ /* Enable the TSC module enable bit */
+ ctrl = tscadc_readl(tscadc, REG_CTRL);
+ ctrl |= CNTRLREG_TSCSSENB;
+ tscadc_writel(tscadc, REG_CTRL, ctrl);
+
+ err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
+ TSCADC_CELLS, NULL, 0, NULL);
+ if (err < 0)
+ goto err_disable_clk;
+
+ device_init_wakeup(&pdev->dev, true);
+ platform_set_drvdata(pdev, tscadc);
+
+ return 0;
+
+err_disable_clk:
+ pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+err:
+ return err;
+}
+
+static int __devexit ti_tscadc_remove(struct platform_device *pdev)
+{
+ struct ti_tscadc_dev *tscadc = platform_get_drvdata(pdev);
+
+ tscadc_writel(tscadc, REG_SE, 0x00);
+
+ pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+
+ mfd_remove_devices(tscadc->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int tscadc_suspend(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev_get_drvdata(dev);
+
+ tscadc_writel(tscadc_dev, REG_SE, 0x00);
+ pm_runtime_put_sync(dev);
+
+ return 0;
+}
+
+static int tscadc_resume(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev_get_drvdata(dev);
+ unsigned int restore, ctrl;
+
+ pm_runtime_get_sync(dev);
+
+ /* context restore */
+ ctrl = CNTRLREG_STEPCONFIGWRT | CNTRLREG_TSCENB |
+ CNTRLREG_STEPID | CNTRLREG_4WIRE;
+ tscadc_writel(tscadc_dev, REG_CTRL, ctrl);
+ tscadc_idle_config(tscadc_dev);
+ tscadc_writel(tscadc_dev, REG_SE, STPENB_STEPENB);
+ restore = tscadc_readl(tscadc_dev, REG_CTRL);
+ tscadc_writel(tscadc_dev, REG_CTRL,
+ (restore | CNTRLREG_TSCSSENB));
+
+ return 0;
+}
+
+static const struct dev_pm_ops tscadc_pm_ops = {
+ .suspend = tscadc_suspend,
+ .resume = tscadc_resume,
+};
+#define TSCADC_PM_OPS (&tscadc_pm_ops)
+#else
+#define TSCADC_PM_OPS NULL
+#endif
+
+static struct platform_driver ti_tscadc_driver = {
+ .driver = {
+ .name = "ti_tscadc",
+ .owner = THIS_MODULE,
+ .pm = TSCADC_PM_OPS,
+ },
+ .probe = ti_tscadc_probe,
+ .remove = __devexit_p(ti_tscadc_remove),
+
+};
+
+module_platform_driver(ti_tscadc_driver);
+
+MODULE_DESCRIPTION("TI touchscreen / ADC MFD controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
new file mode 100644
index 0000000..b7232b1
--- /dev/null
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -0,0 +1,137 @@
+#ifndef __LINUX_TI_AM335X_TSCADC_MFD_H
+#define __LINUX_TI_AM335X_TSCADC_MFD_H
+
+/*
+ * TI Touch Screen / ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/mfd/core.h>
+
+#define REG_RAWIRQSTATUS 0x024
+#define REG_IRQSTATUS 0x028
+#define REG_IRQENABLE 0x02C
+#define REG_IRQCLR 0x030
+#define REG_IRQWAKEUP 0x034
+#define REG_CTRL 0x040
+#define REG_ADCFSM 0x044
+#define REG_CLKDIV 0x04C
+#define REG_SE 0x054
+#define REG_IDLECONFIG 0x058
+#define REG_CHARGECONFIG 0x05C
+#define REG_CHARGEDELAY 0x060
+#define REG_STEPCONFIG(n) (0x64 + ((n - 1) * 8))
+#define REG_STEPDELAY(n) (0x68 + ((n - 1) * 8))
+#define REG_FIFO0CNT 0xE4
+#define REG_FIFO0THR 0xE8
+#define REG_FIFO1CNT 0xF0
+#define REG_FIFO1THR 0xF4
+#define REG_FIFO0 0x100
+#define REG_FIFO1 0x200
+
+/* Register Bitfields */
+/* IRQ wakeup enable */
+#define IRQWKUP_ENB BIT(0)
+
+/* Step Enable */
+#define STEPENB_MASK (0x1FFFF << 0)
+#define STEPENB(val) ((val) << 0)
+#define STPENB_STEPENB STEPENB(0x1FFFF)
+
+/* IRQ enable */
+#define IRQENB_HW_PEN BIT(0)
+#define IRQENB_FIFO0THRES BIT(2)
+#define IRQENB_FIFO1THRES BIT(5)
+#define IRQENB_PENUP BIT(9)
+
+/* Step Configuration */
+#define STEPCONFIG_MODE_MASK (3 << 0)
+#define STEPCONFIG_MODE(val) ((val) << 0)
+#define STEPCONFIG_MODE_HWSYNC STEPCONFIG_MODE(2)
+#define STEPCONFIG_AVG_MASK (7 << 2)
+#define STEPCONFIG_AVG(val) ((val) << 2)
+#define STEPCONFIG_AVG_16 STEPCONFIG_AVG(4)
+#define STEPCONFIG_XPP BIT(5)
+#define STEPCONFIG_XNN BIT(6)
+#define STEPCONFIG_YPP BIT(7)
+#define STEPCONFIG_YNN BIT(8)
+#define STEPCONFIG_XNP BIT(9)
+#define STEPCONFIG_YPN BIT(10)
+#define STEPCONFIG_INM_MASK (0xF << 15)
+#define STEPCONFIG_INM(val) ((val) << 15)
+#define STEPCONFIG_INM_ADCREFM STEPCONFIG_INM(8)
+#define STEPCONFIG_INP_MASK (0xF << 19)
+#define STEPCONFIG_INP(val) ((val) << 19)
+#define STEPCONFIG_INP_AN2 STEPCONFIG_INP(2)
+#define STEPCONFIG_INP_AN3 STEPCONFIG_INP(3)
+#define STEPCONFIG_INP_AN4 STEPCONFIG_INP(4)
+#define STEPCONFIG_INP_ADCREFM STEPCONFIG_INP(8)
+#define STEPCONFIG_FIFO1 BIT(26)
+
+/* Delay register */
+#define STEPDELAY_OPEN_MASK (0x3FFFF << 0)
+#define STEPDELAY_OPEN(val) ((val) << 0)
+#define STEPCONFIG_OPENDLY STEPDELAY_OPEN(0x098)
+#define STEPDELAY_SAMPLE_MASK (0xFF << 24)
+#define STEPDELAY_SAMPLE(val) ((val) << 24)
+#define STEPCONFIG_SAMPLEDLY STEPDELAY_SAMPLE(0)
+
+/* Charge Config */
+#define STEPCHARGE_RFP_MASK (7 << 12)
+#define STEPCHARGE_RFP(val) ((val) << 12)
+#define STEPCHARGE_RFP_XPUL STEPCHARGE_RFP(1)
+#define STEPCHARGE_INM_MASK (0xF << 15)
+#define STEPCHARGE_INM(val) ((val) << 15)
+#define STEPCHARGE_INM_AN1 STEPCHARGE_INM(1)
+#define STEPCHARGE_INP_MASK (0xF << 19)
+#define STEPCHARGE_INP(val) ((val) << 19)
+#define STEPCHARGE_INP_AN1 STEPCHARGE_INP(1)
+#define STEPCHARGE_RFM_MASK (3 << 23)
+#define STEPCHARGE_RFM(val) ((val) << 23)
+#define STEPCHARGE_RFM_XNUR STEPCHARGE_RFM(1)
+
+/* Charge delay */
+#define CHARGEDLY_OPEN_MASK (0x3FFFF << 0)
+#define CHARGEDLY_OPEN(val) ((val) << 0)
+#define CHARGEDLY_OPENDLY CHARGEDLY_OPEN(1)
+
+/* Control register */
+#define CNTRLREG_TSCSSENB BIT(0)
+#define CNTRLREG_STEPID BIT(1)
+#define CNTRLREG_STEPCONFIGWRT BIT(2)
+#define CNTRLREG_POWERDOWN BIT(4)
+#define CNTRLREG_AFE_CTRL_MASK (3 << 5)
+#define CNTRLREG_AFE_CTRL(val) ((val) << 5)
+#define CNTRLREG_4WIRE CNTRLREG_AFE_CTRL(1)
+#define CNTRLREG_5WIRE CNTRLREG_AFE_CTRL(2)
+#define CNTRLREG_8WIRE CNTRLREG_AFE_CTRL(3)
+#define CNTRLREG_TSCENB BIT(7)
+
+#define ADC_CLK 3000000
+#define MAX_CLK_DIV 7
+
+#define TSCADC_CELLS 0
+
+struct mfd_tscadc_board {
+ struct tsc_data *tsc_init;
+};
+
+struct ti_tscadc_dev {
+ struct device *dev;
+ struct regmap *regmap_tscadc;
+ void __iomem *tscadc_base;
+ int irq;
+ struct mfd_cell cells[TSCADC_CELLS];
+};
+
+#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 2/4] MFD: ti_tscadc: Add support for TI's TSC/ADC MFDevice
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
Add the mfd core driver which supports touchscreen
and ADC.
With this patch we are only adding infrastructure to
support the MFD clients.
Signed-off-by: Patil, Rachna <rachna@ti.com>
---
Changes in v2:
Merged "[PATCH 5/5] MFD: ti_tscadc: Add check on number of i/p channels",
patch submitted in previous version into this file.
Changes in v3:
No changes
Changes in v4:
No changes
Changes in v5:
Make use of devm_xxx and regmap MMIO API's.
drivers/mfd/Kconfig | 11 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/ti_am335x_tscadc.c | 250 ++++++++++++++++++++++++++++++++++
include/linux/mfd/ti_am335x_tscadc.h | 137 +++++++++++++++++++
4 files changed, 399 insertions(+), 0 deletions(-)
create mode 100644 drivers/mfd/ti_am335x_tscadc.c
create mode 100644 include/linux/mfd/ti_am335x_tscadc.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b1a1462..8a1d655 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -94,6 +94,17 @@ config MFD_TI_SSP
To compile this driver as a module, choose M here: the
module will be called ti-ssp.
+config MFD_TI_AM335X_TSCADC
+ tristate "TI ADC / Touch Screen chip support"
+ select MFD_CORE
+ select REGMAP
+ select REGMAP_MMIO
+ help
+ If you say yes here you get support for Texas Instruments series
+ of Touch Screen /ADC chips.
+ To compile this driver as a module, choose M here: the
+ module will be called ti_am335x_tscadc.
+
config HTC_EGPIO
bool "HTC EGPIO support"
depends on GENERIC_HARDIRQS && GPIOLIB && ARM
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 79dd22d..bc6b2f0 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_HTC_I2CPLD) += htc-i2cpld.o
obj-$(CONFIG_MFD_DAVINCI_VOICECODEC) += davinci_voicecodec.o
obj-$(CONFIG_MFD_DM355EVM_MSP) += dm355evm_msp.o
obj-$(CONFIG_MFD_TI_SSP) += ti-ssp.o
+obj-$(CONFIG_MFD_TI_AM335X_TSCADC) += ti_am335x_tscadc.o
obj-$(CONFIG_MFD_STA2X11) += sta2x11-mfd.o
obj-$(CONFIG_MFD_STMPE) += stmpe.o
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
new file mode 100644
index 0000000..14df67b
--- /dev/null
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -0,0 +1,250 @@
+/*
+ * TI Touch Screen / ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/mfd/core.h>
+#include <linux/pm_runtime.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+
+static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
+{
+ unsigned int val;
+
+ regmap_read(tsadc->regmap_tscadc, reg, &val);
+ return val;
+}
+
+static void tscadc_writel(struct ti_tscadc_dev *tsadc, unsigned int reg,
+ unsigned int val)
+{
+ regmap_write(tsadc->regmap_tscadc, reg, val);
+}
+
+static const struct regmap_config tscadc_regmap_config = {
+ .name = "ti_tscadc",
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+};
+
+static void tscadc_idle_config(struct ti_tscadc_dev *config)
+{
+ unsigned int idleconfig;
+
+ idleconfig = STEPCONFIG_YNN | STEPCONFIG_INM_ADCREFM |
+ STEPCONFIG_INP_ADCREFM | STEPCONFIG_YPN;
+
+ tscadc_writel(config, REG_IDLECONFIG, idleconfig);
+}
+
+static int __devinit ti_tscadc_probe(struct platform_device *pdev)
+{
+ struct ti_tscadc_dev *tscadc;
+ struct resource *res;
+ struct clk *clk;
+ struct mfd_tscadc_board *pdata = pdev->dev.platform_data;
+ int irq;
+ int err, ctrl;
+ int clk_value, clock_rate;
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "Could not find platform data\n");
+ return -EINVAL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "no memory resource defined.\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no irq ID is specified.\n");
+ return -EINVAL;
+ }
+
+ /* Allocate memory for device */
+ tscadc = devm_kzalloc(&pdev->dev,
+ sizeof(struct ti_tscadc_dev), GFP_KERNEL);
+ if (!tscadc) {
+ dev_err(&pdev->dev, "failed to allocate memory.\n");
+ return -ENOMEM;
+ }
+ tscadc->dev = &pdev->dev;
+ tscadc->irq = irq;
+
+ res = devm_request_mem_region(&pdev->dev,
+ res->start, resource_size(res), pdev->name);
+ if (!res) {
+ dev_err(&pdev->dev, "failed to reserve registers.\n");
+ err = -EBUSY;
+ goto err;
+ }
+
+ tscadc->tscadc_base = devm_ioremap(&pdev->dev,
+ res->start, resource_size(res));
+ if (!tscadc->tscadc_base) {
+ dev_err(&pdev->dev, "failed to map registers.\n");
+ err = -ENOMEM;
+ goto err;
+ }
+
+ tscadc->regmap_tscadc = devm_regmap_init_mmio(&pdev->dev,
+ tscadc->tscadc_base, &tscadc_regmap_config);
+ if (IS_ERR(tscadc->regmap_tscadc)) {
+ dev_err(&pdev->dev, "regmap init failed\n");
+ err = PTR_ERR(tscadc->regmap_tscadc);
+ goto err;
+ }
+
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_get_sync(&pdev->dev);
+
+ /*
+ * The TSC_ADC_Subsystem has 2 clock domains
+ * OCP_CLK and ADC_CLK.
+ * The ADC clock is expected to run at target of 3MHz,
+ * and expected to capture 12-bit data at a rate of 200 KSPS.
+ * The TSC_ADC_SS controller design assumes the OCP clock is
+ * at least 6x faster than the ADC clock.
+ */
+ clk = clk_get(&pdev->dev, "adc_tsc_fck");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "failed to get TSC fck\n");
+ err = PTR_ERR(clk);
+ goto err_disable_clk;
+ }
+ clock_rate = clk_get_rate(clk);
+ clk_put(clk);
+ clk_value = clock_rate / ADC_CLK;
+ if (clk_value < MAX_CLK_DIV) {
+ dev_err(&pdev->dev, "clock input less than min clock requirement\n");
+ err = -EINVAL;
+ goto err_disable_clk;
+ }
+ /* TSCADC_CLKDIV needs to be configured to the value minus 1 */
+ clk_value = clk_value - 1;
+ tscadc_writel(tscadc, REG_CLKDIV, clk_value);
+
+ /* Set the control register bits */
+ ctrl = CNTRLREG_STEPCONFIGWRT |
+ CNTRLREG_TSCENB |
+ CNTRLREG_STEPID |
+ CNTRLREG_4WIRE;
+ tscadc_writel(tscadc, REG_CTRL, ctrl);
+
+ /* Set register bits for Idle Config Mode */
+ tscadc_idle_config(tscadc);
+
+ /* Enable the TSC module enable bit */
+ ctrl = tscadc_readl(tscadc, REG_CTRL);
+ ctrl |= CNTRLREG_TSCSSENB;
+ tscadc_writel(tscadc, REG_CTRL, ctrl);
+
+ err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
+ TSCADC_CELLS, NULL, 0, NULL);
+ if (err < 0)
+ goto err_disable_clk;
+
+ device_init_wakeup(&pdev->dev, true);
+ platform_set_drvdata(pdev, tscadc);
+
+ return 0;
+
+err_disable_clk:
+ pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+err:
+ return err;
+}
+
+static int __devexit ti_tscadc_remove(struct platform_device *pdev)
+{
+ struct ti_tscadc_dev *tscadc = platform_get_drvdata(pdev);
+
+ tscadc_writel(tscadc, REG_SE, 0x00);
+
+ pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+
+ mfd_remove_devices(tscadc->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int tscadc_suspend(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev_get_drvdata(dev);
+
+ tscadc_writel(tscadc_dev, REG_SE, 0x00);
+ pm_runtime_put_sync(dev);
+
+ return 0;
+}
+
+static int tscadc_resume(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev_get_drvdata(dev);
+ unsigned int restore, ctrl;
+
+ pm_runtime_get_sync(dev);
+
+ /* context restore */
+ ctrl = CNTRLREG_STEPCONFIGWRT | CNTRLREG_TSCENB |
+ CNTRLREG_STEPID | CNTRLREG_4WIRE;
+ tscadc_writel(tscadc_dev, REG_CTRL, ctrl);
+ tscadc_idle_config(tscadc_dev);
+ tscadc_writel(tscadc_dev, REG_SE, STPENB_STEPENB);
+ restore = tscadc_readl(tscadc_dev, REG_CTRL);
+ tscadc_writel(tscadc_dev, REG_CTRL,
+ (restore | CNTRLREG_TSCSSENB));
+
+ return 0;
+}
+
+static const struct dev_pm_ops tscadc_pm_ops = {
+ .suspend = tscadc_suspend,
+ .resume = tscadc_resume,
+};
+#define TSCADC_PM_OPS (&tscadc_pm_ops)
+#else
+#define TSCADC_PM_OPS NULL
+#endif
+
+static struct platform_driver ti_tscadc_driver = {
+ .driver = {
+ .name = "ti_tscadc",
+ .owner = THIS_MODULE,
+ .pm = TSCADC_PM_OPS,
+ },
+ .probe = ti_tscadc_probe,
+ .remove = __devexit_p(ti_tscadc_remove),
+
+};
+
+module_platform_driver(ti_tscadc_driver);
+
+MODULE_DESCRIPTION("TI touchscreen / ADC MFD controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
new file mode 100644
index 0000000..b7232b1
--- /dev/null
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -0,0 +1,137 @@
+#ifndef __LINUX_TI_AM335X_TSCADC_MFD_H
+#define __LINUX_TI_AM335X_TSCADC_MFD_H
+
+/*
+ * TI Touch Screen / ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/mfd/core.h>
+
+#define REG_RAWIRQSTATUS 0x024
+#define REG_IRQSTATUS 0x028
+#define REG_IRQENABLE 0x02C
+#define REG_IRQCLR 0x030
+#define REG_IRQWAKEUP 0x034
+#define REG_CTRL 0x040
+#define REG_ADCFSM 0x044
+#define REG_CLKDIV 0x04C
+#define REG_SE 0x054
+#define REG_IDLECONFIG 0x058
+#define REG_CHARGECONFIG 0x05C
+#define REG_CHARGEDELAY 0x060
+#define REG_STEPCONFIG(n) (0x64 + ((n - 1) * 8))
+#define REG_STEPDELAY(n) (0x68 + ((n - 1) * 8))
+#define REG_FIFO0CNT 0xE4
+#define REG_FIFO0THR 0xE8
+#define REG_FIFO1CNT 0xF0
+#define REG_FIFO1THR 0xF4
+#define REG_FIFO0 0x100
+#define REG_FIFO1 0x200
+
+/* Register Bitfields */
+/* IRQ wakeup enable */
+#define IRQWKUP_ENB BIT(0)
+
+/* Step Enable */
+#define STEPENB_MASK (0x1FFFF << 0)
+#define STEPENB(val) ((val) << 0)
+#define STPENB_STEPENB STEPENB(0x1FFFF)
+
+/* IRQ enable */
+#define IRQENB_HW_PEN BIT(0)
+#define IRQENB_FIFO0THRES BIT(2)
+#define IRQENB_FIFO1THRES BIT(5)
+#define IRQENB_PENUP BIT(9)
+
+/* Step Configuration */
+#define STEPCONFIG_MODE_MASK (3 << 0)
+#define STEPCONFIG_MODE(val) ((val) << 0)
+#define STEPCONFIG_MODE_HWSYNC STEPCONFIG_MODE(2)
+#define STEPCONFIG_AVG_MASK (7 << 2)
+#define STEPCONFIG_AVG(val) ((val) << 2)
+#define STEPCONFIG_AVG_16 STEPCONFIG_AVG(4)
+#define STEPCONFIG_XPP BIT(5)
+#define STEPCONFIG_XNN BIT(6)
+#define STEPCONFIG_YPP BIT(7)
+#define STEPCONFIG_YNN BIT(8)
+#define STEPCONFIG_XNP BIT(9)
+#define STEPCONFIG_YPN BIT(10)
+#define STEPCONFIG_INM_MASK (0xF << 15)
+#define STEPCONFIG_INM(val) ((val) << 15)
+#define STEPCONFIG_INM_ADCREFM STEPCONFIG_INM(8)
+#define STEPCONFIG_INP_MASK (0xF << 19)
+#define STEPCONFIG_INP(val) ((val) << 19)
+#define STEPCONFIG_INP_AN2 STEPCONFIG_INP(2)
+#define STEPCONFIG_INP_AN3 STEPCONFIG_INP(3)
+#define STEPCONFIG_INP_AN4 STEPCONFIG_INP(4)
+#define STEPCONFIG_INP_ADCREFM STEPCONFIG_INP(8)
+#define STEPCONFIG_FIFO1 BIT(26)
+
+/* Delay register */
+#define STEPDELAY_OPEN_MASK (0x3FFFF << 0)
+#define STEPDELAY_OPEN(val) ((val) << 0)
+#define STEPCONFIG_OPENDLY STEPDELAY_OPEN(0x098)
+#define STEPDELAY_SAMPLE_MASK (0xFF << 24)
+#define STEPDELAY_SAMPLE(val) ((val) << 24)
+#define STEPCONFIG_SAMPLEDLY STEPDELAY_SAMPLE(0)
+
+/* Charge Config */
+#define STEPCHARGE_RFP_MASK (7 << 12)
+#define STEPCHARGE_RFP(val) ((val) << 12)
+#define STEPCHARGE_RFP_XPUL STEPCHARGE_RFP(1)
+#define STEPCHARGE_INM_MASK (0xF << 15)
+#define STEPCHARGE_INM(val) ((val) << 15)
+#define STEPCHARGE_INM_AN1 STEPCHARGE_INM(1)
+#define STEPCHARGE_INP_MASK (0xF << 19)
+#define STEPCHARGE_INP(val) ((val) << 19)
+#define STEPCHARGE_INP_AN1 STEPCHARGE_INP(1)
+#define STEPCHARGE_RFM_MASK (3 << 23)
+#define STEPCHARGE_RFM(val) ((val) << 23)
+#define STEPCHARGE_RFM_XNUR STEPCHARGE_RFM(1)
+
+/* Charge delay */
+#define CHARGEDLY_OPEN_MASK (0x3FFFF << 0)
+#define CHARGEDLY_OPEN(val) ((val) << 0)
+#define CHARGEDLY_OPENDLY CHARGEDLY_OPEN(1)
+
+/* Control register */
+#define CNTRLREG_TSCSSENB BIT(0)
+#define CNTRLREG_STEPID BIT(1)
+#define CNTRLREG_STEPCONFIGWRT BIT(2)
+#define CNTRLREG_POWERDOWN BIT(4)
+#define CNTRLREG_AFE_CTRL_MASK (3 << 5)
+#define CNTRLREG_AFE_CTRL(val) ((val) << 5)
+#define CNTRLREG_4WIRE CNTRLREG_AFE_CTRL(1)
+#define CNTRLREG_5WIRE CNTRLREG_AFE_CTRL(2)
+#define CNTRLREG_8WIRE CNTRLREG_AFE_CTRL(3)
+#define CNTRLREG_TSCENB BIT(7)
+
+#define ADC_CLK 3000000
+#define MAX_CLK_DIV 7
+
+#define TSCADC_CELLS 0
+
+struct mfd_tscadc_board {
+ struct tsc_data *tsc_init;
+};
+
+struct ti_tscadc_dev {
+ struct device *dev;
+ struct regmap *regmap_tscadc;
+ void __iomem *tscadc_base;
+ int irq;
+ struct mfd_cell cells[TSCADC_CELLS];
+};
+
+#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 3/4] input: TSC: ti_tsc: Convert TSC into a MFDevice
2012-10-05 7:34 ` Patil, Rachna
@ 2012-10-05 7:34 ` Patil, Rachna
-1 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
This patch converts touchscreen into a MFD client.
All the register definitions, clock initialization,
etc has been moved to MFD core driver.
Signed-off-by: Patil, Rachna <rachna@ti.com>
---
Changes in v2:
No changes
Changes in v3:
No changes
Changes in v4:
No changes
Changes in v5:
No changes
drivers/input/touchscreen/Kconfig | 2 +-
drivers/input/touchscreen/ti_am335x_tsc.c | 318 +++++++++--------------------
drivers/mfd/ti_am335x_tscadc.c | 11 +
include/linux/mfd/ti_am335x_tscadc.h | 10 +-
4 files changed, 118 insertions(+), 223 deletions(-)
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 7bdb629..89a0492 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -531,7 +531,7 @@ config TOUCHSCREEN_TOUCHWIN
config TOUCHSCREEN_TI_AM335X_TSC
tristate "TI Touchscreen Interface"
- depends on ARCH_OMAP2PLUS
+ depends on MFD_TI_AM335X_TSCADC
help
Say Y here if you have 4/5/8 wire touchscreen controller
to be connected to the ADC controller on your TI AM335x SoC.
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 462950a..7a18a8a 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -27,106 +27,15 @@
#include <linux/input/ti_am335x_tsc.h>
#include <linux/delay.h>
-#define REG_RAWIRQSTATUS 0x024
-#define REG_IRQSTATUS 0x028
-#define REG_IRQENABLE 0x02C
-#define REG_IRQWAKEUP 0x034
-#define REG_CTRL 0x040
-#define REG_ADCFSM 0x044
-#define REG_CLKDIV 0x04C
-#define REG_SE 0x054
-#define REG_IDLECONFIG 0x058
-#define REG_CHARGECONFIG 0x05C
-#define REG_CHARGEDELAY 0x060
-#define REG_STEPCONFIG(n) (0x64 + ((n - 1) * 8))
-#define REG_STEPDELAY(n) (0x68 + ((n - 1) * 8))
-#define REG_FIFO0CNT 0xE4
-#define REG_FIFO0THR 0xE8
-#define REG_FIFO1THR 0xF4
-#define REG_FIFO0 0x100
-#define REG_FIFO1 0x200
-
-/* Register Bitfields */
-#define IRQWKUP_ENB BIT(0)
-
-/* Step Enable */
-#define STEPENB_MASK (0x1FFFF << 0)
-#define STEPENB(val) (val << 0)
-#define STPENB_STEPENB STEPENB(0x7FFF)
-
-/* IRQ enable */
-#define IRQENB_FIFO0THRES BIT(2)
-#define IRQENB_FIFO1THRES BIT(5)
-#define IRQENB_PENUP BIT(9)
-
-/* Step Configuration */
-#define STEPCONFIG_MODE_MASK (3 << 0)
-#define STEPCONFIG_MODE(val) (val << 0)
-#define STEPCONFIG_MODE_HWSYNC STEPCONFIG_MODE(2)
-#define STEPCONFIG_AVG_MASK (7 << 2)
-#define STEPCONFIG_AVG(val) (val << 2)
-#define STEPCONFIG_AVG_16 STEPCONFIG_AVG(4)
-#define STEPCONFIG_XPP BIT(5)
-#define STEPCONFIG_XNN BIT(6)
-#define STEPCONFIG_YPP BIT(7)
-#define STEPCONFIG_YNN BIT(8)
-#define STEPCONFIG_XNP BIT(9)
-#define STEPCONFIG_YPN BIT(10)
-#define STEPCONFIG_INM_MASK (0xF << 15)
-#define STEPCONFIG_INM(val) (val << 15)
-#define STEPCONFIG_INM_ADCREFM STEPCONFIG_INM(8)
-#define STEPCONFIG_INP_MASK (0xF << 19)
-#define STEPCONFIG_INP(val) (val << 19)
-#define STEPCONFIG_INP_AN2 STEPCONFIG_INP(2)
-#define STEPCONFIG_INP_AN3 STEPCONFIG_INP(3)
-#define STEPCONFIG_INP_AN4 STEPCONFIG_INP(4)
-#define STEPCONFIG_INP_ADCREFM STEPCONFIG_INP(8)
-#define STEPCONFIG_FIFO1 BIT(26)
-
-/* Delay register */
-#define STEPDELAY_OPEN_MASK (0x3FFFF << 0)
-#define STEPDELAY_OPEN(val) (val << 0)
-#define STEPCONFIG_OPENDLY STEPDELAY_OPEN(0x098)
-
-/* Charge Config */
-#define STEPCHARGE_RFP_MASK (7 << 12)
-#define STEPCHARGE_RFP(val) (val << 12)
-#define STEPCHARGE_RFP_XPUL STEPCHARGE_RFP(1)
-#define STEPCHARGE_INM_MASK (0xF << 15)
-#define STEPCHARGE_INM(val) (val << 15)
-#define STEPCHARGE_INM_AN1 STEPCHARGE_INM(1)
-#define STEPCHARGE_INP_MASK (0xF << 19)
-#define STEPCHARGE_INP(val) (val << 19)
-#define STEPCHARGE_INP_AN1 STEPCHARGE_INP(1)
-#define STEPCHARGE_RFM_MASK (3 << 23)
-#define STEPCHARGE_RFM(val) (val << 23)
-#define STEPCHARGE_RFM_XNUR STEPCHARGE_RFM(1)
-
-/* Charge delay */
-#define CHARGEDLY_OPEN_MASK (0x3FFFF << 0)
-#define CHARGEDLY_OPEN(val) (val << 0)
-#define CHARGEDLY_OPENDLY CHARGEDLY_OPEN(1)
-
-/* Control register */
-#define CNTRLREG_TSCSSENB BIT(0)
-#define CNTRLREG_STEPID BIT(1)
-#define CNTRLREG_STEPCONFIGWRT BIT(2)
-#define CNTRLREG_AFE_CTRL_MASK (3 << 5)
-#define CNTRLREG_AFE_CTRL(val) (val << 5)
-#define CNTRLREG_4WIRE CNTRLREG_AFE_CTRL(1)
-#define CNTRLREG_5WIRE CNTRLREG_AFE_CTRL(2)
-#define CNTRLREG_8WIRE CNTRLREG_AFE_CTRL(3)
-#define CNTRLREG_TSCENB BIT(7)
+#include <linux/mfd/ti_am335x_tscadc.h>
#define ADCFSM_STEPID 0x10
#define SEQ_SETTLE 275
-#define ADC_CLK 3000000
#define MAX_12BIT ((1 << 12) - 1)
struct titsc {
struct input_dev *input;
- struct clk *tsc_ick;
- void __iomem *tsc_base;
+ struct ti_tscadc_dev *mfd_tscadc;
unsigned int irq;
unsigned int wires;
unsigned int x_plate_resistance;
@@ -136,13 +45,13 @@ struct titsc {
static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
{
- return readl(ts->tsc_base + reg);
+ return readl(ts->mfd_tscadc->tscadc_base + reg);
}
static void titsc_writel(struct titsc *tsc, unsigned int reg,
unsigned int val)
{
- writel(val, tsc->tsc_base + reg);
+ writel(val, tsc->mfd_tscadc->tscadc_base + reg);
}
static void titsc_step_config(struct titsc *ts_dev)
@@ -219,17 +128,7 @@ static void titsc_step_config(struct titsc *ts_dev)
titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
STEPCONFIG_OPENDLY);
- titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
-}
-
-static void titsc_idle_config(struct titsc *ts_config)
-{
- unsigned int idleconfig;
-
- idleconfig = STEPCONFIG_YNN |
- STEPCONFIG_INM_ADCREFM |
- STEPCONFIG_YPN | STEPCONFIG_INP_ADCREFM;
- titsc_writel(ts_config, REG_IDLECONFIG, idleconfig);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB_TC);
}
static void titsc_read_coordinates(struct titsc *ts_dev,
@@ -239,7 +138,7 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
unsigned int prev_val_x = ~0, prev_val_y = ~0;
unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
unsigned int read, diff;
- unsigned int i;
+ unsigned int i, channel;
/*
* Delta filter is used to remove large variations in sampled
@@ -250,21 +149,32 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
* if true the value is reported to the sub system.
*/
for (i = 0; i < fifocount - 1; i++) {
- read = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
- diff = abs(read - prev_val_x);
- if (diff < prev_diff_x) {
- prev_diff_x = diff;
- *x = read;
+ read = titsc_readl(ts_dev, REG_FIFO0);
+ channel = read & 0xf0000;
+ channel = channel >> 0x10;
+ if ((channel >= 0) && (channel < ts_dev->steps_to_configure)) {
+ read &= 0xfff;
+ diff = abs(read - prev_val_x);
+ if (diff < prev_diff_x) {
+ prev_diff_x = diff;
+ *x = read;
+ }
+ prev_val_x = read;
}
- prev_val_x = read;
- read = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
- diff = abs(read - prev_val_y);
- if (diff < prev_diff_y) {
- prev_diff_y = diff;
- *y = read;
+ read = titsc_readl(ts_dev, REG_FIFO1);
+ channel = read & 0xf0000;
+ channel = channel >> 0x10;
+ if ((channel >= ts_dev->steps_to_configure) &&
+ (channel < (2 * ts_dev->steps_to_configure - 1))) {
+ read &= 0xfff;
+ diff = abs(read - prev_val_y);
+ if (diff < prev_diff_y) {
+ prev_diff_y = diff;
+ *y = read;
+ }
+ prev_val_y = read;
}
- prev_val_y = read;
}
}
@@ -276,6 +186,8 @@ static irqreturn_t titsc_irq(int irq, void *dev)
unsigned int x = 0, y = 0;
unsigned int z1, z2, z;
unsigned int fsm;
+ unsigned int fifo1count, fifo0count;
+ int i;
status = titsc_readl(ts_dev, REG_IRQSTATUS);
if (status & IRQENB_FIFO0THRES) {
@@ -284,6 +196,14 @@ static irqreturn_t titsc_irq(int irq, void *dev)
z1 = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
z2 = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
+ fifo1count = titsc_readl(ts_dev, REG_FIFO1CNT);
+ for (i = 0; i < fifo1count; i++)
+ titsc_readl(ts_dev, REG_FIFO1);
+
+ fifo0count = titsc_readl(ts_dev, REG_FIFO0CNT);
+ for (i = 0; i < fifo0count; i++)
+ titsc_readl(ts_dev, REG_FIFO0);
+
if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
/*
* Calculate pressure using formula
@@ -330,7 +250,7 @@ static irqreturn_t titsc_irq(int irq, void *dev)
titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
- titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB_TC);
return IRQ_HANDLED;
}
@@ -340,28 +260,16 @@ static irqreturn_t titsc_irq(int irq, void *dev)
static int __devinit titsc_probe(struct platform_device *pdev)
{
- const struct tsc_data *pdata = pdev->dev.platform_data;
- struct resource *res;
struct titsc *ts_dev;
struct input_dev *input_dev;
- struct clk *clk;
+ struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+ struct mfd_tscadc_board *pdata;
int err;
- int clk_value, ctrl, irq;
- if (!pdata) {
- dev_err(&pdev->dev, "missing platform data.\n");
- return -EINVAL;
- }
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "no memory resource defined.\n");
- return -EINVAL;
- }
+ pdata = tscadc_dev->dev->platform_data;
- irq = platform_get_irq(pdev, 0);
- if (irq < 0) {
- dev_err(&pdev->dev, "no irq ID is specified.\n");
+ if (!pdata) {
+ dev_err(&pdev->dev, "Could not find platform data\n");
return -EINVAL;
}
@@ -374,85 +282,26 @@ static int __devinit titsc_probe(struct platform_device *pdev)
goto err_free_mem;
}
+ tscadc_dev->tsc = ts_dev;
+ ts_dev->mfd_tscadc = tscadc_dev;
ts_dev->input = input_dev;
- ts_dev->irq = irq;
- ts_dev->wires = pdata->wires;
- ts_dev->x_plate_resistance = pdata->x_plate_resistance;
- ts_dev->steps_to_configure = pdata->steps_to_configure;
-
- res = request_mem_region(res->start, resource_size(res), pdev->name);
- if (!res) {
- dev_err(&pdev->dev, "failed to reserve registers.\n");
- err = -EBUSY;
- goto err_free_mem;
- }
-
- ts_dev->tsc_base = ioremap(res->start, resource_size(res));
- if (!ts_dev->tsc_base) {
- dev_err(&pdev->dev, "failed to map registers.\n");
- err = -ENOMEM;
- goto err_release_mem_region;
- }
+ ts_dev->irq = tscadc_dev->irq;
+ ts_dev->wires = pdata->tsc_init->wires;
+ ts_dev->x_plate_resistance = pdata->tsc_init->x_plate_resistance;
+ ts_dev->steps_to_configure = pdata->tsc_init->steps_to_configure;
err = request_irq(ts_dev->irq, titsc_irq,
0, pdev->dev.driver->name, ts_dev);
if (err) {
dev_err(&pdev->dev, "failed to allocate irq.\n");
- goto err_unmap_regs;
- }
-
- ts_dev->tsc_ick = clk_get(&pdev->dev, "adc_tsc_ick");
- if (IS_ERR(ts_dev->tsc_ick)) {
- dev_err(&pdev->dev, "failed to get TSC ick\n");
- goto err_free_irq;
- }
- clk_enable(ts_dev->tsc_ick);
-
- clk = clk_get(&pdev->dev, "adc_tsc_fck");
- if (IS_ERR(clk)) {
- dev_err(&pdev->dev, "failed to get TSC fck\n");
- err = PTR_ERR(clk);
- goto err_disable_clk;
- }
-
- clk_value = clk_get_rate(clk) / ADC_CLK;
- clk_put(clk);
-
- if (clk_value < 7) {
- dev_err(&pdev->dev, "clock input less than min clock requirement\n");
- goto err_disable_clk;
- }
- /* CLKDIV needs to be configured to the value minus 1 */
- titsc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
-
- /* Enable wake-up of the SoC using touchscreen */
- titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
-
- ctrl = CNTRLREG_STEPCONFIGWRT |
- CNTRLREG_TSCENB |
- CNTRLREG_STEPID;
- switch (ts_dev->wires) {
- case 4:
- ctrl |= CNTRLREG_4WIRE;
- break;
- case 5:
- ctrl |= CNTRLREG_5WIRE;
- break;
- case 8:
- ctrl |= CNTRLREG_8WIRE;
- break;
+ goto err_free_mem;
}
- titsc_writel(ts_dev, REG_CTRL, ctrl);
- titsc_idle_config(ts_dev);
titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
titsc_step_config(ts_dev);
titsc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
- ctrl |= CNTRLREG_TSCSSENB;
- titsc_writel(ts_dev, REG_CTRL, ctrl);
-
- input_dev->name = "ti-tsc-adc";
+ input_dev->name = "ti-tsc";
input_dev->dev.parent = &pdev->dev;
input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
@@ -465,20 +314,13 @@ static int __devinit titsc_probe(struct platform_device *pdev)
/* register to the input system */
err = input_register_device(input_dev);
if (err)
- goto err_disable_clk;
+ goto err_free_irq;
platform_set_drvdata(pdev, ts_dev);
return 0;
-err_disable_clk:
- clk_disable(ts_dev->tsc_ick);
- clk_put(ts_dev->tsc_ick);
err_free_irq:
free_irq(ts_dev->irq, ts_dev);
-err_unmap_regs:
- iounmap(ts_dev->tsc_base);
-err_release_mem_region:
- release_mem_region(res->start, resource_size(res));
err_free_mem:
input_free_device(input_dev);
kfree(ts_dev);
@@ -487,32 +329,66 @@ err_free_mem:
static int __devexit titsc_remove(struct platform_device *pdev)
{
- struct titsc *ts_dev = platform_get_drvdata(pdev);
- struct resource *res;
+ struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+ struct titsc *ts_dev = tscadc_dev->tsc;
free_irq(ts_dev->irq, ts_dev);
input_unregister_device(ts_dev->input);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- iounmap(ts_dev->tsc_base);
- release_mem_region(res->start, resource_size(res));
+ platform_set_drvdata(pdev, NULL);
+ kfree(ts_dev);
+ return 0;
+}
- clk_disable(ts_dev->tsc_ick);
- clk_put(ts_dev->tsc_ick);
+#ifdef CONFIG_PM
+static int titsc_suspend(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+ struct titsc *ts_dev = tscadc_dev->tsc;
+ unsigned int idle;
+
+ if (device_may_wakeup(tscadc_dev->dev)) {
+ idle = titsc_readl(ts_dev, REG_IRQENABLE);
+ titsc_writel(ts_dev, REG_IRQENABLE,
+ (idle | IRQENB_HW_PEN));
+ titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
+ }
+ return 0;
+}
- kfree(ts_dev);
+static int titsc_resume(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+ struct titsc *ts_dev = tscadc_dev->tsc;
- platform_set_drvdata(pdev, NULL);
+ if (device_may_wakeup(tscadc_dev->dev)) {
+ titsc_writel(ts_dev, REG_IRQWAKEUP,
+ 0x00);
+ titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
+ }
+ titsc_step_config(ts_dev);
+ titsc_writel(ts_dev, REG_FIFO0THR,
+ ts_dev->steps_to_configure);
return 0;
}
+static const struct dev_pm_ops titsc_pm_ops = {
+ .suspend = titsc_suspend,
+ .resume = titsc_resume,
+};
+#define TITSC_PM_OPS (&titsc_pm_ops)
+#else
+#define TITSC_PM_OPS NULL
+#endif
+
static struct platform_driver ti_tsc_driver = {
.probe = titsc_probe,
.remove = __devexit_p(titsc_remove),
.driver = {
.name = "tsc",
.owner = THIS_MODULE,
+ .pm = TITSC_PM_OPS,
},
};
module_platform_driver(ti_tsc_driver);
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
index 14df67b..d812be4 100644
--- a/drivers/mfd/ti_am335x_tscadc.c
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -24,6 +24,7 @@
#include <linux/pm_runtime.h>
#include <linux/mfd/ti_am335x_tscadc.h>
+#include <linux/input/ti_am335x_tsc.h>
static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
{
@@ -62,15 +63,19 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
struct resource *res;
struct clk *clk;
struct mfd_tscadc_board *pdata = pdev->dev.platform_data;
+ struct mfd_cell *cell;
int irq;
int err, ctrl;
int clk_value, clock_rate;
+ int tsc_wires;
if (!pdata) {
dev_err(&pdev->dev, "Could not find platform data\n");
return -EINVAL;
}
+ tsc_wires = pdata->tsc_init->wires;
+
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "no memory resource defined.\n");
@@ -161,6 +166,12 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
ctrl |= CNTRLREG_TSCSSENB;
tscadc_writel(tscadc, REG_CTRL, ctrl);
+ /* TSC Cell */
+ cell = &tscadc->cells[TSC_CELL];
+ cell->name = "tsc";
+ cell->platform_data = tscadc;
+ cell->pdata_size = sizeof(*tscadc);
+
err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
TSCADC_CELLS, NULL, 0, NULL);
if (err < 0)
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
index b7232b1..fc18b2e 100644
--- a/include/linux/mfd/ti_am335x_tscadc.h
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -47,6 +47,7 @@
#define STEPENB_MASK (0x1FFFF << 0)
#define STEPENB(val) ((val) << 0)
#define STPENB_STEPENB STEPENB(0x1FFFF)
+#define STPENB_STEPENB_TC STEPENB(0x1FFF)
/* IRQ enable */
#define IRQENB_HW_PEN BIT(0)
@@ -120,7 +121,11 @@
#define ADC_CLK 3000000
#define MAX_CLK_DIV 7
-#define TSCADC_CELLS 0
+#define TSCADC_CELLS 1
+
+enum tscadc_cells {
+ TSC_CELL,
+};
struct mfd_tscadc_board {
struct tsc_data *tsc_init;
@@ -132,6 +137,9 @@ struct ti_tscadc_dev {
void __iomem *tscadc_base;
int irq;
struct mfd_cell cells[TSCADC_CELLS];
+
+ /* tsc device */
+ struct titsc *tsc;
};
#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 3/4] input: TSC: ti_tsc: Convert TSC into a MFDevice
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
This patch converts touchscreen into a MFD client.
All the register definitions, clock initialization,
etc has been moved to MFD core driver.
Signed-off-by: Patil, Rachna <rachna@ti.com>
---
Changes in v2:
No changes
Changes in v3:
No changes
Changes in v4:
No changes
Changes in v5:
No changes
drivers/input/touchscreen/Kconfig | 2 +-
drivers/input/touchscreen/ti_am335x_tsc.c | 318 +++++++++--------------------
drivers/mfd/ti_am335x_tscadc.c | 11 +
include/linux/mfd/ti_am335x_tscadc.h | 10 +-
4 files changed, 118 insertions(+), 223 deletions(-)
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 7bdb629..89a0492 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -531,7 +531,7 @@ config TOUCHSCREEN_TOUCHWIN
config TOUCHSCREEN_TI_AM335X_TSC
tristate "TI Touchscreen Interface"
- depends on ARCH_OMAP2PLUS
+ depends on MFD_TI_AM335X_TSCADC
help
Say Y here if you have 4/5/8 wire touchscreen controller
to be connected to the ADC controller on your TI AM335x SoC.
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 462950a..7a18a8a 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -27,106 +27,15 @@
#include <linux/input/ti_am335x_tsc.h>
#include <linux/delay.h>
-#define REG_RAWIRQSTATUS 0x024
-#define REG_IRQSTATUS 0x028
-#define REG_IRQENABLE 0x02C
-#define REG_IRQWAKEUP 0x034
-#define REG_CTRL 0x040
-#define REG_ADCFSM 0x044
-#define REG_CLKDIV 0x04C
-#define REG_SE 0x054
-#define REG_IDLECONFIG 0x058
-#define REG_CHARGECONFIG 0x05C
-#define REG_CHARGEDELAY 0x060
-#define REG_STEPCONFIG(n) (0x64 + ((n - 1) * 8))
-#define REG_STEPDELAY(n) (0x68 + ((n - 1) * 8))
-#define REG_FIFO0CNT 0xE4
-#define REG_FIFO0THR 0xE8
-#define REG_FIFO1THR 0xF4
-#define REG_FIFO0 0x100
-#define REG_FIFO1 0x200
-
-/* Register Bitfields */
-#define IRQWKUP_ENB BIT(0)
-
-/* Step Enable */
-#define STEPENB_MASK (0x1FFFF << 0)
-#define STEPENB(val) (val << 0)
-#define STPENB_STEPENB STEPENB(0x7FFF)
-
-/* IRQ enable */
-#define IRQENB_FIFO0THRES BIT(2)
-#define IRQENB_FIFO1THRES BIT(5)
-#define IRQENB_PENUP BIT(9)
-
-/* Step Configuration */
-#define STEPCONFIG_MODE_MASK (3 << 0)
-#define STEPCONFIG_MODE(val) (val << 0)
-#define STEPCONFIG_MODE_HWSYNC STEPCONFIG_MODE(2)
-#define STEPCONFIG_AVG_MASK (7 << 2)
-#define STEPCONFIG_AVG(val) (val << 2)
-#define STEPCONFIG_AVG_16 STEPCONFIG_AVG(4)
-#define STEPCONFIG_XPP BIT(5)
-#define STEPCONFIG_XNN BIT(6)
-#define STEPCONFIG_YPP BIT(7)
-#define STEPCONFIG_YNN BIT(8)
-#define STEPCONFIG_XNP BIT(9)
-#define STEPCONFIG_YPN BIT(10)
-#define STEPCONFIG_INM_MASK (0xF << 15)
-#define STEPCONFIG_INM(val) (val << 15)
-#define STEPCONFIG_INM_ADCREFM STEPCONFIG_INM(8)
-#define STEPCONFIG_INP_MASK (0xF << 19)
-#define STEPCONFIG_INP(val) (val << 19)
-#define STEPCONFIG_INP_AN2 STEPCONFIG_INP(2)
-#define STEPCONFIG_INP_AN3 STEPCONFIG_INP(3)
-#define STEPCONFIG_INP_AN4 STEPCONFIG_INP(4)
-#define STEPCONFIG_INP_ADCREFM STEPCONFIG_INP(8)
-#define STEPCONFIG_FIFO1 BIT(26)
-
-/* Delay register */
-#define STEPDELAY_OPEN_MASK (0x3FFFF << 0)
-#define STEPDELAY_OPEN(val) (val << 0)
-#define STEPCONFIG_OPENDLY STEPDELAY_OPEN(0x098)
-
-/* Charge Config */
-#define STEPCHARGE_RFP_MASK (7 << 12)
-#define STEPCHARGE_RFP(val) (val << 12)
-#define STEPCHARGE_RFP_XPUL STEPCHARGE_RFP(1)
-#define STEPCHARGE_INM_MASK (0xF << 15)
-#define STEPCHARGE_INM(val) (val << 15)
-#define STEPCHARGE_INM_AN1 STEPCHARGE_INM(1)
-#define STEPCHARGE_INP_MASK (0xF << 19)
-#define STEPCHARGE_INP(val) (val << 19)
-#define STEPCHARGE_INP_AN1 STEPCHARGE_INP(1)
-#define STEPCHARGE_RFM_MASK (3 << 23)
-#define STEPCHARGE_RFM(val) (val << 23)
-#define STEPCHARGE_RFM_XNUR STEPCHARGE_RFM(1)
-
-/* Charge delay */
-#define CHARGEDLY_OPEN_MASK (0x3FFFF << 0)
-#define CHARGEDLY_OPEN(val) (val << 0)
-#define CHARGEDLY_OPENDLY CHARGEDLY_OPEN(1)
-
-/* Control register */
-#define CNTRLREG_TSCSSENB BIT(0)
-#define CNTRLREG_STEPID BIT(1)
-#define CNTRLREG_STEPCONFIGWRT BIT(2)
-#define CNTRLREG_AFE_CTRL_MASK (3 << 5)
-#define CNTRLREG_AFE_CTRL(val) (val << 5)
-#define CNTRLREG_4WIRE CNTRLREG_AFE_CTRL(1)
-#define CNTRLREG_5WIRE CNTRLREG_AFE_CTRL(2)
-#define CNTRLREG_8WIRE CNTRLREG_AFE_CTRL(3)
-#define CNTRLREG_TSCENB BIT(7)
+#include <linux/mfd/ti_am335x_tscadc.h>
#define ADCFSM_STEPID 0x10
#define SEQ_SETTLE 275
-#define ADC_CLK 3000000
#define MAX_12BIT ((1 << 12) - 1)
struct titsc {
struct input_dev *input;
- struct clk *tsc_ick;
- void __iomem *tsc_base;
+ struct ti_tscadc_dev *mfd_tscadc;
unsigned int irq;
unsigned int wires;
unsigned int x_plate_resistance;
@@ -136,13 +45,13 @@ struct titsc {
static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
{
- return readl(ts->tsc_base + reg);
+ return readl(ts->mfd_tscadc->tscadc_base + reg);
}
static void titsc_writel(struct titsc *tsc, unsigned int reg,
unsigned int val)
{
- writel(val, tsc->tsc_base + reg);
+ writel(val, tsc->mfd_tscadc->tscadc_base + reg);
}
static void titsc_step_config(struct titsc *ts_dev)
@@ -219,17 +128,7 @@ static void titsc_step_config(struct titsc *ts_dev)
titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
STEPCONFIG_OPENDLY);
- titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
-}
-
-static void titsc_idle_config(struct titsc *ts_config)
-{
- unsigned int idleconfig;
-
- idleconfig = STEPCONFIG_YNN |
- STEPCONFIG_INM_ADCREFM |
- STEPCONFIG_YPN | STEPCONFIG_INP_ADCREFM;
- titsc_writel(ts_config, REG_IDLECONFIG, idleconfig);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB_TC);
}
static void titsc_read_coordinates(struct titsc *ts_dev,
@@ -239,7 +138,7 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
unsigned int prev_val_x = ~0, prev_val_y = ~0;
unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
unsigned int read, diff;
- unsigned int i;
+ unsigned int i, channel;
/*
* Delta filter is used to remove large variations in sampled
@@ -250,21 +149,32 @@ static void titsc_read_coordinates(struct titsc *ts_dev,
* if true the value is reported to the sub system.
*/
for (i = 0; i < fifocount - 1; i++) {
- read = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
- diff = abs(read - prev_val_x);
- if (diff < prev_diff_x) {
- prev_diff_x = diff;
- *x = read;
+ read = titsc_readl(ts_dev, REG_FIFO0);
+ channel = read & 0xf0000;
+ channel = channel >> 0x10;
+ if ((channel >= 0) && (channel < ts_dev->steps_to_configure)) {
+ read &= 0xfff;
+ diff = abs(read - prev_val_x);
+ if (diff < prev_diff_x) {
+ prev_diff_x = diff;
+ *x = read;
+ }
+ prev_val_x = read;
}
- prev_val_x = read;
- read = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
- diff = abs(read - prev_val_y);
- if (diff < prev_diff_y) {
- prev_diff_y = diff;
- *y = read;
+ read = titsc_readl(ts_dev, REG_FIFO1);
+ channel = read & 0xf0000;
+ channel = channel >> 0x10;
+ if ((channel >= ts_dev->steps_to_configure) &&
+ (channel < (2 * ts_dev->steps_to_configure - 1))) {
+ read &= 0xfff;
+ diff = abs(read - prev_val_y);
+ if (diff < prev_diff_y) {
+ prev_diff_y = diff;
+ *y = read;
+ }
+ prev_val_y = read;
}
- prev_val_y = read;
}
}
@@ -276,6 +186,8 @@ static irqreturn_t titsc_irq(int irq, void *dev)
unsigned int x = 0, y = 0;
unsigned int z1, z2, z;
unsigned int fsm;
+ unsigned int fifo1count, fifo0count;
+ int i;
status = titsc_readl(ts_dev, REG_IRQSTATUS);
if (status & IRQENB_FIFO0THRES) {
@@ -284,6 +196,14 @@ static irqreturn_t titsc_irq(int irq, void *dev)
z1 = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
z2 = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
+ fifo1count = titsc_readl(ts_dev, REG_FIFO1CNT);
+ for (i = 0; i < fifo1count; i++)
+ titsc_readl(ts_dev, REG_FIFO1);
+
+ fifo0count = titsc_readl(ts_dev, REG_FIFO0CNT);
+ for (i = 0; i < fifo0count; i++)
+ titsc_readl(ts_dev, REG_FIFO0);
+
if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
/*
* Calculate pressure using formula
@@ -330,7 +250,7 @@ static irqreturn_t titsc_irq(int irq, void *dev)
titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
- titsc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+ titsc_writel(ts_dev, REG_SE, STPENB_STEPENB_TC);
return IRQ_HANDLED;
}
@@ -340,28 +260,16 @@ static irqreturn_t titsc_irq(int irq, void *dev)
static int __devinit titsc_probe(struct platform_device *pdev)
{
- const struct tsc_data *pdata = pdev->dev.platform_data;
- struct resource *res;
struct titsc *ts_dev;
struct input_dev *input_dev;
- struct clk *clk;
+ struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+ struct mfd_tscadc_board *pdata;
int err;
- int clk_value, ctrl, irq;
- if (!pdata) {
- dev_err(&pdev->dev, "missing platform data.\n");
- return -EINVAL;
- }
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "no memory resource defined.\n");
- return -EINVAL;
- }
+ pdata = tscadc_dev->dev->platform_data;
- irq = platform_get_irq(pdev, 0);
- if (irq < 0) {
- dev_err(&pdev->dev, "no irq ID is specified.\n");
+ if (!pdata) {
+ dev_err(&pdev->dev, "Could not find platform data\n");
return -EINVAL;
}
@@ -374,85 +282,26 @@ static int __devinit titsc_probe(struct platform_device *pdev)
goto err_free_mem;
}
+ tscadc_dev->tsc = ts_dev;
+ ts_dev->mfd_tscadc = tscadc_dev;
ts_dev->input = input_dev;
- ts_dev->irq = irq;
- ts_dev->wires = pdata->wires;
- ts_dev->x_plate_resistance = pdata->x_plate_resistance;
- ts_dev->steps_to_configure = pdata->steps_to_configure;
-
- res = request_mem_region(res->start, resource_size(res), pdev->name);
- if (!res) {
- dev_err(&pdev->dev, "failed to reserve registers.\n");
- err = -EBUSY;
- goto err_free_mem;
- }
-
- ts_dev->tsc_base = ioremap(res->start, resource_size(res));
- if (!ts_dev->tsc_base) {
- dev_err(&pdev->dev, "failed to map registers.\n");
- err = -ENOMEM;
- goto err_release_mem_region;
- }
+ ts_dev->irq = tscadc_dev->irq;
+ ts_dev->wires = pdata->tsc_init->wires;
+ ts_dev->x_plate_resistance = pdata->tsc_init->x_plate_resistance;
+ ts_dev->steps_to_configure = pdata->tsc_init->steps_to_configure;
err = request_irq(ts_dev->irq, titsc_irq,
0, pdev->dev.driver->name, ts_dev);
if (err) {
dev_err(&pdev->dev, "failed to allocate irq.\n");
- goto err_unmap_regs;
- }
-
- ts_dev->tsc_ick = clk_get(&pdev->dev, "adc_tsc_ick");
- if (IS_ERR(ts_dev->tsc_ick)) {
- dev_err(&pdev->dev, "failed to get TSC ick\n");
- goto err_free_irq;
- }
- clk_enable(ts_dev->tsc_ick);
-
- clk = clk_get(&pdev->dev, "adc_tsc_fck");
- if (IS_ERR(clk)) {
- dev_err(&pdev->dev, "failed to get TSC fck\n");
- err = PTR_ERR(clk);
- goto err_disable_clk;
- }
-
- clk_value = clk_get_rate(clk) / ADC_CLK;
- clk_put(clk);
-
- if (clk_value < 7) {
- dev_err(&pdev->dev, "clock input less than min clock requirement\n");
- goto err_disable_clk;
- }
- /* CLKDIV needs to be configured to the value minus 1 */
- titsc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
-
- /* Enable wake-up of the SoC using touchscreen */
- titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
-
- ctrl = CNTRLREG_STEPCONFIGWRT |
- CNTRLREG_TSCENB |
- CNTRLREG_STEPID;
- switch (ts_dev->wires) {
- case 4:
- ctrl |= CNTRLREG_4WIRE;
- break;
- case 5:
- ctrl |= CNTRLREG_5WIRE;
- break;
- case 8:
- ctrl |= CNTRLREG_8WIRE;
- break;
+ goto err_free_mem;
}
- titsc_writel(ts_dev, REG_CTRL, ctrl);
- titsc_idle_config(ts_dev);
titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
titsc_step_config(ts_dev);
titsc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
- ctrl |= CNTRLREG_TSCSSENB;
- titsc_writel(ts_dev, REG_CTRL, ctrl);
-
- input_dev->name = "ti-tsc-adc";
+ input_dev->name = "ti-tsc";
input_dev->dev.parent = &pdev->dev;
input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
@@ -465,20 +314,13 @@ static int __devinit titsc_probe(struct platform_device *pdev)
/* register to the input system */
err = input_register_device(input_dev);
if (err)
- goto err_disable_clk;
+ goto err_free_irq;
platform_set_drvdata(pdev, ts_dev);
return 0;
-err_disable_clk:
- clk_disable(ts_dev->tsc_ick);
- clk_put(ts_dev->tsc_ick);
err_free_irq:
free_irq(ts_dev->irq, ts_dev);
-err_unmap_regs:
- iounmap(ts_dev->tsc_base);
-err_release_mem_region:
- release_mem_region(res->start, resource_size(res));
err_free_mem:
input_free_device(input_dev);
kfree(ts_dev);
@@ -487,32 +329,66 @@ err_free_mem:
static int __devexit titsc_remove(struct platform_device *pdev)
{
- struct titsc *ts_dev = platform_get_drvdata(pdev);
- struct resource *res;
+ struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+ struct titsc *ts_dev = tscadc_dev->tsc;
free_irq(ts_dev->irq, ts_dev);
input_unregister_device(ts_dev->input);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- iounmap(ts_dev->tsc_base);
- release_mem_region(res->start, resource_size(res));
+ platform_set_drvdata(pdev, NULL);
+ kfree(ts_dev);
+ return 0;
+}
- clk_disable(ts_dev->tsc_ick);
- clk_put(ts_dev->tsc_ick);
+#ifdef CONFIG_PM
+static int titsc_suspend(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+ struct titsc *ts_dev = tscadc_dev->tsc;
+ unsigned int idle;
+
+ if (device_may_wakeup(tscadc_dev->dev)) {
+ idle = titsc_readl(ts_dev, REG_IRQENABLE);
+ titsc_writel(ts_dev, REG_IRQENABLE,
+ (idle | IRQENB_HW_PEN));
+ titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
+ }
+ return 0;
+}
- kfree(ts_dev);
+static int titsc_resume(struct device *dev)
+{
+ struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+ struct titsc *ts_dev = tscadc_dev->tsc;
- platform_set_drvdata(pdev, NULL);
+ if (device_may_wakeup(tscadc_dev->dev)) {
+ titsc_writel(ts_dev, REG_IRQWAKEUP,
+ 0x00);
+ titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
+ }
+ titsc_step_config(ts_dev);
+ titsc_writel(ts_dev, REG_FIFO0THR,
+ ts_dev->steps_to_configure);
return 0;
}
+static const struct dev_pm_ops titsc_pm_ops = {
+ .suspend = titsc_suspend,
+ .resume = titsc_resume,
+};
+#define TITSC_PM_OPS (&titsc_pm_ops)
+#else
+#define TITSC_PM_OPS NULL
+#endif
+
static struct platform_driver ti_tsc_driver = {
.probe = titsc_probe,
.remove = __devexit_p(titsc_remove),
.driver = {
.name = "tsc",
.owner = THIS_MODULE,
+ .pm = TITSC_PM_OPS,
},
};
module_platform_driver(ti_tsc_driver);
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
index 14df67b..d812be4 100644
--- a/drivers/mfd/ti_am335x_tscadc.c
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -24,6 +24,7 @@
#include <linux/pm_runtime.h>
#include <linux/mfd/ti_am335x_tscadc.h>
+#include <linux/input/ti_am335x_tsc.h>
static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
{
@@ -62,15 +63,19 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
struct resource *res;
struct clk *clk;
struct mfd_tscadc_board *pdata = pdev->dev.platform_data;
+ struct mfd_cell *cell;
int irq;
int err, ctrl;
int clk_value, clock_rate;
+ int tsc_wires;
if (!pdata) {
dev_err(&pdev->dev, "Could not find platform data\n");
return -EINVAL;
}
+ tsc_wires = pdata->tsc_init->wires;
+
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "no memory resource defined.\n");
@@ -161,6 +166,12 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
ctrl |= CNTRLREG_TSCSSENB;
tscadc_writel(tscadc, REG_CTRL, ctrl);
+ /* TSC Cell */
+ cell = &tscadc->cells[TSC_CELL];
+ cell->name = "tsc";
+ cell->platform_data = tscadc;
+ cell->pdata_size = sizeof(*tscadc);
+
err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
TSCADC_CELLS, NULL, 0, NULL);
if (err < 0)
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
index b7232b1..fc18b2e 100644
--- a/include/linux/mfd/ti_am335x_tscadc.h
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -47,6 +47,7 @@
#define STEPENB_MASK (0x1FFFF << 0)
#define STEPENB(val) ((val) << 0)
#define STPENB_STEPENB STEPENB(0x1FFFF)
+#define STPENB_STEPENB_TC STEPENB(0x1FFF)
/* IRQ enable */
#define IRQENB_HW_PEN BIT(0)
@@ -120,7 +121,11 @@
#define ADC_CLK 3000000
#define MAX_CLK_DIV 7
-#define TSCADC_CELLS 0
+#define TSCADC_CELLS 1
+
+enum tscadc_cells {
+ TSC_CELL,
+};
struct mfd_tscadc_board {
struct tsc_data *tsc_init;
@@ -132,6 +137,9 @@ struct ti_tscadc_dev {
void __iomem *tscadc_base;
int irq;
struct mfd_cell cells[TSCADC_CELLS];
+
+ /* tsc device */
+ struct titsc *tsc;
};
#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 4/4] IIO : ADC: tiadc: Add support of TI's ADC driver
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel, linux-input, linux-iio
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
This patch adds support for TI's ADC driver.
This is a multifunctional device.
Analog input lines are provided on which
voltage measurements can be carried out.
You can have upto 8 input lines.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
---
Changes in v2:
Addressed review comments from Matthias Kaehlcke
Changes in v3:
Addressed review comments from Jonathan Cameron.
Added comments, new line appropriately.
Changes in v4:
Removed extra comments and variables.
rename idev to indio_dev throughout the driver.
Renamed structs for better readability.
Changes in v5:
No changes
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/ti_am335x_adc.c | 260 +++++++++++++++++++++++++++
drivers/mfd/ti_am335x_tscadc.c | 18 ++-
include/linux/mfd/ti_am335x_tscadc.h | 9 +-
include/linux/platform_data/ti_am335x_adc.h | 14 ++
6 files changed, 307 insertions(+), 2 deletions(-)
create mode 100644 drivers/iio/adc/ti_am335x_adc.c
create mode 100644 include/linux/platform_data/ti_am335x_adc.h
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 8a78b4f..1372f7e 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -22,4 +22,11 @@ config AT91_ADC
help
Say yes here to build support for Atmel AT91 ADC.
+config TI_AM335X_ADC
+ tristate "TI's ADC driver"
+ depends on MFD_TI_AM335X_TSCADC
+ help
+ Say yes here to build support for Texas Instruments ADC
+ driver which is also a MFD client.
+
endmenu
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 52eec25..e716588 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -4,3 +4,4 @@
obj-$(CONFIG_AD7266) += ad7266.o
obj-$(CONFIG_AT91_ADC) += at91_adc.o
+obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
new file mode 100644
index 0000000..02a43c8
--- /dev/null
+++ b/drivers/iio/adc/ti_am335x_adc.c
@@ -0,0 +1,260 @@
+/*
+ * TI ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/iio/iio.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+#include <linux/platform_data/ti_am335x_adc.h>
+
+struct tiadc_device {
+ struct ti_tscadc_dev *mfd_tscadc;
+ int channels;
+};
+
+static unsigned int tiadc_readl(struct tiadc_device *adc, unsigned int reg)
+{
+ return readl(adc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void tiadc_writel(struct tiadc_device *adc, unsigned int reg,
+ unsigned int val)
+{
+ writel(val, adc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void tiadc_step_config(struct tiadc_device *adc_dev)
+{
+ unsigned int stepconfig;
+ int i, channels = 0, steps;
+
+ /*
+ * There are 16 configurable steps and 8 analog input
+ * lines available which are shared between Touchscreen and ADC.
+ *
+ * Steps backwards i.e. from 16 towards 0 are used by ADC
+ * depending on number of input lines needed.
+ * Channel would represent which analog input
+ * needs to be given to ADC to digitalize data.
+ */
+
+ steps = TOTAL_STEPS - adc_dev->channels;
+ channels = TOTAL_CHANNELS - adc_dev->channels;
+
+ stepconfig = STEPCONFIG_AVG_16 | STEPCONFIG_FIFO1;
+
+ for (i = (steps + 1); i <= TOTAL_STEPS; i++) {
+ tiadc_writel(adc_dev, REG_STEPCONFIG(i),
+ stepconfig | STEPCONFIG_INP(channels));
+ tiadc_writel(adc_dev, REG_STEPDELAY(i),
+ STEPCONFIG_OPENDLY);
+ channels++;
+ }
+ tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
+}
+
+static int tiadc_channel_init(struct iio_dev *indio_dev, int channels)
+{
+ struct iio_chan_spec *chan_array;
+ int i;
+
+ indio_dev->num_channels = channels;
+ chan_array = kcalloc(indio_dev->num_channels,
+ sizeof(struct iio_chan_spec), GFP_KERNEL);
+
+ if (chan_array == NULL)
+ return -ENOMEM;
+
+ for (i = 0; i < (indio_dev->num_channels); i++) {
+ struct iio_chan_spec *chan = chan_array + i;
+ chan->type = IIO_VOLTAGE;
+ chan->indexed = 1;
+ chan->channel = i;
+ chan->info_mask = IIO_CHAN_INFO_RAW_SEPARATE_BIT;
+ }
+
+ indio_dev->channels = chan_array;
+
+ return indio_dev->num_channels;
+}
+
+static void tiadc_channels_remove(struct iio_dev *indio_dev)
+{
+ kfree(indio_dev->channels);
+}
+
+static int tiadc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct tiadc_device *adc_dev = iio_priv(indio_dev);
+ int i;
+ unsigned int fifo1count, readx1;
+
+ /*
+ * When the sub-system is first enabled,
+ * the sequencer will always start with the
+ * lowest step (1) and continue until step (16).
+ * For ex: If we have enabled 4 ADC channels and
+ * currently use only 1 out of them, the
+ * sequencer still configures all the 4 steps,
+ * leading to 3 unwanted data.
+ * Hence we need to flush out this data.
+ */
+
+ fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
+ for (i = 0; i < fifo1count; i++) {
+ readx1 = tiadc_readl(adc_dev, REG_FIFO1);
+ if (i == chan->channel)
+ *val = readx1 & 0xfff;
+ }
+ tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
+
+ return IIO_VAL_INT;
+}
+
+static const struct iio_info tiadc_info = {
+ .read_raw = &tiadc_read_raw,
+};
+
+static int __devinit tiadc_probe(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev;
+ struct tiadc_device *adc_dev;
+ struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+ struct mfd_tscadc_board *pdata;
+ int err;
+
+ pdata = tscadc_dev->dev->platform_data;
+ if (!pdata || !pdata->adc_init) {
+ dev_err(&pdev->dev, "Could not find platform data\n");
+ return -EINVAL;
+ }
+
+ indio_dev = iio_device_alloc(sizeof(struct tiadc_device));
+ if (indio_dev == NULL) {
+ dev_err(&pdev->dev, "failed to allocate iio device\n");
+ err = -ENOMEM;
+ goto err_ret;
+ }
+ adc_dev = iio_priv(indio_dev);
+
+ adc_dev->mfd_tscadc = tscadc_dev;
+ adc_dev->channels = pdata->adc_init->adc_channels;
+
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->name = dev_name(&pdev->dev);
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &tiadc_info;
+
+ tiadc_step_config(adc_dev);
+
+ err = tiadc_channel_init(indio_dev, adc_dev->channels);
+ if (err < 0)
+ goto err_free_device;
+
+ err = iio_device_register(indio_dev);
+ if (err)
+ goto err_free_channels;
+
+ platform_set_drvdata(pdev, indio_dev);
+
+ return 0;
+
+err_free_channels:
+ tiadc_channels_remove(indio_dev);
+err_free_device:
+ iio_device_free(indio_dev);
+err_ret:
+ return err;
+}
+
+static int __devexit tiadc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+ iio_device_unregister(indio_dev);
+ tiadc_channels_remove(indio_dev);
+
+ iio_device_free(indio_dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int tiadc_suspend(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct tiadc_device *adc_dev = iio_priv(indio_dev);
+ struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+ unsigned int idle;
+
+ if (!device_may_wakeup(tscadc_dev->dev)) {
+ idle = tiadc_readl(adc_dev, REG_CTRL);
+ idle &= ~(CNTRLREG_TSCSSENB);
+ tiadc_writel(adc_dev, REG_CTRL, (idle |
+ CNTRLREG_POWERDOWN));
+ }
+
+ return 0;
+}
+
+static int tiadc_resume(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct tiadc_device *adc_dev = iio_priv(indio_dev);
+ unsigned int restore;
+
+ /* Make sure ADC is powered up */
+ restore = tiadc_readl(adc_dev, REG_CTRL);
+ restore &= ~(CNTRLREG_POWERDOWN);
+ tiadc_writel(adc_dev, REG_CTRL, restore);
+
+ tiadc_step_config(adc_dev);
+
+ return 0;
+}
+
+static const struct dev_pm_ops tiadc_pm_ops = {
+ .suspend = tiadc_suspend,
+ .resume = tiadc_resume,
+};
+#define TIADC_PM_OPS (&tiadc_pm_ops)
+#else
+#define TIADC_PM_OPS NULL
+#endif
+
+static struct platform_driver tiadc_driver = {
+ .driver = {
+ .name = "tiadc",
+ .owner = THIS_MODULE,
+ .pm = TIADC_PM_OPS,
+ },
+ .probe = tiadc_probe,
+ .remove = __devexit_p(tiadc_remove),
+};
+
+module_platform_driver(tiadc_driver);
+
+MODULE_DESCRIPTION("TI ADC controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
index d812be4..e947dd8 100644
--- a/drivers/mfd/ti_am335x_tscadc.c
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -25,6 +25,7 @@
#include <linux/mfd/ti_am335x_tscadc.h>
#include <linux/input/ti_am335x_tsc.h>
+#include <linux/platform_data/ti_am335x_adc.h>
static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
{
@@ -67,14 +68,23 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
int irq;
int err, ctrl;
int clk_value, clock_rate;
- int tsc_wires;
+ int tsc_wires, adc_channels = 0, total_channels;
if (!pdata) {
dev_err(&pdev->dev, "Could not find platform data\n");
return -EINVAL;
}
+ if (pdata->adc_init)
+ adc_channels = pdata->adc_init->adc_channels;
+
tsc_wires = pdata->tsc_init->wires;
+ total_channels = tsc_wires + adc_channels;
+
+ if (total_channels > 8) {
+ dev_err(&pdev->dev, "Number of i/p channels more than 8\n");
+ return -EINVAL;
+ }
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
@@ -172,6 +182,12 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
cell->platform_data = tscadc;
cell->pdata_size = sizeof(*tscadc);
+ /* ADC Cell */
+ cell = &tscadc->cells[ADC_CELL];
+ cell->name = "tiadc";
+ cell->platform_data = tscadc;
+ cell->pdata_size = sizeof(*tscadc);
+
err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
TSCADC_CELLS, NULL, 0, NULL);
if (err < 0)
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
index fc18b2e..c79ad5d 100644
--- a/include/linux/mfd/ti_am335x_tscadc.h
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -120,15 +120,19 @@
#define ADC_CLK 3000000
#define MAX_CLK_DIV 7
+#define TOTAL_STEPS 16
+#define TOTAL_CHANNELS 8
-#define TSCADC_CELLS 1
+#define TSCADC_CELLS 2
enum tscadc_cells {
TSC_CELL,
+ ADC_CELL,
};
struct mfd_tscadc_board {
struct tsc_data *tsc_init;
+ struct adc_data *adc_init;
};
struct ti_tscadc_dev {
@@ -140,6 +144,9 @@ struct ti_tscadc_dev {
/* tsc device */
struct titsc *tsc;
+
+ /* adc device */
+ struct adc_device *adc;
};
#endif
diff --git a/include/linux/platform_data/ti_am335x_adc.h b/include/linux/platform_data/ti_am335x_adc.h
new file mode 100644
index 0000000..e41d583
--- /dev/null
+++ b/include/linux/platform_data/ti_am335x_adc.h
@@ -0,0 +1,14 @@
+#ifndef __LINUX_TI_AM335X_ADC_H
+#define __LINUX_TI_AM335X_ADC_H
+
+/**
+ * struct adc_data ADC Input information
+ * @adc_channels: Number of analog inputs
+ * available for ADC.
+ */
+
+struct adc_data {
+ unsigned int adc_channels;
+};
+
+#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v5 4/4] IIO : ADC: tiadc: Add support of TI's ADC driver
@ 2012-10-05 7:34 ` Patil, Rachna
0 siblings, 0 replies; 12+ messages in thread
From: Patil, Rachna @ 2012-10-05 7:34 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA
Cc: Samuel Ortiz, Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron,
Patil, Rachna
This patch adds support for TI's ADC driver.
This is a multifunctional device.
Analog input lines are provided on which
voltage measurements can be carried out.
You can have upto 8 input lines.
Signed-off-by: Patil, Rachna <rachna-l0cyMroinI0@public.gmane.org>
Acked-by: Jonathan Cameron <jic23-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
Changes in v2:
Addressed review comments from Matthias Kaehlcke
Changes in v3:
Addressed review comments from Jonathan Cameron.
Added comments, new line appropriately.
Changes in v4:
Removed extra comments and variables.
rename idev to indio_dev throughout the driver.
Renamed structs for better readability.
Changes in v5:
No changes
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/ti_am335x_adc.c | 260 +++++++++++++++++++++++++++
drivers/mfd/ti_am335x_tscadc.c | 18 ++-
include/linux/mfd/ti_am335x_tscadc.h | 9 +-
include/linux/platform_data/ti_am335x_adc.h | 14 ++
6 files changed, 307 insertions(+), 2 deletions(-)
create mode 100644 drivers/iio/adc/ti_am335x_adc.c
create mode 100644 include/linux/platform_data/ti_am335x_adc.h
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 8a78b4f..1372f7e 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -22,4 +22,11 @@ config AT91_ADC
help
Say yes here to build support for Atmel AT91 ADC.
+config TI_AM335X_ADC
+ tristate "TI's ADC driver"
+ depends on MFD_TI_AM335X_TSCADC
+ help
+ Say yes here to build support for Texas Instruments ADC
+ driver which is also a MFD client.
+
endmenu
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 52eec25..e716588 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -4,3 +4,4 @@
obj-$(CONFIG_AD7266) += ad7266.o
obj-$(CONFIG_AT91_ADC) += at91_adc.o
+obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
new file mode 100644
index 0000000..02a43c8
--- /dev/null
+++ b/drivers/iio/adc/ti_am335x_adc.c
@@ -0,0 +1,260 @@
+/*
+ * TI ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/iio/iio.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+#include <linux/platform_data/ti_am335x_adc.h>
+
+struct tiadc_device {
+ struct ti_tscadc_dev *mfd_tscadc;
+ int channels;
+};
+
+static unsigned int tiadc_readl(struct tiadc_device *adc, unsigned int reg)
+{
+ return readl(adc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void tiadc_writel(struct tiadc_device *adc, unsigned int reg,
+ unsigned int val)
+{
+ writel(val, adc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void tiadc_step_config(struct tiadc_device *adc_dev)
+{
+ unsigned int stepconfig;
+ int i, channels = 0, steps;
+
+ /*
+ * There are 16 configurable steps and 8 analog input
+ * lines available which are shared between Touchscreen and ADC.
+ *
+ * Steps backwards i.e. from 16 towards 0 are used by ADC
+ * depending on number of input lines needed.
+ * Channel would represent which analog input
+ * needs to be given to ADC to digitalize data.
+ */
+
+ steps = TOTAL_STEPS - adc_dev->channels;
+ channels = TOTAL_CHANNELS - adc_dev->channels;
+
+ stepconfig = STEPCONFIG_AVG_16 | STEPCONFIG_FIFO1;
+
+ for (i = (steps + 1); i <= TOTAL_STEPS; i++) {
+ tiadc_writel(adc_dev, REG_STEPCONFIG(i),
+ stepconfig | STEPCONFIG_INP(channels));
+ tiadc_writel(adc_dev, REG_STEPDELAY(i),
+ STEPCONFIG_OPENDLY);
+ channels++;
+ }
+ tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
+}
+
+static int tiadc_channel_init(struct iio_dev *indio_dev, int channels)
+{
+ struct iio_chan_spec *chan_array;
+ int i;
+
+ indio_dev->num_channels = channels;
+ chan_array = kcalloc(indio_dev->num_channels,
+ sizeof(struct iio_chan_spec), GFP_KERNEL);
+
+ if (chan_array == NULL)
+ return -ENOMEM;
+
+ for (i = 0; i < (indio_dev->num_channels); i++) {
+ struct iio_chan_spec *chan = chan_array + i;
+ chan->type = IIO_VOLTAGE;
+ chan->indexed = 1;
+ chan->channel = i;
+ chan->info_mask = IIO_CHAN_INFO_RAW_SEPARATE_BIT;
+ }
+
+ indio_dev->channels = chan_array;
+
+ return indio_dev->num_channels;
+}
+
+static void tiadc_channels_remove(struct iio_dev *indio_dev)
+{
+ kfree(indio_dev->channels);
+}
+
+static int tiadc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct tiadc_device *adc_dev = iio_priv(indio_dev);
+ int i;
+ unsigned int fifo1count, readx1;
+
+ /*
+ * When the sub-system is first enabled,
+ * the sequencer will always start with the
+ * lowest step (1) and continue until step (16).
+ * For ex: If we have enabled 4 ADC channels and
+ * currently use only 1 out of them, the
+ * sequencer still configures all the 4 steps,
+ * leading to 3 unwanted data.
+ * Hence we need to flush out this data.
+ */
+
+ fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
+ for (i = 0; i < fifo1count; i++) {
+ readx1 = tiadc_readl(adc_dev, REG_FIFO1);
+ if (i == chan->channel)
+ *val = readx1 & 0xfff;
+ }
+ tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
+
+ return IIO_VAL_INT;
+}
+
+static const struct iio_info tiadc_info = {
+ .read_raw = &tiadc_read_raw,
+};
+
+static int __devinit tiadc_probe(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev;
+ struct tiadc_device *adc_dev;
+ struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+ struct mfd_tscadc_board *pdata;
+ int err;
+
+ pdata = tscadc_dev->dev->platform_data;
+ if (!pdata || !pdata->adc_init) {
+ dev_err(&pdev->dev, "Could not find platform data\n");
+ return -EINVAL;
+ }
+
+ indio_dev = iio_device_alloc(sizeof(struct tiadc_device));
+ if (indio_dev == NULL) {
+ dev_err(&pdev->dev, "failed to allocate iio device\n");
+ err = -ENOMEM;
+ goto err_ret;
+ }
+ adc_dev = iio_priv(indio_dev);
+
+ adc_dev->mfd_tscadc = tscadc_dev;
+ adc_dev->channels = pdata->adc_init->adc_channels;
+
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->name = dev_name(&pdev->dev);
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &tiadc_info;
+
+ tiadc_step_config(adc_dev);
+
+ err = tiadc_channel_init(indio_dev, adc_dev->channels);
+ if (err < 0)
+ goto err_free_device;
+
+ err = iio_device_register(indio_dev);
+ if (err)
+ goto err_free_channels;
+
+ platform_set_drvdata(pdev, indio_dev);
+
+ return 0;
+
+err_free_channels:
+ tiadc_channels_remove(indio_dev);
+err_free_device:
+ iio_device_free(indio_dev);
+err_ret:
+ return err;
+}
+
+static int __devexit tiadc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+ iio_device_unregister(indio_dev);
+ tiadc_channels_remove(indio_dev);
+
+ iio_device_free(indio_dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int tiadc_suspend(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct tiadc_device *adc_dev = iio_priv(indio_dev);
+ struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+ unsigned int idle;
+
+ if (!device_may_wakeup(tscadc_dev->dev)) {
+ idle = tiadc_readl(adc_dev, REG_CTRL);
+ idle &= ~(CNTRLREG_TSCSSENB);
+ tiadc_writel(adc_dev, REG_CTRL, (idle |
+ CNTRLREG_POWERDOWN));
+ }
+
+ return 0;
+}
+
+static int tiadc_resume(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct tiadc_device *adc_dev = iio_priv(indio_dev);
+ unsigned int restore;
+
+ /* Make sure ADC is powered up */
+ restore = tiadc_readl(adc_dev, REG_CTRL);
+ restore &= ~(CNTRLREG_POWERDOWN);
+ tiadc_writel(adc_dev, REG_CTRL, restore);
+
+ tiadc_step_config(adc_dev);
+
+ return 0;
+}
+
+static const struct dev_pm_ops tiadc_pm_ops = {
+ .suspend = tiadc_suspend,
+ .resume = tiadc_resume,
+};
+#define TIADC_PM_OPS (&tiadc_pm_ops)
+#else
+#define TIADC_PM_OPS NULL
+#endif
+
+static struct platform_driver tiadc_driver = {
+ .driver = {
+ .name = "tiadc",
+ .owner = THIS_MODULE,
+ .pm = TIADC_PM_OPS,
+ },
+ .probe = tiadc_probe,
+ .remove = __devexit_p(tiadc_remove),
+};
+
+module_platform_driver(tiadc_driver);
+
+MODULE_DESCRIPTION("TI ADC controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna-l0cyMroinI0@public.gmane.org>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
index d812be4..e947dd8 100644
--- a/drivers/mfd/ti_am335x_tscadc.c
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -25,6 +25,7 @@
#include <linux/mfd/ti_am335x_tscadc.h>
#include <linux/input/ti_am335x_tsc.h>
+#include <linux/platform_data/ti_am335x_adc.h>
static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
{
@@ -67,14 +68,23 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
int irq;
int err, ctrl;
int clk_value, clock_rate;
- int tsc_wires;
+ int tsc_wires, adc_channels = 0, total_channels;
if (!pdata) {
dev_err(&pdev->dev, "Could not find platform data\n");
return -EINVAL;
}
+ if (pdata->adc_init)
+ adc_channels = pdata->adc_init->adc_channels;
+
tsc_wires = pdata->tsc_init->wires;
+ total_channels = tsc_wires + adc_channels;
+
+ if (total_channels > 8) {
+ dev_err(&pdev->dev, "Number of i/p channels more than 8\n");
+ return -EINVAL;
+ }
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
@@ -172,6 +182,12 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
cell->platform_data = tscadc;
cell->pdata_size = sizeof(*tscadc);
+ /* ADC Cell */
+ cell = &tscadc->cells[ADC_CELL];
+ cell->name = "tiadc";
+ cell->platform_data = tscadc;
+ cell->pdata_size = sizeof(*tscadc);
+
err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
TSCADC_CELLS, NULL, 0, NULL);
if (err < 0)
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
index fc18b2e..c79ad5d 100644
--- a/include/linux/mfd/ti_am335x_tscadc.h
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -120,15 +120,19 @@
#define ADC_CLK 3000000
#define MAX_CLK_DIV 7
+#define TOTAL_STEPS 16
+#define TOTAL_CHANNELS 8
-#define TSCADC_CELLS 1
+#define TSCADC_CELLS 2
enum tscadc_cells {
TSC_CELL,
+ ADC_CELL,
};
struct mfd_tscadc_board {
struct tsc_data *tsc_init;
+ struct adc_data *adc_init;
};
struct ti_tscadc_dev {
@@ -140,6 +144,9 @@ struct ti_tscadc_dev {
/* tsc device */
struct titsc *tsc;
+
+ /* adc device */
+ struct adc_device *adc;
};
#endif
diff --git a/include/linux/platform_data/ti_am335x_adc.h b/include/linux/platform_data/ti_am335x_adc.h
new file mode 100644
index 0000000..e41d583
--- /dev/null
+++ b/include/linux/platform_data/ti_am335x_adc.h
@@ -0,0 +1,14 @@
+#ifndef __LINUX_TI_AM335X_ADC_H
+#define __LINUX_TI_AM335X_ADC_H
+
+/**
+ * struct adc_data ADC Input information
+ * @adc_channels: Number of analog inputs
+ * available for ADC.
+ */
+
+struct adc_data {
+ unsigned int adc_channels;
+};
+
+#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v5 4/4] IIO : ADC: tiadc: Add support of TI's ADC driver
@ 2012-10-06 9:40 ` Jonathan Cameron
0 siblings, 0 replies; 12+ messages in thread
From: Jonathan Cameron @ 2012-10-06 9:40 UTC (permalink / raw)
To: Patil, Rachna
Cc: linux-kernel, linux-input, linux-iio, Samuel Ortiz,
Dmitry Torokhov, Dmitry Torokhov, Jonathan Cameron
On 10/05/2012 08:34 AM, Patil, Rachna wrote:
> This patch adds support for TI's ADC driver.
> This is a multifunctional device.
> Analog input lines are provided on which
> voltage measurements can be carried out.
> You can have upto 8 input lines.
>
> Signed-off-by: Patil, Rachna <rachna@ti.com>
> Acked-by: Jonathan Cameron <jic23@kernel.org>
I'll take this patch as soon as I know the mfd part
has been accepted (just in case any interfaces change!)
> ---
> Changes in v2:
> Addressed review comments from Matthias Kaehlcke
>
> Changes in v3:
> Addressed review comments from Jonathan Cameron.
> Added comments, new line appropriately.
>
> Changes in v4:
> Removed extra comments and variables.
> rename idev to indio_dev throughout the driver.
> Renamed structs for better readability.
>
> Changes in v5:
> No changes
>
> drivers/iio/adc/Kconfig | 7 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/ti_am335x_adc.c | 260 +++++++++++++++++++++++++++
> drivers/mfd/ti_am335x_tscadc.c | 18 ++-
> include/linux/mfd/ti_am335x_tscadc.h | 9 +-
> include/linux/platform_data/ti_am335x_adc.h | 14 ++
> 6 files changed, 307 insertions(+), 2 deletions(-)
> create mode 100644 drivers/iio/adc/ti_am335x_adc.c
> create mode 100644 include/linux/platform_data/ti_am335x_adc.h
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 8a78b4f..1372f7e 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -22,4 +22,11 @@ config AT91_ADC
> help
> Say yes here to build support for Atmel AT91 ADC.
>
> +config TI_AM335X_ADC
> + tristate "TI's ADC driver"
> + depends on MFD_TI_AM335X_TSCADC
> + help
> + Say yes here to build support for Texas Instruments ADC
> + driver which is also a MFD client.
> +
> endmenu
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 52eec25..e716588 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -4,3 +4,4 @@
>
> obj-$(CONFIG_AD7266) += ad7266.o
> obj-$(CONFIG_AT91_ADC) += at91_adc.o
> +obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
> diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
> new file mode 100644
> index 0000000..02a43c8
> --- /dev/null
> +++ b/drivers/iio/adc/ti_am335x_adc.c
> @@ -0,0 +1,260 @@
> +/*
> + * TI ADC MFD driver
> + *
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/err.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/iio/iio.h>
> +
> +#include <linux/mfd/ti_am335x_tscadc.h>
> +#include <linux/platform_data/ti_am335x_adc.h>
> +
> +struct tiadc_device {
> + struct ti_tscadc_dev *mfd_tscadc;
> + int channels;
> +};
> +
> +static unsigned int tiadc_readl(struct tiadc_device *adc, unsigned int reg)
> +{
> + return readl(adc->mfd_tscadc->tscadc_base + reg);
> +}
> +
> +static void tiadc_writel(struct tiadc_device *adc, unsigned int reg,
> + unsigned int val)
> +{
> + writel(val, adc->mfd_tscadc->tscadc_base + reg);
> +}
> +
> +static void tiadc_step_config(struct tiadc_device *adc_dev)
> +{
> + unsigned int stepconfig;
> + int i, channels = 0, steps;
> +
> + /*
> + * There are 16 configurable steps and 8 analog input
> + * lines available which are shared between Touchscreen and ADC.
> + *
> + * Steps backwards i.e. from 16 towards 0 are used by ADC
> + * depending on number of input lines needed.
> + * Channel would represent which analog input
> + * needs to be given to ADC to digitalize data.
> + */
> +
> + steps = TOTAL_STEPS - adc_dev->channels;
> + channels = TOTAL_CHANNELS - adc_dev->channels;
> +
> + stepconfig = STEPCONFIG_AVG_16 | STEPCONFIG_FIFO1;
> +
> + for (i = (steps + 1); i <= TOTAL_STEPS; i++) {
> + tiadc_writel(adc_dev, REG_STEPCONFIG(i),
> + stepconfig | STEPCONFIG_INP(channels));
> + tiadc_writel(adc_dev, REG_STEPDELAY(i),
> + STEPCONFIG_OPENDLY);
> + channels++;
> + }
> + tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
> +}
> +
> +static int tiadc_channel_init(struct iio_dev *indio_dev, int channels)
> +{
> + struct iio_chan_spec *chan_array;
> + int i;
> +
> + indio_dev->num_channels = channels;
> + chan_array = kcalloc(indio_dev->num_channels,
> + sizeof(struct iio_chan_spec), GFP_KERNEL);
> +
> + if (chan_array == NULL)
> + return -ENOMEM;
> +
> + for (i = 0; i < (indio_dev->num_channels); i++) {
> + struct iio_chan_spec *chan = chan_array + i;
> + chan->type = IIO_VOLTAGE;
> + chan->indexed = 1;
> + chan->channel = i;
> + chan->info_mask = IIO_CHAN_INFO_RAW_SEPARATE_BIT;
> + }
> +
> + indio_dev->channels = chan_array;
> +
> + return indio_dev->num_channels;
> +}
> +
> +static void tiadc_channels_remove(struct iio_dev *indio_dev)
> +{
> + kfree(indio_dev->channels);
> +}
> +
> +static int tiadc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct tiadc_device *adc_dev = iio_priv(indio_dev);
> + int i;
> + unsigned int fifo1count, readx1;
> +
> + /*
> + * When the sub-system is first enabled,
> + * the sequencer will always start with the
> + * lowest step (1) and continue until step (16).
> + * For ex: If we have enabled 4 ADC channels and
> + * currently use only 1 out of them, the
> + * sequencer still configures all the 4 steps,
> + * leading to 3 unwanted data.
> + * Hence we need to flush out this data.
> + */
> +
> + fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
> + for (i = 0; i < fifo1count; i++) {
> + readx1 = tiadc_readl(adc_dev, REG_FIFO1);
> + if (i == chan->channel)
> + *val = readx1 & 0xfff;
> + }
> + tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
> +
> + return IIO_VAL_INT;
> +}
> +
> +static const struct iio_info tiadc_info = {
> + .read_raw = &tiadc_read_raw,
> +};
> +
> +static int __devinit tiadc_probe(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev;
> + struct tiadc_device *adc_dev;
> + struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
> + struct mfd_tscadc_board *pdata;
> + int err;
> +
> + pdata = tscadc_dev->dev->platform_data;
> + if (!pdata || !pdata->adc_init) {
> + dev_err(&pdev->dev, "Could not find platform data\n");
> + return -EINVAL;
> + }
> +
> + indio_dev = iio_device_alloc(sizeof(struct tiadc_device));
> + if (indio_dev == NULL) {
> + dev_err(&pdev->dev, "failed to allocate iio device\n");
> + err = -ENOMEM;
> + goto err_ret;
> + }
> + adc_dev = iio_priv(indio_dev);
> +
> + adc_dev->mfd_tscadc = tscadc_dev;
> + adc_dev->channels = pdata->adc_init->adc_channels;
> +
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->name = dev_name(&pdev->dev);
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &tiadc_info;
> +
> + tiadc_step_config(adc_dev);
> +
> + err = tiadc_channel_init(indio_dev, adc_dev->channels);
> + if (err < 0)
> + goto err_free_device;
> +
> + err = iio_device_register(indio_dev);
> + if (err)
> + goto err_free_channels;
> +
> + platform_set_drvdata(pdev, indio_dev);
> +
> + return 0;
> +
> +err_free_channels:
> + tiadc_channels_remove(indio_dev);
> +err_free_device:
> + iio_device_free(indio_dev);
> +err_ret:
> + return err;
> +}
> +
> +static int __devexit tiadc_remove(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> +
> + iio_device_unregister(indio_dev);
> + tiadc_channels_remove(indio_dev);
> +
> + iio_device_free(indio_dev);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int tiadc_suspend(struct device *dev)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tiadc_device *adc_dev = iio_priv(indio_dev);
> + struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
> + unsigned int idle;
> +
> + if (!device_may_wakeup(tscadc_dev->dev)) {
> + idle = tiadc_readl(adc_dev, REG_CTRL);
> + idle &= ~(CNTRLREG_TSCSSENB);
> + tiadc_writel(adc_dev, REG_CTRL, (idle |
> + CNTRLREG_POWERDOWN));
> + }
> +
> + return 0;
> +}
> +
> +static int tiadc_resume(struct device *dev)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tiadc_device *adc_dev = iio_priv(indio_dev);
> + unsigned int restore;
> +
> + /* Make sure ADC is powered up */
> + restore = tiadc_readl(adc_dev, REG_CTRL);
> + restore &= ~(CNTRLREG_POWERDOWN);
> + tiadc_writel(adc_dev, REG_CTRL, restore);
> +
> + tiadc_step_config(adc_dev);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops tiadc_pm_ops = {
> + .suspend = tiadc_suspend,
> + .resume = tiadc_resume,
> +};
> +#define TIADC_PM_OPS (&tiadc_pm_ops)
> +#else
> +#define TIADC_PM_OPS NULL
> +#endif
> +
> +static struct platform_driver tiadc_driver = {
> + .driver = {
> + .name = "tiadc",
> + .owner = THIS_MODULE,
> + .pm = TIADC_PM_OPS,
> + },
> + .probe = tiadc_probe,
> + .remove = __devexit_p(tiadc_remove),
> +};
> +
> +module_platform_driver(tiadc_driver);
> +
> +MODULE_DESCRIPTION("TI ADC controller driver");
> +MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
> index d812be4..e947dd8 100644
> --- a/drivers/mfd/ti_am335x_tscadc.c
> +++ b/drivers/mfd/ti_am335x_tscadc.c
> @@ -25,6 +25,7 @@
>
> #include <linux/mfd/ti_am335x_tscadc.h>
> #include <linux/input/ti_am335x_tsc.h>
> +#include <linux/platform_data/ti_am335x_adc.h>
>
> static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
> {
> @@ -67,14 +68,23 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
> int irq;
> int err, ctrl;
> int clk_value, clock_rate;
> - int tsc_wires;
> + int tsc_wires, adc_channels = 0, total_channels;
>
> if (!pdata) {
> dev_err(&pdev->dev, "Could not find platform data\n");
> return -EINVAL;
> }
>
> + if (pdata->adc_init)
> + adc_channels = pdata->adc_init->adc_channels;
> +
> tsc_wires = pdata->tsc_init->wires;
> + total_channels = tsc_wires + adc_channels;
> +
> + if (total_channels > 8) {
> + dev_err(&pdev->dev, "Number of i/p channels more than 8\n");
> + return -EINVAL;
> + }
>
> res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> if (!res) {
> @@ -172,6 +182,12 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
> cell->platform_data = tscadc;
> cell->pdata_size = sizeof(*tscadc);
>
> + /* ADC Cell */
> + cell = &tscadc->cells[ADC_CELL];
> + cell->name = "tiadc";
> + cell->platform_data = tscadc;
> + cell->pdata_size = sizeof(*tscadc);
> +
> err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
> TSCADC_CELLS, NULL, 0, NULL);
> if (err < 0)
> diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
> index fc18b2e..c79ad5d 100644
> --- a/include/linux/mfd/ti_am335x_tscadc.h
> +++ b/include/linux/mfd/ti_am335x_tscadc.h
> @@ -120,15 +120,19 @@
>
> #define ADC_CLK 3000000
> #define MAX_CLK_DIV 7
> +#define TOTAL_STEPS 16
> +#define TOTAL_CHANNELS 8
>
> -#define TSCADC_CELLS 1
> +#define TSCADC_CELLS 2
>
> enum tscadc_cells {
> TSC_CELL,
> + ADC_CELL,
> };
>
> struct mfd_tscadc_board {
> struct tsc_data *tsc_init;
> + struct adc_data *adc_init;
> };
>
> struct ti_tscadc_dev {
> @@ -140,6 +144,9 @@ struct ti_tscadc_dev {
>
> /* tsc device */
> struct titsc *tsc;
> +
> + /* adc device */
> + struct adc_device *adc;
> };
>
> #endif
> diff --git a/include/linux/platform_data/ti_am335x_adc.h b/include/linux/platform_data/ti_am335x_adc.h
> new file mode 100644
> index 0000000..e41d583
> --- /dev/null
> +++ b/include/linux/platform_data/ti_am335x_adc.h
> @@ -0,0 +1,14 @@
> +#ifndef __LINUX_TI_AM335X_ADC_H
> +#define __LINUX_TI_AM335X_ADC_H
> +
> +/**
> + * struct adc_data ADC Input information
> + * @adc_channels: Number of analog inputs
> + * available for ADC.
> + */
> +
> +struct adc_data {
> + unsigned int adc_channels;
> +};
> +
> +#endif
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v5 4/4] IIO : ADC: tiadc: Add support of TI's ADC driver
@ 2012-10-06 9:40 ` Jonathan Cameron
0 siblings, 0 replies; 12+ messages in thread
From: Jonathan Cameron @ 2012-10-06 9:40 UTC (permalink / raw)
To: Patil, Rachna
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Samuel Ortiz, Dmitry Torokhov,
Dmitry Torokhov, Jonathan Cameron
On 10/05/2012 08:34 AM, Patil, Rachna wrote:
> This patch adds support for TI's ADC driver.
> This is a multifunctional device.
> Analog input lines are provided on which
> voltage measurements can be carried out.
> You can have upto 8 input lines.
>
> Signed-off-by: Patil, Rachna <rachna-l0cyMroinI0@public.gmane.org>
> Acked-by: Jonathan Cameron <jic23-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
I'll take this patch as soon as I know the mfd part
has been accepted (just in case any interfaces change!)
> ---
> Changes in v2:
> Addressed review comments from Matthias Kaehlcke
>
> Changes in v3:
> Addressed review comments from Jonathan Cameron.
> Added comments, new line appropriately.
>
> Changes in v4:
> Removed extra comments and variables.
> rename idev to indio_dev throughout the driver.
> Renamed structs for better readability.
>
> Changes in v5:
> No changes
>
> drivers/iio/adc/Kconfig | 7 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/ti_am335x_adc.c | 260 +++++++++++++++++++++++++++
> drivers/mfd/ti_am335x_tscadc.c | 18 ++-
> include/linux/mfd/ti_am335x_tscadc.h | 9 +-
> include/linux/platform_data/ti_am335x_adc.h | 14 ++
> 6 files changed, 307 insertions(+), 2 deletions(-)
> create mode 100644 drivers/iio/adc/ti_am335x_adc.c
> create mode 100644 include/linux/platform_data/ti_am335x_adc.h
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 8a78b4f..1372f7e 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -22,4 +22,11 @@ config AT91_ADC
> help
> Say yes here to build support for Atmel AT91 ADC.
>
> +config TI_AM335X_ADC
> + tristate "TI's ADC driver"
> + depends on MFD_TI_AM335X_TSCADC
> + help
> + Say yes here to build support for Texas Instruments ADC
> + driver which is also a MFD client.
> +
> endmenu
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 52eec25..e716588 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -4,3 +4,4 @@
>
> obj-$(CONFIG_AD7266) += ad7266.o
> obj-$(CONFIG_AT91_ADC) += at91_adc.o
> +obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
> diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
> new file mode 100644
> index 0000000..02a43c8
> --- /dev/null
> +++ b/drivers/iio/adc/ti_am335x_adc.c
> @@ -0,0 +1,260 @@
> +/*
> + * TI ADC MFD driver
> + *
> + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/err.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/iio/iio.h>
> +
> +#include <linux/mfd/ti_am335x_tscadc.h>
> +#include <linux/platform_data/ti_am335x_adc.h>
> +
> +struct tiadc_device {
> + struct ti_tscadc_dev *mfd_tscadc;
> + int channels;
> +};
> +
> +static unsigned int tiadc_readl(struct tiadc_device *adc, unsigned int reg)
> +{
> + return readl(adc->mfd_tscadc->tscadc_base + reg);
> +}
> +
> +static void tiadc_writel(struct tiadc_device *adc, unsigned int reg,
> + unsigned int val)
> +{
> + writel(val, adc->mfd_tscadc->tscadc_base + reg);
> +}
> +
> +static void tiadc_step_config(struct tiadc_device *adc_dev)
> +{
> + unsigned int stepconfig;
> + int i, channels = 0, steps;
> +
> + /*
> + * There are 16 configurable steps and 8 analog input
> + * lines available which are shared between Touchscreen and ADC.
> + *
> + * Steps backwards i.e. from 16 towards 0 are used by ADC
> + * depending on number of input lines needed.
> + * Channel would represent which analog input
> + * needs to be given to ADC to digitalize data.
> + */
> +
> + steps = TOTAL_STEPS - adc_dev->channels;
> + channels = TOTAL_CHANNELS - adc_dev->channels;
> +
> + stepconfig = STEPCONFIG_AVG_16 | STEPCONFIG_FIFO1;
> +
> + for (i = (steps + 1); i <= TOTAL_STEPS; i++) {
> + tiadc_writel(adc_dev, REG_STEPCONFIG(i),
> + stepconfig | STEPCONFIG_INP(channels));
> + tiadc_writel(adc_dev, REG_STEPDELAY(i),
> + STEPCONFIG_OPENDLY);
> + channels++;
> + }
> + tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
> +}
> +
> +static int tiadc_channel_init(struct iio_dev *indio_dev, int channels)
> +{
> + struct iio_chan_spec *chan_array;
> + int i;
> +
> + indio_dev->num_channels = channels;
> + chan_array = kcalloc(indio_dev->num_channels,
> + sizeof(struct iio_chan_spec), GFP_KERNEL);
> +
> + if (chan_array == NULL)
> + return -ENOMEM;
> +
> + for (i = 0; i < (indio_dev->num_channels); i++) {
> + struct iio_chan_spec *chan = chan_array + i;
> + chan->type = IIO_VOLTAGE;
> + chan->indexed = 1;
> + chan->channel = i;
> + chan->info_mask = IIO_CHAN_INFO_RAW_SEPARATE_BIT;
> + }
> +
> + indio_dev->channels = chan_array;
> +
> + return indio_dev->num_channels;
> +}
> +
> +static void tiadc_channels_remove(struct iio_dev *indio_dev)
> +{
> + kfree(indio_dev->channels);
> +}
> +
> +static int tiadc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct tiadc_device *adc_dev = iio_priv(indio_dev);
> + int i;
> + unsigned int fifo1count, readx1;
> +
> + /*
> + * When the sub-system is first enabled,
> + * the sequencer will always start with the
> + * lowest step (1) and continue until step (16).
> + * For ex: If we have enabled 4 ADC channels and
> + * currently use only 1 out of them, the
> + * sequencer still configures all the 4 steps,
> + * leading to 3 unwanted data.
> + * Hence we need to flush out this data.
> + */
> +
> + fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
> + for (i = 0; i < fifo1count; i++) {
> + readx1 = tiadc_readl(adc_dev, REG_FIFO1);
> + if (i == chan->channel)
> + *val = readx1 & 0xfff;
> + }
> + tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
> +
> + return IIO_VAL_INT;
> +}
> +
> +static const struct iio_info tiadc_info = {
> + .read_raw = &tiadc_read_raw,
> +};
> +
> +static int __devinit tiadc_probe(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev;
> + struct tiadc_device *adc_dev;
> + struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
> + struct mfd_tscadc_board *pdata;
> + int err;
> +
> + pdata = tscadc_dev->dev->platform_data;
> + if (!pdata || !pdata->adc_init) {
> + dev_err(&pdev->dev, "Could not find platform data\n");
> + return -EINVAL;
> + }
> +
> + indio_dev = iio_device_alloc(sizeof(struct tiadc_device));
> + if (indio_dev == NULL) {
> + dev_err(&pdev->dev, "failed to allocate iio device\n");
> + err = -ENOMEM;
> + goto err_ret;
> + }
> + adc_dev = iio_priv(indio_dev);
> +
> + adc_dev->mfd_tscadc = tscadc_dev;
> + adc_dev->channels = pdata->adc_init->adc_channels;
> +
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->name = dev_name(&pdev->dev);
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &tiadc_info;
> +
> + tiadc_step_config(adc_dev);
> +
> + err = tiadc_channel_init(indio_dev, adc_dev->channels);
> + if (err < 0)
> + goto err_free_device;
> +
> + err = iio_device_register(indio_dev);
> + if (err)
> + goto err_free_channels;
> +
> + platform_set_drvdata(pdev, indio_dev);
> +
> + return 0;
> +
> +err_free_channels:
> + tiadc_channels_remove(indio_dev);
> +err_free_device:
> + iio_device_free(indio_dev);
> +err_ret:
> + return err;
> +}
> +
> +static int __devexit tiadc_remove(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> +
> + iio_device_unregister(indio_dev);
> + tiadc_channels_remove(indio_dev);
> +
> + iio_device_free(indio_dev);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int tiadc_suspend(struct device *dev)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tiadc_device *adc_dev = iio_priv(indio_dev);
> + struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
> + unsigned int idle;
> +
> + if (!device_may_wakeup(tscadc_dev->dev)) {
> + idle = tiadc_readl(adc_dev, REG_CTRL);
> + idle &= ~(CNTRLREG_TSCSSENB);
> + tiadc_writel(adc_dev, REG_CTRL, (idle |
> + CNTRLREG_POWERDOWN));
> + }
> +
> + return 0;
> +}
> +
> +static int tiadc_resume(struct device *dev)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tiadc_device *adc_dev = iio_priv(indio_dev);
> + unsigned int restore;
> +
> + /* Make sure ADC is powered up */
> + restore = tiadc_readl(adc_dev, REG_CTRL);
> + restore &= ~(CNTRLREG_POWERDOWN);
> + tiadc_writel(adc_dev, REG_CTRL, restore);
> +
> + tiadc_step_config(adc_dev);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops tiadc_pm_ops = {
> + .suspend = tiadc_suspend,
> + .resume = tiadc_resume,
> +};
> +#define TIADC_PM_OPS (&tiadc_pm_ops)
> +#else
> +#define TIADC_PM_OPS NULL
> +#endif
> +
> +static struct platform_driver tiadc_driver = {
> + .driver = {
> + .name = "tiadc",
> + .owner = THIS_MODULE,
> + .pm = TIADC_PM_OPS,
> + },
> + .probe = tiadc_probe,
> + .remove = __devexit_p(tiadc_remove),
> +};
> +
> +module_platform_driver(tiadc_driver);
> +
> +MODULE_DESCRIPTION("TI ADC controller driver");
> +MODULE_AUTHOR("Rachna Patil <rachna-l0cyMroinI0@public.gmane.org>");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
> index d812be4..e947dd8 100644
> --- a/drivers/mfd/ti_am335x_tscadc.c
> +++ b/drivers/mfd/ti_am335x_tscadc.c
> @@ -25,6 +25,7 @@
>
> #include <linux/mfd/ti_am335x_tscadc.h>
> #include <linux/input/ti_am335x_tsc.h>
> +#include <linux/platform_data/ti_am335x_adc.h>
>
> static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
> {
> @@ -67,14 +68,23 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
> int irq;
> int err, ctrl;
> int clk_value, clock_rate;
> - int tsc_wires;
> + int tsc_wires, adc_channels = 0, total_channels;
>
> if (!pdata) {
> dev_err(&pdev->dev, "Could not find platform data\n");
> return -EINVAL;
> }
>
> + if (pdata->adc_init)
> + adc_channels = pdata->adc_init->adc_channels;
> +
> tsc_wires = pdata->tsc_init->wires;
> + total_channels = tsc_wires + adc_channels;
> +
> + if (total_channels > 8) {
> + dev_err(&pdev->dev, "Number of i/p channels more than 8\n");
> + return -EINVAL;
> + }
>
> res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> if (!res) {
> @@ -172,6 +182,12 @@ static int __devinit ti_tscadc_probe(struct platform_device *pdev)
> cell->platform_data = tscadc;
> cell->pdata_size = sizeof(*tscadc);
>
> + /* ADC Cell */
> + cell = &tscadc->cells[ADC_CELL];
> + cell->name = "tiadc";
> + cell->platform_data = tscadc;
> + cell->pdata_size = sizeof(*tscadc);
> +
> err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
> TSCADC_CELLS, NULL, 0, NULL);
> if (err < 0)
> diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
> index fc18b2e..c79ad5d 100644
> --- a/include/linux/mfd/ti_am335x_tscadc.h
> +++ b/include/linux/mfd/ti_am335x_tscadc.h
> @@ -120,15 +120,19 @@
>
> #define ADC_CLK 3000000
> #define MAX_CLK_DIV 7
> +#define TOTAL_STEPS 16
> +#define TOTAL_CHANNELS 8
>
> -#define TSCADC_CELLS 1
> +#define TSCADC_CELLS 2
>
> enum tscadc_cells {
> TSC_CELL,
> + ADC_CELL,
> };
>
> struct mfd_tscadc_board {
> struct tsc_data *tsc_init;
> + struct adc_data *adc_init;
> };
>
> struct ti_tscadc_dev {
> @@ -140,6 +144,9 @@ struct ti_tscadc_dev {
>
> /* tsc device */
> struct titsc *tsc;
> +
> + /* adc device */
> + struct adc_device *adc;
> };
>
> #endif
> diff --git a/include/linux/platform_data/ti_am335x_adc.h b/include/linux/platform_data/ti_am335x_adc.h
> new file mode 100644
> index 0000000..e41d583
> --- /dev/null
> +++ b/include/linux/platform_data/ti_am335x_adc.h
> @@ -0,0 +1,14 @@
> +#ifndef __LINUX_TI_AM335X_ADC_H
> +#define __LINUX_TI_AM335X_ADC_H
> +
> +/**
> + * struct adc_data ADC Input information
> + * @adc_channels: Number of analog inputs
> + * available for ADC.
> + */
> +
> +struct adc_data {
> + unsigned int adc_channels;
> +};
> +
> +#endif
>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2012-10-06 9:40 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-10-05 7:34 [PATCH v5 0/4] Support for TSC/ADC MFD driver Patil, Rachna
2012-10-05 7:34 ` Patil, Rachna
2012-10-05 7:34 ` [PATCH v5 1/4] input: TSC: ti_tscadc: Rename the existing touchscreen driver Patil, Rachna
2012-10-05 7:34 ` Patil, Rachna
2012-10-05 7:34 ` [PATCH v5 2/4] MFD: ti_tscadc: Add support for TI's TSC/ADC MFDevice Patil, Rachna
2012-10-05 7:34 ` Patil, Rachna
2012-10-05 7:34 ` [PATCH v5 3/4] input: TSC: ti_tsc: Convert TSC into a MFDevice Patil, Rachna
2012-10-05 7:34 ` Patil, Rachna
2012-10-05 7:34 ` [PATCH v5 4/4] IIO : ADC: tiadc: Add support of TI's ADC driver Patil, Rachna
2012-10-05 7:34 ` Patil, Rachna
2012-10-06 9:40 ` Jonathan Cameron
2012-10-06 9:40 ` Jonathan Cameron
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.