[PATCH 00/13] ARM: dts: omap3-gta04: Various DT fixes

[PATCH 00/13] ARM: dts: omap3-gta04: Various DT fixes

[Marek Belisko]

This series contains fixes for gta04 devicetree. I collected patches
from H. Nikolaus Schaller + NeilBrown and myself. Patches contains mostly fixes
+ adding new nodes and comments. All changes tested on gta04a4 board.

H. Nikolaus Schaller (5):
  ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
  ARM: dts: omap3-gta04: Fix audio node malformatting
  ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
  ARM: dts: omap3-gta04: Enable twl audio vibra support
  ARM: dts: omap3-gta04: Enable power-off using twl4030

Marek Belisko (2):
  ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
  ARM: dts: omap3-gta04: Add ramp value for twl4030 audio

NeilBrown (6):
  ARM: dts: omap3-gta04: add comments about gpios
  ARM: dts: omap3-gta04: enable power-off for wifi card.
  ARM: dts: omap3-gta04: add gyroscope
  ARM: dts: omap3-gta04: only power DSS when necessary.
  ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"
  ARM: dts: omap3-gta04: Disable keypad

 arch/arm/boot/dts/omap3-gta04.dtsi | 54 +++++++++++++++++++++++++++-----------
 1 file changed, 39 insertions(+), 15 deletions(-)

-- 
1.9.1

[PATCH 00/13] ARM: dts: omap3-gta04: Various DT fixes

[Marek Belisko]

This series contains fixes for gta04 devicetree. I collected patches
from H. Nikolaus Schaller + NeilBrown and myself. Patches contains mostly fixes
+ adding new nodes and comments. All changes tested on gta04a4 board.

H. Nikolaus Schaller (5):
  ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
  ARM: dts: omap3-gta04: Fix audio node malformatting
  ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
  ARM: dts: omap3-gta04: Enable twl audio vibra support
  ARM: dts: omap3-gta04: Enable power-off using twl4030

Marek Belisko (2):
  ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
  ARM: dts: omap3-gta04: Add ramp value for twl4030 audio

NeilBrown (6):
  ARM: dts: omap3-gta04: add comments about gpios
  ARM: dts: omap3-gta04: enable power-off for wifi card.
  ARM: dts: omap3-gta04: add gyroscope
  ARM: dts: omap3-gta04: only power DSS when necessary.
  ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"
  ARM: dts: omap3-gta04: Disable keypad

 arch/arm/boot/dts/omap3-gta04.dtsi | 54 +++++++++++++++++++++++++++-----------
 1 file changed, 39 insertions(+), 15 deletions(-)

-- 
1.9.1

[PATCH 00/13] ARM: dts: omap3-gta04: Various DT fixes

[Marek Belisko]

This series contains fixes for gta04 devicetree. I collected patches
from H. Nikolaus Schaller + NeilBrown and myself. Patches contains mostly fixes
+ adding new nodes and comments. All changes tested on gta04a4 board.

H. Nikolaus Schaller (5):
  ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
  ARM: dts: omap3-gta04: Fix audio node malformatting
  ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
  ARM: dts: omap3-gta04: Enable twl audio vibra support
  ARM: dts: omap3-gta04: Enable power-off using twl4030

Marek Belisko (2):
  ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
  ARM: dts: omap3-gta04: Add ramp value for twl4030 audio

NeilBrown (6):
  ARM: dts: omap3-gta04: add comments about gpios
  ARM: dts: omap3-gta04: enable power-off for wifi card.
  ARM: dts: omap3-gta04: add gyroscope
  ARM: dts: omap3-gta04: only power DSS when necessary.
  ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"
  ARM: dts: omap3-gta04: Disable keypad

 arch/arm/boot/dts/omap3-gta04.dtsi | 54 +++++++++++++++++++++++++++-----------
 1 file changed, 39 insertions(+), 15 deletions(-)

-- 
1.9.1

[PATCH 01/13] ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Fix attribute names.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 655d6e9..fa39232 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -342,8 +342,8 @@
 };
 
 &charger {
-	bb_uvolt = <3200000>;
-	bb_uamp = <150>;
+	ti,bb-uvolt = <3200000>;
+	ti,bb-uamp = <150>;
 };
 
 /* spare */
-- 
1.9.1

[PATCH 01/13] ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Fix attribute names.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 655d6e9..fa39232 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -342,8 +342,8 @@
 };
 
 &charger {
-	bb_uvolt = <3200000>;
-	bb_uamp = <150>;
+	ti,bb-uvolt = <3200000>;
+	ti,bb-uamp = <150>;
 };
 
 /* spare */
-- 
1.9.1

[PATCH 02/13] ARM: dts: omap3-gta04: Fix audio node malformatting

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Audio should be child of twl node.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index fa39232..c78380e 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -202,11 +202,11 @@
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
-	};
 
-	twl_audio: audio {
-		compatible = "ti,twl4030-audio";
-		codec {
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
 		};
 	};
 };
-- 
1.9.1

[PATCH 02/13] ARM: dts: omap3-gta04: Fix audio node malformatting

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Audio should be child of twl node.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index fa39232..c78380e 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -202,11 +202,11 @@
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
-	};
 
-	twl_audio: audio {
-		compatible = "ti,twl4030-audio";
-		codec {
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
 		};
 	};
 };
-- 
1.9.1

[PATCH 02/13] ARM: dts: omap3-gta04: Fix audio node malformatting

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Audio should be child of twl node.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index fa39232..c78380e 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -202,11 +202,11 @@
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
-	};
 
-	twl_audio: audio {
-		compatible = "ti,twl4030-audio";
-		codec {
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
 		};
 	};
 };
-- 
1.9.1

[PATCH 03/13] ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index c78380e..7272591 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -449,3 +449,7 @@
 		};
 	};
 };
+
+&mcbsp2 {
+	status = "okay";
+};
-- 
1.9.1

[PATCH 03/13] ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index c78380e..7272591 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -449,3 +449,7 @@
 		};
 	};
 };
+
+&mcbsp2 {
+	status = "okay";
+};
-- 
1.9.1

[PATCH 03/13] ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index c78380e..7272591 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -449,3 +449,7 @@
 		};
 	};
 };
+
+&mcbsp2 {
+	status = "okay";
+};
-- 
1.9.1

[PATCH 04/13] ARM: dts: omap3-gta04: Enable twl audio vibra support

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 7272591..fd6ac80 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -205,6 +205,7 @@
 
 		twl_audio: audio {
 			compatible = "ti,twl4030-audio";
+			ti,enable-vibra = <1>;
 			codec {
 			};
 		};
-- 
1.9.1

[PATCH 04/13] ARM: dts: omap3-gta04: Enable twl audio vibra support

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 7272591..fd6ac80 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -205,6 +205,7 @@
 
 		twl_audio: audio {
 			compatible = "ti,twl4030-audio";
+			ti,enable-vibra = <1>;
 			codec {
 			};
 		};
-- 
1.9.1

[PATCH 05/13] ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node

[Marek Belisko]

GPIO_115 used as irq is in &gpio4, not &gpio3.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index fd6ac80..0265474 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -230,7 +230,7 @@
 	bma180@41 {
 		compatible = "bosch,bma180";
 		reg = <0x41>;
-		interrupt-parent = <&gpio3>;
+		interrupt-parent = <&gpio4>;
 		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-- 
1.9.1

[PATCH 05/13] ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node

[Marek Belisko]

GPIO_115 used as irq is in &gpio4, not &gpio3.

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index fd6ac80..0265474 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -230,7 +230,7 @@
 	bma180 at 41 {
 		compatible = "bosch,bma180";
 		reg = <0x41>;
-		interrupt-parent = <&gpio3>;
+		interrupt-parent = <&gpio4>;
 		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-- 
1.9.1

[PATCH 06/13] ARM: dts: omap3-gta04: Enable power-off using twl4030

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Enabled poweroff through PMIC on GTA04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 0265474..b56c85b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -209,6 +209,11 @@
 			codec {
 			};
 		};
+
+		twl_power: power {
+			compatible = "ti,twl4030-power";
+			ti,use_poweroff;
+		};
 	};
 };
 
-- 
1.9.1

[PATCH 06/13] ARM: dts: omap3-gta04: Enable power-off using twl4030

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Enabled poweroff through PMIC on GTA04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 0265474..b56c85b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -209,6 +209,11 @@
 			codec {
 			};
 		};
+
+		twl_power: power {
+			compatible = "ti,twl4030-power";
+			ti,use_poweroff;
+		};
 	};
 };
 
-- 
1.9.1

[PATCH 06/13] ARM: dts: omap3-gta04: Enable power-off using twl4030

[Marek Belisko]

From: "H. Nikolaus Schaller" <hns@goldelico.com>

Enabled poweroff through PMIC on GTA04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 0265474..b56c85b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -209,6 +209,11 @@
 			codec {
 			};
 		};
+
+		twl_power: power {
+			compatible = "ti,twl4030-power";
+			ti,use_poweroff;
+		};
 	};
 };
 
-- 
1.9.1

Re: [PATCH 06/13] ARM: dts: omap3-gta04: Enable power-off using twl4030

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [150122 12:42]:
> From: "H. Nikolaus Schaller" <hns@goldelico.com>
> 
> Enabled poweroff through PMIC on GTA04.
> 
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> ---
>  arch/arm/boot/dts/omap3-gta04.dtsi | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> index 0265474..b56c85b 100644
> --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> @@ -209,6 +209,11 @@
>  			codec {
>  			};
>  		};
> +
> +		twl_power: power {
> +			compatible = "ti,twl4030-power";
> +			ti,use_poweroff;
> +		};
>  	};
>  };
>  

No need to change this patch, but you may want to get things working
with ti,twl4030-power-idle-osc-off for PM if you're running it on
batteries :)

Regards,

Tony

[PATCH 06/13] ARM: dts: omap3-gta04: Enable power-off using twl4030

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [150122 12:42]:
> From: "H. Nikolaus Schaller" <hns@goldelico.com>
> 
> Enabled poweroff through PMIC on GTA04.
> 
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> ---
>  arch/arm/boot/dts/omap3-gta04.dtsi | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> index 0265474..b56c85b 100644
> --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> @@ -209,6 +209,11 @@
>  			codec {
>  			};
>  		};
> +
> +		twl_power: power {
> +			compatible = "ti,twl4030-power";
> +			ti,use_poweroff;
> +		};
>  	};
>  };
>  

No need to change this patch, but you may want to get things working
with ti,twl4030-power-idle-osc-off for PM if you're running it on
batteries :)

Regards,

Tony

[PATCH 07/13] ARM: dts: omap3-gta04: Add ramp value for twl4030 audio

[Marek Belisko]

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index b56c85b..6f5fcbb 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -207,6 +207,7 @@
 			compatible = "ti,twl4030-audio";
 			ti,enable-vibra = <1>;
 			codec {
+				ti,ramp_delay_value = <3>;
 			};
 		};
 
-- 
1.9.1

[PATCH 07/13] ARM: dts: omap3-gta04: Add ramp value for twl4030 audio

[Marek Belisko]

Signed-off-by: Marek Belisko <marek@goldelico.com>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index b56c85b..6f5fcbb 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -207,6 +207,7 @@
 			compatible = "ti,twl4030-audio";
 			ti,enable-vibra = <1>;
 			codec {
+				ti,ramp_delay_value = <3>;
 			};
 		};
 
-- 
1.9.1

[PATCH 08/13] ARM: dts: omap3-gta04: add comments about gpios

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Add comments to state which GPIO is used for some interrupts.

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 6f5fcbb..b65b5ed 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -229,7 +229,7 @@
 		compatible = "bosch,bmp085";
 		reg = <0x77>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* GPIO_113 */
 	};
 
 	/* accelerometer */
@@ -237,7 +237,7 @@
 		compatible = "bosch,bma180";
 		reg = <0x41>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
 
 	/* leds */
@@ -288,7 +288,7 @@
 		compatible = "ti,tsc2007";
 		reg = <0x48>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>; /* GPIO_160 */
 		gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
 		ti,x-plate-ohms = <600>;
 	};
-- 
1.9.1

[PATCH 08/13] ARM: dts: omap3-gta04: add comments about gpios

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Add comments to state which GPIO is used for some interrupts.

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 6f5fcbb..b65b5ed 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -229,7 +229,7 @@
 		compatible = "bosch,bmp085";
 		reg = <0x77>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* GPIO_113 */
 	};
 
 	/* accelerometer */
@@ -237,7 +237,7 @@
 		compatible = "bosch,bma180";
 		reg = <0x41>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
 
 	/* leds */
@@ -288,7 +288,7 @@
 		compatible = "ti,tsc2007";
 		reg = <0x48>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>; /* GPIO_160 */
 		gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
 		ti,x-plate-ohms = <600>;
 	};
-- 
1.9.1

[PATCH 08/13] ARM: dts: omap3-gta04: add comments about gpios

[Marek Belisko]

From: NeilBrown <neil-+NVA1uvv1dVBDLzU/O5InQ@public.gmane.org>

Add comments to state which GPIO is used for some interrupts.

Signed-off-by: NeilBrown <neil-+NVA1uvv1dVBDLzU/O5InQ@public.gmane.org>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 6f5fcbb..b65b5ed 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -229,7 +229,7 @@
 		compatible = "bosch,bmp085";
 		reg = <0x77>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* GPIO_113 */
 	};
 
 	/* accelerometer */
@@ -237,7 +237,7 @@
 		compatible = "bosch,bma180";
 		reg = <0x41>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
 
 	/* leds */
@@ -288,7 +288,7 @@
 		compatible = "ti,tsc2007";
 		reg = <0x48>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>; /* GPIO_160 */
 		gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
 		ti,x-plate-ohms = <600>;
 	};
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 09/13] ARM: dts: omap3-gta04: enable power-off for wifi card.

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index b65b5ed..ab5dd98 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -327,6 +327,7 @@
 	vmmc-supply = <&vaux4>;
 	bus-width = <4>;
 	ti,non-removable;
+	cap-power-off-card;
 };
 
 &mmc3 {
-- 
1.9.1

[PATCH 09/13] ARM: dts: omap3-gta04: enable power-off for wifi card.

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index b65b5ed..ab5dd98 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -327,6 +327,7 @@
 	vmmc-supply = <&vaux4>;
 	bus-width = <4>;
 	ti,non-removable;
+	cap-power-off-card;
 };
 
 &mmc3 {
-- 
1.9.1

[PATCH 10/13] ARM: dts: omap3-gta04: add gyroscope

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index ab5dd98..08f0b25 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -240,6 +240,14 @@
 		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
 
+	/* gyroscope */
+	itg3200@68 {
+		compatible = "invensense,itg3200";
+		reg = <0x68>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <24 0>; /* GPIO_56 */
+	};
+
 	/* leds */
 	tca6507@45 {
 		compatible = "ti,tca6507";
-- 
1.9.1

[PATCH 10/13] ARM: dts: omap3-gta04: add gyroscope

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index ab5dd98..08f0b25 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -240,6 +240,14 @@
 		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
 
+	/* gyroscope */
+	itg3200 at 68 {
+		compatible = "invensense,itg3200";
+		reg = <0x68>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <24 0>; /* GPIO_56 */
+	};
+
 	/* leds */
 	tca6507 at 45 {
 		compatible = "ti,tca6507";
-- 
1.9.1

[PATCH 11/13] ARM: dts: omap3-gta04: only power DSS when necessary.

[Marek Belisko]

From: NeilBrown <neil@brown.name>

i.e. configure vpll2 as a supply for the dss rather
than being always-on.

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 08f0b25..228e79b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -393,16 +393,12 @@
 	regulator-max-microvolt = <3150000>;
 };
 
-/* Needed to power the DPI pins */
-&vpll2 {
-	regulator-always-on;
-};
-
 &dss {
 	pinctrl-names = "default";
 	pinctrl-0 = < &dss_dpi_pins >;
 
 	status = "okay";
+	vdds_dsi-supply = <&vpll2>;
 
 	port {
 		dpi_out: endpoint {
-- 
1.9.1

[PATCH 11/13] ARM: dts: omap3-gta04: only power DSS when necessary.

[Marek Belisko]

From: NeilBrown <neil@brown.name>

i.e. configure vpll2 as a supply for the dss rather
than being always-on.

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 08f0b25..228e79b 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -393,16 +393,12 @@
 	regulator-max-microvolt = <3150000>;
 };
 
-/* Needed to power the DPI pins */
-&vpll2 {
-	regulator-always-on;
-};
-
 &dss {
 	pinctrl-names = "default";
 	pinctrl-0 = < &dss_dpi_pins >;
 
 	status = "okay";
+	vdds_dsi-supply = <&vpll2>;
 
 	port {
 		dpi_out: endpoint {
-- 
1.9.1

[PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 228e79b..8d2b0a1 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -357,6 +357,10 @@
 	pinctrl-0 = <&uart3_pins>;
 };
 
+&uart4 {
+	status = "disabled";
+};
+
 &charger {
 	ti,bb-uvolt = <3200000>;
 	ti,bb-uamp = <150>;
-- 
1.9.1

[PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[Marek Belisko]

From: NeilBrown <neil@brown.name>

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 228e79b..8d2b0a1 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -357,6 +357,10 @@
 	pinctrl-0 = <&uart3_pins>;
 };
 
+&uart4 {
+	status = "disabled";
+};
+
 &charger {
 	ti,bb-uvolt = <3200000>;
 	ti,bb-uamp = <150>;
-- 
1.9.1

Re: [PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [150122 12:42]:
> From: NeilBrown <neil@brown.name>
> 
> Signed-off-by: NeilBrown <neil@brown.name>
> ---
>  arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> index 228e79b..8d2b0a1 100644
> --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> @@ -357,6 +357,10 @@
>  	pinctrl-0 = <&uart3_pins>;
>  };
>  
> +&uart4 {
> +	status = "disabled";
> +};
> +

This you probably want to avoid from PM point of view. Depending on
bootloader state of uart4, Linux may or may not be able to hit any
deeper power states.

Marking something with status = "disabled" in dts causes the device
entry not even to be created. That means hwmod won't be able to reset
and idle this device during boot.

The uart4 device is there for sure even if not muxed and in incomplete
state. You may want to also check other places where you're using
status = "disabled" for the same reasons.

Regards,

Tony

[PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [150122 12:42]:
> From: NeilBrown <neil@brown.name>
> 
> Signed-off-by: NeilBrown <neil@brown.name>
> ---
>  arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> index 228e79b..8d2b0a1 100644
> --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> @@ -357,6 +357,10 @@
>  	pinctrl-0 = <&uart3_pins>;
>  };
>  
> +&uart4 {
> +	status = "disabled";
> +};
> +

This you probably want to avoid from PM point of view. Depending on
bootloader state of uart4, Linux may or may not be able to hit any
deeper power states.

Marking something with status = "disabled" in dts causes the device
entry not even to be created. That means hwmod won't be able to reset
and idle this device during boot.

The uart4 device is there for sure even if not muxed and in incomplete
state. You may want to also check other places where you're using
status = "disabled" for the same reasons.

Regards,

Tony

Re: [PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[NeilBrown]

[-- Attachment #1: Type: text/plain, Size: 2422 bytes --]

On Thu, 22 Jan 2015 13:40:53 -0800 Tony Lindgren <tony@atomide.com> wrote:

> * Marek Belisko <marek@goldelico.com> [150122 12:42]:
> > From: NeilBrown <neil@brown.name>
> > 
> > Signed-off-by: NeilBrown <neil@brown.name>
> > ---
> >  arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
> >  1 file changed, 4 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> > index 228e79b..8d2b0a1 100644
> > --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> > +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> > @@ -357,6 +357,10 @@
> >  	pinctrl-0 = <&uart3_pins>;
> >  };
> >  
> > +&uart4 {
> > +	status = "disabled";
> > +};
> > +
> 
> This you probably want to avoid from PM point of view. Depending on
> bootloader state of uart4, Linux may or may not be able to hit any
> deeper power states.
> 
> Marking something with status = "disabled" in dts causes the device
> entry not even to be created. That means hwmod won't be able to reset
> and idle this device during boot.
> 
> The uart4 device is there for sure even if not muxed and in incomplete
> state. You may want to also check other places where you're using
> status = "disabled" for the same reasons.

That's ... unfortunate.  Would that apply to the MCBSPs too?  They are
disabled by default so you would need to explicitly enable them all for
sensible behaviour....

Hopefully there is some way to mark as device as "this is not used, make sure
it is turned off and stays off" ???

Thanks for the heads-up.  I'll have a look and see exactly what is happening.

BTW, on the topic of OMAP UARTs and power saving...
 I note that there are now two drivers for the OMAP3 UART - omap-serial and
 8250_omap.
 I also note that your commit:

commit a2fc36613ac1af2e92cbed7af80bc72d8114dd50
    ARM: OMAP3: Use manual idle for UARTs because of DMA errata

 is incompatible with omap-serial.  In particular, if I enable runtime
 suspend of the serial port by setting the autosuspend_timeout, then incoming
 characters will no longer wake the port (if I revert your patch incoming
 chars do wake the port).
 This could (I think) be fixed by enabling the RX/CTS interrupt.  However if
 omap-serial is being deprecated, then there probably isn't any point.

 So: what is the longer term expectation for these drivers?  Should we be
 switching over to 8250?

Thanks,
NeilBrown

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 811 bytes --]

[PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[NeilBrown]

On Thu, 22 Jan 2015 13:40:53 -0800 Tony Lindgren <tony@atomide.com> wrote:

> * Marek Belisko <marek@goldelico.com> [150122 12:42]:
> > From: NeilBrown <neil@brown.name>
> > 
> > Signed-off-by: NeilBrown <neil@brown.name>
> > ---
> >  arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
> >  1 file changed, 4 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> > index 228e79b..8d2b0a1 100644
> > --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> > +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> > @@ -357,6 +357,10 @@
> >  	pinctrl-0 = <&uart3_pins>;
> >  };
> >  
> > +&uart4 {
> > +	status = "disabled";
> > +};
> > +
> 
> This you probably want to avoid from PM point of view. Depending on
> bootloader state of uart4, Linux may or may not be able to hit any
> deeper power states.
> 
> Marking something with status = "disabled" in dts causes the device
> entry not even to be created. That means hwmod won't be able to reset
> and idle this device during boot.
> 
> The uart4 device is there for sure even if not muxed and in incomplete
> state. You may want to also check other places where you're using
> status = "disabled" for the same reasons.

That's ... unfortunate.  Would that apply to the MCBSPs too?  They are
disabled by default so you would need to explicitly enable them all for
sensible behaviour....

Hopefully there is some way to mark as device as "this is not used, make sure
it is turned off and stays off" ???

Thanks for the heads-up.  I'll have a look and see exactly what is happening.

BTW, on the topic of OMAP UARTs and power saving...
 I note that there are now two drivers for the OMAP3 UART - omap-serial and
 8250_omap.
 I also note that your commit:

commit a2fc36613ac1af2e92cbed7af80bc72d8114dd50
    ARM: OMAP3: Use manual idle for UARTs because of DMA errata

 is incompatible with omap-serial.  In particular, if I enable runtime
 suspend of the serial port by setting the autosuspend_timeout, then incoming
 characters will no longer wake the port (if I revert your patch incoming
 chars do wake the port).
 This could (I think) be fixed by enabling the RX/CTS interrupt.  However if
 omap-serial is being deprecated, then there probably isn't any point.

 So: what is the longer term expectation for these drivers?  Should we be
 switching over to 8250?

Thanks,
NeilBrown
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 811 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150124/ad6c075c/attachment.sig>

Re: [PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[NeilBrown]

[-- Attachment #1: Type: text/plain, Size: 2534 bytes --]

On Thu, 22 Jan 2015 13:40:53 -0800 Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org> wrote:

> * Marek Belisko <marek-xXXSsgcRVICgSpxsJD1C4w@public.gmane.org> [150122 12:42]:
> > From: NeilBrown <neil-+NVA1uvv1dVBDLzU/O5InQ@public.gmane.org>
> > 
> > Signed-off-by: NeilBrown <neil-+NVA1uvv1dVBDLzU/O5InQ@public.gmane.org>
> > ---
> >  arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
> >  1 file changed, 4 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> > index 228e79b..8d2b0a1 100644
> > --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> > +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> > @@ -357,6 +357,10 @@
> >  	pinctrl-0 = <&uart3_pins>;
> >  };
> >  
> > +&uart4 {
> > +	status = "disabled";
> > +};
> > +
> 
> This you probably want to avoid from PM point of view. Depending on
> bootloader state of uart4, Linux may or may not be able to hit any
> deeper power states.
> 
> Marking something with status = "disabled" in dts causes the device
> entry not even to be created. That means hwmod won't be able to reset
> and idle this device during boot.
> 
> The uart4 device is there for sure even if not muxed and in incomplete
> state. You may want to also check other places where you're using
> status = "disabled" for the same reasons.

That's ... unfortunate.  Would that apply to the MCBSPs too?  They are
disabled by default so you would need to explicitly enable them all for
sensible behaviour....

Hopefully there is some way to mark as device as "this is not used, make sure
it is turned off and stays off" ???

Thanks for the heads-up.  I'll have a look and see exactly what is happening.

BTW, on the topic of OMAP UARTs and power saving...
 I note that there are now two drivers for the OMAP3 UART - omap-serial and
 8250_omap.
 I also note that your commit:

commit a2fc36613ac1af2e92cbed7af80bc72d8114dd50
    ARM: OMAP3: Use manual idle for UARTs because of DMA errata

 is incompatible with omap-serial.  In particular, if I enable runtime
 suspend of the serial port by setting the autosuspend_timeout, then incoming
 characters will no longer wake the port (if I revert your patch incoming
 chars do wake the port).
 This could (I think) be fixed by enabling the RX/CTS interrupt.  However if
 omap-serial is being deprecated, then there probably isn't any point.

 So: what is the longer term expectation for these drivers?  Should we be
 switching over to 8250?

Thanks,
NeilBrown

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 811 bytes --]

Re: [PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[Tony Lindgren]

* NeilBrown <neilb@suse.de> [150123 14:31]:
> On Thu, 22 Jan 2015 13:40:53 -0800 Tony Lindgren <tony@atomide.com> wrote:
> > >  
> > > +&uart4 {
> > > +	status = "disabled";
> > > +};
> > > +
> > 
> > This you probably want to avoid from PM point of view. Depending on
> > bootloader state of uart4, Linux may or may not be able to hit any
> > deeper power states.
> > 
> > Marking something with status = "disabled" in dts causes the device
> > entry not even to be created. That means hwmod won't be able to reset
> > and idle this device during boot.
> > 
> > The uart4 device is there for sure even if not muxed and in incomplete
> > state. You may want to also check other places where you're using
> > status = "disabled" for the same reasons.
> 
> That's ... unfortunate.  Would that apply to the MCBSPs too?  They are
> disabled by default so you would need to explicitly enable them all for
> sensible behaviour....

Yeah that applies to all the SoC integrated devices that the bus code
(hwmod) is supposed to reset and idle if unused. Basically anything
that depends on the dev entry being created.
 
> Hopefully there is some way to mark as device as "this is not used, make sure
> it is turned off and stays off" ???

Not currently that I know of :) To do that, we should add something
like status = "incomplete" where the dev entry gets created but the
driver is never probed. And incomplete here meaning that the device
is missing some parts like pins that would make it work properly.
 
> Thanks for the heads-up.  I'll have a look and see exactly what is happening.

OK
 
> BTW, on the topic of OMAP UARTs and power saving...
>  I note that there are now two drivers for the OMAP3 UART - omap-serial and
>  8250_omap.
>  I also note that your commit:
> 
> commit a2fc36613ac1af2e92cbed7af80bc72d8114dd50
>     ARM: OMAP3: Use manual idle for UARTs because of DMA errata
> 
>  is incompatible with omap-serial.  In particular, if I enable runtime
>  suspend of the serial port by setting the autosuspend_timeout, then incoming
>  characters will no longer wake the port (if I revert your patch incoming
>  chars do wake the port).
>  This could (I think) be fixed by enabling the RX/CTS interrupt.  However if
>  omap-serial is being deprecated, then there probably isn't any point.
> 
>  So: what is the longer term expectation for these drivers?  Should we be
>  switching over to 8250?

Yeah you should alredy be able to do it. Hopefully we'll have some
translation layer and the old omap-serial.c can be mostly removed
now that we have 8250 support with runtime PM :)

Regards,

Tony

[PATCH 12/13] ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

[Tony Lindgren]

* NeilBrown <neilb@suse.de> [150123 14:31]:
> On Thu, 22 Jan 2015 13:40:53 -0800 Tony Lindgren <tony@atomide.com> wrote:
> > >  
> > > +&uart4 {
> > > +	status = "disabled";
> > > +};
> > > +
> > 
> > This you probably want to avoid from PM point of view. Depending on
> > bootloader state of uart4, Linux may or may not be able to hit any
> > deeper power states.
> > 
> > Marking something with status = "disabled" in dts causes the device
> > entry not even to be created. That means hwmod won't be able to reset
> > and idle this device during boot.
> > 
> > The uart4 device is there for sure even if not muxed and in incomplete
> > state. You may want to also check other places where you're using
> > status = "disabled" for the same reasons.
> 
> That's ... unfortunate.  Would that apply to the MCBSPs too?  They are
> disabled by default so you would need to explicitly enable them all for
> sensible behaviour....

Yeah that applies to all the SoC integrated devices that the bus code
(hwmod) is supposed to reset and idle if unused. Basically anything
that depends on the dev entry being created.
 
> Hopefully there is some way to mark as device as "this is not used, make sure
> it is turned off and stays off" ???

Not currently that I know of :) To do that, we should add something
like status = "incomplete" where the dev entry gets created but the
driver is never probed. And incomplete here meaning that the device
is missing some parts like pins that would make it work properly.
 
> Thanks for the heads-up.  I'll have a look and see exactly what is happening.

OK
 
> BTW, on the topic of OMAP UARTs and power saving...
>  I note that there are now two drivers for the OMAP3 UART - omap-serial and
>  8250_omap.
>  I also note that your commit:
> 
> commit a2fc36613ac1af2e92cbed7af80bc72d8114dd50
>     ARM: OMAP3: Use manual idle for UARTs because of DMA errata
> 
>  is incompatible with omap-serial.  In particular, if I enable runtime
>  suspend of the serial port by setting the autosuspend_timeout, then incoming
>  characters will no longer wake the port (if I revert your patch incoming
>  chars do wake the port).
>  This could (I think) be fixed by enabling the RX/CTS interrupt.  However if
>  omap-serial is being deprecated, then there probably isn't any point.
> 
>  So: what is the longer term expectation for these drivers?  Should we be
>  switching over to 8250?

Yeah you should alredy be able to do it. Hopefully we'll have some
translation layer and the old omap-serial.c can be mostly removed
now that we have 8250 support with runtime PM :)

Regards,

Tony

[PATCH 13/13] ARM: dts: omap3-gta04: Disable keypad

[Marek Belisko]

From: NeilBrown <neil@brown.name>

The twl4030 keypad is not wired up in the gta04, so mark it disabled
to avoid pointless initialization.

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 8d2b0a1..b3ecf1f 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -342,6 +342,10 @@
 	status = "disabled";
 };
 
+&twl_keypad {
+	status = "disabled";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>;
-- 
1.9.1

[PATCH 13/13] ARM: dts: omap3-gta04: Disable keypad

[Marek Belisko]

From: NeilBrown <neil@brown.name>

The twl4030 keypad is not wired up in the gta04, so mark it disabled
to avoid pointless initialization.

Signed-off-by: NeilBrown <neil@brown.name>
---
 arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 8d2b0a1..b3ecf1f 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -342,6 +342,10 @@
 	status = "disabled";
 };
 
+&twl_keypad {
+	status = "disabled";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>;
-- 
1.9.1

Re: [PATCH 00/13] ARM: dts: omap3-gta04: Various DT fixes

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [150122 12:41]:
> This series contains fixes for gta04 devicetree. I collected patches
> from H. Nikolaus Schaller + NeilBrown and myself. Patches contains mostly fixes
> + adding new nodes and comments. All changes tested on gta04a4 board.
> 
> H. Nikolaus Schaller (5):
>   ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
>   ARM: dts: omap3-gta04: Fix audio node malformatting
>   ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
>   ARM: dts: omap3-gta04: Enable twl audio vibra support
>   ARM: dts: omap3-gta04: Enable power-off using twl4030
> 
> Marek Belisko (2):
>   ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
>   ARM: dts: omap3-gta04: Add ramp value for twl4030 audio
> 
> NeilBrown (6):
>   ARM: dts: omap3-gta04: add comments about gpios
>   ARM: dts: omap3-gta04: enable power-off for wifi card.
>   ARM: dts: omap3-gta04: add gyroscope
>   ARM: dts: omap3-gta04: only power DSS when necessary.
>   ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

Applying all except the uart4 "disabled" patch into omap-for-v3.20/dt
thanks.

Tony

>   ARM: dts: omap3-gta04: Disable keypad
> 
>  arch/arm/boot/dts/omap3-gta04.dtsi | 54 +++++++++++++++++++++++++++-----------
>  1 file changed, 39 insertions(+), 15 deletions(-)
> 
> -- 
> 1.9.1
> 

[PATCH 00/13] ARM: dts: omap3-gta04: Various DT fixes

[Tony Lindgren]

* Marek Belisko <marek@goldelico.com> [150122 12:41]:
> This series contains fixes for gta04 devicetree. I collected patches
> from H. Nikolaus Schaller + NeilBrown and myself. Patches contains mostly fixes
> + adding new nodes and comments. All changes tested on gta04a4 board.
> 
> H. Nikolaus Schaller (5):
>   ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
>   ARM: dts: omap3-gta04: Fix audio node malformatting
>   ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
>   ARM: dts: omap3-gta04: Enable twl audio vibra support
>   ARM: dts: omap3-gta04: Enable power-off using twl4030
> 
> Marek Belisko (2):
>   ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
>   ARM: dts: omap3-gta04: Add ramp value for twl4030 audio
> 
> NeilBrown (6):
>   ARM: dts: omap3-gta04: add comments about gpios
>   ARM: dts: omap3-gta04: enable power-off for wifi card.
>   ARM: dts: omap3-gta04: add gyroscope
>   ARM: dts: omap3-gta04: only power DSS when necessary.
>   ARM: dts: omap3-gta04: uart4 is not connected, so mark it "disabled"

Applying all except the uart4 "disabled" patch into omap-for-v3.20/dt
thanks.

Tony

>   ARM: dts: omap3-gta04: Disable keypad
> 
>  arch/arm/boot/dts/omap3-gta04.dtsi | 54 +++++++++++++++++++++++++++-----------
>  1 file changed, 39 insertions(+), 15 deletions(-)
> 
> -- 
> 1.9.1
>