* [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators
@ 2014-06-12 15:11 ` Alban Bedel
0 siblings, 0 replies; 8+ messages in thread
From: Alban Bedel @ 2014-06-12 15:11 UTC (permalink / raw)
To: Rob Herring
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
Stephen Warren, Thierry Reding, devicetree, linux-arm-kernel,
linux-tegra, linux-kernel, Alban Bedel
Currently the Tamonten DTS define a fixed regulator for the 5V supply.
However this regulator is in fact on the base board. Fix this by
properly defining the regulators found on the base boards.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
arch/arm/boot/dts/tegra20-medcom-wide.dts | 46 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/tegra20-plutux.dts | 46 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/tegra20-tamonten.dtsi | 10 +------
arch/arm/boot/dts/tegra20-tec.dts | 46 +++++++++++++++++++++++++++++++
4 files changed, 139 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
index 6d3a4cb..0cd05f7 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -64,4 +64,50 @@
<&tegra_car TEGRA20_CLK_CDEV1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
};
+
+ board_regulators {
+ compatible = "simple-bus";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_24v_reg: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vcc_24v";
+ regulator-min-microvolt = <24000000>;
+ regulator-max-microvolt = <24000000>;
+ regulator-always-on;
+ };
+
+ vdd_5v0_reg: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vdd_5v0";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vdd_3v3_reg: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "vdd_3v3";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_1v8_reg: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "vdd_1v8";
+ vin-supply = <&vdd_3v3_reg>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/tegra20-plutux.dts b/arch/arm/boot/dts/tegra20-plutux.dts
index 29051a2..a1b0e86 100644
--- a/arch/arm/boot/dts/tegra20-plutux.dts
+++ b/arch/arm/boot/dts/tegra20-plutux.dts
@@ -58,4 +58,50 @@
<&tegra_car TEGRA20_CLK_CDEV1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
};
+
+ board_regulators {
+ compatible = "simple-bus";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_24v_reg: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vcc_24v";
+ regulator-min-microvolt = <24000000>;
+ regulator-max-microvolt = <24000000>;
+ regulator-always-on;
+ };
+
+ vdd_5v0_reg: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vdd_5v0";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vdd_3v3_reg: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "vdd_3v3";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_1v8_reg: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "vdd_1v8";
+ vin-supply = <&vdd_3v3_reg>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/tegra20-tamonten.dtsi b/arch/arm/boot/dts/tegra20-tamonten.dtsi
index a1b0d96..9c83185 100644
--- a/arch/arm/boot/dts/tegra20-tamonten.dtsi
+++ b/arch/arm/boot/dts/tegra20-tamonten.dtsi
@@ -334,6 +334,7 @@
#gpio-cells = <2>;
gpio-controller;
+ /* vdd_5v0_reg must be provided by the base board */
sys-supply = <&vdd_5v0_reg>;
vin-sm0-supply = <&sys_reg>;
vin-sm1-supply = <&sys_reg>;
@@ -511,15 +512,6 @@
#address-cells = <1>;
#size-cells = <0>;
- vdd_5v0_reg: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "vdd_5v0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
pci_vdd_reg: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
diff --git a/arch/arm/boot/dts/tegra20-tec.dts b/arch/arm/boot/dts/tegra20-tec.dts
index 890562c..173201a 100644
--- a/arch/arm/boot/dts/tegra20-tec.dts
+++ b/arch/arm/boot/dts/tegra20-tec.dts
@@ -67,4 +67,50 @@
<&tegra_car TEGRA20_CLK_CDEV1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
};
+
+ board_regulators {
+ compatible = "simple-bus";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_24v_reg: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vcc_24v";
+ regulator-min-microvolt = <24000000>;
+ regulator-max-microvolt = <24000000>;
+ regulator-always-on;
+ };
+
+ vdd_5v0_reg: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vdd_5v0";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vdd_3v3_reg: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "vdd_3v3";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_1v8_reg: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "vdd_1v8";
+ vin-supply = <&vdd_3v3_reg>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
};
--
2.0.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators
@ 2014-06-12 15:11 ` Alban Bedel
0 siblings, 0 replies; 8+ messages in thread
From: Alban Bedel @ 2014-06-12 15:11 UTC (permalink / raw)
To: linux-arm-kernel
Currently the Tamonten DTS define a fixed regulator for the 5V supply.
However this regulator is in fact on the base board. Fix this by
properly defining the regulators found on the base boards.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
arch/arm/boot/dts/tegra20-medcom-wide.dts | 46 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/tegra20-plutux.dts | 46 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/tegra20-tamonten.dtsi | 10 +------
arch/arm/boot/dts/tegra20-tec.dts | 46 +++++++++++++++++++++++++++++++
4 files changed, 139 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
index 6d3a4cb..0cd05f7 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -64,4 +64,50 @@
<&tegra_car TEGRA20_CLK_CDEV1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
};
+
+ board_regulators {
+ compatible = "simple-bus";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_24v_reg: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vcc_24v";
+ regulator-min-microvolt = <24000000>;
+ regulator-max-microvolt = <24000000>;
+ regulator-always-on;
+ };
+
+ vdd_5v0_reg: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vdd_5v0";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vdd_3v3_reg: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "vdd_3v3";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_1v8_reg: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "vdd_1v8";
+ vin-supply = <&vdd_3v3_reg>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/tegra20-plutux.dts b/arch/arm/boot/dts/tegra20-plutux.dts
index 29051a2..a1b0e86 100644
--- a/arch/arm/boot/dts/tegra20-plutux.dts
+++ b/arch/arm/boot/dts/tegra20-plutux.dts
@@ -58,4 +58,50 @@
<&tegra_car TEGRA20_CLK_CDEV1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
};
+
+ board_regulators {
+ compatible = "simple-bus";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_24v_reg: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vcc_24v";
+ regulator-min-microvolt = <24000000>;
+ regulator-max-microvolt = <24000000>;
+ regulator-always-on;
+ };
+
+ vdd_5v0_reg: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vdd_5v0";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vdd_3v3_reg: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "vdd_3v3";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_1v8_reg: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "vdd_1v8";
+ vin-supply = <&vdd_3v3_reg>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/tegra20-tamonten.dtsi b/arch/arm/boot/dts/tegra20-tamonten.dtsi
index a1b0d96..9c83185 100644
--- a/arch/arm/boot/dts/tegra20-tamonten.dtsi
+++ b/arch/arm/boot/dts/tegra20-tamonten.dtsi
@@ -334,6 +334,7 @@
#gpio-cells = <2>;
gpio-controller;
+ /* vdd_5v0_reg must be provided by the base board */
sys-supply = <&vdd_5v0_reg>;
vin-sm0-supply = <&sys_reg>;
vin-sm1-supply = <&sys_reg>;
@@ -511,15 +512,6 @@
#address-cells = <1>;
#size-cells = <0>;
- vdd_5v0_reg: regulator at 0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "vdd_5v0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
pci_vdd_reg: regulator at 1 {
compatible = "regulator-fixed";
reg = <1>;
diff --git a/arch/arm/boot/dts/tegra20-tec.dts b/arch/arm/boot/dts/tegra20-tec.dts
index 890562c..173201a 100644
--- a/arch/arm/boot/dts/tegra20-tec.dts
+++ b/arch/arm/boot/dts/tegra20-tec.dts
@@ -67,4 +67,50 @@
<&tegra_car TEGRA20_CLK_CDEV1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
};
+
+ board_regulators {
+ compatible = "simple-bus";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_24v_reg: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vcc_24v";
+ regulator-min-microvolt = <24000000>;
+ regulator-max-microvolt = <24000000>;
+ regulator-always-on;
+ };
+
+ vdd_5v0_reg: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vdd_5v0";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vdd_3v3_reg: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "vdd_3v3";
+ vin-supply = <&vcc_24v_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_1v8_reg: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "vdd_1v8";
+ vin-supply = <&vdd_3v3_reg>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
};
--
2.0.0
^ permalink raw reply related [flat|nested] 8+ messages in thread[parent not found: <1402585885-28247-1-git-send-email-alban.bedel-RM9K5IK7kjKj5M59NBduVrNAH6kLmebB@public.gmane.org>]
* [PATCH 2/2] ARM: tegra: tamonten: add the display to the Medcom Wide
2014-06-12 15:11 ` Alban Bedel
(?)
@ 2014-06-12 15:11 ` Alban Bedel
-1 siblings, 0 replies; 8+ messages in thread
From: Alban Bedel @ 2014-06-12 15:11 UTC (permalink / raw)
To: Rob Herring
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
Stephen Warren, Thierry Reding,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Alban Bedel
Enable the RGB output and add the panel definition to the Medcom Wide
DTS. Also add a label to the backlight defintion to reference it in
the panel definition.
Signed-off-by: Alban Bedel <alban.bedel-RM9K5IK7kjKj5M59NBduVrNAH6kLmebB@public.gmane.org>
---
arch/arm/boot/dts/tegra20-medcom-wide.dts | 20 +++++++++++++++++++-
1 file changed, 19 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
index 0cd05f7..97a9101 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -10,6 +10,15 @@
status = "okay";
};
+ host1x@50000000 {
+ dc@54200000 {
+ rgb {
+ status = "okay";
+ nvidia,panel = <&panel>;
+ };
+ };
+ };
+
i2c@7000c000 {
wm8903: wm8903@1a {
compatible = "wlf,wm8903";
@@ -30,7 +39,7 @@
};
};
- backlight {
+ backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm 0 5000000>;
@@ -38,6 +47,15 @@
default-brightness-level = <6>;
};
+ panel: panel {
+ compatible = "innolux,n156bge-l21", "simple-panel";
+
+ power-supply = <&vdd_1v8_reg>, <&vdd_3v3_reg>;
+ enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
+
+ backlight = <&backlight>;
+ };
+
sound {
compatible = "ad,tegra-audio-wm8903-medcom-wide",
"nvidia,tegra-audio-wm8903";
--
2.0.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 2/2] ARM: tegra: tamonten: add the display to the Medcom Wide
@ 2014-06-12 15:11 ` Alban Bedel
0 siblings, 0 replies; 8+ messages in thread
From: Alban Bedel @ 2014-06-12 15:11 UTC (permalink / raw)
To: linux-arm-kernel
Enable the RGB output and add the panel definition to the Medcom Wide
DTS. Also add a label to the backlight defintion to reference it in
the panel definition.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
arch/arm/boot/dts/tegra20-medcom-wide.dts | 20 +++++++++++++++++++-
1 file changed, 19 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
index 0cd05f7..97a9101 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -10,6 +10,15 @@
status = "okay";
};
+ host1x at 50000000 {
+ dc at 54200000 {
+ rgb {
+ status = "okay";
+ nvidia,panel = <&panel>;
+ };
+ };
+ };
+
i2c at 7000c000 {
wm8903: wm8903 at 1a {
compatible = "wlf,wm8903";
@@ -30,7 +39,7 @@
};
};
- backlight {
+ backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm 0 5000000>;
@@ -38,6 +47,15 @@
default-brightness-level = <6>;
};
+ panel: panel {
+ compatible = "innolux,n156bge-l21", "simple-panel";
+
+ power-supply = <&vdd_1v8_reg>, <&vdd_3v3_reg>;
+ enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
+
+ backlight = <&backlight>;
+ };
+
sound {
compatible = "ad,tegra-audio-wm8903-medcom-wide",
"nvidia,tegra-audio-wm8903";
--
2.0.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 2/2] ARM: tegra: tamonten: add the display to the Medcom Wide
@ 2014-06-12 15:11 ` Alban Bedel
0 siblings, 0 replies; 8+ messages in thread
From: Alban Bedel @ 2014-06-12 15:11 UTC (permalink / raw)
To: Rob Herring
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
Stephen Warren, Thierry Reding, devicetree, linux-arm-kernel,
linux-tegra, linux-kernel, Alban Bedel
Enable the RGB output and add the panel definition to the Medcom Wide
DTS. Also add a label to the backlight defintion to reference it in
the panel definition.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
arch/arm/boot/dts/tegra20-medcom-wide.dts | 20 +++++++++++++++++++-
1 file changed, 19 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
index 0cd05f7..97a9101 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -10,6 +10,15 @@
status = "okay";
};
+ host1x@50000000 {
+ dc@54200000 {
+ rgb {
+ status = "okay";
+ nvidia,panel = <&panel>;
+ };
+ };
+ };
+
i2c@7000c000 {
wm8903: wm8903@1a {
compatible = "wlf,wm8903";
@@ -30,7 +39,7 @@
};
};
- backlight {
+ backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm 0 5000000>;
@@ -38,6 +47,15 @@
default-brightness-level = <6>;
};
+ panel: panel {
+ compatible = "innolux,n156bge-l21", "simple-panel";
+
+ power-supply = <&vdd_1v8_reg>, <&vdd_3v3_reg>;
+ enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
+
+ backlight = <&backlight>;
+ };
+
sound {
compatible = "ad,tegra-audio-wm8903-medcom-wide",
"nvidia,tegra-audio-wm8903";
--
2.0.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators
2014-06-12 15:11 ` Alban Bedel
(?)
@ 2014-06-12 21:17 ` Stephen Warren
-1 siblings, 0 replies; 8+ messages in thread
From: Stephen Warren @ 2014-06-12 21:17 UTC (permalink / raw)
To: Alban Bedel, Rob Herring
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
Thierry Reding, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On 06/12/2014 09:11 AM, Alban Bedel wrote:
> Currently the Tamonten DTS define a fixed regulator for the 5V supply.
> However this regulator is in fact on the base board. Fix this by
> properly defining the regulators found on the base boards.
> diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
> + board_regulators {
The name "board_regulators" encodes both type ("regulators") and
identify ("board": the regulators on the board). DT node names are
suposed to contain type but not identity information.
The way this is done in other Tegra DTs is to have a regulators node in
both the board and module DT files, and use different ranges of reg
values for the board and module; e.g. 0..99 for module and 100.. for the
board or similar.
Other than that, this patch looks fine.
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators
@ 2014-06-12 21:17 ` Stephen Warren
0 siblings, 0 replies; 8+ messages in thread
From: Stephen Warren @ 2014-06-12 21:17 UTC (permalink / raw)
To: linux-arm-kernel
On 06/12/2014 09:11 AM, Alban Bedel wrote:
> Currently the Tamonten DTS define a fixed regulator for the 5V supply.
> However this regulator is in fact on the base board. Fix this by
> properly defining the regulators found on the base boards.
> diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
> + board_regulators {
The name "board_regulators" encodes both type ("regulators") and
identify ("board": the regulators on the board). DT node names are
suposed to contain type but not identity information.
The way this is done in other Tegra DTs is to have a regulators node in
both the board and module DT files, and use different ranges of reg
values for the board and module; e.g. 0..99 for module and 100.. for the
board or similar.
Other than that, this patch looks fine.
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators
@ 2014-06-12 21:17 ` Stephen Warren
0 siblings, 0 replies; 8+ messages in thread
From: Stephen Warren @ 2014-06-12 21:17 UTC (permalink / raw)
To: Alban Bedel, Rob Herring
Cc: Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
Thierry Reding, devicetree, linux-arm-kernel, linux-tegra,
linux-kernel
On 06/12/2014 09:11 AM, Alban Bedel wrote:
> Currently the Tamonten DTS define a fixed regulator for the 5V supply.
> However this regulator is in fact on the base board. Fix this by
> properly defining the regulators found on the base boards.
> diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
> + board_regulators {
The name "board_regulators" encodes both type ("regulators") and
identify ("board": the regulators on the board). DT node names are
suposed to contain type but not identity information.
The way this is done in other Tegra DTs is to have a regulators node in
both the board and module DT files, and use different ranges of reg
values for the board and module; e.g. 0..99 for module and 100.. for the
board or similar.
Other than that, this patch looks fine.
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2014-06-12 21:18 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-06-12 15:11 [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators Alban Bedel
2014-06-12 15:11 ` Alban Bedel
[not found] ` <1402585885-28247-1-git-send-email-alban.bedel-RM9K5IK7kjKj5M59NBduVrNAH6kLmebB@public.gmane.org>
2014-06-12 15:11 ` [PATCH 2/2] ARM: tegra: tamonten: add the display to the Medcom Wide Alban Bedel
2014-06-12 15:11 ` Alban Bedel
2014-06-12 15:11 ` Alban Bedel
2014-06-12 21:17 ` [PATCH 1/2] ARM: tegra: tamonten: add the base board regulators Stephen Warren
2014-06-12 21:17 ` Stephen Warren
2014-06-12 21:17 ` Stephen Warren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.