* [PATCH v3 0/4] ARM: dts: exynos: Prepare Spring
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber
Hello,
Based on the preinstalled 3.8 based ChromeOS kernel and previous 3.15
based attempts by Stephan and me that broke for 3.16, I've prepared a
device tree for the HP Chromebook 11 aka Google Spring.
v3 mainly does style cleanups, aligning Snow and Spring better.
Not yet enabled are trackpad, Wifi and sound.
My rebasing branch for testing is here:
https://github.com/afaerber/linux/commits/spring-next
Regards,
Andreas
v1 -> v2:
* Dropped 3 documentation patches from series:
2 picked up,
https://patchwork.kernel.org/patch/4397271/
https://patchwork.kernel.org/patch/4397291/
1 already sent separately as v2, pending.
https://patchwork.kernel.org/patch/4424881/
* Minimized and beautified Spring device tree and to some degree Snow as well.
See individual patches.
v2 -> v3:
* Rebased: Two -cros-common cleanup patches were already applied
* Lots of small cleanups for both Snow and Spring
* Enabled I2S in Spring for symmetry
* Added lid-switch and gpio-keys pinctrls to Spring
Andreas Färber (4):
ARM: dts: Fix MMC pinctrl for exynos5250-snow
ARM: dts: Fold exynos5250-cros-common into exynos5250-snow
ARM: dts: Clean up exynos5250-snow
ARM: dts: Add exynos5250-spring device tree
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5250-cros-common.dtsi | 164 --------
arch/arm/boot/dts/exynos5250-snow.dts | 338 ++++++++++------
arch/arm/boot/dts/exynos5250-spring.dts | 539 ++++++++++++++++++++++++++
4 files changed, 770 insertions(+), 272 deletions(-)
delete mode 100644 arch/arm/boot/dts/exynos5250-cros-common.dtsi
create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts
--
1.9.3
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 0/4] ARM: dts: exynos: Prepare Spring
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-arm-kernel
Hello,
Based on the preinstalled 3.8 based ChromeOS kernel and previous 3.15
based attempts by Stephan and me that broke for 3.16, I've prepared a
device tree for the HP Chromebook 11 aka Google Spring.
v3 mainly does style cleanups, aligning Snow and Spring better.
Not yet enabled are trackpad, Wifi and sound.
My rebasing branch for testing is here:
https://github.com/afaerber/linux/commits/spring-next
Regards,
Andreas
v1 -> v2:
* Dropped 3 documentation patches from series:
2 picked up,
https://patchwork.kernel.org/patch/4397271/
https://patchwork.kernel.org/patch/4397291/
1 already sent separately as v2, pending.
https://patchwork.kernel.org/patch/4424881/
* Minimized and beautified Spring device tree and to some degree Snow as well.
See individual patches.
v2 -> v3:
* Rebased: Two -cros-common cleanup patches were already applied
* Lots of small cleanups for both Snow and Spring
* Enabled I2S in Spring for symmetry
* Added lid-switch and gpio-keys pinctrls to Spring
Andreas F?rber (4):
ARM: dts: Fix MMC pinctrl for exynos5250-snow
ARM: dts: Fold exynos5250-cros-common into exynos5250-snow
ARM: dts: Clean up exynos5250-snow
ARM: dts: Add exynos5250-spring device tree
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5250-cros-common.dtsi | 164 --------
arch/arm/boot/dts/exynos5250-snow.dts | 338 ++++++++++------
arch/arm/boot/dts/exynos5250-spring.dts | 539 ++++++++++++++++++++++++++
4 files changed, 770 insertions(+), 272 deletions(-)
delete mode 100644 arch/arm/boot/dts/exynos5250-cros-common.dtsi
create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts
--
1.9.3
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 1/4] ARM: dts: Fix MMC pinctrl for exynos5250-snow
2014-07-30 13:50 ` Andreas Färber
(?)
@ 2014-07-30 13:50 ` Andreas Färber
-1 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Jaehoon Chung, Ben Dooks, Kukjin Kim,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, open list
The pinctrl properties should be on the device directly and not on the
slot sub-node.
Reported-by: Doug Anderson <dianders@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v3: New (Doug Anderson)
Redundant with Jaehoon Chung's general slot@0 deprecation,
in case that hits the tree earlier.
arch/arm/boot/dts/exynos5250-snow.dts | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index f2b8c4116541..eb437f6afec1 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -240,10 +240,8 @@
*/
mmc@12230000 {
status = "okay";
- slot@0 {
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- };
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
};
i2c@12CD0000 {
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 1/4] ARM: dts: Fix MMC pinctrl for exynos5250-snow
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Jaehoon Chung, Ben Dooks, Kukjin Kim,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, open list
The pinctrl properties should be on the device directly and not on the
slot sub-node.
Reported-by: Doug Anderson <dianders@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v3: New (Doug Anderson)
Redundant with Jaehoon Chung's general slot@0 deprecation,
in case that hits the tree earlier.
arch/arm/boot/dts/exynos5250-snow.dts | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index f2b8c4116541..eb437f6afec1 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -240,10 +240,8 @@
*/
mmc@12230000 {
status = "okay";
- slot@0 {
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- };
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
};
i2c@12CD0000 {
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 1/4] ARM: dts: Fix MMC pinctrl for exynos5250-snow
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-arm-kernel
The pinctrl properties should be on the device directly and not on the
slot sub-node.
Reported-by: Doug Anderson <dianders@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andreas F?rber <afaerber@suse.de>
---
v3: New (Doug Anderson)
Redundant with Jaehoon Chung's general slot at 0 deprecation,
in case that hits the tree earlier.
arch/arm/boot/dts/exynos5250-snow.dts | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index f2b8c4116541..eb437f6afec1 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -240,10 +240,8 @@
*/
mmc at 12230000 {
status = "okay";
- slot at 0 {
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- };
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
};
i2c at 12CD0000 {
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 2/4] ARM: dts: Fold exynos5250-cros-common into exynos5250-snow
2014-07-30 13:50 ` Andreas Färber
(?)
@ 2014-07-30 13:50 ` Andreas Färber
-1 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Ben Dooks, Kukjin Kim, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
open list
The remaining common ChromeOS pieces are fairly minor.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v2 -> v3:
* Renamed subject to match Kukjin's style
* Rebased onto MMC pinctrl bug fix (Doug Anderson)
v2: New (Doug Anderson)
arch/arm/boot/dts/exynos5250-cros-common.dtsi | 164 --------------------------
arch/arm/boot/dts/exynos5250-snow.dts | 164 +++++++++++++++++++++++---
2 files changed, 145 insertions(+), 183 deletions(-)
delete mode 100644 arch/arm/boot/dts/exynos5250-cros-common.dtsi
diff --git a/arch/arm/boot/dts/exynos5250-cros-common.dtsi b/arch/arm/boot/dts/exynos5250-cros-common.dtsi
deleted file mode 100644
index e603e9c70142..000000000000
--- a/arch/arm/boot/dts/exynos5250-cros-common.dtsi
+++ /dev/null
@@ -1,164 +0,0 @@
-/*
- * Common device tree include for all Exynos 5250 boards based off of Daisy.
- *
- * Copyright (c) 2012 Google, Inc
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/ {
- aliases {
- };
-
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
- chosen {
- };
-
- pinctrl@11400000 {
- /*
- * Disabled pullups since external part has its own pullups and
- * double-pulling gets us out of spec in some cases.
- */
- i2c2_bus: i2c2-bus {
- samsung,pin-pud = <0>;
- };
- };
-
- i2c@12C60000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
- };
-
- i2c@12C70000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
- };
-
- i2c@12C80000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
-
- hdmiddc@50 {
- compatible = "samsung,exynos4210-hdmiddc";
- reg = <0x50>;
- };
- };
-
- i2c@12C90000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CA0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CB0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CD0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CE0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
-
- hdmiphy: hdmiphy@38 {
- compatible = "samsung,exynos4212-hdmiphy";
- reg = <0x38>;
- };
- };
-
- mmc@12200000 {
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
-
- slot@0 {
- reg = <0>;
- bus-width = <8>;
- };
- };
-
- mmc@12220000 {
- num-slots = <1>;
- supports-highspeed;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
-
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- wp-gpios = <&gpc2 1 0>;
- };
- };
-
- mmc@12230000 {
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- /* See board-specific dts files for pin setup */
-
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- };
- };
-
- spi_1: spi@12d30000 {
- status = "okay";
- samsung,spi-src-clk = <0>;
- num-cs = <1>;
- };
-
- hdmi {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd_irq>;
- phy = <&hdmiphy>;
- ddc = <&i2c_2>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power {
- label = "Power";
- gpios = <&gpx1 3 1>;
- linux,code = <116>; /* KEY_POWER */
- gpio-key,wakeup;
- };
- };
-};
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index eb437f6afec1..1c36cd72905f 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -10,7 +10,6 @@
/dts-v1/;
#include "exynos5250.dtsi"
-#include "exynos5250-cros-common.dtsi"
/ {
model = "Google Snow";
@@ -20,6 +19,13 @@
i2c104 = &i2c_104;
};
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ };
+
rtc@101E0000 {
status = "okay";
};
@@ -93,6 +99,13 @@
gpio-keys {
compatible = "gpio-keys";
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 1>;
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+
lid-switch {
label = "Lid";
gpios = <&gpx3 5 1>;
@@ -226,24 +239,6 @@
};
};
- mmc@12200000 {
- status = "okay";
- };
-
- mmc@12220000 {
- status = "okay";
- };
-
- /*
- * On Snow we've got SIP WiFi and so can keep drive strengths low to
- * reduce EMI.
- */
- mmc@12230000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- };
-
i2c@12CD0000 {
max98095: codec@11 {
compatible = "maxim,max98095";
@@ -292,6 +287,11 @@
};
hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
hdmi-en-supply = <&tps65090_fet7>;
vdd-supply = <&ldo8_reg>;
vdd_osc-supply = <&ldo10_reg>;
@@ -343,6 +343,10 @@
};
&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
max77686@09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx3>;
@@ -489,6 +493,10 @@
};
&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
trackpad {
reg = <0x67>;
compatible = "cypress,cyapa";
@@ -498,6 +506,118 @@
};
};
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+&mmc_2 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ wp-gpios = <&gpc2 1 0>;
+ };
+};
+
+/*
+ * On Snow we've got SIP WiFi and so can keep drive strengths low to
+ * reduce EMI.
+ */
+&mmc_3 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
&pinctrl_0 {
max77686_irq: max77686-irq {
samsung,pins = "gpx3-2";
@@ -507,4 +627,10 @@
};
};
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 2/4] ARM: dts: Fold exynos5250-cros-common into exynos5250-snow
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Ben Dooks, Kukjin Kim, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
open list
The remaining common ChromeOS pieces are fairly minor.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v2 -> v3:
* Renamed subject to match Kukjin's style
* Rebased onto MMC pinctrl bug fix (Doug Anderson)
v2: New (Doug Anderson)
arch/arm/boot/dts/exynos5250-cros-common.dtsi | 164 --------------------------
arch/arm/boot/dts/exynos5250-snow.dts | 164 +++++++++++++++++++++++---
2 files changed, 145 insertions(+), 183 deletions(-)
delete mode 100644 arch/arm/boot/dts/exynos5250-cros-common.dtsi
diff --git a/arch/arm/boot/dts/exynos5250-cros-common.dtsi b/arch/arm/boot/dts/exynos5250-cros-common.dtsi
deleted file mode 100644
index e603e9c70142..000000000000
--- a/arch/arm/boot/dts/exynos5250-cros-common.dtsi
+++ /dev/null
@@ -1,164 +0,0 @@
-/*
- * Common device tree include for all Exynos 5250 boards based off of Daisy.
- *
- * Copyright (c) 2012 Google, Inc
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/ {
- aliases {
- };
-
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
- chosen {
- };
-
- pinctrl@11400000 {
- /*
- * Disabled pullups since external part has its own pullups and
- * double-pulling gets us out of spec in some cases.
- */
- i2c2_bus: i2c2-bus {
- samsung,pin-pud = <0>;
- };
- };
-
- i2c@12C60000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
- };
-
- i2c@12C70000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
- };
-
- i2c@12C80000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
-
- hdmiddc@50 {
- compatible = "samsung,exynos4210-hdmiddc";
- reg = <0x50>;
- };
- };
-
- i2c@12C90000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CA0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CB0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CD0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c@12CE0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
-
- hdmiphy: hdmiphy@38 {
- compatible = "samsung,exynos4212-hdmiphy";
- reg = <0x38>;
- };
- };
-
- mmc@12200000 {
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
-
- slot@0 {
- reg = <0>;
- bus-width = <8>;
- };
- };
-
- mmc@12220000 {
- num-slots = <1>;
- supports-highspeed;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
-
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- wp-gpios = <&gpc2 1 0>;
- };
- };
-
- mmc@12230000 {
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- /* See board-specific dts files for pin setup */
-
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- };
- };
-
- spi_1: spi@12d30000 {
- status = "okay";
- samsung,spi-src-clk = <0>;
- num-cs = <1>;
- };
-
- hdmi {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd_irq>;
- phy = <&hdmiphy>;
- ddc = <&i2c_2>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power {
- label = "Power";
- gpios = <&gpx1 3 1>;
- linux,code = <116>; /* KEY_POWER */
- gpio-key,wakeup;
- };
- };
-};
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index eb437f6afec1..1c36cd72905f 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -10,7 +10,6 @@
/dts-v1/;
#include "exynos5250.dtsi"
-#include "exynos5250-cros-common.dtsi"
/ {
model = "Google Snow";
@@ -20,6 +19,13 @@
i2c104 = &i2c_104;
};
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ };
+
rtc@101E0000 {
status = "okay";
};
@@ -93,6 +99,13 @@
gpio-keys {
compatible = "gpio-keys";
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 1>;
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+
lid-switch {
label = "Lid";
gpios = <&gpx3 5 1>;
@@ -226,24 +239,6 @@
};
};
- mmc@12200000 {
- status = "okay";
- };
-
- mmc@12220000 {
- status = "okay";
- };
-
- /*
- * On Snow we've got SIP WiFi and so can keep drive strengths low to
- * reduce EMI.
- */
- mmc@12230000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- };
-
i2c@12CD0000 {
max98095: codec@11 {
compatible = "maxim,max98095";
@@ -292,6 +287,11 @@
};
hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
hdmi-en-supply = <&tps65090_fet7>;
vdd-supply = <&ldo8_reg>;
vdd_osc-supply = <&ldo10_reg>;
@@ -343,6 +343,10 @@
};
&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
max77686@09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx3>;
@@ -489,6 +493,10 @@
};
&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
trackpad {
reg = <0x67>;
compatible = "cypress,cyapa";
@@ -498,6 +506,118 @@
};
};
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+&mmc_2 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ wp-gpios = <&gpc2 1 0>;
+ };
+};
+
+/*
+ * On Snow we've got SIP WiFi and so can keep drive strengths low to
+ * reduce EMI.
+ */
+&mmc_3 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
&pinctrl_0 {
max77686_irq: max77686-irq {
samsung,pins = "gpx3-2";
@@ -507,4 +627,10 @@
};
};
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 2/4] ARM: dts: Fold exynos5250-cros-common into exynos5250-snow
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-arm-kernel
The remaining common ChromeOS pieces are fairly minor.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas F?rber <afaerber@suse.de>
---
v2 -> v3:
* Renamed subject to match Kukjin's style
* Rebased onto MMC pinctrl bug fix (Doug Anderson)
v2: New (Doug Anderson)
arch/arm/boot/dts/exynos5250-cros-common.dtsi | 164 --------------------------
arch/arm/boot/dts/exynos5250-snow.dts | 164 +++++++++++++++++++++++---
2 files changed, 145 insertions(+), 183 deletions(-)
delete mode 100644 arch/arm/boot/dts/exynos5250-cros-common.dtsi
diff --git a/arch/arm/boot/dts/exynos5250-cros-common.dtsi b/arch/arm/boot/dts/exynos5250-cros-common.dtsi
deleted file mode 100644
index e603e9c70142..000000000000
--- a/arch/arm/boot/dts/exynos5250-cros-common.dtsi
+++ /dev/null
@@ -1,164 +0,0 @@
-/*
- * Common device tree include for all Exynos 5250 boards based off of Daisy.
- *
- * Copyright (c) 2012 Google, Inc
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/ {
- aliases {
- };
-
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
- chosen {
- };
-
- pinctrl at 11400000 {
- /*
- * Disabled pullups since external part has its own pullups and
- * double-pulling gets us out of spec in some cases.
- */
- i2c2_bus: i2c2-bus {
- samsung,pin-pud = <0>;
- };
- };
-
- i2c at 12C60000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
- };
-
- i2c at 12C70000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
- };
-
- i2c at 12C80000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
-
- hdmiddc at 50 {
- compatible = "samsung,exynos4210-hdmiddc";
- reg = <0x50>;
- };
- };
-
- i2c at 12C90000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c at 12CA0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c at 12CB0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c at 12CD0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- };
-
- i2c at 12CE0000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <378000>;
-
- hdmiphy: hdmiphy at 38 {
- compatible = "samsung,exynos4212-hdmiphy";
- reg = <0x38>;
- };
- };
-
- mmc at 12200000 {
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
-
- slot at 0 {
- reg = <0>;
- bus-width = <8>;
- };
- };
-
- mmc at 12220000 {
- num-slots = <1>;
- supports-highspeed;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
-
- slot at 0 {
- reg = <0>;
- bus-width = <4>;
- wp-gpios = <&gpc2 1 0>;
- };
- };
-
- mmc at 12230000 {
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- /* See board-specific dts files for pin setup */
-
- slot at 0 {
- reg = <0>;
- bus-width = <4>;
- };
- };
-
- spi_1: spi at 12d30000 {
- status = "okay";
- samsung,spi-src-clk = <0>;
- num-cs = <1>;
- };
-
- hdmi {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd_irq>;
- phy = <&hdmiphy>;
- ddc = <&i2c_2>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power {
- label = "Power";
- gpios = <&gpx1 3 1>;
- linux,code = <116>; /* KEY_POWER */
- gpio-key,wakeup;
- };
- };
-};
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index eb437f6afec1..1c36cd72905f 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -10,7 +10,6 @@
/dts-v1/;
#include "exynos5250.dtsi"
-#include "exynos5250-cros-common.dtsi"
/ {
model = "Google Snow";
@@ -20,6 +19,13 @@
i2c104 = &i2c_104;
};
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ };
+
rtc at 101E0000 {
status = "okay";
};
@@ -93,6 +99,13 @@
gpio-keys {
compatible = "gpio-keys";
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 1>;
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+
lid-switch {
label = "Lid";
gpios = <&gpx3 5 1>;
@@ -226,24 +239,6 @@
};
};
- mmc at 12200000 {
- status = "okay";
- };
-
- mmc at 12220000 {
- status = "okay";
- };
-
- /*
- * On Snow we've got SIP WiFi and so can keep drive strengths low to
- * reduce EMI.
- */
- mmc at 12230000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
- };
-
i2c at 12CD0000 {
max98095: codec at 11 {
compatible = "maxim,max98095";
@@ -292,6 +287,11 @@
};
hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
hdmi-en-supply = <&tps65090_fet7>;
vdd-supply = <&ldo8_reg>;
vdd_osc-supply = <&ldo10_reg>;
@@ -343,6 +343,10 @@
};
&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
max77686 at 09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx3>;
@@ -489,6 +493,10 @@
};
&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
trackpad {
reg = <0x67>;
compatible = "cypress,cyapa";
@@ -498,6 +506,118 @@
};
};
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc at 50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy at 38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot at 0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+&mmc_2 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ wp-gpios = <&gpc2 1 0>;
+ };
+};
+
+/*
+ * On Snow we've got SIP WiFi and so can keep drive strengths low to
+ * reduce EMI.
+ */
+&mmc_3 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
&pinctrl_0 {
max77686_irq: max77686-irq {
samsung,pins = "gpx3-2";
@@ -507,4 +627,10 @@
};
};
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 3/4] ARM: dts: Clean up exynos5250-snow
2014-07-30 13:50 ` Andreas Färber
(?)
@ 2014-07-30 13:50 ` Andreas Färber
-1 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Ben Dooks, Kukjin Kim, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
open list
Use the new style of referencing inherited nodes and use symbolic names.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v3: New (Doug Anderson)
arch/arm/boot/dts/exynos5250-snow.dts | 182 +++++++++++++++++-----------------
1 file changed, 90 insertions(+), 92 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index 1c36cd72905f..2ed6cb04a2db 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -9,6 +9,8 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "exynos5250.dtsi"
/ {
@@ -30,85 +32,19 @@
status = "okay";
};
- pinctrl@11400000 {
- ec_irq: ec-irq {
- samsung,pins = "gpx1-6";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- sd3_clk: sd3-clk {
- samsung,pin-drv = <0>;
- };
-
- sd3_cmd: sd3-cmd {
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- sd3_bus4: sd3-bus-width4 {
- samsung,pin-drv = <0>;
- };
-
- max98095_en: max98095-en {
- samsung,pins = "gpx1-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- tps65090_irq: tps65090-irq {
- samsung,pins = "gpx2-6";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- usb3_vbus_en: usb3-vbus-en {
- samsung,pins = "gpx2-7";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- hdmi_hpd_irq: hdmi-hpd-irq {
- samsung,pins = "gpx3-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
- };
- };
-
- pinctrl@13400000 {
- arb_their_claim: arb-their-claim {
- samsung,pins = "gpe0-4";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- arb_our_claim: arb-our-claim {
- samsung,pins = "gpf0-3";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
- };
-
gpio-keys {
compatible = "gpio-keys";
power {
label = "Power";
- gpios = <&gpx1 3 1>;
- linux,code = <116>; /* KEY_POWER */
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
gpio-key,wakeup;
};
lid-switch {
label = "Lid";
- gpios = <&gpx3 5 1>;
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
linux,input-type = <5>; /* EV_SW */
linux,code = <0>; /* SW_LID */
debounce-interval = <1>;
@@ -129,8 +65,8 @@
i2c-parent = <&{/i2c@12CA0000}>;
- our-claim-gpio = <&gpf0 3 1>;
- their-claim-gpios = <&gpe0 4 1>;
+ our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
+ their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
slew-delay-us = <10>;
wait-retry-us = <3000>;
wait-free-us = <50000>;
@@ -239,19 +175,6 @@
};
};
- i2c@12CD0000 {
- max98095: codec@11 {
- compatible = "maxim,max98095";
- reg = <0x11>;
- pinctrl-0 = <&max98095_en>;
- pinctrl-names = "default";
- };
- };
-
- i2s0: i2s@03830000 {
- status = "okay";
- };
-
sound {
compatible = "google,snow-audio-max98095";
@@ -265,18 +188,14 @@
regulator-name = "P5.0V_USB3CON";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpx2 7 0>;
+ gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb3_vbus_en>;
enable-active-high;
};
- phy@12100000 {
- vbus-supply = <&usb3_vbus_reg>;
- };
-
usb@12110000 {
- samsung,vbus-gpio = <&gpx1 1 0>;
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
};
fixed-rate-clocks {
@@ -287,7 +206,7 @@
};
hdmi {
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd_irq>;
phy = <&hdmiphy>;
@@ -322,7 +241,7 @@
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx0 7 0>;
+ samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
display-timings {
native-mode = <&timing1>;
@@ -547,6 +466,13 @@
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
+
+ max98095: codec@11 {
+ compatible = "maxim,max98095";
+ reg = <0x11>;
+ pinctrl-0 = <&max98095_en>;
+ pinctrl-names = "default";
+ };
};
&i2c_8 {
@@ -560,6 +486,10 @@
};
};
+&i2s0 {
+ status = "okay";
+};
+
&mmc_0 {
status = "okay";
num-slots = <1>;
@@ -625,6 +555,70 @@
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ max98095_en: max98095-en {
+ samsung,pins = "gpx1-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ tps65090_irq: tps65090-irq {
+ samsung,pins = "gpx2-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ usb3_vbus_en: usb3-vbus-en {
+ samsung,pins = "gpx2-7";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ arb_their_claim: arb-their-claim {
+ samsung,pins = "gpe0-4";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ arb_our_claim: arb-our-claim {
+ samsung,pins = "gpf0-3";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd3_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd3_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd3_bus4 {
+ samsung,pin-drv = <0>;
};
&spi_1 {
@@ -633,4 +627,8 @@
num-cs = <1>;
};
+&usbdrd_phy {
+ vbus-supply = <&usb3_vbus_reg>;
+};
+
#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 3/4] ARM: dts: Clean up exynos5250-snow
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: Mark Rutland, devicetree, Kukjin Kim, Vincent Palatin,
Pawel Moll, Ian Campbell, open list, Kumar Gala,
Stephan van Schaik, Doug Anderson, Rob Herring, Ben Dooks,
Andreas Färber, Russell King, Javier Martinez Canillas,
linux-arm-kernel
Use the new style of referencing inherited nodes and use symbolic names.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v3: New (Doug Anderson)
arch/arm/boot/dts/exynos5250-snow.dts | 182 +++++++++++++++++-----------------
1 file changed, 90 insertions(+), 92 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index 1c36cd72905f..2ed6cb04a2db 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -9,6 +9,8 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "exynos5250.dtsi"
/ {
@@ -30,85 +32,19 @@
status = "okay";
};
- pinctrl@11400000 {
- ec_irq: ec-irq {
- samsung,pins = "gpx1-6";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- sd3_clk: sd3-clk {
- samsung,pin-drv = <0>;
- };
-
- sd3_cmd: sd3-cmd {
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- sd3_bus4: sd3-bus-width4 {
- samsung,pin-drv = <0>;
- };
-
- max98095_en: max98095-en {
- samsung,pins = "gpx1-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- tps65090_irq: tps65090-irq {
- samsung,pins = "gpx2-6";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- usb3_vbus_en: usb3-vbus-en {
- samsung,pins = "gpx2-7";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- hdmi_hpd_irq: hdmi-hpd-irq {
- samsung,pins = "gpx3-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
- };
- };
-
- pinctrl@13400000 {
- arb_their_claim: arb-their-claim {
- samsung,pins = "gpe0-4";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- arb_our_claim: arb-our-claim {
- samsung,pins = "gpf0-3";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
- };
-
gpio-keys {
compatible = "gpio-keys";
power {
label = "Power";
- gpios = <&gpx1 3 1>;
- linux,code = <116>; /* KEY_POWER */
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
gpio-key,wakeup;
};
lid-switch {
label = "Lid";
- gpios = <&gpx3 5 1>;
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
linux,input-type = <5>; /* EV_SW */
linux,code = <0>; /* SW_LID */
debounce-interval = <1>;
@@ -129,8 +65,8 @@
i2c-parent = <&{/i2c@12CA0000}>;
- our-claim-gpio = <&gpf0 3 1>;
- their-claim-gpios = <&gpe0 4 1>;
+ our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
+ their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
slew-delay-us = <10>;
wait-retry-us = <3000>;
wait-free-us = <50000>;
@@ -239,19 +175,6 @@
};
};
- i2c@12CD0000 {
- max98095: codec@11 {
- compatible = "maxim,max98095";
- reg = <0x11>;
- pinctrl-0 = <&max98095_en>;
- pinctrl-names = "default";
- };
- };
-
- i2s0: i2s@03830000 {
- status = "okay";
- };
-
sound {
compatible = "google,snow-audio-max98095";
@@ -265,18 +188,14 @@
regulator-name = "P5.0V_USB3CON";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpx2 7 0>;
+ gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb3_vbus_en>;
enable-active-high;
};
- phy@12100000 {
- vbus-supply = <&usb3_vbus_reg>;
- };
-
usb@12110000 {
- samsung,vbus-gpio = <&gpx1 1 0>;
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
};
fixed-rate-clocks {
@@ -287,7 +206,7 @@
};
hdmi {
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd_irq>;
phy = <&hdmiphy>;
@@ -322,7 +241,7 @@
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx0 7 0>;
+ samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
display-timings {
native-mode = <&timing1>;
@@ -547,6 +466,13 @@
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
+
+ max98095: codec@11 {
+ compatible = "maxim,max98095";
+ reg = <0x11>;
+ pinctrl-0 = <&max98095_en>;
+ pinctrl-names = "default";
+ };
};
&i2c_8 {
@@ -560,6 +486,10 @@
};
};
+&i2s0 {
+ status = "okay";
+};
+
&mmc_0 {
status = "okay";
num-slots = <1>;
@@ -625,6 +555,70 @@
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ max98095_en: max98095-en {
+ samsung,pins = "gpx1-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ tps65090_irq: tps65090-irq {
+ samsung,pins = "gpx2-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ usb3_vbus_en: usb3-vbus-en {
+ samsung,pins = "gpx2-7";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ arb_their_claim: arb-their-claim {
+ samsung,pins = "gpe0-4";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ arb_our_claim: arb-our-claim {
+ samsung,pins = "gpf0-3";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd3_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd3_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd3_bus4 {
+ samsung,pin-drv = <0>;
};
&spi_1 {
@@ -633,4 +627,8 @@
num-cs = <1>;
};
+&usbdrd_phy {
+ vbus-supply = <&usb3_vbus_reg>;
+};
+
#include "cros-ec-keyboard.dtsi"
--
1.9.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 3/4] ARM: dts: Clean up exynos5250-snow
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-arm-kernel
Use the new style of referencing inherited nodes and use symbolic names.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas F?rber <afaerber@suse.de>
---
v3: New (Doug Anderson)
arch/arm/boot/dts/exynos5250-snow.dts | 182 +++++++++++++++++-----------------
1 file changed, 90 insertions(+), 92 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index 1c36cd72905f..2ed6cb04a2db 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -9,6 +9,8 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "exynos5250.dtsi"
/ {
@@ -30,85 +32,19 @@
status = "okay";
};
- pinctrl at 11400000 {
- ec_irq: ec-irq {
- samsung,pins = "gpx1-6";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- sd3_clk: sd3-clk {
- samsung,pin-drv = <0>;
- };
-
- sd3_cmd: sd3-cmd {
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- sd3_bus4: sd3-bus-width4 {
- samsung,pin-drv = <0>;
- };
-
- max98095_en: max98095-en {
- samsung,pins = "gpx1-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- tps65090_irq: tps65090-irq {
- samsung,pins = "gpx2-6";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- usb3_vbus_en: usb3-vbus-en {
- samsung,pins = "gpx2-7";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- hdmi_hpd_irq: hdmi-hpd-irq {
- samsung,pins = "gpx3-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
- };
- };
-
- pinctrl at 13400000 {
- arb_their_claim: arb-their-claim {
- samsung,pins = "gpe0-4";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- arb_our_claim: arb-our-claim {
- samsung,pins = "gpf0-3";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
- };
-
gpio-keys {
compatible = "gpio-keys";
power {
label = "Power";
- gpios = <&gpx1 3 1>;
- linux,code = <116>; /* KEY_POWER */
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
gpio-key,wakeup;
};
lid-switch {
label = "Lid";
- gpios = <&gpx3 5 1>;
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
linux,input-type = <5>; /* EV_SW */
linux,code = <0>; /* SW_LID */
debounce-interval = <1>;
@@ -129,8 +65,8 @@
i2c-parent = <&{/i2c@12CA0000}>;
- our-claim-gpio = <&gpf0 3 1>;
- their-claim-gpios = <&gpe0 4 1>;
+ our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
+ their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
slew-delay-us = <10>;
wait-retry-us = <3000>;
wait-free-us = <50000>;
@@ -239,19 +175,6 @@
};
};
- i2c at 12CD0000 {
- max98095: codec at 11 {
- compatible = "maxim,max98095";
- reg = <0x11>;
- pinctrl-0 = <&max98095_en>;
- pinctrl-names = "default";
- };
- };
-
- i2s0: i2s at 03830000 {
- status = "okay";
- };
-
sound {
compatible = "google,snow-audio-max98095";
@@ -265,18 +188,14 @@
regulator-name = "P5.0V_USB3CON";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpx2 7 0>;
+ gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb3_vbus_en>;
enable-active-high;
};
- phy at 12100000 {
- vbus-supply = <&usb3_vbus_reg>;
- };
-
usb at 12110000 {
- samsung,vbus-gpio = <&gpx1 1 0>;
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
};
fixed-rate-clocks {
@@ -287,7 +206,7 @@
};
hdmi {
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd_irq>;
phy = <&hdmiphy>;
@@ -322,7 +241,7 @@
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx0 7 0>;
+ samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
display-timings {
native-mode = <&timing1>;
@@ -547,6 +466,13 @@
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
+
+ max98095: codec at 11 {
+ compatible = "maxim,max98095";
+ reg = <0x11>;
+ pinctrl-0 = <&max98095_en>;
+ pinctrl-names = "default";
+ };
};
&i2c_8 {
@@ -560,6 +486,10 @@
};
};
+&i2s0 {
+ status = "okay";
+};
+
&mmc_0 {
status = "okay";
num-slots = <1>;
@@ -625,6 +555,70 @@
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ max98095_en: max98095-en {
+ samsung,pins = "gpx1-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ tps65090_irq: tps65090-irq {
+ samsung,pins = "gpx2-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ usb3_vbus_en: usb3-vbus-en {
+ samsung,pins = "gpx2-7";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ arb_their_claim: arb-their-claim {
+ samsung,pins = "gpe0-4";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ arb_our_claim: arb-our-claim {
+ samsung,pins = "gpf0-3";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd3_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd3_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd3_bus4 {
+ samsung,pin-drv = <0>;
};
&spi_1 {
@@ -633,4 +627,8 @@
num-cs = <1>;
};
+&usbdrd_phy {
+ vbus-supply = <&usb3_vbus_reg>;
+};
+
#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
2014-07-30 13:50 ` Andreas Färber
(?)
@ 2014-07-30 13:50 ` Andreas Färber
-1 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
open list
Adds initial support for the HP Chromebook 11.
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v2 -> v3:
* Use GPIO_ACTIVE_{LOW,HIGH} (Doug Anderson)
* Use symbolic KEY_POWER instead of comment
* Moved hsic_reset to new USB3503 node's reset-gpios (Vincent Palatin)
* Use dp_hpd_gpio for dp-controller (Doug Anderson, Ajay Kumar)
* Override sd1_{clk,cmd,cd,bus4} pinctrl similar to Snow (Doug Anderson)
* Added ec_irq pinctrl for cros_ec (Doug Anderson)
* Reordered nodes to minimize diff against Snow (Doug Anderson)
* Dropped obsolete mmc_2 override (Doug Anderson)
* Added lid-switch node (Doug Anderson)
* Added gpio-keys pinctrl (Doug Anderson)
* Added bootargs to avoid empty /chosen node and to document console setting
* Renamed s5m8767_pmic node to avoid underscore
* Use new style for overriding inherited pinctrl nodes, too
* Enable i2s0 node
v1 -> v2:
* Use label-based overriding/extension of nodes. (Doug Anderson)
* Dropped tps65090 for now, until we know where to place it.
* Dropped non-Spring nodes from -cros-common.dtsi rather than disabling them.
* Enabled a missing MMC node for access to internal storage.
* Dropped display-timings from dp-controller node. (Ajay Kumar)
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5250-spring.dts | 539 ++++++++++++++++++++++++++++++++
2 files changed, 540 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 80a781f76e88..dec4c292f63d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos5250-arndale.dtb \
exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \
+ exynos5250-spring.dtb \
exynos5260-xyref5260.dtb \
exynos5410-smdk5410.dtb \
exynos5420-arndale-octa.dtb \
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
new file mode 100644
index 000000000000..bcca892bf2ff
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -0,0 +1,539 @@
+/*
+ * Google Spring board device tree source
+ *
+ * Copyright (c) 2013 Google, Inc
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "exynos5250.dtsi"
+
+/ {
+ model = "Google Spring";
+ compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ bootargs = "console=tty1";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_key_irq>, <&lid_irq>;
+
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+
+ lid-switch {
+ label = "Lid";
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0>; /* SW_LID */
+ debounce-interval = <1>;
+ gpio-key,wakeup;
+ };
+ };
+
+ usb3_vbus_reg: regulator-usb3 {
+ compatible = "regulator-fixed";
+ regulator-name = "P5.0V_USB3CON";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpe1 0 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ };
+
+ usb@12110000 {
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503a";
+ reset-gpios = <&hsic_reset>;
+ };
+
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ hdmi {
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
+ hdmi-en-supply = <&s5m_ldo8_reg>;
+ vdd-supply = <&s5m_ldo8_reg>;
+ vdd_osc-supply = <&s5m_ldo10_reg>;
+ vdd_pll-supply = <&s5m_ldo8_reg>;
+ };
+
+ fimd@14400000 {
+ status = "okay";
+ samsung,invert-vclk;
+ };
+
+ dp-controller@145B0000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hpd_gpio>;
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <1>;
+ samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ s5m8767-pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+ wakeup-source;
+
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
+ <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+ <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
+ <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+ <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+
+ /*
+ * The following arrays of DVS voltages are not used, since we are
+ * not using GPIOs to control PMIC bucks, but they must be defined
+ * to please the driver.
+ */
+ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1000000>, <1000000>,
+ <1000000>, <1000000>;
+
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ clocks {
+ compatible = "samsung,s5m8767-clk";
+ #clock-cells = <1>;
+ clock-output-names = "en32khz_ap",
+ "en32khz_cp",
+ "en32khz_bt";
+ };
+
+ regulators {
+ s5m_ldo4_reg: LDO4 {
+ regulator-name = "P1.0V_LDO_OUT4";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo5_reg: LDO5 {
+ regulator-name = "P1.0V_LDO_OUT5";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo6_reg: LDO6 {
+ regulator-name = "vdd_mydp";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo7_reg: LDO7 {
+ regulator-name = "P1.1V_LDO_OUT7";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo8_reg: LDO8 {
+ regulator-name = "P1.0V_LDO_OUT8";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo10_reg: LDO10 {
+ regulator-name = "P1.8V_LDO_OUT10";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo11_reg: LDO11 {
+ regulator-name = "P1.8V_LDO_OUT11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo12_reg: LDO12 {
+ regulator-name = "P3.0V_LDO_OUT12";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo13_reg: LDO13 {
+ regulator-name = "P1.8V_LDO_OUT13";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo14_reg: LDO14 {
+ regulator-name = "P1.8V_LDO_OUT14";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo15_reg: LDO15 {
+ regulator-name = "P1.0V_LDO_OUT15";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo16_reg: LDO16 {
+ regulator-name = "P1.8V_LDO_OUT16";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo17_reg: LDO17 {
+ regulator-name = "P2.8V_LDO_OUT17";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo25_reg: LDO25 {
+ regulator-name = "vdd_bridge";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK5 {
+ regulator-name = "P1.8V_BUCK_OUT5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ BUCK6 {
+ regulator-name = "P1.2V_BUCK_OUT6";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <0>;
+ };
+
+ BUCK9 {
+ regulator-name = "vdd_ummc";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+ };
+ };
+};
+
+&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+};
+
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ cros_ec: embedded-controller {
+ compatible = "google,cros-ec-i2c";
+ reg = <0x1e>;
+ interrupts = <6 0>;
+ interrupt-parent = <&gpx1>;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_irq>;
+ };
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+&mmc_1 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
+&pinctrl_0 {
+ dp_hpd_gpio: dp-hpd-gpio {
+ samsung,pins = "gpc3-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_dvs: s5m8767-dvs {
+ samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ power_key_irq: power-key-irq {
+ samsung,pins = "gpx1-3";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_ds: s5m8767-ds {
+ samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_irq: s5m8767-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ lid_irq: lid-irq {
+ samsung,pins = "gpx3-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ hsic_reset: hsic-reset {
+ samsung,pins = "gpe1-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd1_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cd {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_bus4 {
+ samsung,pin-drv = <0>;
+};
+
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
+&usbdrd_phy {
+ vbus-supply = <&usb3_vbus_reg>;
+};
+
+#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Andreas Färber, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
open list
Adds initial support for the HP Chromebook 11.
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
---
v2 -> v3:
* Use GPIO_ACTIVE_{LOW,HIGH} (Doug Anderson)
* Use symbolic KEY_POWER instead of comment
* Moved hsic_reset to new USB3503 node's reset-gpios (Vincent Palatin)
* Use dp_hpd_gpio for dp-controller (Doug Anderson, Ajay Kumar)
* Override sd1_{clk,cmd,cd,bus4} pinctrl similar to Snow (Doug Anderson)
* Added ec_irq pinctrl for cros_ec (Doug Anderson)
* Reordered nodes to minimize diff against Snow (Doug Anderson)
* Dropped obsolete mmc_2 override (Doug Anderson)
* Added lid-switch node (Doug Anderson)
* Added gpio-keys pinctrl (Doug Anderson)
* Added bootargs to avoid empty /chosen node and to document console setting
* Renamed s5m8767_pmic node to avoid underscore
* Use new style for overriding inherited pinctrl nodes, too
* Enable i2s0 node
v1 -> v2:
* Use label-based overriding/extension of nodes. (Doug Anderson)
* Dropped tps65090 for now, until we know where to place it.
* Dropped non-Spring nodes from -cros-common.dtsi rather than disabling them.
* Enabled a missing MMC node for access to internal storage.
* Dropped display-timings from dp-controller node. (Ajay Kumar)
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5250-spring.dts | 539 ++++++++++++++++++++++++++++++++
2 files changed, 540 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 80a781f76e88..dec4c292f63d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos5250-arndale.dtb \
exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \
+ exynos5250-spring.dtb \
exynos5260-xyref5260.dtb \
exynos5410-smdk5410.dtb \
exynos5420-arndale-octa.dtb \
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
new file mode 100644
index 000000000000..bcca892bf2ff
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -0,0 +1,539 @@
+/*
+ * Google Spring board device tree source
+ *
+ * Copyright (c) 2013 Google, Inc
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "exynos5250.dtsi"
+
+/ {
+ model = "Google Spring";
+ compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ bootargs = "console=tty1";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_key_irq>, <&lid_irq>;
+
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+
+ lid-switch {
+ label = "Lid";
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0>; /* SW_LID */
+ debounce-interval = <1>;
+ gpio-key,wakeup;
+ };
+ };
+
+ usb3_vbus_reg: regulator-usb3 {
+ compatible = "regulator-fixed";
+ regulator-name = "P5.0V_USB3CON";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpe1 0 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ };
+
+ usb@12110000 {
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503a";
+ reset-gpios = <&hsic_reset>;
+ };
+
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ hdmi {
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
+ hdmi-en-supply = <&s5m_ldo8_reg>;
+ vdd-supply = <&s5m_ldo8_reg>;
+ vdd_osc-supply = <&s5m_ldo10_reg>;
+ vdd_pll-supply = <&s5m_ldo8_reg>;
+ };
+
+ fimd@14400000 {
+ status = "okay";
+ samsung,invert-vclk;
+ };
+
+ dp-controller@145B0000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hpd_gpio>;
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <1>;
+ samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ s5m8767-pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+ wakeup-source;
+
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
+ <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+ <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
+ <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+ <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+
+ /*
+ * The following arrays of DVS voltages are not used, since we are
+ * not using GPIOs to control PMIC bucks, but they must be defined
+ * to please the driver.
+ */
+ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1000000>, <1000000>,
+ <1000000>, <1000000>;
+
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ clocks {
+ compatible = "samsung,s5m8767-clk";
+ #clock-cells = <1>;
+ clock-output-names = "en32khz_ap",
+ "en32khz_cp",
+ "en32khz_bt";
+ };
+
+ regulators {
+ s5m_ldo4_reg: LDO4 {
+ regulator-name = "P1.0V_LDO_OUT4";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo5_reg: LDO5 {
+ regulator-name = "P1.0V_LDO_OUT5";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo6_reg: LDO6 {
+ regulator-name = "vdd_mydp";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo7_reg: LDO7 {
+ regulator-name = "P1.1V_LDO_OUT7";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo8_reg: LDO8 {
+ regulator-name = "P1.0V_LDO_OUT8";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo10_reg: LDO10 {
+ regulator-name = "P1.8V_LDO_OUT10";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo11_reg: LDO11 {
+ regulator-name = "P1.8V_LDO_OUT11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo12_reg: LDO12 {
+ regulator-name = "P3.0V_LDO_OUT12";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo13_reg: LDO13 {
+ regulator-name = "P1.8V_LDO_OUT13";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo14_reg: LDO14 {
+ regulator-name = "P1.8V_LDO_OUT14";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo15_reg: LDO15 {
+ regulator-name = "P1.0V_LDO_OUT15";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo16_reg: LDO16 {
+ regulator-name = "P1.8V_LDO_OUT16";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo17_reg: LDO17 {
+ regulator-name = "P2.8V_LDO_OUT17";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo25_reg: LDO25 {
+ regulator-name = "vdd_bridge";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK5 {
+ regulator-name = "P1.8V_BUCK_OUT5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ BUCK6 {
+ regulator-name = "P1.2V_BUCK_OUT6";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <0>;
+ };
+
+ BUCK9 {
+ regulator-name = "vdd_ummc";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+ };
+ };
+};
+
+&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+};
+
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ cros_ec: embedded-controller {
+ compatible = "google,cros-ec-i2c";
+ reg = <0x1e>;
+ interrupts = <6 0>;
+ interrupt-parent = <&gpx1>;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_irq>;
+ };
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+&mmc_1 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
+&pinctrl_0 {
+ dp_hpd_gpio: dp-hpd-gpio {
+ samsung,pins = "gpc3-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_dvs: s5m8767-dvs {
+ samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ power_key_irq: power-key-irq {
+ samsung,pins = "gpx1-3";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_ds: s5m8767-ds {
+ samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_irq: s5m8767-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ lid_irq: lid-irq {
+ samsung,pins = "gpx3-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ hsic_reset: hsic-reset {
+ samsung,pins = "gpe1-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd1_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cd {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_bus4 {
+ samsung,pin-drv = <0>;
+};
+
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
+&usbdrd_phy {
+ vbus-supply = <&usb3_vbus_reg>;
+};
+
+#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-30 13:50 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 13:50 UTC (permalink / raw)
To: linux-arm-kernel
Adds initial support for the HP Chromebook 11.
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: Andreas F?rber <afaerber@suse.de>
---
v2 -> v3:
* Use GPIO_ACTIVE_{LOW,HIGH} (Doug Anderson)
* Use symbolic KEY_POWER instead of comment
* Moved hsic_reset to new USB3503 node's reset-gpios (Vincent Palatin)
* Use dp_hpd_gpio for dp-controller (Doug Anderson, Ajay Kumar)
* Override sd1_{clk,cmd,cd,bus4} pinctrl similar to Snow (Doug Anderson)
* Added ec_irq pinctrl for cros_ec (Doug Anderson)
* Reordered nodes to minimize diff against Snow (Doug Anderson)
* Dropped obsolete mmc_2 override (Doug Anderson)
* Added lid-switch node (Doug Anderson)
* Added gpio-keys pinctrl (Doug Anderson)
* Added bootargs to avoid empty /chosen node and to document console setting
* Renamed s5m8767_pmic node to avoid underscore
* Use new style for overriding inherited pinctrl nodes, too
* Enable i2s0 node
v1 -> v2:
* Use label-based overriding/extension of nodes. (Doug Anderson)
* Dropped tps65090 for now, until we know where to place it.
* Dropped non-Spring nodes from -cros-common.dtsi rather than disabling them.
* Enabled a missing MMC node for access to internal storage.
* Dropped display-timings from dp-controller node. (Ajay Kumar)
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5250-spring.dts | 539 ++++++++++++++++++++++++++++++++
2 files changed, 540 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 80a781f76e88..dec4c292f63d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos5250-arndale.dtb \
exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \
+ exynos5250-spring.dtb \
exynos5260-xyref5260.dtb \
exynos5410-smdk5410.dtb \
exynos5420-arndale-octa.dtb \
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
new file mode 100644
index 000000000000..bcca892bf2ff
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -0,0 +1,539 @@
+/*
+ * Google Spring board device tree source
+ *
+ * Copyright (c) 2013 Google, Inc
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "exynos5250.dtsi"
+
+/ {
+ model = "Google Spring";
+ compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ bootargs = "console=tty1";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_key_irq>, <&lid_irq>;
+
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+
+ lid-switch {
+ label = "Lid";
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0>; /* SW_LID */
+ debounce-interval = <1>;
+ gpio-key,wakeup;
+ };
+ };
+
+ usb3_vbus_reg: regulator-usb3 {
+ compatible = "regulator-fixed";
+ regulator-name = "P5.0V_USB3CON";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpe1 0 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ };
+
+ usb at 12110000 {
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503a";
+ reset-gpios = <&hsic_reset>;
+ };
+
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ hdmi {
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
+ hdmi-en-supply = <&s5m_ldo8_reg>;
+ vdd-supply = <&s5m_ldo8_reg>;
+ vdd_osc-supply = <&s5m_ldo10_reg>;
+ vdd_pll-supply = <&s5m_ldo8_reg>;
+ };
+
+ fimd at 14400000 {
+ status = "okay";
+ samsung,invert-vclk;
+ };
+
+ dp-controller at 145B0000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hpd_gpio>;
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <1>;
+ samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ s5m8767-pmic at 66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+ wakeup-source;
+
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
+ <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+ <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
+ <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+ <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+
+ /*
+ * The following arrays of DVS voltages are not used, since we are
+ * not using GPIOs to control PMIC bucks, but they must be defined
+ * to please the driver.
+ */
+ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1000000>, <1000000>,
+ <1000000>, <1000000>;
+
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ clocks {
+ compatible = "samsung,s5m8767-clk";
+ #clock-cells = <1>;
+ clock-output-names = "en32khz_ap",
+ "en32khz_cp",
+ "en32khz_bt";
+ };
+
+ regulators {
+ s5m_ldo4_reg: LDO4 {
+ regulator-name = "P1.0V_LDO_OUT4";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo5_reg: LDO5 {
+ regulator-name = "P1.0V_LDO_OUT5";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo6_reg: LDO6 {
+ regulator-name = "vdd_mydp";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo7_reg: LDO7 {
+ regulator-name = "P1.1V_LDO_OUT7";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo8_reg: LDO8 {
+ regulator-name = "P1.0V_LDO_OUT8";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo10_reg: LDO10 {
+ regulator-name = "P1.8V_LDO_OUT10";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo11_reg: LDO11 {
+ regulator-name = "P1.8V_LDO_OUT11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo12_reg: LDO12 {
+ regulator-name = "P3.0V_LDO_OUT12";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo13_reg: LDO13 {
+ regulator-name = "P1.8V_LDO_OUT13";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo14_reg: LDO14 {
+ regulator-name = "P1.8V_LDO_OUT14";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo15_reg: LDO15 {
+ regulator-name = "P1.0V_LDO_OUT15";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo16_reg: LDO16 {
+ regulator-name = "P1.8V_LDO_OUT16";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo17_reg: LDO17 {
+ regulator-name = "P2.8V_LDO_OUT17";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo25_reg: LDO25 {
+ regulator-name = "vdd_bridge";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ BUCK5 {
+ regulator-name = "P1.8V_BUCK_OUT5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ BUCK6 {
+ regulator-name = "P1.2V_BUCK_OUT6";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <0>;
+ };
+
+ BUCK9 {
+ regulator-name = "vdd_ummc";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+ };
+ };
+};
+
+&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+};
+
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc at 50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ cros_ec: embedded-controller {
+ compatible = "google,cros-ec-i2c";
+ reg = <0x1e>;
+ interrupts = <6 0>;
+ interrupt-parent = <&gpx1>;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_irq>;
+ };
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy at 38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot at 0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+&mmc_1 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
+
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
+&pinctrl_0 {
+ dp_hpd_gpio: dp-hpd-gpio {
+ samsung,pins = "gpc3-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_dvs: s5m8767-dvs {
+ samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ power_key_irq: power-key-irq {
+ samsung,pins = "gpx1-3";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_ds: s5m8767-ds {
+ samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_irq: s5m8767-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ lid_irq: lid-irq {
+ samsung,pins = "gpx3-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ hsic_reset: hsic-reset {
+ samsung,pins = "gpe1-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd1_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cd {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_bus4 {
+ samsung,pin-drv = <0>;
+};
+
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
+&usbdrd_phy {
+ vbus-supply = <&usb3_vbus_reg>;
+};
+
+#include "cros-ec-keyboard.dtsi"
--
1.9.3
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: [PATCH v3 0/4] ARM: dts: exynos: Prepare Spring
2014-07-30 13:50 ` Andreas Färber
@ 2014-07-30 14:17 ` Andreas Färber
-1 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 14:17 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas
[-- Attachment #1: Type: text/plain, Size: 553 bytes --]
Am 30.07.2014 15:50, schrieb Andreas Färber:
> Hello,
>
> Based on the preinstalled 3.8 based ChromeOS kernel and previous 3.15
> based attempts by Stephan and me that broke for 3.16, I've prepared a
> device tree for the HP Chromebook 11 aka Google Spring.
>
> v3 mainly does style cleanups, aligning Snow and Spring better.
And for your review convenience I attach the Snow vs. Spring diff.
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
[-- Attachment #2: spring-snow.v3.diff --]
[-- Type: text/x-patch, Size: 17407 bytes --]
--- arch/arm/boot/dts/exynos5250-snow.dts 2014-07-30 15:45:47.830000417 +0200
+++ arch/arm/boot/dts/exynos5250-spring.dts 2014-07-30 16:10:06.715001113 +0200
@@ -1,12 +1,13 @@
/*
- * Google Snow board device tree source
+ * Google Spring board device tree source
*
- * Copyright (c) 2012 Google, Inc
+ * Copyright (c) 2013 Google, Inc
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
-*/
+ */
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
@@ -14,26 +15,21 @@
#include "exynos5250.dtsi"
/ {
- model = "Google Snow";
- compatible = "google,snow", "samsung,exynos5250", "samsung,exynos5";
-
- aliases {
- i2c104 = &i2c_104;
- };
+ model = "Google Spring";
+ compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
memory {
reg = <0x40000000 0x80000000>;
};
chosen {
- };
-
- rtc@101E0000 {
- status = "okay";
+ bootargs = "console=tty1";
};
gpio-keys {
compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_key_irq>, <&lid_irq>;
power {
label = "Power";
@@ -52,145 +48,12 @@
};
};
- vbat: vbat-fixed-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vbat-supply";
- regulator-boot-on;
- };
-
- i2c-arbitrator {
- compatible = "i2c-arb-gpio-challenge";
- #address-cells = <1>;
- #size-cells = <0>;
-
- i2c-parent = <&{/i2c@12CA0000}>;
-
- our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
- their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
- slew-delay-us = <10>;
- wait-retry-us = <3000>;
- wait-free-us = <50000>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&arb_our_claim &arb_their_claim>;
-
- /* Use ID 104 as a hint that we're on physical bus 4 */
- i2c_104: i2c@0 {
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- battery: sbs-battery@b {
- compatible = "sbs,sbs-battery";
- reg = <0xb>;
- sbs,poll-retry-count = <1>;
- };
-
- cros_ec: embedded-controller {
- compatible = "google,cros-ec-i2c";
- reg = <0x1e>;
- interrupts = <6 0>;
- interrupt-parent = <&gpx1>;
- pinctrl-names = "default";
- pinctrl-0 = <&ec_irq>;
- wakeup-source;
- };
-
- power-regulator {
- compatible = "ti,tps65090";
- reg = <0x48>;
-
- /*
- * Config irq to disable internal pulls
- * even though we run in polling mode.
- */
- pinctrl-names = "default";
- pinctrl-0 = <&tps65090_irq>;
-
- vsys1-supply = <&vbat>;
- vsys2-supply = <&vbat>;
- vsys3-supply = <&vbat>;
- infet1-supply = <&vbat>;
- infet2-supply = <&vbat>;
- infet3-supply = <&vbat>;
- infet4-supply = <&vbat>;
- infet5-supply = <&vbat>;
- infet6-supply = <&vbat>;
- infet7-supply = <&vbat>;
- vsys-l1-supply = <&vbat>;
- vsys-l2-supply = <&vbat>;
-
- regulators {
- dcdc1 {
- ti,enable-ext-control;
- };
- dcdc2 {
- ti,enable-ext-control;
- };
- dcdc3 {
- ti,enable-ext-control;
- };
- fet1 {
- regulator-name = "vcd_led";
- ti,overcurrent-wait = <3>;
- };
- tps65090_fet2: fet2 {
- regulator-name = "video_mid";
- regulator-always-on;
- ti,overcurrent-wait = <3>;
- };
- fet3 {
- regulator-name = "wwan_r";
- regulator-always-on;
- ti,overcurrent-wait = <3>;
- };
- fet4 {
- regulator-name = "sdcard";
- ti,overcurrent-wait = <3>;
- };
- fet5 {
- regulator-name = "camout";
- regulator-always-on;
- ti,overcurrent-wait = <3>;
- };
- fet6 {
- regulator-name = "lcd_vdd";
- ti,overcurrent-wait = <3>;
- };
- tps65090_fet7: fet7 {
- regulator-name = "video_mid_1a";
- regulator-always-on;
- ti,overcurrent-wait = <3>;
- };
- ldo1 {
- };
- ldo2 {
- };
- };
-
- charger {
- compatible = "ti,tps65090-charger";
- };
- };
- };
- };
-
- sound {
- compatible = "google,snow-audio-max98095";
-
- samsung,model = "Snow-I2S-MAX98095";
- samsung,i2s-controller = <&i2s0>;
- samsung,audio-codec = <&max98095>;
- };
-
usb3_vbus_reg: regulator-usb3 {
compatible = "regulator-fixed";
regulator-name = "P5.0V_USB3CON";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb3_vbus_en>;
+ gpio = <&gpe1 0 GPIO_ACTIVE_LOW>;
enable-active-high;
};
@@ -198,6 +61,11 @@
samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
};
+ usb-hub {
+ compatible = "smsc,usb3503a";
+ reset-gpios = <&hsic_reset>;
+ };
+
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
@@ -211,19 +79,10 @@
pinctrl-0 = <&hdmi_hpd_irq>;
phy = <&hdmiphy>;
ddc = <&i2c_2>;
- hdmi-en-supply = <&tps65090_fet7>;
- vdd-supply = <&ldo8_reg>;
- vdd_osc-supply = <&ldo10_reg>;
- vdd_pll-supply = <&ldo8_reg>;
- };
-
- backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 0 1000000 0>;
- brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
- default-brightness-level = <7>;
- pinctrl-0 = <&pwm0_out>;
- pinctrl-names = "default";
+ hdmi-en-supply = <&s5m_ldo8_reg>;
+ vdd-supply = <&s5m_ldo8_reg>;
+ vdd_osc-supply = <&s5m_ldo10_reg>;
+ vdd_pll-supply = <&s5m_ldo8_reg>;
};
fimd@14400000 {
@@ -234,30 +93,14 @@
dp-controller@145B0000 {
status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&dp_hpd>;
+ pinctrl-0 = <&dp_hpd_gpio>;
samsung,color-space = <0>;
samsung,dynamic-range = <0>;
samsung,ycbcr-coeff = <0>;
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
- samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
-
- display-timings {
- native-mode = <&timing1>;
-
- timing1: timing@1 {
- clock-frequency = <70589280>;
- hactive = <1366>;
- vactive = <768>;
- hfront-porch = <40>;
- hback-porch = <40>;
- hsync-len = <32>;
- vback-porch = <10>;
- vfront-porch = <12>;
- vsync-len = <6>;
- };
- };
+ samsung,lane-count = <1>;
+ samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
};
};
@@ -266,146 +109,224 @@
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <378000>;
- max77686@09 {
- compatible = "maxim,max77686";
+ s5m8767-pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
interrupt-parent = <&gpx3>;
interrupts = <2 0>;
pinctrl-names = "default";
- pinctrl-0 = <&max77686_irq>;
+ pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
wakeup-source;
- reg = <0x09>;
- #clock-cells = <1>;
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "P1.0V_LDO_OUT1";
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
+ <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+ <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
+ <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+ <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+
+ /*
+ * The following arrays of DVS voltages are not used, since we are
+ * not using GPIOs to control PMIC bucks, but they must be defined
+ * to please the driver.
+ */
+ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1000000>, <1000000>,
+ <1000000>, <1000000>;
+
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ clocks {
+ compatible = "samsung,s5m8767-clk";
+ #clock-cells = <1>;
+ clock-output-names = "en32khz_ap",
+ "en32khz_cp",
+ "en32khz_bt";
+ };
+
+ regulators {
+ s5m_ldo4_reg: LDO4 {
+ regulator-name = "P1.0V_LDO_OUT4";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+ op_mode = <0>;
};
- ldo2_reg: LDO2 {
- regulator-name = "P1.8V_LDO_OUT2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
+ s5m_ldo5_reg: LDO5 {
+ regulator-name = "P1.0V_LDO_OUT5";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
regulator-always-on;
+ op_mode = <0>;
};
- ldo3_reg: LDO3 {
- regulator-name = "P1.8V_LDO_OUT3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
+ s5m_ldo6_reg: LDO6 {
+ regulator-name = "vdd_mydp";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
regulator-always-on;
+ op_mode = <3>;
};
- ldo7_reg: LDO7 {
+ s5m_ldo7_reg: LDO7 {
regulator-name = "P1.1V_LDO_OUT7";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
+ op_mode = <3>;
};
- ldo8_reg: LDO8 {
+ s5m_ldo8_reg: LDO8 {
regulator-name = "P1.0V_LDO_OUT8";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+ op_mode = <3>;
};
- ldo10_reg: LDO10 {
+ s5m_ldo10_reg: LDO10 {
regulator-name = "P1.8V_LDO_OUT10";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo11_reg: LDO11 {
+ regulator-name = "P1.8V_LDO_OUT11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
};
- ldo12_reg: LDO12 {
+ s5m_ldo12_reg: LDO12 {
regulator-name = "P3.0V_LDO_OUT12";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
+ op_mode = <3>;
};
- ldo14_reg: LDO14 {
+ s5m_ldo13_reg: LDO13 {
+ regulator-name = "P1.8V_LDO_OUT13";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ s5m_ldo14_reg: LDO14 {
regulator-name = "P1.8V_LDO_OUT14";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
+ op_mode = <3>;
};
- ldo15_reg: LDO15 {
+ s5m_ldo15_reg: LDO15 {
regulator-name = "P1.0V_LDO_OUT15";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+ op_mode = <3>;
};
- ldo16_reg: LDO16 {
+ s5m_ldo16_reg: LDO16 {
regulator-name = "P1.8V_LDO_OUT16";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
+ op_mode = <3>;
+ };
+
+ s5m_ldo17_reg: LDO17 {
+ regulator-name = "P2.8V_LDO_OUT17";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <0>;
};
- buck1_reg: BUCK1 {
+ s5m_ldo25_reg: LDO25 {
+ regulator-name = "vdd_bridge";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ BUCK1 {
regulator-name = "vdd_mif";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
+ op_mode = <3>;
};
- buck2_reg: BUCK2 {
+ BUCK2 {
regulator-name = "vdd_arm";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
+ op_mode = <3>;
};
- buck3_reg: BUCK3 {
+ BUCK3 {
regulator-name = "vdd_int";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
+ op_mode = <3>;
};
- buck4_reg: BUCK4 {
+ BUCK4 {
regulator-name = "vdd_g3d";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1300000>;
- regulator-always-on;
regulator-boot-on;
+ op_mode = <3>;
};
- buck5_reg: BUCK5 {
+ BUCK5 {
regulator-name = "P1.8V_BUCK_OUT5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
+ op_mode = <1>;
};
- buck6_reg: BUCK6 {
- regulator-name = "P1.35V_BUCK_OUT6";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "P2.0V_BUCK_OUT7";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
+ BUCK6 {
+ regulator-name = "P1.2V_BUCK_OUT6";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
regulator-always-on;
+ regulator-boot-on;
+ op_mode = <0>;
};
- buck8_reg: BUCK8 {
- regulator-name = "P2.85V_BUCK_OUT8";
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
+ BUCK9 {
+ regulator-name = "vdd_ummc";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <3000000>;
regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
};
};
};
@@ -415,14 +336,6 @@
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <378000>;
-
- trackpad {
- reg = <0x67>;
- compatible = "cypress,cyapa";
- interrupts = <2 0>;
- interrupt-parent = <&gpx1>;
- wakeup-source;
- };
};
/*
@@ -454,6 +367,16 @@
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
+
+ cros_ec: embedded-controller {
+ compatible = "google,cros-ec-i2c";
+ reg = <0x1e>;
+ interrupts = <6 0>;
+ interrupt-parent = <&gpx1>;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_irq>;
+ };
};
&i2c_5 {
@@ -466,13 +389,6 @@
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
-
- max98095: codec@11 {
- compatible = "maxim,max98095";
- reg = <0x11>;
- pinctrl-0 = <&max98095_en>;
- pinctrl-names = "default";
- };
};
&i2c_8 {
@@ -508,49 +424,41 @@
};
};
-&mmc_2 {
+&mmc_1 {
status = "okay";
num-slots = <1>;
supports-highspeed;
+ broken-cd;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
slot@0 {
reg = <0>;
bus-width = <4>;
- wp-gpios = <&gpc2 1 0>;
};
};
-/*
- * On Snow we've got SIP WiFi and so can keep drive strengths low to
- * reduce EMI.
- */
-&mmc_3 {
- status = "okay";
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+&pinctrl_0 {
+ dp_hpd_gpio: dp-hpd-gpio {
+ samsung,pins = "gpc3-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
- slot@0 {
- reg = <0>;
- bus-width = <4>;
+ s5m8767_dvs: s5m8767-dvs {
+ samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
};
-};
-&pinctrl_0 {
- max77686_irq: max77686-irq {
- samsung,pins = "gpx3-2";
+ power_key_irq: power-key-irq {
+ samsung,pins = "gpx1-3";
samsung,pin-function = <0>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
@@ -563,23 +471,23 @@
samsung,pin-drv = <0>;
};
- max98095_en: max98095-en {
- samsung,pins = "gpx1-7";
+ s5m8767_ds: s5m8767-ds {
+ samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
+ samsung,pin-pud = <1>;
samsung,pin-drv = <0>;
};
- tps65090_irq: tps65090-irq {
- samsung,pins = "gpx2-6";
+ s5m8767_irq: s5m8767-irq {
+ samsung,pins = "gpx3-2";
samsung,pin-function = <0>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
- usb3_vbus_en: usb3-vbus-en {
- samsung,pins = "gpx2-7";
- samsung,pin-function = <1>;
+ lid_irq: lid-irq {
+ samsung,pins = "gpx3-5";
+ samsung,pin-function = <0>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
@@ -593,31 +501,28 @@
};
&pinctrl_1 {
- arb_their_claim: arb-their-claim {
- samsung,pins = "gpe0-4";
- samsung,pin-function = <0>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- arb_our_claim: arb-our-claim {
- samsung,pins = "gpf0-3";
+ hsic_reset: hsic-reset {
+ samsung,pins = "gpe1-0";
samsung,pin-function = <1>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
-&sd3_clk {
+&sd1_clk {
samsung,pin-drv = <0>;
};
-&sd3_cmd {
+&sd1_cmd {
samsung,pin-pud = <3>;
samsung,pin-drv = <0>;
};
-&sd3_bus4 {
+&sd1_cd {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_bus4 {
samsung,pin-drv = <0>;
};
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 0/4] ARM: dts: exynos: Prepare Spring
@ 2014-07-30 14:17 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-30 14:17 UTC (permalink / raw)
To: linux-arm-kernel
Am 30.07.2014 15:50, schrieb Andreas F?rber:
> Hello,
>
> Based on the preinstalled 3.8 based ChromeOS kernel and previous 3.15
> based attempts by Stephan and me that broke for 3.16, I've prepared a
> device tree for the HP Chromebook 11 aka Google Spring.
>
> v3 mainly does style cleanups, aligning Snow and Spring better.
And for your review convenience I attach the Snow vs. Spring diff.
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg
-------------- next part --------------
A non-text attachment was scrubbed...
Name: spring-snow.v3.diff
Type: text/x-patch
Size: 17407 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140730/a99e2600/attachment-0001.bin>
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:26 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-31 9:26 UTC (permalink / raw)
To: linux-samsung-soc
Cc: linux-arm-kernel, devicetree, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Ben Dooks, Kukjin Kim, LKML, Ajay Kumar
Am 30.07.2014 15:50, schrieb Andreas Färber:
> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
> new file mode 100644
> index 000000000000..bcca892bf2ff
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
[...]
> +&pinctrl_0 {
> + dp_hpd_gpio: dp-hpd-gpio {
> + samsung,pins = "gpc3-0";
> + samsung,pin-function = <1>;
Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
Seeing that Ajay called this node dp-hdp, it should probably be an override?
&dp_hpd {
...
};
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:26 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-31 9:26 UTC (permalink / raw)
To: linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Ben Dooks, Kukjin Kim, LKML, Ajay Kumar
Am 30.07.2014 15:50, schrieb Andreas Färber:
> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
> new file mode 100644
> index 000000000000..bcca892bf2ff
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
[...]
> +&pinctrl_0 {
> + dp_hpd_gpio: dp-hpd-gpio {
> + samsung,pins = "gpc3-0";
> + samsung,pin-function = <1>;
Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
Seeing that Ajay called this node dp-hdp, it should probably be an override?
&dp_hpd {
...
};
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:26 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-31 9:26 UTC (permalink / raw)
To: linux-arm-kernel
Am 30.07.2014 15:50, schrieb Andreas F?rber:
> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
> new file mode 100644
> index 000000000000..bcca892bf2ff
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
[...]
> +&pinctrl_0 {
> + dp_hpd_gpio: dp-hpd-gpio {
> + samsung,pins = "gpc3-0";
> + samsung,pin-function = <1>;
Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
Seeing that Ajay called this node dp-hdp, it should probably be an override?
&dp_hpd {
...
};
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
2014-07-31 9:26 ` Andreas Färber
(?)
@ 2014-07-31 9:49 ` Ajay kumar
-1 siblings, 0 replies; 28+ messages in thread
From: Ajay kumar @ 2014-07-31 9:49 UTC (permalink / raw)
To: Andreas Färber
Cc: linux-samsung-soc, linux-arm-kernel, devicetree,
Stephan van Schaik, Vincent Palatin, Doug Anderson,
Javier Martinez Canillas, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
LKML, Ajay Kumar
Hi Andreas,
On Thu, Jul 31, 2014 at 2:56 PM, Andreas Färber <afaerber@suse.de> wrote:
> Am 30.07.2014 15:50, schrieb Andreas Färber:
>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>> new file mode 100644
>> index 000000000000..bcca892bf2ff
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
> [...]
>> +&pinctrl_0 {
>> + dp_hpd_gpio: dp-hpd-gpio {
>> + samsung,pins = "gpc3-0";
>> + samsung,pin-function = <1>;
>
> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
Right, this should be 0.
>> + samsung,pin-pud = <3>;
>> + samsung,pin-drv = <0>;
>> + };
>
> Seeing that Ajay called this node dp-hdp, it should probably be an override?
dp_hpd should be enough. I will keep the same name for peach boards.
dp_hpd: dp-hpd {
.
.
.
};
Ajay
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:49 ` Ajay kumar
0 siblings, 0 replies; 28+ messages in thread
From: Ajay kumar @ 2014-07-31 9:49 UTC (permalink / raw)
To: Andreas Färber
Cc: linux-samsung-soc, linux-arm-kernel, devicetree,
Stephan van Schaik, Vincent Palatin, Doug Anderson,
Javier Martinez Canillas, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
LKML, Ajay Kumar
Hi Andreas,
On Thu, Jul 31, 2014 at 2:56 PM, Andreas Färber <afaerber@suse.de> wrote:
> Am 30.07.2014 15:50, schrieb Andreas Färber:
>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>> new file mode 100644
>> index 000000000000..bcca892bf2ff
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
> [...]
>> +&pinctrl_0 {
>> + dp_hpd_gpio: dp-hpd-gpio {
>> + samsung,pins = "gpc3-0";
>> + samsung,pin-function = <1>;
>
> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
Right, this should be 0.
>> + samsung,pin-pud = <3>;
>> + samsung,pin-drv = <0>;
>> + };
>
> Seeing that Ajay called this node dp-hdp, it should probably be an override?
dp_hpd should be enough. I will keep the same name for peach boards.
dp_hpd: dp-hpd {
.
.
.
};
Ajay
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:49 ` Ajay kumar
0 siblings, 0 replies; 28+ messages in thread
From: Ajay kumar @ 2014-07-31 9:49 UTC (permalink / raw)
To: linux-arm-kernel
Hi Andreas,
On Thu, Jul 31, 2014 at 2:56 PM, Andreas F?rber <afaerber@suse.de> wrote:
> Am 30.07.2014 15:50, schrieb Andreas F?rber:
>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>> new file mode 100644
>> index 000000000000..bcca892bf2ff
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
> [...]
>> +&pinctrl_0 {
>> + dp_hpd_gpio: dp-hpd-gpio {
>> + samsung,pins = "gpc3-0";
>> + samsung,pin-function = <1>;
>
> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
Right, this should be 0.
>> + samsung,pin-pud = <3>;
>> + samsung,pin-drv = <0>;
>> + };
>
> Seeing that Ajay called this node dp-hdp, it should probably be an override?
dp_hpd should be enough. I will keep the same name for peach boards.
dp_hpd: dp-hpd {
.
.
.
};
Ajay
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:53 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-31 9:53 UTC (permalink / raw)
To: Ajay kumar
Cc: linux-samsung-soc, linux-arm-kernel, devicetree,
Stephan van Schaik, Vincent Palatin, Doug Anderson,
Javier Martinez Canillas, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
LKML, Ajay Kumar
Hi,
Am 31.07.2014 11:49, schrieb Ajay kumar:
> On Thu, Jul 31, 2014 at 2:56 PM, Andreas Färber <afaerber@suse.de> wrote:
>> Am 30.07.2014 15:50, schrieb Andreas Färber:
>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>>> new file mode 100644
>>> index 000000000000..bcca892bf2ff
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>> [...]
>>> +&pinctrl_0 {
>>> + dp_hpd_gpio: dp-hpd-gpio {
>>> + samsung,pins = "gpc3-0";
>>> + samsung,pin-function = <1>;
>>
>> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
> Right, this should be 0.
>
>>> + samsung,pin-pud = <3>;
>>> + samsung,pin-drv = <0>;
>>> + };
>>
>> Seeing that Ajay called this node dp-hdp, it should probably be an override?
> dp_hpd should be enough. I will keep the same name for peach boards.
> dp_hpd: dp-hpd {
> .
> .
> .
> };
Apart from my own set of typos, I see that you proposed dp-hpd whereas
-pinctrl.dtsi has dp_hpd (dash vs. underscore). My question is, can we
override the pinctrl one instead of adding a new one, or do they need to
coexist?
Thanks,
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:53 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-31 9:53 UTC (permalink / raw)
To: Ajay kumar
Cc: linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Stephan van Schaik,
Vincent Palatin, Doug Anderson, Javier Martinez Canillas,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Ben Dooks, Kukjin Kim, LKML, Ajay Kumar
Hi,
Am 31.07.2014 11:49, schrieb Ajay kumar:
> On Thu, Jul 31, 2014 at 2:56 PM, Andreas Färber <afaerber@suse.de> wrote:
>> Am 30.07.2014 15:50, schrieb Andreas Färber:
>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>>> new file mode 100644
>>> index 000000000000..bcca892bf2ff
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>> [...]
>>> +&pinctrl_0 {
>>> + dp_hpd_gpio: dp-hpd-gpio {
>>> + samsung,pins = "gpc3-0";
>>> + samsung,pin-function = <1>;
>>
>> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
> Right, this should be 0.
>
>>> + samsung,pin-pud = <3>;
>>> + samsung,pin-drv = <0>;
>>> + };
>>
>> Seeing that Ajay called this node dp-hdp, it should probably be an override?
> dp_hpd should be enough. I will keep the same name for peach boards.
> dp_hpd: dp-hpd {
> .
> .
> .
> };
Apart from my own set of typos, I see that you proposed dp-hpd whereas
-pinctrl.dtsi has dp_hpd (dash vs. underscore). My question is, can we
override the pinctrl one instead of adding a new one, or do they need to
coexist?
Thanks,
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 9:53 ` Andreas Färber
0 siblings, 0 replies; 28+ messages in thread
From: Andreas Färber @ 2014-07-31 9:53 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
Am 31.07.2014 11:49, schrieb Ajay kumar:
> On Thu, Jul 31, 2014 at 2:56 PM, Andreas F?rber <afaerber@suse.de> wrote:
>> Am 30.07.2014 15:50, schrieb Andreas F?rber:
>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>>> new file mode 100644
>>> index 000000000000..bcca892bf2ff
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>> [...]
>>> +&pinctrl_0 {
>>> + dp_hpd_gpio: dp-hpd-gpio {
>>> + samsung,pins = "gpc3-0";
>>> + samsung,pin-function = <1>;
>>
>> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
> Right, this should be 0.
>
>>> + samsung,pin-pud = <3>;
>>> + samsung,pin-drv = <0>;
>>> + };
>>
>> Seeing that Ajay called this node dp-hdp, it should probably be an override?
> dp_hpd should be enough. I will keep the same name for peach boards.
> dp_hpd: dp-hpd {
> .
> .
> .
> };
Apart from my own set of typos, I see that you proposed dp-hpd whereas
-pinctrl.dtsi has dp_hpd (dash vs. underscore). My question is, can we
override the pinctrl one instead of adding a new one, or do they need to
coexist?
Thanks,
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
2014-07-31 9:53 ` Andreas Färber
(?)
@ 2014-07-31 10:01 ` Ajay kumar
-1 siblings, 0 replies; 28+ messages in thread
From: Ajay kumar @ 2014-07-31 10:01 UTC (permalink / raw)
To: Andreas Färber
Cc: linux-samsung-soc, linux-arm-kernel, devicetree,
Stephan van Schaik, Vincent Palatin, Doug Anderson,
Javier Martinez Canillas, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
LKML, Ajay Kumar
On Thu, Jul 31, 2014 at 3:23 PM, Andreas Färber <afaerber@suse.de> wrote:
> Hi,
>
> Am 31.07.2014 11:49, schrieb Ajay kumar:
>> On Thu, Jul 31, 2014 at 2:56 PM, Andreas Färber <afaerber@suse.de> wrote:
>>> Am 30.07.2014 15:50, schrieb Andreas Färber:
>>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>>>> new file mode 100644
>>>> index 000000000000..bcca892bf2ff
>>>> --- /dev/null
>>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>>> [...]
>>>> +&pinctrl_0 {
>>>> + dp_hpd_gpio: dp-hpd-gpio {
>>>> + samsung,pins = "gpc3-0";
>>>> + samsung,pin-function = <1>;
>>>
>>> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
>> Right, this should be 0.
>>
>>>> + samsung,pin-pud = <3>;
>>>> + samsung,pin-drv = <0>;
>>>> + };
>>>
>>> Seeing that Ajay called this node dp-hdp, it should probably be an override?
>> dp_hpd should be enough. I will keep the same name for peach boards.
>> dp_hpd: dp-hpd {
>> .
>> .
>> .
>> };
>
> Apart from my own set of typos, I see that you proposed dp-hpd whereas
> -pinctrl.dtsi has dp_hpd (dash vs. underscore). My question is, can we
> override the pinctrl one instead of adding a new one, or do they need to
> coexist?
The one in exynos5250-pinctrl.dtsi will be used only for smdk5250/snow.
For spring, you can override the same.
Ajay
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 10:01 ` Ajay kumar
0 siblings, 0 replies; 28+ messages in thread
From: Ajay kumar @ 2014-07-31 10:01 UTC (permalink / raw)
To: Andreas Färber
Cc: linux-samsung-soc, linux-arm-kernel, devicetree,
Stephan van Schaik, Vincent Palatin, Doug Anderson,
Javier Martinez Canillas, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Ben Dooks, Kukjin Kim,
LKML, Ajay Kumar
On Thu, Jul 31, 2014 at 3:23 PM, Andreas Färber <afaerber@suse.de> wrote:
> Hi,
>
> Am 31.07.2014 11:49, schrieb Ajay kumar:
>> On Thu, Jul 31, 2014 at 2:56 PM, Andreas Färber <afaerber@suse.de> wrote:
>>> Am 30.07.2014 15:50, schrieb Andreas Färber:
>>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>>>> new file mode 100644
>>>> index 000000000000..bcca892bf2ff
>>>> --- /dev/null
>>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>>> [...]
>>>> +&pinctrl_0 {
>>>> + dp_hpd_gpio: dp-hpd-gpio {
>>>> + samsung,pins = "gpc3-0";
>>>> + samsung,pin-function = <1>;
>>>
>>> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
>> Right, this should be 0.
>>
>>>> + samsung,pin-pud = <3>;
>>>> + samsung,pin-drv = <0>;
>>>> + };
>>>
>>> Seeing that Ajay called this node dp-hdp, it should probably be an override?
>> dp_hpd should be enough. I will keep the same name for peach boards.
>> dp_hpd: dp-hpd {
>> .
>> .
>> .
>> };
>
> Apart from my own set of typos, I see that you proposed dp-hpd whereas
> -pinctrl.dtsi has dp_hpd (dash vs. underscore). My question is, can we
> override the pinctrl one instead of adding a new one, or do they need to
> coexist?
The one in exynos5250-pinctrl.dtsi will be used only for smdk5250/snow.
For spring, you can override the same.
Ajay
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree
@ 2014-07-31 10:01 ` Ajay kumar
0 siblings, 0 replies; 28+ messages in thread
From: Ajay kumar @ 2014-07-31 10:01 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jul 31, 2014 at 3:23 PM, Andreas F?rber <afaerber@suse.de> wrote:
> Hi,
>
> Am 31.07.2014 11:49, schrieb Ajay kumar:
>> On Thu, Jul 31, 2014 at 2:56 PM, Andreas F?rber <afaerber@suse.de> wrote:
>>> Am 30.07.2014 15:50, schrieb Andreas F?rber:
>>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>>>> new file mode 100644
>>>> index 000000000000..bcca892bf2ff
>>>> --- /dev/null
>>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>>> [...]
>>>> +&pinctrl_0 {
>>>> + dp_hpd_gpio: dp-hpd-gpio {
>>>> + samsung,pins = "gpc3-0";
>>>> + samsung,pin-function = <1>;
>>>
>>> Not sure where this 1 came from... Both Ajay and my 3.8 DT have 0.
>> Right, this should be 0.
>>
>>>> + samsung,pin-pud = <3>;
>>>> + samsung,pin-drv = <0>;
>>>> + };
>>>
>>> Seeing that Ajay called this node dp-hdp, it should probably be an override?
>> dp_hpd should be enough. I will keep the same name for peach boards.
>> dp_hpd: dp-hpd {
>> .
>> .
>> .
>> };
>
> Apart from my own set of typos, I see that you proposed dp-hpd whereas
> -pinctrl.dtsi has dp_hpd (dash vs. underscore). My question is, can we
> override the pinctrl one instead of adding a new one, or do they need to
> coexist?
The one in exynos5250-pinctrl.dtsi will be used only for smdk5250/snow.
For spring, you can override the same.
Ajay
^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2014-07-31 10:01 UTC | newest]
Thread overview: 28+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-07-30 13:50 [PATCH v3 0/4] ARM: dts: exynos: Prepare Spring Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` [PATCH v3 1/4] ARM: dts: Fix MMC pinctrl for exynos5250-snow Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` [PATCH v3 2/4] ARM: dts: Fold exynos5250-cros-common into exynos5250-snow Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` [PATCH v3 3/4] ARM: dts: Clean up exynos5250-snow Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` [PATCH v3 4/4] ARM: dts: Add exynos5250-spring device tree Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-30 13:50 ` Andreas Färber
2014-07-31 9:26 ` Andreas Färber
2014-07-31 9:26 ` Andreas Färber
2014-07-31 9:26 ` Andreas Färber
2014-07-31 9:49 ` Ajay kumar
2014-07-31 9:49 ` Ajay kumar
2014-07-31 9:49 ` Ajay kumar
2014-07-31 9:53 ` Andreas Färber
2014-07-31 9:53 ` Andreas Färber
2014-07-31 9:53 ` Andreas Färber
2014-07-31 10:01 ` Ajay kumar
2014-07-31 10:01 ` Ajay kumar
2014-07-31 10:01 ` Ajay kumar
2014-07-30 14:17 ` [PATCH v3 0/4] ARM: dts: exynos: Prepare Spring Andreas Färber
2014-07-30 14:17 ` Andreas Färber
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.