[PATCH v2 0/2] add dts for PopMetal board

[PATCH v2 0/2] add dts for PopMetal board

[Andy Yan]

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).

http://wiki.chipspark.com/en/index.php?title=PopMetal

This patch add basic support for it, which can boot the board
into a shell with linux boot logo on hdmi, sdcard and many
sensors enabled. More feather will be enabled later.

Changes in v2:
- change "PopMetal PopMetal-RK3288 board" to "ChipSPARK PopMetal-RK3288 board"
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"

Andy Yan (2):
  dt-bindings: add root compatible property for PopMetal board
  ARM: dts: add rk3288 PopMetal board

 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/rk3288-popmetal.dts              | 447 +++++++++++++++++++++
 2 files changed, 451 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts

-- 
1.9.1

[PATCH v2 0/2] add dts for PopMetal board

[Andy Yan]

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).

http://wiki.chipspark.com/en/index.php?title=PopMetal

This patch add basic support for it, which can boot the board
into a shell with linux boot logo on hdmi, sdcard and many
sensors enabled. More feather will be enabled later.

Changes in v2:
- change "PopMetal PopMetal-RK3288 board" to "ChipSPARK PopMetal-RK3288 board"
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"

Andy Yan (2):
  dt-bindings: add root compatible property for PopMetal board
  ARM: dts: add rk3288 PopMetal board

 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/rk3288-popmetal.dts              | 447 +++++++++++++++++++++
 2 files changed, 451 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts

-- 
1.9.1


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 0/2] add dts for PopMetal board

[Andy Yan]

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).

http://wiki.chipspark.com/en/index.php?title=PopMetal

This patch add basic support for it, which can boot the board
into a shell with linux boot logo on hdmi, sdcard and many
sensors enabled. More feather will be enabled later.

Changes in v2:
- change "PopMetal PopMetal-RK3288 board" to "ChipSPARK PopMetal-RK3288 board"
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"

Andy Yan (2):
  dt-bindings: add root compatible property for PopMetal board
  ARM: dts: add rk3288 PopMetal board

 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/rk3288-popmetal.dts              | 447 +++++++++++++++++++++
 2 files changed, 451 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts

-- 
1.9.1

[PATCH v2 1/2] dt-bindings: add root compatible property for PopMetal board

[Andy Yan]

PopMetal board is a rk3288 based board made by ChipSpark, this
add root compatible property for it

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>

---

Changes in v2:
- change "PopMetal PopMetal-RK3288 board" to "ChipSPARK PopMetal-RK3288 board"

 Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 6809e4e..60d4a1e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -22,3 +22,7 @@ Rockchip platforms device tree bindings
       - compatible = "firefly,firefly-rk3288", "rockchip,rk3288";
     or
       - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
+
+- ChipSPARK PopMetal-RK3288 board:
+    Required root node properties:
+      - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
-- 
1.9.1

[PATCH v2 1/2] dt-bindings: add root compatible property for PopMetal board

[Andy Yan]

PopMetal board is a rk3288 based board made by ChipSpark, this
add root compatible property for it

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>

---

Changes in v2:
- change "PopMetal PopMetal-RK3288 board" to "ChipSPARK PopMetal-RK3288 board"

 Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 6809e4e..60d4a1e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -22,3 +22,7 @@ Rockchip platforms device tree bindings
       - compatible = "firefly,firefly-rk3288", "rockchip,rk3288";
     or
       - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
+
+- ChipSPARK PopMetal-RK3288 board:
+    Required root node properties:
+      - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
-- 
1.9.1

[PATCH v2 2/2] ARM: dts: add rk3288 PopMetal board

[Andy Yan]

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).

This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>

---

Changes in v2:
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"
- add cpu0-supply
- add supply for rk808 regulator

 arch/arm/boot/dts/rk3288-popmetal.dts | 447 ++++++++++++++++++++++++++++++++++
 1 file changed, 447 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts

diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts
new file mode 100644
index 0000000..d081f0e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-popmetal.dts
@@ -0,0 +1,447 @@
+/*
+ * Copyright (c) 2014, 2015 Andy Yan <andy.yan@rock-chips.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+	model = "PopMetal-RK3288";
+	compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+	memory{
+		reg = <0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button@0 {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <116>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	ir: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;                     /* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&gmac {
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_lan: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_sd: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			ldo5: LDO_REG5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "ldo5";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca_codec: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_codec";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ak8963: ak8963@0d {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&comp_int>;
+	};
+
+	l3g4200d: l3g4200d@68 {
+		compatible = "st,l3g4200d-gyro";
+		st,drdy-int-pin = <2>;
+		reg = <0x6b>;
+	};
+
+	mma8452: mma8452@1d {
+		compatible = "fsl,mma8452";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsensor_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	ak8963 {
+		comp_int: comp-int {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	mma8452 {
+		gsensor_int: gsensor-int {
+			rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
1.9.1

[PATCH v2 2/2] ARM: dts: add rk3288 PopMetal board

[Andy Yan]

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).

This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled

Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

---

Changes in v2:
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"
- add cpu0-supply
- add supply for rk808 regulator

 arch/arm/boot/dts/rk3288-popmetal.dts | 447 ++++++++++++++++++++++++++++++++++
 1 file changed, 447 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts

diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts
new file mode 100644
index 0000000..d081f0e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-popmetal.dts
@@ -0,0 +1,447 @@
+/*
+ * Copyright (c) 2014, 2015 Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+	model = "PopMetal-RK3288";
+	compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+	memory{
+		reg = <0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button@0 {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <116>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	ir: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;                     /* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&gmac {
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_lan: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_sd: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			ldo5: LDO_REG5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "ldo5";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca_codec: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_codec";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ak8963: ak8963@0d {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&comp_int>;
+	};
+
+	l3g4200d: l3g4200d@68 {
+		compatible = "st,l3g4200d-gyro";
+		st,drdy-int-pin = <2>;
+		reg = <0x6b>;
+	};
+
+	mma8452: mma8452@1d {
+		compatible = "fsl,mma8452";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsensor_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	ak8963 {
+		comp_int: comp-int {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	mma8452 {
+		gsensor_int: gsensor-int {
+			rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
1.9.1


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 2/2] ARM: dts: add rk3288 PopMetal board

[Andy Yan]

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).

This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>

---

Changes in v2:
- use GPL + X11 dual license, adviced by Heiko
- indent pwrbtn
- move node "ak8963" before "buttons"
- add cpu0-supply
- add supply for rk808 regulator

 arch/arm/boot/dts/rk3288-popmetal.dts | 447 ++++++++++++++++++++++++++++++++++
 1 file changed, 447 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-popmetal.dts

diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts
new file mode 100644
index 0000000..d081f0e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-popmetal.dts
@@ -0,0 +1,447 @@
+/*
+ * Copyright (c) 2014, 2015 Andy Yan <andy.yan@rock-chips.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+	model = "PopMetal-RK3288";
+	compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+	memory{
+		reg = <0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button at 0 {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <116>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	ir: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;                     /* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&gmac {
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic at 1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_lan: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_sd: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			ldo5: LDO_REG5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "ldo5";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca_codec: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_codec";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ak8963: ak8963 at 0d {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&comp_int>;
+	};
+
+	l3g4200d: l3g4200d at 68 {
+		compatible = "st,l3g4200d-gyro";
+		st,drdy-int-pin = <2>;
+		reg = <0x6b>;
+	};
+
+	mma8452: mma8452 at 1d {
+		compatible = "fsl,mma8452";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsensor_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	ak8963 {
+		comp_int: comp-int {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	mma8452 {
+		gsensor_int: gsensor-int {
+			rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
1.9.1

Re: [PATCH v2 0/2] add dts for PopMetal board

[Heiko Stuebner]

Hi Andy,

Am Sonntag, 1. März 2015, 17:25:14 schrieb Andy Yan:
> PopMetal is a rockchip rk3288 based board made by ChipSpark,
> which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
> sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).
> 
> http://wiki.chipspark.com/en/index.php?title=PopMetal
> 
> This patch add basic support for it, which can boot the board
> into a shell with linux boot logo on hdmi, sdcard and many
> sensors enabled. More feather will be enabled later.

I've added both patches to my dts branch


Heiko

[PATCH v2 0/2] add dts for PopMetal board

[Heiko Stuebner]

Hi Andy,

Am Sonntag, 1. M?rz 2015, 17:25:14 schrieb Andy Yan:
> PopMetal is a rockchip rk3288 based board made by ChipSpark,
> which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
> sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).
> 
> http://wiki.chipspark.com/en/index.php?title=PopMetal
> 
> This patch add basic support for it, which can boot the board
> into a shell with linux boot logo on hdmi, sdcard and many
> sensors enabled. More feather will be enabled later.

I've added both patches to my dts branch


Heiko

Re: [PATCH v2 0/2] add dts for PopMetal board

[Andy Yan]

Hi Heiko:
  Thanks very much.
On 2015年03月05日 03:57, Heiko Stuebner wrote:
> Hi Andy,
>
> Am Sonntag, 1. März 2015, 17:25:14 schrieb Andy Yan:
>> PopMetal is a rockchip rk3288 based board made by ChipSpark,
>> which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
>> sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).
>>
>> http://wiki.chipspark.com/en/index.php?title=PopMetal
>>
>> This patch add basic support for it, which can boot the board
>> into a shell with linux boot logo on hdmi, sdcard and many
>> sensors enabled. More feather will be enabled later.
> I've added both patches to my dts branch
>
>
> Heiko
>
>
>

[PATCH v2 0/2] add dts for PopMetal board

[Andy Yan]

Hi Heiko:
  Thanks very much.
On 2015?03?05? 03:57, Heiko Stuebner wrote:
> Hi Andy,
>
> Am Sonntag, 1. M?rz 2015, 17:25:14 schrieb Andy Yan:
>> PopMetal is a rockchip rk3288 based board made by ChipSpark,
>> which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
>> sensors such as gyroscope(L3G4200D),accelerometer(mma8452),compass(AK8963C).
>>
>> http://wiki.chipspark.com/en/index.php?title=PopMetal
>>
>> This patch add basic support for it, which can boot the board
>> into a shell with linux boot logo on hdmi, sdcard and many
>> sensors enabled. More feather will be enabled later.
> I've added both patches to my dts branch
>
>
> Heiko
>
>
>