* [PATCH] staging: et131x: Fix errors caused by phydev->addr accesses before initialisation
@ 2014-08-05 22:57 Mark Einon
2014-08-10 4:39 ` Greg KH
0 siblings, 1 reply; 3+ messages in thread
From: Mark Einon @ 2014-08-05 22:57 UTC (permalink / raw)
To: gregkh; +Cc: devel, linux-kernel, netdev, Mark Einon, stable
Fix two reported bugs, caused by et131x_adapter->phydev->addr being accessed
before it is initialised, by:
- letting et131x_mii_write() take a phydev address, instead of using the one
stored in adapter by default. This is so et131x_mdio_write() can use it's own
addr value.
- removing implementation of et131x_mdio_reset(), as it's not needed.
- moving a call to et131x_disable_phy_coma() in et131x_pci_setup(), which uses
phydev->addr, until after the mdiobus has been registered.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80751
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77121
Cc: stable@vger.kernel.org
Signed-off-by: Mark Einon <mark.einon@gmail.com>
---
drivers/staging/et131x/et131x.c | 68 ++++++++++++++++-------------------------
1 file changed, 27 insertions(+), 41 deletions(-)
diff --git a/drivers/staging/et131x/et131x.c b/drivers/staging/et131x/et131x.c
index 8bf1eb4..831b7c6 100644
--- a/drivers/staging/et131x/et131x.c
+++ b/drivers/staging/et131x/et131x.c
@@ -1421,22 +1421,16 @@ static int et131x_mii_read(struct et131x_adapter *adapter, u8 reg, u16 *value)
* @reg: the register to read
* @value: 16-bit value to write
*/
-static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value)
+static int et131x_mii_write(struct et131x_adapter *adapter, u8 addr, u8 reg,
+ u16 value)
{
struct mac_regs __iomem *mac = &adapter->regs->mac;
- struct phy_device *phydev = adapter->phydev;
int status = 0;
- u8 addr;
u32 delay = 0;
u32 mii_addr;
u32 mii_cmd;
u32 mii_indicator;
- if (!phydev)
- return -EIO;
-
- addr = phydev->addr;
-
/* Save a local copy of the registers we are dealing with so we can
* set them back
*/
@@ -1631,17 +1625,7 @@ static int et131x_mdio_write(struct mii_bus *bus, int phy_addr,
struct net_device *netdev = bus->priv;
struct et131x_adapter *adapter = netdev_priv(netdev);
- return et131x_mii_write(adapter, reg, value);
-}
-
-static int et131x_mdio_reset(struct mii_bus *bus)
-{
- struct net_device *netdev = bus->priv;
- struct et131x_adapter *adapter = netdev_priv(netdev);
-
- et131x_mii_write(adapter, MII_BMCR, BMCR_RESET);
-
- return 0;
+ return et131x_mii_write(adapter, phy_addr, reg, value);
}
/* et1310_phy_power_switch - PHY power control
@@ -1656,18 +1640,20 @@ static int et131x_mdio_reset(struct mii_bus *bus)
static void et1310_phy_power_switch(struct et131x_adapter *adapter, bool down)
{
u16 data;
+ struct phy_device *phydev = adapter->phydev;
et131x_mii_read(adapter, MII_BMCR, &data);
data &= ~BMCR_PDOWN;
if (down)
data |= BMCR_PDOWN;
- et131x_mii_write(adapter, MII_BMCR, data);
+ et131x_mii_write(adapter, phydev->addr, MII_BMCR, data);
}
/* et131x_xcvr_init - Init the phy if we are setting it into force mode */
static void et131x_xcvr_init(struct et131x_adapter *adapter)
{
u16 lcr2;
+ struct phy_device *phydev = adapter->phydev;
/* Set the LED behavior such that LED 1 indicates speed (off =
* 10Mbits, blink = 100Mbits, on = 1000Mbits) and LED 2 indicates
@@ -1688,7 +1674,7 @@ static void et131x_xcvr_init(struct et131x_adapter *adapter)
else
lcr2 |= (LED_VAL_LINKON << LED_TXRX_SHIFT);
- et131x_mii_write(adapter, PHY_LED_2, lcr2);
+ et131x_mii_write(adapter, phydev->addr, PHY_LED_2, lcr2);
}
}
@@ -3643,14 +3629,14 @@ static void et131x_adjust_link(struct net_device *netdev)
et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18 | 0x4);
+ et131x_mii_write(adapter, phydev->addr, PHY_INDEX_REG,
register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
+ et131x_mii_write(adapter, phydev->addr, PHY_DATA_REG,
register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18);
}
et1310_config_flow_control(adapter);
@@ -3662,7 +3648,8 @@ static void et131x_adjust_link(struct net_device *netdev)
et131x_mii_read(adapter, PHY_CONFIG, ®);
reg &= ~ET_PHY_CONFIG_TX_FIFO_DEPTH;
reg |= ET_PHY_CONFIG_FIFO_DEPTH_32;
- et131x_mii_write(adapter, PHY_CONFIG, reg);
+ et131x_mii_write(adapter, phydev->addr, PHY_CONFIG,
+ reg);
}
et131x_set_rx_dma_timer(adapter);
@@ -3675,14 +3662,14 @@ static void et131x_adjust_link(struct net_device *netdev)
et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
- register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
- register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18 | 0x4);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_INDEX_REG, register18 | 0x8402);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_DATA_REG, register18 | 511);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18);
}
/* Free the packets being actively sent & stopped */
@@ -4644,10 +4631,6 @@ static int et131x_pci_setup(struct pci_dev *pdev,
/* Copy address into the net_device struct */
memcpy(netdev->dev_addr, adapter->addr, ETH_ALEN);
- /* Init variable for counting how long we do not have link status */
- adapter->boot_coma = 0;
- et1310_disable_phy_coma(adapter);
-
rc = -ENOMEM;
/* Setup the mii_bus struct */
@@ -4663,7 +4646,6 @@ static int et131x_pci_setup(struct pci_dev *pdev,
adapter->mii_bus->priv = netdev;
adapter->mii_bus->read = et131x_mdio_read;
adapter->mii_bus->write = et131x_mdio_write;
- adapter->mii_bus->reset = et131x_mdio_reset;
adapter->mii_bus->irq = kmalloc_array(PHY_MAX_ADDR, sizeof(int),
GFP_KERNEL);
if (!adapter->mii_bus->irq)
@@ -4687,6 +4669,10 @@ static int et131x_pci_setup(struct pci_dev *pdev,
/* Setup et1310 as per the documentation */
et131x_adapter_setup(adapter);
+ /* Init variable for counting how long we do not have link status */
+ adapter->boot_coma = 0;
+ et1310_disable_phy_coma(adapter);
+
/* We can enable interrupts now
*
* NOTE - Because registration of interrupt handler is done in the
--
2.0.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] staging: et131x: Fix errors caused by phydev->addr accesses before initialisation
2014-08-05 22:57 [PATCH] staging: et131x: Fix errors caused by phydev->addr accesses before initialisation Mark Einon
@ 2014-08-10 4:39 ` Greg KH
0 siblings, 0 replies; 3+ messages in thread
From: Greg KH @ 2014-08-10 4:39 UTC (permalink / raw)
To: Mark Einon; +Cc: devel, linux-kernel, netdev, stable
On Tue, Aug 05, 2014 at 11:57:06PM +0100, Mark Einon wrote:
> Fix two reported bugs, caused by et131x_adapter->phydev->addr being accessed
> before it is initialised, by:
>
> - letting et131x_mii_write() take a phydev address, instead of using the one
> stored in adapter by default. This is so et131x_mdio_write() can use it's own
> addr value.
> - removing implementation of et131x_mdio_reset(), as it's not needed.
> - moving a call to et131x_disable_phy_coma() in et131x_pci_setup(), which uses
> phydev->addr, until after the mdiobus has been registered.
>
> Link: https://bugzilla.kernel.org/show_bug.cgi?id=80751
> Link: https://bugzilla.kernel.org/show_bug.cgi?id=77121
> Cc: stable@vger.kernel.org
> Signed-off-by: Mark Einon <mark.einon@gmail.com>
> ---
> drivers/staging/et131x/et131x.c | 68 ++++++++++++++++-------------------------
> 1 file changed, 27 insertions(+), 41 deletions(-)
I got 3 copies of this patch, all look to be different?
I don't know what to do, so I've deleted them all, please resend the
version you want me to apply.
thanks,
greg k-h
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] staging: et131x: Fix errors caused by phydev->addr accesses before initialisation
@ 2014-08-10 4:39 ` Greg KH
0 siblings, 0 replies; 3+ messages in thread
From: Greg KH @ 2014-08-10 4:39 UTC (permalink / raw)
To: Mark Einon; +Cc: devel, netdev, linux-kernel, stable
On Tue, Aug 05, 2014 at 11:57:06PM +0100, Mark Einon wrote:
> Fix two reported bugs, caused by et131x_adapter->phydev->addr being accessed
> before it is initialised, by:
>
> - letting et131x_mii_write() take a phydev address, instead of using the one
> stored in adapter by default. This is so et131x_mdio_write() can use it's own
> addr value.
> - removing implementation of et131x_mdio_reset(), as it's not needed.
> - moving a call to et131x_disable_phy_coma() in et131x_pci_setup(), which uses
> phydev->addr, until after the mdiobus has been registered.
>
> Link: https://bugzilla.kernel.org/show_bug.cgi?id=80751
> Link: https://bugzilla.kernel.org/show_bug.cgi?id=77121
> Cc: stable@vger.kernel.org
> Signed-off-by: Mark Einon <mark.einon@gmail.com>
> ---
> drivers/staging/et131x/et131x.c | 68 ++++++++++++++++-------------------------
> 1 file changed, 27 insertions(+), 41 deletions(-)
I got 3 copies of this patch, all look to be different?
I don't know what to do, so I've deleted them all, please resend the
version you want me to apply.
thanks,
greg k-h
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-08-10 12:11 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-08-05 22:57 [PATCH] staging: et131x: Fix errors caused by phydev->addr accesses before initialisation Mark Einon
2014-08-10 4:39 ` Greg KH
2014-08-10 4:39 ` Greg KH
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.