* [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC
@ 2014-03-03 9:50 Shengzhou Liu
2014-03-03 9:50 ` [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support Shengzhou Liu
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Shengzhou Liu @ 2014-03-03 9:50 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
Add support for T2080/T2081 SoC without DPAA components.
The T2080 SoC includes the following function and features:
- Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
T2081 is a reduced personality of T2080 without SATA, sRIO, RMan,
Aurora, and with less SerDes lanes and ethernet interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/fsl/t2080si-post.dtsi | 60 +++++
arch/powerpc/boot/dts/fsl/t2081si-post.dtsi | 344 ++++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi | 96 ++++++++
arch/powerpc/include/asm/mpc85xx.h | 2 +
4 files changed, 502 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/t2080si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/t2080si-post.dtsi b/arch/powerpc/boot/dts/fsl/t2080si-post.dtsi
new file mode 100644
index 0000000..1a902fe
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t2080si-post.dtsi
@@ -0,0 +1,60 @@
+/*
+ * T2080 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t2081si-post.dtsi"
+
+&soc {
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+};
+
+&rio {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
new file mode 100644
index 0000000..0f05be2
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
@@ -0,0 +1,344 @@
+/*
+ * T2081 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+/* controller at 0x240000 */
+&pci0 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x250000 */
+&pci1 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x260000 */
+&pci2 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+/* controller at 0x270000 */
+&pci3 {
+ compatible = "fsl,t2080-pcie", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <23 2 0 0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <23 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t2080-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0
+ 94 2 0 0
+ 95 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t2080-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t2080-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t2080-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t2080-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t2080-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t2080-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-snpc@32000 {
+ compatible = "fsl,t2080-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x32000 0x1000 0x1062000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@110000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x110000 0x1000 0x111000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@118000 {
+ compatible = "fsl,dcsr-e6500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x118000 0x1000 0x119000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.7",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t2080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000
+ 0x11000 0x1000
+ 0x12000 0x1000>;
+ interrupts = <16 2 1 27
+ 16 2 1 26
+ 16 2 1 25>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x6000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+/include/ "qoriq-mpic4.3.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t2080-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t2080-clockgen", "fsl,qoriq-clockgen-2.0";
+ reg = <0xe1000 0x1000>;
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t2080-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t2080-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t2080-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+/include/ "elo3-dma-2.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t2080-esdhc", "fsl,esdhc";
+ sdhci,auto-cmd12;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.4", "fsl-usb2-mph";
+ phy_type = "utmi";
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.4", "fsl-usb2-dr";
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+/include/ "qoriq-sec5.2-0.dtsi"
+
+ L2_1: l2-cache-controller@c20000 {
+ /* Cluster 0 L2 cache */
+ compatible = "fsl,t2080-l2-cache-controller";
+ reg = <0xc20000 0x40000>;
+ next-level-cache = <&cpc>;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi
new file mode 100644
index 0000000..2628f1b
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t208xsi-pre.dtsi
@@ -0,0 +1,96 @@
+/*
+ * T2080/T2081 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e6500_power_isa.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+
+ crypto = &crypto;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ pci3 = &pci3;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ dma2 = &dma2;
+ sdhc = &sdhc;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /*
+ * Temporarily add next-level-cache info in each cpu node so
+ * that uboot can do L2 cache fixup. This can be removed once
+ * u-boot can create cpu node with cache info.
+ */
+ cpu0: PowerPC,e6500@0 {
+ device_type = "cpu";
+ reg = <0 1>;
+ next-level-cache = <&L2_1>;
+ };
+ cpu1: PowerPC,e6500@2 {
+ device_type = "cpu";
+ reg = <2 3>;
+ next-level-cache = <&L2_1>;
+ };
+ cpu2: PowerPC,e6500@4 {
+ device_type = "cpu";
+ reg = <4 5>;
+ next-level-cache = <&L2_1>;
+ };
+ cpu3: PowerPC,e6500@6 {
+ device_type = "cpu";
+ reg = <6 7>;
+ next-level-cache = <&L2_1>;
+ };
+ };
+};
diff --git a/arch/powerpc/include/asm/mpc85xx.h b/arch/powerpc/include/asm/mpc85xx.h
index 736d4ac..3bef74a 100644
--- a/arch/powerpc/include/asm/mpc85xx.h
+++ b/arch/powerpc/include/asm/mpc85xx.h
@@ -77,6 +77,8 @@
#define SVR_T1020 0x852100
#define SVR_T1021 0x852101
#define SVR_T1022 0x852102
+#define SVR_T2080 0x853000
+#define SVR_T2081 0x853100
#define SVR_8610 0x80A000
#define SVR_8641 0x809000
--
1.8.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support
2014-03-03 9:50 [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Shengzhou Liu
@ 2014-03-03 9:50 ` Shengzhou Liu
2014-04-01 21:47 ` Scott Wood
2014-03-03 9:50 ` [PATCH 3/3] powerpc/t2080rdb: Add T2080RDB " Shengzhou Liu
` (2 subsequent siblings)
3 siblings, 1 reply; 6+ messages in thread
From: Shengzhou Liu @ 2014-03-03 9:50 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
Add support for Freescale T2080/T2081 QDS Development System Board.
T2081QDS board shares the same PCB with T1040QDS with some differences.
The T2080QDS Development System is a high-performance computing,
evaluation, and development platform that supports T2080 QorIQ
Power Architecture processor, with following major features:
T2080QDS feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 memory, 4GB, Dual rank @ 1866 Mbps data rate, and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/MMC/eMMC Card
DMA:
- Three 8-channels DMA controllers
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/t2080qds.dts | 57 +++++++
arch/powerpc/boot/dts/t2081qds.dts | 48 ++++++
arch/powerpc/boot/dts/t208xqds.dtsi | 213 ++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/Kconfig | 2 +-
arch/powerpc/platforms/85xx/corenet_generic.c | 4 +
5 files changed, 323 insertions(+), 1 deletion(-)
create mode 100644 arch/powerpc/boot/dts/t2080qds.dts
create mode 100644 arch/powerpc/boot/dts/t2081qds.dts
create mode 100644 arch/powerpc/boot/dts/t208xqds.dtsi
diff --git a/arch/powerpc/boot/dts/t2080qds.dts b/arch/powerpc/boot/dts/t2080qds.dts
new file mode 100644
index 0000000..aa1d6d8
--- /dev/null
+++ b/arch/powerpc/boot/dts/t2080qds.dts
@@ -0,0 +1,57 @@
+/*
+ * T2080QDS Device Tree Source
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xqds.dtsi"
+
+/ {
+ model = "fsl,T2080QDS";
+ compatible = "fsl,T2080QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ rio: rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+};
+
+/include/ "fsl/t2080si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/t2081qds.dts b/arch/powerpc/boot/dts/t2081qds.dts
new file mode 100644
index 0000000..8ed92a0
--- /dev/null
+++ b/arch/powerpc/boot/dts/t2081qds.dts
@@ -0,0 +1,48 @@
+/*
+ * T2081QDS Device Tree Source
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xqds.dtsi"
+
+/ {
+ model = "fsl,T2081QDS";
+ compatible = "fsl,T2081QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+};
+
+/include/ "fsl/t2081si-post.dtsi"
+/include/ "fsl/qoriq-dpaa-res3.dtsi"
+/include/ "fsl/qoriq-qman-ceetm0.dtsi"
diff --git a/arch/powerpc/boot/dts/t208xqds.dtsi b/arch/powerpc/boot/dts/t208xqds.dtsi
new file mode 100644
index 0000000..54e2a1e
--- /dev/null
+++ b/arch/powerpc/boot/dts/t208xqds.dtsi
@@ -0,0 +1,213 @@
+/*
+ * T2080/T2081 QDS Device Tree Source
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+ model = "fsl,T2080QDS";
+ compatible = "fsl,T2080QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 2 0 0xf 0xff800000 0x00010000
+ 3 0 0xf 0xffdf0000 0x00008000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ boardctrl: board-control@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,fpga-qixis";
+ reg = <3 0 0x300>;
+ ranges = <0 3 0 0x300>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+ };
+
+ flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25wf040";
+ reg = <1>;
+ spi-max-frequency = <40000000>; /* input clock */
+ };
+ };
+
+ i2c@118000 {
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ eeprom@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "at24,24c02";
+ reg = <0x51>;
+ };
+
+ eeprom@57 {
+ compatible = "at24,24c02";
+ reg = <0x57>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds3232";
+ reg = <0x68>;
+ interrupts = <0x1 0x1 0 0>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ eeprom@55 {
+ compatible = "at24,24c02";
+ reg = <0x55>;
+ };
+ };
+ };
+ };
+
+ sdhc@114000 {
+ voltage-ranges = <1800 1800 3300 3300>;
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci3: pcie@ffe270000 {
+ reg = <0xf 0xfe270000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 4d46349..e3578b7 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -259,7 +259,7 @@ config CORENET_GENERIC
For 32bit kernel, the following boards are supported:
P2041 RDB, P3041 DS and P4080 DS
For 64bit kernel, the following boards are supported:
- T4240 QDS and B4 QDS
+ T208x QDS, T4240 QDS and B4 QDS
The following boards are supported for both 32bit and 64bit kernel:
P5020 DS and P5040 DS
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index fbd871e..77fd71f 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -102,6 +102,8 @@ static const char * const boards[] __initconst = {
"fsl,P4080DS",
"fsl,P5020DS",
"fsl,P5040DS",
+ "fsl,T2080QDS",
+ "fsl,T2081QDS",
"fsl,T4240QDS",
"fsl,B4860QDS",
"fsl,B4420QDS",
@@ -115,6 +117,8 @@ static const char * const hv_boards[] __initconst = {
"fsl,P4080DS-hv",
"fsl,P5020DS-hv",
"fsl,P5040DS-hv",
+ "fsl,T2080QDS-hv",
+ "fsl,T2081QDS-hv"
"fsl,T4240QDS-hv",
"fsl,B4860QDS-hv",
"fsl,B4420QDS-hv",
--
1.8.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 3/3] powerpc/t2080rdb: Add T2080RDB board support
2014-03-03 9:50 [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Shengzhou Liu
2014-03-03 9:50 ` [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support Shengzhou Liu
@ 2014-03-03 9:50 ` Shengzhou Liu
2014-03-20 0:29 ` [1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Scott Wood
2014-04-01 21:42 ` [PATCH 1/3] " Scott Wood
3 siblings, 0 replies; 6+ messages in thread
From: Shengzhou Liu @ 2014-03-03 9:50 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
The board feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP devices
- 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
- Two 10M/100M/1Gbps RGMII ports on-board
- Two 10Gbps SFP+ ports on-board
- Two 10Gbps Base-T ports on-board
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
- SerDes-1 Lane A-B: to two 10G SFP+ (MAC9 & MAC10)
- SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- SerDes-1 Lane E-H: to PCIe goldfinger (PCIe4 x4, Gen3)
- SerDes-2 Lane A-D: to PCIe slot (PCIe1 x4, Gen2)
- SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
- SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus
- NOR: 128MB 16-bit NOR flash
- NAND: 512MB 8-bit NAND flash
- CPLD: for system controlling with programable header on-board
eSPI:
- 64MB N25Q512 SPI flash
USB:
- Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
- One PCIe x4 gold-finger
- One PCIe x4 connector
- One PCIe x2 end-point device (C293 crypto co-processor)
SATA:
- Two SATA 2.0 ports on-board
SDHC:
- support a TF-card on-board
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
This board can work in two mode: standalone mode and PCIe endpoint mode.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/t2080rdb.dts | 57 +++++++
arch/powerpc/boot/dts/t208xrdb.dtsi | 210 ++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/Kconfig | 2 +-
arch/powerpc/platforms/85xx/corenet_generic.c | 4 +-
4 files changed, 271 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/t2080rdb.dts
create mode 100644 arch/powerpc/boot/dts/t208xrdb.dtsi
diff --git a/arch/powerpc/boot/dts/t2080rdb.dts b/arch/powerpc/boot/dts/t2080rdb.dts
new file mode 100644
index 0000000..e889104
--- /dev/null
+++ b/arch/powerpc/boot/dts/t2080rdb.dts
@@ -0,0 +1,57 @@
+/*
+ * T2080PCIe-RDB Board Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t208xsi-pre.dtsi"
+/include/ "t208xrdb.dtsi"
+
+/ {
+ model = "fsl,T2080RDB";
+ compatible = "fsl,T2080RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ rio: rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+};
+
+/include/ "fsl/t2080si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/t208xrdb.dtsi b/arch/powerpc/boot/dts/t208xrdb.dtsi
new file mode 100644
index 0000000..439a5c1
--- /dev/null
+++ b/arch/powerpc/boot/dts/t208xrdb.dtsi
@@ -0,0 +1,210 @@
+/*
+ * T2080/T2081PCIe-RDB Board Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+ model = "fsl,T2080RDB";
+ compatible = "fsl,T2080RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 2 0 0xf 0xff800000 0x00010000
+ 3 0 0xf 0xffdf0000 0x00008000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ boardctrl: board-control@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,t2080-cpld";
+ reg = <3 0 0x300>;
+ ranges = <0 3 0 0x300>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q512a";
+ reg = <0>;
+ spi-max-frequency = <10000000>; /* input clock */
+ };
+
+
+ flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25wf040";
+ reg = <1>;
+ spi-max-frequency = <40000000>; /* input clock */
+ };
+ };
+
+ i2c@118000 {
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ eeprom@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "at24,24c02";
+ reg = <0x51>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds3232";
+ reg = <0x68>;
+ interrupts = <0x1 0x1 0 0>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ eeprom@55 {
+ compatible = "at24,24c02";
+ reg = <0x55>;
+ };
+ };
+ };
+ };
+
+ sdhc@114000 {
+ voltage-ranges = <1800 1800 3300 3300>;
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci3: pcie@ffe270000 {
+ reg = <0xf 0xfe270000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index e3578b7..a8a0f2f 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -259,7 +259,7 @@ config CORENET_GENERIC
For 32bit kernel, the following boards are supported:
P2041 RDB, P3041 DS and P4080 DS
For 64bit kernel, the following boards are supported:
- T208x QDS, T4240 QDS and B4 QDS
+ T208x QDS/RDB, T4240 QDS and B4 QDS
The following boards are supported for both 32bit and 64bit kernel:
P5020 DS and P5040 DS
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 77fd71f..a4fdb7e 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -103,6 +103,7 @@ static const char * const boards[] __initconst = {
"fsl,P5020DS",
"fsl,P5040DS",
"fsl,T2080QDS",
+ "fsl,T2080RDB",
"fsl,T2081QDS",
"fsl,T4240QDS",
"fsl,B4860QDS",
@@ -118,7 +119,8 @@ static const char * const hv_boards[] __initconst = {
"fsl,P5020DS-hv",
"fsl,P5040DS-hv",
"fsl,T2080QDS-hv",
- "fsl,T2081QDS-hv"
+ "fsl,T2080RDB-hv",
+ "fsl,T2081QDS-hv",
"fsl,T4240QDS-hv",
"fsl,B4860QDS-hv",
"fsl,B4420QDS-hv",
--
1.8.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC
2014-03-03 9:50 [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Shengzhou Liu
2014-03-03 9:50 ` [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support Shengzhou Liu
2014-03-03 9:50 ` [PATCH 3/3] powerpc/t2080rdb: Add T2080RDB " Shengzhou Liu
@ 2014-03-20 0:29 ` Scott Wood
2014-04-01 21:42 ` [PATCH 1/3] " Scott Wood
3 siblings, 0 replies; 6+ messages in thread
From: Scott Wood @ 2014-03-20 0:29 UTC (permalink / raw)
To: Shengzhou Liu; +Cc: linuxppc-dev, prabhakar
On Mon, Mar 03, 2014 at 05:50:18PM +0800, Shengzhou Liu wrote:
> + corenet-cf@18000 {
> + compatible = "fsl,corenet-cf";
> + reg = <0x18000 0x1000>;
> + interrupts = <16 2 1 31>;
> + fsl,ccf-num-csdids = <32>;
> + fsl,ccf-num-snoopids = <32>;
> + };
As I told Prabhakar in
https://lists.ozlabs.org/pipermail/linuxppc-dev/2014-March/116093.html
this needs a binding and a new compatible property.
> + clockgen: global-utilities@e1000 {
> + compatible = "fsl,t2080-clockgen", "fsl,qoriq-clockgen-2.0";
> + reg = <0xe1000 0x1000>;
> + };
See Documentation/devicetree/bindings/clock/corenet-clock.txt
-Scott
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC
2014-03-03 9:50 [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Shengzhou Liu
` (2 preceding siblings ...)
2014-03-20 0:29 ` [1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Scott Wood
@ 2014-04-01 21:42 ` Scott Wood
3 siblings, 0 replies; 6+ messages in thread
From: Scott Wood @ 2014-04-01 21:42 UTC (permalink / raw)
To: Shengzhou Liu; +Cc: linuxppc-dev
On Mon, 2014-03-03 at 17:50 +0800, Shengzhou Liu wrote:
> + corenet-cf@18000 {
> + compatible = "fsl,corenet-cf";
> + reg = <0x18000 0x1000>;
> + interrupts = <16 2 1 31>;
> + fsl,ccf-num-csdids = <32>;
> + fsl,ccf-num-snoopids = <32>;
> + };
This is not compatible with "fsl,corenet-cf".
> + clockgen: global-utilities@e1000 {
> + compatible = "fsl,t2080-clockgen", "fsl,qoriq-clockgen-2.0";
> + reg = <0xe1000 0x1000>;
> + };
See Documentation/devicetree/bindings/clock/corenet-clock.txt
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /*
> + * Temporarily add next-level-cache info in each cpu node so
> + * that uboot can do L2 cache fixup. This can be removed once
> + * u-boot can create cpu node with cache info.
> + */
Is there a reason why this is temporary? What do we gain from U-Boot
doing the fixup? Is U-Boot doing the rest of the fixup (adding ePAPR
properties to the L2 cache nodes)?
-Scott
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support
2014-03-03 9:50 ` [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support Shengzhou Liu
@ 2014-04-01 21:47 ` Scott Wood
0 siblings, 0 replies; 6+ messages in thread
From: Scott Wood @ 2014-04-01 21:47 UTC (permalink / raw)
To: Shengzhou Liu; +Cc: linuxppc-dev
On Mon, 2014-03-03 at 17:50 +0800, Shengzhou Liu wrote:
> + dcsr: dcsr@f00000000 {
> + ranges = <0x00000000 0xf 0x00000000 0x01072000>;
> + };
This is a very odd size -- where did it come from?
-Scott
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-04-01 21:47 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-03-03 9:50 [PATCH 1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Shengzhou Liu
2014-03-03 9:50 ` [PATCH 2/3] powerpc/fsl-booke: Add initial T208x QDS board support Shengzhou Liu
2014-04-01 21:47 ` Scott Wood
2014-03-03 9:50 ` [PATCH 3/3] powerpc/t2080rdb: Add T2080RDB " Shengzhou Liu
2014-03-20 0:29 ` [1/3] powerpc/fsl-booke: Add support for T2080/T2081 SoC Scott Wood
2014-04-01 21:42 ` [PATCH 1/3] " Scott Wood
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.