* [PATCH 0/3] Remove few inactive omap3 legacy board-*.c files
@ 2015-03-17 0:25 ` Tony Lindgren
0 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-omap; +Cc: linux-arm-kernel
Hi all,
I'm hoping to get the status of the remaining omap3 legacy board-*.c
files into a known state.
And I figured the best way to do that is by removing few of them that
I think are all inactive. If you are using these, please yell now!
The reason for trying to remove them now is that I don't want any
suprises with missing .dts files later on when we remove the
remaining omap3 legacy booting support.
For now, we can just simply revert these patches as needed until we
have the related .dts files done. After we've dropped the remaining
omap3 legacy booting support in a few merge cycles, reverting will
be much harder.
Regards,
Tony
Tony Lindgren (3):
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
arch/arm/mach-omap2/Kconfig | 18 -
arch/arm/mach-omap2/Makefile | 4 -
arch/arm/mach-omap2/board-devkit8000.c | 654 -----------------------------
arch/arm/mach-omap2/board-omap3stalker.c | 433 -------------------
arch/arm/mach-omap2/board-omap3touchbook.c | 395 -----------------
5 files changed, 1504 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-devkit8000.c
delete mode 100644 arch/arm/mach-omap2/board-omap3stalker.c
delete mode 100644 arch/arm/mach-omap2/board-omap3touchbook.c
--
2.1.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/3] Remove few inactive omap3 legacy board-*.c files
@ 2015-03-17 0:25 ` Tony Lindgren
0 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-arm-kernel
Hi all,
I'm hoping to get the status of the remaining omap3 legacy board-*.c
files into a known state.
And I figured the best way to do that is by removing few of them that
I think are all inactive. If you are using these, please yell now!
The reason for trying to remove them now is that I don't want any
suprises with missing .dts files later on when we remove the
remaining omap3 legacy booting support.
For now, we can just simply revert these patches as needed until we
have the related .dts files done. After we've dropped the remaining
omap3 legacy booting support in a few merge cycles, reverting will
be much harder.
Regards,
Tony
Tony Lindgren (3):
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
arch/arm/mach-omap2/Kconfig | 18 -
arch/arm/mach-omap2/Makefile | 4 -
arch/arm/mach-omap2/board-devkit8000.c | 654 -----------------------------
arch/arm/mach-omap2/board-omap3stalker.c | 433 -------------------
arch/arm/mach-omap2/board-omap3touchbook.c | 395 -----------------
5 files changed, 1504 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-devkit8000.c
delete mode 100644 arch/arm/mach-omap2/board-omap3stalker.c
delete mode 100644 arch/arm/mach-omap2/board-omap3touchbook.c
--
2.1.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
2015-03-17 0:25 ` Tony Lindgren
@ 2015-03-17 0:25 ` Tony Lindgren
-1 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-omap; +Cc: Jason Lam, linux-arm-kernel
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Also looks like this board is no longer listed on ema-tech.com
product page at:
http://ema-tech.com/en/categories.html
Cc: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 2 -
arch/arm/mach-omap2/board-omap3stalker.c | 433 -------------------------------
3 files changed, 441 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-omap3stalker.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 2b8e477..88e3eaf 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -260,12 +260,6 @@ config MACH_CM_T35
config MACH_CM_T3730
bool
-config MACH_SBC3530
- bool "OMAP3 SBC STALKER board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CUS
-
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b83f18f..10b9563 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -256,8 +256,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
-obj-$(CONFIG_MACH_SBC3530) += board-omap3stalker.o
-
# Platform specific device init code
omap-flash-$(CONFIG_MTD_NAND_OMAP2) := board-flash.o
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
deleted file mode 100644
index 6311f4b..0000000
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Guangzhou EMA-Tech
- *
- * Modified from mach-omap2/board-omap3evm.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/platform_data/at24.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include "gpmc-smsc911x.h"
-
-#define OMAP3STALKER_ETHR_START 0x2c000000
-#define OMAP3STALKER_ETHR_SIZE 1024
-#define OMAP3STALKER_ETHR_GPIO_IRQ 19
-#define OMAP3STALKER_SMC911X_CS 5
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = OMAP3STALKER_SMC911X_CS,
- .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
- .gpio_reset = -EINVAL,
- .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static inline void __init omap3stalker_init_eth(void)
-{
- omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3stalker_init_eth(void)
-{
- return;
-}
-#endif
-
-/*
- * OMAP3 DSS control signals
- */
-
-#define DSS_ENABLE_GPIO 199
-#define LCD_PANEL_BKLIGHT_GPIO 210
-#define ENABLE_VPLL2_DEV_GRP 0xE0
-
-static void __init omap3_stalker_display_init(void)
-{
- return;
-}
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = -1,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = DSS_ENABLE_GPIO,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3stalker_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3stalker_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
- .invert_polarity = false,
-};
-
-static struct platform_device omap3stalker_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &omap3stalker_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_stalker_dss_data = {
- .default_display_name = "dvi",
-};
-
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3stalker_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vmmc1_supply),
- .consumer_supplies = omap3stalker_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data omap3stalker_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vsim_supply),
- .consumer_supplies = omap3stalker_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = 23,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 18,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "stalker:D8:usr0",
- .default_trigger = "default-on",
- .gpio = 126,
- },
- {
- .name = "stalker:D9:usr1",
- .default_trigger = "default-on",
- .gpio = 127,
- },
- {
- .name = "stalker:D3:mmc0",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "mmc0",
- },
- {
- .name = "stalker:D4:heartbeat",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "heartbeat",
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static int
-omap3stalker_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /*
- * Most GPIOs are for USB OTG. Some are mostly sent to
- * the P2 connector; notably LEDA for the LCD backlight.
- */
-
- /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
- "EN_LCD_BKL");
-
- /* gpio + 7 == DVI Enable */
- gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
- /* GPIO + 13 == ledsync (out, heartbeat) */
- gpio_leds[3].gpio = gpio + 13;
-
- platform_device_register(&leds_gpio);
- return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
- .use_leds = true,
- .setup = omap3stalker_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_DOWN),
- KEY(0, 2, KEY_ENTER),
- KEY(0, 3, KEY_M),
-
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_I),
- KEY(1, 3, KEY_N),
-
- KEY(2, 0, KEY_A),
- KEY(2, 1, KEY_E),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_O),
-
- KEY(3, 0, KEY_B),
- KEY(3, 1, KEY_F),
- KEY(3, 2, KEY_K),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3stalker_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-static struct twl4030_platform_data omap3stalker_twldata = {
- /* platform_data for children goes here */
- .keypad = &omap3stalker_kp_data,
- .gpio = &omap3stalker_gpio_data,
- .vmmc1 = &omap3stalker_vmmc1,
- .vsim = &omap3stalker_vsim,
-};
-
-static struct at24_platform_data fram_info = {
- .byte_len = (64 * 1024) / 8,
- .page_size = 8192,
- .flags = AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
- {
- I2C_BOARD_INFO("24c64", 0x50),
- .flags = I2C_CLIENT_WAKE,
- .platform_data = &fram_info,
- },
-};
-
-static int __init omap3_stalker_i2c_init(void)
-{
- omap3_pmic_get_config(&omap3stalker_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
- TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- omap3stalker_twldata.vdac->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.name = "VDVI";
-
- omap3_pmic_init("twl4030", &omap3stalker_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
- ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
- return 0;
-}
-
-#define OMAP3_STALKER_TS_GPIO 175
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = 21,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct platform_device *omap3_stalker_devices[] __initdata = {
- &keys_gpio,
- &omap3stalker_tfp410_device,
- &omap3stalker_dvi_connector_device,
- &omap3stalker_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- {.reg_offset = OMAP_MUX_TERMINATOR},
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3_stalker_init(void)
-{
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- omap_hsmmc_init(mmc);
-
- omap3_stalker_i2c_init();
-
- platform_add_devices(omap3_stalker_devices,
- ARRAY_SIZE(omap3_stalker_devices));
-
- omap_display_init(&omap3_stalker_dss_data);
-
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
-
- omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
-
- omap3stalker_init_eth();
- omap3_stalker_display_init();
-/* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(SBC3530, "OMAP3 STALKER")
- /* Maintainer: Jason Lam -lzg@ema-tech.com */
- .atag_offset = 0x100,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_stalker_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
@ 2015-03-17 0:25 ` Tony Lindgren
0 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-arm-kernel
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Also looks like this board is no longer listed on ema-tech.com
product page at:
http://ema-tech.com/en/categories.html
Cc: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 2 -
arch/arm/mach-omap2/board-omap3stalker.c | 433 -------------------------------
3 files changed, 441 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-omap3stalker.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 2b8e477..88e3eaf 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -260,12 +260,6 @@ config MACH_CM_T35
config MACH_CM_T3730
bool
-config MACH_SBC3530
- bool "OMAP3 SBC STALKER board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CUS
-
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b83f18f..10b9563 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -256,8 +256,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
-obj-$(CONFIG_MACH_SBC3530) += board-omap3stalker.o
-
# Platform specific device init code
omap-flash-$(CONFIG_MTD_NAND_OMAP2) := board-flash.o
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
deleted file mode 100644
index 6311f4b..0000000
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Guangzhou EMA-Tech
- *
- * Modified from mach-omap2/board-omap3evm.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/platform_data/at24.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include "gpmc-smsc911x.h"
-
-#define OMAP3STALKER_ETHR_START 0x2c000000
-#define OMAP3STALKER_ETHR_SIZE 1024
-#define OMAP3STALKER_ETHR_GPIO_IRQ 19
-#define OMAP3STALKER_SMC911X_CS 5
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = OMAP3STALKER_SMC911X_CS,
- .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
- .gpio_reset = -EINVAL,
- .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static inline void __init omap3stalker_init_eth(void)
-{
- omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3stalker_init_eth(void)
-{
- return;
-}
-#endif
-
-/*
- * OMAP3 DSS control signals
- */
-
-#define DSS_ENABLE_GPIO 199
-#define LCD_PANEL_BKLIGHT_GPIO 210
-#define ENABLE_VPLL2_DEV_GRP 0xE0
-
-static void __init omap3_stalker_display_init(void)
-{
- return;
-}
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = -1,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = DSS_ENABLE_GPIO,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3stalker_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3stalker_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
- .invert_polarity = false,
-};
-
-static struct platform_device omap3stalker_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &omap3stalker_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_stalker_dss_data = {
- .default_display_name = "dvi",
-};
-
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3stalker_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vmmc1_supply),
- .consumer_supplies = omap3stalker_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data omap3stalker_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vsim_supply),
- .consumer_supplies = omap3stalker_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = 23,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 18,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "stalker:D8:usr0",
- .default_trigger = "default-on",
- .gpio = 126,
- },
- {
- .name = "stalker:D9:usr1",
- .default_trigger = "default-on",
- .gpio = 127,
- },
- {
- .name = "stalker:D3:mmc0",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "mmc0",
- },
- {
- .name = "stalker:D4:heartbeat",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "heartbeat",
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static int
-omap3stalker_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /*
- * Most GPIOs are for USB OTG. Some are mostly sent to
- * the P2 connector; notably LEDA for the LCD backlight.
- */
-
- /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
- "EN_LCD_BKL");
-
- /* gpio + 7 == DVI Enable */
- gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
- /* GPIO + 13 == ledsync (out, heartbeat) */
- gpio_leds[3].gpio = gpio + 13;
-
- platform_device_register(&leds_gpio);
- return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
- .use_leds = true,
- .setup = omap3stalker_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_DOWN),
- KEY(0, 2, KEY_ENTER),
- KEY(0, 3, KEY_M),
-
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_I),
- KEY(1, 3, KEY_N),
-
- KEY(2, 0, KEY_A),
- KEY(2, 1, KEY_E),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_O),
-
- KEY(3, 0, KEY_B),
- KEY(3, 1, KEY_F),
- KEY(3, 2, KEY_K),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3stalker_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-static struct twl4030_platform_data omap3stalker_twldata = {
- /* platform_data for children goes here */
- .keypad = &omap3stalker_kp_data,
- .gpio = &omap3stalker_gpio_data,
- .vmmc1 = &omap3stalker_vmmc1,
- .vsim = &omap3stalker_vsim,
-};
-
-static struct at24_platform_data fram_info = {
- .byte_len = (64 * 1024) / 8,
- .page_size = 8192,
- .flags = AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
- {
- I2C_BOARD_INFO("24c64", 0x50),
- .flags = I2C_CLIENT_WAKE,
- .platform_data = &fram_info,
- },
-};
-
-static int __init omap3_stalker_i2c_init(void)
-{
- omap3_pmic_get_config(&omap3stalker_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
- TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- omap3stalker_twldata.vdac->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.name = "VDVI";
-
- omap3_pmic_init("twl4030", &omap3stalker_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
- ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
- return 0;
-}
-
-#define OMAP3_STALKER_TS_GPIO 175
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = 21,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct platform_device *omap3_stalker_devices[] __initdata = {
- &keys_gpio,
- &omap3stalker_tfp410_device,
- &omap3stalker_dvi_connector_device,
- &omap3stalker_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- {.reg_offset = OMAP_MUX_TERMINATOR},
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3_stalker_init(void)
-{
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- omap_hsmmc_init(mmc);
-
- omap3_stalker_i2c_init();
-
- platform_add_devices(omap3_stalker_devices,
- ARRAY_SIZE(omap3_stalker_devices));
-
- omap_display_init(&omap3_stalker_dss_data);
-
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
-
- omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
-
- omap3stalker_init_eth();
- omap3_stalker_display_init();
-/* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(SBC3530, "OMAP3 STALKER")
- /* Maintainer: Jason Lam -lzg at ema-tech.com */
- .atag_offset = 0x100,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_stalker_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/3] ARM: OMAP3: Remove legacy support for devkit8000
2015-03-17 0:25 ` Tony Lindgren
@ 2015-03-17 0:25 ` Tony Lindgren
-1 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-omap; +Cc: linux-arm-kernel, Thomas Weber
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
http://www.embest-tech.com/product/single-board-computers/index.html
Cc: Thomas Weber <thomas@tomweber.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 1 -
arch/arm/mach-omap2/board-devkit8000.c | 654 ---------------------------------
3 files changed, 661 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-devkit8000.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 88e3eaf..559e287 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -175,12 +175,6 @@ config MACH_OMAP3_BEAGLE
default y
select OMAP_PACKAGE_CBB
-config MACH_DEVKIT8000
- bool "DEVKIT8000 board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CUS
-
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 10b9563..c346b48 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -243,7 +243,6 @@ obj-$(CONFIG_SOC_OMAP2420) += msdi.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
-obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
deleted file mode 100644
index d8e4f34..0000000
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ /dev/null
@@ -1,654 +0,0 @@
-/*
- * board-devkit8000.c - TimLL Devkit8000
- *
- * Copyright (C) 2009 Kim Botherway
- * Copyright (C) 2010 Thomas Weber
- *
- * Modified from mach-omap2/board-omap3beagle.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include "id.h"
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/dm9000.h>
-#include <linux/interrupt.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define NAND_CS 0
-
-#define OMAP_DM9000_GPIO_IRQ 25
-#define OMAP3_DEVKIT_TS_GPIO 27
-
-static struct mtd_partition devkit8000_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 15 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot Env",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
- .size = 1 * NAND_BLOCK_SIZE,
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
- .gpio_wp = 29,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct regulator_consumer_supply devkit8000_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supply[] = {
- REGULATOR_SUPPLY("vcc", "spi2.0"),
-};
-
-static const struct display_timing devkit8000_lcd_videomode = {
- .pixelclock = { 0, 40000000, 0 },
-
- .hactive = { 0, 800, 0 },
- .hfront_porch = { 0, 1, 0 },
- .hback_porch = { 0, 1, 0 },
- .hsync_len = { 0, 48, 0 },
-
- .vactive = { 0, 480, 0 },
- .vfront_porch = { 0, 12, 0 },
- .vback_porch = { 0, 25, 0 },
- .vsync_len = { 0, 3, 0 },
-
- .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
- DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data devkit8000_lcd_pdata = {
- .name = "lcd",
- .source = "dpi.0",
-
- .data_lines = 24,
-
- .display_timing = &devkit8000_lcd_videomode,
-
- .enable_gpio = -1, /* filled in code */
- .backlight_gpio = -1,
-};
-
-static struct platform_device devkit8000_lcd_device = {
- .name = "panel-dpi",
- .id = 0,
- .dev.platform_data = &devkit8000_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data devkit8000_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 1,
-};
-
-static struct platform_device devkit8000_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &devkit8000_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data devkit8000_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = -1, /* filled in code */
-};
-
-static struct platform_device devkit8000_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &devkit8000_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data devkit8000_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
- .invert_polarity = false,
-};
-
-static struct platform_device devkit8000_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &devkit8000_tv_pdata,
-};
-
-static struct omap_dss_board_info devkit8000_dss_data = {
- .default_display_name = "lcd",
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_1),
- KEY(1, 0, KEY_2),
- KEY(2, 0, KEY_3),
- KEY(0, 1, KEY_4),
- KEY(1, 1, KEY_5),
- KEY(2, 1, KEY_6),
- KEY(3, 1, KEY_F5),
- KEY(0, 2, KEY_7),
- KEY(1, 2, KEY_8),
- KEY(2, 2, KEY_9),
- KEY(3, 2, KEY_F6),
- KEY(0, 3, KEY_F7),
- KEY(1, 3, KEY_0),
- KEY(2, 3, KEY_F8),
- PERSISTENT_KEY(4, 5),
- KEY(4, 4, KEY_VOLUMEUP),
- KEY(5, 5, KEY_VOLUMEDOWN),
- 0
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data devkit8000_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 6,
- .cols = 6,
- .rep = 1,
-};
-
-static struct gpio_led gpio_leds[];
-
-static int devkit8000_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- /* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
- devkit8000_lcd_pdata.enable_gpio = gpio + TWL4030_GPIO_MAX + 0;
-
- /* gpio + 7 is "DVI_PD" (out, active low) */
- devkit8000_tfp410_pdata.power_down_gpio = gpio + 7;
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
- .use_leds = true,
- .pulldowns = BIT(1) | BIT(2) | BIT(6) | BIT(8) | BIT(13)
- | BIT(15) | BIT(16) | BIT(17),
- .setup = devkit8000_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data devkit8000_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(devkit8000_vmmc1_supply),
- .consumer_supplies = devkit8000_vmmc1_supply,
-};
-
-/* VPLL1 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll1 = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(devkit8000_vpll1_supplies),
- .consumer_supplies = devkit8000_vpll1_supplies,
-};
-
-/* VAUX4 for ads7846 and nubs */
-static struct regulator_init_data devkit8000_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(devkit8000_vio_supply),
- .consumer_supplies = devkit8000_vio_supply,
-};
-
-static struct twl4030_platform_data devkit8000_twldata = {
- /* platform_data for children goes here */
- .gpio = &devkit8000_gpio_data,
- .vmmc1 = &devkit8000_vmmc1,
- .vpll1 = &devkit8000_vpll1,
- .vio = &devkit8000_vio,
- .keypad = &devkit8000_kp_data,
-};
-
-static int __init devkit8000_i2c_init(void)
-{
- omap3_pmic_get_config(&devkit8000_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC);
- omap3_pmic_init("tps65930", &devkit8000_twldata);
- /* Bus 3 is attached to the DVI port where devices like the pico DLP
- * projector don't work reliably with 400kHz */
- omap_register_i2c_bus(3, 400, NULL, 0);
- return 0;
-}
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "led1",
- .default_trigger = "heartbeat",
- .gpio = 186,
- .active_low = true,
- },
- {
- .name = "led2",
- .default_trigger = "mmc0",
- .gpio = 163,
- .active_low = true,
- },
- {
- .name = "ledB",
- .default_trigger = "none",
- .gpio = 153,
- .active_low = true,
- },
- {
- .name = "led3",
- .default_trigger = "none",
- .gpio = 164,
- .active_low = true,
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 26,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-#define OMAP_DM9000_BASE 0x2c000000
-
-static struct resource omap_dm9000_resources[] = {
- [0] = {
- .start = OMAP_DM9000_BASE,
- .end = (OMAP_DM9000_BASE + 0x4 - 1),
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = (OMAP_DM9000_BASE + 0x400),
- .end = (OMAP_DM9000_BASE + 0x400 + 0x4 - 1),
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .flags = IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
- },
-};
-
-static struct dm9000_plat_data omap_dm9000_platdata = {
- .flags = DM9000_PLATF_16BITONLY,
-};
-
-static struct platform_device omap_dm9000_dev = {
- .name = "dm9000",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap_dm9000_resources),
- .resource = omap_dm9000_resources,
- .dev = {
- .platform_data = &omap_dm9000_platdata,
- },
-};
-
-static void __init omap_dm9000_init(void)
-{
- unsigned char *eth_addr = omap_dm9000_platdata.dev_addr;
- struct omap_die_id odi;
- int ret;
-
- ret = gpio_request_one(OMAP_DM9000_GPIO_IRQ, GPIOF_IN, "dm9000 irq");
- if (ret < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
- OMAP_DM9000_GPIO_IRQ);
- return;
- }
-
- /* init the mac address using DIE id */
- omap_get_die_id(&odi);
-
- eth_addr[0] = 0x02; /* locally administered */
- eth_addr[1] = odi.id_1 & 0xff;
- eth_addr[2] = (odi.id_0 & 0xff000000) >> 24;
- eth_addr[3] = (odi.id_0 & 0x00ff0000) >> 16;
- eth_addr[4] = (odi.id_0 & 0x0000ff00) >> 8;
- eth_addr[5] = (odi.id_0 & 0x000000ff);
-}
-
-static struct platform_device *devkit8000_devices[] __initdata = {
- &leds_gpio,
- &keys_gpio,
- &omap_dm9000_dev,
- &devkit8000_lcd_device,
- &devkit8000_tfp410_device,
- &devkit8000_dvi_connector_device,
- &devkit8000_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- /* nCS and IRQ for Devkit8000 ethernet */
- OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE0),
- OMAP3_MUX(ETK_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
- /* McSPI 2*/
- OMAP3_MUX(MCSPI2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI2_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCSPI2_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI2_CS0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCSPI2_CS1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* PENDOWN GPIO */
- OMAP3_MUX(ETK_D13, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
- /* mUSB */
- OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* USB 1 */
- OMAP3_MUX(ETK_CTL, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(ETK_D8, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D9, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D0, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D2, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D3, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D4, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D5, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D6, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D7, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-
- /* MMC 1 */
- OMAP3_MUX(SDMMC1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* McBSP 2 */
- OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* I2C 1 */
- OMAP3_MUX(I2C1_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C1_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* I2C 2 */
- OMAP3_MUX(I2C2_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C2_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* I2C 3 */
- OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* I2C 4 */
- OMAP3_MUX(I2C4_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C4_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* serial ports */
- OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* DSS */
- OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* expansion port */
- /* McSPI 1 */
- OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
- OMAP3_MUX(MCSPI1_CS3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-
- /* HDQ */
- OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* McSPI4 */
- OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
-
- /* MMC 2 */
- OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-
- /* I2C3 */
- OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- /* TPS IRQ */
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
- OMAP_PIN_INPUT_PULLUP),
-
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init devkit8000_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
-
- omap_dm9000_init();
-
- omap_hsmmc_init(mmc);
- devkit8000_i2c_init();
- omap_dm9000_resources[2].start = gpio_to_irq(OMAP_DM9000_GPIO_IRQ);
- platform_add_devices(devkit8000_devices,
- ARRAY_SIZE(devkit8000_devices));
-
- omap_display_init(&devkit8000_dss_data);
-
- omap_ads7846_init(2, OMAP3_DEVKIT_TS_GPIO, 0, NULL);
-
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
- usbhs_init(&usbhs_bdata);
- board_nand_init(devkit8000_nand_partitions,
- ARRAY_SIZE(devkit8000_nand_partitions), NAND_CS,
- NAND_BUSWIDTH_16, NULL);
- omap_twl4030_audio_init("omap3beagle", NULL);
-
- /* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = devkit8000_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/3] ARM: OMAP3: Remove legacy support for devkit8000
@ 2015-03-17 0:25 ` Tony Lindgren
0 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-arm-kernel
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
http://www.embest-tech.com/product/single-board-computers/index.html
Cc: Thomas Weber <thomas@tomweber.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 1 -
arch/arm/mach-omap2/board-devkit8000.c | 654 ---------------------------------
3 files changed, 661 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-devkit8000.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 88e3eaf..559e287 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -175,12 +175,6 @@ config MACH_OMAP3_BEAGLE
default y
select OMAP_PACKAGE_CBB
-config MACH_DEVKIT8000
- bool "DEVKIT8000 board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CUS
-
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 10b9563..c346b48 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -243,7 +243,6 @@ obj-$(CONFIG_SOC_OMAP2420) += msdi.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
-obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
deleted file mode 100644
index d8e4f34..0000000
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ /dev/null
@@ -1,654 +0,0 @@
-/*
- * board-devkit8000.c - TimLL Devkit8000
- *
- * Copyright (C) 2009 Kim Botherway
- * Copyright (C) 2010 Thomas Weber
- *
- * Modified from mach-omap2/board-omap3beagle.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include "id.h"
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/dm9000.h>
-#include <linux/interrupt.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define NAND_CS 0
-
-#define OMAP_DM9000_GPIO_IRQ 25
-#define OMAP3_DEVKIT_TS_GPIO 27
-
-static struct mtd_partition devkit8000_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 15 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot Env",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
- .size = 1 * NAND_BLOCK_SIZE,
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
- .gpio_wp = 29,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct regulator_consumer_supply devkit8000_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supply[] = {
- REGULATOR_SUPPLY("vcc", "spi2.0"),
-};
-
-static const struct display_timing devkit8000_lcd_videomode = {
- .pixelclock = { 0, 40000000, 0 },
-
- .hactive = { 0, 800, 0 },
- .hfront_porch = { 0, 1, 0 },
- .hback_porch = { 0, 1, 0 },
- .hsync_len = { 0, 48, 0 },
-
- .vactive = { 0, 480, 0 },
- .vfront_porch = { 0, 12, 0 },
- .vback_porch = { 0, 25, 0 },
- .vsync_len = { 0, 3, 0 },
-
- .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
- DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data devkit8000_lcd_pdata = {
- .name = "lcd",
- .source = "dpi.0",
-
- .data_lines = 24,
-
- .display_timing = &devkit8000_lcd_videomode,
-
- .enable_gpio = -1, /* filled in code */
- .backlight_gpio = -1,
-};
-
-static struct platform_device devkit8000_lcd_device = {
- .name = "panel-dpi",
- .id = 0,
- .dev.platform_data = &devkit8000_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data devkit8000_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 1,
-};
-
-static struct platform_device devkit8000_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &devkit8000_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data devkit8000_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = -1, /* filled in code */
-};
-
-static struct platform_device devkit8000_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &devkit8000_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data devkit8000_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
- .invert_polarity = false,
-};
-
-static struct platform_device devkit8000_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &devkit8000_tv_pdata,
-};
-
-static struct omap_dss_board_info devkit8000_dss_data = {
- .default_display_name = "lcd",
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_1),
- KEY(1, 0, KEY_2),
- KEY(2, 0, KEY_3),
- KEY(0, 1, KEY_4),
- KEY(1, 1, KEY_5),
- KEY(2, 1, KEY_6),
- KEY(3, 1, KEY_F5),
- KEY(0, 2, KEY_7),
- KEY(1, 2, KEY_8),
- KEY(2, 2, KEY_9),
- KEY(3, 2, KEY_F6),
- KEY(0, 3, KEY_F7),
- KEY(1, 3, KEY_0),
- KEY(2, 3, KEY_F8),
- PERSISTENT_KEY(4, 5),
- KEY(4, 4, KEY_VOLUMEUP),
- KEY(5, 5, KEY_VOLUMEDOWN),
- 0
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data devkit8000_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 6,
- .cols = 6,
- .rep = 1,
-};
-
-static struct gpio_led gpio_leds[];
-
-static int devkit8000_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- /* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
- devkit8000_lcd_pdata.enable_gpio = gpio + TWL4030_GPIO_MAX + 0;
-
- /* gpio + 7 is "DVI_PD" (out, active low) */
- devkit8000_tfp410_pdata.power_down_gpio = gpio + 7;
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
- .use_leds = true,
- .pulldowns = BIT(1) | BIT(2) | BIT(6) | BIT(8) | BIT(13)
- | BIT(15) | BIT(16) | BIT(17),
- .setup = devkit8000_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data devkit8000_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(devkit8000_vmmc1_supply),
- .consumer_supplies = devkit8000_vmmc1_supply,
-};
-
-/* VPLL1 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll1 = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(devkit8000_vpll1_supplies),
- .consumer_supplies = devkit8000_vpll1_supplies,
-};
-
-/* VAUX4 for ads7846 and nubs */
-static struct regulator_init_data devkit8000_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(devkit8000_vio_supply),
- .consumer_supplies = devkit8000_vio_supply,
-};
-
-static struct twl4030_platform_data devkit8000_twldata = {
- /* platform_data for children goes here */
- .gpio = &devkit8000_gpio_data,
- .vmmc1 = &devkit8000_vmmc1,
- .vpll1 = &devkit8000_vpll1,
- .vio = &devkit8000_vio,
- .keypad = &devkit8000_kp_data,
-};
-
-static int __init devkit8000_i2c_init(void)
-{
- omap3_pmic_get_config(&devkit8000_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC);
- omap3_pmic_init("tps65930", &devkit8000_twldata);
- /* Bus 3 is attached to the DVI port where devices like the pico DLP
- * projector don't work reliably with 400kHz */
- omap_register_i2c_bus(3, 400, NULL, 0);
- return 0;
-}
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "led1",
- .default_trigger = "heartbeat",
- .gpio = 186,
- .active_low = true,
- },
- {
- .name = "led2",
- .default_trigger = "mmc0",
- .gpio = 163,
- .active_low = true,
- },
- {
- .name = "ledB",
- .default_trigger = "none",
- .gpio = 153,
- .active_low = true,
- },
- {
- .name = "led3",
- .default_trigger = "none",
- .gpio = 164,
- .active_low = true,
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 26,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-#define OMAP_DM9000_BASE 0x2c000000
-
-static struct resource omap_dm9000_resources[] = {
- [0] = {
- .start = OMAP_DM9000_BASE,
- .end = (OMAP_DM9000_BASE + 0x4 - 1),
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = (OMAP_DM9000_BASE + 0x400),
- .end = (OMAP_DM9000_BASE + 0x400 + 0x4 - 1),
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .flags = IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
- },
-};
-
-static struct dm9000_plat_data omap_dm9000_platdata = {
- .flags = DM9000_PLATF_16BITONLY,
-};
-
-static struct platform_device omap_dm9000_dev = {
- .name = "dm9000",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap_dm9000_resources),
- .resource = omap_dm9000_resources,
- .dev = {
- .platform_data = &omap_dm9000_platdata,
- },
-};
-
-static void __init omap_dm9000_init(void)
-{
- unsigned char *eth_addr = omap_dm9000_platdata.dev_addr;
- struct omap_die_id odi;
- int ret;
-
- ret = gpio_request_one(OMAP_DM9000_GPIO_IRQ, GPIOF_IN, "dm9000 irq");
- if (ret < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
- OMAP_DM9000_GPIO_IRQ);
- return;
- }
-
- /* init the mac address using DIE id */
- omap_get_die_id(&odi);
-
- eth_addr[0] = 0x02; /* locally administered */
- eth_addr[1] = odi.id_1 & 0xff;
- eth_addr[2] = (odi.id_0 & 0xff000000) >> 24;
- eth_addr[3] = (odi.id_0 & 0x00ff0000) >> 16;
- eth_addr[4] = (odi.id_0 & 0x0000ff00) >> 8;
- eth_addr[5] = (odi.id_0 & 0x000000ff);
-}
-
-static struct platform_device *devkit8000_devices[] __initdata = {
- &leds_gpio,
- &keys_gpio,
- &omap_dm9000_dev,
- &devkit8000_lcd_device,
- &devkit8000_tfp410_device,
- &devkit8000_dvi_connector_device,
- &devkit8000_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- /* nCS and IRQ for Devkit8000 ethernet */
- OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE0),
- OMAP3_MUX(ETK_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
- /* McSPI 2*/
- OMAP3_MUX(MCSPI2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI2_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCSPI2_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI2_CS0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCSPI2_CS1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* PENDOWN GPIO */
- OMAP3_MUX(ETK_D13, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
- /* mUSB */
- OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* USB 1 */
- OMAP3_MUX(ETK_CTL, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(ETK_D8, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D9, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D0, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D2, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D3, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D4, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D5, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D6, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
- OMAP3_MUX(ETK_D7, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-
- /* MMC 1 */
- OMAP3_MUX(SDMMC1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(SDMMC1_DAT7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* McBSP 2 */
- OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* I2C 1 */
- OMAP3_MUX(I2C1_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C1_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* I2C 2 */
- OMAP3_MUX(I2C2_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C2_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* I2C 3 */
- OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* I2C 4 */
- OMAP3_MUX(I2C4_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C4_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* serial ports */
- OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* DSS */
- OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
- /* expansion port */
- /* McSPI 1 */
- OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
- OMAP3_MUX(MCSPI1_CS3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-
- /* HDQ */
- OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- /* McSPI4 */
- OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
- OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
-
- /* MMC 2 */
- OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-
- /* I2C3 */
- OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
- OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
- OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
- /* TPS IRQ */
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
- OMAP_PIN_INPUT_PULLUP),
-
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init devkit8000_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
-
- omap_dm9000_init();
-
- omap_hsmmc_init(mmc);
- devkit8000_i2c_init();
- omap_dm9000_resources[2].start = gpio_to_irq(OMAP_DM9000_GPIO_IRQ);
- platform_add_devices(devkit8000_devices,
- ARRAY_SIZE(devkit8000_devices));
-
- omap_display_init(&devkit8000_dss_data);
-
- omap_ads7846_init(2, OMAP3_DEVKIT_TS_GPIO, 0, NULL);
-
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
- usbhs_init(&usbhs_bdata);
- board_nand_init(devkit8000_nand_partitions,
- ARRAY_SIZE(devkit8000_nand_partitions), NAND_CS,
- NAND_BUSWIDTH_16, NULL);
- omap_twl4030_audio_init("omap3beagle", NULL);
-
- /* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = devkit8000_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 3/3] ARM: OMAP2+: Remove legacy support for omap3 TouchBook
2015-03-17 0:25 ` Tony Lindgren
@ 2015-03-17 0:25 ` Tony Lindgren
-1 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-omap; +Cc: linux-arm-kernel, Gregoire Gentil, Radek Pilar
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Cc: Gregoire Gentil <gregoire@gentil.com>
Cc: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 1 -
arch/arm/mach-omap2/board-omap3touchbook.c | 395 -----------------------------
3 files changed, 402 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-omap3touchbook.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 559e287..276a755 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -219,12 +219,6 @@ config MACH_OMAP3_PANDORA
select OMAP_PACKAGE_CBB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
-config MACH_TOUCHBOOK
- bool "OMAP3 Touch Book"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
config MACH_NOKIA_N810
bool
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index c346b48..ec002bd 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -253,7 +253,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
-obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
# Platform specific device init code
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
deleted file mode 100644
index a01993e..0000000
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3touchbook.c
- *
- * Copyright (C) 2009 Always Innovating
- *
- * Modified from mach-omap2/board-omap3beagleboard.c
- *
- * Initial code: Grégoire Gentil, Tim Yamin
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/spi/spi.h>
-
-#include <linux/spi/ads7846.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <asm/system_info.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#include <asm/setup.h>
-
-#define OMAP3_AC_GPIO 136
-#define OMAP3_TS_GPIO 162
-#define TB_BL_PWM_TIMER 9
-#define TB_KILL_POWER_GPIO 168
-
-#define NAND_CS 0
-
-static unsigned long touchbook_revision;
-
-static struct mtd_partition omap3touchbook_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 15 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot Env",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
- .size = 1 * NAND_BLOCK_SIZE,
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
- .gpio_wp = 29,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct regulator_consumer_supply touchbook_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply touchbook_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct gpio_led gpio_leds[];
-
-static int touchbook_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC");
-
- /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
- gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
- "nEN_USB_PWR");
-
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data touchbook_gpio_data = {
- .use_leds = true,
- .pullups = BIT(1),
- .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
- | BIT(15) | BIT(16) | BIT(17),
- .setup = touchbook_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply touchbook_vdac_supply[] = {
-{
- .supply = "vdac",
-},
-};
-
-static struct regulator_consumer_supply touchbook_vdvi_supply[] = {
-{
- .supply = "vdvi",
-},
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data touchbook_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(touchbook_vmmc1_supply),
- .consumer_supplies = touchbook_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data touchbook_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(touchbook_vsim_supply),
- .consumer_supplies = touchbook_vsim_supply,
-};
-
-static struct twl4030_platform_data touchbook_twldata = {
- /* platform_data for children goes here */
- .gpio = &touchbook_gpio_data,
- .vmmc1 = &touchbook_vmmc1,
- .vsim = &touchbook_vsim,
-};
-
-static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("bq27200", 0x55),
- },
-};
-
-static int __init omap3_touchbook_i2c_init(void)
-{
- /* Standard TouchBook bus */
- omap3_pmic_get_config(&touchbook_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- touchbook_twldata.vdac->num_consumer_supplies =
- ARRAY_SIZE(touchbook_vdac_supply);
- touchbook_twldata.vdac->consumer_supplies = touchbook_vdac_supply;
-
- touchbook_twldata.vpll2->constraints.name = "VDVI";
- touchbook_twldata.vpll2->num_consumer_supplies =
- ARRAY_SIZE(touchbook_vdvi_supply);
- touchbook_twldata.vpll2->consumer_supplies = touchbook_vdvi_supply;
-
- omap3_pmic_init("twl4030", &touchbook_twldata);
- /* Additional TouchBook bus */
- omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
- ARRAY_SIZE(touchBook_i2c_boardinfo));
-
- return 0;
-}
-
-static struct ads7846_platform_data ads7846_pdata = {
- .x_min = 100,
- .y_min = 265,
- .x_max = 3950,
- .y_max = 3750,
- .x_plate_ohms = 40,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 5,
- .debounce_rep = 1,
- .gpio_pendown = OMAP3_TS_GPIO,
- .keep_vref_on = 1,
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "touchbook::usr0",
- .default_trigger = "heartbeat",
- .gpio = 150,
- },
- {
- .name = "touchbook::usr1",
- .default_trigger = "mmc0",
- .gpio = 149,
- },
- {
- .name = "touchbook::pmu_stat",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 7,
- .desc = "user",
- .wakeup = 1,
- },
- {
- .code = KEY_POWER,
- .gpio = 183,
- .desc = "power",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = 147,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct platform_device *omap3_touchbook_devices[] __initdata = {
- &leds_gpio,
- &keys_gpio,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void omap3_touchbook_poweroff(void)
-{
- int pwr_off = TB_KILL_POWER_GPIO;
-
- if (gpio_request_one(pwr_off, GPIOF_OUT_INIT_LOW, "DVI reset") < 0)
- printk(KERN_ERR "Unable to get kill power GPIO\n");
-}
-
-static int __init early_touchbook_revision(char *p)
-{
- if (!p)
- return 0;
-
- return kstrtoul(p, 10, &touchbook_revision);
-}
-early_param("tbr", early_touchbook_revision);
-
-static void __init omap3_touchbook_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
- pm_power_off = omap3_touchbook_poweroff;
-
- if (system_rev >= 0x20 && system_rev <= 0x34301000) {
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- mmc[0].gpio_wp = 23;
- } else {
- omap_mux_init_gpio(29, OMAP_PIN_INPUT);
- }
- omap_hsmmc_init(mmc);
-
- omap3_touchbook_i2c_init();
- platform_add_devices(omap3_touchbook_devices,
- ARRAY_SIZE(omap3_touchbook_devices));
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
-
- omap_mux_init_gpio(170, OMAP_PIN_INPUT);
- /* REVISIT leave DVI powered down until it's needed ... */
- gpio_request_one(176, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
- /* Touchscreen and accelerometer */
- omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- board_nand_init(omap3touchbook_nand_partitions,
- ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS,
- NAND_BUSWIDTH_16, NULL);
-
- /* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
- /* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3430_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_touchbook_init,
- .init_late = omap3430_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 3/3] ARM: OMAP2+: Remove legacy support for omap3 TouchBook
@ 2015-03-17 0:25 ` Tony Lindgren
0 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-17 0:25 UTC (permalink / raw)
To: linux-arm-kernel
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
As it seems this board only has minimal support upstreamed for the
legacy booting and has not seen activity for on the mailing lists
for a few years, let's attempt to remove the related legacy board-*.c
file.
I do not have this board, but it seems getting the same level of
support with device tree based booting is mostly just configuring
the .dts file. And there is no need to upgrade the boot loader as
we can boot with appended DTB too. And most of the omap3 boards
seem to be related to omap3-evm, and omap3beagleboard that are
supported with device tree based booting.
If somebody is using this board actively with the mainline kernel,
please communicate this to the linux-omap mailing list so we can
get the board booting with device tree based support. I can help
some too getting the minimal device tree based booting going if
help is needed.
The reason for attempting to remove this board now is that I'd
rather get the remaining omap3 legacy booting support into a known
state where we at least have a .dts file being written for the
remaining legacy boards. That is because for the next few merge
cycles we can still revert this patch if absolutely necessary,
but I'd rather not get suprised by missing .dts files at the point
where we are ready to drop all remaining omap3 legacy booting
support later on.
Cc: Gregoire Gentil <gregoire@gentil.com>
Cc: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 1 -
arch/arm/mach-omap2/board-omap3touchbook.c | 395 -----------------------------
3 files changed, 402 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-omap3touchbook.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 559e287..276a755 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -219,12 +219,6 @@ config MACH_OMAP3_PANDORA
select OMAP_PACKAGE_CBB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
-config MACH_TOUCHBOOK
- bool "OMAP3 Touch Book"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
config MACH_NOKIA_N810
bool
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index c346b48..ec002bd 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -253,7 +253,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
-obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
# Platform specific device init code
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
deleted file mode 100644
index a01993e..0000000
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3touchbook.c
- *
- * Copyright (C) 2009 Always Innovating
- *
- * Modified from mach-omap2/board-omap3beagleboard.c
- *
- * Initial code: Gr?goire Gentil, Tim Yamin
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/spi/spi.h>
-
-#include <linux/spi/ads7846.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <asm/system_info.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#include <asm/setup.h>
-
-#define OMAP3_AC_GPIO 136
-#define OMAP3_TS_GPIO 162
-#define TB_BL_PWM_TIMER 9
-#define TB_KILL_POWER_GPIO 168
-
-#define NAND_CS 0
-
-static unsigned long touchbook_revision;
-
-static struct mtd_partition omap3touchbook_nand_partitions[] = {
- /* All the partition sizes are listed in terms of NAND block size */
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 4 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
- .size = 15 * NAND_BLOCK_SIZE,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- },
- {
- .name = "U-Boot Env",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
- .size = 1 * NAND_BLOCK_SIZE,
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
- .size = 32 * NAND_BLOCK_SIZE,
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
- .gpio_wp = 29,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct regulator_consumer_supply touchbook_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply touchbook_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct gpio_led gpio_leds[];
-
-static int touchbook_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC");
-
- /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
- gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
- "nEN_USB_PWR");
-
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- return 0;
-}
-
-static struct twl4030_gpio_platform_data touchbook_gpio_data = {
- .use_leds = true,
- .pullups = BIT(1),
- .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
- | BIT(15) | BIT(16) | BIT(17),
- .setup = touchbook_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply touchbook_vdac_supply[] = {
-{
- .supply = "vdac",
-},
-};
-
-static struct regulator_consumer_supply touchbook_vdvi_supply[] = {
-{
- .supply = "vdvi",
-},
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data touchbook_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(touchbook_vmmc1_supply),
- .consumer_supplies = touchbook_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data touchbook_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(touchbook_vsim_supply),
- .consumer_supplies = touchbook_vsim_supply,
-};
-
-static struct twl4030_platform_data touchbook_twldata = {
- /* platform_data for children goes here */
- .gpio = &touchbook_gpio_data,
- .vmmc1 = &touchbook_vmmc1,
- .vsim = &touchbook_vsim,
-};
-
-static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("bq27200", 0x55),
- },
-};
-
-static int __init omap3_touchbook_i2c_init(void)
-{
- /* Standard TouchBook bus */
- omap3_pmic_get_config(&touchbook_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
- touchbook_twldata.vdac->num_consumer_supplies =
- ARRAY_SIZE(touchbook_vdac_supply);
- touchbook_twldata.vdac->consumer_supplies = touchbook_vdac_supply;
-
- touchbook_twldata.vpll2->constraints.name = "VDVI";
- touchbook_twldata.vpll2->num_consumer_supplies =
- ARRAY_SIZE(touchbook_vdvi_supply);
- touchbook_twldata.vpll2->consumer_supplies = touchbook_vdvi_supply;
-
- omap3_pmic_init("twl4030", &touchbook_twldata);
- /* Additional TouchBook bus */
- omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
- ARRAY_SIZE(touchBook_i2c_boardinfo));
-
- return 0;
-}
-
-static struct ads7846_platform_data ads7846_pdata = {
- .x_min = 100,
- .y_min = 265,
- .x_max = 3950,
- .y_max = 3750,
- .x_plate_ohms = 40,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 5,
- .debounce_rep = 1,
- .gpio_pendown = OMAP3_TS_GPIO,
- .keep_vref_on = 1,
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "touchbook::usr0",
- .default_trigger = "heartbeat",
- .gpio = 150,
- },
- {
- .name = "touchbook::usr1",
- .default_trigger = "mmc0",
- .gpio = 149,
- },
- {
- .name = "touchbook::pmu_stat",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 7,
- .desc = "user",
- .wakeup = 1,
- },
- {
- .code = KEY_POWER,
- .gpio = 183,
- .desc = "power",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = 147,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct platform_device *omap3_touchbook_devices[] __initdata = {
- &leds_gpio,
- &keys_gpio,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void omap3_touchbook_poweroff(void)
-{
- int pwr_off = TB_KILL_POWER_GPIO;
-
- if (gpio_request_one(pwr_off, GPIOF_OUT_INIT_LOW, "DVI reset") < 0)
- printk(KERN_ERR "Unable to get kill power GPIO\n");
-}
-
-static int __init early_touchbook_revision(char *p)
-{
- if (!p)
- return 0;
-
- return kstrtoul(p, 10, &touchbook_revision);
-}
-early_param("tbr", early_touchbook_revision);
-
-static void __init omap3_touchbook_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
- pm_power_off = omap3_touchbook_poweroff;
-
- if (system_rev >= 0x20 && system_rev <= 0x34301000) {
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- mmc[0].gpio_wp = 23;
- } else {
- omap_mux_init_gpio(29, OMAP_PIN_INPUT);
- }
- omap_hsmmc_init(mmc);
-
- omap3_touchbook_i2c_init();
- platform_add_devices(omap3_touchbook_devices,
- ARRAY_SIZE(omap3_touchbook_devices));
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params,
- mt46h32m32lf6_sdrc_params);
-
- omap_mux_init_gpio(170, OMAP_PIN_INPUT);
- /* REVISIT leave DVI powered down until it's needed ... */
- gpio_request_one(176, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
- /* Touchscreen and accelerometer */
- omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- board_nand_init(omap3touchbook_nand_partitions,
- ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS,
- NAND_BUSWIDTH_16, NULL);
-
- /* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
- /* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap3430_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_touchbook_init,
- .init_late = omap3430_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* RE: [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
2015-03-17 0:25 ` Tony Lindgren
@ 2015-03-18 7:56 ` Jason
-1 siblings, 0 replies; 12+ messages in thread
From: Jason @ 2015-03-18 7:56 UTC (permalink / raw)
To: 'Tony Lindgren', linux-omap; +Cc: linux-arm-kernel
Hi Tony,
I think it's good to remove this legacy code.
Will let u know once I got the booting dst.
Best regards,
Jason Lam
Embedded Machine Technology Co., Ltd
Tel: +86-020-87643879-830
Fax: +86-020-87245492
Mobile: +86-13828455425
Email: lzg@ema-tech.com
Website: http://www.ema-tech.com
-----Original Message-----
From: Tony Lindgren [mailto:tony@atomide.com]
Sent: Tuesday, March 17, 2015 8:25 AM
To: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org; Jason Lam
Subject: [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker
board
We've been moving all omap2+ based systems to boot in device tree only mode
for a few years now. Only omap3 has legacy booting support remaining. Most
omap3 boards already have related arch/arm/boot/*.dts* files for booting
with device tree.
As it seems this board only has minimal support upstreamed for the legacy
booting and has not seen activity for on the mailing lists for a few years,
let's attempt to remove the related legacy board-*.c file.
I do not have this board, but it seems getting the same level of support
with device tree based booting is mostly just configuring the .dts file. And
there is no need to upgrade the boot loader as we can boot with appended DTB
too. And most of the omap3 boards seem to be related to omap3-evm, and
omap3beagleboard that are supported with device tree based booting.
If somebody is using this board actively with the mainline kernel, please
communicate this to the linux-omap mailing list so we can get the board
booting with device tree based support. I can help some too getting the
minimal device tree based booting going if help is needed.
The reason for attempting to remove this board now is that I'd rather get
the remaining omap3 legacy booting support into a known state where we at
least have a .dts file being written for the remaining legacy boards. That
is because for the next few merge cycles we can still revert this patch if
absolutely necessary, but I'd rather not get suprised by missing .dts files
at the point where we are ready to drop all remaining omap3 legacy booting
support later on.
Also looks like this board is no longer listed on ema-tech.com product page
at:
http://ema-tech.com/en/categories.html
Cc: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 2 -
arch/arm/mach-omap2/board-omap3stalker.c | 433
-------------------------------
3 files changed, 441 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-omap3stalker.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index
2b8e477..88e3eaf 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -260,12 +260,6 @@ config MACH_CM_T35
config MACH_CM_T3730
bool
-config MACH_SBC3530
- bool "OMAP3 SBC STALKER board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CUS
-
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b83f18f..10b9563 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -256,8 +256,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) +=
board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
-obj-$(CONFIG_MACH_SBC3530) += board-omap3stalker.o
-
# Platform specific device init code
omap-flash-$(CONFIG_MTD_NAND_OMAP2) := board-flash.o
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c
b/arch/arm/mach-omap2/board-omap3stalker.c
deleted file mode 100644
index 6311f4b..0000000
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Guangzhou EMA-Tech
- *
- * Modified from mach-omap2/board-omap3evm.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/platform_data/at24.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) -#include
"gpmc-smsc911x.h"
-
-#define OMAP3STALKER_ETHR_START 0x2c000000
-#define OMAP3STALKER_ETHR_SIZE 1024
-#define OMAP3STALKER_ETHR_GPIO_IRQ 19
-#define OMAP3STALKER_SMC911X_CS 5
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = OMAP3STALKER_SMC911X_CS,
- .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
- .gpio_reset = -EINVAL,
- .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static inline void __init omap3stalker_init_eth(void) -{
- omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3stalker_init_eth(void) -{
- return;
-}
-#endif
-
-/*
- * OMAP3 DSS control signals
- */
-
-#define DSS_ENABLE_GPIO 199
-#define LCD_PANEL_BKLIGHT_GPIO 210
-#define ENABLE_VPLL2_DEV_GRP 0xE0
-
-static void __init omap3_stalker_display_init(void) -{
- return;
-}
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata
= {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = -1,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = DSS_ENABLE_GPIO,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3stalker_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3stalker_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
- .invert_polarity = false,
-};
-
-static struct platform_device omap3stalker_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &omap3stalker_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_stalker_dss_data = {
- .default_display_name = "dvi",
-};
-
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220
mA) */ -static struct regulator_init_data omap3stalker_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vmmc1_supply),
- .consumer_supplies = omap3stalker_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ -static
struct regulator_init_data omap3stalker_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vsim_supply),
- .consumer_supplies = omap3stalker_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = 23,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 18,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "stalker:D8:usr0",
- .default_trigger = "default-on",
- .gpio = 126,
- },
- {
- .name = "stalker:D9:usr1",
- .default_trigger = "default-on",
- .gpio = 127,
- },
- {
- .name = "stalker:D3:mmc0",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "mmc0",
- },
- {
- .name = "stalker:D4:heartbeat",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "heartbeat",
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static int
-omap3stalker_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /*
- * Most GPIOs are for USB OTG. Some are mostly sent to
- * the P2 connector; notably LEDA for the LCD backlight.
- */
-
- /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
- "EN_LCD_BKL");
-
- /* gpio + 7 == DVI Enable */
- gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
- /* GPIO + 13 == ledsync (out, heartbeat) */
- gpio_leds[3].gpio = gpio + 13;
-
- platform_device_register(&leds_gpio);
- return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
- .use_leds = true,
- .setup = omap3stalker_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_DOWN),
- KEY(0, 2, KEY_ENTER),
- KEY(0, 3, KEY_M),
-
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_I),
- KEY(1, 3, KEY_N),
-
- KEY(2, 0, KEY_A),
- KEY(2, 1, KEY_E),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_O),
-
- KEY(3, 0, KEY_B),
- KEY(3, 1, KEY_F),
- KEY(3, 2, KEY_K),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3stalker_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-static struct twl4030_platform_data omap3stalker_twldata = {
- /* platform_data for children goes here */
- .keypad = &omap3stalker_kp_data,
- .gpio = &omap3stalker_gpio_data,
- .vmmc1 = &omap3stalker_vmmc1,
- .vsim = &omap3stalker_vsim,
-};
-
-static struct at24_platform_data fram_info = {
- .byte_len = (64 * 1024) / 8,
- .page_size = 8192,
- .flags = AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
- {
- I2C_BOARD_INFO("24c64", 0x50),
- .flags = I2C_CLIENT_WAKE,
- .platform_data = &fram_info,
- },
-};
-
-static int __init omap3_stalker_i2c_init(void) -{
- omap3_pmic_get_config(&omap3stalker_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
- TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC |
TWL_COMMON_REGULATOR_VPLL2);
-
- omap3stalker_twldata.vdac->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.name = "VDVI";
-
- omap3_pmic_init("twl4030", &omap3stalker_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
- ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
- return 0;
-}
-
-#define OMAP3_STALKER_TS_GPIO 175
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = 21,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct platform_device *omap3_stalker_devices[] __initdata = {
- &keys_gpio,
- &omap3stalker_tfp410_device,
- &omap3stalker_dvi_connector_device,
- &omap3stalker_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- {.reg_offset = OMAP_MUX_TERMINATOR},
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3_stalker_init(void) -{
- regulator_register_fixed(0, dummy_supplies,
ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- omap_hsmmc_init(mmc);
-
- omap3_stalker_i2c_init();
-
- platform_add_devices(omap3_stalker_devices,
- ARRAY_SIZE(omap3_stalker_devices));
-
- omap_display_init(&omap3_stalker_dss_data);
-
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
-
- omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
-
- omap3stalker_init_eth();
- omap3_stalker_display_init();
-/* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(SBC3530, "OMAP3 STALKER")
- /* Maintainer: Jason Lam -lzg@ema-tech.com */
- .atag_offset = 0x100,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_stalker_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
@ 2015-03-18 7:56 ` Jason
0 siblings, 0 replies; 12+ messages in thread
From: Jason @ 2015-03-18 7:56 UTC (permalink / raw)
To: linux-arm-kernel
Hi Tony,
I think it's good to remove this legacy code.
Will let u know once I got the booting dst.
Best regards,
Jason Lam
Embedded Machine Technology Co., Ltd
Tel: +86-020-87643879-830
Fax: +86-020-87245492
Mobile: +86-13828455425
Email: lzg at ema-tech.com
Website: http://www.ema-tech.com
-----Original Message-----
From: Tony Lindgren [mailto:tony at atomide.com]
Sent: Tuesday, March 17, 2015 8:25 AM
To: linux-omap at vger.kernel.org
Cc: linux-arm-kernel at lists.infradead.org; Jason Lam
Subject: [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker
board
We've been moving all omap2+ based systems to boot in device tree only mode
for a few years now. Only omap3 has legacy booting support remaining. Most
omap3 boards already have related arch/arm/boot/*.dts* files for booting
with device tree.
As it seems this board only has minimal support upstreamed for the legacy
booting and has not seen activity for on the mailing lists for a few years,
let's attempt to remove the related legacy board-*.c file.
I do not have this board, but it seems getting the same level of support
with device tree based booting is mostly just configuring the .dts file. And
there is no need to upgrade the boot loader as we can boot with appended DTB
too. And most of the omap3 boards seem to be related to omap3-evm, and
omap3beagleboard that are supported with device tree based booting.
If somebody is using this board actively with the mainline kernel, please
communicate this to the linux-omap mailing list so we can get the board
booting with device tree based support. I can help some too getting the
minimal device tree based booting going if help is needed.
The reason for attempting to remove this board now is that I'd rather get
the remaining omap3 legacy booting support into a known state where we at
least have a .dts file being written for the remaining legacy boards. That
is because for the next few merge cycles we can still revert this patch if
absolutely necessary, but I'd rather not get suprised by missing .dts files
at the point where we are ready to drop all remaining omap3 legacy booting
support later on.
Also looks like this board is no longer listed on ema-tech.com product page
at:
http://ema-tech.com/en/categories.html
Cc: Jason Lam <lzg@ema-tech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 6 -
arch/arm/mach-omap2/Makefile | 2 -
arch/arm/mach-omap2/board-omap3stalker.c | 433
-------------------------------
3 files changed, 441 deletions(-)
delete mode 100644 arch/arm/mach-omap2/board-omap3stalker.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index
2b8e477..88e3eaf 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -260,12 +260,6 @@ config MACH_CM_T35
config MACH_CM_T3730
bool
-config MACH_SBC3530
- bool "OMAP3 SBC STALKER board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CUS
-
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b83f18f..10b9563 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -256,8 +256,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) +=
board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
-obj-$(CONFIG_MACH_SBC3530) += board-omap3stalker.o
-
# Platform specific device init code
omap-flash-$(CONFIG_MTD_NAND_OMAP2) := board-flash.o
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c
b/arch/arm/mach-omap2/board-omap3stalker.c
deleted file mode 100644
index 6311f4b..0000000
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Guangzhou EMA-Tech
- *
- * Modified from mach-omap2/board-omap3evm.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/platform_data/at24.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) -#include
"gpmc-smsc911x.h"
-
-#define OMAP3STALKER_ETHR_START 0x2c000000
-#define OMAP3STALKER_ETHR_SIZE 1024
-#define OMAP3STALKER_ETHR_GPIO_IRQ 19
-#define OMAP3STALKER_SMC911X_CS 5
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = OMAP3STALKER_SMC911X_CS,
- .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
- .gpio_reset = -EINVAL,
- .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static inline void __init omap3stalker_init_eth(void) -{
- omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3stalker_init_eth(void) -{
- return;
-}
-#endif
-
-/*
- * OMAP3 DSS control signals
- */
-
-#define DSS_ENABLE_GPIO 199
-#define LCD_PANEL_BKLIGHT_GPIO 210
-#define ENABLE_VPLL2_DEV_GRP 0xE0
-
-static void __init omap3_stalker_display_init(void) -{
- return;
-}
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata
= {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = -1,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = DSS_ENABLE_GPIO,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3stalker_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3stalker_tv_pdata = {
- .name = "tv",
- .source = "venc.0",
- .connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
- .invert_polarity = false,
-};
-
-static struct platform_device omap3stalker_tv_connector_device = {
- .name = "connector-analog-tv",
- .id = 0,
- .dev.platform_data = &omap3stalker_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_stalker_dss_data = {
- .default_display_name = "dvi",
-};
-
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220
mA) */ -static struct regulator_init_data omap3stalker_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vmmc1_supply),
- .consumer_supplies = omap3stalker_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ -static
struct regulator_init_data omap3stalker_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vsim_supply),
- .consumer_supplies = omap3stalker_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = 23,
- .deferred = true,
- },
- {} /* Terminator */
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
- {
- .code = BTN_EXTRA,
- .gpio = 18,
- .desc = "user",
- .wakeup = 1,
- },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-static struct gpio_led gpio_leds[] = {
- {
- .name = "stalker:D8:usr0",
- .default_trigger = "default-on",
- .gpio = 126,
- },
- {
- .name = "stalker:D9:usr1",
- .default_trigger = "default-on",
- .gpio = 127,
- },
- {
- .name = "stalker:D3:mmc0",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "mmc0",
- },
- {
- .name = "stalker:D4:heartbeat",
- .gpio = -EINVAL, /* gets replaced */
- .active_low = true,
- .default_trigger = "heartbeat",
- },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &gpio_led_info,
- },
-};
-
-static int
-omap3stalker_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /*
- * Most GPIOs are for USB OTG. Some are mostly sent to
- * the P2 connector; notably LEDA for the LCD backlight.
- */
-
- /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
- "EN_LCD_BKL");
-
- /* gpio + 7 == DVI Enable */
- gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
- /* GPIO + 13 == ledsync (out, heartbeat) */
- gpio_leds[3].gpio = gpio + 13;
-
- platform_device_register(&leds_gpio);
- return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
- .use_leds = true,
- .setup = omap3stalker_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_DOWN),
- KEY(0, 2, KEY_ENTER),
- KEY(0, 3, KEY_M),
-
- KEY(1, 0, KEY_RIGHT),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_I),
- KEY(1, 3, KEY_N),
-
- KEY(2, 0, KEY_A),
- KEY(2, 1, KEY_E),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_O),
-
- KEY(3, 0, KEY_B),
- KEY(3, 1, KEY_F),
- KEY(3, 2, KEY_K),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
- .keymap = board_keymap,
- .keymap_size = ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3stalker_kp_data = {
- .keymap_data = &board_map_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-static struct twl4030_platform_data omap3stalker_twldata = {
- /* platform_data for children goes here */
- .keypad = &omap3stalker_kp_data,
- .gpio = &omap3stalker_gpio_data,
- .vmmc1 = &omap3stalker_vmmc1,
- .vsim = &omap3stalker_vsim,
-};
-
-static struct at24_platform_data fram_info = {
- .byte_len = (64 * 1024) / 8,
- .page_size = 8192,
- .flags = AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
- {
- I2C_BOARD_INFO("24c64", 0x50),
- .flags = I2C_CLIENT_WAKE,
- .platform_data = &fram_info,
- },
-};
-
-static int __init omap3_stalker_i2c_init(void) -{
- omap3_pmic_get_config(&omap3stalker_twldata,
- TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
- TWL_COMMON_PDATA_AUDIO,
- TWL_COMMON_REGULATOR_VDAC |
TWL_COMMON_REGULATOR_VPLL2);
-
- omap3stalker_twldata.vdac->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.apply_uV = true;
- omap3stalker_twldata.vpll2->constraints.name = "VDVI";
-
- omap3_pmic_init("twl4030", &omap3stalker_twldata);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
- ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
- return 0;
-}
-
-#define OMAP3_STALKER_TS_GPIO 175
-
-static struct usbhs_phy_data phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = 21,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct platform_device *omap3_stalker_devices[] __initdata = {
- &keys_gpio,
- &omap3stalker_tfp410_device,
- &omap3stalker_dvi_connector_device,
- &omap3stalker_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
- {.reg_offset = OMAP_MUX_TERMINATOR},
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3_stalker_init(void) -{
- regulator_register_fixed(0, dummy_supplies,
ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- omap_hsmmc_init(mmc);
-
- omap3_stalker_i2c_init();
-
- platform_add_devices(omap3_stalker_devices,
- ARRAY_SIZE(omap3_stalker_devices));
-
- omap_display_init(&omap3_stalker_dss_data);
-
- omap_serial_init();
- omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
- usbhs_init(&usbhs_bdata);
- omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
-
- omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
-
- omap3stalker_init_eth();
- omap3_stalker_display_init();
-/* Ensure SDRC pins are mux'd for self-refresh */
- omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
- omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(SBC3530, "OMAP3 STALKER")
- /* Maintainer: Jason Lam -lzg at ema-tech.com */
- .atag_offset = 0x100,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .init_machine = omap3_stalker_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_secure_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
--
2.1.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
2015-03-18 7:56 ` Jason
@ 2015-03-18 17:41 ` Tony Lindgren
-1 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-18 17:41 UTC (permalink / raw)
To: Jason; +Cc: linux-omap, linux-arm-kernel
* Jason <lzg@ema-tech.com> [150318 00:59]:
> Hi Tony,
> I think it's good to remove this legacy code.
> Will let u know once I got the booting dst.
OK I'm planning to queue it for v4.1 merge window then unless
we hear from people using it.
Regards,
Tony
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
@ 2015-03-18 17:41 ` Tony Lindgren
0 siblings, 0 replies; 12+ messages in thread
From: Tony Lindgren @ 2015-03-18 17:41 UTC (permalink / raw)
To: linux-arm-kernel
* Jason <lzg@ema-tech.com> [150318 00:59]:
> Hi Tony,
> I think it's good to remove this legacy code.
> Will let u know once I got the booting dst.
OK I'm planning to queue it for v4.1 merge window then unless
we hear from people using it.
Regards,
Tony
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2015-03-18 17:45 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-03-17 0:25 [PATCH 0/3] Remove few inactive omap3 legacy board-*.c files Tony Lindgren
2015-03-17 0:25 ` Tony Lindgren
2015-03-17 0:25 ` [PATCH 1/3] ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board Tony Lindgren
2015-03-17 0:25 ` Tony Lindgren
2015-03-18 7:56 ` Jason
2015-03-18 7:56 ` Jason
2015-03-18 17:41 ` Tony Lindgren
2015-03-18 17:41 ` Tony Lindgren
2015-03-17 0:25 ` [PATCH 2/3] ARM: OMAP3: Remove legacy support for devkit8000 Tony Lindgren
2015-03-17 0:25 ` Tony Lindgren
2015-03-17 0:25 ` [PATCH 3/3] ARM: OMAP2+: Remove legacy support for omap3 TouchBook Tony Lindgren
2015-03-17 0:25 ` Tony Lindgren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.