* [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
Hi,
The phandle notation reduces possible mistakes when overriding nodes
by child board files and reduces duplication of addresses.
The patchset refactors Exynos5 boards to use the phandle way.
Tested by comparison of decompiled DTB for each commit.
Patchset depends (to reduce conflicts) on following patches:
1. v2: ARM: dts: Enable S3C RTC on Trats2 and Arndale Octa
http://www.spinics.net/lists/arm-kernel/msg410429.html
2. ARM: dts: Fix pinctrl settings for S2MPS11 RTC alarm IRQ on Arndale Octa
http://www.spinics.net/lists/linux-samsung-soc/msg43435.html
Best regards,
Krzysztof
Krzysztof Kozlowski (7):
ARM: dts: Add labels to nodes used in Exynos5 based DTS
ARM: dts: Use phandle notation for overriding nodes in Exynos5250
ARM: dts: Remove duplicated I2C 7 nodes in Snow
ARM: dts: Use phandle notation for overriding nodes in Arndale Octa
ARM: dts: Use phandle notation for overriding nodes in Exynos5420
ARM: dts: Use phandle notation for overriding nodes in SMDK5420
ARM: dts: Use phandle notation for overriding nodes in Exynos5440
boards
arch/arm/boot/dts/exynos5.dtsi | 6 +-
arch/arm/boot/dts/exynos5250-snow.dts | 46 +-
arch/arm/boot/dts/exynos5250.dtsi | 82 ++--
arch/arm/boot/dts/exynos5420-arndale-octa.dts | 634 ++++++++++++-------------
arch/arm/boot/dts/exynos5420-peach-pit.dts | 2 +-
arch/arm/boot/dts/exynos5420-smdk5420.dts | 639 +++++++++++++-------------
arch/arm/boot/dts/exynos5420.dtsi | 80 ++--
arch/arm/boot/dts/exynos5440-sd5v1.dts | 10 +-
arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 ++--
arch/arm/boot/dts/exynos5440.dtsi | 4 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 2 +-
11 files changed, 794 insertions(+), 796 deletions(-)
--
2.1.0
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
The phandle notation reduces possible mistakes when overriding nodes
by child board files and reduces duplication of addresses.
The patchset refactors Exynos5 boards to use the phandle way.
Tested by comparison of decompiled DTB for each commit.
Patchset depends (to reduce conflicts) on following patches:
1. v2: ARM: dts: Enable S3C RTC on Trats2 and Arndale Octa
http://www.spinics.net/lists/arm-kernel/msg410429.html
2. ARM: dts: Fix pinctrl settings for S2MPS11 RTC alarm IRQ on Arndale Octa
http://www.spinics.net/lists/linux-samsung-soc/msg43435.html
Best regards,
Krzysztof
Krzysztof Kozlowski (7):
ARM: dts: Add labels to nodes used in Exynos5 based DTS
ARM: dts: Use phandle notation for overriding nodes in Exynos5250
ARM: dts: Remove duplicated I2C 7 nodes in Snow
ARM: dts: Use phandle notation for overriding nodes in Arndale Octa
ARM: dts: Use phandle notation for overriding nodes in Exynos5420
ARM: dts: Use phandle notation for overriding nodes in SMDK5420
ARM: dts: Use phandle notation for overriding nodes in Exynos5440
boards
arch/arm/boot/dts/exynos5.dtsi | 6 +-
arch/arm/boot/dts/exynos5250-snow.dts | 46 +-
arch/arm/boot/dts/exynos5250.dtsi | 82 ++--
arch/arm/boot/dts/exynos5420-arndale-octa.dts | 634 ++++++++++++-------------
arch/arm/boot/dts/exynos5420-peach-pit.dts | 2 +-
arch/arm/boot/dts/exynos5420-smdk5420.dts | 639 +++++++++++++-------------
arch/arm/boot/dts/exynos5420.dtsi | 80 ++--
arch/arm/boot/dts/exynos5440-sd5v1.dts | 10 +-
arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 ++--
arch/arm/boot/dts/exynos5440.dtsi | 4 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 2 +-
11 files changed, 794 insertions(+), 796 deletions(-)
--
2.1.0
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 1/7] ARM: dts: Add labels to nodes used in Exynos5 based DTS
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5.dtsi | 6 +++---
arch/arm/boot/dts/exynos5440.dtsi | 4 ++--
2 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
index 056251599c69..e0f00bde7b14 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/exynos5.dtsi
@@ -81,14 +81,14 @@
interrupts = <0 54 0>;
};
- rtc@101E0000 {
+ rtc: rtc@101E0000 {
compatible = "samsung,s3c6410-rtc";
reg = <0x101E0000 0x100>;
interrupts = <0 43 0>, <0 44 0>;
status = "disabled";
};
- fimd@14400000 {
+ fimd: fimd@14400000 {
compatible = "samsung,exynos5250-fimd";
interrupt-parent = <&combiner>;
reg = <0x14400000 0x40000>;
@@ -98,7 +98,7 @@
status = "disabled";
};
- dp-controller@145B0000 {
+ dp: dp-controller@145B0000 {
compatible = "samsung,exynos5-dp";
reg = <0x145B0000 0x1000>;
interrupts = <10 3>;
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index 59d9416b3b03..f18b51f2eeaa 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -279,7 +279,7 @@
clock-names = "usbhost";
};
- pcie@290000 {
+ pcie_0: pcie@290000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x290000 0x1000
0x270000 0x1000
@@ -300,7 +300,7 @@
status = "disabled";
};
- pcie@2a0000 {
+ pcie_1: pcie@2a0000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x2a0000 0x1000
0x272000 0x1000
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 1/7] ARM: dts: Add labels to nodes used in Exynos5 based DTS
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5.dtsi | 6 +++---
arch/arm/boot/dts/exynos5440.dtsi | 4 ++--
2 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
index 056251599c69..e0f00bde7b14 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/exynos5.dtsi
@@ -81,14 +81,14 @@
interrupts = <0 54 0>;
};
- rtc at 101E0000 {
+ rtc: rtc at 101E0000 {
compatible = "samsung,s3c6410-rtc";
reg = <0x101E0000 0x100>;
interrupts = <0 43 0>, <0 44 0>;
status = "disabled";
};
- fimd at 14400000 {
+ fimd: fimd at 14400000 {
compatible = "samsung,exynos5250-fimd";
interrupt-parent = <&combiner>;
reg = <0x14400000 0x40000>;
@@ -98,7 +98,7 @@
status = "disabled";
};
- dp-controller at 145B0000 {
+ dp: dp-controller at 145B0000 {
compatible = "samsung,exynos5-dp";
reg = <0x145B0000 0x1000>;
interrupts = <10 3>;
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index 59d9416b3b03..f18b51f2eeaa 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -279,7 +279,7 @@
clock-names = "usbhost";
};
- pcie at 290000 {
+ pcie_0: pcie at 290000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x290000 0x1000
0x270000 0x1000
@@ -300,7 +300,7 @@
status = "disabled";
};
- pcie at 2a0000 {
+ pcie_1: pcie@2a0000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x2a0000 0x1000
0x272000 0x1000
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 2/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5250
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5250.dtsi | 82 +++++++++++++++++++--------------------
1 file changed, 41 insertions(+), 41 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 77f656eb8e6b..4bd737ead680 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -241,13 +241,6 @@
clock-names = "mfc";
};
- rtc: rtc@101E0000 {
- clocks = <&clock CLK_RTC>;
- clock-names = "rtc";
- interrupt-parent = <&pmu_system_controller>;
- status = "disabled";
- };
-
tmu: tmu@10060000 {
compatible = "samsung,exynos5250-tmu";
reg = <0x10060000 0x100>;
@@ -276,26 +269,6 @@
};
};
- serial@12C00000 {
- clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- serial@12C10000 {
- clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- serial@12C20000 {
- clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- serial@12C30000 {
- clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
sata: sata@122F0000 {
compatible = "snps,dwc-ahci";
samsung,sata-freq = <66>;
@@ -778,20 +751,6 @@
#phy-cells = <0>;
};
- dp: dp-controller@145B0000 {
- power-domains = <&pd_disp1>;
- clocks = <&clock CLK_DP>;
- clock-names = "dp";
- phys = <&dp_phy>;
- phy-names = "dp";
- };
-
- fimd: fimd@14400000 {
- power-domains = <&pd_disp1>;
- clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
- clock-names = "sclk_fimd", "fimd";
- };
-
adc: adc@12D10000 {
compatible = "samsung,exynos-adc-v1";
reg = <0x12D10000 0x100>;
@@ -812,3 +771,44 @@
clock-names = "secss";
};
};
+
+&dp {
+ power-domains = <&pd_disp1>;
+ clocks = <&clock CLK_DP>;
+ clock-names = "dp";
+ phys = <&dp_phy>;
+ phy-names = "dp";
+};
+
+&fimd {
+ power-domains = <&pd_disp1>;
+ clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
+ clock-names = "sclk_fimd", "fimd";
+};
+
+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
+&serial_0 {
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+ clock-names = "uart", "clk_uart_baud0";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 2/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5250
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5250.dtsi | 82 +++++++++++++++++++--------------------
1 file changed, 41 insertions(+), 41 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 77f656eb8e6b..4bd737ead680 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -241,13 +241,6 @@
clock-names = "mfc";
};
- rtc: rtc at 101E0000 {
- clocks = <&clock CLK_RTC>;
- clock-names = "rtc";
- interrupt-parent = <&pmu_system_controller>;
- status = "disabled";
- };
-
tmu: tmu at 10060000 {
compatible = "samsung,exynos5250-tmu";
reg = <0x10060000 0x100>;
@@ -276,26 +269,6 @@
};
};
- serial at 12C00000 {
- clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- serial at 12C10000 {
- clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- serial at 12C20000 {
- clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- serial at 12C30000 {
- clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
sata: sata at 122F0000 {
compatible = "snps,dwc-ahci";
samsung,sata-freq = <66>;
@@ -778,20 +751,6 @@
#phy-cells = <0>;
};
- dp: dp-controller at 145B0000 {
- power-domains = <&pd_disp1>;
- clocks = <&clock CLK_DP>;
- clock-names = "dp";
- phys = <&dp_phy>;
- phy-names = "dp";
- };
-
- fimd: fimd at 14400000 {
- power-domains = <&pd_disp1>;
- clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
- clock-names = "sclk_fimd", "fimd";
- };
-
adc: adc at 12D10000 {
compatible = "samsung,exynos-adc-v1";
reg = <0x12D10000 0x100>;
@@ -812,3 +771,44 @@
clock-names = "secss";
};
};
+
+&dp {
+ power-domains = <&pd_disp1>;
+ clocks = <&clock CLK_DP>;
+ clock-names = "dp";
+ phys = <&dp_phy>;
+ phy-names = "dp";
+};
+
+&fimd {
+ power-domains = <&pd_disp1>;
+ clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
+ clock-names = "sclk_fimd", "fimd";
+};
+
+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
+&serial_0 {
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+ clock-names = "uart", "clk_uart_baud0";
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 3/7] ARM: dts: Remove duplicated I2C 7 nodes in Snow
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5250-snow.dts | 46 +++++++++++++++++------------------
1 file changed, 22 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index 2657e842e5a5..7ecdad0517e7 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -177,30 +177,6 @@
};
};
- i2c@12CD0000 {
- ptn3460: lvds-bridge@20 {
- compatible = "nxp,ptn3460";
- reg = <0x20>;
- powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
- edid-emulation = <5>;
-
- ports {
- port@0 {
- bridge_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
-
- port@1 {
- bridge_in: endpoint {
- remote-endpoint = <&dp_out>;
- };
- };
- };
- };
- };
-
sound {
compatible = "google,snow-audio-max98095";
@@ -507,6 +483,28 @@
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
+ ptn3460: lvds-bridge@20 {
+ compatible = "nxp,ptn3460";
+ reg = <0x20>;
+ powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
+ edid-emulation = <5>;
+
+ ports {
+ port@0 {
+ bridge_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+
+ port@1 {
+ bridge_in: endpoint {
+ remote-endpoint = <&dp_out>;
+ };
+ };
+ };
+ };
+
max98095: codec@11 {
compatible = "maxim,max98095";
reg = <0x11>;
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 3/7] ARM: dts: Remove duplicated I2C 7 nodes in Snow
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
The i2c_7 node (i2c at 12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5250-snow.dts | 46 +++++++++++++++++------------------
1 file changed, 22 insertions(+), 24 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index 2657e842e5a5..7ecdad0517e7 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -177,30 +177,6 @@
};
};
- i2c at 12CD0000 {
- ptn3460: lvds-bridge at 20 {
- compatible = "nxp,ptn3460";
- reg = <0x20>;
- powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
- edid-emulation = <5>;
-
- ports {
- port at 0 {
- bridge_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
-
- port at 1 {
- bridge_in: endpoint {
- remote-endpoint = <&dp_out>;
- };
- };
- };
- };
- };
-
sound {
compatible = "google,snow-audio-max98095";
@@ -507,6 +483,28 @@
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
+ ptn3460: lvds-bridge at 20 {
+ compatible = "nxp,ptn3460";
+ reg = <0x20>;
+ powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
+ edid-emulation = <5>;
+
+ ports {
+ port at 0 {
+ bridge_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+
+ port at 1 {
+ bridge_in: endpoint {
+ remote-endpoint = <&dp_out>;
+ };
+ };
+ };
+ };
+
max98095: codec at 11 {
compatible = "maxim,max98095";
reg = <0x11>;
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 4/7] ARM: dts: Use phandle notation for overriding nodes in Arndale Octa
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5420-arndale-octa.dts | 634 +++++++++++++-------------
1 file changed, 317 insertions(+), 317 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index 97346df31d41..7eb0e6b703bf 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -39,323 +39,6 @@
};
};
- codec@11000000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- };
-
- mmc@12200000 {
- status = "okay";
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
- vmmc-supply = <&ldo10_reg>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- mmc@12220000 {
- status = "okay";
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
- vmmc-supply = <&ldo19_reg>;
- vqmmc-supply = <&ldo13_reg>;
- bus-width = <4>;
- cap-sd-highspeed;
- };
-
- hsi2c_4: i2c@12CA0000 {
- status = "okay";
-
- s2mps11_pmic@66 {
- compatible = "samsung,s2mps11-pmic";
- reg = <0x66>;
- s2mps11,buck2-ramp-delay = <12>;
- s2mps11,buck34-ramp-delay = <12>;
- s2mps11,buck16-ramp-delay = <12>;
- s2mps11,buck6-ramp-enable = <1>;
- s2mps11,buck2-ramp-enable = <1>;
- s2mps11,buck3-ramp-enable = <1>;
- s2mps11,buck4-ramp-enable = <1>;
-
- interrupt-parent = <&gpx3>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&s2mps11_irq>;
-
- s2mps11_osc: clocks {
- #clock-cells = <1>;
- clock-output-names = "s2mps11_ap",
- "s2mps11_cp", "s2mps11_bt";
- };
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "PVDD_ALIVE_1V0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "PVDD_APIO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "PVDD_APIO_MMCON_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "PVDD_ADC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "PVDD_PLL_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "PVDD_ANAIP_1V0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "PVDD_ANAIP_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "PVDD_ABB_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "PVDD_USB_3V3";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "PVDD_PRE_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "PVDD_USB_1V0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "PVDD_HSIC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "PVDD_APIO_MMCOFF_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "PVDD_PERI_2V8";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "PVDD_PERI_3V3";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- };
-
- ldo18_reg: LDO18 {
- regulator-name = "PVDD_EMMC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "PVDD_TFLASH_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "PVDD_BTWIFI_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "PVDD_CAM1IO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo23_reg: LDO23 {
- regulator-name = "PVDD_MIFS_1V1";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "PVDD_CAM1_AVDD_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo26_reg: LDO26 {
- regulator-name = "PVDD_CAM0_AF_2V8";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo27_reg: LDO27 {
- regulator-name = "PVDD_G3DS_1V0";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo28_reg: LDO28 {
- regulator-name = "PVDD_TSP_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo29_reg: LDO29 {
- regulator-name = "PVDD_AUDIO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo31_reg: LDO31 {
- regulator-name = "PVDD_PERI_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo32_reg: LDO32 {
- regulator-name = "PVDD_LCD_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo33_reg: LDO33 {
- regulator-name = "PVDD_CAM0IO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo35_reg: LDO35 {
- regulator-name = "PVDD_CAM0_DVDD_1V2";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo38_reg: LDO38 {
- regulator-name = "PVDD_CAM0_AVDD_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "PVDD_MIF_1V1";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "PVDD_INT_1V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "PVDD_G3D_1V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "PVDD_LPDDR3_1V2";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "PVDD_KFC_1V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VIN_LLDO_1V4";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "VIN_MLDO_2V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "VIN_HLDO_3V5";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3500000>;
- regulator-always-on;
- };
-
- buck10_reg: BUCK10 {
- regulator-name = "PVDD_EMMCF_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
@@ -376,6 +59,323 @@
status = "disabled";
};
+&hsi2c_4 {
+ status = "okay";
+
+ s2mps11_pmic@66 {
+ compatible = "samsung,s2mps11-pmic";
+ reg = <0x66>;
+ s2mps11,buck2-ramp-delay = <12>;
+ s2mps11,buck34-ramp-delay = <12>;
+ s2mps11,buck16-ramp-delay = <12>;
+ s2mps11,buck6-ramp-enable = <1>;
+ s2mps11,buck2-ramp-enable = <1>;
+ s2mps11,buck3-ramp-enable = <1>;
+ s2mps11,buck4-ramp-enable = <1>;
+
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s2mps11_irq>;
+
+ s2mps11_osc: clocks {
+ #clock-cells = <1>;
+ clock-output-names = "s2mps11_ap",
+ "s2mps11_cp", "s2mps11_bt";
+ };
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "PVDD_ALIVE_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "PVDD_APIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "PVDD_APIO_MMCON_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "PVDD_ADC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "PVDD_PLL_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "PVDD_ANAIP_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "PVDD_ANAIP_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "PVDD_ABB_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "PVDD_USB_3V3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "PVDD_PRE_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "PVDD_USB_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "PVDD_HSIC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "PVDD_APIO_MMCOFF_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "PVDD_PERI_2V8";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "PVDD_PERI_3V3";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "PVDD_EMMC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "PVDD_TFLASH_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "PVDD_BTWIFI_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "PVDD_CAM1IO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "PVDD_MIFS_1V1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "PVDD_CAM1_AVDD_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "PVDD_CAM0_AF_2V8";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "PVDD_G3DS_1V0";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "PVDD_TSP_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo29_reg: LDO29 {
+ regulator-name = "PVDD_AUDIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo31_reg: LDO31 {
+ regulator-name = "PVDD_PERI_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo32_reg: LDO32 {
+ regulator-name = "PVDD_LCD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo33_reg: LDO33 {
+ regulator-name = "PVDD_CAM0IO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo35_reg: LDO35 {
+ regulator-name = "PVDD_CAM0_DVDD_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo38_reg: LDO38 {
+ regulator-name = "PVDD_CAM0_AVDD_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "PVDD_MIF_1V1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "PVDD_INT_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "PVDD_G3D_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "PVDD_LPDDR3_1V2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "PVDD_KFC_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VIN_LLDO_1V4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "VIN_MLDO_2V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "VIN_HLDO_3V5";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "PVDD_EMMCF_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ };
+ };
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&mmc_0 {
+ status = "okay";
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ vmmc-supply = <&ldo10_reg>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
+&mmc_2 {
+ status = "okay";
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+ vmmc-supply = <&ldo19_reg>;
+ vqmmc-supply = <&ldo13_reg>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+};
+
&rtc {
status = "okay";
clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 4/7] ARM: dts: Use phandle notation for overriding nodes in Arndale Octa
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5420-arndale-octa.dts | 634 +++++++++++++-------------
1 file changed, 317 insertions(+), 317 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index 97346df31d41..7eb0e6b703bf 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -39,323 +39,6 @@
};
};
- codec at 11000000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- };
-
- mmc at 12200000 {
- status = "okay";
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
- vmmc-supply = <&ldo10_reg>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- mmc at 12220000 {
- status = "okay";
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
- vmmc-supply = <&ldo19_reg>;
- vqmmc-supply = <&ldo13_reg>;
- bus-width = <4>;
- cap-sd-highspeed;
- };
-
- hsi2c_4: i2c at 12CA0000 {
- status = "okay";
-
- s2mps11_pmic at 66 {
- compatible = "samsung,s2mps11-pmic";
- reg = <0x66>;
- s2mps11,buck2-ramp-delay = <12>;
- s2mps11,buck34-ramp-delay = <12>;
- s2mps11,buck16-ramp-delay = <12>;
- s2mps11,buck6-ramp-enable = <1>;
- s2mps11,buck2-ramp-enable = <1>;
- s2mps11,buck3-ramp-enable = <1>;
- s2mps11,buck4-ramp-enable = <1>;
-
- interrupt-parent = <&gpx3>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&s2mps11_irq>;
-
- s2mps11_osc: clocks {
- #clock-cells = <1>;
- clock-output-names = "s2mps11_ap",
- "s2mps11_cp", "s2mps11_bt";
- };
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "PVDD_ALIVE_1V0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "PVDD_APIO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "PVDD_APIO_MMCON_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "PVDD_ADC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "PVDD_PLL_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "PVDD_ANAIP_1V0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "PVDD_ANAIP_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "PVDD_ABB_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "PVDD_USB_3V3";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "PVDD_PRE_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "PVDD_USB_1V0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "PVDD_HSIC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "PVDD_APIO_MMCOFF_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "PVDD_PERI_2V8";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "PVDD_PERI_3V3";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- };
-
- ldo18_reg: LDO18 {
- regulator-name = "PVDD_EMMC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "PVDD_TFLASH_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "PVDD_BTWIFI_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "PVDD_CAM1IO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo23_reg: LDO23 {
- regulator-name = "PVDD_MIFS_1V1";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "PVDD_CAM1_AVDD_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo26_reg: LDO26 {
- regulator-name = "PVDD_CAM0_AF_2V8";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo27_reg: LDO27 {
- regulator-name = "PVDD_G3DS_1V0";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo28_reg: LDO28 {
- regulator-name = "PVDD_TSP_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo29_reg: LDO29 {
- regulator-name = "PVDD_AUDIO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo31_reg: LDO31 {
- regulator-name = "PVDD_PERI_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo32_reg: LDO32 {
- regulator-name = "PVDD_LCD_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo33_reg: LDO33 {
- regulator-name = "PVDD_CAM0IO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo35_reg: LDO35 {
- regulator-name = "PVDD_CAM0_DVDD_1V2";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo38_reg: LDO38 {
- regulator-name = "PVDD_CAM0_AVDD_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "PVDD_MIF_1V1";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "PVDD_INT_1V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "PVDD_G3D_1V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "PVDD_LPDDR3_1V2";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "PVDD_KFC_1V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VIN_LLDO_1V4";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "VIN_MLDO_2V0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "VIN_HLDO_3V5";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3500000>;
- regulator-always-on;
- };
-
- buck10_reg: BUCK10 {
- regulator-name = "PVDD_EMMCF_2V8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
@@ -376,6 +59,323 @@
status = "disabled";
};
+&hsi2c_4 {
+ status = "okay";
+
+ s2mps11_pmic at 66 {
+ compatible = "samsung,s2mps11-pmic";
+ reg = <0x66>;
+ s2mps11,buck2-ramp-delay = <12>;
+ s2mps11,buck34-ramp-delay = <12>;
+ s2mps11,buck16-ramp-delay = <12>;
+ s2mps11,buck6-ramp-enable = <1>;
+ s2mps11,buck2-ramp-enable = <1>;
+ s2mps11,buck3-ramp-enable = <1>;
+ s2mps11,buck4-ramp-enable = <1>;
+
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s2mps11_irq>;
+
+ s2mps11_osc: clocks {
+ #clock-cells = <1>;
+ clock-output-names = "s2mps11_ap",
+ "s2mps11_cp", "s2mps11_bt";
+ };
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "PVDD_ALIVE_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "PVDD_APIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "PVDD_APIO_MMCON_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "PVDD_ADC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "PVDD_PLL_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "PVDD_ANAIP_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "PVDD_ANAIP_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "PVDD_ABB_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "PVDD_USB_3V3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "PVDD_PRE_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "PVDD_USB_1V0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "PVDD_HSIC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "PVDD_APIO_MMCOFF_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "PVDD_PERI_2V8";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "PVDD_PERI_3V3";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "PVDD_EMMC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "PVDD_TFLASH_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "PVDD_BTWIFI_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "PVDD_CAM1IO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "PVDD_MIFS_1V1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "PVDD_CAM1_AVDD_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "PVDD_CAM0_AF_2V8";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "PVDD_G3DS_1V0";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "PVDD_TSP_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo29_reg: LDO29 {
+ regulator-name = "PVDD_AUDIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo31_reg: LDO31 {
+ regulator-name = "PVDD_PERI_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo32_reg: LDO32 {
+ regulator-name = "PVDD_LCD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo33_reg: LDO33 {
+ regulator-name = "PVDD_CAM0IO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo35_reg: LDO35 {
+ regulator-name = "PVDD_CAM0_DVDD_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo38_reg: LDO38 {
+ regulator-name = "PVDD_CAM0_AVDD_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "PVDD_MIF_1V1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "PVDD_INT_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "PVDD_G3D_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "PVDD_LPDDR3_1V2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "PVDD_KFC_1V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VIN_LLDO_1V4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "VIN_MLDO_2V0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "VIN_HLDO_3V5";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "PVDD_EMMCF_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ };
+ };
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&mmc_0 {
+ status = "okay";
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ vmmc-supply = <&ldo10_reg>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
+&mmc_2 {
+ status = "okay";
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+ vmmc-supply = <&ldo19_reg>;
+ vqmmc-supply = <&ldo13_reg>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+};
+
&rtc {
status = "okay";
clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 5/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5420
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
The phandle notation reduces possible mistakes when overriding nodes.
Additionally remove duplicated serial and uart labels for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5420-peach-pit.dts | 2 +-
arch/arm/boot/dts/exynos5420.dtsi | 80 +++++++++++++++---------------
arch/arm/boot/dts/exynos5800-peach-pi.dts | 2 +-
3 files changed, 42 insertions(+), 42 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 3f4e2feaa927..9d199ce01314 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -1024,7 +1024,7 @@
};
};
-&uart_3 {
+&serial_3 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index c7a44ee0ce06..25228527294c 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -328,13 +328,6 @@
interrupts = <0 47 0>;
};
- rtc: rtc@101E0000 {
- clocks = <&clock CLK_RTC>;
- clock-names = "rtc";
- interrupt-parent = <&pmu_system_controller>;
- status = "disabled";
- };
-
amba {
#address-cells = <1>;
#size-cells = <1>;
@@ -496,26 +489,6 @@
status = "disabled";
};
- uart_0: serial@12C00000 {
- clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- uart_1: serial@12C10000 {
- clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- uart_2: serial@12C20000 {
- clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- uart_3: serial@12C30000 {
- clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
pwm: pwm@12dd0000 {
compatible = "samsung,exynos4210-pwm";
reg = <0x12dd0000 0x100>;
@@ -531,13 +504,6 @@
#phy-cells = <0>;
};
- dp: dp-controller@145B0000 {
- clocks = <&clock CLK_DP1>;
- clock-names = "dp";
- phys = <&dp_phy>;
- phy-names = "dp";
- };
-
mipi_phy: video-phy@10040714 {
compatible = "samsung,s5pv210-mipi-video-phy";
reg = <0x10040714 12>;
@@ -557,12 +523,6 @@
status = "disabled";
};
- fimd: fimd@14400000 {
- clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
- clock-names = "sclk_fimd", "fimd";
- power-domains = <&disp_pd>;
- };
-
adc: adc@12D10000 {
compatible = "samsung,exynos-adc-v2";
reg = <0x12D10000 0x100>;
@@ -962,3 +922,43 @@
samsung,pmureg-phandle = <&pmu_system_controller>;
};
};
+
+&dp {
+ clocks = <&clock CLK_DP1>;
+ clock-names = "dp";
+ phys = <&dp_phy>;
+ phy-names = "dp";
+};
+
+&fimd {
+ clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
+ clock-names = "sclk_fimd", "fimd";
+ power-domains = <&disp_pd>;
+};
+
+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
+&serial_0 {
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+ clock-names = "uart", "clk_uart_baud0";
+};
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index c833bacf873b..9d26abd88dfd 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -986,7 +986,7 @@
};
};
-&uart_3 {
+&serial_3 {
status = "okay";
};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 5/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5420
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
The phandle notation reduces possible mistakes when overriding nodes.
Additionally remove duplicated serial and uart labels for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5420-peach-pit.dts | 2 +-
arch/arm/boot/dts/exynos5420.dtsi | 80 +++++++++++++++---------------
arch/arm/boot/dts/exynos5800-peach-pi.dts | 2 +-
3 files changed, 42 insertions(+), 42 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 3f4e2feaa927..9d199ce01314 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -1024,7 +1024,7 @@
};
};
-&uart_3 {
+&serial_3 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index c7a44ee0ce06..25228527294c 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -328,13 +328,6 @@
interrupts = <0 47 0>;
};
- rtc: rtc at 101E0000 {
- clocks = <&clock CLK_RTC>;
- clock-names = "rtc";
- interrupt-parent = <&pmu_system_controller>;
- status = "disabled";
- };
-
amba {
#address-cells = <1>;
#size-cells = <1>;
@@ -496,26 +489,6 @@
status = "disabled";
};
- uart_0: serial at 12C00000 {
- clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- uart_1: serial at 12C10000 {
- clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- uart_2: serial at 12C20000 {
- clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
- uart_3: serial at 12C30000 {
- clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
- clock-names = "uart", "clk_uart_baud0";
- };
-
pwm: pwm at 12dd0000 {
compatible = "samsung,exynos4210-pwm";
reg = <0x12dd0000 0x100>;
@@ -531,13 +504,6 @@
#phy-cells = <0>;
};
- dp: dp-controller at 145B0000 {
- clocks = <&clock CLK_DP1>;
- clock-names = "dp";
- phys = <&dp_phy>;
- phy-names = "dp";
- };
-
mipi_phy: video-phy at 10040714 {
compatible = "samsung,s5pv210-mipi-video-phy";
reg = <0x10040714 12>;
@@ -557,12 +523,6 @@
status = "disabled";
};
- fimd: fimd at 14400000 {
- clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
- clock-names = "sclk_fimd", "fimd";
- power-domains = <&disp_pd>;
- };
-
adc: adc at 12D10000 {
compatible = "samsung,exynos-adc-v2";
reg = <0x12D10000 0x100>;
@@ -962,3 +922,43 @@
samsung,pmureg-phandle = <&pmu_system_controller>;
};
};
+
+&dp {
+ clocks = <&clock CLK_DP1>;
+ clock-names = "dp";
+ phys = <&dp_phy>;
+ phy-names = "dp";
+};
+
+&fimd {
+ clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
+ clock-names = "sclk_fimd", "fimd";
+ power-domains = <&disp_pd>;
+};
+
+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
+&serial_0 {
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_1 {
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_2 {
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+};
+
+&serial_3 {
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
+ clock-names = "uart", "clk_uart_baud0";
+};
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index c833bacf873b..9d26abd88dfd 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -986,7 +986,7 @@
};
};
-&uart_3 {
+&serial_3 {
status = "okay";
};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 6/7] ARM: dts: Use phandle notation for overriding nodes in SMDK5420
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5420-smdk5420.dts | 639 +++++++++++++++---------------
1 file changed, 320 insertions(+), 319 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index 7a56852efada..0a5d812b5c85 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -64,102 +64,6 @@
};
};
- rtc@101E0000 {
- status = "okay";
- };
-
- codec@11000000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- };
-
- mmc@12200000 {
- status = "okay";
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- mmc@12220000 {
- status = "okay";
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
- bus-width = <4>;
- cap-sd-highspeed;
- };
-
- dp-controller@145B0000 {
- pinctrl-names = "default";
- pinctrl-0 = <&dp_hpd>;
- samsung,color-space = <0>;
- samsung,dynamic-range = <0>;
- samsung,ycbcr-coeff = <0>;
- samsung,color-depth = <1>;
- samsung,link-rate = <0x0a>;
- samsung,lane-count = <4>;
- status = "okay";
- };
-
- fimd@14400000 {
- status = "okay";
- display-timings {
- native-mode = <&timing0>;
- timing0: timing@0 {
- clock-frequency = <50000>;
- hactive = <2560>;
- vactive = <1600>;
- hfront-porch = <48>;
- hback-porch = <80>;
- hsync-len = <32>;
- vback-porch = <16>;
- vfront-porch = <8>;
- vsync-len = <6>;
- };
- };
- };
-
- pinctrl@13400000 {
- hdmi_hpd_irq: hdmi-hpd-irq {
- samsung,pins = "gpx3-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
- };
- };
-
- pinctrl@14000000 {
- usb300_vbus_en: usb300-vbus-en {
- samsung,pins = "gpg0-5";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- usb301_vbus_en: usb301-vbus-en {
- samsung,pins = "gpg1-4";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
- };
-
- hdmi@14530000 {
- status = "okay";
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd_irq>;
- };
-
usb300_vbus_reg: regulator-usb300 {
compatible = "regulator-fixed";
regulator-name = "VBUS0";
@@ -182,238 +86,335 @@
enable-active-high;
};
- phy@12100000 {
- vbus-supply = <&usb300_vbus_reg>;
- };
+};
- phy@12500000 {
- vbus-supply = <&usb301_vbus_reg>;
+&dp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hpd>;
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <4>;
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing@0 {
+ clock-frequency = <50000>;
+ hactive = <2560>;
+ vactive = <1600>;
+ hfront-porch = <48>;
+ hback-porch = <80>;
+ hsync-len = <32>;
+ vback-porch = <16>;
+ vfront-porch = <8>;
+ vsync-len = <6>;
+ };
};
+};
- i2c_2: i2c@12C80000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- status = "okay";
+&hdmi {
+ status = "okay";
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+};
- hdmiddc@50 {
- compatible = "samsung,exynos4210-hdmiddc";
- reg = <0x50>;
+&hsi2c_4 {
+ status = "okay";
+
+ s2mps11_pmic@66 {
+ compatible = "samsung,s2mps11-pmic";
+ reg = <0x66>;
+ s2mps11,buck2-ramp-delay = <12>;
+ s2mps11,buck34-ramp-delay = <12>;
+ s2mps11,buck16-ramp-delay = <12>;
+ s2mps11,buck6-ramp-enable = <1>;
+ s2mps11,buck2-ramp-enable = <1>;
+ s2mps11,buck3-ramp-enable = <1>;
+ s2mps11,buck4-ramp-enable = <1>;
+
+ s2mps11_osc: clocks {
+ #clock-cells = <1>;
+ clock-output-names = "s2mps11_ap",
+ "s2mps11_cp", "s2mps11_bt";
};
- };
- hsi2c_4: i2c@12CA0000 {
- status = "okay";
-
- s2mps11_pmic@66 {
- compatible = "samsung,s2mps11-pmic";
- reg = <0x66>;
- s2mps11,buck2-ramp-delay = <12>;
- s2mps11,buck34-ramp-delay = <12>;
- s2mps11,buck16-ramp-delay = <12>;
- s2mps11,buck6-ramp-enable = <1>;
- s2mps11,buck2-ramp-enable = <1>;
- s2mps11,buck3-ramp-enable = <1>;
- s2mps11,buck4-ramp-enable = <1>;
-
- s2mps11_osc: clocks {
- #clock-cells = <1>;
- clock-output-names = "s2mps11_ap",
- "s2mps11_cp", "s2mps11_bt";
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "vdd_ldo1";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "vdd_ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "vdd_ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "vdd_ldo6";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "vdd_ldo7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "vdd_ldo8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "vdd_ldo9";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "vdd_ldo10";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "vdd_ldo11";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "vdd_ldo12";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
};
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "vdd_ldo1";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "vdd_ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "vdd_ldo5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "vdd_ldo6";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "vdd_ldo7";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "vdd_ldo8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "vdd_ldo9";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "vdd_ldo10";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "vdd_ldo11";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "vdd_ldo12";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "vdd_ldo13";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "vdd_ldo15";
- regulator-min-microvolt = <3100000>;
- regulator-max-microvolt = <3100000>;
- regulator-always-on;
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "vdd_ldo16";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- regulator-always-on;
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "tsp_avdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "tsp_io";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "vdd_mem";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "vdd_kfc";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "vdd_1.0v_ldo";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "vdd_1.8v_ldo";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "vdd_2.8v_ldo";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3750000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck10_reg: BUCK10 {
- regulator-name = "vdd_vmem";
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo13_reg: LDO13 {
+ regulator-name = "vdd_ldo13";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "vdd_ldo15";
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-always-on;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "vdd_ldo16";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ regulator-always-on;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "tsp_avdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "tsp_io";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "vdd_mem";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "vdd_kfc";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "vdd_1.0v_ldo";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "vdd_1.8v_ldo";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "vdd_2.8v_ldo";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3750000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "vdd_vmem";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ regulator-always-on;
+ regulator-boot-on;
};
};
};
};
+
+&i2c_2 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+ status = "okay";
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&mmc_0 {
+ status = "okay";
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
+&mmc_2 {
+ status = "okay";
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+};
+
+&pinctrl_0 {
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_2 {
+ usb300_vbus_en: usb300-vbus-en {
+ samsung,pins = "gpg0-5";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ usb301_vbus_en: usb301-vbus-en {
+ samsung,pins = "gpg1-4";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&usbdrd_phy0 {
+ vbus-supply = <&usb300_vbus_reg>;
+};
+
+&usbdrd_phy1 {
+ vbus-supply = <&usb301_vbus_reg>;
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 6/7] ARM: dts: Use phandle notation for overriding nodes in SMDK5420
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5420-smdk5420.dts | 639 +++++++++++++++---------------
1 file changed, 320 insertions(+), 319 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index 7a56852efada..0a5d812b5c85 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -64,102 +64,6 @@
};
};
- rtc at 101E0000 {
- status = "okay";
- };
-
- codec at 11000000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- };
-
- mmc at 12200000 {
- status = "okay";
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <0 4>;
- samsung,dw-mshc-ddr-timing = <0 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- mmc at 12220000 {
- status = "okay";
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
- bus-width = <4>;
- cap-sd-highspeed;
- };
-
- dp-controller at 145B0000 {
- pinctrl-names = "default";
- pinctrl-0 = <&dp_hpd>;
- samsung,color-space = <0>;
- samsung,dynamic-range = <0>;
- samsung,ycbcr-coeff = <0>;
- samsung,color-depth = <1>;
- samsung,link-rate = <0x0a>;
- samsung,lane-count = <4>;
- status = "okay";
- };
-
- fimd at 14400000 {
- status = "okay";
- display-timings {
- native-mode = <&timing0>;
- timing0: timing at 0 {
- clock-frequency = <50000>;
- hactive = <2560>;
- vactive = <1600>;
- hfront-porch = <48>;
- hback-porch = <80>;
- hsync-len = <32>;
- vback-porch = <16>;
- vfront-porch = <8>;
- vsync-len = <6>;
- };
- };
- };
-
- pinctrl at 13400000 {
- hdmi_hpd_irq: hdmi-hpd-irq {
- samsung,pins = "gpx3-7";
- samsung,pin-function = <0>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
- };
- };
-
- pinctrl at 14000000 {
- usb300_vbus_en: usb300-vbus-en {
- samsung,pins = "gpg0-5";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
-
- usb301_vbus_en: usb301-vbus-en {
- samsung,pins = "gpg1-4";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
- };
-
- hdmi at 14530000 {
- status = "okay";
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd_irq>;
- };
-
usb300_vbus_reg: regulator-usb300 {
compatible = "regulator-fixed";
regulator-name = "VBUS0";
@@ -182,238 +86,335 @@
enable-active-high;
};
- phy at 12100000 {
- vbus-supply = <&usb300_vbus_reg>;
- };
+};
- phy at 12500000 {
- vbus-supply = <&usb301_vbus_reg>;
+&dp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hpd>;
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <4>;
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing at 0 {
+ clock-frequency = <50000>;
+ hactive = <2560>;
+ vactive = <1600>;
+ hfront-porch = <48>;
+ hback-porch = <80>;
+ hsync-len = <32>;
+ vback-porch = <16>;
+ vfront-porch = <8>;
+ vsync-len = <6>;
+ };
};
+};
- i2c_2: i2c at 12C80000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <66000>;
- status = "okay";
+&hdmi {
+ status = "okay";
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+};
- hdmiddc at 50 {
- compatible = "samsung,exynos4210-hdmiddc";
- reg = <0x50>;
+&hsi2c_4 {
+ status = "okay";
+
+ s2mps11_pmic at 66 {
+ compatible = "samsung,s2mps11-pmic";
+ reg = <0x66>;
+ s2mps11,buck2-ramp-delay = <12>;
+ s2mps11,buck34-ramp-delay = <12>;
+ s2mps11,buck16-ramp-delay = <12>;
+ s2mps11,buck6-ramp-enable = <1>;
+ s2mps11,buck2-ramp-enable = <1>;
+ s2mps11,buck3-ramp-enable = <1>;
+ s2mps11,buck4-ramp-enable = <1>;
+
+ s2mps11_osc: clocks {
+ #clock-cells = <1>;
+ clock-output-names = "s2mps11_ap",
+ "s2mps11_cp", "s2mps11_bt";
};
- };
- hsi2c_4: i2c at 12CA0000 {
- status = "okay";
-
- s2mps11_pmic at 66 {
- compatible = "samsung,s2mps11-pmic";
- reg = <0x66>;
- s2mps11,buck2-ramp-delay = <12>;
- s2mps11,buck34-ramp-delay = <12>;
- s2mps11,buck16-ramp-delay = <12>;
- s2mps11,buck6-ramp-enable = <1>;
- s2mps11,buck2-ramp-enable = <1>;
- s2mps11,buck3-ramp-enable = <1>;
- s2mps11,buck4-ramp-enable = <1>;
-
- s2mps11_osc: clocks {
- #clock-cells = <1>;
- clock-output-names = "s2mps11_ap",
- "s2mps11_cp", "s2mps11_bt";
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "vdd_ldo1";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "vdd_ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "vdd_ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "vdd_ldo6";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "vdd_ldo7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "vdd_ldo8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "vdd_ldo9";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "vdd_ldo10";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "vdd_ldo11";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "vdd_ldo12";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
};
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "vdd_ldo1";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "vdd_ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "vdd_ldo5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "vdd_ldo6";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "vdd_ldo7";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "vdd_ldo8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "vdd_ldo9";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "vdd_ldo10";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "vdd_ldo11";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "vdd_ldo12";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "vdd_ldo13";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "vdd_ldo15";
- regulator-min-microvolt = <3100000>;
- regulator-max-microvolt = <3100000>;
- regulator-always-on;
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "vdd_ldo16";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- regulator-always-on;
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "tsp_avdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "tsp_io";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "vdd_mem";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "vdd_kfc";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "vdd_1.0v_ldo";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "vdd_1.8v_ldo";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "vdd_2.8v_ldo";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3750000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck10_reg: BUCK10 {
- regulator-name = "vdd_vmem";
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo13_reg: LDO13 {
+ regulator-name = "vdd_ldo13";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "vdd_ldo15";
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-always-on;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "vdd_ldo16";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ regulator-always-on;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "tsp_avdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "tsp_io";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "vdd_mem";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "vdd_kfc";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "vdd_1.0v_ldo";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "vdd_1.8v_ldo";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "vdd_2.8v_ldo";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3750000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck10_reg: BUCK10 {
+ regulator-name = "vdd_vmem";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ regulator-always-on;
+ regulator-boot-on;
};
};
};
};
+
+&i2c_2 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+ status = "okay";
+
+ hdmiddc at 50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&mmc_0 {
+ status = "okay";
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <0 4>;
+ samsung,dw-mshc-ddr-timing = <0 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
+&mmc_2 {
+ status = "okay";
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+};
+
+&pinctrl_0 {
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_2 {
+ usb300_vbus_en: usb300-vbus-en {
+ samsung,pins = "gpg0-5";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ usb301_vbus_en: usb301-vbus-en {
+ samsung,pins = "gpg1-4";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&usbdrd_phy0 {
+ vbus-supply = <&usb300_vbus_reg>;
+};
+
+&usbdrd_phy1 {
+ vbus-supply = <&usb301_vbus_reg>;
+};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 7/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5440 boards
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Arnd Bergmann, Olof Johansson, Marek Szyprowski, Krzysztof Kozlowski
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5440-sd5v1.dts | 10 ++--
arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 +++++++++++++++----------------
2 files changed, 47 insertions(+), 48 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5440-sd5v1.dts b/arch/arm/boot/dts/exynos5440-sd5v1.dts
index 268609a42b2c..a98501bab6fc 100644
--- a/arch/arm/boot/dts/exynos5440-sd5v1.dts
+++ b/arch/arm/boot/dts/exynos5440-sd5v1.dts
@@ -27,13 +27,13 @@
};
};
- gmac: ethernet@00230000 {
- fixed_phy;
- phy_addr = <1>;
- };
-
spi {
status = "disabled";
};
};
+
+&gmac {
+ fixed_phy;
+ phy_addr = <1>;
+};
diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
index ff55dac6e219..e4443f4e6572 100644
--- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts
+++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
@@ -20,59 +20,58 @@
bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200";
};
- spi_0: spi@D0000 {
-
- flash: w25q128@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "winbond,w25q128";
- spi-max-frequency = <15625000>;
- reg = <0>;
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
+ fixed-rate-clocks {
+ xtal {
+ compatible = "samsung,clock-xtal";
+ clock-frequency = <50000000>;
+ };
+ };
+};
- partition@00000 {
- label = "BootLoader";
- reg = <0x60000 0x80000>;
- read-only;
- };
+&pcie_0 {
+ reset-gpio = <&pin_ctrl 5 0>;
+ status = "okay";
+};
- partition@e0000 {
- label = "Recovery-Kernel";
- reg = <0xe0000 0x300000>;
- read-only;
- };
+&pcie_1 {
+ reset-gpio = <&pin_ctrl 22 0>;
+ status = "okay";
+};
- partition@3e0000 {
- label = "CRAM-FS";
- reg = <0x3e0000 0x700000>;
- read-only;
- };
+&spi_0 {
+ flash: w25q128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "winbond,w25q128";
+ spi-max-frequency = <15625000>;
+ reg = <0>;
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
+ };
- partition@ae0000 {
- label = "User-Data";
- reg = <0xae0000 0x520000>;
- };
+ partition@00000 {
+ label = "BootLoader";
+ reg = <0x60000 0x80000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "Recovery-Kernel";
+ reg = <0xe0000 0x300000>;
+ read-only;
};
- };
+ partition@3e0000 {
+ label = "CRAM-FS";
+ reg = <0x3e0000 0x700000>;
+ read-only;
+ };
- fixed-rate-clocks {
- xtal {
- compatible = "samsung,clock-xtal";
- clock-frequency = <50000000>;
+ partition@ae0000 {
+ label = "User-Data";
+ reg = <0xae0000 0x520000>;
};
- };
- pcie@290000 {
- reset-gpio = <&pin_ctrl 5 0>;
- status = "okay";
};
- pcie@2a0000 {
- reset-gpio = <&pin_ctrl 22 0>;
- status = "okay";
- };
};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 7/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5440 boards
@ 2015-04-12 12:24 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2015-04-12 12:24 UTC (permalink / raw)
To: linux-arm-kernel
The phandle notation reduces possible mistakes when overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos5440-sd5v1.dts | 10 ++--
arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 +++++++++++++++----------------
2 files changed, 47 insertions(+), 48 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5440-sd5v1.dts b/arch/arm/boot/dts/exynos5440-sd5v1.dts
index 268609a42b2c..a98501bab6fc 100644
--- a/arch/arm/boot/dts/exynos5440-sd5v1.dts
+++ b/arch/arm/boot/dts/exynos5440-sd5v1.dts
@@ -27,13 +27,13 @@
};
};
- gmac: ethernet at 00230000 {
- fixed_phy;
- phy_addr = <1>;
- };
-
spi {
status = "disabled";
};
};
+
+&gmac {
+ fixed_phy;
+ phy_addr = <1>;
+};
diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
index ff55dac6e219..e4443f4e6572 100644
--- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts
+++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
@@ -20,59 +20,58 @@
bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M at 0x80000000 mem=6144M at 0x100000000 console=ttySAC0,115200";
};
- spi_0: spi at D0000 {
-
- flash: w25q128 at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "winbond,w25q128";
- spi-max-frequency = <15625000>;
- reg = <0>;
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
+ fixed-rate-clocks {
+ xtal {
+ compatible = "samsung,clock-xtal";
+ clock-frequency = <50000000>;
+ };
+ };
+};
- partition at 00000 {
- label = "BootLoader";
- reg = <0x60000 0x80000>;
- read-only;
- };
+&pcie_0 {
+ reset-gpio = <&pin_ctrl 5 0>;
+ status = "okay";
+};
- partition at e0000 {
- label = "Recovery-Kernel";
- reg = <0xe0000 0x300000>;
- read-only;
- };
+&pcie_1 {
+ reset-gpio = <&pin_ctrl 22 0>;
+ status = "okay";
+};
- partition at 3e0000 {
- label = "CRAM-FS";
- reg = <0x3e0000 0x700000>;
- read-only;
- };
+&spi_0 {
+ flash: w25q128 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "winbond,w25q128";
+ spi-max-frequency = <15625000>;
+ reg = <0>;
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
+ };
- partition at ae0000 {
- label = "User-Data";
- reg = <0xae0000 0x520000>;
- };
+ partition at 00000 {
+ label = "BootLoader";
+ reg = <0x60000 0x80000>;
+ read-only;
+ };
+ partition at e0000 {
+ label = "Recovery-Kernel";
+ reg = <0xe0000 0x300000>;
+ read-only;
};
- };
+ partition at 3e0000 {
+ label = "CRAM-FS";
+ reg = <0x3e0000 0x700000>;
+ read-only;
+ };
- fixed-rate-clocks {
- xtal {
- compatible = "samsung,clock-xtal";
- clock-frequency = <50000000>;
+ partition at ae0000 {
+ label = "User-Data";
+ reg = <0xae0000 0x520000>;
};
- };
- pcie at 290000 {
- reset-gpio = <&pin_ctrl 5 0>;
- status = "okay";
};
- pcie at 2a0000 {
- reset-gpio = <&pin_ctrl 22 0>;
- status = "okay";
- };
};
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation
2015-04-12 12:24 ` Krzysztof Kozlowski
@ 2015-04-12 20:07 ` Arnd Bergmann
-1 siblings, 0 replies; 20+ messages in thread
From: Arnd Bergmann @ 2015-04-12 20:07 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Krzysztof Kozlowski, Kukjin Kim, devicetree, linux-samsung-soc,
linux-kernel, Olof Johansson, Marek Szyprowski
On Sunday 12 April 2015 21:24:47 Krzysztof Kozlowski wrote:
>
> The phandle notation reduces possible mistakes when overriding nodes
> by child board files and reduces duplication of addresses.
>
> The patchset refactors Exynos5 boards to use the phandle way.
>
> Tested by comparison of decompiled DTB for each commit.
The patches look fine, but the description is wrong as you are not
using 'phandles' here, you are using 'labels'.
A phandle is a reference to another device node inside of a property,
and while that is normally done using labels like
interrupt-parent = <&gic>;
you can just as well use the full path in a phandle.
Arnd
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation
@ 2015-04-12 20:07 ` Arnd Bergmann
0 siblings, 0 replies; 20+ messages in thread
From: Arnd Bergmann @ 2015-04-12 20:07 UTC (permalink / raw)
To: linux-arm-kernel
On Sunday 12 April 2015 21:24:47 Krzysztof Kozlowski wrote:
>
> The phandle notation reduces possible mistakes when overriding nodes
> by child board files and reduces duplication of addresses.
>
> The patchset refactors Exynos5 boards to use the phandle way.
>
> Tested by comparison of decompiled DTB for each commit.
The patches look fine, but the description is wrong as you are not
using 'phandles' here, you are using 'labels'.
A phandle is a reference to another device node inside of a property,
and while that is normally done using labels like
interrupt-parent = <&gic>;
you can just as well use the full path in a phandle.
Arnd
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation
2015-04-12 20:07 ` Arnd Bergmann
@ 2015-04-13 10:54 ` Krzysztof Kozłowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozłowski @ 2015-04-13 10:54 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Kukjin Kim, devicetree, linux-samsung-soc,
linux-kernel, Olof Johansson, Marek Szyprowski
2015-04-13 5:07 GMT+09:00 Arnd Bergmann <arnd@arndb.de>:
> On Sunday 12 April 2015 21:24:47 Krzysztof Kozlowski wrote:
>>
>> The phandle notation reduces possible mistakes when overriding nodes
>> by child board files and reduces duplication of addresses.
>>
>> The patchset refactors Exynos5 boards to use the phandle way.
>>
>> Tested by comparison of decompiled DTB for each commit.
>
> The patches look fine, but the description is wrong as you are not
> using 'phandles' here, you are using 'labels'.
Heh, I suspected this but some docs I found referred to "&label { ...
}" also as a phandle. Thanks for pointing this out. I'll respin.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation
@ 2015-04-13 10:54 ` Krzysztof Kozłowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozłowski @ 2015-04-13 10:54 UTC (permalink / raw)
To: linux-arm-kernel
2015-04-13 5:07 GMT+09:00 Arnd Bergmann <arnd@arndb.de>:
> On Sunday 12 April 2015 21:24:47 Krzysztof Kozlowski wrote:
>>
>> The phandle notation reduces possible mistakes when overriding nodes
>> by child board files and reduces duplication of addresses.
>>
>> The patchset refactors Exynos5 boards to use the phandle way.
>>
>> Tested by comparison of decompiled DTB for each commit.
>
> The patches look fine, but the description is wrong as you are not
> using 'phandles' here, you are using 'labels'.
Heh, I suspected this but some docs I found referred to "&label { ...
}" also as a phandle. Thanks for pointing this out. I'll respin.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2015-04-13 10:54 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-04-12 12:24 [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 1/7] ARM: dts: Add labels to nodes used in Exynos5 based DTS Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 2/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5250 Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 3/7] ARM: dts: Remove duplicated I2C 7 nodes in Snow Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 4/7] ARM: dts: Use phandle notation for overriding nodes in Arndale Octa Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 5/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5420 Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 6/7] ARM: dts: Use phandle notation for overriding nodes in SMDK5420 Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 12:24 ` [PATCH 7/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5440 boards Krzysztof Kozlowski
2015-04-12 12:24 ` Krzysztof Kozlowski
2015-04-12 20:07 ` [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation Arnd Bergmann
2015-04-12 20:07 ` Arnd Bergmann
2015-04-13 10:54 ` Krzysztof Kozłowski
2015-04-13 10:54 ` Krzysztof Kozłowski
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.