[PATCH 1/3] ARM: ux500: Add device nodes for TCDM and TCPM memory locations

[PATCH 1/3] ARM: ux500: Add device nodes for TCDM and TCPM memory locations

[Lee Jones]

The PRCMU requires the Tightly Coupled Memory (TCM) locations in
order to function correctly. A recent move to send the base
addresses though the PRCMU platform device resource instead of
defines found in <mach/*>, means that dbx500 devices can no longer
boot successfully. These new nodes will allow the PRCMU to extract
the base memory locations from Device Tree instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 arch/arm/boot/dts/snowball.dts |    8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts
index d3ec32f..6195ffa 100644
--- a/arch/arm/boot/dts/snowball.dts
+++ b/arch/arm/boot/dts/snowball.dts
@@ -126,6 +126,14 @@
 			 };
 		};
 
+		prcmu-tcpm-per4@801b0000 {
+			reg = <0x801b0000 0x1000>;
+		};
+
+		prcmu-tcdm-per4@801b8000 {
+			reg = <0x801b8000 0x1000>;
+		};
+
 		external-bus@50000000 {
 			status = "okay";
 
-- 
1.7.10.4

[PATCH 1/3] ARM: ux500: Add device nodes for TCDM and TCPM memory locations

[Lee Jones]

The PRCMU requires the Tightly Coupled Memory (TCM) locations in
order to function correctly. A recent move to send the base
addresses though the PRCMU platform device resource instead of
defines found in <mach/*>, means that dbx500 devices can no longer
boot successfully. These new nodes will allow the PRCMU to extract
the base memory locations from Device Tree instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 arch/arm/boot/dts/snowball.dts |    8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts
index d3ec32f..6195ffa 100644
--- a/arch/arm/boot/dts/snowball.dts
+++ b/arch/arm/boot/dts/snowball.dts
@@ -126,6 +126,14 @@
 			 };
 		};
 
+		prcmu-tcpm-per4 at 801b0000 {
+			reg = <0x801b0000 0x1000>;
+		};
+
+		prcmu-tcdm-per4 at 801b8000 {
+			reg = <0x801b8000 0x1000>;
+		};
+
 		external-bus at 50000000 {
 			status = "okay";
 
-- 
1.7.10.4

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

A recent move to send the base addresses though the PRCMU platform
device resource instead of defines found in <mach/*>, means that dbx500
devices can no longer boot successfully when booting with Device Tree
enabled. This patch ensures the addresses are obtained correctly from
DT.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/db8500-prcmu.c |   28 ++++++++++++++++++++--------
 1 file changed, 20 insertions(+), 8 deletions(-)

diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 21f261b..8602bf8 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -17,6 +17,8 @@
 #include <linux/err.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/slab.h>
 #include <linux/mutex.h>
 #include <linux/completion.h>
@@ -2790,19 +2792,29 @@ static int db8500_irq_init(struct device_node *np)
 }
 
 static void dbx500_fw_version_init(struct platform_device *pdev,
-			    u32 version_offset)
+				   u32 version_offset,
+				   struct device_node *np)
 {
+	struct device_node *tcpm_np;
 	struct resource *res;
-	void __iomem *tcpm_base;
+	void __iomem *tcpm_base = NULL;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 					   "prcmu-tcpm");
 	if (!res) {
-		dev_err(&pdev->dev,
-			"Error: no prcmu tcpm memory region provided\n");
-		return;
-	}
-	tcpm_base = ioremap(res->start, resource_size(res));
+		if (np) {
+			tcpm_np = of_find_node_by_name(np->parent,
+						       "prcmu-tcpm-per4");
+			if (!tcpm_np) {
+				dev_err(&pdev->dev,
+					"no prcmu tcpm mem region provided\n");
+				return;
+			}
+			tcpm_base = of_iomap(tcpm_np, 0);
+		}
+	} else
+		tcpm_base = ioremap(res->start, resource_size(res));
+
 	if (tcpm_base != NULL) {
 		u32 version;
 
@@ -3154,7 +3166,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
 
 	init_prcm_registers();
 
-	dbx500_fw_version_init(pdev, pdata->version_offset);
+	dbx500_fw_version_init(pdev, pdata->version_offset, np);
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
 	if (!res) {
 		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
-- 
1.7.10.4

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

A recent move to send the base addresses though the PRCMU platform
device resource instead of defines found in <mach/*>, means that dbx500
devices can no longer boot successfully when booting with Device Tree
enabled. This patch ensures the addresses are obtained correctly from
DT.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/db8500-prcmu.c |   28 ++++++++++++++++++++--------
 1 file changed, 20 insertions(+), 8 deletions(-)

diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 21f261b..8602bf8 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -17,6 +17,8 @@
 #include <linux/err.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/slab.h>
 #include <linux/mutex.h>
 #include <linux/completion.h>
@@ -2790,19 +2792,29 @@ static int db8500_irq_init(struct device_node *np)
 }
 
 static void dbx500_fw_version_init(struct platform_device *pdev,
-			    u32 version_offset)
+				   u32 version_offset,
+				   struct device_node *np)
 {
+	struct device_node *tcpm_np;
 	struct resource *res;
-	void __iomem *tcpm_base;
+	void __iomem *tcpm_base = NULL;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 					   "prcmu-tcpm");
 	if (!res) {
-		dev_err(&pdev->dev,
-			"Error: no prcmu tcpm memory region provided\n");
-		return;
-	}
-	tcpm_base = ioremap(res->start, resource_size(res));
+		if (np) {
+			tcpm_np = of_find_node_by_name(np->parent,
+						       "prcmu-tcpm-per4");
+			if (!tcpm_np) {
+				dev_err(&pdev->dev,
+					"no prcmu tcpm mem region provided\n");
+				return;
+			}
+			tcpm_base = of_iomap(tcpm_np, 0);
+		}
+	} else
+		tcpm_base = ioremap(res->start, resource_size(res));
+
 	if (tcpm_base != NULL) {
 		u32 version;
 
@@ -3154,7 +3166,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
 
 	init_prcm_registers();
 
-	dbx500_fw_version_init(pdev, pdata->version_offset);
+	dbx500_fw_version_init(pdev, pdata->version_offset, np);
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
 	if (!res) {
 		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
-- 
1.7.10.4

[PATCH 3/3] mfd: db8500-prcmu: Fetch the PRCMU TCPM base address from Device Tree

[Lee Jones]

A recent move to send the base addresses though the PRCMU platform
device resource instead of defines found in <mach/*>, means that dbx500
devices can no longer boot successfully when booting with Device Tree
enabled. This patch ensures the addresses are obtained correctly from
DT instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/db8500-prcmu.c |   21 +++++++++++++++------
 1 file changed, 15 insertions(+), 6 deletions(-)

diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 8602bf8..a998edc 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -3159,8 +3159,9 @@ static void db8500_prcmu_update_cpufreq(void)
  */
 static int db8500_prcmu_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
 	struct prcmu_pdata *pdata = dev_get_platdata(&pdev->dev);
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *tcdm_np;
 	int irq = 0, err = 0, i;
 	struct resource *res;
 
@@ -3169,11 +3170,19 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
 	dbx500_fw_version_init(pdev, pdata->version_offset, np);
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
 	if (!res) {
-		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
-		return -ENOENT;
-	}
-	tcdm_base = devm_ioremap(&pdev->dev, res->start,
-			resource_size(res));
+		if (np) {
+			tcdm_np = of_find_node_by_name(np->parent,
+						       "prcmu-tcdm-per4");
+			if (!tcdm_np) {
+				dev_err(&pdev->dev,
+					"no prcmu tcdm region provided\n");
+				return -ENOENT;
+			}
+			tcdm_base = of_iomap(tcdm_np, 0);
+		}
+	} else
+		tcdm_base = devm_ioremap(&pdev->dev, res->start,
+					 resource_size(res));
 
 	/* Clean up the mailbox interrupts after pre-kernel code. */
 	writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);
-- 
1.7.10.4

[PATCH 3/3] mfd: db8500-prcmu: Fetch the PRCMU TCPM base address from Device Tree

[Lee Jones]

A recent move to send the base addresses though the PRCMU platform
device resource instead of defines found in <mach/*>, means that dbx500
devices can no longer boot successfully when booting with Device Tree
enabled. This patch ensures the addresses are obtained correctly from
DT instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/db8500-prcmu.c |   21 +++++++++++++++------
 1 file changed, 15 insertions(+), 6 deletions(-)

diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 8602bf8..a998edc 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -3159,8 +3159,9 @@ static void db8500_prcmu_update_cpufreq(void)
  */
 static int db8500_prcmu_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
 	struct prcmu_pdata *pdata = dev_get_platdata(&pdev->dev);
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *tcdm_np;
 	int irq = 0, err = 0, i;
 	struct resource *res;
 
@@ -3169,11 +3170,19 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
 	dbx500_fw_version_init(pdev, pdata->version_offset, np);
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
 	if (!res) {
-		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
-		return -ENOENT;
-	}
-	tcdm_base = devm_ioremap(&pdev->dev, res->start,
-			resource_size(res));
+		if (np) {
+			tcdm_np = of_find_node_by_name(np->parent,
+						       "prcmu-tcdm-per4");
+			if (!tcdm_np) {
+				dev_err(&pdev->dev,
+					"no prcmu tcdm region provided\n");
+				return -ENOENT;
+			}
+			tcdm_base = of_iomap(tcdm_np, 0);
+		}
+	} else
+		tcdm_base = devm_ioremap(&pdev->dev, res->start,
+					 resource_size(res));
 
 	/* Clean up the mailbox interrupts after pre-kernel code. */
 	writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);
-- 
1.7.10.4

Re: [PATCH 3/3] mfd: db8500-prcmu: Fetch the PRCMU TCPM base address from Device Tree

[Lee Jones]

Sorry Sam, looks like I missed you on this one.

> A recent move to send the base addresses though the PRCMU platform
> device resource instead of defines found in <mach/*>, means that dbx500
> devices can no longer boot successfully when booting with Device Tree
> enabled. This patch ensures the addresses are obtained correctly from
> DT instead.
> 
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
>  drivers/mfd/db8500-prcmu.c |   21 +++++++++++++++------
>  1 file changed, 15 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
> index 8602bf8..a998edc 100644
> --- a/drivers/mfd/db8500-prcmu.c
> +++ b/drivers/mfd/db8500-prcmu.c
> @@ -3159,8 +3159,9 @@ static void db8500_prcmu_update_cpufreq(void)
>   */
>  static int db8500_prcmu_probe(struct platform_device *pdev)
>  {
> -	struct device_node *np = pdev->dev.of_node;
>  	struct prcmu_pdata *pdata = dev_get_platdata(&pdev->dev);
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device_node *tcdm_np;
>  	int irq = 0, err = 0, i;
>  	struct resource *res;
>  
> @@ -3169,11 +3170,19 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
>  	dbx500_fw_version_init(pdev, pdata->version_offset, np);
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
>  	if (!res) {
> -		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
> -		return -ENOENT;
> -	}
> -	tcdm_base = devm_ioremap(&pdev->dev, res->start,
> -			resource_size(res));
> +		if (np) {
> +			tcdm_np = of_find_node_by_name(np->parent,
> +						       "prcmu-tcdm-per4");
> +			if (!tcdm_np) {
> +				dev_err(&pdev->dev,
> +					"no prcmu tcdm region provided\n");
> +				return -ENOENT;
> +			}
> +			tcdm_base = of_iomap(tcdm_np, 0);
> +		}
> +	} else
> +		tcdm_base = devm_ioremap(&pdev->dev, res->start,
> +					 resource_size(res));
>  
>  	/* Clean up the mailbox interrupts after pre-kernel code. */
>  	writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 3/3] mfd: db8500-prcmu: Fetch the PRCMU TCPM base address from Device Tree

[Lee Jones]

Sorry Sam, looks like I missed you on this one.

> A recent move to send the base addresses though the PRCMU platform
> device resource instead of defines found in <mach/*>, means that dbx500
> devices can no longer boot successfully when booting with Device Tree
> enabled. This patch ensures the addresses are obtained correctly from
> DT instead.
> 
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
>  drivers/mfd/db8500-prcmu.c |   21 +++++++++++++++------
>  1 file changed, 15 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
> index 8602bf8..a998edc 100644
> --- a/drivers/mfd/db8500-prcmu.c
> +++ b/drivers/mfd/db8500-prcmu.c
> @@ -3159,8 +3159,9 @@ static void db8500_prcmu_update_cpufreq(void)
>   */
>  static int db8500_prcmu_probe(struct platform_device *pdev)
>  {
> -	struct device_node *np = pdev->dev.of_node;
>  	struct prcmu_pdata *pdata = dev_get_platdata(&pdev->dev);
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device_node *tcdm_np;
>  	int irq = 0, err = 0, i;
>  	struct resource *res;
>  
> @@ -3169,11 +3170,19 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
>  	dbx500_fw_version_init(pdev, pdata->version_offset, np);
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
>  	if (!res) {
> -		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
> -		return -ENOENT;
> -	}
> -	tcdm_base = devm_ioremap(&pdev->dev, res->start,
> -			resource_size(res));
> +		if (np) {
> +			tcdm_np = of_find_node_by_name(np->parent,
> +						       "prcmu-tcdm-per4");
> +			if (!tcdm_np) {
> +				dev_err(&pdev->dev,
> +					"no prcmu tcdm region provided\n");
> +				return -ENOENT;
> +			}
> +			tcdm_base = of_iomap(tcdm_np, 0);
> +		}
> +	} else
> +		tcdm_base = devm_ioremap(&pdev->dev, res->start,
> +					 resource_size(res));
>  
>  	/* Clean up the mailbox interrupts after pre-kernel code. */
>  	writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

Sam, and this one, sorry.

> A recent move to send the base addresses though the PRCMU platform
> device resource instead of defines found in <mach/*>, means that dbx500
> devices can no longer boot successfully when booting with Device Tree
> enabled. This patch ensures the addresses are obtained correctly from
> DT.
> 
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
>  drivers/mfd/db8500-prcmu.c |   28 ++++++++++++++++++++--------
>  1 file changed, 20 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
> index 21f261b..8602bf8 100644
> --- a/drivers/mfd/db8500-prcmu.c
> +++ b/drivers/mfd/db8500-prcmu.c
> @@ -17,6 +17,8 @@
>  #include <linux/err.h>
>  #include <linux/spinlock.h>
>  #include <linux/io.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
>  #include <linux/slab.h>
>  #include <linux/mutex.h>
>  #include <linux/completion.h>
> @@ -2790,19 +2792,29 @@ static int db8500_irq_init(struct device_node *np)
>  }
>  
>  static void dbx500_fw_version_init(struct platform_device *pdev,
> -			    u32 version_offset)
> +				   u32 version_offset,
> +				   struct device_node *np)
>  {
> +	struct device_node *tcpm_np;
>  	struct resource *res;
> -	void __iomem *tcpm_base;
> +	void __iomem *tcpm_base = NULL;
>  
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>  					   "prcmu-tcpm");
>  	if (!res) {
> -		dev_err(&pdev->dev,
> -			"Error: no prcmu tcpm memory region provided\n");
> -		return;
> -	}
> -	tcpm_base = ioremap(res->start, resource_size(res));
> +		if (np) {
> +			tcpm_np = of_find_node_by_name(np->parent,
> +						       "prcmu-tcpm-per4");
> +			if (!tcpm_np) {
> +				dev_err(&pdev->dev,
> +					"no prcmu tcpm mem region provided\n");
> +				return;
> +			}
> +			tcpm_base = of_iomap(tcpm_np, 0);
> +		}
> +	} else
> +		tcpm_base = ioremap(res->start, resource_size(res));
> +
>  	if (tcpm_base != NULL) {
>  		u32 version;
>  
> @@ -3154,7 +3166,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
>  
>  	init_prcm_registers();
>  
> -	dbx500_fw_version_init(pdev, pdata->version_offset);
> +	dbx500_fw_version_init(pdev, pdata->version_offset, np);
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
>  	if (!res) {
>  		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

Sam, and this one, sorry.

> A recent move to send the base addresses though the PRCMU platform
> device resource instead of defines found in <mach/*>, means that dbx500
> devices can no longer boot successfully when booting with Device Tree
> enabled. This patch ensures the addresses are obtained correctly from
> DT.
> 
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
>  drivers/mfd/db8500-prcmu.c |   28 ++++++++++++++++++++--------
>  1 file changed, 20 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
> index 21f261b..8602bf8 100644
> --- a/drivers/mfd/db8500-prcmu.c
> +++ b/drivers/mfd/db8500-prcmu.c
> @@ -17,6 +17,8 @@
>  #include <linux/err.h>
>  #include <linux/spinlock.h>
>  #include <linux/io.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
>  #include <linux/slab.h>
>  #include <linux/mutex.h>
>  #include <linux/completion.h>
> @@ -2790,19 +2792,29 @@ static int db8500_irq_init(struct device_node *np)
>  }
>  
>  static void dbx500_fw_version_init(struct platform_device *pdev,
> -			    u32 version_offset)
> +				   u32 version_offset,
> +				   struct device_node *np)
>  {
> +	struct device_node *tcpm_np;
>  	struct resource *res;
> -	void __iomem *tcpm_base;
> +	void __iomem *tcpm_base = NULL;
>  
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>  					   "prcmu-tcpm");
>  	if (!res) {
> -		dev_err(&pdev->dev,
> -			"Error: no prcmu tcpm memory region provided\n");
> -		return;
> -	}
> -	tcpm_base = ioremap(res->start, resource_size(res));
> +		if (np) {
> +			tcpm_np = of_find_node_by_name(np->parent,
> +						       "prcmu-tcpm-per4");
> +			if (!tcpm_np) {
> +				dev_err(&pdev->dev,
> +					"no prcmu tcpm mem region provided\n");
> +				return;
> +			}
> +			tcpm_base = of_iomap(tcpm_np, 0);
> +		}
> +	} else
> +		tcpm_base = ioremap(res->start, resource_size(res));
> +
>  	if (tcpm_base != NULL) {
>  		u32 version;
>  
> @@ -3154,7 +3166,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
>  
>  	init_prcm_registers();
>  
> -	dbx500_fw_version_init(pdev, pdata->version_offset);
> +	dbx500_fw_version_init(pdev, pdata->version_offset, np);
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
>  	if (!res) {
>  		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Arnd Bergmann]

On Monday 25 March 2013, Lee Jones wrote:
>         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>                                            "prcmu-tcpm");
>         if (!res) {
> -               dev_err(&pdev->dev,
> -                       "Error: no prcmu tcpm memory region provided\n");
> -               return;
> -       }
> -       tcpm_base = ioremap(res->start, resource_size(res));
> +               if (np) {
> +                       tcpm_np = of_find_node_by_name(np->parent,
> +                                                      "prcmu-tcpm-per4");
> +                       if (!tcpm_np) {
> +                               dev_err(&pdev->dev,
> +                                       "no prcmu tcpm mem region provided\n");
> +                               return;
> +                       }
> +                       tcpm_base = of_iomap(tcpm_np, 0);
> +               }
> +       } else
> +               tcpm_base = ioremap(res->start, resource_size(res));
> +

Why don't you just add these extra registers to the prcmu node itself like

diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 9de9309..6ee6c31 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -191,8 +191,8 @@
 
 		prcmu: prcmu@80157000 {
 			compatible = "stericsson,db8500-prcmu";
-			reg = <0x80157000 0x1000>;
-			reg-names = "prcmu";
+			reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
+			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
 			interrupts = <0 47 0x4>;
 			#address-cells = <1>;
 			#size-cells = <1>;


and document those in the prcmu binding?

That would keep the code simpler and the same for both cases.

	Arnd

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Arnd Bergmann]

On Monday 25 March 2013, Lee Jones wrote:
>         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>                                            "prcmu-tcpm");
>         if (!res) {
> -               dev_err(&pdev->dev,
> -                       "Error: no prcmu tcpm memory region provided\n");
> -               return;
> -       }
> -       tcpm_base = ioremap(res->start, resource_size(res));
> +               if (np) {
> +                       tcpm_np = of_find_node_by_name(np->parent,
> +                                                      "prcmu-tcpm-per4");
> +                       if (!tcpm_np) {
> +                               dev_err(&pdev->dev,
> +                                       "no prcmu tcpm mem region provided\n");
> +                               return;
> +                       }
> +                       tcpm_base = of_iomap(tcpm_np, 0);
> +               }
> +       } else
> +               tcpm_base = ioremap(res->start, resource_size(res));
> +

Why don't you just add these extra registers to the prcmu node itself like

diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
index 9de9309..6ee6c31 100644
--- a/arch/arm/boot/dts/dbx5x0.dtsi
+++ b/arch/arm/boot/dts/dbx5x0.dtsi
@@ -191,8 +191,8 @@
 
 		prcmu: prcmu at 80157000 {
 			compatible = "stericsson,db8500-prcmu";
-			reg = <0x80157000 0x1000>;
-			reg-names = "prcmu";
+			reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
+			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
 			interrupts = <0 47 0x4>;
 			#address-cells = <1>;
 			#size-cells = <1>;


and document those in the prcmu binding?

That would keep the code simpler and the same for both cases.

	Arnd

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> >                                            "prcmu-tcpm");
> >         if (!res) {
> > -               dev_err(&pdev->dev,
> > -                       "Error: no prcmu tcpm memory region provided\n");
> > -               return;
> > -       }
> > -       tcpm_base = ioremap(res->start, resource_size(res));
> > +               if (np) {
> > +                       tcpm_np = of_find_node_by_name(np->parent,
> > +                                                      "prcmu-tcpm-per4");
> > +                       if (!tcpm_np) {
> > +                               dev_err(&pdev->dev,
> > +                                       "no prcmu tcpm mem region provided\n");
> > +                               return;
> > +                       }
> > +                       tcpm_base = of_iomap(tcpm_np, 0);
> > +               }
> > +       } else
> > +               tcpm_base = ioremap(res->start, resource_size(res));
> > +
> 
> Why don't you just add these extra registers to the prcmu node itself like
> 
> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
> index 9de9309..6ee6c31 100644
> --- a/arch/arm/boot/dts/dbx5x0.dtsi
> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
> @@ -191,8 +191,8 @@
>  
>  		prcmu: prcmu@80157000 {
>  			compatible = "stericsson,db8500-prcmu";
> -			reg = <0x80157000 0x1000>;
> -			reg-names = "prcmu";
> +			reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
> +			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>  			interrupts = <0 47 0x4>;
>  			#address-cells = <1>;
>  			#size-cells = <1>;
> 
> 
> and document those in the prcmu binding?
> 
> That would keep the code simpler and the same for both cases.

I'm not sure you can. These addresses differ from platform to
platform, so I'd need to provide the base PRCMU address in
dbx5x0.dtsi, then the other two in the dts files. Can you do that?

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> >                                            "prcmu-tcpm");
> >         if (!res) {
> > -               dev_err(&pdev->dev,
> > -                       "Error: no prcmu tcpm memory region provided\n");
> > -               return;
> > -       }
> > -       tcpm_base = ioremap(res->start, resource_size(res));
> > +               if (np) {
> > +                       tcpm_np = of_find_node_by_name(np->parent,
> > +                                                      "prcmu-tcpm-per4");
> > +                       if (!tcpm_np) {
> > +                               dev_err(&pdev->dev,
> > +                                       "no prcmu tcpm mem region provided\n");
> > +                               return;
> > +                       }
> > +                       tcpm_base = of_iomap(tcpm_np, 0);
> > +               }
> > +       } else
> > +               tcpm_base = ioremap(res->start, resource_size(res));
> > +
> 
> Why don't you just add these extra registers to the prcmu node itself like
> 
> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
> index 9de9309..6ee6c31 100644
> --- a/arch/arm/boot/dts/dbx5x0.dtsi
> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
> @@ -191,8 +191,8 @@
>  
>  		prcmu: prcmu at 80157000 {
>  			compatible = "stericsson,db8500-prcmu";
> -			reg = <0x80157000 0x1000>;
> -			reg-names = "prcmu";
> +			reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
> +			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>  			interrupts = <0 47 0x4>;
>  			#address-cells = <1>;
>  			#size-cells = <1>;
> 
> 
> and document those in the prcmu binding?
> 
> That would keep the code simpler and the same for both cases.

I'm not sure you can. These addresses differ from platform to
platform, so I'd need to provide the base PRCMU address in
dbx5x0.dtsi, then the other two in the dts files. Can you do that?

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Linus Walleij]

On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:

>> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>> >                                            "prcmu-tcpm");
>> >         if (!res) {
>> > -               dev_err(&pdev->dev,
>> > -                       "Error: no prcmu tcpm memory region provided\n");
>> > -               return;
>> > -       }
>> > -       tcpm_base = ioremap(res->start, resource_size(res));
>> > +               if (np) {
>> > +                       tcpm_np = of_find_node_by_name(np->parent,
>> > +                                                      "prcmu-tcpm-per4");
>> > +                       if (!tcpm_np) {
>> > +                               dev_err(&pdev->dev,
>> > +                                       "no prcmu tcpm mem region provided\n");
>> > +                               return;
>> > +                       }
>> > +                       tcpm_base = of_iomap(tcpm_np, 0);
>> > +               }
>> > +       } else
>> > +               tcpm_base = ioremap(res->start, resource_size(res));
>> > +
>>
>> Why don't you just add these extra registers to the prcmu node itself like
>>
>> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
>> index 9de9309..6ee6c31 100644
>> --- a/arch/arm/boot/dts/dbx5x0.dtsi
>> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
>> @@ -191,8 +191,8 @@
>>
>>               prcmu: prcmu@80157000 {
>>                       compatible = "stericsson,db8500-prcmu";
>> -                     reg = <0x80157000 0x1000>;
>> -                     reg-names = "prcmu";
>> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
>> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>>                       interrupts = <0 47 0x4>;
>>                       #address-cells = <1>;
>>                       #size-cells = <1>;
>>
>>
>> and document those in the prcmu binding?
>>
>> That would keep the code simpler and the same for both cases.
>
> I'm not sure you can. These addresses differ from platform to
> platform, so I'd need to provide the base PRCMU address in
> dbx5x0.dtsi, then the other two in the dts files. Can you do that?

Better ask on devicetree-discuss.

What it reflects are differences between SoC:s, so I think the
right solution is to split it in a three-layer cake:

dbx5x0.dtsi -> included by
db8500.dtsi -> included by
snowball/hrefv60plus.dts

dbx5x0.dtsi -> included by
dbx540.dtsi -> included by
ccu9540/ccu8540.dts

Here you may insert the reg property into the node at the
db8500.dtsi or dbx540.dtsi layer.

If you prefer I can cook a patch...

Yours,
Linus Walleij

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Linus Walleij]

On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:

>> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>> >                                            "prcmu-tcpm");
>> >         if (!res) {
>> > -               dev_err(&pdev->dev,
>> > -                       "Error: no prcmu tcpm memory region provided\n");
>> > -               return;
>> > -       }
>> > -       tcpm_base = ioremap(res->start, resource_size(res));
>> > +               if (np) {
>> > +                       tcpm_np = of_find_node_by_name(np->parent,
>> > +                                                      "prcmu-tcpm-per4");
>> > +                       if (!tcpm_np) {
>> > +                               dev_err(&pdev->dev,
>> > +                                       "no prcmu tcpm mem region provided\n");
>> > +                               return;
>> > +                       }
>> > +                       tcpm_base = of_iomap(tcpm_np, 0);
>> > +               }
>> > +       } else
>> > +               tcpm_base = ioremap(res->start, resource_size(res));
>> > +
>>
>> Why don't you just add these extra registers to the prcmu node itself like
>>
>> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
>> index 9de9309..6ee6c31 100644
>> --- a/arch/arm/boot/dts/dbx5x0.dtsi
>> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
>> @@ -191,8 +191,8 @@
>>
>>               prcmu: prcmu at 80157000 {
>>                       compatible = "stericsson,db8500-prcmu";
>> -                     reg = <0x80157000 0x1000>;
>> -                     reg-names = "prcmu";
>> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
>> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>>                       interrupts = <0 47 0x4>;
>>                       #address-cells = <1>;
>>                       #size-cells = <1>;
>>
>>
>> and document those in the prcmu binding?
>>
>> That would keep the code simpler and the same for both cases.
>
> I'm not sure you can. These addresses differ from platform to
> platform, so I'd need to provide the base PRCMU address in
> dbx5x0.dtsi, then the other two in the dts files. Can you do that?

Better ask on devicetree-discuss.

What it reflects are differences between SoC:s, so I think the
right solution is to split it in a three-layer cake:

dbx5x0.dtsi -> included by
db8500.dtsi -> included by
snowball/hrefv60plus.dts

dbx5x0.dtsi -> included by
dbx540.dtsi -> included by
ccu9540/ccu8540.dts

Here you may insert the reg property into the node at the
db8500.dtsi or dbx540.dtsi layer.

If you prefer I can cook a patch...

Yours,
Linus Walleij

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

On Mon, 25 Mar 2013, Linus Walleij wrote:

> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:
> 
> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> >> >                                            "prcmu-tcpm");
> >> >         if (!res) {
> >> > -               dev_err(&pdev->dev,
> >> > -                       "Error: no prcmu tcpm memory region provided\n");
> >> > -               return;
> >> > -       }
> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
> >> > +               if (np) {
> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
> >> > +                                                      "prcmu-tcpm-per4");
> >> > +                       if (!tcpm_np) {
> >> > +                               dev_err(&pdev->dev,
> >> > +                                       "no prcmu tcpm mem region provided\n");
> >> > +                               return;
> >> > +                       }
> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
> >> > +               }
> >> > +       } else
> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
> >> > +
> >>
> >> Why don't you just add these extra registers to the prcmu node itself like
> >>
> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
> >> index 9de9309..6ee6c31 100644
> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
> >> @@ -191,8 +191,8 @@
> >>
> >>               prcmu: prcmu@80157000 {
> >>                       compatible = "stericsson,db8500-prcmu";
> >> -                     reg = <0x80157000 0x1000>;
> >> -                     reg-names = "prcmu";
> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
> >>                       interrupts = <0 47 0x4>;
> >>                       #address-cells = <1>;
> >>                       #size-cells = <1>;
> >>
> >>
> >> and document those in the prcmu binding?
> >>
> >> That would keep the code simpler and the same for both cases.
> >
> > I'm not sure you can. These addresses differ from platform to
> > platform, so I'd need to provide the base PRCMU address in
> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
> 
> Better ask on devicetree-discuss.
> 
> What it reflects are differences between SoC:s, so I think the
> right solution is to split it in a three-layer cake:
> 
> dbx5x0.dtsi -> included by
> db8500.dtsi -> included by
> snowball/hrefv60plus.dts
> 
> dbx5x0.dtsi -> included by
> dbx540.dtsi -> included by
> ccu9540/ccu8540.dts
> 
> Here you may insert the reg property into the node at the
> db8500.dtsi or dbx540.dtsi layer.

It's easy done, if that's the right way.

> If you prefer I can cook a patch...

... and I'm fine to do it.

[5 mins later]

Hmm... it appears that in STE's kernel, the same address is used for
all SoCs: 

  #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)

However, in Mainline there is another definition:

  #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)

... which doesn't seem to be in use anywhere - even for the u9540.

What's the deal big-man?

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

On Mon, 25 Mar 2013, Linus Walleij wrote:

> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:
> 
> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> >> >                                            "prcmu-tcpm");
> >> >         if (!res) {
> >> > -               dev_err(&pdev->dev,
> >> > -                       "Error: no prcmu tcpm memory region provided\n");
> >> > -               return;
> >> > -       }
> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
> >> > +               if (np) {
> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
> >> > +                                                      "prcmu-tcpm-per4");
> >> > +                       if (!tcpm_np) {
> >> > +                               dev_err(&pdev->dev,
> >> > +                                       "no prcmu tcpm mem region provided\n");
> >> > +                               return;
> >> > +                       }
> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
> >> > +               }
> >> > +       } else
> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
> >> > +
> >>
> >> Why don't you just add these extra registers to the prcmu node itself like
> >>
> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
> >> index 9de9309..6ee6c31 100644
> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
> >> @@ -191,8 +191,8 @@
> >>
> >>               prcmu: prcmu at 80157000 {
> >>                       compatible = "stericsson,db8500-prcmu";
> >> -                     reg = <0x80157000 0x1000>;
> >> -                     reg-names = "prcmu";
> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
> >>                       interrupts = <0 47 0x4>;
> >>                       #address-cells = <1>;
> >>                       #size-cells = <1>;
> >>
> >>
> >> and document those in the prcmu binding?
> >>
> >> That would keep the code simpler and the same for both cases.
> >
> > I'm not sure you can. These addresses differ from platform to
> > platform, so I'd need to provide the base PRCMU address in
> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
> 
> Better ask on devicetree-discuss.
> 
> What it reflects are differences between SoC:s, so I think the
> right solution is to split it in a three-layer cake:
> 
> dbx5x0.dtsi -> included by
> db8500.dtsi -> included by
> snowball/hrefv60plus.dts
> 
> dbx5x0.dtsi -> included by
> dbx540.dtsi -> included by
> ccu9540/ccu8540.dts
> 
> Here you may insert the reg property into the node at the
> db8500.dtsi or dbx540.dtsi layer.

It's easy done, if that's the right way.

> If you prefer I can cook a patch...

... and I'm fine to do it.

[5 mins later]

Hmm... it appears that in STE's kernel, the same address is used for
all SoCs: 

  #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)

However, in Mainline there is another definition:

  #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)

... which doesn't seem to be in use anywhere - even for the u9540.

What's the deal big-man?

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Linus Walleij]

On Tue, Mar 26, 2013 at 9:17 AM, Lee Jones <lee.jones@linaro.org> wrote:
> On Mon, 25 Mar 2013, Linus Walleij wrote:
>> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:
>>
>> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>> >> >                                            "prcmu-tcpm");
>> >> >         if (!res) {
>> >> > -               dev_err(&pdev->dev,
>> >> > -                       "Error: no prcmu tcpm memory region provided\n");
>> >> > -               return;
>> >> > -       }
>> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
>> >> > +               if (np) {
>> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
>> >> > +                                                      "prcmu-tcpm-per4");
>> >> > +                       if (!tcpm_np) {
>> >> > +                               dev_err(&pdev->dev,
>> >> > +                                       "no prcmu tcpm mem region provided\n");
>> >> > +                               return;
>> >> > +                       }
>> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
>> >> > +               }
>> >> > +       } else
>> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
>> >> > +
>> >>
>> >> Why don't you just add these extra registers to the prcmu node itself like
>> >>
>> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
>> >> index 9de9309..6ee6c31 100644
>> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
>> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
>> >> @@ -191,8 +191,8 @@
>> >>
>> >>               prcmu: prcmu@80157000 {
>> >>                       compatible = "stericsson,db8500-prcmu";
>> >> -                     reg = <0x80157000 0x1000>;
>> >> -                     reg-names = "prcmu";
>> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
>> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>> >>                       interrupts = <0 47 0x4>;
>> >>                       #address-cells = <1>;
>> >>                       #size-cells = <1>;
>> >>
>> >>
>> >> and document those in the prcmu binding?
>> >>
>> >> That would keep the code simpler and the same for both cases.
>> >
>> > I'm not sure you can. These addresses differ from platform to
>> > platform, so I'd need to provide the base PRCMU address in
>> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
>>
>> Better ask on devicetree-discuss.
>>
>> What it reflects are differences between SoC:s, so I think the
>> right solution is to split it in a three-layer cake:
>>
>> dbx5x0.dtsi -> included by
>> db8500.dtsi -> included by
>> snowball/hrefv60plus.dts
>>
>> dbx5x0.dtsi -> included by
>> dbx540.dtsi -> included by
>> ccu9540/ccu8540.dts
>>
>> Here you may insert the reg property into the node at the
>> db8500.dtsi or dbx540.dtsi layer.
>
> It's easy done, if that's the right way.
>
>> If you prefer I can cook a patch...
>
> ... and I'm fine to do it.
>
> [5 mins later]
>
> Hmm... it appears that in STE's kernel, the same address is used for
> all SoCs:
>
>   #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)

Yes that's correct...

> However, in Mainline there is another definition:
>
>   #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)
>
> ... which doesn't seem to be in use anywhere - even for the u9540.
>
> What's the deal big-man?

Probably there was another address at some point in some FPGA or
early silicon and it now needs fixing.

So you should be able to use the same thing on all ASICs, put one
single value in the dbx5x0.dtsi *and* fix this bug at the same time,
good!

Yours,
Linus Walleij

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Linus Walleij]

On Tue, Mar 26, 2013 at 9:17 AM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
> On Mon, 25 Mar 2013, Linus Walleij wrote:
>> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
>>
>> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>> >> >                                            "prcmu-tcpm");
>> >> >         if (!res) {
>> >> > -               dev_err(&pdev->dev,
>> >> > -                       "Error: no prcmu tcpm memory region provided\n");
>> >> > -               return;
>> >> > -       }
>> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
>> >> > +               if (np) {
>> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
>> >> > +                                                      "prcmu-tcpm-per4");
>> >> > +                       if (!tcpm_np) {
>> >> > +                               dev_err(&pdev->dev,
>> >> > +                                       "no prcmu tcpm mem region provided\n");
>> >> > +                               return;
>> >> > +                       }
>> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
>> >> > +               }
>> >> > +       } else
>> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
>> >> > +
>> >>
>> >> Why don't you just add these extra registers to the prcmu node itself like
>> >>
>> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
>> >> index 9de9309..6ee6c31 100644
>> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
>> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
>> >> @@ -191,8 +191,8 @@
>> >>
>> >>               prcmu: prcmu@80157000 {
>> >>                       compatible = "stericsson,db8500-prcmu";
>> >> -                     reg = <0x80157000 0x1000>;
>> >> -                     reg-names = "prcmu";
>> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
>> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>> >>                       interrupts = <0 47 0x4>;
>> >>                       #address-cells = <1>;
>> >>                       #size-cells = <1>;
>> >>
>> >>
>> >> and document those in the prcmu binding?
>> >>
>> >> That would keep the code simpler and the same for both cases.
>> >
>> > I'm not sure you can. These addresses differ from platform to
>> > platform, so I'd need to provide the base PRCMU address in
>> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
>>
>> Better ask on devicetree-discuss.
>>
>> What it reflects are differences between SoC:s, so I think the
>> right solution is to split it in a three-layer cake:
>>
>> dbx5x0.dtsi -> included by
>> db8500.dtsi -> included by
>> snowball/hrefv60plus.dts
>>
>> dbx5x0.dtsi -> included by
>> dbx540.dtsi -> included by
>> ccu9540/ccu8540.dts
>>
>> Here you may insert the reg property into the node at the
>> db8500.dtsi or dbx540.dtsi layer.
>
> It's easy done, if that's the right way.
>
>> If you prefer I can cook a patch...
>
> ... and I'm fine to do it.
>
> [5 mins later]
>
> Hmm... it appears that in STE's kernel, the same address is used for
> all SoCs:
>
>   #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)

Yes that's correct...

> However, in Mainline there is another definition:
>
>   #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)
>
> ... which doesn't seem to be in use anywhere - even for the u9540.
>
> What's the deal big-man?

Probably there was another address at some point in some FPGA or
early silicon and it now needs fixing.

So you should be able to use the same thing on all ASICs, put one
single value in the dbx5x0.dtsi *and* fix this bug at the same time,
good!

Yours,
Linus Walleij

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Linus Walleij]

On Tue, Mar 26, 2013 at 9:17 AM, Lee Jones <lee.jones@linaro.org> wrote:
> On Mon, 25 Mar 2013, Linus Walleij wrote:
>> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:
>>
>> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>> >> >                                            "prcmu-tcpm");
>> >> >         if (!res) {
>> >> > -               dev_err(&pdev->dev,
>> >> > -                       "Error: no prcmu tcpm memory region provided\n");
>> >> > -               return;
>> >> > -       }
>> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
>> >> > +               if (np) {
>> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
>> >> > +                                                      "prcmu-tcpm-per4");
>> >> > +                       if (!tcpm_np) {
>> >> > +                               dev_err(&pdev->dev,
>> >> > +                                       "no prcmu tcpm mem region provided\n");
>> >> > +                               return;
>> >> > +                       }
>> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
>> >> > +               }
>> >> > +       } else
>> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
>> >> > +
>> >>
>> >> Why don't you just add these extra registers to the prcmu node itself like
>> >>
>> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
>> >> index 9de9309..6ee6c31 100644
>> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
>> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
>> >> @@ -191,8 +191,8 @@
>> >>
>> >>               prcmu: prcmu at 80157000 {
>> >>                       compatible = "stericsson,db8500-prcmu";
>> >> -                     reg = <0x80157000 0x1000>;
>> >> -                     reg-names = "prcmu";
>> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
>> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
>> >>                       interrupts = <0 47 0x4>;
>> >>                       #address-cells = <1>;
>> >>                       #size-cells = <1>;
>> >>
>> >>
>> >> and document those in the prcmu binding?
>> >>
>> >> That would keep the code simpler and the same for both cases.
>> >
>> > I'm not sure you can. These addresses differ from platform to
>> > platform, so I'd need to provide the base PRCMU address in
>> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
>>
>> Better ask on devicetree-discuss.
>>
>> What it reflects are differences between SoC:s, so I think the
>> right solution is to split it in a three-layer cake:
>>
>> dbx5x0.dtsi -> included by
>> db8500.dtsi -> included by
>> snowball/hrefv60plus.dts
>>
>> dbx5x0.dtsi -> included by
>> dbx540.dtsi -> included by
>> ccu9540/ccu8540.dts
>>
>> Here you may insert the reg property into the node at the
>> db8500.dtsi or dbx540.dtsi layer.
>
> It's easy done, if that's the right way.
>
>> If you prefer I can cook a patch...
>
> ... and I'm fine to do it.
>
> [5 mins later]
>
> Hmm... it appears that in STE's kernel, the same address is used for
> all SoCs:
>
>   #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)

Yes that's correct...

> However, in Mainline there is another definition:
>
>   #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)
>
> ... which doesn't seem to be in use anywhere - even for the u9540.
>
> What's the deal big-man?

Probably there was another address at some point in some FPGA or
early silicon and it now needs fixing.

So you should be able to use the same thing on all ASICs, put one
single value in the dbx5x0.dtsi *and* fix this bug at the same time,
good!

Yours,
Linus Walleij

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

On Tue, 26 Mar 2013, Linus Walleij wrote:

> On Tue, Mar 26, 2013 at 9:17 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > On Mon, 25 Mar 2013, Linus Walleij wrote:
> >> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:
> >>
> >> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> >> >> >                                            "prcmu-tcpm");
> >> >> >         if (!res) {
> >> >> > -               dev_err(&pdev->dev,
> >> >> > -                       "Error: no prcmu tcpm memory region provided\n");
> >> >> > -               return;
> >> >> > -       }
> >> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
> >> >> > +               if (np) {
> >> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
> >> >> > +                                                      "prcmu-tcpm-per4");
> >> >> > +                       if (!tcpm_np) {
> >> >> > +                               dev_err(&pdev->dev,
> >> >> > +                                       "no prcmu tcpm mem region provided\n");
> >> >> > +                               return;
> >> >> > +                       }
> >> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
> >> >> > +               }
> >> >> > +       } else
> >> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
> >> >> > +
> >> >>
> >> >> Why don't you just add these extra registers to the prcmu node itself like
> >> >>
> >> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
> >> >> index 9de9309..6ee6c31 100644
> >> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
> >> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
> >> >> @@ -191,8 +191,8 @@
> >> >>
> >> >>               prcmu: prcmu@80157000 {
> >> >>                       compatible = "stericsson,db8500-prcmu";
> >> >> -                     reg = <0x80157000 0x1000>;
> >> >> -                     reg-names = "prcmu";
> >> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
> >> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
> >> >>                       interrupts = <0 47 0x4>;
> >> >>                       #address-cells = <1>;
> >> >>                       #size-cells = <1>;
> >> >>
> >> >>
> >> >> and document those in the prcmu binding?
> >> >>
> >> >> That would keep the code simpler and the same for both cases.
> >> >
> >> > I'm not sure you can. These addresses differ from platform to
> >> > platform, so I'd need to provide the base PRCMU address in
> >> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
> >>
> >> Better ask on devicetree-discuss.
> >>
> >> What it reflects are differences between SoC:s, so I think the
> >> right solution is to split it in a three-layer cake:
> >>
> >> dbx5x0.dtsi -> included by
> >> db8500.dtsi -> included by
> >> snowball/hrefv60plus.dts
> >>
> >> dbx5x0.dtsi -> included by
> >> dbx540.dtsi -> included by
> >> ccu9540/ccu8540.dts
> >>
> >> Here you may insert the reg property into the node at the
> >> db8500.dtsi or dbx540.dtsi layer.
> >
> > It's easy done, if that's the right way.
> >
> >> If you prefer I can cook a patch...
> >
> > ... and I'm fine to do it.
> >
> > [5 mins later]
> >
> > Hmm... it appears that in STE's kernel, the same address is used for
> > all SoCs:
> >
> >   #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)
> 
> Yes that's correct...
> 
> > However, in Mainline there is another definition:
> >
> >   #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)
> >
> > ... which doesn't seem to be in use anywhere - even for the u9540.
> >
> > What's the deal big-man?
> 
> Probably there was another address at some point in some FPGA or
> early silicon and it now needs fixing.
> 
> So you should be able to use the same thing on all ASICs, put one
> single value in the dbx5x0.dtsi *and* fix this bug at the same time,
> good!

Bit for information for you. 

I have confirmed that the address locations are the same for
all SoCs are the same. However, the size of the TCDM changes from 4k
on the db8500 to 12k on the db8540.

Is there a way we can increase the size for the db8540 without
creating an entire new DTS file? Seems overkill.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

On Tue, 26 Mar 2013, Linus Walleij wrote:

> On Tue, Mar 26, 2013 at 9:17 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > On Mon, 25 Mar 2013, Linus Walleij wrote:
> >> On Mon, Mar 25, 2013 at 5:46 PM, Lee Jones <lee.jones@linaro.org> wrote:
> >>
> >> >> >         res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> >> >> >                                            "prcmu-tcpm");
> >> >> >         if (!res) {
> >> >> > -               dev_err(&pdev->dev,
> >> >> > -                       "Error: no prcmu tcpm memory region provided\n");
> >> >> > -               return;
> >> >> > -       }
> >> >> > -       tcpm_base = ioremap(res->start, resource_size(res));
> >> >> > +               if (np) {
> >> >> > +                       tcpm_np = of_find_node_by_name(np->parent,
> >> >> > +                                                      "prcmu-tcpm-per4");
> >> >> > +                       if (!tcpm_np) {
> >> >> > +                               dev_err(&pdev->dev,
> >> >> > +                                       "no prcmu tcpm mem region provided\n");
> >> >> > +                               return;
> >> >> > +                       }
> >> >> > +                       tcpm_base = of_iomap(tcpm_np, 0);
> >> >> > +               }
> >> >> > +       } else
> >> >> > +               tcpm_base = ioremap(res->start, resource_size(res));
> >> >> > +
> >> >>
> >> >> Why don't you just add these extra registers to the prcmu node itself like
> >> >>
> >> >> diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi
> >> >> index 9de9309..6ee6c31 100644
> >> >> --- a/arch/arm/boot/dts/dbx5x0.dtsi
> >> >> +++ b/arch/arm/boot/dts/dbx5x0.dtsi
> >> >> @@ -191,8 +191,8 @@
> >> >>
> >> >>               prcmu: prcmu at 80157000 {
> >> >>                       compatible = "stericsson,db8500-prcmu";
> >> >> -                     reg = <0x80157000 0x1000>;
> >> >> -                     reg-names = "prcmu";
> >> >> +                     reg = <0x80157000 0x1000>, <0x801b0000 0x1000>, <0x801b8000 0x1000>;
> >> >> +                     reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm-per4";
> >> >>                       interrupts = <0 47 0x4>;
> >> >>                       #address-cells = <1>;
> >> >>                       #size-cells = <1>;
> >> >>
> >> >>
> >> >> and document those in the prcmu binding?
> >> >>
> >> >> That would keep the code simpler and the same for both cases.
> >> >
> >> > I'm not sure you can. These addresses differ from platform to
> >> > platform, so I'd need to provide the base PRCMU address in
> >> > dbx5x0.dtsi, then the other two in the dts files. Can you do that?
> >>
> >> Better ask on devicetree-discuss.
> >>
> >> What it reflects are differences between SoC:s, so I think the
> >> right solution is to split it in a three-layer cake:
> >>
> >> dbx5x0.dtsi -> included by
> >> db8500.dtsi -> included by
> >> snowball/hrefv60plus.dts
> >>
> >> dbx5x0.dtsi -> included by
> >> dbx540.dtsi -> included by
> >> ccu9540/ccu8540.dts
> >>
> >> Here you may insert the reg property into the node at the
> >> db8500.dtsi or dbx540.dtsi layer.
> >
> > It's easy done, if that's the right way.
> >
> >> If you prefer I can cook a patch...
> >
> > ... and I'm fine to do it.
> >
> > [5 mins later]
> >
> > Hmm... it appears that in STE's kernel, the same address is used for
> > all SoCs:
> >
> >   #define U8500_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x68000)
> 
> Yes that's correct...
> 
> > However, in Mainline there is another definition:
> >
> >   #define U9540_PRCMU_TCDM_BASE    (U8500_PER4_BASE + 0x6A000)
> >
> > ... which doesn't seem to be in use anywhere - even for the u9540.
> >
> > What's the deal big-man?
> 
> Probably there was another address at some point in some FPGA or
> early silicon and it now needs fixing.
> 
> So you should be able to use the same thing on all ASICs, put one
> single value in the dbx5x0.dtsi *and* fix this bug at the same time,
> good!

Bit for information for you. 

I have confirmed that the address locations are the same for
all SoCs are the same. However, the size of the TCDM changes from 4k
on the db8500 to 12k on the db8540.

Is there a way we can increase the size for the db8540 without
creating an entire new DTS file? Seems overkill.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Arnd Bergmann]

On Tuesday 26 March 2013, Lee Jones wrote:
> Bit for information for you. 
> 
> I have confirmed that the address locations are the same for
> all SoCs are the same. However, the size of the TCDM changes from 4k
> on the db8500 to 12k on the db8540.
> 
> Is there a way we can increase the size for the db8540 without
> creating an entire new DTS file? Seems overkill.

You can always override a property by setting it again, like

	soc {
		prcmu: db8500-prcmu@abcd0000 {
			reg = <0xabcd0000 0x1000>;
		};
	};

...


	&prcmu {
		reg = <0xabcd0000 0x3000>;
	}



	Arnd

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Arnd Bergmann]

On Tuesday 26 March 2013, Lee Jones wrote:
> Bit for information for you. 
> 
> I have confirmed that the address locations are the same for
> all SoCs are the same. However, the size of the TCDM changes from 4k
> on the db8500 to 12k on the db8540.
> 
> Is there a way we can increase the size for the db8540 without
> creating an entire new DTS file? Seems overkill.

You can always override a property by setting it again, like

	soc {
		prcmu: db8500-prcmu at abcd0000 {
			reg = <0xabcd0000 0x1000>;
		};
	};

...


	&prcmu {
		reg = <0xabcd0000 0x3000>;
	}



	Arnd

Re: [PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

On Tue, 26 Mar 2013, Arnd Bergmann wrote:

> On Tuesday 26 March 2013, Lee Jones wrote:
> > Bit for information for you. 
> > 
> > I have confirmed that the address locations are the same for
> > all SoCs are the same. However, the size of the TCDM changes from 4k
> > on the db8500 to 12k on the db8540.
> > 
> > Is there a way we can increase the size for the db8540 without
> > creating an entire new DTS file? Seems overkill.
> 
> You can always override a property by setting it again, like
> 
> 	soc {
> 		prcmu: db8500-prcmu@abcd0000 {
> 			reg = <0xabcd0000 0x1000>;
> 		};
> 	};
> 
> ...
> 
> 
> 	&prcmu {
> 		reg = <0xabcd0000 0x3000>;
> 	}

Perfect, thanks.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH 2/3] mfd: db8500-prcmu: Fetch the PRCMU TCDM base address from Device Tree

[Lee Jones]

On Tue, 26 Mar 2013, Arnd Bergmann wrote:

> On Tuesday 26 March 2013, Lee Jones wrote:
> > Bit for information for you. 
> > 
> > I have confirmed that the address locations are the same for
> > all SoCs are the same. However, the size of the TCDM changes from 4k
> > on the db8500 to 12k on the db8540.
> > 
> > Is there a way we can increase the size for the db8540 without
> > creating an entire new DTS file? Seems overkill.
> 
> You can always override a property by setting it again, like
> 
> 	soc {
> 		prcmu: db8500-prcmu at abcd0000 {
> 			reg = <0xabcd0000 0x1000>;
> 		};
> 	};
> 
> ...
> 
> 
> 	&prcmu {
> 		reg = <0xabcd0000 0x3000>;
> 	}

Perfect, thanks.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog