* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
@ 2013-12-18 22:23 Chin Liang See
2014-01-09 14:47 ` Chin Liang See
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Chin Liang See @ 2013-12-18 22:23 UTC (permalink / raw)
To: u-boot
To add the DesignWare watchdog driver support. It required
information such as register base address and clock info from
configuration header file within include/configs folder.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
---
drivers/watchdog/Makefile | 1 +
drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
2 files changed, 76 insertions(+)
create mode 100644 drivers/watchdog/designware_wdt.c
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 06ced10..0276a10 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -15,3 +15,4 @@ obj-$(CONFIG_S5P) += s5p_wdt.o
obj-$(CONFIG_XILINX_TB_WATCHDOG) += xilinx_tb_wdt.o
obj-$(CONFIG_BFIN_WATCHDOG) += bfin_wdt.o
obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.o
+obj-$(CONFIG_DESIGNWARE_WATCHDOG) += designware_wdt.o
diff --git a/drivers/watchdog/designware_wdt.c b/drivers/watchdog/designware_wdt.c
new file mode 100644
index 0000000..c3b14f5
--- /dev/null
+++ b/drivers/watchdog/designware_wdt.c
@@ -0,0 +1,75 @@
+/*
+ * Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <asm/io.h>
+#include <asm/utils.h>
+
+#define DW_WDT_CR 0x00
+#define DW_WDT_TORR 0x04
+#define DW_WDT_CRR 0x0C
+
+#define DW_WDT_CR_EN_OFFSET 0x00
+#define DW_WDT_CR_RMOD_OFFSET 0x01
+#define DW_WDT_CR_RMOD_VAL 0x00
+#define DW_WDT_CRR_RESTART_VAL 0x76
+
+/*
+ * Set the watchdog time interval.
+ * Counter is 32 bit.
+ */
+int designware_wdt_settimeout(unsigned int timeout)
+{
+ signed int i;
+ /* calculate the timeout range value */
+ i = (log_2_n_round_up(timeout * CONFIG_DW_WDT_CLOCK_KHZ))\
+ - 16;
+ if (i > 15)
+ i = 15;
+ if (i < 0)
+ i = 0;
+
+ writel((i | (i<<4)),
+ (CONFIG_DW_WDT_BASE + DW_WDT_TORR));
+ return 0;
+}
+
+void designware_wdt_enable(void)
+{
+ writel(((DW_WDT_CR_RMOD_VAL << DW_WDT_CR_RMOD_OFFSET) | \
+ (0x1 << DW_WDT_CR_EN_OFFSET)),
+ (CONFIG_DW_WDT_BASE + DW_WDT_CR));
+}
+
+unsigned int designware_wdt_is_enabled(void)
+{
+ unsigned long val;
+ val = readl((CONFIG_DW_WDT_BASE + DW_WDT_CR));
+ return val & 0x1;
+}
+
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+ if (designware_wdt_is_enabled())
+ /* restart the watchdog counter */
+ writel(DW_WDT_CRR_RESTART_VAL,
+ (CONFIG_DW_WDT_BASE + DW_WDT_CRR));
+}
+
+void hw_watchdog_init(void)
+{
+ /* reset to disable the watchdog */
+ hw_watchdog_reset();
+ /* set timer in miliseconds */
+ designware_wdt_settimeout(CONFIG_HW_WATCHDOG_TIMEOUT_MS);
+ /* enable the watchdog */
+ designware_wdt_enable();
+ /* reset the watchdog */
+ hw_watchdog_reset();
+}
+#endif
--
1.7.9.5
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
2013-12-18 22:23 [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support Chin Liang See
@ 2014-01-09 14:47 ` Chin Liang See
2014-02-04 19:08 ` Chin Liang See
2014-02-13 9:35 ` Albert ARIBAUD
2 siblings, 0 replies; 7+ messages in thread
From: Chin Liang See @ 2014-01-09 14:47 UTC (permalink / raw)
To: u-boot
Hi guys,
Wonder any comments for this patch?
Thanks
Chin Liang
On Wed, 2013-12-18 at 16:23 -0600, Chin Liang See wrote:
> To add the DesignWare watchdog driver support. It required
> information such as register base address and clock info from
> configuration header file within include/configs folder.
>
> Signed-off-by: Chin Liang See <clsee@altera.com>
> Cc: Anatolij Gustschin <agust@denx.de>
> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
> Cc: Heiko Schocher <hs@denx.de>
> Cc: Tom Rini <trini@ti.com>
> ---
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
> 2 files changed, 76 insertions(+)
> create mode 100644 drivers/watchdog/designware_wdt.c
>
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 06ced10..0276a10 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -15,3 +15,4 @@ obj-$(CONFIG_S5P) += s5p_wdt.o
> obj-$(CONFIG_XILINX_TB_WATCHDOG) += xilinx_tb_wdt.o
> obj-$(CONFIG_BFIN_WATCHDOG) += bfin_wdt.o
> obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.o
> +obj-$(CONFIG_DESIGNWARE_WATCHDOG) += designware_wdt.o
> diff --git a/drivers/watchdog/designware_wdt.c b/drivers/watchdog/designware_wdt.c
> new file mode 100644
> index 0000000..c3b14f5
> --- /dev/null
> +++ b/drivers/watchdog/designware_wdt.c
> @@ -0,0 +1,75 @@
> +/*
> + * Copyright (C) 2013 Altera Corporation <www.altera.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <watchdog.h>
> +#include <asm/io.h>
> +#include <asm/utils.h>
> +
> +#define DW_WDT_CR 0x00
> +#define DW_WDT_TORR 0x04
> +#define DW_WDT_CRR 0x0C
> +
> +#define DW_WDT_CR_EN_OFFSET 0x00
> +#define DW_WDT_CR_RMOD_OFFSET 0x01
> +#define DW_WDT_CR_RMOD_VAL 0x00
> +#define DW_WDT_CRR_RESTART_VAL 0x76
> +
> +/*
> + * Set the watchdog time interval.
> + * Counter is 32 bit.
> + */
> +int designware_wdt_settimeout(unsigned int timeout)
> +{
> + signed int i;
> + /* calculate the timeout range value */
> + i = (log_2_n_round_up(timeout * CONFIG_DW_WDT_CLOCK_KHZ))\
> + - 16;
> + if (i > 15)
> + i = 15;
> + if (i < 0)
> + i = 0;
> +
> + writel((i | (i<<4)),
> + (CONFIG_DW_WDT_BASE + DW_WDT_TORR));
> + return 0;
> +}
> +
> +void designware_wdt_enable(void)
> +{
> + writel(((DW_WDT_CR_RMOD_VAL << DW_WDT_CR_RMOD_OFFSET) | \
> + (0x1 << DW_WDT_CR_EN_OFFSET)),
> + (CONFIG_DW_WDT_BASE + DW_WDT_CR));
> +}
> +
> +unsigned int designware_wdt_is_enabled(void)
> +{
> + unsigned long val;
> + val = readl((CONFIG_DW_WDT_BASE + DW_WDT_CR));
> + return val & 0x1;
> +}
> +
> +#if defined(CONFIG_HW_WATCHDOG)
> +void hw_watchdog_reset(void)
> +{
> + if (designware_wdt_is_enabled())
> + /* restart the watchdog counter */
> + writel(DW_WDT_CRR_RESTART_VAL,
> + (CONFIG_DW_WDT_BASE + DW_WDT_CRR));
> +}
> +
> +void hw_watchdog_init(void)
> +{
> + /* reset to disable the watchdog */
> + hw_watchdog_reset();
> + /* set timer in miliseconds */
> + designware_wdt_settimeout(CONFIG_HW_WATCHDOG_TIMEOUT_MS);
> + /* enable the watchdog */
> + designware_wdt_enable();
> + /* reset the watchdog */
> + hw_watchdog_reset();
> +}
> +#endif
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
2013-12-18 22:23 [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support Chin Liang See
2014-01-09 14:47 ` Chin Liang See
@ 2014-02-04 19:08 ` Chin Liang See
2014-02-13 9:35 ` Albert ARIBAUD
2 siblings, 0 replies; 7+ messages in thread
From: Chin Liang See @ 2014-02-04 19:08 UTC (permalink / raw)
To: u-boot
Hi Albert,
As there are no further comments, would need your help to apply this
patch. Thanks and appreciate for your support.
Chin Liang
On Wed, 2013-12-18 at 16:23 -0600, Chin Liang See wrote:
> To add the DesignWare watchdog driver support. It required
> information such as register base address and clock info from
> configuration header file within include/configs folder.
>
> Signed-off-by: Chin Liang See <clsee@altera.com>
> Cc: Anatolij Gustschin <agust@denx.de>
> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
> Cc: Heiko Schocher <hs@denx.de>
> Cc: Tom Rini <trini@ti.com>
> ---
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
> 2 files changed, 76 insertions(+)
> create mode 100644 drivers/watchdog/designware_wdt.c
>
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 06ced10..0276a10 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -15,3 +15,4 @@ obj-$(CONFIG_S5P) += s5p_wdt.o
> obj-$(CONFIG_XILINX_TB_WATCHDOG) += xilinx_tb_wdt.o
> obj-$(CONFIG_BFIN_WATCHDOG) += bfin_wdt.o
> obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.o
> +obj-$(CONFIG_DESIGNWARE_WATCHDOG) += designware_wdt.o
> diff --git a/drivers/watchdog/designware_wdt.c b/drivers/watchdog/designware_wdt.c
> new file mode 100644
> index 0000000..c3b14f5
> --- /dev/null
> +++ b/drivers/watchdog/designware_wdt.c
> @@ -0,0 +1,75 @@
> +/*
> + * Copyright (C) 2013 Altera Corporation <www.altera.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <watchdog.h>
> +#include <asm/io.h>
> +#include <asm/utils.h>
> +
> +#define DW_WDT_CR 0x00
> +#define DW_WDT_TORR 0x04
> +#define DW_WDT_CRR 0x0C
> +
> +#define DW_WDT_CR_EN_OFFSET 0x00
> +#define DW_WDT_CR_RMOD_OFFSET 0x01
> +#define DW_WDT_CR_RMOD_VAL 0x00
> +#define DW_WDT_CRR_RESTART_VAL 0x76
> +
> +/*
> + * Set the watchdog time interval.
> + * Counter is 32 bit.
> + */
> +int designware_wdt_settimeout(unsigned int timeout)
> +{
> + signed int i;
> + /* calculate the timeout range value */
> + i = (log_2_n_round_up(timeout * CONFIG_DW_WDT_CLOCK_KHZ))\
> + - 16;
> + if (i > 15)
> + i = 15;
> + if (i < 0)
> + i = 0;
> +
> + writel((i | (i<<4)),
> + (CONFIG_DW_WDT_BASE + DW_WDT_TORR));
> + return 0;
> +}
> +
> +void designware_wdt_enable(void)
> +{
> + writel(((DW_WDT_CR_RMOD_VAL << DW_WDT_CR_RMOD_OFFSET) | \
> + (0x1 << DW_WDT_CR_EN_OFFSET)),
> + (CONFIG_DW_WDT_BASE + DW_WDT_CR));
> +}
> +
> +unsigned int designware_wdt_is_enabled(void)
> +{
> + unsigned long val;
> + val = readl((CONFIG_DW_WDT_BASE + DW_WDT_CR));
> + return val & 0x1;
> +}
> +
> +#if defined(CONFIG_HW_WATCHDOG)
> +void hw_watchdog_reset(void)
> +{
> + if (designware_wdt_is_enabled())
> + /* restart the watchdog counter */
> + writel(DW_WDT_CRR_RESTART_VAL,
> + (CONFIG_DW_WDT_BASE + DW_WDT_CRR));
> +}
> +
> +void hw_watchdog_init(void)
> +{
> + /* reset to disable the watchdog */
> + hw_watchdog_reset();
> + /* set timer in miliseconds */
> + designware_wdt_settimeout(CONFIG_HW_WATCHDOG_TIMEOUT_MS);
> + /* enable the watchdog */
> + designware_wdt_enable();
> + /* reset the watchdog */
> + hw_watchdog_reset();
> +}
> +#endif
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
2013-12-18 22:23 [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support Chin Liang See
2014-01-09 14:47 ` Chin Liang See
2014-02-04 19:08 ` Chin Liang See
@ 2014-02-13 9:35 ` Albert ARIBAUD
2014-02-21 16:00 ` Chin Liang See
2 siblings, 1 reply; 7+ messages in thread
From: Albert ARIBAUD @ 2014-02-13 9:35 UTC (permalink / raw)
To: u-boot
Hi Chin,
On Wed, 18 Dec 2013 16:23:35 -0600, Chin Liang See <clsee@altera.com>
wrote:
> To add the DesignWare watchdog driver support. It required
> information such as register base address and clock info from
> configuration header file within include/configs folder.
>
> Signed-off-by: Chin Liang See <clsee@altera.com>
> Cc: Anatolij Gustschin <agust@denx.de>
> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
> Cc: Heiko Schocher <hs@denx.de>
> Cc: Tom Rini <trini@ti.com>
> ---
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
> 2 files changed, 76 insertions(+)
> create mode 100644 drivers/watchdog/designware_wdt.c
As such, this code is dead code in that no board uses this watchdog --
same as the NAND driver series assigned to scott Wood (cc:).
If there is a board which uses these drivers, please resubmit the
drivers and board patches in a single series where some board config
is made to use them.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
2014-02-13 9:35 ` Albert ARIBAUD
@ 2014-02-21 16:00 ` Chin Liang See
2014-02-21 16:58 ` Albert ARIBAUD
0 siblings, 1 reply; 7+ messages in thread
From: Chin Liang See @ 2014-02-21 16:00 UTC (permalink / raw)
To: u-boot
Hi Albert,
On Thu, 2014-02-13 at 10:35 +0100, ZY - albert.u.boot wrote:
> Hi Chin,
>
> On Wed, 18 Dec 2013 16:23:35 -0600, Chin Liang See <clsee@altera.com>
> wrote:
>
> > To add the DesignWare watchdog driver support. It required
> > information such as register base address and clock info from
> > configuration header file within include/configs folder.
> >
> > Signed-off-by: Chin Liang See <clsee@altera.com>
> > Cc: Anatolij Gustschin <agust@denx.de>
> > Cc: Albert Aribaud <albert.u.boot@aribaud.net>
> > Cc: Heiko Schocher <hs@denx.de>
> > Cc: Tom Rini <trini@ti.com>
> > ---
> > drivers/watchdog/Makefile | 1 +
> > drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
> > 2 files changed, 76 insertions(+)
> > create mode 100644 drivers/watchdog/designware_wdt.c
>
> As such, this code is dead code in that no board uses this watchdog --
> same as the NAND driver series assigned to scott Wood (cc:).
>
> If there is a board which uses these drivers, please resubmit the
> drivers and board patches in a single series where some board config
> is made to use them.
>
> Amicalement,
Sorry my bad as I would thought they would need 2 different patches. Let
me fix this watchdog and nand patch. Thanks
Chin Liang
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
2014-02-21 16:00 ` Chin Liang See
@ 2014-02-21 16:58 ` Albert ARIBAUD
2014-02-21 20:50 ` Chin Liang See
0 siblings, 1 reply; 7+ messages in thread
From: Albert ARIBAUD @ 2014-02-21 16:58 UTC (permalink / raw)
To: u-boot
Hi Chin,
On Fri, 21 Feb 2014 10:00:08 -0600, Chin Liang See <clsee@altera.com>
wrote:
> Hi Albert,
>
> On Thu, 2014-02-13 at 10:35 +0100, ZY - albert.u.boot wrote:
> > Hi Chin,
> >
> > On Wed, 18 Dec 2013 16:23:35 -0600, Chin Liang See <clsee@altera.com>
> > wrote:
> >
> > > To add the DesignWare watchdog driver support. It required
> > > information such as register base address and clock info from
> > > configuration header file within include/configs folder.
> > >
> > > Signed-off-by: Chin Liang See <clsee@altera.com>
> > > Cc: Anatolij Gustschin <agust@denx.de>
> > > Cc: Albert Aribaud <albert.u.boot@aribaud.net>
> > > Cc: Heiko Schocher <hs@denx.de>
> > > Cc: Tom Rini <trini@ti.com>
> > > ---
> > > drivers/watchdog/Makefile | 1 +
> > > drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
> > > 2 files changed, 76 insertions(+)
> > > create mode 100644 drivers/watchdog/designware_wdt.c
> >
> > As such, this code is dead code in that no board uses this watchdog --
> > same as the NAND driver series assigned to scott Wood (cc:).
> >
> > If there is a board which uses these drivers, please resubmit the
> > drivers and board patches in a single series where some board config
> > is made to use them.
> >
> > Amicalement,
>
> Sorry my bad as I would thought they would need 2 different patches.
Actually it could have been two different patches, but in a single
series (i.e., patch 1/2 provides the driver, patch 2/2 provides the
configurations which use the driver).
> Chin Liang
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support
2014-02-21 16:58 ` Albert ARIBAUD
@ 2014-02-21 20:50 ` Chin Liang See
0 siblings, 0 replies; 7+ messages in thread
From: Chin Liang See @ 2014-02-21 20:50 UTC (permalink / raw)
To: u-boot
Hi Albert,
On Fri, 2014-02-21 at 17:58 +0100, ZY - albert.u.boot wrote:
> Hi Chin,
>
> On Fri, 21 Feb 2014 10:00:08 -0600, Chin Liang See <clsee@altera.com>
> wrote:
>
> > Hi Albert,
> >
> > On Thu, 2014-02-13 at 10:35 +0100, ZY - albert.u.boot wrote:
> > > Hi Chin,
> > >
> > > On Wed, 18 Dec 2013 16:23:35 -0600, Chin Liang See <clsee@altera.com>
> > > wrote:
> > >
> > > > To add the DesignWare watchdog driver support. It required
> > > > information such as register base address and clock info from
> > > > configuration header file within include/configs folder.
> > > >
> > > > Signed-off-by: Chin Liang See <clsee@altera.com>
> > > > Cc: Anatolij Gustschin <agust@denx.de>
> > > > Cc: Albert Aribaud <albert.u.boot@aribaud.net>
> > > > Cc: Heiko Schocher <hs@denx.de>
> > > > Cc: Tom Rini <trini@ti.com>
> > > > ---
> > > > drivers/watchdog/Makefile | 1 +
> > > > drivers/watchdog/designware_wdt.c | 75 +++++++++++++++++++++++++++++++++++++
> > > > 2 files changed, 76 insertions(+)
> > > > create mode 100644 drivers/watchdog/designware_wdt.c
> > >
> > > As such, this code is dead code in that no board uses this watchdog --
> > > same as the NAND driver series assigned to scott Wood (cc:).
> > >
> > > If there is a board which uses these drivers, please resubmit the
> > > drivers and board patches in a single series where some board config
> > > is made to use them.
> > >
> > > Amicalement,
> >
> > Sorry my bad as I would thought they would need 2 different patches.
>
> Actually it could have been two different patches, but in a single
> series (i.e., patch 1/2 provides the driver, patch 2/2 provides the
> configurations which use the driver).
>
Sure I can do that too. Thanks!
Chin Liang
> > Chin Liang
>
> Amicalement,
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2014-02-21 20:50 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-12-18 22:23 [U-Boot] [PATCH] watchdog/denali: Adding DesignWare watchdog driver support Chin Liang See
2014-01-09 14:47 ` Chin Liang See
2014-02-04 19:08 ` Chin Liang See
2014-02-13 9:35 ` Albert ARIBAUD
2014-02-21 16:00 ` Chin Liang See
2014-02-21 16:58 ` Albert ARIBAUD
2014-02-21 20:50 ` Chin Liang See
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.