All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH 00/10] ARM: mvebu: add basic support for Armada 39x
@ 2015-02-06 15:57 ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
	Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linux-gpio-u79uwXL29TY76Z2rM5mHXA, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

Hello,

This set of patches add basic support for a new family of Marvell EBU
processors: the Armada 39x. They are based on Cortex-A9 (like Armada
375 and 38x) and the most important new feature is probably the
addition of 10 GbE support.

See http://www.marvell.com/embedded-processors/armada-39x/ for a basic
introduction.

Note that this web page talks about an Armada 395 and Armada 398, but
so far the technical documentation we have been given access to only
describes Armada 390 and Armada 398, so this series supports only
Armada 390 and Armada 398 so far. Support for Armada 395 might be
added in the future, once we get access to the appropriate technical
details.

Besides this, this series should be relatively straightforward:

 * Addition or update of various Device Tree binding documents

 * Addition of clock support for Armada 39x

 * Addition of pinctrl support for Armada 39x

 * Core support and Device Tree for Armada 39x, with one Armada 398
   Development Board supported

For now, the support is limited to a small subset of devices, we will
enable more and more hardware blocks in the near future.

This branch is based on mvebu/for-next, and is obviously 3.21
material. Such an early posting is done to gather early review and
feedback. I'll repost an updated series that takes into account the
initial feedback once 3.20-rc1 lands.

Thanks,

Thomas Petazzoni

Thomas Petazzoni (10):
  devicetree: bindings: add DT binding for the Marvell Armada 39x SoC
    family
  devicetree: bindings: update DT bindings for Marvell EBU clock support
  devicetree: bindings: add Device Tree bindings for Armada 39x
    pin-muxing controller
  devicetree: bindings: add new SMP enable method for Marvell Armada 39x
  clk: mvebu: extend common code to allow an optional refclk
  clk: mvebu: add Marvell Armada 39x driver
  pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
  ARM: mvebu: add core support for Armada 39x
  ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  Documentation: arm: update supported Marvell EBU processors

 Documentation/arm/Marvell/README                   |   5 +
 .../devicetree/bindings/arm/armada-39x.txt         |  20 +
 Documentation/devicetree/bindings/arm/cpus.txt     |   1 +
 .../devicetree/bindings/clock/mvebu-core-clock.txt |   9 +
 .../bindings/clock/mvebu-gated-clock.txt           |  15 +-
 .../pinctrl/marvell,armada-39x-pinctrl.txt         |  78 ++++
 arch/arm/boot/dts/Makefile                         |   2 +
 arch/arm/boot/dts/armada-390.dtsi                  |  57 +++
 arch/arm/boot/dts/armada-398-db.dts                | 116 ++++++
 arch/arm/boot/dts/armada-398.dtsi                  |  60 +++
 arch/arm/boot/dts/armada-39x.dtsi                  | 372 ++++++++++++++++++
 arch/arm/mach-mvebu/Kconfig                        |  14 +
 arch/arm/mach-mvebu/board-v7.c                     |  14 +
 arch/arm/mach-mvebu/platsmp-a9.c                   |   2 +
 drivers/clk/mvebu/Kconfig                          |   4 +
 drivers/clk/mvebu/Makefile                         |   1 +
 drivers/clk/mvebu/armada-39x.c                     | 156 ++++++++
 drivers/clk/mvebu/common.c                         |  17 +
 drivers/clk/mvebu/common.h                         |   1 +
 drivers/pinctrl/mvebu/Kconfig                      |   4 +
 drivers/pinctrl/mvebu/Makefile                     |   1 +
 drivers/pinctrl/mvebu/pinctrl-armada-39x.c         | 432 +++++++++++++++++++++
 22 files changed, 1380 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/arm/armada-39x.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
 create mode 100644 arch/arm/boot/dts/armada-390.dtsi
 create mode 100644 arch/arm/boot/dts/armada-398-db.dts
 create mode 100644 arch/arm/boot/dts/armada-398.dtsi
 create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
 create mode 100644 drivers/clk/mvebu/armada-39x.c
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-39x.c

-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 00/10] ARM: mvebu: add basic support for Armada 39x
@ 2015-02-06 15:57 ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

Hello,

This set of patches add basic support for a new family of Marvell EBU
processors: the Armada 39x. They are based on Cortex-A9 (like Armada
375 and 38x) and the most important new feature is probably the
addition of 10 GbE support.

See http://www.marvell.com/embedded-processors/armada-39x/ for a basic
introduction.

Note that this web page talks about an Armada 395 and Armada 398, but
so far the technical documentation we have been given access to only
describes Armada 390 and Armada 398, so this series supports only
Armada 390 and Armada 398 so far. Support for Armada 395 might be
added in the future, once we get access to the appropriate technical
details.

Besides this, this series should be relatively straightforward:

 * Addition or update of various Device Tree binding documents

 * Addition of clock support for Armada 39x

 * Addition of pinctrl support for Armada 39x

 * Core support and Device Tree for Armada 39x, with one Armada 398
   Development Board supported

For now, the support is limited to a small subset of devices, we will
enable more and more hardware blocks in the near future.

This branch is based on mvebu/for-next, and is obviously 3.21
material. Such an early posting is done to gather early review and
feedback. I'll repost an updated series that takes into account the
initial feedback once 3.20-rc1 lands.

Thanks,

Thomas Petazzoni

Thomas Petazzoni (10):
  devicetree: bindings: add DT binding for the Marvell Armada 39x SoC
    family
  devicetree: bindings: update DT bindings for Marvell EBU clock support
  devicetree: bindings: add Device Tree bindings for Armada 39x
    pin-muxing controller
  devicetree: bindings: add new SMP enable method for Marvell Armada 39x
  clk: mvebu: extend common code to allow an optional refclk
  clk: mvebu: add Marvell Armada 39x driver
  pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
  ARM: mvebu: add core support for Armada 39x
  ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  Documentation: arm: update supported Marvell EBU processors

 Documentation/arm/Marvell/README                   |   5 +
 .../devicetree/bindings/arm/armada-39x.txt         |  20 +
 Documentation/devicetree/bindings/arm/cpus.txt     |   1 +
 .../devicetree/bindings/clock/mvebu-core-clock.txt |   9 +
 .../bindings/clock/mvebu-gated-clock.txt           |  15 +-
 .../pinctrl/marvell,armada-39x-pinctrl.txt         |  78 ++++
 arch/arm/boot/dts/Makefile                         |   2 +
 arch/arm/boot/dts/armada-390.dtsi                  |  57 +++
 arch/arm/boot/dts/armada-398-db.dts                | 116 ++++++
 arch/arm/boot/dts/armada-398.dtsi                  |  60 +++
 arch/arm/boot/dts/armada-39x.dtsi                  | 372 ++++++++++++++++++
 arch/arm/mach-mvebu/Kconfig                        |  14 +
 arch/arm/mach-mvebu/board-v7.c                     |  14 +
 arch/arm/mach-mvebu/platsmp-a9.c                   |   2 +
 drivers/clk/mvebu/Kconfig                          |   4 +
 drivers/clk/mvebu/Makefile                         |   1 +
 drivers/clk/mvebu/armada-39x.c                     | 156 ++++++++
 drivers/clk/mvebu/common.c                         |  17 +
 drivers/clk/mvebu/common.h                         |   1 +
 drivers/pinctrl/mvebu/Kconfig                      |   4 +
 drivers/pinctrl/mvebu/Makefile                     |   1 +
 drivers/pinctrl/mvebu/pinctrl-armada-39x.c         | 432 +++++++++++++++++++++
 22 files changed, 1380 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/arm/armada-39x.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
 create mode 100644 arch/arm/boot/dts/armada-390.dtsi
 create mode 100644 arch/arm/boot/dts/armada-398-db.dts
 create mode 100644 arch/arm/boot/dts/armada-398.dtsi
 create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
 create mode 100644 drivers/clk/mvebu/armada-39x.c
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-39x.c

-- 
2.1.0

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 01/10] devicetree: bindings: add DT binding for the Marvell Armada 39x SoC family
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

The Marvell Armada 39x is a family of two SoCs: the Armada 390 and the
Armada 398, with a slightly different number of interfaces. This
commit introduces the Device Tree binding that documents the top-level
compatible strings for Armada 39x based platforms.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 Documentation/devicetree/bindings/arm/armada-39x.txt | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/armada-39x.txt

diff --git a/Documentation/devicetree/bindings/arm/armada-39x.txt b/Documentation/devicetree/bindings/arm/armada-39x.txt
new file mode 100644
index 0000000..53d4ff9
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/armada-39x.txt
@@ -0,0 +1,20 @@
+Marvell Armada 39x Platforms Device Tree Bindings
+-------------------------------------------------
+
+Boards with a SoC of the Marvell Armada 39x family shall have the
+following property:
+
+Required root node property:
+
+ - compatible: must contain "marvell,armada390"
+
+In addition, boards using the Marvell Armada 398 SoC shall have the
+following property before the previous one:
+
+Required root node property:
+
+compatible: must contain "marvell,armada398"
+
+Example:
+
+compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 01/10] devicetree: bindings: add DT binding for the Marvell Armada 39x SoC family
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

The Marvell Armada 39x is a family of two SoCs: the Armada 390 and the
Armada 398, with a slightly different number of interfaces. This
commit introduces the Device Tree binding that documents the top-level
compatible strings for Armada 39x based platforms.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 Documentation/devicetree/bindings/arm/armada-39x.txt | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/armada-39x.txt

diff --git a/Documentation/devicetree/bindings/arm/armada-39x.txt b/Documentation/devicetree/bindings/arm/armada-39x.txt
new file mode 100644
index 0000000..53d4ff9
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/armada-39x.txt
@@ -0,0 +1,20 @@
+Marvell Armada 39x Platforms Device Tree Bindings
+-------------------------------------------------
+
+Boards with a SoC of the Marvell Armada 39x family shall have the
+following property:
+
+Required root node property:
+
+ - compatible: must contain "marvell,armada390"
+
+In addition, boards using the Marvell Armada 398 SoC shall have the
+following property before the previous one:
+
+Required root node property:
+
+compatible: must contain "marvell,armada398"
+
+Example:
+
+compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 02/10] devicetree: bindings: update DT bindings for Marvell EBU clock support
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

With the introduction of the Marvell Armada 39x SoC, the DT bindings
for Marvell EBU clocks need to be extended. This commit include the
corresponding update to the Device Tree bindings documentation.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 .../devicetree/bindings/clock/mvebu-core-clock.txt        |  9 +++++++++
 .../devicetree/bindings/clock/mvebu-gated-clock.txt       | 15 ++++++++++++++-
 2 files changed, 23 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
index dc5ea5b..670c2af 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
@@ -23,6 +23,14 @@ The following is a list of provided IDs and clock names on Armada 380/385:
  2 = l2clk   (L2 Cache clock)
  3 = ddrclk  (DDR clock)
 
+The following is a list of provided IDs and clock names on Armada 39x:
+ 0 = tclk    (Internal Bus clock)
+ 1 = cpuclk  (CPU clock)
+ 2 = nbclk   (Coherent Fabric clock)
+ 3 = hclk    (SDRAM Controller Internal Clock)
+ 4 = dclk    (SDRAM Interface Clock)
+ 5 = refclk  (Reference Clock)
+
 The following is a list of provided IDs and clock names on Kirkwood and Dove:
  0 = tclk   (Internal Bus clock)
  1 = cpuclk (CPU0 clock)
@@ -39,6 +47,7 @@ Required properties:
 	"marvell,armada-370-core-clock" - For Armada 370 SoC core clocks
 	"marvell,armada-375-core-clock" - For Armada 375 SoC core clocks
 	"marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks
+	"marvell,armada-390-core-clock" - For Armada 39x SoC core clocks
 	"marvell,armada-xp-core-clock" - For Armada XP SoC core clocks
 	"marvell,dove-core-clock" - for Dove SoC core clocks
 	"marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180)
diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt
index 76477be..31c7c0c 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt
@@ -1,6 +1,6 @@
 * Gated Clock bindings for Marvell EBU SoCs
 
-Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some
+Marvell Armada 370/375/380/385/39x/XP, Dove and Kirkwood allow some
 peripheral clocks to be gated to save some power. The clock consumer
 should specify the desired clock by having the clock ID in its
 "clocks" phandle cell. The clock ID is directly mapped to the
@@ -77,6 +77,18 @@ ID	Clock		Peripheral
 28	xor1		XOR 1
 30	sata1		SATA 1
 
+The following is a list of provided IDs for Armada 39x:
+ID	Clock		Peripheral
+-----------------------------------
+5	pex1		PCIe 1
+6	pex2		PCIe 2
+7	pex3		PCIe 3
+8	pex0		PCIe 0
+9	usb3h0		USB3 Host 0
+17	sdio		SDIO
+22	xor0		XOR 0
+28	xor1		XOR 1
+
 The following is a list of provided IDs for Armada XP:
 ID	Clock	Peripheral
 -----------------------------------
@@ -152,6 +164,7 @@ Required properties:
 	"marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating
 	"marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating
 	"marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating
+	"marvell,armada-390-gating-clock" - for Armada 39x SoC clock gating
 	"marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating
 	"marvell,dove-gating-clock" - for Dove SoC clock gating
 	"marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 02/10] devicetree: bindings: update DT bindings for Marvell EBU clock support
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

With the introduction of the Marvell Armada 39x SoC, the DT bindings
for Marvell EBU clocks need to be extended. This commit include the
corresponding update to the Device Tree bindings documentation.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 .../devicetree/bindings/clock/mvebu-core-clock.txt        |  9 +++++++++
 .../devicetree/bindings/clock/mvebu-gated-clock.txt       | 15 ++++++++++++++-
 2 files changed, 23 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
index dc5ea5b..670c2af 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
@@ -23,6 +23,14 @@ The following is a list of provided IDs and clock names on Armada 380/385:
  2 = l2clk   (L2 Cache clock)
  3 = ddrclk  (DDR clock)
 
+The following is a list of provided IDs and clock names on Armada 39x:
+ 0 = tclk    (Internal Bus clock)
+ 1 = cpuclk  (CPU clock)
+ 2 = nbclk   (Coherent Fabric clock)
+ 3 = hclk    (SDRAM Controller Internal Clock)
+ 4 = dclk    (SDRAM Interface Clock)
+ 5 = refclk  (Reference Clock)
+
 The following is a list of provided IDs and clock names on Kirkwood and Dove:
  0 = tclk   (Internal Bus clock)
  1 = cpuclk (CPU0 clock)
@@ -39,6 +47,7 @@ Required properties:
 	"marvell,armada-370-core-clock" - For Armada 370 SoC core clocks
 	"marvell,armada-375-core-clock" - For Armada 375 SoC core clocks
 	"marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks
+	"marvell,armada-390-core-clock" - For Armada 39x SoC core clocks
 	"marvell,armada-xp-core-clock" - For Armada XP SoC core clocks
 	"marvell,dove-core-clock" - for Dove SoC core clocks
 	"marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180)
diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt
index 76477be..31c7c0c 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt
@@ -1,6 +1,6 @@
 * Gated Clock bindings for Marvell EBU SoCs
 
-Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some
+Marvell Armada 370/375/380/385/39x/XP, Dove and Kirkwood allow some
 peripheral clocks to be gated to save some power. The clock consumer
 should specify the desired clock by having the clock ID in its
 "clocks" phandle cell. The clock ID is directly mapped to the
@@ -77,6 +77,18 @@ ID	Clock		Peripheral
 28	xor1		XOR 1
 30	sata1		SATA 1
 
+The following is a list of provided IDs for Armada 39x:
+ID	Clock		Peripheral
+-----------------------------------
+5	pex1		PCIe 1
+6	pex2		PCIe 2
+7	pex3		PCIe 3
+8	pex0		PCIe 0
+9	usb3h0		USB3 Host 0
+17	sdio		SDIO
+22	xor0		XOR 0
+28	xor1		XOR 1
+
 The following is a list of provided IDs for Armada XP:
 ID	Clock	Peripheral
 -----------------------------------
@@ -152,6 +164,7 @@ Required properties:
 	"marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating
 	"marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating
 	"marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating
+	"marvell,armada-390-gating-clock" - for Armada 39x SoC clock gating
 	"marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating
 	"marvell,dove-gating-clock" - for Dove SoC clock gating
 	"marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

This commit adds the Device Tree binding documentation to describe the
pin-muxing controller of the Marvell Armada 39x processors. Two
variants are supported for the moment: the 88F6920 (Armada 390) and
88F6928 (Armada 398).

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 .../pinctrl/marvell,armada-39x-pinctrl.txt         | 78 ++++++++++++++++++++++
 1 file changed, 78 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
new file mode 100644
index 0000000..5b1a9dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
@@ -0,0 +1,78 @@
+* Marvell Armada 39x SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl"
+  depending on the specific variant of the SoC being used.
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name    pins    functions
+================================================================================
+mpp0	0	gpio, ua0(rxd)
+mpp1	1	gpio, ua0(txd)
+mpp2	2	gpio, i2c0(sck)
+mpp3	3	gpio, i2c0(sda)
+mpp4	4	gpio, ua1(txd), ua0(rts), smi(mdc)
+mpp5	5	gpio, ua1(rxd), ua0(cts), smi(mdio)
+mpp6	6	gpio, dev(cs3), xsmi(mdio)
+mpp7	7	gpio, dev(ad9), xsmi(mdc)
+mpp8	8	gpio, dev(ad10), ptp(trig)
+mpp9	9	gpio, dev(ad11), ptp(clk)
+mpp10	10	gpio, dev(ad12), ptp(event)
+mpp11	11	gpio, dev(ad13), led(clk)
+mpp12	12	gpio, pcie0(rstout), dev(ad14), led(stb)
+mpp13	13	gpio, dev(ad15), led(data)
+mpp14	14	gpio, m(vtt), dev(wen1), ua1(txd)
+mpp15	15	gpio, pcie0(rstout), spi0(mosi), i2c1(sck)
+mpp16	16	gpio, m(decc), spi0(miso), i2c1(sda)
+mpp17	17	gpio, ua1(rxd), spi0(sck), smi(mdio)
+mpp18	18	gpio, ua1(txd), spi0(cs0), i2c2(sck)
+mpp19	19	gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda)
+mpp20	20	gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc)
+mpp21	21	gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0)
+mpp22	22	gpio, spi0(mosi), dev(ad0)
+mpp23	23	gpio, spi0(sck), dev(ad2)
+mpp24	24	gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
+mpp25	25	gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0)
+mpp26	26	gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1)
+mpp27	27	gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout)
+mpp28	28	gpio, sd(clk), dev(ad5), ge(txd0)
+mpp29	29	gpio, dev(ale0), ge(txd1)
+mpp30	30	gpio, dev(oen), ge(txd2)
+mpp31	31	gpio, dev(ale1), ge(txd3)
+mpp32	32	gpio, dev(wen0), ge(txctl)
+mpp33	33	gpio, m(decc), dev(ad3)
+mpp34	34	gpio, dev(ad1)
+mpp35	35	gpio, ref(clk), dev(a1)
+mpp36	36	gpio, dev(a0)
+mpp37	37	gpio, sd(d3), dev(ad8), ge(rxclk)
+mpp38	38	gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1)
+mpp39	39	gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2)
+mpp40	40	gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3)
+mpp41	41	gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl)
+mpp42	42	gpio, ua1(txd), ua0(rts), dev(ad7)
+mpp43	43	gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1)
+mpp44	44	gpio, sata0(present) [1], sata1(present) [1], led(clk)
+mpp45	45	gpio, ref(clk), pcie0(rstout), ua1(rxd)
+mpp46	46	gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb)
+mpp47	47	gpio, sata0(present) [1], sata1(present) [1], led(data)
+mpp48	48	gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd)
+mpp49	49	gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd)
+mpp50	50	gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd)
+mpp51	51	gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd)
+mpp52	52	gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck)
+mpp53	53	gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda)
+mpp54	54	gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd)
+mpp55	55	gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd)
+mpp56	56	gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd)
+mpp57	57	gpio, spi1(sck), sd(clk), ua1(txd)
+mpp58	58	gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
+mpp59	59	gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2)
+
+[1]: only available on 88F6928
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

This commit adds the Device Tree binding documentation to describe the
pin-muxing controller of the Marvell Armada 39x processors. Two
variants are supported for the moment: the 88F6920 (Armada 390) and
88F6928 (Armada 398).

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 .../pinctrl/marvell,armada-39x-pinctrl.txt         | 78 ++++++++++++++++++++++
 1 file changed, 78 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
new file mode 100644
index 0000000..5b1a9dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
@@ -0,0 +1,78 @@
+* Marvell Armada 39x SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl"
+  depending on the specific variant of the SoC being used.
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name    pins    functions
+================================================================================
+mpp0	0	gpio, ua0(rxd)
+mpp1	1	gpio, ua0(txd)
+mpp2	2	gpio, i2c0(sck)
+mpp3	3	gpio, i2c0(sda)
+mpp4	4	gpio, ua1(txd), ua0(rts), smi(mdc)
+mpp5	5	gpio, ua1(rxd), ua0(cts), smi(mdio)
+mpp6	6	gpio, dev(cs3), xsmi(mdio)
+mpp7	7	gpio, dev(ad9), xsmi(mdc)
+mpp8	8	gpio, dev(ad10), ptp(trig)
+mpp9	9	gpio, dev(ad11), ptp(clk)
+mpp10	10	gpio, dev(ad12), ptp(event)
+mpp11	11	gpio, dev(ad13), led(clk)
+mpp12	12	gpio, pcie0(rstout), dev(ad14), led(stb)
+mpp13	13	gpio, dev(ad15), led(data)
+mpp14	14	gpio, m(vtt), dev(wen1), ua1(txd)
+mpp15	15	gpio, pcie0(rstout), spi0(mosi), i2c1(sck)
+mpp16	16	gpio, m(decc), spi0(miso), i2c1(sda)
+mpp17	17	gpio, ua1(rxd), spi0(sck), smi(mdio)
+mpp18	18	gpio, ua1(txd), spi0(cs0), i2c2(sck)
+mpp19	19	gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda)
+mpp20	20	gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc)
+mpp21	21	gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0)
+mpp22	22	gpio, spi0(mosi), dev(ad0)
+mpp23	23	gpio, spi0(sck), dev(ad2)
+mpp24	24	gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
+mpp25	25	gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0)
+mpp26	26	gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1)
+mpp27	27	gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout)
+mpp28	28	gpio, sd(clk), dev(ad5), ge(txd0)
+mpp29	29	gpio, dev(ale0), ge(txd1)
+mpp30	30	gpio, dev(oen), ge(txd2)
+mpp31	31	gpio, dev(ale1), ge(txd3)
+mpp32	32	gpio, dev(wen0), ge(txctl)
+mpp33	33	gpio, m(decc), dev(ad3)
+mpp34	34	gpio, dev(ad1)
+mpp35	35	gpio, ref(clk), dev(a1)
+mpp36	36	gpio, dev(a0)
+mpp37	37	gpio, sd(d3), dev(ad8), ge(rxclk)
+mpp38	38	gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1)
+mpp39	39	gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2)
+mpp40	40	gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3)
+mpp41	41	gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl)
+mpp42	42	gpio, ua1(txd), ua0(rts), dev(ad7)
+mpp43	43	gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1)
+mpp44	44	gpio, sata0(present) [1], sata1(present) [1], led(clk)
+mpp45	45	gpio, ref(clk), pcie0(rstout), ua1(rxd)
+mpp46	46	gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb)
+mpp47	47	gpio, sata0(present) [1], sata1(present) [1], led(data)
+mpp48	48	gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd)
+mpp49	49	gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd)
+mpp50	50	gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd)
+mpp51	51	gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd)
+mpp52	52	gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck)
+mpp53	53	gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda)
+mpp54	54	gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd)
+mpp55	55	gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd)
+mpp56	56	gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd)
+mpp57	57	gpio, spi1(sck), sd(clk), ua1(txd)
+mpp58	58	gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
+mpp59	59	gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2)
+
+[1]: only available on 88F6928
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 04/10] devicetree: bindings: add new SMP enable method for Marvell Armada 39x
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57     ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
	Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linux-gpio-u79uwXL29TY76Z2rM5mHXA, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

This commit updates the ARM CPUs Device Tree binding to document a new
enable method of Marvell Armada 39x processors.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 Documentation/devicetree/bindings/arm/cpus.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index b2aacbe..eb13d2e 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -191,6 +191,7 @@ nodes to be present and contain the properties described below.
 			    "brcm,brahma-b15"
 			    "marvell,armada-375-smp"
 			    "marvell,armada-380-smp"
+			    "marvell,armada-390-smp"
 			    "marvell,armada-xp-smp"
 			    "qcom,gcc-msm8660"
 			    "qcom,kpss-acc-v1"
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 04/10] devicetree: bindings: add new SMP enable method for Marvell Armada 39x
@ 2015-02-06 15:57     ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

This commit updates the ARM CPUs Device Tree binding to document a new
enable method of Marvell Armada 39x processors.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 Documentation/devicetree/bindings/arm/cpus.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index b2aacbe..eb13d2e 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -191,6 +191,7 @@ nodes to be present and contain the properties described below.
 			    "brcm,brahma-b15"
 			    "marvell,armada-375-smp"
 			    "marvell,armada-380-smp"
+			    "marvell,armada-390-smp"
 			    "marvell,armada-xp-smp"
 			    "qcom,gcc-msm8660"
 			    "qcom,kpss-acc-v1"
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 05/10] clk: mvebu: extend common code to allow an optional refclk
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

The Armada 39x, contrary to its predecessor, has a configurable
reference clock frequency, of either 25 Mhz, or 40 Mhz. For the
previous SoCs, it was fixed to 25 Mhz and described directly as such
in the Device Tree.

For Armada 39x, we need to read certain registers to know whether the
frequency is 25 or 40 Mhz. Therefore, this commit extends the common
mvebu clock code to allow the SoC-specific code to say it wants to
register a reference clock, by giving a non-NULL ->get_refclk_freq()
function pointer in its coreclk_soc_desc structure.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 drivers/clk/mvebu/common.c | 17 +++++++++++++++++
 drivers/clk/mvebu/common.h |  1 +
 2 files changed, 18 insertions(+)

diff --git a/drivers/clk/mvebu/common.c b/drivers/clk/mvebu/common.c
index 0d4d121..15b370f 100644
--- a/drivers/clk/mvebu/common.c
+++ b/drivers/clk/mvebu/common.c
@@ -121,6 +121,11 @@ void __init mvebu_coreclk_setup(struct device_node *np,
 
 	/* Allocate struct for TCLK, cpu clk, and core ratio clocks */
 	clk_data.clk_num = 2 + desc->num_ratios;
+
+	/* One more clock for the optional refclk */
+	if (desc->get_refclk_freq)
+		clk_data.clk_num += 1;
+
 	clk_data.clks = kzalloc(clk_data.clk_num * sizeof(struct clk *),
 				GFP_KERNEL);
 	if (WARN_ON(!clk_data.clks)) {
@@ -162,6 +167,18 @@ void __init mvebu_coreclk_setup(struct device_node *np,
 		WARN_ON(IS_ERR(clk_data.clks[2+n]));
 	};
 
+	/* Register optional refclk */
+	if (desc->get_refclk_freq) {
+		const char *name = "refclk";
+		of_property_read_string_index(np, "clock-output-names",
+					      2 + desc->num_ratios, &name);
+		rate = desc->get_refclk_freq(base);
+		clk_data.clks[2 + desc->num_ratios] =
+			clk_register_fixed_rate(NULL, name, NULL,
+						CLK_IS_ROOT, rate);
+		WARN_ON(IS_ERR(clk_data.clks[2 + desc->num_ratios]));
+	}
+
 	/* SAR register isn't needed anymore */
 	iounmap(base);
 
diff --git a/drivers/clk/mvebu/common.h b/drivers/clk/mvebu/common.h
index 783b563..f0de6c8 100644
--- a/drivers/clk/mvebu/common.h
+++ b/drivers/clk/mvebu/common.h
@@ -30,6 +30,7 @@ struct coreclk_soc_desc {
 	u32 (*get_tclk_freq)(void __iomem *sar);
 	u32 (*get_cpu_freq)(void __iomem *sar);
 	void (*get_clk_ratio)(void __iomem *sar, int id, int *mult, int *div);
+	u32 (*get_refclk_freq)(void __iomem *sar);
 	bool (*is_sscg_enabled)(void __iomem *sar);
 	u32 (*fix_sscg_deviation)(u32 system_clk);
 	const struct coreclk_ratio *ratios;
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 05/10] clk: mvebu: extend common code to allow an optional refclk
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

The Armada 39x, contrary to its predecessor, has a configurable
reference clock frequency, of either 25 Mhz, or 40 Mhz. For the
previous SoCs, it was fixed to 25 Mhz and described directly as such
in the Device Tree.

For Armada 39x, we need to read certain registers to know whether the
frequency is 25 or 40 Mhz. Therefore, this commit extends the common
mvebu clock code to allow the SoC-specific code to say it wants to
register a reference clock, by giving a non-NULL ->get_refclk_freq()
function pointer in its coreclk_soc_desc structure.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 drivers/clk/mvebu/common.c | 17 +++++++++++++++++
 drivers/clk/mvebu/common.h |  1 +
 2 files changed, 18 insertions(+)

diff --git a/drivers/clk/mvebu/common.c b/drivers/clk/mvebu/common.c
index 0d4d121..15b370f 100644
--- a/drivers/clk/mvebu/common.c
+++ b/drivers/clk/mvebu/common.c
@@ -121,6 +121,11 @@ void __init mvebu_coreclk_setup(struct device_node *np,
 
 	/* Allocate struct for TCLK, cpu clk, and core ratio clocks */
 	clk_data.clk_num = 2 + desc->num_ratios;
+
+	/* One more clock for the optional refclk */
+	if (desc->get_refclk_freq)
+		clk_data.clk_num += 1;
+
 	clk_data.clks = kzalloc(clk_data.clk_num * sizeof(struct clk *),
 				GFP_KERNEL);
 	if (WARN_ON(!clk_data.clks)) {
@@ -162,6 +167,18 @@ void __init mvebu_coreclk_setup(struct device_node *np,
 		WARN_ON(IS_ERR(clk_data.clks[2+n]));
 	};
 
+	/* Register optional refclk */
+	if (desc->get_refclk_freq) {
+		const char *name = "refclk";
+		of_property_read_string_index(np, "clock-output-names",
+					      2 + desc->num_ratios, &name);
+		rate = desc->get_refclk_freq(base);
+		clk_data.clks[2 + desc->num_ratios] =
+			clk_register_fixed_rate(NULL, name, NULL,
+						CLK_IS_ROOT, rate);
+		WARN_ON(IS_ERR(clk_data.clks[2 + desc->num_ratios]));
+	}
+
 	/* SAR register isn't needed anymore */
 	iounmap(base);
 
diff --git a/drivers/clk/mvebu/common.h b/drivers/clk/mvebu/common.h
index 783b563..f0de6c8 100644
--- a/drivers/clk/mvebu/common.h
+++ b/drivers/clk/mvebu/common.h
@@ -30,6 +30,7 @@ struct coreclk_soc_desc {
 	u32 (*get_tclk_freq)(void __iomem *sar);
 	u32 (*get_cpu_freq)(void __iomem *sar);
 	void (*get_clk_ratio)(void __iomem *sar, int id, int *mult, int *div);
+	u32 (*get_refclk_freq)(void __iomem *sar);
 	bool (*is_sscg_enabled)(void __iomem *sar);
 	u32 (*fix_sscg_deviation)(u32 system_clk);
 	const struct coreclk_ratio *ratios;
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 06/10] clk: mvebu: add Marvell Armada 39x driver
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

This commit adds a new clock driver for the Marvell Armada 39x family
of processors. This driver is fairly similar to the ones already used
on other Marvell EBU processors, with the following main differences:

 * Different set of ratios
 * Different set of core clocks
 * Configurable reference clock in frequency

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 drivers/clk/mvebu/Kconfig      |   4 ++
 drivers/clk/mvebu/Makefile     |   1 +
 drivers/clk/mvebu/armada-39x.c | 156 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 161 insertions(+)
 create mode 100644 drivers/clk/mvebu/armada-39x.c

diff --git a/drivers/clk/mvebu/Kconfig b/drivers/clk/mvebu/Kconfig
index 3b34dba..2769625 100644
--- a/drivers/clk/mvebu/Kconfig
+++ b/drivers/clk/mvebu/Kconfig
@@ -21,6 +21,10 @@ config ARMADA_38X_CLK
 	bool
 	select MVEBU_CLK_COMMON
 
+config ARMADA_39X_CLK
+	bool
+	select MVEBU_CLK_COMMON
+
 config ARMADA_XP_CLK
 	bool
 	select MVEBU_CLK_COMMON
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
index a9a56fc..645ac7e 100644
--- a/drivers/clk/mvebu/Makefile
+++ b/drivers/clk/mvebu/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_MVEBU_CLK_COREDIV)	+= clk-corediv.o
 obj-$(CONFIG_ARMADA_370_CLK)	+= armada-370.o
 obj-$(CONFIG_ARMADA_375_CLK)	+= armada-375.o
 obj-$(CONFIG_ARMADA_38X_CLK)	+= armada-38x.o
+obj-$(CONFIG_ARMADA_39X_CLK)	+= armada-39x.o
 obj-$(CONFIG_ARMADA_XP_CLK)	+= armada-xp.o
 obj-$(CONFIG_DOVE_CLK)		+= dove.o
 obj-$(CONFIG_KIRKWOOD_CLK)	+= kirkwood.o
diff --git a/drivers/clk/mvebu/armada-39x.c b/drivers/clk/mvebu/armada-39x.c
new file mode 100644
index 0000000..efb974d
--- /dev/null
+++ b/drivers/clk/mvebu/armada-39x.c
@@ -0,0 +1,156 @@
+/*
+ * Marvell Armada 39x SoC clocks
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+ * Andrew Lunn <andrew@lunn.ch>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include "common.h"
+
+/*
+ * SARL[14:10] : Ratios between CPU, NBCLK, HCLK and DCLK.
+ *
+ * SARL[15]    : TCLK frequency
+ *		 0 = 250 MHz
+ *		 1 = 200 MHz
+ *
+ * SARH[0]     : Reference clock frequency
+ *               0 = 25 Mhz
+ *               1 = 40 Mhz
+ */
+
+#define SARL 					0
+#define  SARL_A390_TCLK_FREQ_OPT		15
+#define  SARL_A390_TCLK_FREQ_OPT_MASK		0x1
+#define  SARL_A390_CPU_DDR_L2_FREQ_OPT		10
+#define  SARL_A390_CPU_DDR_L2_FREQ_OPT_MASK	0x1F
+#define SARH					4
+#define  SARH_A390_REFCLK_FREQ			BIT(0)
+
+static const u32 armada_39x_tclk_frequencies[] __initconst = {
+	250000000,
+	200000000,
+};
+
+static u32 __init armada_39x_get_tclk_freq(void __iomem *sar)
+{
+	u8 tclk_freq_select;
+
+	tclk_freq_select = ((readl(sar + SARL) >> SARL_A390_TCLK_FREQ_OPT) &
+			    SARL_A390_TCLK_FREQ_OPT_MASK);
+	return armada_39x_tclk_frequencies[tclk_freq_select];
+}
+
+static const u32 armada_39x_cpu_frequencies[] __initconst = {
+	[0x0] = 666 * 1000 * 1000,
+	[0x2] = 800 * 1000 * 1000,
+	[0x3] = 800 * 1000 * 1000,
+	[0x4] = 1066 * 1000 * 1000,
+	[0x5] = 1066 * 1000 * 1000,
+	[0x6] = 1200 * 1000 * 1000,
+	[0x8] = 1332 * 1000 * 1000,
+	[0xB] = 1600 * 1000 * 1000,
+	[0xC] = 1600 * 1000 * 1000,
+	[0x12] = 1800 * 1000 * 1000,
+	[0x1E] = 1800 * 1000 * 1000,
+};
+
+static u32 __init armada_39x_get_cpu_freq(void __iomem *sar)
+{
+	u8 cpu_freq_select;
+
+	cpu_freq_select = ((readl(sar + SARL) >> SARL_A390_CPU_DDR_L2_FREQ_OPT) &
+			   SARL_A390_CPU_DDR_L2_FREQ_OPT_MASK);
+	if (cpu_freq_select >= ARRAY_SIZE(armada_39x_cpu_frequencies)) {
+		pr_err("Selected CPU frequency (%d) unsupported\n",
+			cpu_freq_select);
+		return 0;
+	}
+
+	return armada_39x_cpu_frequencies[cpu_freq_select];
+}
+
+enum { A390_CPU_TO_NBCLK, A390_CPU_TO_HCLK, A390_CPU_TO_DCLK };
+
+static const struct coreclk_ratio armada_39x_coreclk_ratios[] __initconst = {
+	{ .id = A390_CPU_TO_NBCLK, .name = "nbclk" },
+	{ .id = A390_CPU_TO_HCLK, .name = "hclk" },
+	{ .id = A390_CPU_TO_DCLK, .name = "dclk" },
+};
+
+static void __init armada_39x_get_clk_ratio(
+	void __iomem *sar, int id, int *mult, int *div)
+{
+	switch (id) {
+	case A390_CPU_TO_NBCLK:
+		*mult = 1;
+		*div = 2;
+		break;
+	case A390_CPU_TO_HCLK:
+		*mult = 1;
+		*div = 4;
+		break;
+	case A390_CPU_TO_DCLK:
+		*mult = 1;
+		*div = 2;
+		break;
+	}
+}
+
+static u32 __init armada_39x_refclk_ratio(void __iomem *sar)
+{
+	if (readl(sar + SARH) & SARH_A390_REFCLK_FREQ)
+		return 40 * 1000 * 1000;
+	else
+		return 25 * 1000 * 1000;
+}
+
+static const struct coreclk_soc_desc armada_39x_coreclks = {
+	.get_tclk_freq = armada_39x_get_tclk_freq,
+	.get_cpu_freq = armada_39x_get_cpu_freq,
+	.get_clk_ratio = armada_39x_get_clk_ratio,
+	.get_refclk_freq = armada_39x_refclk_ratio,
+	.ratios = armada_39x_coreclk_ratios,
+	.num_ratios = ARRAY_SIZE(armada_39x_coreclk_ratios),
+};
+
+static void __init armada_39x_coreclk_init(struct device_node *np)
+{
+	mvebu_coreclk_setup(np, &armada_39x_coreclks);
+}
+CLK_OF_DECLARE(armada_39x_core_clk, "marvell,armada-390-core-clock",
+	       armada_39x_coreclk_init);
+
+/*
+ * Clock Gating Control
+ */
+static const struct clk_gating_soc_desc armada_39x_gating_desc[] __initconst = {
+	{ "pex1", NULL, 5 },
+	{ "pex2", NULL, 6 },
+	{ "pex3", NULL, 7 },
+	{ "pex0", NULL, 8 },
+	{ "usb3h0", NULL, 9 },
+	{ "sdio", NULL, 17 },
+	{ "xor0", NULL, 22 },
+	{ "xor1", NULL, 28 },
+	{ }
+};
+
+static void __init armada_39x_clk_gating_init(struct device_node *np)
+{
+	mvebu_clk_gating_setup(np, armada_39x_gating_desc);
+}
+CLK_OF_DECLARE(armada_39x_clk_gating, "marvell,armada-390-gating-clock",
+	       armada_39x_clk_gating_init);
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 06/10] clk: mvebu: add Marvell Armada 39x driver
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

This commit adds a new clock driver for the Marvell Armada 39x family
of processors. This driver is fairly similar to the ones already used
on other Marvell EBU processors, with the following main differences:

 * Different set of ratios
 * Different set of core clocks
 * Configurable reference clock in frequency

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 drivers/clk/mvebu/Kconfig      |   4 ++
 drivers/clk/mvebu/Makefile     |   1 +
 drivers/clk/mvebu/armada-39x.c | 156 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 161 insertions(+)
 create mode 100644 drivers/clk/mvebu/armada-39x.c

diff --git a/drivers/clk/mvebu/Kconfig b/drivers/clk/mvebu/Kconfig
index 3b34dba..2769625 100644
--- a/drivers/clk/mvebu/Kconfig
+++ b/drivers/clk/mvebu/Kconfig
@@ -21,6 +21,10 @@ config ARMADA_38X_CLK
 	bool
 	select MVEBU_CLK_COMMON
 
+config ARMADA_39X_CLK
+	bool
+	select MVEBU_CLK_COMMON
+
 config ARMADA_XP_CLK
 	bool
 	select MVEBU_CLK_COMMON
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
index a9a56fc..645ac7e 100644
--- a/drivers/clk/mvebu/Makefile
+++ b/drivers/clk/mvebu/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_MVEBU_CLK_COREDIV)	+= clk-corediv.o
 obj-$(CONFIG_ARMADA_370_CLK)	+= armada-370.o
 obj-$(CONFIG_ARMADA_375_CLK)	+= armada-375.o
 obj-$(CONFIG_ARMADA_38X_CLK)	+= armada-38x.o
+obj-$(CONFIG_ARMADA_39X_CLK)	+= armada-39x.o
 obj-$(CONFIG_ARMADA_XP_CLK)	+= armada-xp.o
 obj-$(CONFIG_DOVE_CLK)		+= dove.o
 obj-$(CONFIG_KIRKWOOD_CLK)	+= kirkwood.o
diff --git a/drivers/clk/mvebu/armada-39x.c b/drivers/clk/mvebu/armada-39x.c
new file mode 100644
index 0000000..efb974d
--- /dev/null
+++ b/drivers/clk/mvebu/armada-39x.c
@@ -0,0 +1,156 @@
+/*
+ * Marvell Armada 39x SoC clocks
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+ * Andrew Lunn <andrew@lunn.ch>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include "common.h"
+
+/*
+ * SARL[14:10] : Ratios between CPU, NBCLK, HCLK and DCLK.
+ *
+ * SARL[15]    : TCLK frequency
+ *		 0 = 250 MHz
+ *		 1 = 200 MHz
+ *
+ * SARH[0]     : Reference clock frequency
+ *               0 = 25 Mhz
+ *               1 = 40 Mhz
+ */
+
+#define SARL 					0
+#define  SARL_A390_TCLK_FREQ_OPT		15
+#define  SARL_A390_TCLK_FREQ_OPT_MASK		0x1
+#define  SARL_A390_CPU_DDR_L2_FREQ_OPT		10
+#define  SARL_A390_CPU_DDR_L2_FREQ_OPT_MASK	0x1F
+#define SARH					4
+#define  SARH_A390_REFCLK_FREQ			BIT(0)
+
+static const u32 armada_39x_tclk_frequencies[] __initconst = {
+	250000000,
+	200000000,
+};
+
+static u32 __init armada_39x_get_tclk_freq(void __iomem *sar)
+{
+	u8 tclk_freq_select;
+
+	tclk_freq_select = ((readl(sar + SARL) >> SARL_A390_TCLK_FREQ_OPT) &
+			    SARL_A390_TCLK_FREQ_OPT_MASK);
+	return armada_39x_tclk_frequencies[tclk_freq_select];
+}
+
+static const u32 armada_39x_cpu_frequencies[] __initconst = {
+	[0x0] = 666 * 1000 * 1000,
+	[0x2] = 800 * 1000 * 1000,
+	[0x3] = 800 * 1000 * 1000,
+	[0x4] = 1066 * 1000 * 1000,
+	[0x5] = 1066 * 1000 * 1000,
+	[0x6] = 1200 * 1000 * 1000,
+	[0x8] = 1332 * 1000 * 1000,
+	[0xB] = 1600 * 1000 * 1000,
+	[0xC] = 1600 * 1000 * 1000,
+	[0x12] = 1800 * 1000 * 1000,
+	[0x1E] = 1800 * 1000 * 1000,
+};
+
+static u32 __init armada_39x_get_cpu_freq(void __iomem *sar)
+{
+	u8 cpu_freq_select;
+
+	cpu_freq_select = ((readl(sar + SARL) >> SARL_A390_CPU_DDR_L2_FREQ_OPT) &
+			   SARL_A390_CPU_DDR_L2_FREQ_OPT_MASK);
+	if (cpu_freq_select >= ARRAY_SIZE(armada_39x_cpu_frequencies)) {
+		pr_err("Selected CPU frequency (%d) unsupported\n",
+			cpu_freq_select);
+		return 0;
+	}
+
+	return armada_39x_cpu_frequencies[cpu_freq_select];
+}
+
+enum { A390_CPU_TO_NBCLK, A390_CPU_TO_HCLK, A390_CPU_TO_DCLK };
+
+static const struct coreclk_ratio armada_39x_coreclk_ratios[] __initconst = {
+	{ .id = A390_CPU_TO_NBCLK, .name = "nbclk" },
+	{ .id = A390_CPU_TO_HCLK, .name = "hclk" },
+	{ .id = A390_CPU_TO_DCLK, .name = "dclk" },
+};
+
+static void __init armada_39x_get_clk_ratio(
+	void __iomem *sar, int id, int *mult, int *div)
+{
+	switch (id) {
+	case A390_CPU_TO_NBCLK:
+		*mult = 1;
+		*div = 2;
+		break;
+	case A390_CPU_TO_HCLK:
+		*mult = 1;
+		*div = 4;
+		break;
+	case A390_CPU_TO_DCLK:
+		*mult = 1;
+		*div = 2;
+		break;
+	}
+}
+
+static u32 __init armada_39x_refclk_ratio(void __iomem *sar)
+{
+	if (readl(sar + SARH) & SARH_A390_REFCLK_FREQ)
+		return 40 * 1000 * 1000;
+	else
+		return 25 * 1000 * 1000;
+}
+
+static const struct coreclk_soc_desc armada_39x_coreclks = {
+	.get_tclk_freq = armada_39x_get_tclk_freq,
+	.get_cpu_freq = armada_39x_get_cpu_freq,
+	.get_clk_ratio = armada_39x_get_clk_ratio,
+	.get_refclk_freq = armada_39x_refclk_ratio,
+	.ratios = armada_39x_coreclk_ratios,
+	.num_ratios = ARRAY_SIZE(armada_39x_coreclk_ratios),
+};
+
+static void __init armada_39x_coreclk_init(struct device_node *np)
+{
+	mvebu_coreclk_setup(np, &armada_39x_coreclks);
+}
+CLK_OF_DECLARE(armada_39x_core_clk, "marvell,armada-390-core-clock",
+	       armada_39x_coreclk_init);
+
+/*
+ * Clock Gating Control
+ */
+static const struct clk_gating_soc_desc armada_39x_gating_desc[] __initconst = {
+	{ "pex1", NULL, 5 },
+	{ "pex2", NULL, 6 },
+	{ "pex3", NULL, 7 },
+	{ "pex0", NULL, 8 },
+	{ "usb3h0", NULL, 9 },
+	{ "sdio", NULL, 17 },
+	{ "xor0", NULL, 22 },
+	{ "xor1", NULL, 28 },
+	{ }
+};
+
+static void __init armada_39x_clk_gating_init(struct device_node *np)
+{
+	mvebu_clk_gating_setup(np, armada_39x_gating_desc);
+}
+CLK_OF_DECLARE(armada_39x_clk_gating, "marvell,armada-390-gating-clock",
+	       armada_39x_clk_gating_init);
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

This commit adds a new pinctrl driver for the Marvell Armada 39x
family of processors, which hooks into the existing infrastructure to
support pin-muxing on Marvell EBU processors. Two variants of the
Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
398), which have a few differences in the available functions for
certain pins.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 drivers/pinctrl/mvebu/Kconfig              |   4 +
 drivers/pinctrl/mvebu/Makefile             |   1 +
 drivers/pinctrl/mvebu/pinctrl-armada-39x.c | 432 +++++++++++++++++++++++++++++
 3 files changed, 437 insertions(+)
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-39x.c

diff --git a/drivers/pinctrl/mvebu/Kconfig b/drivers/pinctrl/mvebu/Kconfig
index d6dd835..1706024 100644
--- a/drivers/pinctrl/mvebu/Kconfig
+++ b/drivers/pinctrl/mvebu/Kconfig
@@ -26,6 +26,10 @@ config PINCTRL_ARMADA_38X
 	bool
 	select PINCTRL_MVEBU
 
+config PINCTRL_ARMADA_39X
+	bool
+	select PINCTRL_MVEBU
+
 config PINCTRL_ARMADA_XP
 	bool
 	select PINCTRL_MVEBU
diff --git a/drivers/pinctrl/mvebu/Makefile b/drivers/pinctrl/mvebu/Makefile
index a0818e9..554d8af 100644
--- a/drivers/pinctrl/mvebu/Makefile
+++ b/drivers/pinctrl/mvebu/Makefile
@@ -4,5 +4,6 @@ obj-$(CONFIG_PINCTRL_KIRKWOOD)	+= pinctrl-kirkwood.o
 obj-$(CONFIG_PINCTRL_ARMADA_370) += pinctrl-armada-370.o
 obj-$(CONFIG_PINCTRL_ARMADA_375) += pinctrl-armada-375.o
 obj-$(CONFIG_PINCTRL_ARMADA_38X) += pinctrl-armada-38x.o
+obj-$(CONFIG_PINCTRL_ARMADA_39X) += pinctrl-armada-39x.o
 obj-$(CONFIG_PINCTRL_ARMADA_XP)  += pinctrl-armada-xp.o
 obj-$(CONFIG_PINCTRL_ORION)  += pinctrl-orion.o
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-39x.c b/drivers/pinctrl/mvebu/pinctrl-armada-39x.c
new file mode 100644
index 0000000..5963411
--- /dev/null
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-39x.c
@@ -0,0 +1,432 @@
+/*
+ * Marvell Armada 39x pinctrl driver based on mvebu pinctrl core
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-mvebu.h"
+
+static void __iomem *mpp_base;
+
+static int armada_39x_mpp_ctrl_get(unsigned pid, unsigned long *config)
+{
+	return default_mpp_ctrl_get(mpp_base, pid, config);
+}
+
+static int armada_39x_mpp_ctrl_set(unsigned pid, unsigned long config)
+{
+	return default_mpp_ctrl_set(mpp_base, pid, config);
+}
+
+enum {
+	V_88F6920 = BIT(0),
+	V_88F6928 = BIT(1),
+	V_88F6920_PLUS = (V_88F6920 | V_88F6928),
+};
+
+static struct mvebu_mpp_mode armada_39x_mpp_modes[] = {
+	MPP_MODE(0,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua0",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(1,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua0",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(2,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c0",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(3,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c0",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(4,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdc",      V_88F6920_PLUS)),
+	MPP_MODE(5,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdio",     V_88F6920_PLUS)),
+	MPP_MODE(6,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs3",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "xsmi",    "mdio",     V_88F6920_PLUS)),
+	MPP_MODE(7,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad9",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "xsmi",    "mdc",      V_88F6920_PLUS)),
+	MPP_MODE(8,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad10",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ptp",     "trig",     V_88F6920_PLUS)),
+	MPP_MODE(9,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad11",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ptp",     "clk",      V_88F6920_PLUS)),
+	MPP_MODE(10,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad12",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ptp",     "event",    V_88F6920_PLUS)),
+	MPP_MODE(11,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad13",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "clk",      V_88F6920_PLUS)),
+	MPP_MODE(12,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad14",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "stb",      V_88F6920_PLUS)),
+	MPP_MODE(13,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad15",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "data",     V_88F6920_PLUS)),
+	MPP_MODE(14,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "vtt",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "wen1",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(15,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "mosi",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c1",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(16,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "miso",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c1",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(17,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdio",     V_88F6920_PLUS)),
+	MPP_MODE(18,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "cs0",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c2",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(19,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(5, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c2",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(20,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(5, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdc",      V_88F6920_PLUS)),
+	MPP_MODE(21,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs1",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(4, "sd",      "cmd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "bootcs",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd0",     V_88F6920_PLUS)),
+	MPP_MODE(22,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "mosi",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad0",      V_88F6920_PLUS)),
+	MPP_MODE(23,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad2",      V_88F6920_PLUS)),
+	MPP_MODE(24,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "miso",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d4",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "readyn",   V_88F6920_PLUS)),
+	MPP_MODE(25,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs0",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d5",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs0",      V_88F6920_PLUS)),
+	MPP_MODE(26,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs2",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "i2c1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d6",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs1",      V_88F6920_PLUS)),
+	MPP_MODE(27,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs3",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "i2c1",    "sda",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d7",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs2",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txclkout", V_88F6920_PLUS)),
+	MPP_MODE(28,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad5",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd0",     V_88F6920_PLUS)),
+	MPP_MODE(29,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ale0",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd1",     V_88F6920_PLUS)),
+	MPP_MODE(30,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "oen",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd2",     V_88F6920_PLUS)),
+	MPP_MODE(31,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ale1",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd3",     V_88F6920_PLUS)),
+	MPP_MODE(32,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "wen0",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txctl",    V_88F6920_PLUS)),
+	MPP_MODE(33,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad3",      V_88F6920_PLUS)),
+	MPP_MODE(34,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad1",      V_88F6920_PLUS)),
+	MPP_MODE(35,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "a1",       V_88F6920_PLUS)),
+	MPP_MODE(36,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "a0",       V_88F6920_PLUS)),
+	MPP_MODE(37,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d3",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad8",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxclk",    V_88F6920_PLUS)),
+	MPP_MODE(38,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d0",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad4",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd1",     V_88F6920_PLUS)),
+	MPP_MODE(39,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d1",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "a2",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd2",     V_88F6920_PLUS)),
+	MPP_MODE(40,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c1",    "sda",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d2",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad6",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd3",     V_88F6920_PLUS)),
+	MPP_MODE(41,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs3",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "burstn",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "nd",      "rbn0",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxctl",    V_88F6920_PLUS)),
+	MPP_MODE(42,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad7",      V_88F6920_PLUS)),
+	MPP_MODE(43,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "clkreq",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "m",       "vtt",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs2",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "clkout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "nd",      "rbn1",     V_88F6920_PLUS)),
+	MPP_MODE(44,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(7, "led",     "clk",      V_88F6920_PLUS)),
+	MPP_MODE(45,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(46,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "stb",      V_88F6920_PLUS)),
+	MPP_MODE(47,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(7, "led",     "data",     V_88F6920_PLUS)),
+	MPP_MODE(48,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "m",       "vtt",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "pclk",     V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "mclk",     V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d4",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "pcie0",   "clkreq",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(49,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "fsync",    V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "lrclk",    V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d5",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua2",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(50,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "drx",      V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "extclk",   V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "cmd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua2",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(51,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "dtx",      V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "sdo",      V_88F6928),
+		 MPP_VAR_FUNCTION(5, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua2",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(52,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "intn",     V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "sdi",      V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d6",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c3",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(53,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(3, "tdm",     "rstn",     V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "bclk",     V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d7",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c3",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(54,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(3, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d3",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua3",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(55,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs1",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d0",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua3",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(56,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "mosi",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(57,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(58,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "i2c1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "pcie2",   "clkreq",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "miso",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d1",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(59,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "i2c1",    "sda",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs0",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d2",       V_88F6920_PLUS)),
+};
+
+static struct mvebu_pinctrl_soc_info armada_39x_pinctrl_info;
+
+static struct of_device_id armada_39x_pinctrl_of_match[] = {
+	{
+		.compatible = "marvell,mv88f6920-pinctrl",
+		.data       = (void *) V_88F6920,
+	},
+	{
+		.compatible = "marvell,mv88f6928-pinctrl",
+		.data       = (void *) V_88F6928,
+	},
+	{ },
+};
+
+static struct mvebu_mpp_ctrl armada_39x_mpp_controls[] = {
+	MPP_FUNC_CTRL(0, 59, NULL, armada_39x_mpp_ctrl),
+};
+
+static struct pinctrl_gpio_range armada_39x_mpp_gpio_ranges[] = {
+	MPP_GPIO_RANGE(0,   0,  0, 32),
+	MPP_GPIO_RANGE(1,  32, 32, 27),
+};
+
+static int armada_39x_pinctrl_probe(struct platform_device *pdev)
+{
+	struct mvebu_pinctrl_soc_info *soc = &armada_39x_pinctrl_info;
+	const struct of_device_id *match =
+		of_match_device(armada_39x_pinctrl_of_match, &pdev->dev);
+	struct resource *res;
+
+	if (!match)
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mpp_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mpp_base))
+		return PTR_ERR(mpp_base);
+
+	soc->variant = (unsigned) match->data & 0xff;
+	soc->controls = armada_39x_mpp_controls;
+	soc->ncontrols = ARRAY_SIZE(armada_39x_mpp_controls);
+	soc->gpioranges = armada_39x_mpp_gpio_ranges;
+	soc->ngpioranges = ARRAY_SIZE(armada_39x_mpp_gpio_ranges);
+	soc->modes = armada_39x_mpp_modes;
+	soc->nmodes = armada_39x_mpp_controls[0].npins;
+
+	pdev->dev.platform_data = soc;
+
+	return mvebu_pinctrl_probe(pdev);
+}
+
+static int armada_39x_pinctrl_remove(struct platform_device *pdev)
+{
+	return mvebu_pinctrl_remove(pdev);
+}
+
+static struct platform_driver armada_39x_pinctrl_driver = {
+	.driver = {
+		.name = "armada-39x-pinctrl",
+		.of_match_table = of_match_ptr(armada_39x_pinctrl_of_match),
+	},
+	.probe = armada_39x_pinctrl_probe,
+	.remove = armada_39x_pinctrl_remove,
+};
+
+module_platform_driver(armada_39x_pinctrl_driver);
+
+MODULE_AUTHOR("Thomas Petazzoni <thomas.petazzoni@free-electrons.com>");
+MODULE_DESCRIPTION("Marvell Armada 39x pinctrl driver");
+MODULE_LICENSE("GPL v2");
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

This commit adds a new pinctrl driver for the Marvell Armada 39x
family of processors, which hooks into the existing infrastructure to
support pin-muxing on Marvell EBU processors. Two variants of the
Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
398), which have a few differences in the available functions for
certain pins.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 drivers/pinctrl/mvebu/Kconfig              |   4 +
 drivers/pinctrl/mvebu/Makefile             |   1 +
 drivers/pinctrl/mvebu/pinctrl-armada-39x.c | 432 +++++++++++++++++++++++++++++
 3 files changed, 437 insertions(+)
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-39x.c

diff --git a/drivers/pinctrl/mvebu/Kconfig b/drivers/pinctrl/mvebu/Kconfig
index d6dd835..1706024 100644
--- a/drivers/pinctrl/mvebu/Kconfig
+++ b/drivers/pinctrl/mvebu/Kconfig
@@ -26,6 +26,10 @@ config PINCTRL_ARMADA_38X
 	bool
 	select PINCTRL_MVEBU
 
+config PINCTRL_ARMADA_39X
+	bool
+	select PINCTRL_MVEBU
+
 config PINCTRL_ARMADA_XP
 	bool
 	select PINCTRL_MVEBU
diff --git a/drivers/pinctrl/mvebu/Makefile b/drivers/pinctrl/mvebu/Makefile
index a0818e9..554d8af 100644
--- a/drivers/pinctrl/mvebu/Makefile
+++ b/drivers/pinctrl/mvebu/Makefile
@@ -4,5 +4,6 @@ obj-$(CONFIG_PINCTRL_KIRKWOOD)	+= pinctrl-kirkwood.o
 obj-$(CONFIG_PINCTRL_ARMADA_370) += pinctrl-armada-370.o
 obj-$(CONFIG_PINCTRL_ARMADA_375) += pinctrl-armada-375.o
 obj-$(CONFIG_PINCTRL_ARMADA_38X) += pinctrl-armada-38x.o
+obj-$(CONFIG_PINCTRL_ARMADA_39X) += pinctrl-armada-39x.o
 obj-$(CONFIG_PINCTRL_ARMADA_XP)  += pinctrl-armada-xp.o
 obj-$(CONFIG_PINCTRL_ORION)  += pinctrl-orion.o
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-39x.c b/drivers/pinctrl/mvebu/pinctrl-armada-39x.c
new file mode 100644
index 0000000..5963411
--- /dev/null
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-39x.c
@@ -0,0 +1,432 @@
+/*
+ * Marvell Armada 39x pinctrl driver based on mvebu pinctrl core
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-mvebu.h"
+
+static void __iomem *mpp_base;
+
+static int armada_39x_mpp_ctrl_get(unsigned pid, unsigned long *config)
+{
+	return default_mpp_ctrl_get(mpp_base, pid, config);
+}
+
+static int armada_39x_mpp_ctrl_set(unsigned pid, unsigned long config)
+{
+	return default_mpp_ctrl_set(mpp_base, pid, config);
+}
+
+enum {
+	V_88F6920 = BIT(0),
+	V_88F6928 = BIT(1),
+	V_88F6920_PLUS = (V_88F6920 | V_88F6928),
+};
+
+static struct mvebu_mpp_mode armada_39x_mpp_modes[] = {
+	MPP_MODE(0,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua0",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(1,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua0",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(2,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c0",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(3,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c0",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(4,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdc",      V_88F6920_PLUS)),
+	MPP_MODE(5,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdio",     V_88F6920_PLUS)),
+	MPP_MODE(6,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs3",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "xsmi",    "mdio",     V_88F6920_PLUS)),
+	MPP_MODE(7,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad9",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "xsmi",    "mdc",      V_88F6920_PLUS)),
+	MPP_MODE(8,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad10",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ptp",     "trig",     V_88F6920_PLUS)),
+	MPP_MODE(9,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad11",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ptp",     "clk",      V_88F6920_PLUS)),
+	MPP_MODE(10,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad12",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ptp",     "event",    V_88F6920_PLUS)),
+	MPP_MODE(11,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad13",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "clk",      V_88F6920_PLUS)),
+	MPP_MODE(12,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad14",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "stb",      V_88F6920_PLUS)),
+	MPP_MODE(13,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad15",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "data",     V_88F6920_PLUS)),
+	MPP_MODE(14,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "vtt",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "wen1",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(15,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "mosi",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c1",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(16,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "miso",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c1",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(17,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdio",     V_88F6920_PLUS)),
+	MPP_MODE(18,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi0",    "cs0",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c2",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(19,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(5, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c2",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(20,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(5, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "smi",     "mdc",      V_88F6920_PLUS)),
+	MPP_MODE(21,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs1",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(4, "sd",      "cmd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "bootcs",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd0",     V_88F6920_PLUS)),
+	MPP_MODE(22,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "mosi",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad0",      V_88F6920_PLUS)),
+	MPP_MODE(23,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad2",      V_88F6920_PLUS)),
+	MPP_MODE(24,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "miso",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d4",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "readyn",   V_88F6920_PLUS)),
+	MPP_MODE(25,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs0",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d5",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs0",      V_88F6920_PLUS)),
+	MPP_MODE(26,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs2",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "i2c1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d6",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs1",      V_88F6920_PLUS)),
+	MPP_MODE(27,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "spi0",    "cs3",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "i2c1",    "sda",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d7",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "cs2",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txclkout", V_88F6920_PLUS)),
+	MPP_MODE(28,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad5",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd0",     V_88F6920_PLUS)),
+	MPP_MODE(29,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ale0",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd1",     V_88F6920_PLUS)),
+	MPP_MODE(30,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "oen",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd2",     V_88F6920_PLUS)),
+	MPP_MODE(31,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ale1",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txd3",     V_88F6920_PLUS)),
+	MPP_MODE(32,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "wen0",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "txctl",    V_88F6920_PLUS)),
+	MPP_MODE(33,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad3",      V_88F6920_PLUS)),
+	MPP_MODE(34,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad1",      V_88F6920_PLUS)),
+	MPP_MODE(35,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "a1",       V_88F6920_PLUS)),
+	MPP_MODE(36,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "a0",       V_88F6920_PLUS)),
+	MPP_MODE(37,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d3",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad8",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxclk",    V_88F6920_PLUS)),
+	MPP_MODE(38,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d0",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad4",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd1",     V_88F6920_PLUS)),
+	MPP_MODE(39,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d1",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "a2",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd2",     V_88F6920_PLUS)),
+	MPP_MODE(40,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "i2c1",    "sda",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "sd",      "d2",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad6",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxd3",     V_88F6920_PLUS)),
+	MPP_MODE(41,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs3",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "burstn",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "nd",      "rbn0",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(8, "ge",      "rxctl",    V_88F6920_PLUS)),
+	MPP_MODE(42,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "ua0",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "ad7",      V_88F6920_PLUS)),
+	MPP_MODE(43,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "clkreq",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "m",       "vtt",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs2",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "dev",     "clkout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "nd",      "rbn1",     V_88F6920_PLUS)),
+	MPP_MODE(44,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(7, "led",     "clk",      V_88F6920_PLUS)),
+	MPP_MODE(45,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(46,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ref",     "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "led",     "stb",      V_88F6920_PLUS)),
+	MPP_MODE(47,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(7, "led",     "data",     V_88F6920_PLUS)),
+	MPP_MODE(48,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "m",       "vtt",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "pclk",     V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "mclk",     V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d4",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "pcie0",   "clkreq",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(49,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "fsync",    V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "lrclk",    V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d5",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua2",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(50,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "drx",      V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "extclk",   V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "cmd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua2",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(51,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "dtx",      V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "sdo",      V_88F6928),
+		 MPP_VAR_FUNCTION(5, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua2",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(52,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "tdm",     "intn",     V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "sdi",      V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d6",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c3",    "sck",      V_88F6920_PLUS)),
+	MPP_MODE(53,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(3, "tdm",     "rstn",     V_88F6928),
+		 MPP_VAR_FUNCTION(4, "audio",   "bclk",     V_88F6928),
+		 MPP_VAR_FUNCTION(5, "sd",      "d7",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "i2c3",    "sda",      V_88F6920_PLUS)),
+	MPP_MODE(54,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "sata0",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(2, "sata1",   "present",  V_88F6928),
+		 MPP_VAR_FUNCTION(3, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d3",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua3",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(55,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "cts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs1",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d0",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(7, "ua3",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(56,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "ua1",     "rts",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "m",       "decc",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "mosi",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(57,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "clk",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "txd",      V_88F6920_PLUS)),
+	MPP_MODE(58,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "i2c1",    "sck",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(3, "pcie2",   "clkreq",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "miso",     V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d1",       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(6, "ua1",     "rxd",      V_88F6920_PLUS)),
+	MPP_MODE(59,
+		 MPP_VAR_FUNCTION(0, "gpio",    NULL,       V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(1, "pcie0",   "rstout",   V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(2, "i2c1",    "sda",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(4, "spi1",    "cs0",      V_88F6920_PLUS),
+		 MPP_VAR_FUNCTION(5, "sd",      "d2",       V_88F6920_PLUS)),
+};
+
+static struct mvebu_pinctrl_soc_info armada_39x_pinctrl_info;
+
+static struct of_device_id armada_39x_pinctrl_of_match[] = {
+	{
+		.compatible = "marvell,mv88f6920-pinctrl",
+		.data       = (void *) V_88F6920,
+	},
+	{
+		.compatible = "marvell,mv88f6928-pinctrl",
+		.data       = (void *) V_88F6928,
+	},
+	{ },
+};
+
+static struct mvebu_mpp_ctrl armada_39x_mpp_controls[] = {
+	MPP_FUNC_CTRL(0, 59, NULL, armada_39x_mpp_ctrl),
+};
+
+static struct pinctrl_gpio_range armada_39x_mpp_gpio_ranges[] = {
+	MPP_GPIO_RANGE(0,   0,  0, 32),
+	MPP_GPIO_RANGE(1,  32, 32, 27),
+};
+
+static int armada_39x_pinctrl_probe(struct platform_device *pdev)
+{
+	struct mvebu_pinctrl_soc_info *soc = &armada_39x_pinctrl_info;
+	const struct of_device_id *match =
+		of_match_device(armada_39x_pinctrl_of_match, &pdev->dev);
+	struct resource *res;
+
+	if (!match)
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mpp_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mpp_base))
+		return PTR_ERR(mpp_base);
+
+	soc->variant = (unsigned) match->data & 0xff;
+	soc->controls = armada_39x_mpp_controls;
+	soc->ncontrols = ARRAY_SIZE(armada_39x_mpp_controls);
+	soc->gpioranges = armada_39x_mpp_gpio_ranges;
+	soc->ngpioranges = ARRAY_SIZE(armada_39x_mpp_gpio_ranges);
+	soc->modes = armada_39x_mpp_modes;
+	soc->nmodes = armada_39x_mpp_controls[0].npins;
+
+	pdev->dev.platform_data = soc;
+
+	return mvebu_pinctrl_probe(pdev);
+}
+
+static int armada_39x_pinctrl_remove(struct platform_device *pdev)
+{
+	return mvebu_pinctrl_remove(pdev);
+}
+
+static struct platform_driver armada_39x_pinctrl_driver = {
+	.driver = {
+		.name = "armada-39x-pinctrl",
+		.of_match_table = of_match_ptr(armada_39x_pinctrl_of_match),
+	},
+	.probe = armada_39x_pinctrl_probe,
+	.remove = armada_39x_pinctrl_remove,
+};
+
+module_platform_driver(armada_39x_pinctrl_driver);
+
+MODULE_AUTHOR("Thomas Petazzoni <thomas.petazzoni@free-electrons.com>");
+MODULE_DESCRIPTION("Marvell Armada 39x pinctrl driver");
+MODULE_LICENSE("GPL v2");
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57   ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

This commit adds the core support for Armada 39x, which is quite
simple:

 - a new Kconfig option which selects the appropriate clock and
   pinctrl drivers as well as other common features (GIC, L2 cache,
   SMP, etc.)

 - a new DT_MACHINE_START which references the top-level compatible
   strings supported for the Marvell Armada 39x.

 - a new SMP enable-method. The mechanism to enable CPUs for Armada
   39x appears to be the same as Armada 38x. However, we do want to
   use marvell,armada-380-smp in the Device Tree, in the case of the
   discovery of a subtle difference in the future, which would require
   changing the Device Tree. And the enable-method isn't a compatible
   string: you can't specify several values and expect a fallback on
   the second string if the first one isn't supported. Therefore, we
   simply declare the SMP enable method "marvell,armada-390-smp" as
   doing the same thing as the "marvell,armada-380-smp" one.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 arch/arm/mach-mvebu/Kconfig      | 14 ++++++++++++++
 arch/arm/mach-mvebu/board-v7.c   | 14 ++++++++++++++
 arch/arm/mach-mvebu/platsmp-a9.c |  2 ++
 3 files changed, 30 insertions(+)

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index c1e4567..9747316 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -64,6 +64,20 @@ config MACH_ARMADA_38X
 	  Say 'Y' here if you want your kernel to support boards based
 	  on the Marvell Armada 380/385 SoC with device tree.
 
+config MACH_ARMADA_39X
+	bool "Marvell Armada 39x boards" if ARCH_MULTI_V7
+	select ARM_GIC
+	select ARMADA_39X_CLK
+	select CACHE_L2X0
+	select HAVE_ARM_SCU
+	select HAVE_ARM_TWD if SMP
+	select HAVE_SMP
+	select MACH_MVEBU_V7
+	select PINCTRL_ARMADA_39X
+	help
+	  Say 'Y' here if you want your kernel to support boards based
+	  on the Marvell Armada 39x SoC with device tree.
+
 config MACH_ARMADA_XP
 	bool "Marvell Armada XP boards" if ARCH_MULTI_V7
 	select ARMADA_XP_CLK
diff --git a/arch/arm/mach-mvebu/board-v7.c b/arch/arm/mach-mvebu/board-v7.c
index 89a139e..d88438f 100644
--- a/arch/arm/mach-mvebu/board-v7.c
+++ b/arch/arm/mach-mvebu/board-v7.c
@@ -232,3 +232,17 @@ DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)")
 	.restart	= mvebu_restart,
 	.dt_compat	= armada_38x_dt_compat,
 MACHINE_END
+
+static const char * const armada_39x_dt_compat[] = {
+	"marvell,armada390",
+	"marvell,armada398",
+	NULL,
+};
+
+DT_MACHINE_START(ARMADA_39X_DT, "Marvell Armada 39x (Device Tree)")
+	.l2c_aux_val	= 0,
+	.l2c_aux_mask	= ~0,
+	.init_irq       = mvebu_init_irq,
+	.restart	= mvebu_restart,
+	.dt_compat	= armada_39x_dt_compat,
+MACHINE_END
diff --git a/arch/arm/mach-mvebu/platsmp-a9.c b/arch/arm/mach-mvebu/platsmp-a9.c
index 2ec1a42..df0a9cc 100644
--- a/arch/arm/mach-mvebu/platsmp-a9.c
+++ b/arch/arm/mach-mvebu/platsmp-a9.c
@@ -110,3 +110,5 @@ CPU_METHOD_OF_DECLARE(mvebu_armada_375_smp, "marvell,armada-375-smp",
 		      &mvebu_cortex_a9_smp_ops);
 CPU_METHOD_OF_DECLARE(mvebu_armada_380_smp, "marvell,armada-380-smp",
 		      &armada_38x_smp_ops);
+CPU_METHOD_OF_DECLARE(mvebu_armada_390_smp, "marvell,armada-390-smp",
+		      &armada_38x_smp_ops);
-- 
2.1.0


^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
@ 2015-02-06 15:57   ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

This commit adds the core support for Armada 39x, which is quite
simple:

 - a new Kconfig option which selects the appropriate clock and
   pinctrl drivers as well as other common features (GIC, L2 cache,
   SMP, etc.)

 - a new DT_MACHINE_START which references the top-level compatible
   strings supported for the Marvell Armada 39x.

 - a new SMP enable-method. The mechanism to enable CPUs for Armada
   39x appears to be the same as Armada 38x. However, we do want to
   use marvell,armada-380-smp in the Device Tree, in the case of the
   discovery of a subtle difference in the future, which would require
   changing the Device Tree. And the enable-method isn't a compatible
   string: you can't specify several values and expect a fallback on
   the second string if the first one isn't supported. Therefore, we
   simply declare the SMP enable method "marvell,armada-390-smp" as
   doing the same thing as the "marvell,armada-380-smp" one.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 arch/arm/mach-mvebu/Kconfig      | 14 ++++++++++++++
 arch/arm/mach-mvebu/board-v7.c   | 14 ++++++++++++++
 arch/arm/mach-mvebu/platsmp-a9.c |  2 ++
 3 files changed, 30 insertions(+)

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index c1e4567..9747316 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -64,6 +64,20 @@ config MACH_ARMADA_38X
 	  Say 'Y' here if you want your kernel to support boards based
 	  on the Marvell Armada 380/385 SoC with device tree.
 
+config MACH_ARMADA_39X
+	bool "Marvell Armada 39x boards" if ARCH_MULTI_V7
+	select ARM_GIC
+	select ARMADA_39X_CLK
+	select CACHE_L2X0
+	select HAVE_ARM_SCU
+	select HAVE_ARM_TWD if SMP
+	select HAVE_SMP
+	select MACH_MVEBU_V7
+	select PINCTRL_ARMADA_39X
+	help
+	  Say 'Y' here if you want your kernel to support boards based
+	  on the Marvell Armada 39x SoC with device tree.
+
 config MACH_ARMADA_XP
 	bool "Marvell Armada XP boards" if ARCH_MULTI_V7
 	select ARMADA_XP_CLK
diff --git a/arch/arm/mach-mvebu/board-v7.c b/arch/arm/mach-mvebu/board-v7.c
index 89a139e..d88438f 100644
--- a/arch/arm/mach-mvebu/board-v7.c
+++ b/arch/arm/mach-mvebu/board-v7.c
@@ -232,3 +232,17 @@ DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)")
 	.restart	= mvebu_restart,
 	.dt_compat	= armada_38x_dt_compat,
 MACHINE_END
+
+static const char * const armada_39x_dt_compat[] = {
+	"marvell,armada390",
+	"marvell,armada398",
+	NULL,
+};
+
+DT_MACHINE_START(ARMADA_39X_DT, "Marvell Armada 39x (Device Tree)")
+	.l2c_aux_val	= 0,
+	.l2c_aux_mask	= ~0,
+	.init_irq       = mvebu_init_irq,
+	.restart	= mvebu_restart,
+	.dt_compat	= armada_39x_dt_compat,
+MACHINE_END
diff --git a/arch/arm/mach-mvebu/platsmp-a9.c b/arch/arm/mach-mvebu/platsmp-a9.c
index 2ec1a42..df0a9cc 100644
--- a/arch/arm/mach-mvebu/platsmp-a9.c
+++ b/arch/arm/mach-mvebu/platsmp-a9.c
@@ -110,3 +110,5 @@ CPU_METHOD_OF_DECLARE(mvebu_armada_375_smp, "marvell,armada-375-smp",
 		      &mvebu_cortex_a9_smp_ops);
 CPU_METHOD_OF_DECLARE(mvebu_armada_380_smp, "marvell,armada-380-smp",
 		      &armada_38x_smp_ops);
+CPU_METHOD_OF_DECLARE(mvebu_armada_390_smp, "marvell,armada-390-smp",
+		      &armada_38x_smp_ops);
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57     ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
	Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linux-gpio-u79uwXL29TY76Z2rM5mHXA, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.

Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.

Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.

So far, the following features are supported:

 * SMP: dual Cortex-A9
 * Basic ARM IPs: SCU, timer, GIC
 * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
   controller, MPIC interrupt controller, timer, CPU reset for SMP,
   PMSU.
 * I2C
 * UART
 * PCIe

Additional features will be supported in the future.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/boot/dts/Makefile          |   2 +
 arch/arm/boot/dts/armada-390.dtsi   |  57 ++++++
 arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++
 arch/arm/boot/dts/armada-398.dtsi   |  60 ++++++
 arch/arm/boot/dts/armada-39x.dtsi   | 372 ++++++++++++++++++++++++++++++++++++
 5 files changed, 607 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-390.dtsi
 create mode 100644 arch/arm/boot/dts/armada-398-db.dts
 create mode 100644 arch/arm/boot/dts/armada-398.dtsi
 create mode 100644 arch/arm/boot/dts/armada-39x.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 968bc7a..64886fb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
 	armada-388-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_39X) += \
+	armada-398-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_XP) += \
 	armada-xp-axpwifiap.dtb \
 	armada-xp-db.dtb \
diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi
new file mode 100644
index 0000000..094e39c
--- /dev/null
+++ b/arch/arm/boot/dts/armada-390.dtsi
@@ -0,0 +1,57 @@
+/*
+ * Device Tree Include file for Marvell Armada 390 SoC.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armada-39x.dtsi"
+
+/ {
+	soc {
+		internal-regs {
+			pinctrl@18000 {
+				compatible = "marvell,mv88f6920-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+};
diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
new file mode 100644
index 0000000..b889864
--- /dev/null
+++ b/arch/arm/boot/dts/armada-398-db.dts
@@ -0,0 +1,116 @@
+/*
+ * Device Tree Include file for Marvell Armada 398 Development Board
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-398.dtsi"
+
+/ {
+	model = "Marvell Armada 398 Development Board";
+	compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000>; /* 2 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+                        i2c@11000 {
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+                                status = "okay";
+                                clock-frequency = <100000>;
+                        };
+
+			serial@12000 {
+				pinctrl-0 = <&uart0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			serial@12100 {
+				pinctrl-0 = <&uart1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				uart0_pins: uart0-pins {
+					marvell,pins = "mpp0", "mpp1";
+					marvell,function = "ua0";
+				};
+
+				uart1_pins: uart1-pins {
+					marvell,pins = "mpp19", "mpp20";
+					marvell,function = "ua1";
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				status = "okay";
+			};
+
+			pcie@3,0 {
+				status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi
new file mode 100644
index 0000000..fdc2591
--- /dev/null
+++ b/arch/arm/boot/dts/armada-398.dtsi
@@ -0,0 +1,60 @@
+/*
+ * Device Tree Include file for Marvell Armada 398 SoC.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armada-39x.dtsi"
+
+/ {
+	compatible = "marvell,armada398", "marvell,armada390";
+
+	soc {
+		internal-regs {
+			pinctrl@18000 {
+				compatible = "marvell,mv88f6928-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
new file mode 100644
index 0000000..e248332
--- /dev/null
+++ b/arch/arm/boot/dts/armada-39x.dtsi
@@ -0,0 +1,372 @@
+/*
+ * Device Tree Include file for Marvell Armada 39x family of SoCs.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 39x family SoC";
+	compatible = "marvell,armada390";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-390-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus",
+			     "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&gic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			scu@c000 {
+				compatible = "arm,cortex-a9-scu";
+				reg = <0xc000 0x100>;
+			};
+
+			timer@c600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xc600 0x20>;
+				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+				clocks = <&coreclk 2>;
+			};
+
+			gic: interrupt-controller@d000 {
+				compatible = "arm,cortex-a9-gic";
+				#interrupt-cells = <3>;
+				#size-cells = <0>;
+				interrupt-controller;
+				reg = <0xd000 0x1000>,
+				      <0xc100 0x100>;
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@11200 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11200 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@11300 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11300 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12200 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12200 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12300 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12300 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			pinctrl@18000 {
+				i2c0_pins: i2c0-pins {
+					marvell,pins = "mpp2", "mpp3";
+					marvell,function = "i2c0";
+				};
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-390-system-controller",
+					     "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-390-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			coreclk: mvebu-sar@18600 {
+				compatible = "marvell,armada-390-core-clock";
+				reg = <0x18600 0x04>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>;
+			};
+
+			mpic: interrupt-controller@20000 {
+				compatible = "marvell,mpic";
+				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			timer@20300 {
+				compatible = "marvell,armada-380-timer",
+					     "marvell,armada-xp-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+						      <&mpic 5>,
+						      <&mpic 6>;
+				clocks = <&coreclk 2>, <&coreclk 5>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			cpurst@20800 {
+				compatible = "marvell,armada-370-cpu-reset";
+				reg = <0x20800 0x10>;
+			};
+
+			pmsu@22000 {
+				compatible = "marvell,armada-390-pmsu",
+					     "marvell,armada-380-pmsu";
+				reg = <0x22000 0x1000>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
+
+			/*
+			 * This port can be either x4 or x1. When
+			 * configured in x4 by the bootloader, then
+			 * pcie@4,0 is not available.
+			 */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			/*
+			 * x1 port only available when pcie@1,0 is
+			 * configured as a x1 port
+			 */
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+		};
+	};
+};
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
@ 2015-02-06 15:57     ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.

Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.

Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.

So far, the following features are supported:

 * SMP: dual Cortex-A9
 * Basic ARM IPs: SCU, timer, GIC
 * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
   controller, MPIC interrupt controller, timer, CPU reset for SMP,
   PMSU.
 * I2C
 * UART
 * PCIe

Additional features will be supported in the future.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 arch/arm/boot/dts/Makefile          |   2 +
 arch/arm/boot/dts/armada-390.dtsi   |  57 ++++++
 arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++
 arch/arm/boot/dts/armada-398.dtsi   |  60 ++++++
 arch/arm/boot/dts/armada-39x.dtsi   | 372 ++++++++++++++++++++++++++++++++++++
 5 files changed, 607 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-390.dtsi
 create mode 100644 arch/arm/boot/dts/armada-398-db.dts
 create mode 100644 arch/arm/boot/dts/armada-398.dtsi
 create mode 100644 arch/arm/boot/dts/armada-39x.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 968bc7a..64886fb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
 	armada-388-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_39X) += \
+	armada-398-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_XP) += \
 	armada-xp-axpwifiap.dtb \
 	armada-xp-db.dtb \
diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi
new file mode 100644
index 0000000..094e39c
--- /dev/null
+++ b/arch/arm/boot/dts/armada-390.dtsi
@@ -0,0 +1,57 @@
+/*
+ * Device Tree Include file for Marvell Armada 390 SoC.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armada-39x.dtsi"
+
+/ {
+	soc {
+		internal-regs {
+			pinctrl at 18000 {
+				compatible = "marvell,mv88f6920-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+};
diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
new file mode 100644
index 0000000..b889864
--- /dev/null
+++ b/arch/arm/boot/dts/armada-398-db.dts
@@ -0,0 +1,116 @@
+/*
+ * Device Tree Include file for Marvell Armada 398 Development Board
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-398.dtsi"
+
+/ {
+	model = "Marvell Armada 398 Development Board";
+	compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000>; /* 2 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+                        i2c at 11000 {
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+                                status = "okay";
+                                clock-frequency = <100000>;
+                        };
+
+			serial at 12000 {
+				pinctrl-0 = <&uart0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			serial at 12100 {
+				pinctrl-0 = <&uart1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			pinctrl at 18000 {
+				uart0_pins: uart0-pins {
+					marvell,pins = "mpp0", "mpp1";
+					marvell,function = "ua0";
+				};
+
+				uart1_pins: uart1-pins {
+					marvell,pins = "mpp19", "mpp20";
+					marvell,function = "ua1";
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie at 1,0 {
+				status = "okay";
+			};
+
+			pcie at 2,0 {
+				status = "okay";
+			};
+
+			pcie at 3,0 {
+				status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi
new file mode 100644
index 0000000..fdc2591
--- /dev/null
+++ b/arch/arm/boot/dts/armada-398.dtsi
@@ -0,0 +1,60 @@
+/*
+ * Device Tree Include file for Marvell Armada 398 SoC.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armada-39x.dtsi"
+
+/ {
+	compatible = "marvell,armada398", "marvell,armada390";
+
+	soc {
+		internal-regs {
+			pinctrl at 18000 {
+				compatible = "marvell,mv88f6928-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
new file mode 100644
index 0000000..e248332
--- /dev/null
+++ b/arch/arm/boot/dts/armada-39x.dtsi
@@ -0,0 +1,372 @@
+/*
+ * Device Tree Include file for Marvell Armada 39x family of SoCs.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 39x family SoC";
+	compatible = "marvell,armada390";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-390-smp";
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+		cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus",
+			     "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&gic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			scu at c000 {
+				compatible = "arm,cortex-a9-scu";
+				reg = <0xc000 0x100>;
+			};
+
+			timer at c600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xc600 0x20>;
+				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+				clocks = <&coreclk 2>;
+			};
+
+			gic: interrupt-controller at d000 {
+				compatible = "arm,cortex-a9-gic";
+				#interrupt-cells = <3>;
+				#size-cells = <0>;
+				interrupt-controller;
+				reg = <0xd000 0x1000>,
+				      <0xc100 0x100>;
+			};
+
+			i2c0: i2c at 11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c at 11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c at 11200 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11200 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c3: i2c at 11300 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11300 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial at 12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial at 12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial at 12200 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12200 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial at 12300 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12300 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			pinctrl at 18000 {
+				i2c0_pins: i2c0-pins {
+					marvell,pins = "mpp2", "mpp3";
+					marvell,function = "i2c0";
+				};
+			};
+
+			system-controller at 18200 {
+				compatible = "marvell,armada-390-system-controller",
+					     "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
+			gateclk: clock-gating-control at 18220 {
+				compatible = "marvell,armada-390-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			coreclk: mvebu-sar at 18600 {
+				compatible = "marvell,armada-390-core-clock";
+				reg = <0x18600 0x04>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller at 20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>;
+			};
+
+			mpic: interrupt-controller at 20000 {
+				compatible = "marvell,mpic";
+				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			timer at 20300 {
+				compatible = "marvell,armada-380-timer",
+					     "marvell,armada-xp-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+						      <&mpic 5>,
+						      <&mpic 6>;
+				clocks = <&coreclk 2>, <&coreclk 5>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			cpurst at 20800 {
+				compatible = "marvell,armada-370-cpu-reset";
+				reg = <0x20800 0x10>;
+			};
+
+			pmsu at 22000 {
+				compatible = "marvell,armada-390-pmsu",
+					     "marvell,armada-380-pmsu";
+				reg = <0x22000 0x1000>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
+
+			/*
+			 * This port can be either x4 or x1. When
+			 * configured in x4 by the bootloader, then
+			 * pcie at 4,0 is not available.
+			 */
+			pcie at 1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie at 2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie at 3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			/*
+			 * x1 port only available when pcie at 1,0 is
+			 * configured as a x1 port
+			 */
+			pcie at 4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+		};
+	};
+};
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 10/10] Documentation: arm: update supported Marvell EBU processors
  2015-02-06 15:57 ` Thomas Petazzoni
@ 2015-02-06 15:57     ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
	Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij
  Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linux-gpio-u79uwXL29TY76Z2rM5mHXA, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard, Thomas Petazzoni

Now that we support Armada 39x, let's add this family of SoC to the
Marvell documentation, and a reference to a link with more details
about those processors. Unfortunately, no datasheet is publicly
available at this time.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 Documentation/arm/Marvell/README | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/arm/Marvell/README b/Documentation/arm/Marvell/README
index 1745379..18a775d 100644
--- a/Documentation/arm/Marvell/README
+++ b/Documentation/arm/Marvell/README
@@ -96,6 +96,11 @@ EBU Armada family
 	88F6820
 	88F6828
 
+  Armada 390/398 Flavors:
+	88F6920
+	88F6928
+    Product infos: http://www.marvell.com/embedded-processors/armada-39x/
+
   Armada XP Flavors:
         MV78230
         MV78260
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* [PATCH 10/10] Documentation: arm: update supported Marvell EBU processors
@ 2015-02-06 15:57     ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-06 15:57 UTC (permalink / raw)
  To: linux-arm-kernel

Now that we support Armada 39x, let's add this family of SoC to the
Marvell documentation, and a reference to a link with more details
about those processors. Unfortunately, no datasheet is publicly
available at this time.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
 Documentation/arm/Marvell/README | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/arm/Marvell/README b/Documentation/arm/Marvell/README
index 1745379..18a775d 100644
--- a/Documentation/arm/Marvell/README
+++ b/Documentation/arm/Marvell/README
@@ -96,6 +96,11 @@ EBU Armada family
 	88F6820
 	88F6828
 
+  Armada 390/398 Flavors:
+	88F6920
+	88F6928
+    Product infos: http://www.marvell.com/embedded-processors/armada-39x/
+
   Armada XP Flavors:
         MV78230
         MV78260
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 48+ messages in thread
* Re: [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
  2015-02-06 15:57   ` Thomas Petazzoni
@ 2015-02-06 17:05     ` Andrew Lunn
  -1 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-06 17:05 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Jason Cooper, Sebastian Hesselbarth, Gregory Clement, devicetree,
	Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij, linux-arm-kernel,
	linux-gpio, Tawfik Bayouk, Nadav Haklai, Lior Amsalem,
	Ezequiel Garcia, Maxime Ripard

On Fri, Feb 06, 2015 at 04:57:49PM +0100, Thomas Petazzoni wrote:
> This commit adds the Device Tree binding documentation to describe the
> pin-muxing controller of the Marvell Armada 39x processors. Two
> variants are supported for the moment: the 88F6920 (Armada 390) and
> 88F6928 (Armada 398).
> 
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>  .../pinctrl/marvell,armada-39x-pinctrl.txt         | 78 ++++++++++++++++++++++
>  1 file changed, 78 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
> new file mode 100644
> index 0000000..5b1a9dc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
> @@ -0,0 +1,78 @@
> +* Marvell Armada 39x SoC pinctrl driver for mpp
> +
> +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
> +part and usage.
> +
> +Required properties:
> +- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl"
> +  depending on the specific variant of the SoC being used.
> +- reg: register specifier of MPP registers
> +
> +Available mpp pins/groups and functions:
> +Note: brackets (x) are not part of the mpp name for marvell,function and given
> +only for more detailed description in this document.
> +
> +name    pins    functions
> +================================================================================
> +mpp0	0	gpio, ua0(rxd)
> +mpp1	1	gpio, ua0(txd)
> +mpp2	2	gpio, i2c0(sck)
> +mpp3	3	gpio, i2c0(sda)
> +mpp4	4	gpio, ua1(txd), ua0(rts), smi(mdc)
> +mpp5	5	gpio, ua1(rxd), ua0(cts), smi(mdio)
> +mpp6	6	gpio, dev(cs3), xsmi(mdio)
> +mpp7	7	gpio, dev(ad9), xsmi(mdc)
> +mpp8	8	gpio, dev(ad10), ptp(trig)
> +mpp9	9	gpio, dev(ad11), ptp(clk)

Hi Thomas

I wondering if there should be an explanation for the less common
names here. I'm guessing dev is a device bus of some sort? What is
xsmi? Some sort of extended System Management Interface? And m?

Thanks
	Andrewy

> +mpp10	10	gpio, dev(ad12), ptp(event)
> +mpp11	11	gpio, dev(ad13), led(clk)
> +mpp12	12	gpio, pcie0(rstout), dev(ad14), led(stb)
> +mpp13	13	gpio, dev(ad15), led(data)
> +mpp14	14	gpio, m(vtt), dev(wen1), ua1(txd)
> +mpp15	15	gpio, pcie0(rstout), spi0(mosi), i2c1(sck)
> +mpp16	16	gpio, m(decc), spi0(miso), i2c1(sda)
> +mpp17	17	gpio, ua1(rxd), spi0(sck), smi(mdio)
> +mpp18	18	gpio, ua1(txd), spi0(cs0), i2c2(sck)
> +mpp19	19	gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda)
> +mpp20	20	gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc)
> +mpp21	21	gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0)
> +mpp22	22	gpio, spi0(mosi), dev(ad0)
> +mpp23	23	gpio, spi0(sck), dev(ad2)
> +mpp24	24	gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
> +mpp25	25	gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0)
> +mpp26	26	gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1)
> +mpp27	27	gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout)
> +mpp28	28	gpio, sd(clk), dev(ad5), ge(txd0)
> +mpp29	29	gpio, dev(ale0), ge(txd1)
> +mpp30	30	gpio, dev(oen), ge(txd2)
> +mpp31	31	gpio, dev(ale1), ge(txd3)
> +mpp32	32	gpio, dev(wen0), ge(txctl)
> +mpp33	33	gpio, m(decc), dev(ad3)
> +mpp34	34	gpio, dev(ad1)
> +mpp35	35	gpio, ref(clk), dev(a1)
> +mpp36	36	gpio, dev(a0)
> +mpp37	37	gpio, sd(d3), dev(ad8), ge(rxclk)
> +mpp38	38	gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1)
> +mpp39	39	gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2)
> +mpp40	40	gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3)
> +mpp41	41	gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl)
> +mpp42	42	gpio, ua1(txd), ua0(rts), dev(ad7)
> +mpp43	43	gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1)
> +mpp44	44	gpio, sata0(present) [1], sata1(present) [1], led(clk)
> +mpp45	45	gpio, ref(clk), pcie0(rstout), ua1(rxd)
> +mpp46	46	gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb)
> +mpp47	47	gpio, sata0(present) [1], sata1(present) [1], led(data)
> +mpp48	48	gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd)
> +mpp49	49	gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd)
> +mpp50	50	gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd)
> +mpp51	51	gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd)
> +mpp52	52	gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck)
> +mpp53	53	gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda)
> +mpp54	54	gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd)
> +mpp55	55	gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd)
> +mpp56	56	gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd)
> +mpp57	57	gpio, spi1(sck), sd(clk), ua1(txd)
> +mpp58	58	gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
> +mpp59	59	gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2)
> +
> +[1]: only available on 88F6928
> -- 
> 2.1.0
> 

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
@ 2015-02-06 17:05     ` Andrew Lunn
  0 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-06 17:05 UTC (permalink / raw)
  To: linux-arm-kernel

On Fri, Feb 06, 2015 at 04:57:49PM +0100, Thomas Petazzoni wrote:
> This commit adds the Device Tree binding documentation to describe the
> pin-muxing controller of the Marvell Armada 39x processors. Two
> variants are supported for the moment: the 88F6920 (Armada 390) and
> 88F6928 (Armada 398).
> 
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>  .../pinctrl/marvell,armada-39x-pinctrl.txt         | 78 ++++++++++++++++++++++
>  1 file changed, 78 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
> new file mode 100644
> index 0000000..5b1a9dc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
> @@ -0,0 +1,78 @@
> +* Marvell Armada 39x SoC pinctrl driver for mpp
> +
> +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
> +part and usage.
> +
> +Required properties:
> +- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl"
> +  depending on the specific variant of the SoC being used.
> +- reg: register specifier of MPP registers
> +
> +Available mpp pins/groups and functions:
> +Note: brackets (x) are not part of the mpp name for marvell,function and given
> +only for more detailed description in this document.
> +
> +name    pins    functions
> +================================================================================
> +mpp0	0	gpio, ua0(rxd)
> +mpp1	1	gpio, ua0(txd)
> +mpp2	2	gpio, i2c0(sck)
> +mpp3	3	gpio, i2c0(sda)
> +mpp4	4	gpio, ua1(txd), ua0(rts), smi(mdc)
> +mpp5	5	gpio, ua1(rxd), ua0(cts), smi(mdio)
> +mpp6	6	gpio, dev(cs3), xsmi(mdio)
> +mpp7	7	gpio, dev(ad9), xsmi(mdc)
> +mpp8	8	gpio, dev(ad10), ptp(trig)
> +mpp9	9	gpio, dev(ad11), ptp(clk)

Hi Thomas

I wondering if there should be an explanation for the less common
names here. I'm guessing dev is a device bus of some sort? What is
xsmi? Some sort of extended System Management Interface? And m?

Thanks
	Andrewy

> +mpp10	10	gpio, dev(ad12), ptp(event)
> +mpp11	11	gpio, dev(ad13), led(clk)
> +mpp12	12	gpio, pcie0(rstout), dev(ad14), led(stb)
> +mpp13	13	gpio, dev(ad15), led(data)
> +mpp14	14	gpio, m(vtt), dev(wen1), ua1(txd)
> +mpp15	15	gpio, pcie0(rstout), spi0(mosi), i2c1(sck)
> +mpp16	16	gpio, m(decc), spi0(miso), i2c1(sda)
> +mpp17	17	gpio, ua1(rxd), spi0(sck), smi(mdio)
> +mpp18	18	gpio, ua1(txd), spi0(cs0), i2c2(sck)
> +mpp19	19	gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda)
> +mpp20	20	gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc)
> +mpp21	21	gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0)
> +mpp22	22	gpio, spi0(mosi), dev(ad0)
> +mpp23	23	gpio, spi0(sck), dev(ad2)
> +mpp24	24	gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
> +mpp25	25	gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0)
> +mpp26	26	gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1)
> +mpp27	27	gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout)
> +mpp28	28	gpio, sd(clk), dev(ad5), ge(txd0)
> +mpp29	29	gpio, dev(ale0), ge(txd1)
> +mpp30	30	gpio, dev(oen), ge(txd2)
> +mpp31	31	gpio, dev(ale1), ge(txd3)
> +mpp32	32	gpio, dev(wen0), ge(txctl)
> +mpp33	33	gpio, m(decc), dev(ad3)
> +mpp34	34	gpio, dev(ad1)
> +mpp35	35	gpio, ref(clk), dev(a1)
> +mpp36	36	gpio, dev(a0)
> +mpp37	37	gpio, sd(d3), dev(ad8), ge(rxclk)
> +mpp38	38	gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1)
> +mpp39	39	gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2)
> +mpp40	40	gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3)
> +mpp41	41	gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl)
> +mpp42	42	gpio, ua1(txd), ua0(rts), dev(ad7)
> +mpp43	43	gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1)
> +mpp44	44	gpio, sata0(present) [1], sata1(present) [1], led(clk)
> +mpp45	45	gpio, ref(clk), pcie0(rstout), ua1(rxd)
> +mpp46	46	gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb)
> +mpp47	47	gpio, sata0(present) [1], sata1(present) [1], led(data)
> +mpp48	48	gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd)
> +mpp49	49	gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd)
> +mpp50	50	gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd)
> +mpp51	51	gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd)
> +mpp52	52	gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck)
> +mpp53	53	gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda)
> +mpp54	54	gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd)
> +mpp55	55	gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd)
> +mpp56	56	gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd)
> +mpp57	57	gpio, spi1(sck), sd(clk), ua1(txd)
> +mpp58	58	gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
> +mpp59	59	gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2)
> +
> +[1]: only available on 88F6928
> -- 
> 2.1.0
> 

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  2015-02-06 15:57     ` Thomas Petazzoni
@ 2015-02-06 17:21       ` Andrew Lunn
  -1 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-06 17:21 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Jason Cooper, Sebastian Hesselbarth, Gregory Clement, devicetree,
	Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij, linux-arm-kernel,
	linux-gpio, Tawfik Bayouk, Nadav Haklai, Lior Amsalem,
	Ezequiel Garcia, Maxime Ripard

On Fri, Feb 06, 2015 at 04:57:55PM +0100, Thomas Petazzoni wrote:
> This commit adds the Device Tree files for the Armada 39x family of
> processors, as well as one Armada 398 Development Board.
> 
> Like for other Marvell EBU families, a common armada-39x.dtsi contains
> the description of the common features of all Armada 39x SoCs, while
> armada-390.dtsi and armada-398.dtsi respectively describe the
> specificities of those SoCs.
> 
> Finally, an armada-398-db.dts file is added to describe the Armada 398
> Development Board itself.
> 
> So far, the following features are supported:
> 
>  * SMP: dual Cortex-A9
>  * Basic ARM IPs: SCU, timer, GIC
>  * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
>    controller, MPIC interrupt controller, timer, CPU reset for SMP,
>    PMSU.
>  * I2C
>  * UART
>  * PCIe
> 
> Additional features will be supported in the future.
> 
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>  arch/arm/boot/dts/Makefile          |   2 +
>  arch/arm/boot/dts/armada-390.dtsi   |  57 ++++++
>  arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++
>  arch/arm/boot/dts/armada-398.dtsi   |  60 ++++++
>  arch/arm/boot/dts/armada-39x.dtsi   | 372 ++++++++++++++++++++++++++++++++++++
>  5 files changed, 607 insertions(+)
>  create mode 100644 arch/arm/boot/dts/armada-390.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-398-db.dts
>  create mode 100644 arch/arm/boot/dts/armada-398.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 968bc7a..64886fb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
>  	armada-388-db.dtb \
>  	armada-388-gp.dtb \
>  	armada-388-rd.dtb
> +dtb-$(CONFIG_MACH_ARMADA_39X) += \
> +	armada-398-db.dtb
>  dtb-$(CONFIG_MACH_ARMADA_XP) += \
>  	armada-xp-axpwifiap.dtb \
>  	armada-xp-db.dtb \
> diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi
> new file mode 100644
> index 0000000..094e39c
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-390.dtsi
> @@ -0,0 +1,57 @@
> +/*
> + * Device Tree Include file for Marvell Armada 390 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	soc {
> +		internal-regs {
> +			pinctrl@18000 {
> +				compatible = "marvell,mv88f6920-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +};
> diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
> new file mode 100644
> index 0000000..b889864
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398-db.dts
> @@ -0,0 +1,116 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 Development Board
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "armada-398.dtsi"
> +
> +/ {
> +	model = "Marvell Armada 398 Development Board";
> +	compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200 earlyprintk";
> +	};
> +

Arnd has been encouraging people not use earlyprintk here.  Also a
stdout-path would be nice. We also seem to be missing aliases for the
serial ports.

> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000>; /* 2 GB */
> +	};
> +
> +	soc {
> +		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> +			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
> +
> +		internal-regs {
> +                        i2c@11000 {
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-names = "default";
> +                                status = "okay";
> +                                clock-frequency = <100000>;
> +                        };
> +
> +			serial@12000 {
> +				pinctrl-0 = <&uart0_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +

Tab vs space issue here somewhere? Probably the i2c node.

> +			serial@12100 {
> +				pinctrl-0 = <&uart1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			pinctrl@18000 {
> +				uart0_pins: uart0-pins {
> +					marvell,pins = "mpp0", "mpp1";
> +					marvell,function = "ua0";
> +				};
> +
> +				uart1_pins: uart1-pins {
> +					marvell,pins = "mpp19", "mpp20";
> +					marvell,function = "ua1";
> +				};

Does it make sense to put there in the .dtsi file? I know there are
other choices, but generally board manufacturers tend to follow the
reference design.

	  Andrew

> +			};
> +		};
> +
> +		pcie-controller {
> +			status = "okay";
> +
> +			pcie@1,0 {
> +				status = "okay";
> +			};
> +
> +			pcie@2,0 {
> +				status = "okay";
> +			};
> +
> +			pcie@3,0 {
> +				status = "okay";
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi
> new file mode 100644
> index 0000000..fdc2591
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398.dtsi
> @@ -0,0 +1,60 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	compatible = "marvell,armada398", "marvell,armada390";
> +
> +	soc {
> +		internal-regs {
> +			pinctrl@18000 {
> +				compatible = "marvell,mv88f6928-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
> new file mode 100644
> index 0000000..e248332
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-39x.dtsi
> @@ -0,0 +1,372 @@
> +/*
> + * Device Tree Include file for Marvell Armada 39x family of SoCs.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
> +
> +/ {
> +	model = "Marvell Armada 39x family SoC";
> +	compatible = "marvell,armada390";
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "marvell,armada-390-smp";
> +
> +		cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <0>;
> +		};
> +		cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <1>;
> +		};
> +	};
> +
> +	soc {
> +		compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus",
> +			     "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		controller = <&mbusc>;
> +		interrupt-parent = <&gic>;
> +		pcie-mem-aperture = <0xe0000000 0x8000000>;
> +		pcie-io-aperture  = <0xe8000000 0x100000>;
> +
> +		bootrom {
> +			compatible = "marvell,bootrom";
> +			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
> +		};
> +
> +		internal-regs {
> +			compatible = "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
> +
> +			scu@c000 {
> +				compatible = "arm,cortex-a9-scu";
> +				reg = <0xc000 0x100>;
> +			};
> +
> +			timer@c600 {
> +				compatible = "arm,cortex-a9-twd-timer";
> +				reg = <0xc600 0x20>;
> +				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
> +				clocks = <&coreclk 2>;
> +			};
> +
> +			gic: interrupt-controller@d000 {
> +				compatible = "arm,cortex-a9-gic";
> +				#interrupt-cells = <3>;
> +				#size-cells = <0>;
> +				interrupt-controller;
> +				reg = <0xd000 0x1000>,
> +				      <0xc100 0x100>;
> +			};
> +
> +			i2c0: i2c@11000 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11000 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c@11100 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11100 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c2: i2c@11200 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11200 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c3: i2c@11300 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11300 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12000 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12000 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12100 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12100 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12200 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12200 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12300 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12300 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			pinctrl@18000 {
> +				i2c0_pins: i2c0-pins {
> +					marvell,pins = "mpp2", "mpp3";
> +					marvell,function = "i2c0";
> +				};
> +			};
> +
> +			system-controller@18200 {
> +				compatible = "marvell,armada-390-system-controller",
> +					     "marvell,armada-370-xp-system-controller";
> +				reg = <0x18200 0x100>;
> +			};
> +
> +			gateclk: clock-gating-control@18220 {
> +				compatible = "marvell,armada-390-gating-clock";
> +				reg = <0x18220 0x4>;
> +				clocks = <&coreclk 0>;
> +				#clock-cells = <1>;
> +			};
> +
> +			coreclk: mvebu-sar@18600 {
> +				compatible = "marvell,armada-390-core-clock";
> +				reg = <0x18600 0x04>;
> +				#clock-cells = <1>;
> +			};
> +
> +			mbusc: mbus-controller@20000 {
> +				compatible = "marvell,mbus-controller";
> +				reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>;
> +			};
> +
> +			mpic: interrupt-controller@20000 {
> +				compatible = "marvell,mpic";
> +				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
> +				#interrupt-cells = <1>;
> +				#size-cells = <1>;
> +				interrupt-controller;
> +				msi-controller;
> +				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			timer@20300 {
> +				compatible = "marvell,armada-380-timer",
> +					     "marvell,armada-xp-timer";
> +				reg = <0x20300 0x30>, <0x21040 0x30>;
> +				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&mpic 5>,
> +						      <&mpic 6>;
> +				clocks = <&coreclk 2>, <&coreclk 5>;
> +				clock-names = "nbclk", "fixed";
> +			};
> +
> +			cpurst@20800 {
> +				compatible = "marvell,armada-370-cpu-reset";
> +				reg = <0x20800 0x10>;
> +			};
> +
> +			pmsu@22000 {
> +				compatible = "marvell,armada-390-pmsu",
> +					     "marvell,armada-380-pmsu";
> +				reg = <0x22000 0x1000>;
> +			};
> +		};
> +
> +		pcie-controller {
> +			compatible = "marvell,armada-370-pcie";
> +			status = "disabled";
> +			device_type = "pci";
> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			msi-parent = <&mpic>;
> +			bus-range = <0x00 0xff>;
> +
> +			ranges =
> +			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
> +				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
> +				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
> +				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
> +				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
> +				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
> +				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
> +				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
> +				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
> +				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
> +				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
> +				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
> +
> +			/*
> +			 * This port can be either x4 or x1. When
> +			 * configured in x4 by the bootloader, then
> +			 * pcie@4,0 is not available.
> +			 */
> +			pcie@1,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
> +				reg = <0x0800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
> +					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <0>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 8>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie@2,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
> +				reg = <0x1000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
> +					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <1>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 5>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie@3,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
> +				reg = <0x1800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
> +					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <2>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 6>;
> +				status = "disabled";
> +			};
> +
> +			/*
> +			 * x1 port only available when pcie@1,0 is
> +			 * configured as a x1 port
> +			 */
> +			pcie@4,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
> +				reg = <0x2000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
> +					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <3>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 7>;
> +				status = "disabled";
> +			};
> +		};
> +	};
> +};
> -- 
> 2.1.0
> 

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
@ 2015-02-06 17:21       ` Andrew Lunn
  0 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-06 17:21 UTC (permalink / raw)
  To: linux-arm-kernel

On Fri, Feb 06, 2015 at 04:57:55PM +0100, Thomas Petazzoni wrote:
> This commit adds the Device Tree files for the Armada 39x family of
> processors, as well as one Armada 398 Development Board.
> 
> Like for other Marvell EBU families, a common armada-39x.dtsi contains
> the description of the common features of all Armada 39x SoCs, while
> armada-390.dtsi and armada-398.dtsi respectively describe the
> specificities of those SoCs.
> 
> Finally, an armada-398-db.dts file is added to describe the Armada 398
> Development Board itself.
> 
> So far, the following features are supported:
> 
>  * SMP: dual Cortex-A9
>  * Basic ARM IPs: SCU, timer, GIC
>  * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
>    controller, MPIC interrupt controller, timer, CPU reset for SMP,
>    PMSU.
>  * I2C
>  * UART
>  * PCIe
> 
> Additional features will be supported in the future.
> 
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>  arch/arm/boot/dts/Makefile          |   2 +
>  arch/arm/boot/dts/armada-390.dtsi   |  57 ++++++
>  arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++
>  arch/arm/boot/dts/armada-398.dtsi   |  60 ++++++
>  arch/arm/boot/dts/armada-39x.dtsi   | 372 ++++++++++++++++++++++++++++++++++++
>  5 files changed, 607 insertions(+)
>  create mode 100644 arch/arm/boot/dts/armada-390.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-398-db.dts
>  create mode 100644 arch/arm/boot/dts/armada-398.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 968bc7a..64886fb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
>  	armada-388-db.dtb \
>  	armada-388-gp.dtb \
>  	armada-388-rd.dtb
> +dtb-$(CONFIG_MACH_ARMADA_39X) += \
> +	armada-398-db.dtb
>  dtb-$(CONFIG_MACH_ARMADA_XP) += \
>  	armada-xp-axpwifiap.dtb \
>  	armada-xp-db.dtb \
> diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi
> new file mode 100644
> index 0000000..094e39c
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-390.dtsi
> @@ -0,0 +1,57 @@
> +/*
> + * Device Tree Include file for Marvell Armada 390 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	soc {
> +		internal-regs {
> +			pinctrl at 18000 {
> +				compatible = "marvell,mv88f6920-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +};
> diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
> new file mode 100644
> index 0000000..b889864
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398-db.dts
> @@ -0,0 +1,116 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 Development Board
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "armada-398.dtsi"
> +
> +/ {
> +	model = "Marvell Armada 398 Development Board";
> +	compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200 earlyprintk";
> +	};
> +

Arnd has been encouraging people not use earlyprintk here.  Also a
stdout-path would be nice. We also seem to be missing aliases for the
serial ports.

> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000>; /* 2 GB */
> +	};
> +
> +	soc {
> +		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> +			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
> +
> +		internal-regs {
> +                        i2c at 11000 {
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-names = "default";
> +                                status = "okay";
> +                                clock-frequency = <100000>;
> +                        };
> +
> +			serial at 12000 {
> +				pinctrl-0 = <&uart0_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +

Tab vs space issue here somewhere? Probably the i2c node.

> +			serial at 12100 {
> +				pinctrl-0 = <&uart1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			pinctrl at 18000 {
> +				uart0_pins: uart0-pins {
> +					marvell,pins = "mpp0", "mpp1";
> +					marvell,function = "ua0";
> +				};
> +
> +				uart1_pins: uart1-pins {
> +					marvell,pins = "mpp19", "mpp20";
> +					marvell,function = "ua1";
> +				};

Does it make sense to put there in the .dtsi file? I know there are
other choices, but generally board manufacturers tend to follow the
reference design.

	  Andrew

> +			};
> +		};
> +
> +		pcie-controller {
> +			status = "okay";
> +
> +			pcie at 1,0 {
> +				status = "okay";
> +			};
> +
> +			pcie at 2,0 {
> +				status = "okay";
> +			};
> +
> +			pcie at 3,0 {
> +				status = "okay";
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi
> new file mode 100644
> index 0000000..fdc2591
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398.dtsi
> @@ -0,0 +1,60 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	compatible = "marvell,armada398", "marvell,armada390";
> +
> +	soc {
> +		internal-regs {
> +			pinctrl at 18000 {
> +				compatible = "marvell,mv88f6928-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
> new file mode 100644
> index 0000000..e248332
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-39x.dtsi
> @@ -0,0 +1,372 @@
> +/*
> + * Device Tree Include file for Marvell Armada 39x family of SoCs.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
> +
> +/ {
> +	model = "Marvell Armada 39x family SoC";
> +	compatible = "marvell,armada390";
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "marvell,armada-390-smp";
> +
> +		cpu at 0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <0>;
> +		};
> +		cpu at 1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <1>;
> +		};
> +	};
> +
> +	soc {
> +		compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus",
> +			     "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		controller = <&mbusc>;
> +		interrupt-parent = <&gic>;
> +		pcie-mem-aperture = <0xe0000000 0x8000000>;
> +		pcie-io-aperture  = <0xe8000000 0x100000>;
> +
> +		bootrom {
> +			compatible = "marvell,bootrom";
> +			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
> +		};
> +
> +		internal-regs {
> +			compatible = "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
> +
> +			scu at c000 {
> +				compatible = "arm,cortex-a9-scu";
> +				reg = <0xc000 0x100>;
> +			};
> +
> +			timer at c600 {
> +				compatible = "arm,cortex-a9-twd-timer";
> +				reg = <0xc600 0x20>;
> +				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
> +				clocks = <&coreclk 2>;
> +			};
> +
> +			gic: interrupt-controller at d000 {
> +				compatible = "arm,cortex-a9-gic";
> +				#interrupt-cells = <3>;
> +				#size-cells = <0>;
> +				interrupt-controller;
> +				reg = <0xd000 0x1000>,
> +				      <0xc100 0x100>;
> +			};
> +
> +			i2c0: i2c at 11000 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11000 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c at 11100 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11100 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c2: i2c at 11200 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11200 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c3: i2c at 11300 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11300 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12000 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12000 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12100 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12100 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12200 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12200 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12300 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12300 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			pinctrl at 18000 {
> +				i2c0_pins: i2c0-pins {
> +					marvell,pins = "mpp2", "mpp3";
> +					marvell,function = "i2c0";
> +				};
> +			};
> +
> +			system-controller at 18200 {
> +				compatible = "marvell,armada-390-system-controller",
> +					     "marvell,armada-370-xp-system-controller";
> +				reg = <0x18200 0x100>;
> +			};
> +
> +			gateclk: clock-gating-control at 18220 {
> +				compatible = "marvell,armada-390-gating-clock";
> +				reg = <0x18220 0x4>;
> +				clocks = <&coreclk 0>;
> +				#clock-cells = <1>;
> +			};
> +
> +			coreclk: mvebu-sar at 18600 {
> +				compatible = "marvell,armada-390-core-clock";
> +				reg = <0x18600 0x04>;
> +				#clock-cells = <1>;
> +			};
> +
> +			mbusc: mbus-controller at 20000 {
> +				compatible = "marvell,mbus-controller";
> +				reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>;
> +			};
> +
> +			mpic: interrupt-controller at 20000 {
> +				compatible = "marvell,mpic";
> +				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
> +				#interrupt-cells = <1>;
> +				#size-cells = <1>;
> +				interrupt-controller;
> +				msi-controller;
> +				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			timer at 20300 {
> +				compatible = "marvell,armada-380-timer",
> +					     "marvell,armada-xp-timer";
> +				reg = <0x20300 0x30>, <0x21040 0x30>;
> +				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&mpic 5>,
> +						      <&mpic 6>;
> +				clocks = <&coreclk 2>, <&coreclk 5>;
> +				clock-names = "nbclk", "fixed";
> +			};
> +
> +			cpurst at 20800 {
> +				compatible = "marvell,armada-370-cpu-reset";
> +				reg = <0x20800 0x10>;
> +			};
> +
> +			pmsu at 22000 {
> +				compatible = "marvell,armada-390-pmsu",
> +					     "marvell,armada-380-pmsu";
> +				reg = <0x22000 0x1000>;
> +			};
> +		};
> +
> +		pcie-controller {
> +			compatible = "marvell,armada-370-pcie";
> +			status = "disabled";
> +			device_type = "pci";
> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			msi-parent = <&mpic>;
> +			bus-range = <0x00 0xff>;
> +
> +			ranges =
> +			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
> +				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
> +				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
> +				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
> +				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
> +				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
> +				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
> +				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
> +				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
> +				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
> +				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
> +				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
> +
> +			/*
> +			 * This port can be either x4 or x1. When
> +			 * configured in x4 by the bootloader, then
> +			 * pcie at 4,0 is not available.
> +			 */
> +			pcie at 1,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
> +				reg = <0x0800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
> +					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <0>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 8>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie at 2,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
> +				reg = <0x1000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
> +					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <1>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 5>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie at 3,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
> +				reg = <0x1800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
> +					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <2>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 6>;
> +				status = "disabled";
> +			};
> +
> +			/*
> +			 * x1 port only available when pcie at 1,0 is
> +			 * configured as a x1 port
> +			 */
> +			pcie at 4,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
> +				reg = <0x2000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
> +					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <3>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 7>;
> +				status = "disabled";
> +			};
> +		};
> +	};
> +};
> -- 
> 2.1.0
> 

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
  2015-02-06 15:57   ` Thomas Petazzoni
@ 2015-02-06 19:57     ` Stephen Boyd
  -1 siblings, 0 replies; 48+ messages in thread
From: Stephen Boyd @ 2015-02-06 19:57 UTC (permalink / raw)
  To: Thomas Petazzoni, Jason Cooper, Andrew Lunn,
	Sebastian Hesselbarth, Gregory Clement, devicetree, Rob Herring,
	Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Linus Walleij
  Cc: linux-arm-kernel, linux-gpio, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia, Maxime Ripard

On 02/06/15 07:57, Thomas Petazzoni wrote:
> diff --git a/arch/arm/mach-mvebu/board-v7.c b/arch/arm/mach-mvebu/board-v7.c
> index 89a139e..d88438f 100644
> --- a/arch/arm/mach-mvebu/board-v7.c
> +++ b/arch/arm/mach-mvebu/board-v7.c
> @@ -232,3 +232,17 @@ DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)")
>  	.restart	= mvebu_restart,
>  	.dt_compat	= armada_38x_dt_compat,
>  MACHINE_END
> +
> +static const char * const armada_39x_dt_compat[] = {

 __initconst?

> +	"marvell,armada390",
> +	"marvell,armada398",
> +	NULL,
> +};
> +
> +DT_MACHINE_START(ARMADA_39X_DT, "Marvell Armada 39x (Device Tree)")
> +	.l2c_aux_val	= 0,
> +	.l2c_aux_mask	= ~0,
> +	.init_irq       = mvebu_init_irq,
> +	.restart	= mvebu_restart,
> +	.dt_compat	= armada_39x_dt_compat,
> +MACHINE_END
>

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
@ 2015-02-06 19:57     ` Stephen Boyd
  0 siblings, 0 replies; 48+ messages in thread
From: Stephen Boyd @ 2015-02-06 19:57 UTC (permalink / raw)
  To: linux-arm-kernel

On 02/06/15 07:57, Thomas Petazzoni wrote:
> diff --git a/arch/arm/mach-mvebu/board-v7.c b/arch/arm/mach-mvebu/board-v7.c
> index 89a139e..d88438f 100644
> --- a/arch/arm/mach-mvebu/board-v7.c
> +++ b/arch/arm/mach-mvebu/board-v7.c
> @@ -232,3 +232,17 @@ DT_MACHINE_START(ARMADA_38X_DT, "Marvell Armada 380/385 (Device Tree)")
>  	.restart	= mvebu_restart,
>  	.dt_compat	= armada_38x_dt_compat,
>  MACHINE_END
> +
> +static const char * const armada_39x_dt_compat[] = {

 __initconst?

> +	"marvell,armada390",
> +	"marvell,armada398",
> +	NULL,
> +};
> +
> +DT_MACHINE_START(ARMADA_39X_DT, "Marvell Armada 39x (Device Tree)")
> +	.l2c_aux_val	= 0,
> +	.l2c_aux_mask	= ~0,
> +	.init_irq       = mvebu_init_irq,
> +	.restart	= mvebu_restart,
> +	.dt_compat	= armada_39x_dt_compat,
> +MACHINE_END
>

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
  2015-02-06 15:57   ` Thomas Petazzoni
@ 2015-02-06 20:31       ` Maxime Ripard
  -1 siblings, 0 replies; 48+ messages in thread
From: Maxime Ripard @ 2015-02-06 20:31 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring,
	Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
	Mike Turquette, Stephen Boyd, Linus Walleij,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	linux-gpio-u79uwXL29TY76Z2rM5mHXA, Tawfik Bayouk, Nadav Haklai,
	Lior Amsalem, Ezequiel Garcia

[-- Attachment #1: Type: text/plain, Size: 1291 bytes --]

Hi Thomas,

On Fri, Feb 06, 2015 at 04:57:54PM +0100, Thomas Petazzoni wrote:
> This commit adds the core support for Armada 39x, which is quite
> simple:
> 
>  - a new Kconfig option which selects the appropriate clock and
>    pinctrl drivers as well as other common features (GIC, L2 cache,
>    SMP, etc.)
> 
>  - a new DT_MACHINE_START which references the top-level compatible
>    strings supported for the Marvell Armada 39x.
> 
>  - a new SMP enable-method. The mechanism to enable CPUs for Armada
>    39x appears to be the same as Armada 38x. However, we do want to

                                                              ^ not?

>    use marvell,armada-380-smp in the Device Tree, in the case of the
>    discovery of a subtle difference in the future, which would require
>    changing the Device Tree. And the enable-method isn't a compatible
>    string: you can't specify several values and expect a fallback on
>    the second string if the first one isn't supported. Therefore, we
>    simply declare the SMP enable method "marvell,armada-390-smp" as
>    doing the same thing as the "marvell,armada-380-smp" one.
> 

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
@ 2015-02-06 20:31       ` Maxime Ripard
  0 siblings, 0 replies; 48+ messages in thread
From: Maxime Ripard @ 2015-02-06 20:31 UTC (permalink / raw)
  To: linux-arm-kernel

Hi Thomas,

On Fri, Feb 06, 2015 at 04:57:54PM +0100, Thomas Petazzoni wrote:
> This commit adds the core support for Armada 39x, which is quite
> simple:
> 
>  - a new Kconfig option which selects the appropriate clock and
>    pinctrl drivers as well as other common features (GIC, L2 cache,
>    SMP, etc.)
> 
>  - a new DT_MACHINE_START which references the top-level compatible
>    strings supported for the Marvell Armada 39x.
> 
>  - a new SMP enable-method. The mechanism to enable CPUs for Armada
>    39x appears to be the same as Armada 38x. However, we do want to

                                                              ^ not?

>    use marvell,armada-380-smp in the Device Tree, in the case of the
>    discovery of a subtle difference in the future, which would require
>    changing the Device Tree. And the enable-method isn't a compatible
>    string: you can't specify several values and expect a fallback on
>    the second string if the first one isn't supported. Therefore, we
>    simply declare the SMP enable method "marvell,armada-390-smp" as
>    doing the same thing as the "marvell,armada-380-smp" one.
> 

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150206/562eab45/attachment.sig>

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  2015-02-06 15:57     ` Thomas Petazzoni
@ 2015-02-06 20:39       ` Maxime Ripard
  -1 siblings, 0 replies; 48+ messages in thread
From: Maxime Ripard @ 2015-02-06 20:39 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, Linus Walleij, linux-arm-kernel, linux-gpio,
	Tawfik Bayouk, Nadav Haklai, Lior Amsalem, Ezequiel Garcia

[-- Attachment #1: Type: text/plain, Size: 24684 bytes --]

On Fri, Feb 06, 2015 at 04:57:55PM +0100, Thomas Petazzoni wrote:
> This commit adds the Device Tree files for the Armada 39x family of
> processors, as well as one Armada 398 Development Board.
> 
> Like for other Marvell EBU families, a common armada-39x.dtsi contains
> the description of the common features of all Armada 39x SoCs, while
> armada-390.dtsi and armada-398.dtsi respectively describe the
> specificities of those SoCs.
> 
> Finally, an armada-398-db.dts file is added to describe the Armada 398
> Development Board itself.
> 
> So far, the following features are supported:
> 
>  * SMP: dual Cortex-A9
>  * Basic ARM IPs: SCU, timer, GIC
>  * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
>    controller, MPIC interrupt controller, timer, CPU reset for SMP,
>    PMSU.
>  * I2C
>  * UART
>  * PCIe
> 
> Additional features will be supported in the future.
> 
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>  arch/arm/boot/dts/Makefile          |   2 +
>  arch/arm/boot/dts/armada-390.dtsi   |  57 ++++++
>  arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++
>  arch/arm/boot/dts/armada-398.dtsi   |  60 ++++++
>  arch/arm/boot/dts/armada-39x.dtsi   | 372 ++++++++++++++++++++++++++++++++++++
>  5 files changed, 607 insertions(+)
>  create mode 100644 arch/arm/boot/dts/armada-390.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-398-db.dts
>  create mode 100644 arch/arm/boot/dts/armada-398.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 968bc7a..64886fb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
>  	armada-388-db.dtb \
>  	armada-388-gp.dtb \
>  	armada-388-rd.dtb
> +dtb-$(CONFIG_MACH_ARMADA_39X) += \
> +	armada-398-db.dtb
>  dtb-$(CONFIG_MACH_ARMADA_XP) += \
>  	armada-xp-axpwifiap.dtb \
>  	armada-xp-db.dtb \
> diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi
> new file mode 100644
> index 0000000..094e39c
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-390.dtsi
> @@ -0,0 +1,57 @@
> +/*
> + * Device Tree Include file for Marvell Armada 390 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	soc {
> +		internal-regs {
> +			pinctrl@18000 {
> +				compatible = "marvell,mv88f6920-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +};
> diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
> new file mode 100644
> index 0000000..b889864
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398-db.dts
> @@ -0,0 +1,116 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 Development Board
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "armada-398.dtsi"
> +
> +/ {
> +	model = "Marvell Armada 398 Development Board";
> +	compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200 earlyprintk";

I think Arnd wanted to remove all the earlyprintk here, just in case
the debug_ll options compiled in the kernel would not match the
board/SoC options.

> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000>; /* 2 GB */
> +	};
> +
> +	soc {
> +		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> +			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
> +
> +		internal-regs {
> +                        i2c@11000 {
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-names = "default";
> +                                status = "okay";
> +                                clock-frequency = <100000>;

The indentation looks off here.

It seems like you indented the two first lines with tabs, and the two
last with spaces.

> +                        };
> +
> +			serial@12000 {
> +				pinctrl-0 = <&uart0_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			serial@12100 {
> +				pinctrl-0 = <&uart1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			pinctrl@18000 {
> +				uart0_pins: uart0-pins {
> +					marvell,pins = "mpp0", "mpp1";
> +					marvell,function = "ua0";
> +				};
> +
> +				uart1_pins: uart1-pins {
> +					marvell,pins = "mpp19", "mpp20";
> +					marvell,function = "ua1";
> +				};

These two looks like generic muxing options, maybe they should be put
in the SoC DTSI?

> +			};
> +		};
> +
> +		pcie-controller {
> +			status = "okay";
> +
> +			pcie@1,0 {
> +				status = "okay";
> +			};
> +
> +			pcie@2,0 {
> +				status = "okay";
> +			};
> +
> +			pcie@3,0 {
> +				status = "okay";
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi
> new file mode 100644
> index 0000000..fdc2591
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398.dtsi
> @@ -0,0 +1,60 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	compatible = "marvell,armada398", "marvell,armada390";
> +
> +	soc {
> +		internal-regs {
> +			pinctrl@18000 {
> +				compatible = "marvell,mv88f6928-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
> new file mode 100644
> index 0000000..e248332
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-39x.dtsi
> @@ -0,0 +1,372 @@
> +/*
> + * Device Tree Include file for Marvell Armada 39x family of SoCs.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
> +
> +/ {
> +	model = "Marvell Armada 39x family SoC";
> +	compatible = "marvell,armada390";
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "marvell,armada-390-smp";
> +
> +		cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <0>;
> +		};
> +		cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <1>;
> +		};
> +	};
> +
> +	soc {
> +		compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus",
> +			     "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		controller = <&mbusc>;
> +		interrupt-parent = <&gic>;
> +		pcie-mem-aperture = <0xe0000000 0x8000000>;
> +		pcie-io-aperture  = <0xe8000000 0x100000>;
> +
> +		bootrom {
> +			compatible = "marvell,bootrom";
> +			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
> +		};
> +
> +		internal-regs {
> +			compatible = "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
> +
> +			scu@c000 {
> +				compatible = "arm,cortex-a9-scu";
> +				reg = <0xc000 0x100>;
> +			};
> +
> +			timer@c600 {
> +				compatible = "arm,cortex-a9-twd-timer";
> +				reg = <0xc600 0x20>;
> +				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
> +				clocks = <&coreclk 2>;
> +			};
> +
> +			gic: interrupt-controller@d000 {
> +				compatible = "arm,cortex-a9-gic";
> +				#interrupt-cells = <3>;
> +				#size-cells = <0>;
> +				interrupt-controller;
> +				reg = <0xd000 0x1000>,
> +				      <0xc100 0x100>;
> +			};
> +
> +			i2c0: i2c@11000 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11000 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c@11100 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11100 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c2: i2c@11200 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11200 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c3: i2c@11300 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11300 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12000 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12000 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12100 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12100 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12200 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12200 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial@12300 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12300 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			pinctrl@18000 {
> +				i2c0_pins: i2c0-pins {
> +					marvell,pins = "mpp2", "mpp3";
> +					marvell,function = "i2c0";
> +				};
> +			};
> +
> +			system-controller@18200 {
> +				compatible = "marvell,armada-390-system-controller",
> +					     "marvell,armada-370-xp-system-controller";
> +				reg = <0x18200 0x100>;
> +			};
> +
> +			gateclk: clock-gating-control@18220 {
> +				compatible = "marvell,armada-390-gating-clock";
> +				reg = <0x18220 0x4>;
> +				clocks = <&coreclk 0>;
> +				#clock-cells = <1>;
> +			};
> +
> +			coreclk: mvebu-sar@18600 {
> +				compatible = "marvell,armada-390-core-clock";
> +				reg = <0x18600 0x04>;
> +				#clock-cells = <1>;
> +			};
> +
> +			mbusc: mbus-controller@20000 {
> +				compatible = "marvell,mbus-controller";
> +				reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>;
> +			};
> +
> +			mpic: interrupt-controller@20000 {

The unit-address doesn't match the reg address.

> +				compatible = "marvell,mpic";
> +				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
> +				#interrupt-cells = <1>;
> +				#size-cells = <1>;
> +				interrupt-controller;
> +				msi-controller;
> +				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			timer@20300 {
> +				compatible = "marvell,armada-380-timer",
> +					     "marvell,armada-xp-timer";
> +				reg = <0x20300 0x30>, <0x21040 0x30>;
> +				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&mpic 5>,
> +						      <&mpic 6>;
> +				clocks = <&coreclk 2>, <&coreclk 5>;
> +				clock-names = "nbclk", "fixed";
> +			};
> +
> +			cpurst@20800 {
> +				compatible = "marvell,armada-370-cpu-reset";
> +				reg = <0x20800 0x10>;
> +			};
> +
> +			pmsu@22000 {
> +				compatible = "marvell,armada-390-pmsu",
> +					     "marvell,armada-380-pmsu";
> +				reg = <0x22000 0x1000>;
> +			};
> +		};
> +
> +		pcie-controller {
> +			compatible = "marvell,armada-370-pcie";
> +			status = "disabled";
> +			device_type = "pci";
> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			msi-parent = <&mpic>;
> +			bus-range = <0x00 0xff>;
> +
> +			ranges =
> +			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
> +				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
> +				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
> +				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
> +				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
> +				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
> +				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
> +				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
> +				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
> +				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
> +				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
> +				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
> +
> +			/*
> +			 * This port can be either x4 or x1. When
> +			 * configured in x4 by the bootloader, then
> +			 * pcie@4,0 is not available.
> +			 */
> +			pcie@1,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
> +				reg = <0x0800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
> +					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <0>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 8>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie@2,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
> +				reg = <0x1000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
> +					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <1>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 5>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie@3,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
> +				reg = <0x1800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
> +					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <2>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 6>;
> +				status = "disabled";
> +			};
> +
> +			/*
> +			 * x1 port only available when pcie@1,0 is
> +			 * configured as a x1 port
> +			 */
> +			pcie@4,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
> +				reg = <0x2000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
> +					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <3>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 7>;
> +				status = "disabled";
> +			};
> +		};
> +	};
> +};
> -- 
> 2.1.0
> 

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
@ 2015-02-06 20:39       ` Maxime Ripard
  0 siblings, 0 replies; 48+ messages in thread
From: Maxime Ripard @ 2015-02-06 20:39 UTC (permalink / raw)
  To: linux-arm-kernel

On Fri, Feb 06, 2015 at 04:57:55PM +0100, Thomas Petazzoni wrote:
> This commit adds the Device Tree files for the Armada 39x family of
> processors, as well as one Armada 398 Development Board.
> 
> Like for other Marvell EBU families, a common armada-39x.dtsi contains
> the description of the common features of all Armada 39x SoCs, while
> armada-390.dtsi and armada-398.dtsi respectively describe the
> specificities of those SoCs.
> 
> Finally, an armada-398-db.dts file is added to describe the Armada 398
> Development Board itself.
> 
> So far, the following features are supported:
> 
>  * SMP: dual Cortex-A9
>  * Basic ARM IPs: SCU, timer, GIC
>  * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
>    controller, MPIC interrupt controller, timer, CPU reset for SMP,
>    PMSU.
>  * I2C
>  * UART
>  * PCIe
> 
> Additional features will be supported in the future.
> 
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>  arch/arm/boot/dts/Makefile          |   2 +
>  arch/arm/boot/dts/armada-390.dtsi   |  57 ++++++
>  arch/arm/boot/dts/armada-398-db.dts | 116 +++++++++++
>  arch/arm/boot/dts/armada-398.dtsi   |  60 ++++++
>  arch/arm/boot/dts/armada-39x.dtsi   | 372 ++++++++++++++++++++++++++++++++++++
>  5 files changed, 607 insertions(+)
>  create mode 100644 arch/arm/boot/dts/armada-390.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-398-db.dts
>  create mode 100644 arch/arm/boot/dts/armada-398.dtsi
>  create mode 100644 arch/arm/boot/dts/armada-39x.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 968bc7a..64886fb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -540,6 +540,8 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
>  	armada-388-db.dtb \
>  	armada-388-gp.dtb \
>  	armada-388-rd.dtb
> +dtb-$(CONFIG_MACH_ARMADA_39X) += \
> +	armada-398-db.dtb
>  dtb-$(CONFIG_MACH_ARMADA_XP) += \
>  	armada-xp-axpwifiap.dtb \
>  	armada-xp-db.dtb \
> diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi
> new file mode 100644
> index 0000000..094e39c
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-390.dtsi
> @@ -0,0 +1,57 @@
> +/*
> + * Device Tree Include file for Marvell Armada 390 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	soc {
> +		internal-regs {
> +			pinctrl at 18000 {
> +				compatible = "marvell,mv88f6920-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +};
> diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
> new file mode 100644
> index 0000000..b889864
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398-db.dts
> @@ -0,0 +1,116 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 Development Board
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "armada-398.dtsi"
> +
> +/ {
> +	model = "Marvell Armada 398 Development Board";
> +	compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200 earlyprintk";

I think Arnd wanted to remove all the earlyprintk here, just in case
the debug_ll options compiled in the kernel would not match the
board/SoC options.

> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000>; /* 2 GB */
> +	};
> +
> +	soc {
> +		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> +			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
> +
> +		internal-regs {
> +                        i2c at 11000 {
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-names = "default";
> +                                status = "okay";
> +                                clock-frequency = <100000>;

The indentation looks off here.

It seems like you indented the two first lines with tabs, and the two
last with spaces.

> +                        };
> +
> +			serial at 12000 {
> +				pinctrl-0 = <&uart0_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			serial at 12100 {
> +				pinctrl-0 = <&uart1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			pinctrl at 18000 {
> +				uart0_pins: uart0-pins {
> +					marvell,pins = "mpp0", "mpp1";
> +					marvell,function = "ua0";
> +				};
> +
> +				uart1_pins: uart1-pins {
> +					marvell,pins = "mpp19", "mpp20";
> +					marvell,function = "ua1";
> +				};

These two looks like generic muxing options, maybe they should be put
in the SoC DTSI?

> +			};
> +		};
> +
> +		pcie-controller {
> +			status = "okay";
> +
> +			pcie at 1,0 {
> +				status = "okay";
> +			};
> +
> +			pcie at 2,0 {
> +				status = "okay";
> +			};
> +
> +			pcie at 3,0 {
> +				status = "okay";
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi
> new file mode 100644
> index 0000000..fdc2591
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-398.dtsi
> @@ -0,0 +1,60 @@
> +/*
> + * Device Tree Include file for Marvell Armada 398 SoC.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "armada-39x.dtsi"
> +
> +/ {
> +	compatible = "marvell,armada398", "marvell,armada390";
> +
> +	soc {
> +		internal-regs {
> +			pinctrl at 18000 {
> +				compatible = "marvell,mv88f6928-pinctrl";
> +				reg = <0x18000 0x20>;
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
> new file mode 100644
> index 0000000..e248332
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-39x.dtsi
> @@ -0,0 +1,372 @@
> +/*
> + * Device Tree Include file for Marvell Armada 39x family of SoCs.
> + *
> + * Copyright (C) 2015 Marvell
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
> +
> +/ {
> +	model = "Marvell Armada 39x family SoC";
> +	compatible = "marvell,armada390";
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "marvell,armada-390-smp";
> +
> +		cpu at 0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <0>;
> +		};
> +		cpu at 1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <1>;
> +		};
> +	};
> +
> +	soc {
> +		compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus",
> +			     "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		controller = <&mbusc>;
> +		interrupt-parent = <&gic>;
> +		pcie-mem-aperture = <0xe0000000 0x8000000>;
> +		pcie-io-aperture  = <0xe8000000 0x100000>;
> +
> +		bootrom {
> +			compatible = "marvell,bootrom";
> +			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
> +		};
> +
> +		internal-regs {
> +			compatible = "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
> +
> +			scu at c000 {
> +				compatible = "arm,cortex-a9-scu";
> +				reg = <0xc000 0x100>;
> +			};
> +
> +			timer at c600 {
> +				compatible = "arm,cortex-a9-twd-timer";
> +				reg = <0xc600 0x20>;
> +				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
> +				clocks = <&coreclk 2>;
> +			};
> +
> +			gic: interrupt-controller at d000 {
> +				compatible = "arm,cortex-a9-gic";
> +				#interrupt-cells = <3>;
> +				#size-cells = <0>;
> +				interrupt-controller;
> +				reg = <0xd000 0x1000>,
> +				      <0xc100 0x100>;
> +			};
> +
> +			i2c0: i2c at 11000 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11000 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c at 11100 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11100 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c2: i2c at 11200 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11200 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			i2c3: i2c at 11300 {
> +				compatible = "marvell,mv64xxx-i2c";
> +				reg = <0x11300 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +				timeout-ms = <1000>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12000 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12000 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12100 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12100 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12200 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12200 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			serial at 12300 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12300 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clocks = <&coreclk 0>;
> +				status = "disabled";
> +			};
> +
> +			pinctrl at 18000 {
> +				i2c0_pins: i2c0-pins {
> +					marvell,pins = "mpp2", "mpp3";
> +					marvell,function = "i2c0";
> +				};
> +			};
> +
> +			system-controller at 18200 {
> +				compatible = "marvell,armada-390-system-controller",
> +					     "marvell,armada-370-xp-system-controller";
> +				reg = <0x18200 0x100>;
> +			};
> +
> +			gateclk: clock-gating-control at 18220 {
> +				compatible = "marvell,armada-390-gating-clock";
> +				reg = <0x18220 0x4>;
> +				clocks = <&coreclk 0>;
> +				#clock-cells = <1>;
> +			};
> +
> +			coreclk: mvebu-sar at 18600 {
> +				compatible = "marvell,armada-390-core-clock";
> +				reg = <0x18600 0x04>;
> +				#clock-cells = <1>;
> +			};
> +
> +			mbusc: mbus-controller at 20000 {
> +				compatible = "marvell,mbus-controller";
> +				reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>;
> +			};
> +
> +			mpic: interrupt-controller at 20000 {

The unit-address doesn't match the reg address.

> +				compatible = "marvell,mpic";
> +				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
> +				#interrupt-cells = <1>;
> +				#size-cells = <1>;
> +				interrupt-controller;
> +				msi-controller;
> +				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			timer at 20300 {
> +				compatible = "marvell,armada-380-timer",
> +					     "marvell,armada-xp-timer";
> +				reg = <0x20300 0x30>, <0x21040 0x30>;
> +				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +						      <&mpic 5>,
> +						      <&mpic 6>;
> +				clocks = <&coreclk 2>, <&coreclk 5>;
> +				clock-names = "nbclk", "fixed";
> +			};
> +
> +			cpurst at 20800 {
> +				compatible = "marvell,armada-370-cpu-reset";
> +				reg = <0x20800 0x10>;
> +			};
> +
> +			pmsu at 22000 {
> +				compatible = "marvell,armada-390-pmsu",
> +					     "marvell,armada-380-pmsu";
> +				reg = <0x22000 0x1000>;
> +			};
> +		};
> +
> +		pcie-controller {
> +			compatible = "marvell,armada-370-pcie";
> +			status = "disabled";
> +			device_type = "pci";
> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			msi-parent = <&mpic>;
> +			bus-range = <0x00 0xff>;
> +
> +			ranges =
> +			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
> +				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
> +				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
> +				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
> +				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
> +				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
> +				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
> +				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
> +				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
> +				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
> +				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
> +				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
> +
> +			/*
> +			 * This port can be either x4 or x1. When
> +			 * configured in x4 by the bootloader, then
> +			 * pcie at 4,0 is not available.
> +			 */
> +			pcie at 1,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
> +				reg = <0x0800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
> +					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <0>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 8>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie at 2,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
> +				reg = <0x1000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
> +					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <1>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 5>;
> +				status = "disabled";
> +			};
> +
> +			/* x1 port */
> +			pcie at 3,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
> +				reg = <0x1800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
> +					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <2>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 6>;
> +				status = "disabled";
> +			};
> +
> +			/*
> +			 * x1 port only available when pcie at 1,0 is
> +			 * configured as a x1 port
> +			 */
> +			pcie at 4,0 {
> +				device_type = "pci";
> +				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
> +				reg = <0x2000 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
> +					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
> +				interrupt-map-mask = <0 0 0 0>;
> +				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> +				marvell,pcie-port = <3>;
> +				marvell,pcie-lane = <0>;
> +				clocks = <&gateclk 7>;
> +				status = "disabled";
> +			};
> +		};
> +	};
> +};
> -- 
> 2.1.0
> 

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150206/63783d8a/attachment-0001.sig>

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
  2015-02-06 17:05     ` Andrew Lunn
@ 2015-02-20 11:11       ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 11:11 UTC (permalink / raw)
  To: Andrew Lunn
  Cc: Mark Rutland, devicetree, Mike Turquette, Jason Cooper,
	Pawel Moll, Ian Campbell, Linus Walleij, Stephen Boyd,
	Nadav Haklai, linux-gpio, Lior Amsalem, Rob Herring,
	Ezequiel Garcia, Kumar Gala, Gregory Clement, Maxime Ripard,
	Tawfik Bayouk, linux-arm-kernel, Sebastian Hesselbarth

Dear Andrew Lunn,

On Fri, 6 Feb 2015 18:05:21 +0100, Andrew Lunn wrote:

> I wondering if there should be an explanation for the less common
> names here. I'm guessing dev is a device bus of some sort? What is
> xsmi? Some sort of extended System Management Interface? And m?

"dev" is the Device Bus indeed, used for example for NOR or NAND.

"m" stands for memory. The m(decc) signal is asserted when a memory ECC
error occurred, while the m(vtt) signal is the DRAM VTT Power Control
signal. No idea what this is.

"xsmi" is indeed some other SMI bus, not clear yet how it compares to
the regular SMI bus.

Both "dev" and "m" are already used by many of the existing pinctrl DT
bindings for Marvell platforms, so I'm not sure documenting them
specifically in the Armada 39x pinctrl DT binding document makes a lot
of sense. Where should we document them, then? In the generic
'marvell,mvebu-pinctrl.txt' DT binding file ?

Best regards,

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
@ 2015-02-20 11:11       ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 11:11 UTC (permalink / raw)
  To: linux-arm-kernel

Dear Andrew Lunn,

On Fri, 6 Feb 2015 18:05:21 +0100, Andrew Lunn wrote:

> I wondering if there should be an explanation for the less common
> names here. I'm guessing dev is a device bus of some sort? What is
> xsmi? Some sort of extended System Management Interface? And m?

"dev" is the Device Bus indeed, used for example for NOR or NAND.

"m" stands for memory. The m(decc) signal is asserted when a memory ECC
error occurred, while the m(vtt) signal is the DRAM VTT Power Control
signal. No idea what this is.

"xsmi" is indeed some other SMI bus, not clear yet how it compares to
the regular SMI bus.

Both "dev" and "m" are already used by many of the existing pinctrl DT
bindings for Marvell platforms, so I'm not sure documenting them
specifically in the Armada 39x pinctrl DT binding document makes a lot
of sense. Where should we document them, then? In the generic
'marvell,mvebu-pinctrl.txt' DT binding file ?

Best regards,

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
  2015-02-06 19:57     ` Stephen Boyd
@ 2015-02-20 13:05       ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 13:05 UTC (permalink / raw)
  To: Stephen Boyd
  Cc: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Linus Walleij, Lior Amsalem, Tawfik Bayouk, Nadav Haklai,
	linux-gpio, Ezequiel Garcia, Maxime Ripard, linux-arm-kernel

Dear Stephen Boyd,

On Fri, 06 Feb 2015 11:57:58 -0800, Stephen Boyd wrote:

> > +static const char * const armada_39x_dt_compat[] = {
> 
>  __initconst?

Good idea. This wasn't done for the other mach-mvebu dt_compat tables,
so I've added a patch to do this as well for the other mach-mvebu
dt_compat tables.

Will be in v2.

Thanks!

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 08/10] ARM: mvebu: add core support for Armada 39x
@ 2015-02-20 13:05       ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 13:05 UTC (permalink / raw)
  To: linux-arm-kernel

Dear Stephen Boyd,

On Fri, 06 Feb 2015 11:57:58 -0800, Stephen Boyd wrote:

> > +static const char * const armada_39x_dt_compat[] = {
> 
>  __initconst?

Good idea. This wasn't done for the other mach-mvebu dt_compat tables,
so I've added a patch to do this as well for the other mach-mvebu
dt_compat tables.

Will be in v2.

Thanks!

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  2015-02-06 17:21       ` Andrew Lunn
@ 2015-02-20 14:14         ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 14:14 UTC (permalink / raw)
  To: Andrew Lunn
  Cc: Mark Rutland, devicetree, Mike Turquette, Jason Cooper,
	Pawel Moll, Ian Campbell, Linus Walleij, Stephen Boyd,
	Nadav Haklai, linux-gpio, Lior Amsalem, Rob Herring,
	Ezequiel Garcia, Kumar Gala, Gregory Clement, Maxime Ripard,
	Tawfik Bayouk, linux-arm-kernel, Sebastian Hesselbarth

Dear Andrew Lunn,

On Fri, 6 Feb 2015 18:21:53 +0100, Andrew Lunn wrote:

> > +	chosen {
> > +		bootargs = "console=ttyS0,115200 earlyprintk";
> > +	};
> > +
> 
> Arnd has been encouraging people not use earlyprintk here.  Also a
> stdout-path would be nice. We also seem to be missing aliases for the
> serial ports.

Right.


> > +		internal-regs {
> > +                        i2c@11000 {
> > +				pinctrl-0 = <&i2c0_pins>;
> > +				pinctrl-names = "default";
> > +                                status = "okay";
> > +                                clock-frequency = <100000>;
> > +                        };
> > +
> > +			serial@12000 {
> > +				pinctrl-0 = <&uart0_pins>;
> > +				pinctrl-names = "default";
> > +				status = "okay";
> > +			};
> > +
> 
> Tab vs space issue here somewhere? Probably the i2c node.

Yes, fixed.

> > +			pinctrl@18000 {
> > +				uart0_pins: uart0-pins {
> > +					marvell,pins = "mpp0", "mpp1";
> > +					marvell,function = "ua0";
> > +				};
> > +
> > +				uart1_pins: uart1-pins {
> > +					marvell,pins = "mpp19", "mpp20";
> > +					marvell,function = "ua1";
> > +				};
> 
> Does it make sense to put there in the .dtsi file? I know there are
> other choices, but generally board manufacturers tend to follow the
> reference design.

I am not really convinced here: there are really many possible pin
muxing possibilities. Various pins for UART0 and UART1, whether you use
CTS/RTS or not, etc. I believe this is really the sort of pin mux
configuration that is best left at the board level.

Best regards,

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
@ 2015-02-20 14:14         ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 14:14 UTC (permalink / raw)
  To: linux-arm-kernel

Dear Andrew Lunn,

On Fri, 6 Feb 2015 18:21:53 +0100, Andrew Lunn wrote:

> > +	chosen {
> > +		bootargs = "console=ttyS0,115200 earlyprintk";
> > +	};
> > +
> 
> Arnd has been encouraging people not use earlyprintk here.  Also a
> stdout-path would be nice. We also seem to be missing aliases for the
> serial ports.

Right.


> > +		internal-regs {
> > +                        i2c at 11000 {
> > +				pinctrl-0 = <&i2c0_pins>;
> > +				pinctrl-names = "default";
> > +                                status = "okay";
> > +                                clock-frequency = <100000>;
> > +                        };
> > +
> > +			serial at 12000 {
> > +				pinctrl-0 = <&uart0_pins>;
> > +				pinctrl-names = "default";
> > +				status = "okay";
> > +			};
> > +
> 
> Tab vs space issue here somewhere? Probably the i2c node.

Yes, fixed.

> > +			pinctrl at 18000 {
> > +				uart0_pins: uart0-pins {
> > +					marvell,pins = "mpp0", "mpp1";
> > +					marvell,function = "ua0";
> > +				};
> > +
> > +				uart1_pins: uart1-pins {
> > +					marvell,pins = "mpp19", "mpp20";
> > +					marvell,function = "ua1";
> > +				};
> 
> Does it make sense to put there in the .dtsi file? I know there are
> other choices, but generally board manufacturers tend to follow the
> reference design.

I am not really convinced here: there are really many possible pin
muxing possibilities. Various pins for UART0 and UART1, whether you use
CTS/RTS or not, etc. I believe this is really the sort of pin mux
configuration that is best left at the board level.

Best regards,

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
  2015-02-20 11:11       ` Thomas Petazzoni
@ 2015-02-20 14:18           ` Andrew Lunn
  -1 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-20 14:18 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Mark Rutland, devicetree-u79uwXL29TY76Z2rM5mHXA, Mike Turquette,
	Jason Cooper, Pawel Moll, Ian Campbell, Linus Walleij,
	Stephen Boyd, Nadav Haklai, linux-gpio-u79uwXL29TY76Z2rM5mHXA,
	Lior Amsalem, Rob Herring, Ezequiel Garcia, Kumar Gala,
	Gregory Clement, Maxime Ripard, Tawfik Bayouk,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Sebastian Hesselbarth

> Both "dev" and "m" are already used by many of the existing pinctrl DT
> bindings for Marvell platforms, so I'm not sure documenting them
> specifically in the Armada 39x pinctrl DT binding document makes a lot
> of sense. Where should we document them, then? In the generic
> 'marvell,mvebu-pinctrl.txt' DT binding file ?

Hi Thomas

Yes, that would be a good place to list them.

Thanks
	Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller
@ 2015-02-20 14:18           ` Andrew Lunn
  0 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-20 14:18 UTC (permalink / raw)
  To: linux-arm-kernel

> Both "dev" and "m" are already used by many of the existing pinctrl DT
> bindings for Marvell platforms, so I'm not sure documenting them
> specifically in the Armada 39x pinctrl DT binding document makes a lot
> of sense. Where should we document them, then? In the generic
> 'marvell,mvebu-pinctrl.txt' DT binding file ?

Hi Thomas

Yes, that would be a good place to list them.

Thanks
	Andrew

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  2015-02-20 14:14         ` Thomas Petazzoni
@ 2015-02-20 14:45           ` Andrew Lunn
  -1 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-20 14:45 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Mark Rutland, devicetree, Mike Turquette, Jason Cooper,
	Pawel Moll, Ian Campbell, Linus Walleij, Stephen Boyd,
	Nadav Haklai, linux-gpio, Lior Amsalem, Rob Herring,
	Ezequiel Garcia, Kumar Gala, Gregory Clement, Maxime Ripard,
	Tawfik Bayouk, linux-arm-kernel, Sebastian Hesselbarth

> > > +			pinctrl@18000 {
> > > +				uart0_pins: uart0-pins {
> > > +					marvell,pins = "mpp0", "mpp1";
> > > +					marvell,function = "ua0";
> > > +				};
> > > +
> > > +				uart1_pins: uart1-pins {
> > > +					marvell,pins = "mpp19", "mpp20";
> > > +					marvell,function = "ua1";
> > > +				};
> > 
> > Does it make sense to put there in the .dtsi file? I know there are
> > other choices, but generally board manufacturers tend to follow the
> > reference design.
> 
> I am not really convinced here: there are really many possible pin
> muxing possibilities. Various pins for UART0 and UART1, whether you use
> CTS/RTS or not, etc. I believe this is really the sort of pin mux
> configuration that is best left at the board level.

Hi Thomas

Lets look at this from the perspective of lies, damn lies, and
statistics:

Kirkwood has a default pinmux configuration in kirkwood.dtsi. Two of
the sixty six .dts files overwrite the defaults.

Dove has a default pinmux of uart1, but none for uart0.  None of the
.dts files define a pinmux for uart0 and none overwrite the defaults
for uart1.

Armanda XP has a default pinmux for uart2 and uart2 in armada-xp.dtsi,
but none for uart0 or uart1. None of the .dts files define a pinmux
for uart0 or uart1, and none overwrite the defaults for uart2 or
uart3.

Armada 370 has default pinmux for uart0 and uart1. None of the .dts
files overwrite the defaults.

I'm too lazy to look at 375, 380, and 385.

We have over 80 dts files here with defaults from a .dtsi file, and
only two need anything other than defaults.

	 Andrew

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
@ 2015-02-20 14:45           ` Andrew Lunn
  0 siblings, 0 replies; 48+ messages in thread
From: Andrew Lunn @ 2015-02-20 14:45 UTC (permalink / raw)
  To: linux-arm-kernel

> > > +			pinctrl at 18000 {
> > > +				uart0_pins: uart0-pins {
> > > +					marvell,pins = "mpp0", "mpp1";
> > > +					marvell,function = "ua0";
> > > +				};
> > > +
> > > +				uart1_pins: uart1-pins {
> > > +					marvell,pins = "mpp19", "mpp20";
> > > +					marvell,function = "ua1";
> > > +				};
> > 
> > Does it make sense to put there in the .dtsi file? I know there are
> > other choices, but generally board manufacturers tend to follow the
> > reference design.
> 
> I am not really convinced here: there are really many possible pin
> muxing possibilities. Various pins for UART0 and UART1, whether you use
> CTS/RTS or not, etc. I believe this is really the sort of pin mux
> configuration that is best left at the board level.

Hi Thomas

Lets look at this from the perspective of lies, damn lies, and
statistics:

Kirkwood has a default pinmux configuration in kirkwood.dtsi. Two of
the sixty six .dts files overwrite the defaults.

Dove has a default pinmux of uart1, but none for uart0.  None of the
.dts files define a pinmux for uart0 and none overwrite the defaults
for uart1.

Armanda XP has a default pinmux for uart2 and uart2 in armada-xp.dtsi,
but none for uart0 or uart1. None of the .dts files define a pinmux
for uart0 or uart1, and none overwrite the defaults for uart2 or
uart3.

Armada 370 has default pinmux for uart0 and uart1. None of the .dts
files overwrite the defaults.

I'm too lazy to look at 375, 380, and 385.

We have over 80 dts files here with defaults from a .dtsi file, and
only two need anything other than defaults.

	 Andrew

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  2015-02-20 14:45           ` Andrew Lunn
@ 2015-02-20 15:46             ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 15:46 UTC (permalink / raw)
  To: Andrew Lunn
  Cc: Mark Rutland, devicetree, Mike Turquette, Jason Cooper,
	Pawel Moll, Ian Campbell, Linus Walleij, Stephen Boyd,
	Nadav Haklai, linux-gpio, Lior Amsalem, Rob Herring,
	Ezequiel Garcia, Kumar Gala, Gregory Clement, Maxime Ripard,
	Tawfik Bayouk, linux-arm-kernel, Sebastian Hesselbarth

Dear Andrew Lunn,

On Fri, 20 Feb 2015 15:45:47 +0100, Andrew Lunn wrote:

> Lets look at this from the perspective of lies, damn lies, and
> statistics:
> 
> Kirkwood has a default pinmux configuration in kirkwood.dtsi. Two of
> the sixty six .dts files overwrite the defaults.
> 
> Dove has a default pinmux of uart1, but none for uart0.  None of the
> .dts files define a pinmux for uart0 and none overwrite the defaults
> for uart1.
> 
> Armanda XP has a default pinmux for uart2 and uart2 in armada-xp.dtsi,
> but none for uart0 or uart1. None of the .dts files define a pinmux
> for uart0 or uart1, and none overwrite the defaults for uart2 or
> uart3.
> 
> Armada 370 has default pinmux for uart0 and uart1. None of the .dts
> files overwrite the defaults.
> 
> I'm too lazy to look at 375, 380, and 385.
> 
> We have over 80 dts files here with defaults from a .dtsi file, and
> only two need anything other than defaults.

Fair enough :)

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board
@ 2015-02-20 15:46             ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-02-20 15:46 UTC (permalink / raw)
  To: linux-arm-kernel

Dear Andrew Lunn,

On Fri, 20 Feb 2015 15:45:47 +0100, Andrew Lunn wrote:

> Lets look at this from the perspective of lies, damn lies, and
> statistics:
> 
> Kirkwood has a default pinmux configuration in kirkwood.dtsi. Two of
> the sixty six .dts files overwrite the defaults.
> 
> Dove has a default pinmux of uart1, but none for uart0.  None of the
> .dts files define a pinmux for uart0 and none overwrite the defaults
> for uart1.
> 
> Armanda XP has a default pinmux for uart2 and uart2 in armada-xp.dtsi,
> but none for uart0 or uart1. None of the .dts files define a pinmux
> for uart0 or uart1, and none overwrite the defaults for uart2 or
> uart3.
> 
> Armada 370 has default pinmux for uart0 and uart1. None of the .dts
> files overwrite the defaults.
> 
> I'm too lazy to look at 375, 380, and 385.
> 
> We have over 80 dts files here with defaults from a .dtsi file, and
> only two need anything other than defaults.

Fair enough :)

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
  2015-02-06 15:57   ` Thomas Petazzoni
@ 2015-03-04 12:54     ` Linus Walleij
  -1 siblings, 0 replies; 48+ messages in thread
From: Linus Walleij @ 2015-03-04 12:54 UTC (permalink / raw)
  To: Thomas Petazzoni
  Cc: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, linux-arm-kernel, linux-gpio, Tawfik Bayouk,
	Nadav Haklai, Lior Amsalem, Ezequiel Garcia, Maxime Ripard

On Fri, Feb 6, 2015 at 4:57 PM, Thomas Petazzoni
<thomas.petazzoni@free-electrons.com> wrote:

> This commit adds a new pinctrl driver for the Marvell Armada 39x
> family of processors, which hooks into the existing infrastructure to
> support pin-muxing on Marvell EBU processors. Two variants of the
> Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
> 398), which have a few differences in the available functions for
> certain pins.
>
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

Patch applied.

Yours,
Linus Walleij

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
@ 2015-03-04 12:54     ` Linus Walleij
  0 siblings, 0 replies; 48+ messages in thread
From: Linus Walleij @ 2015-03-04 12:54 UTC (permalink / raw)
  To: linux-arm-kernel

On Fri, Feb 6, 2015 at 4:57 PM, Thomas Petazzoni
<thomas.petazzoni@free-electrons.com> wrote:

> This commit adds a new pinctrl driver for the Marvell Armada 39x
> family of processors, which hooks into the existing infrastructure to
> support pin-muxing on Marvell EBU processors. Two variants of the
> Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
> 398), which have a few differences in the available functions for
> certain pins.
>
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

Patch applied.

Yours,
Linus Walleij

^ permalink raw reply	[flat|nested] 48+ messages in thread
* Re: [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
  2015-03-04 12:54     ` Linus Walleij
@ 2015-03-04 13:05       ` Thomas Petazzoni
  -1 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-03-04 13:05 UTC (permalink / raw)
  To: Linus Walleij
  Cc: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth,
	Gregory Clement, devicetree, Rob Herring, Pawel Moll,
	Mark Rutland, Ian Campbell, Kumar Gala, Mike Turquette,
	Stephen Boyd, linux-arm-kernel, linux-gpio, Tawfik Bayouk,
	Nadav Haklai, Lior Amsalem, Ezequiel Garcia, Maxime Ripard

Dear Linus Walleij,

On Wed, 4 Mar 2015 13:54:42 +0100, Linus Walleij wrote:
> On Fri, Feb 6, 2015 at 4:57 PM, Thomas Petazzoni
> <thomas.petazzoni@free-electrons.com> wrote:
> 
> > This commit adds a new pinctrl driver for the Marvell Armada 39x
> > family of processors, which hooks into the existing infrastructure to
> > support pin-muxing on Marvell EBU processors. Two variants of the
> > Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
> > 398), which have a few differences in the available functions for
> > certain pins.
> >
> > Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> 
> Patch applied.

I'm surprised you applied the driver of the first iteration of the
patches, and not the v3 I sent just yesterday. Even though if I
remember correctly there were no changes on the pinctrl driver itself.

Also, can you apply:

  devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller

Thanks!

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
* [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x
@ 2015-03-04 13:05       ` Thomas Petazzoni
  0 siblings, 0 replies; 48+ messages in thread
From: Thomas Petazzoni @ 2015-03-04 13:05 UTC (permalink / raw)
  To: linux-arm-kernel

Dear Linus Walleij,

On Wed, 4 Mar 2015 13:54:42 +0100, Linus Walleij wrote:
> On Fri, Feb 6, 2015 at 4:57 PM, Thomas Petazzoni
> <thomas.petazzoni@free-electrons.com> wrote:
> 
> > This commit adds a new pinctrl driver for the Marvell Armada 39x
> > family of processors, which hooks into the existing infrastructure to
> > support pin-muxing on Marvell EBU processors. Two variants of the
> > Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
> > 398), which have a few differences in the available functions for
> > certain pins.
> >
> > Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> 
> Patch applied.

I'm surprised you applied the driver of the first iteration of the
patches, and not the v3 I sent just yesterday. Even though if I
remember correctly there were no changes on the pinctrl driver itself.

Also, can you apply:

  devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller

Thanks!

Thomas
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 48+ messages in thread
end of thread, other threads:[~2015-03-04 13:05 UTC | newest]

Thread overview: 48+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-02-06 15:57 [PATCH 00/10] ARM: mvebu: add basic support for Armada 39x Thomas Petazzoni
2015-02-06 15:57 ` Thomas Petazzoni
2015-02-06 15:57 ` [PATCH 01/10] devicetree: bindings: add DT binding for the Marvell Armada 39x SoC family Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-02-06 15:57 ` [PATCH 02/10] devicetree: bindings: update DT bindings for Marvell EBU clock support Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-02-06 15:57 ` [PATCH 03/10] devicetree: bindings: add Device Tree bindings for Armada 39x pin-muxing controller Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-02-06 17:05   ` Andrew Lunn
2015-02-06 17:05     ` Andrew Lunn
2015-02-20 11:11     ` Thomas Petazzoni
2015-02-20 11:11       ` Thomas Petazzoni
     [not found]       ` <20150220121134.25cb865c-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
2015-02-20 14:18         ` Andrew Lunn
2015-02-20 14:18           ` Andrew Lunn
2015-02-06 15:57 ` [PATCH 05/10] clk: mvebu: extend common code to allow an optional refclk Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-02-06 15:57 ` [PATCH 06/10] clk: mvebu: add Marvell Armada 39x driver Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-02-06 15:57 ` [PATCH 07/10] pinctrl: mvebu: add pinctrl driver for Marvell Armada 39x Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-03-04 12:54   ` Linus Walleij
2015-03-04 12:54     ` Linus Walleij
2015-03-04 13:05     ` Thomas Petazzoni
2015-03-04 13:05       ` Thomas Petazzoni
2015-02-06 15:57 ` [PATCH 08/10] ARM: mvebu: add core support for " Thomas Petazzoni
2015-02-06 15:57   ` Thomas Petazzoni
2015-02-06 19:57   ` Stephen Boyd
2015-02-06 19:57     ` Stephen Boyd
2015-02-20 13:05     ` Thomas Petazzoni
2015-02-20 13:05       ` Thomas Petazzoni
     [not found]   ` <1423238276-9206-9-git-send-email-thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
2015-02-06 20:31     ` Maxime Ripard
2015-02-06 20:31       ` Maxime Ripard
     [not found] ` <1423238276-9206-1-git-send-email-thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
2015-02-06 15:57   ` [PATCH 04/10] devicetree: bindings: add new SMP enable method for Marvell " Thomas Petazzoni
2015-02-06 15:57     ` Thomas Petazzoni
2015-02-06 15:57   ` [PATCH 09/10] ARM: mvebu: add Device Tree files for Armada 39x SoC and board Thomas Petazzoni
2015-02-06 15:57     ` Thomas Petazzoni
2015-02-06 17:21     ` Andrew Lunn
2015-02-06 17:21       ` Andrew Lunn
2015-02-20 14:14       ` Thomas Petazzoni
2015-02-20 14:14         ` Thomas Petazzoni
2015-02-20 14:45         ` Andrew Lunn
2015-02-20 14:45           ` Andrew Lunn
2015-02-20 15:46           ` Thomas Petazzoni
2015-02-20 15:46             ` Thomas Petazzoni
2015-02-06 20:39     ` Maxime Ripard
2015-02-06 20:39       ` Maxime Ripard
2015-02-06 15:57   ` [PATCH 10/10] Documentation: arm: update supported Marvell EBU processors Thomas Petazzoni
2015-02-06 15:57     ` Thomas Petazzoni

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.