[PATCH net-next 00/11] tg3: misc patches - minor fixes and enhancements

[PATCH net-next 00/11] tg3: misc patches - minor fixes and enhancements

[Nithin Nayak Sujir]

This patchset contains minor fixes and enhancements (SGMII phy support and Link
Flap Avoidance). 

Michael Chan (3):
  tg3: Fix NVRAM size detection for the STM45PE20 pinstrap on 5762
    devices
  tg3: Add tg3_clear_mac_status() common function
  tg3: Add SGMII phy support for 5719/5718 serdes

Nithin Nayak Sujir (8):
  tg3: Fix flow control settings not propagated to hardware
  tg3: Remove unnecessary phy reset during ethtool commands
  tg3: Add a warning during link settings change if mgmt enabled
  tg3: Add support for link flap avoidance
  tg3: Pull the phy advertised speed and flow control settings on driver
    load
  tg3: Reset the phy to allow modified EEE settings to take effect
  tg3: Update version to 3.131
  MAINTAINERS: Update tg3 to reflect organizational changes

 MAINTAINERS                         |   2 +-
 drivers/net/ethernet/broadcom/tg3.c | 349 ++++++++++++++++++++++++++++++++----
 drivers/net/ethernet/broadcom/tg3.h |  12 ++
 3 files changed, 323 insertions(+), 40 deletions(-)

-- 
1.8.1.4

[PATCH net-next 01/11] tg3: Fix flow control settings not propagated to hardware

[Nithin Nayak Sujir]

In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting.  If flow control does not match, a relink is not necessary as
flow control is not a PHY setting.  Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index a4416b0..d044adf 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -4587,9 +4587,7 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 		} else {
 			if (!(bmcr & BMCR_ANENABLE) &&
 			    tp->link_config.speed == current_speed &&
-			    tp->link_config.duplex == current_duplex &&
-			    tp->link_config.flowctrl ==
-			    tp->link_config.active_flowctrl) {
+			    tp->link_config.duplex == current_duplex) {
 				current_link_up = 1;
 			}
 		}
-- 
1.8.1.4

[PATCH net-next 02/11] tg3: Fix NVRAM size detection for the STM45PE20 pinstrap on 5762 devices

[Nithin Nayak Sujir]

From: Michael Chan <mchan@broadcom.com>

The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index d044adf..a27310d 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -13986,6 +13986,12 @@ static void tg3_get_5720_nvram_info(struct tg3 *tp)
 		case FLASH_5762_EEPROM_LD:
 			nvmpinstrp = FLASH_5720_EEPROM_LD;
 			break;
+		case FLASH_5720VENDOR_M_ST_M45PE20:
+			/* This pinstrap supports multiple sizes, so force it
+			 * to read the actual size from location 0xf0.
+			 */
+			nvmpinstrp = FLASH_5720VENDOR_ST_45USPT;
+			break;
 		}
 	}
 
-- 
1.8.1.4

[PATCH net-next 03/11] tg3: Remove unnecessary phy reset during ethtool commands

[Nithin Nayak Sujir]

The current code unnecessarily resets the phy when we use ethtool to
change the ring parameters or flow control settings. Remove the phy
reset.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index a27310d..3f0d43f 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -11720,7 +11720,7 @@ static int tg3_set_ringparam(struct net_device *dev, struct ethtool_ringparam *e
 
 	if (netif_running(dev)) {
 		tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
-		err = tg3_restart_hw(tp, 1);
+		err = tg3_restart_hw(tp, 0);
 		if (!err)
 			tg3_netif_start(tp);
 	}
@@ -11841,7 +11841,7 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
 
 		if (netif_running(dev)) {
 			tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
-			err = tg3_restart_hw(tp, 1);
+			err = tg3_restart_hw(tp, 0);
 			if (!err)
 				tg3_netif_start(tp);
 		}
-- 
1.8.1.4

[PATCH net-next 04/11] tg3: Add a warning during link settings change if mgmt enabled

[Nithin Nayak Sujir]

When the user executes certain ethtool commands such as -s, -A, -G, -L,
-r a phy reset or autonegotiate is performed which results in management
traffic being interrupted.

Add a warning in these cases.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 3f0d43f..a744998 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -2531,6 +2531,13 @@ static void tg3_carrier_off(struct tg3 *tp)
 	tp->link_up = false;
 }
 
+static void tg3_warn_mgmt_link_flap(struct tg3 *tp)
+{
+	if (tg3_flag(tp, ENABLE_ASF))
+		netdev_warn(tp->dev,
+			    "Management side-band traffic will be interrupted during phy settings change\n");
+}
+
 /* This will reset the tigon3 PHY if there is no valid
  * link unless the FORCE argument is non-zero.
  */
@@ -11565,6 +11572,8 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 		tp->link_config.duplex = cmd->duplex;
 	}
 
+	tg3_warn_mgmt_link_flap(tp);
+
 	if (netif_running(dev))
 		tg3_setup_phy(tp, 1);
 
@@ -11643,6 +11652,8 @@ static int tg3_nway_reset(struct net_device *dev)
 	if (tp->phy_flags & TG3_PHYFLG_PHY_SERDES)
 		return -EINVAL;
 
+	tg3_warn_mgmt_link_flap(tp);
+
 	if (tg3_flag(tp, USE_PHYLIB)) {
 		if (!(tp->phy_flags & TG3_PHYFLG_IS_CONNECTED))
 			return -EAGAIN;
@@ -11755,6 +11766,9 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
 	struct tg3 *tp = netdev_priv(dev);
 	int err = 0;
 
+	if (tp->link_config.autoneg == AUTONEG_ENABLE)
+		tg3_warn_mgmt_link_flap(tp);
+
 	if (tg3_flag(tp, USE_PHYLIB)) {
 		u32 newadv;
 		struct phy_device *phydev;
-- 
1.8.1.4

[PATCH net-next 05/11] tg3: Add tg3_clear_mac_status() common function

[Nithin Nayak Sujir]

From: Michael Chan <mchan@broadcom.com>

Refactor for use in the next patch that adds sgmii phy support.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 30 ++++++++++++++----------------
 1 file changed, 14 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index a744998..568dd07 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -4428,6 +4428,18 @@ static bool tg3_test_and_report_link_chg(struct tg3 *tp, int curr_link_up)
 	return false;
 }
 
+static void tg3_clear_mac_status(struct tg3 *tp)
+{
+	tw32(MAC_EVENT, 0);
+
+	tw32_f(MAC_STATUS,
+	       MAC_STATUS_SYNC_CHANGED |
+	       MAC_STATUS_CFG_CHANGED |
+	       MAC_STATUS_MI_COMPLETION |
+	       MAC_STATUS_LNKSTATE_CHANGED);
+	udelay(40);
+}
+
 static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 {
 	int current_link_up;
@@ -4437,14 +4449,7 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 	u8 current_duplex;
 	int i, err;
 
-	tw32(MAC_EVENT, 0);
-
-	tw32_f(MAC_STATUS,
-	     (MAC_STATUS_SYNC_CHANGED |
-	      MAC_STATUS_CFG_CHANGED |
-	      MAC_STATUS_MI_COMPLETION |
-	      MAC_STATUS_LNKSTATE_CHANGED));
-	udelay(40);
+	tg3_clear_mac_status(tp);
 
 	if ((tp->mi_mode & MAC_MI_MODE_AUTO_POLL) != 0) {
 		tw32_f(MAC_MI_MODE,
@@ -5470,14 +5475,7 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 	tw32_f(MAC_MODE, tp->mac_mode);
 	udelay(40);
 
-	tw32(MAC_EVENT, 0);
-
-	tw32_f(MAC_STATUS,
-	     (MAC_STATUS_SYNC_CHANGED |
-	      MAC_STATUS_CFG_CHANGED |
-	      MAC_STATUS_MI_COMPLETION |
-	      MAC_STATUS_LNKSTATE_CHANGED));
-	udelay(40);
+	tg3_clear_mac_status(tp);
 
 	if (force_reset)
 		tg3_phy_reset(tp);
-- 
1.8.1.4

[PATCH net-next 06/11] tg3: Add SGMII phy support for 5719/5718 serdes

[Nithin Nayak Sujir]

From: Michael Chan <mchan@broadcom.com>

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 51 ++++++++++++++++++++++++++++++++-----
 drivers/net/ethernet/broadcom/tg3.h |  7 +++++
 2 files changed, 51 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 568dd07..f53e309 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -5465,11 +5465,50 @@ static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
 
 static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 {
-	int current_link_up, err = 0;
+	int current_link_up = 0, err = 0;
 	u32 bmsr, bmcr;
-	u16 current_speed;
-	u8 current_duplex;
-	u32 local_adv, remote_adv;
+	u16 current_speed = SPEED_UNKNOWN;
+	u8 current_duplex = DUPLEX_UNKNOWN;
+	u32 local_adv, remote_adv, sgsr;
+
+	if ((tg3_asic_rev(tp) == ASIC_REV_5719 ||
+	     tg3_asic_rev(tp) == ASIC_REV_5720) &&
+	     !tg3_readphy(tp, SERDES_TG3_1000X_STATUS, &sgsr) &&
+	     (sgsr & SERDES_TG3_SGMII_MODE)) {
+
+		if (force_reset)
+			tg3_phy_reset(tp);
+
+		tp->mac_mode &= ~MAC_MODE_PORT_MODE_MASK;
+
+		if (!(sgsr & SERDES_TG3_LINK_UP)) {
+			tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
+		} else {
+			current_link_up = 1;
+			if (sgsr & SERDES_TG3_SPEED_1000) {
+				current_speed = SPEED_1000;
+				tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
+			} else if (sgsr & SERDES_TG3_SPEED_100) {
+				current_speed = SPEED_100;
+				tp->mac_mode |= MAC_MODE_PORT_MODE_MII;
+			} else {
+				current_speed = SPEED_10;
+				tp->mac_mode |= MAC_MODE_PORT_MODE_MII;
+			}
+
+			if (sgsr & SERDES_TG3_FULL_DUPLEX)
+				current_duplex = DUPLEX_FULL;
+			else
+				current_duplex = DUPLEX_HALF;
+		}
+
+		tw32_f(MAC_MODE, tp->mac_mode);
+		udelay(40);
+
+		tg3_clear_mac_status(tp);
+
+		goto fiber_setup_done;
+	}
 
 	tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
 	tw32_f(MAC_MODE, tp->mac_mode);
@@ -5480,9 +5519,6 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 	if (force_reset)
 		tg3_phy_reset(tp);
 
-	current_link_up = 0;
-	current_speed = SPEED_UNKNOWN;
-	current_duplex = DUPLEX_UNKNOWN;
 	tp->link_config.rmt_adv = 0;
 
 	err |= tg3_readphy(tp, MII_BMSR, &bmsr);
@@ -5600,6 +5636,7 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 		}
 	}
 
+fiber_setup_done:
 	if (current_link_up == 1 && current_duplex == DUPLEX_FULL)
 		tg3_setup_flow_control(tp, local_adv, remote_adv);
 
diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h
index 1cdc1b6..fd00a38 100644
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -2371,6 +2371,13 @@
 #define MII_TG3_FET_SHDW_AUXSTAT2	0x1b
 #define  MII_TG3_FET_SHDW_AUXSTAT2_APD	0x0020
 
+/* Serdes PHY Register Definitions */
+#define SERDES_TG3_1000X_STATUS		0x14
+#define  SERDES_TG3_SGMII_MODE		 0x0001
+#define  SERDES_TG3_LINK_UP		 0x0002
+#define  SERDES_TG3_FULL_DUPLEX		 0x0004
+#define  SERDES_TG3_SPEED_100		 0x0008
+#define  SERDES_TG3_SPEED_1000		 0x0010
 
 /* APE registers.  Accessible through BAR1 */
 #define TG3_APE_GPIO_MSG		0x0008
-- 
1.8.1.4

[PATCH net-next 07/11] tg3: Add support for link flap avoidance

[Nithin Nayak Sujir]

This patch and the following two patches add support for link flap avoidance
by maintaining the link on power down. This feature is required for
management capable devices to have the management connection
uninterrupted on driver reload, reboot and interface up/down.

The other pros of this feature are
 - It speeds up boot up time by several seconds as DHCP addresses can be
   acquired faster.
 - It avoids lengthy Spanning Tree delay.

On powerup the hardware brings up the phy with default settings. If the
link is not up, the management software configures the phy to gigabit
and starts autonegotiate. Subsequently, as long as the link is up, the
driver and management refrain from resetting and/or changing any
configuration that the link depends on.

The LNK_FLAP_AVOID setting is an NVRAM user configurable bit and is
disabled by default.  If this setting is enabled, we skip powering down
the phy and resetting it.

A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
support for gigabit link speed when device is on auxiliary power.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 63 +++++++++++++++++++++++++++++++------
 drivers/net/ethernet/broadcom/tg3.h |  4 +++
 2 files changed, 58 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index f53e309..594a2f9 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -2933,6 +2933,9 @@ static void tg3_power_down_phy(struct tg3 *tp, bool do_low_power)
 {
 	u32 val;
 
+	if (tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN)
+		return;
+
 	if (tp->phy_flags & TG3_PHYFLG_PHY_SERDES) {
 		if (tg3_asic_rev(tp) == ASIC_REV_5704) {
 			u32 sg_dig_ctrl = tr32(SG_DIG_CTRL);
@@ -3996,7 +3999,13 @@ static int tg3_power_down_prepare(struct tg3 *tp)
 
 			if (tp->phy_flags & TG3_PHYFLG_MII_SERDES)
 				mac_mode = MAC_MODE_PORT_MODE_GMII;
-			else
+			else if (tp->phy_flags &
+				 TG3_PHYFLG_KEEP_LINK_ON_PWRDN) {
+				if (tp->link_config.active_speed == SPEED_1000)
+					mac_mode = MAC_MODE_PORT_MODE_GMII;
+				else
+					mac_mode = MAC_MODE_PORT_MODE_MII;
+			} else
 				mac_mode = MAC_MODE_PORT_MODE_MII;
 
 			mac_mode |= tp->mac_mode & MAC_MODE_LINK_POLARITY;
@@ -4250,12 +4259,16 @@ static void tg3_phy_copper_begin(struct tg3 *tp)
 	    (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)) {
 		u32 adv, fc;
 
-		if (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER) {
+		if ((tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER) &&
+		    !(tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN)) {
 			adv = ADVERTISED_10baseT_Half |
 			      ADVERTISED_10baseT_Full;
 			if (tg3_flag(tp, WOL_SPEED_100MB))
 				adv |= ADVERTISED_100baseT_Half |
 				       ADVERTISED_100baseT_Full;
+			if (tp->phy_flags & TG3_PHYFLG_1G_ON_VAUX_OK)
+				adv |= ADVERTISED_1000baseT_Half |
+				       ADVERTISED_1000baseT_Full;
 
 			fc = FLOW_CTRL_TX | FLOW_CTRL_RX;
 		} else {
@@ -4269,6 +4282,15 @@ static void tg3_phy_copper_begin(struct tg3 *tp)
 
 		tg3_phy_autoneg_cfg(tp, adv, fc);
 
+		if ((tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER) &&
+		    (tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN)) {
+			/* Normally during power down we want to autonegotiate
+			 * the lowest possible speed for WOL. However, to avoid
+			 * link flap, we leave it untouched.
+			 */
+			return;
+		}
+
 		tg3_writephy(tp, MII_BMCR,
 			     BMCR_ANENABLE | BMCR_ANRESTART);
 	} else {
@@ -8737,6 +8759,9 @@ static int tg3_chip_reset(struct tg3 *tp)
 
 	/* Reprobe ASF enable state.  */
 	tg3_flag_clear(tp, ENABLE_ASF);
+	tp->phy_flags &= ~(TG3_PHYFLG_1G_ON_VAUX_OK |
+			   TG3_PHYFLG_KEEP_LINK_ON_PWRDN);
+
 	tg3_flag_clear(tp, ASF_NEW_HANDSHAKE);
 	tg3_read_mem(tp, NIC_SRAM_DATA_SIG, &val);
 	if (val == NIC_SRAM_DATA_SIG_MAGIC) {
@@ -8748,6 +8773,12 @@ static int tg3_chip_reset(struct tg3 *tp)
 			tp->last_event_jiffies = jiffies;
 			if (tg3_flag(tp, 5750_PLUS))
 				tg3_flag_set(tp, ASF_NEW_HANDSHAKE);
+
+			tg3_read_mem(tp, NIC_SRAM_DATA_CFG_3, &nic_cfg);
+			if (nic_cfg & NIC_SRAM_1G_ON_VAUX_OK)
+				tp->phy_flags |= TG3_PHYFLG_1G_ON_VAUX_OK;
+			if (nic_cfg & NIC_SRAM_LNK_FLAP_AVOID)
+				tp->phy_flags |= TG3_PHYFLG_KEEP_LINK_ON_PWRDN;
 		}
 	}
 
@@ -11101,7 +11132,9 @@ static int tg3_open(struct net_device *dev)
 
 	tg3_full_unlock(tp);
 
-	err = tg3_start(tp, true, true, true);
+	err = tg3_start(tp,
+			!(tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN),
+			true, true);
 	if (err) {
 		tg3_frob_aux_power(tp, false);
 		pci_set_power_state(tp->pdev, PCI_D3hot);
@@ -14493,14 +14526,18 @@ static void tg3_get_eeprom_hw_cfg(struct tg3 *tp)
 		    (cfg2 & NIC_SRAM_DATA_CFG_2_APD_EN))
 			tp->phy_flags |= TG3_PHYFLG_ENABLE_APD;
 
-		if (tg3_flag(tp, PCI_EXPRESS) &&
-		    tg3_asic_rev(tp) != ASIC_REV_5785 &&
-		    !tg3_flag(tp, 57765_PLUS)) {
+		if (tg3_flag(tp, PCI_EXPRESS)) {
 			u32 cfg3;
 
 			tg3_read_mem(tp, NIC_SRAM_DATA_CFG_3, &cfg3);
-			if (cfg3 & NIC_SRAM_ASPM_DEBOUNCE)
+			if (tg3_asic_rev(tp) != ASIC_REV_5785 &&
+			    !tg3_flag(tp, 57765_PLUS) &&
+			    (cfg3 & NIC_SRAM_ASPM_DEBOUNCE))
 				tg3_flag_set(tp, ASPM_WORKAROUND);
+			if (cfg3 & NIC_SRAM_LNK_FLAP_AVOID)
+				tp->phy_flags |= TG3_PHYFLG_KEEP_LINK_ON_PWRDN;
+			if (cfg3 & NIC_SRAM_1G_ON_VAUX_OK)
+				tp->phy_flags |= TG3_PHYFLG_1G_ON_VAUX_OK;
 		}
 
 		if (cfg4 & NIC_SRAM_RGMII_INBAND_DISABLE)
@@ -14654,6 +14691,12 @@ static int tg3_phy_probe(struct tg3 *tp)
 		}
 	}
 
+	if (!tg3_flag(tp, ENABLE_ASF) &&
+	    !(tp->phy_flags & TG3_PHYFLG_ANY_SERDES) &&
+	    !(tp->phy_flags & TG3_PHYFLG_10_100_ONLY))
+		tp->phy_flags &= ~(TG3_PHYFLG_1G_ON_VAUX_OK |
+				   TG3_PHYFLG_KEEP_LINK_ON_PWRDN);
+
 	if (tg3_flag(tp, USE_PHYLIB))
 		return tg3_phy_init(tp);
 
@@ -14729,7 +14772,8 @@ static int tg3_phy_probe(struct tg3 *tp)
 
 	tg3_phy_init_link_config(tp);
 
-	if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES) &&
+	if (!(tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN) &&
+	    !(tp->phy_flags & TG3_PHYFLG_ANY_SERDES) &&
 	    !tg3_flag(tp, ENABLE_APE) &&
 	    !tg3_flag(tp, ENABLE_ASF)) {
 		u32 bmsr, dummy;
@@ -17296,7 +17340,8 @@ static int tg3_resume(struct device *device)
 	tg3_full_lock(tp, 0);
 
 	tg3_flag_set(tp, INIT_COMPLETE);
-	err = tg3_restart_hw(tp, 1);
+	err = tg3_restart_hw(tp,
+			     !(tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN));
 	if (err)
 		goto out;
 
diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h
index fd00a38..150bfc7 100644
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -2198,6 +2198,8 @@
 
 #define NIC_SRAM_DATA_CFG_3		0x00000d3c
 #define  NIC_SRAM_ASPM_DEBOUNCE		 0x00000002
+#define  NIC_SRAM_LNK_FLAP_AVOID	 0x00400000
+#define  NIC_SRAM_1G_ON_VAUX_OK		 0x00800000
 
 #define NIC_SRAM_DATA_CFG_4		0x00000d60
 #define  NIC_SRAM_GMII_MODE		 0x00000002
@@ -3305,6 +3307,8 @@ struct tg3 {
 #define TG3_PHYFLG_SERDES_PREEMPHASIS	0x00010000
 #define TG3_PHYFLG_PARALLEL_DETECT	0x00020000
 #define TG3_PHYFLG_EEE_CAP		0x00040000
+#define TG3_PHYFLG_1G_ON_VAUX_OK	0x00080000
+#define TG3_PHYFLG_KEEP_LINK_ON_PWRDN	0x00100000
 #define TG3_PHYFLG_MDIX_STATE		0x00200000
 
 	u32				led_ctrl;
-- 
1.8.1.4

[PATCH net-next 08/11] tg3: Pull the phy advertised speed and flow control settings on driver load

[Nithin Nayak Sujir]

Normally on driver load, we set the default settings for speed and flow
control. However, if the default setting is not compatible with the current link
state, we would autonegotiate and cause a link flap. To avoid this, we
pull the current advertised settings into the config.

A second scenario is if a user changes the speed/duplex/fc settings when
the interface is down. In this case we must not pull the settings from
the phy and overwrite user settings. We avoid that by checking the
USER_CONFIGURED flag.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 135 ++++++++++++++++++++++++++++++++++++
 drivers/net/ethernet/broadcom/tg3.h |   1 +
 2 files changed, 136 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 594a2f9..face04f 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -1874,6 +1874,20 @@ static void tg3_link_report(struct tg3 *tp)
 	tp->link_up = netif_carrier_ok(tp->dev);
 }
 
+static u32 tg3_decode_flowctrl_1000T(u32 adv)
+{
+	u32 flowctrl = 0;
+
+	if (adv & ADVERTISE_PAUSE_CAP) {
+		flowctrl |= FLOW_CTRL_RX;
+		if (!(adv & ADVERTISE_PAUSE_ASYM))
+			flowctrl |= FLOW_CTRL_TX;
+	} else if (adv & ADVERTISE_PAUSE_ASYM)
+		flowctrl |= FLOW_CTRL_TX;
+
+	return flowctrl;
+}
+
 static u16 tg3_advert_flowctrl_1000X(u8 flow_ctrl)
 {
 	u16 miireg;
@@ -1890,6 +1904,20 @@ static u16 tg3_advert_flowctrl_1000X(u8 flow_ctrl)
 	return miireg;
 }
 
+static u32 tg3_decode_flowctrl_1000X(u32 adv)
+{
+	u32 flowctrl = 0;
+
+	if (adv & ADVERTISE_1000XPAUSE) {
+		flowctrl |= FLOW_CTRL_RX;
+		if (!(adv & ADVERTISE_1000XPSE_ASYM))
+			flowctrl |= FLOW_CTRL_TX;
+	} else if (adv & ADVERTISE_1000XPSE_ASYM)
+		flowctrl |= FLOW_CTRL_TX;
+
+	return flowctrl;
+}
+
 static u8 tg3_resolve_flowctrl_1000X(u16 lcladv, u16 rmtadv)
 {
 	u8 cap = 0;
@@ -4347,6 +4375,103 @@ static void tg3_phy_copper_begin(struct tg3 *tp)
 	}
 }
 
+static int tg3_phy_pull_config(struct tg3 *tp)
+{
+	int err;
+	u32 val;
+
+	err = tg3_readphy(tp, MII_BMCR, &val);
+	if (err)
+		goto done;
+
+	if (!(val & BMCR_ANENABLE)) {
+		tp->link_config.autoneg = AUTONEG_DISABLE;
+		tp->link_config.advertising = 0;
+		tg3_flag_clear(tp, PAUSE_AUTONEG);
+
+		err = -EIO;
+
+		switch (val & (BMCR_SPEED1000 | BMCR_SPEED100)) {
+		case 0:
+			if (tp->phy_flags & TG3_PHYFLG_ANY_SERDES)
+				goto done;
+
+			tp->link_config.speed = SPEED_10;
+			break;
+		case BMCR_SPEED100:
+			if (tp->phy_flags & TG3_PHYFLG_ANY_SERDES)
+				goto done;
+
+			tp->link_config.speed = SPEED_100;
+			break;
+		case BMCR_SPEED1000:
+			if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
+				tp->link_config.speed = SPEED_1000;
+				break;
+			}
+			/* Fall through */
+		default:
+			goto done;
+		}
+
+		if (val & BMCR_FULLDPLX)
+			tp->link_config.duplex = DUPLEX_FULL;
+		else
+			tp->link_config.duplex = DUPLEX_HALF;
+
+		tp->link_config.flowctrl = FLOW_CTRL_RX | FLOW_CTRL_TX;
+
+		err = 0;
+		goto done;
+	}
+
+	tp->link_config.autoneg = AUTONEG_ENABLE;
+	tp->link_config.advertising = ADVERTISED_Autoneg;
+	tg3_flag_set(tp, PAUSE_AUTONEG);
+
+	if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES)) {
+		u32 adv;
+
+		err = tg3_readphy(tp, MII_ADVERTISE, &val);
+		if (err)
+			goto done;
+
+		adv = mii_adv_to_ethtool_adv_t(val & ADVERTISE_ALL);
+		tp->link_config.advertising |= adv | ADVERTISED_TP;
+
+		tp->link_config.flowctrl = tg3_decode_flowctrl_1000T(val);
+	} else {
+		tp->link_config.advertising |= ADVERTISED_FIBRE;
+	}
+
+	if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
+		u32 adv;
+
+		if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES)) {
+			err = tg3_readphy(tp, MII_CTRL1000, &val);
+			if (err)
+				goto done;
+
+			adv = mii_ctrl1000_to_ethtool_adv_t(val);
+		} else {
+			err = tg3_readphy(tp, MII_ADVERTISE, &val);
+			if (err)
+				goto done;
+
+			adv = tg3_decode_flowctrl_1000X(val);
+			tp->link_config.flowctrl = adv;
+
+			val &= (ADVERTISE_1000XHALF | ADVERTISE_1000XFULL);
+			adv = mii_adv_to_ethtool_adv_x(val);
+		}
+
+		tp->link_config.advertising |= adv;
+	}
+
+done:
+	return err;
+}
+
 static int tg3_init_5401phy_dsp(struct tg3 *tp)
 {
 	int err;
@@ -9313,6 +9438,12 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 		       TG3_CPMU_DBTMR2_TXIDXEQ_2047US);
 	}
 
+	if ((tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN) &&
+	    !(tp->phy_flags & TG3_PHYFLG_USER_CONFIGURED)) {
+		tg3_phy_pull_config(tp);
+		tp->phy_flags |= TG3_PHYFLG_USER_CONFIGURED;
+	}
+
 	if (reset_phy)
 		tg3_phy_reset(tp);
 
@@ -11640,6 +11771,8 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 		tp->link_config.duplex = cmd->duplex;
 	}
 
+	tp->phy_flags |= TG3_PHYFLG_USER_CONFIGURED;
+
 	tg3_warn_mgmt_link_flap(tp);
 
 	if (netif_running(dev))
@@ -11931,6 +12064,8 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
 		tg3_full_unlock(tp);
 	}
 
+	tp->phy_flags |= TG3_PHYFLG_USER_CONFIGURED;
+
 	return err;
 }
 
diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h
index 150bfc7..9b2d3ac 100644
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -3290,6 +3290,7 @@ struct tg3 {
 #define TG3_PHYFLG_IS_LOW_POWER		0x00000001
 #define TG3_PHYFLG_IS_CONNECTED		0x00000002
 #define TG3_PHYFLG_USE_MI_INTERRUPT	0x00000004
+#define TG3_PHYFLG_USER_CONFIGURED	0x00000008
 #define TG3_PHYFLG_PHY_SERDES		0x00000010
 #define TG3_PHYFLG_MII_SERDES		0x00000020
 #define TG3_PHYFLG_ANY_SERDES		(TG3_PHYFLG_PHY_SERDES |	\
-- 
1.8.1.4

[PATCH net-next 09/11] tg3: Reset the phy to allow modified EEE settings to take effect

[Nithin Nayak Sujir]

When LFA is enabled, we don't reset the phy. But EEE settings changes
don't take effect until the phy is reset. Add a phy reset when we detect
a changed EEE setting.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 38 +++++++++++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index face04f..2bd2213 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -4491,6 +4491,32 @@ static int tg3_init_5401phy_dsp(struct tg3 *tp)
 	return err;
 }
 
+static bool tg3_phy_eee_config_ok(struct tg3 *tp)
+{
+	u32 val;
+	u32 tgtadv = 0;
+	u32 advertising = tp->link_config.advertising;
+
+	if (!(tp->phy_flags & TG3_PHYFLG_EEE_CAP))
+		return true;
+
+	if (tg3_phy_cl45_read(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV, &val))
+		return false;
+
+	val &= (MDIO_AN_EEE_ADV_100TX | MDIO_AN_EEE_ADV_1000T);
+
+
+	if (advertising & ADVERTISED_100baseT_Full)
+		tgtadv |= MDIO_AN_EEE_ADV_100TX;
+	if (advertising & ADVERTISED_1000baseT_Full)
+		tgtadv |= MDIO_AN_EEE_ADV_1000T;
+
+	if (val != tgtadv)
+		return false;
+
+	return true;
+}
+
 static bool tg3_phy_copper_an_config_ok(struct tg3 *tp, u32 *lcladv)
 {
 	u32 advmsk, tgtadv, advertising;
@@ -4739,10 +4765,22 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 		tp->link_config.active_duplex = current_duplex;
 
 		if (tp->link_config.autoneg == AUTONEG_ENABLE) {
+			bool eee_config_ok = tg3_phy_eee_config_ok(tp);
+
 			if ((bmcr & BMCR_ANENABLE) &&
+			    eee_config_ok &&
 			    tg3_phy_copper_an_config_ok(tp, &lcl_adv) &&
 			    tg3_phy_copper_fetch_rmtadv(tp, &rmt_adv))
 				current_link_up = 1;
+
+			/* EEE settings changes take effect only after a phy
+			 * reset.  If we have skipped a reset due to Link Flap
+			 * Avoidance being enabled, do it now.
+			 */
+			if (!eee_config_ok &&
+			    (tp->phy_flags & TG3_PHYFLG_KEEP_LINK_ON_PWRDN) &&
+			    !force_reset)
+				tg3_phy_reset(tp);
 		} else {
 			if (!(bmcr & BMCR_ANENABLE) &&
 			    tp->link_config.speed == current_speed &&
-- 
1.8.1.4

[PATCH net-next 10/11] tg3: Update version to 3.131

[Nithin Nayak Sujir]

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/tg3.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 2bd2213..0fe6444 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -94,10 +94,10 @@ static inline void _tg3_flag_clear(enum TG3_FLAGS flag, unsigned long *bits)
 
 #define DRV_MODULE_NAME		"tg3"
 #define TG3_MAJ_NUM			3
-#define TG3_MIN_NUM			130
+#define TG3_MIN_NUM			131
 #define DRV_MODULE_VERSION	\
 	__stringify(TG3_MAJ_NUM) "." __stringify(TG3_MIN_NUM)
-#define DRV_MODULE_RELDATE	"February 14, 2013"
+#define DRV_MODULE_RELDATE	"April 09, 2013"
 
 #define RESET_KIND_SHUTDOWN	0
 #define RESET_KIND_INIT		1
-- 
1.8.1.4

[PATCH net-next 11/11] MAINTAINERS: Update tg3 to reflect organizational changes

[Nithin Nayak Sujir]

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
---
 MAINTAINERS | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index d3a888c..5d0e581 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1764,7 +1764,7 @@ F:	arch/arm/configs/bcm2835_defconfig
 F:	drivers/*/*bcm2835*
 
 BROADCOM TG3 GIGABIT ETHERNET DRIVER
-M:	Matt Carlson <mcarlson@broadcom.com>
+M:	Nithin Nayak Sujir <nsujir@broadcom.com>
 M:	Michael Chan <mchan@broadcom.com>
 L:	netdev@vger.kernel.org
 S:	Supported
-- 
1.8.1.4

Re: [PATCH net-next 07/11] tg3: Add support for link flap avoidance

[David Miller]

From: "Nithin Nayak Sujir" <nsujir@broadcom.com>
Date: Tue, 9 Apr 2013 11:48:07 -0700

> This patch and the following two patches add support for link flap avoidance
> by maintaining the link on power down. This feature is required for
> management capable devices to have the management connection
> uninterrupted on driver reload, reboot and interface up/down.
> 
> The other pros of this feature are
>  - It speeds up boot up time by several seconds as DHCP addresses can be
>    acquired faster.
>  - It avoids lengthy Spanning Tree delay.
> 
> On powerup the hardware brings up the phy with default settings. If the
> link is not up, the management software configures the phy to gigabit
> and starts autonegotiate. Subsequently, as long as the link is up, the
> driver and management refrain from resetting and/or changing any
> configuration that the link depends on.
> 
> The LNK_FLAP_AVOID setting is an NVRAM user configurable bit and is
> disabled by default.  If this setting is enabled, we skip powering down
> the phy and resetting it.
> 
> A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
> support for gigabit link speed when device is on auxiliary power.
> 
> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
> Signed-off-by: Michael Chan <mchan@broadcom.com>

Looks good, all applied, thanks.

If we force a PHY reset due to EEE changes, will the ASF traffic
disruption warning message be emitted?

[PATCH net-next] tg3: Use bool not int

[Joe Perches]

Using bool can make code more readable.

Convert uses and tests of int to bool.

This also makes a comparison of tg3->link_up
(itself bool) a bool comparison instead of int.

Reorder stack variable declarations to make
bool fit declaration holes where appropriate.

$ size drivers/net/ethernet/broadcom/tg3.o*
   text	   data	    bss	    dec	    hex	filename
 169958	  27249	  58896	 256103	  3e867	drivers/net/ethernet/broadcom/tg3.o.new
 169968	  27249	  58896	 256113	  3e871	drivers/net/ethernet/broadcom/tg3.o.old

Signed-off-by: Joe Perches <joe@perches.com>
---

Reduces allyesconfig object size 10 bytes! (wow!!)

 drivers/net/ethernet/broadcom/tg3.c | 157 ++++++++++++++++++------------------
 1 file changed, 80 insertions(+), 77 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index 0fe6444..ce98572 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -2228,7 +2228,7 @@ static void tg3_phy_toggle_apd(struct tg3 *tp, bool enable)
 	tg3_writephy(tp, MII_TG3_MISC_SHDW, reg);
 }
 
-static void tg3_phy_toggle_automdix(struct tg3 *tp, int enable)
+static void tg3_phy_toggle_automdix(struct tg3 *tp, bool enable)
 {
 	u32 phy;
 
@@ -2320,7 +2320,7 @@ static void tg3_phy_apply_otp(struct tg3 *tp)
 	tg3_phy_toggle_auxctl_smdsp(tp, false);
 }
 
-static void tg3_phy_eee_adjust(struct tg3 *tp, u32 current_link_up)
+static void tg3_phy_eee_adjust(struct tg3 *tp, bool current_link_up)
 {
 	u32 val;
 
@@ -2330,7 +2330,7 @@ static void tg3_phy_eee_adjust(struct tg3 *tp, u32 current_link_up)
 	tp->setlpicnt = 0;
 
 	if (tp->link_config.autoneg == AUTONEG_ENABLE &&
-	    current_link_up == 1 &&
+	    current_link_up &&
 	    tp->link_config.active_duplex == DUPLEX_FULL &&
 	    (tp->link_config.active_speed == SPEED_100 ||
 	     tp->link_config.active_speed == SPEED_1000)) {
@@ -2352,7 +2352,7 @@ static void tg3_phy_eee_adjust(struct tg3 *tp, u32 current_link_up)
 	}
 
 	if (!tp->setlpicnt) {
-		if (current_link_up == 1 &&
+		if (current_link_up &&
 		   !tg3_phy_toggle_auxctl_smdsp(tp, true)) {
 			tg3_phydsp_write(tp, MII_TG3_DSP_TAP26, 0x0000);
 			tg3_phy_toggle_auxctl_smdsp(tp, false);
@@ -2705,7 +2705,7 @@ out:
 	if (tg3_chip_rev_id(tp) == CHIPREV_ID_5762_A0)
 		tg3_phydsp_write(tp, 0xffb, 0x4000);
 
-	tg3_phy_toggle_automdix(tp, 1);
+	tg3_phy_toggle_automdix(tp, true);
 	tg3_phy_set_wirespeed(tp);
 	return 0;
 }
@@ -3851,7 +3851,7 @@ static int tg3_load_tso_firmware(struct tg3 *tp)
 
 
 /* tp->lock is held. */
-static void __tg3_set_mac_addr(struct tg3 *tp, int skip_mac_1)
+static void __tg3_set_mac_addr(struct tg3 *tp, bool skip_mac_1)
 {
 	u32 addr_high, addr_low;
 	int i;
@@ -3914,7 +3914,7 @@ static int tg3_power_up(struct tg3 *tp)
 	return err;
 }
 
-static int tg3_setup_phy(struct tg3 *, int);
+static int tg3_setup_phy(struct tg3 *, bool);
 
 static int tg3_power_down_prepare(struct tg3 *tp)
 {
@@ -3986,7 +3986,7 @@ static int tg3_power_down_prepare(struct tg3 *tp)
 			tp->phy_flags |= TG3_PHYFLG_IS_LOW_POWER;
 
 		if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES))
-			tg3_setup_phy(tp, 0);
+			tg3_setup_phy(tp, false);
 	}
 
 	if (tg3_asic_rev(tp) == ASIC_REV_5906) {
@@ -4583,7 +4583,7 @@ static bool tg3_phy_copper_fetch_rmtadv(struct tg3 *tp, u32 *rmtadv)
 	return true;
 }
 
-static bool tg3_test_and_report_link_chg(struct tg3 *tp, int curr_link_up)
+static bool tg3_test_and_report_link_chg(struct tg3 *tp, bool curr_link_up)
 {
 	if (curr_link_up != tp->link_up) {
 		if (curr_link_up) {
@@ -4613,9 +4613,9 @@ static void tg3_clear_mac_status(struct tg3 *tp)
 	udelay(40);
 }
 
-static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
+static int tg3_setup_copper_phy(struct tg3 *tp, bool force_reset)
 {
-	int current_link_up;
+	bool current_link_up;
 	u32 bmsr, val;
 	u32 lcl_adv, rmt_adv;
 	u16 current_speed;
@@ -4642,7 +4642,7 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 		tg3_readphy(tp, MII_BMSR, &bmsr);
 		if (!tg3_readphy(tp, MII_BMSR, &bmsr) &&
 		    !(bmsr & BMSR_LSTATUS))
-			force_reset = 1;
+			force_reset = true;
 	}
 	if (force_reset)
 		tg3_phy_reset(tp);
@@ -4706,7 +4706,7 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 			tg3_writephy(tp, MII_TG3_EXT_CTRL, 0);
 	}
 
-	current_link_up = 0;
+	current_link_up = false;
 	current_speed = SPEED_UNKNOWN;
 	current_duplex = DUPLEX_UNKNOWN;
 	tp->phy_flags &= ~TG3_PHYFLG_MDIX_STATE;
@@ -4771,7 +4771,7 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 			    eee_config_ok &&
 			    tg3_phy_copper_an_config_ok(tp, &lcl_adv) &&
 			    tg3_phy_copper_fetch_rmtadv(tp, &rmt_adv))
-				current_link_up = 1;
+				current_link_up = true;
 
 			/* EEE settings changes take effect only after a phy
 			 * reset.  If we have skipped a reset due to Link Flap
@@ -4785,11 +4785,11 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 			if (!(bmcr & BMCR_ANENABLE) &&
 			    tp->link_config.speed == current_speed &&
 			    tp->link_config.duplex == current_duplex) {
-				current_link_up = 1;
+				current_link_up = true;
 			}
 		}
 
-		if (current_link_up == 1 &&
+		if (current_link_up &&
 		    tp->link_config.active_duplex == DUPLEX_FULL) {
 			u32 reg, bit;
 
@@ -4809,11 +4809,11 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
 	}
 
 relink:
-	if (current_link_up == 0 || (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)) {
+	if (!current_link_up || (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)) {
 		tg3_phy_copper_begin(tp);
 
 		if (tg3_flag(tp, ROBOSWITCH)) {
-			current_link_up = 1;
+			current_link_up = true;
 			/* FIXME: when BCM5325 switch is used use 100 MBit/s */
 			current_speed = SPEED_1000;
 			current_duplex = DUPLEX_FULL;
@@ -4824,11 +4824,11 @@ relink:
 		tg3_readphy(tp, MII_BMSR, &bmsr);
 		if ((!tg3_readphy(tp, MII_BMSR, &bmsr) && (bmsr & BMSR_LSTATUS)) ||
 		    (tp->mac_mode & MAC_MODE_PORT_INT_LPBACK))
-			current_link_up = 1;
+			current_link_up = true;
 	}
 
 	tp->mac_mode &= ~MAC_MODE_PORT_MODE_MASK;
-	if (current_link_up == 1) {
+	if (current_link_up) {
 		if (tp->link_config.active_speed == SPEED_100 ||
 		    tp->link_config.active_speed == SPEED_10)
 			tp->mac_mode |= MAC_MODE_PORT_MODE_MII;
@@ -4864,7 +4864,7 @@ relink:
 		tp->mac_mode |= MAC_MODE_HALF_DUPLEX;
 
 	if (tg3_asic_rev(tp) == ASIC_REV_5700) {
-		if (current_link_up == 1 &&
+		if (current_link_up &&
 		    tg3_5700_link_polarity(tp, tp->link_config.active_speed))
 			tp->mac_mode |= MAC_MODE_LINK_POLARITY;
 		else
@@ -4895,7 +4895,7 @@ relink:
 	udelay(40);
 
 	if (tg3_asic_rev(tp) == ASIC_REV_5700 &&
-	    current_link_up == 1 &&
+	    current_link_up &&
 	    tp->link_config.active_speed == SPEED_1000 &&
 	    (tg3_flag(tp, PCIX_MODE) || tg3_flag(tp, PCI_HIGH_SPEED))) {
 		udelay(120);
@@ -5335,19 +5335,19 @@ static void tg3_init_bcm8002(struct tg3 *tp)
 	tg3_writephy(tp, 0x10, 0x8011);
 }
 
-static int tg3_setup_fiber_hw_autoneg(struct tg3 *tp, u32 mac_status)
+static bool tg3_setup_fiber_hw_autoneg(struct tg3 *tp, u32 mac_status)
 {
 	u16 flowctrl;
+	bool current_link_up;
 	u32 sg_dig_ctrl, sg_dig_status;
 	u32 serdes_cfg, expected_sg_dig_ctrl;
 	int workaround, port_a;
-	int current_link_up;
 
 	serdes_cfg = 0;
 	expected_sg_dig_ctrl = 0;
 	workaround = 0;
 	port_a = 1;
-	current_link_up = 0;
+	current_link_up = false;
 
 	if (tg3_chip_rev_id(tp) != CHIPREV_ID_5704_A0 &&
 	    tg3_chip_rev_id(tp) != CHIPREV_ID_5704_A1) {
@@ -5378,7 +5378,7 @@ static int tg3_setup_fiber_hw_autoneg(struct tg3 *tp, u32 mac_status)
 		}
 		if (mac_status & MAC_STATUS_PCS_SYNCED) {
 			tg3_setup_flow_control(tp, 0, 0);
-			current_link_up = 1;
+			current_link_up = true;
 		}
 		goto out;
 	}
@@ -5399,7 +5399,7 @@ static int tg3_setup_fiber_hw_autoneg(struct tg3 *tp, u32 mac_status)
 				    MAC_STATUS_RCVD_CFG)) ==
 		     MAC_STATUS_PCS_SYNCED)) {
 			tp->serdes_counter--;
-			current_link_up = 1;
+			current_link_up = true;
 			goto out;
 		}
 restart_autoneg:
@@ -5434,7 +5434,7 @@ restart_autoneg:
 					   mii_adv_to_ethtool_adv_x(remote_adv);
 
 			tg3_setup_flow_control(tp, local_adv, remote_adv);
-			current_link_up = 1;
+			current_link_up = true;
 			tp->serdes_counter = 0;
 			tp->phy_flags &= ~TG3_PHYFLG_PARALLEL_DETECT;
 		} else if (!(sg_dig_status & SG_DIG_AUTONEG_COMPLETE)) {
@@ -5462,7 +5462,7 @@ restart_autoneg:
 				if ((mac_status & MAC_STATUS_PCS_SYNCED) &&
 				    !(mac_status & MAC_STATUS_RCVD_CFG)) {
 					tg3_setup_flow_control(tp, 0, 0);
-					current_link_up = 1;
+					current_link_up = true;
 					tp->phy_flags |=
 						TG3_PHYFLG_PARALLEL_DETECT;
 					tp->serdes_counter =
@@ -5480,9 +5480,9 @@ out:
 	return current_link_up;
 }
 
-static int tg3_setup_fiber_by_hand(struct tg3 *tp, u32 mac_status)
+static bool tg3_setup_fiber_by_hand(struct tg3 *tp, u32 mac_status)
 {
-	int current_link_up = 0;
+	bool current_link_up = false;
 
 	if (!(mac_status & MAC_STATUS_PCS_SYNCED))
 		goto out;
@@ -5509,7 +5509,7 @@ static int tg3_setup_fiber_by_hand(struct tg3 *tp, u32 mac_status)
 
 			tg3_setup_flow_control(tp, local_adv, remote_adv);
 
-			current_link_up = 1;
+			current_link_up = true;
 		}
 		for (i = 0; i < 30; i++) {
 			udelay(20);
@@ -5524,15 +5524,15 @@ static int tg3_setup_fiber_by_hand(struct tg3 *tp, u32 mac_status)
 		}
 
 		mac_status = tr32(MAC_STATUS);
-		if (current_link_up == 0 &&
+		if (!current_link_up &&
 		    (mac_status & MAC_STATUS_PCS_SYNCED) &&
 		    !(mac_status & MAC_STATUS_RCVD_CFG))
-			current_link_up = 1;
+			current_link_up = true;
 	} else {
 		tg3_setup_flow_control(tp, 0, 0);
 
 		/* Forcing 1000FD link up. */
-		current_link_up = 1;
+		current_link_up = true;
 
 		tw32_f(MAC_MODE, (tp->mac_mode | MAC_MODE_SEND_CONFIGS));
 		udelay(40);
@@ -5545,13 +5545,13 @@ out:
 	return current_link_up;
 }
 
-static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
+static int tg3_setup_fiber_phy(struct tg3 *tp, bool force_reset)
 {
 	u32 orig_pause_cfg;
 	u16 orig_active_speed;
 	u8 orig_active_duplex;
 	u32 mac_status;
-	int current_link_up;
+	bool current_link_up;
 	int i;
 
 	orig_pause_cfg = tp->link_config.active_flowctrl;
@@ -5588,7 +5588,7 @@ static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
 	tw32_f(MAC_EVENT, MAC_EVENT_LNKSTATE_CHANGED);
 	udelay(40);
 
-	current_link_up = 0;
+	current_link_up = false;
 	tp->link_config.rmt_adv = 0;
 	mac_status = tr32(MAC_STATUS);
 
@@ -5613,7 +5613,7 @@ static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
 
 	mac_status = tr32(MAC_STATUS);
 	if ((mac_status & MAC_STATUS_PCS_SYNCED) == 0) {
-		current_link_up = 0;
+		current_link_up = false;
 		if (tp->link_config.autoneg == AUTONEG_ENABLE &&
 		    tp->serdes_counter == 0) {
 			tw32_f(MAC_MODE, (tp->mac_mode |
@@ -5623,7 +5623,7 @@ static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
 		}
 	}
 
-	if (current_link_up == 1) {
+	if (current_link_up) {
 		tp->link_config.active_speed = SPEED_1000;
 		tp->link_config.active_duplex = DUPLEX_FULL;
 		tw32(MAC_LED_CTRL, (tp->led_ctrl |
@@ -5648,12 +5648,13 @@ static int tg3_setup_fiber_phy(struct tg3 *tp, int force_reset)
 	return 0;
 }
 
-static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
+static int tg3_setup_fiber_mii_phy(struct tg3 *tp, bool force_reset)
 {
-	int current_link_up = 0, err = 0;
+	int err = 0;
 	u32 bmsr, bmcr;
 	u16 current_speed = SPEED_UNKNOWN;
 	u8 current_duplex = DUPLEX_UNKNOWN;
+	bool current_link_up = false;
 	u32 local_adv, remote_adv, sgsr;
 
 	if ((tg3_asic_rev(tp) == ASIC_REV_5719 ||
@@ -5669,7 +5670,7 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 		if (!(sgsr & SERDES_TG3_LINK_UP)) {
 			tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
 		} else {
-			current_link_up = 1;
+			current_link_up = true;
 			if (sgsr & SERDES_TG3_SPEED_1000) {
 				current_speed = SPEED_1000;
 				tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
@@ -5789,7 +5790,7 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 
 	if (bmsr & BMSR_LSTATUS) {
 		current_speed = SPEED_1000;
-		current_link_up = 1;
+		current_link_up = true;
 		if (bmcr & BMCR_FULLDPLX)
 			current_duplex = DUPLEX_FULL;
 		else
@@ -5816,13 +5817,13 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
 			} else if (!tg3_flag(tp, 5780_CLASS)) {
 				/* Link is up via parallel detect */
 			} else {
-				current_link_up = 0;
+				current_link_up = false;
 			}
 		}
 	}
 
 fiber_setup_done:
-	if (current_link_up == 1 && current_duplex == DUPLEX_FULL)
+	if (current_link_up && current_duplex == DUPLEX_FULL)
 		tg3_setup_flow_control(tp, local_adv, remote_adv);
 
 	tp->mac_mode &= ~MAC_MODE_HALF_DUPLEX;
@@ -5901,7 +5902,7 @@ static void tg3_serdes_parallel_detect(struct tg3 *tp)
 	}
 }
 
-static int tg3_setup_phy(struct tg3 *tp, int force_reset)
+static int tg3_setup_phy(struct tg3 *tp, bool force_reset)
 {
 	u32 val;
 	int err;
@@ -6802,7 +6803,7 @@ static void tg3_poll_link(struct tg3 *tp)
 				      MAC_STATUS_LNKSTATE_CHANGED));
 				udelay(40);
 			} else
-				tg3_setup_phy(tp, 0);
+				tg3_setup_phy(tp, false);
 			spin_unlock(&tp->lock);
 		}
 	}
@@ -7899,7 +7900,7 @@ static int tg3_phy_lpbk_set(struct tg3 *tp, u32 speed, bool extlpbk)
 	u32 val, bmcr, mac_mode, ptest = 0;
 
 	tg3_phy_toggle_apd(tp, false);
-	tg3_phy_toggle_automdix(tp, 0);
+	tg3_phy_toggle_automdix(tp, false);
 
 	if (extlpbk && tg3_phy_set_extloopbk(tp))
 		return -EIO;
@@ -8007,7 +8008,7 @@ static void tg3_set_loopback(struct net_device *dev, netdev_features_t features)
 		spin_lock_bh(&tp->lock);
 		tg3_mac_loopback(tp, false);
 		/* Force link status check */
-		tg3_setup_phy(tp, 1);
+		tg3_setup_phy(tp, true);
 		spin_unlock_bh(&tp->lock);
 		netdev_info(dev, "Internal MAC loopback mode disabled.\n");
 	}
@@ -8518,7 +8519,7 @@ err_out:
 /* To stop a block, clear the enable bit and poll till it
  * clears.  tp->lock is held.
  */
-static int tg3_stop_block(struct tg3 *tp, unsigned long ofs, u32 enable_bit, int silent)
+static int tg3_stop_block(struct tg3 *tp, unsigned long ofs, u32 enable_bit, bool silent)
 {
 	unsigned int i;
 	u32 val;
@@ -8562,7 +8563,7 @@ static int tg3_stop_block(struct tg3 *tp, unsigned long ofs, u32 enable_bit, int
 }
 
 /* tp->lock is held. */
-static int tg3_abort_hw(struct tg3 *tp, int silent)
+static int tg3_abort_hw(struct tg3 *tp, bool silent)
 {
 	int i, err;
 
@@ -8952,7 +8953,7 @@ static void tg3_get_nstats(struct tg3 *, struct rtnl_link_stats64 *);
 static void tg3_get_estats(struct tg3 *, struct tg3_ethtool_stats *);
 
 /* tp->lock is held. */
-static int tg3_halt(struct tg3 *tp, int kind, int silent)
+static int tg3_halt(struct tg3 *tp, int kind, bool silent)
 {
 	int err;
 
@@ -8963,7 +8964,7 @@ static int tg3_halt(struct tg3 *tp, int kind, int silent)
 	tg3_abort_hw(tp, silent);
 	err = tg3_chip_reset(tp);
 
-	__tg3_set_mac_addr(tp, 0);
+	__tg3_set_mac_addr(tp, false);
 
 	tg3_write_sig_legacy(tp, kind);
 	tg3_write_sig_post_reset(tp, kind);
@@ -8987,7 +8988,8 @@ static int tg3_set_mac_addr(struct net_device *dev, void *p)
 {
 	struct tg3 *tp = netdev_priv(dev);
 	struct sockaddr *addr = p;
-	int err = 0, skip_mac_1 = 0;
+	int err = 0;
+	bool skip_mac_1 = false;
 
 	if (!is_valid_ether_addr(addr->sa_data))
 		return -EADDRNOTAVAIL;
@@ -9008,7 +9010,7 @@ static int tg3_set_mac_addr(struct net_device *dev, void *p)
 		/* Skip MAC addr 1 if ASF is using it. */
 		if ((addr0_high != addr1_high || addr0_low != addr1_low) &&
 		    !(addr1_high == 0 && addr1_low == 0))
-			skip_mac_1 = 1;
+			skip_mac_1 = true;
 	}
 	spin_lock_bh(&tp->lock);
 	__tg3_set_mac_addr(tp, skip_mac_1);
@@ -9427,7 +9429,7 @@ static void tg3_rss_write_indir_tbl(struct tg3 *tp)
 }
 
 /* tp->lock is held. */
-static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
+static int tg3_reset_hw(struct tg3 *tp, bool reset_phy)
 {
 	u32 val, rdmac_mode;
 	int i, err, limit;
@@ -9820,7 +9822,7 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 	tg3_rings_reset(tp);
 
 	/* Initialize MAC address and backoff seed. */
-	__tg3_set_mac_addr(tp, 0);
+	__tg3_set_mac_addr(tp, false);
 
 	/* MTU + ethernet header + FCS + optional VLAN tag */
 	tw32(MAC_RX_MTU_SIZE,
@@ -10271,7 +10273,7 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 		if (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)
 			tp->phy_flags &= ~TG3_PHYFLG_IS_LOW_POWER;
 
-		err = tg3_setup_phy(tp, 0);
+		err = tg3_setup_phy(tp, false);
 		if (err)
 			return err;
 
@@ -10351,7 +10353,7 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 /* Called at device open time to get the chip ready for
  * packet processing.  Invoked with tp->lock held.
  */
-static int tg3_init_hw(struct tg3 *tp, int reset_phy)
+static int tg3_init_hw(struct tg3 *tp, bool reset_phy)
 {
 	tg3_switch_clocks(tp);
 
@@ -10612,7 +10614,7 @@ static void tg3_timer(unsigned long __opaque)
 				phy_event = 1;
 
 			if (phy_event)
-				tg3_setup_phy(tp, 0);
+				tg3_setup_phy(tp, false);
 		} else if (tg3_flag(tp, POLL_SERDES)) {
 			u32 mac_stat = tr32(MAC_STATUS);
 			int need_setup = 0;
@@ -10635,7 +10637,7 @@ static void tg3_timer(unsigned long __opaque)
 					tw32_f(MAC_MODE, tp->mac_mode);
 					udelay(40);
 				}
-				tg3_setup_phy(tp, 0);
+				tg3_setup_phy(tp, false);
 			}
 		} else if ((tp->phy_flags & TG3_PHYFLG_MII_SERDES) &&
 			   tg3_flag(tp, 5780_CLASS)) {
@@ -10721,7 +10723,7 @@ static void tg3_timer_stop(struct tg3 *tp)
 /* Restart hardware after configuration changes, self-test, etc.
  * Invoked with tp->lock held.
  */
-static int tg3_restart_hw(struct tg3 *tp, int reset_phy)
+static int tg3_restart_hw(struct tg3 *tp, bool reset_phy)
 	__releases(tp->lock)
 	__acquires(tp->lock)
 {
@@ -10771,7 +10773,7 @@ static void tg3_reset_task(struct work_struct *work)
 	}
 
 	tg3_halt(tp, RESET_KIND_SHUTDOWN, 0);
-	err = tg3_init_hw(tp, 1);
+	err = tg3_init_hw(tp, true);
 	if (err)
 		goto out;
 
@@ -10941,7 +10943,7 @@ static int tg3_test_msi(struct tg3 *tp)
 	tg3_full_lock(tp, 1);
 
 	tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
-	err = tg3_init_hw(tp, 1);
+	err = tg3_init_hw(tp, true);
 
 	tg3_full_unlock(tp);
 
@@ -11814,7 +11816,7 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 	tg3_warn_mgmt_link_flap(tp);
 
 	if (netif_running(dev))
-		tg3_setup_phy(tp, 1);
+		tg3_setup_phy(tp, true);
 
 	tg3_full_unlock(tp);
 
@@ -11970,7 +11972,7 @@ static int tg3_set_ringparam(struct net_device *dev, struct ethtool_ringparam *e
 
 	if (netif_running(dev)) {
 		tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
-		err = tg3_restart_hw(tp, 0);
+		err = tg3_restart_hw(tp, false);
 		if (!err)
 			tg3_netif_start(tp);
 	}
@@ -12094,7 +12096,7 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
 
 		if (netif_running(dev)) {
 			tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
-			err = tg3_restart_hw(tp, 0);
+			err = tg3_restart_hw(tp, false);
 			if (!err)
 				tg3_netif_start(tp);
 		}
@@ -13164,7 +13166,7 @@ static int tg3_test_loopback(struct tg3 *tp, u64 *data, bool do_extlpbk)
 		goto done;
 	}
 
-	err = tg3_reset_hw(tp, 1);
+	err = tg3_reset_hw(tp, true);
 	if (err) {
 		data[TG3_MAC_LOOPB_TEST] = TG3_LOOPBACK_FAILED;
 		data[TG3_PHY_LOOPB_TEST] = TG3_LOOPBACK_FAILED;
@@ -13331,7 +13333,7 @@ static void tg3_self_test(struct net_device *dev, struct ethtool_test *etest,
 		tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
 		if (netif_running(dev)) {
 			tg3_flag_set(tp, INIT_COMPLETE);
-			err2 = tg3_restart_hw(tp, 1);
+			err2 = tg3_restart_hw(tp, true);
 			if (!err2)
 				tg3_netif_start(tp);
 		}
@@ -13648,7 +13650,8 @@ static inline void tg3_set_mtu(struct net_device *dev, struct tg3 *tp,
 static int tg3_change_mtu(struct net_device *dev, int new_mtu)
 {
 	struct tg3 *tp = netdev_priv(dev);
-	int err, reset_phy = 0;
+	int err;
+	bool reset_phy = false;
 
 	if (new_mtu < TG3_MIN_MTU || new_mtu > TG3_MAX_MTU(tp))
 		return -EINVAL;
@@ -13675,7 +13678,7 @@ static int tg3_change_mtu(struct net_device *dev, int new_mtu)
 	 * breaks all requests to 256 bytes.
 	 */
 	if (tg3_asic_rev(tp) == ASIC_REV_57766)
-		reset_phy = 1;
+		reset_phy = true;
 
 	err = tg3_restart_hw(tp, reset_phy);
 
@@ -16575,7 +16578,7 @@ out:
 }
 
 static int tg3_do_test_dma(struct tg3 *tp, u32 *buf, dma_addr_t buf_dma,
-			   int size, int to_device)
+			   int size, bool to_device)
 {
 	struct tg3_internal_buffer_desc test_desc;
 	u32 sram_dma_descs;
@@ -16775,7 +16778,7 @@ static int tg3_test_dma(struct tg3 *tp)
 			p[i] = i;
 
 		/* Send the buffer to the chip. */
-		ret = tg3_do_test_dma(tp, buf, buf_dma, TEST_BUFFER_SIZE, 1);
+		ret = tg3_do_test_dma(tp, buf, buf_dma, TEST_BUFFER_SIZE, true);
 		if (ret) {
 			dev_err(&tp->pdev->dev,
 				"%s: Buffer write failed. err = %d\n",
@@ -16798,7 +16801,7 @@ static int tg3_test_dma(struct tg3 *tp)
 		}
 #endif
 		/* Now read it back. */
-		ret = tg3_do_test_dma(tp, buf, buf_dma, TEST_BUFFER_SIZE, 0);
+		ret = tg3_do_test_dma(tp, buf, buf_dma, TEST_BUFFER_SIZE, false);
 		if (ret) {
 			dev_err(&tp->pdev->dev, "%s: Buffer read failed. "
 				"err = %d\n", __func__, ret);
@@ -17479,7 +17482,7 @@ static int tg3_suspend(struct device *device)
 		tg3_full_lock(tp, 0);
 
 		tg3_flag_set(tp, INIT_COMPLETE);
-		err2 = tg3_restart_hw(tp, 1);
+		err2 = tg3_restart_hw(tp, true);
 		if (err2)
 			goto out;
 
@@ -17653,7 +17656,7 @@ static void tg3_io_resume(struct pci_dev *pdev)
 
 	tg3_full_lock(tp, 0);
 	tg3_flag_set(tp, INIT_COMPLETE);
-	err = tg3_restart_hw(tp, 1);
+	err = tg3_restart_hw(tp, true);
 	if (err) {
 		tg3_full_unlock(tp);
 		netdev_err(netdev, "Cannot restart hardware after reset.\n");

Re: [PATCH net-next 07/11] tg3: Add support for link flap avoidance

[Nithin Nayak Sujir]

On 04/09/2013 12:15 PM, David Miller wrote:
> From: "Nithin Nayak Sujir" <nsujir@broadcom.com>
> Date: Tue, 9 Apr 2013 11:48:07 -0700
>
>> This patch and the following two patches add support for link flap avoidance
>> by maintaining the link on power down. This feature is required for
>> management capable devices to have the management connection
>> uninterrupted on driver reload, reboot and interface up/down.
>>
>> A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
>> support for gigabit link speed when device is on auxiliary power.
>>
>> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
>> Signed-off-by: Michael Chan <mchan@broadcom.com>
>
> Looks good, all applied, thanks.
>
> If we force a PHY reset due to EEE changes, will the ASF traffic
> disruption warning message be emitted?

No, the message is not emitted. There are a couple of reasons for this.

1. The intent of the message is to warn on user initiated operations that cause 
a link flap.

2. The link flap due to EEE mismatch and force reset is possible the very first 
time the system is powered on. It's reasonable to expect the link to be in flux 
till the driver is in sync.


After the 1st time the EEE mismatch can only happen if the user modfies it via 
ethtool. tg3 does not yet support the set_eee ethtool handler. When we implement 
that, we will add the warning there similar to the other ethtool op handlers.


> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>

Re: [PATCH net-next] tg3: Use bool not int

[Michael Chan]

On Tue, 2013-04-09 at 13:18 -0700, Joe Perches wrote:
> Using bool can make code more readable.
> 
> Convert uses and tests of int to bool.
> 
> This also makes a comparison of tg3->link_up
> (itself bool) a bool comparison instead of int.
> 
> Reorder stack variable declarations to make
> bool fit declaration holes where appropriate.
> 
> $ size drivers/net/ethernet/broadcom/tg3.o*
>    text    data     bss     dec     hex filename
>  169958   27249   58896  256103   3e867 drivers/net/ethernet/broadcom/tg3.o.new
>  169968   27249   58896  256113   3e871 drivers/net/ethernet/broadcom/tg3.o.old
> 
> Signed-off-by: Joe Perches <joe@perches.com> 

Thanks.

Reviewed-by: Michael Chan <mchan@broadcom.com>

Re: [PATCH net-next 07/11] tg3: Add support for link flap avoidance

[David Miller]

From: "Nithin Nayak Sujir" <nsujir@broadcom.com>
Date: Tue, 9 Apr 2013 13:59:08 -0700

> On 04/09/2013 12:15 PM, David Miller wrote:
>> From: "Nithin Nayak Sujir" <nsujir@broadcom.com>
>> Date: Tue, 9 Apr 2013 11:48:07 -0700
>>
>> If we force a PHY reset due to EEE changes, will the ASF traffic
>> disruption warning message be emitted?
> 
> No, the message is not emitted. There are a couple of reasons for
> this.
> 
> 1. The intent of the message is to warn on user initiated operations
> that cause a link flap.
> 
> 2. The link flap due to EEE mismatch and force reset is possible the
> very first time the system is powered on. It's reasonable to expect
> the link to be in flux till the driver is in sync.
> 
> After the 1st time the EEE mismatch can only happen if the user
> modfies it via ethtool. tg3 does not yet support the set_eee ethtool
> handler. When we implement that, we will add the warning there similar
> to the other ethtool op handlers.

Ok, thanks for the explanation.

Re: [PATCH net-next] tg3: Use bool not int

[David Miller]

From: "Michael Chan" <mchan@broadcom.com>
Date: Tue, 9 Apr 2013 14:00:11 -0700

> On Tue, 2013-04-09 at 13:18 -0700, Joe Perches wrote:
>> Using bool can make code more readable.
>> 
>> Convert uses and tests of int to bool.
>> 
>> This also makes a comparison of tg3->link_up
>> (itself bool) a bool comparison instead of int.
>> 
>> Reorder stack variable declarations to make
>> bool fit declaration holes where appropriate.
>> 
>> $ size drivers/net/ethernet/broadcom/tg3.o*
>>    text    data     bss     dec     hex filename
>>  169958   27249   58896  256103   3e867 drivers/net/ethernet/broadcom/tg3.o.new
>>  169968   27249   58896  256113   3e871 drivers/net/ethernet/broadcom/tg3.o.old
>> 
>> Signed-off-by: Joe Perches <joe@perches.com> 
> 
> Thanks.
> 
> Reviewed-by: Michael Chan <mchan@broadcom.com>

Applied.

Re: [PATCH net-next 04/11] tg3: Add a warning during link settings change if mgmt enabled

[Ben Hutchings]

On Tue, 2013-04-09 at 11:48 -0700, Nithin Nayak Sujir wrote:
> When the user executes certain ethtool commands such as -s, -A, -G, -L,
> -r a phy reset or autonegotiate is performed which results in management
> traffic being interrupted.
> 
> Add a warning in these cases.

It seems entirely obvious that PHY reconfiguration will break the link
and stop all traffic until the link is re-established; this is nothing
specific to this driver.  Is it more disruptive to management traffic on
these controllers?  Unless it is, I think this is not a helpful warning.

Ben.

> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
> Signed-off-by: Michael Chan <mchan@broadcom.com>
> ---
>  drivers/net/ethernet/broadcom/tg3.c | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
> 
> diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
> index 3f0d43f..a744998 100644
> --- a/drivers/net/ethernet/broadcom/tg3.c
> +++ b/drivers/net/ethernet/broadcom/tg3.c
> @@ -2531,6 +2531,13 @@ static void tg3_carrier_off(struct tg3 *tp)
>  	tp->link_up = false;
>  }
>  
> +static void tg3_warn_mgmt_link_flap(struct tg3 *tp)
> +{
> +	if (tg3_flag(tp, ENABLE_ASF))
> +		netdev_warn(tp->dev,
> +			    "Management side-band traffic will be interrupted during phy settings change\n");
> +}
> +
>  /* This will reset the tigon3 PHY if there is no valid
>   * link unless the FORCE argument is non-zero.
>   */
> @@ -11565,6 +11572,8 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
>  		tp->link_config.duplex = cmd->duplex;
>  	}
>  
> +	tg3_warn_mgmt_link_flap(tp);
> +
>  	if (netif_running(dev))
>  		tg3_setup_phy(tp, 1);
>  
> @@ -11643,6 +11652,8 @@ static int tg3_nway_reset(struct net_device *dev)
>  	if (tp->phy_flags & TG3_PHYFLG_PHY_SERDES)
>  		return -EINVAL;
>  
> +	tg3_warn_mgmt_link_flap(tp);
> +
>  	if (tg3_flag(tp, USE_PHYLIB)) {
>  		if (!(tp->phy_flags & TG3_PHYFLG_IS_CONNECTED))
>  			return -EAGAIN;
> @@ -11755,6 +11766,9 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
>  	struct tg3 *tp = netdev_priv(dev);
>  	int err = 0;
>  
> +	if (tp->link_config.autoneg == AUTONEG_ENABLE)
> +		tg3_warn_mgmt_link_flap(tp);
> +
>  	if (tg3_flag(tp, USE_PHYLIB)) {
>  		u32 newadv;
>  		struct phy_device *phydev;

-- 
Ben Hutchings, Staff Engineer, Solarflare
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.

Re: [PATCH net-next 04/11] tg3: Add a warning during link settings change if mgmt enabled

[Nithin Nayak Sujir]

On 4/10/2013 5:56 AM, Ben Hutchings wrote:
> On Tue, 2013-04-09 at 11:48 -0700, Nithin Nayak Sujir wrote:
>> When the user executes certain ethtool commands such as -s, -A, -G, -L,
>> -r a phy reset or autonegotiate is performed which results in management
>> traffic being interrupted.
>>
>> Add a warning in these cases.
>
> It seems entirely obvious that PHY reconfiguration will break the link
> and stop all traffic until the link is re-established; this is nothing
> specific to this driver.  Is it more disruptive to management traffic on
> these controllers?  Unless it is, I think this is not a helpful warning.

This goes in conjunction with the Link Flap Avoidance feature introduced 
in this patchset. For the LFA feature the driver skips the normal phy 
resets and speed changes to maintain the link. The expectation now is 
that mgmt traffic is never interrupted even if the interface is brought 
down or the system rebooted/suspended etc.

Except, in these cases where the user forces a phy change we don't 
prevent it. We let the user go ahead with the config change but it does 
flap the link. It's useful to have this event logged to let the user 
know the flap was intentional.

To simplify the conditional, we don't limit it to only LFA enabled 
devices since it doesn't hurt to have it.


>
> Ben.
>
>> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
>> Signed-off-by: Michael Chan <mchan@broadcom.com>
>> ---
>>   drivers/net/ethernet/broadcom/tg3.c | 14 ++++++++++++++
>>   1 file changed, 14 insertions(+)
>>
>> diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
>> index 3f0d43f..a744998 100644
>> --- a/drivers/net/ethernet/broadcom/tg3.c
>> +++ b/drivers/net/ethernet/broadcom/tg3.c
>> @@ -2531,6 +2531,13 @@ static void tg3_carrier_off(struct tg3 *tp)
>>   	tp->link_up = false;
>>   }
>>
>> +static void tg3_warn_mgmt_link_flap(struct tg3 *tp)
>> +{
>> +	if (tg3_flag(tp, ENABLE_ASF))
>> +		netdev_warn(tp->dev,
>> +			    "Management side-band traffic will be interrupted during phy settings change\n");
>> +}
>> +
>>   /* This will reset the tigon3 PHY if there is no valid
>>    * link unless the FORCE argument is non-zero.
>>    */
>> @@ -11565,6 +11572,8 @@ static int tg3_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
>>   		tp->link_config.duplex = cmd->duplex;
>>   	}
>>
>> +	tg3_warn_mgmt_link_flap(tp);
>> +
>>   	if (netif_running(dev))
>>   		tg3_setup_phy(tp, 1);
>>
>> @@ -11643,6 +11652,8 @@ static int tg3_nway_reset(struct net_device *dev)
>>   	if (tp->phy_flags & TG3_PHYFLG_PHY_SERDES)
>>   		return -EINVAL;
>>
>> +	tg3_warn_mgmt_link_flap(tp);
>> +
>>   	if (tg3_flag(tp, USE_PHYLIB)) {
>>   		if (!(tp->phy_flags & TG3_PHYFLG_IS_CONNECTED))
>>   			return -EAGAIN;
>> @@ -11755,6 +11766,9 @@ static int tg3_set_pauseparam(struct net_device *dev, struct ethtool_pauseparam
>>   	struct tg3 *tp = netdev_priv(dev);
>>   	int err = 0;
>>
>> +	if (tp->link_config.autoneg == AUTONEG_ENABLE)
>> +		tg3_warn_mgmt_link_flap(tp);
>> +
>>   	if (tg3_flag(tp, USE_PHYLIB)) {
>>   		u32 newadv;
>>   		struct phy_device *phydev;
>