[PATCH v2 1/2] MIPS: BCM47XX: Remove CFE support

[PATCH v2 1/2] MIPS: BCM47XX: Remove CFE support

[Hauke Mehrtens]

bcm47xx only uses the CFE code for early print to a console, but that
is also possible with a early print serial 8250 driver.

The CFE api init causes hangs somewhere in prom_init_cfe() on some
devices like the Buffalo WHR-HP-G54 and the Asus WL-520GU.
This was reported in https://dev.openwrt.org/ticket/4061 and
https://forum.openwrt.org/viewtopic.php?id=17063

This will remove all the CFE handling code from bcm47xx.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
---
 arch/mips/Kconfig        |    2 -
 arch/mips/bcm47xx/prom.c |   91 ----------------------------------------------
 2 files changed, 93 deletions(-)

diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index e70cf31..f73cb81 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -111,14 +111,12 @@ config BCM47XX
 	select CEVT_R4K
 	select CSRC_R4K
 	select DMA_NONCOHERENT
-	select FW_CFE
 	select HW_HAS_PCI
 	select IRQ_CPU
 	select SYS_HAS_CPU_MIPS32_R1
 	select NO_EXCEPT_FILL
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_HAS_EARLY_PRINTK
 	help
 	 Support for BCM47XX based boards
 
diff --git a/arch/mips/bcm47xx/prom.c b/arch/mips/bcm47xx/prom.c
index 53b9a3fb..99c3ce2 100644
--- a/arch/mips/bcm47xx/prom.c
+++ b/arch/mips/bcm47xx/prom.c
@@ -30,12 +30,9 @@
 #include <linux/spinlock.h>
 #include <linux/smp.h>
 #include <asm/bootinfo.h>
-#include <asm/fw/cfe/cfe_api.h>
-#include <asm/fw/cfe/cfe_error.h>
 #include <bcm47xx.h>
 #include <bcm47xx_board.h>
 
-static int cfe_cons_handle;
 
 static char bcm47xx_system_type[20] = "Broadcom BCM47XX";
 
@@ -52,91 +49,6 @@ __init void bcm47xx_set_system_type(u16 chip_id)
 		 chip_id);
 }
 
-void prom_putchar(char c)
-{
-	while (cfe_write(cfe_cons_handle, &c, 1) == 0)
-		;
-}
-
-static __init void prom_init_cfe(void)
-{
-	uint32_t cfe_ept;
-	uint32_t cfe_handle;
-	uint32_t cfe_eptseal;
-	int argc = fw_arg0;
-	char **envp = (char **) fw_arg2;
-	int *prom_vec = (int *) fw_arg3;
-
-	/*
-	 * Check if a loader was used; if NOT, the 4 arguments are
-	 * what CFE gives us (handle, 0, EPT and EPTSEAL)
-	 */
-	if (argc < 0) {
-		cfe_handle = (uint32_t)argc;
-		cfe_ept = (uint32_t)envp;
-		cfe_eptseal = (uint32_t)prom_vec;
-	} else {
-		if ((int)prom_vec < 0) {
-			/*
-			 * Old loader; all it gives us is the handle,
-			 * so use the "known" entrypoint and assume
-			 * the seal.
-			 */
-			cfe_handle = (uint32_t)prom_vec;
-			cfe_ept = 0xBFC00500;
-			cfe_eptseal = CFE_EPTSEAL;
-		} else {
-			/*
-			 * Newer loaders bundle the handle/ept/eptseal
-			 * Note: prom_vec is in the loader's useg
-			 * which is still alive in the TLB.
-			 */
-			cfe_handle = prom_vec[0];
-			cfe_ept = prom_vec[2];
-			cfe_eptseal = prom_vec[3];
-		}
-	}
-
-	if (cfe_eptseal != CFE_EPTSEAL) {
-		/* too early for panic to do any good */
-		printk(KERN_ERR "CFE's entrypoint seal doesn't match.");
-		while (1) ;
-	}
-
-	cfe_init(cfe_handle, cfe_ept);
-}
-
-static __init void prom_init_console(void)
-{
-	/* Initialize CFE console */
-	cfe_cons_handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE);
-}
-
-static __init void prom_init_cmdline(void)
-{
-	static char buf[COMMAND_LINE_SIZE] __initdata;
-
-	/* Get the kernel command line from CFE */
-	if (cfe_getenv("LINUX_CMDLINE", buf, COMMAND_LINE_SIZE) >= 0) {
-		buf[COMMAND_LINE_SIZE - 1] = 0;
-		strcpy(arcs_cmdline, buf);
-	}
-
-	/* Force a console handover by adding a console= argument if needed,
-	 * as CFE is not available anymore later in the boot process. */
-	if ((strstr(arcs_cmdline, "console=")) == NULL) {
-		/* Try to read the default serial port used by CFE */
-		if ((cfe_getenv("BOOT_CONSOLE", buf, COMMAND_LINE_SIZE) < 0)
-		    || (strncmp("uart", buf, 4)))
-			/* Default to uart0 */
-			strcpy(buf, "uart0");
-
-		/* Compute the new command line */
-		snprintf(arcs_cmdline, COMMAND_LINE_SIZE, "%s console=ttyS%c,115200",
-			 arcs_cmdline, buf[4]);
-	}
-}
-
 static __init void prom_init_mem(void)
 {
 	unsigned long mem;
@@ -184,9 +96,6 @@ static __init void prom_init_mem(void)
 
 void __init prom_init(void)
 {
-	prom_init_cfe();
-	prom_init_console();
-	prom_init_cmdline();
 	prom_init_mem();
 }
 
-- 
1.7.10.4

[PATCH v2 2/2] MIPS: BCM47XX: add EARLY_PRINTK_8250 support

[Hauke Mehrtens]

The BCM47xx SoCs have a 8250 serial compatible console at address
0xb8000300 and an other at 0xb8000400. On most devices 0xb8000300 is
wired to some pins on the board, we should use that.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
---
 arch/mips/Kconfig        |    2 ++
 arch/mips/bcm47xx/prom.c |    1 +
 2 files changed, 3 insertions(+)

diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index f73cb81..02a3a66 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -117,6 +117,8 @@ config BCM47XX
 	select NO_EXCEPT_FILL
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+	select EARLY_PRINTK_8250 if EARLY_PRINTK
 	help
 	 Support for BCM47XX based boards
 
diff --git a/arch/mips/bcm47xx/prom.c b/arch/mips/bcm47xx/prom.c
index 99c3ce2..31f7acd 100644
--- a/arch/mips/bcm47xx/prom.c
+++ b/arch/mips/bcm47xx/prom.c
@@ -97,6 +97,7 @@ static __init void prom_init_mem(void)
 void __init prom_init(void)
 {
 	prom_init_mem();
+	setup_8250_early_printk_port(0xb8000300, 0, 0);
 }
 
 void __init prom_free_prom_memory(void)
-- 
1.7.10.4