* [PATCH 00/21] ARM: ux500: pin control device tree migration
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This patch series migrated all the pin control information
for the Nomadik pin controller as used on the various Ux500
boards from the board file and into the device tree.
After this only the ABx500 pin configuration remains in the
board file. (Will be addressed separately.)
This uses the existing device tree bindings. No new bindings
are added.
Linus Walleij (21):
ARM: ux500: move UART pin control to the device tree
ARM: ux500: move I2C pin control to the device tree
ARM: ux500: move MMC/SD/SDIO pin control to the device tree
ARM: ux500: move MSP pin control to the device tree
ARM: ux500: move GPIO217/218 config to device tree
ARM: ux500: move MUSB pin config to device tree
ARM: ux500: move SPI pin config to device tree
ARM: ux500: create MCDE node to collect resources
ARM: ux500: move MCDE pin config to device tree
ARM: ux500: move SKE pin config to device tree
ARM: ux500: drop STM pinmap settings
ARM: ux500: move old HREF ipgpio to the device tree
ARM: ux500: move GPIO key configuration to device tree
ARM: ux500: move the WLAN GPIO pin setup to the device tree
ARM: ux500: move the HREFv60plus IPGPIO pins to device tree
ARM: ux500: move final HREFv60 LCD pins to device tree
ARM: ux500: move HREFv60plus pin configs to device tree
ARM: ux500: move snowball ethernet config to device tree
ARM: ux500: convert Snowball SPI pin reference
ARM: ux500: move snowball LED pin control to device tree
ARM: ux500: move snowball pin configs to device tree
arch/arm/boot/dts/ste-dbx5x0.dtsi | 17 +
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 745 +++++++++++++++++++++++
arch/arm/boot/dts/ste-href-stuib.dtsi | 41 ++
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 51 ++
arch/arm/boot/dts/ste-href.dtsi | 78 ++-
arch/arm/boot/dts/ste-hrefprev60.dtsi | 65 ++
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 217 ++++++-
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 80 +++
arch/arm/boot/dts/ste-snowball.dts | 225 +++++++
arch/arm/mach-ux500/board-mop500-pins.c | 781 -------------------------
10 files changed, 1503 insertions(+), 797 deletions(-)
create mode 100644 arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 44+ messages in thread
* [PATCH 00/21] ARM: ux500: pin control device tree migration
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This patch series migrated all the pin control information
for the Nomadik pin controller as used on the various Ux500
boards from the board file and into the device tree.
After this only the ABx500 pin configuration remains in the
board file. (Will be addressed separately.)
This uses the existing device tree bindings. No new bindings
are added.
Linus Walleij (21):
ARM: ux500: move UART pin control to the device tree
ARM: ux500: move I2C pin control to the device tree
ARM: ux500: move MMC/SD/SDIO pin control to the device tree
ARM: ux500: move MSP pin control to the device tree
ARM: ux500: move GPIO217/218 config to device tree
ARM: ux500: move MUSB pin config to device tree
ARM: ux500: move SPI pin config to device tree
ARM: ux500: create MCDE node to collect resources
ARM: ux500: move MCDE pin config to device tree
ARM: ux500: move SKE pin config to device tree
ARM: ux500: drop STM pinmap settings
ARM: ux500: move old HREF ipgpio to the device tree
ARM: ux500: move GPIO key configuration to device tree
ARM: ux500: move the WLAN GPIO pin setup to the device tree
ARM: ux500: move the HREFv60plus IPGPIO pins to device tree
ARM: ux500: move final HREFv60 LCD pins to device tree
ARM: ux500: move HREFv60plus pin configs to device tree
ARM: ux500: move snowball ethernet config to device tree
ARM: ux500: convert Snowball SPI pin reference
ARM: ux500: move snowball LED pin control to device tree
ARM: ux500: move snowball pin configs to device tree
arch/arm/boot/dts/ste-dbx5x0.dtsi | 17 +
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 745 +++++++++++++++++++++++
arch/arm/boot/dts/ste-href-stuib.dtsi | 41 ++
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 51 ++
arch/arm/boot/dts/ste-href.dtsi | 78 ++-
arch/arm/boot/dts/ste-hrefprev60.dtsi | 65 ++
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 217 ++++++-
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 80 +++
arch/arm/boot/dts/ste-snowball.dts | 225 +++++++
arch/arm/mach-ux500/board-mop500-pins.c | 781 -------------------------
10 files changed, 1503 insertions(+), 797 deletions(-)
create mode 100644 arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
--
1.8.3.1
^ permalink raw reply [flat|nested] 44+ messages in thread
* [PATCH 01/21] ARM: ux500: move UART pin control to the device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij, Patrice Chotard
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.
We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.
Cc: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Patrice Chotard <patrice.chotard-qxv4g6HH51o@public.gmane.org>
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 114 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 10 +++
arch/arm/boot/dts/ste-snowball.dts | 10 +++
arch/arm/mach-ux500/board-mop500-pins.c | 52 -----------
4 files changed, 134 insertions(+), 52 deletions(-)
create mode 100644 arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
new file mode 100644
index 000000000000..d979de27b6e1
--- /dev/null
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -0,0 +1,114 @@
+/*
+ * Copyright 2013 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "ste-nomadik-pinctrl.dtsi"
+
+/ {
+ soc {
+ pinctrl {
+ /* Settings for all UART default and sleep states */
+ uart0 {
+ uart0_default_mode: uart0_default {
+ default_mux {
+ ste,function = "u0";
+ ste,pins = "u0_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart0_sleep_mode: uart0_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO1_AJ3"; /* RTS */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+
+ sleep_cfg3 {
+ ste,pins = "GPIO3_AH3"; /* TXD */
+ ste,config = <&slpm_out_wkup_pdis>;
+ };
+ };
+ };
+
+ uart1 {
+ uart1_default_mode: uart1_default {
+ default_mux {
+ ste,function = "u1";
+ ste,pins = "u1rxtx_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO4_AH6"; /* RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO5_AG6"; /* TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart1_sleep_mode: uart1_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO4_AH6"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO5_AG6"; /* TXD */
+ ste,config = <&slpm_out_wkup_pdis>;
+ };
+ };
+ };
+
+ uart2 {
+ uart2_default_mode: uart2_default {
+ default_mux {
+ ste,function = "u2";
+ ste,pins = "u2rxtx_c_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO29_W2"; /* RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO30_W3"; /* TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart2_sleep_mode: uart2_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO29_W2"; /* RXD */
+ ste,config = <&in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO30_W3"; /* TXD */
+ ste,config = <&out_wkup_pdis>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index aa3f02060fdd..914a5f4399e5 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include "ste-dbx5x0.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
/ {
memory {
@@ -30,14 +31,23 @@
soc {
uart@80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart0_default_mode>;
+ pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
uart@80121000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_default_mode>;
+ pinctrl-1 = <&uart1_sleep_mode>;
status = "okay";
};
uart@80007000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart2_default_mode>;
+ pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index f0b39f835914..16d28863ef6e 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "ste-dbx5x0.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
/ {
model = "Calao Systems Snowball platform with device tree";
@@ -155,14 +156,23 @@
};
uart@80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart0_default_mode>;
+ pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
uart@80121000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_default_mode>;
+ pinctrl-1 = <&uart1_sleep_mode>;
status = "okay";
};
uart@80007000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart2_default_mode>;
+ pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 0efb1560fc35..c6225191141f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -65,16 +65,12 @@ BIAS(slpm_in_nopull_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(slpm_out_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(in_wkup_pdis_en, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
PIN_SLPM_PDIS_ENABLED);
BIAS(in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
PIN_SLPM_PDIS_DISABLED);
-BIAS(out_wkup_pdis, PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_DISABLED);
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
@@ -376,50 +372,10 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
*/
DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
/*
- * UART0, we do not mux in u0 here.
- * uart-0 pins gpio configuration should be kept intact to prevent
- * a glitch in tx line when the tty dev is opened. Later these pins
- * are configured by uart driver
- */
- DB8500_PIN_HOG("GPIO0_AJ5", in_pu), /* CTS */
- DB8500_PIN_HOG("GPIO1_AJ3", out_hi), /* RTS */
- DB8500_PIN_HOG("GPIO2_AH4", in_pu), /* RXD */
- DB8500_PIN_HOG("GPIO3_AH3", out_hi), /* TXD */
- /*
- * Mux in UART2 on altfunction C and set pull-ups.
- * TODO: is this used on U8500 variants and Snowball really?
- * The setting on GPIO31 conflicts with magnetometer use on hrefv60
- */
- /* default state for UART2 */
- DB8500_MUX("u2rxtx_c_1", "u2", "uart2"),
- DB8500_PIN("GPIO29_W2", in_pu, "uart2"), /* RXD */
- DB8500_PIN("GPIO30_W3", out_hi, "uart2"), /* TXD */
- /* Sleep state for UART2 */
- DB8500_PIN_SLEEP("GPIO29_W2", in_wkup_pdis, "uart2"),
- DB8500_PIN_SLEEP("GPIO30_W3", out_wkup_pdis, "uart2"),
- /*
* The following pin sets were known as "runtime pins" before being
* converted to the pinctrl model. Here we model them as "default"
* states.
*/
- /* Mux in UART0 after initialization */
- DB8500_MUX("u0_a_1", "u0", "uart0"),
- DB8500_PIN("GPIO0_AJ5", in_pu, "uart0"), /* CTS */
- DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
- DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
- DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
- /* Sleep state for UART0 */
- DB8500_PIN_SLEEP("GPIO0_AJ5", slpm_in_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO1_AJ3", slpm_out_hi_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO2_AH4", slpm_in_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO3_AH3", slpm_out_wkup_pdis, "uart0"),
- /* Mux in UART1 after initialization */
- DB8500_MUX("u1rxtx_a_1", "u1", "uart1"),
- DB8500_PIN("GPIO4_AH6", in_pu, "uart1"), /* RXD */
- DB8500_PIN("GPIO5_AG6", out_hi, "uart1"), /* TXD */
- /* Sleep state for UART1 */
- DB8500_PIN_SLEEP("GPIO4_AH6", slpm_in_wkup_pdis, "uart1"),
- DB8500_PIN_SLEEP("GPIO5_AG6", slpm_out_wkup_pdis, "uart1"),
/* MSP1 for ALSA codec */
DB8500_MUX_HOG("msp1txrx_a_1", "msp1"),
DB8500_MUX_HOG("msp1_a_1", "msp1"),
@@ -822,10 +778,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
DB8500_PIN_HOG("GPIO7_AG5", in_pu),
/* TC35892 IRQ, pull up the line, let the driver mux in the pin */
DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
- /* Mux in UART1 and set the pull-ups */
- DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
- DB8500_PIN_HOG("GPIO4_AH6", in_pu), /* RXD */
- DB8500_PIN_HOG("GPIO5_AG6", out_hi), /* TXD */
/*
* Runtime stuff: make it possible to mux in the SKE keypad
* and bias the pins
@@ -971,10 +923,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
};
static struct pinctrl_map __initdata u9500_pinmap[] = {
- /* Mux in UART1 (just RX/TX) and set the pull-ups */
- DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
- DB8500_PIN_HOG("GPIO4_AH6", in_pu),
- DB8500_PIN_HOG("GPIO5_AG6", out_hi),
/* WLAN_IRQ line */
DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu),
/* HSI */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 01/21] ARM: ux500: move UART pin control to the device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.
We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 114 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 10 +++
arch/arm/boot/dts/ste-snowball.dts | 10 +++
arch/arm/mach-ux500/board-mop500-pins.c | 52 -----------
4 files changed, 134 insertions(+), 52 deletions(-)
create mode 100644 arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
new file mode 100644
index 000000000000..d979de27b6e1
--- /dev/null
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -0,0 +1,114 @@
+/*
+ * Copyright 2013 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "ste-nomadik-pinctrl.dtsi"
+
+/ {
+ soc {
+ pinctrl {
+ /* Settings for all UART default and sleep states */
+ uart0 {
+ uart0_default_mode: uart0_default {
+ default_mux {
+ ste,function = "u0";
+ ste,pins = "u0_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart0_sleep_mode: uart0_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO1_AJ3"; /* RTS */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+
+ sleep_cfg3 {
+ ste,pins = "GPIO3_AH3"; /* TXD */
+ ste,config = <&slpm_out_wkup_pdis>;
+ };
+ };
+ };
+
+ uart1 {
+ uart1_default_mode: uart1_default {
+ default_mux {
+ ste,function = "u1";
+ ste,pins = "u1rxtx_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO4_AH6"; /* RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO5_AG6"; /* TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart1_sleep_mode: uart1_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO4_AH6"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO5_AG6"; /* TXD */
+ ste,config = <&slpm_out_wkup_pdis>;
+ };
+ };
+ };
+
+ uart2 {
+ uart2_default_mode: uart2_default {
+ default_mux {
+ ste,function = "u2";
+ ste,pins = "u2rxtx_c_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO29_W2"; /* RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO30_W3"; /* TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart2_sleep_mode: uart2_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO29_W2"; /* RXD */
+ ste,config = <&in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO30_W3"; /* TXD */
+ ste,config = <&out_wkup_pdis>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index aa3f02060fdd..914a5f4399e5 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include "ste-dbx5x0.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
/ {
memory {
@@ -30,14 +31,23 @@
soc {
uart at 80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart0_default_mode>;
+ pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
uart at 80121000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_default_mode>;
+ pinctrl-1 = <&uart1_sleep_mode>;
status = "okay";
};
uart at 80007000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart2_default_mode>;
+ pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index f0b39f835914..16d28863ef6e 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "ste-dbx5x0.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
/ {
model = "Calao Systems Snowball platform with device tree";
@@ -155,14 +156,23 @@
};
uart at 80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart0_default_mode>;
+ pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
uart at 80121000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_default_mode>;
+ pinctrl-1 = <&uart1_sleep_mode>;
status = "okay";
};
uart at 80007000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart2_default_mode>;
+ pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 0efb1560fc35..c6225191141f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -65,16 +65,12 @@ BIAS(slpm_in_nopull_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(slpm_out_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(in_wkup_pdis_en, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
PIN_SLPM_PDIS_ENABLED);
BIAS(in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
PIN_SLPM_PDIS_DISABLED);
-BIAS(out_wkup_pdis, PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_DISABLED);
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
@@ -376,50 +372,10 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
*/
DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
/*
- * UART0, we do not mux in u0 here.
- * uart-0 pins gpio configuration should be kept intact to prevent
- * a glitch in tx line when the tty dev is opened. Later these pins
- * are configured by uart driver
- */
- DB8500_PIN_HOG("GPIO0_AJ5", in_pu), /* CTS */
- DB8500_PIN_HOG("GPIO1_AJ3", out_hi), /* RTS */
- DB8500_PIN_HOG("GPIO2_AH4", in_pu), /* RXD */
- DB8500_PIN_HOG("GPIO3_AH3", out_hi), /* TXD */
- /*
- * Mux in UART2 on altfunction C and set pull-ups.
- * TODO: is this used on U8500 variants and Snowball really?
- * The setting on GPIO31 conflicts with magnetometer use on hrefv60
- */
- /* default state for UART2 */
- DB8500_MUX("u2rxtx_c_1", "u2", "uart2"),
- DB8500_PIN("GPIO29_W2", in_pu, "uart2"), /* RXD */
- DB8500_PIN("GPIO30_W3", out_hi, "uart2"), /* TXD */
- /* Sleep state for UART2 */
- DB8500_PIN_SLEEP("GPIO29_W2", in_wkup_pdis, "uart2"),
- DB8500_PIN_SLEEP("GPIO30_W3", out_wkup_pdis, "uart2"),
- /*
* The following pin sets were known as "runtime pins" before being
* converted to the pinctrl model. Here we model them as "default"
* states.
*/
- /* Mux in UART0 after initialization */
- DB8500_MUX("u0_a_1", "u0", "uart0"),
- DB8500_PIN("GPIO0_AJ5", in_pu, "uart0"), /* CTS */
- DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
- DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
- DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
- /* Sleep state for UART0 */
- DB8500_PIN_SLEEP("GPIO0_AJ5", slpm_in_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO1_AJ3", slpm_out_hi_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO2_AH4", slpm_in_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO3_AH3", slpm_out_wkup_pdis, "uart0"),
- /* Mux in UART1 after initialization */
- DB8500_MUX("u1rxtx_a_1", "u1", "uart1"),
- DB8500_PIN("GPIO4_AH6", in_pu, "uart1"), /* RXD */
- DB8500_PIN("GPIO5_AG6", out_hi, "uart1"), /* TXD */
- /* Sleep state for UART1 */
- DB8500_PIN_SLEEP("GPIO4_AH6", slpm_in_wkup_pdis, "uart1"),
- DB8500_PIN_SLEEP("GPIO5_AG6", slpm_out_wkup_pdis, "uart1"),
/* MSP1 for ALSA codec */
DB8500_MUX_HOG("msp1txrx_a_1", "msp1"),
DB8500_MUX_HOG("msp1_a_1", "msp1"),
@@ -822,10 +778,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
DB8500_PIN_HOG("GPIO7_AG5", in_pu),
/* TC35892 IRQ, pull up the line, let the driver mux in the pin */
DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
- /* Mux in UART1 and set the pull-ups */
- DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
- DB8500_PIN_HOG("GPIO4_AH6", in_pu), /* RXD */
- DB8500_PIN_HOG("GPIO5_AG6", out_hi), /* TXD */
/*
* Runtime stuff: make it possible to mux in the SKE keypad
* and bias the pins
@@ -971,10 +923,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
};
static struct pinctrl_map __initdata u9500_pinmap[] = {
- /* Mux in UART1 (just RX/TX) and set the pull-ups */
- DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
- DB8500_PIN_HOG("GPIO4_AH6", in_pu),
- DB8500_PIN_HOG("GPIO5_AG6", out_hi),
/* WLAN_IRQ line */
DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu),
/* HSI */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 02/21] ARM: ux500: move I2C pin control to the device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij, Patrice Chotard
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.
Cc: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Patrice Chotard <patrice.chotard-qxv4g6HH51o@public.gmane.org>
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 105 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 21 +++++
arch/arm/boot/dts/ste-snowball.dts | 24 ++++++
arch/arm/mach-ux500/board-mop500-pins.c | 22 ------
4 files changed, 150 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index d979de27b6e1..d2e63f3fb687 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -109,6 +109,111 @@
};
};
};
+
+ /* Settings for all I2C default and sleep states */
+ i2c0 {
+ i2c0_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c0";
+ ste,pins = "i2c0_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c0_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c1 {
+ i2c1_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c1";
+ ste,pins = "i2c1_b_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c1_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c2 {
+ i2c2_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c2";
+ ste,pins = "i2c2_b_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c2_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c3 {
+ i2c3_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c3";
+ ste,pins = "i2c3_c_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c3_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ /*
+ * Activating I2C4 will conflict with UART1 about the same pins so do not
+ * enable I2C4 and UART1 at the same time.
+ */
+ i2c4 {
+ i2c4_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c4";
+ ste,pins = "i2c4_b_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c4_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 914a5f4399e5..1863241c911e 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -51,7 +51,22 @@
status = "okay";
};
+ i2c@80004000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c0_default_mode>;
+ pinctrl-1 = <&i2c0_sleep_mode>;
+ };
+
+ i2c@80122000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c1_default_mode>;
+ pinctrl-1 = <&i2c1_sleep_mode>;
+ };
+
i2c@80128000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c2_default_mode>;
+ pinctrl-1 = <&i2c2_sleep_mode>;
lp5521@33 {
compatible = "national,lp5521";
reg = <0x33>;
@@ -95,6 +110,12 @@
};
};
+ i2c@80110000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c3_default_mode>;
+ pinctrl-1 = <&i2c3_sleep_mode>;
+ };
+
// External Micro SD slot
sdi0_per1@80126000 {
arm,primecell-periphid = <0x10480180>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 16d28863ef6e..f8df43e0791d 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -176,6 +176,30 @@
status = "okay";
};
+ i2c@80004000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c0_default_mode>;
+ pinctrl-1 = <&i2c0_sleep_mode>;
+ };
+
+ i2c@80122000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c1_default_mode>;
+ pinctrl-1 = <&i2c1_sleep_mode>;
+ };
+
+ i2c@80128000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c2_default_mode>;
+ pinctrl-1 = <&i2c2_sleep_mode>;
+ };
+
+ i2c@80110000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c3_default_mode>;
+ pinctrl-1 = <&i2c3_sleep_mode>;
+ };
+
cpufreq-cooling {
status = "okay";
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index c6225191141f..1f1e53972063 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -61,8 +61,6 @@ BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_nopull_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
@@ -391,26 +389,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in i2c0 block, default state */
- DB8500_MUX("i2c0_a_1", "i2c0", "nmk-i2c.0"),
- /* i2c0 sleep state */
- DB8500_PIN_SLEEP("GPIO147_C15", slpm_in_nopull_wkup_pdis, "nmk-i2c.0"), /* SDA */
- DB8500_PIN_SLEEP("GPIO148_B16", slpm_in_nopull_wkup_pdis, "nmk-i2c.0"), /* SCL */
- /* Mux in i2c1 block, default state */
- DB8500_MUX("i2c1_b_2", "i2c1", "nmk-i2c.1"),
- /* i2c1 sleep state */
- DB8500_PIN_SLEEP("GPIO16_AD3", slpm_in_nopull_wkup_pdis, "nmk-i2c.1"), /* SDA */
- DB8500_PIN_SLEEP("GPIO17_AD4", slpm_in_nopull_wkup_pdis, "nmk-i2c.1"), /* SCL */
- /* Mux in i2c2 block, default state */
- DB8500_MUX("i2c2_b_2", "i2c2", "nmk-i2c.2"),
- /* i2c2 sleep state */
- DB8500_PIN_SLEEP("GPIO10_AF5", slpm_in_nopull_wkup_pdis, "nmk-i2c.2"), /* SDA */
- DB8500_PIN_SLEEP("GPIO11_AG4", slpm_in_nopull_wkup_pdis, "nmk-i2c.2"), /* SCL */
- /* Mux in i2c3 block, default state */
- DB8500_MUX("i2c3_c_2", "i2c3", "nmk-i2c.3"),
- /* i2c3 sleep state */
- DB8500_PIN_SLEEP("GPIO229_AG7", slpm_in_nopull_wkup_pdis, "nmk-i2c.3"), /* SDA */
- DB8500_PIN_SLEEP("GPIO230_AF7", slpm_in_nopull_wkup_pdis, "nmk-i2c.3"), /* SCL */
/* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 02/21] ARM: ux500: move I2C pin control to the device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 105 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 21 +++++
arch/arm/boot/dts/ste-snowball.dts | 24 ++++++
arch/arm/mach-ux500/board-mop500-pins.c | 22 ------
4 files changed, 150 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index d979de27b6e1..d2e63f3fb687 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -109,6 +109,111 @@
};
};
};
+
+ /* Settings for all I2C default and sleep states */
+ i2c0 {
+ i2c0_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c0";
+ ste,pins = "i2c0_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c0_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c1 {
+ i2c1_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c1";
+ ste,pins = "i2c1_b_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c1_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c2 {
+ i2c2_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c2";
+ ste,pins = "i2c2_b_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c2_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c3 {
+ i2c3_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c3";
+ ste,pins = "i2c3_c_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c3_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ /*
+ * Activating I2C4 will conflict with UART1 about the same pins so do not
+ * enable I2C4 and UART1 at the same time.
+ */
+ i2c4 {
+ i2c4_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c4";
+ ste,pins = "i2c4_b_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c4_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 914a5f4399e5..1863241c911e 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -51,7 +51,22 @@
status = "okay";
};
+ i2c at 80004000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c0_default_mode>;
+ pinctrl-1 = <&i2c0_sleep_mode>;
+ };
+
+ i2c at 80122000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c1_default_mode>;
+ pinctrl-1 = <&i2c1_sleep_mode>;
+ };
+
i2c at 80128000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c2_default_mode>;
+ pinctrl-1 = <&i2c2_sleep_mode>;
lp5521 at 33 {
compatible = "national,lp5521";
reg = <0x33>;
@@ -95,6 +110,12 @@
};
};
+ i2c at 80110000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c3_default_mode>;
+ pinctrl-1 = <&i2c3_sleep_mode>;
+ };
+
// External Micro SD slot
sdi0_per1 at 80126000 {
arm,primecell-periphid = <0x10480180>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 16d28863ef6e..f8df43e0791d 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -176,6 +176,30 @@
status = "okay";
};
+ i2c at 80004000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c0_default_mode>;
+ pinctrl-1 = <&i2c0_sleep_mode>;
+ };
+
+ i2c at 80122000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c1_default_mode>;
+ pinctrl-1 = <&i2c1_sleep_mode>;
+ };
+
+ i2c at 80128000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c2_default_mode>;
+ pinctrl-1 = <&i2c2_sleep_mode>;
+ };
+
+ i2c at 80110000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c3_default_mode>;
+ pinctrl-1 = <&i2c3_sleep_mode>;
+ };
+
cpufreq-cooling {
status = "okay";
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index c6225191141f..1f1e53972063 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -61,8 +61,6 @@ BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_nopull_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
@@ -391,26 +389,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in i2c0 block, default state */
- DB8500_MUX("i2c0_a_1", "i2c0", "nmk-i2c.0"),
- /* i2c0 sleep state */
- DB8500_PIN_SLEEP("GPIO147_C15", slpm_in_nopull_wkup_pdis, "nmk-i2c.0"), /* SDA */
- DB8500_PIN_SLEEP("GPIO148_B16", slpm_in_nopull_wkup_pdis, "nmk-i2c.0"), /* SCL */
- /* Mux in i2c1 block, default state */
- DB8500_MUX("i2c1_b_2", "i2c1", "nmk-i2c.1"),
- /* i2c1 sleep state */
- DB8500_PIN_SLEEP("GPIO16_AD3", slpm_in_nopull_wkup_pdis, "nmk-i2c.1"), /* SDA */
- DB8500_PIN_SLEEP("GPIO17_AD4", slpm_in_nopull_wkup_pdis, "nmk-i2c.1"), /* SCL */
- /* Mux in i2c2 block, default state */
- DB8500_MUX("i2c2_b_2", "i2c2", "nmk-i2c.2"),
- /* i2c2 sleep state */
- DB8500_PIN_SLEEP("GPIO10_AF5", slpm_in_nopull_wkup_pdis, "nmk-i2c.2"), /* SDA */
- DB8500_PIN_SLEEP("GPIO11_AG4", slpm_in_nopull_wkup_pdis, "nmk-i2c.2"), /* SCL */
- /* Mux in i2c3 block, default state */
- DB8500_MUX("i2c3_c_2", "i2c3", "nmk-i2c.3"),
- /* i2c3 sleep state */
- DB8500_PIN_SLEEP("GPIO229_AG7", slpm_in_nopull_wkup_pdis, "nmk-i2c.3"), /* SDA */
- DB8500_PIN_SLEEP("GPIO230_AF7", slpm_in_nopull_wkup_pdis, "nmk-i2c.3"), /* SCL */
/* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 03/21] ARM: ux500: move MMC/SD/SDIO pin control to the device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij, Patrice Chotard
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Patrice Chotard <patrice.chotard-qxv4g6HH51o@public.gmane.org>
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 211 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 12 ++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 17 ++
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 12 ++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 19 +++
arch/arm/boot/dts/ste-snowball.dts | 43 +++++
arch/arm/mach-ux500/board-mop500-pins.c | 107 -------------
7 files changed, 314 insertions(+), 107 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index d2e63f3fb687..23583b0546d9 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -214,6 +214,217 @@
};
};
};
+
+ /* Settings for all MMC/SD/SDIO default and sleep states */
+ sdi0 {
+ /* This is the external SD card slot, 4 bits wide */
+ sdi0_default_mode: sdi0_default {
+ default_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO18_AC2", /* CMDDIR */
+ "GPIO19_AC1", /* DAT0DIR */
+ "GPIO20_AB4"; /* DAT2DIR */
+ ste,config = <&out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO22_AA3"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins = "GPIO23_AA4"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg4 {
+ ste,pins =
+ "GPIO24_AB2", /* CMD */
+ "GPIO25_Y4", /* DAT0 */
+ "GPIO26_Y2", /* DAT1 */
+ "GPIO27_AA2", /* DAT2 */
+ "GPIO28_AA1"; /* DAT3 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi0_sleep_mode: sdi0_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO18_AC2", /* CMDDIR */
+ "GPIO19_AC1", /* DAT0DIR */
+ "GPIO20_AB4"; /* DAT2DIR */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO22_AA3", /* FBCLK */
+ "GPIO24_AB2", /* CMD */
+ "GPIO25_Y4", /* DAT0 */
+ "GPIO26_Y2", /* DAT1 */
+ "GPIO27_AA2", /* DAT2 */
+ "GPIO28_AA1"; /* DAT3 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO23_AA4"; /* CLK */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi1 {
+ /* This is the WLAN SDIO 4 bits wide */
+ sdi1_default_mode: sdi1_default {
+ default_mux {
+ ste,function = "mc1";
+ ste,pins = "mc1_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO208_AH16"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO209_AG15"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO210_AJ15", /* CMD */
+ "GPIO211_AG14", /* DAT0 */
+ "GPIO212_AF13", /* DAT1 */
+ "GPIO213_AG13", /* DAT2 */
+ "GPIO214_AH15"; /* DAT3 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi1_sleep_mode: sdi1_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO208_AH16"; /* CLK */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO209_AG15", /* FBCLK */
+ "GPIO210_AJ15", /* CMD */
+ "GPIO211_AG14", /* DAT0 */
+ "GPIO212_AF13", /* DAT1 */
+ "GPIO213_AG13", /* DAT2 */
+ "GPIO214_AH15"; /* DAT3 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi2 {
+ /* This is the eMMC 8 bits wide, usually PoP eMMC */
+ sdi2_default_mode: sdi2_default {
+ default_mux {
+ ste,function = "mc2";
+ ste,pins = "mc2_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO128_A5"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO130_C8"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO129_B4", /* CMD */
+ "GPIO131_A12", /* DAT0 */
+ "GPIO132_C10", /* DAT1 */
+ "GPIO133_B10", /* DAT2 */
+ "GPIO134_B9", /* DAT3 */
+ "GPIO135_A9", /* DAT4 */
+ "GPIO136_C7", /* DAT5 */
+ "GPIO137_A7", /* DAT6 */
+ "GPIO138_C5"; /* DAT7 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi2_sleep_mode: sdi2_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO128_A5"; /* CLK */
+ ste,config = <&out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO130_C8", /* FBCLK */
+ "GPIO129_B4"; /* CMD */
+ ste,config = <&in_wkup_pdis_en>;
+ };
+ sleep_cfg3 {
+ ste,pins =
+ "GPIO131_A12", /* DAT0 */
+ "GPIO132_C10", /* DAT1 */
+ "GPIO133_B10", /* DAT2 */
+ "GPIO134_B9", /* DAT3 */
+ "GPIO135_A9", /* DAT4 */
+ "GPIO136_C7", /* DAT5 */
+ "GPIO137_A7", /* DAT6 */
+ "GPIO138_C5"; /* DAT7 */
+ ste,config = <&in_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi4 {
+ /* This is the eMMC 8 bits wide, usually PCB-mounted eMMC */
+ sdi4_default_mode: sdi4_default {
+ default_mux {
+ ste,function = "mc4";
+ ste,pins = "mc4_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO203_AE23"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO202_AF25"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO201_AF24", /* CMD */
+ "GPIO200_AH26", /* DAT0 */
+ "GPIO199_AH23", /* DAT1 */
+ "GPIO198_AG25", /* DAT2 */
+ "GPIO197_AH24", /* DAT3 */
+ "GPIO207_AJ23", /* DAT4 */
+ "GPIO206_AG24", /* DAT5 */
+ "GPIO205_AG23", /* DAT6 */
+ "GPIO204_AF23"; /* DAT7 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi4_sleep_mode: sdi4_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO203_AE23"; /* CLK */
+ ste,config = <&out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO202_AF25", /* FBCLK */
+ "GPIO201_AF24", /* CMD */
+ "GPIO200_AH26", /* DAT0 */
+ "GPIO199_AH23", /* DAT1 */
+ "GPIO198_AG25", /* DAT2 */
+ "GPIO197_AH24", /* DAT3 */
+ "GPIO207_AJ23", /* DAT4 */
+ "GPIO206_AG24", /* DAT5 */
+ "GPIO205_AG23", /* DAT6 */
+ "GPIO204_AF23"; /* DAT7 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 1863241c911e..845eb25f5d26 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -125,6 +125,9 @@
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi0_default_mode>;
+ pinctrl-1 = <&sdi0_sleep_mode>;
cd-gpios = <&tc3589x_gpio 3 0x4>;
@@ -136,6 +139,9 @@
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi1_default_mode>;
+ pinctrl-1 = <&sdi1_sleep_mode>;
status = "okay";
};
@@ -146,6 +152,9 @@
max-frequency = <100000000>;
bus-width = <8>;
mmc-cap-mmc-highspeed;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi2_default_mode>;
+ pinctrl-1 = <&sdi2_sleep_mode>;
status = "okay";
};
@@ -157,6 +166,9 @@
bus-width = <8>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi4_default_mode>;
+ pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 6b271a410d03..cfd7ef306d49 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -55,5 +55,22 @@
status = "okay";
};
+
+ pinctrl {
+ sdi0 {
+ /* This additional pin needed on early MOP500 and HREFs previous to v60 */
+ sdi0_default_mode: sdi0_default {
+ hrefprev60_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0dat31dir_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO21_AB3"; /* DAT31DIR */
+ ste,config = <&out_hi>;
+ };
+
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index aed511b47a9e..452f00c4f7c0 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -66,5 +66,17 @@
status = "okay";
};
+
+ pinctrl {
+ sdi0 {
+ /* SD card detect GPIO pin, extend default state */
+ sdi0_default_mode: sdi0_default {
+ default_hrefv60_cfg1 {
+ ste,pins = "GPIO95_E8";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index efddee9403c4..f213222cf220 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -68,6 +68,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_out_wkup_pdis: slpm_out_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_DIR_OUTPUT>;
@@ -81,6 +88,18 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ in_wkup_pdis_en: in_wkup_pdis_en {
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
+ out_lo_wkup_pdis: out_lo_wkup_pdis {
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
out_hi_wkup_pdis: out_hi_wkup_pdis {
ste,sleep-output = <SLPM_OUTPUT_HIGH>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index f8df43e0791d..c2cb3ea637dc 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -137,6 +137,9 @@
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi0_default_mode>;
+ pinctrl-1 = <&sdi0_sleep_mode>;
cd-gpios = <&gpio6 26 0x4>; // 218
cd-inverted;
@@ -144,6 +147,27 @@
status = "okay";
};
+ // WLAN SDIO channel
+ sdi1_per2@80118000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi1_default_mode>;
+ pinctrl-1 = <&sdi1_sleep_mode>;
+
+ status = "okay";
+ };
+
+ // Unused PoP eMMC - register and put it to sleep by default */
+ sdi2_per3@80005000 {
+ arm,primecell-periphid = <0x10480180>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdi2_sleep_mode>;
+
+ status = "okay";
+ };
+
// On-board eMMC
sdi4_per2@80114000 {
arm,primecell-periphid = <0x10480180>;
@@ -151,6 +175,9 @@
bus-width = <8>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi4_default_mode>;
+ pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
@@ -300,5 +327,21 @@
};
};
};
+
+ pinctrl {
+ sdi0 {
+ sdi0_default_mode: sdi0_default {
+ snowball_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0dat31dir_a_1";
+ };
+ snowball_cfg1 {
+ ste,pins = "GPIO21_AB3"; /* DAT31DIR */
+ ste,config = <&out_hi>;
+ };
+
+ };
+ };
+ };
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 1f1e53972063..0f9a0776cf90 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -63,12 +63,6 @@ BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(in_wkup_pdis_en, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_ENABLED);
-BIAS(in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_DISABLED);
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
@@ -389,99 +383,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
- DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
- DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
- DB8500_PIN("GPIO19_AC1", out_hi, "sdi0"), /* DAT0DIR */
- DB8500_PIN("GPIO20_AB4", out_hi, "sdi0"), /* DAT2DIR */
- DB8500_PIN("GPIO22_AA3", in_nopull, "sdi0"), /* FBCLK */
- DB8500_PIN("GPIO23_AA4", out_lo, "sdi0"), /* CLK */
- DB8500_PIN("GPIO24_AB2", in_pu, "sdi0"), /* CMD */
- DB8500_PIN("GPIO25_Y4", in_pu, "sdi0"), /* DAT0 */
- DB8500_PIN("GPIO26_Y2", in_pu, "sdi0"), /* DAT1 */
- DB8500_PIN("GPIO27_AA2", in_pu, "sdi0"), /* DAT2 */
- DB8500_PIN("GPIO28_AA1", in_pu, "sdi0"), /* DAT3 */
- /* SDI0 sleep state */
- DB8500_PIN_SLEEP("GPIO18_AC2", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO19_AC1", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO20_AB4", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO22_AA3", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO23_AA4", slpm_out_lo_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO24_AB2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO25_Y4", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO26_Y2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO27_AA2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO28_AA1", slpm_in_wkup_pdis, "sdi0"),
-
- /* Mux in SDI1 (here called MC1) used for SDIO for CW1200 WLAN */
- DB8500_MUX("mc1_a_1", "mc1", "sdi1"),
- DB8500_PIN("GPIO208_AH16", out_lo, "sdi1"), /* CLK */
- DB8500_PIN("GPIO209_AG15", in_nopull, "sdi1"), /* FBCLK */
- DB8500_PIN("GPIO210_AJ15", in_pu, "sdi1"), /* CMD */
- DB8500_PIN("GPIO211_AG14", in_pu, "sdi1"), /* DAT0 */
- DB8500_PIN("GPIO212_AF13", in_pu, "sdi1"), /* DAT1 */
- DB8500_PIN("GPIO213_AG13", in_pu, "sdi1"), /* DAT2 */
- DB8500_PIN("GPIO214_AH15", in_pu, "sdi1"), /* DAT3 */
- /* SDI1 sleep state */
- DB8500_PIN_SLEEP("GPIO208_AH16", slpm_out_lo_wkup_pdis, "sdi1"), /* CLK */
- DB8500_PIN_SLEEP("GPIO209_AG15", slpm_in_wkup_pdis, "sdi1"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO210_AJ15", slpm_in_wkup_pdis, "sdi1"), /* CMD */
- DB8500_PIN_SLEEP("GPIO211_AG14", slpm_in_wkup_pdis, "sdi1"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO212_AF13", slpm_in_wkup_pdis, "sdi1"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO213_AG13", slpm_in_wkup_pdis, "sdi1"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO214_AH15", slpm_in_wkup_pdis, "sdi1"), /* DAT3 */
-
- /* Mux in SDI2 (here called MC2) used for for PoP eMMC */
- DB8500_MUX("mc2_a_1", "mc2", "sdi2"),
- DB8500_PIN("GPIO128_A5", out_lo, "sdi2"), /* CLK */
- DB8500_PIN("GPIO129_B4", in_pu, "sdi2"), /* CMD */
- DB8500_PIN("GPIO130_C8", in_nopull, "sdi2"), /* FBCLK */
- DB8500_PIN("GPIO131_A12", in_pu, "sdi2"), /* DAT0 */
- DB8500_PIN("GPIO132_C10", in_pu, "sdi2"), /* DAT1 */
- DB8500_PIN("GPIO133_B10", in_pu, "sdi2"), /* DAT2 */
- DB8500_PIN("GPIO134_B9", in_pu, "sdi2"), /* DAT3 */
- DB8500_PIN("GPIO135_A9", in_pu, "sdi2"), /* DAT4 */
- DB8500_PIN("GPIO136_C7", in_pu, "sdi2"), /* DAT5 */
- DB8500_PIN("GPIO137_A7", in_pu, "sdi2"), /* DAT6 */
- DB8500_PIN("GPIO138_C5", in_pu, "sdi2"), /* DAT7 */
- /* SDI2 sleep state */
- DB8500_PIN_SLEEP("GPIO128_A5", out_lo_wkup_pdis, "sdi2"), /* CLK */
- DB8500_PIN_SLEEP("GPIO129_B4", in_wkup_pdis_en, "sdi2"), /* CMD */
- DB8500_PIN_SLEEP("GPIO130_C8", in_wkup_pdis_en, "sdi2"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO131_A12", in_wkup_pdis, "sdi2"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO132_C10", in_wkup_pdis, "sdi2"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO133_B10", in_wkup_pdis, "sdi2"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO134_B9", in_wkup_pdis, "sdi2"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO135_A9", in_wkup_pdis, "sdi2"), /* DAT4 */
- DB8500_PIN_SLEEP("GPIO136_C7", in_wkup_pdis, "sdi2"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO137_A7", in_wkup_pdis, "sdi2"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO138_C5", in_wkup_pdis, "sdi2"), /* DAT7 */
-
- /* Mux in SDI4 (here called MC4) used for for PCB-mounted eMMC */
- DB8500_MUX("mc4_a_1", "mc4", "sdi4"),
- DB8500_PIN("GPIO197_AH24", in_pu, "sdi4"), /* DAT3 */
- DB8500_PIN("GPIO198_AG25", in_pu, "sdi4"), /* DAT2 */
- DB8500_PIN("GPIO199_AH23", in_pu, "sdi4"), /* DAT1 */
- DB8500_PIN("GPIO200_AH26", in_pu, "sdi4"), /* DAT0 */
- DB8500_PIN("GPIO201_AF24", in_pu, "sdi4"), /* CMD */
- DB8500_PIN("GPIO202_AF25", in_nopull, "sdi4"), /* FBCLK */
- DB8500_PIN("GPIO203_AE23", out_lo, "sdi4"), /* CLK */
- DB8500_PIN("GPIO204_AF23", in_pu, "sdi4"), /* DAT7 */
- DB8500_PIN("GPIO205_AG23", in_pu, "sdi4"), /* DAT6 */
- DB8500_PIN("GPIO206_AG24", in_pu, "sdi4"), /* DAT5 */
- DB8500_PIN("GPIO207_AJ23", in_pu, "sdi4"), /* DAT4 */
- /*SDI4 sleep state */
- DB8500_PIN_SLEEP("GPIO197_AH24", slpm_in_wkup_pdis, "sdi4"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO198_AG25", slpm_in_wkup_pdis, "sdi4"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO199_AH23", slpm_in_wkup_pdis, "sdi4"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO200_AH26", slpm_in_wkup_pdis, "sdi4"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO201_AF24", slpm_in_wkup_pdis, "sdi4"), /* CMD */
- DB8500_PIN_SLEEP("GPIO202_AF25", slpm_in_wkup_pdis, "sdi4"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO203_AE23", slpm_out_lo_wkup_pdis, "sdi4"), /* CLK */
- DB8500_PIN_SLEEP("GPIO204_AF23", slpm_in_wkup_pdis, "sdi4"), /* DAT7 */
- DB8500_PIN_SLEEP("GPIO205_AG23", slpm_in_wkup_pdis, "sdi4"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO206_AG24", slpm_in_wkup_pdis, "sdi4"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO207_AJ23", slpm_in_wkup_pdis, "sdi4"), /* DAT4 */
/* Mux in USB pins, drive STP high */
/* USB default state */
@@ -795,10 +696,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
-
- /* Mux in and drive the SDI0 DAT31DIR line high at runtime */
- DB8500_MUX("mc0dat31dir_a_1", "mc0", "sdi0"),
- DB8500_PIN("GPIO21_AB3", out_hi, "sdi0"),
};
/*
@@ -888,8 +785,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
/* Accelerometer interrupt lines */
DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
- /* SD card detect GPIO pin */
- DB8500_PIN_HOG("GPIO95_E8", gpio_in_pu),
/*
* Runtime stuff
* Pull up/down of some sensor GPIO pins, for proximity, HAL sensor
@@ -925,8 +820,6 @@ static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
DB8500_PIN_HOG("GPIO145_C13", pd),
- /* Always drive the MC0 DAT31DIR line high on these boards */
- DB8500_PIN_HOG("GPIO21_AB3", out_hi),
/* Mux in "SM" which is used for the SMSC911x Ethernet adapter */
DB8500_MUX_HOG("sm_b_1", "sm"),
/* User LED */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 03/21] ARM: ux500: move MMC/SD/SDIO pin control to the device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 211 +++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 12 ++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 17 ++
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 12 ++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 19 +++
arch/arm/boot/dts/ste-snowball.dts | 43 +++++
arch/arm/mach-ux500/board-mop500-pins.c | 107 -------------
7 files changed, 314 insertions(+), 107 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index d2e63f3fb687..23583b0546d9 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -214,6 +214,217 @@
};
};
};
+
+ /* Settings for all MMC/SD/SDIO default and sleep states */
+ sdi0 {
+ /* This is the external SD card slot, 4 bits wide */
+ sdi0_default_mode: sdi0_default {
+ default_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO18_AC2", /* CMDDIR */
+ "GPIO19_AC1", /* DAT0DIR */
+ "GPIO20_AB4"; /* DAT2DIR */
+ ste,config = <&out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO22_AA3"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins = "GPIO23_AA4"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg4 {
+ ste,pins =
+ "GPIO24_AB2", /* CMD */
+ "GPIO25_Y4", /* DAT0 */
+ "GPIO26_Y2", /* DAT1 */
+ "GPIO27_AA2", /* DAT2 */
+ "GPIO28_AA1"; /* DAT3 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi0_sleep_mode: sdi0_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO18_AC2", /* CMDDIR */
+ "GPIO19_AC1", /* DAT0DIR */
+ "GPIO20_AB4"; /* DAT2DIR */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO22_AA3", /* FBCLK */
+ "GPIO24_AB2", /* CMD */
+ "GPIO25_Y4", /* DAT0 */
+ "GPIO26_Y2", /* DAT1 */
+ "GPIO27_AA2", /* DAT2 */
+ "GPIO28_AA1"; /* DAT3 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO23_AA4"; /* CLK */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi1 {
+ /* This is the WLAN SDIO 4 bits wide */
+ sdi1_default_mode: sdi1_default {
+ default_mux {
+ ste,function = "mc1";
+ ste,pins = "mc1_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO208_AH16"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO209_AG15"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO210_AJ15", /* CMD */
+ "GPIO211_AG14", /* DAT0 */
+ "GPIO212_AF13", /* DAT1 */
+ "GPIO213_AG13", /* DAT2 */
+ "GPIO214_AH15"; /* DAT3 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi1_sleep_mode: sdi1_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO208_AH16"; /* CLK */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO209_AG15", /* FBCLK */
+ "GPIO210_AJ15", /* CMD */
+ "GPIO211_AG14", /* DAT0 */
+ "GPIO212_AF13", /* DAT1 */
+ "GPIO213_AG13", /* DAT2 */
+ "GPIO214_AH15"; /* DAT3 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi2 {
+ /* This is the eMMC 8 bits wide, usually PoP eMMC */
+ sdi2_default_mode: sdi2_default {
+ default_mux {
+ ste,function = "mc2";
+ ste,pins = "mc2_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO128_A5"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO130_C8"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO129_B4", /* CMD */
+ "GPIO131_A12", /* DAT0 */
+ "GPIO132_C10", /* DAT1 */
+ "GPIO133_B10", /* DAT2 */
+ "GPIO134_B9", /* DAT3 */
+ "GPIO135_A9", /* DAT4 */
+ "GPIO136_C7", /* DAT5 */
+ "GPIO137_A7", /* DAT6 */
+ "GPIO138_C5"; /* DAT7 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi2_sleep_mode: sdi2_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO128_A5"; /* CLK */
+ ste,config = <&out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO130_C8", /* FBCLK */
+ "GPIO129_B4"; /* CMD */
+ ste,config = <&in_wkup_pdis_en>;
+ };
+ sleep_cfg3 {
+ ste,pins =
+ "GPIO131_A12", /* DAT0 */
+ "GPIO132_C10", /* DAT1 */
+ "GPIO133_B10", /* DAT2 */
+ "GPIO134_B9", /* DAT3 */
+ "GPIO135_A9", /* DAT4 */
+ "GPIO136_C7", /* DAT5 */
+ "GPIO137_A7", /* DAT6 */
+ "GPIO138_C5"; /* DAT7 */
+ ste,config = <&in_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi4 {
+ /* This is the eMMC 8 bits wide, usually PCB-mounted eMMC */
+ sdi4_default_mode: sdi4_default {
+ default_mux {
+ ste,function = "mc4";
+ ste,pins = "mc4_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO203_AE23"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO202_AF25"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO201_AF24", /* CMD */
+ "GPIO200_AH26", /* DAT0 */
+ "GPIO199_AH23", /* DAT1 */
+ "GPIO198_AG25", /* DAT2 */
+ "GPIO197_AH24", /* DAT3 */
+ "GPIO207_AJ23", /* DAT4 */
+ "GPIO206_AG24", /* DAT5 */
+ "GPIO205_AG23", /* DAT6 */
+ "GPIO204_AF23"; /* DAT7 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi4_sleep_mode: sdi4_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO203_AE23"; /* CLK */
+ ste,config = <&out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO202_AF25", /* FBCLK */
+ "GPIO201_AF24", /* CMD */
+ "GPIO200_AH26", /* DAT0 */
+ "GPIO199_AH23", /* DAT1 */
+ "GPIO198_AG25", /* DAT2 */
+ "GPIO197_AH24", /* DAT3 */
+ "GPIO207_AJ23", /* DAT4 */
+ "GPIO206_AG24", /* DAT5 */
+ "GPIO205_AG23", /* DAT6 */
+ "GPIO204_AF23"; /* DAT7 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 1863241c911e..845eb25f5d26 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -125,6 +125,9 @@
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi0_default_mode>;
+ pinctrl-1 = <&sdi0_sleep_mode>;
cd-gpios = <&tc3589x_gpio 3 0x4>;
@@ -136,6 +139,9 @@
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi1_default_mode>;
+ pinctrl-1 = <&sdi1_sleep_mode>;
status = "okay";
};
@@ -146,6 +152,9 @@
max-frequency = <100000000>;
bus-width = <8>;
mmc-cap-mmc-highspeed;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi2_default_mode>;
+ pinctrl-1 = <&sdi2_sleep_mode>;
status = "okay";
};
@@ -157,6 +166,9 @@
bus-width = <8>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi4_default_mode>;
+ pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 6b271a410d03..cfd7ef306d49 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -55,5 +55,22 @@
status = "okay";
};
+
+ pinctrl {
+ sdi0 {
+ /* This additional pin needed on early MOP500 and HREFs previous to v60 */
+ sdi0_default_mode: sdi0_default {
+ hrefprev60_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0dat31dir_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO21_AB3"; /* DAT31DIR */
+ ste,config = <&out_hi>;
+ };
+
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index aed511b47a9e..452f00c4f7c0 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -66,5 +66,17 @@
status = "okay";
};
+
+ pinctrl {
+ sdi0 {
+ /* SD card detect GPIO pin, extend default state */
+ sdi0_default_mode: sdi0_default {
+ default_hrefv60_cfg1 {
+ ste,pins = "GPIO95_E8";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index efddee9403c4..f213222cf220 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -68,6 +68,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_out_wkup_pdis: slpm_out_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_DIR_OUTPUT>;
@@ -81,6 +88,18 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ in_wkup_pdis_en: in_wkup_pdis_en {
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
+ out_lo_wkup_pdis: out_lo_wkup_pdis {
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
out_hi_wkup_pdis: out_hi_wkup_pdis {
ste,sleep-output = <SLPM_OUTPUT_HIGH>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index f8df43e0791d..c2cb3ea637dc 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -137,6 +137,9 @@
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi0_default_mode>;
+ pinctrl-1 = <&sdi0_sleep_mode>;
cd-gpios = <&gpio6 26 0x4>; // 218
cd-inverted;
@@ -144,6 +147,27 @@
status = "okay";
};
+ // WLAN SDIO channel
+ sdi1_per2 at 80118000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi1_default_mode>;
+ pinctrl-1 = <&sdi1_sleep_mode>;
+
+ status = "okay";
+ };
+
+ // Unused PoP eMMC - register and put it to sleep by default */
+ sdi2_per3 at 80005000 {
+ arm,primecell-periphid = <0x10480180>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdi2_sleep_mode>;
+
+ status = "okay";
+ };
+
// On-board eMMC
sdi4_per2 at 80114000 {
arm,primecell-periphid = <0x10480180>;
@@ -151,6 +175,9 @@
bus-width = <8>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi4_default_mode>;
+ pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
@@ -300,5 +327,21 @@
};
};
};
+
+ pinctrl {
+ sdi0 {
+ sdi0_default_mode: sdi0_default {
+ snowball_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0dat31dir_a_1";
+ };
+ snowball_cfg1 {
+ ste,pins = "GPIO21_AB3"; /* DAT31DIR */
+ ste,config = <&out_hi>;
+ };
+
+ };
+ };
+ };
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 1f1e53972063..0f9a0776cf90 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -63,12 +63,6 @@ BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(in_wkup_pdis_en, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_ENABLED);
-BIAS(in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_DISABLED);
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
@@ -389,99 +383,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
- DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
- DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
- DB8500_PIN("GPIO19_AC1", out_hi, "sdi0"), /* DAT0DIR */
- DB8500_PIN("GPIO20_AB4", out_hi, "sdi0"), /* DAT2DIR */
- DB8500_PIN("GPIO22_AA3", in_nopull, "sdi0"), /* FBCLK */
- DB8500_PIN("GPIO23_AA4", out_lo, "sdi0"), /* CLK */
- DB8500_PIN("GPIO24_AB2", in_pu, "sdi0"), /* CMD */
- DB8500_PIN("GPIO25_Y4", in_pu, "sdi0"), /* DAT0 */
- DB8500_PIN("GPIO26_Y2", in_pu, "sdi0"), /* DAT1 */
- DB8500_PIN("GPIO27_AA2", in_pu, "sdi0"), /* DAT2 */
- DB8500_PIN("GPIO28_AA1", in_pu, "sdi0"), /* DAT3 */
- /* SDI0 sleep state */
- DB8500_PIN_SLEEP("GPIO18_AC2", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO19_AC1", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO20_AB4", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO22_AA3", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO23_AA4", slpm_out_lo_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO24_AB2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO25_Y4", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO26_Y2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO27_AA2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO28_AA1", slpm_in_wkup_pdis, "sdi0"),
-
- /* Mux in SDI1 (here called MC1) used for SDIO for CW1200 WLAN */
- DB8500_MUX("mc1_a_1", "mc1", "sdi1"),
- DB8500_PIN("GPIO208_AH16", out_lo, "sdi1"), /* CLK */
- DB8500_PIN("GPIO209_AG15", in_nopull, "sdi1"), /* FBCLK */
- DB8500_PIN("GPIO210_AJ15", in_pu, "sdi1"), /* CMD */
- DB8500_PIN("GPIO211_AG14", in_pu, "sdi1"), /* DAT0 */
- DB8500_PIN("GPIO212_AF13", in_pu, "sdi1"), /* DAT1 */
- DB8500_PIN("GPIO213_AG13", in_pu, "sdi1"), /* DAT2 */
- DB8500_PIN("GPIO214_AH15", in_pu, "sdi1"), /* DAT3 */
- /* SDI1 sleep state */
- DB8500_PIN_SLEEP("GPIO208_AH16", slpm_out_lo_wkup_pdis, "sdi1"), /* CLK */
- DB8500_PIN_SLEEP("GPIO209_AG15", slpm_in_wkup_pdis, "sdi1"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO210_AJ15", slpm_in_wkup_pdis, "sdi1"), /* CMD */
- DB8500_PIN_SLEEP("GPIO211_AG14", slpm_in_wkup_pdis, "sdi1"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO212_AF13", slpm_in_wkup_pdis, "sdi1"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO213_AG13", slpm_in_wkup_pdis, "sdi1"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO214_AH15", slpm_in_wkup_pdis, "sdi1"), /* DAT3 */
-
- /* Mux in SDI2 (here called MC2) used for for PoP eMMC */
- DB8500_MUX("mc2_a_1", "mc2", "sdi2"),
- DB8500_PIN("GPIO128_A5", out_lo, "sdi2"), /* CLK */
- DB8500_PIN("GPIO129_B4", in_pu, "sdi2"), /* CMD */
- DB8500_PIN("GPIO130_C8", in_nopull, "sdi2"), /* FBCLK */
- DB8500_PIN("GPIO131_A12", in_pu, "sdi2"), /* DAT0 */
- DB8500_PIN("GPIO132_C10", in_pu, "sdi2"), /* DAT1 */
- DB8500_PIN("GPIO133_B10", in_pu, "sdi2"), /* DAT2 */
- DB8500_PIN("GPIO134_B9", in_pu, "sdi2"), /* DAT3 */
- DB8500_PIN("GPIO135_A9", in_pu, "sdi2"), /* DAT4 */
- DB8500_PIN("GPIO136_C7", in_pu, "sdi2"), /* DAT5 */
- DB8500_PIN("GPIO137_A7", in_pu, "sdi2"), /* DAT6 */
- DB8500_PIN("GPIO138_C5", in_pu, "sdi2"), /* DAT7 */
- /* SDI2 sleep state */
- DB8500_PIN_SLEEP("GPIO128_A5", out_lo_wkup_pdis, "sdi2"), /* CLK */
- DB8500_PIN_SLEEP("GPIO129_B4", in_wkup_pdis_en, "sdi2"), /* CMD */
- DB8500_PIN_SLEEP("GPIO130_C8", in_wkup_pdis_en, "sdi2"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO131_A12", in_wkup_pdis, "sdi2"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO132_C10", in_wkup_pdis, "sdi2"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO133_B10", in_wkup_pdis, "sdi2"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO134_B9", in_wkup_pdis, "sdi2"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO135_A9", in_wkup_pdis, "sdi2"), /* DAT4 */
- DB8500_PIN_SLEEP("GPIO136_C7", in_wkup_pdis, "sdi2"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO137_A7", in_wkup_pdis, "sdi2"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO138_C5", in_wkup_pdis, "sdi2"), /* DAT7 */
-
- /* Mux in SDI4 (here called MC4) used for for PCB-mounted eMMC */
- DB8500_MUX("mc4_a_1", "mc4", "sdi4"),
- DB8500_PIN("GPIO197_AH24", in_pu, "sdi4"), /* DAT3 */
- DB8500_PIN("GPIO198_AG25", in_pu, "sdi4"), /* DAT2 */
- DB8500_PIN("GPIO199_AH23", in_pu, "sdi4"), /* DAT1 */
- DB8500_PIN("GPIO200_AH26", in_pu, "sdi4"), /* DAT0 */
- DB8500_PIN("GPIO201_AF24", in_pu, "sdi4"), /* CMD */
- DB8500_PIN("GPIO202_AF25", in_nopull, "sdi4"), /* FBCLK */
- DB8500_PIN("GPIO203_AE23", out_lo, "sdi4"), /* CLK */
- DB8500_PIN("GPIO204_AF23", in_pu, "sdi4"), /* DAT7 */
- DB8500_PIN("GPIO205_AG23", in_pu, "sdi4"), /* DAT6 */
- DB8500_PIN("GPIO206_AG24", in_pu, "sdi4"), /* DAT5 */
- DB8500_PIN("GPIO207_AJ23", in_pu, "sdi4"), /* DAT4 */
- /*SDI4 sleep state */
- DB8500_PIN_SLEEP("GPIO197_AH24", slpm_in_wkup_pdis, "sdi4"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO198_AG25", slpm_in_wkup_pdis, "sdi4"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO199_AH23", slpm_in_wkup_pdis, "sdi4"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO200_AH26", slpm_in_wkup_pdis, "sdi4"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO201_AF24", slpm_in_wkup_pdis, "sdi4"), /* CMD */
- DB8500_PIN_SLEEP("GPIO202_AF25", slpm_in_wkup_pdis, "sdi4"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO203_AE23", slpm_out_lo_wkup_pdis, "sdi4"), /* CLK */
- DB8500_PIN_SLEEP("GPIO204_AF23", slpm_in_wkup_pdis, "sdi4"), /* DAT7 */
- DB8500_PIN_SLEEP("GPIO205_AG23", slpm_in_wkup_pdis, "sdi4"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO206_AG24", slpm_in_wkup_pdis, "sdi4"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO207_AJ23", slpm_in_wkup_pdis, "sdi4"), /* DAT4 */
/* Mux in USB pins, drive STP high */
/* USB default state */
@@ -795,10 +696,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
-
- /* Mux in and drive the SDI0 DAT31DIR line high at runtime */
- DB8500_MUX("mc0dat31dir_a_1", "mc0", "sdi0"),
- DB8500_PIN("GPIO21_AB3", out_hi, "sdi0"),
};
/*
@@ -888,8 +785,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
/* Accelerometer interrupt lines */
DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
- /* SD card detect GPIO pin */
- DB8500_PIN_HOG("GPIO95_E8", gpio_in_pu),
/*
* Runtime stuff
* Pull up/down of some sensor GPIO pins, for proximity, HAL sensor
@@ -925,8 +820,6 @@ static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
DB8500_PIN_HOG("GPIO145_C13", pd),
- /* Always drive the MC0 DAT31DIR line high on these boards */
- DB8500_PIN_HOG("GPIO21_AB3", out_hi),
/* Mux in "SM" which is used for the SMSC911x Ethernet adapter */
DB8500_MUX_HOG("sm_b_1", "sm"),
/* User LED */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 04/21] ARM: ux500: move MSP pin control to the device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij, Patrice Chotard
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.
Cc: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Patrice Chotard <patrice.chotard-qxv4g6HH51o@public.gmane.org>
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 63 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 14 ++++++
arch/arm/boot/dts/ste-snowball.dts | 14 ++++++
arch/arm/mach-ux500/board-mop500-pins.c | 30 ------------
4 files changed, 91 insertions(+), 30 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 23583b0546d9..7408d3a898a5 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -425,6 +425,69 @@
};
};
};
+
+ /*
+ * Multi-rate serial ports (MSPs) - MSP3 output is internal and
+ * cannot be muxed onto any pins.
+ */
+ msp0 {
+ msp0_default_mode: msp0_default {
+ default_msp0_mux {
+ ste,function = "msp0";
+ ste,pins = "msp0txrx_a_1", "msp0tfstck_a_1";
+ };
+ default_msp0_cfg {
+ ste,pins =
+ "GPIO12_AC4", /* TXD */
+ "GPIO15_AC3", /* RXD */
+ "GPIO13_AF3", /* TFS */
+ "GPIO14_AE3"; /* TCK */
+ ste,config = <&in_nopull>;
+ };
+ };
+ };
+
+ msp1 {
+ msp1_default_mode: msp1_default {
+ default_mux {
+ ste,function = "msp1";
+ ste,pins = "msp1txrx_a_1", "msp1_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO33_AF2";
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO34_AE1",
+ "GPIO35_AE2",
+ "GPIO36_AG2";
+ ste,config = <&in_nopull>;
+ };
+
+ };
+ };
+
+ msp2 {
+ msp2_default_mode: msp2_default {
+ /* MSP2 usually used for HDMI audio */
+ default_mux {
+ ste,function = "msp2";
+ ste,pins = "msp2_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO193_AH27", /* TXD */
+ "GPIO194_AF27", /* TCK */
+ "GPIO195_AG28"; /* TFS */
+ ste,config = <&in_pd>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO196_AG26"; /* RXD */
+ ste,config = <&out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 845eb25f5d26..85260846deae 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -180,7 +180,21 @@
stericsson,audio-codec = <&codec>;
};
+ msp0: msp@80123000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp0_default_mode>;
+ status = "okay";
+ };
+
msp1: msp@80124000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp1_default_mode>;
+ status = "okay";
+ };
+
+ msp2: msp@80117000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index c2cb3ea637dc..65180b2bc409 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -93,7 +93,21 @@
stericsson,audio-codec = <&codec>;
};
+ msp0: msp@80123000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp0_default_mode>;
+ status = "okay";
+ };
+
msp1: msp@80124000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp1_default_mode>;
+ status = "okay";
+ };
+
+ msp2: msp@80117000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 0f9a0776cf90..f7034cbdc630 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -28,12 +28,10 @@ static enum custom_pin_cfg_t pinsfor;
BIAS(pd, PIN_PULL_DOWN);
BIAS(in_nopull, PIN_INPUT_NOPULL);
-BIAS(in_nopull_slpm_nowkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_DISABLE);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(out_hi, PIN_OUTPUT_HIGH);
BIAS(out_lo, PIN_OUTPUT_LOW);
-BIAS(out_lo_slpm_nowkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
@@ -335,22 +333,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/*
- * uMSP0, mux in 4 pins, regular placement of RX/TX
- * explicitly set the pins to no pull
- */
- DB8500_MUX_HOG("msp0txrx_a_1", "msp0"),
- DB8500_MUX_HOG("msp0tfstck_a_1", "msp0"),
- DB8500_PIN_HOG("GPIO12_AC4", in_nopull), /* TXD */
- DB8500_PIN_HOG("GPIO15_AC3", in_nopull), /* RXD */
- DB8500_PIN_HOG("GPIO13_AF3", in_nopull), /* TFS */
- DB8500_PIN_HOG("GPIO14_AE3", in_nopull), /* TCK */
- /* MSP2 for HDMI, pull down TXD, TCK, TFS */
- DB8500_MUX_HOG("msp2_a_1", "msp2"),
- DB8500_PIN_HOG("GPIO193_AH27", in_pd), /* TXD */
- DB8500_PIN_HOG("GPIO194_AF27", in_pd), /* TCK */
- DB8500_PIN_HOG("GPIO195_AG28", in_pd), /* TFS */
- DB8500_PIN_HOG("GPIO196_AG26", out_lo), /* RXD */
- /*
* LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
* pull-up
* TODO: is this really correct? Snowball doesn't have a LCD.
@@ -363,18 +345,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
* TODO: set for snowball and HREF really??
*/
DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
- /*
- * The following pin sets were known as "runtime pins" before being
- * converted to the pinctrl model. Here we model them as "default"
- * states.
- */
- /* MSP1 for ALSA codec */
- DB8500_MUX_HOG("msp1txrx_a_1", "msp1"),
- DB8500_MUX_HOG("msp1_a_1", "msp1"),
- DB8500_PIN_HOG("GPIO33_AF2", out_lo_slpm_nowkup),
- DB8500_PIN_HOG("GPIO34_AE1", in_nopull_slpm_nowkup),
- DB8500_PIN_HOG("GPIO35_AE2", in_nopull_slpm_nowkup),
- DB8500_PIN_HOG("GPIO36_AG2", in_nopull_slpm_nowkup),
/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 04/21] ARM: ux500: move MSP pin control to the device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 63 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 14 ++++++
arch/arm/boot/dts/ste-snowball.dts | 14 ++++++
arch/arm/mach-ux500/board-mop500-pins.c | 30 ------------
4 files changed, 91 insertions(+), 30 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 23583b0546d9..7408d3a898a5 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -425,6 +425,69 @@
};
};
};
+
+ /*
+ * Multi-rate serial ports (MSPs) - MSP3 output is internal and
+ * cannot be muxed onto any pins.
+ */
+ msp0 {
+ msp0_default_mode: msp0_default {
+ default_msp0_mux {
+ ste,function = "msp0";
+ ste,pins = "msp0txrx_a_1", "msp0tfstck_a_1";
+ };
+ default_msp0_cfg {
+ ste,pins =
+ "GPIO12_AC4", /* TXD */
+ "GPIO15_AC3", /* RXD */
+ "GPIO13_AF3", /* TFS */
+ "GPIO14_AE3"; /* TCK */
+ ste,config = <&in_nopull>;
+ };
+ };
+ };
+
+ msp1 {
+ msp1_default_mode: msp1_default {
+ default_mux {
+ ste,function = "msp1";
+ ste,pins = "msp1txrx_a_1", "msp1_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO33_AF2";
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO34_AE1",
+ "GPIO35_AE2",
+ "GPIO36_AG2";
+ ste,config = <&in_nopull>;
+ };
+
+ };
+ };
+
+ msp2 {
+ msp2_default_mode: msp2_default {
+ /* MSP2 usually used for HDMI audio */
+ default_mux {
+ ste,function = "msp2";
+ ste,pins = "msp2_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO193_AH27", /* TXD */
+ "GPIO194_AF27", /* TCK */
+ "GPIO195_AG28"; /* TFS */
+ ste,config = <&in_pd>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO196_AG26"; /* RXD */
+ ste,config = <&out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 845eb25f5d26..85260846deae 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -180,7 +180,21 @@
stericsson,audio-codec = <&codec>;
};
+ msp0: msp at 80123000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp0_default_mode>;
+ status = "okay";
+ };
+
msp1: msp at 80124000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp1_default_mode>;
+ status = "okay";
+ };
+
+ msp2: msp at 80117000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index c2cb3ea637dc..65180b2bc409 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -93,7 +93,21 @@
stericsson,audio-codec = <&codec>;
};
+ msp0: msp at 80123000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp0_default_mode>;
+ status = "okay";
+ };
+
msp1: msp at 80124000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp1_default_mode>;
+ status = "okay";
+ };
+
+ msp2: msp at 80117000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 0f9a0776cf90..f7034cbdc630 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -28,12 +28,10 @@ static enum custom_pin_cfg_t pinsfor;
BIAS(pd, PIN_PULL_DOWN);
BIAS(in_nopull, PIN_INPUT_NOPULL);
-BIAS(in_nopull_slpm_nowkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_DISABLE);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(out_hi, PIN_OUTPUT_HIGH);
BIAS(out_lo, PIN_OUTPUT_LOW);
-BIAS(out_lo_slpm_nowkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
@@ -335,22 +333,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/*
- * uMSP0, mux in 4 pins, regular placement of RX/TX
- * explicitly set the pins to no pull
- */
- DB8500_MUX_HOG("msp0txrx_a_1", "msp0"),
- DB8500_MUX_HOG("msp0tfstck_a_1", "msp0"),
- DB8500_PIN_HOG("GPIO12_AC4", in_nopull), /* TXD */
- DB8500_PIN_HOG("GPIO15_AC3", in_nopull), /* RXD */
- DB8500_PIN_HOG("GPIO13_AF3", in_nopull), /* TFS */
- DB8500_PIN_HOG("GPIO14_AE3", in_nopull), /* TCK */
- /* MSP2 for HDMI, pull down TXD, TCK, TFS */
- DB8500_MUX_HOG("msp2_a_1", "msp2"),
- DB8500_PIN_HOG("GPIO193_AH27", in_pd), /* TXD */
- DB8500_PIN_HOG("GPIO194_AF27", in_pd), /* TCK */
- DB8500_PIN_HOG("GPIO195_AG28", in_pd), /* TFS */
- DB8500_PIN_HOG("GPIO196_AG26", out_lo), /* RXD */
- /*
* LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
* pull-up
* TODO: is this really correct? Snowball doesn't have a LCD.
@@ -363,18 +345,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
* TODO: set for snowball and HREF really??
*/
DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
- /*
- * The following pin sets were known as "runtime pins" before being
- * converted to the pinctrl model. Here we model them as "default"
- * states.
- */
- /* MSP1 for ALSA codec */
- DB8500_MUX_HOG("msp1txrx_a_1", "msp1"),
- DB8500_MUX_HOG("msp1_a_1", "msp1"),
- DB8500_PIN_HOG("GPIO33_AF2", out_lo_slpm_nowkup),
- DB8500_PIN_HOG("GPIO34_AE1", in_nopull_slpm_nowkup),
- DB8500_PIN_HOG("GPIO35_AE2", in_nopull_slpm_nowkup),
- DB8500_PIN_HOG("GPIO36_AG2", in_nopull_slpm_nowkup),
/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 05/21] ARM: ux500: move GPIO217/218 config to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 13 +++++++++++++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 10 ++++++++++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 5 +++++
arch/arm/mach-ux500/board-mop500-pins.c | 7 -------
4 files changed, 28 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 61b180ea92ca..3f31f9206fb3 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -22,6 +22,8 @@
reg = <0x44>;
interrupt-parent = <&gpio6>;
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tc35893_tvk_mode>;
interrupt-controller;
#interrupt-cells = <1>;
@@ -64,5 +66,16 @@
};
};
};
+ pinctrl {
+ /* Pull up this GPIO pin */
+ tc35893 {
+ tc35893_tvk_mode: tc35893_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO218_AH11";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index cfd7ef306d49..6fc94ea65ab9 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -33,6 +33,8 @@
reg = <0x42>;
interrupt-parent = <&gpio6>;
interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tc35892_hrefprev60_mode>;
interrupt-controller;
#interrupt-cells = <1>;
@@ -71,6 +73,14 @@
};
};
+ tc35892 {
+ tc35892_hrefprev60_mode: tc35892_hrefprev60 {
+ hrefprev60_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index f213222cf220..9aea983e78b5 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -31,6 +31,11 @@
ste,output = <OUTPUT_LOW>;
};
+ gpio_in_pu: gpio_input_pull_up {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,input = <INPUT_PULLUP>;
+ };
+
gpio_out_lo: gpio_output_low {
ste,gpio = <GPIOMODE_ENABLED>;
ste,output = <OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index f7034cbdc630..c032392294a0 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -340,11 +340,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
DB8500_PIN_HOG("GPIO68_E1", in_pu),
DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
- /*
- * STMPE1601/tc35893 keypad IRQ GPIO 218
- * TODO: set for snowball and HREF really??
- */
- DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
@@ -625,8 +620,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
DB8500_PIN_HOG("GPIO6_AF6", in_pu),
DB8500_PIN_HOG("GPIO7_AG5", in_pu),
- /* TC35892 IRQ, pull up the line, let the driver mux in the pin */
- DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
/*
* Runtime stuff: make it possible to mux in the SKE keypad
* and bias the pins
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 05/21] ARM: ux500: move GPIO217/218 config to device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 13 +++++++++++++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 10 ++++++++++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 5 +++++
arch/arm/mach-ux500/board-mop500-pins.c | 7 -------
4 files changed, 28 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 61b180ea92ca..3f31f9206fb3 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -22,6 +22,8 @@
reg = <0x44>;
interrupt-parent = <&gpio6>;
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tc35893_tvk_mode>;
interrupt-controller;
#interrupt-cells = <1>;
@@ -64,5 +66,16 @@
};
};
};
+ pinctrl {
+ /* Pull up this GPIO pin */
+ tc35893 {
+ tc35893_tvk_mode: tc35893_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO218_AH11";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index cfd7ef306d49..6fc94ea65ab9 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -33,6 +33,8 @@
reg = <0x42>;
interrupt-parent = <&gpio6>;
interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tc35892_hrefprev60_mode>;
interrupt-controller;
#interrupt-cells = <1>;
@@ -71,6 +73,14 @@
};
};
+ tc35892 {
+ tc35892_hrefprev60_mode: tc35892_hrefprev60 {
+ hrefprev60_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index f213222cf220..9aea983e78b5 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -31,6 +31,11 @@
ste,output = <OUTPUT_LOW>;
};
+ gpio_in_pu: gpio_input_pull_up {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,input = <INPUT_PULLUP>;
+ };
+
gpio_out_lo: gpio_output_low {
ste,gpio = <GPIOMODE_ENABLED>;
ste,output = <OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index f7034cbdc630..c032392294a0 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -340,11 +340,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
DB8500_PIN_HOG("GPIO68_E1", in_pu),
DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
- /*
- * STMPE1601/tc35893 keypad IRQ GPIO 218
- * TODO: set for snowball and HREF really??
- */
- DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
@@ -625,8 +620,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
DB8500_PIN_HOG("GPIO6_AF6", in_pu),
DB8500_PIN_HOG("GPIO7_AG5", in_pu),
- /* TC35892 IRQ, pull up the line, let the driver mux in the pin */
- DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
/*
* Runtime stuff: make it possible to mux in the SKE keypad
* and bias the pins
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 06/21] ARM: ux500: move MUSB pin config to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 55 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 6 +++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 13 ++++++
arch/arm/boot/dts/ste-snowball.dts | 5 +++
arch/arm/mach-ux500/board-mop500-pins.c | 25 ------------
5 files changed, 79 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 7408d3a898a5..6868fec95d64 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -488,6 +488,61 @@
};
};
};
+
+
+ musb {
+ musb_default_mode: musb_default {
+ default_mux {
+ ste,function = "usb";
+ ste,pins = "usb_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO256_AF28", /* NXT */
+ "GPIO258_AD29", /* XCLK */
+ "GPIO259_AC29", /* DIR */
+ "GPIO260_AD28", /* DAT7 */
+ "GPIO261_AD26", /* DAT6 */
+ "GPIO262_AE26", /* DAT5 */
+ "GPIO263_AG29", /* DAT4 */
+ "GPIO264_AE27", /* DAT3 */
+ "GPIO265_AD27", /* DAT2 */
+ "GPIO266_AC28", /* DAT1 */
+ "GPIO267_AC27"; /* DAT0 */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO257_AE29"; /* STP */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ musb_sleep_mode: musb_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO256_AF28", /* NXT */
+ "GPIO258_AD29", /* XCLK */
+ "GPIO259_AC29"; /* DIR */
+ ste,config = <&slpm_wkup_pdis_en>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO257_AE29"; /* STP */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins =
+ "GPIO260_AD28", /* DAT7 */
+ "GPIO261_AD26", /* DAT6 */
+ "GPIO262_AE26", /* DAT5 */
+ "GPIO263_AG29", /* DAT4 */
+ "GPIO264_AE27", /* DAT3 */
+ "GPIO265_AD27", /* DAT2 */
+ "GPIO266_AC28", /* DAT1 */
+ "GPIO267_AC27"; /* DAT0 */
+ ste,config = <&slpm_in_wkup_pdis_en>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 85260846deae..4fda2d933488 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -30,6 +30,12 @@
};
soc {
+ usb_per5@a03e0000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&musb_default_mode>;
+ pinctrl-1 = <&musb_sleep_mode>;
+ };
+
uart@80120000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&uart0_default_mode>;
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index 9aea983e78b5..9f3e87573f86 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -41,6 +41,12 @@
ste,output = <OUTPUT_LOW>;
};
+ slpm_wkup_pdis_en: slpm_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_in_pu: slpm_in_pu {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_INPUT_PULLUP>;
@@ -54,6 +60,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_in_wkup_pdis_en: slpm_in_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_out_lo: slpm_out_lo {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 65180b2bc409..4763b805e754 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -85,6 +85,11 @@
};
soc {
+ usb_per5@a03e0000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&musb_default_mode>;
+ pinctrl-1 = <&musb_sleep_mode>;
+ };
sound {
compatible = "stericsson,snd-soc-mop500";
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index c032392294a0..a6d431bd0659 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -30,7 +30,6 @@ BIAS(pd, PIN_PULL_DOWN);
BIAS(in_nopull, PIN_INPUT_NOPULL);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
-BIAS(out_hi, PIN_OUTPUT_HIGH);
BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
@@ -47,18 +46,12 @@ BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
/* Sleep modes */
BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
@@ -349,24 +342,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in USB pins, drive STP high */
- /* USB default state */
- DB8500_MUX("usb_a_1", "usb", "ab8500-usb.0"),
- DB8500_PIN("GPIO257_AE29", out_hi, "ab8500-usb.0"), /* STP */
- /* USB sleep state */
- DB8500_PIN_SLEEP("GPIO256_AF28", slpm_wkup_pdis_en, "ab8500-usb.0"), /* NXT */
- DB8500_PIN_SLEEP("GPIO257_AE29", slpm_out_hi_wkup_pdis, "ab8500-usb.0"), /* STP */
- DB8500_PIN_SLEEP("GPIO258_AD29", slpm_wkup_pdis_en, "ab8500-usb.0"), /* XCLK */
- DB8500_PIN_SLEEP("GPIO259_AC29", slpm_wkup_pdis_en, "ab8500-usb.0"), /* DIR */
- DB8500_PIN_SLEEP("GPIO260_AD28", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT7 */
- DB8500_PIN_SLEEP("GPIO261_AD26", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO262_AE26", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO263_AG29", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT4 */
- DB8500_PIN_SLEEP("GPIO264_AE27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO265_AD27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO266_AC28", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO267_AC27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT0 */
-
/* Mux in SPI2 pins on the "other C1" altfunction */
DB8500_MUX("spi2_oc1_2", "spi2", "spi2"),
DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 06/21] ARM: ux500: move MUSB pin config to device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 55 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 6 +++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 13 ++++++
arch/arm/boot/dts/ste-snowball.dts | 5 +++
arch/arm/mach-ux500/board-mop500-pins.c | 25 ------------
5 files changed, 79 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 7408d3a898a5..6868fec95d64 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -488,6 +488,61 @@
};
};
};
+
+
+ musb {
+ musb_default_mode: musb_default {
+ default_mux {
+ ste,function = "usb";
+ ste,pins = "usb_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO256_AF28", /* NXT */
+ "GPIO258_AD29", /* XCLK */
+ "GPIO259_AC29", /* DIR */
+ "GPIO260_AD28", /* DAT7 */
+ "GPIO261_AD26", /* DAT6 */
+ "GPIO262_AE26", /* DAT5 */
+ "GPIO263_AG29", /* DAT4 */
+ "GPIO264_AE27", /* DAT3 */
+ "GPIO265_AD27", /* DAT2 */
+ "GPIO266_AC28", /* DAT1 */
+ "GPIO267_AC27"; /* DAT0 */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO257_AE29"; /* STP */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ musb_sleep_mode: musb_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO256_AF28", /* NXT */
+ "GPIO258_AD29", /* XCLK */
+ "GPIO259_AC29"; /* DIR */
+ ste,config = <&slpm_wkup_pdis_en>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO257_AE29"; /* STP */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins =
+ "GPIO260_AD28", /* DAT7 */
+ "GPIO261_AD26", /* DAT6 */
+ "GPIO262_AE26", /* DAT5 */
+ "GPIO263_AG29", /* DAT4 */
+ "GPIO264_AE27", /* DAT3 */
+ "GPIO265_AD27", /* DAT2 */
+ "GPIO266_AC28", /* DAT1 */
+ "GPIO267_AC27"; /* DAT0 */
+ ste,config = <&slpm_in_wkup_pdis_en>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 85260846deae..4fda2d933488 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -30,6 +30,12 @@
};
soc {
+ usb_per5 at a03e0000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&musb_default_mode>;
+ pinctrl-1 = <&musb_sleep_mode>;
+ };
+
uart at 80120000 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&uart0_default_mode>;
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index 9aea983e78b5..9f3e87573f86 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -41,6 +41,12 @@
ste,output = <OUTPUT_LOW>;
};
+ slpm_wkup_pdis_en: slpm_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_in_pu: slpm_in_pu {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_INPUT_PULLUP>;
@@ -54,6 +60,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_in_wkup_pdis_en: slpm_in_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_out_lo: slpm_out_lo {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 65180b2bc409..4763b805e754 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -85,6 +85,11 @@
};
soc {
+ usb_per5 at a03e0000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&musb_default_mode>;
+ pinctrl-1 = <&musb_sleep_mode>;
+ };
sound {
compatible = "stericsson,snd-soc-mop500";
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index c032392294a0..a6d431bd0659 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -30,7 +30,6 @@ BIAS(pd, PIN_PULL_DOWN);
BIAS(in_nopull, PIN_INPUT_NOPULL);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
-BIAS(out_hi, PIN_OUTPUT_HIGH);
BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
@@ -47,18 +46,12 @@ BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
/* Sleep modes */
BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
@@ -349,24 +342,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in USB pins, drive STP high */
- /* USB default state */
- DB8500_MUX("usb_a_1", "usb", "ab8500-usb.0"),
- DB8500_PIN("GPIO257_AE29", out_hi, "ab8500-usb.0"), /* STP */
- /* USB sleep state */
- DB8500_PIN_SLEEP("GPIO256_AF28", slpm_wkup_pdis_en, "ab8500-usb.0"), /* NXT */
- DB8500_PIN_SLEEP("GPIO257_AE29", slpm_out_hi_wkup_pdis, "ab8500-usb.0"), /* STP */
- DB8500_PIN_SLEEP("GPIO258_AD29", slpm_wkup_pdis_en, "ab8500-usb.0"), /* XCLK */
- DB8500_PIN_SLEEP("GPIO259_AC29", slpm_wkup_pdis_en, "ab8500-usb.0"), /* DIR */
- DB8500_PIN_SLEEP("GPIO260_AD28", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT7 */
- DB8500_PIN_SLEEP("GPIO261_AD26", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO262_AE26", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO263_AG29", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT4 */
- DB8500_PIN_SLEEP("GPIO264_AE27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO265_AD27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO266_AC28", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO267_AC27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT0 */
-
/* Mux in SPI2 pins on the "other C1" altfunction */
DB8500_MUX("spi2_oc1_2", "spi2", "spi2"),
DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 07/21] ARM: ux500: move SPI pin config to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 61 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 22 ++++++++++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 31 +++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 19 --------
4 files changed, 114 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 6868fec95d64..ec990d8e1029 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -215,6 +215,67 @@
};
};
+ /* Settings for all SPI default and sleep states */
+ spi2 {
+ spi2_default_mode: spi_default {
+ default_mux {
+ ste,function = "spi2";
+ ste,pins = "spi2_oc1_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO216_AG12"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO215_AH13", /* TXD */
+ "GPIO217_AH12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ };
+
+ spi2_idle_mode: spi_idle {
+ /*
+ * The idle mode is basically sleep mode sans wakeups. Also
+ * note that we have muxes the pins off the function here
+ * as we do not state any muxing.
+ */
+ idle_cfg1 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_pdis>;
+ };
+ idle_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ idle_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_pdis>;
+ };
+ };
+
+ spi2_sleep_mode: spi_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO216_AG12", /* FRM */
+ "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_wkup_pdis>;
+ };
+ };
+ };
+
/* Settings for all MMC/SD/SDIO default and sleep states */
sdi0 {
/* This is the external SD card slot, 4 bits wide */
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 6fc94ea65ab9..32295e396ff8 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -51,6 +51,15 @@
};
};
+ ssp@80002000 {
+ /*
+ * On the first generation boards, this SSP/SPI port was connected
+ * to the AB8500.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_hrefprev60_mode>;
+ };
+
vmmci: regulator-gpio {
gpios = <&tc3589x_gpio 18 0x4>;
enable-gpio = <&tc3589x_gpio 17 0x4>;
@@ -59,6 +68,19 @@
};
pinctrl {
+ ssp0 {
+ ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
+ hrefprev60_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+
+ };
+ };
sdi0 {
/* This additional pin needed on early MOP500 and HREFs previous to v60 */
sdi0_default_mode: sdi0_default {
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index 9f3e87573f86..456a25fbfaee 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -41,6 +41,23 @@
ste,output = <OUTPUT_LOW>;
};
+ gpio_out_hi: gpio_output_high {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,output = <OUTPUT_HIGH>;
+ };
+
+ slpm_pdis: slpm_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
+ slpm_wkup_pdis: slpm_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_wkup_pdis_en: slpm_wkup_pdis_en {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
@@ -53,6 +70,13 @@
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
};
+ slpm_in_pdis: slpm_in_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_in_wkup_pdis: slpm_in_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_DIR_INPUT>;
@@ -86,6 +110,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_out_lo_pdis: slpm_out_lo_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index a6d431bd0659..8fba58c98da2 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -342,22 +342,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in SPI2 pins on the "other C1" altfunction */
- DB8500_MUX("spi2_oc1_2", "spi2", "spi2"),
- DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
- DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */
- DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */
- DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */
- /* SPI2 idle state */
- DB8500_PIN_IDLE("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_IDLE("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_IDLE("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
- /* SPI2 sleep state */
- DB8500_PIN_SLEEP("GPIO216_AG12", slpm_in_wkup_pdis, "spi2"), /* FRM */
- DB8500_PIN_SLEEP("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_SLEEP("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_SLEEP("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
-
/* ske default state */
DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
@@ -582,9 +566,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
* on-chip pins as the HREFv60 and later does.
*/
static struct pinctrl_map __initdata mop500_pinmap[] = {
- /* Mux in SSP0, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
/*
* XENON Flashgun on image processor GPIO (controlled from image
* processor firmware), mux in these image processor GPIO lines 0
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 07/21] ARM: ux500: move SPI pin config to device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 61 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-hrefprev60.dtsi | 22 ++++++++++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 31 +++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 19 --------
4 files changed, 114 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 6868fec95d64..ec990d8e1029 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -215,6 +215,67 @@
};
};
+ /* Settings for all SPI default and sleep states */
+ spi2 {
+ spi2_default_mode: spi_default {
+ default_mux {
+ ste,function = "spi2";
+ ste,pins = "spi2_oc1_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO216_AG12"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO215_AH13", /* TXD */
+ "GPIO217_AH12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ };
+
+ spi2_idle_mode: spi_idle {
+ /*
+ * The idle mode is basically sleep mode sans wakeups. Also
+ * note that we have muxes the pins off the function here
+ * as we do not state any muxing.
+ */
+ idle_cfg1 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_pdis>;
+ };
+ idle_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ idle_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_pdis>;
+ };
+ };
+
+ spi2_sleep_mode: spi_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO216_AG12", /* FRM */
+ "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_wkup_pdis>;
+ };
+ };
+ };
+
/* Settings for all MMC/SD/SDIO default and sleep states */
sdi0 {
/* This is the external SD card slot, 4 bits wide */
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 6fc94ea65ab9..32295e396ff8 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -51,6 +51,15 @@
};
};
+ ssp at 80002000 {
+ /*
+ * On the first generation boards, this SSP/SPI port was connected
+ * to the AB8500.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_hrefprev60_mode>;
+ };
+
vmmci: regulator-gpio {
gpios = <&tc3589x_gpio 18 0x4>;
enable-gpio = <&tc3589x_gpio 17 0x4>;
@@ -59,6 +68,19 @@
};
pinctrl {
+ ssp0 {
+ ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
+ hrefprev60_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+
+ };
+ };
sdi0 {
/* This additional pin needed on early MOP500 and HREFs previous to v60 */
sdi0_default_mode: sdi0_default {
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index 9f3e87573f86..456a25fbfaee 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -41,6 +41,23 @@
ste,output = <OUTPUT_LOW>;
};
+ gpio_out_hi: gpio_output_high {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,output = <OUTPUT_HIGH>;
+ };
+
+ slpm_pdis: slpm_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
+ slpm_wkup_pdis: slpm_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_wkup_pdis_en: slpm_wkup_pdis_en {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
@@ -53,6 +70,13 @@
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
};
+ slpm_in_pdis: slpm_in_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_in_wkup_pdis: slpm_in_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_DIR_INPUT>;
@@ -86,6 +110,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_out_lo_pdis: slpm_out_lo_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index a6d431bd0659..8fba58c98da2 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -342,22 +342,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in SPI2 pins on the "other C1" altfunction */
- DB8500_MUX("spi2_oc1_2", "spi2", "spi2"),
- DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
- DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */
- DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */
- DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */
- /* SPI2 idle state */
- DB8500_PIN_IDLE("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_IDLE("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_IDLE("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
- /* SPI2 sleep state */
- DB8500_PIN_SLEEP("GPIO216_AG12", slpm_in_wkup_pdis, "spi2"), /* FRM */
- DB8500_PIN_SLEEP("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_SLEEP("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_SLEEP("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
-
/* ske default state */
DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
@@ -582,9 +566,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
* on-chip pins as the HREFv60 and later does.
*/
static struct pinctrl_map __initdata mop500_pinmap[] = {
- /* Mux in SSP0, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
/*
* XENON Flashgun on image processor GPIO (controlled from image
* processor firmware), mux in these image processor GPIO lines 0
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 08/21] ARM: ux500: create MCDE node to collect resources
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
As we need to connect resources such as pin mappings and clocks
when deleting board files, we create a MCDE node even though there
is no driver for it. As it is only using standard bindings right
now, this does not matter much. When a proper driver is written
for the MCDE, it can augment this node with custom properties.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-dbx5x0.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 50ff5ab372d8..e0853ea02df2 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -1002,6 +1002,23 @@
status = "disabled";
};
+ mcde@a0350000 {
+ compatible = "stericsson,mcde";
+ reg = <0xa0350000 0x1000>, /* MCDE */
+ <0xa0351000 0x1000>, /* DSI link 1 */
+ <0xa0352000 0x1000>, /* DSI link 2 */
+ <0xa0353000 0x1000>; /* DSI link 3 */
+ interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
+ <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
+ <&prcmu_clk PRCMU_PLLDSI>, /* HDMI clock */
+ <&prcmu_clk PRCMU_DSI0CLK>, /* DSI 0 */
+ <&prcmu_clk PRCMU_DSI1CLK>, /* DSI 1 */
+ <&prcmu_clk PRCMU_DSI0ESCCLK>, /* TVout clock 0 */
+ <&prcmu_clk PRCMU_DSI1ESCCLK>, /* TVout clock 1 */
+ <&prcmu_clk PRCMU_DSI2ESCCLK>; /* TVout clock 2 */
+ };
+
cryp@a03cb000 {
compatible = "stericsson,ux500-cryp";
reg = <0xa03cb000 0x1000>;
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 08/21] ARM: ux500: create MCDE node to collect resources
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
As we need to connect resources such as pin mappings and clocks
when deleting board files, we create a MCDE node even though there
is no driver for it. As it is only using standard bindings right
now, this does not matter much. When a proper driver is written
for the MCDE, it can augment this node with custom properties.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-dbx5x0.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 50ff5ab372d8..e0853ea02df2 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -1002,6 +1002,23 @@
status = "disabled";
};
+ mcde at a0350000 {
+ compatible = "stericsson,mcde";
+ reg = <0xa0350000 0x1000>, /* MCDE */
+ <0xa0351000 0x1000>, /* DSI link 1 */
+ <0xa0352000 0x1000>, /* DSI link 2 */
+ <0xa0353000 0x1000>; /* DSI link 3 */
+ interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
+ <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
+ <&prcmu_clk PRCMU_PLLDSI>, /* HDMI clock */
+ <&prcmu_clk PRCMU_DSI0CLK>, /* DSI 0 */
+ <&prcmu_clk PRCMU_DSI1CLK>, /* DSI 1 */
+ <&prcmu_clk PRCMU_DSI0ESCCLK>, /* TVout clock 0 */
+ <&prcmu_clk PRCMU_DSI1ESCCLK>, /* TVout clock 1 */
+ <&prcmu_clk PRCMU_DSI2ESCCLK>; /* TVout clock 2 */
+ };
+
cryp at a03cb000 {
compatible = "stericsson,ux500-cryp";
reg = <0xa03cb000 0x1000>;
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 09/21] ARM: ux500: move MCDE pin config to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 27 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 6 ++++++
arch/arm/boot/dts/ste-snowball.dts | 6 ++++++
arch/arm/mach-ux500/board-mop500-pins.c | 19 ------------------
4 files changed, 39 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index ec990d8e1029..779829a1e143 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -604,6 +604,33 @@
};
};
};
+
+ mcde {
+ lcd_default_mode: lcd_default {
+ default_mux {
+ /* Mux in VSI0 and all the data lines */
+ ste,function = "lcd";
+ ste,pins =
+ "lcdvsi0_a_1", /* VSI0 for LCD */
+ "lcd_d0_d7_a_1", /* Data lines */
+ "lcd_d8_d11_a_1", /* TV-out */
+ "lcdaclk_b_1", /* Clock line for TV-out */
+ "lcdvsi1_a_1"; /* VSI1 for HDMI */
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO68_E1", /* VSI0 */
+ "GPIO69_E2"; /* VSI1 */
+ ste,config = <&in_pu>;
+ };
+ };
+ lcd_sleep_mode: lcd_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO69_E2"; /* VSI1 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 4fda2d933488..56772c3ebb28 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -261,5 +261,11 @@
};
};
};
+
+ mcde@a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 4763b805e754..53febe58a1cb 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -362,5 +362,11 @@
};
};
};
+
+ mcde@a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 8fba58c98da2..4cc4cb151474 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -46,8 +46,6 @@ BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
/* Sleep modes */
BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
@@ -325,23 +323,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /*
- * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
- * pull-up
- * TODO: is this really correct? Snowball doesn't have a LCD.
- */
- DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
- DB8500_PIN_HOG("GPIO68_E1", in_pu),
- DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
- /* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
- DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
- DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
- /* Mux in LCD VSI1 and pull it up for MCDE HDMI output */
- DB8500_MUX("lcdvsi1_a_1", "lcd", "0-0070"),
- DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
- /* LCD VSI1 sleep state */
- DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
-
/* ske default state */
DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 09/21] ARM: ux500: move MCDE pin config to device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 27 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 6 ++++++
arch/arm/boot/dts/ste-snowball.dts | 6 ++++++
arch/arm/mach-ux500/board-mop500-pins.c | 19 ------------------
4 files changed, 39 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index ec990d8e1029..779829a1e143 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -604,6 +604,33 @@
};
};
};
+
+ mcde {
+ lcd_default_mode: lcd_default {
+ default_mux {
+ /* Mux in VSI0 and all the data lines */
+ ste,function = "lcd";
+ ste,pins =
+ "lcdvsi0_a_1", /* VSI0 for LCD */
+ "lcd_d0_d7_a_1", /* Data lines */
+ "lcd_d8_d11_a_1", /* TV-out */
+ "lcdaclk_b_1", /* Clock line for TV-out */
+ "lcdvsi1_a_1"; /* VSI1 for HDMI */
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO68_E1", /* VSI0 */
+ "GPIO69_E2"; /* VSI1 */
+ ste,config = <&in_pu>;
+ };
+ };
+ lcd_sleep_mode: lcd_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO69_E2"; /* VSI1 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 4fda2d933488..56772c3ebb28 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -261,5 +261,11 @@
};
};
};
+
+ mcde at a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 4763b805e754..53febe58a1cb 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -362,5 +362,11 @@
};
};
};
+
+ mcde at a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 8fba58c98da2..4cc4cb151474 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -46,8 +46,6 @@ BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
/* Sleep modes */
BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
@@ -325,23 +323,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /*
- * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
- * pull-up
- * TODO: is this really correct? Snowball doesn't have a LCD.
- */
- DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
- DB8500_PIN_HOG("GPIO68_E1", in_pu),
- DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
- /* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
- DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
- DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
- /* Mux in LCD VSI1 and pull it up for MCDE HDMI output */
- DB8500_MUX("lcdvsi1_a_1", "lcd", "0-0070"),
- DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
- /* LCD VSI1 sleep state */
- DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
-
/* ske default state */
DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 10/21] ARM: ux500: move SKE pin config to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:03 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves the SKE keypad pin control table out of the board
file and into the device tree. This was previously set to be
active on all MOP500 and HREF boards but after reading the
schematic this seems incorrect: the HREFv60 and later uses
one of these for MC5 and no reference designs have the SKE
connected to any hardware so just leave the pins alone
in the power-on state.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 90 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 7 ++
arch/arm/mach-ux500/board-mop500-pins.c | 87 -------------------------
3 files changed, 97 insertions(+), 87 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 779829a1e143..854a4a6e521e 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -631,6 +631,96 @@
};
};
};
+
+ ske {
+ /* SKE keys on position 2 in an 8x8 matrix */
+ ske_kpa2_default_mode: ske_kpa2_default {
+ default_mux {
+ ste,function = "kp";
+ ste,pins = "kp_a_2";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO153_B17", /* I7 */
+ "GPIO154_C16", /* I6 */
+ "GPIO155_C19", /* I5 */
+ "GPIO156_C17", /* I4 */
+ "GPIO161_D21", /* I3 */
+ "GPIO162_D20", /* I2 */
+ "GPIO163_C20", /* I1 */
+ "GPIO164_B21"; /* I0 */
+ ste,config = <&in_pd>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO157_A18", /* O7 */
+ "GPIO158_C18", /* O6 */
+ "GPIO159_B19", /* O5 */
+ "GPIO160_B20", /* O4 */
+ "GPIO165_C21", /* O3 */
+ "GPIO166_A22", /* O2 */
+ "GPIO167_B24", /* O1 */
+ "GPIO168_C22"; /* O0 */
+ ste,config = <&out_lo>;
+ };
+ };
+ ske_kpa2_sleep_mode: ske_kpa2_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO153_B17", /* I7 */
+ "GPIO154_C16", /* I6 */
+ "GPIO155_C19", /* I5 */
+ "GPIO156_C17", /* I4 */
+ "GPIO161_D21", /* I3 */
+ "GPIO162_D20", /* I2 */
+ "GPIO163_C20", /* I1 */
+ "GPIO164_B21"; /* I0 */
+ ste,config = <&slpm_in_pu_wkup_pdis_en>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO157_A18", /* O7 */
+ "GPIO158_C18", /* O6 */
+ "GPIO159_B19", /* O5 */
+ "GPIO160_B20", /* O4 */
+ "GPIO165_C21", /* O3 */
+ "GPIO166_A22", /* O2 */
+ "GPIO167_B24", /* O1 */
+ "GPIO168_C22"; /* O0 */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ };
+ /*
+ * SKE keys on position 1 and "other C1" combi giving
+ * six rows of six keys.
+ */
+ ske_kpaoc1_default_mode: ske_kpaoc1_default {
+ default_mux {
+ ste,function = "kp";
+ ste,pins = "kp_a_1", "kp_oc1_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO91_B6", /* KP_O0 */
+ "GPIO90_A3", /* KP_O1 */
+ "GPIO87_B3", /* KP_O2 */
+ "GPIO86_C6", /* KP_O3 */
+ "GPIO96_D8", /* KP_O6 */
+ "GPIO94_D7"; /* KP_O7 */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO93_B7", /* KP_I0 */
+ "GPIO92_D6", /* KP_I1 */
+ "GPIO89_E6", /* KP_I2 */
+ "GPIO88_C4", /* KP_I3 */
+ "GPIO97_D9", /* KP_I6 */
+ "GPIO95_E8"; /* KP_I7 */
+ ste,config = <&in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index 456a25fbfaee..ee143b0a5baa 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -91,6 +91,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
};
+ slpm_in_pu_wkup_pdis_en: slpm_in_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_INPUT_PULLUP>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_out_lo: slpm_out_lo {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 4cc4cb151474..07ddb89a6dbe 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -323,42 +323,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /* ske default state */
- DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
- DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN("GPIO154_C16", in_pd, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN("GPIO155_C19", in_pd, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN("GPIO156_C17", in_pd, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN("GPIO161_D21", in_pd, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN("GPIO162_D20", in_pd, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN("GPIO163_C20", in_pd, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN("GPIO164_B21", in_pd, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN("GPIO157_A18", out_lo, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN("GPIO158_C18", out_lo, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN("GPIO159_B19", out_lo, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN("GPIO160_B20", out_lo, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN("GPIO165_C21", out_lo, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN("GPIO166_A22", out_lo, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN("GPIO167_B24", out_lo, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN("GPIO168_C22", out_lo, "nmk-ske-keypad"), /* O0 */
- /* ske sleep state */
- DB8500_PIN_SLEEP("GPIO153_B17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN_SLEEP("GPIO154_C16", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN_SLEEP("GPIO155_C19", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN_SLEEP("GPIO156_C17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN_SLEEP("GPIO161_D21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN_SLEEP("GPIO162_D20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN_SLEEP("GPIO163_C20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN_SLEEP("GPIO164_B21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN_SLEEP("GPIO157_A18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN_SLEEP("GPIO158_C18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN_SLEEP("GPIO159_B19", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN_SLEEP("GPIO160_B20", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN_SLEEP("GPIO165_C21", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
-
/* STM APE pins states */
DB8500_MUX_STATE("stmape_c_1", "stmape",
"stm", "ape_mipi34"),
@@ -561,41 +525,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
* Runtime stuff: make it possible to mux in the SKE keypad
* and bias the pins
*/
- /* ske default state */
- DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
- DB8500_PIN("GPIO153_B17", in_pu, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN("GPIO154_C16", in_pu, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN("GPIO155_C19", in_pu, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN("GPIO156_C17", in_pu, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN("GPIO161_D21", in_pu, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN("GPIO162_D20", in_pu, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN("GPIO163_C20", in_pu, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN("GPIO164_B21", in_pu, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN("GPIO157_A18", out_lo, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN("GPIO158_C18", out_lo, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN("GPIO159_B19", out_lo, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN("GPIO160_B20", out_lo, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN("GPIO165_C21", out_lo, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN("GPIO166_A22", out_lo, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN("GPIO167_B24", out_lo, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN("GPIO168_C22", out_lo, "nmk-ske-keypad"), /* O0 */
- /* ske sleep state */
- DB8500_PIN_SLEEP("GPIO153_B17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN_SLEEP("GPIO154_C16", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN_SLEEP("GPIO155_C19", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN_SLEEP("GPIO156_C17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN_SLEEP("GPIO161_D21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN_SLEEP("GPIO162_D20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN_SLEEP("GPIO163_C20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN_SLEEP("GPIO164_B21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN_SLEEP("GPIO157_A18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN_SLEEP("GPIO158_C18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN_SLEEP("GPIO159_B19", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN_SLEEP("GPIO160_B20", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN_SLEEP("GPIO165_C21", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
};
/*
@@ -655,22 +584,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
- /*
- * SKE keyboard partly on alt A and partly on "Other alt C1"
- * Driver KP_O1,2,3,6,7 low and pull up KP_I 0,2,3 for three
- * rows of 6 keys, then pull up force sensing interrup and
- * drive reset and force sensing WU low.
- */
- DB8500_MUX_HOG("kp_a_1", "kp"),
- DB8500_MUX_HOG("kp_oc1_1", "kp"),
- DB8500_PIN_HOG("GPIO90_A3", out_lo), /* KP_O1 */
- DB8500_PIN_HOG("GPIO87_B3", out_lo), /* KP_O2 */
- DB8500_PIN_HOG("GPIO86_C6", out_lo), /* KP_O3 */
- DB8500_PIN_HOG("GPIO96_D8", out_lo), /* KP_O6 */
- DB8500_PIN_HOG("GPIO94_D7", out_lo), /* KP_O7 */
- DB8500_PIN_HOG("GPIO93_B7", in_pu), /* KP_I0 */
- DB8500_PIN_HOG("GPIO89_E6", in_pu), /* KP_I2 */
- DB8500_PIN_HOG("GPIO88_C4", in_pu), /* KP_I3 */
DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */
DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */
DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 10/21] ARM: ux500: move SKE pin config to device tree
@ 2013-11-17 11:03 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This moves the SKE keypad pin control table out of the board
file and into the device tree. This was previously set to be
active on all MOP500 and HREF boards but after reading the
schematic this seems incorrect: the HREFv60 and later uses
one of these for MC5 and no reference designs have the SKE
connected to any hardware so just leave the pins alone
in the power-on state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 90 ++++++++++++++++++++++++++
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 7 ++
arch/arm/mach-ux500/board-mop500-pins.c | 87 -------------------------
3 files changed, 97 insertions(+), 87 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 779829a1e143..854a4a6e521e 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -631,6 +631,96 @@
};
};
};
+
+ ske {
+ /* SKE keys on position 2 in an 8x8 matrix */
+ ske_kpa2_default_mode: ske_kpa2_default {
+ default_mux {
+ ste,function = "kp";
+ ste,pins = "kp_a_2";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO153_B17", /* I7 */
+ "GPIO154_C16", /* I6 */
+ "GPIO155_C19", /* I5 */
+ "GPIO156_C17", /* I4 */
+ "GPIO161_D21", /* I3 */
+ "GPIO162_D20", /* I2 */
+ "GPIO163_C20", /* I1 */
+ "GPIO164_B21"; /* I0 */
+ ste,config = <&in_pd>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO157_A18", /* O7 */
+ "GPIO158_C18", /* O6 */
+ "GPIO159_B19", /* O5 */
+ "GPIO160_B20", /* O4 */
+ "GPIO165_C21", /* O3 */
+ "GPIO166_A22", /* O2 */
+ "GPIO167_B24", /* O1 */
+ "GPIO168_C22"; /* O0 */
+ ste,config = <&out_lo>;
+ };
+ };
+ ske_kpa2_sleep_mode: ske_kpa2_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO153_B17", /* I7 */
+ "GPIO154_C16", /* I6 */
+ "GPIO155_C19", /* I5 */
+ "GPIO156_C17", /* I4 */
+ "GPIO161_D21", /* I3 */
+ "GPIO162_D20", /* I2 */
+ "GPIO163_C20", /* I1 */
+ "GPIO164_B21"; /* I0 */
+ ste,config = <&slpm_in_pu_wkup_pdis_en>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO157_A18", /* O7 */
+ "GPIO158_C18", /* O6 */
+ "GPIO159_B19", /* O5 */
+ "GPIO160_B20", /* O4 */
+ "GPIO165_C21", /* O3 */
+ "GPIO166_A22", /* O2 */
+ "GPIO167_B24", /* O1 */
+ "GPIO168_C22"; /* O0 */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ };
+ /*
+ * SKE keys on position 1 and "other C1" combi giving
+ * six rows of six keys.
+ */
+ ske_kpaoc1_default_mode: ske_kpaoc1_default {
+ default_mux {
+ ste,function = "kp";
+ ste,pins = "kp_a_1", "kp_oc1_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO91_B6", /* KP_O0 */
+ "GPIO90_A3", /* KP_O1 */
+ "GPIO87_B3", /* KP_O2 */
+ "GPIO86_C6", /* KP_O3 */
+ "GPIO96_D8", /* KP_O6 */
+ "GPIO94_D7"; /* KP_O7 */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO93_B7", /* KP_I0 */
+ "GPIO92_D6", /* KP_I1 */
+ "GPIO89_E6", /* KP_I2 */
+ "GPIO88_C4", /* KP_I3 */
+ "GPIO97_D9", /* KP_I6 */
+ "GPIO95_E8"; /* KP_I7 */
+ ste,config = <&in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index 456a25fbfaee..ee143b0a5baa 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -91,6 +91,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
};
+ slpm_in_pu_wkup_pdis_en: slpm_in_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_INPUT_PULLUP>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_out_lo: slpm_out_lo {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 4cc4cb151474..07ddb89a6dbe 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -323,42 +323,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /* ske default state */
- DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
- DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN("GPIO154_C16", in_pd, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN("GPIO155_C19", in_pd, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN("GPIO156_C17", in_pd, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN("GPIO161_D21", in_pd, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN("GPIO162_D20", in_pd, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN("GPIO163_C20", in_pd, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN("GPIO164_B21", in_pd, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN("GPIO157_A18", out_lo, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN("GPIO158_C18", out_lo, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN("GPIO159_B19", out_lo, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN("GPIO160_B20", out_lo, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN("GPIO165_C21", out_lo, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN("GPIO166_A22", out_lo, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN("GPIO167_B24", out_lo, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN("GPIO168_C22", out_lo, "nmk-ske-keypad"), /* O0 */
- /* ske sleep state */
- DB8500_PIN_SLEEP("GPIO153_B17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN_SLEEP("GPIO154_C16", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN_SLEEP("GPIO155_C19", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN_SLEEP("GPIO156_C17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN_SLEEP("GPIO161_D21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN_SLEEP("GPIO162_D20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN_SLEEP("GPIO163_C20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN_SLEEP("GPIO164_B21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN_SLEEP("GPIO157_A18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN_SLEEP("GPIO158_C18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN_SLEEP("GPIO159_B19", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN_SLEEP("GPIO160_B20", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN_SLEEP("GPIO165_C21", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
-
/* STM APE pins states */
DB8500_MUX_STATE("stmape_c_1", "stmape",
"stm", "ape_mipi34"),
@@ -561,41 +525,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
* Runtime stuff: make it possible to mux in the SKE keypad
* and bias the pins
*/
- /* ske default state */
- DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
- DB8500_PIN("GPIO153_B17", in_pu, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN("GPIO154_C16", in_pu, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN("GPIO155_C19", in_pu, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN("GPIO156_C17", in_pu, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN("GPIO161_D21", in_pu, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN("GPIO162_D20", in_pu, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN("GPIO163_C20", in_pu, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN("GPIO164_B21", in_pu, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN("GPIO157_A18", out_lo, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN("GPIO158_C18", out_lo, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN("GPIO159_B19", out_lo, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN("GPIO160_B20", out_lo, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN("GPIO165_C21", out_lo, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN("GPIO166_A22", out_lo, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN("GPIO167_B24", out_lo, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN("GPIO168_C22", out_lo, "nmk-ske-keypad"), /* O0 */
- /* ske sleep state */
- DB8500_PIN_SLEEP("GPIO153_B17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN_SLEEP("GPIO154_C16", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN_SLEEP("GPIO155_C19", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN_SLEEP("GPIO156_C17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN_SLEEP("GPIO161_D21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN_SLEEP("GPIO162_D20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN_SLEEP("GPIO163_C20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN_SLEEP("GPIO164_B21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN_SLEEP("GPIO157_A18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN_SLEEP("GPIO158_C18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN_SLEEP("GPIO159_B19", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN_SLEEP("GPIO160_B20", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN_SLEEP("GPIO165_C21", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
};
/*
@@ -655,22 +584,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
- /*
- * SKE keyboard partly on alt A and partly on "Other alt C1"
- * Driver KP_O1,2,3,6,7 low and pull up KP_I 0,2,3 for three
- * rows of 6 keys, then pull up force sensing interrup and
- * drive reset and force sensing WU low.
- */
- DB8500_MUX_HOG("kp_a_1", "kp"),
- DB8500_MUX_HOG("kp_oc1_1", "kp"),
- DB8500_PIN_HOG("GPIO90_A3", out_lo), /* KP_O1 */
- DB8500_PIN_HOG("GPIO87_B3", out_lo), /* KP_O2 */
- DB8500_PIN_HOG("GPIO86_C6", out_lo), /* KP_O3 */
- DB8500_PIN_HOG("GPIO96_D8", out_lo), /* KP_O6 */
- DB8500_PIN_HOG("GPIO94_D7", out_lo), /* KP_O7 */
- DB8500_PIN_HOG("GPIO93_B7", in_pu), /* KP_I0 */
- DB8500_PIN_HOG("GPIO89_E6", in_pu), /* KP_I2 */
- DB8500_PIN_HOG("GPIO88_C4", in_pu), /* KP_I3 */
DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */
DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */
DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 11/21] ARM: ux500: drop STM pinmap settings
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
The pin mappings for the STM (System Trace Macrocell) are not
really used by anything: we have no driver for is and the settings
are not connected to any device. We can recreate the different
mux outputs in the device tree the day we need them. Drop these
for now.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/mach-ux500/board-mop500-pins.c | 200 --------------------------------
1 file changed, 200 deletions(-)
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 07ddb89a6dbe..c311d11d6c3d 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -27,7 +27,6 @@ static enum custom_pin_cfg_t pinsfor;
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
-BIAS(in_nopull, PIN_INPUT_NOPULL);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(out_lo, PIN_OUTPUT_LOW);
@@ -43,15 +42,6 @@ BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM
BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
-/* Sleep modes */
-BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
@@ -321,190 +311,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-/* Pin control settings */
-static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /* STM APE pins states */
- DB8500_MUX_STATE("stmape_c_1", "stmape",
- "stm", "ape_mipi34"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "ape_mipi34"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "ape_mipi34"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "ape_mipi34"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "ape_mipi34"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "ape_mipi34"), /* dat0 */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat0 */
-
- DB8500_MUX_STATE("stmape_oc1_1", "stmape",
- "stm", "ape_microsd"),
- DB8500_PIN_STATE("GPIO23_AA4", in_nopull,
- "stm", "ape_microsd"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", in_nopull,
- "stm", "ape_microsd"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", in_nopull,
- "stm", "ape_microsd"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", in_nopull,
- "stm", "ape_microsd"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", in_nopull,
- "stm", "ape_microsd"), /* dat3 */
-
- DB8500_PIN_STATE("GPIO23_AA4", slpm_out_lo_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat3 */
-
- /* STM Modem pins states */
- DB8500_MUX_STATE("stmmod_oc3_2", "stmmod",
- "stm", "mod_mipi34"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_mipi34"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_mipi34"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "mod_mipi34"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "mod_mipi34"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "mod_mipi34"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "mod_mipi34"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "mod_mipi34"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_mipi34"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_mipi34"), /* uartmod tx */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_mipi34_sleep"), /* uartmod tx */
-
- DB8500_MUX_STATE("stmmod_b_1", "stmmod",
- "stm", "mod_microsd"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_microsd"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_microsd"),
- DB8500_PIN_STATE("GPIO23_AA4", in_nopull,
- "stm", "mod_microsd"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", in_nopull,
- "stm", "mod_microsd"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", in_nopull,
- "stm", "mod_microsd"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", in_nopull,
- "stm", "mod_microsd"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", in_nopull,
- "stm", "mod_microsd"), /* dat3 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_microsd"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_microsd"), /* uartmod tx */
-
- DB8500_PIN_STATE("GPIO23_AA4", slpm_out_lo_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* uartmod tx */
-
- /* STM dual Modem/APE pins state */
- DB8500_MUX_STATE("stmmod_oc3_2", "stmmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("stmape_c_2", "stmape",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_mipi34_ape_mipi60"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_mipi34_ape_mipi60"), /* uartmod tx */
- DB8500_PIN_STATE("GPIO155_C19", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* clk */
- DB8500_PIN_STATE("GPIO156_C17", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat3 */
- DB8500_PIN_STATE("GPIO157_A18", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat2 */
- DB8500_PIN_STATE("GPIO158_C18", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat1 */
- DB8500_PIN_STATE("GPIO159_B19", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat0 */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* uartmod tx */
- DB8500_PIN_STATE("GPIO155_C19", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO156_C17", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO157_A18", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO158_C18", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO159_B19", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat0 */
-};
-
/*
* These are specifically for the MOP500 and HREFP (pre-v60) version of the
* board, which utilized a TC35892 GPIO expander instead of using a lot of
@@ -690,8 +496,6 @@ static void __init mop500_href_family_pinmaps_init(void)
void __init mop500_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
pinctrl_register_mappings(mop500_pinmap,
ARRAY_SIZE(mop500_pinmap));
mop500_href_family_pinmaps_init();
@@ -705,8 +509,6 @@ void __init mop500_pinmaps_init(void)
void __init snowball_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
pinctrl_register_mappings(snowball_pinmap,
ARRAY_SIZE(snowball_pinmap));
pinctrl_register_mappings(u8500_pinmap,
@@ -717,8 +519,6 @@ void __init snowball_pinmaps_init(void)
void __init hrefv60_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
pinctrl_register_mappings(hrefv60_pinmap,
ARRAY_SIZE(hrefv60_pinmap));
mop500_href_family_pinmaps_init();
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 11/21] ARM: ux500: drop STM pinmap settings
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
The pin mappings for the STM (System Trace Macrocell) are not
really used by anything: we have no driver for is and the settings
are not connected to any device. We can recreate the different
mux outputs in the device tree the day we need them. Drop these
for now.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/mach-ux500/board-mop500-pins.c | 200 --------------------------------
1 file changed, 200 deletions(-)
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 07ddb89a6dbe..c311d11d6c3d 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -27,7 +27,6 @@ static enum custom_pin_cfg_t pinsfor;
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
-BIAS(in_nopull, PIN_INPUT_NOPULL);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(out_lo, PIN_OUTPUT_LOW);
@@ -43,15 +42,6 @@ BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM
BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
-/* Sleep modes */
-BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
@@ -321,190 +311,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-/* Pin control settings */
-static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /* STM APE pins states */
- DB8500_MUX_STATE("stmape_c_1", "stmape",
- "stm", "ape_mipi34"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "ape_mipi34"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "ape_mipi34"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "ape_mipi34"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "ape_mipi34"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "ape_mipi34"), /* dat0 */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat0 */
-
- DB8500_MUX_STATE("stmape_oc1_1", "stmape",
- "stm", "ape_microsd"),
- DB8500_PIN_STATE("GPIO23_AA4", in_nopull,
- "stm", "ape_microsd"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", in_nopull,
- "stm", "ape_microsd"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", in_nopull,
- "stm", "ape_microsd"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", in_nopull,
- "stm", "ape_microsd"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", in_nopull,
- "stm", "ape_microsd"), /* dat3 */
-
- DB8500_PIN_STATE("GPIO23_AA4", slpm_out_lo_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat3 */
-
- /* STM Modem pins states */
- DB8500_MUX_STATE("stmmod_oc3_2", "stmmod",
- "stm", "mod_mipi34"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_mipi34"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_mipi34"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "mod_mipi34"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "mod_mipi34"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "mod_mipi34"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "mod_mipi34"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "mod_mipi34"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_mipi34"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_mipi34"), /* uartmod tx */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_mipi34_sleep"), /* uartmod tx */
-
- DB8500_MUX_STATE("stmmod_b_1", "stmmod",
- "stm", "mod_microsd"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_microsd"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_microsd"),
- DB8500_PIN_STATE("GPIO23_AA4", in_nopull,
- "stm", "mod_microsd"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", in_nopull,
- "stm", "mod_microsd"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", in_nopull,
- "stm", "mod_microsd"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", in_nopull,
- "stm", "mod_microsd"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", in_nopull,
- "stm", "mod_microsd"), /* dat3 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_microsd"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_microsd"), /* uartmod tx */
-
- DB8500_PIN_STATE("GPIO23_AA4", slpm_out_lo_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* uartmod tx */
-
- /* STM dual Modem/APE pins state */
- DB8500_MUX_STATE("stmmod_oc3_2", "stmmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("stmape_c_2", "stmape",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_mipi34_ape_mipi60"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_mipi34_ape_mipi60"), /* uartmod tx */
- DB8500_PIN_STATE("GPIO155_C19", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* clk */
- DB8500_PIN_STATE("GPIO156_C17", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat3 */
- DB8500_PIN_STATE("GPIO157_A18", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat2 */
- DB8500_PIN_STATE("GPIO158_C18", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat1 */
- DB8500_PIN_STATE("GPIO159_B19", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat0 */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* uartmod tx */
- DB8500_PIN_STATE("GPIO155_C19", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO156_C17", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO157_A18", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO158_C18", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO159_B19", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat0 */
-};
-
/*
* These are specifically for the MOP500 and HREFP (pre-v60) version of the
* board, which utilized a TC35892 GPIO expander instead of using a lot of
@@ -690,8 +496,6 @@ static void __init mop500_href_family_pinmaps_init(void)
void __init mop500_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
pinctrl_register_mappings(mop500_pinmap,
ARRAY_SIZE(mop500_pinmap));
mop500_href_family_pinmaps_init();
@@ -705,8 +509,6 @@ void __init mop500_pinmaps_init(void)
void __init snowball_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
pinctrl_register_mappings(snowball_pinmap,
ARRAY_SIZE(snowball_pinmap));
pinctrl_register_mappings(u8500_pinmap,
@@ -717,8 +519,6 @@ void __init snowball_pinmaps_init(void)
void __init hrefv60_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
pinctrl_register_mappings(hrefv60_pinmap,
ARRAY_SIZE(hrefv60_pinmap));
mop500_href_family_pinmaps_init();
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 12/21] ARM: ux500: move old HREF ipgpio to the device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-hrefprev60.dtsi | 16 ++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 24 ------------------------
2 files changed, 16 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 32295e396ff8..b0f5def8e2a8 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -68,6 +68,10 @@
};
pinctrl {
+ /* Set this up using hogs */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefprev60_mode>;
+
ssp0 {
ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
hrefprev60_mux {
@@ -103,6 +107,18 @@
};
};
};
+ ipgpio {
+ ipgpio_hrefprev60_mode: ipgpio_hrefprev60 {
+ hrefprev60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index c311d11d6c3d..257c97a214a5 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -312,28 +312,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
};
/*
- * These are specifically for the MOP500 and HREFP (pre-v60) version of the
- * board, which utilized a TC35892 GPIO expander instead of using a lot of
- * on-chip pins as the HREFv60 and later does.
- */
-static struct pinctrl_map __initdata mop500_pinmap[] = {
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID) and 1 (XENON_READY) on altfunction C and pull up
- * the pins.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu),
- DB8500_PIN_HOG("GPIO7_AG5", in_pu),
- /*
- * Runtime stuff: make it possible to mux in the SKE keypad
- * and bias the pins
- */
-};
-
-/*
* The HREFv60 series of platforms is using available pins on the DB8500
* insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
@@ -496,8 +474,6 @@ static void __init mop500_href_family_pinmaps_init(void)
void __init mop500_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_pinmap,
- ARRAY_SIZE(mop500_pinmap));
mop500_href_family_pinmaps_init();
if (machine_is_u8520())
pinctrl_register_mappings(ab8505_pinmap,
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 12/21] ARM: ux500: move old HREF ipgpio to the device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-hrefprev60.dtsi | 16 ++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 24 ------------------------
2 files changed, 16 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 32295e396ff8..b0f5def8e2a8 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -68,6 +68,10 @@
};
pinctrl {
+ /* Set this up using hogs */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefprev60_mode>;
+
ssp0 {
ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
hrefprev60_mux {
@@ -103,6 +107,18 @@
};
};
};
+ ipgpio {
+ ipgpio_hrefprev60_mode: ipgpio_hrefprev60 {
+ hrefprev60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index c311d11d6c3d..257c97a214a5 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -312,28 +312,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
};
/*
- * These are specifically for the MOP500 and HREFP (pre-v60) version of the
- * board, which utilized a TC35892 GPIO expander instead of using a lot of
- * on-chip pins as the HREFv60 and later does.
- */
-static struct pinctrl_map __initdata mop500_pinmap[] = {
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID) and 1 (XENON_READY) on altfunction C and pull up
- * the pins.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu),
- DB8500_PIN_HOG("GPIO7_AG5", in_pu),
- /*
- * Runtime stuff: make it possible to mux in the SKE keypad
- * and bias the pins
- */
-};
-
-/*
* The HREFv60 series of platforms is using available pins on the DB8500
* insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
@@ -496,8 +474,6 @@ static void __init mop500_href_family_pinmaps_init(void)
void __init mop500_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_pinmap,
- ARRAY_SIZE(mop500_pinmap));
mop500_href_family_pinmaps_init();
if (machine_is_u8520())
pinctrl_register_mappings(ab8505_pinmap,
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 13/21] ARM: ux500: move GPIO key configuration to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-stuib.dtsi | 41 ++++++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 38 +++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 11 --------
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 6 -----
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 5 ++++
arch/arm/mach-ux500/board-mop500-pins.c | 8 ------
6 files changed, 84 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi
index 76704ec0ffcc..1c3574435ea8 100644
--- a/arch/arm/boot/dts/ste-href-stuib.dtsi
+++ b/arch/arm/boot/dts/ste-href-stuib.dtsi
@@ -12,6 +12,28 @@
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_stuib_mode>, <&hall_stuib_mode>;
+
+ button@139 {
+ /* Proximity sensor */
+ gpios = <&gpio6 25 0x4>;
+ linux,code = <11>; /* SW_FRONT_PROXIMITY */
+ label = "SFH7741 Proximity Sensor";
+ };
+ button@145 {
+ /* Hall sensor */
+ gpios = <&gpio4 17 0x4>;
+ linux,code = <0>; /* SW_LID */
+ label = "HED54XXU11 Hall Effect Sensor";
+ };
+ };
+
soc {
i2c@80004000 {
stmpe1601: stmpe1601@40 {
@@ -74,5 +96,24 @@
rohm,flip-y;
};
};
+
+ pinctrl {
+ prox {
+ prox_stuib_mode: prox_stuib {
+ stuib_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ hall {
+ hall_stuib_mode: stuib_tvk {
+ stuib_cfg {
+ ste,pins = "GPIO145_C13";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 3f31f9206fb3..c40565320978 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -14,6 +14,28 @@
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
+
+ button@139 {
+ /* Proximity sensor */
+ gpios = <&gpio6 25 0x4>;
+ linux,code = <11>; /* SW_FRONT_PROXIMITY */
+ label = "SFH7741 Proximity Sensor";
+ };
+ button@145 {
+ /* Hall sensor */
+ gpios = <&gpio4 17 0x4>;
+ linux,code = <0>; /* SW_LID */
+ label = "HED54XXU11 Hall Effect Sensor";
+ };
+ };
+
soc {
/* Add Synaptics touch screen, TC35893 keypad etc here */
i2c@80004000 {
@@ -76,6 +98,22 @@
};
};
};
+ prox {
+ prox_tvk_mode: prox_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ hall {
+ hall_tvk_mode: hall_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO145_C13";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 56772c3ebb28..e28242173d18 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -18,17 +18,6 @@
reg = <0x00000000 0x20000000>;
};
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
-
- button@1 {
- linux,code = <11>;
- label = "SFH7741 Proximity Sensor";
- };
- };
-
soc {
usb_per5@a03e0000 {
pinctrl-names = "default", "sleep";
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 452f00c4f7c0..6e0105d2f461 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -16,12 +16,6 @@
model = "ST-Ericsson HREF (v60+) platform with Device Tree";
compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
- gpio_keys {
- button@1 {
- gpios = <&gpio5 25 0x4>;
- };
- };
-
soc {
// External Micro SD slot
sdi0_per1@80126000 {
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index ee143b0a5baa..e6f22b266420 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -36,6 +36,11 @@
ste,input = <INPUT_PULLUP>;
};
+ gpio_in_pd: gpio_input_pull_down {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,input = <INPUT_PULLDOWN>;
+ };
+
gpio_out_lo: gpio_output_low {
ste,gpio = <GPIOMODE_ENABLED>;
ste,output = <OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 257c97a214a5..4535702a8e3f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -382,14 +382,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
/* Accelerometer interrupt lines */
DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
- /*
- * Runtime stuff
- * Pull up/down of some sensor GPIO pins, for proximity, HAL sensor
- * etc.
- */
- DB8500_PIN("GPIO217_AH12", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
- DB8500_PIN("GPIO145_C13", gpio_in_pd_slpm_gpio_nopull, "gpio-keys.0"),
- DB8500_PIN("GPIO139_C9", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
};
static struct pinctrl_map __initdata u9500_pinmap[] = {
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 13/21] ARM: ux500: move GPIO key configuration to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-stuib.dtsi | 41 ++++++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 38 +++++++++++++++++++++++++++
arch/arm/boot/dts/ste-href.dtsi | 11 --------
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 6 -----
arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 5 ++++
arch/arm/mach-ux500/board-mop500-pins.c | 8 ------
6 files changed, 84 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi
index 76704ec0ffcc..1c3574435ea8 100644
--- a/arch/arm/boot/dts/ste-href-stuib.dtsi
+++ b/arch/arm/boot/dts/ste-href-stuib.dtsi
@@ -12,6 +12,28 @@
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_stuib_mode>, <&hall_stuib_mode>;
+
+ button at 139 {
+ /* Proximity sensor */
+ gpios = <&gpio6 25 0x4>;
+ linux,code = <11>; /* SW_FRONT_PROXIMITY */
+ label = "SFH7741 Proximity Sensor";
+ };
+ button at 145 {
+ /* Hall sensor */
+ gpios = <&gpio4 17 0x4>;
+ linux,code = <0>; /* SW_LID */
+ label = "HED54XXU11 Hall Effect Sensor";
+ };
+ };
+
soc {
i2c at 80004000 {
stmpe1601: stmpe1601 at 40 {
@@ -74,5 +96,24 @@
rohm,flip-y;
};
};
+
+ pinctrl {
+ prox {
+ prox_stuib_mode: prox_stuib {
+ stuib_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ hall {
+ hall_stuib_mode: stuib_tvk {
+ stuib_cfg {
+ ste,pins = "GPIO145_C13";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 3f31f9206fb3..c40565320978 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -14,6 +14,28 @@
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
+
+ button at 139 {
+ /* Proximity sensor */
+ gpios = <&gpio6 25 0x4>;
+ linux,code = <11>; /* SW_FRONT_PROXIMITY */
+ label = "SFH7741 Proximity Sensor";
+ };
+ button at 145 {
+ /* Hall sensor */
+ gpios = <&gpio4 17 0x4>;
+ linux,code = <0>; /* SW_LID */
+ label = "HED54XXU11 Hall Effect Sensor";
+ };
+ };
+
soc {
/* Add Synaptics touch screen, TC35893 keypad etc here */
i2c at 80004000 {
@@ -76,6 +98,22 @@
};
};
};
+ prox {
+ prox_tvk_mode: prox_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ hall {
+ hall_tvk_mode: hall_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO145_C13";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 56772c3ebb28..e28242173d18 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -18,17 +18,6 @@
reg = <0x00000000 0x20000000>;
};
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
-
- button at 1 {
- linux,code = <11>;
- label = "SFH7741 Proximity Sensor";
- };
- };
-
soc {
usb_per5 at a03e0000 {
pinctrl-names = "default", "sleep";
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 452f00c4f7c0..6e0105d2f461 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -16,12 +16,6 @@
model = "ST-Ericsson HREF (v60+) platform with Device Tree";
compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
- gpio_keys {
- button at 1 {
- gpios = <&gpio5 25 0x4>;
- };
- };
-
soc {
// External Micro SD slot
sdi0_per1 at 80126000 {
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
index ee143b0a5baa..e6f22b266420 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
@@ -36,6 +36,11 @@
ste,input = <INPUT_PULLUP>;
};
+ gpio_in_pd: gpio_input_pull_down {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,input = <INPUT_PULLDOWN>;
+ };
+
gpio_out_lo: gpio_output_low {
ste,gpio = <GPIOMODE_ENABLED>;
ste,output = <OUTPUT_LOW>;
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 257c97a214a5..4535702a8e3f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -382,14 +382,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
/* Accelerometer interrupt lines */
DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
- /*
- * Runtime stuff
- * Pull up/down of some sensor GPIO pins, for proximity, HAL sensor
- * etc.
- */
- DB8500_PIN("GPIO217_AH12", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
- DB8500_PIN("GPIO145_C13", gpio_in_pd_slpm_gpio_nopull, "gpio-keys.0"),
- DB8500_PIN("GPIO139_C9", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
};
static struct pinctrl_map __initdata u9500_pinmap[] = {
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 14/21] ARM: ux500: move the WLAN GPIO pin setup to the device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves some of the pin setup related to the CW1200 WLAN
module over to the device tree. As the driver is not yet
activated for the CW1200 WLAN we do not assign this pinctrl
state to any device node yet.
Get rid of the cmdline argument passing of a certain U9500
platform variant, as this is not supported by the kernel or
any device tree.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 19 +++++++
arch/arm/mach-ux500/board-mop500-pins.c | 75 --------------------------
2 files changed, 19 insertions(+), 75 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 854a4a6e521e..addfcc7c2750 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -721,6 +721,25 @@
};
};
};
+
+ wlan {
+ wlan_default_mode: wlan_default {
+ /*
+ * Activate this mode with the WLAN chip.
+ * These are plain GPIO pins used by WLAN
+ */
+ default_cfg1 {
+ ste,pins =
+ "GPIO226_AF8", /* WLAN_PMU_EN */
+ "GPIO85_D5"; /* WLAN_ENA */
+ ste,config = <&gpio_out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 4535702a8e3f..d0d527a3d205 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -16,19 +16,11 @@
#include "board-mop500.h"
-enum custom_pin_cfg_t {
- PINS_FOR_DEFAULT,
- PINS_FOR_U9500,
-};
-
-static enum custom_pin_cfg_t pinsfor;
-
/* These simply sets bias for pins */
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
BIAS(in_pu, PIN_INPUT_PULLUP);
-BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
@@ -38,8 +30,6 @@ BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
/* These also force them into GPIO mode */
BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
-BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
@@ -317,8 +307,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
*/
static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /* Drive WLAN_ENA low */
- DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */
/*
* XENON Flashgun on image processor GPIO (controlled from image
* processor firmware), mux in these image processor GPIO lines 0
@@ -384,27 +372,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
};
-static struct pinctrl_map __initdata u9500_pinmap[] = {
- /* WLAN_IRQ line */
- DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu),
- /* HSI */
- DB8500_MUX_HOG("hsir_a_1", "hsi"),
- DB8500_MUX_HOG("hsit_a_2", "hsi"),
- DB8500_PIN_HOG("GPIO219_AG10", in_pd), /* RX FLA0 */
- DB8500_PIN_HOG("GPIO220_AH10", in_pd), /* RX DAT0 */
- DB8500_PIN_HOG("GPIO221_AJ11", out_lo), /* RX RDY0 */
- DB8500_PIN_HOG("GPIO222_AJ9", out_lo), /* TX FLA0 */
- DB8500_PIN_HOG("GPIO223_AH9", out_lo), /* TX DAT0 */
- DB8500_PIN_HOG("GPIO224_AG9", in_pd), /* TX RDY0 */
- DB8500_PIN_HOG("GPIO225_AG8", in_pd), /* CAWAKE0 */
- DB8500_PIN_HOG("GPIO226_AF8", gpio_out_hi), /* ACWAKE0 */
-};
-
-static struct pinctrl_map __initdata u8500_pinmap[] = {
- DB8500_PIN_HOG("GPIO226_AF8", gpio_out_lo), /* WLAN_PMU_EN */
- DB8500_PIN_HOG("GPIO4_AH6", gpio_in_pu), /* WLAN_IRQ */
-};
-
static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
@@ -426,47 +393,8 @@ static struct pinctrl_map __initdata snowball_pinmap[] = {
DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */
};
-/*
- * passing "pinsfor=" in kernel cmdline allows for custom
- * configuration of GPIOs on u8500 derived boards.
- */
-static int __init early_pinsfor(char *p)
-{
- pinsfor = PINS_FOR_DEFAULT;
-
- if (strcmp(p, "u9500-21") == 0)
- pinsfor = PINS_FOR_U9500;
-
- return 0;
-}
-early_param("pinsfor", early_pinsfor);
-
-int pins_for_u9500(void)
-{
- if (pinsfor == PINS_FOR_U9500)
- return 1;
-
- return 0;
-}
-
-static void __init mop500_href_family_pinmaps_init(void)
-{
- switch (pinsfor) {
- case PINS_FOR_U9500:
- pinctrl_register_mappings(u9500_pinmap,
- ARRAY_SIZE(u9500_pinmap));
- break;
- case PINS_FOR_DEFAULT:
- pinctrl_register_mappings(u8500_pinmap,
- ARRAY_SIZE(u8500_pinmap));
- default:
- break;
- }
-}
-
void __init mop500_pinmaps_init(void)
{
- mop500_href_family_pinmaps_init();
if (machine_is_u8520())
pinctrl_register_mappings(ab8505_pinmap,
ARRAY_SIZE(ab8505_pinmap));
@@ -479,8 +407,6 @@ void __init snowball_pinmaps_init(void)
{
pinctrl_register_mappings(snowball_pinmap,
ARRAY_SIZE(snowball_pinmap));
- pinctrl_register_mappings(u8500_pinmap,
- ARRAY_SIZE(u8500_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
@@ -489,7 +415,6 @@ void __init hrefv60_pinmaps_init(void)
{
pinctrl_register_mappings(hrefv60_pinmap,
ARRAY_SIZE(hrefv60_pinmap));
- mop500_href_family_pinmaps_init();
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 14/21] ARM: ux500: move the WLAN GPIO pin setup to the device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
This moves some of the pin setup related to the CW1200 WLAN
module over to the device tree. As the driver is not yet
activated for the CW1200 WLAN we do not assign this pinctrl
state to any device node yet.
Get rid of the cmdline argument passing of a certain U9500
platform variant, as this is not supported by the kernel or
any device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 19 +++++++
arch/arm/mach-ux500/board-mop500-pins.c | 75 --------------------------
2 files changed, 19 insertions(+), 75 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 854a4a6e521e..addfcc7c2750 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -721,6 +721,25 @@
};
};
};
+
+ wlan {
+ wlan_default_mode: wlan_default {
+ /*
+ * Activate this mode with the WLAN chip.
+ * These are plain GPIO pins used by WLAN
+ */
+ default_cfg1 {
+ ste,pins =
+ "GPIO226_AF8", /* WLAN_PMU_EN */
+ "GPIO85_D5"; /* WLAN_ENA */
+ ste,config = <&gpio_out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 4535702a8e3f..d0d527a3d205 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -16,19 +16,11 @@
#include "board-mop500.h"
-enum custom_pin_cfg_t {
- PINS_FOR_DEFAULT,
- PINS_FOR_U9500,
-};
-
-static enum custom_pin_cfg_t pinsfor;
-
/* These simply sets bias for pins */
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
BIAS(in_pu, PIN_INPUT_PULLUP);
-BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
@@ -38,8 +30,6 @@ BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
/* These also force them into GPIO mode */
BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
-BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
@@ -317,8 +307,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
*/
static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /* Drive WLAN_ENA low */
- DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */
/*
* XENON Flashgun on image processor GPIO (controlled from image
* processor firmware), mux in these image processor GPIO lines 0
@@ -384,27 +372,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
};
-static struct pinctrl_map __initdata u9500_pinmap[] = {
- /* WLAN_IRQ line */
- DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu),
- /* HSI */
- DB8500_MUX_HOG("hsir_a_1", "hsi"),
- DB8500_MUX_HOG("hsit_a_2", "hsi"),
- DB8500_PIN_HOG("GPIO219_AG10", in_pd), /* RX FLA0 */
- DB8500_PIN_HOG("GPIO220_AH10", in_pd), /* RX DAT0 */
- DB8500_PIN_HOG("GPIO221_AJ11", out_lo), /* RX RDY0 */
- DB8500_PIN_HOG("GPIO222_AJ9", out_lo), /* TX FLA0 */
- DB8500_PIN_HOG("GPIO223_AH9", out_lo), /* TX DAT0 */
- DB8500_PIN_HOG("GPIO224_AG9", in_pd), /* TX RDY0 */
- DB8500_PIN_HOG("GPIO225_AG8", in_pd), /* CAWAKE0 */
- DB8500_PIN_HOG("GPIO226_AF8", gpio_out_hi), /* ACWAKE0 */
-};
-
-static struct pinctrl_map __initdata u8500_pinmap[] = {
- DB8500_PIN_HOG("GPIO226_AF8", gpio_out_lo), /* WLAN_PMU_EN */
- DB8500_PIN_HOG("GPIO4_AH6", gpio_in_pu), /* WLAN_IRQ */
-};
-
static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
@@ -426,47 +393,8 @@ static struct pinctrl_map __initdata snowball_pinmap[] = {
DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */
};
-/*
- * passing "pinsfor=" in kernel cmdline allows for custom
- * configuration of GPIOs on u8500 derived boards.
- */
-static int __init early_pinsfor(char *p)
-{
- pinsfor = PINS_FOR_DEFAULT;
-
- if (strcmp(p, "u9500-21") == 0)
- pinsfor = PINS_FOR_U9500;
-
- return 0;
-}
-early_param("pinsfor", early_pinsfor);
-
-int pins_for_u9500(void)
-{
- if (pinsfor == PINS_FOR_U9500)
- return 1;
-
- return 0;
-}
-
-static void __init mop500_href_family_pinmaps_init(void)
-{
- switch (pinsfor) {
- case PINS_FOR_U9500:
- pinctrl_register_mappings(u9500_pinmap,
- ARRAY_SIZE(u9500_pinmap));
- break;
- case PINS_FOR_DEFAULT:
- pinctrl_register_mappings(u8500_pinmap,
- ARRAY_SIZE(u8500_pinmap));
- default:
- break;
- }
-}
-
void __init mop500_pinmaps_init(void)
{
- mop500_href_family_pinmaps_init();
if (machine_is_u8520())
pinctrl_register_mappings(ab8505_pinmap,
ARRAY_SIZE(ab8505_pinmap));
@@ -479,8 +407,6 @@ void __init snowball_pinmaps_init(void)
{
pinctrl_register_mappings(snowball_pinmap,
ARRAY_SIZE(snowball_pinmap));
- pinctrl_register_mappings(u8500_pinmap,
- ARRAY_SIZE(u8500_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
@@ -489,7 +415,6 @@ void __init hrefv60_pinmaps_init(void)
{
pinctrl_register_mappings(hrefv60_pinmap,
ARRAY_SIZE(hrefv60_pinmap));
- mop500_href_family_pinmaps_init();
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 15/21] ARM: ux500: move the HREFv60plus IPGPIO pins to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
Move the control of muxing and enabling the IPGPIO (image
processor GPIO) from the static set-up to the device tree.
Use a hog as we have no device for the flash controller yet.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 31 +++++++++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 16 ----------------
2 files changed, 31 insertions(+), 16 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 6e0105d2f461..ecd26848f24f 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -62,6 +62,10 @@
};
pinctrl {
+ /* Set this up using hogs */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefv60_mode>;
+
sdi0 {
/* SD card detect GPIO pin, extend default state */
sdi0_default_mode: sdi0_default {
@@ -71,6 +75,33 @@
};
};
};
+ ipgpio {
+ /*
+ * XENON Flashgun on image processor GPIO (controlled from image
+ * processor firmware), mux in these image processor GPIO lines 0
+ * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+ * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+ * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+ */
+ ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+ hrefv60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+ };
+ hrefv60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO21_AB3";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg3 {
+ ste,pins = "GPIO64_F3";
+ ste,config = <&out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index d0d527a3d205..e208dddfeda9 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -20,8 +20,6 @@
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
-BIAS(in_pu, PIN_INPUT_PULLUP);
-BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
@@ -307,20 +305,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
*/
static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
- * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
- * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */
- DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */
- DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */
- DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */
/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 15/21] ARM: ux500: move the HREFv60plus IPGPIO pins to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
Move the control of muxing and enabling the IPGPIO (image
processor GPIO) from the static set-up to the device tree.
Use a hog as we have no device for the flash controller yet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 31 +++++++++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 16 ----------------
2 files changed, 31 insertions(+), 16 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 6e0105d2f461..ecd26848f24f 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -62,6 +62,10 @@
};
pinctrl {
+ /* Set this up using hogs */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefv60_mode>;
+
sdi0 {
/* SD card detect GPIO pin, extend default state */
sdi0_default_mode: sdi0_default {
@@ -71,6 +75,33 @@
};
};
};
+ ipgpio {
+ /*
+ * XENON Flashgun on image processor GPIO (controlled from image
+ * processor firmware), mux in these image processor GPIO lines 0
+ * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+ * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+ * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+ */
+ ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+ hrefv60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+ };
+ hrefv60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO21_AB3";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg3 {
+ ste,pins = "GPIO64_F3";
+ ste,config = <&out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index d0d527a3d205..e208dddfeda9 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -20,8 +20,6 @@
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
-BIAS(in_pu, PIN_INPUT_PULLUP);
-BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
@@ -307,20 +305,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
*/
static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
- * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
- * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */
- DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */
- DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */
- DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */
/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 16/21] ARM: ux500: move final HREFv60 LCD pins to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
Put two extra configs into the device tree to handle the default
configuration of the display reset signals on the HREFv60plus,
move this over from the board file to the device tree.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 17 +++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 7 -------
2 files changed, 17 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index ecd26848f24f..25b4848e9a6a 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -102,6 +102,23 @@
};
};
};
+ mcde {
+ lcd_hrefv60_mode: lcd_hrefv60 {
+ /*
+ * Display Interface 1 uses GPIO 65 for RST (reset).
+ * Display Interface 2 uses GPIO 66 for RST (reset).
+ * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+ */
+ hrefv60_cfg1 {
+ ste,pins ="GPIO65_F1";
+ ste,config = <&gpio_out_hi>;
+ };
+ hrefv60_cfg2 {
+ ste,pins ="GPIO66_G3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index e208dddfeda9..6cc71d02957f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -309,13 +309,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
/*
- * Display Interface 1 uses GPIO 65 for RST (reset).
- * Display Interface 2 uses GPIO 66 for RST (reset).
- * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
- */
- DB8500_PIN_HOG("GPIO65_F1", gpio_out_hi), /* DISP1 NO RST */
- DB8500_PIN_HOG("GPIO66_G3", gpio_out_lo), /* DISP2 RST */
- /*
* Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
* GPIO 67 for interrupts. Pull-up the IRQ line and drive both
* reset signals low.
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 16/21] ARM: ux500: move final HREFv60 LCD pins to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
Put two extra configs into the device tree to handle the default
configuration of the display reset signals on the HREFv60plus,
move this over from the board file to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 17 +++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 7 -------
2 files changed, 17 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index ecd26848f24f..25b4848e9a6a 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -102,6 +102,23 @@
};
};
};
+ mcde {
+ lcd_hrefv60_mode: lcd_hrefv60 {
+ /*
+ * Display Interface 1 uses GPIO 65 for RST (reset).
+ * Display Interface 2 uses GPIO 66 for RST (reset).
+ * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+ */
+ hrefv60_cfg1 {
+ ste,pins ="GPIO65_F1";
+ ste,config = <&gpio_out_hi>;
+ };
+ hrefv60_cfg2 {
+ ste,pins ="GPIO66_G3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index e208dddfeda9..6cc71d02957f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -309,13 +309,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = {
DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
/*
- * Display Interface 1 uses GPIO 65 for RST (reset).
- * Display Interface 2 uses GPIO 66 for RST (reset).
- * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
- */
- DB8500_PIN_HOG("GPIO65_F1", gpio_out_hi), /* DISP1 NO RST */
- DB8500_PIN_HOG("GPIO66_G3", gpio_out_lo), /* DISP2 RST */
- /*
* Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
* GPIO 67 for interrupts. Pull-up the IRQ line and drive both
* reset signals low.
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 17/21] ARM: ux500: move HREFv60plus pin configs to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
Move the few remaining HREFv60 pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 155 +++++++++++++++++++++++++++++++-
arch/arm/mach-ux500/board-mop500-pins.c | 53 -----------
2 files changed, 153 insertions(+), 55 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 25b4848e9a6a..941bf9ad6f01 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -62,9 +62,23 @@
};
pinctrl {
- /* Set this up using hogs */
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
pinctrl-names = "default";
- pinctrl-0 = <&ipgpio_hrefv60_mode>;
+ pinctrl-0 = <&ipgpio_hrefv60_mode>,
+ <&accel_hrefv60_mode>,
+ <&magneto_hrefv60_mode>,
+ <&etm_hrefv60_mode>,
+ <&nahj_hrefv60_mode>,
+ <&nfc_hrefv60_mode>,
+ <&force_hrefv60_mode>,
+ <&dipro_hrefv60_mode>,
+ <&vaudio_hf_hrefv60_mode>,
+ <&gbf_hrefv60_mode>,
+ <&hdtv_hrefv60_mode>,
+ <&touch_hrefv60_mode>;
sdi0 {
/* SD card detect GPIO pin, extend default state */
@@ -100,8 +114,145 @@
ste,pins = "GPIO64_F3";
ste,config = <&out_lo>;
};
+ };
+ };
+ accelerometer {
+ accel_hrefv60_mode: accel_hrefv60 {
+ /* Accelerometer interrupt lines 1 & 2 */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO82_C1", "GPIO83_D3";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_hrefv60_mode: magneto_hrefv60 {
+ /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO31_V3";
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO32_V2";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ etm {
+ /*
+ * Drive D19-D23 for the ETM PTM trace interface low,
+ * (presumably pins are unconnected therefore grounded here,
+ * the "other alt C1" setting enables these pins)
+ */
+ etm_hrefv60_mode: etm_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO70_G5",
+ "GPIO71_G4",
+ "GPIO72_H4",
+ "GPIO73_H3",
+ "GPIO74_J3";
+ ste,config = <&gpio_out_lo>;
+ };
};
};
+ nahj {
+ nahj_hrefv60_mode: nahj_hrefv60 {
+ /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO76_J2";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO216_AG12";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ nfc {
+ nfc_hrefv60_mode: nfc_hrefv60 {
+ /* NFC ENA and RESET to low, pulldown IRQ line */
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO77_H1", /* NFC_ENA */
+ "GPIO142_C11"; /* NFC_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO144_B13"; /* NFC_IRQ */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ force {
+ force_hrefv60_mode: force_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins =
+ "GPIO92_D6", /* FORCE_SENSING_RST */
+ "GPIO97_D9"; /* FORCE_SENSING_WU */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ dipro {
+ dipro_hrefv60_mode: dipro_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO139_C9"; /* DIPRO_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ vaudio_hf {
+ vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+ /* Audio Amplifier HF enable GPIO */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ gbf {
+ gbf_hrefv60_mode: gbf_hrefv60 {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ hdtv {
+ hdtv_hrefv60_mode: hdtv_hrefv60 {
+ /* MSP : HDTV INTERFACE GPIO line */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO192_AJ27";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ touch {
+ touch_hrefv60_mode: touch_hrefv60 {
+ /*
+ * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
+ * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
+ * reset signals low.
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO143_D12", "GPIO146_D13";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO67_G2";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
mcde {
lcd_hrefv60_mode: lcd_hrefv60 {
/*
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 6cc71d02957f..71ee944ea70f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -27,7 +27,6 @@ BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
/* These also force them into GPIO mode */
BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
@@ -299,56 +298,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-/*
- * The HREFv60 series of platforms is using available pins on the DB8500
- * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
- * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
- */
-static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
- DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
- DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
- /*
- * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
- * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
- * reset signals low.
- */
- DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */
- DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */
- DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */
- /*
- * Drive D19-D23 for the ETM PTM trace interface low,
- * (presumably pins are unconnected therefore grounded here,
- * the "other alt C1" setting enables these pins)
- */
- DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo),
- DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo),
- DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo),
- DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo),
- DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo),
- /* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */
- DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */
- DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */
- /* NFC ENA and RESET to low, pulldown IRQ line */
- DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
- DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
- DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
- DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */
- DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */
- DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */
- /* DiPro Sensor interrupt */
- DB8500_PIN_HOG("GPIO139_C9", gpio_in_pu), /* DIPRO_INT */
- /* Audio Amplifier HF enable */
- DB8500_PIN_HOG("GPIO149_B14", gpio_out_hi), /* VAUDIO_HF_EN, enable MAX8968 */
- /* GBF interface, pull low to reset state */
- DB8500_PIN_HOG("GPIO171_D23", gpio_out_lo), /* GBF_ENA_RESET */
- /* MSP : HDTV INTERFACE GPIO line */
- DB8500_PIN_HOG("GPIO192_AJ27", gpio_in_pd),
- /* Accelerometer interrupt lines */
- DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
- DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
-};
-
static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
@@ -390,8 +339,6 @@ void __init snowball_pinmaps_init(void)
void __init hrefv60_pinmaps_init(void)
{
- pinctrl_register_mappings(hrefv60_pinmap,
- ARRAY_SIZE(hrefv60_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 17/21] ARM: ux500: move HREFv60plus pin configs to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
Move the few remaining HREFv60 pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-hrefv60plus.dtsi | 155 +++++++++++++++++++++++++++++++-
arch/arm/mach-ux500/board-mop500-pins.c | 53 -----------
2 files changed, 153 insertions(+), 55 deletions(-)
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 25b4848e9a6a..941bf9ad6f01 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -62,9 +62,23 @@
};
pinctrl {
- /* Set this up using hogs */
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
pinctrl-names = "default";
- pinctrl-0 = <&ipgpio_hrefv60_mode>;
+ pinctrl-0 = <&ipgpio_hrefv60_mode>,
+ <&accel_hrefv60_mode>,
+ <&magneto_hrefv60_mode>,
+ <&etm_hrefv60_mode>,
+ <&nahj_hrefv60_mode>,
+ <&nfc_hrefv60_mode>,
+ <&force_hrefv60_mode>,
+ <&dipro_hrefv60_mode>,
+ <&vaudio_hf_hrefv60_mode>,
+ <&gbf_hrefv60_mode>,
+ <&hdtv_hrefv60_mode>,
+ <&touch_hrefv60_mode>;
sdi0 {
/* SD card detect GPIO pin, extend default state */
@@ -100,8 +114,145 @@
ste,pins = "GPIO64_F3";
ste,config = <&out_lo>;
};
+ };
+ };
+ accelerometer {
+ accel_hrefv60_mode: accel_hrefv60 {
+ /* Accelerometer interrupt lines 1 & 2 */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO82_C1", "GPIO83_D3";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_hrefv60_mode: magneto_hrefv60 {
+ /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO31_V3";
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO32_V2";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ etm {
+ /*
+ * Drive D19-D23 for the ETM PTM trace interface low,
+ * (presumably pins are unconnected therefore grounded here,
+ * the "other alt C1" setting enables these pins)
+ */
+ etm_hrefv60_mode: etm_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO70_G5",
+ "GPIO71_G4",
+ "GPIO72_H4",
+ "GPIO73_H3",
+ "GPIO74_J3";
+ ste,config = <&gpio_out_lo>;
+ };
};
};
+ nahj {
+ nahj_hrefv60_mode: nahj_hrefv60 {
+ /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO76_J2";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO216_AG12";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ nfc {
+ nfc_hrefv60_mode: nfc_hrefv60 {
+ /* NFC ENA and RESET to low, pulldown IRQ line */
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO77_H1", /* NFC_ENA */
+ "GPIO142_C11"; /* NFC_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO144_B13"; /* NFC_IRQ */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ force {
+ force_hrefv60_mode: force_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins =
+ "GPIO92_D6", /* FORCE_SENSING_RST */
+ "GPIO97_D9"; /* FORCE_SENSING_WU */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ dipro {
+ dipro_hrefv60_mode: dipro_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO139_C9"; /* DIPRO_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ vaudio_hf {
+ vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+ /* Audio Amplifier HF enable GPIO */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ gbf {
+ gbf_hrefv60_mode: gbf_hrefv60 {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ hdtv {
+ hdtv_hrefv60_mode: hdtv_hrefv60 {
+ /* MSP : HDTV INTERFACE GPIO line */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO192_AJ27";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ touch {
+ touch_hrefv60_mode: touch_hrefv60 {
+ /*
+ * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
+ * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
+ * reset signals low.
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO143_D12", "GPIO146_D13";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO67_G2";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
mcde {
lcd_hrefv60_mode: lcd_hrefv60 {
/*
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 6cc71d02957f..71ee944ea70f 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -27,7 +27,6 @@ BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
/* These also force them into GPIO mode */
BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
@@ -299,56 +298,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-/*
- * The HREFv60 series of platforms is using available pins on the DB8500
- * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
- * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
- */
-static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
- DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
- DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
- /*
- * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
- * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
- * reset signals low.
- */
- DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */
- DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */
- DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */
- /*
- * Drive D19-D23 for the ETM PTM trace interface low,
- * (presumably pins are unconnected therefore grounded here,
- * the "other alt C1" setting enables these pins)
- */
- DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo),
- DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo),
- DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo),
- DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo),
- DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo),
- /* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */
- DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */
- DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */
- /* NFC ENA and RESET to low, pulldown IRQ line */
- DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
- DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
- DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
- DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */
- DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */
- DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */
- /* DiPro Sensor interrupt */
- DB8500_PIN_HOG("GPIO139_C9", gpio_in_pu), /* DIPRO_INT */
- /* Audio Amplifier HF enable */
- DB8500_PIN_HOG("GPIO149_B14", gpio_out_hi), /* VAUDIO_HF_EN, enable MAX8968 */
- /* GBF interface, pull low to reset state */
- DB8500_PIN_HOG("GPIO171_D23", gpio_out_lo), /* GBF_ENA_RESET */
- /* MSP : HDTV INTERFACE GPIO line */
- DB8500_PIN_HOG("GPIO192_AJ27", gpio_in_pd),
- /* Accelerometer interrupt lines */
- DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
- DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
-};
-
static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
@@ -390,8 +339,6 @@ void __init snowball_pinmaps_init(void)
void __init hrefv60_pinmaps_init(void)
{
- pinctrl_register_mappings(hrefv60_pinmap,
- ARRAY_SIZE(hrefv60_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 18/21] ARM: ux500: move snowball ethernet config to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-snowball.dts | 25 +++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 4 ----
2 files changed, 25 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 53febe58a1cb..4f5457a91589 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -130,6 +130,8 @@
interrupt-parent = <&gpio4>;
vdd33a-supply = <&en_3v3_reg>;
vddvario-supply = <&db8500_vape_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_snowball_mode>;
reg-shift = <1>;
reg-io-width = <2>;
@@ -348,6 +350,29 @@
};
pinctrl {
+ ethernet {
+ /*
+ * Mux in "SM" which is used for the
+ * SMSC911x Ethernet adapter
+ */
+ eth_snowball_mode: eth_snowball {
+ snowball_mux {
+ ste,function = "sm";
+ ste,pins = "sm_b_1";
+ };
+ /* LAN IRQ pin */
+ snowball_cfg1 {
+ ste,pins = "GPIO140_B11";
+ ste,config = <&in_nopull>;
+ };
+ /* LAN reset pin */
+ snowball_cfg2 {
+ ste,pins = "GPIO141_C12";
+ ste,config = <&gpio_out_hi>;
+ };
+
+ };
+ };
sdi0 {
sdi0_default_mode: sdi0_default {
snowball_mux {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 71ee944ea70f..55da56e39974 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -302,12 +302,8 @@ static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
DB8500_PIN_HOG("GPIO145_C13", pd),
- /* Mux in "SM" which is used for the SMSC911x Ethernet adapter */
- DB8500_MUX_HOG("sm_b_1", "sm"),
/* User LED */
DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
- /* Drive RSTn_LAN high */
- DB8500_PIN_HOG("GPIO141_C12", gpio_out_hi),
/* Accelerometer/Magnetometer */
DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 18/21] ARM: ux500: move snowball ethernet config to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-snowball.dts | 25 +++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 4 ----
2 files changed, 25 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 53febe58a1cb..4f5457a91589 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -130,6 +130,8 @@
interrupt-parent = <&gpio4>;
vdd33a-supply = <&en_3v3_reg>;
vddvario-supply = <&db8500_vape_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_snowball_mode>;
reg-shift = <1>;
reg-io-width = <2>;
@@ -348,6 +350,29 @@
};
pinctrl {
+ ethernet {
+ /*
+ * Mux in "SM" which is used for the
+ * SMSC911x Ethernet adapter
+ */
+ eth_snowball_mode: eth_snowball {
+ snowball_mux {
+ ste,function = "sm";
+ ste,pins = "sm_b_1";
+ };
+ /* LAN IRQ pin */
+ snowball_cfg1 {
+ ste,pins = "GPIO140_B11";
+ ste,config = <&in_nopull>;
+ };
+ /* LAN reset pin */
+ snowball_cfg2 {
+ ste,pins = "GPIO141_C12";
+ ste,config = <&gpio_out_hi>;
+ };
+
+ };
+ };
sdi0 {
sdi0_default_mode: sdi0_default {
snowball_mux {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 71ee944ea70f..55da56e39974 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -302,12 +302,8 @@ static struct pinctrl_map __initdata snowball_pinmap[] = {
/* Mux in SSP0 connected to AB8500, pull down RXD pin */
DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
DB8500_PIN_HOG("GPIO145_C13", pd),
- /* Mux in "SM" which is used for the SMSC911x Ethernet adapter */
- DB8500_MUX_HOG("sm_b_1", "sm"),
/* User LED */
DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
- /* Drive RSTn_LAN high */
- DB8500_PIN_HOG("GPIO141_C12", gpio_out_hi),
/* Accelerometer/Magnetometer */
DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 19/21] ARM: ux500: convert Snowball SPI pin reference
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
The SPI0 block is not at all connected to the AB8500 on the
Snowball: it is connected to the external header. These pins
on the header may also be used for GPIO, but let's assume
that SPI is a probable usecase on the Snowball and mux in the
SPI block and use these for SPI.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-snowball.dts | 28 ++++++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 5 -----
2 files changed, 28 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 4f5457a91589..744ab956059a 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -248,6 +248,11 @@
pinctrl-1 = <&i2c3_sleep_mode>;
};
+ ssp@80002000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_snowball_mode>;
+ };
+
cpufreq-cooling {
status = "okay";
};
@@ -386,6 +391,29 @@
};
};
+ ssp0 {
+ ssp0_snowball_mode: ssp0_snowball_default {
+ snowball_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ snowball_cfg1 {
+ ste,pins = "GPIO144_B13"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ snowball_cfg2 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ snowball_cfg3 {
+ ste,pins =
+ "GPIO146_D13", /* TXD */
+ "GPIO143_D12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+
+ };
+ };
};
mcde@a0350000 {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 55da56e39974..0e5d2684bc9a 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -19,8 +19,6 @@
/* These simply sets bias for pins */
#define BIAS(a,b) static unsigned long a[] = { b }
-BIAS(pd, PIN_PULL_DOWN);
-
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
@@ -299,9 +297,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
};
static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* Mux in SSP0 connected to AB8500, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
/* User LED */
DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
/* Accelerometer/Magnetometer */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 19/21] ARM: ux500: convert Snowball SPI pin reference
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
The SPI0 block is not at all connected to the AB8500 on the
Snowball: it is connected to the external header. These pins
on the header may also be used for GPIO, but let's assume
that SPI is a probable usecase on the Snowball and mux in the
SPI block and use these for SPI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-snowball.dts | 28 ++++++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 5 -----
2 files changed, 28 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 4f5457a91589..744ab956059a 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -248,6 +248,11 @@
pinctrl-1 = <&i2c3_sleep_mode>;
};
+ ssp at 80002000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_snowball_mode>;
+ };
+
cpufreq-cooling {
status = "okay";
};
@@ -386,6 +391,29 @@
};
};
+ ssp0 {
+ ssp0_snowball_mode: ssp0_snowball_default {
+ snowball_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ snowball_cfg1 {
+ ste,pins = "GPIO144_B13"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ snowball_cfg2 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ snowball_cfg3 {
+ ste,pins =
+ "GPIO146_D13", /* TXD */
+ "GPIO143_D12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+
+ };
+ };
};
mcde at a0350000 {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 55da56e39974..0e5d2684bc9a 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -19,8 +19,6 @@
/* These simply sets bias for pins */
#define BIAS(a,b) static unsigned long a[] = { b }
-BIAS(pd, PIN_PULL_DOWN);
-
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
@@ -299,9 +297,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
};
static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* Mux in SSP0 connected to AB8500, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
/* User LED */
DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
/* Accelerometer/Magnetometer */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 20/21] ARM: ux500: move snowball LED pin control to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
This moves the Snowball LED pin config to the device tree.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-snowball.dts | 11 +++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 2 --
2 files changed, 11 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 744ab956059a..605188ba30cd 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -76,6 +76,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpioled_snowball_mode>;
used-led {
label = "user_led";
gpios = <&gpio4 14 0x4>;
@@ -414,6 +416,15 @@
};
};
+ gpio_led {
+ gpioled_snowball_mode: gpioled_default {
+ snowball_cfg1 {
+ ste,pins = "GPIO142_C11";
+ ste,config = <&gpio_out_hi>;
+ };
+
+ };
+ };
};
mcde@a0350000 {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 0e5d2684bc9a..aae9cfcfd56a 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -297,8 +297,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
};
static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* User LED */
- DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
/* Accelerometer/Magnetometer */
DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 20/21] ARM: ux500: move snowball LED pin control to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
This moves the Snowball LED pin config to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-snowball.dts | 11 +++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 2 --
2 files changed, 11 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 744ab956059a..605188ba30cd 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -76,6 +76,8 @@
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpioled_snowball_mode>;
used-led {
label = "user_led";
gpios = <&gpio4 14 0x4>;
@@ -414,6 +416,15 @@
};
};
+ gpio_led {
+ gpioled_snowball_mode: gpioled_default {
+ snowball_cfg1 {
+ ste,pins = "GPIO142_C11";
+ ste,config = <&gpio_out_hi>;
+ };
+
+ };
+ };
};
mcde at a0350000 {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 0e5d2684bc9a..aae9cfcfd56a 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -297,8 +297,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
};
static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* User LED */
- DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
/* Accelerometer/Magnetometer */
DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 21/21] ARM: ux500: move snowball pin configs to device tree
2013-11-17 11:03 ` Linus Walleij
@ 2013-11-17 11:04 ` Linus Walleij
-1 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, Linus Walleij
Move the few remaining snowball pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/ste-snowball.dts | 59 +++++++++++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 19 -----------
2 files changed, 59 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 605188ba30cd..9070c3701c89 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -357,6 +357,16 @@
};
pinctrl {
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_snowball_mode>,
+ <&magneto_snowball_mode>,
+ <&gbf_snowball_mode>,
+ <&wlan_snowball_mode>;
+
ethernet {
/*
* Mux in "SM" which is used for the
@@ -425,6 +435,55 @@
};
};
+ accelerometer {
+ accel_snowball_mode: accel_snowball {
+ /* Accelerometer lines */
+ snowball_cfg1 {
+ ste,pins =
+ "GPIO163_C20", /* ACCEL_IRQ1 */
+ "GPIO164_B21"; /* ACCEL_IRQ2 */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_snowball_mode: magneto_snowball {
+ snowball_cfg1 {
+ ste,pins = "GPIO165_C21"; /* MAG_DRDY */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ gbf {
+ gbf_snowball_mode: gbf_snowball {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ snowball_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ wlan {
+ wlan_snowball_mode: wlan_snowball {
+ /*
+ * Activate this mode with the WLAN chip.
+ * These are plain GPIO pins used by WLAN
+ */
+ snowball_cfg1 {
+ ste,pins =
+ "GPIO161_D21", /* WLAN_PMU_EN */
+ "GPIO215_AH13"; /* WLAN_ENA */
+ ste,config = <&gpio_out_lo>;
+ };
+ snowball_cfg2 {
+ ste,pins = "GPIO216_AG12"; /* WLAN_IRQ */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
mcde@a0350000 {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index aae9cfcfd56a..ff532ba30610 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -23,11 +23,6 @@ BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
-/* These also force them into GPIO mode */
-BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
-
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-db8500", group, func)
@@ -296,18 +291,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* Accelerometer/Magnetometer */
- DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
- DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
- DB8500_PIN_HOG("GPIO165_C21", gpio_in_pu), /* MAG_DRDY */
- /* WLAN/GBF */
- DB8500_PIN_HOG("GPIO161_D21", gpio_out_lo), /* WLAN_PMU_EN */
- DB8500_PIN_HOG("GPIO171_D23", gpio_out_hi), /* GBF_ENA */
- DB8500_PIN_HOG("GPIO215_AH13", gpio_out_lo), /* WLAN_ENA */
- DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */
-};
-
void __init mop500_pinmaps_init(void)
{
if (machine_is_u8520())
@@ -320,8 +303,6 @@ void __init mop500_pinmaps_init(void)
void __init snowball_pinmaps_init(void)
{
- pinctrl_register_mappings(snowball_pinmap,
- ARRAY_SIZE(snowball_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCH 21/21] ARM: ux500: move snowball pin configs to device tree
@ 2013-11-17 11:04 ` Linus Walleij
0 siblings, 0 replies; 44+ messages in thread
From: Linus Walleij @ 2013-11-17 11:04 UTC (permalink / raw)
To: linux-arm-kernel
Move the few remaining snowball pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/ste-snowball.dts | 59 +++++++++++++++++++++++++++++++++
arch/arm/mach-ux500/board-mop500-pins.c | 19 -----------
2 files changed, 59 insertions(+), 19 deletions(-)
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 605188ba30cd..9070c3701c89 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -357,6 +357,16 @@
};
pinctrl {
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_snowball_mode>,
+ <&magneto_snowball_mode>,
+ <&gbf_snowball_mode>,
+ <&wlan_snowball_mode>;
+
ethernet {
/*
* Mux in "SM" which is used for the
@@ -425,6 +435,55 @@
};
};
+ accelerometer {
+ accel_snowball_mode: accel_snowball {
+ /* Accelerometer lines */
+ snowball_cfg1 {
+ ste,pins =
+ "GPIO163_C20", /* ACCEL_IRQ1 */
+ "GPIO164_B21"; /* ACCEL_IRQ2 */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_snowball_mode: magneto_snowball {
+ snowball_cfg1 {
+ ste,pins = "GPIO165_C21"; /* MAG_DRDY */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ gbf {
+ gbf_snowball_mode: gbf_snowball {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ snowball_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ wlan {
+ wlan_snowball_mode: wlan_snowball {
+ /*
+ * Activate this mode with the WLAN chip.
+ * These are plain GPIO pins used by WLAN
+ */
+ snowball_cfg1 {
+ ste,pins =
+ "GPIO161_D21", /* WLAN_PMU_EN */
+ "GPIO215_AH13"; /* WLAN_ENA */
+ ste,config = <&gpio_out_lo>;
+ };
+ snowball_cfg2 {
+ ste,pins = "GPIO216_AG12"; /* WLAN_IRQ */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
};
mcde at a0350000 {
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index aae9cfcfd56a..ff532ba30610 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -23,11 +23,6 @@ BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
-/* These also force them into GPIO mode */
-BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
-
/* We use these to define hog settings that are always done on boot */
#define DB8500_MUX_HOG(group,func) \
PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-db8500", group, func)
@@ -296,18 +291,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* Accelerometer/Magnetometer */
- DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
- DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
- DB8500_PIN_HOG("GPIO165_C21", gpio_in_pu), /* MAG_DRDY */
- /* WLAN/GBF */
- DB8500_PIN_HOG("GPIO161_D21", gpio_out_lo), /* WLAN_PMU_EN */
- DB8500_PIN_HOG("GPIO171_D23", gpio_out_hi), /* GBF_ENA */
- DB8500_PIN_HOG("GPIO215_AH13", gpio_out_lo), /* WLAN_ENA */
- DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */
-};
-
void __init mop500_pinmaps_init(void)
{
if (machine_is_u8520())
@@ -320,8 +303,6 @@ void __init mop500_pinmaps_init(void)
void __init snowball_pinmaps_init(void)
{
- pinctrl_register_mappings(snowball_pinmap,
- ARRAY_SIZE(snowball_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
--
1.8.3.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
end of thread, other threads:[~2013-11-17 11:04 UTC | newest]
Thread overview: 44+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-11-17 11:03 [PATCH 00/21] ARM: ux500: pin control device tree migration Linus Walleij
2013-11-17 11:03 ` Linus Walleij
[not found] ` <1384686250-10542-1-git-send-email-linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
2013-11-17 11:03 ` [PATCH 01/21] ARM: ux500: move UART pin control to the device tree Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 02/21] ARM: ux500: move I2C " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 03/21] ARM: ux500: move MMC/SD/SDIO " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 04/21] ARM: ux500: move MSP " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 05/21] ARM: ux500: move GPIO217/218 config to " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 06/21] ARM: ux500: move MUSB pin " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 07/21] ARM: ux500: move SPI " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 08/21] ARM: ux500: create MCDE node to collect resources Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 09/21] ARM: ux500: move MCDE pin config to device tree Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:03 ` [PATCH 10/21] ARM: ux500: move SKE " Linus Walleij
2013-11-17 11:03 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 11/21] ARM: ux500: drop STM pinmap settings Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 12/21] ARM: ux500: move old HREF ipgpio to the device tree Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 13/21] ARM: ux500: move GPIO key configuration to " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 14/21] ARM: ux500: move the WLAN GPIO pin setup to the " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 15/21] ARM: ux500: move the HREFv60plus IPGPIO pins to " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 16/21] ARM: ux500: move final HREFv60 LCD " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 17/21] ARM: ux500: move HREFv60plus pin configs " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 18/21] ARM: ux500: move snowball ethernet config " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 19/21] ARM: ux500: convert Snowball SPI pin reference Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 20/21] ARM: ux500: move snowball LED pin control to device tree Linus Walleij
2013-11-17 11:04 ` Linus Walleij
2013-11-17 11:04 ` [PATCH 21/21] ARM: ux500: move snowball pin configs " Linus Walleij
2013-11-17 11:04 ` Linus Walleij
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.