[PATCH v3 0/4] ata: ahci_platform related cleanups

[PATCH v3 0/4] ata: ahci_platform related cleanups

[Bartlomiej Zolnierkiewicz]

Hi,

This patch series:
- fixes ahci_platform_data->suspend() handling
- moves library AHCI platform code to its own file
- adds a new-style AHCI platform driver for DaVinci DA850 AHCI controller
- updates DaVinci DA850 platform code

Changes since v2:
- merged changes from Sekhar
- splitted out DaVinci DA850 platform changes into separate patch

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics


Bartlomiej Zolnierkiewicz (4):
  ata: ahci_platform: fix ahci_platform_data->suspend method handling
  ata: move library code from ahci_platform.c to libahci_platform.c
  ata: add new-style AHCI platform driver for DaVinci DA850 AHCI
    controller
  ARM: davinci: da850: update SATA AHCI support

 arch/arm/mach-davinci/da850.c         |   2 +-
 arch/arm/mach-davinci/devices-da8xx.c |  99 +------
 drivers/ata/Kconfig                   |  14 +-
 drivers/ata/Makefile                  |   9 +-
 drivers/ata/ahci_da850.c              | 114 +++++++
 drivers/ata/ahci_platform.c           | 508 -------------------------------
 drivers/ata/libahci_platform.c        | 541 ++++++++++++++++++++++++++++++++++
 7 files changed, 680 insertions(+), 607 deletions(-)
 create mode 100644 drivers/ata/ahci_da850.c
 create mode 100644 drivers/ata/libahci_platform.c

-- 
1.8.2.3

[PATCH v3 0/4] ata: ahci_platform related cleanups

[Bartlomiej Zolnierkiewicz]

Hi,

This patch series:
- fixes ahci_platform_data->suspend() handling
- moves library AHCI platform code to its own file
- adds a new-style AHCI platform driver for DaVinci DA850 AHCI controller
- updates DaVinci DA850 platform code

Changes since v2:
- merged changes from Sekhar
- splitted out DaVinci DA850 platform changes into separate patch

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics


Bartlomiej Zolnierkiewicz (4):
  ata: ahci_platform: fix ahci_platform_data->suspend method handling
  ata: move library code from ahci_platform.c to libahci_platform.c
  ata: add new-style AHCI platform driver for DaVinci DA850 AHCI
    controller
  ARM: davinci: da850: update SATA AHCI support

 arch/arm/mach-davinci/da850.c         |   2 +-
 arch/arm/mach-davinci/devices-da8xx.c |  99 +------
 drivers/ata/Kconfig                   |  14 +-
 drivers/ata/Makefile                  |   9 +-
 drivers/ata/ahci_da850.c              | 114 +++++++
 drivers/ata/ahci_platform.c           | 508 -------------------------------
 drivers/ata/libahci_platform.c        | 541 ++++++++++++++++++++++++++++++++++
 7 files changed, 680 insertions(+), 607 deletions(-)
 create mode 100644 drivers/ata/ahci_da850.c
 create mode 100644 drivers/ata/libahci_platform.c

-- 
1.8.2.3

[PATCH v3 0/4] ata: ahci_platform related cleanups

[Bartlomiej Zolnierkiewicz]

Hi,

This patch series:
- fixes ahci_platform_data->suspend() handling
- moves library AHCI platform code to its own file
- adds a new-style AHCI platform driver for DaVinci DA850 AHCI controller
- updates DaVinci DA850 platform code

Changes since v2:
- merged changes from Sekhar
- splitted out DaVinci DA850 platform changes into separate patch

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics


Bartlomiej Zolnierkiewicz (4):
  ata: ahci_platform: fix ahci_platform_data->suspend method handling
  ata: move library code from ahci_platform.c to libahci_platform.c
  ata: add new-style AHCI platform driver for DaVinci DA850 AHCI
    controller
  ARM: davinci: da850: update SATA AHCI support

 arch/arm/mach-davinci/da850.c         |   2 +-
 arch/arm/mach-davinci/devices-da8xx.c |  99 +------
 drivers/ata/Kconfig                   |  14 +-
 drivers/ata/Makefile                  |   9 +-
 drivers/ata/ahci_da850.c              | 114 +++++++
 drivers/ata/ahci_platform.c           | 508 -------------------------------
 drivers/ata/libahci_platform.c        | 541 ++++++++++++++++++++++++++++++++++
 7 files changed, 680 insertions(+), 607 deletions(-)
 create mode 100644 drivers/ata/ahci_da850.c
 create mode 100644 drivers/ata/libahci_platform.c

-- 
1.8.2.3

[PATCH v3 1/4] ata: ahci_platform: fix ahci_platform_data->suspend method handling

[Bartlomiej Zolnierkiewicz]

Looking at ST SPEAr1340 AHCI code (the only user of the deprecated
pdata->suspend and pdata->resume) it is obvious the we should return
after calling pdata->suspend() only if the function have returned
non-zero return value.  The code has been broken since commit 1e70c2
("ata/ahci_platform: Add clock framework support").  Fix it.

Cc: Viresh Kumar <viresh.linux-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: Shiraz Hashim <shiraz.hashim-qxv4g6HH51o@public.gmane.org>
Acked-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
v3:
- no changes
v2:
- updated patch description

 drivers/ata/ahci_platform.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 70fbf66..7bd6adf 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -521,12 +521,19 @@ int ahci_platform_suspend(struct device *dev)
 	if (rc)
 		return rc;
 
-	if (pdata && pdata->suspend)
-		return pdata->suspend(dev);
+	if (pdata && pdata->suspend) {
+		rc = pdata->suspend(dev);
+		if (rc)
+			goto resume_host;
+	}
 
 	ahci_platform_disable_resources(hpriv);
 
 	return 0;
+
+resume_host:
+	ahci_platform_resume_host(dev);
+	return rc;
 }
 EXPORT_SYMBOL_GPL(ahci_platform_suspend);
 
-- 
1.8.2.3

[PATCH v3 1/4] ata: ahci_platform: fix ahci_platform_data->suspend method handling

[Bartlomiej Zolnierkiewicz]

Looking at ST SPEAr1340 AHCI code (the only user of the deprecated
pdata->suspend and pdata->resume) it is obvious the we should return
after calling pdata->suspend() only if the function have returned
non-zero return value.  The code has been broken since commit 1e70c2
("ata/ahci_platform: Add clock framework support").  Fix it.

Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- no changes
v2:
- updated patch description

 drivers/ata/ahci_platform.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 70fbf66..7bd6adf 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -521,12 +521,19 @@ int ahci_platform_suspend(struct device *dev)
 	if (rc)
 		return rc;
 
-	if (pdata && pdata->suspend)
-		return pdata->suspend(dev);
+	if (pdata && pdata->suspend) {
+		rc = pdata->suspend(dev);
+		if (rc)
+			goto resume_host;
+	}
 
 	ahci_platform_disable_resources(hpriv);
 
 	return 0;
+
+resume_host:
+	ahci_platform_resume_host(dev);
+	return rc;
 }
 EXPORT_SYMBOL_GPL(ahci_platform_suspend);
 
-- 
1.8.2.3

[PATCH v3 1/4] ata: ahci_platform: fix ahci_platform_data->suspend method handling

[Bartlomiej Zolnierkiewicz]

Looking at ST SPEAr1340 AHCI code (the only user of the deprecated
pdata->suspend and pdata->resume) it is obvious the we should return
after calling pdata->suspend() only if the function have returned
non-zero return value.  The code has been broken since commit 1e70c2
("ata/ahci_platform: Add clock framework support").  Fix it.

Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- no changes
v2:
- updated patch description

 drivers/ata/ahci_platform.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 70fbf66..7bd6adf 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -521,12 +521,19 @@ int ahci_platform_suspend(struct device *dev)
 	if (rc)
 		return rc;
 
-	if (pdata && pdata->suspend)
-		return pdata->suspend(dev);
+	if (pdata && pdata->suspend) {
+		rc = pdata->suspend(dev);
+		if (rc)
+			goto resume_host;
+	}
 
 	ahci_platform_disable_resources(hpriv);
 
 	return 0;
+
+resume_host:
+	ahci_platform_resume_host(dev);
+	return rc;
 }
 EXPORT_SYMBOL_GPL(ahci_platform_suspend);
 
-- 
1.8.2.3

[PATCH v3 2/4] ata: move library code from ahci_platform.c to libahci_platform.c

[Bartlomiej Zolnierkiewicz]

Move AHCI platform library code from ahci_platform.c to
libahci_platform.c and fix dependencies for ahci_st,
ahci_imx and ahci_sunxi drivers.

Acked-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
v3:
- no changes
v2:
- updated patch description

 drivers/ata/Kconfig            |   5 +-
 drivers/ata/Makefile           |   8 +-
 drivers/ata/ahci_platform.c    | 515 ---------------------------------------
 drivers/ata/libahci_platform.c | 541 +++++++++++++++++++++++++++++++++++++++++
 4 files changed, 547 insertions(+), 522 deletions(-)
 create mode 100644 drivers/ata/libahci_platform.c

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index c4db48c..371e8890 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -99,7 +99,6 @@ config SATA_AHCI_PLATFORM
 
 config AHCI_ST
 	tristate "ST AHCI SATA support"
-	depends on SATA_AHCI_PLATFORM
 	depends on ARCH_STI
 	help
 	  This option enables support for ST AHCI SATA controller.
@@ -108,7 +107,7 @@ config AHCI_ST
 
 config AHCI_IMX
 	tristate "Freescale i.MX AHCI SATA support"
-	depends on SATA_AHCI_PLATFORM && MFD_SYSCON
+	depends on MFD_SYSCON
 	help
 	  This option enables support for the Freescale i.MX SoC's
 	  onboard AHCI SATA.
@@ -117,7 +116,7 @@ config AHCI_IMX
 
 config AHCI_SUNXI
 	tristate "Allwinner sunxi AHCI SATA support"
-	depends on ARCH_SUNXI && SATA_AHCI_PLATFORM
+	depends on ARCH_SUNXI
 	help
 	  This option enables support for the Allwinner sunxi SoC's
 	  onboard AHCI SATA.
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index e20148c..6123e64 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -4,15 +4,15 @@ obj-$(CONFIG_ATA)		+= libata.o
 # non-SFF interface
 obj-$(CONFIG_SATA_AHCI)		+= ahci.o libahci.o
 obj-$(CONFIG_SATA_ACARD_AHCI)	+= acard-ahci.o libahci.o
-obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o
+obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o libahci_platform.o
 obj-$(CONFIG_SATA_FSL)		+= sata_fsl.o
 obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
-obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o
-obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o
-obj-$(CONFIG_AHCI_ST)		+= ahci_st.o
+obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
 
 # SFF w/ custom DMA
 obj-$(CONFIG_PDC_ADMA)		+= pdc_adma.o
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 7bd6adf..ef67e79 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -12,28 +12,15 @@
  * any later version.
  */
 
-#include <linux/clk.h>
 #include <linux/kernel.h>
-#include <linux/gfp.h>
 #include <linux/module.h>
 #include <linux/pm.h>
-#include <linux/interrupt.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/libata.h>
 #include <linux/ahci_platform.h>
-#include <linux/phy/phy.h>
-#include <linux/pm_runtime.h>
 #include "ahci.h"
 
-static void ahci_host_stop(struct ata_host *host);
-
-struct ata_port_operations ahci_platform_ops = {
-	.inherits	= &ahci_ops,
-	.host_stop	= ahci_host_stop,
-};
-EXPORT_SYMBOL_GPL(ahci_platform_ops);
-
 static const struct ata_port_info ahci_port_info = {
 	.flags		= AHCI_FLAG_COMMON,
 	.pio_mask	= ATA_PIO4,
@@ -41,345 +28,6 @@ static const struct ata_port_info ahci_port_info = {
 	.port_ops	= &ahci_platform_ops,
 };
 
-static struct scsi_host_template ahci_platform_sht = {
-	AHCI_SHT("ahci_platform"),
-};
-
-/**
- * ahci_platform_enable_clks - Enable platform clocks
- * @hpriv: host private area to store config values
- *
- * This function enables all the clks found in hpriv->clks, starting at
- * index 0. If any clk fails to enable it disables all the clks already
- * enabled in reverse order, and then returns an error.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
-{
-	int c, rc;
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
-		rc = clk_prepare_enable(hpriv->clks[c]);
-		if (rc)
-			goto disable_unprepare_clk;
-	}
-	return 0;
-
-disable_unprepare_clk:
-	while (--c >= 0)
-		clk_disable_unprepare(hpriv->clks[c]);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
-
-/**
- * ahci_platform_disable_clks - Disable platform clocks
- * @hpriv: host private area to store config values
- *
- * This function disables all the clks found in hpriv->clks, in reverse
- * order of ahci_platform_enable_clks (starting at the end of the array).
- */
-void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
-{
-	int c;
-
-	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
-		if (hpriv->clks[c])
-			clk_disable_unprepare(hpriv->clks[c]);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
-
-/**
- * ahci_platform_enable_resources - Enable platform resources
- * @hpriv: host private area to store config values
- *
- * This function enables all ahci_platform managed resources in the
- * following order:
- * 1) Regulator
- * 2) Clocks (through ahci_platform_enable_clks)
- * 3) Phy
- *
- * If resource enabling fails at any point the previous enabled resources
- * are disabled in reverse order.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
-{
-	int rc;
-
-	if (hpriv->target_pwr) {
-		rc = regulator_enable(hpriv->target_pwr);
-		if (rc)
-			return rc;
-	}
-
-	rc = ahci_platform_enable_clks(hpriv);
-	if (rc)
-		goto disable_regulator;
-
-	if (hpriv->phy) {
-		rc = phy_init(hpriv->phy);
-		if (rc)
-			goto disable_clks;
-
-		rc = phy_power_on(hpriv->phy);
-		if (rc) {
-			phy_exit(hpriv->phy);
-			goto disable_clks;
-		}
-	}
-
-	return 0;
-
-disable_clks:
-	ahci_platform_disable_clks(hpriv);
-
-disable_regulator:
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
-
-/**
- * ahci_platform_disable_resources - Disable platform resources
- * @hpriv: host private area to store config values
- *
- * This function disables all ahci_platform managed resources in the
- * following order:
- * 1) Phy
- * 2) Clocks (through ahci_platform_disable_clks)
- * 3) Regulator
- */
-void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
-{
-	if (hpriv->phy) {
-		phy_power_off(hpriv->phy);
-		phy_exit(hpriv->phy);
-	}
-
-	ahci_platform_disable_clks(hpriv);
-
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_disable_resources);
-
-static void ahci_platform_put_resources(struct device *dev, void *res)
-{
-	struct ahci_host_priv *hpriv = res;
-	int c;
-
-	if (hpriv->got_runtime_pm) {
-		pm_runtime_put_sync(dev);
-		pm_runtime_disable(dev);
-	}
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
-		clk_put(hpriv->clks[c]);
-}
-
-/**
- * ahci_platform_get_resources - Get platform resources
- * @pdev: platform device to get resources for
- *
- * This function allocates an ahci_host_priv struct, and gets the following
- * resources, storing a reference to them inside the returned struct:
- *
- * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
- * 2) regulator for controlling the targets power (optional)
- * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
- *    or for non devicetree enabled platforms a single clock
- *	4) phy (optional)
- *
- * RETURNS:
- * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
- */
-struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
-{
-	struct device *dev = &pdev->dev;
-	struct ahci_host_priv *hpriv;
-	struct clk *clk;
-	int i, rc = -ENOMEM;
-
-	if (!devres_open_group(dev, NULL, GFP_KERNEL))
-		return ERR_PTR(-ENOMEM);
-
-	hpriv = devres_alloc(ahci_platform_put_resources, sizeof(*hpriv),
-			     GFP_KERNEL);
-	if (!hpriv)
-		goto err_out;
-
-	devres_add(dev, hpriv);
-
-	hpriv->mmio = devm_ioremap_resource(dev,
-			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
-	if (IS_ERR(hpriv->mmio)) {
-		dev_err(dev, "no mmio space\n");
-		rc = PTR_ERR(hpriv->mmio);
-		goto err_out;
-	}
-
-	hpriv->target_pwr = devm_regulator_get_optional(dev, "target");
-	if (IS_ERR(hpriv->target_pwr)) {
-		rc = PTR_ERR(hpriv->target_pwr);
-		if (rc == -EPROBE_DEFER)
-			goto err_out;
-		hpriv->target_pwr = NULL;
-	}
-
-	for (i = 0; i < AHCI_MAX_CLKS; i++) {
-		/*
-		 * For now we must use clk_get(dev, NULL) for the first clock,
-		 * because some platforms (da850, spear13xx) are not yet
-		 * converted to use devicetree for clocks.  For new platforms
-		 * this is equivalent to of_clk_get(dev->of_node, 0).
-		 */
-		if (i == 0)
-			clk = clk_get(dev, NULL);
-		else
-			clk = of_clk_get(dev->of_node, i);
-
-		if (IS_ERR(clk)) {
-			rc = PTR_ERR(clk);
-			if (rc == -EPROBE_DEFER)
-				goto err_out;
-			break;
-		}
-		hpriv->clks[i] = clk;
-	}
-
-	hpriv->phy = devm_phy_get(dev, "sata-phy");
-	if (IS_ERR(hpriv->phy)) {
-		rc = PTR_ERR(hpriv->phy);
-		switch (rc) {
-		case -ENODEV:
-		case -ENOSYS:
-			/* continue normally */
-			hpriv->phy = NULL;
-			break;
-
-		case -EPROBE_DEFER:
-			goto err_out;
-
-		default:
-			dev_err(dev, "couldn't get sata-phy\n");
-			goto err_out;
-		}
-	}
-
-	pm_runtime_enable(dev);
-	pm_runtime_get_sync(dev);
-	hpriv->got_runtime_pm = true;
-
-	devres_remove_group(dev, NULL);
-	return hpriv;
-
-err_out:
-	devres_release_group(dev, NULL);
-	return ERR_PTR(rc);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
-
-/**
- * ahci_platform_init_host - Bring up an ahci-platform host
- * @pdev: platform device pointer for the host
- * @hpriv: ahci-host private data for the host
- * @pi_template: template for the ata_port_info to use
- * @force_port_map: param passed to ahci_save_initial_config
- * @mask_port_map: param passed to ahci_save_initial_config
- *
- * This function does all the usual steps needed to bring up an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
- * must be initialized / enabled before calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_init_host(struct platform_device *pdev,
-			    struct ahci_host_priv *hpriv,
-			    const struct ata_port_info *pi_template,
-			    unsigned int force_port_map,
-			    unsigned int mask_port_map)
-{
-	struct device *dev = &pdev->dev;
-	struct ata_port_info pi = *pi_template;
-	const struct ata_port_info *ppi[] = { &pi, NULL };
-	struct ata_host *host;
-	int i, irq, n_ports, rc;
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0) {
-		dev_err(dev, "no irq\n");
-		return -EINVAL;
-	}
-
-	/* prepare host */
-	hpriv->flags |= (unsigned long)pi.private_data;
-
-	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
-
-	if (hpriv->cap & HOST_CAP_NCQ)
-		pi.flags |= ATA_FLAG_NCQ;
-
-	if (hpriv->cap & HOST_CAP_PMP)
-		pi.flags |= ATA_FLAG_PMP;
-
-	ahci_set_em_messages(hpriv, &pi);
-
-	/* CAP.NP sometimes indicate the index of the last enabled
-	 * port, at other times, that of the last possible port, so
-	 * determining the maximum port number requires looking at
-	 * both CAP.NP and port_map.
-	 */
-	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
-
-	host = ata_host_alloc_pinfo(dev, ppi, n_ports);
-	if (!host)
-		return -ENOMEM;
-
-	host->private_data = hpriv;
-
-	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
-		host->flags |= ATA_HOST_PARALLEL_SCAN;
-	else
-		dev_info(dev, "SSS flag set, parallel bus scan disabled\n");
-
-	if (pi.flags & ATA_FLAG_EM)
-		ahci_reset_em(host);
-
-	for (i = 0; i < host->n_ports; i++) {
-		struct ata_port *ap = host->ports[i];
-
-		ata_port_desc(ap, "mmio %pR",
-			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
-		ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
-
-		/* set enclosure management message type */
-		if (ap->flags & ATA_FLAG_EM)
-			ap->em_message_type = hpriv->em_msg_type;
-
-		/* disabled/not-implemented port */
-		if (!(hpriv->port_map & (1 << i)))
-			ap->ops = &ata_dummy_port_ops;
-	}
-
-	rc = ahci_reset_controller(host);
-	if (rc)
-		return rc;
-
-	ahci_init_controller(host);
-	ahci_print_info(host, "platform");
-
-	return ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
-				 &ahci_platform_sht);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_init_host);
-
 static int ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -420,169 +68,6 @@ disable_resources:
 	return rc;
 }
 
-static void ahci_host_stop(struct ata_host *host)
-{
-	struct device *dev = host->dev;
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-
-	if (pdata && pdata->exit)
-		pdata->exit(dev);
-
-	ahci_platform_disable_resources(hpriv);
-}
-
-#ifdef CONFIG_PM_SLEEP
-/**
- * ahci_platform_suspend_host - Suspend an ahci-platform host
- * @dev: device pointer for the host
- *
- * This function does all the usual steps needed to suspend an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
- * must be disabled after calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_suspend_host(struct device *dev)
-{
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	void __iomem *mmio = hpriv->mmio;
-	u32 ctl;
-
-	if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
-		dev_err(dev, "firmware update required for suspend/resume\n");
-		return -EIO;
-	}
-
-	/*
-	 * AHCI spec rev1.1 section 8.3.3:
-	 * Software must disable interrupts prior to requesting a
-	 * transition of the HBA to D3 state.
-	 */
-	ctl = readl(mmio + HOST_CTL);
-	ctl &= ~HOST_IRQ_EN;
-	writel(ctl, mmio + HOST_CTL);
-	readl(mmio + HOST_CTL); /* flush */
-
-	return ata_host_suspend(host, PMSG_SUSPEND);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
-
-/**
- * ahci_platform_resume_host - Resume an ahci-platform host
- * @dev: device pointer for the host
- *
- * This function does all the usual steps needed to resume an ahci-platform
- * host, note any necessary resources (ie clks, phy, etc.)  must be
- * initialized / enabled before calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_resume_host(struct device *dev)
-{
-	struct ata_host *host = dev_get_drvdata(dev);
-	int rc;
-
-	if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
-		rc = ahci_reset_controller(host);
-		if (rc)
-			return rc;
-
-		ahci_init_controller(host);
-	}
-
-	ata_host_resume(host);
-
-	return 0;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_resume_host);
-
-/**
- * ahci_platform_suspend - Suspend an ahci-platform device
- * @dev: the platform device to suspend
- *
- * This function suspends the host associated with the device, followed by
- * disabling all the resources of the device.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_suspend(struct device *dev)
-{
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	int rc;
-
-	rc = ahci_platform_suspend_host(dev);
-	if (rc)
-		return rc;
-
-	if (pdata && pdata->suspend) {
-		rc = pdata->suspend(dev);
-		if (rc)
-			goto resume_host;
-	}
-
-	ahci_platform_disable_resources(hpriv);
-
-	return 0;
-
-resume_host:
-	ahci_platform_resume_host(dev);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_suspend);
-
-/**
- * ahci_platform_resume - Resume an ahci-platform device
- * @dev: the platform device to resume
- *
- * This function enables all the resources of the device followed by
- * resuming the host associated with the device.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_resume(struct device *dev)
-{
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	int rc;
-
-	rc = ahci_platform_enable_resources(hpriv);
-	if (rc)
-		return rc;
-
-	if (pdata && pdata->resume) {
-		rc = pdata->resume(dev);
-		if (rc)
-			goto disable_resources;
-	}
-
-	rc = ahci_platform_resume_host(dev);
-	if (rc)
-		goto disable_resources;
-
-	/* We resumed so update PM runtime state */
-	pm_runtime_disable(dev);
-	pm_runtime_set_active(dev);
-	pm_runtime_enable(dev);
-
-	return 0;
-
-disable_resources:
-	ahci_platform_disable_resources(hpriv);
-
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_resume);
-#endif
-
 static SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_platform_suspend,
 			 ahci_platform_resume);
 
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
new file mode 100644
index 0000000..7cb3a85
--- /dev/null
+++ b/drivers/ata/libahci_platform.c
@@ -0,0 +1,541 @@
+/*
+ * AHCI SATA platform library
+ *
+ * Copyright 2004-2005  Red Hat, Inc.
+ *   Jeff Garzik <jgarzik-e+AXbWqSrlAAvxtiuMwx3w@public.gmane.org>
+ * Copyright 2010  MontaVista Software, LLC.
+ *   Anton Vorontsov <avorontsov-hkdhdckH98+B+jHODAdFcQ@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/kernel.h>
+#include <linux/gfp.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/pm_runtime.h>
+#include "ahci.h"
+
+static void ahci_host_stop(struct ata_host *host);
+
+struct ata_port_operations ahci_platform_ops = {
+	.inherits	= &ahci_ops,
+	.host_stop	= ahci_host_stop,
+};
+EXPORT_SYMBOL_GPL(ahci_platform_ops);
+
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT("ahci_platform"),
+};
+
+/**
+ * ahci_platform_enable_clks - Enable platform clocks
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all the clks found in hpriv->clks, starting at
+ * index 0. If any clk fails to enable it disables all the clks already
+ * enabled in reverse order, and then returns an error.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
+{
+	int c, rc;
+
+	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
+		rc = clk_prepare_enable(hpriv->clks[c]);
+		if (rc)
+			goto disable_unprepare_clk;
+	}
+	return 0;
+
+disable_unprepare_clk:
+	while (--c >= 0)
+		clk_disable_unprepare(hpriv->clks[c]);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
+
+/**
+ * ahci_platform_disable_clks - Disable platform clocks
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all the clks found in hpriv->clks, in reverse
+ * order of ahci_platform_enable_clks (starting at the end of the array).
+ */
+void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
+{
+	int c;
+
+	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
+		if (hpriv->clks[c])
+			clk_disable_unprepare(hpriv->clks[c]);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
+
+/**
+ * ahci_platform_enable_resources - Enable platform resources
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all ahci_platform managed resources in the
+ * following order:
+ * 1) Regulator
+ * 2) Clocks (through ahci_platform_enable_clks)
+ * 3) Phy
+ *
+ * If resource enabling fails at any point the previous enabled resources
+ * are disabled in reverse order.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
+{
+	int rc;
+
+	if (hpriv->target_pwr) {
+		rc = regulator_enable(hpriv->target_pwr);
+		if (rc)
+			return rc;
+	}
+
+	rc = ahci_platform_enable_clks(hpriv);
+	if (rc)
+		goto disable_regulator;
+
+	if (hpriv->phy) {
+		rc = phy_init(hpriv->phy);
+		if (rc)
+			goto disable_clks;
+
+		rc = phy_power_on(hpriv->phy);
+		if (rc) {
+			phy_exit(hpriv->phy);
+			goto disable_clks;
+		}
+	}
+
+	return 0;
+
+disable_clks:
+	ahci_platform_disable_clks(hpriv);
+
+disable_regulator:
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
+
+/**
+ * ahci_platform_disable_resources - Disable platform resources
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all ahci_platform managed resources in the
+ * following order:
+ * 1) Phy
+ * 2) Clocks (through ahci_platform_disable_clks)
+ * 3) Regulator
+ */
+void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
+{
+	if (hpriv->phy) {
+		phy_power_off(hpriv->phy);
+		phy_exit(hpriv->phy);
+	}
+
+	ahci_platform_disable_clks(hpriv);
+
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_resources);
+
+static void ahci_platform_put_resources(struct device *dev, void *res)
+{
+	struct ahci_host_priv *hpriv = res;
+	int c;
+
+	if (hpriv->got_runtime_pm) {
+		pm_runtime_put_sync(dev);
+		pm_runtime_disable(dev);
+	}
+
+	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
+		clk_put(hpriv->clks[c]);
+}
+
+/**
+ * ahci_platform_get_resources - Get platform resources
+ * @pdev: platform device to get resources for
+ *
+ * This function allocates an ahci_host_priv struct, and gets the following
+ * resources, storing a reference to them inside the returned struct:
+ *
+ * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
+ * 2) regulator for controlling the targets power (optional)
+ * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
+ *    or for non devicetree enabled platforms a single clock
+ *	4) phy (optional)
+ *
+ * RETURNS:
+ * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
+ */
+struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct clk *clk;
+	int i, rc = -ENOMEM;
+
+	if (!devres_open_group(dev, NULL, GFP_KERNEL))
+		return ERR_PTR(-ENOMEM);
+
+	hpriv = devres_alloc(ahci_platform_put_resources, sizeof(*hpriv),
+			     GFP_KERNEL);
+	if (!hpriv)
+		goto err_out;
+
+	devres_add(dev, hpriv);
+
+	hpriv->mmio = devm_ioremap_resource(dev,
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+	if (IS_ERR(hpriv->mmio)) {
+		dev_err(dev, "no mmio space\n");
+		rc = PTR_ERR(hpriv->mmio);
+		goto err_out;
+	}
+
+	hpriv->target_pwr = devm_regulator_get_optional(dev, "target");
+	if (IS_ERR(hpriv->target_pwr)) {
+		rc = PTR_ERR(hpriv->target_pwr);
+		if (rc == -EPROBE_DEFER)
+			goto err_out;
+		hpriv->target_pwr = NULL;
+	}
+
+	for (i = 0; i < AHCI_MAX_CLKS; i++) {
+		/*
+		 * For now we must use clk_get(dev, NULL) for the first clock,
+		 * because some platforms (da850, spear13xx) are not yet
+		 * converted to use devicetree for clocks.  For new platforms
+		 * this is equivalent to of_clk_get(dev->of_node, 0).
+		 */
+		if (i == 0)
+			clk = clk_get(dev, NULL);
+		else
+			clk = of_clk_get(dev->of_node, i);
+
+		if (IS_ERR(clk)) {
+			rc = PTR_ERR(clk);
+			if (rc == -EPROBE_DEFER)
+				goto err_out;
+			break;
+		}
+		hpriv->clks[i] = clk;
+	}
+
+	hpriv->phy = devm_phy_get(dev, "sata-phy");
+	if (IS_ERR(hpriv->phy)) {
+		rc = PTR_ERR(hpriv->phy);
+		switch (rc) {
+		case -ENODEV:
+		case -ENOSYS:
+			/* continue normally */
+			hpriv->phy = NULL;
+			break;
+
+		case -EPROBE_DEFER:
+			goto err_out;
+
+		default:
+			dev_err(dev, "couldn't get sata-phy\n");
+			goto err_out;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+	hpriv->got_runtime_pm = true;
+
+	devres_remove_group(dev, NULL);
+	return hpriv;
+
+err_out:
+	devres_release_group(dev, NULL);
+	return ERR_PTR(rc);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
+
+/**
+ * ahci_platform_init_host - Bring up an ahci-platform host
+ * @pdev: platform device pointer for the host
+ * @hpriv: ahci-host private data for the host
+ * @pi_template: template for the ata_port_info to use
+ * @force_port_map: param passed to ahci_save_initial_config
+ * @mask_port_map: param passed to ahci_save_initial_config
+ *
+ * This function does all the usual steps needed to bring up an
+ * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * must be initialized / enabled before calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_init_host(struct platform_device *pdev,
+			    struct ahci_host_priv *hpriv,
+			    const struct ata_port_info *pi_template,
+			    unsigned int force_port_map,
+			    unsigned int mask_port_map)
+{
+	struct device *dev = &pdev->dev;
+	struct ata_port_info pi = *pi_template;
+	const struct ata_port_info *ppi[] = { &pi, NULL };
+	struct ata_host *host;
+	int i, irq, n_ports, rc;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		dev_err(dev, "no irq\n");
+		return -EINVAL;
+	}
+
+	/* prepare host */
+	hpriv->flags |= (unsigned long)pi.private_data;
+
+	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
+
+	if (hpriv->cap & HOST_CAP_NCQ)
+		pi.flags |= ATA_FLAG_NCQ;
+
+	if (hpriv->cap & HOST_CAP_PMP)
+		pi.flags |= ATA_FLAG_PMP;
+
+	ahci_set_em_messages(hpriv, &pi);
+
+	/* CAP.NP sometimes indicate the index of the last enabled
+	 * port, at other times, that of the last possible port, so
+	 * determining the maximum port number requires looking at
+	 * both CAP.NP and port_map.
+	 */
+	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+	host = ata_host_alloc_pinfo(dev, ppi, n_ports);
+	if (!host)
+		return -ENOMEM;
+
+	host->private_data = hpriv;
+
+	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
+		host->flags |= ATA_HOST_PARALLEL_SCAN;
+	else
+		dev_info(dev, "SSS flag set, parallel bus scan disabled\n");
+
+	if (pi.flags & ATA_FLAG_EM)
+		ahci_reset_em(host);
+
+	for (i = 0; i < host->n_ports; i++) {
+		struct ata_port *ap = host->ports[i];
+
+		ata_port_desc(ap, "mmio %pR",
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+		ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
+
+		/* set enclosure management message type */
+		if (ap->flags & ATA_FLAG_EM)
+			ap->em_message_type = hpriv->em_msg_type;
+
+		/* disabled/not-implemented port */
+		if (!(hpriv->port_map & (1 << i)))
+			ap->ops = &ata_dummy_port_ops;
+	}
+
+	rc = ahci_reset_controller(host);
+	if (rc)
+		return rc;
+
+	ahci_init_controller(host);
+	ahci_print_info(host, "platform");
+
+	return ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
+				 &ahci_platform_sht);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_init_host);
+
+static void ahci_host_stop(struct ata_host *host)
+{
+	struct device *dev = host->dev;
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+
+	if (pdata && pdata->exit)
+		pdata->exit(dev);
+
+	ahci_platform_disable_resources(hpriv);
+}
+
+#ifdef CONFIG_PM_SLEEP
+/**
+ * ahci_platform_suspend_host - Suspend an ahci-platform host
+ * @dev: device pointer for the host
+ *
+ * This function does all the usual steps needed to suspend an
+ * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * must be disabled after calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_suspend_host(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	void __iomem *mmio = hpriv->mmio;
+	u32 ctl;
+
+	if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
+		dev_err(dev, "firmware update required for suspend/resume\n");
+		return -EIO;
+	}
+
+	/*
+	 * AHCI spec rev1.1 section 8.3.3:
+	 * Software must disable interrupts prior to requesting a
+	 * transition of the HBA to D3 state.
+	 */
+	ctl = readl(mmio + HOST_CTL);
+	ctl &= ~HOST_IRQ_EN;
+	writel(ctl, mmio + HOST_CTL);
+	readl(mmio + HOST_CTL); /* flush */
+
+	return ata_host_suspend(host, PMSG_SUSPEND);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
+
+/**
+ * ahci_platform_resume_host - Resume an ahci-platform host
+ * @dev: device pointer for the host
+ *
+ * This function does all the usual steps needed to resume an ahci-platform
+ * host, note any necessary resources (ie clks, phy, etc.)  must be
+ * initialized / enabled before calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_resume_host(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	int rc;
+
+	if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
+		rc = ahci_reset_controller(host);
+		if (rc)
+			return rc;
+
+		ahci_init_controller(host);
+	}
+
+	ata_host_resume(host);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_resume_host);
+
+/**
+ * ahci_platform_suspend - Suspend an ahci-platform device
+ * @dev: the platform device to suspend
+ *
+ * This function suspends the host associated with the device, followed by
+ * disabling all the resources of the device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_suspend(struct device *dev)
+{
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_suspend_host(dev);
+	if (rc)
+		return rc;
+
+	if (pdata && pdata->suspend) {
+		rc = pdata->suspend(dev);
+		if (rc)
+			goto resume_host;
+	}
+
+	ahci_platform_disable_resources(hpriv);
+
+	return 0;
+
+resume_host:
+	ahci_platform_resume_host(dev);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_suspend);
+
+/**
+ * ahci_platform_resume - Resume an ahci-platform device
+ * @dev: the platform device to resume
+ *
+ * This function enables all the resources of the device followed by
+ * resuming the host associated with the device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_resume(struct device *dev)
+{
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	if (pdata && pdata->resume) {
+		rc = pdata->resume(dev);
+		if (rc)
+			goto disable_resources;
+	}
+
+	rc = ahci_platform_resume_host(dev);
+	if (rc)
+		goto disable_resources;
+
+	/* We resumed so update PM runtime state */
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
+
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_resume);
+#endif
+
+MODULE_DESCRIPTION("AHCI SATA platform library");
+MODULE_AUTHOR("Anton Vorontsov <avorontsov-hkdhdckH98+B+jHODAdFcQ@public.gmane.org>");
+MODULE_LICENSE("GPL");
-- 
1.8.2.3

[PATCH v3 2/4] ata: move library code from ahci_platform.c to libahci_platform.c

[Bartlomiej Zolnierkiewicz]

Move AHCI platform library code from ahci_platform.c to
libahci_platform.c and fix dependencies for ahci_st,
ahci_imx and ahci_sunxi drivers.

Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- no changes
v2:
- updated patch description

 drivers/ata/Kconfig            |   5 +-
 drivers/ata/Makefile           |   8 +-
 drivers/ata/ahci_platform.c    | 515 ---------------------------------------
 drivers/ata/libahci_platform.c | 541 +++++++++++++++++++++++++++++++++++++++++
 4 files changed, 547 insertions(+), 522 deletions(-)
 create mode 100644 drivers/ata/libahci_platform.c

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index c4db48c..371e8890 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -99,7 +99,6 @@ config SATA_AHCI_PLATFORM
 
 config AHCI_ST
 	tristate "ST AHCI SATA support"
-	depends on SATA_AHCI_PLATFORM
 	depends on ARCH_STI
 	help
 	  This option enables support for ST AHCI SATA controller.
@@ -108,7 +107,7 @@ config AHCI_ST
 
 config AHCI_IMX
 	tristate "Freescale i.MX AHCI SATA support"
-	depends on SATA_AHCI_PLATFORM && MFD_SYSCON
+	depends on MFD_SYSCON
 	help
 	  This option enables support for the Freescale i.MX SoC's
 	  onboard AHCI SATA.
@@ -117,7 +116,7 @@ config AHCI_IMX
 
 config AHCI_SUNXI
 	tristate "Allwinner sunxi AHCI SATA support"
-	depends on ARCH_SUNXI && SATA_AHCI_PLATFORM
+	depends on ARCH_SUNXI
 	help
 	  This option enables support for the Allwinner sunxi SoC's
 	  onboard AHCI SATA.
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index e20148c..6123e64 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -4,15 +4,15 @@ obj-$(CONFIG_ATA)		+= libata.o
 # non-SFF interface
 obj-$(CONFIG_SATA_AHCI)		+= ahci.o libahci.o
 obj-$(CONFIG_SATA_ACARD_AHCI)	+= acard-ahci.o libahci.o
-obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o
+obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o libahci_platform.o
 obj-$(CONFIG_SATA_FSL)		+= sata_fsl.o
 obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
-obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o
-obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o
-obj-$(CONFIG_AHCI_ST)		+= ahci_st.o
+obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
 
 # SFF w/ custom DMA
 obj-$(CONFIG_PDC_ADMA)		+= pdc_adma.o
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 7bd6adf..ef67e79 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -12,28 +12,15 @@
  * any later version.
  */
 
-#include <linux/clk.h>
 #include <linux/kernel.h>
-#include <linux/gfp.h>
 #include <linux/module.h>
 #include <linux/pm.h>
-#include <linux/interrupt.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/libata.h>
 #include <linux/ahci_platform.h>
-#include <linux/phy/phy.h>
-#include <linux/pm_runtime.h>
 #include "ahci.h"
 
-static void ahci_host_stop(struct ata_host *host);
-
-struct ata_port_operations ahci_platform_ops = {
-	.inherits	= &ahci_ops,
-	.host_stop	= ahci_host_stop,
-};
-EXPORT_SYMBOL_GPL(ahci_platform_ops);
-
 static const struct ata_port_info ahci_port_info = {
 	.flags		= AHCI_FLAG_COMMON,
 	.pio_mask	= ATA_PIO4,
@@ -41,345 +28,6 @@ static const struct ata_port_info ahci_port_info = {
 	.port_ops	= &ahci_platform_ops,
 };
 
-static struct scsi_host_template ahci_platform_sht = {
-	AHCI_SHT("ahci_platform"),
-};
-
-/**
- * ahci_platform_enable_clks - Enable platform clocks
- * @hpriv: host private area to store config values
- *
- * This function enables all the clks found in hpriv->clks, starting at
- * index 0. If any clk fails to enable it disables all the clks already
- * enabled in reverse order, and then returns an error.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
-{
-	int c, rc;
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
-		rc = clk_prepare_enable(hpriv->clks[c]);
-		if (rc)
-			goto disable_unprepare_clk;
-	}
-	return 0;
-
-disable_unprepare_clk:
-	while (--c >= 0)
-		clk_disable_unprepare(hpriv->clks[c]);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
-
-/**
- * ahci_platform_disable_clks - Disable platform clocks
- * @hpriv: host private area to store config values
- *
- * This function disables all the clks found in hpriv->clks, in reverse
- * order of ahci_platform_enable_clks (starting at the end of the array).
- */
-void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
-{
-	int c;
-
-	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
-		if (hpriv->clks[c])
-			clk_disable_unprepare(hpriv->clks[c]);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
-
-/**
- * ahci_platform_enable_resources - Enable platform resources
- * @hpriv: host private area to store config values
- *
- * This function enables all ahci_platform managed resources in the
- * following order:
- * 1) Regulator
- * 2) Clocks (through ahci_platform_enable_clks)
- * 3) Phy
- *
- * If resource enabling fails at any point the previous enabled resources
- * are disabled in reverse order.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
-{
-	int rc;
-
-	if (hpriv->target_pwr) {
-		rc = regulator_enable(hpriv->target_pwr);
-		if (rc)
-			return rc;
-	}
-
-	rc = ahci_platform_enable_clks(hpriv);
-	if (rc)
-		goto disable_regulator;
-
-	if (hpriv->phy) {
-		rc = phy_init(hpriv->phy);
-		if (rc)
-			goto disable_clks;
-
-		rc = phy_power_on(hpriv->phy);
-		if (rc) {
-			phy_exit(hpriv->phy);
-			goto disable_clks;
-		}
-	}
-
-	return 0;
-
-disable_clks:
-	ahci_platform_disable_clks(hpriv);
-
-disable_regulator:
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
-
-/**
- * ahci_platform_disable_resources - Disable platform resources
- * @hpriv: host private area to store config values
- *
- * This function disables all ahci_platform managed resources in the
- * following order:
- * 1) Phy
- * 2) Clocks (through ahci_platform_disable_clks)
- * 3) Regulator
- */
-void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
-{
-	if (hpriv->phy) {
-		phy_power_off(hpriv->phy);
-		phy_exit(hpriv->phy);
-	}
-
-	ahci_platform_disable_clks(hpriv);
-
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_disable_resources);
-
-static void ahci_platform_put_resources(struct device *dev, void *res)
-{
-	struct ahci_host_priv *hpriv = res;
-	int c;
-
-	if (hpriv->got_runtime_pm) {
-		pm_runtime_put_sync(dev);
-		pm_runtime_disable(dev);
-	}
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
-		clk_put(hpriv->clks[c]);
-}
-
-/**
- * ahci_platform_get_resources - Get platform resources
- * @pdev: platform device to get resources for
- *
- * This function allocates an ahci_host_priv struct, and gets the following
- * resources, storing a reference to them inside the returned struct:
- *
- * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
- * 2) regulator for controlling the targets power (optional)
- * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
- *    or for non devicetree enabled platforms a single clock
- *	4) phy (optional)
- *
- * RETURNS:
- * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
- */
-struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
-{
-	struct device *dev = &pdev->dev;
-	struct ahci_host_priv *hpriv;
-	struct clk *clk;
-	int i, rc = -ENOMEM;
-
-	if (!devres_open_group(dev, NULL, GFP_KERNEL))
-		return ERR_PTR(-ENOMEM);
-
-	hpriv = devres_alloc(ahci_platform_put_resources, sizeof(*hpriv),
-			     GFP_KERNEL);
-	if (!hpriv)
-		goto err_out;
-
-	devres_add(dev, hpriv);
-
-	hpriv->mmio = devm_ioremap_resource(dev,
-			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
-	if (IS_ERR(hpriv->mmio)) {
-		dev_err(dev, "no mmio space\n");
-		rc = PTR_ERR(hpriv->mmio);
-		goto err_out;
-	}
-
-	hpriv->target_pwr = devm_regulator_get_optional(dev, "target");
-	if (IS_ERR(hpriv->target_pwr)) {
-		rc = PTR_ERR(hpriv->target_pwr);
-		if (rc == -EPROBE_DEFER)
-			goto err_out;
-		hpriv->target_pwr = NULL;
-	}
-
-	for (i = 0; i < AHCI_MAX_CLKS; i++) {
-		/*
-		 * For now we must use clk_get(dev, NULL) for the first clock,
-		 * because some platforms (da850, spear13xx) are not yet
-		 * converted to use devicetree for clocks.  For new platforms
-		 * this is equivalent to of_clk_get(dev->of_node, 0).
-		 */
-		if (i == 0)
-			clk = clk_get(dev, NULL);
-		else
-			clk = of_clk_get(dev->of_node, i);
-
-		if (IS_ERR(clk)) {
-			rc = PTR_ERR(clk);
-			if (rc == -EPROBE_DEFER)
-				goto err_out;
-			break;
-		}
-		hpriv->clks[i] = clk;
-	}
-
-	hpriv->phy = devm_phy_get(dev, "sata-phy");
-	if (IS_ERR(hpriv->phy)) {
-		rc = PTR_ERR(hpriv->phy);
-		switch (rc) {
-		case -ENODEV:
-		case -ENOSYS:
-			/* continue normally */
-			hpriv->phy = NULL;
-			break;
-
-		case -EPROBE_DEFER:
-			goto err_out;
-
-		default:
-			dev_err(dev, "couldn't get sata-phy\n");
-			goto err_out;
-		}
-	}
-
-	pm_runtime_enable(dev);
-	pm_runtime_get_sync(dev);
-	hpriv->got_runtime_pm = true;
-
-	devres_remove_group(dev, NULL);
-	return hpriv;
-
-err_out:
-	devres_release_group(dev, NULL);
-	return ERR_PTR(rc);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
-
-/**
- * ahci_platform_init_host - Bring up an ahci-platform host
- * @pdev: platform device pointer for the host
- * @hpriv: ahci-host private data for the host
- * @pi_template: template for the ata_port_info to use
- * @force_port_map: param passed to ahci_save_initial_config
- * @mask_port_map: param passed to ahci_save_initial_config
- *
- * This function does all the usual steps needed to bring up an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
- * must be initialized / enabled before calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_init_host(struct platform_device *pdev,
-			    struct ahci_host_priv *hpriv,
-			    const struct ata_port_info *pi_template,
-			    unsigned int force_port_map,
-			    unsigned int mask_port_map)
-{
-	struct device *dev = &pdev->dev;
-	struct ata_port_info pi = *pi_template;
-	const struct ata_port_info *ppi[] = { &pi, NULL };
-	struct ata_host *host;
-	int i, irq, n_ports, rc;
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0) {
-		dev_err(dev, "no irq\n");
-		return -EINVAL;
-	}
-
-	/* prepare host */
-	hpriv->flags |= (unsigned long)pi.private_data;
-
-	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
-
-	if (hpriv->cap & HOST_CAP_NCQ)
-		pi.flags |= ATA_FLAG_NCQ;
-
-	if (hpriv->cap & HOST_CAP_PMP)
-		pi.flags |= ATA_FLAG_PMP;
-
-	ahci_set_em_messages(hpriv, &pi);
-
-	/* CAP.NP sometimes indicate the index of the last enabled
-	 * port, at other times, that of the last possible port, so
-	 * determining the maximum port number requires looking at
-	 * both CAP.NP and port_map.
-	 */
-	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
-
-	host = ata_host_alloc_pinfo(dev, ppi, n_ports);
-	if (!host)
-		return -ENOMEM;
-
-	host->private_data = hpriv;
-
-	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
-		host->flags |= ATA_HOST_PARALLEL_SCAN;
-	else
-		dev_info(dev, "SSS flag set, parallel bus scan disabled\n");
-
-	if (pi.flags & ATA_FLAG_EM)
-		ahci_reset_em(host);
-
-	for (i = 0; i < host->n_ports; i++) {
-		struct ata_port *ap = host->ports[i];
-
-		ata_port_desc(ap, "mmio %pR",
-			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
-		ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
-
-		/* set enclosure management message type */
-		if (ap->flags & ATA_FLAG_EM)
-			ap->em_message_type = hpriv->em_msg_type;
-
-		/* disabled/not-implemented port */
-		if (!(hpriv->port_map & (1 << i)))
-			ap->ops = &ata_dummy_port_ops;
-	}
-
-	rc = ahci_reset_controller(host);
-	if (rc)
-		return rc;
-
-	ahci_init_controller(host);
-	ahci_print_info(host, "platform");
-
-	return ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
-				 &ahci_platform_sht);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_init_host);
-
 static int ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -420,169 +68,6 @@ disable_resources:
 	return rc;
 }
 
-static void ahci_host_stop(struct ata_host *host)
-{
-	struct device *dev = host->dev;
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-
-	if (pdata && pdata->exit)
-		pdata->exit(dev);
-
-	ahci_platform_disable_resources(hpriv);
-}
-
-#ifdef CONFIG_PM_SLEEP
-/**
- * ahci_platform_suspend_host - Suspend an ahci-platform host
- * @dev: device pointer for the host
- *
- * This function does all the usual steps needed to suspend an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
- * must be disabled after calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_suspend_host(struct device *dev)
-{
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	void __iomem *mmio = hpriv->mmio;
-	u32 ctl;
-
-	if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
-		dev_err(dev, "firmware update required for suspend/resume\n");
-		return -EIO;
-	}
-
-	/*
-	 * AHCI spec rev1.1 section 8.3.3:
-	 * Software must disable interrupts prior to requesting a
-	 * transition of the HBA to D3 state.
-	 */
-	ctl = readl(mmio + HOST_CTL);
-	ctl &= ~HOST_IRQ_EN;
-	writel(ctl, mmio + HOST_CTL);
-	readl(mmio + HOST_CTL); /* flush */
-
-	return ata_host_suspend(host, PMSG_SUSPEND);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
-
-/**
- * ahci_platform_resume_host - Resume an ahci-platform host
- * @dev: device pointer for the host
- *
- * This function does all the usual steps needed to resume an ahci-platform
- * host, note any necessary resources (ie clks, phy, etc.)  must be
- * initialized / enabled before calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_resume_host(struct device *dev)
-{
-	struct ata_host *host = dev_get_drvdata(dev);
-	int rc;
-
-	if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
-		rc = ahci_reset_controller(host);
-		if (rc)
-			return rc;
-
-		ahci_init_controller(host);
-	}
-
-	ata_host_resume(host);
-
-	return 0;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_resume_host);
-
-/**
- * ahci_platform_suspend - Suspend an ahci-platform device
- * @dev: the platform device to suspend
- *
- * This function suspends the host associated with the device, followed by
- * disabling all the resources of the device.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_suspend(struct device *dev)
-{
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	int rc;
-
-	rc = ahci_platform_suspend_host(dev);
-	if (rc)
-		return rc;
-
-	if (pdata && pdata->suspend) {
-		rc = pdata->suspend(dev);
-		if (rc)
-			goto resume_host;
-	}
-
-	ahci_platform_disable_resources(hpriv);
-
-	return 0;
-
-resume_host:
-	ahci_platform_resume_host(dev);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_suspend);
-
-/**
- * ahci_platform_resume - Resume an ahci-platform device
- * @dev: the platform device to resume
- *
- * This function enables all the resources of the device followed by
- * resuming the host associated with the device.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_resume(struct device *dev)
-{
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	int rc;
-
-	rc = ahci_platform_enable_resources(hpriv);
-	if (rc)
-		return rc;
-
-	if (pdata && pdata->resume) {
-		rc = pdata->resume(dev);
-		if (rc)
-			goto disable_resources;
-	}
-
-	rc = ahci_platform_resume_host(dev);
-	if (rc)
-		goto disable_resources;
-
-	/* We resumed so update PM runtime state */
-	pm_runtime_disable(dev);
-	pm_runtime_set_active(dev);
-	pm_runtime_enable(dev);
-
-	return 0;
-
-disable_resources:
-	ahci_platform_disable_resources(hpriv);
-
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_resume);
-#endif
-
 static SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_platform_suspend,
 			 ahci_platform_resume);
 
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
new file mode 100644
index 0000000..7cb3a85
--- /dev/null
+++ b/drivers/ata/libahci_platform.c
@@ -0,0 +1,541 @@
+/*
+ * AHCI SATA platform library
+ *
+ * Copyright 2004-2005  Red Hat, Inc.
+ *   Jeff Garzik <jgarzik@pobox.com>
+ * Copyright 2010  MontaVista Software, LLC.
+ *   Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/kernel.h>
+#include <linux/gfp.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/pm_runtime.h>
+#include "ahci.h"
+
+static void ahci_host_stop(struct ata_host *host);
+
+struct ata_port_operations ahci_platform_ops = {
+	.inherits	= &ahci_ops,
+	.host_stop	= ahci_host_stop,
+};
+EXPORT_SYMBOL_GPL(ahci_platform_ops);
+
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT("ahci_platform"),
+};
+
+/**
+ * ahci_platform_enable_clks - Enable platform clocks
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all the clks found in hpriv->clks, starting at
+ * index 0. If any clk fails to enable it disables all the clks already
+ * enabled in reverse order, and then returns an error.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
+{
+	int c, rc;
+
+	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
+		rc = clk_prepare_enable(hpriv->clks[c]);
+		if (rc)
+			goto disable_unprepare_clk;
+	}
+	return 0;
+
+disable_unprepare_clk:
+	while (--c >= 0)
+		clk_disable_unprepare(hpriv->clks[c]);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
+
+/**
+ * ahci_platform_disable_clks - Disable platform clocks
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all the clks found in hpriv->clks, in reverse
+ * order of ahci_platform_enable_clks (starting at the end of the array).
+ */
+void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
+{
+	int c;
+
+	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
+		if (hpriv->clks[c])
+			clk_disable_unprepare(hpriv->clks[c]);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
+
+/**
+ * ahci_platform_enable_resources - Enable platform resources
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all ahci_platform managed resources in the
+ * following order:
+ * 1) Regulator
+ * 2) Clocks (through ahci_platform_enable_clks)
+ * 3) Phy
+ *
+ * If resource enabling fails at any point the previous enabled resources
+ * are disabled in reverse order.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
+{
+	int rc;
+
+	if (hpriv->target_pwr) {
+		rc = regulator_enable(hpriv->target_pwr);
+		if (rc)
+			return rc;
+	}
+
+	rc = ahci_platform_enable_clks(hpriv);
+	if (rc)
+		goto disable_regulator;
+
+	if (hpriv->phy) {
+		rc = phy_init(hpriv->phy);
+		if (rc)
+			goto disable_clks;
+
+		rc = phy_power_on(hpriv->phy);
+		if (rc) {
+			phy_exit(hpriv->phy);
+			goto disable_clks;
+		}
+	}
+
+	return 0;
+
+disable_clks:
+	ahci_platform_disable_clks(hpriv);
+
+disable_regulator:
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
+
+/**
+ * ahci_platform_disable_resources - Disable platform resources
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all ahci_platform managed resources in the
+ * following order:
+ * 1) Phy
+ * 2) Clocks (through ahci_platform_disable_clks)
+ * 3) Regulator
+ */
+void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
+{
+	if (hpriv->phy) {
+		phy_power_off(hpriv->phy);
+		phy_exit(hpriv->phy);
+	}
+
+	ahci_platform_disable_clks(hpriv);
+
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_resources);
+
+static void ahci_platform_put_resources(struct device *dev, void *res)
+{
+	struct ahci_host_priv *hpriv = res;
+	int c;
+
+	if (hpriv->got_runtime_pm) {
+		pm_runtime_put_sync(dev);
+		pm_runtime_disable(dev);
+	}
+
+	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
+		clk_put(hpriv->clks[c]);
+}
+
+/**
+ * ahci_platform_get_resources - Get platform resources
+ * @pdev: platform device to get resources for
+ *
+ * This function allocates an ahci_host_priv struct, and gets the following
+ * resources, storing a reference to them inside the returned struct:
+ *
+ * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
+ * 2) regulator for controlling the targets power (optional)
+ * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
+ *    or for non devicetree enabled platforms a single clock
+ *	4) phy (optional)
+ *
+ * RETURNS:
+ * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
+ */
+struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct clk *clk;
+	int i, rc = -ENOMEM;
+
+	if (!devres_open_group(dev, NULL, GFP_KERNEL))
+		return ERR_PTR(-ENOMEM);
+
+	hpriv = devres_alloc(ahci_platform_put_resources, sizeof(*hpriv),
+			     GFP_KERNEL);
+	if (!hpriv)
+		goto err_out;
+
+	devres_add(dev, hpriv);
+
+	hpriv->mmio = devm_ioremap_resource(dev,
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+	if (IS_ERR(hpriv->mmio)) {
+		dev_err(dev, "no mmio space\n");
+		rc = PTR_ERR(hpriv->mmio);
+		goto err_out;
+	}
+
+	hpriv->target_pwr = devm_regulator_get_optional(dev, "target");
+	if (IS_ERR(hpriv->target_pwr)) {
+		rc = PTR_ERR(hpriv->target_pwr);
+		if (rc == -EPROBE_DEFER)
+			goto err_out;
+		hpriv->target_pwr = NULL;
+	}
+
+	for (i = 0; i < AHCI_MAX_CLKS; i++) {
+		/*
+		 * For now we must use clk_get(dev, NULL) for the first clock,
+		 * because some platforms (da850, spear13xx) are not yet
+		 * converted to use devicetree for clocks.  For new platforms
+		 * this is equivalent to of_clk_get(dev->of_node, 0).
+		 */
+		if (i == 0)
+			clk = clk_get(dev, NULL);
+		else
+			clk = of_clk_get(dev->of_node, i);
+
+		if (IS_ERR(clk)) {
+			rc = PTR_ERR(clk);
+			if (rc == -EPROBE_DEFER)
+				goto err_out;
+			break;
+		}
+		hpriv->clks[i] = clk;
+	}
+
+	hpriv->phy = devm_phy_get(dev, "sata-phy");
+	if (IS_ERR(hpriv->phy)) {
+		rc = PTR_ERR(hpriv->phy);
+		switch (rc) {
+		case -ENODEV:
+		case -ENOSYS:
+			/* continue normally */
+			hpriv->phy = NULL;
+			break;
+
+		case -EPROBE_DEFER:
+			goto err_out;
+
+		default:
+			dev_err(dev, "couldn't get sata-phy\n");
+			goto err_out;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+	hpriv->got_runtime_pm = true;
+
+	devres_remove_group(dev, NULL);
+	return hpriv;
+
+err_out:
+	devres_release_group(dev, NULL);
+	return ERR_PTR(rc);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
+
+/**
+ * ahci_platform_init_host - Bring up an ahci-platform host
+ * @pdev: platform device pointer for the host
+ * @hpriv: ahci-host private data for the host
+ * @pi_template: template for the ata_port_info to use
+ * @force_port_map: param passed to ahci_save_initial_config
+ * @mask_port_map: param passed to ahci_save_initial_config
+ *
+ * This function does all the usual steps needed to bring up an
+ * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * must be initialized / enabled before calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_init_host(struct platform_device *pdev,
+			    struct ahci_host_priv *hpriv,
+			    const struct ata_port_info *pi_template,
+			    unsigned int force_port_map,
+			    unsigned int mask_port_map)
+{
+	struct device *dev = &pdev->dev;
+	struct ata_port_info pi = *pi_template;
+	const struct ata_port_info *ppi[] = { &pi, NULL };
+	struct ata_host *host;
+	int i, irq, n_ports, rc;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		dev_err(dev, "no irq\n");
+		return -EINVAL;
+	}
+
+	/* prepare host */
+	hpriv->flags |= (unsigned long)pi.private_data;
+
+	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
+
+	if (hpriv->cap & HOST_CAP_NCQ)
+		pi.flags |= ATA_FLAG_NCQ;
+
+	if (hpriv->cap & HOST_CAP_PMP)
+		pi.flags |= ATA_FLAG_PMP;
+
+	ahci_set_em_messages(hpriv, &pi);
+
+	/* CAP.NP sometimes indicate the index of the last enabled
+	 * port, at other times, that of the last possible port, so
+	 * determining the maximum port number requires looking at
+	 * both CAP.NP and port_map.
+	 */
+	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+	host = ata_host_alloc_pinfo(dev, ppi, n_ports);
+	if (!host)
+		return -ENOMEM;
+
+	host->private_data = hpriv;
+
+	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
+		host->flags |= ATA_HOST_PARALLEL_SCAN;
+	else
+		dev_info(dev, "SSS flag set, parallel bus scan disabled\n");
+
+	if (pi.flags & ATA_FLAG_EM)
+		ahci_reset_em(host);
+
+	for (i = 0; i < host->n_ports; i++) {
+		struct ata_port *ap = host->ports[i];
+
+		ata_port_desc(ap, "mmio %pR",
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+		ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
+
+		/* set enclosure management message type */
+		if (ap->flags & ATA_FLAG_EM)
+			ap->em_message_type = hpriv->em_msg_type;
+
+		/* disabled/not-implemented port */
+		if (!(hpriv->port_map & (1 << i)))
+			ap->ops = &ata_dummy_port_ops;
+	}
+
+	rc = ahci_reset_controller(host);
+	if (rc)
+		return rc;
+
+	ahci_init_controller(host);
+	ahci_print_info(host, "platform");
+
+	return ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
+				 &ahci_platform_sht);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_init_host);
+
+static void ahci_host_stop(struct ata_host *host)
+{
+	struct device *dev = host->dev;
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+
+	if (pdata && pdata->exit)
+		pdata->exit(dev);
+
+	ahci_platform_disable_resources(hpriv);
+}
+
+#ifdef CONFIG_PM_SLEEP
+/**
+ * ahci_platform_suspend_host - Suspend an ahci-platform host
+ * @dev: device pointer for the host
+ *
+ * This function does all the usual steps needed to suspend an
+ * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * must be disabled after calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_suspend_host(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	void __iomem *mmio = hpriv->mmio;
+	u32 ctl;
+
+	if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
+		dev_err(dev, "firmware update required for suspend/resume\n");
+		return -EIO;
+	}
+
+	/*
+	 * AHCI spec rev1.1 section 8.3.3:
+	 * Software must disable interrupts prior to requesting a
+	 * transition of the HBA to D3 state.
+	 */
+	ctl = readl(mmio + HOST_CTL);
+	ctl &= ~HOST_IRQ_EN;
+	writel(ctl, mmio + HOST_CTL);
+	readl(mmio + HOST_CTL); /* flush */
+
+	return ata_host_suspend(host, PMSG_SUSPEND);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
+
+/**
+ * ahci_platform_resume_host - Resume an ahci-platform host
+ * @dev: device pointer for the host
+ *
+ * This function does all the usual steps needed to resume an ahci-platform
+ * host, note any necessary resources (ie clks, phy, etc.)  must be
+ * initialized / enabled before calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_resume_host(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	int rc;
+
+	if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
+		rc = ahci_reset_controller(host);
+		if (rc)
+			return rc;
+
+		ahci_init_controller(host);
+	}
+
+	ata_host_resume(host);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_resume_host);
+
+/**
+ * ahci_platform_suspend - Suspend an ahci-platform device
+ * @dev: the platform device to suspend
+ *
+ * This function suspends the host associated with the device, followed by
+ * disabling all the resources of the device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_suspend(struct device *dev)
+{
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_suspend_host(dev);
+	if (rc)
+		return rc;
+
+	if (pdata && pdata->suspend) {
+		rc = pdata->suspend(dev);
+		if (rc)
+			goto resume_host;
+	}
+
+	ahci_platform_disable_resources(hpriv);
+
+	return 0;
+
+resume_host:
+	ahci_platform_resume_host(dev);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_suspend);
+
+/**
+ * ahci_platform_resume - Resume an ahci-platform device
+ * @dev: the platform device to resume
+ *
+ * This function enables all the resources of the device followed by
+ * resuming the host associated with the device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_resume(struct device *dev)
+{
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	if (pdata && pdata->resume) {
+		rc = pdata->resume(dev);
+		if (rc)
+			goto disable_resources;
+	}
+
+	rc = ahci_platform_resume_host(dev);
+	if (rc)
+		goto disable_resources;
+
+	/* We resumed so update PM runtime state */
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
+
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_resume);
+#endif
+
+MODULE_DESCRIPTION("AHCI SATA platform library");
+MODULE_AUTHOR("Anton Vorontsov <avorontsov@ru.mvista.com>");
+MODULE_LICENSE("GPL");
-- 
1.8.2.3

[PATCH v3 2/4] ata: move library code from ahci_platform.c to libahci_platform.c

[Bartlomiej Zolnierkiewicz]

Move AHCI platform library code from ahci_platform.c to
libahci_platform.c and fix dependencies for ahci_st,
ahci_imx and ahci_sunxi drivers.

Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- no changes
v2:
- updated patch description

 drivers/ata/Kconfig            |   5 +-
 drivers/ata/Makefile           |   8 +-
 drivers/ata/ahci_platform.c    | 515 ---------------------------------------
 drivers/ata/libahci_platform.c | 541 +++++++++++++++++++++++++++++++++++++++++
 4 files changed, 547 insertions(+), 522 deletions(-)
 create mode 100644 drivers/ata/libahci_platform.c

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index c4db48c..371e8890 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -99,7 +99,6 @@ config SATA_AHCI_PLATFORM
 
 config AHCI_ST
 	tristate "ST AHCI SATA support"
-	depends on SATA_AHCI_PLATFORM
 	depends on ARCH_STI
 	help
 	  This option enables support for ST AHCI SATA controller.
@@ -108,7 +107,7 @@ config AHCI_ST
 
 config AHCI_IMX
 	tristate "Freescale i.MX AHCI SATA support"
-	depends on SATA_AHCI_PLATFORM && MFD_SYSCON
+	depends on MFD_SYSCON
 	help
 	  This option enables support for the Freescale i.MX SoC's
 	  onboard AHCI SATA.
@@ -117,7 +116,7 @@ config AHCI_IMX
 
 config AHCI_SUNXI
 	tristate "Allwinner sunxi AHCI SATA support"
-	depends on ARCH_SUNXI && SATA_AHCI_PLATFORM
+	depends on ARCH_SUNXI
 	help
 	  This option enables support for the Allwinner sunxi SoC's
 	  onboard AHCI SATA.
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index e20148c..6123e64 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -4,15 +4,15 @@ obj-$(CONFIG_ATA)		+= libata.o
 # non-SFF interface
 obj-$(CONFIG_SATA_AHCI)		+= ahci.o libahci.o
 obj-$(CONFIG_SATA_ACARD_AHCI)	+= acard-ahci.o libahci.o
-obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o
+obj-$(CONFIG_SATA_AHCI_PLATFORM) += ahci_platform.o libahci.o libahci_platform.o
 obj-$(CONFIG_SATA_FSL)		+= sata_fsl.o
 obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
-obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o
-obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o
-obj-$(CONFIG_AHCI_ST)		+= ahci_st.o
+obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
 
 # SFF w/ custom DMA
 obj-$(CONFIG_PDC_ADMA)		+= pdc_adma.o
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 7bd6adf..ef67e79 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -12,28 +12,15 @@
  * any later version.
  */
 
-#include <linux/clk.h>
 #include <linux/kernel.h>
-#include <linux/gfp.h>
 #include <linux/module.h>
 #include <linux/pm.h>
-#include <linux/interrupt.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/libata.h>
 #include <linux/ahci_platform.h>
-#include <linux/phy/phy.h>
-#include <linux/pm_runtime.h>
 #include "ahci.h"
 
-static void ahci_host_stop(struct ata_host *host);
-
-struct ata_port_operations ahci_platform_ops = {
-	.inherits	= &ahci_ops,
-	.host_stop	= ahci_host_stop,
-};
-EXPORT_SYMBOL_GPL(ahci_platform_ops);
-
 static const struct ata_port_info ahci_port_info = {
 	.flags		= AHCI_FLAG_COMMON,
 	.pio_mask	= ATA_PIO4,
@@ -41,345 +28,6 @@ static const struct ata_port_info ahci_port_info = {
 	.port_ops	= &ahci_platform_ops,
 };
 
-static struct scsi_host_template ahci_platform_sht = {
-	AHCI_SHT("ahci_platform"),
-};
-
-/**
- * ahci_platform_enable_clks - Enable platform clocks
- * @hpriv: host private area to store config values
- *
- * This function enables all the clks found in hpriv->clks, starting at
- * index 0. If any clk fails to enable it disables all the clks already
- * enabled in reverse order, and then returns an error.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
-{
-	int c, rc;
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
-		rc = clk_prepare_enable(hpriv->clks[c]);
-		if (rc)
-			goto disable_unprepare_clk;
-	}
-	return 0;
-
-disable_unprepare_clk:
-	while (--c >= 0)
-		clk_disable_unprepare(hpriv->clks[c]);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
-
-/**
- * ahci_platform_disable_clks - Disable platform clocks
- * @hpriv: host private area to store config values
- *
- * This function disables all the clks found in hpriv->clks, in reverse
- * order of ahci_platform_enable_clks (starting at the end of the array).
- */
-void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
-{
-	int c;
-
-	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
-		if (hpriv->clks[c])
-			clk_disable_unprepare(hpriv->clks[c]);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
-
-/**
- * ahci_platform_enable_resources - Enable platform resources
- * @hpriv: host private area to store config values
- *
- * This function enables all ahci_platform managed resources in the
- * following order:
- * 1) Regulator
- * 2) Clocks (through ahci_platform_enable_clks)
- * 3) Phy
- *
- * If resource enabling fails at any point the previous enabled resources
- * are disabled in reverse order.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
-{
-	int rc;
-
-	if (hpriv->target_pwr) {
-		rc = regulator_enable(hpriv->target_pwr);
-		if (rc)
-			return rc;
-	}
-
-	rc = ahci_platform_enable_clks(hpriv);
-	if (rc)
-		goto disable_regulator;
-
-	if (hpriv->phy) {
-		rc = phy_init(hpriv->phy);
-		if (rc)
-			goto disable_clks;
-
-		rc = phy_power_on(hpriv->phy);
-		if (rc) {
-			phy_exit(hpriv->phy);
-			goto disable_clks;
-		}
-	}
-
-	return 0;
-
-disable_clks:
-	ahci_platform_disable_clks(hpriv);
-
-disable_regulator:
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
-
-/**
- * ahci_platform_disable_resources - Disable platform resources
- * @hpriv: host private area to store config values
- *
- * This function disables all ahci_platform managed resources in the
- * following order:
- * 1) Phy
- * 2) Clocks (through ahci_platform_disable_clks)
- * 3) Regulator
- */
-void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
-{
-	if (hpriv->phy) {
-		phy_power_off(hpriv->phy);
-		phy_exit(hpriv->phy);
-	}
-
-	ahci_platform_disable_clks(hpriv);
-
-	if (hpriv->target_pwr)
-		regulator_disable(hpriv->target_pwr);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_disable_resources);
-
-static void ahci_platform_put_resources(struct device *dev, void *res)
-{
-	struct ahci_host_priv *hpriv = res;
-	int c;
-
-	if (hpriv->got_runtime_pm) {
-		pm_runtime_put_sync(dev);
-		pm_runtime_disable(dev);
-	}
-
-	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
-		clk_put(hpriv->clks[c]);
-}
-
-/**
- * ahci_platform_get_resources - Get platform resources
- * @pdev: platform device to get resources for
- *
- * This function allocates an ahci_host_priv struct, and gets the following
- * resources, storing a reference to them inside the returned struct:
- *
- * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
- * 2) regulator for controlling the targets power (optional)
- * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
- *    or for non devicetree enabled platforms a single clock
- *	4) phy (optional)
- *
- * RETURNS:
- * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
- */
-struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
-{
-	struct device *dev = &pdev->dev;
-	struct ahci_host_priv *hpriv;
-	struct clk *clk;
-	int i, rc = -ENOMEM;
-
-	if (!devres_open_group(dev, NULL, GFP_KERNEL))
-		return ERR_PTR(-ENOMEM);
-
-	hpriv = devres_alloc(ahci_platform_put_resources, sizeof(*hpriv),
-			     GFP_KERNEL);
-	if (!hpriv)
-		goto err_out;
-
-	devres_add(dev, hpriv);
-
-	hpriv->mmio = devm_ioremap_resource(dev,
-			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
-	if (IS_ERR(hpriv->mmio)) {
-		dev_err(dev, "no mmio space\n");
-		rc = PTR_ERR(hpriv->mmio);
-		goto err_out;
-	}
-
-	hpriv->target_pwr = devm_regulator_get_optional(dev, "target");
-	if (IS_ERR(hpriv->target_pwr)) {
-		rc = PTR_ERR(hpriv->target_pwr);
-		if (rc == -EPROBE_DEFER)
-			goto err_out;
-		hpriv->target_pwr = NULL;
-	}
-
-	for (i = 0; i < AHCI_MAX_CLKS; i++) {
-		/*
-		 * For now we must use clk_get(dev, NULL) for the first clock,
-		 * because some platforms (da850, spear13xx) are not yet
-		 * converted to use devicetree for clocks.  For new platforms
-		 * this is equivalent to of_clk_get(dev->of_node, 0).
-		 */
-		if (i == 0)
-			clk = clk_get(dev, NULL);
-		else
-			clk = of_clk_get(dev->of_node, i);
-
-		if (IS_ERR(clk)) {
-			rc = PTR_ERR(clk);
-			if (rc == -EPROBE_DEFER)
-				goto err_out;
-			break;
-		}
-		hpriv->clks[i] = clk;
-	}
-
-	hpriv->phy = devm_phy_get(dev, "sata-phy");
-	if (IS_ERR(hpriv->phy)) {
-		rc = PTR_ERR(hpriv->phy);
-		switch (rc) {
-		case -ENODEV:
-		case -ENOSYS:
-			/* continue normally */
-			hpriv->phy = NULL;
-			break;
-
-		case -EPROBE_DEFER:
-			goto err_out;
-
-		default:
-			dev_err(dev, "couldn't get sata-phy\n");
-			goto err_out;
-		}
-	}
-
-	pm_runtime_enable(dev);
-	pm_runtime_get_sync(dev);
-	hpriv->got_runtime_pm = true;
-
-	devres_remove_group(dev, NULL);
-	return hpriv;
-
-err_out:
-	devres_release_group(dev, NULL);
-	return ERR_PTR(rc);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
-
-/**
- * ahci_platform_init_host - Bring up an ahci-platform host
- * @pdev: platform device pointer for the host
- * @hpriv: ahci-host private data for the host
- * @pi_template: template for the ata_port_info to use
- * @force_port_map: param passed to ahci_save_initial_config
- * @mask_port_map: param passed to ahci_save_initial_config
- *
- * This function does all the usual steps needed to bring up an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
- * must be initialized / enabled before calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_init_host(struct platform_device *pdev,
-			    struct ahci_host_priv *hpriv,
-			    const struct ata_port_info *pi_template,
-			    unsigned int force_port_map,
-			    unsigned int mask_port_map)
-{
-	struct device *dev = &pdev->dev;
-	struct ata_port_info pi = *pi_template;
-	const struct ata_port_info *ppi[] = { &pi, NULL };
-	struct ata_host *host;
-	int i, irq, n_ports, rc;
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0) {
-		dev_err(dev, "no irq\n");
-		return -EINVAL;
-	}
-
-	/* prepare host */
-	hpriv->flags |= (unsigned long)pi.private_data;
-
-	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
-
-	if (hpriv->cap & HOST_CAP_NCQ)
-		pi.flags |= ATA_FLAG_NCQ;
-
-	if (hpriv->cap & HOST_CAP_PMP)
-		pi.flags |= ATA_FLAG_PMP;
-
-	ahci_set_em_messages(hpriv, &pi);
-
-	/* CAP.NP sometimes indicate the index of the last enabled
-	 * port, at other times, that of the last possible port, so
-	 * determining the maximum port number requires looking at
-	 * both CAP.NP and port_map.
-	 */
-	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
-
-	host = ata_host_alloc_pinfo(dev, ppi, n_ports);
-	if (!host)
-		return -ENOMEM;
-
-	host->private_data = hpriv;
-
-	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
-		host->flags |= ATA_HOST_PARALLEL_SCAN;
-	else
-		dev_info(dev, "SSS flag set, parallel bus scan disabled\n");
-
-	if (pi.flags & ATA_FLAG_EM)
-		ahci_reset_em(host);
-
-	for (i = 0; i < host->n_ports; i++) {
-		struct ata_port *ap = host->ports[i];
-
-		ata_port_desc(ap, "mmio %pR",
-			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
-		ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
-
-		/* set enclosure management message type */
-		if (ap->flags & ATA_FLAG_EM)
-			ap->em_message_type = hpriv->em_msg_type;
-
-		/* disabled/not-implemented port */
-		if (!(hpriv->port_map & (1 << i)))
-			ap->ops = &ata_dummy_port_ops;
-	}
-
-	rc = ahci_reset_controller(host);
-	if (rc)
-		return rc;
-
-	ahci_init_controller(host);
-	ahci_print_info(host, "platform");
-
-	return ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
-				 &ahci_platform_sht);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_init_host);
-
 static int ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -420,169 +68,6 @@ disable_resources:
 	return rc;
 }
 
-static void ahci_host_stop(struct ata_host *host)
-{
-	struct device *dev = host->dev;
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-
-	if (pdata && pdata->exit)
-		pdata->exit(dev);
-
-	ahci_platform_disable_resources(hpriv);
-}
-
-#ifdef CONFIG_PM_SLEEP
-/**
- * ahci_platform_suspend_host - Suspend an ahci-platform host
- * @dev: device pointer for the host
- *
- * This function does all the usual steps needed to suspend an
- * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
- * must be disabled after calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_suspend_host(struct device *dev)
-{
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	void __iomem *mmio = hpriv->mmio;
-	u32 ctl;
-
-	if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
-		dev_err(dev, "firmware update required for suspend/resume\n");
-		return -EIO;
-	}
-
-	/*
-	 * AHCI spec rev1.1 section 8.3.3:
-	 * Software must disable interrupts prior to requesting a
-	 * transition of the HBA to D3 state.
-	 */
-	ctl = readl(mmio + HOST_CTL);
-	ctl &= ~HOST_IRQ_EN;
-	writel(ctl, mmio + HOST_CTL);
-	readl(mmio + HOST_CTL); /* flush */
-
-	return ata_host_suspend(host, PMSG_SUSPEND);
-}
-EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
-
-/**
- * ahci_platform_resume_host - Resume an ahci-platform host
- * @dev: device pointer for the host
- *
- * This function does all the usual steps needed to resume an ahci-platform
- * host, note any necessary resources (ie clks, phy, etc.)  must be
- * initialized / enabled before calling this.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_resume_host(struct device *dev)
-{
-	struct ata_host *host = dev_get_drvdata(dev);
-	int rc;
-
-	if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
-		rc = ahci_reset_controller(host);
-		if (rc)
-			return rc;
-
-		ahci_init_controller(host);
-	}
-
-	ata_host_resume(host);
-
-	return 0;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_resume_host);
-
-/**
- * ahci_platform_suspend - Suspend an ahci-platform device
- * @dev: the platform device to suspend
- *
- * This function suspends the host associated with the device, followed by
- * disabling all the resources of the device.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_suspend(struct device *dev)
-{
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	int rc;
-
-	rc = ahci_platform_suspend_host(dev);
-	if (rc)
-		return rc;
-
-	if (pdata && pdata->suspend) {
-		rc = pdata->suspend(dev);
-		if (rc)
-			goto resume_host;
-	}
-
-	ahci_platform_disable_resources(hpriv);
-
-	return 0;
-
-resume_host:
-	ahci_platform_resume_host(dev);
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_suspend);
-
-/**
- * ahci_platform_resume - Resume an ahci-platform device
- * @dev: the platform device to resume
- *
- * This function enables all the resources of the device followed by
- * resuming the host associated with the device.
- *
- * RETURNS:
- * 0 on success otherwise a negative error code
- */
-int ahci_platform_resume(struct device *dev)
-{
-	struct ahci_platform_data *pdata = dev_get_platdata(dev);
-	struct ata_host *host = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = host->private_data;
-	int rc;
-
-	rc = ahci_platform_enable_resources(hpriv);
-	if (rc)
-		return rc;
-
-	if (pdata && pdata->resume) {
-		rc = pdata->resume(dev);
-		if (rc)
-			goto disable_resources;
-	}
-
-	rc = ahci_platform_resume_host(dev);
-	if (rc)
-		goto disable_resources;
-
-	/* We resumed so update PM runtime state */
-	pm_runtime_disable(dev);
-	pm_runtime_set_active(dev);
-	pm_runtime_enable(dev);
-
-	return 0;
-
-disable_resources:
-	ahci_platform_disable_resources(hpriv);
-
-	return rc;
-}
-EXPORT_SYMBOL_GPL(ahci_platform_resume);
-#endif
-
 static SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_platform_suspend,
 			 ahci_platform_resume);
 
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
new file mode 100644
index 0000000..7cb3a85
--- /dev/null
+++ b/drivers/ata/libahci_platform.c
@@ -0,0 +1,541 @@
+/*
+ * AHCI SATA platform library
+ *
+ * Copyright 2004-2005  Red Hat, Inc.
+ *   Jeff Garzik <jgarzik@pobox.com>
+ * Copyright 2010  MontaVista Software, LLC.
+ *   Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/kernel.h>
+#include <linux/gfp.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/pm_runtime.h>
+#include "ahci.h"
+
+static void ahci_host_stop(struct ata_host *host);
+
+struct ata_port_operations ahci_platform_ops = {
+	.inherits	= &ahci_ops,
+	.host_stop	= ahci_host_stop,
+};
+EXPORT_SYMBOL_GPL(ahci_platform_ops);
+
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT("ahci_platform"),
+};
+
+/**
+ * ahci_platform_enable_clks - Enable platform clocks
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all the clks found in hpriv->clks, starting at
+ * index 0. If any clk fails to enable it disables all the clks already
+ * enabled in reverse order, and then returns an error.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_clks(struct ahci_host_priv *hpriv)
+{
+	int c, rc;
+
+	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++) {
+		rc = clk_prepare_enable(hpriv->clks[c]);
+		if (rc)
+			goto disable_unprepare_clk;
+	}
+	return 0;
+
+disable_unprepare_clk:
+	while (--c >= 0)
+		clk_disable_unprepare(hpriv->clks[c]);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_clks);
+
+/**
+ * ahci_platform_disable_clks - Disable platform clocks
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all the clks found in hpriv->clks, in reverse
+ * order of ahci_platform_enable_clks (starting at the end of the array).
+ */
+void ahci_platform_disable_clks(struct ahci_host_priv *hpriv)
+{
+	int c;
+
+	for (c = AHCI_MAX_CLKS - 1; c >= 0; c--)
+		if (hpriv->clks[c])
+			clk_disable_unprepare(hpriv->clks[c]);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_clks);
+
+/**
+ * ahci_platform_enable_resources - Enable platform resources
+ * @hpriv: host private area to store config values
+ *
+ * This function enables all ahci_platform managed resources in the
+ * following order:
+ * 1) Regulator
+ * 2) Clocks (through ahci_platform_enable_clks)
+ * 3) Phy
+ *
+ * If resource enabling fails at any point the previous enabled resources
+ * are disabled in reverse order.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_enable_resources(struct ahci_host_priv *hpriv)
+{
+	int rc;
+
+	if (hpriv->target_pwr) {
+		rc = regulator_enable(hpriv->target_pwr);
+		if (rc)
+			return rc;
+	}
+
+	rc = ahci_platform_enable_clks(hpriv);
+	if (rc)
+		goto disable_regulator;
+
+	if (hpriv->phy) {
+		rc = phy_init(hpriv->phy);
+		if (rc)
+			goto disable_clks;
+
+		rc = phy_power_on(hpriv->phy);
+		if (rc) {
+			phy_exit(hpriv->phy);
+			goto disable_clks;
+		}
+	}
+
+	return 0;
+
+disable_clks:
+	ahci_platform_disable_clks(hpriv);
+
+disable_regulator:
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_enable_resources);
+
+/**
+ * ahci_platform_disable_resources - Disable platform resources
+ * @hpriv: host private area to store config values
+ *
+ * This function disables all ahci_platform managed resources in the
+ * following order:
+ * 1) Phy
+ * 2) Clocks (through ahci_platform_disable_clks)
+ * 3) Regulator
+ */
+void ahci_platform_disable_resources(struct ahci_host_priv *hpriv)
+{
+	if (hpriv->phy) {
+		phy_power_off(hpriv->phy);
+		phy_exit(hpriv->phy);
+	}
+
+	ahci_platform_disable_clks(hpriv);
+
+	if (hpriv->target_pwr)
+		regulator_disable(hpriv->target_pwr);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_disable_resources);
+
+static void ahci_platform_put_resources(struct device *dev, void *res)
+{
+	struct ahci_host_priv *hpriv = res;
+	int c;
+
+	if (hpriv->got_runtime_pm) {
+		pm_runtime_put_sync(dev);
+		pm_runtime_disable(dev);
+	}
+
+	for (c = 0; c < AHCI_MAX_CLKS && hpriv->clks[c]; c++)
+		clk_put(hpriv->clks[c]);
+}
+
+/**
+ * ahci_platform_get_resources - Get platform resources
+ * @pdev: platform device to get resources for
+ *
+ * This function allocates an ahci_host_priv struct, and gets the following
+ * resources, storing a reference to them inside the returned struct:
+ *
+ * 1) mmio registers (IORESOURCE_MEM 0, mandatory)
+ * 2) regulator for controlling the targets power (optional)
+ * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
+ *    or for non devicetree enabled platforms a single clock
+ *	4) phy (optional)
+ *
+ * RETURNS:
+ * The allocated ahci_host_priv on success, otherwise an ERR_PTR value
+ */
+struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct clk *clk;
+	int i, rc = -ENOMEM;
+
+	if (!devres_open_group(dev, NULL, GFP_KERNEL))
+		return ERR_PTR(-ENOMEM);
+
+	hpriv = devres_alloc(ahci_platform_put_resources, sizeof(*hpriv),
+			     GFP_KERNEL);
+	if (!hpriv)
+		goto err_out;
+
+	devres_add(dev, hpriv);
+
+	hpriv->mmio = devm_ioremap_resource(dev,
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+	if (IS_ERR(hpriv->mmio)) {
+		dev_err(dev, "no mmio space\n");
+		rc = PTR_ERR(hpriv->mmio);
+		goto err_out;
+	}
+
+	hpriv->target_pwr = devm_regulator_get_optional(dev, "target");
+	if (IS_ERR(hpriv->target_pwr)) {
+		rc = PTR_ERR(hpriv->target_pwr);
+		if (rc == -EPROBE_DEFER)
+			goto err_out;
+		hpriv->target_pwr = NULL;
+	}
+
+	for (i = 0; i < AHCI_MAX_CLKS; i++) {
+		/*
+		 * For now we must use clk_get(dev, NULL) for the first clock,
+		 * because some platforms (da850, spear13xx) are not yet
+		 * converted to use devicetree for clocks.  For new platforms
+		 * this is equivalent to of_clk_get(dev->of_node, 0).
+		 */
+		if (i == 0)
+			clk = clk_get(dev, NULL);
+		else
+			clk = of_clk_get(dev->of_node, i);
+
+		if (IS_ERR(clk)) {
+			rc = PTR_ERR(clk);
+			if (rc == -EPROBE_DEFER)
+				goto err_out;
+			break;
+		}
+		hpriv->clks[i] = clk;
+	}
+
+	hpriv->phy = devm_phy_get(dev, "sata-phy");
+	if (IS_ERR(hpriv->phy)) {
+		rc = PTR_ERR(hpriv->phy);
+		switch (rc) {
+		case -ENODEV:
+		case -ENOSYS:
+			/* continue normally */
+			hpriv->phy = NULL;
+			break;
+
+		case -EPROBE_DEFER:
+			goto err_out;
+
+		default:
+			dev_err(dev, "couldn't get sata-phy\n");
+			goto err_out;
+		}
+	}
+
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+	hpriv->got_runtime_pm = true;
+
+	devres_remove_group(dev, NULL);
+	return hpriv;
+
+err_out:
+	devres_release_group(dev, NULL);
+	return ERR_PTR(rc);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_get_resources);
+
+/**
+ * ahci_platform_init_host - Bring up an ahci-platform host
+ * @pdev: platform device pointer for the host
+ * @hpriv: ahci-host private data for the host
+ * @pi_template: template for the ata_port_info to use
+ * @force_port_map: param passed to ahci_save_initial_config
+ * @mask_port_map: param passed to ahci_save_initial_config
+ *
+ * This function does all the usual steps needed to bring up an
+ * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * must be initialized / enabled before calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_init_host(struct platform_device *pdev,
+			    struct ahci_host_priv *hpriv,
+			    const struct ata_port_info *pi_template,
+			    unsigned int force_port_map,
+			    unsigned int mask_port_map)
+{
+	struct device *dev = &pdev->dev;
+	struct ata_port_info pi = *pi_template;
+	const struct ata_port_info *ppi[] = { &pi, NULL };
+	struct ata_host *host;
+	int i, irq, n_ports, rc;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		dev_err(dev, "no irq\n");
+		return -EINVAL;
+	}
+
+	/* prepare host */
+	hpriv->flags |= (unsigned long)pi.private_data;
+
+	ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map);
+
+	if (hpriv->cap & HOST_CAP_NCQ)
+		pi.flags |= ATA_FLAG_NCQ;
+
+	if (hpriv->cap & HOST_CAP_PMP)
+		pi.flags |= ATA_FLAG_PMP;
+
+	ahci_set_em_messages(hpriv, &pi);
+
+	/* CAP.NP sometimes indicate the index of the last enabled
+	 * port, at other times, that of the last possible port, so
+	 * determining the maximum port number requires looking at
+	 * both CAP.NP and port_map.
+	 */
+	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+	host = ata_host_alloc_pinfo(dev, ppi, n_ports);
+	if (!host)
+		return -ENOMEM;
+
+	host->private_data = hpriv;
+
+	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
+		host->flags |= ATA_HOST_PARALLEL_SCAN;
+	else
+		dev_info(dev, "SSS flag set, parallel bus scan disabled\n");
+
+	if (pi.flags & ATA_FLAG_EM)
+		ahci_reset_em(host);
+
+	for (i = 0; i < host->n_ports; i++) {
+		struct ata_port *ap = host->ports[i];
+
+		ata_port_desc(ap, "mmio %pR",
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+		ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
+
+		/* set enclosure management message type */
+		if (ap->flags & ATA_FLAG_EM)
+			ap->em_message_type = hpriv->em_msg_type;
+
+		/* disabled/not-implemented port */
+		if (!(hpriv->port_map & (1 << i)))
+			ap->ops = &ata_dummy_port_ops;
+	}
+
+	rc = ahci_reset_controller(host);
+	if (rc)
+		return rc;
+
+	ahci_init_controller(host);
+	ahci_print_info(host, "platform");
+
+	return ata_host_activate(host, irq, ahci_interrupt, IRQF_SHARED,
+				 &ahci_platform_sht);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_init_host);
+
+static void ahci_host_stop(struct ata_host *host)
+{
+	struct device *dev = host->dev;
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+
+	if (pdata && pdata->exit)
+		pdata->exit(dev);
+
+	ahci_platform_disable_resources(hpriv);
+}
+
+#ifdef CONFIG_PM_SLEEP
+/**
+ * ahci_platform_suspend_host - Suspend an ahci-platform host
+ * @dev: device pointer for the host
+ *
+ * This function does all the usual steps needed to suspend an
+ * ahci-platform host, note any necessary resources (ie clks, phy, etc.)
+ * must be disabled after calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_suspend_host(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	void __iomem *mmio = hpriv->mmio;
+	u32 ctl;
+
+	if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
+		dev_err(dev, "firmware update required for suspend/resume\n");
+		return -EIO;
+	}
+
+	/*
+	 * AHCI spec rev1.1 section 8.3.3:
+	 * Software must disable interrupts prior to requesting a
+	 * transition of the HBA to D3 state.
+	 */
+	ctl = readl(mmio + HOST_CTL);
+	ctl &= ~HOST_IRQ_EN;
+	writel(ctl, mmio + HOST_CTL);
+	readl(mmio + HOST_CTL); /* flush */
+
+	return ata_host_suspend(host, PMSG_SUSPEND);
+}
+EXPORT_SYMBOL_GPL(ahci_platform_suspend_host);
+
+/**
+ * ahci_platform_resume_host - Resume an ahci-platform host
+ * @dev: device pointer for the host
+ *
+ * This function does all the usual steps needed to resume an ahci-platform
+ * host, note any necessary resources (ie clks, phy, etc.)  must be
+ * initialized / enabled before calling this.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_resume_host(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	int rc;
+
+	if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
+		rc = ahci_reset_controller(host);
+		if (rc)
+			return rc;
+
+		ahci_init_controller(host);
+	}
+
+	ata_host_resume(host);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_resume_host);
+
+/**
+ * ahci_platform_suspend - Suspend an ahci-platform device
+ * @dev: the platform device to suspend
+ *
+ * This function suspends the host associated with the device, followed by
+ * disabling all the resources of the device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_suspend(struct device *dev)
+{
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_suspend_host(dev);
+	if (rc)
+		return rc;
+
+	if (pdata && pdata->suspend) {
+		rc = pdata->suspend(dev);
+		if (rc)
+			goto resume_host;
+	}
+
+	ahci_platform_disable_resources(hpriv);
+
+	return 0;
+
+resume_host:
+	ahci_platform_resume_host(dev);
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_suspend);
+
+/**
+ * ahci_platform_resume - Resume an ahci-platform device
+ * @dev: the platform device to resume
+ *
+ * This function enables all the resources of the device followed by
+ * resuming the host associated with the device.
+ *
+ * RETURNS:
+ * 0 on success otherwise a negative error code
+ */
+int ahci_platform_resume(struct device *dev)
+{
+	struct ahci_platform_data *pdata = dev_get_platdata(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	if (pdata && pdata->resume) {
+		rc = pdata->resume(dev);
+		if (rc)
+			goto disable_resources;
+	}
+
+	rc = ahci_platform_resume_host(dev);
+	if (rc)
+		goto disable_resources;
+
+	/* We resumed so update PM runtime state */
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
+
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ahci_platform_resume);
+#endif
+
+MODULE_DESCRIPTION("AHCI SATA platform library");
+MODULE_AUTHOR("Anton Vorontsov <avorontsov@ru.mvista.com>");
+MODULE_LICENSE("GPL");
-- 
1.8.2.3

[PATCH v3 3/4] ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller

[Bartlomiej Zolnierkiewicz]

Add the new ahci_da850 host driver.

Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.

Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.

Cc: Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>
Cc: Kevin Hilman <khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org>
Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
v3:
- merged changes from Sekhar
- splitted out platform changes into separate patch
v2:
- dropped the experimental tag from the config option help
- fixed SYSCFG1 memory resource handling
- hardcoded the multiplier data and added a note about it
- used readl()/writel() instead of __raw_readl()/__raw_writel()
- dropped the superflous clock control
- cleaned up da850_sata_init()
- changed the platform device name and removed the platform ids table
- removed the deprecated ahci_platform_data platform code
- updated the patch description

 drivers/ata/Kconfig      |   9 ++++
 drivers/ata/Makefile     |   1 +
 drivers/ata/ahci_da850.c | 114 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 124 insertions(+)
 create mode 100644 drivers/ata/ahci_da850.c

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 371e8890..4b71e73 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM
 
 	  If unsure, say N.
 
+config AHCI_DA850
+	tristate "DaVinci DA850 AHCI SATA support"
+	depends on ARCH_DAVINCI_DA850
+	help
+	  This option enables support for the DaVinci DA850 SoC's
+	  onboard AHCI SATA.
+
+	  If unsure, say N.
+
 config AHCI_ST
 	tristate "ST AHCI SATA support"
 	depends on ARCH_STI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 6123e64..0646d83 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
+obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
diff --git a/drivers/ata/ahci_da850.c b/drivers/ata/ahci_da850.c
new file mode 100644
index 0000000..2c83613
--- /dev/null
+++ b/drivers/ata/ahci_da850.c
@@ -0,0 +1,114 @@
+/*
+ * DaVinci DA850 AHCI SATA platform driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include "ahci.h"
+
+/* SATA PHY Control Register offset from AHCI base */
+#define SATA_P0PHYCR_REG	0x178
+
+#define SATA_PHY_MPY(x)		((x) << 0)
+#define SATA_PHY_LOS(x)		((x) << 6)
+#define SATA_PHY_RXCDR(x)	((x) << 10)
+#define SATA_PHY_RXEQ(x)	((x) << 13)
+#define SATA_PHY_TXSWING(x)	((x) << 19)
+#define SATA_PHY_ENPLL(x)	((x) << 31)
+
+/*
+ * The multiplier needed for 1.5GHz PLL output.
+ *
+ * NOTE: This is currently hardcoded to be suitable for 100MHz crystal
+ * frequency (which is used by DA850 EVM board) and may need to be changed
+ * if you would like to use this driver on some other board.
+ */
+#define DA850_SATA_CLK_MULTIPLIER	7
+
+static void da850_sata_init(struct device *dev, void __iomem *pwrdn_reg,
+			    void __iomem *ahci_base)
+{
+	unsigned int val;
+
+	/* Enable SATA clock receiver */
+	val = readl(pwrdn_reg);
+	val &= ~BIT(0);
+	writel(val, pwrdn_reg);
+
+	val = SATA_PHY_MPY(DA850_SATA_CLK_MULTIPLIER + 1) | SATA_PHY_LOS(1) |
+	      SATA_PHY_RXCDR(4) | SATA_PHY_RXEQ(1) | SATA_PHY_TXSWING(3) |
+	      SATA_PHY_ENPLL(1);
+
+	writel(val, ahci_base + SATA_P0PHYCR_REG);
+}
+
+static const struct ata_port_info ahci_da850_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_platform_ops,
+};
+
+static int ahci_da850_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct resource *res;
+	void __iomem *pwrdn_reg;
+	int rc;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (!res)
+		goto disable_resources;
+
+	pwrdn_reg = devm_ioremap(dev, res->start, resource_size(res));
+	if (!pwrdn_reg)
+		goto disable_resources;
+
+	da850_sata_init(dev, pwrdn_reg, hpriv->mmio);
+
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info, 0, 0);
+	if (rc)
+		goto disable_resources;
+
+	return 0;
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+	return rc;
+}
+
+static SIMPLE_DEV_PM_OPS(ahci_da850_pm_ops, ahci_platform_suspend,
+			 ahci_platform_resume);
+
+static struct platform_driver ahci_da850_driver = {
+	.probe = ahci_da850_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = "ahci_da850",
+		.owner = THIS_MODULE,
+		.pm = &ahci_da850_pm_ops,
+	},
+};
+module_platform_driver(ahci_da850_driver);
+
+MODULE_DESCRIPTION("DaVinci DA850 AHCI SATA platform driver");
+MODULE_AUTHOR("Bartlomiej Zolnierkiewicz <b.zolnierkie-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>");
+MODULE_LICENSE("GPL");
-- 
1.8.2.3

[PATCH v3 3/4] ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller

[Bartlomiej Zolnierkiewicz]

Add the new ahci_da850 host driver.

Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.

Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- merged changes from Sekhar
- splitted out platform changes into separate patch
v2:
- dropped the experimental tag from the config option help
- fixed SYSCFG1 memory resource handling
- hardcoded the multiplier data and added a note about it
- used readl()/writel() instead of __raw_readl()/__raw_writel()
- dropped the superflous clock control
- cleaned up da850_sata_init()
- changed the platform device name and removed the platform ids table
- removed the deprecated ahci_platform_data platform code
- updated the patch description

 drivers/ata/Kconfig      |   9 ++++
 drivers/ata/Makefile     |   1 +
 drivers/ata/ahci_da850.c | 114 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 124 insertions(+)
 create mode 100644 drivers/ata/ahci_da850.c

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 371e8890..4b71e73 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM
 
 	  If unsure, say N.
 
+config AHCI_DA850
+	tristate "DaVinci DA850 AHCI SATA support"
+	depends on ARCH_DAVINCI_DA850
+	help
+	  This option enables support for the DaVinci DA850 SoC's
+	  onboard AHCI SATA.
+
+	  If unsure, say N.
+
 config AHCI_ST
 	tristate "ST AHCI SATA support"
 	depends on ARCH_STI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 6123e64..0646d83 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
+obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
diff --git a/drivers/ata/ahci_da850.c b/drivers/ata/ahci_da850.c
new file mode 100644
index 0000000..2c83613
--- /dev/null
+++ b/drivers/ata/ahci_da850.c
@@ -0,0 +1,114 @@
+/*
+ * DaVinci DA850 AHCI SATA platform driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include "ahci.h"
+
+/* SATA PHY Control Register offset from AHCI base */
+#define SATA_P0PHYCR_REG	0x178
+
+#define SATA_PHY_MPY(x)		((x) << 0)
+#define SATA_PHY_LOS(x)		((x) << 6)
+#define SATA_PHY_RXCDR(x)	((x) << 10)
+#define SATA_PHY_RXEQ(x)	((x) << 13)
+#define SATA_PHY_TXSWING(x)	((x) << 19)
+#define SATA_PHY_ENPLL(x)	((x) << 31)
+
+/*
+ * The multiplier needed for 1.5GHz PLL output.
+ *
+ * NOTE: This is currently hardcoded to be suitable for 100MHz crystal
+ * frequency (which is used by DA850 EVM board) and may need to be changed
+ * if you would like to use this driver on some other board.
+ */
+#define DA850_SATA_CLK_MULTIPLIER	7
+
+static void da850_sata_init(struct device *dev, void __iomem *pwrdn_reg,
+			    void __iomem *ahci_base)
+{
+	unsigned int val;
+
+	/* Enable SATA clock receiver */
+	val = readl(pwrdn_reg);
+	val &= ~BIT(0);
+	writel(val, pwrdn_reg);
+
+	val = SATA_PHY_MPY(DA850_SATA_CLK_MULTIPLIER + 1) | SATA_PHY_LOS(1) |
+	      SATA_PHY_RXCDR(4) | SATA_PHY_RXEQ(1) | SATA_PHY_TXSWING(3) |
+	      SATA_PHY_ENPLL(1);
+
+	writel(val, ahci_base + SATA_P0PHYCR_REG);
+}
+
+static const struct ata_port_info ahci_da850_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_platform_ops,
+};
+
+static int ahci_da850_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct resource *res;
+	void __iomem *pwrdn_reg;
+	int rc;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (!res)
+		goto disable_resources;
+
+	pwrdn_reg = devm_ioremap(dev, res->start, resource_size(res));
+	if (!pwrdn_reg)
+		goto disable_resources;
+
+	da850_sata_init(dev, pwrdn_reg, hpriv->mmio);
+
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info, 0, 0);
+	if (rc)
+		goto disable_resources;
+
+	return 0;
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+	return rc;
+}
+
+static SIMPLE_DEV_PM_OPS(ahci_da850_pm_ops, ahci_platform_suspend,
+			 ahci_platform_resume);
+
+static struct platform_driver ahci_da850_driver = {
+	.probe = ahci_da850_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = "ahci_da850",
+		.owner = THIS_MODULE,
+		.pm = &ahci_da850_pm_ops,
+	},
+};
+module_platform_driver(ahci_da850_driver);
+
+MODULE_DESCRIPTION("DaVinci DA850 AHCI SATA platform driver");
+MODULE_AUTHOR("Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>");
+MODULE_LICENSE("GPL");
-- 
1.8.2.3

[PATCH v3 3/4] ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller

[Bartlomiej Zolnierkiewicz]

Add the new ahci_da850 host driver.

Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.

Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- merged changes from Sekhar
- splitted out platform changes into separate patch
v2:
- dropped the experimental tag from the config option help
- fixed SYSCFG1 memory resource handling
- hardcoded the multiplier data and added a note about it
- used readl()/writel() instead of __raw_readl()/__raw_writel()
- dropped the superflous clock control
- cleaned up da850_sata_init()
- changed the platform device name and removed the platform ids table
- removed the deprecated ahci_platform_data platform code
- updated the patch description

 drivers/ata/Kconfig      |   9 ++++
 drivers/ata/Makefile     |   1 +
 drivers/ata/ahci_da850.c | 114 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 124 insertions(+)
 create mode 100644 drivers/ata/ahci_da850.c

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 371e8890..4b71e73 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM
 
 	  If unsure, say N.
 
+config AHCI_DA850
+	tristate "DaVinci DA850 AHCI SATA support"
+	depends on ARCH_DAVINCI_DA850
+	help
+	  This option enables support for the DaVinci DA850 SoC's
+	  onboard AHCI SATA.
+
+	  If unsure, say N.
+
 config AHCI_ST
 	tristate "ST AHCI SATA support"
 	depends on ARCH_STI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 6123e64..0646d83 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
+obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
diff --git a/drivers/ata/ahci_da850.c b/drivers/ata/ahci_da850.c
new file mode 100644
index 0000000..2c83613
--- /dev/null
+++ b/drivers/ata/ahci_da850.c
@@ -0,0 +1,114 @@
+/*
+ * DaVinci DA850 AHCI SATA platform driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include "ahci.h"
+
+/* SATA PHY Control Register offset from AHCI base */
+#define SATA_P0PHYCR_REG	0x178
+
+#define SATA_PHY_MPY(x)		((x) << 0)
+#define SATA_PHY_LOS(x)		((x) << 6)
+#define SATA_PHY_RXCDR(x)	((x) << 10)
+#define SATA_PHY_RXEQ(x)	((x) << 13)
+#define SATA_PHY_TXSWING(x)	((x) << 19)
+#define SATA_PHY_ENPLL(x)	((x) << 31)
+
+/*
+ * The multiplier needed for 1.5GHz PLL output.
+ *
+ * NOTE: This is currently hardcoded to be suitable for 100MHz crystal
+ * frequency (which is used by DA850 EVM board) and may need to be changed
+ * if you would like to use this driver on some other board.
+ */
+#define DA850_SATA_CLK_MULTIPLIER	7
+
+static void da850_sata_init(struct device *dev, void __iomem *pwrdn_reg,
+			    void __iomem *ahci_base)
+{
+	unsigned int val;
+
+	/* Enable SATA clock receiver */
+	val = readl(pwrdn_reg);
+	val &= ~BIT(0);
+	writel(val, pwrdn_reg);
+
+	val = SATA_PHY_MPY(DA850_SATA_CLK_MULTIPLIER + 1) | SATA_PHY_LOS(1) |
+	      SATA_PHY_RXCDR(4) | SATA_PHY_RXEQ(1) | SATA_PHY_TXSWING(3) |
+	      SATA_PHY_ENPLL(1);
+
+	writel(val, ahci_base + SATA_P0PHYCR_REG);
+}
+
+static const struct ata_port_info ahci_da850_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_platform_ops,
+};
+
+static int ahci_da850_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct resource *res;
+	void __iomem *pwrdn_reg;
+	int rc;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (!res)
+		goto disable_resources;
+
+	pwrdn_reg = devm_ioremap(dev, res->start, resource_size(res));
+	if (!pwrdn_reg)
+		goto disable_resources;
+
+	da850_sata_init(dev, pwrdn_reg, hpriv->mmio);
+
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info, 0, 0);
+	if (rc)
+		goto disable_resources;
+
+	return 0;
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+	return rc;
+}
+
+static SIMPLE_DEV_PM_OPS(ahci_da850_pm_ops, ahci_platform_suspend,
+			 ahci_platform_resume);
+
+static struct platform_driver ahci_da850_driver = {
+	.probe = ahci_da850_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = "ahci_da850",
+		.owner = THIS_MODULE,
+		.pm = &ahci_da850_pm_ops,
+	},
+};
+module_platform_driver(ahci_da850_driver);
+
+MODULE_DESCRIPTION("DaVinci DA850 AHCI SATA platform driver");
+MODULE_AUTHOR("Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>");
+MODULE_LICENSE("GPL");
-- 
1.8.2.3

[PATCH v3 4/4] ARM: davinci: da850: update SATA AHCI support

[Bartlomiej Zolnierkiewicz]

Update SATA AHCI support to make use of the new ahci_da850 host
driver (instead of the generic ahci_platform one) and remove
deprecated ahci_platform_data code.

Cc: Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>
Cc: Kevin Hilman <khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org>
Cc: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
v3:
- new patch

 arch/arm/mach-davinci/da850.c         |  2 +-
 arch/arm/mach-davinci/devices-da8xx.c | 99 +++--------------------------------
 2 files changed, 9 insertions(+), 92 deletions(-)

diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 2ab0043..85399c9 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -472,7 +472,7 @@ static struct clk_lookup da850_clks[] = {
 	CLK("spi_davinci.0",	NULL,		&spi0_clk),
 	CLK("spi_davinci.1",	NULL,		&spi1_clk),
 	CLK("vpif",		NULL,		&vpif_clk),
-	CLK("ahci",		NULL,		&sata_clk),
+	CLK("ahci_da850",		NULL,		&sata_clk),
 	CLK("davinci-rproc.0",	NULL,		&dsp_clk),
 	CLK("ehrpwm",		"fck",		&ehrpwm_clk),
 	CLK("ehrpwm",		"tbclk",	&ehrpwm_tbclk),
diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c
index 0486cdf2..56ea41d 100644
--- a/arch/arm/mach-davinci/devices-da8xx.c
+++ b/arch/arm/mach-davinci/devices-da8xx.c
@@ -1020,7 +1020,6 @@ int __init da8xx_register_spi_bus(int instance, unsigned num_chipselect)
 }
 
 #ifdef CONFIG_ARCH_DAVINCI_DA850
-
 static struct resource da850_sata_resources[] = {
 	{
 		.start	= DA850_SATA_BASE,
@@ -1028,103 +1027,22 @@ static struct resource da850_sata_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	{
+		.start	= DA8XX_SYSCFG1_BASE + DA8XX_PWRDN_REG,
+		.end	= DA8XX_SYSCFG1_BASE + DA8XX_PWRDN_REG + 0x3,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
 		.start	= IRQ_DA850_SATAINT,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
 
-/* SATA PHY Control Register offset from AHCI base */
-#define SATA_P0PHYCR_REG	0x178
-
-#define SATA_PHY_MPY(x)		((x) << 0)
-#define SATA_PHY_LOS(x)		((x) << 6)
-#define SATA_PHY_RXCDR(x)	((x) << 10)
-#define SATA_PHY_RXEQ(x)	((x) << 13)
-#define SATA_PHY_TXSWING(x)	((x) << 19)
-#define SATA_PHY_ENPLL(x)	((x) << 31)
-
-static struct clk *da850_sata_clk;
-static unsigned long da850_sata_refclkpn;
-
-/* Supported DA850 SATA crystal frequencies */
-#define KHZ_TO_HZ(freq) ((freq) * 1000)
-static unsigned long da850_sata_xtal[] = {
-	KHZ_TO_HZ(300000),
-	KHZ_TO_HZ(250000),
-	0,			/* Reserved */
-	KHZ_TO_HZ(187500),
-	KHZ_TO_HZ(150000),
-	KHZ_TO_HZ(125000),
-	KHZ_TO_HZ(120000),
-	KHZ_TO_HZ(100000),
-	KHZ_TO_HZ(75000),
-	KHZ_TO_HZ(60000),
-};
-
-static int da850_sata_init(struct device *dev, void __iomem *addr)
-{
-	int i, ret;
-	unsigned int val;
-
-	da850_sata_clk = clk_get(dev, NULL);
-	if (IS_ERR(da850_sata_clk))
-		return PTR_ERR(da850_sata_clk);
-
-	ret = clk_prepare_enable(da850_sata_clk);
-	if (ret)
-		goto err0;
-
-	/* Enable SATA clock receiver */
-	val = __raw_readl(DA8XX_SYSCFG1_VIRT(DA8XX_PWRDN_REG));
-	val &= ~BIT(0);
-	__raw_writel(val, DA8XX_SYSCFG1_VIRT(DA8XX_PWRDN_REG));
-
-	/* Get the multiplier needed for 1.5GHz PLL output */
-	for (i = 0; i < ARRAY_SIZE(da850_sata_xtal); i++)
-		if (da850_sata_xtal[i] == da850_sata_refclkpn)
-			break;
-
-	if (i == ARRAY_SIZE(da850_sata_xtal)) {
-		ret = -EINVAL;
-		goto err1;
-	}
-
-	val = SATA_PHY_MPY(i + 1) |
-		SATA_PHY_LOS(1) |
-		SATA_PHY_RXCDR(4) |
-		SATA_PHY_RXEQ(1) |
-		SATA_PHY_TXSWING(3) |
-		SATA_PHY_ENPLL(1);
-
-	__raw_writel(val, addr + SATA_P0PHYCR_REG);
-
-	return 0;
-
-err1:
-	clk_disable_unprepare(da850_sata_clk);
-err0:
-	clk_put(da850_sata_clk);
-	return ret;
-}
-
-static void da850_sata_exit(struct device *dev)
-{
-	clk_disable_unprepare(da850_sata_clk);
-	clk_put(da850_sata_clk);
-}
-
-static struct ahci_platform_data da850_sata_pdata = {
-	.init	= da850_sata_init,
-	.exit	= da850_sata_exit,
-};
-
 static u64 da850_sata_dmamask = DMA_BIT_MASK(32);
 
 static struct platform_device da850_sata_device = {
-	.name	= "ahci",
+	.name	= "ahci_da850",
 	.id	= -1,
 	.dev	= {
-		.platform_data		= &da850_sata_pdata,
 		.dma_mask		= &da850_sata_dmamask,
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
 	},
@@ -1134,9 +1052,8 @@ static struct platform_device da850_sata_device = {
 
 int __init da850_register_sata(unsigned long refclkpn)
 {
-	da850_sata_refclkpn = refclkpn;
-	if (!da850_sata_refclkpn)
-		return -EINVAL;
+	/* please see comment in drivers/ata/ahci_da850.c */
+	BUG_ON(refclkpn != 100 * 1000 * 1000);
 
 	return platform_device_register(&da850_sata_device);
 }
-- 
1.8.2.3

[PATCH v3 4/4] ARM: davinci: da850: update SATA AHCI support

[Bartlomiej Zolnierkiewicz]

Update SATA AHCI support to make use of the new ahci_da850 host
driver (instead of the generic ahci_platform one) and remove
deprecated ahci_platform_data code.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- new patch

 arch/arm/mach-davinci/da850.c         |  2 +-
 arch/arm/mach-davinci/devices-da8xx.c | 99 +++--------------------------------
 2 files changed, 9 insertions(+), 92 deletions(-)

diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 2ab0043..85399c9 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -472,7 +472,7 @@ static struct clk_lookup da850_clks[] = {
 	CLK("spi_davinci.0",	NULL,		&spi0_clk),
 	CLK("spi_davinci.1",	NULL,		&spi1_clk),
 	CLK("vpif",		NULL,		&vpif_clk),
-	CLK("ahci",		NULL,		&sata_clk),
+	CLK("ahci_da850",		NULL,		&sata_clk),
 	CLK("davinci-rproc.0",	NULL,		&dsp_clk),
 	CLK("ehrpwm",		"fck",		&ehrpwm_clk),
 	CLK("ehrpwm",		"tbclk",	&ehrpwm_tbclk),
diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c
index 0486cdf2..56ea41d 100644
--- a/arch/arm/mach-davinci/devices-da8xx.c
+++ b/arch/arm/mach-davinci/devices-da8xx.c
@@ -1020,7 +1020,6 @@ int __init da8xx_register_spi_bus(int instance, unsigned num_chipselect)
 }
 
 #ifdef CONFIG_ARCH_DAVINCI_DA850
-
 static struct resource da850_sata_resources[] = {
 	{
 		.start	= DA850_SATA_BASE,
@@ -1028,103 +1027,22 @@ static struct resource da850_sata_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	{
+		.start	= DA8XX_SYSCFG1_BASE + DA8XX_PWRDN_REG,
+		.end	= DA8XX_SYSCFG1_BASE + DA8XX_PWRDN_REG + 0x3,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
 		.start	= IRQ_DA850_SATAINT,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
 
-/* SATA PHY Control Register offset from AHCI base */
-#define SATA_P0PHYCR_REG	0x178
-
-#define SATA_PHY_MPY(x)		((x) << 0)
-#define SATA_PHY_LOS(x)		((x) << 6)
-#define SATA_PHY_RXCDR(x)	((x) << 10)
-#define SATA_PHY_RXEQ(x)	((x) << 13)
-#define SATA_PHY_TXSWING(x)	((x) << 19)
-#define SATA_PHY_ENPLL(x)	((x) << 31)
-
-static struct clk *da850_sata_clk;
-static unsigned long da850_sata_refclkpn;
-
-/* Supported DA850 SATA crystal frequencies */
-#define KHZ_TO_HZ(freq) ((freq) * 1000)
-static unsigned long da850_sata_xtal[] = {
-	KHZ_TO_HZ(300000),
-	KHZ_TO_HZ(250000),
-	0,			/* Reserved */
-	KHZ_TO_HZ(187500),
-	KHZ_TO_HZ(150000),
-	KHZ_TO_HZ(125000),
-	KHZ_TO_HZ(120000),
-	KHZ_TO_HZ(100000),
-	KHZ_TO_HZ(75000),
-	KHZ_TO_HZ(60000),
-};
-
-static int da850_sata_init(struct device *dev, void __iomem *addr)
-{
-	int i, ret;
-	unsigned int val;
-
-	da850_sata_clk = clk_get(dev, NULL);
-	if (IS_ERR(da850_sata_clk))
-		return PTR_ERR(da850_sata_clk);
-
-	ret = clk_prepare_enable(da850_sata_clk);
-	if (ret)
-		goto err0;
-
-	/* Enable SATA clock receiver */
-	val = __raw_readl(DA8XX_SYSCFG1_VIRT(DA8XX_PWRDN_REG));
-	val &= ~BIT(0);
-	__raw_writel(val, DA8XX_SYSCFG1_VIRT(DA8XX_PWRDN_REG));
-
-	/* Get the multiplier needed for 1.5GHz PLL output */
-	for (i = 0; i < ARRAY_SIZE(da850_sata_xtal); i++)
-		if (da850_sata_xtal[i] == da850_sata_refclkpn)
-			break;
-
-	if (i == ARRAY_SIZE(da850_sata_xtal)) {
-		ret = -EINVAL;
-		goto err1;
-	}
-
-	val = SATA_PHY_MPY(i + 1) |
-		SATA_PHY_LOS(1) |
-		SATA_PHY_RXCDR(4) |
-		SATA_PHY_RXEQ(1) |
-		SATA_PHY_TXSWING(3) |
-		SATA_PHY_ENPLL(1);
-
-	__raw_writel(val, addr + SATA_P0PHYCR_REG);
-
-	return 0;
-
-err1:
-	clk_disable_unprepare(da850_sata_clk);
-err0:
-	clk_put(da850_sata_clk);
-	return ret;
-}
-
-static void da850_sata_exit(struct device *dev)
-{
-	clk_disable_unprepare(da850_sata_clk);
-	clk_put(da850_sata_clk);
-}
-
-static struct ahci_platform_data da850_sata_pdata = {
-	.init	= da850_sata_init,
-	.exit	= da850_sata_exit,
-};
-
 static u64 da850_sata_dmamask = DMA_BIT_MASK(32);
 
 static struct platform_device da850_sata_device = {
-	.name	= "ahci",
+	.name	= "ahci_da850",
 	.id	= -1,
 	.dev	= {
-		.platform_data		= &da850_sata_pdata,
 		.dma_mask		= &da850_sata_dmamask,
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
 	},
@@ -1134,9 +1052,8 @@ static struct platform_device da850_sata_device = {
 
 int __init da850_register_sata(unsigned long refclkpn)
 {
-	da850_sata_refclkpn = refclkpn;
-	if (!da850_sata_refclkpn)
-		return -EINVAL;
+	/* please see comment in drivers/ata/ahci_da850.c */
+	BUG_ON(refclkpn != 100 * 1000 * 1000);
 
 	return platform_device_register(&da850_sata_device);
 }
-- 
1.8.2.3

[PATCH v3 4/4] ARM: davinci: da850: update SATA AHCI support

[Bartlomiej Zolnierkiewicz]

Update SATA AHCI support to make use of the new ahci_da850 host
driver (instead of the generic ahci_platform one) and remove
deprecated ahci_platform_data code.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
v3:
- new patch

 arch/arm/mach-davinci/da850.c         |  2 +-
 arch/arm/mach-davinci/devices-da8xx.c | 99 +++--------------------------------
 2 files changed, 9 insertions(+), 92 deletions(-)

diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 2ab0043..85399c9 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -472,7 +472,7 @@ static struct clk_lookup da850_clks[] = {
 	CLK("spi_davinci.0",	NULL,		&spi0_clk),
 	CLK("spi_davinci.1",	NULL,		&spi1_clk),
 	CLK("vpif",		NULL,		&vpif_clk),
-	CLK("ahci",		NULL,		&sata_clk),
+	CLK("ahci_da850",		NULL,		&sata_clk),
 	CLK("davinci-rproc.0",	NULL,		&dsp_clk),
 	CLK("ehrpwm",		"fck",		&ehrpwm_clk),
 	CLK("ehrpwm",		"tbclk",	&ehrpwm_tbclk),
diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c
index 0486cdf2..56ea41d 100644
--- a/arch/arm/mach-davinci/devices-da8xx.c
+++ b/arch/arm/mach-davinci/devices-da8xx.c
@@ -1020,7 +1020,6 @@ int __init da8xx_register_spi_bus(int instance, unsigned num_chipselect)
 }
 
 #ifdef CONFIG_ARCH_DAVINCI_DA850
-
 static struct resource da850_sata_resources[] = {
 	{
 		.start	= DA850_SATA_BASE,
@@ -1028,103 +1027,22 @@ static struct resource da850_sata_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	{
+		.start	= DA8XX_SYSCFG1_BASE + DA8XX_PWRDN_REG,
+		.end	= DA8XX_SYSCFG1_BASE + DA8XX_PWRDN_REG + 0x3,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
 		.start	= IRQ_DA850_SATAINT,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
 
-/* SATA PHY Control Register offset from AHCI base */
-#define SATA_P0PHYCR_REG	0x178
-
-#define SATA_PHY_MPY(x)		((x) << 0)
-#define SATA_PHY_LOS(x)		((x) << 6)
-#define SATA_PHY_RXCDR(x)	((x) << 10)
-#define SATA_PHY_RXEQ(x)	((x) << 13)
-#define SATA_PHY_TXSWING(x)	((x) << 19)
-#define SATA_PHY_ENPLL(x)	((x) << 31)
-
-static struct clk *da850_sata_clk;
-static unsigned long da850_sata_refclkpn;
-
-/* Supported DA850 SATA crystal frequencies */
-#define KHZ_TO_HZ(freq) ((freq) * 1000)
-static unsigned long da850_sata_xtal[] = {
-	KHZ_TO_HZ(300000),
-	KHZ_TO_HZ(250000),
-	0,			/* Reserved */
-	KHZ_TO_HZ(187500),
-	KHZ_TO_HZ(150000),
-	KHZ_TO_HZ(125000),
-	KHZ_TO_HZ(120000),
-	KHZ_TO_HZ(100000),
-	KHZ_TO_HZ(75000),
-	KHZ_TO_HZ(60000),
-};
-
-static int da850_sata_init(struct device *dev, void __iomem *addr)
-{
-	int i, ret;
-	unsigned int val;
-
-	da850_sata_clk = clk_get(dev, NULL);
-	if (IS_ERR(da850_sata_clk))
-		return PTR_ERR(da850_sata_clk);
-
-	ret = clk_prepare_enable(da850_sata_clk);
-	if (ret)
-		goto err0;
-
-	/* Enable SATA clock receiver */
-	val = __raw_readl(DA8XX_SYSCFG1_VIRT(DA8XX_PWRDN_REG));
-	val &= ~BIT(0);
-	__raw_writel(val, DA8XX_SYSCFG1_VIRT(DA8XX_PWRDN_REG));
-
-	/* Get the multiplier needed for 1.5GHz PLL output */
-	for (i = 0; i < ARRAY_SIZE(da850_sata_xtal); i++)
-		if (da850_sata_xtal[i] == da850_sata_refclkpn)
-			break;
-
-	if (i == ARRAY_SIZE(da850_sata_xtal)) {
-		ret = -EINVAL;
-		goto err1;
-	}
-
-	val = SATA_PHY_MPY(i + 1) |
-		SATA_PHY_LOS(1) |
-		SATA_PHY_RXCDR(4) |
-		SATA_PHY_RXEQ(1) |
-		SATA_PHY_TXSWING(3) |
-		SATA_PHY_ENPLL(1);
-
-	__raw_writel(val, addr + SATA_P0PHYCR_REG);
-
-	return 0;
-
-err1:
-	clk_disable_unprepare(da850_sata_clk);
-err0:
-	clk_put(da850_sata_clk);
-	return ret;
-}
-
-static void da850_sata_exit(struct device *dev)
-{
-	clk_disable_unprepare(da850_sata_clk);
-	clk_put(da850_sata_clk);
-}
-
-static struct ahci_platform_data da850_sata_pdata = {
-	.init	= da850_sata_init,
-	.exit	= da850_sata_exit,
-};
-
 static u64 da850_sata_dmamask = DMA_BIT_MASK(32);
 
 static struct platform_device da850_sata_device = {
-	.name	= "ahci",
+	.name	= "ahci_da850",
 	.id	= -1,
 	.dev	= {
-		.platform_data		= &da850_sata_pdata,
 		.dma_mask		= &da850_sata_dmamask,
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
 	},
@@ -1134,9 +1052,8 @@ static struct platform_device da850_sata_device = {
 
 int __init da850_register_sata(unsigned long refclkpn)
 {
-	da850_sata_refclkpn = refclkpn;
-	if (!da850_sata_refclkpn)
-		return -EINVAL;
+	/* please see comment in drivers/ata/ahci_da850.c */
+	BUG_ON(refclkpn != 100 * 1000 * 1000);
 
 	return platform_device_register(&da850_sata_device);
 }
-- 
1.8.2.3