From: Roger Quadros <rogerq@ti.com> To: <balbi@ti.com>, <tony@atomide.com>, <myungjoo.ham@samsung.com>, <cw00.choi@samsung.com> Cc: <george.cherian@ti.com>, <nsekhar@ti.com>, <devicetree@vger.kernel.org>, <linux-usb@vger.kernel.org>, <linux-omap@vger.kernel.org>, <linux-kernel@vger.kernel.org>, Roger Quadros <rogerq@ti.com> Subject: [PATCH 4/5] ARM: dts: dra72-evm: Add extcon nodes for USB Date: Mon, 19 Jan 2015 19:52:21 +0200 [thread overview] Message-ID: <1421689942-10201-5-git-send-email-rogerq@ti.com> (raw) In-Reply-To: <1421689942-10201-1-git-send-email-rogerq@ti.com> On this EVM, the USB cable state has to be determined via the ID pin tied to a GPIO line. We use the gpio-usb-extcon driver to read the ID pin and the extcon framework to forward the USB cable state information to the USB driver so the controller can be configured in the right mode (host/peripheral). Gets USB peripheral mode to work on this EVM. Signed-off-by: Roger Quadros <rogerq@ti.com> --- arch/arm/boot/dts/dra72-evm.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 89085d0..d93a98f 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "dra72x.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "TI DRA722"; @@ -24,6 +25,16 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb"; + id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; + }; + + extcon_usb2: extcon_usb2 { + compatible = "linux,extcon-usb"; + id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; + }; }; &dra7_pmx_core { @@ -243,6 +254,18 @@ ti,palmas-long-press-seconds = <6>; }; }; + + pcf_gpio_21: gpio@21 { + compatible = "ti,pcf8575"; + reg = <0x21>; + lines-initial-states = <0x1408>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; &uart1 { @@ -345,6 +368,14 @@ phy-supply = <&ldo4_reg>; }; +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; -- 2.1.0
WARNING: multiple messages have this Message-ID (diff)
From: Roger Quadros <rogerq@ti.com> To: balbi@ti.com, tony@atomide.com, myungjoo.ham@samsung.com, cw00.choi@samsung.com Cc: george.cherian@ti.com, nsekhar@ti.com, devicetree@vger.kernel.org, linux-usb@vger.kernel.org, linux-omap@vger.kernel.org, linux-kernel@vger.kernel.org, Roger Quadros <rogerq@ti.com> Subject: [PATCH 4/5] ARM: dts: dra72-evm: Add extcon nodes for USB Date: Mon, 19 Jan 2015 19:52:21 +0200 [thread overview] Message-ID: <1421689942-10201-5-git-send-email-rogerq@ti.com> (raw) In-Reply-To: <1421689942-10201-1-git-send-email-rogerq@ti.com> On this EVM, the USB cable state has to be determined via the ID pin tied to a GPIO line. We use the gpio-usb-extcon driver to read the ID pin and the extcon framework to forward the USB cable state information to the USB driver so the controller can be configured in the right mode (host/peripheral). Gets USB peripheral mode to work on this EVM. Signed-off-by: Roger Quadros <rogerq@ti.com> --- arch/arm/boot/dts/dra72-evm.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 89085d0..d93a98f 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "dra72x.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "TI DRA722"; @@ -24,6 +25,16 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb"; + id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; + }; + + extcon_usb2: extcon_usb2 { + compatible = "linux,extcon-usb"; + id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; + }; }; &dra7_pmx_core { @@ -243,6 +254,18 @@ ti,palmas-long-press-seconds = <6>; }; }; + + pcf_gpio_21: gpio@21 { + compatible = "ti,pcf8575"; + reg = <0x21>; + lines-initial-states = <0x1408>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; &uart1 { @@ -345,6 +368,14 @@ phy-supply = <&ldo4_reg>; }; +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; -- 2.1.0
next prev parent reply other threads:[~2015-01-19 17:52 UTC|newest] Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-01-19 17:52 [PATCH 0/5] extcon: usb: Introduce USB GPIO extcon driver. Fix DRA7 USB Roger Quadros 2015-01-19 17:52 ` Roger Quadros 2015-01-19 17:52 ` [PATCH 1/5] extcon: gpio-usb: Introduce gpio usb extcon driver Roger Quadros 2015-01-19 17:52 ` Roger Quadros 2015-01-20 19:00 ` Felipe Balbi 2015-01-20 19:00 ` Felipe Balbi 2015-01-21 5:28 ` Chanwoo Choi 2015-01-21 5:28 ` Chanwoo Choi 2015-01-22 13:27 ` Roger Quadros 2015-01-22 13:27 ` Roger Quadros 2015-01-19 17:52 ` [PATCH 2/5] usb: extcon: Fix USB-Host cable name Roger Quadros 2015-01-19 17:52 ` Roger Quadros 2015-01-20 19:01 ` Felipe Balbi 2015-01-20 19:01 ` Felipe Balbi 2015-01-19 17:52 ` [PATCH 3/5] ARM: dts: dra7-evm: Add extcon nodes for USB Roger Quadros 2015-01-19 17:52 ` Roger Quadros 2015-01-20 19:02 ` Felipe Balbi 2015-01-20 19:02 ` Felipe Balbi 2015-01-19 17:52 ` Roger Quadros [this message] 2015-01-19 17:52 ` [PATCH 4/5] ARM: dts: dra72-evm: " Roger Quadros 2015-01-20 19:02 ` Felipe Balbi 2015-01-20 19:02 ` Felipe Balbi 2015-01-19 17:52 ` [PATCH 5/5] ARM: omap2plus_defconfig: Enable PCF857X and EXTCON_GPIO_USB Roger Quadros 2015-01-19 17:52 ` Roger Quadros 2015-01-19 18:45 ` Tony Lindgren 2015-01-19 19:38 ` Tony Lindgren 2015-01-20 9:26 ` Roger Quadros 2015-01-20 9:26 ` Roger Quadros 2015-01-20 19:02 ` [PATCH 0/5] extcon: usb: Introduce USB GPIO extcon driver. Fix DRA7 USB Felipe Balbi 2015-01-20 19:02 ` Felipe Balbi 2015-01-22 13:32 ` Roger Quadros 2015-01-22 13:32 ` Roger Quadros 2015-01-22 14:57 ` Roger Quadros 2015-01-22 14:57 ` Roger Quadros 2015-01-22 20:29 ` Felipe Balbi 2015-01-22 20:29 ` Felipe Balbi 2015-01-23 7:26 ` Roger Quadros 2015-01-23 7:26 ` Roger Quadros 2015-01-23 16:19 ` Felipe Balbi 2015-01-23 16:19 ` Felipe Balbi
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1421689942-10201-5-git-send-email-rogerq@ti.com \ --to=rogerq@ti.com \ --cc=balbi@ti.com \ --cc=cw00.choi@samsung.com \ --cc=devicetree@vger.kernel.org \ --cc=george.cherian@ti.com \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=linux-usb@vger.kernel.org \ --cc=myungjoo.ham@samsung.com \ --cc=nsekhar@ti.com \ --cc=tony@atomide.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.