All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH 0/3] Add MPC5125 platform support
@ 2013-03-20 17:41 Matteo Facchinetti
  2013-03-20 17:41 ` [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic Matteo Facchinetti
                   ` (2 more replies)
  0 siblings, 3 replies; 17+ messages in thread
From: Matteo Facchinetti @ 2013-03-20 17:41 UTC (permalink / raw)
  To: linuxppc-dev; +Cc: gregkh, Matteo Facchinetti, agust

Add MPC5125 SoC in mpc512x family.

Inconvenient of MPC5125 SoC is to have differences in certain register
access between the others in the same family.

This patches add MPC5125 SoC unless adding configuration macro but
using general MPC512x kernel configuration.

Tested on Freescale MPC5125 tower system evaluation board.


Matteo Facchinetti (3):
  powerpc/512x: move mpc5121_generic platform to mpc512x_generic.
  serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms.
  powerpc/mpc512x: add platform code for MPC5125.

 arch/powerpc/boot/dts/mpc5125twr.dts               |  238 ++++++++++++
 arch/powerpc/configs/mpc512x_defconfig             |    2 +-
 arch/powerpc/include/asm/mpc52xx_psc.h             |   49 +++
 arch/powerpc/platforms/512x/Kconfig                |    8 +-
 arch/powerpc/platforms/512x/Makefile               |    2 +-
 arch/powerpc/platforms/512x/clock.c                |    9 +-
 arch/powerpc/platforms/512x/mpc512x.h              |    1 +
 .../512x/{mpc5121_generic.c => mpc512x_generic.c}  |    1 +
 arch/powerpc/platforms/512x/mpc512x_shared.c       |   24 +-
 drivers/tty/serial/mpc52xx_uart.c                  |  407 ++++++++++++++++++--
 10 files changed, 691 insertions(+), 50 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/mpc5125twr.dts
 rename arch/powerpc/platforms/512x/{mpc5121_generic.c => mpc512x_generic.c} (98%)

-- 
1.7.10.4

^ permalink raw reply	[flat|nested] 17+ messages in thread
* [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic.
  2013-03-20 17:41 [PATCH 0/3] Add MPC5125 platform support Matteo Facchinetti
@ 2013-03-20 17:41 ` Matteo Facchinetti
  2013-03-30 22:01   ` Anatolij Gustschin
  2013-03-20 17:41 ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Matteo Facchinetti
  2013-03-20 17:41 ` [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125 Matteo Facchinetti
  2 siblings, 1 reply; 17+ messages in thread
From: Matteo Facchinetti @ 2013-03-20 17:41 UTC (permalink / raw)
  To: linuxppc-dev; +Cc: gregkh, Matteo Facchinetti, agust

This provides a base for using 512x_generic platform on mpc5125 boards.

By this way 512x_GENERIC it could be used for all generic mpc512x boards
and kernel could be compiled with mpc512x_defconfig.

Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
---
 arch/powerpc/configs/mpc512x_defconfig                         |    2 +-
 arch/powerpc/platforms/512x/Kconfig                            |    8 ++++----
 arch/powerpc/platforms/512x/Makefile                           |    2 +-
 .../platforms/512x/{mpc5121_generic.c => mpc512x_generic.c}    |    0
 4 files changed, 6 insertions(+), 6 deletions(-)
 rename arch/powerpc/platforms/512x/{mpc5121_generic.c => mpc512x_generic.c} (100%)

diff --git a/arch/powerpc/configs/mpc512x_defconfig b/arch/powerpc/configs/mpc512x_defconfig
index 211fcc9..0d0d981 100644
--- a/arch/powerpc/configs/mpc512x_defconfig
+++ b/arch/powerpc/configs/mpc512x_defconfig
@@ -13,7 +13,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_PPC_CHRP is not set
 CONFIG_PPC_MPC512x=y
 CONFIG_MPC5121_ADS=y
-CONFIG_MPC5121_GENERIC=y
+CONFIG_MPC512x_GENERIC=y
 CONFIG_PDM360NG=y
 # CONFIG_PPC_PMAC is not set
 CONFIG_NO_HZ=y
diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig
index c169998..eb46203 100644
--- a/arch/powerpc/platforms/512x/Kconfig
+++ b/arch/powerpc/platforms/512x/Kconfig
@@ -15,16 +15,16 @@ config MPC5121_ADS
 	help
 	  This option enables support for the MPC5121E ADS board.
 
-config MPC5121_GENERIC
-	bool "Generic support for simple MPC5121 based boards"
+config MPC512x_GENERIC
+	bool "Generic support for simple MPC512x based boards"
 	depends on PPC_MPC512x
 	select DEFAULT_UIMAGE
 	help
-	  This option enables support for simple MPC5121 based boards
+	  This option enables support for simple MPC512x based boards
 	  which do not need custom platform specific setup.
 
 	  Compatible boards include:  Protonic LVT base boards (ZANMCU
-	  and VICVT2).
+	  and VICVT2), Freescale MPC5125 Tower system.
 
 config PDM360NG
 	bool "ifm PDM360NG board"
diff --git a/arch/powerpc/platforms/512x/Makefile b/arch/powerpc/platforms/512x/Makefile
index 4efc1c4..72fb934 100644
--- a/arch/powerpc/platforms/512x/Makefile
+++ b/arch/powerpc/platforms/512x/Makefile
@@ -3,5 +3,5 @@
 #
 obj-y				+= clock.o mpc512x_shared.o
 obj-$(CONFIG_MPC5121_ADS)	+= mpc5121_ads.o mpc5121_ads_cpld.o
-obj-$(CONFIG_MPC5121_GENERIC)	+= mpc5121_generic.o
+obj-$(CONFIG_MPC512x_GENERIC)	+= mpc512x_generic.o
 obj-$(CONFIG_PDM360NG)		+= pdm360ng.o
diff --git a/arch/powerpc/platforms/512x/mpc5121_generic.c b/arch/powerpc/platforms/512x/mpc512x_generic.c
similarity index 100%
rename from arch/powerpc/platforms/512x/mpc5121_generic.c
rename to arch/powerpc/platforms/512x/mpc512x_generic.c
-- 
1.7.10.4

^ permalink raw reply related	[flat|nested] 17+ messages in thread
* [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms.
  2013-03-20 17:41 [PATCH 0/3] Add MPC5125 platform support Matteo Facchinetti
  2013-03-20 17:41 ` [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic Matteo Facchinetti
@ 2013-03-20 17:41 ` Matteo Facchinetti
  2013-04-17 21:21     ` Anatolij Gustschin
  2013-04-17 21:24   ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Anatolij Gustschin
  2013-03-20 17:41 ` [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125 Matteo Facchinetti
  2 siblings, 2 replies; 17+ messages in thread
From: Matteo Facchinetti @ 2013-03-20 17:41 UTC (permalink / raw)
  To: linuxppc-dev; +Cc: gregkh, Matteo Facchinetti, agust

MPC5125 PSC controller has different registers than MPC5121.

This patch was originally created by Vladimir Ermakov
https://lists.ozlabs.org/pipermail/linuxppc-dev/2011-March/088954.html

Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>

Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
---
 arch/powerpc/include/asm/mpc52xx_psc.h |   49 ++++
 drivers/tty/serial/mpc52xx_uart.c      |  407 ++++++++++++++++++++++++++++----
 2 files changed, 414 insertions(+), 42 deletions(-)

diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h
index 2966df6..d0ece25 100644
--- a/arch/powerpc/include/asm/mpc52xx_psc.h
+++ b/arch/powerpc/include/asm/mpc52xx_psc.h
@@ -299,4 +299,53 @@ struct mpc512x_psc_fifo {
 #define rxdata_32 rxdata.rxdata_32
 };
 
+struct mpc5125_psc {
+	u8		mr1;			/* PSC + 0x00 */
+	u8		reserved0[3];
+	u8		mr2;			/* PSC + 0x04 */
+	u8		reserved1[3];
+	struct {
+		u16		status;		/* PSC + 0x08 */
+		u8		reserved2[2];
+		u8		clock_select;	/* PSC + 0x0c */
+		u8		reserved3[3];
+	} sr_csr;
+	u8		command;		/* PSC + 0x10 */
+	u8		reserved4[3];
+	union {					/* PSC + 0x14 */
+		u8		buffer_8;
+		u16		buffer_16;
+		u32		buffer_32;
+	} buffer;
+	struct {
+		u8		ipcr;		/* PSC + 0x18 */
+		u8		reserved5[3];
+		u8		acr;		/* PSC + 0x1c */
+		u8		reserved6[3];
+	} ipcr_acr;
+	struct {
+		u16		isr;		/* PSC + 0x20 */
+		u8		reserved7[2];
+		u16		imr;		/* PSC + 0x24 */
+		u8		reserved8[2];
+	} isr_imr;
+	u8		ctur;			/* PSC + 0x28 */
+	u8		reserved9[3];
+	u8		ctlr;			/* PSC + 0x2c */
+	u8		reserved10[3];
+	u32		ccr;			/* PSC + 0x30 */
+	u32		ac97slots;		/* PSC + 0x34 */
+	u32		ac97cmd;		/* PSC + 0x38 */
+	u32		ac97data;		/* PSC + 0x3c */
+	u8		reserved11[4];
+	u8		ip;			/* PSC + 0x44 */
+	u8		reserved12[3];
+	u8		op1;			/* PSC + 0x48 */
+	u8		reserved13[3];
+	u8		op0;			/* PSC + 0x4c */
+	u8		reserved14[3];
+	u32		sicr;			/* PSC + 0x50 */
+	u8		reserved15[4];	/* make eq. sizeof(mpc52xx_psc) */
+};
+
 #endif  /* __ASM_MPC52xx_PSC_H__ */
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 018bad9..3f77b9d 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -122,6 +122,15 @@ struct psc_ops {
 	void		(*fifoc_uninit)(void);
 	void		(*get_irq)(struct uart_port *, struct device_node *);
 	irqreturn_t	(*handle_irq)(struct uart_port *port);
+	u16		(*get_status)(struct uart_port *port);
+	u8		(*get_ipcr)(struct uart_port *port);
+	void		(*command)(struct uart_port *port, u8 cmd);
+	void		(*set_mode)(struct uart_port *port, u8 mr1, u8 mr2);
+	void		(*set_rts)(struct uart_port *port, int state);
+	void		(*enable_ms)(struct uart_port *port);
+	void		(*set_sicr)(struct uart_port *port, u32 val);
+	void		(*set_imr)(struct uart_port *port, u16 val);
+	u8		(*get_mr1)(struct uart_port *port);
 };
 
 /* setting the prescaler and divisor reg is common for all chips */
@@ -134,6 +143,74 @@ static inline void mpc52xx_set_divisor(struct mpc52xx_psc __iomem *psc,
 	out_8(&psc->ctlr, divisor & 0xff);
 }
 
+static inline void mpc5125_set_divisor(struct mpc5125_psc __iomem *psc,
+		u8 prescaler, unsigned int divisor)
+{
+	/* select prescaler */
+	out_8(&psc->mpc52xx_psc_clock_select, prescaler);
+	out_8(&psc->ctur, divisor >> 8);
+	out_8(&psc->ctlr, divisor & 0xff);
+}
+
+static u16 mpc52xx_psc_get_status(struct uart_port *port)
+{
+	return in_be16(&PSC(port)->mpc52xx_psc_status);
+}
+
+static u8 mpc52xx_psc_get_ipcr(struct uart_port *port)
+{
+	return in_8(&PSC(port)->mpc52xx_psc_ipcr);
+}
+
+static void mpc52xx_psc_command(struct uart_port *port, u8 cmd)
+{
+	out_8(&PSC(port)->command, cmd);
+}
+
+static void mpc52xx_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
+{
+	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
+	out_8(&PSC(port)->mode, mr1);
+	out_8(&PSC(port)->mode, mr2);
+}
+
+static void mpc52xx_psc_set_rts(struct uart_port *port, int state)
+{
+	if (state)
+		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
+	else
+		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
+}
+
+static void mpc52xx_psc_enable_ms(struct uart_port *port)
+{
+	struct mpc52xx_psc __iomem *psc = PSC(port);
+
+	/* clear D_*-bits by reading them */
+	in_8(&psc->mpc52xx_psc_ipcr);
+	/* enable CTS and DCD as IPC interrupts */
+	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
+
+	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
+	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+}
+
+static void mpc52xx_psc_set_sicr(struct uart_port *port, u32 val)
+{
+	out_be32(&PSC(port)->sicr, val);
+}
+
+static void mpc52xx_psc_set_imr(struct uart_port *port, u16 val)
+{
+	out_be16(&PSC(port)->mpc52xx_psc_imr, val);
+}
+
+static u8 mpc52xx_psc_get_mr1(struct uart_port *port)
+{
+	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
+	return in_8(&PSC(port)->mode);
+}
+
 #ifdef CONFIG_PPC_MPC52xx
 #define FIFO_52xx(port) ((struct mpc52xx_psc_fifo __iomem *)(PSC(port)+1))
 static void mpc52xx_psc_fifo_init(struct uart_port *port)
@@ -304,6 +381,15 @@ static struct psc_ops mpc52xx_psc_ops = {
 	.set_baudrate = mpc5200_psc_set_baudrate,
 	.get_irq = mpc52xx_psc_get_irq,
 	.handle_irq = mpc52xx_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
 static struct psc_ops mpc5200b_psc_ops = {
@@ -325,6 +411,15 @@ static struct psc_ops mpc5200b_psc_ops = {
 	.set_baudrate = mpc5200b_psc_set_baudrate,
 	.get_irq = mpc52xx_psc_get_irq,
 	.handle_irq = mpc52xx_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
 #endif /* CONFIG_MPC52xx */
@@ -573,6 +668,242 @@ static void mpc512x_psc_get_irq(struct uart_port *port, struct device_node *np)
 	port->irq = psc_fifoc_irq;
 }
 
+#endif
+
+#ifdef CONFIG_PPC_MPC512x
+
+#define PSC_5125(port) ((struct mpc5125_psc __iomem *)((port)->membase))
+#define FIFO_5125(port) ((struct mpc512x_psc_fifo __iomem *)(PSC_5125(port)+1))
+
+static void mpc5125_psc_fifo_init(struct uart_port *port)
+{
+	/* /32 prescaler */
+	out_8(&PSC_5125(port)->mpc52xx_psc_clock_select, 0xdd);
+
+	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
+	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
+	out_be32(&FIFO_5125(port)->txalarm, 1);
+	out_be32(&FIFO_5125(port)->tximr, 0);
+
+	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
+	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
+	out_be32(&FIFO_5125(port)->rxalarm, 1);
+	out_be32(&FIFO_5125(port)->rximr, 0);
+
+	out_be32(&FIFO_5125(port)->tximr, MPC512x_PSC_FIFO_ALARM);
+	out_be32(&FIFO_5125(port)->rximr, MPC512x_PSC_FIFO_ALARM);
+}
+
+static int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
+{
+	return !(in_be32(&FIFO_5125(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
+}
+
+static int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
+{
+	return !(in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_FULL);
+}
+
+static int mpc5125_psc_rx_rdy(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->rxsr)
+	    & in_be32(&FIFO_5125(port)->rximr)
+	    & MPC512x_PSC_FIFO_ALARM;
+}
+
+static int mpc5125_psc_tx_rdy(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->txsr)
+	    & in_be32(&FIFO_5125(port)->tximr)
+	    & MPC512x_PSC_FIFO_ALARM;
+}
+
+static int mpc5125_psc_tx_empty(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->txsr)
+	    & MPC512x_PSC_FIFO_EMPTY;
+}
+
+static void mpc5125_psc_stop_rx(struct uart_port *port)
+{
+	unsigned long rx_fifo_imr;
+
+	rx_fifo_imr = in_be32(&FIFO_5125(port)->rximr);
+	rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->rximr, rx_fifo_imr);
+}
+
+static void mpc5125_psc_start_tx(struct uart_port *port)
+{
+	unsigned long tx_fifo_imr;
+
+	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
+	tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
+}
+
+static void mpc5125_psc_stop_tx(struct uart_port *port)
+{
+	unsigned long tx_fifo_imr;
+
+	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
+	tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
+}
+
+static void mpc5125_psc_rx_clr_irq(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->rxisr, in_be32(&FIFO_5125(port)->rxisr));
+}
+
+static void mpc5125_psc_tx_clr_irq(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->txisr, in_be32(&FIFO_5125(port)->txisr));
+}
+
+static void mpc5125_psc_write_char(struct uart_port *port, unsigned char c)
+{
+	out_8(&FIFO_5125(port)->txdata_8, c);
+}
+
+static unsigned char mpc5125_psc_read_char(struct uart_port *port)
+{
+	return in_8(&FIFO_5125(port)->rxdata_8);
+}
+
+static void mpc5125_psc_cw_disable_ints(struct uart_port *port)
+{
+	port->read_status_mask =
+		in_be32(&FIFO_5125(port)->tximr) << 16 |
+		in_be32(&FIFO_5125(port)->rximr);
+	out_be32(&FIFO_5125(port)->tximr, 0);
+	out_be32(&FIFO_5125(port)->rximr, 0);
+}
+
+static void mpc5125_psc_cw_restore_ints(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->tximr,
+		(port->read_status_mask >> 16) & 0x7f);
+	out_be32(&FIFO_5125(port)->rximr, port->read_status_mask & 0x7f);
+}
+
+static unsigned int mpc5125_psc_set_baudrate(struct uart_port *port,
+					     struct ktermios *new,
+					     struct ktermios *old)
+{
+	unsigned int baud;
+	unsigned int divisor;
+
+	/*
+	 * Calculate with a /16 prescaler here.
+	 */
+
+	/* uartclk contains the ips freq */
+	baud = uart_get_baud_rate(port, new, old,
+				  port->uartclk / (16 * 0xffff) + 1,
+				  port->uartclk / 16);
+	divisor = (port->uartclk + 8 * baud) / (16 * baud);
+
+	/* enable the /16 prescaler and set the divisor */
+	mpc5125_set_divisor(PSC_5125(port), 0xdd, divisor);
+	return baud;
+}
+
+/* MPC5125 have compatible PSC FIFO Controller.
+ * Special init not needed.
+ */
+
+static u16 mpc5125_psc_get_status(struct uart_port *port)
+{
+	return in_be16(&PSC_5125(port)->mpc52xx_psc_status);
+}
+
+static u8 mpc5125_psc_get_ipcr(struct uart_port *port)
+{
+	return in_8(&PSC_5125(port)->mpc52xx_psc_ipcr);
+}
+
+static void mpc5125_psc_command(struct uart_port *port, u8 cmd)
+{
+	out_8(&PSC_5125(port)->command, cmd);
+}
+
+static void mpc5125_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
+{
+	out_8(&PSC_5125(port)->mr1, mr1);
+	out_8(&PSC_5125(port)->mr2, mr2);
+}
+
+static void mpc5125_psc_set_rts(struct uart_port *port, int state)
+{
+	if (state & TIOCM_RTS)
+		out_8(&PSC_5125(port)->op1, MPC52xx_PSC_OP_RTS);
+	else
+		out_8(&PSC_5125(port)->op0, MPC52xx_PSC_OP_RTS);
+}
+
+static void
+mpc5125_psc_enable_ms(struct uart_port *port)
+{
+	struct mpc5125_psc __iomem *psc = PSC_5125(port);
+
+	/* clear D_*-bits by reading them */
+	in_8(&psc->mpc52xx_psc_ipcr);
+	/* enable CTS and DCD as IPC interrupts */
+	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
+
+	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
+	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+}
+
+static void mpc5125_psc_set_sicr(struct uart_port *port, u32 val)
+{
+	out_be32(&PSC_5125(port)->sicr, val);
+}
+
+static void mpc5125_psc_set_imr(struct uart_port *port, u16 val)
+{
+	out_be16(&PSC_5125(port)->mpc52xx_psc_imr, val);
+}
+
+static u8 mpc5125_psc_get_mr1(struct uart_port *port)
+{
+	return in_8(&PSC_5125(port)->mr1);
+}
+
+static struct psc_ops mpc5125_psc_ops = {
+	.fifo_init = mpc5125_psc_fifo_init,
+	.raw_rx_rdy = mpc5125_psc_raw_rx_rdy,
+	.raw_tx_rdy = mpc5125_psc_raw_tx_rdy,
+	.rx_rdy = mpc5125_psc_rx_rdy,
+	.tx_rdy = mpc5125_psc_tx_rdy,
+	.tx_empty = mpc5125_psc_tx_empty,
+	.stop_rx = mpc5125_psc_stop_rx,
+	.start_tx = mpc5125_psc_start_tx,
+	.stop_tx = mpc5125_psc_stop_tx,
+	.rx_clr_irq = mpc5125_psc_rx_clr_irq,
+	.tx_clr_irq = mpc5125_psc_tx_clr_irq,
+	.write_char = mpc5125_psc_write_char,
+	.read_char = mpc5125_psc_read_char,
+	.cw_disable_ints = mpc5125_psc_cw_disable_ints,
+	.cw_restore_ints = mpc5125_psc_cw_restore_ints,
+	.set_baudrate = mpc5125_psc_set_baudrate,
+	.clock = mpc512x_psc_clock,
+	.fifoc_init = mpc512x_psc_fifoc_init,
+	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
+	.get_irq = mpc512x_psc_get_irq,
+	.handle_irq = mpc512x_psc_handle_irq,
+	.get_status = mpc5125_psc_get_status,
+	.get_ipcr = mpc5125_psc_get_ipcr,
+	.command = mpc5125_psc_command,
+	.set_mode = mpc5125_psc_set_mode,
+	.set_rts = mpc5125_psc_set_rts,
+	.enable_ms = mpc5125_psc_enable_ms,
+	.set_sicr = mpc5125_psc_set_sicr,
+	.set_imr = mpc5125_psc_set_imr,
+	.get_mr1 = mpc5125_psc_get_mr1,
+};
+
 static struct psc_ops mpc512x_psc_ops = {
 	.fifo_init = mpc512x_psc_fifo_init,
 	.raw_rx_rdy = mpc512x_psc_raw_rx_rdy,
@@ -595,8 +926,18 @@ static struct psc_ops mpc512x_psc_ops = {
 	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
 	.get_irq = mpc512x_psc_get_irq,
 	.handle_irq = mpc512x_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
-#endif
+#endif /* CONFIG_PPC_MPC512x */
+
 
 static const struct psc_ops *psc_ops;
 
@@ -613,17 +954,14 @@ mpc52xx_uart_tx_empty(struct uart_port *port)
 static void
 mpc52xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	if (mctrl & TIOCM_RTS)
-		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
-	else
-		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
+	psc_ops->set_rts(port, mctrl & TIOCM_RTS);
 }
 
 static unsigned int
 mpc52xx_uart_get_mctrl(struct uart_port *port)
 {
 	unsigned int ret = TIOCM_DSR;
-	u8 status = in_8(&PSC(port)->mpc52xx_psc_ipcr);
+	u8 status = psc_ops->get_ipcr(port);
 
 	if (!(status & MPC52xx_PSC_CTS))
 		ret |= TIOCM_CTS;
@@ -673,15 +1011,7 @@ mpc52xx_uart_stop_rx(struct uart_port *port)
 static void
 mpc52xx_uart_enable_ms(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
-
-	/* clear D_*-bits by reading them */
-	in_8(&psc->mpc52xx_psc_ipcr);
-	/* enable CTS and DCD as IPC interrupts */
-	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
-
-	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
-	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+	psc_ops->enable_ms(port);
 }
 
 static void
@@ -691,9 +1021,9 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
 	spin_lock_irqsave(&port->lock, flags);
 
 	if (ctl == -1)
-		out_8(&PSC(port)->command, MPC52xx_PSC_START_BRK);
+		psc_ops->command(port, MPC52xx_PSC_START_BRK);
 	else
-		out_8(&PSC(port)->command, MPC52xx_PSC_STOP_BRK);
+		psc_ops->command(port, MPC52xx_PSC_STOP_BRK);
 
 	spin_unlock_irqrestore(&port->lock, flags);
 }
@@ -701,7 +1031,6 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
 static int
 mpc52xx_uart_startup(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	int ret;
 
 	if (psc_ops->clock) {
@@ -717,15 +1046,15 @@ mpc52xx_uart_startup(struct uart_port *port)
 		return ret;
 
 	/* Reset/activate the port, clear and enable interrupts */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
-	out_be32(&psc->sicr, 0);	/* UART mode DCD ignored */
+	psc_ops->set_sicr(port, 0);	/* UART mode DCD ignored */
 
 	psc_ops->fifo_init(port);
 
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
-	out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
 
 	return 0;
 }
@@ -733,15 +1062,13 @@ mpc52xx_uart_startup(struct uart_port *port)
 static void
 mpc52xx_uart_shutdown(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
-
 	/* Shut down the port.  Leave TX active if on a console port */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
 	if (!uart_console(port))
-		out_8(&psc->command, MPC52xx_PSC_RST_TX);
+		psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
 	port->read_status_mask = 0;
-	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+	psc_ops->set_imr(port, port->read_status_mask);
 
 	if (psc_ops->clock)
 		psc_ops->clock(port, 0);
@@ -754,7 +1081,6 @@ static void
 mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 			 struct ktermios *old)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	unsigned long flags;
 	unsigned char mr1, mr2;
 	unsigned int j;
@@ -818,13 +1144,11 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 			"Some chars may have been lost.\n");
 
 	/* Reset the TX & RX */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
 	/* Send new mode settings */
-	out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
-	out_8(&psc->mode, mr1);
-	out_8(&psc->mode, mr2);
+	psc_ops->set_mode(port, mr1, mr2);
 	baud = psc_ops->set_baudrate(port, new, old);
 
 	/* Update the per-port timeout */
@@ -834,8 +1158,8 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 		mpc52xx_uart_enable_ms(port);
 
 	/* Reenable TX & RX */
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
-	out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
 
 	/* We're all set, release the lock */
 	spin_unlock_irqrestore(&port->lock, flags);
@@ -963,7 +1287,7 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)
 		flag = TTY_NORMAL;
 		port->icount.rx++;
 
-		status = in_be16(&PSC(port)->mpc52xx_psc_status);
+		status = psc_ops->get_status(port);
 
 		if (status & (MPC52xx_PSC_SR_PE |
 			      MPC52xx_PSC_SR_FE |
@@ -983,7 +1307,7 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)
 			}
 
 			/* Clear error condition */
-			out_8(&PSC(port)->command, MPC52xx_PSC_RST_ERR_STAT);
+			psc_ops->command(port, MPC52xx_PSC_RST_ERR_STAT);
 
 		}
 		tty_insert_flip_char(tport, ch, flag);
@@ -1066,7 +1390,7 @@ mpc5xxx_uart_process_int(struct uart_port *port)
 		if (psc_ops->tx_rdy(port))
 			keepgoing |= mpc52xx_uart_int_tx_chars(port);
 
-		status = in_8(&PSC(port)->mpc52xx_psc_ipcr);
+		status = psc_ops->get_ipcr(port);
 		if (status & MPC52xx_PSC_D_DCD)
 			uart_handle_dcd_change(port, !(status & MPC52xx_PSC_DCD));
 
@@ -1107,14 +1431,12 @@ static void __init
 mpc52xx_console_get_options(struct uart_port *port,
 			    int *baud, int *parity, int *bits, int *flow)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	unsigned char mr1;
 
 	pr_debug("mpc52xx_console_get_options(port=%p)\n", port);
 
 	/* Read the mode registers */
-	out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
-	mr1 = in_8(&psc->mode);
+	mr1 = psc_ops->get_mr1(port);
 
 	/* CT{U,L}R are write-only ! */
 	*baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
@@ -1304,6 +1626,7 @@ static struct of_device_id mpc52xx_uart_of_match[] = {
 #endif
 #ifdef CONFIG_PPC_MPC512x
 	{ .compatible = "fsl,mpc5121-psc-uart", .data = &mpc512x_psc_ops, },
+	{ .compatible = "fsl,mpc5125-psc-uart", .data = &mpc5125_psc_ops, },
 #endif
 	{},
 };
-- 
1.7.10.4

^ permalink raw reply related	[flat|nested] 17+ messages in thread
* [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125.
  2013-03-20 17:41 [PATCH 0/3] Add MPC5125 platform support Matteo Facchinetti
  2013-03-20 17:41 ` [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic Matteo Facchinetti
  2013-03-20 17:41 ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Matteo Facchinetti
@ 2013-03-20 17:41 ` Matteo Facchinetti
  2013-03-30 22:32   ` Anatolij Gustschin
  2 siblings, 1 reply; 17+ messages in thread
From: Matteo Facchinetti @ 2013-03-20 17:41 UTC (permalink / raw)
  To: linuxppc-dev; +Cc: gregkh, Matteo Facchinetti, agust

Tested on MPC5125 Tower evaluation board with
mpc512x_defconfig compile configuration.

In detail, supports for:
- PSC / UART
- RTC
- ETH
- DIU
- I2C

Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
---
 arch/powerpc/boot/dts/mpc5125twr.dts          |  238 +++++++++++++++++++++++++
 arch/powerpc/platforms/512x/clock.c           |    9 +-
 arch/powerpc/platforms/512x/mpc512x.h         |    1 +
 arch/powerpc/platforms/512x/mpc512x_generic.c |    1 +
 arch/powerpc/platforms/512x/mpc512x_shared.c  |   24 ++-
 5 files changed, 271 insertions(+), 2 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/mpc5125twr.dts

diff --git a/arch/powerpc/boot/dts/mpc5125twr.dts b/arch/powerpc/boot/dts/mpc5125twr.dts
new file mode 100644
index 0000000..afcad7a
--- /dev/null
+++ b/arch/powerpc/boot/dts/mpc5125twr.dts
@@ -0,0 +1,238 @@
+/*
+ * STx/Freescale ADS5125 MPC5125 silicon
+ *
+ * Copyright (C) 2009 Freescale Semiconductor Inc. All rights reserved.
+ *
+ * Reworked by Matteo Facchinetti (engineering@sirius-es.it)
+ * Copyright (C) 2013 Sirius Electronic Systems
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	model = "mpc5125twr"; // In BSP "mpc5125ads"
+	compatible = "fsl,mpc5125ads";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&ipic>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		ethernet0 = &eth0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,5125@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <0x20>;	// 32 bytes
+			i-cache-line-size = <0x20>;	// 32 bytes
+			d-cache-size = <0x8000>;	// L1, 32K
+			i-cache-size = <0x8000>;	// L1, 32K
+			timebase-frequency = <49500000>;// 49.5 MHz (csb/4)
+			bus-frequency = <198000000>;	// 198 MHz csb bus
+			clock-frequency = <396000000>;	// 396 MHz ppc core
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;	// 256MB at 0
+	};
+
+	sram@30000000 {
+		compatible = "fsl,mpc5121-sram";
+		reg = <0x30000000 0x08000>;		// 32K at 0x30000000
+	};
+
+	soc@80000000 {
+		compatible = "fsl,mpc5121-immr";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		#interrupt-cells = <2>;
+		ranges = <0x0 0x80000000 0x400000>;
+		reg = <0x80000000 0x400000>;
+		bus-frequency = <66000000>;	// 66 MHz ips bus
+
+		// IPIC
+		// interrupts cell = <intr #, sense>
+		// sense values match linux IORESOURCE_IRQ_* defines:
+		// sense == 8: Level, low assertion
+		// sense == 2: Edge, high-to-low change
+		//
+		ipic: interrupt-controller@c00 {
+			compatible = "fsl,mpc5121-ipic", "fsl,ipic";
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0xc00 0x100>;
+		};
+
+		rtc@a00 {	// Real time clock
+			compatible = "fsl,mpc5121-rtc";
+			reg = <0xa00 0x100>;
+			interrupts = <79 0x8 80 0x8>;
+		};
+
+		reset@e00 {	// Reset module
+			compatible = "fsl,mpc5121-reset";
+			reg = <0xe00 0x100>;
+		};
+
+		clock@f00 {	// Clock control
+			compatible = "fsl,mpc5121-clock";
+			reg = <0xf00 0x100>;
+		};
+
+		pmc@1000{  // Power Management Controller
+			compatible = "fsl,mpc5121-pmc";
+			reg = <0x1000 0x100>;
+			interrupts = <83 0x2>;
+		};
+
+		gpio0: gpio@1100 {
+			compatible = "fsl,mpc5125-gpio";
+			reg = <0x1100 0x080>;
+			interrupts = <78 0x8>;
+		};
+
+		gpio1: gpio@1180 {
+			compatible = "fsl,mpc5125-gpio";
+			reg = <0x1180 0x080>;
+			interrupts = <86 0x8>;
+		};
+
+		can@1300 { // CAN rev.2
+			compatible = "fsl,mpc5121-mscan";
+			interrupts = <12 0x8>;
+			reg = <0x1300 0x80>;
+		};
+
+		can@1380 {
+			compatible = "fsl,mpc5121-mscan";
+			interrupts = <13 0x8>;
+			reg = <0x1380 0x80>;
+		};
+
+		sdhc@1500 {
+			compatible = "fsl,mpc5121-sdhc";
+			interrupts = <8 0x8>;
+			reg = <0x1500 0x100>;
+		};
+
+		i2c@1700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x1700 0x20>;
+			interrupts = <0x9 0x8>;
+		};
+
+		i2c@1720 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x1720 0x20>;
+			interrupts = <0xa 0x8>;
+		};
+
+		i2c@1740 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x1740 0x20>;
+			interrupts = <0xb 0x8>;
+		};
+
+		i2ccontrol@1760 {
+			compatible = "fsl,mpc5121-i2c-ctrl";
+			reg = <0x1760 0x8>;
+		};
+
+		diu@2100 {
+			device_type = "display";
+			compatible = "fsl,mpc5121-diu";
+			reg = <0x2100 0x100>;
+			interrupts = <64 0x8>;
+		};
+
+		mdio@2800 {
+			compatible = "fsl,mpc5121-fec-mdio";
+			reg = <0x2800 0x800>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			phy0: ethernet-phy@0 {
+				reg = <1>;
+			};
+		};
+
+		eth0: ethernet@2800 {
+			compatible = "fsl,mpc5125-fec";
+			reg = <0x2800 0x800>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <4 0x8>;
+			phy-handle = < &phy0 >;
+			phy-connection-type = "rmii";
+		};
+
+		// IO control
+		ioctl@a000 {
+			compatible = "fsl,mpc5125-ioctl";
+			reg = <0xA000 0x1000>;
+		};
+
+		usb@3000 {
+			compatible = "fsl,mpc5121-usb2-dr";
+			reg = <0x3000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <43 0x8>;
+			dr_mode = "host";
+			phy_type = "ulpi";
+		};
+
+		// 5125 PSCs are not 52xx or 5121 PSC compatible
+		// PSC1 uart0 aka ttyPSC0
+		serial@11100 {
+			device_type = "serial";
+			compatible = "fsl,mpc5125-psc-uart", "fsl,mpc5125-psc";
+			port-number = <0>;
+			reg = <0x11100 0x100>;
+			interrupts = <40 0x8>;
+			fsl,rx-fifo-size = <16>;
+			fsl,tx-fifo-size = <16>;
+		};
+
+		// PSC9 uart1 aka ttyPSC1
+		serial@11900 {
+			device_type = "serial";
+			compatible = "fsl,mpc5125-psc-uart", "fsl,mpc5125-psc";
+			port-number = <1>;
+			reg = <0x11900 0x100>;
+			interrupts = <40 0x8>;
+			fsl,rx-fifo-size = <16>;
+			fsl,tx-fifo-size = <16>;
+		};
+
+		pscfifo@11f00 {
+			compatible = "fsl,mpc5121-psc-fifo";
+			reg = <0x11f00 0x100>;
+			interrupts = <40 0x8>;
+		};
+
+		dma@14000 {
+			compatible = "fsl,mpc5121-dma"; // BSP name: "mpc512x-dma2"
+			reg = <0x14000 0x1800>;
+			interrupts = <65 0x8>;
+		};
+	};
+};
diff --git a/arch/powerpc/platforms/512x/clock.c b/arch/powerpc/platforms/512x/clock.c
index 52d57d2..a8987dc2 100644
--- a/arch/powerpc/platforms/512x/clock.c
+++ b/arch/powerpc/platforms/512x/clock.c
@@ -29,6 +29,8 @@
 #include <asm/mpc5121.h>
 #include <asm/clk_interface.h>
 
+#include "mpc512x.h"
+
 #undef CLK_DEBUG
 
 static int clocks_initialized;
@@ -683,8 +685,13 @@ static void psc_clks_init(void)
 	struct device_node *np;
 	struct platform_device *ofdev;
 	u32 reg;
+	char *psc_compat;
+
+	psc_compat = mpc512x_select_psc_compat();
+	if (!psc_compat)
+		return;
 
-	for_each_compatible_node(np, NULL, "fsl,mpc5121-psc") {
+	for_each_compatible_node(np, NULL, psc_compat) {
 		if (!of_property_read_u32(np, "reg", &reg)) {
 			int pscnum = (reg & 0xf00) >> 8;
 			struct clk *clk = psc_dev_clk(pscnum);
diff --git a/arch/powerpc/platforms/512x/mpc512x.h b/arch/powerpc/platforms/512x/mpc512x.h
index c32b399..2b97622 100644
--- a/arch/powerpc/platforms/512x/mpc512x.h
+++ b/arch/powerpc/platforms/512x/mpc512x.h
@@ -15,6 +15,7 @@ extern void __init mpc512x_init_IRQ(void);
 extern void __init mpc512x_init(void);
 extern int __init mpc5121_clk_init(void);
 void __init mpc512x_declare_of_platform_devices(void);
+extern char *mpc512x_select_psc_compat(void);
 extern void mpc512x_restart(char *cmd);
 
 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
diff --git a/arch/powerpc/platforms/512x/mpc512x_generic.c b/arch/powerpc/platforms/512x/mpc512x_generic.c
index ca1ca66..1ca7b61 100644
--- a/arch/powerpc/platforms/512x/mpc512x_generic.c
+++ b/arch/powerpc/platforms/512x/mpc512x_generic.c
@@ -28,6 +28,7 @@
  */
 static const char * const board[] __initconst = {
 	"prt,prtlvt",
+	"fsl,mpc5125ads",
 	NULL
 };
 
diff --git a/arch/powerpc/platforms/512x/mpc512x_shared.c b/arch/powerpc/platforms/512x/mpc512x_shared.c
index d30235b..fbf67e9 100644
--- a/arch/powerpc/platforms/512x/mpc512x_shared.c
+++ b/arch/powerpc/platforms/512x/mpc512x_shared.c
@@ -350,6 +350,21 @@ void __init mpc512x_declare_of_platform_devices(void)
 
 #define DEFAULT_FIFO_SIZE 16
 
+char *mpc512x_select_psc_compat(void)
+{
+	char *psc_compats[] = {
+		"fsl,mpc5121-psc",
+		"fsl,mpc5125-psc"
+	};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(psc_compats); i++)
+		if (of_find_compatible_node(NULL, NULL, psc_compats[i]))
+			return psc_compats[i];
+
+	return NULL;
+}
+
 static unsigned int __init get_fifo_size(struct device_node *np,
 					 char *prop_name)
 {
@@ -375,9 +390,16 @@ void __init mpc512x_psc_fifo_init(void)
 	void __iomem *psc;
 	unsigned int tx_fifo_size;
 	unsigned int rx_fifo_size;
+	char *psc_compat;
 	int fifobase = 0; /* current fifo address in 32 bit words */
 
-	for_each_compatible_node(np, NULL, "fsl,mpc5121-psc") {
+	psc_compat = mpc512x_select_psc_compat();
+	if (!psc_compat) {
+		pr_err("%s: no compatible devices found\n", __func__);
+		return;
+	}
+
+	for_each_compatible_node(np, NULL, psc_compat) {
 		tx_fifo_size = get_fifo_size(np, "fsl,tx-fifo-size");
 		rx_fifo_size = get_fifo_size(np, "fsl,rx-fifo-size");
 
-- 
1.7.10.4

^ permalink raw reply related	[flat|nested] 17+ messages in thread
* Re: [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic.
  2013-03-20 17:41 ` [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic Matteo Facchinetti
@ 2013-03-30 22:01   ` Anatolij Gustschin
  0 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-03-30 22:01 UTC (permalink / raw)
  To: Matteo Facchinetti; +Cc: gregkh, linuxppc-dev

On Wed, 20 Mar 2013 18:41:52 +0100
Matteo Facchinetti <matteo.facchinetti@sirius-es.it> wrote:

> This provides a base for using 512x_generic platform on mpc5125 boards.
> 
> By this way 512x_GENERIC it could be used for all generic mpc512x boards
> and kernel could be compiled with mpc512x_defconfig.
> 
> Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> ---
>  arch/powerpc/configs/mpc512x_defconfig                         |    2 +-
>  arch/powerpc/platforms/512x/Kconfig                            |    8 ++++----
>  arch/powerpc/platforms/512x/Makefile                           |    2 +-
>  .../platforms/512x/{mpc5121_generic.c => mpc512x_generic.c}    |    0
>  4 files changed, 6 insertions(+), 6 deletions(-)
>  rename arch/powerpc/platforms/512x/{mpc5121_generic.c => mpc512x_generic.c} (100%)

with a minor change to mpc512x_generic.c, applied to next.

Thanks,

Anatolij

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125.
  2013-03-20 17:41 ` [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125 Matteo Facchinetti
@ 2013-03-30 22:32   ` Anatolij Gustschin
  2013-04-02  9:49     ` Matteo Facchinetti
  0 siblings, 1 reply; 17+ messages in thread
From: Anatolij Gustschin @ 2013-03-30 22:32 UTC (permalink / raw)
  To: Matteo Facchinetti; +Cc: gregkh, linuxppc-dev

On Wed, 20 Mar 2013 18:41:54 +0100
Matteo Facchinetti <matteo.facchinetti@sirius-es.it> wrote:
...
> diff --git a/arch/powerpc/boot/dts/mpc5125twr.dts b/arch/powerpc/boot/dts/mpc5125twr.dts
> new file mode 100644
> index 0000000..afcad7a
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/mpc5125twr.dts
...
> +
> +		diu@2100 {
> +			device_type = "display";

device_type is deprecated (for nodes other than cpu and memory).

...
> +		serial@11100 {
> +			device_type = "serial";
> +			compatible = "fsl,mpc5125-psc-uart", "fsl,mpc5125-psc";
> +			port-number = <0>;

port-number property is not used anywhere, please remove.
Remove device_type property, too.

...
> +		// PSC9 uart1 aka ttyPSC1
> +		serial@11900 {
> +			device_type = "serial";
> +			compatible = "fsl,mpc5125-psc-uart", "fsl,mpc5125-psc";
> +			port-number = <1>;

drop device_type and port-number properties.


> diff --git a/arch/powerpc/platforms/512x/clock.c b/arch/powerpc/platforms/512x/clock.c
> index 52d57d2..a8987dc2 100644
> --- a/arch/powerpc/platforms/512x/clock.c
> +++ b/arch/powerpc/platforms/512x/clock.c
> @@ -29,6 +29,8 @@
>  #include <asm/mpc5121.h>
>  #include <asm/clk_interface.h>
>  
> +#include "mpc512x.h"
> +
>  #undef CLK_DEBUG
>  
>  static int clocks_initialized;
> @@ -683,8 +685,13 @@ static void psc_clks_init(void)
>  	struct device_node *np;
>  	struct platform_device *ofdev;
>  	u32 reg;
> +	char *psc_compat;

it should be const char *.

...
> diff --git a/arch/powerpc/platforms/512x/mpc512x.h b/arch/powerpc/platforms/512x/mpc512x.h
> index c32b399..2b97622 100644
> --- a/arch/powerpc/platforms/512x/mpc512x.h
> +++ b/arch/powerpc/platforms/512x/mpc512x.h
> @@ -15,6 +15,7 @@ extern void __init mpc512x_init_IRQ(void);
>  extern void __init mpc512x_init(void);
>  extern int __init mpc5121_clk_init(void);
>  void __init mpc512x_declare_of_platform_devices(void);
> +extern char *mpc512x_select_psc_compat(void);

const char *.

...
> diff --git a/arch/powerpc/platforms/512x/mpc512x_shared.c b/arch/powerpc/platforms/512x/mpc512x_shared.c
> index d30235b..fbf67e9 100644
> --- a/arch/powerpc/platforms/512x/mpc512x_shared.c
> +++ b/arch/powerpc/platforms/512x/mpc512x_shared.c
> @@ -350,6 +350,21 @@ void __init mpc512x_declare_of_platform_devices(void)
>  
>  #define DEFAULT_FIFO_SIZE 16
>  
> +char *mpc512x_select_psc_compat(void)

const char *.

> +{
> +	char *psc_compats[] = {
> +		"fsl,mpc5121-psc",
> +		"fsl,mpc5125-psc"
> +	};
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(psc_compats); i++)
> +		if (of_find_compatible_node(NULL, NULL, psc_compats[i]))
> +			return psc_compats[i];

I don't like this, better would be to use something like:

        if (of_machine_is_compatible("fsl,mpc5121"))
                return "fsl,mpc5121-psc";

        if (of_machine_is_compatible("fsl,mpc5125"))
                return "fsl,mpc5125-psc";

but note that it will only work if we add these compatibles
to the compatible list of the root nodes in 5121 and 5125
device trees.

Thanks,

Anatolij

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125.
  2013-03-30 22:32   ` Anatolij Gustschin
@ 2013-04-02  9:49     ` Matteo Facchinetti
  2013-04-02 10:38       ` Anatolij Gustschin
  0 siblings, 1 reply; 17+ messages in thread
From: Matteo Facchinetti @ 2013-04-02  9:49 UTC (permalink / raw)
  To: Anatolij Gustschin; +Cc: gregkh, linuxppc-dev

On 03/30/2013 11:32 PM, Anatolij Gustschin wrote:
>> +{
>> +	char *psc_compats[] = {
>> +		"fsl,mpc5121-psc",
>> +		"fsl,mpc5125-psc"
>> +	};
>> +	int i;
>> +
>> +	for (i = 0; i < ARRAY_SIZE(psc_compats); i++)
>> +		if (of_find_compatible_node(NULL, NULL, psc_compats[i]))
>> +			return psc_compats[i];
> I don't like this, better would be to use something like:
>
>          if (of_machine_is_compatible("fsl,mpc5121"))
>                  return "fsl,mpc5121-psc";
>
>          if (of_machine_is_compatible("fsl,mpc5125"))
>                  return "fsl,mpc5125-psc";
>
> but note that it will only work if we add these compatibles
> to the compatible list of the root nodes in 5121 and 5125
> device trees.

I agree with you.

But I don't like that:
"fsl,mpc5121" is already present in <mpc5121.dtsi> and after its 
inclusion in <mpc5121ads.dts> , compatible root node value is replaced 
by "fsl,mpc5121ads".

Idea is automatically generate
     compatible = "fsl,mpc5121", "fsl,mpc5121ads";
using dtsi hierarchy.

Is there a way to extend compatible values instead of replace it?

Matteo

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125.
  2013-04-02  9:49     ` Matteo Facchinetti
@ 2013-04-02 10:38       ` Anatolij Gustschin
  0 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-04-02 10:38 UTC (permalink / raw)
  To: Matteo Facchinetti; +Cc: gregkh, linuxppc-dev

On Tue, 02 Apr 2013 11:49:22 +0200
Matteo Facchinetti <matteo.facchinetti@sirius-es.it> wrote:
...
> >          if (of_machine_is_compatible("fsl,mpc5121"))
> >                  return "fsl,mpc5121-psc";
> >
> >          if (of_machine_is_compatible("fsl,mpc5125"))
> >                  return "fsl,mpc5125-psc";
> >
> > but note that it will only work if we add these compatibles
> > to the compatible list of the root nodes in 5121 and 5125
> > device trees.
> 
> I agree with you.
> 
> But I don't like that:
> "fsl,mpc5121" is already present in <mpc5121.dtsi> and after its 
> inclusion in <mpc5121ads.dts> , compatible root node value is replaced 
> by "fsl,mpc5121ads".
> 
> Idea is automatically generate
>      compatible = "fsl,mpc5121", "fsl,mpc5121ads";
> using dtsi hierarchy.
> 
> Is there a way to extend compatible values instead of replace it?

Not that I am aware of. Note that the compatible list should
specify the compatibility from most specific to most general, so
the list in mpc5121ads.dts would look like

    compatible = "fsl,mpc5121ads", "fsl,mpc5121";

We can patch in-tree mpc512x dts files accordingly.

Thanks,

Anatolij

--
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0  Fax: +49-8142-66989-80 Email: office@denx.de

^ permalink raw reply	[flat|nested] 17+ messages in thread
* [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support
  2013-03-20 17:41 ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Matteo Facchinetti
@ 2013-04-17 21:21     ` Anatolij Gustschin
  2013-04-17 21:24   ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Anatolij Gustschin
  1 sibling, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-04-17 21:21 UTC (permalink / raw)
  To: linux-serial, Greg Kroah-Hartman
  Cc: linuxppc-dev, Matteo Facchinetti, Vladimir Ermakov, Anatolij Gustschin

From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>

MPC5125 PSC controller has different register layout than MPC5121.
To support MPC5125 PSC in this driver we have to provide further
psc_ops functions for SoC specific register accesses.

Add new register access functions to the psc_ops structure and
provide MPC52xx and MPC512x specific implementation for them.
Then replace remaining direct register accesses in the driver by
appropriate psc_ops function calls. The subsequent patch can now
add MPC5125 specific set of psc_ops functions.

Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
---

Greg, with your Acked-by I can push these patches to my mpc5xxx tree.
But it is fine with me if you prefer to apply them to tty tree.

Thanks,

Anatolij

Changes in v2:
 - split into two patches to simplify review
 - minor coding style changes
 - revise commit log

 drivers/tty/serial/mpc52xx_uart.c |  161 +++++++++++++++++++++++++++----------
 1 file changed, 119 insertions(+), 42 deletions(-)

diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 018bad9..5aa87ac 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -122,6 +122,15 @@ struct psc_ops {
 	void		(*fifoc_uninit)(void);
 	void		(*get_irq)(struct uart_port *, struct device_node *);
 	irqreturn_t	(*handle_irq)(struct uart_port *port);
+	u16		(*get_status)(struct uart_port *port);
+	u8		(*get_ipcr)(struct uart_port *port);
+	void		(*command)(struct uart_port *port, u8 cmd);
+	void		(*set_mode)(struct uart_port *port, u8 mr1, u8 mr2);
+	void		(*set_rts)(struct uart_port *port, int state);
+	void		(*enable_ms)(struct uart_port *port);
+	void		(*set_sicr)(struct uart_port *port, u32 val);
+	void		(*set_imr)(struct uart_port *port, u16 val);
+	u8		(*get_mr1)(struct uart_port *port);
 };
 
 /* setting the prescaler and divisor reg is common for all chips */
@@ -134,6 +143,65 @@ static inline void mpc52xx_set_divisor(struct mpc52xx_psc __iomem *psc,
 	out_8(&psc->ctlr, divisor & 0xff);
 }
 
+static u16 mpc52xx_psc_get_status(struct uart_port *port)
+{
+	return in_be16(&PSC(port)->mpc52xx_psc_status);
+}
+
+static u8 mpc52xx_psc_get_ipcr(struct uart_port *port)
+{
+	return in_8(&PSC(port)->mpc52xx_psc_ipcr);
+}
+
+static void mpc52xx_psc_command(struct uart_port *port, u8 cmd)
+{
+	out_8(&PSC(port)->command, cmd);
+}
+
+static void mpc52xx_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
+{
+	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
+	out_8(&PSC(port)->mode, mr1);
+	out_8(&PSC(port)->mode, mr2);
+}
+
+static void mpc52xx_psc_set_rts(struct uart_port *port, int state)
+{
+	if (state)
+		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
+	else
+		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
+}
+
+static void mpc52xx_psc_enable_ms(struct uart_port *port)
+{
+	struct mpc52xx_psc __iomem *psc = PSC(port);
+
+	/* clear D_*-bits by reading them */
+	in_8(&psc->mpc52xx_psc_ipcr);
+	/* enable CTS and DCD as IPC interrupts */
+	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
+
+	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
+	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+}
+
+static void mpc52xx_psc_set_sicr(struct uart_port *port, u32 val)
+{
+	out_be32(&PSC(port)->sicr, val);
+}
+
+static void mpc52xx_psc_set_imr(struct uart_port *port, u16 val)
+{
+	out_be16(&PSC(port)->mpc52xx_psc_imr, val);
+}
+
+static u8 mpc52xx_psc_get_mr1(struct uart_port *port)
+{
+	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
+	return in_8(&PSC(port)->mode);
+}
+
 #ifdef CONFIG_PPC_MPC52xx
 #define FIFO_52xx(port) ((struct mpc52xx_psc_fifo __iomem *)(PSC(port)+1))
 static void mpc52xx_psc_fifo_init(struct uart_port *port)
@@ -304,6 +372,15 @@ static struct psc_ops mpc52xx_psc_ops = {
 	.set_baudrate = mpc5200_psc_set_baudrate,
 	.get_irq = mpc52xx_psc_get_irq,
 	.handle_irq = mpc52xx_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
 static struct psc_ops mpc5200b_psc_ops = {
@@ -325,6 +402,15 @@ static struct psc_ops mpc5200b_psc_ops = {
 	.set_baudrate = mpc5200b_psc_set_baudrate,
 	.get_irq = mpc52xx_psc_get_irq,
 	.handle_irq = mpc52xx_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
 #endif /* CONFIG_MPC52xx */
@@ -595,8 +681,18 @@ static struct psc_ops mpc512x_psc_ops = {
 	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
 	.get_irq = mpc512x_psc_get_irq,
 	.handle_irq = mpc512x_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
-#endif
+#endif /* CONFIG_PPC_MPC512x */
+
 
 static const struct psc_ops *psc_ops;
 
@@ -613,17 +709,14 @@ mpc52xx_uart_tx_empty(struct uart_port *port)
 static void
 mpc52xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	if (mctrl & TIOCM_RTS)
-		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
-	else
-		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
+	psc_ops->set_rts(port, mctrl & TIOCM_RTS);
 }
 
 static unsigned int
 mpc52xx_uart_get_mctrl(struct uart_port *port)
 {
 	unsigned int ret = TIOCM_DSR;
-	u8 status = in_8(&PSC(port)->mpc52xx_psc_ipcr);
+	u8 status = psc_ops->get_ipcr(port);
 
 	if (!(status & MPC52xx_PSC_CTS))
 		ret |= TIOCM_CTS;
@@ -673,15 +766,7 @@ mpc52xx_uart_stop_rx(struct uart_port *port)
 static void
 mpc52xx_uart_enable_ms(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
-
-	/* clear D_*-bits by reading them */
-	in_8(&psc->mpc52xx_psc_ipcr);
-	/* enable CTS and DCD as IPC interrupts */
-	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
-
-	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
-	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+	psc_ops->enable_ms(port);
 }
 
 static void
@@ -691,9 +776,9 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
 	spin_lock_irqsave(&port->lock, flags);
 
 	if (ctl == -1)
-		out_8(&PSC(port)->command, MPC52xx_PSC_START_BRK);
+		psc_ops->command(port, MPC52xx_PSC_START_BRK);
 	else
-		out_8(&PSC(port)->command, MPC52xx_PSC_STOP_BRK);
+		psc_ops->command(port, MPC52xx_PSC_STOP_BRK);
 
 	spin_unlock_irqrestore(&port->lock, flags);
 }
@@ -701,7 +786,6 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
 static int
 mpc52xx_uart_startup(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	int ret;
 
 	if (psc_ops->clock) {
@@ -717,15 +801,15 @@ mpc52xx_uart_startup(struct uart_port *port)
 		return ret;
 
 	/* Reset/activate the port, clear and enable interrupts */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
-	out_be32(&psc->sicr, 0);	/* UART mode DCD ignored */
+	psc_ops->set_sicr(port, 0);	/* UART mode DCD ignored */
 
 	psc_ops->fifo_init(port);
 
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
-	out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
 
 	return 0;
 }
@@ -733,15 +817,13 @@ mpc52xx_uart_startup(struct uart_port *port)
 static void
 mpc52xx_uart_shutdown(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
-
 	/* Shut down the port.  Leave TX active if on a console port */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
 	if (!uart_console(port))
-		out_8(&psc->command, MPC52xx_PSC_RST_TX);
+		psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
 	port->read_status_mask = 0;
-	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+	psc_ops->set_imr(port, port->read_status_mask);
 
 	if (psc_ops->clock)
 		psc_ops->clock(port, 0);
@@ -754,7 +836,6 @@ static void
 mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 			 struct ktermios *old)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	unsigned long flags;
 	unsigned char mr1, mr2;
 	unsigned int j;
@@ -818,13 +899,11 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 			"Some chars may have been lost.\n");
 
 	/* Reset the TX & RX */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
 	/* Send new mode settings */
-	out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
-	out_8(&psc->mode, mr1);
-	out_8(&psc->mode, mr2);
+	psc_ops->set_mode(port, mr1, mr2);
 	baud = psc_ops->set_baudrate(port, new, old);
 
 	/* Update the per-port timeout */
@@ -834,8 +913,8 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 		mpc52xx_uart_enable_ms(port);
 
 	/* Reenable TX & RX */
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
-	out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
 
 	/* We're all set, release the lock */
 	spin_unlock_irqrestore(&port->lock, flags);
@@ -963,7 +1042,7 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)
 		flag = TTY_NORMAL;
 		port->icount.rx++;
 
-		status = in_be16(&PSC(port)->mpc52xx_psc_status);
+		status = psc_ops->get_status(port);
 
 		if (status & (MPC52xx_PSC_SR_PE |
 			      MPC52xx_PSC_SR_FE |
@@ -983,7 +1062,7 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)
 			}
 
 			/* Clear error condition */
-			out_8(&PSC(port)->command, MPC52xx_PSC_RST_ERR_STAT);
+			psc_ops->command(port, MPC52xx_PSC_RST_ERR_STAT);
 
 		}
 		tty_insert_flip_char(tport, ch, flag);
@@ -1066,7 +1145,7 @@ mpc5xxx_uart_process_int(struct uart_port *port)
 		if (psc_ops->tx_rdy(port))
 			keepgoing |= mpc52xx_uart_int_tx_chars(port);
 
-		status = in_8(&PSC(port)->mpc52xx_psc_ipcr);
+		status = psc_ops->get_ipcr(port);
 		if (status & MPC52xx_PSC_D_DCD)
 			uart_handle_dcd_change(port, !(status & MPC52xx_PSC_DCD));
 
@@ -1107,14 +1186,12 @@ static void __init
 mpc52xx_console_get_options(struct uart_port *port,
 			    int *baud, int *parity, int *bits, int *flow)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	unsigned char mr1;
 
 	pr_debug("mpc52xx_console_get_options(port=%p)\n", port);
 
 	/* Read the mode registers */
-	out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
-	mr1 = in_8(&psc->mode);
+	mr1 = psc_ops->get_mr1(port);
 
 	/* CT{U,L}R are write-only ! */
 	*baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
-- 
1.7.9.5


^ permalink raw reply related	[flat|nested] 17+ messages in thread
* [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support
@ 2013-04-17 21:21     ` Anatolij Gustschin
  0 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-04-17 21:21 UTC (permalink / raw)
  To: linux-serial, Greg Kroah-Hartman
  Cc: Matteo Facchinetti, Anatolij Gustschin, linuxppc-dev, Vladimir Ermakov

From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>

MPC5125 PSC controller has different register layout than MPC5121.
To support MPC5125 PSC in this driver we have to provide further
psc_ops functions for SoC specific register accesses.

Add new register access functions to the psc_ops structure and
provide MPC52xx and MPC512x specific implementation for them.
Then replace remaining direct register accesses in the driver by
appropriate psc_ops function calls. The subsequent patch can now
add MPC5125 specific set of psc_ops functions.

Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
---

Greg, with your Acked-by I can push these patches to my mpc5xxx tree.
But it is fine with me if you prefer to apply them to tty tree.

Thanks,

Anatolij

Changes in v2:
 - split into two patches to simplify review
 - minor coding style changes
 - revise commit log

 drivers/tty/serial/mpc52xx_uart.c |  161 +++++++++++++++++++++++++++----------
 1 file changed, 119 insertions(+), 42 deletions(-)

diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 018bad9..5aa87ac 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -122,6 +122,15 @@ struct psc_ops {
 	void		(*fifoc_uninit)(void);
 	void		(*get_irq)(struct uart_port *, struct device_node *);
 	irqreturn_t	(*handle_irq)(struct uart_port *port);
+	u16		(*get_status)(struct uart_port *port);
+	u8		(*get_ipcr)(struct uart_port *port);
+	void		(*command)(struct uart_port *port, u8 cmd);
+	void		(*set_mode)(struct uart_port *port, u8 mr1, u8 mr2);
+	void		(*set_rts)(struct uart_port *port, int state);
+	void		(*enable_ms)(struct uart_port *port);
+	void		(*set_sicr)(struct uart_port *port, u32 val);
+	void		(*set_imr)(struct uart_port *port, u16 val);
+	u8		(*get_mr1)(struct uart_port *port);
 };
 
 /* setting the prescaler and divisor reg is common for all chips */
@@ -134,6 +143,65 @@ static inline void mpc52xx_set_divisor(struct mpc52xx_psc __iomem *psc,
 	out_8(&psc->ctlr, divisor & 0xff);
 }
 
+static u16 mpc52xx_psc_get_status(struct uart_port *port)
+{
+	return in_be16(&PSC(port)->mpc52xx_psc_status);
+}
+
+static u8 mpc52xx_psc_get_ipcr(struct uart_port *port)
+{
+	return in_8(&PSC(port)->mpc52xx_psc_ipcr);
+}
+
+static void mpc52xx_psc_command(struct uart_port *port, u8 cmd)
+{
+	out_8(&PSC(port)->command, cmd);
+}
+
+static void mpc52xx_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
+{
+	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
+	out_8(&PSC(port)->mode, mr1);
+	out_8(&PSC(port)->mode, mr2);
+}
+
+static void mpc52xx_psc_set_rts(struct uart_port *port, int state)
+{
+	if (state)
+		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
+	else
+		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
+}
+
+static void mpc52xx_psc_enable_ms(struct uart_port *port)
+{
+	struct mpc52xx_psc __iomem *psc = PSC(port);
+
+	/* clear D_*-bits by reading them */
+	in_8(&psc->mpc52xx_psc_ipcr);
+	/* enable CTS and DCD as IPC interrupts */
+	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
+
+	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
+	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+}
+
+static void mpc52xx_psc_set_sicr(struct uart_port *port, u32 val)
+{
+	out_be32(&PSC(port)->sicr, val);
+}
+
+static void mpc52xx_psc_set_imr(struct uart_port *port, u16 val)
+{
+	out_be16(&PSC(port)->mpc52xx_psc_imr, val);
+}
+
+static u8 mpc52xx_psc_get_mr1(struct uart_port *port)
+{
+	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
+	return in_8(&PSC(port)->mode);
+}
+
 #ifdef CONFIG_PPC_MPC52xx
 #define FIFO_52xx(port) ((struct mpc52xx_psc_fifo __iomem *)(PSC(port)+1))
 static void mpc52xx_psc_fifo_init(struct uart_port *port)
@@ -304,6 +372,15 @@ static struct psc_ops mpc52xx_psc_ops = {
 	.set_baudrate = mpc5200_psc_set_baudrate,
 	.get_irq = mpc52xx_psc_get_irq,
 	.handle_irq = mpc52xx_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
 static struct psc_ops mpc5200b_psc_ops = {
@@ -325,6 +402,15 @@ static struct psc_ops mpc5200b_psc_ops = {
 	.set_baudrate = mpc5200b_psc_set_baudrate,
 	.get_irq = mpc52xx_psc_get_irq,
 	.handle_irq = mpc52xx_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
 
 #endif /* CONFIG_MPC52xx */
@@ -595,8 +681,18 @@ static struct psc_ops mpc512x_psc_ops = {
 	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
 	.get_irq = mpc512x_psc_get_irq,
 	.handle_irq = mpc512x_psc_handle_irq,
+	.get_status = mpc52xx_psc_get_status,
+	.get_ipcr = mpc52xx_psc_get_ipcr,
+	.command = mpc52xx_psc_command,
+	.set_mode = mpc52xx_psc_set_mode,
+	.set_rts = mpc52xx_psc_set_rts,
+	.enable_ms = mpc52xx_psc_enable_ms,
+	.set_sicr = mpc52xx_psc_set_sicr,
+	.set_imr = mpc52xx_psc_set_imr,
+	.get_mr1 = mpc52xx_psc_get_mr1,
 };
-#endif
+#endif /* CONFIG_PPC_MPC512x */
+
 
 static const struct psc_ops *psc_ops;
 
@@ -613,17 +709,14 @@ mpc52xx_uart_tx_empty(struct uart_port *port)
 static void
 mpc52xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	if (mctrl & TIOCM_RTS)
-		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
-	else
-		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
+	psc_ops->set_rts(port, mctrl & TIOCM_RTS);
 }
 
 static unsigned int
 mpc52xx_uart_get_mctrl(struct uart_port *port)
 {
 	unsigned int ret = TIOCM_DSR;
-	u8 status = in_8(&PSC(port)->mpc52xx_psc_ipcr);
+	u8 status = psc_ops->get_ipcr(port);
 
 	if (!(status & MPC52xx_PSC_CTS))
 		ret |= TIOCM_CTS;
@@ -673,15 +766,7 @@ mpc52xx_uart_stop_rx(struct uart_port *port)
 static void
 mpc52xx_uart_enable_ms(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
-
-	/* clear D_*-bits by reading them */
-	in_8(&psc->mpc52xx_psc_ipcr);
-	/* enable CTS and DCD as IPC interrupts */
-	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
-
-	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
-	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+	psc_ops->enable_ms(port);
 }
 
 static void
@@ -691,9 +776,9 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
 	spin_lock_irqsave(&port->lock, flags);
 
 	if (ctl == -1)
-		out_8(&PSC(port)->command, MPC52xx_PSC_START_BRK);
+		psc_ops->command(port, MPC52xx_PSC_START_BRK);
 	else
-		out_8(&PSC(port)->command, MPC52xx_PSC_STOP_BRK);
+		psc_ops->command(port, MPC52xx_PSC_STOP_BRK);
 
 	spin_unlock_irqrestore(&port->lock, flags);
 }
@@ -701,7 +786,6 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
 static int
 mpc52xx_uart_startup(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	int ret;
 
 	if (psc_ops->clock) {
@@ -717,15 +801,15 @@ mpc52xx_uart_startup(struct uart_port *port)
 		return ret;
 
 	/* Reset/activate the port, clear and enable interrupts */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
-	out_be32(&psc->sicr, 0);	/* UART mode DCD ignored */
+	psc_ops->set_sicr(port, 0);	/* UART mode DCD ignored */
 
 	psc_ops->fifo_init(port);
 
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
-	out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
 
 	return 0;
 }
@@ -733,15 +817,13 @@ mpc52xx_uart_startup(struct uart_port *port)
 static void
 mpc52xx_uart_shutdown(struct uart_port *port)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
-
 	/* Shut down the port.  Leave TX active if on a console port */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
 	if (!uart_console(port))
-		out_8(&psc->command, MPC52xx_PSC_RST_TX);
+		psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
 	port->read_status_mask = 0;
-	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+	psc_ops->set_imr(port, port->read_status_mask);
 
 	if (psc_ops->clock)
 		psc_ops->clock(port, 0);
@@ -754,7 +836,6 @@ static void
 mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 			 struct ktermios *old)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	unsigned long flags;
 	unsigned char mr1, mr2;
 	unsigned int j;
@@ -818,13 +899,11 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 			"Some chars may have been lost.\n");
 
 	/* Reset the TX & RX */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
+	psc_ops->command(port, MPC52xx_PSC_RST_RX);
+	psc_ops->command(port, MPC52xx_PSC_RST_TX);
 
 	/* Send new mode settings */
-	out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
-	out_8(&psc->mode, mr1);
-	out_8(&psc->mode, mr2);
+	psc_ops->set_mode(port, mr1, mr2);
 	baud = psc_ops->set_baudrate(port, new, old);
 
 	/* Update the per-port timeout */
@@ -834,8 +913,8 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 		mpc52xx_uart_enable_ms(port);
 
 	/* Reenable TX & RX */
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
-	out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
+	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
 
 	/* We're all set, release the lock */
 	spin_unlock_irqrestore(&port->lock, flags);
@@ -963,7 +1042,7 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)
 		flag = TTY_NORMAL;
 		port->icount.rx++;
 
-		status = in_be16(&PSC(port)->mpc52xx_psc_status);
+		status = psc_ops->get_status(port);
 
 		if (status & (MPC52xx_PSC_SR_PE |
 			      MPC52xx_PSC_SR_FE |
@@ -983,7 +1062,7 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)
 			}
 
 			/* Clear error condition */
-			out_8(&PSC(port)->command, MPC52xx_PSC_RST_ERR_STAT);
+			psc_ops->command(port, MPC52xx_PSC_RST_ERR_STAT);
 
 		}
 		tty_insert_flip_char(tport, ch, flag);
@@ -1066,7 +1145,7 @@ mpc5xxx_uart_process_int(struct uart_port *port)
 		if (psc_ops->tx_rdy(port))
 			keepgoing |= mpc52xx_uart_int_tx_chars(port);
 
-		status = in_8(&PSC(port)->mpc52xx_psc_ipcr);
+		status = psc_ops->get_ipcr(port);
 		if (status & MPC52xx_PSC_D_DCD)
 			uart_handle_dcd_change(port, !(status & MPC52xx_PSC_DCD));
 
@@ -1107,14 +1186,12 @@ static void __init
 mpc52xx_console_get_options(struct uart_port *port,
 			    int *baud, int *parity, int *bits, int *flow)
 {
-	struct mpc52xx_psc __iomem *psc = PSC(port);
 	unsigned char mr1;
 
 	pr_debug("mpc52xx_console_get_options(port=%p)\n", port);
 
 	/* Read the mode registers */
-	out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
-	mr1 = in_8(&psc->mode);
+	mr1 = psc_ops->get_mr1(port);
 
 	/* CT{U,L}R are write-only ! */
 	*baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
-- 
1.7.9.5

^ permalink raw reply related	[flat|nested] 17+ messages in thread
* [PATCH v2 2/2] serial/mpc52xx_uart: add MPC5125 PSC support
  2013-04-17 21:21     ` Anatolij Gustschin
@ 2013-04-17 21:21       ` Anatolij Gustschin
  -1 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-04-17 21:21 UTC (permalink / raw)
  To: linux-serial, Greg Kroah-Hartman
  Cc: linuxppc-dev, Matteo Facchinetti, Vladimir Ermakov, Anatolij Gustschin

From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>

Add MPC5125 PSC register layout structure, MPC5125 specific
psc_ops function set and the compatible string.

Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
Changes in v2:
 - split into two patches to simplify review
 - minor coding style changes 
 - revise commit log

 arch/powerpc/include/asm/mpc52xx_psc.h |   49 +++++++
 drivers/tty/serial/mpc52xx_uart.c      |  241 ++++++++++++++++++++++++++++++++
 2 files changed, 290 insertions(+)

diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h
index 2966df6..d0ece25 100644
--- a/arch/powerpc/include/asm/mpc52xx_psc.h
+++ b/arch/powerpc/include/asm/mpc52xx_psc.h
@@ -299,4 +299,53 @@ struct mpc512x_psc_fifo {
 #define rxdata_32 rxdata.rxdata_32
 };
 
+struct mpc5125_psc {
+	u8		mr1;			/* PSC + 0x00 */
+	u8		reserved0[3];
+	u8		mr2;			/* PSC + 0x04 */
+	u8		reserved1[3];
+	struct {
+		u16		status;		/* PSC + 0x08 */
+		u8		reserved2[2];
+		u8		clock_select;	/* PSC + 0x0c */
+		u8		reserved3[3];
+	} sr_csr;
+	u8		command;		/* PSC + 0x10 */
+	u8		reserved4[3];
+	union {					/* PSC + 0x14 */
+		u8		buffer_8;
+		u16		buffer_16;
+		u32		buffer_32;
+	} buffer;
+	struct {
+		u8		ipcr;		/* PSC + 0x18 */
+		u8		reserved5[3];
+		u8		acr;		/* PSC + 0x1c */
+		u8		reserved6[3];
+	} ipcr_acr;
+	struct {
+		u16		isr;		/* PSC + 0x20 */
+		u8		reserved7[2];
+		u16		imr;		/* PSC + 0x24 */
+		u8		reserved8[2];
+	} isr_imr;
+	u8		ctur;			/* PSC + 0x28 */
+	u8		reserved9[3];
+	u8		ctlr;			/* PSC + 0x2c */
+	u8		reserved10[3];
+	u32		ccr;			/* PSC + 0x30 */
+	u32		ac97slots;		/* PSC + 0x34 */
+	u32		ac97cmd;		/* PSC + 0x38 */
+	u32		ac97data;		/* PSC + 0x3c */
+	u8		reserved11[4];
+	u8		ip;			/* PSC + 0x44 */
+	u8		reserved12[3];
+	u8		op1;			/* PSC + 0x48 */
+	u8		reserved13[3];
+	u8		op0;			/* PSC + 0x4c */
+	u8		reserved14[3];
+	u32		sicr;			/* PSC + 0x50 */
+	u8		reserved15[4];	/* make eq. sizeof(mpc52xx_psc) */
+};
+
 #endif  /* __ASM_MPC52xx_PSC_H__ */
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 5aa87ac..9c3eab5 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -658,6 +658,246 @@ static void mpc512x_psc_get_irq(struct uart_port *port, struct device_node *np)
 	port->irqflags = IRQF_SHARED;
 	port->irq = psc_fifoc_irq;
 }
+#endif
+
+#ifdef CONFIG_PPC_MPC512x
+
+#define PSC_5125(port) ((struct mpc5125_psc __iomem *)((port)->membase))
+#define FIFO_5125(port) ((struct mpc512x_psc_fifo __iomem *)(PSC_5125(port)+1))
+
+static void mpc5125_psc_fifo_init(struct uart_port *port)
+{
+	/* /32 prescaler */
+	out_8(&PSC_5125(port)->mpc52xx_psc_clock_select, 0xdd);
+
+	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
+	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
+	out_be32(&FIFO_5125(port)->txalarm, 1);
+	out_be32(&FIFO_5125(port)->tximr, 0);
+
+	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
+	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
+	out_be32(&FIFO_5125(port)->rxalarm, 1);
+	out_be32(&FIFO_5125(port)->rximr, 0);
+
+	out_be32(&FIFO_5125(port)->tximr, MPC512x_PSC_FIFO_ALARM);
+	out_be32(&FIFO_5125(port)->rximr, MPC512x_PSC_FIFO_ALARM);
+}
+
+static int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
+{
+	return !(in_be32(&FIFO_5125(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
+}
+
+static int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
+{
+	return !(in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_FULL);
+}
+
+static int mpc5125_psc_rx_rdy(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->rxsr) &
+	       in_be32(&FIFO_5125(port)->rximr) & MPC512x_PSC_FIFO_ALARM;
+}
+
+static int mpc5125_psc_tx_rdy(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->txsr) &
+	       in_be32(&FIFO_5125(port)->tximr) & MPC512x_PSC_FIFO_ALARM;
+}
+
+static int mpc5125_psc_tx_empty(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_EMPTY;
+}
+
+static void mpc5125_psc_stop_rx(struct uart_port *port)
+{
+	unsigned long rx_fifo_imr;
+
+	rx_fifo_imr = in_be32(&FIFO_5125(port)->rximr);
+	rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->rximr, rx_fifo_imr);
+}
+
+static void mpc5125_psc_start_tx(struct uart_port *port)
+{
+	unsigned long tx_fifo_imr;
+
+	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
+	tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
+}
+
+static void mpc5125_psc_stop_tx(struct uart_port *port)
+{
+	unsigned long tx_fifo_imr;
+
+	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
+	tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
+}
+
+static void mpc5125_psc_rx_clr_irq(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->rxisr, in_be32(&FIFO_5125(port)->rxisr));
+}
+
+static void mpc5125_psc_tx_clr_irq(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->txisr, in_be32(&FIFO_5125(port)->txisr));
+}
+
+static void mpc5125_psc_write_char(struct uart_port *port, unsigned char c)
+{
+	out_8(&FIFO_5125(port)->txdata_8, c);
+}
+
+static unsigned char mpc5125_psc_read_char(struct uart_port *port)
+{
+	return in_8(&FIFO_5125(port)->rxdata_8);
+}
+
+static void mpc5125_psc_cw_disable_ints(struct uart_port *port)
+{
+	port->read_status_mask =
+		in_be32(&FIFO_5125(port)->tximr) << 16 |
+		in_be32(&FIFO_5125(port)->rximr);
+	out_be32(&FIFO_5125(port)->tximr, 0);
+	out_be32(&FIFO_5125(port)->rximr, 0);
+}
+
+static void mpc5125_psc_cw_restore_ints(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->tximr,
+		(port->read_status_mask >> 16) & 0x7f);
+	out_be32(&FIFO_5125(port)->rximr, port->read_status_mask & 0x7f);
+}
+
+static inline void mpc5125_set_divisor(struct mpc5125_psc __iomem *psc,
+		u8 prescaler, unsigned int divisor)
+{
+	/* select prescaler */
+	out_8(&psc->mpc52xx_psc_clock_select, prescaler);
+	out_8(&psc->ctur, divisor >> 8);
+	out_8(&psc->ctlr, divisor & 0xff);
+}
+
+static unsigned int mpc5125_psc_set_baudrate(struct uart_port *port,
+					     struct ktermios *new,
+					     struct ktermios *old)
+{
+	unsigned int baud;
+	unsigned int divisor;
+
+	/*
+	 * Calculate with a /16 prescaler here.
+	 */
+
+	/* uartclk contains the ips freq */
+	baud = uart_get_baud_rate(port, new, old,
+				  port->uartclk / (16 * 0xffff) + 1,
+				  port->uartclk / 16);
+	divisor = (port->uartclk + 8 * baud) / (16 * baud);
+
+	/* enable the /16 prescaler and set the divisor */
+	mpc5125_set_divisor(PSC_5125(port), 0xdd, divisor);
+	return baud;
+}
+
+/*
+ * MPC5125 have compatible PSC FIFO Controller.
+ * Special init not needed.
+ */
+static u16 mpc5125_psc_get_status(struct uart_port *port)
+{
+	return in_be16(&PSC_5125(port)->mpc52xx_psc_status);
+}
+
+static u8 mpc5125_psc_get_ipcr(struct uart_port *port)
+{
+	return in_8(&PSC_5125(port)->mpc52xx_psc_ipcr);
+}
+
+static void mpc5125_psc_command(struct uart_port *port, u8 cmd)
+{
+	out_8(&PSC_5125(port)->command, cmd);
+}
+
+static void mpc5125_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
+{
+	out_8(&PSC_5125(port)->mr1, mr1);
+	out_8(&PSC_5125(port)->mr2, mr2);
+}
+
+static void mpc5125_psc_set_rts(struct uart_port *port, int state)
+{
+	if (state & TIOCM_RTS)
+		out_8(&PSC_5125(port)->op1, MPC52xx_PSC_OP_RTS);
+	else
+		out_8(&PSC_5125(port)->op0, MPC52xx_PSC_OP_RTS);
+}
+
+static void mpc5125_psc_enable_ms(struct uart_port *port)
+{
+	struct mpc5125_psc __iomem *psc = PSC_5125(port);
+
+	/* clear D_*-bits by reading them */
+	in_8(&psc->mpc52xx_psc_ipcr);
+	/* enable CTS and DCD as IPC interrupts */
+	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
+
+	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
+	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+}
+
+static void mpc5125_psc_set_sicr(struct uart_port *port, u32 val)
+{
+	out_be32(&PSC_5125(port)->sicr, val);
+}
+
+static void mpc5125_psc_set_imr(struct uart_port *port, u16 val)
+{
+	out_be16(&PSC_5125(port)->mpc52xx_psc_imr, val);
+}
+
+static u8 mpc5125_psc_get_mr1(struct uart_port *port)
+{
+	return in_8(&PSC_5125(port)->mr1);
+}
+
+static struct psc_ops mpc5125_psc_ops = {
+	.fifo_init = mpc5125_psc_fifo_init,
+	.raw_rx_rdy = mpc5125_psc_raw_rx_rdy,
+	.raw_tx_rdy = mpc5125_psc_raw_tx_rdy,
+	.rx_rdy = mpc5125_psc_rx_rdy,
+	.tx_rdy = mpc5125_psc_tx_rdy,
+	.tx_empty = mpc5125_psc_tx_empty,
+	.stop_rx = mpc5125_psc_stop_rx,
+	.start_tx = mpc5125_psc_start_tx,
+	.stop_tx = mpc5125_psc_stop_tx,
+	.rx_clr_irq = mpc5125_psc_rx_clr_irq,
+	.tx_clr_irq = mpc5125_psc_tx_clr_irq,
+	.write_char = mpc5125_psc_write_char,
+	.read_char = mpc5125_psc_read_char,
+	.cw_disable_ints = mpc5125_psc_cw_disable_ints,
+	.cw_restore_ints = mpc5125_psc_cw_restore_ints,
+	.set_baudrate = mpc5125_psc_set_baudrate,
+	.clock = mpc512x_psc_clock,
+	.fifoc_init = mpc512x_psc_fifoc_init,
+	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
+	.get_irq = mpc512x_psc_get_irq,
+	.handle_irq = mpc512x_psc_handle_irq,
+	.get_status = mpc5125_psc_get_status,
+	.get_ipcr = mpc5125_psc_get_ipcr,
+	.command = mpc5125_psc_command,
+	.set_mode = mpc5125_psc_set_mode,
+	.set_rts = mpc5125_psc_set_rts,
+	.enable_ms = mpc5125_psc_enable_ms,
+	.set_sicr = mpc5125_psc_set_sicr,
+	.set_imr = mpc5125_psc_set_imr,
+	.get_mr1 = mpc5125_psc_get_mr1,
+};
 
 static struct psc_ops mpc512x_psc_ops = {
 	.fifo_init = mpc512x_psc_fifo_init,
@@ -1381,6 +1621,7 @@ static struct of_device_id mpc52xx_uart_of_match[] = {
 #endif
 #ifdef CONFIG_PPC_MPC512x
 	{ .compatible = "fsl,mpc5121-psc-uart", .data = &mpc512x_psc_ops, },
+	{ .compatible = "fsl,mpc5125-psc-uart", .data = &mpc5125_psc_ops, },
 #endif
 	{},
 };
-- 
1.7.9.5


^ permalink raw reply related	[flat|nested] 17+ messages in thread
* [PATCH v2 2/2] serial/mpc52xx_uart: add MPC5125 PSC support
@ 2013-04-17 21:21       ` Anatolij Gustschin
  0 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-04-17 21:21 UTC (permalink / raw)
  To: linux-serial, Greg Kroah-Hartman
  Cc: Matteo Facchinetti, Anatolij Gustschin, linuxppc-dev, Vladimir Ermakov

From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>

Add MPC5125 PSC register layout structure, MPC5125 specific
psc_ops function set and the compatible string.

Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
Changes in v2:
 - split into two patches to simplify review
 - minor coding style changes 
 - revise commit log

 arch/powerpc/include/asm/mpc52xx_psc.h |   49 +++++++
 drivers/tty/serial/mpc52xx_uart.c      |  241 ++++++++++++++++++++++++++++++++
 2 files changed, 290 insertions(+)

diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h
index 2966df6..d0ece25 100644
--- a/arch/powerpc/include/asm/mpc52xx_psc.h
+++ b/arch/powerpc/include/asm/mpc52xx_psc.h
@@ -299,4 +299,53 @@ struct mpc512x_psc_fifo {
 #define rxdata_32 rxdata.rxdata_32
 };
 
+struct mpc5125_psc {
+	u8		mr1;			/* PSC + 0x00 */
+	u8		reserved0[3];
+	u8		mr2;			/* PSC + 0x04 */
+	u8		reserved1[3];
+	struct {
+		u16		status;		/* PSC + 0x08 */
+		u8		reserved2[2];
+		u8		clock_select;	/* PSC + 0x0c */
+		u8		reserved3[3];
+	} sr_csr;
+	u8		command;		/* PSC + 0x10 */
+	u8		reserved4[3];
+	union {					/* PSC + 0x14 */
+		u8		buffer_8;
+		u16		buffer_16;
+		u32		buffer_32;
+	} buffer;
+	struct {
+		u8		ipcr;		/* PSC + 0x18 */
+		u8		reserved5[3];
+		u8		acr;		/* PSC + 0x1c */
+		u8		reserved6[3];
+	} ipcr_acr;
+	struct {
+		u16		isr;		/* PSC + 0x20 */
+		u8		reserved7[2];
+		u16		imr;		/* PSC + 0x24 */
+		u8		reserved8[2];
+	} isr_imr;
+	u8		ctur;			/* PSC + 0x28 */
+	u8		reserved9[3];
+	u8		ctlr;			/* PSC + 0x2c */
+	u8		reserved10[3];
+	u32		ccr;			/* PSC + 0x30 */
+	u32		ac97slots;		/* PSC + 0x34 */
+	u32		ac97cmd;		/* PSC + 0x38 */
+	u32		ac97data;		/* PSC + 0x3c */
+	u8		reserved11[4];
+	u8		ip;			/* PSC + 0x44 */
+	u8		reserved12[3];
+	u8		op1;			/* PSC + 0x48 */
+	u8		reserved13[3];
+	u8		op0;			/* PSC + 0x4c */
+	u8		reserved14[3];
+	u32		sicr;			/* PSC + 0x50 */
+	u8		reserved15[4];	/* make eq. sizeof(mpc52xx_psc) */
+};
+
 #endif  /* __ASM_MPC52xx_PSC_H__ */
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 5aa87ac..9c3eab5 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -658,6 +658,246 @@ static void mpc512x_psc_get_irq(struct uart_port *port, struct device_node *np)
 	port->irqflags = IRQF_SHARED;
 	port->irq = psc_fifoc_irq;
 }
+#endif
+
+#ifdef CONFIG_PPC_MPC512x
+
+#define PSC_5125(port) ((struct mpc5125_psc __iomem *)((port)->membase))
+#define FIFO_5125(port) ((struct mpc512x_psc_fifo __iomem *)(PSC_5125(port)+1))
+
+static void mpc5125_psc_fifo_init(struct uart_port *port)
+{
+	/* /32 prescaler */
+	out_8(&PSC_5125(port)->mpc52xx_psc_clock_select, 0xdd);
+
+	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
+	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
+	out_be32(&FIFO_5125(port)->txalarm, 1);
+	out_be32(&FIFO_5125(port)->tximr, 0);
+
+	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
+	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
+	out_be32(&FIFO_5125(port)->rxalarm, 1);
+	out_be32(&FIFO_5125(port)->rximr, 0);
+
+	out_be32(&FIFO_5125(port)->tximr, MPC512x_PSC_FIFO_ALARM);
+	out_be32(&FIFO_5125(port)->rximr, MPC512x_PSC_FIFO_ALARM);
+}
+
+static int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
+{
+	return !(in_be32(&FIFO_5125(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
+}
+
+static int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
+{
+	return !(in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_FULL);
+}
+
+static int mpc5125_psc_rx_rdy(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->rxsr) &
+	       in_be32(&FIFO_5125(port)->rximr) & MPC512x_PSC_FIFO_ALARM;
+}
+
+static int mpc5125_psc_tx_rdy(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->txsr) &
+	       in_be32(&FIFO_5125(port)->tximr) & MPC512x_PSC_FIFO_ALARM;
+}
+
+static int mpc5125_psc_tx_empty(struct uart_port *port)
+{
+	return in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_EMPTY;
+}
+
+static void mpc5125_psc_stop_rx(struct uart_port *port)
+{
+	unsigned long rx_fifo_imr;
+
+	rx_fifo_imr = in_be32(&FIFO_5125(port)->rximr);
+	rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->rximr, rx_fifo_imr);
+}
+
+static void mpc5125_psc_start_tx(struct uart_port *port)
+{
+	unsigned long tx_fifo_imr;
+
+	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
+	tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
+}
+
+static void mpc5125_psc_stop_tx(struct uart_port *port)
+{
+	unsigned long tx_fifo_imr;
+
+	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
+	tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
+	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
+}
+
+static void mpc5125_psc_rx_clr_irq(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->rxisr, in_be32(&FIFO_5125(port)->rxisr));
+}
+
+static void mpc5125_psc_tx_clr_irq(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->txisr, in_be32(&FIFO_5125(port)->txisr));
+}
+
+static void mpc5125_psc_write_char(struct uart_port *port, unsigned char c)
+{
+	out_8(&FIFO_5125(port)->txdata_8, c);
+}
+
+static unsigned char mpc5125_psc_read_char(struct uart_port *port)
+{
+	return in_8(&FIFO_5125(port)->rxdata_8);
+}
+
+static void mpc5125_psc_cw_disable_ints(struct uart_port *port)
+{
+	port->read_status_mask =
+		in_be32(&FIFO_5125(port)->tximr) << 16 |
+		in_be32(&FIFO_5125(port)->rximr);
+	out_be32(&FIFO_5125(port)->tximr, 0);
+	out_be32(&FIFO_5125(port)->rximr, 0);
+}
+
+static void mpc5125_psc_cw_restore_ints(struct uart_port *port)
+{
+	out_be32(&FIFO_5125(port)->tximr,
+		(port->read_status_mask >> 16) & 0x7f);
+	out_be32(&FIFO_5125(port)->rximr, port->read_status_mask & 0x7f);
+}
+
+static inline void mpc5125_set_divisor(struct mpc5125_psc __iomem *psc,
+		u8 prescaler, unsigned int divisor)
+{
+	/* select prescaler */
+	out_8(&psc->mpc52xx_psc_clock_select, prescaler);
+	out_8(&psc->ctur, divisor >> 8);
+	out_8(&psc->ctlr, divisor & 0xff);
+}
+
+static unsigned int mpc5125_psc_set_baudrate(struct uart_port *port,
+					     struct ktermios *new,
+					     struct ktermios *old)
+{
+	unsigned int baud;
+	unsigned int divisor;
+
+	/*
+	 * Calculate with a /16 prescaler here.
+	 */
+
+	/* uartclk contains the ips freq */
+	baud = uart_get_baud_rate(port, new, old,
+				  port->uartclk / (16 * 0xffff) + 1,
+				  port->uartclk / 16);
+	divisor = (port->uartclk + 8 * baud) / (16 * baud);
+
+	/* enable the /16 prescaler and set the divisor */
+	mpc5125_set_divisor(PSC_5125(port), 0xdd, divisor);
+	return baud;
+}
+
+/*
+ * MPC5125 have compatible PSC FIFO Controller.
+ * Special init not needed.
+ */
+static u16 mpc5125_psc_get_status(struct uart_port *port)
+{
+	return in_be16(&PSC_5125(port)->mpc52xx_psc_status);
+}
+
+static u8 mpc5125_psc_get_ipcr(struct uart_port *port)
+{
+	return in_8(&PSC_5125(port)->mpc52xx_psc_ipcr);
+}
+
+static void mpc5125_psc_command(struct uart_port *port, u8 cmd)
+{
+	out_8(&PSC_5125(port)->command, cmd);
+}
+
+static void mpc5125_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
+{
+	out_8(&PSC_5125(port)->mr1, mr1);
+	out_8(&PSC_5125(port)->mr2, mr2);
+}
+
+static void mpc5125_psc_set_rts(struct uart_port *port, int state)
+{
+	if (state & TIOCM_RTS)
+		out_8(&PSC_5125(port)->op1, MPC52xx_PSC_OP_RTS);
+	else
+		out_8(&PSC_5125(port)->op0, MPC52xx_PSC_OP_RTS);
+}
+
+static void mpc5125_psc_enable_ms(struct uart_port *port)
+{
+	struct mpc5125_psc __iomem *psc = PSC_5125(port);
+
+	/* clear D_*-bits by reading them */
+	in_8(&psc->mpc52xx_psc_ipcr);
+	/* enable CTS and DCD as IPC interrupts */
+	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
+
+	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
+	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
+}
+
+static void mpc5125_psc_set_sicr(struct uart_port *port, u32 val)
+{
+	out_be32(&PSC_5125(port)->sicr, val);
+}
+
+static void mpc5125_psc_set_imr(struct uart_port *port, u16 val)
+{
+	out_be16(&PSC_5125(port)->mpc52xx_psc_imr, val);
+}
+
+static u8 mpc5125_psc_get_mr1(struct uart_port *port)
+{
+	return in_8(&PSC_5125(port)->mr1);
+}
+
+static struct psc_ops mpc5125_psc_ops = {
+	.fifo_init = mpc5125_psc_fifo_init,
+	.raw_rx_rdy = mpc5125_psc_raw_rx_rdy,
+	.raw_tx_rdy = mpc5125_psc_raw_tx_rdy,
+	.rx_rdy = mpc5125_psc_rx_rdy,
+	.tx_rdy = mpc5125_psc_tx_rdy,
+	.tx_empty = mpc5125_psc_tx_empty,
+	.stop_rx = mpc5125_psc_stop_rx,
+	.start_tx = mpc5125_psc_start_tx,
+	.stop_tx = mpc5125_psc_stop_tx,
+	.rx_clr_irq = mpc5125_psc_rx_clr_irq,
+	.tx_clr_irq = mpc5125_psc_tx_clr_irq,
+	.write_char = mpc5125_psc_write_char,
+	.read_char = mpc5125_psc_read_char,
+	.cw_disable_ints = mpc5125_psc_cw_disable_ints,
+	.cw_restore_ints = mpc5125_psc_cw_restore_ints,
+	.set_baudrate = mpc5125_psc_set_baudrate,
+	.clock = mpc512x_psc_clock,
+	.fifoc_init = mpc512x_psc_fifoc_init,
+	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
+	.get_irq = mpc512x_psc_get_irq,
+	.handle_irq = mpc512x_psc_handle_irq,
+	.get_status = mpc5125_psc_get_status,
+	.get_ipcr = mpc5125_psc_get_ipcr,
+	.command = mpc5125_psc_command,
+	.set_mode = mpc5125_psc_set_mode,
+	.set_rts = mpc5125_psc_set_rts,
+	.enable_ms = mpc5125_psc_enable_ms,
+	.set_sicr = mpc5125_psc_set_sicr,
+	.set_imr = mpc5125_psc_set_imr,
+	.get_mr1 = mpc5125_psc_get_mr1,
+};
 
 static struct psc_ops mpc512x_psc_ops = {
 	.fifo_init = mpc512x_psc_fifo_init,
@@ -1381,6 +1621,7 @@ static struct of_device_id mpc52xx_uart_of_match[] = {
 #endif
 #ifdef CONFIG_PPC_MPC512x
 	{ .compatible = "fsl,mpc5121-psc-uart", .data = &mpc512x_psc_ops, },
+	{ .compatible = "fsl,mpc5125-psc-uart", .data = &mpc5125_psc_ops, },
 #endif
 	{},
 };
-- 
1.7.9.5

^ permalink raw reply related	[flat|nested] 17+ messages in thread
* Re: [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms.
  2013-03-20 17:41 ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Matteo Facchinetti
  2013-04-17 21:21     ` Anatolij Gustschin
@ 2013-04-17 21:24   ` Anatolij Gustschin
  1 sibling, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-04-17 21:24 UTC (permalink / raw)
  To: Matteo Facchinetti; +Cc: gregkh, linuxppc-dev

On Wed, 20 Mar 2013 18:41:53 +0100
Matteo Facchinetti <matteo.facchinetti@sirius-es.it> wrote:

> MPC5125 PSC controller has different registers than MPC5121.
> 
> This patch was originally created by Vladimir Ermakov
> https://lists.ozlabs.org/pipermail/linuxppc-dev/2011-March/088954.html
> 
> Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
> 
> Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> ---
>  arch/powerpc/include/asm/mpc52xx_psc.h |   49 ++++
>  drivers/tty/serial/mpc52xx_uart.c      |  407 ++++++++++++++++++++++++++++----
>  2 files changed, 414 insertions(+), 42 deletions(-)

This patch should be better split to add SoC specific register accessors
first, then we can add mpc5125 changes by separate patch. I've just done
this splitting and added more descriptive commit log.

Thanks,

Anatolij

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support
  2013-04-17 21:21     ` Anatolij Gustschin
@ 2013-05-24 17:49       ` Anatolij Gustschin
  -1 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-05-24 17:49 UTC (permalink / raw)
  To: Greg Kroah-Hartman
  Cc: linux-serial, linuxppc-dev, Matteo Facchinetti, Vladimir Ermakov

On Wed, 17 Apr 2013 23:21:41 +0200
Anatolij Gustschin <agust@denx.de> wrote:

> From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> 
> MPC5125 PSC controller has different register layout than MPC5121.
> To support MPC5125 PSC in this driver we have to provide further
> psc_ops functions for SoC specific register accesses.
> 
> Add new register access functions to the psc_ops structure and
> provide MPC52xx and MPC512x specific implementation for them.
> Then replace remaining direct register accesses in the driver by
> appropriate psc_ops function calls. The subsequent patch can now
> add MPC5125 specific set of psc_ops functions.
> 
> Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
> Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> Signed-off-by: Anatolij Gustschin <agust@denx.de>
> ---
> 
> Greg, with your Acked-by I can push these patches to my mpc5xxx tree.
> But it is fine with me if you prefer to apply them to tty tree.

ping ...

Thanks,

Anatolij

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support
@ 2013-05-24 17:49       ` Anatolij Gustschin
  0 siblings, 0 replies; 17+ messages in thread
From: Anatolij Gustschin @ 2013-05-24 17:49 UTC (permalink / raw)
  To: Greg Kroah-Hartman
  Cc: Matteo Facchinetti, linuxppc-dev, Vladimir Ermakov, linux-serial

On Wed, 17 Apr 2013 23:21:41 +0200
Anatolij Gustschin <agust@denx.de> wrote:

> From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> 
> MPC5125 PSC controller has different register layout than MPC5121.
> To support MPC5125 PSC in this driver we have to provide further
> psc_ops functions for SoC specific register accesses.
> 
> Add new register access functions to the psc_ops structure and
> provide MPC52xx and MPC512x specific implementation for them.
> Then replace remaining direct register accesses in the driver by
> appropriate psc_ops function calls. The subsequent patch can now
> add MPC5125 specific set of psc_ops functions.
> 
> Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
> Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> Signed-off-by: Anatolij Gustschin <agust@denx.de>
> ---
> 
> Greg, with your Acked-by I can push these patches to my mpc5xxx tree.
> But it is fine with me if you prefer to apply them to tty tree.

ping ...

Thanks,

Anatolij

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support
  2013-05-24 17:49       ` Anatolij Gustschin
@ 2013-05-24 17:57         ` Greg Kroah-Hartman
  -1 siblings, 0 replies; 17+ messages in thread
From: Greg Kroah-Hartman @ 2013-05-24 17:57 UTC (permalink / raw)
  To: Anatolij Gustschin
  Cc: linux-serial, linuxppc-dev, Matteo Facchinetti, Vladimir Ermakov

On Fri, May 24, 2013 at 07:49:12PM +0200, Anatolij Gustschin wrote:
> On Wed, 17 Apr 2013 23:21:41 +0200
> Anatolij Gustschin <agust@denx.de> wrote:
> 
> > From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> > 
> > MPC5125 PSC controller has different register layout than MPC5121.
> > To support MPC5125 PSC in this driver we have to provide further
> > psc_ops functions for SoC specific register accesses.
> > 
> > Add new register access functions to the psc_ops structure and
> > provide MPC52xx and MPC512x specific implementation for them.
> > Then replace remaining direct register accesses in the driver by
> > appropriate psc_ops function calls. The subsequent patch can now
> > add MPC5125 specific set of psc_ops functions.
> > 
> > Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
> > Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> > Signed-off-by: Anatolij Gustschin <agust@denx.de>
> > ---
> > 
> > Greg, with your Acked-by I can push these patches to my mpc5xxx tree.
> > But it is fine with me if you prefer to apply them to tty tree.
> 
> ping ...

Sorry, I somehow lost this, so I can't see the original patch at all.
Care to resend it?

thanks,

greg k-h

^ permalink raw reply	[flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support
@ 2013-05-24 17:57         ` Greg Kroah-Hartman
  0 siblings, 0 replies; 17+ messages in thread
From: Greg Kroah-Hartman @ 2013-05-24 17:57 UTC (permalink / raw)
  To: Anatolij Gustschin
  Cc: Matteo Facchinetti, linuxppc-dev, Vladimir Ermakov, linux-serial

On Fri, May 24, 2013 at 07:49:12PM +0200, Anatolij Gustschin wrote:
> On Wed, 17 Apr 2013 23:21:41 +0200
> Anatolij Gustschin <agust@denx.de> wrote:
> 
> > From: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> > 
> > MPC5125 PSC controller has different register layout than MPC5121.
> > To support MPC5125 PSC in this driver we have to provide further
> > psc_ops functions for SoC specific register accesses.
> > 
> > Add new register access functions to the psc_ops structure and
> > provide MPC52xx and MPC512x specific implementation for them.
> > Then replace remaining direct register accesses in the driver by
> > appropriate psc_ops function calls. The subsequent patch can now
> > add MPC5125 specific set of psc_ops functions.
> > 
> > Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
> > Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
> > Signed-off-by: Anatolij Gustschin <agust@denx.de>
> > ---
> > 
> > Greg, with your Acked-by I can push these patches to my mpc5xxx tree.
> > But it is fine with me if you prefer to apply them to tty tree.
> 
> ping ...

Sorry, I somehow lost this, so I can't see the original patch at all.
Care to resend it?

thanks,

greg k-h

^ permalink raw reply	[flat|nested] 17+ messages in thread
end of thread, other threads:[~2013-05-24 17:57 UTC | newest]

Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-03-20 17:41 [PATCH 0/3] Add MPC5125 platform support Matteo Facchinetti
2013-03-20 17:41 ` [PATCH 1/3] powerpc/512x: move mpc5121_generic platform to mpc512x_generic Matteo Facchinetti
2013-03-30 22:01   ` Anatolij Gustschin
2013-03-20 17:41 ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Matteo Facchinetti
2013-04-17 21:21   ` [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support Anatolij Gustschin
2013-04-17 21:21     ` Anatolij Gustschin
2013-04-17 21:21     ` [PATCH v2 2/2] serial/mpc52xx_uart: add MPC5125 PSC support Anatolij Gustschin
2013-04-17 21:21       ` Anatolij Gustschin
2013-05-24 17:49     ` [PATCH v2 1/2] serial/mpc52xx_uart: prepare for adding MPC5125 PSC UART support Anatolij Gustschin
2013-05-24 17:49       ` Anatolij Gustschin
2013-05-24 17:57       ` Greg Kroah-Hartman
2013-05-24 17:57         ` Greg Kroah-Hartman
2013-04-17 21:24   ` [PATCH 2/3] serial/mpc52xx_uart: add PSC UART support for MPC5125 platforms Anatolij Gustschin
2013-03-20 17:41 ` [PATCH 3/3] powerpc/mpc512x: add platform code for MPC5125 Matteo Facchinetti
2013-03-30 22:32   ` Anatolij Gustschin
2013-04-02  9:49     ` Matteo Facchinetti
2013-04-02 10:38       ` Anatolij Gustschin

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.