[PATCH 0/2] USB: OHCI: more bus glues as separate modules

[PATCH 0/2] USB: OHCI: more bus glues as separate modules

[Manjunath Goudar]

These patches are for separating the SOC On-Chip ohci host controller
from ohci-hcd host code into its own driver module.
This work is part of enabling multi-platform kernels on ARM.

Manjunath Goudar (2):
  USB: OHCI: make ohci-ep93xx a separate driver
  USB: OHCI: make ohci-pxa27x a separate driver

 drivers/usb/host/Kconfig       |   16 +++++
 drivers/usb/host/Makefile      |    2 +
 drivers/usb/host/ohci-ep93xx.c |   84 ++++++++++------------
 drivers/usb/host/ohci-hcd.c    |   24 -------
 drivers/usb/host/ohci-pxa27x.c |  154 ++++++++++++++++------------------------
 5 files changed, 120 insertions(+), 160 deletions(-)

-- 
1.7.9.5

[PATCH 1/2] USB: OHCI: make ohci-ep93xx a separate driver

[Manjunath Goudar]

Separate the OHCI EP93XX host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.

Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: linux-usb at vger.kernel.org
---
 drivers/usb/host/Kconfig       |    8 ++++
 drivers/usb/host/Makefile      |    1 +
 drivers/usb/host/ohci-ep93xx.c |   84 +++++++++++++++++++---------------------
 drivers/usb/host/ohci-hcd.c    |   19 ---------
 4 files changed, 48 insertions(+), 64 deletions(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index bf9a162..35c7001 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -414,6 +414,14 @@ config USB_OHCI_HCD_DA8XX
           Enables support for the on-chip OHCI controller on
           DA8xx/OMAP-L1x chips.
 
+config USB_OHCI_HCD_EP93XX
+	tristate "Support for EP93XX on-chip OHCI USB controller"
+	depends on USB_OHCI_HCD && ARCH_EP93XX
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  EP93XX chips.
+
 config USB_OHCI_HCD_AT91
         tristate  "Support for Atmel on-chip OHCI USB controller"
         depends on USB_OHCI_HCD && ARCH_AT91
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index f8d59371..3fee3ea 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_USB_OHCI_HCD_AT91)	+= ohci-at91.o
 obj-$(CONFIG_USB_OHCI_HCD_S3CXXXX)	+= ohci-s3c2410.o
 obj-$(CONFIG_USB_OHCI_HCD_LPC32XX)	+= ohci-nxp.o
 obj-$(CONFIG_USB_OHCI_HCD_DA8XX)	+= ohci-da8xx.o
+obj-$(CONFIG_USB_OHCI_HCD_EP93XX)	+= ohci-ep93xx.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
diff --git a/drivers/usb/host/ohci-ep93xx.c b/drivers/usb/host/ohci-ep93xx.c
index f0aaa48..0c2f6df 100644
--- a/drivers/usb/host/ohci-ep93xx.c
+++ b/drivers/usb/host/ohci-ep93xx.c
@@ -25,8 +25,21 @@
 
 #include <linux/clk.h>
 #include <linux/device.h>
-#include <linux/signal.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI EP93xx driver"
+
+static const char hcd_name[] = "ohci-ep93xx";
+
+static struct hc_driver __read_mostly ohci_ep93xx_hc_driver;
 
 static struct clk *usb_host_clock;
 
@@ -45,6 +58,7 @@ static int usb_hcd_ep93xx_probe(const struct hc_driver *driver,
 {
 	int retval;
 	struct usb_hcd *hcd;
+	struct ohci_hcd *ohci;
 
 	if (pdev->resource[1].flags != IORESOURCE_IRQ) {
 		dev_dbg(&pdev->dev, "resource[1] is not IORESOURCE_IRQ\n");
@@ -79,7 +93,10 @@ static int usb_hcd_ep93xx_probe(const struct hc_driver *driver,
 
 	ep93xx_start_hc(&pdev->dev);
 
-	ohci_hcd_init(hcd_to_ohci(hcd));
+	ohci = hcd_to_ohci(hcd);
+	ohci->next_statechange = jiffies;
+	spin_lock_init(&ohci->lock);
+	INIT_LIST_HEAD(&ohci->pending);
 
 	retval = usb_add_hcd(hcd, pdev->resource[1].start, 0);
 	if (retval == 0)
@@ -107,48 +124,6 @@ static void usb_hcd_ep93xx_remove(struct usb_hcd *hcd,
 	usb_put_hcd(hcd);
 }
 
-static int ohci_ep93xx_start(struct usb_hcd *hcd)
-{
-	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
-	int ret;
-
-	if ((ret = ohci_init(ohci)) < 0)
-		return ret;
-
-	if ((ret = ohci_run(ohci)) < 0) {
-		dev_err(hcd->self.controller, "can't start %s\n",
-			hcd->self.bus_name);
-		ohci_stop(hcd);
-		return ret;
-	}
-
-	return 0;
-}
-
-static struct hc_driver ohci_ep93xx_hc_driver = {
-	.description		= hcd_name,
-	.product_desc		= "EP93xx OHCI",
-	.hcd_priv_size		= sizeof(struct ohci_hcd),
-	.irq			= ohci_irq,
-	.flags			= HCD_USB11 | HCD_MEMORY,
-	.start			= ohci_ep93xx_start,
-	.stop			= ohci_stop,
-	.shutdown		= ohci_shutdown,
-	.urb_enqueue		= ohci_urb_enqueue,
-	.urb_dequeue		= ohci_urb_dequeue,
-	.endpoint_disable	= ohci_endpoint_disable,
-	.get_frame_number	= ohci_get_frame,
-	.hub_status_data	= ohci_hub_status_data,
-	.hub_control		= ohci_hub_control,
-#ifdef CONFIG_PM
-	.bus_suspend		= ohci_bus_suspend,
-	.bus_resume		= ohci_bus_resume,
-#endif
-	.start_port_reset	= ohci_start_port_reset,
-};
-
-extern int usb_disabled(void);
-
 static int ohci_hcd_ep93xx_drv_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -206,7 +181,6 @@ static int ohci_hcd_ep93xx_drv_resume(struct platform_device *pdev)
 }
 #endif
 
-
 static struct platform_driver ohci_hcd_ep93xx_driver = {
 	.probe		= ohci_hcd_ep93xx_drv_probe,
 	.remove		= ohci_hcd_ep93xx_drv_remove,
@@ -221,4 +195,24 @@ static struct platform_driver ohci_hcd_ep93xx_driver = {
 	},
 };
 
+static int __init ohci_ep93xx_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+
+	ohci_init_driver(&ohci_ep93xx_hc_driver, NULL);
+	return platform_driver_register(&ohci_hcd_ep93xx_driver);
+}
+module_init(ohci_ep93xx_init);
+
+static void __exit ohci_ep93xx_cleanup(void)
+{
+	platform_driver_unregister(&ohci_hcd_ep93xx_driver);
+}
+module_exit(ohci_ep93xx_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:ep93xx-ohci");
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index d514e11..3f46cff 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1189,11 +1189,6 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ohci_hcd_pxa27x_driver
 #endif
 
-#ifdef CONFIG_ARCH_EP93XX
-#include "ohci-ep93xx.c"
-#define EP93XX_PLATFORM_DRIVER	ohci_hcd_ep93xx_driver
-#endif
-
 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 #include "ohci-ppc-of.c"
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
@@ -1284,20 +1279,9 @@ static int __init ohci_hcd_mod_init(void)
 	if (retval < 0)
 		goto error_tmio;
 #endif
-
-#ifdef EP93XX_PLATFORM_DRIVER
-	retval = platform_driver_register(&EP93XX_PLATFORM_DRIVER);
-	if (retval < 0)
-		goto error_ep93xx;
-#endif
-
 	return retval;
 
 	/* Error path */
-#ifdef EP93XX_PLATFORM_DRIVER
-	platform_driver_unregister(&EP93XX_PLATFORM_DRIVER);
- error_ep93xx:
-#endif
 #ifdef TMIO_OHCI_DRIVER
 	platform_driver_unregister(&TMIO_OHCI_DRIVER);
  error_tmio:
@@ -1335,9 +1319,6 @@ module_init(ohci_hcd_mod_init);
 
 static void __exit ohci_hcd_mod_exit(void)
 {
-#ifdef EP93XX_PLATFORM_DRIVER
-	platform_driver_unregister(&EP93XX_PLATFORM_DRIVER);
-#endif
 #ifdef TMIO_OHCI_DRIVER
 	platform_driver_unregister(&TMIO_OHCI_DRIVER);
 #endif
-- 
1.7.9.5

[PATCH 2/2] USB: OHCI: make ohci-pxa27x a separate driver

[Manjunath Goudar]

Separate the  OHCI pxa27x/pxa3xx host controller driver from
ohci-hcd host code so that it can be built as a separate driver
module. This work is part of enabling multi-platform kernels on
ARM.

Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb at vger.kernel.org
---
 drivers/usb/host/Kconfig       |    8 +++
 drivers/usb/host/Makefile      |    1 +
 drivers/usb/host/ohci-hcd.c    |    5 --
 drivers/usb/host/ohci-pxa27x.c |  154 ++++++++++++++++------------------------
 4 files changed, 72 insertions(+), 96 deletions(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 35c7001..f6fefa2 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -422,6 +422,14 @@ config USB_OHCI_HCD_EP93XX
 	  Enables support for the on-chip OHCI controller on
 	  EP93XX chips.
 
+config USB_OHCI_HCD_PXA27X
+	tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
+	depends on USB_OHCI_HCD && ARCH_PXA
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  PXA27X/PXA3XX chips.
+
 config USB_OHCI_HCD_AT91
         tristate  "Support for Atmel on-chip OHCI USB controller"
         depends on USB_OHCI_HCD && ARCH_AT91
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 3fee3ea..8b7fa89 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_OHCI_HCD_S3CXXXX)	+= ohci-s3c2410.o
 obj-$(CONFIG_USB_OHCI_HCD_LPC32XX)	+= ohci-nxp.o
 obj-$(CONFIG_USB_OHCI_HCD_DA8XX)	+= ohci-da8xx.o
 obj-$(CONFIG_USB_OHCI_HCD_EP93XX)	+= ohci-ep93xx.o
+obj-$(CONFIG_USB_OHCI_HCD_PXA27X)	+= ohci-pxa27x.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 3f46cff..f601dde 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1184,11 +1184,6 @@ MODULE_LICENSE ("GPL");
 #define SA1111_DRIVER		ohci_hcd_sa1111_driver
 #endif
 
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#include "ohci-pxa27x.c"
-#define PLATFORM_DRIVER		ohci_hcd_pxa27x_driver
-#endif
-
 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 #include "ohci-ppc-of.c"
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 5fb91f1..791e2b5 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -19,15 +19,26 @@
  * This file is licenced under the GPL.
  */
 
-#include <linux/device.h>
-#include <linux/signal.h>
-#include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
-#include <mach/hardware.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
+#include <linux/platform_device.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+#include <linux/usb/otg.h>
+
+#include <mach/hardware.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI PXA27X driver"
 
 /*
  * UHC: USB Host Controller (OHCI-like) register definitions
@@ -101,11 +112,11 @@
 
 #define PXA_UHC_MAX_PORTNUM    3
 
-struct pxa27x_ohci {
-	/* must be 1st member here for hcd_to_ohci() to work */
-	struct ohci_hcd ohci;
+static const char hcd_name[] = "ohci-pxa27x";
 
-	struct device	*dev;
+static struct hc_driver __read_mostly ohci_pxa27x_hc_driver;
+
+struct pxa27x_ohci {
 	struct clk	*clk;
 	void __iomem	*mmio_base;
 };
@@ -154,8 +165,6 @@ static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
 	return 0;
 }
 
-extern int usb_disabled(void);
-
 /*-------------------------------------------------------------------------*/
 
 static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
@@ -218,6 +227,7 @@ static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 	int retval = 0;
 	struct pxaohci_platform_data *inf;
 	uint32_t uhchr;
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	inf = dev->platform_data;
 
@@ -240,7 +250,7 @@ static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 		return retval;
 
 	if (cpu_is_pxa3xx())
-		pxa3xx_u2d_start_hc(&ohci_to_hcd(&ohci->ohci)->self);
+		pxa3xx_u2d_start_hc(&hcd->self);
 
 	uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
 	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
@@ -254,12 +264,13 @@ static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 static void pxa27x_stop_hc(struct pxa27x_ohci *ohci, struct device *dev)
 {
 	struct pxaohci_platform_data *inf;
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	uint32_t uhccoms;
 
 	inf = dev->platform_data;
 
 	if (cpu_is_pxa3xx())
-		pxa3xx_u2d_stop_hc(&ohci_to_hcd(&ohci->ohci)->self);
+		pxa3xx_u2d_stop_hc(&hcd->self);
 
 	if (inf->exit)
 		inf->exit(dev);
@@ -357,6 +368,7 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	struct usb_hcd *hcd;
 	struct pxaohci_platform_data *inf;
 	struct pxa27x_ohci *ohci;
+	struct ohci_hcd *pxaohci;
 	struct resource *r;
 	struct clk *usb_clk;
 
@@ -410,7 +422,6 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 
 	/* initialize "struct pxa27x_ohci" */
 	ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd);
-	ohci->dev = &pdev->dev;
 	ohci->clk = usb_clk;
 	ohci->mmio_base = (void __iomem *)hcd->regs;
 
@@ -425,7 +436,13 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	if (inf->power_budget)
 		hcd->power_budget = inf->power_budget;
 
-	ohci_hcd_init(hcd_to_ohci(hcd));
+	pxaohci = hcd_to_ohci(hcd);
+	pxaohci->next_statechange = jiffies;
+	spin_lock_init(&pxaohci->lock);
+	INIT_LIST_HEAD(&pxaohci->pending);
+
+	 /* The value of NDP in roothub_a is incorrect on this hardware */
+	pxaohci->num_ports = 3;
 
 	retval = usb_add_hcd(hcd, irq, 0);
 	if (retval == 0)
@@ -471,76 +488,6 @@ void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 
 /*-------------------------------------------------------------------------*/
 
-static int
-ohci_pxa27x_start (struct usb_hcd *hcd)
-{
-	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
-	int		ret;
-
-	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);
-
-	/* The value of NDP in roothub_a is incorrect on this hardware */
-	ohci->num_ports = 3;
-
-	if ((ret = ohci_init(ohci)) < 0)
-		return ret;
-
-	if ((ret = ohci_run (ohci)) < 0) {
-		dev_err(hcd->self.controller, "can't start %s",
-			hcd->self.bus_name);
-		ohci_stop (hcd);
-		return ret;
-	}
-
-	return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-static const struct hc_driver ohci_pxa27x_hc_driver = {
-	.description =		hcd_name,
-	.product_desc =		"PXA27x OHCI",
-	.hcd_priv_size =	sizeof(struct pxa27x_ohci),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq =			ohci_irq,
-	.flags =		HCD_USB11 | HCD_MEMORY,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.start =		ohci_pxa27x_start,
-	.stop =			ohci_stop,
-	.shutdown =		ohci_shutdown,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue =		ohci_urb_enqueue,
-	.urb_dequeue =		ohci_urb_dequeue,
-	.endpoint_disable =	ohci_endpoint_disable,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number =	ohci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data =	ohci_hub_status_data,
-	.hub_control =		ohci_hub_control,
-#ifdef  CONFIG_PM
-	.bus_suspend =		ohci_bus_suspend,
-	.bus_resume =		ohci_bus_resume,
-#endif
-	.start_port_reset =	ohci_start_port_reset,
-};
-
-/*-------------------------------------------------------------------------*/
-
 static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
 {
 	pr_debug ("In ohci_hcd_pxa27x_drv_probe");
@@ -565,11 +512,13 @@ static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
 	bool do_wakeup = device_may_wakeup(dev);
+	struct ohci_hcd *pxaohci = hcd_to_ohci(hcd);
 	int ret;
 
-	if (time_before(jiffies, ohci->ohci.next_statechange))
+	if (time_before(jiffies, pxaohci->next_statechange))
 		msleep(5);
-	ohci->ohci.next_statechange = jiffies;
+
+	pxaohci->next_statechange = jiffies;
 
 	ret = ohci_suspend(hcd, do_wakeup);
 	if (ret)
@@ -584,11 +533,13 @@ static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
 	struct pxaohci_platform_data *inf = dev->platform_data;
+	struct ohci_hcd *pxaohci = hcd_to_ohci(hcd);
 	int status;
 
-	if (time_before(jiffies, ohci->ohci.next_statechange))
+	if (time_before(jiffies, pxaohci->next_statechange))
 		msleep(5);
-	ohci->ohci.next_statechange = jiffies;
+
+	pxaohci->next_statechange = jiffies;
 
 	if ((status = pxa27x_start_hc(ohci, dev)) < 0)
 		return status;
@@ -606,9 +557,6 @@ static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
 };
 #endif
 
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:pxa27x-ohci");
-
 static struct platform_driver ohci_hcd_pxa27x_driver = {
 	.probe		= ohci_hcd_pxa27x_drv_probe,
 	.remove		= ohci_hcd_pxa27x_drv_remove,
@@ -623,3 +571,27 @@ static struct platform_driver ohci_hcd_pxa27x_driver = {
 	},
 };
 
+static const struct ohci_driver_overrides pxa27x_overrides __initconst = {
+	.extra_priv_size =      sizeof(struct pxa27x_ohci),
+};
+
+static int __init ohci_pxa27x_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+	ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides);
+	return platform_driver_register(&ohci_hcd_pxa27x_driver);
+}
+module_init(ohci_pxa27x_init);
+
+static void __exit ohci_pxa27x_cleanup(void)
+{
+	platform_driver_unregister(&ohci_hcd_pxa27x_driver);
+}
+module_exit(ohci_pxa27x_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pxa27x-ohci");
-- 
1.7.9.5

[PATCH 1/2] USB: OHCI: make ohci-ep93xx a separate driver

[Alan Stern]

On Thu, 4 Jul 2013, Manjunath Goudar wrote:

> Separate the OHCI EP93XX host controller driver from ohci-hcd
> host code so that it can be built as a separate driver module.
> This work is part of enabling multi-platform kernels on ARM.

> @@ -79,7 +93,10 @@ static int usb_hcd_ep93xx_probe(const struct hc_driver *driver,
>  
>  	ep93xx_start_hc(&pdev->dev);
>  
> -	ohci_hcd_init(hcd_to_ohci(hcd));
> +	ohci = hcd_to_ohci(hcd);
> +	ohci->next_statechange = jiffies;
> +	spin_lock_init(&ohci->lock);
> +	INIT_LIST_HEAD(&ohci->pending);
>  
>  	retval = usb_add_hcd(hcd, pdev->resource[1].start, 0);
>  	if (retval == 0)

Why did you add these lines?

Alan Stern

[PATCH 2/2] USB: OHCI: make ohci-pxa27x a separate driver

[Alan Stern]

On Thu, 4 Jul 2013, Manjunath Goudar wrote:

> Separate the  OHCI pxa27x/pxa3xx host controller driver from
> ohci-hcd host code so that it can be built as a separate driver
> module. This work is part of enabling multi-platform kernels on
> ARM.

> +config USB_OHCI_HCD_PXA27X
> +	tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
> +	depends on USB_OHCI_HCD && ARCH_PXA

Shouldn't the ARCH_PXA part be the same as ...

> @@ -1184,11 +1184,6 @@ MODULE_LICENSE ("GPL");
>  #define SA1111_DRIVER		ohci_hcd_sa1111_driver
>  #endif
>  
> -#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)

... this?

> diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
> index 5fb91f1..791e2b5 100644
> --- a/drivers/usb/host/ohci-pxa27x.c
> +++ b/drivers/usb/host/ohci-pxa27x.c

Several aspects of this are strange.  For example, consider how you 
used the private part of the ohci_hcd structure and how the variable 
names are inconsistent with the other OHCI glue drivers.

Alan Stern

[PATCH V3 0/2] USB: OHCI: more bus glues as separate modules

[Manjunath Goudar]

These patches are for separating the SOC On-Chip ohci host controller
from ohci-hcd host code into its own driver module.
This work is part of enabling multi-platform kernels on ARM.

In V2:

patch 1/2:
     -ohci_hcd_init() statements are removed,
      because by default it is called in ohci_setup().

Patch 2/2:
     -Changed ohci_hcd and pxa27x_ohci struct variable names.
        1 ohci_hcd struct variable name is ohci.
        2 pxa27x_ohci struct variable name is pxa_ohci.
 
In V3:

Patch 1/2:
     -Unused *ohci variable has been removed.

patch 2/2:
     -Rewrite the macro definition of to_pxa27x_ohci.
     -clk_put() function has been called before usb_put_hcd().

Manjunath Goudar (2):
  USB: OHCI: make ohci-ep93xx a separate driver
  USB: OHCI: make ohci-pxa27x a separate driver

 drivers/usb/host/Kconfig       |   16 +++
 drivers/usb/host/Makefile      |    2 +
 drivers/usb/host/ohci-ep93xx.c |   80 ++++++-------
 drivers/usb/host/ohci-hcd.c    |   24 ----
 drivers/usb/host/ohci-pxa27x.c |  242 ++++++++++++++++++----------------------
 5 files changed, 158 insertions(+), 206 deletions(-)

-- 
1.7.9.5

[PATCH V3 1/2] USB: OHCI: make ohci-ep93xx a separate driver

[Manjunath Goudar]

Separate the OHCI EP93XX host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.

Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: linux-usb at vger.kernel.org

V2:
 -ohci_hcd_init() statements are removed,
  because by default it is called in ohci_setup().

V3:
 -Unused *ohci variable has been removed.
---
 drivers/usb/host/Kconfig       |    8 ++++
 drivers/usb/host/Makefile      |    1 +
 drivers/usb/host/ohci-ep93xx.c |   80 +++++++++++++++++-----------------------
 drivers/usb/host/ohci-hcd.c    |   19 ----------
 4 files changed, 43 insertions(+), 65 deletions(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index f7f7823..cdfaa04 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -414,6 +414,14 @@ config USB_OHCI_HCD_DA8XX
           Enables support for the on-chip OHCI controller on
           DA8xx/OMAP-L1x chips.
 
+config USB_OHCI_HCD_EP93XX
+	tristate "Support for EP93XX on-chip OHCI USB controller"
+	depends on USB_OHCI_HCD && ARCH_EP93XX
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  EP93XX chips.
+
 config USB_OHCI_HCD_AT91
         tristate "Support for Atmel on-chip OHCI USB controller"
         depends on USB_OHCI_HCD && ARCH_AT91
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index f8d59371..3fee3ea 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_USB_OHCI_HCD_AT91)	+= ohci-at91.o
 obj-$(CONFIG_USB_OHCI_HCD_S3CXXXX)	+= ohci-s3c2410.o
 obj-$(CONFIG_USB_OHCI_HCD_LPC32XX)	+= ohci-nxp.o
 obj-$(CONFIG_USB_OHCI_HCD_DA8XX)	+= ohci-da8xx.o
+obj-$(CONFIG_USB_OHCI_HCD_EP93XX)	+= ohci-ep93xx.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
diff --git a/drivers/usb/host/ohci-ep93xx.c b/drivers/usb/host/ohci-ep93xx.c
index f0aaa48..7b0e3ae 100644
--- a/drivers/usb/host/ohci-ep93xx.c
+++ b/drivers/usb/host/ohci-ep93xx.c
@@ -25,8 +25,21 @@
 
 #include <linux/clk.h>
 #include <linux/device.h>
-#include <linux/signal.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI EP93xx driver"
+
+static const char hcd_name[] = "ohci-ep93xx";
+
+static struct hc_driver __read_mostly ohci_ep93xx_hc_driver;
 
 static struct clk *usb_host_clock;
 
@@ -79,8 +92,6 @@ static int usb_hcd_ep93xx_probe(const struct hc_driver *driver,
 
 	ep93xx_start_hc(&pdev->dev);
 
-	ohci_hcd_init(hcd_to_ohci(hcd));
-
 	retval = usb_add_hcd(hcd, pdev->resource[1].start, 0);
 	if (retval == 0)
 		return retval;
@@ -107,48 +118,6 @@ static void usb_hcd_ep93xx_remove(struct usb_hcd *hcd,
 	usb_put_hcd(hcd);
 }
 
-static int ohci_ep93xx_start(struct usb_hcd *hcd)
-{
-	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
-	int ret;
-
-	if ((ret = ohci_init(ohci)) < 0)
-		return ret;
-
-	if ((ret = ohci_run(ohci)) < 0) {
-		dev_err(hcd->self.controller, "can't start %s\n",
-			hcd->self.bus_name);
-		ohci_stop(hcd);
-		return ret;
-	}
-
-	return 0;
-}
-
-static struct hc_driver ohci_ep93xx_hc_driver = {
-	.description		= hcd_name,
-	.product_desc		= "EP93xx OHCI",
-	.hcd_priv_size		= sizeof(struct ohci_hcd),
-	.irq			= ohci_irq,
-	.flags			= HCD_USB11 | HCD_MEMORY,
-	.start			= ohci_ep93xx_start,
-	.stop			= ohci_stop,
-	.shutdown		= ohci_shutdown,
-	.urb_enqueue		= ohci_urb_enqueue,
-	.urb_dequeue		= ohci_urb_dequeue,
-	.endpoint_disable	= ohci_endpoint_disable,
-	.get_frame_number	= ohci_get_frame,
-	.hub_status_data	= ohci_hub_status_data,
-	.hub_control		= ohci_hub_control,
-#ifdef CONFIG_PM
-	.bus_suspend		= ohci_bus_suspend,
-	.bus_resume		= ohci_bus_resume,
-#endif
-	.start_port_reset	= ohci_start_port_reset,
-};
-
-extern int usb_disabled(void);
-
 static int ohci_hcd_ep93xx_drv_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -206,7 +175,6 @@ static int ohci_hcd_ep93xx_drv_resume(struct platform_device *pdev)
 }
 #endif
 
-
 static struct platform_driver ohci_hcd_ep93xx_driver = {
 	.probe		= ohci_hcd_ep93xx_drv_probe,
 	.remove		= ohci_hcd_ep93xx_drv_remove,
@@ -221,4 +189,24 @@ static struct platform_driver ohci_hcd_ep93xx_driver = {
 	},
 };
 
+static int __init ohci_ep93xx_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+
+	ohci_init_driver(&ohci_ep93xx_hc_driver, NULL);
+	return platform_driver_register(&ohci_hcd_ep93xx_driver);
+}
+module_init(ohci_ep93xx_init);
+
+static void __exit ohci_ep93xx_cleanup(void)
+{
+	platform_driver_unregister(&ohci_hcd_ep93xx_driver);
+}
+module_exit(ohci_ep93xx_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:ep93xx-ohci");
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index d514e11..3f46cff 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1189,11 +1189,6 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ohci_hcd_pxa27x_driver
 #endif
 
-#ifdef CONFIG_ARCH_EP93XX
-#include "ohci-ep93xx.c"
-#define EP93XX_PLATFORM_DRIVER	ohci_hcd_ep93xx_driver
-#endif
-
 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 #include "ohci-ppc-of.c"
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
@@ -1284,20 +1279,9 @@ static int __init ohci_hcd_mod_init(void)
 	if (retval < 0)
 		goto error_tmio;
 #endif
-
-#ifdef EP93XX_PLATFORM_DRIVER
-	retval = platform_driver_register(&EP93XX_PLATFORM_DRIVER);
-	if (retval < 0)
-		goto error_ep93xx;
-#endif
-
 	return retval;
 
 	/* Error path */
-#ifdef EP93XX_PLATFORM_DRIVER
-	platform_driver_unregister(&EP93XX_PLATFORM_DRIVER);
- error_ep93xx:
-#endif
 #ifdef TMIO_OHCI_DRIVER
 	platform_driver_unregister(&TMIO_OHCI_DRIVER);
  error_tmio:
@@ -1335,9 +1319,6 @@ module_init(ohci_hcd_mod_init);
 
 static void __exit ohci_hcd_mod_exit(void)
 {
-#ifdef EP93XX_PLATFORM_DRIVER
-	platform_driver_unregister(&EP93XX_PLATFORM_DRIVER);
-#endif
 #ifdef TMIO_OHCI_DRIVER
 	platform_driver_unregister(&TMIO_OHCI_DRIVER);
 #endif
-- 
1.7.9.5

[PATCH V3 2/2] USB: OHCI: make ohci-pxa27x a separate driver

[Manjunath Goudar]

Separate the  OHCI pxa27x/pxa3xx host controller driver from
ohci-hcd host code so that it can be built as a separate driver
module. This work is part of enabling multi-platform kernels on
ARM.

Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb at vger.kernel.org

V2:
 -Changed ohci_hcd and pxa27x_ohci struct variable names.
    1 ohci_hcd struct variable name is ohci.
    2 pxa27x_ohci struct variable name is pxa_ohci.

V3:
 -Rewrite the macro definition of to_pxa27x_ohci.
 -clk_put() function has been called before usb_put_hcd().
---
 drivers/usb/host/Kconfig       |    8 ++
 drivers/usb/host/Makefile      |    1 +
 drivers/usb/host/ohci-hcd.c    |    5 -
 drivers/usb/host/ohci-pxa27x.c |  242 ++++++++++++++++++----------------------
 4 files changed, 115 insertions(+), 141 deletions(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index cdfaa04..0d7ee36 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -422,6 +422,14 @@ config USB_OHCI_HCD_EP93XX
 	  Enables support for the on-chip OHCI controller on
 	  EP93XX chips.
 
+config USB_OHCI_HCD_PXA27X
+	tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
+	depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  PXA27x/PXA3xx chips.
+
 config USB_OHCI_HCD_AT91
         tristate "Support for Atmel on-chip OHCI USB controller"
         depends on USB_OHCI_HCD && ARCH_AT91
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 3fee3ea..8b7fa89 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_OHCI_HCD_S3CXXXX)	+= ohci-s3c2410.o
 obj-$(CONFIG_USB_OHCI_HCD_LPC32XX)	+= ohci-nxp.o
 obj-$(CONFIG_USB_OHCI_HCD_DA8XX)	+= ohci-da8xx.o
 obj-$(CONFIG_USB_OHCI_HCD_EP93XX)	+= ohci-ep93xx.o
+obj-$(CONFIG_USB_OHCI_HCD_PXA27X)	+= ohci-pxa27x.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 3f46cff..f601dde 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1184,11 +1184,6 @@ MODULE_LICENSE ("GPL");
 #define SA1111_DRIVER		ohci_hcd_sa1111_driver
 #endif
 
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#include "ohci-pxa27x.c"
-#define PLATFORM_DRIVER		ohci_hcd_pxa27x_driver
-#endif
-
 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 #include "ohci-ppc-of.c"
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 5fb91f1..394f221 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -19,15 +19,26 @@
  * This file is licenced under the GPL.
  */
 
-#include <linux/device.h>
-#include <linux/signal.h>
-#include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
-#include <mach/hardware.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
+#include <linux/platform_device.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+#include <linux/usb/otg.h>
+
+#include <mach/hardware.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI PXA27x/PXA3x driver"
 
 /*
  * UHC: USB Host Controller (OHCI-like) register definitions
@@ -101,16 +112,16 @@
 
 #define PXA_UHC_MAX_PORTNUM    3
 
-struct pxa27x_ohci {
-	/* must be 1st member here for hcd_to_ohci() to work */
-	struct ohci_hcd ohci;
+static const char hcd_name[] = "ohci-pxa27x";
+
+static struct hc_driver __read_mostly ohci_pxa27x_hc_driver;
 
-	struct device	*dev;
+struct pxa27x_ohci {
 	struct clk	*clk;
 	void __iomem	*mmio_base;
 };
 
-#define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)hcd_to_ohci(hcd)
+#define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
 
 /*
   PMM_NPS_MODE -- PMM Non-power switching mode
@@ -122,10 +133,10 @@ struct pxa27x_ohci {
   PMM_PERPORT_MODE -- PMM per port switching mode
       Ports are powered individually.
  */
-static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
+static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode)
 {
-	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
-	uint32_t uhcrhdb = __raw_readl(ohci->mmio_base + UHCRHDB);
+	uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
+	uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB);
 
 	switch (mode) {
 	case PMM_NPS_MODE:
@@ -149,20 +160,18 @@ static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
 		uhcrhda |= RH_A_NPS;
 	}
 
-	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
-	__raw_writel(uhcrhdb, ohci->mmio_base + UHCRHDB);
+	__raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
+	__raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB);
 	return 0;
 }
 
-extern int usb_disabled(void);
-
 /*-------------------------------------------------------------------------*/
 
-static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
+static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci,
 				   struct pxaohci_platform_data *inf)
 {
-	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
-	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
+	uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
+	uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
 
 	if (inf->flags & ENABLE_PORT1)
 		uhchr &= ~UHCHR_SSEP1;
@@ -194,17 +203,17 @@ static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
 		uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
 	}
 
-	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
-	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
+	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+	__raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
 }
 
-static inline void pxa27x_reset_hc(struct pxa27x_ohci *ohci)
+static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci)
 {
-	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
+	uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
 
-	__raw_writel(uhchr | UHCHR_FHR, ohci->mmio_base + UHCHR);
+	__raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
 	udelay(11);
-	__raw_writel(uhchr & ~UHCHR_FHR, ohci->mmio_base + UHCHR);
+	__raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
 }
 
 #ifdef CONFIG_PXA27x
@@ -213,25 +222,26 @@ extern void pxa27x_clear_otgph(void);
 #define pxa27x_clear_otgph()	do {} while (0)
 #endif
 
-static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
+static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
 {
 	int retval = 0;
 	struct pxaohci_platform_data *inf;
 	uint32_t uhchr;
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	inf = dev->platform_data;
 
-	clk_prepare_enable(ohci->clk);
+	clk_prepare_enable(pxa_ohci->clk);
 
-	pxa27x_reset_hc(ohci);
+	pxa27x_reset_hc(pxa_ohci);
 
-	uhchr = __raw_readl(ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
-	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
+	uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
+	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
 
-	while (__raw_readl(ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
+	while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
 		cpu_relax();
 
-	pxa27x_setup_hc(ohci, inf);
+	pxa27x_setup_hc(pxa_ohci, inf);
 
 	if (inf->init)
 		retval = inf->init(dev);
@@ -240,38 +250,39 @@ static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 		return retval;
 
 	if (cpu_is_pxa3xx())
-		pxa3xx_u2d_start_hc(&ohci_to_hcd(&ohci->ohci)->self);
+		pxa3xx_u2d_start_hc(&hcd->self);
 
-	uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
-	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
-	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, ohci->mmio_base + UHCHIE);
+	uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
+	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE);
 
 	/* Clear any OTG Pin Hold */
 	pxa27x_clear_otgph();
 	return 0;
 }
 
-static void pxa27x_stop_hc(struct pxa27x_ohci *ohci, struct device *dev)
+static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
 {
 	struct pxaohci_platform_data *inf;
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	uint32_t uhccoms;
 
 	inf = dev->platform_data;
 
 	if (cpu_is_pxa3xx())
-		pxa3xx_u2d_stop_hc(&ohci_to_hcd(&ohci->ohci)->self);
+		pxa3xx_u2d_stop_hc(&hcd->self);
 
 	if (inf->exit)
 		inf->exit(dev);
 
-	pxa27x_reset_hc(ohci);
+	pxa27x_reset_hc(pxa_ohci);
 
 	/* Host Controller Reset */
-	uhccoms = __raw_readl(ohci->mmio_base + UHCCOMS) | 0x01;
-	__raw_writel(uhccoms, ohci->mmio_base + UHCCOMS);
+	uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01;
+	__raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS);
 	udelay(10);
 
-	clk_disable_unprepare(ohci->clk);
+	clk_disable_unprepare(pxa_ohci->clk);
 }
 
 #ifdef CONFIG_OF
@@ -356,7 +367,8 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	int retval, irq;
 	struct usb_hcd *hcd;
 	struct pxaohci_platform_data *inf;
-	struct pxa27x_ohci *ohci;
+	struct pxa27x_ohci *pxa_ohci;
+	struct ohci_hcd *ohci;
 	struct resource *r;
 	struct clk *usb_clk;
 
@@ -409,29 +421,31 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	}
 
 	/* initialize "struct pxa27x_ohci" */
-	ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd);
-	ohci->dev = &pdev->dev;
-	ohci->clk = usb_clk;
-	ohci->mmio_base = (void __iomem *)hcd->regs;
+	pxa_ohci = to_pxa27x_ohci(hcd);
+	pxa_ohci->clk = usb_clk;
+	pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
 
-	if ((retval = pxa27x_start_hc(ohci, &pdev->dev)) < 0) {
+	retval = pxa27x_start_hc(pxa_ohci, &pdev->dev);
+	if (retval < 0) {
 		pr_debug("pxa27x_start_hc failed");
 		goto err3;
 	}
 
 	/* Select Power Management Mode */
-	pxa27x_ohci_select_pmm(ohci, inf->port_mode);
+	pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
 
 	if (inf->power_budget)
 		hcd->power_budget = inf->power_budget;
 
-	ohci_hcd_init(hcd_to_ohci(hcd));
+	/* The value of NDP in roothub_a is incorrect on this hardware */
+	ohci = hcd_to_ohci(hcd);
+	ohci->num_ports = 3;
 
 	retval = usb_add_hcd(hcd, irq, 0);
 	if (retval == 0)
 		return retval;
 
-	pxa27x_stop_hc(ohci, &pdev->dev);
+	pxa27x_stop_hc(pxa_ohci, &pdev->dev);
  err3:
 	iounmap(hcd->regs);
  err2:
@@ -459,88 +473,18 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
  */
 void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 {
-	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
 
 	usb_remove_hcd(hcd);
-	pxa27x_stop_hc(ohci, &pdev->dev);
+	pxa27x_stop_hc(pxa_ohci, &pdev->dev);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	clk_put(pxa_ohci->clk);
 	usb_put_hcd(hcd);
-	clk_put(ohci->clk);
-}
-
-/*-------------------------------------------------------------------------*/
-
-static int
-ohci_pxa27x_start (struct usb_hcd *hcd)
-{
-	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
-	int		ret;
-
-	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);
-
-	/* The value of NDP in roothub_a is incorrect on this hardware */
-	ohci->num_ports = 3;
-
-	if ((ret = ohci_init(ohci)) < 0)
-		return ret;
-
-	if ((ret = ohci_run (ohci)) < 0) {
-		dev_err(hcd->self.controller, "can't start %s",
-			hcd->self.bus_name);
-		ohci_stop (hcd);
-		return ret;
-	}
-
-	return 0;
 }
 
 /*-------------------------------------------------------------------------*/
 
-static const struct hc_driver ohci_pxa27x_hc_driver = {
-	.description =		hcd_name,
-	.product_desc =		"PXA27x OHCI",
-	.hcd_priv_size =	sizeof(struct pxa27x_ohci),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq =			ohci_irq,
-	.flags =		HCD_USB11 | HCD_MEMORY,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.start =		ohci_pxa27x_start,
-	.stop =			ohci_stop,
-	.shutdown =		ohci_shutdown,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue =		ohci_urb_enqueue,
-	.urb_dequeue =		ohci_urb_dequeue,
-	.endpoint_disable =	ohci_endpoint_disable,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number =	ohci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data =	ohci_hub_status_data,
-	.hub_control =		ohci_hub_control,
-#ifdef  CONFIG_PM
-	.bus_suspend =		ohci_bus_suspend,
-	.bus_resume =		ohci_bus_resume,
-#endif
-	.start_port_reset =	ohci_start_port_reset,
-};
-
-/*-------------------------------------------------------------------------*/
-
 static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
 {
 	pr_debug ("In ohci_hcd_pxa27x_drv_probe");
@@ -563,38 +507,43 @@ static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
 static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
 {
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
-	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
 	bool do_wakeup = device_may_wakeup(dev);
+	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	int ret;
 
-	if (time_before(jiffies, ohci->ohci.next_statechange))
+	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
-	ohci->ohci.next_statechange = jiffies;
+
+	ohci->next_statechange = jiffies;
 
 	ret = ohci_suspend(hcd, do_wakeup);
 	if (ret)
 		return ret;
 
-	pxa27x_stop_hc(ohci, dev);
+	pxa27x_stop_hc(pxa_ohci, dev);
 	return ret;
 }
 
 static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
 {
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
-	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
 	struct pxaohci_platform_data *inf = dev->platform_data;
+	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	int status;
 
-	if (time_before(jiffies, ohci->ohci.next_statechange))
+	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
-	ohci->ohci.next_statechange = jiffies;
 
-	if ((status = pxa27x_start_hc(ohci, dev)) < 0)
+	ohci->next_statechange = jiffies;
+
+	status = pxa27x_start_hc(pxa_ohci, dev);
+	if (status < 0)
 		return status;
 
 	/* Select Power Management Mode */
-	pxa27x_ohci_select_pmm(ohci, inf->port_mode);
+	pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
 
 	ohci_resume(hcd, false);
 	return 0;
@@ -606,9 +555,6 @@ static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
 };
 #endif
 
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:pxa27x-ohci");
-
 static struct platform_driver ohci_hcd_pxa27x_driver = {
 	.probe		= ohci_hcd_pxa27x_drv_probe,
 	.remove		= ohci_hcd_pxa27x_drv_remove,
@@ -623,3 +569,27 @@ static struct platform_driver ohci_hcd_pxa27x_driver = {
 	},
 };
 
+static const struct ohci_driver_overrides pxa27x_overrides __initconst = {
+	.extra_priv_size =      sizeof(struct pxa27x_ohci),
+};
+
+static int __init ohci_pxa27x_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+	ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides);
+	return platform_driver_register(&ohci_hcd_pxa27x_driver);
+}
+module_init(ohci_pxa27x_init);
+
+static void __exit ohci_pxa27x_cleanup(void)
+{
+	platform_driver_unregister(&ohci_hcd_pxa27x_driver);
+}
+module_exit(ohci_pxa27x_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pxa27x-ohci");
-- 
1.7.9.5

[PATCH V3 2/2] USB: OHCI: make ohci-pxa27x a separate driver

[Alan Stern]

On Fri, 26 Jul 2013, Manjunath Goudar wrote:

> Separate the  OHCI pxa27x/pxa3xx host controller driver from
> ohci-hcd host code so that it can be built as a separate driver
> module. This work is part of enabling multi-platform kernels on
> ARM.
> 
> Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
> Cc: Arnd Bergmann <arnd@arndb.de>
> Cc: Greg KH <greg@kroah.com>
> Cc: Alan Stern <stern@rowland.harvard.edu>
> Cc: linux-usb at vger.kernel.org
> 
> V2:
>  -Changed ohci_hcd and pxa27x_ohci struct variable names.
>     1 ohci_hcd struct variable name is ohci.
>     2 pxa27x_ohci struct variable name is pxa_ohci.
> 
> V3:
>  -Rewrite the macro definition of to_pxa27x_ohci.
>  -clk_put() function has been called before usb_put_hcd().

Acked-by: Alan Stern <stern@rowland.harvard.edu>

[PATCH V3 0/2] USB: OHCI: more bus glues as separate modules

[Manjunath Goudar]

These patches are for separating the SOC On-Chip ohci host controller
from ohci-hcd host code into its own driver module.
This work is part of enabling multi-platform kernels on ARM.

In V2:

patch 1/2:
     -ohci_hcd_init() statements are removed,
      because by default it is called in ohci_setup().

Patch 2/2:
     -Changed ohci_hcd and pxa27x_ohci struct variable names.
        1 ohci_hcd struct variable name is ohci.
        2 pxa27x_ohci struct variable name is pxa_ohci.

In V3:

Patch 1/2:
     -Unused *ohci variable has been removed.

patch 2/2:
     -Rewrite the macro definition of to_pxa27x_ohci.
     -clk_put() function has been called before usb_put_hcd().

Manjunath Goudar (2):
  USB: OHCI: make ohci-ep93xx a separate driver
  USB: OHCI: make ohci-pxa27x a separate driver

 drivers/usb/host/Kconfig       |   16 +++
 drivers/usb/host/Makefile      |    2 +
 drivers/usb/host/ohci-ep93xx.c |   80 ++++++-------
 drivers/usb/host/ohci-hcd.c    |   23 ----
 drivers/usb/host/ohci-pxa27x.c |  242 ++++++++++++++++++----------------------
 5 files changed, 158 insertions(+), 205 deletions(-)

-- 
1.7.9.5

[PATCH V3 1/2] USB: OHCI: make ohci-ep93xx a separate driver

[Manjunath Goudar]

Separate the OHCI EP93XX host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.

Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: linux-usb at vger.kernel.org

V2:
 -ohci_hcd_init() statements are removed,
  because by default it is called in ohci_setup().

V3:
 -Unused *ohci variable has been removed.
---
 drivers/usb/host/Kconfig       |    8 ++++
 drivers/usb/host/Makefile      |    1 +
 drivers/usb/host/ohci-ep93xx.c |   80 +++++++++++++++++-----------------------
 drivers/usb/host/ohci-hcd.c    |   18 ---------
 4 files changed, 43 insertions(+), 64 deletions(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index f7f7823..cdfaa04 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -414,6 +414,14 @@ config USB_OHCI_HCD_DA8XX
           Enables support for the on-chip OHCI controller on
           DA8xx/OMAP-L1x chips.
 
+config USB_OHCI_HCD_EP93XX
+	tristate "Support for EP93XX on-chip OHCI USB controller"
+	depends on USB_OHCI_HCD && ARCH_EP93XX
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  EP93XX chips.
+
 config USB_OHCI_HCD_AT91
         tristate "Support for Atmel on-chip OHCI USB controller"
         depends on USB_OHCI_HCD && ARCH_AT91
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index f8d59371..3fee3ea 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_USB_OHCI_HCD_AT91)	+= ohci-at91.o
 obj-$(CONFIG_USB_OHCI_HCD_S3CXXXX)	+= ohci-s3c2410.o
 obj-$(CONFIG_USB_OHCI_HCD_LPC32XX)	+= ohci-nxp.o
 obj-$(CONFIG_USB_OHCI_HCD_DA8XX)	+= ohci-da8xx.o
+obj-$(CONFIG_USB_OHCI_HCD_EP93XX)	+= ohci-ep93xx.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
diff --git a/drivers/usb/host/ohci-ep93xx.c b/drivers/usb/host/ohci-ep93xx.c
index f0aaa48..7b0e3ae 100644
--- a/drivers/usb/host/ohci-ep93xx.c
+++ b/drivers/usb/host/ohci-ep93xx.c
@@ -25,8 +25,21 @@
 
 #include <linux/clk.h>
 #include <linux/device.h>
-#include <linux/signal.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI EP93xx driver"
+
+static const char hcd_name[] = "ohci-ep93xx";
+
+static struct hc_driver __read_mostly ohci_ep93xx_hc_driver;
 
 static struct clk *usb_host_clock;
 
@@ -79,8 +92,6 @@ static int usb_hcd_ep93xx_probe(const struct hc_driver *driver,
 
 	ep93xx_start_hc(&pdev->dev);
 
-	ohci_hcd_init(hcd_to_ohci(hcd));
-
 	retval = usb_add_hcd(hcd, pdev->resource[1].start, 0);
 	if (retval == 0)
 		return retval;
@@ -107,48 +118,6 @@ static void usb_hcd_ep93xx_remove(struct usb_hcd *hcd,
 	usb_put_hcd(hcd);
 }
 
-static int ohci_ep93xx_start(struct usb_hcd *hcd)
-{
-	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
-	int ret;
-
-	if ((ret = ohci_init(ohci)) < 0)
-		return ret;
-
-	if ((ret = ohci_run(ohci)) < 0) {
-		dev_err(hcd->self.controller, "can't start %s\n",
-			hcd->self.bus_name);
-		ohci_stop(hcd);
-		return ret;
-	}
-
-	return 0;
-}
-
-static struct hc_driver ohci_ep93xx_hc_driver = {
-	.description		= hcd_name,
-	.product_desc		= "EP93xx OHCI",
-	.hcd_priv_size		= sizeof(struct ohci_hcd),
-	.irq			= ohci_irq,
-	.flags			= HCD_USB11 | HCD_MEMORY,
-	.start			= ohci_ep93xx_start,
-	.stop			= ohci_stop,
-	.shutdown		= ohci_shutdown,
-	.urb_enqueue		= ohci_urb_enqueue,
-	.urb_dequeue		= ohci_urb_dequeue,
-	.endpoint_disable	= ohci_endpoint_disable,
-	.get_frame_number	= ohci_get_frame,
-	.hub_status_data	= ohci_hub_status_data,
-	.hub_control		= ohci_hub_control,
-#ifdef CONFIG_PM
-	.bus_suspend		= ohci_bus_suspend,
-	.bus_resume		= ohci_bus_resume,
-#endif
-	.start_port_reset	= ohci_start_port_reset,
-};
-
-extern int usb_disabled(void);
-
 static int ohci_hcd_ep93xx_drv_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -206,7 +175,6 @@ static int ohci_hcd_ep93xx_drv_resume(struct platform_device *pdev)
 }
 #endif
 
-
 static struct platform_driver ohci_hcd_ep93xx_driver = {
 	.probe		= ohci_hcd_ep93xx_drv_probe,
 	.remove		= ohci_hcd_ep93xx_drv_remove,
@@ -221,4 +189,24 @@ static struct platform_driver ohci_hcd_ep93xx_driver = {
 	},
 };
 
+static int __init ohci_ep93xx_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+
+	ohci_init_driver(&ohci_ep93xx_hc_driver, NULL);
+	return platform_driver_register(&ohci_hcd_ep93xx_driver);
+}
+module_init(ohci_ep93xx_init);
+
+static void __exit ohci_ep93xx_cleanup(void)
+{
+	platform_driver_unregister(&ohci_hcd_ep93xx_driver);
+}
+module_exit(ohci_ep93xx_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:ep93xx-ohci");
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 6ae5520..3f46cff 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1189,11 +1189,6 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ohci_hcd_pxa27x_driver
 #endif
 
-#ifdef CONFIG_ARCH_EP93XX
-#include "ohci-ep93xx.c"
-#define EP93XX_PLATFORM_DRIVER	ohci_hcd_ep93xx_driver
-#endif
-
 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 #include "ohci-ppc-of.c"
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
@@ -1284,19 +1279,9 @@ static int __init ohci_hcd_mod_init(void)
 	if (retval < 0)
 		goto error_tmio;
 #endif
-
-#ifdef EP93XX_PLATFORM_DRIVER
-	retval = platform_driver_register(&EP93XX_PLATFORM_DRIVER);
-	if (retval < 0)
-		goto error_ep93xx;
-#endif
 	return retval;
 
 	/* Error path */
-#ifdef EP93XX_PLATFORM_DRIVER
-	platform_driver_unregister(&EP93XX_PLATFORM_DRIVER);
- error_ep93xx:
-#endif
 #ifdef TMIO_OHCI_DRIVER
 	platform_driver_unregister(&TMIO_OHCI_DRIVER);
  error_tmio:
@@ -1334,9 +1319,6 @@ module_init(ohci_hcd_mod_init);
 
 static void __exit ohci_hcd_mod_exit(void)
 {
-#ifdef EP93XX_PLATFORM_DRIVER
-	platform_driver_unregister(&EP93XX_PLATFORM_DRIVER);
-#endif
 #ifdef TMIO_OHCI_DRIVER
 	platform_driver_unregister(&TMIO_OHCI_DRIVER);
 #endif
-- 
1.7.9.5

[PATCH V3 2/2] USB: OHCI: make ohci-pxa27x a separate driver

[Manjunath Goudar]

Separate the  OHCI pxa27x/pxa3xx host controller driver from
ohci-hcd host code so that it can be built as a separate driver
module. This work is part of enabling multi-platform kernels on
ARM.

Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: linux-usb at vger.kernel.org

V2:
 -Changed ohci_hcd and pxa27x_ohci struct variable names.
    1 ohci_hcd struct variable name is ohci.
    2 pxa27x_ohci struct variable name is pxa_ohci.

V3:
 -Rewrite the macro definition of to_pxa27x_ohci.
 -clk_put() function has been called before usb_put_hcd().
---
 drivers/usb/host/Kconfig       |    8 ++
 drivers/usb/host/Makefile      |    1 +
 drivers/usb/host/ohci-hcd.c    |    5 -
 drivers/usb/host/ohci-pxa27x.c |  242 ++++++++++++++++++----------------------
 4 files changed, 115 insertions(+), 141 deletions(-)

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index cdfaa04..0d7ee36 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -422,6 +422,14 @@ config USB_OHCI_HCD_EP93XX
 	  Enables support for the on-chip OHCI controller on
 	  EP93XX chips.
 
+config USB_OHCI_HCD_PXA27X
+	tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
+	depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
+	default y
+	---help---
+	  Enables support for the on-chip OHCI controller on
+	  PXA27x/PXA3xx chips.
+
 config USB_OHCI_HCD_AT91
         tristate "Support for Atmel on-chip OHCI USB controller"
         depends on USB_OHCI_HCD && ARCH_AT91
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 3fee3ea..8b7fa89 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_OHCI_HCD_S3CXXXX)	+= ohci-s3c2410.o
 obj-$(CONFIG_USB_OHCI_HCD_LPC32XX)	+= ohci-nxp.o
 obj-$(CONFIG_USB_OHCI_HCD_DA8XX)	+= ohci-da8xx.o
 obj-$(CONFIG_USB_OHCI_HCD_EP93XX)	+= ohci-ep93xx.o
+obj-$(CONFIG_USB_OHCI_HCD_PXA27X)	+= ohci-pxa27x.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 3f46cff..f601dde 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1184,11 +1184,6 @@ MODULE_LICENSE ("GPL");
 #define SA1111_DRIVER		ohci_hcd_sa1111_driver
 #endif
 
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#include "ohci-pxa27x.c"
-#define PLATFORM_DRIVER		ohci_hcd_pxa27x_driver
-#endif
-
 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 #include "ohci-ppc-of.c"
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 5fb91f1..394f221 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -19,15 +19,26 @@
  * This file is licenced under the GPL.
  */
 
-#include <linux/device.h>
-#include <linux/signal.h>
-#include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
-#include <mach/hardware.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
+#include <linux/platform_device.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+#include <linux/usb/otg.h>
+
+#include <mach/hardware.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI PXA27x/PXA3x driver"
 
 /*
  * UHC: USB Host Controller (OHCI-like) register definitions
@@ -101,16 +112,16 @@
 
 #define PXA_UHC_MAX_PORTNUM    3
 
-struct pxa27x_ohci {
-	/* must be 1st member here for hcd_to_ohci() to work */
-	struct ohci_hcd ohci;
+static const char hcd_name[] = "ohci-pxa27x";
+
+static struct hc_driver __read_mostly ohci_pxa27x_hc_driver;
 
-	struct device	*dev;
+struct pxa27x_ohci {
 	struct clk	*clk;
 	void __iomem	*mmio_base;
 };
 
-#define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)hcd_to_ohci(hcd)
+#define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
 
 /*
   PMM_NPS_MODE -- PMM Non-power switching mode
@@ -122,10 +133,10 @@ struct pxa27x_ohci {
   PMM_PERPORT_MODE -- PMM per port switching mode
       Ports are powered individually.
  */
-static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
+static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode)
 {
-	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
-	uint32_t uhcrhdb = __raw_readl(ohci->mmio_base + UHCRHDB);
+	uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
+	uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB);
 
 	switch (mode) {
 	case PMM_NPS_MODE:
@@ -149,20 +160,18 @@ static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
 		uhcrhda |= RH_A_NPS;
 	}
 
-	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
-	__raw_writel(uhcrhdb, ohci->mmio_base + UHCRHDB);
+	__raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
+	__raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB);
 	return 0;
 }
 
-extern int usb_disabled(void);
-
 /*-------------------------------------------------------------------------*/
 
-static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
+static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci,
 				   struct pxaohci_platform_data *inf)
 {
-	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
-	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
+	uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
+	uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
 
 	if (inf->flags & ENABLE_PORT1)
 		uhchr &= ~UHCHR_SSEP1;
@@ -194,17 +203,17 @@ static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
 		uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
 	}
 
-	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
-	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
+	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+	__raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
 }
 
-static inline void pxa27x_reset_hc(struct pxa27x_ohci *ohci)
+static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci)
 {
-	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
+	uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
 
-	__raw_writel(uhchr | UHCHR_FHR, ohci->mmio_base + UHCHR);
+	__raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
 	udelay(11);
-	__raw_writel(uhchr & ~UHCHR_FHR, ohci->mmio_base + UHCHR);
+	__raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
 }
 
 #ifdef CONFIG_PXA27x
@@ -213,25 +222,26 @@ extern void pxa27x_clear_otgph(void);
 #define pxa27x_clear_otgph()	do {} while (0)
 #endif
 
-static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
+static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
 {
 	int retval = 0;
 	struct pxaohci_platform_data *inf;
 	uint32_t uhchr;
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	inf = dev->platform_data;
 
-	clk_prepare_enable(ohci->clk);
+	clk_prepare_enable(pxa_ohci->clk);
 
-	pxa27x_reset_hc(ohci);
+	pxa27x_reset_hc(pxa_ohci);
 
-	uhchr = __raw_readl(ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
-	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
+	uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
+	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
 
-	while (__raw_readl(ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
+	while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
 		cpu_relax();
 
-	pxa27x_setup_hc(ohci, inf);
+	pxa27x_setup_hc(pxa_ohci, inf);
 
 	if (inf->init)
 		retval = inf->init(dev);
@@ -240,38 +250,39 @@ static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 		return retval;
 
 	if (cpu_is_pxa3xx())
-		pxa3xx_u2d_start_hc(&ohci_to_hcd(&ohci->ohci)->self);
+		pxa3xx_u2d_start_hc(&hcd->self);
 
-	uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
-	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
-	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, ohci->mmio_base + UHCHIE);
+	uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
+	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE);
 
 	/* Clear any OTG Pin Hold */
 	pxa27x_clear_otgph();
 	return 0;
 }
 
-static void pxa27x_stop_hc(struct pxa27x_ohci *ohci, struct device *dev)
+static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
 {
 	struct pxaohci_platform_data *inf;
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	uint32_t uhccoms;
 
 	inf = dev->platform_data;
 
 	if (cpu_is_pxa3xx())
-		pxa3xx_u2d_stop_hc(&ohci_to_hcd(&ohci->ohci)->self);
+		pxa3xx_u2d_stop_hc(&hcd->self);
 
 	if (inf->exit)
 		inf->exit(dev);
 
-	pxa27x_reset_hc(ohci);
+	pxa27x_reset_hc(pxa_ohci);
 
 	/* Host Controller Reset */
-	uhccoms = __raw_readl(ohci->mmio_base + UHCCOMS) | 0x01;
-	__raw_writel(uhccoms, ohci->mmio_base + UHCCOMS);
+	uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01;
+	__raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS);
 	udelay(10);
 
-	clk_disable_unprepare(ohci->clk);
+	clk_disable_unprepare(pxa_ohci->clk);
 }
 
 #ifdef CONFIG_OF
@@ -356,7 +367,8 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	int retval, irq;
 	struct usb_hcd *hcd;
 	struct pxaohci_platform_data *inf;
-	struct pxa27x_ohci *ohci;
+	struct pxa27x_ohci *pxa_ohci;
+	struct ohci_hcd *ohci;
 	struct resource *r;
 	struct clk *usb_clk;
 
@@ -409,29 +421,31 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	}
 
 	/* initialize "struct pxa27x_ohci" */
-	ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd);
-	ohci->dev = &pdev->dev;
-	ohci->clk = usb_clk;
-	ohci->mmio_base = (void __iomem *)hcd->regs;
+	pxa_ohci = to_pxa27x_ohci(hcd);
+	pxa_ohci->clk = usb_clk;
+	pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
 
-	if ((retval = pxa27x_start_hc(ohci, &pdev->dev)) < 0) {
+	retval = pxa27x_start_hc(pxa_ohci, &pdev->dev);
+	if (retval < 0) {
 		pr_debug("pxa27x_start_hc failed");
 		goto err3;
 	}
 
 	/* Select Power Management Mode */
-	pxa27x_ohci_select_pmm(ohci, inf->port_mode);
+	pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
 
 	if (inf->power_budget)
 		hcd->power_budget = inf->power_budget;
 
-	ohci_hcd_init(hcd_to_ohci(hcd));
+	/* The value of NDP in roothub_a is incorrect on this hardware */
+	ohci = hcd_to_ohci(hcd);
+	ohci->num_ports = 3;
 
 	retval = usb_add_hcd(hcd, irq, 0);
 	if (retval == 0)
 		return retval;
 
-	pxa27x_stop_hc(ohci, &pdev->dev);
+	pxa27x_stop_hc(pxa_ohci, &pdev->dev);
  err3:
 	iounmap(hcd->regs);
  err2:
@@ -459,88 +473,18 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
  */
 void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 {
-	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
 
 	usb_remove_hcd(hcd);
-	pxa27x_stop_hc(ohci, &pdev->dev);
+	pxa27x_stop_hc(pxa_ohci, &pdev->dev);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	clk_put(pxa_ohci->clk);
 	usb_put_hcd(hcd);
-	clk_put(ohci->clk);
-}
-
-/*-------------------------------------------------------------------------*/
-
-static int
-ohci_pxa27x_start (struct usb_hcd *hcd)
-{
-	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
-	int		ret;
-
-	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);
-
-	/* The value of NDP in roothub_a is incorrect on this hardware */
-	ohci->num_ports = 3;
-
-	if ((ret = ohci_init(ohci)) < 0)
-		return ret;
-
-	if ((ret = ohci_run (ohci)) < 0) {
-		dev_err(hcd->self.controller, "can't start %s",
-			hcd->self.bus_name);
-		ohci_stop (hcd);
-		return ret;
-	}
-
-	return 0;
 }
 
 /*-------------------------------------------------------------------------*/
 
-static const struct hc_driver ohci_pxa27x_hc_driver = {
-	.description =		hcd_name,
-	.product_desc =		"PXA27x OHCI",
-	.hcd_priv_size =	sizeof(struct pxa27x_ohci),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq =			ohci_irq,
-	.flags =		HCD_USB11 | HCD_MEMORY,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.start =		ohci_pxa27x_start,
-	.stop =			ohci_stop,
-	.shutdown =		ohci_shutdown,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue =		ohci_urb_enqueue,
-	.urb_dequeue =		ohci_urb_dequeue,
-	.endpoint_disable =	ohci_endpoint_disable,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number =	ohci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data =	ohci_hub_status_data,
-	.hub_control =		ohci_hub_control,
-#ifdef  CONFIG_PM
-	.bus_suspend =		ohci_bus_suspend,
-	.bus_resume =		ohci_bus_resume,
-#endif
-	.start_port_reset =	ohci_start_port_reset,
-};
-
-/*-------------------------------------------------------------------------*/
-
 static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
 {
 	pr_debug ("In ohci_hcd_pxa27x_drv_probe");
@@ -563,38 +507,43 @@ static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
 static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
 {
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
-	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
 	bool do_wakeup = device_may_wakeup(dev);
+	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	int ret;
 
-	if (time_before(jiffies, ohci->ohci.next_statechange))
+	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
-	ohci->ohci.next_statechange = jiffies;
+
+	ohci->next_statechange = jiffies;
 
 	ret = ohci_suspend(hcd, do_wakeup);
 	if (ret)
 		return ret;
 
-	pxa27x_stop_hc(ohci, dev);
+	pxa27x_stop_hc(pxa_ohci, dev);
 	return ret;
 }
 
 static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
 {
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
-	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
 	struct pxaohci_platform_data *inf = dev->platform_data;
+	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	int status;
 
-	if (time_before(jiffies, ohci->ohci.next_statechange))
+	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
-	ohci->ohci.next_statechange = jiffies;
 
-	if ((status = pxa27x_start_hc(ohci, dev)) < 0)
+	ohci->next_statechange = jiffies;
+
+	status = pxa27x_start_hc(pxa_ohci, dev);
+	if (status < 0)
 		return status;
 
 	/* Select Power Management Mode */
-	pxa27x_ohci_select_pmm(ohci, inf->port_mode);
+	pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
 
 	ohci_resume(hcd, false);
 	return 0;
@@ -606,9 +555,6 @@ static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
 };
 #endif
 
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:pxa27x-ohci");
-
 static struct platform_driver ohci_hcd_pxa27x_driver = {
 	.probe		= ohci_hcd_pxa27x_drv_probe,
 	.remove		= ohci_hcd_pxa27x_drv_remove,
@@ -623,3 +569,27 @@ static struct platform_driver ohci_hcd_pxa27x_driver = {
 	},
 };
 
+static const struct ohci_driver_overrides pxa27x_overrides __initconst = {
+	.extra_priv_size =      sizeof(struct pxa27x_ohci),
+};
+
+static int __init ohci_pxa27x_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+	ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides);
+	return platform_driver_register(&ohci_hcd_pxa27x_driver);
+}
+module_init(ohci_pxa27x_init);
+
+static void __exit ohci_pxa27x_cleanup(void)
+{
+	platform_driver_unregister(&ohci_hcd_pxa27x_driver);
+}
+module_exit(ohci_pxa27x_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pxa27x-ohci");
-- 
1.7.9.5

[PATCH V3 1/2] USB: OHCI: make ohci-ep93xx a separate driver

[Greg KH]

On Sat, Aug 10, 2013 at 01:11:39PM +0530, Manjunath Goudar wrote:
> Separate the OHCI EP93XX host controller driver from ohci-hcd
> host code so that it can be built as a separate driver module.
> This work is part of enabling multi-platform kernels on ARM.
> 
> Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
> Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
> Acked-by: Alan Stern <stern@rowland.harvard.edu>
> Cc: Arnd Bergmann <arnd@arndb.de>
> Cc: Greg KH <greg@kroah.com>
> Cc: linux-usb at vger.kernel.org
> 
> V2:
>  -ohci_hcd_init() statements are removed,
>   because by default it is called in ohci_setup().
> 
> V3:
>  -Unused *ohci variable has been removed.
> ---
>  drivers/usb/host/Kconfig       |    8 ++++
>  drivers/usb/host/Makefile      |    1 +
>  drivers/usb/host/ohci-ep93xx.c |   80 +++++++++++++++++-----------------------
>  drivers/usb/host/ohci-hcd.c    |   18 ---------
>  4 files changed, 43 insertions(+), 64 deletions(-)

This too fails to apply:

$ p1 < ../s1
checking file drivers/usb/host/Kconfig
Hunk #1 FAILED at 414.
1 out of 1 hunk FAILED
checking file drivers/usb/host/Makefile
Hunk #1 FAILED at 54.
1 out of 1 hunk FAILED
checking file drivers/usb/host/ohci-ep93xx.c
Hunk #2 FAILED at 92.
Hunk #3 FAILED at 120.
Hunk #4 succeeded at 179 (offset -40 lines).
Hunk #5 succeeded@193 (offset -40 lines).
2 out of 5 hunks FAILED
checking file drivers/usb/host/ohci-hcd.c
Reversed (or previously applied) patch detected!  Assume -R? [n] 
Apply anyway? [n] 
Skipping patch.
3 out of 3 hunks ignored


Can you respin _all_ of your pending patches you have sent me in a
format that I can apply them, and resend them in a series that shows
what should be applied in which order.  As it is, I have 3-4 different
series of patches from you, with no obvious order which should be
applied in which order.  Because of that, that might be why these aren't
applying.

thanks,

greg k-h