* [PATCH v5 0/5] iio: Add sensorhub driver
@ 2015-01-28 14:05 Karol Wrona
2015-01-28 14:05 ` [PATCH v5 1/5] iio: common: ssp_sensors: " Karol Wrona
` (4 more replies)
0 siblings, 5 replies; 19+ messages in thread
From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw)
To: Jonathan Cameron, linux-iio, devicetree, linux-kernel
Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona,
Karol Wrona
Hello,
This patchset adds support for sensorhub. It is an external mcu which
manages and collects data from several sensors i.e. on Galaxy Gear 2 watch.
It contains:
- spi driver for sensorhub device
- DT binding for the device
- IIO common utils for ssp sensors (iio kfifo setup helpers, pre/post callbacks)
- IIO accelerometer driver
- IIO gyroscope driver
For now the driver supports "traditional" sensors but new ones types are
intended to be used.
The patchset depends on INDIO_BUFFER_SOFTWARE adding patch.
>From v1:
- Adopted to new stm32fwu v5
- Fixed sensors' data process callbacks
- Fixed comments style
>From v2:
- Fixes after Hartmut Knaack review
- Sensorhub driver was moved from misc to iio after the discussion with Arnd
and Jonathan
- Firmware upgrade is not supported in this patchset. I hope it will be
applied when it will find its own place in the tree.
>From v3:
- change buffer allocation manner for iio devices buffers
- centralize irq buffer
- style fixes
- sensors' devices as mfd cells
- remove iio_buffer_register from the sensorhub drivers
- fix DT binding and remove optional attributes
>From v4:
- fix Kconfig - missing MFD_CORE dependency
- rebase on next-20150128
- remove THIS_MODULE usage in sensors' drivers as not needed
Thanks,
Karol
Karol Wrona (5):
iio: common: ssp_sensors: Add sensorhub driver
iio: sensorhub: Add sensorhub bindings
iio: common: ssp_sensors: Add sensorhub iio commons
iio: common: ssp_sensors: Add sensorhub accelerometer sensor
iio: common: ssp_sensors: Add sensorhub gyroscope sensor
.../devicetree/bindings/iio/sensorhub.txt | 25 +
drivers/iio/accel/Makefile | 1 +
drivers/iio/accel/ssp_accel_sensor.c | 169 +++++
drivers/iio/common/Kconfig | 1 +
drivers/iio/common/Makefile | 1 +
drivers/iio/common/ssp_sensors/Kconfig | 26 +
drivers/iio/common/ssp_sensors/Makefile | 8 +
drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++
drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++
drivers/iio/common/ssp_sensors/ssp_iio.c | 107 +++
drivers/iio/common/ssp_sensors/ssp_iio_sensor.h | 70 ++
drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++
drivers/iio/gyro/Makefile | 2 +
drivers/iio/gyro/ssp_gyro_sensor.c | 168 +++++
include/linux/iio/common/ssp_sensors.h | 82 +++
15 files changed, 2237 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/sensorhub.txt
create mode 100644 drivers/iio/accel/ssp_accel_sensor.c
create mode 100644 drivers/iio/common/ssp_sensors/Kconfig
create mode 100644 drivers/iio/common/ssp_sensors/Makefile
create mode 100644 drivers/iio/common/ssp_sensors/ssp.h
create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c
create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio.c
create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio_sensor.h
create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c
create mode 100644 drivers/iio/gyro/ssp_gyro_sensor.c
create mode 100644 include/linux/iio/common/ssp_sensors.h
--
1.7.9.5
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH v5 1/5] iio: common: ssp_sensors: Add sensorhub driver 2015-01-28 14:05 [PATCH v5 0/5] iio: Add sensorhub driver Karol Wrona @ 2015-01-28 14:05 ` Karol Wrona 2015-01-29 18:35 ` Jonathan Cameron 2015-01-28 14:05 ` Karol Wrona ` (3 subsequent siblings) 4 siblings, 1 reply; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona Sensorhub is MCU dedicated to collect data and manage several sensors. Sensorhub is a spi device which provides a layer for IIO devices. It provides some data parsing and common mechanism for sensorhub sensors. Adds common sensorhub library for sensorhub driver and iio drivers which uses sensorhub MCU to communicate with sensors. Signed-off-by: Karol Wrona <k.wrona@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> --- drivers/iio/common/Kconfig | 1 + drivers/iio/common/Makefile | 1 + drivers/iio/common/ssp_sensors/Kconfig | 26 ++ drivers/iio/common/ssp_sensors/Makefile | 8 + drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++++++ drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++++++++++++ drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++++++++++ include/linux/iio/common/ssp_sensors.h | 82 ++++ 8 files changed, 1695 insertions(+) create mode 100644 drivers/iio/common/ssp_sensors/Kconfig create mode 100644 drivers/iio/common/ssp_sensors/Makefile create mode 100644 drivers/iio/common/ssp_sensors/ssp.h create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c create mode 100644 include/linux/iio/common/ssp_sensors.h diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig index 0b6e97d..790f106 100644 --- a/drivers/iio/common/Kconfig +++ b/drivers/iio/common/Kconfig @@ -3,4 +3,5 @@ # source "drivers/iio/common/hid-sensors/Kconfig" +source "drivers/iio/common/ssp_sensors/Kconfig" source "drivers/iio/common/st_sensors/Kconfig" diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile index 3112df0..b1e4d9c 100644 --- a/drivers/iio/common/Makefile +++ b/drivers/iio/common/Makefile @@ -8,4 +8,5 @@ # When adding new entries keep the list in alphabetical order obj-y += hid-sensors/ +obj-y += ssp_sensors/ obj-y += st_sensors/ diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig new file mode 100644 index 0000000..0ea4faf --- /dev/null +++ b/drivers/iio/common/ssp_sensors/Kconfig @@ -0,0 +1,26 @@ +# +# SSP sensor drivers and commons configuration +# +menu "SSP Sensor Common" + +config IIO_SSP_SENSORS_COMMONS + tristate "Commons for all SSP Sensor IIO drivers" + depends on IIO_SSP_SENSORHUB + select IIO_BUFFER + select IIO_KFIFO_BUF + help + Say yes here to build commons for SSP sensors. + To compile this as a module, choose M here: the module + will be called ssp_iio. + +config IIO_SSP_SENSORHUB + tristate "Samsung Sensorhub driver" + depends on SPI + select MFD_CORE + help + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. + To compile this driver as a module, choose M here: the + module will be called sensorhub. + +endmenu diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile new file mode 100644 index 0000000..1e0389e --- /dev/null +++ b/drivers/iio/common/ssp_sensors/Makefile @@ -0,0 +1,8 @@ +# +# Makefile for SSP sensor drivers and commons. +# + +sensorhub-objs := ssp_dev.o ssp_spi.o +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o + +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_iio.o diff --git a/drivers/iio/common/ssp_sensors/ssp.h b/drivers/iio/common/ssp_sensors/ssp.h new file mode 100644 index 0000000..b910e91 --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp.h @@ -0,0 +1,257 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __SSP_SENSORHUB_H__ +#define __SSP_SENSORHUB_H__ + +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/iio.h> +#include <linux/spi/spi.h> + +#define SSP_DEVICE_ID 0x55 + +#ifdef SSP_DBG +#define ssp_dbg(format, ...) pr_info("[SSP] "format, ##__VA_ARGS__) +#else +#define ssp_dbg(format, ...) +#endif + +#define SSP_SW_RESET_TIME 3000 +/* Sensor polling in ms */ +#define SSP_DEFAULT_POLLING_DELAY 200 +#define SSP_DEFAULT_RETRIES 3 +#define SSP_DATA_PACKET_SIZE 960 +#define SSP_HEADER_BUFFER_SIZE 4 + +enum { + SSP_KERNEL_BINARY = 0, + SSP_KERNEL_CRASHED_BINARY, +}; + +enum { + SSP_INITIALIZATION_STATE = 0, + SSP_NO_SENSOR_STATE, + SSP_ADD_SENSOR_STATE, + SSP_RUNNING_SENSOR_STATE, +}; + +/* Firmware download STATE */ +enum { + SSP_FW_DL_STATE_FAIL = -1, + SSP_FW_DL_STATE_NONE = 0, + SSP_FW_DL_STATE_NEED_TO_SCHEDULE, + SSP_FW_DL_STATE_SCHEDULED, + SSP_FW_DL_STATE_DOWNLOADING, + SSP_FW_DL_STATE_SYNC, + SSP_FW_DL_STATE_DONE, +}; + +#define SSP_INVALID_REVISION 99999 +#define SSP_INVALID_REVISION2 0xffffff + +/* AP -> SSP Instruction */ +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD 0xa1 +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_RM 0xa2 +#define SSP_MSG2SSP_INST_REMOVE_ALL 0xa3 +#define SSP_MSG2SSP_INST_CHANGE_DELAY 0xa4 +#define SSP_MSG2SSP_INST_LIBRARY_ADD 0xb1 +#define SSP_MSG2SSP_INST_LIBRARY_REMOVE 0xb2 +#define SSP_MSG2SSP_INST_LIB_NOTI 0xb4 +#define SSP_MSG2SSP_INST_LIB_DATA 0xc1 + +#define SSP_MSG2SSP_AP_MCU_SET_GYRO_CAL 0xcd +#define SSP_MSG2SSP_AP_MCU_SET_ACCEL_CAL 0xce +#define SSP_MSG2SSP_AP_STATUS_SHUTDOWN 0xd0 +#define SSP_MSG2SSP_AP_STATUS_WAKEUP 0xd1 +#define SSP_MSG2SSP_AP_STATUS_SLEEP 0xd2 +#define SSP_MSG2SSP_AP_STATUS_RESUME 0xd3 +#define SSP_MSG2SSP_AP_STATUS_SUSPEND 0xd4 +#define SSP_MSG2SSP_AP_STATUS_RESET 0xd5 +#define SSP_MSG2SSP_AP_STATUS_POW_CONNECTED 0xd6 +#define SSP_MSG2SSP_AP_STATUS_POW_DISCONNECTED 0xd7 +#define SSP_MSG2SSP_AP_TEMPHUMIDITY_CAL_DONE 0xda +#define SSP_MSG2SSP_AP_MCU_SET_DUMPMODE 0xdb +#define SSP_MSG2SSP_AP_MCU_DUMP_CHECK 0xdc +#define SSP_MSG2SSP_AP_MCU_BATCH_FLUSH 0xdd +#define SSP_MSG2SSP_AP_MCU_BATCH_COUNT 0xdf + +#define SSP_MSG2SSP_AP_WHOAMI 0x0f +#define SSP_MSG2SSP_AP_FIRMWARE_REV 0xf0 +#define SSP_MSG2SSP_AP_SENSOR_FORMATION 0xf1 +#define SSP_MSG2SSP_AP_SENSOR_PROXTHRESHOLD 0xf2 +#define SSP_MSG2SSP_AP_SENSOR_BARCODE_EMUL 0xf3 +#define SSP_MSG2SSP_AP_SENSOR_SCANNING 0xf4 +#define SSP_MSG2SSP_AP_SET_MAGNETIC_HWOFFSET 0xf5 +#define SSP_MSG2SSP_AP_GET_MAGNETIC_HWOFFSET 0xf6 +#define SSP_MSG2SSP_AP_SENSOR_GESTURE_CURRENT 0xf7 +#define SSP_MSG2SSP_AP_GET_THERM 0xf8 +#define SSP_MSG2SSP_AP_GET_BIG_DATA 0xf9 +#define SSP_MSG2SSP_AP_SET_BIG_DATA 0xfa +#define SSP_MSG2SSP_AP_START_BIG_DATA 0xfb +#define SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX 0xfd +#define SSP_MSG2SSP_AP_SENSOR_TILT 0xea +#define SSP_MSG2SSP_AP_MCU_SET_TIME 0xfe +#define SSP_MSG2SSP_AP_MCU_GET_TIME 0xff + +#define SSP_MSG2SSP_AP_FUSEROM 0x01 + +/* voice data */ +#define SSP_TYPE_WAKE_UP_VOICE_SERVICE 0x01 +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_AM 0x01 +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_GRAMMER 0x02 + +/* Factory Test */ +#define SSP_ACCELEROMETER_FACTORY 0x80 +#define SSP_GYROSCOPE_FACTORY 0x81 +#define SSP_GEOMAGNETIC_FACTORY 0x82 +#define SSP_PRESSURE_FACTORY 0x85 +#define SSP_GESTURE_FACTORY 0x86 +#define SSP_TEMPHUMIDITY_CRC_FACTORY 0x88 +#define SSP_GYROSCOPE_TEMP_FACTORY 0x8a +#define SSP_GYROSCOPE_DPS_FACTORY 0x8b +#define SSP_MCU_FACTORY 0x8c +#define SSP_MCU_SLEEP_FACTORY 0x8d + +/* SSP -> AP ACK about write CMD */ +#define SSP_MSG_ACK 0x80 /* ACK from SSP to AP */ +#define SSP_MSG_NAK 0x70 /* NAK from SSP to AP */ + +struct ssp_sensorhub_info { + char *fw_name; + char *fw_crashed_name; + unsigned int fw_rev; + const u8 * const mag_table; + const unsigned int mag_length; +}; + +/* ssp_msg options bit */ +#define SSP_RW 0 +#define SSP_INDEX 3 + +#define SSP_AP2HUB_READ 0 +#define SSP_AP2HUB_WRITE 1 +#define SSP_HUB2AP_WRITE 2 +#define SSP_AP2HUB_READY 3 +#define SSP_AP2HUB_RETURN 4 + +/** + * struct ssp_data - ssp platformdata structure + * @spi: spi device + * @sensorhub_info: info about sensorhub board specific features + * @wdt_timer: watchdog timer + * @work_wdt: watchdog work + * @work_firmware: firmware upgrade work queue + * @work_refresh: refresh work queue for reset request from MCU + * @shut_down: shut down flag + * @mcu_dump_mode: mcu dump mode for debug + * @time_syncing: time syncing indication flag + * @timestamp: previous time in ns calculated for time syncing + * @check_status: status table for each sensor + * @com_fail_cnt: communication fail count + * @reset_cnt: reset count + * @timeout_cnt: timeout count + * @available_sensors: available sensors seen by sensorhub (bit array) + * @cur_firm_rev: cached current firmware revision + * @last_resume_state: last AP resume/suspend state used to handle the PM + * state of ssp + * @last_ap_state: (obsolete) sleep notification for MCU + * @sensor_enable: sensor enable mask + * @delay_buf: data acquisition intervals table + * @batch_latency_buf: yet unknown but existing in communication protocol + * @batch_opt_buf: yet unknown but existing in communication protocol + * @accel_position: yet unknown but existing in communication protocol + * @mag_position: yet unknown but existing in communication protocol + * @fw_dl_state: firmware download state + * @comm_lock: lock protecting the handshake + * @pending_lock: lock protecting pending list and completion + * @mcu_reset_gpio: mcu reset line + * @ap_mcu_gpio: ap to mcu gpio line + * @mcu_ap_gpio: mcu to ap gpio line + * @pending_list: pending list for messages queued to be sent/read + * @sensor_devs: registered IIO devices table + * @enable_refcount: enable reference count for wdt (watchdog timer) + * @header_buffer: cache aligned buffer for packet header + */ +struct ssp_data { + struct spi_device *spi; + struct ssp_sensorhub_info *sensorhub_info; + struct timer_list wdt_timer; + struct work_struct work_wdt; + struct delayed_work work_refresh; + + bool shut_down; + bool mcu_dump_mode; + bool time_syncing; + int64_t timestamp; + + int check_status[SSP_SENSOR_MAX]; + + unsigned int com_fail_cnt; + unsigned int reset_cnt; + unsigned int timeout_cnt; + + unsigned int available_sensors; + unsigned int cur_firm_rev; + + char last_resume_state; + char last_ap_state; + + unsigned int sensor_enable; + u32 delay_buf[SSP_SENSOR_MAX]; + s32 batch_latency_buf[SSP_SENSOR_MAX]; + s8 batch_opt_buf[SSP_SENSOR_MAX]; + + int accel_position; + int mag_position; + int fw_dl_state; + + struct mutex comm_lock; + struct mutex pending_lock; + + int mcu_reset_gpio; + int ap_mcu_gpio; + int mcu_ap_gpio; + + struct list_head pending_list; + + struct iio_dev *sensor_devs[SSP_SENSOR_MAX]; + atomic_t enable_refcount; + + __le16 header_buffer[SSP_HEADER_BUFFER_SIZE / sizeof(__le16)] + ____cacheline_aligned; +}; + +void ssp_clean_pending_list(struct ssp_data *data); + +int ssp_command(struct ssp_data *data, char command, int arg); + +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, + u8 *send_buf, u8 length); + +int ssp_irq_msg(struct ssp_data *data); + +int ssp_get_chipid(struct ssp_data *data); + +int ssp_set_magnetic_matrix(struct ssp_data *data); + +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data); + +unsigned int ssp_get_firmware_rev(struct ssp_data *data); + +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay); + +#endif /* __SSP_SENSORHUB_H__ */ diff --git a/drivers/iio/common/ssp_sensors/ssp_dev.c b/drivers/iio/common/ssp_sensors/ssp_dev.c new file mode 100644 index 0000000..6b22115 --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp_dev.c @@ -0,0 +1,712 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/iio.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/mfd/core.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_platform.h> +#include "ssp.h" + +#define SSP_WDT_TIME 10000 +#define SSP_LIMIT_RESET_CNT 20 +#define SSP_LIMIT_TIMEOUT_CNT 3 + +/* It is possible that it is max clk rate for version 1.0 of bootcode */ +#define SSP_BOOT_SPI_HZ 400000 + +/* + * These fields can look enigmatic but this structure is used mainly to flat + * some values and depends on command type. + */ +struct ssp_instruction { + __le32 a; + __le32 b; + u8 c; +} __attribute__((__packed__)); + +static const u8 ssp_magnitude_table[] = {110, 85, 171, 71, 203, 195, 0, 67, + 208, 56, 175, 244, 206, 213, 0, 92, 250, 0, 55, 48, 189, 252, 171, + 243, 13, 45, 250}; + +static const struct ssp_sensorhub_info ssp_rinato_info = { + .fw_name = "ssp_B2.fw", + .fw_crashed_name = "ssp_crashed.fw", + .fw_rev = 14052300, + .mag_table = ssp_magnitude_table, + .mag_length = ARRAY_SIZE(ssp_magnitude_table), +}; + +static const struct ssp_sensorhub_info ssp_thermostat_info = { + .fw_name = "thermostat_B2.fw", + .fw_crashed_name = "ssp_crashed.fw", + .fw_rev = 14080600, + .mag_table = ssp_magnitude_table, + .mag_length = ARRAY_SIZE(ssp_magnitude_table), +}; + +static const struct mfd_cell sensorhub_sensor_devs[] = { + { + .name = "ssp-accelerometer", + }, + { + .name = "ssp-gyroscope", + }, +}; + +static void ssp_toggle_mcu_reset_gpio(struct ssp_data *data) +{ + gpio_set_value(data->mcu_reset_gpio, 0); + usleep_range(1000, 1200); + gpio_set_value(data->mcu_reset_gpio, 1); + msleep(50); +} + +static void ssp_sync_available_sensors(struct ssp_data *data) +{ + int i, ret; + + for (i = 0; i < SSP_SENSOR_MAX; ++i) { + if (data->available_sensors & BIT(i)) { + ret = ssp_enable_sensor(data, i, data->delay_buf[i]); + if (ret < 0) { + dev_err(&data->spi->dev, + "Sync sensor nr: %d fail\n", i); + continue; + } + } + } + + ret = ssp_command(data, SSP_MSG2SSP_AP_MCU_SET_DUMPMODE, + data->mcu_dump_mode); + if (ret < 0) + dev_err(&data->spi->dev, + "SSP_MSG2SSP_AP_MCU_SET_DUMPMODE failed\n"); +} + +static void ssp_enable_mcu(struct ssp_data *data, bool enable) +{ + dev_info(&data->spi->dev, "current shutdown = %d, old = %d\n", enable, + data->shut_down); + + if (enable && data->shut_down) { + data->shut_down = false; + enable_irq(data->spi->irq); + enable_irq_wake(data->spi->irq); + } else if (!enable && !data->shut_down) { + data->shut_down = true; + disable_irq(data->spi->irq); + disable_irq_wake(data->spi->irq); + } else { + dev_warn(&data->spi->dev, "current shutdown = %d, old = %d\n", + enable, data->shut_down); + } +} + +/* + * This function is the first one which communicates with the mcu so it is + * possible that the first attempt will fail + */ +static int ssp_check_fwbl(struct ssp_data *data) +{ + int retries = 0; + + while (retries++ < 5) { + data->cur_firm_rev = ssp_get_firmware_rev(data); + if (data->cur_firm_rev == SSP_INVALID_REVISION || + data->cur_firm_rev == SSP_INVALID_REVISION2) { + dev_warn(&data->spi->dev, + "Invalid revision, trying %d time\n", retries); + } else { + break; + } + } + + if (data->cur_firm_rev == SSP_INVALID_REVISION || + data->cur_firm_rev == SSP_INVALID_REVISION2) { + dev_err(&data->spi->dev, "SSP_INVALID_REVISION\n"); + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; + } + + dev_info(&data->spi->dev, + "MCU Firm Rev : Old = %8u, New = %8u\n", + data->cur_firm_rev, + data->sensorhub_info->fw_rev); + + if (data->cur_firm_rev != data->sensorhub_info->fw_rev) + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; + + return SSP_FW_DL_STATE_NONE; +} + +static void ssp_reset_mcu(struct ssp_data *data) +{ + ssp_enable_mcu(data, false); + ssp_clean_pending_list(data); + ssp_toggle_mcu_reset_gpio(data); + ssp_enable_mcu(data, true); +} + +static void ssp_wdt_work_func(struct work_struct *work) +{ + struct ssp_data *data = container_of(work, struct ssp_data, work_wdt); + + dev_err(&data->spi->dev, "%s - Sensor state: 0x%x, RC: %u, CC: %u\n", + __func__, data->available_sensors, data->reset_cnt, + data->com_fail_cnt); + + ssp_reset_mcu(data); + data->com_fail_cnt = 0; + data->timeout_cnt = 0; +} + +static void ssp_wdt_timer_func(unsigned long ptr) +{ + struct ssp_data *data = (struct ssp_data *)ptr; + + switch (data->fw_dl_state) { + case SSP_FW_DL_STATE_FAIL: + case SSP_FW_DL_STATE_DOWNLOADING: + case SSP_FW_DL_STATE_SYNC: + goto _mod; + } + + if (data->timeout_cnt > SSP_LIMIT_TIMEOUT_CNT || + data->com_fail_cnt > SSP_LIMIT_RESET_CNT) + queue_work(system_power_efficient_wq, &data->work_wdt); +_mod: + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); +} + +static void ssp_enable_wdt_timer(struct ssp_data *data) +{ + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); +} + +static void ssp_disable_wdt_timer(struct ssp_data *data) +{ + del_timer_sync(&data->wdt_timer); + cancel_work_sync(&data->work_wdt); +} + +/** + * ssp_get_sensor_delay() - gets sensor data acquisition period + * @data: sensorhub structure + * @type: SSP sensor type + * + * Returns acquisition period in ms + */ +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type type) +{ + return data->delay_buf[type]; +} +EXPORT_SYMBOL(ssp_get_sensor_delay); + +/** + * ssp_enable_sensor() - enables data acquisition for sensor + * @data: sensorhub structure + * @type: SSP sensor type + * @delay: delay in ms + * + * Returns 0 or negative value in case of error + */ +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, + u32 delay) +{ + int ret; + struct ssp_instruction to_send; + + to_send.a = cpu_to_le32(delay); + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); + to_send.c = data->batch_opt_buf[type]; + + switch (data->check_status[type]) { + case SSP_INITIALIZATION_STATE: + /* do calibration step, now just enable */ + case SSP_ADD_SENSOR_STATE: + ret = ssp_send_instruction(data, + SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD, + type, + (u8 *)&to_send, sizeof(to_send)); + if (ret < 0) { + dev_err(&data->spi->dev, "Enabling sensor failed\n"); + data->check_status[type] = SSP_NO_SENSOR_STATE; + goto derror; + } + + data->sensor_enable |= BIT(type); + data->check_status[type] = SSP_RUNNING_SENSOR_STATE; + break; + case SSP_RUNNING_SENSOR_STATE: + ret = ssp_send_instruction(data, + SSP_MSG2SSP_INST_CHANGE_DELAY, type, + (u8 *)&to_send, sizeof(to_send)); + if (ret < 0) { + dev_err(&data->spi->dev, + "Changing sensor delay failed\n"); + goto derror; + } + break; + default: + data->check_status[type] = SSP_ADD_SENSOR_STATE; + break; + } + + data->delay_buf[type] = delay; + + if (atomic_inc_return(&data->enable_refcount) == 1) + ssp_enable_wdt_timer(data); + + return 0; + +derror: + return ret; +} +EXPORT_SYMBOL(ssp_enable_sensor); + +/** + * ssp_change_delay() - changes data acquisition for sensor + * @data: sensorhub structure + * @type: SSP sensor type + * @delay: delay in ms + * + * Returns 0 or negative value in case of error + */ +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, + u32 delay) +{ + int ret; + struct ssp_instruction to_send; + + to_send.a = cpu_to_le32(delay); + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); + to_send.c = data->batch_opt_buf[type]; + + ret = ssp_send_instruction(data, SSP_MSG2SSP_INST_CHANGE_DELAY, type, + (u8 *)&to_send, sizeof(to_send)); + if (ret < 0) { + dev_err(&data->spi->dev, "Changing sensor delay failed\n"); + return ret; + } + + data->delay_buf[type] = delay; + + return 0; +} +EXPORT_SYMBOL(ssp_change_delay); + +/** + * ssp_disable_sensor() - disables sensor + * + * @data: sensorhub structure + * @type: SSP sensor type + * + * Returns 0 or negative value in case of error + */ +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type) +{ + int ret; + __le32 command; + + if (data->sensor_enable & BIT(type)) { + command = cpu_to_le32(data->delay_buf[type]); + + ret = ssp_send_instruction(data, + SSP_MSG2SSP_INST_BYPASS_SENSOR_RM, + type, (u8 *)&command, + sizeof(command)); + if (ret < 0) { + dev_err(&data->spi->dev, "Remove sensor fail\n"); + return ret; + } + + data->sensor_enable &= ~BIT(type); + } + + data->check_status[type] = SSP_ADD_SENSOR_STATE; + + if (atomic_dec_and_test(&data->enable_refcount)) + ssp_disable_wdt_timer(data); + + return 0; +} +EXPORT_SYMBOL(ssp_disable_sensor); + +static irqreturn_t ssp_irq_thread_fn(int irq, void *dev_id) +{ + struct ssp_data *data = dev_id; + + /* + * This wrapper is done to preserve error path for ssp_irq_msg, also + * it is defined in different file. + */ + ssp_irq_msg(data); + + return IRQ_HANDLED; +} + +static int ssp_initialize_mcu(struct ssp_data *data) +{ + int ret; + + ssp_clean_pending_list(data); + + ret = ssp_get_chipid(data); + if (ret != SSP_DEVICE_ID) { + dev_err(&data->spi->dev, "%s - MCU %s ret = %d\n", __func__, + ret < 0 ? "is not working" : "identification failed", + ret); + return ret < 0 ? ret : -ENODEV; + } + + dev_info(&data->spi->dev, "MCU device ID = %d\n", ret); + + /* + * needs clarification, for now do not want to export all transfer + * methods to sensors' drivers + */ + ret = ssp_set_magnetic_matrix(data); + if (ret < 0) { + dev_err(&data->spi->dev, + "%s - ssp_set_magnetic_matrix failed\n", __func__); + return ret; + } + + data->available_sensors = ssp_get_sensor_scanning_info(data); + if (data->available_sensors == 0) { + dev_err(&data->spi->dev, + "%s - ssp_get_sensor_scanning_info failed\n", __func__); + return -EIO; + } + + data->cur_firm_rev = ssp_get_firmware_rev(data); + dev_info(&data->spi->dev, "MCU Firm Rev : New = %8u\n", + data->cur_firm_rev); + + return ssp_command(data, SSP_MSG2SSP_AP_MCU_DUMP_CHECK, 0); +} + +/* + * sensorhub can request its reinitialization as some brutal and rare error + * handling. It can be requested from the MCU. + */ +static void ssp_refresh_task(struct work_struct *work) +{ + struct ssp_data *data = container_of((struct delayed_work *)work, + struct ssp_data, work_refresh); + + dev_info(&data->spi->dev, "refreshing\n"); + + data->reset_cnt++; + + if (ssp_initialize_mcu(data) >= 0) { + ssp_sync_available_sensors(data); + if (data->last_ap_state != 0) + ssp_command(data, data->last_ap_state, 0); + + if (data->last_resume_state != 0) + ssp_command(data, data->last_resume_state, 0); + + data->timeout_cnt = 0; + data->com_fail_cnt = 0; + } +} + +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay) +{ + cancel_delayed_work_sync(&data->work_refresh); + + return queue_delayed_work(system_power_efficient_wq, + &data->work_refresh, + msecs_to_jiffies(delay)); +} + +#ifdef CONFIG_OF +static struct of_device_id ssp_of_match[] = { + { + .compatible = "samsung,sensorhub-rinato", + .data = &ssp_rinato_info, + }, { + .compatible = "samsung,sensorhub-thermostat", + .data = &ssp_thermostat_info, + }, + {}, +}; +MODULE_DEVICE_TABLE(of, ssp_of_match); + +static struct ssp_data *ssp_parse_dt(struct device *dev) +{ + int ret; + struct ssp_data *data; + struct device_node *node = dev->of_node; + const struct of_device_id *match; + + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); + if (!data) + return NULL; + + data->mcu_ap_gpio = of_get_named_gpio(node, "mcu-ap-gpios", 0); + if (data->mcu_ap_gpio < 0) + goto err_free_pd; + + data->ap_mcu_gpio = of_get_named_gpio(node, "ap-mcu-gpios", 0); + if (data->ap_mcu_gpio < 0) + goto err_free_pd; + + data->mcu_reset_gpio = of_get_named_gpio(node, "mcu-reset-gpios", 0); + if (data->mcu_reset_gpio < 0) + goto err_free_pd; + + ret = devm_gpio_request_one(dev, data->ap_mcu_gpio, GPIOF_OUT_INIT_HIGH, + "ap-mcu-gpios"); + if (ret) + goto err_free_pd; + + ret = devm_gpio_request_one(dev, data->mcu_reset_gpio, + GPIOF_OUT_INIT_HIGH, "mcu-reset-gpios"); + if (ret) + goto err_ap_mcu; + + match = of_match_node(ssp_of_match, node); + if (!match) + goto err_mcu_reset_gpio; + + data->sensorhub_info = (struct ssp_sensorhub_info *)match->data; + + dev_set_drvdata(dev, data); + + return data; + +err_mcu_reset_gpio: + devm_gpio_free(dev, data->mcu_reset_gpio); +err_ap_mcu: + devm_gpio_free(dev, data->ap_mcu_gpio); +err_free_pd: + devm_kfree(dev, data); + return NULL; +} +#else +static struct ssp_data *ssp_parse_dt(struct platform_device *pdev) +{ + return NULL; +} +#endif + +/** + * ssp_register_consumer() - registers iio consumer in ssp framework + * + * @indio_dev: consumer iio device + * @type: ssp sensor type + */ +void ssp_register_consumer(struct iio_dev *indio_dev, enum ssp_sensor_type type) +{ + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + data->sensor_devs[type] = indio_dev; +} +EXPORT_SYMBOL(ssp_register_consumer); + +static int ssp_probe(struct spi_device *spi) +{ + int ret, i; + struct ssp_data *data; + + data = ssp_parse_dt(&spi->dev); + if (!data) { + dev_err(&spi->dev, "Failed to find platform data\n"); + return -ENODEV; + } + + ret = mfd_add_devices(&spi->dev, -1, sensorhub_sensor_devs, + ARRAY_SIZE(sensorhub_sensor_devs), NULL, 0, NULL); + if (ret < 0) { + dev_err(&spi->dev, "mfd add devices fail\n"); + return ret; + } + + spi->mode = SPI_MODE_1; + ret = spi_setup(spi); + if (ret < 0) { + dev_err(&spi->dev, "Failed to setup spi\n"); + return ret; + } + + data->fw_dl_state = SSP_FW_DL_STATE_NONE; + data->spi = spi; + spi_set_drvdata(spi, data); + + mutex_init(&data->comm_lock); + + for (i = 0; i < SSP_SENSOR_MAX; ++i) { + data->delay_buf[i] = SSP_DEFAULT_POLLING_DELAY; + data->batch_latency_buf[i] = 0; + data->batch_opt_buf[i] = 0; + data->check_status[i] = SSP_INITIALIZATION_STATE; + } + + data->delay_buf[SSP_BIO_HRM_LIB] = 100; + + data->time_syncing = true; + + mutex_init(&data->pending_lock); + INIT_LIST_HEAD(&data->pending_list); + + atomic_set(&data->enable_refcount, 0); + + INIT_WORK(&data->work_wdt, ssp_wdt_work_func); + INIT_DELAYED_WORK(&data->work_refresh, ssp_refresh_task); + + setup_timer(&data->wdt_timer, ssp_wdt_timer_func, (unsigned long)data); + + ret = request_threaded_irq(data->spi->irq, NULL, + ssp_irq_thread_fn, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + "SSP_Int", data); + if (ret < 0) { + dev_err(&spi->dev, "Irq request fail\n"); + goto err_setup_irq; + } + + /* Let's start with enabled one so irq balance could be ok */ + data->shut_down = false; + + /* just to avoid unbalanced irq set wake up */ + enable_irq_wake(data->spi->irq); + + data->fw_dl_state = ssp_check_fwbl(data); + if (data->fw_dl_state == SSP_FW_DL_STATE_NONE) { + ret = ssp_initialize_mcu(data); + if (ret < 0) { + dev_err(&spi->dev, "Initialize_mcu failed\n"); + goto err_read_reg; + } + } else { + dev_err(&spi->dev, "Firmware version not supported\n"); + ret = -EPERM; + goto err_read_reg; + } + + return 0; + +err_read_reg: + free_irq(data->spi->irq, data); +err_setup_irq: + mutex_destroy(&data->pending_lock); + mutex_destroy(&data->comm_lock); + + dev_err(&spi->dev, "Probe failed!\n"); + + return ret; +} + +static int ssp_remove(struct spi_device *spi) +{ + struct ssp_data *data = spi_get_drvdata(spi); + + if (ssp_command(data, SSP_MSG2SSP_AP_STATUS_SHUTDOWN, 0) < 0) + dev_err(&data->spi->dev, + "SSP_MSG2SSP_AP_STATUS_SHUTDOWN failed\n"); + + ssp_enable_mcu(data, false); + ssp_disable_wdt_timer(data); + + ssp_clean_pending_list(data); + + free_irq(data->spi->irq, data); + + del_timer_sync(&data->wdt_timer); + cancel_work_sync(&data->work_wdt); + + mutex_destroy(&data->comm_lock); + mutex_destroy(&data->pending_lock); + + mfd_remove_devices(&spi->dev); + + return 0; +} + +static int ssp_suspend(struct device *dev) +{ + int ret; + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); + + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_SUSPEND; + + if (atomic_read(&data->enable_refcount) > 0) + ssp_disable_wdt_timer(data); + + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_SUSPEND, 0); + if (ret < 0) { + dev_err(&data->spi->dev, + "%s SSP_MSG2SSP_AP_STATUS_SUSPEND failed\n", __func__); + + ssp_enable_wdt_timer(data); + return ret; + } + + data->time_syncing = false; + disable_irq(data->spi->irq); + + return 0; +} + +static int ssp_resume(struct device *dev) +{ + int ret; + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); + + enable_irq(data->spi->irq); + + if (atomic_read(&data->enable_refcount) > 0) + ssp_enable_wdt_timer(data); + + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_RESUME, 0); + if (ret < 0) { + dev_err(&data->spi->dev, + "%s SSP_MSG2SSP_AP_STATUS_RESUME failed\n", __func__); + ssp_disable_wdt_timer(data); + return ret; + } + + /* timesyncing is set by MCU */ + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_RESUME; + + return 0; +} + +static const struct dev_pm_ops ssp_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(ssp_suspend, ssp_resume) +}; + +static struct spi_driver ssp_driver = { + .probe = ssp_probe, + .remove = ssp_remove, + .driver = { + .pm = &ssp_pm_ops, + .bus = &spi_bus_type, + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(ssp_of_match), + .name = "sensorhub" + }, +}; + +module_spi_driver(ssp_driver); + +MODULE_DESCRIPTION("ssp sensorhub driver"); +MODULE_AUTHOR("Samsung Electronics"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/common/ssp_sensors/ssp_spi.c b/drivers/iio/common/ssp_sensors/ssp_spi.c new file mode 100644 index 0000000..704284a --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp_spi.c @@ -0,0 +1,608 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include "ssp.h" + +#define SSP_DEV (&data->spi->dev) +#define SSP_GET_MESSAGE_TYPE(data) (data & (3 << SSP_RW)) + +/* + * SSP -> AP Instruction + * They tell what packet type can be expected. In the future there will + * be less of them. BYPASS means common sensor packets with accel, gyro, + * hrm etc. data. LIBRARY and META are mock-up's for now. + */ +#define SSP_MSG2AP_INST_BYPASS_DATA 0x37 +#define SSP_MSG2AP_INST_LIBRARY_DATA 0x01 +#define SSP_MSG2AP_INST_DEBUG_DATA 0x03 +#define SSP_MSG2AP_INST_BIG_DATA 0x04 +#define SSP_MSG2AP_INST_META_DATA 0x05 +#define SSP_MSG2AP_INST_TIME_SYNC 0x06 +#define SSP_MSG2AP_INST_RESET 0x07 + +#define SSP_UNIMPLEMENTED -1 + +struct ssp_msg_header { + u8 cmd; + __le16 length; + __le16 options; + __le32 data; +} __attribute__((__packed__)); + +struct ssp_msg { + u16 length; + u16 options; + struct list_head list; + struct completion *done; + struct ssp_msg_header *h; + char *buffer; +}; + +static const int ssp_offset_map[SSP_SENSOR_MAX] = { + [SSP_ACCELEROMETER_SENSOR] = SSP_ACCELEROMETER_SIZE + + SSP_TIME_SIZE, + [SSP_GYROSCOPE_SENSOR] = SSP_GYROSCOPE_SIZE + + SSP_TIME_SIZE, + [SSP_GEOMAGNETIC_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GEOMAGNETIC_RAW] = SSP_UNIMPLEMENTED, + [SSP_GEOMAGNETIC_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_PRESSURE_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GESTURE_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_PROXIMITY_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_TEMPERATURE_HUMIDITY_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_LIGHT_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_PROXIMITY_RAW] = SSP_UNIMPLEMENTED, + [SSP_ORIENTATION_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_STEP_DETECTOR] = SSP_UNIMPLEMENTED, + [SSP_SIG_MOTION_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GYRO_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GAME_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, + [SSP_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, + [SSP_STEP_COUNTER] = SSP_UNIMPLEMENTED, + [SSP_BIO_HRM_RAW] = SSP_BIO_HRM_RAW_SIZE + + SSP_TIME_SIZE, + [SSP_BIO_HRM_RAW_FAC] = SSP_BIO_HRM_RAW_FAC_SIZE + + SSP_TIME_SIZE, + [SSP_BIO_HRM_LIB] = SSP_BIO_HRM_LIB_SIZE + + SSP_TIME_SIZE, +}; + +#define SSP_HEADER_SIZE (sizeof(struct ssp_msg_header)) +#define SSP_HEADER_SIZE_ALIGNED (ALIGN(SSP_HEADER_SIZE, 4)) + +static struct ssp_msg *ssp_create_msg(u8 cmd, u16 len, u16 opt, u32 data) +{ + struct ssp_msg_header h; + struct ssp_msg *msg; + + msg = kzalloc(sizeof(*msg), GFP_KERNEL); + if (!msg) + return NULL; + + h.cmd = cmd; + h.length = cpu_to_le16(len); + h.options = cpu_to_le16(opt); + h.data = cpu_to_le32(data); + + msg->buffer = kzalloc(SSP_HEADER_SIZE_ALIGNED + len, + GFP_KERNEL | GFP_DMA); + if (!msg->buffer) { + kfree(msg); + return NULL; + } + + msg->length = len; + msg->options = opt; + + memcpy(msg->buffer, &h, SSP_HEADER_SIZE); + + return msg; +} + +/* + * It is a bit heavy to do it this way but often the function is used to compose + * the message from smaller chunks which are placed on the stack. Often the + * chunks are small so memcpy should be optimalized. + */ +static inline void ssp_fill_buffer(struct ssp_msg *m, unsigned int offset, + const void *src, unsigned int len) +{ + memcpy(&m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], src, len); +} + +static inline void ssp_get_buffer(struct ssp_msg *m, unsigned int offset, + void *dest, unsigned int len) +{ + memcpy(dest, &m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], len); +} + +#define SSP_GET_BUFFER_AT_INDEX(m, index) \ + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index]) +#define SSP_SET_BUFFER_AT_INDEX(m, index, val) \ + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index] = val) + +static void ssp_clean_msg(struct ssp_msg *m) +{ + kfree(m->buffer); + kfree(m); +} + +static int ssp_print_mcu_debug(char *data_frame, int *data_index, + int received_len) +{ + int length = data_frame[(*data_index)++]; + + if (length > received_len - *data_index || length <= 0) { + ssp_dbg("[SSP]: MSG From MCU-invalid debug length(%d/%d)\n", + length, received_len); + return length ? length : -EPROTO; + } + + ssp_dbg("[SSP]: MSG From MCU - %s\n", &data_frame[*data_index]); + + *data_index += length; + + return 0; +} + +/* + * It was designed that way - additional lines to some kind of handshake, + * please do not ask why - only the firmware guy can know it. + */ +static int ssp_check_lines(struct ssp_data *data, bool state) +{ + int delay_cnt = 0; + + gpio_set_value_cansleep(data->ap_mcu_gpio, state); + + while (gpio_get_value_cansleep(data->mcu_ap_gpio) != state) { + usleep_range(3000, 3500); + + if (data->shut_down || delay_cnt++ > 500) { + dev_err(SSP_DEV, "%s:timeout, hw ack wait fail %d\n", + __func__, state); + + if (!state) + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); + + return -ETIMEDOUT; + } + } + + return 0; +} + +static int ssp_do_transfer(struct ssp_data *data, struct ssp_msg *msg, + struct completion *done, int timeout) +{ + int status; + /* + * check if this is a short one way message or the whole transfer has + * second part after an interrupt + */ + const bool use_no_irq = msg->length == 0; + + if (data->shut_down) + return -EPERM; + + msg->done = done; + + mutex_lock(&data->comm_lock); + + status = ssp_check_lines(data, false); + if (status < 0) + goto _error_locked; + + status = spi_write(data->spi, msg->buffer, SSP_HEADER_SIZE); + if (status < 0) { + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); + dev_err(SSP_DEV, "%s spi_write fail\n", __func__); + goto _error_locked; + } + + if (!use_no_irq) { + mutex_lock(&data->pending_lock); + list_add_tail(&msg->list, &data->pending_list); + mutex_unlock(&data->pending_lock); + } + + status = ssp_check_lines(data, true); + if (status < 0) { + if (!use_no_irq) { + mutex_lock(&data->pending_lock); + list_del(&msg->list); + mutex_unlock(&data->pending_lock); + } + goto _error_locked; + } + + mutex_unlock(&data->comm_lock); + + if (!use_no_irq && done) + if (wait_for_completion_timeout(done, + msecs_to_jiffies(timeout)) == + 0) { + mutex_lock(&data->pending_lock); + list_del(&msg->list); + mutex_unlock(&data->pending_lock); + + data->timeout_cnt++; + return -ETIMEDOUT; + } + + return 0; + +_error_locked: + mutex_unlock(&data->comm_lock); + data->timeout_cnt++; + return status; +} + +static inline int ssp_spi_sync_command(struct ssp_data *data, + struct ssp_msg *msg) +{ + return ssp_do_transfer(data, msg, NULL, 0); +} + +static int ssp_spi_sync(struct ssp_data *data, struct ssp_msg *msg, + int timeout) +{ + DECLARE_COMPLETION_ONSTACK(done); + + if (WARN_ON(!msg->length)) + return -EPERM; + + return ssp_do_transfer(data, msg, &done, timeout); +} + +static int ssp_handle_big_data(struct ssp_data *data, char *dataframe, int *idx) +{ + /* mock-up, it will be changed with adding another sensor types */ + *idx += 8; + return 0; +} + +static int ssp_parse_dataframe(struct ssp_data *data, char *dataframe, int len) +{ + int idx, sd; + struct timespec ts; + struct ssp_sensor_data *spd; + struct iio_dev **indio_devs = data->sensor_devs; + + getnstimeofday(&ts); + + for (idx = 0; idx < len;) { + switch (dataframe[idx++]) { + case SSP_MSG2AP_INST_BYPASS_DATA: + sd = dataframe[idx++]; + if (sd < 0 || sd >= SSP_SENSOR_MAX) { + dev_err(SSP_DEV, + "Mcu data frame1 error %d\n", sd); + return -EPROTO; + } + + if (indio_devs[sd]) { + spd = iio_priv(indio_devs[sd]); + if (spd->process_data) + spd->process_data(indio_devs[sd], + &dataframe[idx], + data->timestamp); + } else { + dev_err(SSP_DEV, "no client for frame\n"); + } + + idx += ssp_offset_map[sd]; + break; + case SSP_MSG2AP_INST_DEBUG_DATA: + sd = ssp_print_mcu_debug(dataframe, &idx, len); + if (sd) { + dev_err(SSP_DEV, + "Mcu data frame3 error %d\n", sd); + return sd; + } + break; + case SSP_MSG2AP_INST_LIBRARY_DATA: + idx += len; + break; + case SSP_MSG2AP_INST_BIG_DATA: + ssp_handle_big_data(data, dataframe, &idx); + break; + case SSP_MSG2AP_INST_TIME_SYNC: + data->time_syncing = true; + break; + case SSP_MSG2AP_INST_RESET: + ssp_queue_ssp_refresh_task(data, 0); + break; + } + } + + if (data->time_syncing) + data->timestamp = ts.tv_sec * 1000000000ULL + ts.tv_nsec; + + return 0; +} + +/* threaded irq */ +int ssp_irq_msg(struct ssp_data *data) +{ + bool found = false; + char *buffer; + u8 msg_type; + int ret; + u16 length, msg_options; + struct ssp_msg *msg, *n; + + ret = spi_read(data->spi, data->header_buffer, SSP_HEADER_BUFFER_SIZE); + if (ret < 0) { + dev_err(SSP_DEV, "header read fail\n"); + return ret; + } + + length = le16_to_cpu(data->header_buffer[1]); + msg_options = le16_to_cpu(data->header_buffer[0]); + + if (length == 0) { + dev_err(SSP_DEV, "length received from mcu is 0\n"); + return -EINVAL; + } + + msg_type = SSP_GET_MESSAGE_TYPE(msg_options); + + switch (msg_type) { + case SSP_AP2HUB_READ: + case SSP_AP2HUB_WRITE: + /* + * this is a small list, a few elements - the packets can be + * received with no order + */ + mutex_lock(&data->pending_lock); + list_for_each_entry_safe(msg, n, &data->pending_list, list) { + if (msg->options == msg_options) { + list_del(&msg->list); + found = true; + break; + } + } + + if (!found) { + /* + * here can be implemented dead messages handling + * but the slave should not send such ones - it is to + * check but let's handle this + */ + buffer = kmalloc(length, GFP_KERNEL | GFP_DMA); + if (!buffer) { + ret = -ENOMEM; + goto _unlock; + } + + /* got dead packet so it is always an error */ + ret = spi_read(data->spi, buffer, length); + if (ret >= 0) + ret = -EPROTO; + + kfree(buffer); + + dev_err(SSP_DEV, "No match error %x\n", + msg_options); + + goto _unlock; + } + + if (msg_type == SSP_AP2HUB_READ) + ret = spi_read(data->spi, + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], + msg->length); + + if (msg_type == SSP_AP2HUB_WRITE) { + ret = spi_write(data->spi, + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], + msg->length); + if (msg_options & SSP_AP2HUB_RETURN) { + msg->options = + SSP_AP2HUB_READ | SSP_AP2HUB_RETURN; + msg->length = 1; + + list_add_tail(&msg->list, &data->pending_list); + goto _unlock; + } + } + + if (msg->done) + if (!completion_done(msg->done)) + complete(msg->done); +_unlock: + mutex_unlock(&data->pending_lock); + break; + case SSP_HUB2AP_WRITE: + buffer = kzalloc(length, GFP_KERNEL | GFP_DMA); + if (!buffer) + return -ENOMEM; + + ret = spi_read(data->spi, buffer, length); + if (ret < 0) { + dev_err(SSP_DEV, "spi read fail\n"); + kfree(buffer); + break; + } + + ret = ssp_parse_dataframe(data, buffer, length); + + kfree(buffer); + break; + + default: + dev_err(SSP_DEV, "unknown msg type\n"); + return -EPROTO; + } + + return ret; +} + +void ssp_clean_pending_list(struct ssp_data *data) +{ + struct ssp_msg *msg, *n; + + mutex_lock(&data->pending_lock); + list_for_each_entry_safe(msg, n, &data->pending_list, list) { + list_del(&msg->list); + + if (msg->done) + if (!completion_done(msg->done)) + complete(msg->done); + } + mutex_unlock(&data->pending_lock); +} + +int ssp_command(struct ssp_data *data, char command, int arg) +{ + int ret; + struct ssp_msg *msg; + + msg = ssp_create_msg(command, 0, SSP_AP2HUB_WRITE, arg); + if (!msg) + return -ENOMEM; + + ssp_dbg("%s - command 0x%x %d\n", __func__, command, arg); + + ret = ssp_spi_sync_command(data, msg); + ssp_clean_msg(msg); + + return ret; +} + +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, + u8 *send_buf, u8 length) +{ + int ret; + struct ssp_msg *msg; + + if (data->fw_dl_state == SSP_FW_DL_STATE_DOWNLOADING) { + dev_err(SSP_DEV, "%s - Skip Inst! DL state = %d\n", + __func__, data->fw_dl_state); + return -EBUSY; + } else if (!(data->available_sensors & BIT(sensor_type)) && + (inst <= SSP_MSG2SSP_INST_CHANGE_DELAY)) { + dev_err(SSP_DEV, "%s - Bypass Inst Skip! - %u\n", + __func__, sensor_type); + return -EIO; /* just fail */ + } + + msg = ssp_create_msg(inst, length + 2, SSP_AP2HUB_WRITE, 0); + if (!msg) + return -ENOMEM; + + ssp_fill_buffer(msg, 0, &sensor_type, 1); + ssp_fill_buffer(msg, 1, send_buf, length); + + ssp_dbg("%s - Inst = 0x%x, Sensor Type = 0x%x, data = %u\n", + __func__, inst, sensor_type, send_buf[1]); + + ret = ssp_spi_sync(data, msg, 1000); + ssp_clean_msg(msg); + + return ret; +} + +int ssp_get_chipid(struct ssp_data *data) +{ + int ret; + char buffer; + struct ssp_msg *msg; + + msg = ssp_create_msg(SSP_MSG2SSP_AP_WHOAMI, 1, SSP_AP2HUB_READ, 0); + if (!msg) + return -ENOMEM; + + ret = ssp_spi_sync(data, msg, 1000); + + buffer = SSP_GET_BUFFER_AT_INDEX(msg, 0); + + ssp_clean_msg(msg); + + return ret < 0 ? ret : buffer; +} + +int ssp_set_magnetic_matrix(struct ssp_data *data) +{ + int ret; + struct ssp_msg *msg; + + msg = ssp_create_msg(SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX, + data->sensorhub_info->mag_length, SSP_AP2HUB_WRITE, + 0); + if (!msg) + return -ENOMEM; + + ssp_fill_buffer(msg, 0, data->sensorhub_info->mag_table, + data->sensorhub_info->mag_length); + + ret = ssp_spi_sync(data, msg, 1000); + ssp_clean_msg(msg); + + return ret; +} + +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data) +{ + int ret; + __le32 result; + u32 cpu_result = 0; + + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_SENSOR_SCANNING, 4, + SSP_AP2HUB_READ, 0); + if (!msg) + return 0; + + ret = ssp_spi_sync(data, msg, 1000); + if (ret < 0) { + dev_err(SSP_DEV, "%s - spi read fail %d\n", __func__, ret); + goto _exit; + } + + ssp_get_buffer(msg, 0, &result, 4); + cpu_result = le32_to_cpu(result); + + dev_info(SSP_DEV, "%s state: 0x%08x\n", __func__, cpu_result); + +_exit: + ssp_clean_msg(msg); + return cpu_result; +} + +unsigned int ssp_get_firmware_rev(struct ssp_data *data) +{ + int ret; + __le32 result; + + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_FIRMWARE_REV, 4, + SSP_AP2HUB_READ, 0); + if (!msg) + return SSP_INVALID_REVISION; + + ret = ssp_spi_sync(data, msg, 1000); + if (ret < 0) { + dev_err(SSP_DEV, "%s - transfer fail %d\n", __func__, ret); + ret = SSP_INVALID_REVISION; + goto _exit; + } + + ssp_get_buffer(msg, 0, &result, 4); + ret = le32_to_cpu(result); + +_exit: + ssp_clean_msg(msg); + return ret; +} diff --git a/include/linux/iio/common/ssp_sensors.h b/include/linux/iio/common/ssp_sensors.h new file mode 100644 index 0000000..f4d1b0e --- /dev/null +++ b/include/linux/iio/common/ssp_sensors.h @@ -0,0 +1,82 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ +#ifndef _SSP_SENSORS_H_ +#define _SSP_SENSORS_H_ + +#include <linux/iio/iio.h> + +#define SSP_TIME_SIZE 4 +#define SSP_ACCELEROMETER_SIZE 6 +#define SSP_GYROSCOPE_SIZE 6 +#define SSP_BIO_HRM_RAW_SIZE 8 +#define SSP_BIO_HRM_RAW_FAC_SIZE 36 +#define SSP_BIO_HRM_LIB_SIZE 8 + +/** + * enum ssp_sensor_type - SSP sensor type + */ +enum ssp_sensor_type { + SSP_ACCELEROMETER_SENSOR = 0, + SSP_GYROSCOPE_SENSOR, + SSP_GEOMAGNETIC_UNCALIB_SENSOR, + SSP_GEOMAGNETIC_RAW, + SSP_GEOMAGNETIC_SENSOR, + SSP_PRESSURE_SENSOR, + SSP_GESTURE_SENSOR, + SSP_PROXIMITY_SENSOR, + SSP_TEMPERATURE_HUMIDITY_SENSOR, + SSP_LIGHT_SENSOR, + SSP_PROXIMITY_RAW, + SSP_ORIENTATION_SENSOR, + SSP_STEP_DETECTOR, + SSP_SIG_MOTION_SENSOR, + SSP_GYRO_UNCALIB_SENSOR, + SSP_GAME_ROTATION_VECTOR, + SSP_ROTATION_VECTOR, + SSP_STEP_COUNTER, + SSP_BIO_HRM_RAW, + SSP_BIO_HRM_RAW_FAC, + SSP_BIO_HRM_LIB, + SSP_SENSOR_MAX, +}; + +struct ssp_data; + +/** + * struct ssp_sensor_data - Sensor object + * @process_data: Callback to feed sensor data. + * @type: Used sensor type. + * @buffer: Received data buffer. + */ +struct ssp_sensor_data { + int (*process_data)(struct iio_dev *indio_dev, void *buf, + int64_t timestamp); + enum ssp_sensor_type type; + u8 *buffer; +}; + +void ssp_register_consumer(struct iio_dev *indio_dev, + enum ssp_sensor_type type); + +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, + u32 delay); + +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type); + +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type); + +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, + u32 delay); +#endif /* _SSP_SENSORS_H_ */ -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v5 1/5] iio: common: ssp_sensors: Add sensorhub driver @ 2015-01-29 18:35 ` Jonathan Cameron 0 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:35 UTC (permalink / raw) To: Karol Wrona, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > Sensorhub is MCU dedicated to collect data and manage several sensors. > Sensorhub is a spi device which provides a layer for IIO devices. It provides > some data parsing and common mechanism for sensorhub sensors. > > Adds common sensorhub library for sensorhub driver and iio drivers > which uses sensorhub MCU to communicate with sensors. > > Signed-off-by: Karol Wrona <k.wrona@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> A couple of build errors from this one... I've fixed them up and applied to the togreg branch of iio.git. Pushed out as testing. If you get a chance to check I didn't mess anything up that would be great. > --- > drivers/iio/common/Kconfig | 1 + > drivers/iio/common/Makefile | 1 + > drivers/iio/common/ssp_sensors/Kconfig | 26 ++ > drivers/iio/common/ssp_sensors/Makefile | 8 + > drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++++++ > drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++++++++++++ > drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++++++++++ > include/linux/iio/common/ssp_sensors.h | 82 ++++ > 8 files changed, 1695 insertions(+) > create mode 100644 drivers/iio/common/ssp_sensors/Kconfig > create mode 100644 drivers/iio/common/ssp_sensors/Makefile > create mode 100644 drivers/iio/common/ssp_sensors/ssp.h > create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c > create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c > create mode 100644 include/linux/iio/common/ssp_sensors.h > > diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig > index 0b6e97d..790f106 100644 > --- a/drivers/iio/common/Kconfig > +++ b/drivers/iio/common/Kconfig > @@ -3,4 +3,5 @@ > # > > source "drivers/iio/common/hid-sensors/Kconfig" > +source "drivers/iio/common/ssp_sensors/Kconfig" > source "drivers/iio/common/st_sensors/Kconfig" > diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile > index 3112df0..b1e4d9c 100644 > --- a/drivers/iio/common/Makefile > +++ b/drivers/iio/common/Makefile > @@ -8,4 +8,5 @@ > > # When adding new entries keep the list in alphabetical order > obj-y += hid-sensors/ > +obj-y += ssp_sensors/ > obj-y += st_sensors/ > diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig > new file mode 100644 > index 0000000..0ea4faf > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/Kconfig > @@ -0,0 +1,26 @@ > +# > +# SSP sensor drivers and commons configuration > +# > +menu "SSP Sensor Common" > + > +config IIO_SSP_SENSORS_COMMONS > + tristate "Commons for all SSP Sensor IIO drivers" > + depends on IIO_SSP_SENSORHUB > + select IIO_BUFFER > + select IIO_KFIFO_BUF > + help > + Say yes here to build commons for SSP sensors. > + To compile this as a module, choose M here: the module > + will be called ssp_iio. > + > +config IIO_SSP_SENSORHUB > + tristate "Samsung Sensorhub driver" > + depends on SPI > + select MFD_CORE > + help > + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. > + To compile this driver as a module, choose M here: the > + module will be called sensorhub. > + > +endmenu > diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile > new file mode 100644 > index 0000000..1e0389e > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/Makefile > @@ -0,0 +1,8 @@ > +# > +# Makefile for SSP sensor drivers and commons. > +# > + > +sensorhub-objs := ssp_dev.o ssp_spi.o > +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o > + > +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_iio.o This file isn't in this patch. > diff --git a/drivers/iio/common/ssp_sensors/ssp.h b/drivers/iio/common/ssp_sensors/ssp.h > new file mode 100644 > index 0000000..b910e91 > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp.h > @@ -0,0 +1,257 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#ifndef __SSP_SENSORHUB_H__ > +#define __SSP_SENSORHUB_H__ > + > +#include <linux/delay.h> > +#include <linux/gpio.h> > +#include <linux/iio/common/ssp_sensors.h> > +#include <linux/iio/iio.h> > +#include <linux/spi/spi.h> > + > +#define SSP_DEVICE_ID 0x55 > + > +#ifdef SSP_DBG > +#define ssp_dbg(format, ...) pr_info("[SSP] "format, ##__VA_ARGS__) > +#else > +#define ssp_dbg(format, ...) > +#endif > + > +#define SSP_SW_RESET_TIME 3000 > +/* Sensor polling in ms */ > +#define SSP_DEFAULT_POLLING_DELAY 200 > +#define SSP_DEFAULT_RETRIES 3 > +#define SSP_DATA_PACKET_SIZE 960 > +#define SSP_HEADER_BUFFER_SIZE 4 > + > +enum { > + SSP_KERNEL_BINARY = 0, > + SSP_KERNEL_CRASHED_BINARY, > +}; > + > +enum { > + SSP_INITIALIZATION_STATE = 0, > + SSP_NO_SENSOR_STATE, > + SSP_ADD_SENSOR_STATE, > + SSP_RUNNING_SENSOR_STATE, > +}; > + > +/* Firmware download STATE */ > +enum { > + SSP_FW_DL_STATE_FAIL = -1, > + SSP_FW_DL_STATE_NONE = 0, > + SSP_FW_DL_STATE_NEED_TO_SCHEDULE, > + SSP_FW_DL_STATE_SCHEDULED, > + SSP_FW_DL_STATE_DOWNLOADING, > + SSP_FW_DL_STATE_SYNC, > + SSP_FW_DL_STATE_DONE, > +}; > + > +#define SSP_INVALID_REVISION 99999 > +#define SSP_INVALID_REVISION2 0xffffff > + > +/* AP -> SSP Instruction */ > +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD 0xa1 > +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_RM 0xa2 > +#define SSP_MSG2SSP_INST_REMOVE_ALL 0xa3 > +#define SSP_MSG2SSP_INST_CHANGE_DELAY 0xa4 > +#define SSP_MSG2SSP_INST_LIBRARY_ADD 0xb1 > +#define SSP_MSG2SSP_INST_LIBRARY_REMOVE 0xb2 > +#define SSP_MSG2SSP_INST_LIB_NOTI 0xb4 > +#define SSP_MSG2SSP_INST_LIB_DATA 0xc1 > + > +#define SSP_MSG2SSP_AP_MCU_SET_GYRO_CAL 0xcd > +#define SSP_MSG2SSP_AP_MCU_SET_ACCEL_CAL 0xce > +#define SSP_MSG2SSP_AP_STATUS_SHUTDOWN 0xd0 > +#define SSP_MSG2SSP_AP_STATUS_WAKEUP 0xd1 > +#define SSP_MSG2SSP_AP_STATUS_SLEEP 0xd2 > +#define SSP_MSG2SSP_AP_STATUS_RESUME 0xd3 > +#define SSP_MSG2SSP_AP_STATUS_SUSPEND 0xd4 > +#define SSP_MSG2SSP_AP_STATUS_RESET 0xd5 > +#define SSP_MSG2SSP_AP_STATUS_POW_CONNECTED 0xd6 > +#define SSP_MSG2SSP_AP_STATUS_POW_DISCONNECTED 0xd7 > +#define SSP_MSG2SSP_AP_TEMPHUMIDITY_CAL_DONE 0xda > +#define SSP_MSG2SSP_AP_MCU_SET_DUMPMODE 0xdb > +#define SSP_MSG2SSP_AP_MCU_DUMP_CHECK 0xdc > +#define SSP_MSG2SSP_AP_MCU_BATCH_FLUSH 0xdd > +#define SSP_MSG2SSP_AP_MCU_BATCH_COUNT 0xdf > + > +#define SSP_MSG2SSP_AP_WHOAMI 0x0f > +#define SSP_MSG2SSP_AP_FIRMWARE_REV 0xf0 > +#define SSP_MSG2SSP_AP_SENSOR_FORMATION 0xf1 > +#define SSP_MSG2SSP_AP_SENSOR_PROXTHRESHOLD 0xf2 > +#define SSP_MSG2SSP_AP_SENSOR_BARCODE_EMUL 0xf3 > +#define SSP_MSG2SSP_AP_SENSOR_SCANNING 0xf4 > +#define SSP_MSG2SSP_AP_SET_MAGNETIC_HWOFFSET 0xf5 > +#define SSP_MSG2SSP_AP_GET_MAGNETIC_HWOFFSET 0xf6 > +#define SSP_MSG2SSP_AP_SENSOR_GESTURE_CURRENT 0xf7 > +#define SSP_MSG2SSP_AP_GET_THERM 0xf8 > +#define SSP_MSG2SSP_AP_GET_BIG_DATA 0xf9 > +#define SSP_MSG2SSP_AP_SET_BIG_DATA 0xfa > +#define SSP_MSG2SSP_AP_START_BIG_DATA 0xfb > +#define SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX 0xfd > +#define SSP_MSG2SSP_AP_SENSOR_TILT 0xea > +#define SSP_MSG2SSP_AP_MCU_SET_TIME 0xfe > +#define SSP_MSG2SSP_AP_MCU_GET_TIME 0xff > + > +#define SSP_MSG2SSP_AP_FUSEROM 0x01 > + > +/* voice data */ > +#define SSP_TYPE_WAKE_UP_VOICE_SERVICE 0x01 > +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_AM 0x01 > +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_GRAMMER 0x02 > + > +/* Factory Test */ > +#define SSP_ACCELEROMETER_FACTORY 0x80 > +#define SSP_GYROSCOPE_FACTORY 0x81 > +#define SSP_GEOMAGNETIC_FACTORY 0x82 > +#define SSP_PRESSURE_FACTORY 0x85 > +#define SSP_GESTURE_FACTORY 0x86 > +#define SSP_TEMPHUMIDITY_CRC_FACTORY 0x88 > +#define SSP_GYROSCOPE_TEMP_FACTORY 0x8a > +#define SSP_GYROSCOPE_DPS_FACTORY 0x8b > +#define SSP_MCU_FACTORY 0x8c > +#define SSP_MCU_SLEEP_FACTORY 0x8d > + > +/* SSP -> AP ACK about write CMD */ > +#define SSP_MSG_ACK 0x80 /* ACK from SSP to AP */ > +#define SSP_MSG_NAK 0x70 /* NAK from SSP to AP */ > + > +struct ssp_sensorhub_info { > + char *fw_name; > + char *fw_crashed_name; > + unsigned int fw_rev; > + const u8 * const mag_table; > + const unsigned int mag_length; > +}; > + > +/* ssp_msg options bit */ > +#define SSP_RW 0 > +#define SSP_INDEX 3 > + > +#define SSP_AP2HUB_READ 0 > +#define SSP_AP2HUB_WRITE 1 > +#define SSP_HUB2AP_WRITE 2 > +#define SSP_AP2HUB_READY 3 > +#define SSP_AP2HUB_RETURN 4 > + > +/** > + * struct ssp_data - ssp platformdata structure > + * @spi: spi device > + * @sensorhub_info: info about sensorhub board specific features > + * @wdt_timer: watchdog timer > + * @work_wdt: watchdog work > + * @work_firmware: firmware upgrade work queue > + * @work_refresh: refresh work queue for reset request from MCU > + * @shut_down: shut down flag > + * @mcu_dump_mode: mcu dump mode for debug > + * @time_syncing: time syncing indication flag > + * @timestamp: previous time in ns calculated for time syncing > + * @check_status: status table for each sensor > + * @com_fail_cnt: communication fail count > + * @reset_cnt: reset count > + * @timeout_cnt: timeout count > + * @available_sensors: available sensors seen by sensorhub (bit array) > + * @cur_firm_rev: cached current firmware revision > + * @last_resume_state: last AP resume/suspend state used to handle the PM > + * state of ssp > + * @last_ap_state: (obsolete) sleep notification for MCU > + * @sensor_enable: sensor enable mask > + * @delay_buf: data acquisition intervals table > + * @batch_latency_buf: yet unknown but existing in communication protocol > + * @batch_opt_buf: yet unknown but existing in communication protocol > + * @accel_position: yet unknown but existing in communication protocol > + * @mag_position: yet unknown but existing in communication protocol > + * @fw_dl_state: firmware download state > + * @comm_lock: lock protecting the handshake > + * @pending_lock: lock protecting pending list and completion > + * @mcu_reset_gpio: mcu reset line > + * @ap_mcu_gpio: ap to mcu gpio line > + * @mcu_ap_gpio: mcu to ap gpio line > + * @pending_list: pending list for messages queued to be sent/read > + * @sensor_devs: registered IIO devices table > + * @enable_refcount: enable reference count for wdt (watchdog timer) > + * @header_buffer: cache aligned buffer for packet header > + */ > +struct ssp_data { > + struct spi_device *spi; > + struct ssp_sensorhub_info *sensorhub_info; > + struct timer_list wdt_timer; > + struct work_struct work_wdt; > + struct delayed_work work_refresh; > + > + bool shut_down; > + bool mcu_dump_mode; > + bool time_syncing; > + int64_t timestamp; > + > + int check_status[SSP_SENSOR_MAX]; > + > + unsigned int com_fail_cnt; > + unsigned int reset_cnt; > + unsigned int timeout_cnt; > + > + unsigned int available_sensors; > + unsigned int cur_firm_rev; > + > + char last_resume_state; > + char last_ap_state; > + > + unsigned int sensor_enable; > + u32 delay_buf[SSP_SENSOR_MAX]; > + s32 batch_latency_buf[SSP_SENSOR_MAX]; > + s8 batch_opt_buf[SSP_SENSOR_MAX]; > + > + int accel_position; > + int mag_position; > + int fw_dl_state; > + > + struct mutex comm_lock; > + struct mutex pending_lock; > + > + int mcu_reset_gpio; > + int ap_mcu_gpio; > + int mcu_ap_gpio; > + > + struct list_head pending_list; > + > + struct iio_dev *sensor_devs[SSP_SENSOR_MAX]; > + atomic_t enable_refcount; > + > + __le16 header_buffer[SSP_HEADER_BUFFER_SIZE / sizeof(__le16)] > + ____cacheline_aligned; > +}; > + > +void ssp_clean_pending_list(struct ssp_data *data); > + > +int ssp_command(struct ssp_data *data, char command, int arg); > + > +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, > + u8 *send_buf, u8 length); > + > +int ssp_irq_msg(struct ssp_data *data); > + > +int ssp_get_chipid(struct ssp_data *data); > + > +int ssp_set_magnetic_matrix(struct ssp_data *data); > + > +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data); > + > +unsigned int ssp_get_firmware_rev(struct ssp_data *data); > + > +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay); > + > +#endif /* __SSP_SENSORHUB_H__ */ > diff --git a/drivers/iio/common/ssp_sensors/ssp_dev.c b/drivers/iio/common/ssp_sensors/ssp_dev.c > new file mode 100644 > index 0000000..6b22115 > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_dev.c > @@ -0,0 +1,712 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/iio/iio.h> > +#include <linux/interrupt.h> > +#include <linux/io.h> > +#include <linux/mfd/core.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_gpio.h> > +#include <linux/of_platform.h> > +#include "ssp.h" > + > +#define SSP_WDT_TIME 10000 > +#define SSP_LIMIT_RESET_CNT 20 > +#define SSP_LIMIT_TIMEOUT_CNT 3 > + > +/* It is possible that it is max clk rate for version 1.0 of bootcode */ > +#define SSP_BOOT_SPI_HZ 400000 > + > +/* > + * These fields can look enigmatic but this structure is used mainly to flat > + * some values and depends on command type. > + */ > +struct ssp_instruction { > + __le32 a; > + __le32 b; > + u8 c; > +} __attribute__((__packed__)); > + > +static const u8 ssp_magnitude_table[] = {110, 85, 171, 71, 203, 195, 0, 67, > + 208, 56, 175, 244, 206, 213, 0, 92, 250, 0, 55, 48, 189, 252, 171, > + 243, 13, 45, 250}; > + > +static const struct ssp_sensorhub_info ssp_rinato_info = { > + .fw_name = "ssp_B2.fw", > + .fw_crashed_name = "ssp_crashed.fw", > + .fw_rev = 14052300, > + .mag_table = ssp_magnitude_table, > + .mag_length = ARRAY_SIZE(ssp_magnitude_table), > +}; > + > +static const struct ssp_sensorhub_info ssp_thermostat_info = { > + .fw_name = "thermostat_B2.fw", > + .fw_crashed_name = "ssp_crashed.fw", > + .fw_rev = 14080600, > + .mag_table = ssp_magnitude_table, > + .mag_length = ARRAY_SIZE(ssp_magnitude_table), > +}; > + > +static const struct mfd_cell sensorhub_sensor_devs[] = { > + { > + .name = "ssp-accelerometer", > + }, > + { > + .name = "ssp-gyroscope", > + }, > +}; > + > +static void ssp_toggle_mcu_reset_gpio(struct ssp_data *data) > +{ > + gpio_set_value(data->mcu_reset_gpio, 0); > + usleep_range(1000, 1200); > + gpio_set_value(data->mcu_reset_gpio, 1); > + msleep(50); > +} > + > +static void ssp_sync_available_sensors(struct ssp_data *data) > +{ > + int i, ret; > + > + for (i = 0; i < SSP_SENSOR_MAX; ++i) { > + if (data->available_sensors & BIT(i)) { > + ret = ssp_enable_sensor(data, i, data->delay_buf[i]); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "Sync sensor nr: %d fail\n", i); > + continue; > + } > + } > + } > + > + ret = ssp_command(data, SSP_MSG2SSP_AP_MCU_SET_DUMPMODE, > + data->mcu_dump_mode); > + if (ret < 0) > + dev_err(&data->spi->dev, > + "SSP_MSG2SSP_AP_MCU_SET_DUMPMODE failed\n"); > +} > + > +static void ssp_enable_mcu(struct ssp_data *data, bool enable) > +{ > + dev_info(&data->spi->dev, "current shutdown = %d, old = %d\n", enable, > + data->shut_down); > + > + if (enable && data->shut_down) { > + data->shut_down = false; > + enable_irq(data->spi->irq); > + enable_irq_wake(data->spi->irq); > + } else if (!enable && !data->shut_down) { > + data->shut_down = true; > + disable_irq(data->spi->irq); > + disable_irq_wake(data->spi->irq); > + } else { > + dev_warn(&data->spi->dev, "current shutdown = %d, old = %d\n", > + enable, data->shut_down); > + } > +} > + > +/* > + * This function is the first one which communicates with the mcu so it is > + * possible that the first attempt will fail > + */ > +static int ssp_check_fwbl(struct ssp_data *data) > +{ > + int retries = 0; > + > + while (retries++ < 5) { > + data->cur_firm_rev = ssp_get_firmware_rev(data); > + if (data->cur_firm_rev == SSP_INVALID_REVISION || > + data->cur_firm_rev == SSP_INVALID_REVISION2) { > + dev_warn(&data->spi->dev, > + "Invalid revision, trying %d time\n", retries); > + } else { > + break; > + } > + } > + > + if (data->cur_firm_rev == SSP_INVALID_REVISION || > + data->cur_firm_rev == SSP_INVALID_REVISION2) { > + dev_err(&data->spi->dev, "SSP_INVALID_REVISION\n"); > + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; > + } > + > + dev_info(&data->spi->dev, > + "MCU Firm Rev : Old = %8u, New = %8u\n", > + data->cur_firm_rev, > + data->sensorhub_info->fw_rev); > + > + if (data->cur_firm_rev != data->sensorhub_info->fw_rev) > + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; > + > + return SSP_FW_DL_STATE_NONE; > +} > + > +static void ssp_reset_mcu(struct ssp_data *data) > +{ > + ssp_enable_mcu(data, false); > + ssp_clean_pending_list(data); > + ssp_toggle_mcu_reset_gpio(data); > + ssp_enable_mcu(data, true); > +} > + > +static void ssp_wdt_work_func(struct work_struct *work) > +{ > + struct ssp_data *data = container_of(work, struct ssp_data, work_wdt); > + > + dev_err(&data->spi->dev, "%s - Sensor state: 0x%x, RC: %u, CC: %u\n", > + __func__, data->available_sensors, data->reset_cnt, > + data->com_fail_cnt); > + > + ssp_reset_mcu(data); > + data->com_fail_cnt = 0; > + data->timeout_cnt = 0; > +} > + > +static void ssp_wdt_timer_func(unsigned long ptr) > +{ > + struct ssp_data *data = (struct ssp_data *)ptr; > + > + switch (data->fw_dl_state) { > + case SSP_FW_DL_STATE_FAIL: > + case SSP_FW_DL_STATE_DOWNLOADING: > + case SSP_FW_DL_STATE_SYNC: > + goto _mod; > + } > + > + if (data->timeout_cnt > SSP_LIMIT_TIMEOUT_CNT || > + data->com_fail_cnt > SSP_LIMIT_RESET_CNT) > + queue_work(system_power_efficient_wq, &data->work_wdt); > +_mod: > + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); > +} > + > +static void ssp_enable_wdt_timer(struct ssp_data *data) > +{ > + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); > +} > + > +static void ssp_disable_wdt_timer(struct ssp_data *data) > +{ > + del_timer_sync(&data->wdt_timer); > + cancel_work_sync(&data->work_wdt); > +} > + > +/** > + * ssp_get_sensor_delay() - gets sensor data acquisition period > + * @data: sensorhub structure > + * @type: SSP sensor type > + * > + * Returns acquisition period in ms > + */ > +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type type) > +{ > + return data->delay_buf[type]; > +} > +EXPORT_SYMBOL(ssp_get_sensor_delay); > + > +/** > + * ssp_enable_sensor() - enables data acquisition for sensor > + * @data: sensorhub structure > + * @type: SSP sensor type > + * @delay: delay in ms > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay) > +{ > + int ret; > + struct ssp_instruction to_send; > + > + to_send.a = cpu_to_le32(delay); > + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); > + to_send.c = data->batch_opt_buf[type]; > + > + switch (data->check_status[type]) { > + case SSP_INITIALIZATION_STATE: > + /* do calibration step, now just enable */ > + case SSP_ADD_SENSOR_STATE: > + ret = ssp_send_instruction(data, > + SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD, > + type, > + (u8 *)&to_send, sizeof(to_send)); > + if (ret < 0) { > + dev_err(&data->spi->dev, "Enabling sensor failed\n"); > + data->check_status[type] = SSP_NO_SENSOR_STATE; > + goto derror; > + } > + > + data->sensor_enable |= BIT(type); > + data->check_status[type] = SSP_RUNNING_SENSOR_STATE; > + break; > + case SSP_RUNNING_SENSOR_STATE: > + ret = ssp_send_instruction(data, > + SSP_MSG2SSP_INST_CHANGE_DELAY, type, > + (u8 *)&to_send, sizeof(to_send)); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "Changing sensor delay failed\n"); > + goto derror; > + } > + break; > + default: > + data->check_status[type] = SSP_ADD_SENSOR_STATE; > + break; > + } > + > + data->delay_buf[type] = delay; > + > + if (atomic_inc_return(&data->enable_refcount) == 1) > + ssp_enable_wdt_timer(data); > + > + return 0; > + > +derror: > + return ret; > +} > +EXPORT_SYMBOL(ssp_enable_sensor); > + > +/** > + * ssp_change_delay() - changes data acquisition for sensor > + * @data: sensorhub structure > + * @type: SSP sensor type > + * @delay: delay in ms > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay) > +{ > + int ret; > + struct ssp_instruction to_send; > + > + to_send.a = cpu_to_le32(delay); > + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); > + to_send.c = data->batch_opt_buf[type]; > + > + ret = ssp_send_instruction(data, SSP_MSG2SSP_INST_CHANGE_DELAY, type, > + (u8 *)&to_send, sizeof(to_send)); > + if (ret < 0) { > + dev_err(&data->spi->dev, "Changing sensor delay failed\n"); > + return ret; > + } > + > + data->delay_buf[type] = delay; > + > + return 0; > +} > +EXPORT_SYMBOL(ssp_change_delay); > + > +/** > + * ssp_disable_sensor() - disables sensor > + * > + * @data: sensorhub structure > + * @type: SSP sensor type > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type) > +{ > + int ret; > + __le32 command; > + > + if (data->sensor_enable & BIT(type)) { > + command = cpu_to_le32(data->delay_buf[type]); > + > + ret = ssp_send_instruction(data, > + SSP_MSG2SSP_INST_BYPASS_SENSOR_RM, > + type, (u8 *)&command, > + sizeof(command)); > + if (ret < 0) { > + dev_err(&data->spi->dev, "Remove sensor fail\n"); > + return ret; > + } > + > + data->sensor_enable &= ~BIT(type); > + } > + > + data->check_status[type] = SSP_ADD_SENSOR_STATE; > + > + if (atomic_dec_and_test(&data->enable_refcount)) > + ssp_disable_wdt_timer(data); > + > + return 0; > +} > +EXPORT_SYMBOL(ssp_disable_sensor); > + > +static irqreturn_t ssp_irq_thread_fn(int irq, void *dev_id) > +{ > + struct ssp_data *data = dev_id; > + > + /* > + * This wrapper is done to preserve error path for ssp_irq_msg, also > + * it is defined in different file. > + */ > + ssp_irq_msg(data); > + > + return IRQ_HANDLED; > +} > + > +static int ssp_initialize_mcu(struct ssp_data *data) > +{ > + int ret; > + > + ssp_clean_pending_list(data); > + > + ret = ssp_get_chipid(data); > + if (ret != SSP_DEVICE_ID) { > + dev_err(&data->spi->dev, "%s - MCU %s ret = %d\n", __func__, > + ret < 0 ? "is not working" : "identification failed", > + ret); > + return ret < 0 ? ret : -ENODEV; > + } > + > + dev_info(&data->spi->dev, "MCU device ID = %d\n", ret); > + > + /* > + * needs clarification, for now do not want to export all transfer > + * methods to sensors' drivers > + */ > + ret = ssp_set_magnetic_matrix(data); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "%s - ssp_set_magnetic_matrix failed\n", __func__); > + return ret; > + } > + > + data->available_sensors = ssp_get_sensor_scanning_info(data); > + if (data->available_sensors == 0) { > + dev_err(&data->spi->dev, > + "%s - ssp_get_sensor_scanning_info failed\n", __func__); > + return -EIO; > + } > + > + data->cur_firm_rev = ssp_get_firmware_rev(data); > + dev_info(&data->spi->dev, "MCU Firm Rev : New = %8u\n", > + data->cur_firm_rev); > + > + return ssp_command(data, SSP_MSG2SSP_AP_MCU_DUMP_CHECK, 0); > +} > + > +/* > + * sensorhub can request its reinitialization as some brutal and rare error > + * handling. It can be requested from the MCU. > + */ > +static void ssp_refresh_task(struct work_struct *work) > +{ > + struct ssp_data *data = container_of((struct delayed_work *)work, > + struct ssp_data, work_refresh); > + > + dev_info(&data->spi->dev, "refreshing\n"); > + > + data->reset_cnt++; > + > + if (ssp_initialize_mcu(data) >= 0) { > + ssp_sync_available_sensors(data); > + if (data->last_ap_state != 0) > + ssp_command(data, data->last_ap_state, 0); > + > + if (data->last_resume_state != 0) > + ssp_command(data, data->last_resume_state, 0); > + > + data->timeout_cnt = 0; > + data->com_fail_cnt = 0; > + } > +} > + > +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay) > +{ > + cancel_delayed_work_sync(&data->work_refresh); > + > + return queue_delayed_work(system_power_efficient_wq, > + &data->work_refresh, > + msecs_to_jiffies(delay)); > +} > + > +#ifdef CONFIG_OF > +static struct of_device_id ssp_of_match[] = { > + { > + .compatible = "samsung,sensorhub-rinato", > + .data = &ssp_rinato_info, > + }, { > + .compatible = "samsung,sensorhub-thermostat", > + .data = &ssp_thermostat_info, > + }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, ssp_of_match); > + > +static struct ssp_data *ssp_parse_dt(struct device *dev) > +{ > + int ret; > + struct ssp_data *data; > + struct device_node *node = dev->of_node; > + const struct of_device_id *match; > + > + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); > + if (!data) > + return NULL; > + > + data->mcu_ap_gpio = of_get_named_gpio(node, "mcu-ap-gpios", 0); > + if (data->mcu_ap_gpio < 0) > + goto err_free_pd; > + > + data->ap_mcu_gpio = of_get_named_gpio(node, "ap-mcu-gpios", 0); > + if (data->ap_mcu_gpio < 0) > + goto err_free_pd; > + > + data->mcu_reset_gpio = of_get_named_gpio(node, "mcu-reset-gpios", 0); > + if (data->mcu_reset_gpio < 0) > + goto err_free_pd; > + > + ret = devm_gpio_request_one(dev, data->ap_mcu_gpio, GPIOF_OUT_INIT_HIGH, > + "ap-mcu-gpios"); > + if (ret) > + goto err_free_pd; > + > + ret = devm_gpio_request_one(dev, data->mcu_reset_gpio, > + GPIOF_OUT_INIT_HIGH, "mcu-reset-gpios"); > + if (ret) > + goto err_ap_mcu; > + > + match = of_match_node(ssp_of_match, node); > + if (!match) > + goto err_mcu_reset_gpio; > + > + data->sensorhub_info = (struct ssp_sensorhub_info *)match->data; > + > + dev_set_drvdata(dev, data); > + > + return data; > + > +err_mcu_reset_gpio: > + devm_gpio_free(dev, data->mcu_reset_gpio); > +err_ap_mcu: > + devm_gpio_free(dev, data->ap_mcu_gpio); > +err_free_pd: > + devm_kfree(dev, data); > + return NULL; > +} > +#else > +static struct ssp_data *ssp_parse_dt(struct platform_device *pdev) > +{ This has incorrect arguements.. So causes a build error. > + return NULL; > +} > +#endif > + > +/** > + * ssp_register_consumer() - registers iio consumer in ssp framework > + * > + * @indio_dev: consumer iio device > + * @type: ssp sensor type > + */ > +void ssp_register_consumer(struct iio_dev *indio_dev, enum ssp_sensor_type type) > +{ > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + data->sensor_devs[type] = indio_dev; > +} > +EXPORT_SYMBOL(ssp_register_consumer); > + > +static int ssp_probe(struct spi_device *spi) > +{ > + int ret, i; > + struct ssp_data *data; > + > + data = ssp_parse_dt(&spi->dev); > + if (!data) { > + dev_err(&spi->dev, "Failed to find platform data\n"); > + return -ENODEV; > + } > + > + ret = mfd_add_devices(&spi->dev, -1, sensorhub_sensor_devs, > + ARRAY_SIZE(sensorhub_sensor_devs), NULL, 0, NULL); > + if (ret < 0) { > + dev_err(&spi->dev, "mfd add devices fail\n"); > + return ret; > + } > + > + spi->mode = SPI_MODE_1; > + ret = spi_setup(spi); > + if (ret < 0) { > + dev_err(&spi->dev, "Failed to setup spi\n"); > + return ret; > + } > + > + data->fw_dl_state = SSP_FW_DL_STATE_NONE; > + data->spi = spi; > + spi_set_drvdata(spi, data); > + > + mutex_init(&data->comm_lock); > + > + for (i = 0; i < SSP_SENSOR_MAX; ++i) { > + data->delay_buf[i] = SSP_DEFAULT_POLLING_DELAY; > + data->batch_latency_buf[i] = 0; > + data->batch_opt_buf[i] = 0; > + data->check_status[i] = SSP_INITIALIZATION_STATE; > + } > + > + data->delay_buf[SSP_BIO_HRM_LIB] = 100; > + > + data->time_syncing = true; > + > + mutex_init(&data->pending_lock); > + INIT_LIST_HEAD(&data->pending_list); > + > + atomic_set(&data->enable_refcount, 0); > + > + INIT_WORK(&data->work_wdt, ssp_wdt_work_func); > + INIT_DELAYED_WORK(&data->work_refresh, ssp_refresh_task); > + > + setup_timer(&data->wdt_timer, ssp_wdt_timer_func, (unsigned long)data); > + > + ret = request_threaded_irq(data->spi->irq, NULL, > + ssp_irq_thread_fn, > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + "SSP_Int", data); > + if (ret < 0) { > + dev_err(&spi->dev, "Irq request fail\n"); > + goto err_setup_irq; > + } > + > + /* Let's start with enabled one so irq balance could be ok */ > + data->shut_down = false; > + > + /* just to avoid unbalanced irq set wake up */ > + enable_irq_wake(data->spi->irq); > + > + data->fw_dl_state = ssp_check_fwbl(data); > + if (data->fw_dl_state == SSP_FW_DL_STATE_NONE) { > + ret = ssp_initialize_mcu(data); > + if (ret < 0) { > + dev_err(&spi->dev, "Initialize_mcu failed\n"); > + goto err_read_reg; > + } > + } else { > + dev_err(&spi->dev, "Firmware version not supported\n"); > + ret = -EPERM; > + goto err_read_reg; > + } > + > + return 0; > + > +err_read_reg: > + free_irq(data->spi->irq, data); > +err_setup_irq: > + mutex_destroy(&data->pending_lock); > + mutex_destroy(&data->comm_lock); > + > + dev_err(&spi->dev, "Probe failed!\n"); > + > + return ret; > +} > + > +static int ssp_remove(struct spi_device *spi) > +{ > + struct ssp_data *data = spi_get_drvdata(spi); > + > + if (ssp_command(data, SSP_MSG2SSP_AP_STATUS_SHUTDOWN, 0) < 0) > + dev_err(&data->spi->dev, > + "SSP_MSG2SSP_AP_STATUS_SHUTDOWN failed\n"); > + > + ssp_enable_mcu(data, false); > + ssp_disable_wdt_timer(data); > + > + ssp_clean_pending_list(data); > + > + free_irq(data->spi->irq, data); > + > + del_timer_sync(&data->wdt_timer); > + cancel_work_sync(&data->work_wdt); > + > + mutex_destroy(&data->comm_lock); > + mutex_destroy(&data->pending_lock); > + > + mfd_remove_devices(&spi->dev); > + > + return 0; > +} > + > +static int ssp_suspend(struct device *dev) > +{ > + int ret; > + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); > + > + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_SUSPEND; > + > + if (atomic_read(&data->enable_refcount) > 0) > + ssp_disable_wdt_timer(data); > + > + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_SUSPEND, 0); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "%s SSP_MSG2SSP_AP_STATUS_SUSPEND failed\n", __func__); > + > + ssp_enable_wdt_timer(data); > + return ret; > + } > + > + data->time_syncing = false; > + disable_irq(data->spi->irq); > + > + return 0; > +} > + > +static int ssp_resume(struct device *dev) > +{ > + int ret; > + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); > + > + enable_irq(data->spi->irq); > + > + if (atomic_read(&data->enable_refcount) > 0) > + ssp_enable_wdt_timer(data); > + > + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_RESUME, 0); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "%s SSP_MSG2SSP_AP_STATUS_RESUME failed\n", __func__); > + ssp_disable_wdt_timer(data); > + return ret; > + } > + > + /* timesyncing is set by MCU */ > + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_RESUME; > + > + return 0; > +} > + > +static const struct dev_pm_ops ssp_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(ssp_suspend, ssp_resume) > +}; > + > +static struct spi_driver ssp_driver = { > + .probe = ssp_probe, > + .remove = ssp_remove, > + .driver = { > + .pm = &ssp_pm_ops, > + .bus = &spi_bus_type, > + .owner = THIS_MODULE, > + .of_match_table = of_match_ptr(ssp_of_match), > + .name = "sensorhub" > + }, > +}; > + > +module_spi_driver(ssp_driver); > + > +MODULE_DESCRIPTION("ssp sensorhub driver"); > +MODULE_AUTHOR("Samsung Electronics"); > +MODULE_LICENSE("GPL"); > diff --git a/drivers/iio/common/ssp_sensors/ssp_spi.c b/drivers/iio/common/ssp_sensors/ssp_spi.c > new file mode 100644 > index 0000000..704284a > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_spi.c > @@ -0,0 +1,608 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include "ssp.h" > + > +#define SSP_DEV (&data->spi->dev) > +#define SSP_GET_MESSAGE_TYPE(data) (data & (3 << SSP_RW)) > + > +/* > + * SSP -> AP Instruction > + * They tell what packet type can be expected. In the future there will > + * be less of them. BYPASS means common sensor packets with accel, gyro, > + * hrm etc. data. LIBRARY and META are mock-up's for now. > + */ > +#define SSP_MSG2AP_INST_BYPASS_DATA 0x37 > +#define SSP_MSG2AP_INST_LIBRARY_DATA 0x01 > +#define SSP_MSG2AP_INST_DEBUG_DATA 0x03 > +#define SSP_MSG2AP_INST_BIG_DATA 0x04 > +#define SSP_MSG2AP_INST_META_DATA 0x05 > +#define SSP_MSG2AP_INST_TIME_SYNC 0x06 > +#define SSP_MSG2AP_INST_RESET 0x07 > + > +#define SSP_UNIMPLEMENTED -1 > + > +struct ssp_msg_header { > + u8 cmd; > + __le16 length; > + __le16 options; > + __le32 data; > +} __attribute__((__packed__)); > + > +struct ssp_msg { > + u16 length; > + u16 options; > + struct list_head list; > + struct completion *done; > + struct ssp_msg_header *h; > + char *buffer; > +}; > + > +static const int ssp_offset_map[SSP_SENSOR_MAX] = { > + [SSP_ACCELEROMETER_SENSOR] = SSP_ACCELEROMETER_SIZE + > + SSP_TIME_SIZE, > + [SSP_GYROSCOPE_SENSOR] = SSP_GYROSCOPE_SIZE + > + SSP_TIME_SIZE, > + [SSP_GEOMAGNETIC_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GEOMAGNETIC_RAW] = SSP_UNIMPLEMENTED, > + [SSP_GEOMAGNETIC_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_PRESSURE_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GESTURE_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_PROXIMITY_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_TEMPERATURE_HUMIDITY_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_LIGHT_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_PROXIMITY_RAW] = SSP_UNIMPLEMENTED, > + [SSP_ORIENTATION_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_STEP_DETECTOR] = SSP_UNIMPLEMENTED, > + [SSP_SIG_MOTION_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GYRO_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GAME_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, > + [SSP_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, > + [SSP_STEP_COUNTER] = SSP_UNIMPLEMENTED, > + [SSP_BIO_HRM_RAW] = SSP_BIO_HRM_RAW_SIZE + > + SSP_TIME_SIZE, > + [SSP_BIO_HRM_RAW_FAC] = SSP_BIO_HRM_RAW_FAC_SIZE + > + SSP_TIME_SIZE, > + [SSP_BIO_HRM_LIB] = SSP_BIO_HRM_LIB_SIZE + > + SSP_TIME_SIZE, > +}; > + > +#define SSP_HEADER_SIZE (sizeof(struct ssp_msg_header)) > +#define SSP_HEADER_SIZE_ALIGNED (ALIGN(SSP_HEADER_SIZE, 4)) > + > +static struct ssp_msg *ssp_create_msg(u8 cmd, u16 len, u16 opt, u32 data) > +{ > + struct ssp_msg_header h; > + struct ssp_msg *msg; > + > + msg = kzalloc(sizeof(*msg), GFP_KERNEL); > + if (!msg) > + return NULL; > + > + h.cmd = cmd; > + h.length = cpu_to_le16(len); > + h.options = cpu_to_le16(opt); > + h.data = cpu_to_le32(data); > + > + msg->buffer = kzalloc(SSP_HEADER_SIZE_ALIGNED + len, > + GFP_KERNEL | GFP_DMA); > + if (!msg->buffer) { > + kfree(msg); > + return NULL; > + } > + > + msg->length = len; > + msg->options = opt; > + > + memcpy(msg->buffer, &h, SSP_HEADER_SIZE); > + > + return msg; > +} > + > +/* > + * It is a bit heavy to do it this way but often the function is used to compose > + * the message from smaller chunks which are placed on the stack. Often the > + * chunks are small so memcpy should be optimalized. > + */ > +static inline void ssp_fill_buffer(struct ssp_msg *m, unsigned int offset, > + const void *src, unsigned int len) > +{ > + memcpy(&m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], src, len); > +} > + > +static inline void ssp_get_buffer(struct ssp_msg *m, unsigned int offset, > + void *dest, unsigned int len) > +{ > + memcpy(dest, &m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], len); > +} > + > +#define SSP_GET_BUFFER_AT_INDEX(m, index) \ > + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index]) > +#define SSP_SET_BUFFER_AT_INDEX(m, index, val) \ > + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index] = val) > + > +static void ssp_clean_msg(struct ssp_msg *m) > +{ > + kfree(m->buffer); > + kfree(m); > +} > + > +static int ssp_print_mcu_debug(char *data_frame, int *data_index, > + int received_len) > +{ > + int length = data_frame[(*data_index)++]; > + > + if (length > received_len - *data_index || length <= 0) { > + ssp_dbg("[SSP]: MSG From MCU-invalid debug length(%d/%d)\n", > + length, received_len); > + return length ? length : -EPROTO; > + } > + > + ssp_dbg("[SSP]: MSG From MCU - %s\n", &data_frame[*data_index]); > + > + *data_index += length; > + > + return 0; > +} > + > +/* > + * It was designed that way - additional lines to some kind of handshake, > + * please do not ask why - only the firmware guy can know it. > + */ > +static int ssp_check_lines(struct ssp_data *data, bool state) > +{ > + int delay_cnt = 0; > + > + gpio_set_value_cansleep(data->ap_mcu_gpio, state); > + > + while (gpio_get_value_cansleep(data->mcu_ap_gpio) != state) { > + usleep_range(3000, 3500); > + > + if (data->shut_down || delay_cnt++ > 500) { > + dev_err(SSP_DEV, "%s:timeout, hw ack wait fail %d\n", > + __func__, state); > + > + if (!state) > + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); > + > + return -ETIMEDOUT; > + } > + } > + > + return 0; > +} > + > +static int ssp_do_transfer(struct ssp_data *data, struct ssp_msg *msg, > + struct completion *done, int timeout) > +{ > + int status; > + /* > + * check if this is a short one way message or the whole transfer has > + * second part after an interrupt > + */ > + const bool use_no_irq = msg->length == 0; > + > + if (data->shut_down) > + return -EPERM; > + > + msg->done = done; > + > + mutex_lock(&data->comm_lock); > + > + status = ssp_check_lines(data, false); > + if (status < 0) > + goto _error_locked; > + > + status = spi_write(data->spi, msg->buffer, SSP_HEADER_SIZE); > + if (status < 0) { > + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); > + dev_err(SSP_DEV, "%s spi_write fail\n", __func__); > + goto _error_locked; > + } > + > + if (!use_no_irq) { > + mutex_lock(&data->pending_lock); > + list_add_tail(&msg->list, &data->pending_list); > + mutex_unlock(&data->pending_lock); > + } > + > + status = ssp_check_lines(data, true); > + if (status < 0) { > + if (!use_no_irq) { > + mutex_lock(&data->pending_lock); > + list_del(&msg->list); > + mutex_unlock(&data->pending_lock); > + } > + goto _error_locked; > + } > + > + mutex_unlock(&data->comm_lock); > + > + if (!use_no_irq && done) > + if (wait_for_completion_timeout(done, > + msecs_to_jiffies(timeout)) == > + 0) { > + mutex_lock(&data->pending_lock); > + list_del(&msg->list); > + mutex_unlock(&data->pending_lock); > + > + data->timeout_cnt++; > + return -ETIMEDOUT; > + } > + > + return 0; > + > +_error_locked: > + mutex_unlock(&data->comm_lock); > + data->timeout_cnt++; > + return status; > +} > + > +static inline int ssp_spi_sync_command(struct ssp_data *data, > + struct ssp_msg *msg) > +{ > + return ssp_do_transfer(data, msg, NULL, 0); > +} > + > +static int ssp_spi_sync(struct ssp_data *data, struct ssp_msg *msg, > + int timeout) > +{ > + DECLARE_COMPLETION_ONSTACK(done); > + > + if (WARN_ON(!msg->length)) > + return -EPERM; > + > + return ssp_do_transfer(data, msg, &done, timeout); > +} > + > +static int ssp_handle_big_data(struct ssp_data *data, char *dataframe, int *idx) > +{ > + /* mock-up, it will be changed with adding another sensor types */ > + *idx += 8; > + return 0; > +} > + > +static int ssp_parse_dataframe(struct ssp_data *data, char *dataframe, int len) > +{ > + int idx, sd; > + struct timespec ts; > + struct ssp_sensor_data *spd; > + struct iio_dev **indio_devs = data->sensor_devs; > + > + getnstimeofday(&ts); > + > + for (idx = 0; idx < len;) { > + switch (dataframe[idx++]) { > + case SSP_MSG2AP_INST_BYPASS_DATA: > + sd = dataframe[idx++]; > + if (sd < 0 || sd >= SSP_SENSOR_MAX) { > + dev_err(SSP_DEV, > + "Mcu data frame1 error %d\n", sd); > + return -EPROTO; > + } > + > + if (indio_devs[sd]) { > + spd = iio_priv(indio_devs[sd]); > + if (spd->process_data) > + spd->process_data(indio_devs[sd], > + &dataframe[idx], > + data->timestamp); > + } else { > + dev_err(SSP_DEV, "no client for frame\n"); > + } > + > + idx += ssp_offset_map[sd]; > + break; > + case SSP_MSG2AP_INST_DEBUG_DATA: > + sd = ssp_print_mcu_debug(dataframe, &idx, len); > + if (sd) { > + dev_err(SSP_DEV, > + "Mcu data frame3 error %d\n", sd); > + return sd; > + } > + break; > + case SSP_MSG2AP_INST_LIBRARY_DATA: > + idx += len; > + break; > + case SSP_MSG2AP_INST_BIG_DATA: > + ssp_handle_big_data(data, dataframe, &idx); > + break; > + case SSP_MSG2AP_INST_TIME_SYNC: > + data->time_syncing = true; > + break; > + case SSP_MSG2AP_INST_RESET: > + ssp_queue_ssp_refresh_task(data, 0); > + break; > + } > + } > + > + if (data->time_syncing) > + data->timestamp = ts.tv_sec * 1000000000ULL + ts.tv_nsec; > + > + return 0; > +} > + > +/* threaded irq */ > +int ssp_irq_msg(struct ssp_data *data) > +{ > + bool found = false; > + char *buffer; > + u8 msg_type; > + int ret; > + u16 length, msg_options; > + struct ssp_msg *msg, *n; > + > + ret = spi_read(data->spi, data->header_buffer, SSP_HEADER_BUFFER_SIZE); > + if (ret < 0) { > + dev_err(SSP_DEV, "header read fail\n"); > + return ret; > + } > + > + length = le16_to_cpu(data->header_buffer[1]); > + msg_options = le16_to_cpu(data->header_buffer[0]); > + > + if (length == 0) { > + dev_err(SSP_DEV, "length received from mcu is 0\n"); > + return -EINVAL; > + } > + > + msg_type = SSP_GET_MESSAGE_TYPE(msg_options); > + > + switch (msg_type) { > + case SSP_AP2HUB_READ: > + case SSP_AP2HUB_WRITE: > + /* > + * this is a small list, a few elements - the packets can be > + * received with no order > + */ > + mutex_lock(&data->pending_lock); > + list_for_each_entry_safe(msg, n, &data->pending_list, list) { > + if (msg->options == msg_options) { > + list_del(&msg->list); > + found = true; > + break; > + } > + } > + > + if (!found) { > + /* > + * here can be implemented dead messages handling > + * but the slave should not send such ones - it is to > + * check but let's handle this > + */ > + buffer = kmalloc(length, GFP_KERNEL | GFP_DMA); > + if (!buffer) { > + ret = -ENOMEM; > + goto _unlock; > + } > + > + /* got dead packet so it is always an error */ > + ret = spi_read(data->spi, buffer, length); > + if (ret >= 0) > + ret = -EPROTO; > + > + kfree(buffer); > + > + dev_err(SSP_DEV, "No match error %x\n", > + msg_options); > + > + goto _unlock; > + } > + > + if (msg_type == SSP_AP2HUB_READ) > + ret = spi_read(data->spi, > + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], > + msg->length); > + > + if (msg_type == SSP_AP2HUB_WRITE) { > + ret = spi_write(data->spi, > + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], > + msg->length); > + if (msg_options & SSP_AP2HUB_RETURN) { > + msg->options = > + SSP_AP2HUB_READ | SSP_AP2HUB_RETURN; > + msg->length = 1; > + > + list_add_tail(&msg->list, &data->pending_list); > + goto _unlock; > + } > + } > + > + if (msg->done) > + if (!completion_done(msg->done)) > + complete(msg->done); > +_unlock: > + mutex_unlock(&data->pending_lock); > + break; > + case SSP_HUB2AP_WRITE: > + buffer = kzalloc(length, GFP_KERNEL | GFP_DMA); > + if (!buffer) > + return -ENOMEM; > + > + ret = spi_read(data->spi, buffer, length); > + if (ret < 0) { > + dev_err(SSP_DEV, "spi read fail\n"); > + kfree(buffer); > + break; > + } > + > + ret = ssp_parse_dataframe(data, buffer, length); > + > + kfree(buffer); > + break; > + > + default: > + dev_err(SSP_DEV, "unknown msg type\n"); > + return -EPROTO; > + } > + > + return ret; > +} > + > +void ssp_clean_pending_list(struct ssp_data *data) > +{ > + struct ssp_msg *msg, *n; > + > + mutex_lock(&data->pending_lock); > + list_for_each_entry_safe(msg, n, &data->pending_list, list) { > + list_del(&msg->list); > + > + if (msg->done) > + if (!completion_done(msg->done)) > + complete(msg->done); > + } > + mutex_unlock(&data->pending_lock); > +} > + > +int ssp_command(struct ssp_data *data, char command, int arg) > +{ > + int ret; > + struct ssp_msg *msg; > + > + msg = ssp_create_msg(command, 0, SSP_AP2HUB_WRITE, arg); > + if (!msg) > + return -ENOMEM; > + > + ssp_dbg("%s - command 0x%x %d\n", __func__, command, arg); > + > + ret = ssp_spi_sync_command(data, msg); > + ssp_clean_msg(msg); > + > + return ret; > +} > + > +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, > + u8 *send_buf, u8 length) > +{ > + int ret; > + struct ssp_msg *msg; > + > + if (data->fw_dl_state == SSP_FW_DL_STATE_DOWNLOADING) { > + dev_err(SSP_DEV, "%s - Skip Inst! DL state = %d\n", > + __func__, data->fw_dl_state); > + return -EBUSY; > + } else if (!(data->available_sensors & BIT(sensor_type)) && > + (inst <= SSP_MSG2SSP_INST_CHANGE_DELAY)) { > + dev_err(SSP_DEV, "%s - Bypass Inst Skip! - %u\n", > + __func__, sensor_type); > + return -EIO; /* just fail */ > + } > + > + msg = ssp_create_msg(inst, length + 2, SSP_AP2HUB_WRITE, 0); > + if (!msg) > + return -ENOMEM; > + > + ssp_fill_buffer(msg, 0, &sensor_type, 1); > + ssp_fill_buffer(msg, 1, send_buf, length); > + > + ssp_dbg("%s - Inst = 0x%x, Sensor Type = 0x%x, data = %u\n", > + __func__, inst, sensor_type, send_buf[1]); > + > + ret = ssp_spi_sync(data, msg, 1000); > + ssp_clean_msg(msg); > + > + return ret; > +} > + > +int ssp_get_chipid(struct ssp_data *data) > +{ > + int ret; > + char buffer; > + struct ssp_msg *msg; > + > + msg = ssp_create_msg(SSP_MSG2SSP_AP_WHOAMI, 1, SSP_AP2HUB_READ, 0); > + if (!msg) > + return -ENOMEM; > + > + ret = ssp_spi_sync(data, msg, 1000); > + > + buffer = SSP_GET_BUFFER_AT_INDEX(msg, 0); > + > + ssp_clean_msg(msg); > + > + return ret < 0 ? ret : buffer; > +} > + > +int ssp_set_magnetic_matrix(struct ssp_data *data) > +{ > + int ret; > + struct ssp_msg *msg; > + > + msg = ssp_create_msg(SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX, > + data->sensorhub_info->mag_length, SSP_AP2HUB_WRITE, > + 0); > + if (!msg) > + return -ENOMEM; > + > + ssp_fill_buffer(msg, 0, data->sensorhub_info->mag_table, > + data->sensorhub_info->mag_length); > + > + ret = ssp_spi_sync(data, msg, 1000); > + ssp_clean_msg(msg); > + > + return ret; > +} > + > +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data) > +{ > + int ret; > + __le32 result; > + u32 cpu_result = 0; > + > + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_SENSOR_SCANNING, 4, > + SSP_AP2HUB_READ, 0); > + if (!msg) > + return 0; > + > + ret = ssp_spi_sync(data, msg, 1000); > + if (ret < 0) { > + dev_err(SSP_DEV, "%s - spi read fail %d\n", __func__, ret); > + goto _exit; > + } > + > + ssp_get_buffer(msg, 0, &result, 4); > + cpu_result = le32_to_cpu(result); > + > + dev_info(SSP_DEV, "%s state: 0x%08x\n", __func__, cpu_result); > + > +_exit: > + ssp_clean_msg(msg); > + return cpu_result; > +} > + > +unsigned int ssp_get_firmware_rev(struct ssp_data *data) > +{ > + int ret; > + __le32 result; > + > + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_FIRMWARE_REV, 4, > + SSP_AP2HUB_READ, 0); > + if (!msg) > + return SSP_INVALID_REVISION; > + > + ret = ssp_spi_sync(data, msg, 1000); > + if (ret < 0) { > + dev_err(SSP_DEV, "%s - transfer fail %d\n", __func__, ret); > + ret = SSP_INVALID_REVISION; > + goto _exit; > + } > + > + ssp_get_buffer(msg, 0, &result, 4); > + ret = le32_to_cpu(result); > + > +_exit: > + ssp_clean_msg(msg); > + return ret; > +} > diff --git a/include/linux/iio/common/ssp_sensors.h b/include/linux/iio/common/ssp_sensors.h > new file mode 100644 > index 0000000..f4d1b0e > --- /dev/null > +++ b/include/linux/iio/common/ssp_sensors.h > @@ -0,0 +1,82 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > +#ifndef _SSP_SENSORS_H_ > +#define _SSP_SENSORS_H_ > + > +#include <linux/iio/iio.h> > + > +#define SSP_TIME_SIZE 4 > +#define SSP_ACCELEROMETER_SIZE 6 > +#define SSP_GYROSCOPE_SIZE 6 > +#define SSP_BIO_HRM_RAW_SIZE 8 > +#define SSP_BIO_HRM_RAW_FAC_SIZE 36 > +#define SSP_BIO_HRM_LIB_SIZE 8 > + > +/** > + * enum ssp_sensor_type - SSP sensor type > + */ > +enum ssp_sensor_type { > + SSP_ACCELEROMETER_SENSOR = 0, > + SSP_GYROSCOPE_SENSOR, > + SSP_GEOMAGNETIC_UNCALIB_SENSOR, > + SSP_GEOMAGNETIC_RAW, > + SSP_GEOMAGNETIC_SENSOR, > + SSP_PRESSURE_SENSOR, > + SSP_GESTURE_SENSOR, > + SSP_PROXIMITY_SENSOR, > + SSP_TEMPERATURE_HUMIDITY_SENSOR, > + SSP_LIGHT_SENSOR, > + SSP_PROXIMITY_RAW, > + SSP_ORIENTATION_SENSOR, > + SSP_STEP_DETECTOR, > + SSP_SIG_MOTION_SENSOR, > + SSP_GYRO_UNCALIB_SENSOR, > + SSP_GAME_ROTATION_VECTOR, > + SSP_ROTATION_VECTOR, > + SSP_STEP_COUNTER, > + SSP_BIO_HRM_RAW, > + SSP_BIO_HRM_RAW_FAC, > + SSP_BIO_HRM_LIB, > + SSP_SENSOR_MAX, > +}; > + > +struct ssp_data; > + > +/** > + * struct ssp_sensor_data - Sensor object > + * @process_data: Callback to feed sensor data. > + * @type: Used sensor type. > + * @buffer: Received data buffer. > + */ > +struct ssp_sensor_data { > + int (*process_data)(struct iio_dev *indio_dev, void *buf, > + int64_t timestamp); > + enum ssp_sensor_type type; > + u8 *buffer; > +}; > + > +void ssp_register_consumer(struct iio_dev *indio_dev, > + enum ssp_sensor_type type); > + > +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay); > + > +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type); > + > +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type); > + > +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay); > +#endif /* _SSP_SENSORS_H_ */ > ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v5 1/5] iio: common: ssp_sensors: Add sensorhub driver @ 2015-01-29 18:35 ` Jonathan Cameron 0 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:35 UTC (permalink / raw) To: Karol Wrona, linux-iio-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > Sensorhub is MCU dedicated to collect data and manage several sensors. > Sensorhub is a spi device which provides a layer for IIO devices. It provides > some data parsing and common mechanism for sensorhub sensors. > > Adds common sensorhub library for sensorhub driver and iio drivers > which uses sensorhub MCU to communicate with sensors. > > Signed-off-by: Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> > Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> A couple of build errors from this one... I've fixed them up and applied to the togreg branch of iio.git. Pushed out as testing. If you get a chance to check I didn't mess anything up that would be great. > --- > drivers/iio/common/Kconfig | 1 + > drivers/iio/common/Makefile | 1 + > drivers/iio/common/ssp_sensors/Kconfig | 26 ++ > drivers/iio/common/ssp_sensors/Makefile | 8 + > drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++++++ > drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++++++++++++ > drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++++++++++ > include/linux/iio/common/ssp_sensors.h | 82 ++++ > 8 files changed, 1695 insertions(+) > create mode 100644 drivers/iio/common/ssp_sensors/Kconfig > create mode 100644 drivers/iio/common/ssp_sensors/Makefile > create mode 100644 drivers/iio/common/ssp_sensors/ssp.h > create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c > create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c > create mode 100644 include/linux/iio/common/ssp_sensors.h > > diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig > index 0b6e97d..790f106 100644 > --- a/drivers/iio/common/Kconfig > +++ b/drivers/iio/common/Kconfig > @@ -3,4 +3,5 @@ > # > > source "drivers/iio/common/hid-sensors/Kconfig" > +source "drivers/iio/common/ssp_sensors/Kconfig" > source "drivers/iio/common/st_sensors/Kconfig" > diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile > index 3112df0..b1e4d9c 100644 > --- a/drivers/iio/common/Makefile > +++ b/drivers/iio/common/Makefile > @@ -8,4 +8,5 @@ > > # When adding new entries keep the list in alphabetical order > obj-y += hid-sensors/ > +obj-y += ssp_sensors/ > obj-y += st_sensors/ > diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig > new file mode 100644 > index 0000000..0ea4faf > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/Kconfig > @@ -0,0 +1,26 @@ > +# > +# SSP sensor drivers and commons configuration > +# > +menu "SSP Sensor Common" > + > +config IIO_SSP_SENSORS_COMMONS > + tristate "Commons for all SSP Sensor IIO drivers" > + depends on IIO_SSP_SENSORHUB > + select IIO_BUFFER > + select IIO_KFIFO_BUF > + help > + Say yes here to build commons for SSP sensors. > + To compile this as a module, choose M here: the module > + will be called ssp_iio. > + > +config IIO_SSP_SENSORHUB > + tristate "Samsung Sensorhub driver" > + depends on SPI > + select MFD_CORE > + help > + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. > + To compile this driver as a module, choose M here: the > + module will be called sensorhub. > + > +endmenu > diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile > new file mode 100644 > index 0000000..1e0389e > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/Makefile > @@ -0,0 +1,8 @@ > +# > +# Makefile for SSP sensor drivers and commons. > +# > + > +sensorhub-objs := ssp_dev.o ssp_spi.o > +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o > + > +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_iio.o This file isn't in this patch. > diff --git a/drivers/iio/common/ssp_sensors/ssp.h b/drivers/iio/common/ssp_sensors/ssp.h > new file mode 100644 > index 0000000..b910e91 > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp.h > @@ -0,0 +1,257 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#ifndef __SSP_SENSORHUB_H__ > +#define __SSP_SENSORHUB_H__ > + > +#include <linux/delay.h> > +#include <linux/gpio.h> > +#include <linux/iio/common/ssp_sensors.h> > +#include <linux/iio/iio.h> > +#include <linux/spi/spi.h> > + > +#define SSP_DEVICE_ID 0x55 > + > +#ifdef SSP_DBG > +#define ssp_dbg(format, ...) pr_info("[SSP] "format, ##__VA_ARGS__) > +#else > +#define ssp_dbg(format, ...) > +#endif > + > +#define SSP_SW_RESET_TIME 3000 > +/* Sensor polling in ms */ > +#define SSP_DEFAULT_POLLING_DELAY 200 > +#define SSP_DEFAULT_RETRIES 3 > +#define SSP_DATA_PACKET_SIZE 960 > +#define SSP_HEADER_BUFFER_SIZE 4 > + > +enum { > + SSP_KERNEL_BINARY = 0, > + SSP_KERNEL_CRASHED_BINARY, > +}; > + > +enum { > + SSP_INITIALIZATION_STATE = 0, > + SSP_NO_SENSOR_STATE, > + SSP_ADD_SENSOR_STATE, > + SSP_RUNNING_SENSOR_STATE, > +}; > + > +/* Firmware download STATE */ > +enum { > + SSP_FW_DL_STATE_FAIL = -1, > + SSP_FW_DL_STATE_NONE = 0, > + SSP_FW_DL_STATE_NEED_TO_SCHEDULE, > + SSP_FW_DL_STATE_SCHEDULED, > + SSP_FW_DL_STATE_DOWNLOADING, > + SSP_FW_DL_STATE_SYNC, > + SSP_FW_DL_STATE_DONE, > +}; > + > +#define SSP_INVALID_REVISION 99999 > +#define SSP_INVALID_REVISION2 0xffffff > + > +/* AP -> SSP Instruction */ > +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD 0xa1 > +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_RM 0xa2 > +#define SSP_MSG2SSP_INST_REMOVE_ALL 0xa3 > +#define SSP_MSG2SSP_INST_CHANGE_DELAY 0xa4 > +#define SSP_MSG2SSP_INST_LIBRARY_ADD 0xb1 > +#define SSP_MSG2SSP_INST_LIBRARY_REMOVE 0xb2 > +#define SSP_MSG2SSP_INST_LIB_NOTI 0xb4 > +#define SSP_MSG2SSP_INST_LIB_DATA 0xc1 > + > +#define SSP_MSG2SSP_AP_MCU_SET_GYRO_CAL 0xcd > +#define SSP_MSG2SSP_AP_MCU_SET_ACCEL_CAL 0xce > +#define SSP_MSG2SSP_AP_STATUS_SHUTDOWN 0xd0 > +#define SSP_MSG2SSP_AP_STATUS_WAKEUP 0xd1 > +#define SSP_MSG2SSP_AP_STATUS_SLEEP 0xd2 > +#define SSP_MSG2SSP_AP_STATUS_RESUME 0xd3 > +#define SSP_MSG2SSP_AP_STATUS_SUSPEND 0xd4 > +#define SSP_MSG2SSP_AP_STATUS_RESET 0xd5 > +#define SSP_MSG2SSP_AP_STATUS_POW_CONNECTED 0xd6 > +#define SSP_MSG2SSP_AP_STATUS_POW_DISCONNECTED 0xd7 > +#define SSP_MSG2SSP_AP_TEMPHUMIDITY_CAL_DONE 0xda > +#define SSP_MSG2SSP_AP_MCU_SET_DUMPMODE 0xdb > +#define SSP_MSG2SSP_AP_MCU_DUMP_CHECK 0xdc > +#define SSP_MSG2SSP_AP_MCU_BATCH_FLUSH 0xdd > +#define SSP_MSG2SSP_AP_MCU_BATCH_COUNT 0xdf > + > +#define SSP_MSG2SSP_AP_WHOAMI 0x0f > +#define SSP_MSG2SSP_AP_FIRMWARE_REV 0xf0 > +#define SSP_MSG2SSP_AP_SENSOR_FORMATION 0xf1 > +#define SSP_MSG2SSP_AP_SENSOR_PROXTHRESHOLD 0xf2 > +#define SSP_MSG2SSP_AP_SENSOR_BARCODE_EMUL 0xf3 > +#define SSP_MSG2SSP_AP_SENSOR_SCANNING 0xf4 > +#define SSP_MSG2SSP_AP_SET_MAGNETIC_HWOFFSET 0xf5 > +#define SSP_MSG2SSP_AP_GET_MAGNETIC_HWOFFSET 0xf6 > +#define SSP_MSG2SSP_AP_SENSOR_GESTURE_CURRENT 0xf7 > +#define SSP_MSG2SSP_AP_GET_THERM 0xf8 > +#define SSP_MSG2SSP_AP_GET_BIG_DATA 0xf9 > +#define SSP_MSG2SSP_AP_SET_BIG_DATA 0xfa > +#define SSP_MSG2SSP_AP_START_BIG_DATA 0xfb > +#define SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX 0xfd > +#define SSP_MSG2SSP_AP_SENSOR_TILT 0xea > +#define SSP_MSG2SSP_AP_MCU_SET_TIME 0xfe > +#define SSP_MSG2SSP_AP_MCU_GET_TIME 0xff > + > +#define SSP_MSG2SSP_AP_FUSEROM 0x01 > + > +/* voice data */ > +#define SSP_TYPE_WAKE_UP_VOICE_SERVICE 0x01 > +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_AM 0x01 > +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_GRAMMER 0x02 > + > +/* Factory Test */ > +#define SSP_ACCELEROMETER_FACTORY 0x80 > +#define SSP_GYROSCOPE_FACTORY 0x81 > +#define SSP_GEOMAGNETIC_FACTORY 0x82 > +#define SSP_PRESSURE_FACTORY 0x85 > +#define SSP_GESTURE_FACTORY 0x86 > +#define SSP_TEMPHUMIDITY_CRC_FACTORY 0x88 > +#define SSP_GYROSCOPE_TEMP_FACTORY 0x8a > +#define SSP_GYROSCOPE_DPS_FACTORY 0x8b > +#define SSP_MCU_FACTORY 0x8c > +#define SSP_MCU_SLEEP_FACTORY 0x8d > + > +/* SSP -> AP ACK about write CMD */ > +#define SSP_MSG_ACK 0x80 /* ACK from SSP to AP */ > +#define SSP_MSG_NAK 0x70 /* NAK from SSP to AP */ > + > +struct ssp_sensorhub_info { > + char *fw_name; > + char *fw_crashed_name; > + unsigned int fw_rev; > + const u8 * const mag_table; > + const unsigned int mag_length; > +}; > + > +/* ssp_msg options bit */ > +#define SSP_RW 0 > +#define SSP_INDEX 3 > + > +#define SSP_AP2HUB_READ 0 > +#define SSP_AP2HUB_WRITE 1 > +#define SSP_HUB2AP_WRITE 2 > +#define SSP_AP2HUB_READY 3 > +#define SSP_AP2HUB_RETURN 4 > + > +/** > + * struct ssp_data - ssp platformdata structure > + * @spi: spi device > + * @sensorhub_info: info about sensorhub board specific features > + * @wdt_timer: watchdog timer > + * @work_wdt: watchdog work > + * @work_firmware: firmware upgrade work queue > + * @work_refresh: refresh work queue for reset request from MCU > + * @shut_down: shut down flag > + * @mcu_dump_mode: mcu dump mode for debug > + * @time_syncing: time syncing indication flag > + * @timestamp: previous time in ns calculated for time syncing > + * @check_status: status table for each sensor > + * @com_fail_cnt: communication fail count > + * @reset_cnt: reset count > + * @timeout_cnt: timeout count > + * @available_sensors: available sensors seen by sensorhub (bit array) > + * @cur_firm_rev: cached current firmware revision > + * @last_resume_state: last AP resume/suspend state used to handle the PM > + * state of ssp > + * @last_ap_state: (obsolete) sleep notification for MCU > + * @sensor_enable: sensor enable mask > + * @delay_buf: data acquisition intervals table > + * @batch_latency_buf: yet unknown but existing in communication protocol > + * @batch_opt_buf: yet unknown but existing in communication protocol > + * @accel_position: yet unknown but existing in communication protocol > + * @mag_position: yet unknown but existing in communication protocol > + * @fw_dl_state: firmware download state > + * @comm_lock: lock protecting the handshake > + * @pending_lock: lock protecting pending list and completion > + * @mcu_reset_gpio: mcu reset line > + * @ap_mcu_gpio: ap to mcu gpio line > + * @mcu_ap_gpio: mcu to ap gpio line > + * @pending_list: pending list for messages queued to be sent/read > + * @sensor_devs: registered IIO devices table > + * @enable_refcount: enable reference count for wdt (watchdog timer) > + * @header_buffer: cache aligned buffer for packet header > + */ > +struct ssp_data { > + struct spi_device *spi; > + struct ssp_sensorhub_info *sensorhub_info; > + struct timer_list wdt_timer; > + struct work_struct work_wdt; > + struct delayed_work work_refresh; > + > + bool shut_down; > + bool mcu_dump_mode; > + bool time_syncing; > + int64_t timestamp; > + > + int check_status[SSP_SENSOR_MAX]; > + > + unsigned int com_fail_cnt; > + unsigned int reset_cnt; > + unsigned int timeout_cnt; > + > + unsigned int available_sensors; > + unsigned int cur_firm_rev; > + > + char last_resume_state; > + char last_ap_state; > + > + unsigned int sensor_enable; > + u32 delay_buf[SSP_SENSOR_MAX]; > + s32 batch_latency_buf[SSP_SENSOR_MAX]; > + s8 batch_opt_buf[SSP_SENSOR_MAX]; > + > + int accel_position; > + int mag_position; > + int fw_dl_state; > + > + struct mutex comm_lock; > + struct mutex pending_lock; > + > + int mcu_reset_gpio; > + int ap_mcu_gpio; > + int mcu_ap_gpio; > + > + struct list_head pending_list; > + > + struct iio_dev *sensor_devs[SSP_SENSOR_MAX]; > + atomic_t enable_refcount; > + > + __le16 header_buffer[SSP_HEADER_BUFFER_SIZE / sizeof(__le16)] > + ____cacheline_aligned; > +}; > + > +void ssp_clean_pending_list(struct ssp_data *data); > + > +int ssp_command(struct ssp_data *data, char command, int arg); > + > +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, > + u8 *send_buf, u8 length); > + > +int ssp_irq_msg(struct ssp_data *data); > + > +int ssp_get_chipid(struct ssp_data *data); > + > +int ssp_set_magnetic_matrix(struct ssp_data *data); > + > +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data); > + > +unsigned int ssp_get_firmware_rev(struct ssp_data *data); > + > +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay); > + > +#endif /* __SSP_SENSORHUB_H__ */ > diff --git a/drivers/iio/common/ssp_sensors/ssp_dev.c b/drivers/iio/common/ssp_sensors/ssp_dev.c > new file mode 100644 > index 0000000..6b22115 > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_dev.c > @@ -0,0 +1,712 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/iio/iio.h> > +#include <linux/interrupt.h> > +#include <linux/io.h> > +#include <linux/mfd/core.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_gpio.h> > +#include <linux/of_platform.h> > +#include "ssp.h" > + > +#define SSP_WDT_TIME 10000 > +#define SSP_LIMIT_RESET_CNT 20 > +#define SSP_LIMIT_TIMEOUT_CNT 3 > + > +/* It is possible that it is max clk rate for version 1.0 of bootcode */ > +#define SSP_BOOT_SPI_HZ 400000 > + > +/* > + * These fields can look enigmatic but this structure is used mainly to flat > + * some values and depends on command type. > + */ > +struct ssp_instruction { > + __le32 a; > + __le32 b; > + u8 c; > +} __attribute__((__packed__)); > + > +static const u8 ssp_magnitude_table[] = {110, 85, 171, 71, 203, 195, 0, 67, > + 208, 56, 175, 244, 206, 213, 0, 92, 250, 0, 55, 48, 189, 252, 171, > + 243, 13, 45, 250}; > + > +static const struct ssp_sensorhub_info ssp_rinato_info = { > + .fw_name = "ssp_B2.fw", > + .fw_crashed_name = "ssp_crashed.fw", > + .fw_rev = 14052300, > + .mag_table = ssp_magnitude_table, > + .mag_length = ARRAY_SIZE(ssp_magnitude_table), > +}; > + > +static const struct ssp_sensorhub_info ssp_thermostat_info = { > + .fw_name = "thermostat_B2.fw", > + .fw_crashed_name = "ssp_crashed.fw", > + .fw_rev = 14080600, > + .mag_table = ssp_magnitude_table, > + .mag_length = ARRAY_SIZE(ssp_magnitude_table), > +}; > + > +static const struct mfd_cell sensorhub_sensor_devs[] = { > + { > + .name = "ssp-accelerometer", > + }, > + { > + .name = "ssp-gyroscope", > + }, > +}; > + > +static void ssp_toggle_mcu_reset_gpio(struct ssp_data *data) > +{ > + gpio_set_value(data->mcu_reset_gpio, 0); > + usleep_range(1000, 1200); > + gpio_set_value(data->mcu_reset_gpio, 1); > + msleep(50); > +} > + > +static void ssp_sync_available_sensors(struct ssp_data *data) > +{ > + int i, ret; > + > + for (i = 0; i < SSP_SENSOR_MAX; ++i) { > + if (data->available_sensors & BIT(i)) { > + ret = ssp_enable_sensor(data, i, data->delay_buf[i]); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "Sync sensor nr: %d fail\n", i); > + continue; > + } > + } > + } > + > + ret = ssp_command(data, SSP_MSG2SSP_AP_MCU_SET_DUMPMODE, > + data->mcu_dump_mode); > + if (ret < 0) > + dev_err(&data->spi->dev, > + "SSP_MSG2SSP_AP_MCU_SET_DUMPMODE failed\n"); > +} > + > +static void ssp_enable_mcu(struct ssp_data *data, bool enable) > +{ > + dev_info(&data->spi->dev, "current shutdown = %d, old = %d\n", enable, > + data->shut_down); > + > + if (enable && data->shut_down) { > + data->shut_down = false; > + enable_irq(data->spi->irq); > + enable_irq_wake(data->spi->irq); > + } else if (!enable && !data->shut_down) { > + data->shut_down = true; > + disable_irq(data->spi->irq); > + disable_irq_wake(data->spi->irq); > + } else { > + dev_warn(&data->spi->dev, "current shutdown = %d, old = %d\n", > + enable, data->shut_down); > + } > +} > + > +/* > + * This function is the first one which communicates with the mcu so it is > + * possible that the first attempt will fail > + */ > +static int ssp_check_fwbl(struct ssp_data *data) > +{ > + int retries = 0; > + > + while (retries++ < 5) { > + data->cur_firm_rev = ssp_get_firmware_rev(data); > + if (data->cur_firm_rev == SSP_INVALID_REVISION || > + data->cur_firm_rev == SSP_INVALID_REVISION2) { > + dev_warn(&data->spi->dev, > + "Invalid revision, trying %d time\n", retries); > + } else { > + break; > + } > + } > + > + if (data->cur_firm_rev == SSP_INVALID_REVISION || > + data->cur_firm_rev == SSP_INVALID_REVISION2) { > + dev_err(&data->spi->dev, "SSP_INVALID_REVISION\n"); > + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; > + } > + > + dev_info(&data->spi->dev, > + "MCU Firm Rev : Old = %8u, New = %8u\n", > + data->cur_firm_rev, > + data->sensorhub_info->fw_rev); > + > + if (data->cur_firm_rev != data->sensorhub_info->fw_rev) > + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; > + > + return SSP_FW_DL_STATE_NONE; > +} > + > +static void ssp_reset_mcu(struct ssp_data *data) > +{ > + ssp_enable_mcu(data, false); > + ssp_clean_pending_list(data); > + ssp_toggle_mcu_reset_gpio(data); > + ssp_enable_mcu(data, true); > +} > + > +static void ssp_wdt_work_func(struct work_struct *work) > +{ > + struct ssp_data *data = container_of(work, struct ssp_data, work_wdt); > + > + dev_err(&data->spi->dev, "%s - Sensor state: 0x%x, RC: %u, CC: %u\n", > + __func__, data->available_sensors, data->reset_cnt, > + data->com_fail_cnt); > + > + ssp_reset_mcu(data); > + data->com_fail_cnt = 0; > + data->timeout_cnt = 0; > +} > + > +static void ssp_wdt_timer_func(unsigned long ptr) > +{ > + struct ssp_data *data = (struct ssp_data *)ptr; > + > + switch (data->fw_dl_state) { > + case SSP_FW_DL_STATE_FAIL: > + case SSP_FW_DL_STATE_DOWNLOADING: > + case SSP_FW_DL_STATE_SYNC: > + goto _mod; > + } > + > + if (data->timeout_cnt > SSP_LIMIT_TIMEOUT_CNT || > + data->com_fail_cnt > SSP_LIMIT_RESET_CNT) > + queue_work(system_power_efficient_wq, &data->work_wdt); > +_mod: > + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); > +} > + > +static void ssp_enable_wdt_timer(struct ssp_data *data) > +{ > + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); > +} > + > +static void ssp_disable_wdt_timer(struct ssp_data *data) > +{ > + del_timer_sync(&data->wdt_timer); > + cancel_work_sync(&data->work_wdt); > +} > + > +/** > + * ssp_get_sensor_delay() - gets sensor data acquisition period > + * @data: sensorhub structure > + * @type: SSP sensor type > + * > + * Returns acquisition period in ms > + */ > +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type type) > +{ > + return data->delay_buf[type]; > +} > +EXPORT_SYMBOL(ssp_get_sensor_delay); > + > +/** > + * ssp_enable_sensor() - enables data acquisition for sensor > + * @data: sensorhub structure > + * @type: SSP sensor type > + * @delay: delay in ms > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay) > +{ > + int ret; > + struct ssp_instruction to_send; > + > + to_send.a = cpu_to_le32(delay); > + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); > + to_send.c = data->batch_opt_buf[type]; > + > + switch (data->check_status[type]) { > + case SSP_INITIALIZATION_STATE: > + /* do calibration step, now just enable */ > + case SSP_ADD_SENSOR_STATE: > + ret = ssp_send_instruction(data, > + SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD, > + type, > + (u8 *)&to_send, sizeof(to_send)); > + if (ret < 0) { > + dev_err(&data->spi->dev, "Enabling sensor failed\n"); > + data->check_status[type] = SSP_NO_SENSOR_STATE; > + goto derror; > + } > + > + data->sensor_enable |= BIT(type); > + data->check_status[type] = SSP_RUNNING_SENSOR_STATE; > + break; > + case SSP_RUNNING_SENSOR_STATE: > + ret = ssp_send_instruction(data, > + SSP_MSG2SSP_INST_CHANGE_DELAY, type, > + (u8 *)&to_send, sizeof(to_send)); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "Changing sensor delay failed\n"); > + goto derror; > + } > + break; > + default: > + data->check_status[type] = SSP_ADD_SENSOR_STATE; > + break; > + } > + > + data->delay_buf[type] = delay; > + > + if (atomic_inc_return(&data->enable_refcount) == 1) > + ssp_enable_wdt_timer(data); > + > + return 0; > + > +derror: > + return ret; > +} > +EXPORT_SYMBOL(ssp_enable_sensor); > + > +/** > + * ssp_change_delay() - changes data acquisition for sensor > + * @data: sensorhub structure > + * @type: SSP sensor type > + * @delay: delay in ms > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay) > +{ > + int ret; > + struct ssp_instruction to_send; > + > + to_send.a = cpu_to_le32(delay); > + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); > + to_send.c = data->batch_opt_buf[type]; > + > + ret = ssp_send_instruction(data, SSP_MSG2SSP_INST_CHANGE_DELAY, type, > + (u8 *)&to_send, sizeof(to_send)); > + if (ret < 0) { > + dev_err(&data->spi->dev, "Changing sensor delay failed\n"); > + return ret; > + } > + > + data->delay_buf[type] = delay; > + > + return 0; > +} > +EXPORT_SYMBOL(ssp_change_delay); > + > +/** > + * ssp_disable_sensor() - disables sensor > + * > + * @data: sensorhub structure > + * @type: SSP sensor type > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type) > +{ > + int ret; > + __le32 command; > + > + if (data->sensor_enable & BIT(type)) { > + command = cpu_to_le32(data->delay_buf[type]); > + > + ret = ssp_send_instruction(data, > + SSP_MSG2SSP_INST_BYPASS_SENSOR_RM, > + type, (u8 *)&command, > + sizeof(command)); > + if (ret < 0) { > + dev_err(&data->spi->dev, "Remove sensor fail\n"); > + return ret; > + } > + > + data->sensor_enable &= ~BIT(type); > + } > + > + data->check_status[type] = SSP_ADD_SENSOR_STATE; > + > + if (atomic_dec_and_test(&data->enable_refcount)) > + ssp_disable_wdt_timer(data); > + > + return 0; > +} > +EXPORT_SYMBOL(ssp_disable_sensor); > + > +static irqreturn_t ssp_irq_thread_fn(int irq, void *dev_id) > +{ > + struct ssp_data *data = dev_id; > + > + /* > + * This wrapper is done to preserve error path for ssp_irq_msg, also > + * it is defined in different file. > + */ > + ssp_irq_msg(data); > + > + return IRQ_HANDLED; > +} > + > +static int ssp_initialize_mcu(struct ssp_data *data) > +{ > + int ret; > + > + ssp_clean_pending_list(data); > + > + ret = ssp_get_chipid(data); > + if (ret != SSP_DEVICE_ID) { > + dev_err(&data->spi->dev, "%s - MCU %s ret = %d\n", __func__, > + ret < 0 ? "is not working" : "identification failed", > + ret); > + return ret < 0 ? ret : -ENODEV; > + } > + > + dev_info(&data->spi->dev, "MCU device ID = %d\n", ret); > + > + /* > + * needs clarification, for now do not want to export all transfer > + * methods to sensors' drivers > + */ > + ret = ssp_set_magnetic_matrix(data); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "%s - ssp_set_magnetic_matrix failed\n", __func__); > + return ret; > + } > + > + data->available_sensors = ssp_get_sensor_scanning_info(data); > + if (data->available_sensors == 0) { > + dev_err(&data->spi->dev, > + "%s - ssp_get_sensor_scanning_info failed\n", __func__); > + return -EIO; > + } > + > + data->cur_firm_rev = ssp_get_firmware_rev(data); > + dev_info(&data->spi->dev, "MCU Firm Rev : New = %8u\n", > + data->cur_firm_rev); > + > + return ssp_command(data, SSP_MSG2SSP_AP_MCU_DUMP_CHECK, 0); > +} > + > +/* > + * sensorhub can request its reinitialization as some brutal and rare error > + * handling. It can be requested from the MCU. > + */ > +static void ssp_refresh_task(struct work_struct *work) > +{ > + struct ssp_data *data = container_of((struct delayed_work *)work, > + struct ssp_data, work_refresh); > + > + dev_info(&data->spi->dev, "refreshing\n"); > + > + data->reset_cnt++; > + > + if (ssp_initialize_mcu(data) >= 0) { > + ssp_sync_available_sensors(data); > + if (data->last_ap_state != 0) > + ssp_command(data, data->last_ap_state, 0); > + > + if (data->last_resume_state != 0) > + ssp_command(data, data->last_resume_state, 0); > + > + data->timeout_cnt = 0; > + data->com_fail_cnt = 0; > + } > +} > + > +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay) > +{ > + cancel_delayed_work_sync(&data->work_refresh); > + > + return queue_delayed_work(system_power_efficient_wq, > + &data->work_refresh, > + msecs_to_jiffies(delay)); > +} > + > +#ifdef CONFIG_OF > +static struct of_device_id ssp_of_match[] = { > + { > + .compatible = "samsung,sensorhub-rinato", > + .data = &ssp_rinato_info, > + }, { > + .compatible = "samsung,sensorhub-thermostat", > + .data = &ssp_thermostat_info, > + }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, ssp_of_match); > + > +static struct ssp_data *ssp_parse_dt(struct device *dev) > +{ > + int ret; > + struct ssp_data *data; > + struct device_node *node = dev->of_node; > + const struct of_device_id *match; > + > + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); > + if (!data) > + return NULL; > + > + data->mcu_ap_gpio = of_get_named_gpio(node, "mcu-ap-gpios", 0); > + if (data->mcu_ap_gpio < 0) > + goto err_free_pd; > + > + data->ap_mcu_gpio = of_get_named_gpio(node, "ap-mcu-gpios", 0); > + if (data->ap_mcu_gpio < 0) > + goto err_free_pd; > + > + data->mcu_reset_gpio = of_get_named_gpio(node, "mcu-reset-gpios", 0); > + if (data->mcu_reset_gpio < 0) > + goto err_free_pd; > + > + ret = devm_gpio_request_one(dev, data->ap_mcu_gpio, GPIOF_OUT_INIT_HIGH, > + "ap-mcu-gpios"); > + if (ret) > + goto err_free_pd; > + > + ret = devm_gpio_request_one(dev, data->mcu_reset_gpio, > + GPIOF_OUT_INIT_HIGH, "mcu-reset-gpios"); > + if (ret) > + goto err_ap_mcu; > + > + match = of_match_node(ssp_of_match, node); > + if (!match) > + goto err_mcu_reset_gpio; > + > + data->sensorhub_info = (struct ssp_sensorhub_info *)match->data; > + > + dev_set_drvdata(dev, data); > + > + return data; > + > +err_mcu_reset_gpio: > + devm_gpio_free(dev, data->mcu_reset_gpio); > +err_ap_mcu: > + devm_gpio_free(dev, data->ap_mcu_gpio); > +err_free_pd: > + devm_kfree(dev, data); > + return NULL; > +} > +#else > +static struct ssp_data *ssp_parse_dt(struct platform_device *pdev) > +{ This has incorrect arguements.. So causes a build error. > + return NULL; > +} > +#endif > + > +/** > + * ssp_register_consumer() - registers iio consumer in ssp framework > + * > + * @indio_dev: consumer iio device > + * @type: ssp sensor type > + */ > +void ssp_register_consumer(struct iio_dev *indio_dev, enum ssp_sensor_type type) > +{ > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + data->sensor_devs[type] = indio_dev; > +} > +EXPORT_SYMBOL(ssp_register_consumer); > + > +static int ssp_probe(struct spi_device *spi) > +{ > + int ret, i; > + struct ssp_data *data; > + > + data = ssp_parse_dt(&spi->dev); > + if (!data) { > + dev_err(&spi->dev, "Failed to find platform data\n"); > + return -ENODEV; > + } > + > + ret = mfd_add_devices(&spi->dev, -1, sensorhub_sensor_devs, > + ARRAY_SIZE(sensorhub_sensor_devs), NULL, 0, NULL); > + if (ret < 0) { > + dev_err(&spi->dev, "mfd add devices fail\n"); > + return ret; > + } > + > + spi->mode = SPI_MODE_1; > + ret = spi_setup(spi); > + if (ret < 0) { > + dev_err(&spi->dev, "Failed to setup spi\n"); > + return ret; > + } > + > + data->fw_dl_state = SSP_FW_DL_STATE_NONE; > + data->spi = spi; > + spi_set_drvdata(spi, data); > + > + mutex_init(&data->comm_lock); > + > + for (i = 0; i < SSP_SENSOR_MAX; ++i) { > + data->delay_buf[i] = SSP_DEFAULT_POLLING_DELAY; > + data->batch_latency_buf[i] = 0; > + data->batch_opt_buf[i] = 0; > + data->check_status[i] = SSP_INITIALIZATION_STATE; > + } > + > + data->delay_buf[SSP_BIO_HRM_LIB] = 100; > + > + data->time_syncing = true; > + > + mutex_init(&data->pending_lock); > + INIT_LIST_HEAD(&data->pending_list); > + > + atomic_set(&data->enable_refcount, 0); > + > + INIT_WORK(&data->work_wdt, ssp_wdt_work_func); > + INIT_DELAYED_WORK(&data->work_refresh, ssp_refresh_task); > + > + setup_timer(&data->wdt_timer, ssp_wdt_timer_func, (unsigned long)data); > + > + ret = request_threaded_irq(data->spi->irq, NULL, > + ssp_irq_thread_fn, > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + "SSP_Int", data); > + if (ret < 0) { > + dev_err(&spi->dev, "Irq request fail\n"); > + goto err_setup_irq; > + } > + > + /* Let's start with enabled one so irq balance could be ok */ > + data->shut_down = false; > + > + /* just to avoid unbalanced irq set wake up */ > + enable_irq_wake(data->spi->irq); > + > + data->fw_dl_state = ssp_check_fwbl(data); > + if (data->fw_dl_state == SSP_FW_DL_STATE_NONE) { > + ret = ssp_initialize_mcu(data); > + if (ret < 0) { > + dev_err(&spi->dev, "Initialize_mcu failed\n"); > + goto err_read_reg; > + } > + } else { > + dev_err(&spi->dev, "Firmware version not supported\n"); > + ret = -EPERM; > + goto err_read_reg; > + } > + > + return 0; > + > +err_read_reg: > + free_irq(data->spi->irq, data); > +err_setup_irq: > + mutex_destroy(&data->pending_lock); > + mutex_destroy(&data->comm_lock); > + > + dev_err(&spi->dev, "Probe failed!\n"); > + > + return ret; > +} > + > +static int ssp_remove(struct spi_device *spi) > +{ > + struct ssp_data *data = spi_get_drvdata(spi); > + > + if (ssp_command(data, SSP_MSG2SSP_AP_STATUS_SHUTDOWN, 0) < 0) > + dev_err(&data->spi->dev, > + "SSP_MSG2SSP_AP_STATUS_SHUTDOWN failed\n"); > + > + ssp_enable_mcu(data, false); > + ssp_disable_wdt_timer(data); > + > + ssp_clean_pending_list(data); > + > + free_irq(data->spi->irq, data); > + > + del_timer_sync(&data->wdt_timer); > + cancel_work_sync(&data->work_wdt); > + > + mutex_destroy(&data->comm_lock); > + mutex_destroy(&data->pending_lock); > + > + mfd_remove_devices(&spi->dev); > + > + return 0; > +} > + > +static int ssp_suspend(struct device *dev) > +{ > + int ret; > + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); > + > + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_SUSPEND; > + > + if (atomic_read(&data->enable_refcount) > 0) > + ssp_disable_wdt_timer(data); > + > + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_SUSPEND, 0); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "%s SSP_MSG2SSP_AP_STATUS_SUSPEND failed\n", __func__); > + > + ssp_enable_wdt_timer(data); > + return ret; > + } > + > + data->time_syncing = false; > + disable_irq(data->spi->irq); > + > + return 0; > +} > + > +static int ssp_resume(struct device *dev) > +{ > + int ret; > + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); > + > + enable_irq(data->spi->irq); > + > + if (atomic_read(&data->enable_refcount) > 0) > + ssp_enable_wdt_timer(data); > + > + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_RESUME, 0); > + if (ret < 0) { > + dev_err(&data->spi->dev, > + "%s SSP_MSG2SSP_AP_STATUS_RESUME failed\n", __func__); > + ssp_disable_wdt_timer(data); > + return ret; > + } > + > + /* timesyncing is set by MCU */ > + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_RESUME; > + > + return 0; > +} > + > +static const struct dev_pm_ops ssp_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(ssp_suspend, ssp_resume) > +}; > + > +static struct spi_driver ssp_driver = { > + .probe = ssp_probe, > + .remove = ssp_remove, > + .driver = { > + .pm = &ssp_pm_ops, > + .bus = &spi_bus_type, > + .owner = THIS_MODULE, > + .of_match_table = of_match_ptr(ssp_of_match), > + .name = "sensorhub" > + }, > +}; > + > +module_spi_driver(ssp_driver); > + > +MODULE_DESCRIPTION("ssp sensorhub driver"); > +MODULE_AUTHOR("Samsung Electronics"); > +MODULE_LICENSE("GPL"); > diff --git a/drivers/iio/common/ssp_sensors/ssp_spi.c b/drivers/iio/common/ssp_sensors/ssp_spi.c > new file mode 100644 > index 0000000..704284a > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_spi.c > @@ -0,0 +1,608 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include "ssp.h" > + > +#define SSP_DEV (&data->spi->dev) > +#define SSP_GET_MESSAGE_TYPE(data) (data & (3 << SSP_RW)) > + > +/* > + * SSP -> AP Instruction > + * They tell what packet type can be expected. In the future there will > + * be less of them. BYPASS means common sensor packets with accel, gyro, > + * hrm etc. data. LIBRARY and META are mock-up's for now. > + */ > +#define SSP_MSG2AP_INST_BYPASS_DATA 0x37 > +#define SSP_MSG2AP_INST_LIBRARY_DATA 0x01 > +#define SSP_MSG2AP_INST_DEBUG_DATA 0x03 > +#define SSP_MSG2AP_INST_BIG_DATA 0x04 > +#define SSP_MSG2AP_INST_META_DATA 0x05 > +#define SSP_MSG2AP_INST_TIME_SYNC 0x06 > +#define SSP_MSG2AP_INST_RESET 0x07 > + > +#define SSP_UNIMPLEMENTED -1 > + > +struct ssp_msg_header { > + u8 cmd; > + __le16 length; > + __le16 options; > + __le32 data; > +} __attribute__((__packed__)); > + > +struct ssp_msg { > + u16 length; > + u16 options; > + struct list_head list; > + struct completion *done; > + struct ssp_msg_header *h; > + char *buffer; > +}; > + > +static const int ssp_offset_map[SSP_SENSOR_MAX] = { > + [SSP_ACCELEROMETER_SENSOR] = SSP_ACCELEROMETER_SIZE + > + SSP_TIME_SIZE, > + [SSP_GYROSCOPE_SENSOR] = SSP_GYROSCOPE_SIZE + > + SSP_TIME_SIZE, > + [SSP_GEOMAGNETIC_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GEOMAGNETIC_RAW] = SSP_UNIMPLEMENTED, > + [SSP_GEOMAGNETIC_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_PRESSURE_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GESTURE_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_PROXIMITY_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_TEMPERATURE_HUMIDITY_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_LIGHT_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_PROXIMITY_RAW] = SSP_UNIMPLEMENTED, > + [SSP_ORIENTATION_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_STEP_DETECTOR] = SSP_UNIMPLEMENTED, > + [SSP_SIG_MOTION_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GYRO_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, > + [SSP_GAME_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, > + [SSP_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, > + [SSP_STEP_COUNTER] = SSP_UNIMPLEMENTED, > + [SSP_BIO_HRM_RAW] = SSP_BIO_HRM_RAW_SIZE + > + SSP_TIME_SIZE, > + [SSP_BIO_HRM_RAW_FAC] = SSP_BIO_HRM_RAW_FAC_SIZE + > + SSP_TIME_SIZE, > + [SSP_BIO_HRM_LIB] = SSP_BIO_HRM_LIB_SIZE + > + SSP_TIME_SIZE, > +}; > + > +#define SSP_HEADER_SIZE (sizeof(struct ssp_msg_header)) > +#define SSP_HEADER_SIZE_ALIGNED (ALIGN(SSP_HEADER_SIZE, 4)) > + > +static struct ssp_msg *ssp_create_msg(u8 cmd, u16 len, u16 opt, u32 data) > +{ > + struct ssp_msg_header h; > + struct ssp_msg *msg; > + > + msg = kzalloc(sizeof(*msg), GFP_KERNEL); > + if (!msg) > + return NULL; > + > + h.cmd = cmd; > + h.length = cpu_to_le16(len); > + h.options = cpu_to_le16(opt); > + h.data = cpu_to_le32(data); > + > + msg->buffer = kzalloc(SSP_HEADER_SIZE_ALIGNED + len, > + GFP_KERNEL | GFP_DMA); > + if (!msg->buffer) { > + kfree(msg); > + return NULL; > + } > + > + msg->length = len; > + msg->options = opt; > + > + memcpy(msg->buffer, &h, SSP_HEADER_SIZE); > + > + return msg; > +} > + > +/* > + * It is a bit heavy to do it this way but often the function is used to compose > + * the message from smaller chunks which are placed on the stack. Often the > + * chunks are small so memcpy should be optimalized. > + */ > +static inline void ssp_fill_buffer(struct ssp_msg *m, unsigned int offset, > + const void *src, unsigned int len) > +{ > + memcpy(&m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], src, len); > +} > + > +static inline void ssp_get_buffer(struct ssp_msg *m, unsigned int offset, > + void *dest, unsigned int len) > +{ > + memcpy(dest, &m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], len); > +} > + > +#define SSP_GET_BUFFER_AT_INDEX(m, index) \ > + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index]) > +#define SSP_SET_BUFFER_AT_INDEX(m, index, val) \ > + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index] = val) > + > +static void ssp_clean_msg(struct ssp_msg *m) > +{ > + kfree(m->buffer); > + kfree(m); > +} > + > +static int ssp_print_mcu_debug(char *data_frame, int *data_index, > + int received_len) > +{ > + int length = data_frame[(*data_index)++]; > + > + if (length > received_len - *data_index || length <= 0) { > + ssp_dbg("[SSP]: MSG From MCU-invalid debug length(%d/%d)\n", > + length, received_len); > + return length ? length : -EPROTO; > + } > + > + ssp_dbg("[SSP]: MSG From MCU - %s\n", &data_frame[*data_index]); > + > + *data_index += length; > + > + return 0; > +} > + > +/* > + * It was designed that way - additional lines to some kind of handshake, > + * please do not ask why - only the firmware guy can know it. > + */ > +static int ssp_check_lines(struct ssp_data *data, bool state) > +{ > + int delay_cnt = 0; > + > + gpio_set_value_cansleep(data->ap_mcu_gpio, state); > + > + while (gpio_get_value_cansleep(data->mcu_ap_gpio) != state) { > + usleep_range(3000, 3500); > + > + if (data->shut_down || delay_cnt++ > 500) { > + dev_err(SSP_DEV, "%s:timeout, hw ack wait fail %d\n", > + __func__, state); > + > + if (!state) > + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); > + > + return -ETIMEDOUT; > + } > + } > + > + return 0; > +} > + > +static int ssp_do_transfer(struct ssp_data *data, struct ssp_msg *msg, > + struct completion *done, int timeout) > +{ > + int status; > + /* > + * check if this is a short one way message or the whole transfer has > + * second part after an interrupt > + */ > + const bool use_no_irq = msg->length == 0; > + > + if (data->shut_down) > + return -EPERM; > + > + msg->done = done; > + > + mutex_lock(&data->comm_lock); > + > + status = ssp_check_lines(data, false); > + if (status < 0) > + goto _error_locked; > + > + status = spi_write(data->spi, msg->buffer, SSP_HEADER_SIZE); > + if (status < 0) { > + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); > + dev_err(SSP_DEV, "%s spi_write fail\n", __func__); > + goto _error_locked; > + } > + > + if (!use_no_irq) { > + mutex_lock(&data->pending_lock); > + list_add_tail(&msg->list, &data->pending_list); > + mutex_unlock(&data->pending_lock); > + } > + > + status = ssp_check_lines(data, true); > + if (status < 0) { > + if (!use_no_irq) { > + mutex_lock(&data->pending_lock); > + list_del(&msg->list); > + mutex_unlock(&data->pending_lock); > + } > + goto _error_locked; > + } > + > + mutex_unlock(&data->comm_lock); > + > + if (!use_no_irq && done) > + if (wait_for_completion_timeout(done, > + msecs_to_jiffies(timeout)) == > + 0) { > + mutex_lock(&data->pending_lock); > + list_del(&msg->list); > + mutex_unlock(&data->pending_lock); > + > + data->timeout_cnt++; > + return -ETIMEDOUT; > + } > + > + return 0; > + > +_error_locked: > + mutex_unlock(&data->comm_lock); > + data->timeout_cnt++; > + return status; > +} > + > +static inline int ssp_spi_sync_command(struct ssp_data *data, > + struct ssp_msg *msg) > +{ > + return ssp_do_transfer(data, msg, NULL, 0); > +} > + > +static int ssp_spi_sync(struct ssp_data *data, struct ssp_msg *msg, > + int timeout) > +{ > + DECLARE_COMPLETION_ONSTACK(done); > + > + if (WARN_ON(!msg->length)) > + return -EPERM; > + > + return ssp_do_transfer(data, msg, &done, timeout); > +} > + > +static int ssp_handle_big_data(struct ssp_data *data, char *dataframe, int *idx) > +{ > + /* mock-up, it will be changed with adding another sensor types */ > + *idx += 8; > + return 0; > +} > + > +static int ssp_parse_dataframe(struct ssp_data *data, char *dataframe, int len) > +{ > + int idx, sd; > + struct timespec ts; > + struct ssp_sensor_data *spd; > + struct iio_dev **indio_devs = data->sensor_devs; > + > + getnstimeofday(&ts); > + > + for (idx = 0; idx < len;) { > + switch (dataframe[idx++]) { > + case SSP_MSG2AP_INST_BYPASS_DATA: > + sd = dataframe[idx++]; > + if (sd < 0 || sd >= SSP_SENSOR_MAX) { > + dev_err(SSP_DEV, > + "Mcu data frame1 error %d\n", sd); > + return -EPROTO; > + } > + > + if (indio_devs[sd]) { > + spd = iio_priv(indio_devs[sd]); > + if (spd->process_data) > + spd->process_data(indio_devs[sd], > + &dataframe[idx], > + data->timestamp); > + } else { > + dev_err(SSP_DEV, "no client for frame\n"); > + } > + > + idx += ssp_offset_map[sd]; > + break; > + case SSP_MSG2AP_INST_DEBUG_DATA: > + sd = ssp_print_mcu_debug(dataframe, &idx, len); > + if (sd) { > + dev_err(SSP_DEV, > + "Mcu data frame3 error %d\n", sd); > + return sd; > + } > + break; > + case SSP_MSG2AP_INST_LIBRARY_DATA: > + idx += len; > + break; > + case SSP_MSG2AP_INST_BIG_DATA: > + ssp_handle_big_data(data, dataframe, &idx); > + break; > + case SSP_MSG2AP_INST_TIME_SYNC: > + data->time_syncing = true; > + break; > + case SSP_MSG2AP_INST_RESET: > + ssp_queue_ssp_refresh_task(data, 0); > + break; > + } > + } > + > + if (data->time_syncing) > + data->timestamp = ts.tv_sec * 1000000000ULL + ts.tv_nsec; > + > + return 0; > +} > + > +/* threaded irq */ > +int ssp_irq_msg(struct ssp_data *data) > +{ > + bool found = false; > + char *buffer; > + u8 msg_type; > + int ret; > + u16 length, msg_options; > + struct ssp_msg *msg, *n; > + > + ret = spi_read(data->spi, data->header_buffer, SSP_HEADER_BUFFER_SIZE); > + if (ret < 0) { > + dev_err(SSP_DEV, "header read fail\n"); > + return ret; > + } > + > + length = le16_to_cpu(data->header_buffer[1]); > + msg_options = le16_to_cpu(data->header_buffer[0]); > + > + if (length == 0) { > + dev_err(SSP_DEV, "length received from mcu is 0\n"); > + return -EINVAL; > + } > + > + msg_type = SSP_GET_MESSAGE_TYPE(msg_options); > + > + switch (msg_type) { > + case SSP_AP2HUB_READ: > + case SSP_AP2HUB_WRITE: > + /* > + * this is a small list, a few elements - the packets can be > + * received with no order > + */ > + mutex_lock(&data->pending_lock); > + list_for_each_entry_safe(msg, n, &data->pending_list, list) { > + if (msg->options == msg_options) { > + list_del(&msg->list); > + found = true; > + break; > + } > + } > + > + if (!found) { > + /* > + * here can be implemented dead messages handling > + * but the slave should not send such ones - it is to > + * check but let's handle this > + */ > + buffer = kmalloc(length, GFP_KERNEL | GFP_DMA); > + if (!buffer) { > + ret = -ENOMEM; > + goto _unlock; > + } > + > + /* got dead packet so it is always an error */ > + ret = spi_read(data->spi, buffer, length); > + if (ret >= 0) > + ret = -EPROTO; > + > + kfree(buffer); > + > + dev_err(SSP_DEV, "No match error %x\n", > + msg_options); > + > + goto _unlock; > + } > + > + if (msg_type == SSP_AP2HUB_READ) > + ret = spi_read(data->spi, > + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], > + msg->length); > + > + if (msg_type == SSP_AP2HUB_WRITE) { > + ret = spi_write(data->spi, > + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], > + msg->length); > + if (msg_options & SSP_AP2HUB_RETURN) { > + msg->options = > + SSP_AP2HUB_READ | SSP_AP2HUB_RETURN; > + msg->length = 1; > + > + list_add_tail(&msg->list, &data->pending_list); > + goto _unlock; > + } > + } > + > + if (msg->done) > + if (!completion_done(msg->done)) > + complete(msg->done); > +_unlock: > + mutex_unlock(&data->pending_lock); > + break; > + case SSP_HUB2AP_WRITE: > + buffer = kzalloc(length, GFP_KERNEL | GFP_DMA); > + if (!buffer) > + return -ENOMEM; > + > + ret = spi_read(data->spi, buffer, length); > + if (ret < 0) { > + dev_err(SSP_DEV, "spi read fail\n"); > + kfree(buffer); > + break; > + } > + > + ret = ssp_parse_dataframe(data, buffer, length); > + > + kfree(buffer); > + break; > + > + default: > + dev_err(SSP_DEV, "unknown msg type\n"); > + return -EPROTO; > + } > + > + return ret; > +} > + > +void ssp_clean_pending_list(struct ssp_data *data) > +{ > + struct ssp_msg *msg, *n; > + > + mutex_lock(&data->pending_lock); > + list_for_each_entry_safe(msg, n, &data->pending_list, list) { > + list_del(&msg->list); > + > + if (msg->done) > + if (!completion_done(msg->done)) > + complete(msg->done); > + } > + mutex_unlock(&data->pending_lock); > +} > + > +int ssp_command(struct ssp_data *data, char command, int arg) > +{ > + int ret; > + struct ssp_msg *msg; > + > + msg = ssp_create_msg(command, 0, SSP_AP2HUB_WRITE, arg); > + if (!msg) > + return -ENOMEM; > + > + ssp_dbg("%s - command 0x%x %d\n", __func__, command, arg); > + > + ret = ssp_spi_sync_command(data, msg); > + ssp_clean_msg(msg); > + > + return ret; > +} > + > +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, > + u8 *send_buf, u8 length) > +{ > + int ret; > + struct ssp_msg *msg; > + > + if (data->fw_dl_state == SSP_FW_DL_STATE_DOWNLOADING) { > + dev_err(SSP_DEV, "%s - Skip Inst! DL state = %d\n", > + __func__, data->fw_dl_state); > + return -EBUSY; > + } else if (!(data->available_sensors & BIT(sensor_type)) && > + (inst <= SSP_MSG2SSP_INST_CHANGE_DELAY)) { > + dev_err(SSP_DEV, "%s - Bypass Inst Skip! - %u\n", > + __func__, sensor_type); > + return -EIO; /* just fail */ > + } > + > + msg = ssp_create_msg(inst, length + 2, SSP_AP2HUB_WRITE, 0); > + if (!msg) > + return -ENOMEM; > + > + ssp_fill_buffer(msg, 0, &sensor_type, 1); > + ssp_fill_buffer(msg, 1, send_buf, length); > + > + ssp_dbg("%s - Inst = 0x%x, Sensor Type = 0x%x, data = %u\n", > + __func__, inst, sensor_type, send_buf[1]); > + > + ret = ssp_spi_sync(data, msg, 1000); > + ssp_clean_msg(msg); > + > + return ret; > +} > + > +int ssp_get_chipid(struct ssp_data *data) > +{ > + int ret; > + char buffer; > + struct ssp_msg *msg; > + > + msg = ssp_create_msg(SSP_MSG2SSP_AP_WHOAMI, 1, SSP_AP2HUB_READ, 0); > + if (!msg) > + return -ENOMEM; > + > + ret = ssp_spi_sync(data, msg, 1000); > + > + buffer = SSP_GET_BUFFER_AT_INDEX(msg, 0); > + > + ssp_clean_msg(msg); > + > + return ret < 0 ? ret : buffer; > +} > + > +int ssp_set_magnetic_matrix(struct ssp_data *data) > +{ > + int ret; > + struct ssp_msg *msg; > + > + msg = ssp_create_msg(SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX, > + data->sensorhub_info->mag_length, SSP_AP2HUB_WRITE, > + 0); > + if (!msg) > + return -ENOMEM; > + > + ssp_fill_buffer(msg, 0, data->sensorhub_info->mag_table, > + data->sensorhub_info->mag_length); > + > + ret = ssp_spi_sync(data, msg, 1000); > + ssp_clean_msg(msg); > + > + return ret; > +} > + > +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data) > +{ > + int ret; > + __le32 result; > + u32 cpu_result = 0; > + > + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_SENSOR_SCANNING, 4, > + SSP_AP2HUB_READ, 0); > + if (!msg) > + return 0; > + > + ret = ssp_spi_sync(data, msg, 1000); > + if (ret < 0) { > + dev_err(SSP_DEV, "%s - spi read fail %d\n", __func__, ret); > + goto _exit; > + } > + > + ssp_get_buffer(msg, 0, &result, 4); > + cpu_result = le32_to_cpu(result); > + > + dev_info(SSP_DEV, "%s state: 0x%08x\n", __func__, cpu_result); > + > +_exit: > + ssp_clean_msg(msg); > + return cpu_result; > +} > + > +unsigned int ssp_get_firmware_rev(struct ssp_data *data) > +{ > + int ret; > + __le32 result; > + > + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_FIRMWARE_REV, 4, > + SSP_AP2HUB_READ, 0); > + if (!msg) > + return SSP_INVALID_REVISION; > + > + ret = ssp_spi_sync(data, msg, 1000); > + if (ret < 0) { > + dev_err(SSP_DEV, "%s - transfer fail %d\n", __func__, ret); > + ret = SSP_INVALID_REVISION; > + goto _exit; > + } > + > + ssp_get_buffer(msg, 0, &result, 4); > + ret = le32_to_cpu(result); > + > +_exit: > + ssp_clean_msg(msg); > + return ret; > +} > diff --git a/include/linux/iio/common/ssp_sensors.h b/include/linux/iio/common/ssp_sensors.h > new file mode 100644 > index 0000000..f4d1b0e > --- /dev/null > +++ b/include/linux/iio/common/ssp_sensors.h > @@ -0,0 +1,82 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > +#ifndef _SSP_SENSORS_H_ > +#define _SSP_SENSORS_H_ > + > +#include <linux/iio/iio.h> > + > +#define SSP_TIME_SIZE 4 > +#define SSP_ACCELEROMETER_SIZE 6 > +#define SSP_GYROSCOPE_SIZE 6 > +#define SSP_BIO_HRM_RAW_SIZE 8 > +#define SSP_BIO_HRM_RAW_FAC_SIZE 36 > +#define SSP_BIO_HRM_LIB_SIZE 8 > + > +/** > + * enum ssp_sensor_type - SSP sensor type > + */ > +enum ssp_sensor_type { > + SSP_ACCELEROMETER_SENSOR = 0, > + SSP_GYROSCOPE_SENSOR, > + SSP_GEOMAGNETIC_UNCALIB_SENSOR, > + SSP_GEOMAGNETIC_RAW, > + SSP_GEOMAGNETIC_SENSOR, > + SSP_PRESSURE_SENSOR, > + SSP_GESTURE_SENSOR, > + SSP_PROXIMITY_SENSOR, > + SSP_TEMPERATURE_HUMIDITY_SENSOR, > + SSP_LIGHT_SENSOR, > + SSP_PROXIMITY_RAW, > + SSP_ORIENTATION_SENSOR, > + SSP_STEP_DETECTOR, > + SSP_SIG_MOTION_SENSOR, > + SSP_GYRO_UNCALIB_SENSOR, > + SSP_GAME_ROTATION_VECTOR, > + SSP_ROTATION_VECTOR, > + SSP_STEP_COUNTER, > + SSP_BIO_HRM_RAW, > + SSP_BIO_HRM_RAW_FAC, > + SSP_BIO_HRM_LIB, > + SSP_SENSOR_MAX, > +}; > + > +struct ssp_data; > + > +/** > + * struct ssp_sensor_data - Sensor object > + * @process_data: Callback to feed sensor data. > + * @type: Used sensor type. > + * @buffer: Received data buffer. > + */ > +struct ssp_sensor_data { > + int (*process_data)(struct iio_dev *indio_dev, void *buf, > + int64_t timestamp); > + enum ssp_sensor_type type; > + u8 *buffer; > +}; > + > +void ssp_register_consumer(struct iio_dev *indio_dev, > + enum ssp_sensor_type type); > + > +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay); > + > +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type); > + > +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type); > + > +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, > + u32 delay); > +#endif /* _SSP_SENSORS_H_ */ > ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v5 1/5] iio: common: ssp_sensors: Add sensorhub driver 2015-01-29 18:35 ` Jonathan Cameron (?) @ 2015-01-29 18:46 ` Karol Wrona 2015-01-29 18:53 ` Jonathan Cameron -1 siblings, 1 reply; 19+ messages in thread From: Karol Wrona @ 2015-01-29 18:46 UTC (permalink / raw) To: Jonathan Cameron, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 01/29/2015 07:35 PM, Jonathan Cameron wrote: > On 28/01/15 14:05, Karol Wrona wrote: >> Sensorhub is MCU dedicated to collect data and manage several sensors. >> Sensorhub is a spi device which provides a layer for IIO devices. It provides >> some data parsing and common mechanism for sensorhub sensors. >> >> Adds common sensorhub library for sensorhub driver and iio drivers >> which uses sensorhub MCU to communicate with sensors. >> >> Signed-off-by: Karol Wrona <k.wrona@samsung.com> >> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> > A couple of build errors from this one... > > I've fixed them up and applied to the togreg branch of iio.git. > Pushed out as testing. If you get a chance to check I didn't > mess anything up that would be great. >> --- >> drivers/iio/common/Kconfig | 1 + >> drivers/iio/common/Makefile | 1 + >> drivers/iio/common/ssp_sensors/Kconfig | 26 ++ >> drivers/iio/common/ssp_sensors/Makefile | 8 + >> drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++++++ >> drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++++++++++++ >> drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++++++++++ >> include/linux/iio/common/ssp_sensors.h | 82 ++++ >> 8 files changed, 1695 insertions(+) >> create mode 100644 drivers/iio/common/ssp_sensors/Kconfig >> create mode 100644 drivers/iio/common/ssp_sensors/Makefile >> create mode 100644 drivers/iio/common/ssp_sensors/ssp.h >> create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c >> create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c >> create mode 100644 include/linux/iio/common/ssp_sensors.h >> >> diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig >> index 0b6e97d..790f106 100644 >> --- a/drivers/iio/common/Kconfig >> +++ b/drivers/iio/common/Kconfig >> @@ -3,4 +3,5 @@ >> # >> >> source "drivers/iio/common/hid-sensors/Kconfig" >> +source "drivers/iio/common/ssp_sensors/Kconfig" >> source "drivers/iio/common/st_sensors/Kconfig" >> diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile >> index 3112df0..b1e4d9c 100644 >> --- a/drivers/iio/common/Makefile >> +++ b/drivers/iio/common/Makefile >> @@ -8,4 +8,5 @@ >> >> # When adding new entries keep the list in alphabetical order >> obj-y += hid-sensors/ >> +obj-y += ssp_sensors/ >> obj-y += st_sensors/ >> diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig >> new file mode 100644 >> index 0000000..0ea4faf >> --- /dev/null >> +++ b/drivers/iio/common/ssp_sensors/Kconfig >> @@ -0,0 +1,26 @@ >> +# >> +# SSP sensor drivers and commons configuration >> +# >> +menu "SSP Sensor Common" >> + >> +config IIO_SSP_SENSORS_COMMONS >> + tristate "Commons for all SSP Sensor IIO drivers" >> + depends on IIO_SSP_SENSORHUB >> + select IIO_BUFFER >> + select IIO_KFIFO_BUF >> + help >> + Say yes here to build commons for SSP sensors. >> + To compile this as a module, choose M here: the module >> + will be called ssp_iio. >> + >> +config IIO_SSP_SENSORHUB >> + tristate "Samsung Sensorhub driver" >> + depends on SPI >> + select MFD_CORE >> + help >> + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. >> + To compile this driver as a module, choose M here: the >> + module will be called sensorhub. >> + >> +endmenu >> diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile >> new file mode 100644 >> index 0000000..1e0389e >> --- /dev/null >> +++ b/drivers/iio/common/ssp_sensors/Makefile >> @@ -0,0 +1,8 @@ >> +# >> +# Makefile for SSP sensor drivers and commons. >> +# >> + >> +sensorhub-objs := ssp_dev.o ssp_spi.o >> +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o >> + >> +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_iio.o > This file isn't in this patch. Thanks for doing that. I had to mess sth up during rebase. [...] ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v5 1/5] iio: common: ssp_sensors: Add sensorhub driver @ 2015-01-29 18:53 ` Jonathan Cameron 0 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:53 UTC (permalink / raw) To: Karol Wrona, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 29/01/15 18:46, Karol Wrona wrote: > On 01/29/2015 07:35 PM, Jonathan Cameron wrote: >> On 28/01/15 14:05, Karol Wrona wrote: >>> Sensorhub is MCU dedicated to collect data and manage several sensors. >>> Sensorhub is a spi device which provides a layer for IIO devices. It provides >>> some data parsing and common mechanism for sensorhub sensors. >>> >>> Adds common sensorhub library for sensorhub driver and iio drivers >>> which uses sensorhub MCU to communicate with sensors. >>> >>> Signed-off-by: Karol Wrona <k.wrona@samsung.com> >>> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> >> A couple of build errors from this one... >> >> I've fixed them up and applied to the togreg branch of iio.git. >> Pushed out as testing. If you get a chance to check I didn't >> mess anything up that would be great. >>> --- >>> drivers/iio/common/Kconfig | 1 + >>> drivers/iio/common/Makefile | 1 + >>> drivers/iio/common/ssp_sensors/Kconfig | 26 ++ >>> drivers/iio/common/ssp_sensors/Makefile | 8 + >>> drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++++++ >>> drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++++++++++++ >>> drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++++++++++ >>> include/linux/iio/common/ssp_sensors.h | 82 ++++ >>> 8 files changed, 1695 insertions(+) >>> create mode 100644 drivers/iio/common/ssp_sensors/Kconfig >>> create mode 100644 drivers/iio/common/ssp_sensors/Makefile >>> create mode 100644 drivers/iio/common/ssp_sensors/ssp.h >>> create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c >>> create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c >>> create mode 100644 include/linux/iio/common/ssp_sensors.h >>> >>> diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig >>> index 0b6e97d..790f106 100644 >>> --- a/drivers/iio/common/Kconfig >>> +++ b/drivers/iio/common/Kconfig >>> @@ -3,4 +3,5 @@ >>> # >>> >>> source "drivers/iio/common/hid-sensors/Kconfig" >>> +source "drivers/iio/common/ssp_sensors/Kconfig" >>> source "drivers/iio/common/st_sensors/Kconfig" >>> diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile >>> index 3112df0..b1e4d9c 100644 >>> --- a/drivers/iio/common/Makefile >>> +++ b/drivers/iio/common/Makefile >>> @@ -8,4 +8,5 @@ >>> >>> # When adding new entries keep the list in alphabetical order >>> obj-y += hid-sensors/ >>> +obj-y += ssp_sensors/ >>> obj-y += st_sensors/ >>> diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig >>> new file mode 100644 >>> index 0000000..0ea4faf >>> --- /dev/null >>> +++ b/drivers/iio/common/ssp_sensors/Kconfig >>> @@ -0,0 +1,26 @@ >>> +# >>> +# SSP sensor drivers and commons configuration >>> +# >>> +menu "SSP Sensor Common" >>> + >>> +config IIO_SSP_SENSORS_COMMONS >>> + tristate "Commons for all SSP Sensor IIO drivers" >>> + depends on IIO_SSP_SENSORHUB >>> + select IIO_BUFFER >>> + select IIO_KFIFO_BUF >>> + help >>> + Say yes here to build commons for SSP sensors. >>> + To compile this as a module, choose M here: the module >>> + will be called ssp_iio. >>> + >>> +config IIO_SSP_SENSORHUB >>> + tristate "Samsung Sensorhub driver" >>> + depends on SPI >>> + select MFD_CORE >>> + help >>> + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. >>> + To compile this driver as a module, choose M here: the >>> + module will be called sensorhub. >>> + >>> +endmenu >>> diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile >>> new file mode 100644 >>> index 0000000..1e0389e >>> --- /dev/null >>> +++ b/drivers/iio/common/ssp_sensors/Makefile >>> @@ -0,0 +1,8 @@ >>> +# >>> +# Makefile for SSP sensor drivers and commons. >>> +# >>> + >>> +sensorhub-objs := ssp_dev.o ssp_spi.o >>> +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o >>> + >>> +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_iio.o >> This file isn't in this patch. > > Thanks for doing that. > I had to mess sth up during rebase. > > [...] > That's fine, I just messed up moving it myself. Forgot the Kconfig bit needed to move patch as well. Anyhow, hopefully the version I push in a few secs will be right! Jonathan ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v5 1/5] iio: common: ssp_sensors: Add sensorhub driver @ 2015-01-29 18:53 ` Jonathan Cameron 0 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:53 UTC (permalink / raw) To: Karol Wrona, linux-iio-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 29/01/15 18:46, Karol Wrona wrote: > On 01/29/2015 07:35 PM, Jonathan Cameron wrote: >> On 28/01/15 14:05, Karol Wrona wrote: >>> Sensorhub is MCU dedicated to collect data and manage several sensors. >>> Sensorhub is a spi device which provides a layer for IIO devices. It provides >>> some data parsing and common mechanism for sensorhub sensors. >>> >>> Adds common sensorhub library for sensorhub driver and iio drivers >>> which uses sensorhub MCU to communicate with sensors. >>> >>> Signed-off-by: Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> >>> Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> >> A couple of build errors from this one... >> >> I've fixed them up and applied to the togreg branch of iio.git. >> Pushed out as testing. If you get a chance to check I didn't >> mess anything up that would be great. >>> --- >>> drivers/iio/common/Kconfig | 1 + >>> drivers/iio/common/Makefile | 1 + >>> drivers/iio/common/ssp_sensors/Kconfig | 26 ++ >>> drivers/iio/common/ssp_sensors/Makefile | 8 + >>> drivers/iio/common/ssp_sensors/ssp.h | 257 +++++++++++ >>> drivers/iio/common/ssp_sensors/ssp_dev.c | 712 ++++++++++++++++++++++++++++++ >>> drivers/iio/common/ssp_sensors/ssp_spi.c | 608 +++++++++++++++++++++++++ >>> include/linux/iio/common/ssp_sensors.h | 82 ++++ >>> 8 files changed, 1695 insertions(+) >>> create mode 100644 drivers/iio/common/ssp_sensors/Kconfig >>> create mode 100644 drivers/iio/common/ssp_sensors/Makefile >>> create mode 100644 drivers/iio/common/ssp_sensors/ssp.h >>> create mode 100644 drivers/iio/common/ssp_sensors/ssp_dev.c >>> create mode 100644 drivers/iio/common/ssp_sensors/ssp_spi.c >>> create mode 100644 include/linux/iio/common/ssp_sensors.h >>> >>> diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig >>> index 0b6e97d..790f106 100644 >>> --- a/drivers/iio/common/Kconfig >>> +++ b/drivers/iio/common/Kconfig >>> @@ -3,4 +3,5 @@ >>> # >>> >>> source "drivers/iio/common/hid-sensors/Kconfig" >>> +source "drivers/iio/common/ssp_sensors/Kconfig" >>> source "drivers/iio/common/st_sensors/Kconfig" >>> diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile >>> index 3112df0..b1e4d9c 100644 >>> --- a/drivers/iio/common/Makefile >>> +++ b/drivers/iio/common/Makefile >>> @@ -8,4 +8,5 @@ >>> >>> # When adding new entries keep the list in alphabetical order >>> obj-y += hid-sensors/ >>> +obj-y += ssp_sensors/ >>> obj-y += st_sensors/ >>> diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig >>> new file mode 100644 >>> index 0000000..0ea4faf >>> --- /dev/null >>> +++ b/drivers/iio/common/ssp_sensors/Kconfig >>> @@ -0,0 +1,26 @@ >>> +# >>> +# SSP sensor drivers and commons configuration >>> +# >>> +menu "SSP Sensor Common" >>> + >>> +config IIO_SSP_SENSORS_COMMONS >>> + tristate "Commons for all SSP Sensor IIO drivers" >>> + depends on IIO_SSP_SENSORHUB >>> + select IIO_BUFFER >>> + select IIO_KFIFO_BUF >>> + help >>> + Say yes here to build commons for SSP sensors. >>> + To compile this as a module, choose M here: the module >>> + will be called ssp_iio. >>> + >>> +config IIO_SSP_SENSORHUB >>> + tristate "Samsung Sensorhub driver" >>> + depends on SPI >>> + select MFD_CORE >>> + help >>> + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. >>> + To compile this driver as a module, choose M here: the >>> + module will be called sensorhub. >>> + >>> +endmenu >>> diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile >>> new file mode 100644 >>> index 0000000..1e0389e >>> --- /dev/null >>> +++ b/drivers/iio/common/ssp_sensors/Makefile >>> @@ -0,0 +1,8 @@ >>> +# >>> +# Makefile for SSP sensor drivers and commons. >>> +# >>> + >>> +sensorhub-objs := ssp_dev.o ssp_spi.o >>> +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o >>> + >>> +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_iio.o >> This file isn't in this patch. > > Thanks for doing that. > I had to mess sth up during rebase. > > [...] > That's fine, I just messed up moving it myself. Forgot the Kconfig bit needed to move patch as well. Anyhow, hopefully the version I push in a few secs will be right! Jonathan ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v5 2/5] iio: sensorhub: Add sensorhub bindings @ 2015-01-28 14:05 ` Karol Wrona 0 siblings, 0 replies; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona Add sensorhub bindings for sensorhub on Galaxy Gear 2. Signed-off-by: Karol Wrona <k.wrona@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> --- .../devicetree/bindings/iio/sensorhub.txt | 25 ++++++++++++++++++++ 1 file changed, 25 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/sensorhub.txt diff --git a/Documentation/devicetree/bindings/iio/sensorhub.txt b/Documentation/devicetree/bindings/iio/sensorhub.txt new file mode 100644 index 0000000..8d57571 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/sensorhub.txt @@ -0,0 +1,25 @@ +Samsung Sensorhub driver + +Sensorhub is a MCU which manages several sensors and also plays the role +of a virtual sensor device. + +Required properties: +- compatible: "samsung,sensorhub-rinato" or "samsung,sensorhub-thermostat" +- spi-max-frequency: max SPI clock frequency +- interrupt-parent: interrupt parent +- interrupts: communication interrupt +- ap-mcu-gpios: [out] ap to sensorhub line - used during communication +- mcu-ap-gpios: [in] sensorhub to ap - used during communication +- mcu-reset-gpios: [out] sensorhub reset + +Example: + + shub_spi: shub { + compatible = "samsung,sensorhub-rinato"; + spi-max-frequency = <5000000>; + interrupt-parent = <&gpx0>; + interrupts = <2 0>; + ap-mcu-gpios = <&gpx0 0 0>; + mcu-ap-gpios = <&gpx0 4 0>; + mcu-reset-gpios = <&gpx0 5 0>; + }; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v5 2/5] iio: sensorhub: Add sensorhub bindings @ 2015-01-28 14:05 ` Karol Wrona 0 siblings, 0 replies; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona Add sensorhub bindings for sensorhub on Galaxy Gear 2. Signed-off-by: Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> --- .../devicetree/bindings/iio/sensorhub.txt | 25 ++++++++++++++++++++ 1 file changed, 25 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/sensorhub.txt diff --git a/Documentation/devicetree/bindings/iio/sensorhub.txt b/Documentation/devicetree/bindings/iio/sensorhub.txt new file mode 100644 index 0000000..8d57571 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/sensorhub.txt @@ -0,0 +1,25 @@ +Samsung Sensorhub driver + +Sensorhub is a MCU which manages several sensors and also plays the role +of a virtual sensor device. + +Required properties: +- compatible: "samsung,sensorhub-rinato" or "samsung,sensorhub-thermostat" +- spi-max-frequency: max SPI clock frequency +- interrupt-parent: interrupt parent +- interrupts: communication interrupt +- ap-mcu-gpios: [out] ap to sensorhub line - used during communication +- mcu-ap-gpios: [in] sensorhub to ap - used during communication +- mcu-reset-gpios: [out] sensorhub reset + +Example: + + shub_spi: shub { + compatible = "samsung,sensorhub-rinato"; + spi-max-frequency = <5000000>; + interrupt-parent = <&gpx0>; + interrupts = <2 0>; + ap-mcu-gpios = <&gpx0 0 0>; + mcu-ap-gpios = <&gpx0 4 0>; + mcu-reset-gpios = <&gpx0 5 0>; + }; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v5 2/5] iio: sensorhub: Add sensorhub bindings 2015-01-28 14:05 ` Karol Wrona (?) @ 2015-01-29 18:36 ` Jonathan Cameron -1 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:36 UTC (permalink / raw) To: Karol Wrona, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > Add sensorhub bindings for sensorhub on Galaxy Gear 2. > > Signed-off-by: Karol Wrona <k.wrona@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> It's simple and hasn't changed in months, so applied to the togreg branch of iio.git. > --- > .../devicetree/bindings/iio/sensorhub.txt | 25 ++++++++++++++++++++ > 1 file changed, 25 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/sensorhub.txt > > diff --git a/Documentation/devicetree/bindings/iio/sensorhub.txt b/Documentation/devicetree/bindings/iio/sensorhub.txt > new file mode 100644 > index 0000000..8d57571 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/sensorhub.txt > @@ -0,0 +1,25 @@ > +Samsung Sensorhub driver > + > +Sensorhub is a MCU which manages several sensors and also plays the role > +of a virtual sensor device. > + > +Required properties: > +- compatible: "samsung,sensorhub-rinato" or "samsung,sensorhub-thermostat" > +- spi-max-frequency: max SPI clock frequency > +- interrupt-parent: interrupt parent > +- interrupts: communication interrupt > +- ap-mcu-gpios: [out] ap to sensorhub line - used during communication > +- mcu-ap-gpios: [in] sensorhub to ap - used during communication > +- mcu-reset-gpios: [out] sensorhub reset > + > +Example: > + > + shub_spi: shub { > + compatible = "samsung,sensorhub-rinato"; > + spi-max-frequency = <5000000>; > + interrupt-parent = <&gpx0>; > + interrupts = <2 0>; > + ap-mcu-gpios = <&gpx0 0 0>; > + mcu-ap-gpios = <&gpx0 4 0>; > + mcu-reset-gpios = <&gpx0 5 0>; > + }; > ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v5 3/5] iio: common: ssp_sensors: Add sensorhub iio commons 2015-01-28 14:05 [PATCH v5 0/5] iio: Add sensorhub driver Karol Wrona 2015-01-28 14:05 ` [PATCH v5 1/5] iio: common: ssp_sensors: " Karol Wrona 2015-01-28 14:05 ` Karol Wrona @ 2015-01-28 14:05 ` Karol Wrona 2015-01-29 18:36 ` Jonathan Cameron 2015-01-28 14:05 ` Karol Wrona 2015-01-28 14:05 ` Karol Wrona 4 siblings, 1 reply; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona This patch adds common library for sensorhub iio drivers. Signed-off-by: Karol Wrona <k.wrona@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> --- drivers/iio/common/ssp_sensors/ssp_iio.c | 107 +++++++++++++++++++++++ drivers/iio/common/ssp_sensors/ssp_iio_sensor.h | 70 +++++++++++++++ 2 files changed, 177 insertions(+) create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio.c create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio_sensor.h diff --git a/drivers/iio/common/ssp_sensors/ssp_iio.c b/drivers/iio/common/ssp_sensors/ssp_iio.c new file mode 100644 index 0000000..a3ae165 --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp_iio.c @@ -0,0 +1,107 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/module.h> +#include <linux/slab.h> +#include "ssp_iio_sensor.h" + +/** + * ssp_common_buffer_postenable() - generic postenable callback for ssp buffer + * + * @indio_dev: iio device + * + * Returns 0 or negative value in case of error + */ +int ssp_common_buffer_postenable(struct iio_dev *indio_dev) +{ + struct ssp_sensor_data *spd = iio_priv(indio_dev); + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + /* the allocation is made in post because scan size is known in this + * moment + * */ + spd->buffer = kmalloc(indio_dev->scan_bytes, GFP_KERNEL | GFP_DMA); + if (!spd->buffer) + return -ENOMEM; + + return ssp_enable_sensor(data, spd->type, + ssp_get_sensor_delay(data, spd->type)); +} +EXPORT_SYMBOL(ssp_common_buffer_postenable); + +/** + * ssp_common_buffer_postdisable() - generic postdisable callback for ssp buffer + * + * @indio_dev: iio device + * + * Returns 0 or negative value in case of error + */ +int ssp_common_buffer_postdisable(struct iio_dev *indio_dev) +{ + int ret; + struct ssp_sensor_data *spd = iio_priv(indio_dev); + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + ret = ssp_disable_sensor(data, spd->type); + if (ret < 0) + return ret; + + kfree(spd->buffer); + + return ret; +} +EXPORT_SYMBOL(ssp_common_buffer_postdisable); + +/** + * ssp_common_process_data() - Common process data callback for ssp sensors + * + * @indio_dev: iio device + * @buf: source buffer + * @len: sensor data length + * @timestamp: system timestamp + * + * Returns 0 or negative value in case of error + */ +int ssp_common_process_data(struct iio_dev *indio_dev, void *buf, + unsigned int len, int64_t timestamp) +{ + __le32 time; + int64_t calculated_time; + struct ssp_sensor_data *spd = iio_priv(indio_dev); + + if (indio_dev->scan_bytes == 0) + return 0; + + /* + * it always sends full set of samples, remember about available masks + */ + memcpy(spd->buffer, buf, len); + + if (indio_dev->scan_timestamp) { + memcpy(&time, &((char *)buf)[len], SSP_TIME_SIZE); + calculated_time = + timestamp + (int64_t)le32_to_cpu(time) * 1000000; + } + + return iio_push_to_buffers_with_timestamp(indio_dev, spd->buffer, + calculated_time); +} +EXPORT_SYMBOL(ssp_common_process_data); + +MODULE_AUTHOR("Karol Wrona <k.wrona@samsung.com>"); +MODULE_DESCRIPTION("Samsung sensorhub commons"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h b/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h new file mode 100644 index 0000000..dda267c --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h @@ -0,0 +1,70 @@ +#ifndef __SSP_IIO_SENSOR_H__ +#define __SSP_IIO_SENSOR_H__ + +#define SSP_CHANNEL_AG(_type, _mod, _index) \ +{ \ + .type = _type,\ + .modified = 1,\ + .channel2 = _mod,\ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),\ + .scan_index = _index,\ + .scan_type = {\ + .sign = 's',\ + .realbits = 16,\ + .storagebits = 16,\ + .shift = 0,\ + .endianness = IIO_LE,\ + },\ +} + +/* It is defined here as it is a mixed timestamp */ +#define SSP_CHAN_TIMESTAMP(_si) { \ + .type = IIO_TIMESTAMP, \ + .channel = -1, \ + .scan_index = _si, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 64, \ + .storagebits = 64, \ + }, \ +} + +#define SSP_MS_PER_S 1000 +#define SSP_INVERTED_SCALING_FACTOR 1000000ULL + +#define SSP_FACTOR_WITH_MS \ + (SSP_INVERTED_SCALING_FACTOR * SSP_MS_PER_S) + +int ssp_common_buffer_postenable(struct iio_dev *indio_dev); + +int ssp_common_buffer_postdisable(struct iio_dev *indio_dev); + +int ssp_common_process_data(struct iio_dev *indio_dev, void *buf, + unsigned int len, int64_t timestamp); + +/* Converts time in ms to frequency */ +static inline void ssp_convert_to_freq(u32 time, int *integer_part, + int *fractional) +{ + if (time == 0) { + *fractional = 0; + *integer_part = 0; + return; + } + + *integer_part = SSP_FACTOR_WITH_MS / time; + *fractional = do_div(*integer_part, SSP_INVERTED_SCALING_FACTOR); +} + +/* Converts frequency to time in ms */ +static inline int ssp_convert_to_time(int integer_part, int fractional) +{ + u64 value; + + value = integer_part * SSP_INVERTED_SCALING_FACTOR + fractional; + if (value == 0) + return 0; + + return div_u64(SSP_FACTOR_WITH_MS, value); +} +#endif /* __SSP_IIO_SENSOR_H__ */ -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v5 3/5] iio: common: ssp_sensors: Add sensorhub iio commons @ 2015-01-29 18:36 ` Jonathan Cameron 0 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:36 UTC (permalink / raw) To: Karol Wrona, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > This patch adds common library for sensorhub iio drivers. > > Signed-off-by: Karol Wrona <k.wrona@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Applied with the make file line brought forward from patch 1. Pushed out as testing for the autobuilders to play. > --- > drivers/iio/common/ssp_sensors/ssp_iio.c | 107 +++++++++++++++++++++++ > drivers/iio/common/ssp_sensors/ssp_iio_sensor.h | 70 +++++++++++++++ > 2 files changed, 177 insertions(+) > create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio.c > create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio_sensor.h > > diff --git a/drivers/iio/common/ssp_sensors/ssp_iio.c b/drivers/iio/common/ssp_sensors/ssp_iio.c > new file mode 100644 > index 0000000..a3ae165 > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_iio.c > @@ -0,0 +1,107 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/iio/common/ssp_sensors.h> > +#include <linux/iio/kfifo_buf.h> > +#include <linux/module.h> > +#include <linux/slab.h> > +#include "ssp_iio_sensor.h" > + > +/** > + * ssp_common_buffer_postenable() - generic postenable callback for ssp buffer > + * > + * @indio_dev: iio device > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_common_buffer_postenable(struct iio_dev *indio_dev) > +{ > + struct ssp_sensor_data *spd = iio_priv(indio_dev); > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + /* the allocation is made in post because scan size is known in this > + * moment > + * */ > + spd->buffer = kmalloc(indio_dev->scan_bytes, GFP_KERNEL | GFP_DMA); > + if (!spd->buffer) > + return -ENOMEM; > + > + return ssp_enable_sensor(data, spd->type, > + ssp_get_sensor_delay(data, spd->type)); > +} > +EXPORT_SYMBOL(ssp_common_buffer_postenable); > + > +/** > + * ssp_common_buffer_postdisable() - generic postdisable callback for ssp buffer > + * > + * @indio_dev: iio device > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_common_buffer_postdisable(struct iio_dev *indio_dev) > +{ > + int ret; > + struct ssp_sensor_data *spd = iio_priv(indio_dev); > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + ret = ssp_disable_sensor(data, spd->type); > + if (ret < 0) > + return ret; > + > + kfree(spd->buffer); > + > + return ret; > +} > +EXPORT_SYMBOL(ssp_common_buffer_postdisable); > + > +/** > + * ssp_common_process_data() - Common process data callback for ssp sensors > + * > + * @indio_dev: iio device > + * @buf: source buffer > + * @len: sensor data length > + * @timestamp: system timestamp > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_common_process_data(struct iio_dev *indio_dev, void *buf, > + unsigned int len, int64_t timestamp) > +{ > + __le32 time; > + int64_t calculated_time; > + struct ssp_sensor_data *spd = iio_priv(indio_dev); > + > + if (indio_dev->scan_bytes == 0) > + return 0; > + > + /* > + * it always sends full set of samples, remember about available masks > + */ > + memcpy(spd->buffer, buf, len); > + > + if (indio_dev->scan_timestamp) { > + memcpy(&time, &((char *)buf)[len], SSP_TIME_SIZE); > + calculated_time = > + timestamp + (int64_t)le32_to_cpu(time) * 1000000; > + } > + > + return iio_push_to_buffers_with_timestamp(indio_dev, spd->buffer, > + calculated_time); > +} > +EXPORT_SYMBOL(ssp_common_process_data); > + > +MODULE_AUTHOR("Karol Wrona <k.wrona@samsung.com>"); > +MODULE_DESCRIPTION("Samsung sensorhub commons"); > +MODULE_LICENSE("GPL"); > diff --git a/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h b/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h > new file mode 100644 > index 0000000..dda267c > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h > @@ -0,0 +1,70 @@ > +#ifndef __SSP_IIO_SENSOR_H__ > +#define __SSP_IIO_SENSOR_H__ > + > +#define SSP_CHANNEL_AG(_type, _mod, _index) \ > +{ \ > + .type = _type,\ > + .modified = 1,\ > + .channel2 = _mod,\ > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),\ > + .scan_index = _index,\ > + .scan_type = {\ > + .sign = 's',\ > + .realbits = 16,\ > + .storagebits = 16,\ > + .shift = 0,\ > + .endianness = IIO_LE,\ > + },\ > +} > + > +/* It is defined here as it is a mixed timestamp */ > +#define SSP_CHAN_TIMESTAMP(_si) { \ > + .type = IIO_TIMESTAMP, \ > + .channel = -1, \ > + .scan_index = _si, \ > + .scan_type = { \ > + .sign = 's', \ > + .realbits = 64, \ > + .storagebits = 64, \ > + }, \ > +} > + > +#define SSP_MS_PER_S 1000 > +#define SSP_INVERTED_SCALING_FACTOR 1000000ULL > + > +#define SSP_FACTOR_WITH_MS \ > + (SSP_INVERTED_SCALING_FACTOR * SSP_MS_PER_S) > + > +int ssp_common_buffer_postenable(struct iio_dev *indio_dev); > + > +int ssp_common_buffer_postdisable(struct iio_dev *indio_dev); > + > +int ssp_common_process_data(struct iio_dev *indio_dev, void *buf, > + unsigned int len, int64_t timestamp); > + > +/* Converts time in ms to frequency */ > +static inline void ssp_convert_to_freq(u32 time, int *integer_part, > + int *fractional) > +{ > + if (time == 0) { > + *fractional = 0; > + *integer_part = 0; > + return; > + } > + > + *integer_part = SSP_FACTOR_WITH_MS / time; > + *fractional = do_div(*integer_part, SSP_INVERTED_SCALING_FACTOR); > +} > + > +/* Converts frequency to time in ms */ > +static inline int ssp_convert_to_time(int integer_part, int fractional) > +{ > + u64 value; > + > + value = integer_part * SSP_INVERTED_SCALING_FACTOR + fractional; > + if (value == 0) > + return 0; > + > + return div_u64(SSP_FACTOR_WITH_MS, value); > +} > +#endif /* __SSP_IIO_SENSOR_H__ */ > ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v5 3/5] iio: common: ssp_sensors: Add sensorhub iio commons @ 2015-01-29 18:36 ` Jonathan Cameron 0 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:36 UTC (permalink / raw) To: Karol Wrona, linux-iio-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > This patch adds common library for sensorhub iio drivers. > > Signed-off-by: Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> > Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> Applied with the make file line brought forward from patch 1. Pushed out as testing for the autobuilders to play. > --- > drivers/iio/common/ssp_sensors/ssp_iio.c | 107 +++++++++++++++++++++++ > drivers/iio/common/ssp_sensors/ssp_iio_sensor.h | 70 +++++++++++++++ > 2 files changed, 177 insertions(+) > create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio.c > create mode 100644 drivers/iio/common/ssp_sensors/ssp_iio_sensor.h > > diff --git a/drivers/iio/common/ssp_sensors/ssp_iio.c b/drivers/iio/common/ssp_sensors/ssp_iio.c > new file mode 100644 > index 0000000..a3ae165 > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_iio.c > @@ -0,0 +1,107 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/iio/common/ssp_sensors.h> > +#include <linux/iio/kfifo_buf.h> > +#include <linux/module.h> > +#include <linux/slab.h> > +#include "ssp_iio_sensor.h" > + > +/** > + * ssp_common_buffer_postenable() - generic postenable callback for ssp buffer > + * > + * @indio_dev: iio device > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_common_buffer_postenable(struct iio_dev *indio_dev) > +{ > + struct ssp_sensor_data *spd = iio_priv(indio_dev); > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + /* the allocation is made in post because scan size is known in this > + * moment > + * */ > + spd->buffer = kmalloc(indio_dev->scan_bytes, GFP_KERNEL | GFP_DMA); > + if (!spd->buffer) > + return -ENOMEM; > + > + return ssp_enable_sensor(data, spd->type, > + ssp_get_sensor_delay(data, spd->type)); > +} > +EXPORT_SYMBOL(ssp_common_buffer_postenable); > + > +/** > + * ssp_common_buffer_postdisable() - generic postdisable callback for ssp buffer > + * > + * @indio_dev: iio device > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_common_buffer_postdisable(struct iio_dev *indio_dev) > +{ > + int ret; > + struct ssp_sensor_data *spd = iio_priv(indio_dev); > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + ret = ssp_disable_sensor(data, spd->type); > + if (ret < 0) > + return ret; > + > + kfree(spd->buffer); > + > + return ret; > +} > +EXPORT_SYMBOL(ssp_common_buffer_postdisable); > + > +/** > + * ssp_common_process_data() - Common process data callback for ssp sensors > + * > + * @indio_dev: iio device > + * @buf: source buffer > + * @len: sensor data length > + * @timestamp: system timestamp > + * > + * Returns 0 or negative value in case of error > + */ > +int ssp_common_process_data(struct iio_dev *indio_dev, void *buf, > + unsigned int len, int64_t timestamp) > +{ > + __le32 time; > + int64_t calculated_time; > + struct ssp_sensor_data *spd = iio_priv(indio_dev); > + > + if (indio_dev->scan_bytes == 0) > + return 0; > + > + /* > + * it always sends full set of samples, remember about available masks > + */ > + memcpy(spd->buffer, buf, len); > + > + if (indio_dev->scan_timestamp) { > + memcpy(&time, &((char *)buf)[len], SSP_TIME_SIZE); > + calculated_time = > + timestamp + (int64_t)le32_to_cpu(time) * 1000000; > + } > + > + return iio_push_to_buffers_with_timestamp(indio_dev, spd->buffer, > + calculated_time); > +} > +EXPORT_SYMBOL(ssp_common_process_data); > + > +MODULE_AUTHOR("Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>"); > +MODULE_DESCRIPTION("Samsung sensorhub commons"); > +MODULE_LICENSE("GPL"); > diff --git a/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h b/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h > new file mode 100644 > index 0000000..dda267c > --- /dev/null > +++ b/drivers/iio/common/ssp_sensors/ssp_iio_sensor.h > @@ -0,0 +1,70 @@ > +#ifndef __SSP_IIO_SENSOR_H__ > +#define __SSP_IIO_SENSOR_H__ > + > +#define SSP_CHANNEL_AG(_type, _mod, _index) \ > +{ \ > + .type = _type,\ > + .modified = 1,\ > + .channel2 = _mod,\ > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),\ > + .scan_index = _index,\ > + .scan_type = {\ > + .sign = 's',\ > + .realbits = 16,\ > + .storagebits = 16,\ > + .shift = 0,\ > + .endianness = IIO_LE,\ > + },\ > +} > + > +/* It is defined here as it is a mixed timestamp */ > +#define SSP_CHAN_TIMESTAMP(_si) { \ > + .type = IIO_TIMESTAMP, \ > + .channel = -1, \ > + .scan_index = _si, \ > + .scan_type = { \ > + .sign = 's', \ > + .realbits = 64, \ > + .storagebits = 64, \ > + }, \ > +} > + > +#define SSP_MS_PER_S 1000 > +#define SSP_INVERTED_SCALING_FACTOR 1000000ULL > + > +#define SSP_FACTOR_WITH_MS \ > + (SSP_INVERTED_SCALING_FACTOR * SSP_MS_PER_S) > + > +int ssp_common_buffer_postenable(struct iio_dev *indio_dev); > + > +int ssp_common_buffer_postdisable(struct iio_dev *indio_dev); > + > +int ssp_common_process_data(struct iio_dev *indio_dev, void *buf, > + unsigned int len, int64_t timestamp); > + > +/* Converts time in ms to frequency */ > +static inline void ssp_convert_to_freq(u32 time, int *integer_part, > + int *fractional) > +{ > + if (time == 0) { > + *fractional = 0; > + *integer_part = 0; > + return; > + } > + > + *integer_part = SSP_FACTOR_WITH_MS / time; > + *fractional = do_div(*integer_part, SSP_INVERTED_SCALING_FACTOR); > +} > + > +/* Converts frequency to time in ms */ > +static inline int ssp_convert_to_time(int integer_part, int fractional) > +{ > + u64 value; > + > + value = integer_part * SSP_INVERTED_SCALING_FACTOR + fractional; > + if (value == 0) > + return 0; > + > + return div_u64(SSP_FACTOR_WITH_MS, value); > +} > +#endif /* __SSP_IIO_SENSOR_H__ */ > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v5 4/5] iio: common: ssp_sensors: Add sensorhub accelerometer sensor @ 2015-01-28 14:05 ` Karol Wrona 0 siblings, 0 replies; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona This patch adds accelerometer iio driver which uses sensorhub as data provider. Signed-off-by: Karol Wrona <k.wrona@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> --- drivers/iio/accel/Makefile | 1 + drivers/iio/accel/ssp_accel_sensor.c | 169 ++++++++++++++++++++++++++++++++++ 2 files changed, 170 insertions(+) create mode 100644 drivers/iio/accel/ssp_accel_sensor.c diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index de5b9cb..69c64b6 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o obj-$(CONFIG_KXSD9) += kxsd9.o obj-$(CONFIG_MMA8452) += mma8452.o obj-$(CONFIG_MMA9551) += mma9551.o +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_accel_sensor.o obj-$(CONFIG_IIO_ST_ACCEL_3AXIS) += st_accel.o st_accel-y := st_accel_core.o diff --git a/drivers/iio/accel/ssp_accel_sensor.c b/drivers/iio/accel/ssp_accel_sensor.c new file mode 100644 index 0000000..4ae05fc --- /dev/null +++ b/drivers/iio/accel/ssp_accel_sensor.c @@ -0,0 +1,169 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/iio.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include "../common/ssp_sensors/ssp_iio_sensor.h" + +#define SSP_CHANNEL_COUNT 3 + +#define SSP_ACCEL_NAME "ssp-accelerometer" +static const char ssp_accel_device_name[] = SSP_ACCEL_NAME; + +enum ssp_accel_3d_channel { + SSP_CHANNEL_SCAN_INDEX_X, + SSP_CHANNEL_SCAN_INDEX_Y, + SSP_CHANNEL_SCAN_INDEX_Z, + SSP_CHANNEL_SCAN_INDEX_TIME, +}; + +static int ssp_accel_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int *val, + int *val2, long mask) +{ + u32 t; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + t = ssp_get_sensor_delay(data, SSP_ACCELEROMETER_SENSOR); + ssp_convert_to_freq(t, val, val2); + return IIO_VAL_INT_PLUS_MICRO; + default: + break; + } + + return -EINVAL; +} + +static int ssp_accel_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int val, + int val2, long mask) +{ + int ret; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + ret = ssp_convert_to_time(val, val2); + ret = ssp_change_delay(data, SSP_ACCELEROMETER_SENSOR, ret); + if (ret < 0) + dev_err(&indio_dev->dev, "accel sensor enable fail\n"); + + return ret; + default: + break; + } + + return -EINVAL; +} + +static struct iio_info ssp_accel_iio_info = { + .read_raw = &ssp_accel_read_raw, + .write_raw = &ssp_accel_write_raw, +}; + +static const unsigned long ssp_accel_scan_mask[] = { 0x7, 0, }; + +static const struct iio_chan_spec ssp_acc_channels[] = { + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_X, SSP_CHANNEL_SCAN_INDEX_X), + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_Y, SSP_CHANNEL_SCAN_INDEX_Y), + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_Z, SSP_CHANNEL_SCAN_INDEX_Z), + SSP_CHAN_TIMESTAMP(SSP_CHANNEL_SCAN_INDEX_TIME), +}; + +static int ssp_process_accel_data(struct iio_dev *indio_dev, void *buf, + int64_t timestamp) +{ + return ssp_common_process_data(indio_dev, buf, SSP_ACCELEROMETER_SIZE, + timestamp); +} + +static const struct iio_buffer_setup_ops ssp_accel_buffer_ops = { + .postenable = &ssp_common_buffer_postenable, + .postdisable = &ssp_common_buffer_postdisable, +}; + +static int ssp_accel_probe(struct platform_device *pdev) +{ + int ret; + struct iio_dev *indio_dev; + struct ssp_sensor_data *spd; + struct iio_buffer *buffer; + + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*spd)); + if (!indio_dev) + return -ENOMEM; + + spd = iio_priv(indio_dev); + + spd->process_data = ssp_process_accel_data; + spd->type = SSP_ACCELEROMETER_SENSOR; + + indio_dev->name = ssp_accel_device_name; + indio_dev->dev.parent = &pdev->dev; + indio_dev->dev.of_node = pdev->dev.of_node; + indio_dev->info = &ssp_accel_iio_info; + indio_dev->modes = INDIO_BUFFER_SOFTWARE; + indio_dev->channels = ssp_acc_channels; + indio_dev->num_channels = ARRAY_SIZE(ssp_acc_channels); + indio_dev->available_scan_masks = ssp_accel_scan_mask; + + buffer = devm_iio_kfifo_allocate(&pdev->dev); + if (!buffer) + return -ENOMEM; + + iio_device_attach_buffer(indio_dev, buffer); + + indio_dev->setup_ops = &ssp_accel_buffer_ops; + + platform_set_drvdata(pdev, indio_dev); + + ret = iio_device_register(indio_dev); + if (ret < 0) + return ret; + + /* ssp registering should be done after all iio setup */ + ssp_register_consumer(indio_dev, SSP_ACCELEROMETER_SENSOR); + + return 0; +} + +static int ssp_accel_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + + iio_device_unregister(indio_dev); + + return 0; +} + +static struct platform_driver ssp_accel_driver = { + .driver = { + .name = SSP_ACCEL_NAME, + }, + .probe = ssp_accel_probe, + .remove = ssp_accel_remove, +}; + +module_platform_driver(ssp_accel_driver); + +MODULE_AUTHOR("Karol Wrona <k.wrona@samsung.com>"); +MODULE_DESCRIPTION("Samsung sensorhub accelerometers driver"); +MODULE_LICENSE("GPL"); -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v5 4/5] iio: common: ssp_sensors: Add sensorhub accelerometer sensor @ 2015-01-28 14:05 ` Karol Wrona 0 siblings, 0 replies; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona This patch adds accelerometer iio driver which uses sensorhub as data provider. Signed-off-by: Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> --- drivers/iio/accel/Makefile | 1 + drivers/iio/accel/ssp_accel_sensor.c | 169 ++++++++++++++++++++++++++++++++++ 2 files changed, 170 insertions(+) create mode 100644 drivers/iio/accel/ssp_accel_sensor.c diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index de5b9cb..69c64b6 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o obj-$(CONFIG_KXSD9) += kxsd9.o obj-$(CONFIG_MMA8452) += mma8452.o obj-$(CONFIG_MMA9551) += mma9551.o +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_accel_sensor.o obj-$(CONFIG_IIO_ST_ACCEL_3AXIS) += st_accel.o st_accel-y := st_accel_core.o diff --git a/drivers/iio/accel/ssp_accel_sensor.c b/drivers/iio/accel/ssp_accel_sensor.c new file mode 100644 index 0000000..4ae05fc --- /dev/null +++ b/drivers/iio/accel/ssp_accel_sensor.c @@ -0,0 +1,169 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/iio.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include "../common/ssp_sensors/ssp_iio_sensor.h" + +#define SSP_CHANNEL_COUNT 3 + +#define SSP_ACCEL_NAME "ssp-accelerometer" +static const char ssp_accel_device_name[] = SSP_ACCEL_NAME; + +enum ssp_accel_3d_channel { + SSP_CHANNEL_SCAN_INDEX_X, + SSP_CHANNEL_SCAN_INDEX_Y, + SSP_CHANNEL_SCAN_INDEX_Z, + SSP_CHANNEL_SCAN_INDEX_TIME, +}; + +static int ssp_accel_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int *val, + int *val2, long mask) +{ + u32 t; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + t = ssp_get_sensor_delay(data, SSP_ACCELEROMETER_SENSOR); + ssp_convert_to_freq(t, val, val2); + return IIO_VAL_INT_PLUS_MICRO; + default: + break; + } + + return -EINVAL; +} + +static int ssp_accel_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int val, + int val2, long mask) +{ + int ret; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + ret = ssp_convert_to_time(val, val2); + ret = ssp_change_delay(data, SSP_ACCELEROMETER_SENSOR, ret); + if (ret < 0) + dev_err(&indio_dev->dev, "accel sensor enable fail\n"); + + return ret; + default: + break; + } + + return -EINVAL; +} + +static struct iio_info ssp_accel_iio_info = { + .read_raw = &ssp_accel_read_raw, + .write_raw = &ssp_accel_write_raw, +}; + +static const unsigned long ssp_accel_scan_mask[] = { 0x7, 0, }; + +static const struct iio_chan_spec ssp_acc_channels[] = { + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_X, SSP_CHANNEL_SCAN_INDEX_X), + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_Y, SSP_CHANNEL_SCAN_INDEX_Y), + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_Z, SSP_CHANNEL_SCAN_INDEX_Z), + SSP_CHAN_TIMESTAMP(SSP_CHANNEL_SCAN_INDEX_TIME), +}; + +static int ssp_process_accel_data(struct iio_dev *indio_dev, void *buf, + int64_t timestamp) +{ + return ssp_common_process_data(indio_dev, buf, SSP_ACCELEROMETER_SIZE, + timestamp); +} + +static const struct iio_buffer_setup_ops ssp_accel_buffer_ops = { + .postenable = &ssp_common_buffer_postenable, + .postdisable = &ssp_common_buffer_postdisable, +}; + +static int ssp_accel_probe(struct platform_device *pdev) +{ + int ret; + struct iio_dev *indio_dev; + struct ssp_sensor_data *spd; + struct iio_buffer *buffer; + + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*spd)); + if (!indio_dev) + return -ENOMEM; + + spd = iio_priv(indio_dev); + + spd->process_data = ssp_process_accel_data; + spd->type = SSP_ACCELEROMETER_SENSOR; + + indio_dev->name = ssp_accel_device_name; + indio_dev->dev.parent = &pdev->dev; + indio_dev->dev.of_node = pdev->dev.of_node; + indio_dev->info = &ssp_accel_iio_info; + indio_dev->modes = INDIO_BUFFER_SOFTWARE; + indio_dev->channels = ssp_acc_channels; + indio_dev->num_channels = ARRAY_SIZE(ssp_acc_channels); + indio_dev->available_scan_masks = ssp_accel_scan_mask; + + buffer = devm_iio_kfifo_allocate(&pdev->dev); + if (!buffer) + return -ENOMEM; + + iio_device_attach_buffer(indio_dev, buffer); + + indio_dev->setup_ops = &ssp_accel_buffer_ops; + + platform_set_drvdata(pdev, indio_dev); + + ret = iio_device_register(indio_dev); + if (ret < 0) + return ret; + + /* ssp registering should be done after all iio setup */ + ssp_register_consumer(indio_dev, SSP_ACCELEROMETER_SENSOR); + + return 0; +} + +static int ssp_accel_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + + iio_device_unregister(indio_dev); + + return 0; +} + +static struct platform_driver ssp_accel_driver = { + .driver = { + .name = SSP_ACCEL_NAME, + }, + .probe = ssp_accel_probe, + .remove = ssp_accel_remove, +}; + +module_platform_driver(ssp_accel_driver); + +MODULE_AUTHOR("Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>"); +MODULE_DESCRIPTION("Samsung sensorhub accelerometers driver"); +MODULE_LICENSE("GPL"); -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v5 4/5] iio: common: ssp_sensors: Add sensorhub accelerometer sensor 2015-01-28 14:05 ` Karol Wrona (?) @ 2015-01-29 18:37 ` Jonathan Cameron -1 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:37 UTC (permalink / raw) To: Karol Wrona, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > This patch adds accelerometer iio driver which uses sensorhub as data > provider. > > Signed-off-by: Karol Wrona <k.wrona@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Applied > --- > drivers/iio/accel/Makefile | 1 + > drivers/iio/accel/ssp_accel_sensor.c | 169 ++++++++++++++++++++++++++++++++++ > 2 files changed, 170 insertions(+) > create mode 100644 drivers/iio/accel/ssp_accel_sensor.c > > diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile > index de5b9cb..69c64b6 100644 > --- a/drivers/iio/accel/Makefile > +++ b/drivers/iio/accel/Makefile > @@ -10,6 +10,7 @@ obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o > obj-$(CONFIG_KXSD9) += kxsd9.o > obj-$(CONFIG_MMA8452) += mma8452.o > obj-$(CONFIG_MMA9551) += mma9551.o > +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_accel_sensor.o > > obj-$(CONFIG_IIO_ST_ACCEL_3AXIS) += st_accel.o > st_accel-y := st_accel_core.o > diff --git a/drivers/iio/accel/ssp_accel_sensor.c b/drivers/iio/accel/ssp_accel_sensor.c > new file mode 100644 > index 0000000..4ae05fc > --- /dev/null > +++ b/drivers/iio/accel/ssp_accel_sensor.c > @@ -0,0 +1,169 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/iio/common/ssp_sensors.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/kfifo_buf.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/slab.h> > +#include "../common/ssp_sensors/ssp_iio_sensor.h" > + > +#define SSP_CHANNEL_COUNT 3 > + > +#define SSP_ACCEL_NAME "ssp-accelerometer" > +static const char ssp_accel_device_name[] = SSP_ACCEL_NAME; > + > +enum ssp_accel_3d_channel { > + SSP_CHANNEL_SCAN_INDEX_X, > + SSP_CHANNEL_SCAN_INDEX_Y, > + SSP_CHANNEL_SCAN_INDEX_Z, > + SSP_CHANNEL_SCAN_INDEX_TIME, > +}; > + > +static int ssp_accel_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, int *val, > + int *val2, long mask) > +{ > + u32 t; > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + switch (mask) { > + case IIO_CHAN_INFO_SAMP_FREQ: > + t = ssp_get_sensor_delay(data, SSP_ACCELEROMETER_SENSOR); > + ssp_convert_to_freq(t, val, val2); > + return IIO_VAL_INT_PLUS_MICRO; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int ssp_accel_write_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, int val, > + int val2, long mask) > +{ > + int ret; > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + switch (mask) { > + case IIO_CHAN_INFO_SAMP_FREQ: > + ret = ssp_convert_to_time(val, val2); > + ret = ssp_change_delay(data, SSP_ACCELEROMETER_SENSOR, ret); > + if (ret < 0) > + dev_err(&indio_dev->dev, "accel sensor enable fail\n"); > + > + return ret; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static struct iio_info ssp_accel_iio_info = { > + .read_raw = &ssp_accel_read_raw, > + .write_raw = &ssp_accel_write_raw, > +}; > + > +static const unsigned long ssp_accel_scan_mask[] = { 0x7, 0, }; > + > +static const struct iio_chan_spec ssp_acc_channels[] = { > + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_X, SSP_CHANNEL_SCAN_INDEX_X), > + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_Y, SSP_CHANNEL_SCAN_INDEX_Y), > + SSP_CHANNEL_AG(IIO_ACCEL, IIO_MOD_Z, SSP_CHANNEL_SCAN_INDEX_Z), > + SSP_CHAN_TIMESTAMP(SSP_CHANNEL_SCAN_INDEX_TIME), > +}; > + > +static int ssp_process_accel_data(struct iio_dev *indio_dev, void *buf, > + int64_t timestamp) > +{ > + return ssp_common_process_data(indio_dev, buf, SSP_ACCELEROMETER_SIZE, > + timestamp); > +} > + > +static const struct iio_buffer_setup_ops ssp_accel_buffer_ops = { > + .postenable = &ssp_common_buffer_postenable, > + .postdisable = &ssp_common_buffer_postdisable, > +}; > + > +static int ssp_accel_probe(struct platform_device *pdev) > +{ > + int ret; > + struct iio_dev *indio_dev; > + struct ssp_sensor_data *spd; > + struct iio_buffer *buffer; > + > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*spd)); > + if (!indio_dev) > + return -ENOMEM; > + > + spd = iio_priv(indio_dev); > + > + spd->process_data = ssp_process_accel_data; > + spd->type = SSP_ACCELEROMETER_SENSOR; > + > + indio_dev->name = ssp_accel_device_name; > + indio_dev->dev.parent = &pdev->dev; > + indio_dev->dev.of_node = pdev->dev.of_node; > + indio_dev->info = &ssp_accel_iio_info; > + indio_dev->modes = INDIO_BUFFER_SOFTWARE; > + indio_dev->channels = ssp_acc_channels; > + indio_dev->num_channels = ARRAY_SIZE(ssp_acc_channels); > + indio_dev->available_scan_masks = ssp_accel_scan_mask; > + > + buffer = devm_iio_kfifo_allocate(&pdev->dev); > + if (!buffer) > + return -ENOMEM; > + > + iio_device_attach_buffer(indio_dev, buffer); > + > + indio_dev->setup_ops = &ssp_accel_buffer_ops; > + > + platform_set_drvdata(pdev, indio_dev); > + > + ret = iio_device_register(indio_dev); > + if (ret < 0) > + return ret; > + > + /* ssp registering should be done after all iio setup */ > + ssp_register_consumer(indio_dev, SSP_ACCELEROMETER_SENSOR); > + > + return 0; > +} > + > +static int ssp_accel_remove(struct platform_device *pdev) > +{ > + struct iio_dev *indio_dev = platform_get_drvdata(pdev); > + > + iio_device_unregister(indio_dev); > + > + return 0; > +} > + > +static struct platform_driver ssp_accel_driver = { > + .driver = { > + .name = SSP_ACCEL_NAME, > + }, > + .probe = ssp_accel_probe, > + .remove = ssp_accel_remove, > +}; > + > +module_platform_driver(ssp_accel_driver); > + > +MODULE_AUTHOR("Karol Wrona <k.wrona@samsung.com>"); > +MODULE_DESCRIPTION("Samsung sensorhub accelerometers driver"); > +MODULE_LICENSE("GPL"); > ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v5 5/5] iio: common: ssp_sensors: Add sensorhub gyroscope sensor @ 2015-01-28 14:05 ` Karol Wrona 0 siblings, 0 replies; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona This patch adds gyroscope iio driver which uses sensorhub as data provider. Signed-off-by: Karol Wrona <k.wrona@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> --- drivers/iio/gyro/Makefile | 2 + drivers/iio/gyro/ssp_gyro_sensor.c | 168 ++++++++++++++++++++++++++++++++++++ 2 files changed, 170 insertions(+) create mode 100644 drivers/iio/gyro/ssp_gyro_sensor.c diff --git a/drivers/iio/gyro/Makefile b/drivers/iio/gyro/Makefile index 36a3877..f46341b 100644 --- a/drivers/iio/gyro/Makefile +++ b/drivers/iio/gyro/Makefile @@ -16,6 +16,8 @@ itg3200-y := itg3200_core.o itg3200-$(CONFIG_IIO_BUFFER) += itg3200_buffer.o obj-$(CONFIG_ITG3200) += itg3200.o +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_gyro_sensor.o + obj-$(CONFIG_IIO_ST_GYRO_3AXIS) += st_gyro.o st_gyro-y := st_gyro_core.o st_gyro-$(CONFIG_IIO_BUFFER) += st_gyro_buffer.o diff --git a/drivers/iio/gyro/ssp_gyro_sensor.c b/drivers/iio/gyro/ssp_gyro_sensor.c new file mode 100644 index 0000000..0a8afdd --- /dev/null +++ b/drivers/iio/gyro/ssp_gyro_sensor.c @@ -0,0 +1,168 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/iio.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include "../common/ssp_sensors/ssp_iio_sensor.h" + +#define SSP_CHANNEL_COUNT 3 + +#define SSP_GYROSCOPE_NAME "ssp-gyroscope" +static const char ssp_gyro_name[] = SSP_GYROSCOPE_NAME; + +enum ssp_gyro_3d_channel { + SSP_CHANNEL_SCAN_INDEX_X, + SSP_CHANNEL_SCAN_INDEX_Y, + SSP_CHANNEL_SCAN_INDEX_Z, + SSP_CHANNEL_SCAN_INDEX_TIME, +}; + +static int ssp_gyro_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int *val, + int *val2, long mask) +{ + u32 t; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + t = ssp_get_sensor_delay(data, SSP_GYROSCOPE_SENSOR); + ssp_convert_to_freq(t, val, val2); + return IIO_VAL_INT_PLUS_MICRO; + default: + break; + } + + return -EINVAL; +} + +static int ssp_gyro_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int val, + int val2, long mask) +{ + int ret; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + ret = ssp_convert_to_time(val, val2); + ret = ssp_change_delay(data, SSP_GYROSCOPE_SENSOR, ret); + if (ret < 0) + dev_err(&indio_dev->dev, "gyro sensor enable fail\n"); + + return ret; + default: + break; + } + + return -EINVAL; +} + +static struct iio_info ssp_gyro_iio_info = { + .read_raw = &ssp_gyro_read_raw, + .write_raw = &ssp_gyro_write_raw, +}; + +static const unsigned long ssp_gyro_scan_mask[] = { 0x07, 0, }; + +static const struct iio_chan_spec ssp_gyro_channels[] = { + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_X, SSP_CHANNEL_SCAN_INDEX_X), + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_Y, SSP_CHANNEL_SCAN_INDEX_Y), + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_Z, SSP_CHANNEL_SCAN_INDEX_Z), + SSP_CHAN_TIMESTAMP(SSP_CHANNEL_SCAN_INDEX_TIME), +}; + +static int ssp_process_gyro_data(struct iio_dev *indio_dev, void *buf, + int64_t timestamp) +{ + return ssp_common_process_data(indio_dev, buf, SSP_GYROSCOPE_SIZE, + timestamp); +} + +static const struct iio_buffer_setup_ops ssp_gyro_buffer_ops = { + .postenable = &ssp_common_buffer_postenable, + .postdisable = &ssp_common_buffer_postdisable, +}; + +static int ssp_gyro_probe(struct platform_device *pdev) +{ + int ret; + struct iio_dev *indio_dev; + struct ssp_sensor_data *spd; + struct iio_buffer *buffer; + + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*spd)); + if (!indio_dev) + return -ENOMEM; + + spd = iio_priv(indio_dev); + + spd->process_data = ssp_process_gyro_data; + spd->type = SSP_GYROSCOPE_SENSOR; + + indio_dev->name = ssp_gyro_name; + indio_dev->dev.parent = &pdev->dev; + indio_dev->info = &ssp_gyro_iio_info; + indio_dev->modes = INDIO_BUFFER_SOFTWARE; + indio_dev->channels = ssp_gyro_channels; + indio_dev->num_channels = ARRAY_SIZE(ssp_gyro_channels); + indio_dev->available_scan_masks = ssp_gyro_scan_mask; + + buffer = devm_iio_kfifo_allocate(&pdev->dev); + if (!buffer) + return -ENOMEM; + + iio_device_attach_buffer(indio_dev, buffer); + + indio_dev->setup_ops = &ssp_gyro_buffer_ops; + + platform_set_drvdata(pdev, indio_dev); + + ret = iio_device_register(indio_dev); + if (ret < 0) + return ret; + + /* ssp registering should be done after all iio setup */ + ssp_register_consumer(indio_dev, SSP_GYROSCOPE_SENSOR); + + return 0; +} + +static int ssp_gyro_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + + iio_device_unregister(indio_dev); + + return 0; +} + +static struct platform_driver ssp_gyro_driver = { + .driver = { + .name = SSP_GYROSCOPE_NAME, + }, + .probe = ssp_gyro_probe, + .remove = ssp_gyro_remove, +}; + +module_platform_driver(ssp_gyro_driver); + +MODULE_AUTHOR("Karol Wrona <k.wrona@samsung.com>"); +MODULE_DESCRIPTION("Samsung sensorhub gyroscopes driver"); +MODULE_LICENSE("GPL"); -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v5 5/5] iio: common: ssp_sensors: Add sensorhub gyroscope sensor @ 2015-01-28 14:05 ` Karol Wrona 0 siblings, 0 replies; 19+ messages in thread From: Karol Wrona @ 2015-01-28 14:05 UTC (permalink / raw) To: Jonathan Cameron, linux-iio-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona, Karol Wrona This patch adds gyroscope iio driver which uses sensorhub as data provider. Signed-off-by: Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> Acked-by: Kyungmin Park <kyungmin.park-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> --- drivers/iio/gyro/Makefile | 2 + drivers/iio/gyro/ssp_gyro_sensor.c | 168 ++++++++++++++++++++++++++++++++++++ 2 files changed, 170 insertions(+) create mode 100644 drivers/iio/gyro/ssp_gyro_sensor.c diff --git a/drivers/iio/gyro/Makefile b/drivers/iio/gyro/Makefile index 36a3877..f46341b 100644 --- a/drivers/iio/gyro/Makefile +++ b/drivers/iio/gyro/Makefile @@ -16,6 +16,8 @@ itg3200-y := itg3200_core.o itg3200-$(CONFIG_IIO_BUFFER) += itg3200_buffer.o obj-$(CONFIG_ITG3200) += itg3200.o +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_gyro_sensor.o + obj-$(CONFIG_IIO_ST_GYRO_3AXIS) += st_gyro.o st_gyro-y := st_gyro_core.o st_gyro-$(CONFIG_IIO_BUFFER) += st_gyro_buffer.o diff --git a/drivers/iio/gyro/ssp_gyro_sensor.c b/drivers/iio/gyro/ssp_gyro_sensor.c new file mode 100644 index 0000000..0a8afdd --- /dev/null +++ b/drivers/iio/gyro/ssp_gyro_sensor.c @@ -0,0 +1,168 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/iio.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include "../common/ssp_sensors/ssp_iio_sensor.h" + +#define SSP_CHANNEL_COUNT 3 + +#define SSP_GYROSCOPE_NAME "ssp-gyroscope" +static const char ssp_gyro_name[] = SSP_GYROSCOPE_NAME; + +enum ssp_gyro_3d_channel { + SSP_CHANNEL_SCAN_INDEX_X, + SSP_CHANNEL_SCAN_INDEX_Y, + SSP_CHANNEL_SCAN_INDEX_Z, + SSP_CHANNEL_SCAN_INDEX_TIME, +}; + +static int ssp_gyro_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int *val, + int *val2, long mask) +{ + u32 t; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + t = ssp_get_sensor_delay(data, SSP_GYROSCOPE_SENSOR); + ssp_convert_to_freq(t, val, val2); + return IIO_VAL_INT_PLUS_MICRO; + default: + break; + } + + return -EINVAL; +} + +static int ssp_gyro_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, int val, + int val2, long mask) +{ + int ret; + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + ret = ssp_convert_to_time(val, val2); + ret = ssp_change_delay(data, SSP_GYROSCOPE_SENSOR, ret); + if (ret < 0) + dev_err(&indio_dev->dev, "gyro sensor enable fail\n"); + + return ret; + default: + break; + } + + return -EINVAL; +} + +static struct iio_info ssp_gyro_iio_info = { + .read_raw = &ssp_gyro_read_raw, + .write_raw = &ssp_gyro_write_raw, +}; + +static const unsigned long ssp_gyro_scan_mask[] = { 0x07, 0, }; + +static const struct iio_chan_spec ssp_gyro_channels[] = { + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_X, SSP_CHANNEL_SCAN_INDEX_X), + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_Y, SSP_CHANNEL_SCAN_INDEX_Y), + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_Z, SSP_CHANNEL_SCAN_INDEX_Z), + SSP_CHAN_TIMESTAMP(SSP_CHANNEL_SCAN_INDEX_TIME), +}; + +static int ssp_process_gyro_data(struct iio_dev *indio_dev, void *buf, + int64_t timestamp) +{ + return ssp_common_process_data(indio_dev, buf, SSP_GYROSCOPE_SIZE, + timestamp); +} + +static const struct iio_buffer_setup_ops ssp_gyro_buffer_ops = { + .postenable = &ssp_common_buffer_postenable, + .postdisable = &ssp_common_buffer_postdisable, +}; + +static int ssp_gyro_probe(struct platform_device *pdev) +{ + int ret; + struct iio_dev *indio_dev; + struct ssp_sensor_data *spd; + struct iio_buffer *buffer; + + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*spd)); + if (!indio_dev) + return -ENOMEM; + + spd = iio_priv(indio_dev); + + spd->process_data = ssp_process_gyro_data; + spd->type = SSP_GYROSCOPE_SENSOR; + + indio_dev->name = ssp_gyro_name; + indio_dev->dev.parent = &pdev->dev; + indio_dev->info = &ssp_gyro_iio_info; + indio_dev->modes = INDIO_BUFFER_SOFTWARE; + indio_dev->channels = ssp_gyro_channels; + indio_dev->num_channels = ARRAY_SIZE(ssp_gyro_channels); + indio_dev->available_scan_masks = ssp_gyro_scan_mask; + + buffer = devm_iio_kfifo_allocate(&pdev->dev); + if (!buffer) + return -ENOMEM; + + iio_device_attach_buffer(indio_dev, buffer); + + indio_dev->setup_ops = &ssp_gyro_buffer_ops; + + platform_set_drvdata(pdev, indio_dev); + + ret = iio_device_register(indio_dev); + if (ret < 0) + return ret; + + /* ssp registering should be done after all iio setup */ + ssp_register_consumer(indio_dev, SSP_GYROSCOPE_SENSOR); + + return 0; +} + +static int ssp_gyro_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + + iio_device_unregister(indio_dev); + + return 0; +} + +static struct platform_driver ssp_gyro_driver = { + .driver = { + .name = SSP_GYROSCOPE_NAME, + }, + .probe = ssp_gyro_probe, + .remove = ssp_gyro_remove, +}; + +module_platform_driver(ssp_gyro_driver); + +MODULE_AUTHOR("Karol Wrona <k.wrona-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>"); +MODULE_DESCRIPTION("Samsung sensorhub gyroscopes driver"); +MODULE_LICENSE("GPL"); -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v5 5/5] iio: common: ssp_sensors: Add sensorhub gyroscope sensor 2015-01-28 14:05 ` Karol Wrona (?) @ 2015-01-29 18:37 ` Jonathan Cameron -1 siblings, 0 replies; 19+ messages in thread From: Jonathan Cameron @ 2015-01-29 18:37 UTC (permalink / raw) To: Karol Wrona, linux-iio, devicetree, linux-kernel Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Bartlomiej Zolnierkiewicz, Kyungmin Park, Karol Wrona On 28/01/15 14:05, Karol Wrona wrote: > This patch adds gyroscope iio driver which uses sensorhub as data > provider. > > Signed-off-by: Karol Wrona <k.wrona@samsung.com> > Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Applied. A nice driver - glad to have it in the tree! Jonathan > --- > drivers/iio/gyro/Makefile | 2 + > drivers/iio/gyro/ssp_gyro_sensor.c | 168 ++++++++++++++++++++++++++++++++++++ > 2 files changed, 170 insertions(+) > create mode 100644 drivers/iio/gyro/ssp_gyro_sensor.c > > diff --git a/drivers/iio/gyro/Makefile b/drivers/iio/gyro/Makefile > index 36a3877..f46341b 100644 > --- a/drivers/iio/gyro/Makefile > +++ b/drivers/iio/gyro/Makefile > @@ -16,6 +16,8 @@ itg3200-y := itg3200_core.o > itg3200-$(CONFIG_IIO_BUFFER) += itg3200_buffer.o > obj-$(CONFIG_ITG3200) += itg3200.o > > +obj-$(CONFIG_IIO_SSP_SENSORS_COMMONS) += ssp_gyro_sensor.o > + > obj-$(CONFIG_IIO_ST_GYRO_3AXIS) += st_gyro.o > st_gyro-y := st_gyro_core.o > st_gyro-$(CONFIG_IIO_BUFFER) += st_gyro_buffer.o > diff --git a/drivers/iio/gyro/ssp_gyro_sensor.c b/drivers/iio/gyro/ssp_gyro_sensor.c > new file mode 100644 > index 0000000..0a8afdd > --- /dev/null > +++ b/drivers/iio/gyro/ssp_gyro_sensor.c > @@ -0,0 +1,168 @@ > +/* > + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <linux/iio/common/ssp_sensors.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/kfifo_buf.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/slab.h> > +#include "../common/ssp_sensors/ssp_iio_sensor.h" > + > +#define SSP_CHANNEL_COUNT 3 > + > +#define SSP_GYROSCOPE_NAME "ssp-gyroscope" > +static const char ssp_gyro_name[] = SSP_GYROSCOPE_NAME; > + > +enum ssp_gyro_3d_channel { > + SSP_CHANNEL_SCAN_INDEX_X, > + SSP_CHANNEL_SCAN_INDEX_Y, > + SSP_CHANNEL_SCAN_INDEX_Z, > + SSP_CHANNEL_SCAN_INDEX_TIME, > +}; > + > +static int ssp_gyro_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, int *val, > + int *val2, long mask) > +{ > + u32 t; > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + switch (mask) { > + case IIO_CHAN_INFO_SAMP_FREQ: > + t = ssp_get_sensor_delay(data, SSP_GYROSCOPE_SENSOR); > + ssp_convert_to_freq(t, val, val2); > + return IIO_VAL_INT_PLUS_MICRO; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int ssp_gyro_write_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, int val, > + int val2, long mask) > +{ > + int ret; > + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); > + > + switch (mask) { > + case IIO_CHAN_INFO_SAMP_FREQ: > + ret = ssp_convert_to_time(val, val2); > + ret = ssp_change_delay(data, SSP_GYROSCOPE_SENSOR, ret); > + if (ret < 0) > + dev_err(&indio_dev->dev, "gyro sensor enable fail\n"); > + > + return ret; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static struct iio_info ssp_gyro_iio_info = { > + .read_raw = &ssp_gyro_read_raw, > + .write_raw = &ssp_gyro_write_raw, > +}; > + > +static const unsigned long ssp_gyro_scan_mask[] = { 0x07, 0, }; > + > +static const struct iio_chan_spec ssp_gyro_channels[] = { > + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_X, SSP_CHANNEL_SCAN_INDEX_X), > + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_Y, SSP_CHANNEL_SCAN_INDEX_Y), > + SSP_CHANNEL_AG(IIO_ANGL_VEL, IIO_MOD_Z, SSP_CHANNEL_SCAN_INDEX_Z), > + SSP_CHAN_TIMESTAMP(SSP_CHANNEL_SCAN_INDEX_TIME), > +}; > + > +static int ssp_process_gyro_data(struct iio_dev *indio_dev, void *buf, > + int64_t timestamp) > +{ > + return ssp_common_process_data(indio_dev, buf, SSP_GYROSCOPE_SIZE, > + timestamp); > +} > + > +static const struct iio_buffer_setup_ops ssp_gyro_buffer_ops = { > + .postenable = &ssp_common_buffer_postenable, > + .postdisable = &ssp_common_buffer_postdisable, > +}; > + > +static int ssp_gyro_probe(struct platform_device *pdev) > +{ > + int ret; > + struct iio_dev *indio_dev; > + struct ssp_sensor_data *spd; > + struct iio_buffer *buffer; > + > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*spd)); > + if (!indio_dev) > + return -ENOMEM; > + > + spd = iio_priv(indio_dev); > + > + spd->process_data = ssp_process_gyro_data; > + spd->type = SSP_GYROSCOPE_SENSOR; > + > + indio_dev->name = ssp_gyro_name; > + indio_dev->dev.parent = &pdev->dev; > + indio_dev->info = &ssp_gyro_iio_info; > + indio_dev->modes = INDIO_BUFFER_SOFTWARE; > + indio_dev->channels = ssp_gyro_channels; > + indio_dev->num_channels = ARRAY_SIZE(ssp_gyro_channels); > + indio_dev->available_scan_masks = ssp_gyro_scan_mask; > + > + buffer = devm_iio_kfifo_allocate(&pdev->dev); > + if (!buffer) > + return -ENOMEM; > + > + iio_device_attach_buffer(indio_dev, buffer); > + > + indio_dev->setup_ops = &ssp_gyro_buffer_ops; > + > + platform_set_drvdata(pdev, indio_dev); > + > + ret = iio_device_register(indio_dev); > + if (ret < 0) > + return ret; > + > + /* ssp registering should be done after all iio setup */ > + ssp_register_consumer(indio_dev, SSP_GYROSCOPE_SENSOR); > + > + return 0; > +} > + > +static int ssp_gyro_remove(struct platform_device *pdev) > +{ > + struct iio_dev *indio_dev = platform_get_drvdata(pdev); > + > + iio_device_unregister(indio_dev); > + > + return 0; > +} > + > +static struct platform_driver ssp_gyro_driver = { > + .driver = { > + .name = SSP_GYROSCOPE_NAME, > + }, > + .probe = ssp_gyro_probe, > + .remove = ssp_gyro_remove, > +}; > + > +module_platform_driver(ssp_gyro_driver); > + > +MODULE_AUTHOR("Karol Wrona <k.wrona@samsung.com>"); > +MODULE_DESCRIPTION("Samsung sensorhub gyroscopes driver"); > +MODULE_LICENSE("GPL"); > ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2015-01-29 18:53 UTC | newest] Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2015-01-28 14:05 [PATCH v5 0/5] iio: Add sensorhub driver Karol Wrona 2015-01-28 14:05 ` [PATCH v5 1/5] iio: common: ssp_sensors: " Karol Wrona 2015-01-29 18:35 ` Jonathan Cameron 2015-01-29 18:35 ` Jonathan Cameron 2015-01-29 18:46 ` Karol Wrona 2015-01-29 18:53 ` Jonathan Cameron 2015-01-29 18:53 ` Jonathan Cameron 2015-01-28 14:05 ` [PATCH v5 2/5] iio: sensorhub: Add sensorhub bindings Karol Wrona 2015-01-28 14:05 ` Karol Wrona 2015-01-29 18:36 ` Jonathan Cameron 2015-01-28 14:05 ` [PATCH v5 3/5] iio: common: ssp_sensors: Add sensorhub iio commons Karol Wrona 2015-01-29 18:36 ` Jonathan Cameron 2015-01-29 18:36 ` Jonathan Cameron 2015-01-28 14:05 ` [PATCH v5 4/5] iio: common: ssp_sensors: Add sensorhub accelerometer sensor Karol Wrona 2015-01-28 14:05 ` Karol Wrona 2015-01-29 18:37 ` Jonathan Cameron 2015-01-28 14:05 ` [PATCH v5 5/5] iio: common: ssp_sensors: Add sensorhub gyroscope sensor Karol Wrona 2015-01-28 14:05 ` Karol Wrona 2015-01-29 18:37 ` Jonathan Cameron
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.