* [BUG] P2P setup timeout
@ 2013-12-06 10:18 David Herrmann
2013-12-09 14:03 ` Oleksij Rempel
` (2 more replies)
0 siblings, 3 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-06 10:18 UTC (permalink / raw)
To: linux-wireless
[-- Attachment #1: Type: text/plain, Size: 5866 bytes --]
Hi
I am currently working on user-space helpers for P2P setup as part of
an Open-Source Miracast implementation (openwfd). I can set up a
P2P-group with my Android test-device just fine, however, it only
works if initiated by the GNU/Linux host. Once I initiate the
p2p-connect from the Android device, it creates a group and sends me a
p2p-invitation which I am unable to accept.
I am running wpa_supplicant-git from today (but also tried older
versions), ath9k-htc from linus-git (3.13-rc2) and the relevant log
files are appended.
My wpa-config is:
ctrl_interface=/var/run/wpa_supplicant
update_config=1
p2p_go_ht40=1
And I do nothing else than open wpa_cli and run:
p2p_find
p2p_connect <peer> pbc
This works perfectly well if I don't touch the Android device before
issuing the p2p_connect. However, if I initiate the first connect on
the Android device, my linux host gets a p2p-invitation:
<3>P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2
go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
I tried accepting this invitation via p2p_connect, but just nothing
happens. I also tried any combination of arguments
(auth/join/persistent, pbc/pin/PIN#, playing with go_intent=), didn't
help..
Looking at the wpa-log, I see a timeout firing repeatedly:
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Below you can see the whole sequence of wpa-messages that repeat over
and over again until I cancel the connection-request.
For WFD I need to initiate the connect from the Android device,
otherwise their WFD stack won't recognize the connection. So if anyone
has hints what might be wrong here, I'd gladly try out any patches or
configurations.
I cannot test whether this happens with other drivers, too, as I
couldn't get my hands on a device other than ath9k-htc which supports
p2p on linux.
If anyone is interested, I'll be presenting OpenWFD at FOSDEM in the
graphics-devroom. It would be awesome if I can get my Nexus-4 as a
working demo until then. Otherwise, it'll be just linux<->linux demos
(non-android), which is already working fine.
Any hints welcome!
David
The repeating log-messages from wpa-supplicant are (see attached file
for the whole log):
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddae00
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on!
nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa7 for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0
duration=204 cookie=0xa7 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0
pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received
for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0
duration=0 cookie=0xa7 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms
pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05
06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2
src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms
no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddb100 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2
src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
wpa_cli log/interaction is this:
wpa_cli v2.1-devel
Copyright (c) 2004-2013, Jouni Malinen <j@w1.fi> and contributors
This software may be distributed under the terms of the BSD license.
See README for more details.
Interactive mode
> p2p_find
OK
<3>P2P-DEVICE-FOUND 12:68:3f:4e:39:f2 p2p_dev_addr=12:68:3f:4e:39:f2
pri_dev_type=10-0050F204-5 name='dvdhrm-nx' config_methods=0x188
dev_capab=0x25 group_capab=0x0
<3>P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2
go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
> p2p_connect 12:68:3f:4e:39:f2 pbc
OK
<3>P2P-FIND-STOPPED
[-- Attachment #2: wpa.log --]
[-- Type: text/x-log, Size: 114688 bytes --]
wpa_supplicant v2.1-devel
Successfully initialized wpa_supplicant
Initializing interface 'wlan1' conf '/home/david/dev/wpa.conf' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/home/david/dev/wpa.conf' -> '/home/david/dev/wpa.conf'
Reading configuration file '/home/david/dev/wpa.conf'
ctrl_interface='/var/run/wpa_supplicant'
update_config=1
p2p_go_ht40=1
rfkill: initial event: idx=0 type=8 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=2 type=2 op=0 soft=0 hard=0
rfkill: initial event: idx=5 type=1 op=0 soft=0 hard=0
nl80211: Using driver-based off-channel TX
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface wlan1 in phy phy3
nl80211: Set mode ifindex 14 iftype 2 (STATION)
nl80211: Subscribe to mgmt frames with non-AP handle 0x23a2b70
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=2): 04 0a
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=2): 04 0b
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=2): 04 0c
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=2): 04 0d
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=6): 04 09 50 6f 9a 09
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=5): 7f 50 6f 9a 09
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=1): 06
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=2): 0a 07
nl80211: Register frame type=0xd0 nl_handle=0x23a2b70
nl80211: Register frame match - hexdump(len=2): 0a 11
netlink: Operstate: linkmode=1, operstate=5
nl80211: driver param='(null)'
Add interface wlan1 to a new radio phy3
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz
nl80211: 2402-2472 @ 20 mBm
nl80211: 2457-2482 @ 40 MHz
nl80211: 2457-2482 @ 20 mBm
nl80211: 2474-2494 @ 20 MHz
nl80211: 2474-2494 @ 20 mBm
nl80211: 5170-5250 @ 80 MHz
nl80211: 5170-5250 @ 20 mBm
nl80211: 5735-5835 @ 80 MHz
nl80211: 5735-5835 @ 20 mBm
nl80211: 57240-63720 @ 2160 MHz
nl80211: 57240-63720 @ 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
wlan1: Own MAC address: 10:6f:3f:7a:7c:24
wpa_driver_nl80211_set_key: ifindex=14 (wlan1) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=14 (wlan1) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=14 (wlan1) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=14 (wlan1) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
wlan1: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
wlan1: State: DISCONNECTED -> INACTIVE
WPS: Set UUID for interface wlan1
WPS: UUID based on MAC address - hexdump(len=16): 8a cf ff df 8a 45 5d ea 84 50 d3 05 74 5f 04 a0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Set supplicant port unauthorized for 00:00:00:00:00:00
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
nl80211: Set supplicant port unauthorized for 00:00:00:00:00:00
EAPOL: Supplicant port status: Unauthorized
nl80211: Set supplicant port unauthorized for 00:00:00:00:00:00
Using existing control interface directory.
ctrl_iface bind(PF_UNIX) failed: Address already in use
ctrl_iface exists, but does not allow connections - assuming it was leftover from forced program termination
Successfully replaced leftover ctrl_iface socket '/var/run/wpa_supplicant/wlan1'
P2P: Own listen channel: 6
P2P: Random operating channel: 81:6
P2P: Add operating class 81
P2P: Channels - hexdump(len=11): 01 02 03 04 05 06 07 08 09 0a 0b
P2P: initialized
P2P: channels: 81:1,2,3,4,5,6,7,8,9,10,11
P2P: cli_channels:
wlan1: Added interface wlan1
wlan1: State: INACTIVE -> DISCONNECTED
wpa_driver_nl80211_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
nl80211: Set supplicant port unauthorized for 00:00:00:00:00:00
CTRL_IFACE monitor attached - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
RX ctrl_iface - hexdump_ascii(len=22):
42 53 53 20 52 41 4e 47 45 3d 41 4c 4c 20 4d 41 BSS RANGE=ALL MA
53 4b 3d 30 78 32 SK=0x2
wlan1: Control interface command 'BSS RANGE=ALL MASK=0x2'
RX ctrl_iface - hexdump_ascii(len=8):
50 32 50 5f 46 49 4e 44 P2P_FIND
wlan1: Control interface command 'P2P_FIND'
P2P: Starting find (type=0)
P2P: Clear timeout (state=IDLE)
P2P: State IDLE -> SEARCH
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 10 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (3 BSSes)
wlan1: BSS: Start scan result update 1
wlan1: BSS: Add new id 0 BSSID 00:18:39:0a:8e:23 SSID 'blockfloete'
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
wlan1: BSS: Add new id 1 BSSID 00:12:bf:ce:21:6d SSID 'Katzenkorb'
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
wlan1: BSS: Add new id 2 BSSID 00:1b:2f:5c:23:e6 SSID 'BART2 WZ'
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
BSS: last_scan_res_used=3/32 last_scan_full=0
P2P: Scan results received (3 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x8e for freq=2437 MHz duration=307
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x8e (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x8e (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (4 BSSes)
wlan1: BSS: Start scan result update 2
BSS: last_scan_res_used=3/32 last_scan_full=0
P2P: Scan results received (4 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Update peer 12:68:3f:4e:39:f2 config_methods 0x0 -> 0x188
P2P: Peer found with Listen frequency 2437 MHz (rx_time=1386323605.158015)
P2P-DEVICE-FOUND 12:68:3f:4e:39:f2 p2p_dev_addr=12:68:3f:4e:39:f2 pri_dev_type=10-0050F204-5 name='dvdhrm-nx' config_methods=0x188 dev_capab=0x25 group_capab=0x0
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x8f for freq=2437 MHz duration=204
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0x8f (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x8f (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (5 BSSes)
wlan1: BSS: Start scan result update 3
wlan1: BSS: Add new id 3 BSSID 20:2b:c1:4b:8f:a4 SSID 'WLAN-8FA406'
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
BSS: last_scan_res_used=4/32 last_scan_full=0
P2P: Scan results received (5 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x90 for freq=2437 MHz duration=307
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x90 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.327200 sec
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-43 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-41 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-44 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-43 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-41 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x90 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (5 BSSes)
wlan1: BSS: Start scan result update 4
BSS: last_scan_res_used=4/32 last_scan_full=0
P2P: Scan results received (5 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323605.418152 last_seen=1386323606.839763)
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x91 for freq=2437 MHz duration=102
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=102 cookie=0x91 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,102400) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.122400 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x91 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 5
wlan1: BSS: Add new id 4 BSSID 00:15:0c:7b:52:ab SSID 'Angelika'
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323605.418032 last_seen=1386323606.839763)
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23c0a80
nl80211: Register frame type=0x40 nl_handle=0x23c0a80
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x92 for freq=2437 MHz duration=102
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=102 cookie=0x92 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,102400) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.122400 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x92 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab48209
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 6
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323605.417965 last_seen=1386323606.839763)
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x93 for freq=2437 MHz duration=204
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0x93 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x93 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 7
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323605.417348 last_seen=1386323606.839763)
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x94 for freq=2437 MHz duration=307
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x94 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.327200 sec
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-42 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-46 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-44 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-43 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-43 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x94 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 8
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323605.418121 last_seen=1386323611.197993)
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x95 for freq=2437 MHz duration=204
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0x95 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x95 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 9
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x96 for freq=2437 MHz duration=102
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=102 cookie=0x96 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,102400) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.122400 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x96 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 10
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x97 for freq=2437 MHz duration=204
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0x97 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x97 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 11
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x98 for freq=2437 MHz duration=204
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0x98 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.224800 sec
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-48 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-39 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-39 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-39 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-39 stype=4 len=217
wlan1: Event RX_MGMT (20) received
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Device Password ID: 0
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 6 length 5
P2P: * Listen Channel: Country DE(0x04) Regulatory Class 81 Channel Number 6
P2P: Reply to P2P Probe Request in Listen state
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: send_mlme - noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 nlmode=2
nl80211: Use last_mgmt_freq=2437
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x98 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 12
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323614.291368 last_seen=1386323615.698848)
P2P: State SEARCH -> SEARCH
P2P: Starting short listen state (state=SEARCH)
WPS: * Version (hardcoded 0x10)
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x99 for freq=2437 MHz duration=307
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x99 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=SEARCH): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x99 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=SEARCH)
nl80211: Disable Probe Request reporting nl_preq=0x888888888ab37c09
P2P: Starting search
WPS: Building WPS IE for Probe Request
WPS: * Version (hardcoded 0x10)
WPS: * Request Type
WPS: * Config Methods (148)
WPS: * UUID-E
WPS: * Primary Device Type
WPS: * RF Bands (3)
WPS: * Association State
WPS: * Configuration Error (0)
WPS: * Device Password ID (0)
WPS: * Device Name
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Listen Channel: Regulatory Class 81 Channel 6
wlan1: nl80211: scan request
nl80211: P2P probe - mask SuppRates
Scan requested (ret=0) - scan timeout 30 seconds
P2P: Running p2p_scan
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan1
wlan1: nl80211: Scan trigger
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-38 stype=13 len=152
wlan1: Event RX_ACTION (21) received
wlan1: Received Action frame: SA=12:68:3f:4e:39:f2 Category=4 DataLen=127 freq=2437 MHz
P2P: RX P2P Public Action from 12:68:3f:4e:39:f2
P2P: Received Invitation Request from 12:68:3f:4e:39:f2 (freq=2437)
P2P: Parsing the received message
P2P: * Dialog Token: 1
P2P: Parsing P2P IE
P2P: Attribute 5 length 2
P2P: * Configuration Timeout
P2P: Attribute 18 length 1
P2P: * Invitation Flags: bitmap 0x1
P2P: Attribute 17 length 5
P2P: * Operating Channel: Country DE(0x04) Regulatory Class 81 Channel Number 9
P2P: Attribute 7 length 6
P2P: * P2P Group BSSID: 12:68:3f:4e:b9:f2
P2P: Attribute 11 length 24
P2P: * Channel List: Country String 'DE(0x04)'
P2P: Attribute 15 length 25
P2P: * P2P Group ID: Device Address 12:68:3f:4e:39:f2
P2P: * P2P Group ID: SSID - hexdump_ascii(len=19):
44 49 52 45 43 54 2d 74 4b 2d 64 76 64 68 72 6d DIRECT-tK-dvdhrm
2d 6e 78 -nx
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Peer country - hexdump_ascii(len=3):
44 45 04 DE_
P2P: Own reg_classes 1 peer reg_classes 2 intersection reg_classes 1
P2P: No forced channel from invitation processing - figure out best one to use
P2P: Own default op_class 81 channel 6
P2P: Peer operating channel preference: 2452 MHz
P2P: Use peer preference op_class 81 channel 9
P2P: Try to reselect channel selection with peer information received; previously selected op_class 81 channel 9
P2P: Using original operating class and channel (op_class 81 channel 9) from intersection
P2P: Selected operating channel - 2452 MHz
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Status: 1
P2P: * Configuration Timeout: GO 0 (*10ms) client 0 (*10ms)
P2P: Delay Action frame TX until p2p_scan completes
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
wlan1: nl80211: New scan results available
wlan1: Event SCAN_RESULTS (3) received
nl80211: Received scan results (6 BSSes)
wlan1: BSS: Start scan result update 13
BSS: last_scan_res_used=5/32 last_scan_full=0
P2P: Scan results received (6 BSS)
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Ignore scan data without P2P Device Info or P2P Device Id
P2P: Parsing WPS IE
P2P: Config Methods (WPS): 0x4388
P2P: Primary Device Type (WPS): 10-0050F204-5
P2P: Parsing P2P IE
P2P: Attribute 2 length 2
P2P: * Device Capability 25 Group Capability 00
P2P: Attribute 13 length 30
P2P: * Device Info: addr 12:68:3f:4e:39:f2 primary device type 10-0050F204-5 device name 'dvdhrm-nx' config methods 0x188
P2P: Do not update peer entry based on old frame (rx_time=1386323614.291028 last_seen=1386323615.698848)
P2P: Send pending Action frame at p2p_scan completion
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=10:6f:3f:7a:7c:24 len=23
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=200 ms no_cck=1)
wlan1: P2P: Station mode scan operation not pending anymore (sta_scan_pending=0 p2p_cb_on_scan_complete=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan1' added
nl80211: if_removed already cleared - ignore event
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88009f42e100 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=8 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=10:6f:3f:7a:7c:24 result=0
P2P: Invitation Response TX callback: success=1
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88009f42e100
P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2 go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
RX ctrl_iface - hexdump_ascii(len=33):
50 32 50 5f 43 4f 4e 4e 45 43 54 20 31 32 3a 36 P2P_CONNECT 12:6
38 3a 33 66 3a 34 65 3a 33 39 3a 66 32 20 70 62 8:3f:4e:39:f2 pb
63 c
wlan1: Control interface command 'P2P_CONNECT 12:68:3f:4e:39:f2 pbc'
wlan1: Determining shared radio frequencies (max len 1)
wlan1: Shared frequencies (len=0): completed iteration
P2P: Setup freqs: freq=0 num_MCC=1 shared_freqs=0
P2P: No current operating channels - try to use a new channel
P2P: Own frequency preference: 0 MHz
P2P: Create a new interface p2p-wlan1-0 for the group
nl80211: Create interface iftype 8 (P2P_CLIENT)
Failed to create interface p2p-wlan1-0: -23 (Too many open files in system)
Try to remove and re-create p2p-wlan1-0
nl80211: Remove interface ifindex=15
nl80211: Create interface iftype 8 (P2P_CLIENT)
nl80211: New interface p2p-wlan1-0 created: ifindex=16
nl80211: Add own interface ifindex 16
nl80211: Set TX rates failed: ret=-100 (Network is down)
nl80211: Allocate new address for P2P group interface
nl80211: Assigned new P2P Interface Address 12:6f:3f:7a:7c:24
P2P: Created pending virtual interface p2p-wlan1-0 addr 12:6f:3f:7a:7c:24
P2P: Request to start group negotiation - peer=12:68:3f:4e:39:f2 GO Intent=7 Intended Interface Address=12:6f:3f:7a:7c:24 wps_method=3 persistent_group=0 pd_before_go_neg=0
P2P: Prepare channel - force_freq=0 pref_freq=0 go=0
P2P: Prepare channel best
P2P: Select pre-configured channel as operating channel preference
P2P: prepared channels: 81:1,2,3,4,5,6,7,8,9,10,11
P2P: after go/cli filter/add: 81:1,2,3,4,5,6,7,8,9,10,11
P2P: Own preference for operation channel: Operating Class 81 Channel 6
P2P: Stopping find
P2P: Clear timeout (state=SEARCH)
P2P-FIND-STOPPED
CTRL_IFACE monitor send - hexdump(len=21): 2f 74 6d 70 2f 77 70 61 5f 63 74 72 6c 5f 32 32 37 30 2d 32 00
P2P: State SEARCH -> IDLE
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State IDLE -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Ignore dellink event for foreign ifindex 15
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
nl80211: Ignore interface down event since interface p2p-wlan1-0 is up
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
nl80211: Ignore interface down event since interface p2p-wlan1-0 is up
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff8800a94df100 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff8800a94df100
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Enable Probe Request reporting nl_preq=0x23bf480
nl80211: Register frame type=0x40 nl_handle=0x23bf480
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Remain-on-channel cookie 0x9a for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x9a (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-87 stype=4 len=132
wlan1: Event RX_MGMT (20) received
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-90 stype=4 len=123
wlan1: Event RX_MGMT (20) received
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-87 stype=4 len=116
wlan1: Event RX_MGMT (20) received
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x9a (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddb200 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddb200
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0x9b for freq=2437 MHz duration=102
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=102 cookie=0x9b (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,102400) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.122400 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x9b (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddab00 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddab00
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0x9c for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x9c (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x9c (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fdda000 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fdda000
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0x9d for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x9d (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x9d (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fdda700 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fdda700
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0x9e for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0x9e (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x9e (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddb900 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddb900
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0x9f for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0x9f (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0x9f (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88009f51f300 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88009f51f300
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa0 for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0xa0 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa0 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fdda900 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fdda900
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa1 for freq=2437 MHz duration=102
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=102 cookie=0xa1 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,102400) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.122400 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa1 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddaf00 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddaf00
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa2 for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0xa2 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa2 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddbe00 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddbe00
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa3 for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0xa3 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa3 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddbf00 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddbf00
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa4 for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0xa4 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa4 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan1
nl80211: RX frame freq=2437 ssi_signal=-59 stype=4 len=66
wlan1: Event RX_MGMT (20) received
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddb500 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddb500
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa5 for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0xa5 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa5 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fdda100 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fdda100
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa6 for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0xa6 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa6 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddae00 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddae00
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa7 for freq=2437 MHz duration=204
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=204 cookie=0xa7 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa7 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddb100 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action frame sequence done notification
nl80211: Cancel TX frame wait: cookie=0xffff88008fddb100
nl80211: wait cancel failed: ret=-2 (No such file or directory)
P2P: State CONNECT -> CONNECT_LISTEN
P2P: Starting short listen state (state=CONNECT_LISTEN)
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
WPS: * UUID-E
P2P: * P2P IE header
P2P: * Capability dev=25 group=00
P2P: * Device Info
nl80211: Probe Request reporting already on! nl_preq=0x888888888ab37c09
nl80211: Remain-on-channel cookie 0xa8 for freq=2437 MHz duration=307
nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0 duration=307 cookie=0xa8 (match))
wlan1: Event REMAIN_ON_CHANNEL (22) received
Off-channel: Send Action callback (without_roc=0 pending_action_tx=(nil))
P2P: Starting Listen timeout(0,307200) on freq=2437 based on callback
P2P: Set timeout (state=CONNECT_LISTEN): 0.327200 sec
nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received for wlan1
nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0 duration=0 cookie=0xa8 (match))
wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms pending_action_tx=(nil))
P2P: Driver ended Listen state (freq=2437)
P2P: Skip stop_listen since not in listen_only state.
P2P: Timeout (state=CONNECT_LISTEN)
P2P: State CONNECT_LISTEN -> CONNECT
P2P: * Dialog Token: 1
P2P: * P2P IE header
P2P: * Capability dev=25 group=08
P2P: * GO Intent: Intent 7 Tie breaker 0
P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
P2P: * Listen Channel: Regulatory Class 81 Channel 6
P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05 06 07 08 09 0a 0b
P2P: * Device Info
P2P: * Operating Channel: Regulatory Class 81 Channel 6
WPS: * Version (hardcoded 0x10)
P2P: WPS IE Device Password ID: 4
P2P: Sending GO Negotiation Request
P2P: State CONNECT -> CONNECT
Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms no_cck=1)
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
nl80211: Frame TX status event
nl80211: Action TX status: cookie=0ffff88008fddb700 (match) (ack=1)
wlan1: Event TX_STATUS (18) received
wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
Off-channel: Delete matching pending action frame
Off-channel: TX status result=0 cb=0x42eaf0
P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2 src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
P2P: GO Negotiation Request TX callback: success=1
P2P: State CONNECT -> CONNECT
P2P: Set timeout (state=CONNECT): 0.500000 sec
P2P: Timeout (state=CONNECT)
Off-channel: Action fr
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [BUG] P2P setup timeout
2013-12-06 10:18 [BUG] P2P setup timeout David Herrmann
@ 2013-12-09 14:03 ` Oleksij Rempel
2013-12-09 14:30 ` David Herrmann
2013-12-16 12:00 ` David Herrmann
2013-12-16 12:36 ` Johannes Berg
2 siblings, 1 reply; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-09 14:03 UTC (permalink / raw)
To: David Herrmann, linux-wireless
Am 06.12.2013 11:18, schrieb David Herrmann:
> Hi
>
> I am currently working on user-space helpers for P2P setup as part of
> an Open-Source Miracast implementation (openwfd). I can set up a
> P2P-group with my Android test-device just fine, however, it only
> works if initiated by the GNU/Linux host. Once I initiate the
> p2p-connect from the Android device, it creates a group and sends me a
> p2p-invitation which I am unable to accept.
>
> I am running wpa_supplicant-git from today (but also tried older
> versions), ath9k-htc from linus-git (3.13-rc2) and the relevant log
> files are appended.
>
> My wpa-config is:
> ctrl_interface=/var/run/wpa_supplicant
> update_config=1
> p2p_go_ht40=1
>
> And I do nothing else than open wpa_cli and run:
> p2p_find
> p2p_connect <peer> pbc
>
> This works perfectly well if I don't touch the Android device before
> issuing the p2p_connect. However, if I initiate the first connect on
> the Android device, my linux host gets a p2p-invitation:
> <3>P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2
> go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
>
> I tried accepting this invitation via p2p_connect, but just nothing
> happens. I also tried any combination of arguments
> (auth/join/persistent, pbc/pin/PIN#, playing with go_intent=), didn't
> help..
>
> Looking at the wpa-log, I see a timeout firing repeatedly:
> P2P: GO Negotiation Request TX callback: success=1
> P2P: State CONNECT -> CONNECT
> P2P: Set timeout (state=CONNECT): 0.500000 sec
> P2P: Timeout (state=CONNECT)
> Below you can see the whole sequence of wpa-messages that repeat over
> and over again until I cancel the connection-request.
>
> For WFD I need to initiate the connect from the Android device,
> otherwise their WFD stack won't recognize the connection. So if anyone
> has hints what might be wrong here, I'd gladly try out any patches or
> configurations.
> I cannot test whether this happens with other drivers, too, as I
> couldn't get my hands on a device other than ath9k-htc which supports
> p2p on linux.
>
> If anyone is interested, I'll be presenting OpenWFD at FOSDEM in the
> graphics-devroom. It would be awesome if I can get my Nexus-4 as a
> working demo until then. Otherwise, it'll be just linux<->linux demos
> (non-android), which is already working fine.
Is it related to your "Atheros AR9280: NULL-deref during P2P setup"
issue? Or it is not reproducible any more?
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-09 14:03 ` Oleksij Rempel
@ 2013-12-09 14:30 ` David Herrmann
0 siblings, 0 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-09 14:30 UTC (permalink / raw)
To: Oleksij Rempel; +Cc: linux-wireless
Hi
On Mon, Dec 9, 2013 at 3:03 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> Am 06.12.2013 11:18, schrieb David Herrmann:
>> Hi
>>
>> I am currently working on user-space helpers for P2P setup as part of
>> an Open-Source Miracast implementation (openwfd). I can set up a
>> P2P-group with my Android test-device just fine, however, it only
>> works if initiated by the GNU/Linux host. Once I initiate the
>> p2p-connect from the Android device, it creates a group and sends me a
>> p2p-invitation which I am unable to accept.
>>
>> I am running wpa_supplicant-git from today (but also tried older
>> versions), ath9k-htc from linus-git (3.13-rc2) and the relevant log
>> files are appended.
>>
>> My wpa-config is:
>> ctrl_interface=/var/run/wpa_supplicant
>> update_config=1
>> p2p_go_ht40=1
>>
>> And I do nothing else than open wpa_cli and run:
>> p2p_find
>> p2p_connect <peer> pbc
>>
>> This works perfectly well if I don't touch the Android device before
>> issuing the p2p_connect. However, if I initiate the first connect on
>> the Android device, my linux host gets a p2p-invitation:
>> <3>P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2
>> go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
>>
>> I tried accepting this invitation via p2p_connect, but just nothing
>> happens. I also tried any combination of arguments
>> (auth/join/persistent, pbc/pin/PIN#, playing with go_intent=), didn't
>> help..
>>
>> Looking at the wpa-log, I see a timeout firing repeatedly:
>> P2P: GO Negotiation Request TX callback: success=1
>> P2P: State CONNECT -> CONNECT
>> P2P: Set timeout (state=CONNECT): 0.500000 sec
>> P2P: Timeout (state=CONNECT)
>> Below you can see the whole sequence of wpa-messages that repeat over
>> and over again until I cancel the connection-request.
>>
>> For WFD I need to initiate the connect from the Android device,
>> otherwise their WFD stack won't recognize the connection. So if anyone
>> has hints what might be wrong here, I'd gladly try out any patches or
>> configurations.
>> I cannot test whether this happens with other drivers, too, as I
>> couldn't get my hands on a device other than ath9k-htc which supports
>> p2p on linux.
>>
>> If anyone is interested, I'll be presenting OpenWFD at FOSDEM in the
>> graphics-devroom. It would be awesome if I can get my Nexus-4 as a
>> working demo until then. Otherwise, it'll be just linux<->linux demos
>> (non-android), which is already working fine.
>
> Is it related to your "Atheros AR9280: NULL-deref during P2P setup"
> issue? Or it is not reproducible any more?
The NULL-deref happens very sporadically. I wasn't able to figure out
how to trigger it reliably. This timeout happens *all* the time. So I
think the NULL deref is not directly related. Btw., I added some debug
statements to the ath9k sources in case the NULL deref happens again.
However, I haven't seen it yet so I kinda get the feeling it's a
timing/locking issue.
Thanks
David
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-06 10:18 [BUG] P2P setup timeout David Herrmann
2013-12-09 14:03 ` Oleksij Rempel
@ 2013-12-16 12:00 ` David Herrmann
2013-12-16 12:36 ` Johannes Berg
2 siblings, 0 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-16 12:00 UTC (permalink / raw)
To: linux-wireless
Hi
Anyone with ideas? Or hints whether it's driver or wpa_supplicant related?
Thanks
David
On Fri, Dec 6, 2013 at 11:18 AM, David Herrmann <dh.herrmann@gmail.com> wrote:
> Hi
>
> I am currently working on user-space helpers for P2P setup as part of
> an Open-Source Miracast implementation (openwfd). I can set up a
> P2P-group with my Android test-device just fine, however, it only
> works if initiated by the GNU/Linux host. Once I initiate the
> p2p-connect from the Android device, it creates a group and sends me a
> p2p-invitation which I am unable to accept.
>
> I am running wpa_supplicant-git from today (but also tried older
> versions), ath9k-htc from linus-git (3.13-rc2) and the relevant log
> files are appended.
>
> My wpa-config is:
> ctrl_interface=/var/run/wpa_supplicant
> update_config=1
> p2p_go_ht40=1
>
> And I do nothing else than open wpa_cli and run:
> p2p_find
> p2p_connect <peer> pbc
>
> This works perfectly well if I don't touch the Android device before
> issuing the p2p_connect. However, if I initiate the first connect on
> the Android device, my linux host gets a p2p-invitation:
> <3>P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2
> go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
>
> I tried accepting this invitation via p2p_connect, but just nothing
> happens. I also tried any combination of arguments
> (auth/join/persistent, pbc/pin/PIN#, playing with go_intent=), didn't
> help..
>
> Looking at the wpa-log, I see a timeout firing repeatedly:
> P2P: GO Negotiation Request TX callback: success=1
> P2P: State CONNECT -> CONNECT
> P2P: Set timeout (state=CONNECT): 0.500000 sec
> P2P: Timeout (state=CONNECT)
> Below you can see the whole sequence of wpa-messages that repeat over
> and over again until I cancel the connection-request.
>
> For WFD I need to initiate the connect from the Android device,
> otherwise their WFD stack won't recognize the connection. So if anyone
> has hints what might be wrong here, I'd gladly try out any patches or
> configurations.
> I cannot test whether this happens with other drivers, too, as I
> couldn't get my hands on a device other than ath9k-htc which supports
> p2p on linux.
>
> If anyone is interested, I'll be presenting OpenWFD at FOSDEM in the
> graphics-devroom. It would be awesome if I can get my Nexus-4 as a
> working demo until then. Otherwise, it'll be just linux<->linux demos
> (non-android), which is already working fine.
>
> Any hints welcome!
> David
>
>
> The repeating log-messages from wpa-supplicant are (see attached file
> for the whole log):
>
> Off-channel: Action frame sequence done notification
> nl80211: Cancel TX frame wait: cookie=0xffff88008fddae00
> nl80211: wait cancel failed: ret=-2 (No such file or directory)
> P2P: State CONNECT -> CONNECT_LISTEN
> P2P: Starting short listen state (state=CONNECT_LISTEN)
> WPS: * Version (hardcoded 0x10)
> P2P: WPS IE Device Password ID: 4
> WPS: * UUID-E
> P2P: * P2P IE header
> P2P: * Capability dev=25 group=00
> P2P: * Device Info
> nl80211: Probe Request reporting already on!
> nl_preq=0x888888888ab37c09
> nl80211: Remain-on-channel cookie 0xa7 for freq=2437 MHz duration=204
> nl80211: Drv Event 55 (NL80211_CMD_REMAIN_ON_CHANNEL) received for wlan1
> nl80211: Remain-on-channel event (cancel=0 freq=2437 channel_type=0
> duration=204 cookie=0xa7 (match))
> wlan1: Event REMAIN_ON_CHANNEL (22) received
> Off-channel: Send Action callback (without_roc=0
> pending_action_tx=(nil))
> P2P: Starting Listen timeout(0,204800) on freq=2437 based on callback
> P2P: Set timeout (state=CONNECT_LISTEN): 0.224800 sec
> nl80211: Drv Event 56 (NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL) received
> for wlan1
> nl80211: Remain-on-channel event (cancel=1 freq=2437 channel_type=0
> duration=0 cookie=0xa7 (match))
> wlan1: Event CANCEL_REMAIN_ON_CHANNEL (23) received
> P2P: Cancel remain-on-channel callback (p2p_long_listen=0 ms
> pending_action_tx=(nil))
> P2P: Driver ended Listen state (freq=2437)
> P2P: Skip stop_listen since not in listen_only state.
> P2P: Timeout (state=CONNECT_LISTEN)
> P2P: State CONNECT_LISTEN -> CONNECT
> P2P: * Dialog Token: 1
> P2P: * P2P IE header
> P2P: * Capability dev=25 group=08
> P2P: * GO Intent: Intent 7 Tie breaker 0
> P2P: * Configuration Timeout: GO 255 (*10ms) client 20 (*10ms)
> P2P: * Listen Channel: Regulatory Class 81 Channel 6
> P2P: * Intended P2P Interface Address 12:6f:3f:7a:7c:24
> P2P: * Channel List - hexdump(len=16): 58 58 04 51 0b 01 02 03 04 05
> 06 07 08 09 0a 0b
> P2P: * Device Info
> P2P: * Operating Channel: Regulatory Class 81 Channel 6
> WPS: * Version (hardcoded 0x10)
> P2P: WPS IE Device Password ID: 4
> P2P: Sending GO Negotiation Request
> P2P: State CONNECT -> CONNECT
> Off-channel: Send action frame: freq=2437 dst=12:68:3f:4e:39:f2
> src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 len=113
> nl80211: Send Action frame (ifindex=14, freq=2437 MHz wait=500 ms
> no_cck=1)
> nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan1
> nl80211: Frame TX status event
> nl80211: Action TX status: cookie=0ffff88008fddb100 (match) (ack=1)
> wlan1: Event TX_STATUS (18) received
> wlan1: EVENT_TX_STATUS dst=12:68:3f:4e:39:f2 type=0 stype=13
> Off-channel: Delete matching pending action frame
> Off-channel: TX status result=0 cb=0x42eaf0
> P2P: Action frame TX callback (state=1 freq=2437 dst=12:68:3f:4e:39:f2
> src=10:6f:3f:7a:7c:24 bssid=12:68:3f:4e:39:f2 result=0
> P2P: GO Negotiation Request TX callback: success=1
> P2P: State CONNECT -> CONNECT
> P2P: Set timeout (state=CONNECT): 0.500000 sec
> P2P: Timeout (state=CONNECT)
> Off-channel: Action frame sequence done notification
>
>
> wpa_cli log/interaction is this:
>
> wpa_cli v2.1-devel
> Copyright (c) 2004-2013, Jouni Malinen <j@w1.fi> and contributors
>
> This software may be distributed under the terms of the BSD license.
> See README for more details.
>
> Interactive mode
>
>> p2p_find
> OK
> <3>P2P-DEVICE-FOUND 12:68:3f:4e:39:f2 p2p_dev_addr=12:68:3f:4e:39:f2
> pri_dev_type=10-0050F204-5 name='dvdhrm-nx' config_methods=0x188
> dev_capab=0x25 group_capab=0x0
> <3>P2P-INVITATION-RECEIVED sa=12:68:3f:4e:39:f2
> go_dev_addr=12:68:3f:4e:39:f2 bssid=12:68:3f:4e:b9:f2 unknown-network
>> p2p_connect 12:68:3f:4e:39:f2 pbc
> OK
> <3>P2P-FIND-STOPPED
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-06 10:18 [BUG] P2P setup timeout David Herrmann
2013-12-09 14:03 ` Oleksij Rempel
2013-12-16 12:00 ` David Herrmann
@ 2013-12-16 12:36 ` Johannes Berg
2013-12-16 13:39 ` David Herrmann
2 siblings, 1 reply; 24+ messages in thread
From: Johannes Berg @ 2013-12-16 12:36 UTC (permalink / raw)
To: David Herrmann; +Cc: linux-wireless
On Fri, 2013-12-06 at 11:18 +0100, David Herrmann wrote:
> Hi
>
> I am currently working on user-space helpers for P2P setup as part of
> an Open-Source Miracast implementation (openwfd). I can set up a
> P2P-group with my Android test-device just fine, however, it only
> works if initiated by the GNU/Linux host. Once I initiate the
> p2p-connect from the Android device, it creates a group and sends me a
> p2p-invitation which I am unable to accept.
>
> I am running wpa_supplicant-git from today (but also tried older
> versions), ath9k-htc from linus-git (3.13-rc2) and the relevant log
> files are appended.
Can you check in a sniffer what the frame bitrates are that go out? This
seems suspicious:
nl80211: Set TX rates failed: ret=-100 (Network is down)
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 12:36 ` Johannes Berg
@ 2013-12-16 13:39 ` David Herrmann
2013-12-16 13:45 ` Johannes Berg
0 siblings, 1 reply; 24+ messages in thread
From: David Herrmann @ 2013-12-16 13:39 UTC (permalink / raw)
To: Johannes Berg; +Cc: linux-wireless
[-- Attachment #1: Type: text/plain, Size: 1363 bytes --]
Hi
On Mon, Dec 16, 2013 at 1:36 PM, Johannes Berg
<johannes@sipsolutions.net> wrote:
> On Fri, 2013-12-06 at 11:18 +0100, David Herrmann wrote:
>> Hi
>>
>> I am currently working on user-space helpers for P2P setup as part of
>> an Open-Source Miracast implementation (openwfd). I can set up a
>> P2P-group with my Android test-device just fine, however, it only
>> works if initiated by the GNU/Linux host. Once I initiate the
>> p2p-connect from the Android device, it creates a group and sends me a
>> p2p-invitation which I am unable to accept.
>>
>> I am running wpa_supplicant-git from today (but also tried older
>> versions), ath9k-htc from linus-git (3.13-rc2) and the relevant log
>> files are appended.
>
> Can you check in a sniffer what the frame bitrates are that go out? This
> seems suspicious:
>
> nl80211: Set TX rates failed: ret=-100 (Network is down)
I looked at the sniffer data and all I see is a huge amount of p2p
probe requests from my local device, the successful p2p-invitation and
invitation response and then lots of go-negotiation requests that
never get any response.
I don't know which information you're interested in specifically, so I
appended the data (I hope I'm allowed to do that?)
Anything else I can try?
The Android device is: 12:68:3f:4e:39:f2
My local device is: 10:6f:3f:7a:7c:24 / Buffalo_7a:7c:24
Thanks
David
[-- Attachment #2: p2p.pcapng --]
[-- Type: application/octet-stream, Size: 59428 bytes --]
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 13:39 ` David Herrmann
@ 2013-12-16 13:45 ` Johannes Berg
2013-12-16 13:51 ` David Herrmann
2013-12-17 5:50 ` Ujjal Roy
0 siblings, 2 replies; 24+ messages in thread
From: Johannes Berg @ 2013-12-16 13:45 UTC (permalink / raw)
To: David Herrmann; +Cc: linux-wireless
On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
> > Can you check in a sniffer what the frame bitrates are that go out? This
> > seems suspicious:
> >
> > nl80211: Set TX rates failed: ret=-100 (Network is down)
>
> I looked at the sniffer data and all I see is a huge amount of p2p
> probe requests from my local device, the successful p2p-invitation and
> invitation response and then lots of go-negotiation requests that
> never get any response.
Right, and I suspect they don't get a response because (as the sniffer
trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
in the P2P spec (must use OFDM).
Thus something is wrong with the TX bitrates stuff, but I can't tell you
where that would be ...
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 13:45 ` Johannes Berg
@ 2013-12-16 13:51 ` David Herrmann
2013-12-16 14:57 ` [ath9k-devel] " Oleksij Rempel
2013-12-17 5:50 ` Ujjal Roy
1 sibling, 1 reply; 24+ messages in thread
From: David Herrmann @ 2013-12-16 13:51 UTC (permalink / raw)
To: Johannes Berg, Oleksij Rempel; +Cc: linux-wireless
Hi
On Mon, Dec 16, 2013 at 2:45 PM, Johannes Berg
<johannes@sipsolutions.net> wrote:
> On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
>
>> > Can you check in a sniffer what the frame bitrates are that go out? This
>> > seems suspicious:
>> >
>> > nl80211: Set TX rates failed: ret=-100 (Network is down)
>>
>> I looked at the sniffer data and all I see is a huge amount of p2p
>> probe requests from my local device, the successful p2p-invitation and
>> invitation response and then lots of go-negotiation requests that
>> never get any response.
>
> Right, and I suspect they don't get a response because (as the sniffer
> trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
> in the P2P spec (must use OFDM).
>
> Thus something is wrong with the TX bitrates stuff, but I can't tell you
> where that would be ...
Ok, I will try hooking into the ath9k driver then and see why setting
TX rates fails. Thanks a lot! Maybe Oleksij has some more ideas on
that.
Thanks
David
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 13:51 ` David Herrmann
@ 2013-12-16 14:57 ` Oleksij Rempel
0 siblings, 0 replies; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-16 14:57 UTC (permalink / raw)
To: David Herrmann, Johannes Berg; +Cc: linux-wireless, ath9k-devel
Am 16.12.2013 14:51, schrieb David Herrmann:
> Hi
>
> On Mon, Dec 16, 2013 at 2:45 PM, Johannes Berg
> <johannes@sipsolutions.net> wrote:
>> On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
>>
>>>> Can you check in a sniffer what the frame bitrates are that go out? This
>>>> seems suspicious:
>>>>
>>>> nl80211: Set TX rates failed: ret=-100 (Network is down)
>>>
>>> I looked at the sniffer data and all I see is a huge amount of p2p
>>> probe requests from my local device, the successful p2p-invitation and
>>> invitation response and then lots of go-negotiation requests that
>>> never get any response.
>>
>> Right, and I suspect they don't get a response because (as the sniffer
>> trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
>> in the P2P spec (must use OFDM).
>>
>> Thus something is wrong with the TX bitrates stuff, but I can't tell you
>> where that would be ...
>
> Ok, I will try hooking into the ath9k driver then and see why setting
> TX rates fails. Thanks a lot! Maybe Oleksij has some more ideas on
> that.
ath9k_htc has it own rate controller insight of firmware. We wont to
move this functionality to the host and use minstreal-rt, but currently
this project is not started and currently there is no clear start time
:( Beside, there are more problems with FWs rate controller.
David, if you need to fix this bug, i would you suggest you to
investigate in firmware. I will help you as match as i can.
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 14:57 ` Oleksij Rempel
0 siblings, 0 replies; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-16 14:57 UTC (permalink / raw)
To: ath9k-devel
Am 16.12.2013 14:51, schrieb David Herrmann:
> Hi
>
> On Mon, Dec 16, 2013 at 2:45 PM, Johannes Berg
> <johannes@sipsolutions.net> wrote:
>> On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
>>
>>>> Can you check in a sniffer what the frame bitrates are that go out? This
>>>> seems suspicious:
>>>>
>>>> nl80211: Set TX rates failed: ret=-100 (Network is down)
>>>
>>> I looked at the sniffer data and all I see is a huge amount of p2p
>>> probe requests from my local device, the successful p2p-invitation and
>>> invitation response and then lots of go-negotiation requests that
>>> never get any response.
>>
>> Right, and I suspect they don't get a response because (as the sniffer
>> trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
>> in the P2P spec (must use OFDM).
>>
>> Thus something is wrong with the TX bitrates stuff, but I can't tell you
>> where that would be ...
>
> Ok, I will try hooking into the ath9k driver then and see why setting
> TX rates fails. Thanks a lot! Maybe Oleksij has some more ideas on
> that.
ath9k_htc has it own rate controller insight of firmware. We wont to
move this functionality to the host and use minstreal-rt, but currently
this project is not started and currently there is no clear start time
:( Beside, there are more problems with FWs rate controller.
David, if you need to fix this bug, i would you suggest you to
investigate in firmware. I will help you as match as i can.
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 14:57 ` [ath9k-devel] " Oleksij Rempel
@ 2013-12-16 15:09 ` David Herrmann
-1 siblings, 0 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-16 15:09 UTC (permalink / raw)
To: Oleksij Rempel; +Cc: Johannes Berg, linux-wireless, ath9k-devel
Hi
On Mon, Dec 16, 2013 at 3:57 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> Am 16.12.2013 14:51, schrieb David Herrmann:
>> Hi
>>
>> On Mon, Dec 16, 2013 at 2:45 PM, Johannes Berg
>> <johannes@sipsolutions.net> wrote:
>>> On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
>>>
>>>>> Can you check in a sniffer what the frame bitrates are that go out? This
>>>>> seems suspicious:
>>>>>
>>>>> nl80211: Set TX rates failed: ret=-100 (Network is down)
>>>>
>>>> I looked at the sniffer data and all I see is a huge amount of p2p
>>>> probe requests from my local device, the successful p2p-invitation and
>>>> invitation response and then lots of go-negotiation requests that
>>>> never get any response.
>>>
>>> Right, and I suspect they don't get a response because (as the sniffer
>>> trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
>>> in the P2P spec (must use OFDM).
>>>
>>> Thus something is wrong with the TX bitrates stuff, but I can't tell you
>>> where that would be ...
>>
>> Ok, I will try hooking into the ath9k driver then and see why setting
>> TX rates fails. Thanks a lot! Maybe Oleksij has some more ideas on
>> that.
>
> ath9k_htc has it own rate controller insight of firmware. We wont to
> move this functionality to the host and use minstreal-rt, but currently
> this project is not started and currently there is no clear start time
> :( Beside, there are more problems with FWs rate controller.
>
> David, if you need to fix this bug, i would you suggest you to
> investigate in firmware. I will help you as match as i can.
Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
net/mac80211/cfg.c: ieee80211_set_bitrate_mask():
if (!ieee80211_sdata_running())
return -ENETDOWN;
I'm not sure what exactly the SDATA_RUNNING flag is for here, so I
cannot tell whether removing this check will fix it. I can give it a
try though. The function seems pretty simple and passive (except if
HW_HAS_RATE_CONTROL is set, which ath9k_htc probably has..).
The wpa_supplicant counter-part is src/drivers/driver_nl80211.c
obviously. The failing call is in:
nl80211_disable_11b_rates(drv, ifidx, 1)
It is called from:
nl80211_create_iface() with iftype==P2P_CLIENT
Which is weird, because according to the kernel sources you need
SDATA_RUNNING set (which is guess is not the case after the iface has
just been created as it mirrors netdev-UP right?). So we either need
to start the iface in wpa_supplicant or remove the flag from the
kernel helper, I guess. I will try some hacks..
@Oleksij, I actually have three ath9k-htc devices so I'd like to get
this working, and the devices are really nice apart from this bug. I
will keep you up to date, but if you have any hints where to continue
digging, lemme know. Until it's fixed, I'll just work on
wired-displays via ethernet instead of wifi-displays..
Thanks
David
^ permalink raw reply [flat|nested] 24+ messages in thread* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 15:09 ` David Herrmann
0 siblings, 0 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-16 15:09 UTC (permalink / raw)
To: ath9k-devel
Hi
On Mon, Dec 16, 2013 at 3:57 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> Am 16.12.2013 14:51, schrieb David Herrmann:
>> Hi
>>
>> On Mon, Dec 16, 2013 at 2:45 PM, Johannes Berg
>> <johannes@sipsolutions.net> wrote:
>>> On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
>>>
>>>>> Can you check in a sniffer what the frame bitrates are that go out? This
>>>>> seems suspicious:
>>>>>
>>>>> nl80211: Set TX rates failed: ret=-100 (Network is down)
>>>>
>>>> I looked at the sniffer data and all I see is a huge amount of p2p
>>>> probe requests from my local device, the successful p2p-invitation and
>>>> invitation response and then lots of go-negotiation requests that
>>>> never get any response.
>>>
>>> Right, and I suspect they don't get a response because (as the sniffer
>>> trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
>>> in the P2P spec (must use OFDM).
>>>
>>> Thus something is wrong with the TX bitrates stuff, but I can't tell you
>>> where that would be ...
>>
>> Ok, I will try hooking into the ath9k driver then and see why setting
>> TX rates fails. Thanks a lot! Maybe Oleksij has some more ideas on
>> that.
>
> ath9k_htc has it own rate controller insight of firmware. We wont to
> move this functionality to the host and use minstreal-rt, but currently
> this project is not started and currently there is no clear start time
> :( Beside, there are more problems with FWs rate controller.
>
> David, if you need to fix this bug, i would you suggest you to
> investigate in firmware. I will help you as match as i can.
Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
net/mac80211/cfg.c: ieee80211_set_bitrate_mask():
if (!ieee80211_sdata_running())
return -ENETDOWN;
I'm not sure what exactly the SDATA_RUNNING flag is for here, so I
cannot tell whether removing this check will fix it. I can give it a
try though. The function seems pretty simple and passive (except if
HW_HAS_RATE_CONTROL is set, which ath9k_htc probably has..).
The wpa_supplicant counter-part is src/drivers/driver_nl80211.c
obviously. The failing call is in:
nl80211_disable_11b_rates(drv, ifidx, 1)
It is called from:
nl80211_create_iface() with iftype==P2P_CLIENT
Which is weird, because according to the kernel sources you need
SDATA_RUNNING set (which is guess is not the case after the iface has
just been created as it mirrors netdev-UP right?). So we either need
to start the iface in wpa_supplicant or remove the flag from the
kernel helper, I guess. I will try some hacks..
@Oleksij, I actually have three ath9k-htc devices so I'd like to get
this working, and the devices are really nice apart from this bug. I
will keep you up to date, but if you have any hints where to continue
digging, lemme know. Until it's fixed, I'll just work on
wired-displays via ethernet instead of wifi-displays..
Thanks
David
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [BUG] P2P setup timeout
2013-12-16 15:09 ` [ath9k-devel] " David Herrmann
@ 2013-12-16 15:15 ` Johannes Berg
-1 siblings, 0 replies; 24+ messages in thread
From: Johannes Berg @ 2013-12-16 15:15 UTC (permalink / raw)
To: David Herrmann; +Cc: Oleksij Rempel, linux-wireless, ath9k-devel
On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
Obviously :)
> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
> this working, and the devices are really nice apart from this bug. I
> will keep you up to date, but if you have any hints where to continue
> digging, lemme know. Until it's fixed, I'll just work on
> wired-displays via ethernet instead of wifi-displays..
Based on what Oleksij said, these issues are likely not even related -
maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
call were to succeed it wouldn't work?
The issue here doesn't seem to be that call anyway, since that call was
for the data frames on the p2p-wlan1-0 interface, but rather seems to be
that ath9k_htc ignores the no-CCK parameter for the NL80211_CMD_FRAME
command (in mac80211, this would be IEEE80211_TX_CTL_NO_CCK_RATE)
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 15:15 ` Johannes Berg
0 siblings, 0 replies; 24+ messages in thread
From: Johannes Berg @ 2013-12-16 15:15 UTC (permalink / raw)
To: ath9k-devel
On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
Obviously :)
> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
> this working, and the devices are really nice apart from this bug. I
> will keep you up to date, but if you have any hints where to continue
> digging, lemme know. Until it's fixed, I'll just work on
> wired-displays via ethernet instead of wifi-displays..
Based on what Oleksij said, these issues are likely not even related -
maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
call were to succeed it wouldn't work?
The issue here doesn't seem to be that call anyway, since that call was
for the data frames on the p2p-wlan1-0 interface, but rather seems to be
that ath9k_htc ignores the no-CCK parameter for the NL80211_CMD_FRAME
command (in mac80211, this would be IEEE80211_TX_CTL_NO_CCK_RATE)
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 15:15 ` [ath9k-devel] " Johannes Berg
@ 2013-12-16 15:26 ` Oleksij Rempel
-1 siblings, 0 replies; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-16 15:26 UTC (permalink / raw)
To: Johannes Berg, David Herrmann; +Cc: linux-wireless, ath9k-devel
Am 16.12.2013 16:15, schrieb Johannes Berg:
> On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
>
>> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
>
> Obviously :)
>
>> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
>> this working, and the devices are really nice apart from this bug. I
>> will keep you up to date, but if you have any hints where to continue
>> digging, lemme know. Until it's fixed, I'll just work on
>> wired-displays via ethernet instead of wifi-displays..
>
> Based on what Oleksij said, these issues are likely not even related -
> maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
> call were to succeed it wouldn't work?
Hmm.. WMI_BITRATE_MASK should do it.
ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
able to exclude CCK. Today i won't be able to check it.
> The issue here doesn't seem to be that call anyway, since that call was
> for the data frames on the p2p-wlan1-0 interface, but rather seems to be
> that ath9k_htc ignores the no-CCK parameter for the NL80211_CMD_FRAME
> command (in mac80211, this would be IEEE80211_TX_CTL_NO_CCK_RATE)
>
> johannes
>
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 15:26 ` Oleksij Rempel
0 siblings, 0 replies; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-16 15:26 UTC (permalink / raw)
To: ath9k-devel
Am 16.12.2013 16:15, schrieb Johannes Berg:
> On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
>
>> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
>
> Obviously :)
>
>> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
>> this working, and the devices are really nice apart from this bug. I
>> will keep you up to date, but if you have any hints where to continue
>> digging, lemme know. Until it's fixed, I'll just work on
>> wired-displays via ethernet instead of wifi-displays..
>
> Based on what Oleksij said, these issues are likely not even related -
> maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
> call were to succeed it wouldn't work?
Hmm.. WMI_BITRATE_MASK should do it.
ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
able to exclude CCK. Today i won't be able to check it.
> The issue here doesn't seem to be that call anyway, since that call was
> for the data frames on the p2p-wlan1-0 interface, but rather seems to be
> that ath9k_htc ignores the no-CCK parameter for the NL80211_CMD_FRAME
> command (in mac80211, this would be IEEE80211_TX_CTL_NO_CCK_RATE)
>
> johannes
>
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 15:26 ` [ath9k-devel] " Oleksij Rempel
@ 2013-12-16 15:29 ` Johannes Berg
-1 siblings, 0 replies; 24+ messages in thread
From: Johannes Berg @ 2013-12-16 15:29 UTC (permalink / raw)
To: Oleksij Rempel; +Cc: David Herrmann, linux-wireless, ath9k-devel
On Mon, 2013-12-16 at 16:26 +0100, Oleksij Rempel wrote:
> Am 16.12.2013 16:15, schrieb Johannes Berg:
> > On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
> >
> >> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
> >
> > Obviously :)
> >
> >> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
> >> this working, and the devices are really nice apart from this bug. I
> >> will keep you up to date, but if you have any hints where to continue
> >> digging, lemme know. Until it's fixed, I'll just work on
> >> wired-displays via ethernet instead of wifi-displays..
> >
> > Based on what Oleksij said, these issues are likely not even related -
> > maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
> > call were to succeed it wouldn't work?
>
> Hmm.. WMI_BITRATE_MASK should do it.
> ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
> able to exclude CCK. Today i won't be able to check it.
There are two things:
* the issue at hand, which is only for some certain management frames
that I
believe are sent over the normal wlan0 netdev/vif, but still must not
use CCK
even though wlan0 allows CCK
* the issue about the set tx-rate on the p2p netdev/vif, which is how I
noticed
this, but which is actually not related to the current bug
It sounds to me like only the latter can be solved with WMI_BITRATE_MASK
since you can't generally disable CCK on wlan0 when doing P2P (you might
be connected to an 11b AP at the same time)
For the latter issue, you really need a per-frame "disable CCK" flag in
the firmware, or you need to use a P2P_DEVICE vif.
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 15:29 ` Johannes Berg
0 siblings, 0 replies; 24+ messages in thread
From: Johannes Berg @ 2013-12-16 15:29 UTC (permalink / raw)
To: ath9k-devel
On Mon, 2013-12-16 at 16:26 +0100, Oleksij Rempel wrote:
> Am 16.12.2013 16:15, schrieb Johannes Berg:
> > On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
> >
> >> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
> >
> > Obviously :)
> >
> >> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
> >> this working, and the devices are really nice apart from this bug. I
> >> will keep you up to date, but if you have any hints where to continue
> >> digging, lemme know. Until it's fixed, I'll just work on
> >> wired-displays via ethernet instead of wifi-displays..
> >
> > Based on what Oleksij said, these issues are likely not even related -
> > maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
> > call were to succeed it wouldn't work?
>
> Hmm.. WMI_BITRATE_MASK should do it.
> ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
> able to exclude CCK. Today i won't be able to check it.
There are two things:
* the issue at hand, which is only for some certain management frames
that I
believe are sent over the normal wlan0 netdev/vif, but still must not
use CCK
even though wlan0 allows CCK
* the issue about the set tx-rate on the p2p netdev/vif, which is how I
noticed
this, but which is actually not related to the current bug
It sounds to me like only the latter can be solved with WMI_BITRATE_MASK
since you can't generally disable CCK on wlan0 when doing P2P (you might
be connected to an 11b AP at the same time)
For the latter issue, you really need a per-frame "disable CCK" flag in
the firmware, or you need to use a P2P_DEVICE vif.
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 15:29 ` [ath9k-devel] " Johannes Berg
@ 2013-12-16 15:37 ` Oleksij Rempel
-1 siblings, 0 replies; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-16 15:37 UTC (permalink / raw)
To: Johannes Berg; +Cc: David Herrmann, linux-wireless, ath9k-devel
Am 16.12.2013 16:29, schrieb Johannes Berg:
> On Mon, 2013-12-16 at 16:26 +0100, Oleksij Rempel wrote:
>> Am 16.12.2013 16:15, schrieb Johannes Berg:
>>> On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
>>>
>>>> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
>>>
>>> Obviously :)
>>>
>>>> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
>>>> this working, and the devices are really nice apart from this bug. I
>>>> will keep you up to date, but if you have any hints where to continue
>>>> digging, lemme know. Until it's fixed, I'll just work on
>>>> wired-displays via ethernet instead of wifi-displays..
>>>
>>> Based on what Oleksij said, these issues are likely not even related -
>>> maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
>>> call were to succeed it wouldn't work?
>>
>> Hmm.. WMI_BITRATE_MASK should do it.
>> ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
>> able to exclude CCK. Today i won't be able to check it.
>
> There are two things:
> * the issue at hand, which is only for some certain management frames
> that I
> believe are sent over the normal wlan0 netdev/vif, but still must not
> use CCK
> even though wlan0 allows CCK
> * the issue about the set tx-rate on the p2p netdev/vif, which is how I
> noticed
> this, but which is actually not related to the current bug
>
> It sounds to me like only the latter can be solved with WMI_BITRATE_MASK
> since you can't generally disable CCK on wlan0 when doing P2P (you might
> be connected to an 11b AP at the same time)
>
> For the latter issue, you really need a per-frame "disable CCK" flag in
> the firmware, or you need to use a P2P_DEVICE vif.
Ah.. there is comment which clarify the situation with
ieee80211_ops->set_bitrate_mask in ath9k_htc:
/*
* Currently, this is used only for selecting the minimum rate
* for management frames, rate selection for data frames remain
* unaffected.
*/
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 15:37 ` Oleksij Rempel
0 siblings, 0 replies; 24+ messages in thread
From: Oleksij Rempel @ 2013-12-16 15:37 UTC (permalink / raw)
To: ath9k-devel
Am 16.12.2013 16:29, schrieb Johannes Berg:
> On Mon, 2013-12-16 at 16:26 +0100, Oleksij Rempel wrote:
>> Am 16.12.2013 16:15, schrieb Johannes Berg:
>>> On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
>>>
>>>> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
>>>
>>> Obviously :)
>>>
>>>> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
>>>> this working, and the devices are really nice apart from this bug. I
>>>> will keep you up to date, but if you have any hints where to continue
>>>> digging, lemme know. Until it's fixed, I'll just work on
>>>> wired-displays via ethernet instead of wifi-displays..
>>>
>>> Based on what Oleksij said, these issues are likely not even related -
>>> maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
>>> call were to succeed it wouldn't work?
>>
>> Hmm.. WMI_BITRATE_MASK should do it.
>> ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
>> able to exclude CCK. Today i won't be able to check it.
>
> There are two things:
> * the issue at hand, which is only for some certain management frames
> that I
> believe are sent over the normal wlan0 netdev/vif, but still must not
> use CCK
> even though wlan0 allows CCK
> * the issue about the set tx-rate on the p2p netdev/vif, which is how I
> noticed
> this, but which is actually not related to the current bug
>
> It sounds to me like only the latter can be solved with WMI_BITRATE_MASK
> since you can't generally disable CCK on wlan0 when doing P2P (you might
> be connected to an 11b AP at the same time)
>
> For the latter issue, you really need a per-frame "disable CCK" flag in
> the firmware, or you need to use a P2P_DEVICE vif.
Ah.. there is comment which clarify the situation with
ieee80211_ops->set_bitrate_mask in ath9k_htc:
/*
* Currently, this is used only for selecting the minimum rate
* for management frames, rate selection for data frames remain
* unaffected.
*/
--
Regards,
Oleksij
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 15:37 ` [ath9k-devel] " Oleksij Rempel
@ 2013-12-16 15:53 ` David Herrmann
-1 siblings, 0 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-16 15:53 UTC (permalink / raw)
To: Oleksij Rempel; +Cc: Johannes Berg, linux-wireless, ath9k-devel
Hi
On Mon, Dec 16, 2013 at 4:37 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> Am 16.12.2013 16:29, schrieb Johannes Berg:
>> On Mon, 2013-12-16 at 16:26 +0100, Oleksij Rempel wrote:
>>> Am 16.12.2013 16:15, schrieb Johannes Berg:
>>>> On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
>>>>
>>>>> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
>>>>
>>>> Obviously :)
>>>>
>>>>> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
>>>>> this working, and the devices are really nice apart from this bug. I
>>>>> will keep you up to date, but if you have any hints where to continue
>>>>> digging, lemme know. Until it's fixed, I'll just work on
>>>>> wired-displays via ethernet instead of wifi-displays..
>>>>
>>>> Based on what Oleksij said, these issues are likely not even related -
>>>> maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
>>>> call were to succeed it wouldn't work?
>>>
>>> Hmm.. WMI_BITRATE_MASK should do it.
>>> ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
>>> able to exclude CCK. Today i won't be able to check it.
>>
>> There are two things:
>> * the issue at hand, which is only for some certain management frames
>> that I
>> believe are sent over the normal wlan0 netdev/vif, but still must not
>> use CCK
>> even though wlan0 allows CCK
>> * the issue about the set tx-rate on the p2p netdev/vif, which is how I
>> noticed
>> this, but which is actually not related to the current bug
>>
>> It sounds to me like only the latter can be solved with WMI_BITRATE_MASK
>> since you can't generally disable CCK on wlan0 when doing P2P (you might
>> be connected to an 11b AP at the same time)
>>
>> For the latter issue, you really need a per-frame "disable CCK" flag in
>> the firmware, or you need to use a P2P_DEVICE vif.
>
> Ah.. there is comment which clarify the situation with
> ieee80211_ops->set_bitrate_mask in ath9k_htc:
> /*
> * Currently, this is used only for selecting the minimum rate
> * for management frames, rate selection for data frames remain
> * unaffected.
> */
Yeah, I read that, but couldn't really understand it's meaning.. So it
seems unless we add fw-support to ignore CCK rates for p2p mgmt
frames, I'm screwed? Wouldn't it work to set >11mbits as lowest rate
which should exclude CCK, right? I'm fine with breaking other stuff if
I can get this running for a test environment. Or would it help trying
p2p on 5ghz? Not sure which rates are used there, though..
I will try to look into the ath9k-htc firmware. But given the
complexity, I guess I won't be able to do that in <1month. And my
80211 knowledge is not that comprehensive.. Maybe I'll find time for
it during my next semester.
Thanks!
David
^ permalink raw reply [flat|nested] 24+ messages in thread
* [ath9k-devel] [BUG] P2P setup timeout
@ 2013-12-16 15:53 ` David Herrmann
0 siblings, 0 replies; 24+ messages in thread
From: David Herrmann @ 2013-12-16 15:53 UTC (permalink / raw)
To: ath9k-devel
Hi
On Mon, Dec 16, 2013 at 4:37 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> Am 16.12.2013 16:29, schrieb Johannes Berg:
>> On Mon, 2013-12-16 at 16:26 +0100, Oleksij Rempel wrote:
>>> Am 16.12.2013 16:15, schrieb Johannes Berg:
>>>> On Mon, 2013-12-16 at 16:09 +0100, David Herrmann wrote:
>>>>
>>>>> Thanks, I tracked down the ENETDOWN. I'm not entirely sure but I think it's:
>>>>
>>>> Obviously :)
>>>>
>>>>> @Oleksij, I actually have three ath9k-htc devices so I'd like to get
>>>>> this working, and the devices are really nice apart from this bug. I
>>>>> will keep you up to date, but if you have any hints where to continue
>>>>> digging, lemme know. Until it's fixed, I'll just work on
>>>>> wired-displays via ethernet instead of wifi-displays..
>>>>
>>>> Based on what Oleksij said, these issues are likely not even related -
>>>> maybe ath9k_htc can't even set the rates to exclude CCK, so even if that
>>>> call were to succeed it wouldn't work?
>>>
>>> Hmm.. WMI_BITRATE_MASK should do it.
>>> ieee80211_ops->set_bitrate_mask is set, so theoretically we should be
>>> able to exclude CCK. Today i won't be able to check it.
>>
>> There are two things:
>> * the issue at hand, which is only for some certain management frames
>> that I
>> believe are sent over the normal wlan0 netdev/vif, but still must not
>> use CCK
>> even though wlan0 allows CCK
>> * the issue about the set tx-rate on the p2p netdev/vif, which is how I
>> noticed
>> this, but which is actually not related to the current bug
>>
>> It sounds to me like only the latter can be solved with WMI_BITRATE_MASK
>> since you can't generally disable CCK on wlan0 when doing P2P (you might
>> be connected to an 11b AP at the same time)
>>
>> For the latter issue, you really need a per-frame "disable CCK" flag in
>> the firmware, or you need to use a P2P_DEVICE vif.
>
> Ah.. there is comment which clarify the situation with
> ieee80211_ops->set_bitrate_mask in ath9k_htc:
> /*
> * Currently, this is used only for selecting the minimum rate
> * for management frames, rate selection for data frames remain
> * unaffected.
> */
Yeah, I read that, but couldn't really understand it's meaning.. So it
seems unless we add fw-support to ignore CCK rates for p2p mgmt
frames, I'm screwed? Wouldn't it work to set >11mbits as lowest rate
which should exclude CCK, right? I'm fine with breaking other stuff if
I can get this running for a test environment. Or would it help trying
p2p on 5ghz? Not sure which rates are used there, though..
I will try to look into the ath9k-htc firmware. But given the
complexity, I guess I won't be able to do that in <1month. And my
80211 knowledge is not that comprehensive.. Maybe I'll find time for
it during my next semester.
Thanks!
David
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-16 13:45 ` Johannes Berg
2013-12-16 13:51 ` David Herrmann
@ 2013-12-17 5:50 ` Ujjal Roy
2013-12-17 7:19 ` Johannes Berg
1 sibling, 1 reply; 24+ messages in thread
From: Ujjal Roy @ 2013-12-17 5:50 UTC (permalink / raw)
To: Johannes Berg, David Herrmann; +Cc: linux-wireless
Hi Johannes,
On 12/16/2013 07:15 PM, Johannes Berg wrote:
> On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
>
> Right, and I suspect they don't get a response because (as the sniffer
> trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
> in the P2P spec (must use OFDM).
>
Can you please let me know, is the P2P spec freely available to read or
download? If so, please provide some info from where I can able to get
the document. Actually, I need to know - how to add P2P_DEVICE support
in a driver.
Thanks,
UjjaL
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [BUG] P2P setup timeout
2013-12-17 5:50 ` Ujjal Roy
@ 2013-12-17 7:19 ` Johannes Berg
0 siblings, 0 replies; 24+ messages in thread
From: Johannes Berg @ 2013-12-17 7:19 UTC (permalink / raw)
To: Ujjal Roy; +Cc: David Herrmann, linux-wireless
On Tue, 2013-12-17 at 11:20 +0530, Ujjal Roy wrote:
> Hi Johannes,
>
> On 12/16/2013 07:15 PM, Johannes Berg wrote:
> > On Mon, 2013-12-16 at 14:39 +0100, David Herrmann wrote:
> >
> > Right, and I suspect they don't get a response because (as the sniffer
> > trace tells me) they're sent with 1 Mbps (a CCK rate), which is invalid
> > in the P2P spec (must use OFDM).
> >
>
> Can you please let me know, is the P2P spec freely available to read or
> download? If so, please provide some info from where I can able to get
> the document. Actually, I need to know - how to add P2P_DEVICE support
> in a driver.
No, it isn't. However, P2P_DEVICE support is not described in the spec
anyway since it's a Linux thing.
johannes
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2013-12-17 7:20 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-12-06 10:18 [BUG] P2P setup timeout David Herrmann
2013-12-09 14:03 ` Oleksij Rempel
2013-12-09 14:30 ` David Herrmann
2013-12-16 12:00 ` David Herrmann
2013-12-16 12:36 ` Johannes Berg
2013-12-16 13:39 ` David Herrmann
2013-12-16 13:45 ` Johannes Berg
2013-12-16 13:51 ` David Herrmann
2013-12-16 14:57 ` Oleksij Rempel
2013-12-16 14:57 ` [ath9k-devel] " Oleksij Rempel
2013-12-16 15:09 ` David Herrmann
2013-12-16 15:09 ` [ath9k-devel] " David Herrmann
2013-12-16 15:15 ` Johannes Berg
2013-12-16 15:15 ` [ath9k-devel] " Johannes Berg
2013-12-16 15:26 ` Oleksij Rempel
2013-12-16 15:26 ` [ath9k-devel] " Oleksij Rempel
2013-12-16 15:29 ` Johannes Berg
2013-12-16 15:29 ` [ath9k-devel] " Johannes Berg
2013-12-16 15:37 ` Oleksij Rempel
2013-12-16 15:37 ` [ath9k-devel] " Oleksij Rempel
2013-12-16 15:53 ` David Herrmann
2013-12-16 15:53 ` [ath9k-devel] " David Herrmann
2013-12-17 5:50 ` Ujjal Roy
2013-12-17 7:19 ` Johannes Berg
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.