[PATCH] SPI: New driver for SPI master controller for CLPS711X-target

[PATCH] SPI: New driver for SPI master controller for CLPS711X-target

[Alexander Shiyan]

This patch add new driver for CLPS711X SPI master controller.
Due to platform limitations driver supports only 8 bit transfer mode.
Chip select control is handled via GPIO.

Signed-off-by: Alexander Shiyan <shc_work-JGs/UdohzUI@public.gmane.org>
---
 drivers/spi/Kconfig                        |    7 +
 drivers/spi/Makefile                       |    1 +
 drivers/spi/spi-clps711x.c                 |  291 ++++++++++++++++++++++++++++
 include/linux/platform_data/spi-clps711x.h |   21 ++
 4 files changed, 320 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/spi-clps711x.c
 create mode 100644 include/linux/platform_data/spi-clps711x.h

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 1acae35..2a13e63 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -123,6 +123,13 @@ config SPI_BUTTERFLY
 	  inexpensive battery powered microcontroller evaluation board.
 	  This same cable can be used to flash new firmware.
 
+config SPI_CLPS711X
+	tristate "CLPS711X host SPI controller"
+	depends on ARCH_CLPS711X
+	help
+	  This enables dedicated general purpose SPI/Microwire1-compatible
+	  master mode interface (SSI1) for CLPS711X-based CPUs.
+
 config SPI_COLDFIRE_QSPI
 	tristate "Freescale Coldfire QSPI controller"
 	depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index c48df47..25ab4a1 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
 obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o
 obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
 obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
+obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
 obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
 obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
 obj-$(CONFIG_SPI_DESIGNWARE)		+= spi-dw.o
diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
new file mode 100644
index 0000000..2674678
--- /dev/null
+++ b/drivers/spi/spi-clps711x.c
@@ -0,0 +1,291 @@
+/*
+ *  CLPS711X SPI bus driver
+ *
+ *  Copyright (C) 2012 Alexander Shiyan <shc_work-JGs/UdohzUI@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/platform_data/spi-clps711x.h>
+
+#include <mach/hardware.h>
+
+#define DRIVER_NAME	"spi-clps711x"
+
+struct spi_clps711x_data {
+	struct completion	done;
+
+	struct clk		*spi_clk;
+	u32			max_speed_hz;
+
+	u8			*tx_buf;
+	u8			*rx_buf;
+	int			count;
+	int			len;
+
+	int			chipselect[0];
+};
+
+static int spi_clps711x_setup(struct spi_device *spi)
+{
+	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
+
+	if (spi->bits_per_word != 8) {
+		dev_err(&spi->dev, "Unsupported master bus width %i\n",
+			spi->bits_per_word);
+		return -EINVAL;
+	}
+
+	/* We are expect that SPI-device is not selected */
+	gpio_direction_output(hw->chipselect[spi->chip_select],
+			      !(spi->mode & SPI_CS_HIGH));
+
+	return 0;
+}
+
+static void spi_clps711x_setup_mode(struct spi_device *spi)
+{
+	/* Setup edge for transfer */
+	if (spi->mode & SPI_CPHA)
+		clps_writew(clps_readw(SYSCON3) | SYSCON3_ADCCKNSEN, SYSCON3);
+	else
+		clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
+}
+
+static int spi_clps711x_setup_xfer(struct spi_device *spi,
+				   struct spi_transfer *xfer)
+{
+	u32 speed = xfer->speed_hz ? : spi->max_speed_hz;
+	u8 bpw = xfer->bits_per_word ? : spi->bits_per_word;
+	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
+
+	if (bpw != 8) {
+		dev_err(&spi->dev, "Unsupported master bus width %i\n", bpw);
+		return -EINVAL;
+	}
+
+	/* Setup SPI frequency divider */
+	if (!speed || (speed >= hw->max_speed_hz))
+		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+			    SYSCON1_ADCKSEL(3), SYSCON1);
+	else if (speed >= (hw->max_speed_hz / 2))
+		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+			    SYSCON1_ADCKSEL(2), SYSCON1);
+	else if (speed >= (hw->max_speed_hz / 8))
+		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+			    SYSCON1_ADCKSEL(1), SYSCON1);
+	else
+		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+			    SYSCON1_ADCKSEL(0), SYSCON1);
+
+	return 0;
+}
+
+static int spi_clps711x_transfer_one_message(struct spi_master *master,
+					     struct spi_message *msg)
+{
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
+	struct spi_transfer *xfer;
+	int status = 0, cs = hw->chipselect[msg->spi->chip_select];
+	u32 data;
+
+	spi_clps711x_setup_mode(msg->spi);
+
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+		if (spi_clps711x_setup_xfer(msg->spi, xfer)) {
+			status = -EINVAL;
+			goto out_xfr;
+		}
+
+		gpio_set_value(cs, !!(msg->spi->mode & SPI_CS_HIGH));
+
+		INIT_COMPLETION(hw->done);
+
+		hw->count = 0;
+		hw->len = xfer->len;
+		hw->tx_buf = (u8 *)xfer->tx_buf;
+		hw->rx_buf = (u8 *)xfer->rx_buf;
+
+		/* Initiate transfer */
+		data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
+		clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
+
+		wait_for_completion(&hw->done);
+
+		if (xfer->delay_usecs)
+			udelay(xfer->delay_usecs);
+
+		if (xfer->cs_change ||
+		    list_is_last(&xfer->transfer_list, &msg->transfers))
+			gpio_set_value(cs, !(msg->spi->mode & SPI_CS_HIGH));
+
+		msg->actual_length += xfer->len;
+	}
+
+out_xfr:
+	msg->status = status;
+	spi_finalize_current_message(master);
+
+	return 0;
+}
+
+static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
+{
+	struct spi_clps711x_data *hw = (struct spi_clps711x_data *)dev_id;
+	u32 data;
+
+	/* Handle RX */
+	data = clps_readb(SYNCIO);
+	if (hw->rx_buf)
+		hw->rx_buf[hw->count] = (u8)data;
+
+	hw->count++;
+
+	/* Handle TX */
+	if (hw->count < hw->len) {
+		data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
+		clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
+	} else
+		complete(&hw->done);
+
+	return IRQ_HANDLED;
+}
+
+static int __devinit spi_clps711x_probe(struct platform_device *pdev)
+{
+	int i, ret;
+	struct spi_master *master;
+	struct spi_clps711x_data *hw;
+	struct spi_clps711x_pdata *pdata = dev_get_platdata(&pdev->dev);
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "No platform data supplied\n");
+		return -EINVAL;
+	}
+
+	master = spi_alloc_master(&pdev->dev,
+				  sizeof(struct spi_clps711x_data) +
+				  sizeof(int) * pdata->num_chipselect);
+	if (!master) {
+		dev_err(&pdev->dev, "SPI allocating memory error\n");
+		return -ENOMEM;
+	}
+
+	master->bus_num = pdev->id;
+	master->mode_bits = SPI_CPHA | SPI_CS_HIGH;
+	master->num_chipselect = pdata->num_chipselect;
+	master->setup = spi_clps711x_setup;
+	master->transfer_one_message = spi_clps711x_transfer_one_message;
+
+	hw = spi_master_get_devdata(master);
+
+	for (i = 0; i < master->num_chipselect; i++) {
+		hw->chipselect[i] = pdata->chipselect[i];
+		if (!gpio_is_valid(hw->chipselect[i])) {
+			dev_err(&pdev->dev, "Invalid CS GPIO %i\n", i);
+			ret = -EINVAL;
+			goto err_out;
+		}
+		if (gpio_request(hw->chipselect[i], DRIVER_NAME)) {
+			dev_err(&pdev->dev, "Can't get CS GPIO %i\n", i);
+			ret = -EINVAL;
+			goto err_out;
+		}
+	}
+
+	hw->spi_clk = devm_clk_get(&pdev->dev, "spi");
+	if (IS_ERR(hw->spi_clk)) {
+		dev_err(&pdev->dev, "Can't get clocks\n");
+		ret = PTR_ERR(hw->spi_clk);
+		goto err_out;
+	}
+	hw->max_speed_hz = clk_get_rate(hw->spi_clk);
+
+	init_completion(&hw->done);
+	platform_set_drvdata(pdev, master);
+
+	/* Disable extended mode due hardware problems */
+	clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCON, SYSCON3);
+
+	/* Clear possible pending interrupt */
+	clps_readl(SYNCIO);
+
+	ret = devm_request_irq(&pdev->dev, IRQ_SSEOTI, spi_clps711x_isr, 0,
+			       dev_name(&pdev->dev), hw);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't request IRQ\n");
+		clk_put(hw->spi_clk);
+		goto clk_out;
+	}
+
+	ret = spi_register_master(master);
+	if (!ret) {
+		dev_info(&pdev->dev,
+			 "SPI bus driver initialized. Master clock %u Hz\n",
+			 hw->max_speed_hz);
+		return 0;
+	}
+
+	dev_err(&pdev->dev, "Failed to register master\n");
+	devm_free_irq(&pdev->dev, IRQ_SSEOTI, hw);
+
+clk_out:
+	devm_clk_put(&pdev->dev, hw->spi_clk);
+
+err_out:
+	while (--i >= 0)
+		if (gpio_is_valid(hw->chipselect[i]))
+			gpio_free(hw->chipselect[i]);
+
+	platform_set_drvdata(pdev, NULL);
+	spi_master_put(master);
+	kfree(master);
+
+	return ret;
+}
+
+static int __devexit spi_clps711x_remove(struct platform_device *pdev)
+{
+	int i;
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
+
+	devm_free_irq(&pdev->dev, IRQ_SSEOTI, hw);
+
+	for (i = 0; i < master->num_chipselect; i++)
+		if (gpio_is_valid(hw->chipselect[i]))
+			gpio_free(hw->chipselect[i]);
+
+	devm_clk_put(&pdev->dev, hw->spi_clk);
+	platform_set_drvdata(pdev, NULL);
+	spi_unregister_master(master);
+	kfree(master);
+
+	return 0;
+}
+
+static struct platform_driver clps711x_spi_driver = {
+	.driver	= {
+		.name	= DRIVER_NAME,
+		.owner	= THIS_MODULE,
+	},
+	.probe	= spi_clps711x_probe,
+	.remove	= __devexit_p(spi_clps711x_remove),
+};
+module_platform_driver(clps711x_spi_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Alexander Shiyan <shc_work-JGs/UdohzUI@public.gmane.org>");
+MODULE_DESCRIPTION("CLPS711X SPI bus driver");
diff --git a/include/linux/platform_data/spi-clps711x.h b/include/linux/platform_data/spi-clps711x.h
new file mode 100644
index 0000000..301956e
--- /dev/null
+++ b/include/linux/platform_data/spi-clps711x.h
@@ -0,0 +1,21 @@
+/*
+ *  CLPS711X SPI bus driver definitions
+ *
+ *  Copyright (C) 2012 Alexander Shiyan <shc_work-JGs/UdohzUI@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef ____LINUX_PLATFORM_DATA_SPI_CLPS711X_H
+#define ____LINUX_PLATFORM_DATA_SPI_CLPS711X_H
+
+/* Board specific platform_data */
+struct spi_clps711x_pdata {
+	int *chipselect;	/* Array of GPIO-numbers */
+	int num_chipselect;	/* Total count of GPIOs */
+};
+
+#endif
-- 
1.7.3.4


------------------------------------------------------------------------------
Don't let slow site performance ruin your business. Deploy New Relic APM
Deploy New Relic app performance management and know exactly
what is happening inside your Ruby, Python, PHP, Java, and .NET app
Try New Relic at no cost today and get our sweet Data Nerd shirt too!
http://p.sf.net/sfu/newrelic-dev2dev