[PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

Hi everyone,

This patch series introduces basic kernel support for Allwinner's H3 SoC,
mainly basic clocks and pinctrl. It also adds interrupts, timers,
watchdog, RTC, dmaengine, MMC and UARTs, which are mostly compatible to
those in earlier SoCs like A23 and A31, and can simply be reused.

These patches are based on Maxime's sunxi/for-next branch from
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git

Patch 1 adds machine support for the H3.

Patch 2 adds support for the basic clocks. The AHB1/AHB2 split could
need some discussion.

Patch 3 adds the pin sets for the H3 main PIO. 

Patch 4 adds the H3 specific parameters to the sun6i dmaengine driver.

Patch 5 adds the DTSI for the H3.

Patch 6 adds a DT for the Orange Pi Plus SBC, which these patches
were developed and tested with.

Regards,
Jens


Jens Kuske (6):
  ARM: sunxi: Introduce Allwinner H3 support
  clk: sunxi: Add H3 clocks support
  pinctrl: sunxi: Add H3 PIO controller support
  dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant
  ARM: dts: sunxi: Add Allwinner H3 DTSI
  ARM: dts: sun8i: Add Orange Pi Plus support

 Documentation/devicetree/bindings/arm/sunxi.txt    |   1 +
 Documentation/devicetree/bindings/clock/sunxi.txt  |   7 +
 .../devicetree/bindings/dma/sun6i-dma.txt          |   5 +-
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 arch/arm/boot/dts/Makefile                         |   3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts       |  82 ++++
 arch/arm/boot/dts/sun8i-h3.dtsi                    | 468 ++++++++++++++++++
 arch/arm/mach-sunxi/Kconfig                        |   2 +-
 arch/arm/mach-sunxi/sunxi.c                        |   3 +-
 drivers/clk/sunxi/clk-sunxi.c                      |  46 +-
 drivers/dma/sun6i-dma.c                            |  12 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
 14 files changed, 1151 insertions(+), 5 deletions(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
 create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

-- 
2.3.7

[PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

Hi everyone,

This patch series introduces basic kernel support for Allwinner's H3 SoC,
mainly basic clocks and pinctrl. It also adds interrupts, timers,
watchdog, RTC, dmaengine, MMC and UARTs, which are mostly compatible to
those in earlier SoCs like A23 and A31, and can simply be reused.

These patches are based on Maxime's sunxi/for-next branch from
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git

Patch 1 adds machine support for the H3.

Patch 2 adds support for the basic clocks. The AHB1/AHB2 split could
need some discussion.

Patch 3 adds the pin sets for the H3 main PIO. 

Patch 4 adds the H3 specific parameters to the sun6i dmaengine driver.

Patch 5 adds the DTSI for the H3.

Patch 6 adds a DT for the Orange Pi Plus SBC, which these patches
were developed and tested with.

Regards,
Jens


Jens Kuske (6):
  ARM: sunxi: Introduce Allwinner H3 support
  clk: sunxi: Add H3 clocks support
  pinctrl: sunxi: Add H3 PIO controller support
  dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant
  ARM: dts: sunxi: Add Allwinner H3 DTSI
  ARM: dts: sun8i: Add Orange Pi Plus support

 Documentation/devicetree/bindings/arm/sunxi.txt    |   1 +
 Documentation/devicetree/bindings/clock/sunxi.txt  |   7 +
 .../devicetree/bindings/dma/sun6i-dma.txt          |   5 +-
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 arch/arm/boot/dts/Makefile                         |   3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts       |  82 ++++
 arch/arm/boot/dts/sun8i-h3.dtsi                    | 468 ++++++++++++++++++
 arch/arm/mach-sunxi/Kconfig                        |   2 +-
 arch/arm/mach-sunxi/sunxi.c                        |   3 +-
 drivers/clk/sunxi/clk-sunxi.c                      |  46 +-
 drivers/dma/sun6i-dma.c                            |  12 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
 14 files changed, 1151 insertions(+), 5 deletions(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
 create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

-- 
2.3.7

[PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

Hi everyone,

This patch series introduces basic kernel support for Allwinner's H3 SoC,
mainly basic clocks and pinctrl. It also adds interrupts, timers,
watchdog, RTC, dmaengine, MMC and UARTs, which are mostly compatible to
those in earlier SoCs like A23 and A31, and can simply be reused.

These patches are based on Maxime's sunxi/for-next branch from
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git

Patch 1 adds machine support for the H3.

Patch 2 adds support for the basic clocks. The AHB1/AHB2 split could
need some discussion.

Patch 3 adds the pin sets for the H3 main PIO. 

Patch 4 adds the H3 specific parameters to the sun6i dmaengine driver.

Patch 5 adds the DTSI for the H3.

Patch 6 adds a DT for the Orange Pi Plus SBC, which these patches
were developed and tested with.

Regards,
Jens


Jens Kuske (6):
  ARM: sunxi: Introduce Allwinner H3 support
  clk: sunxi: Add H3 clocks support
  pinctrl: sunxi: Add H3 PIO controller support
  dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant
  ARM: dts: sunxi: Add Allwinner H3 DTSI
  ARM: dts: sun8i: Add Orange Pi Plus support

 Documentation/devicetree/bindings/arm/sunxi.txt    |   1 +
 Documentation/devicetree/bindings/clock/sunxi.txt  |   7 +
 .../devicetree/bindings/dma/sun6i-dma.txt          |   5 +-
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 arch/arm/boot/dts/Makefile                         |   3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts       |  82 ++++
 arch/arm/boot/dts/sun8i-h3.dtsi                    | 468 ++++++++++++++++++
 arch/arm/mach-sunxi/Kconfig                        |   2 +-
 arch/arm/mach-sunxi/sunxi.c                        |   3 +-
 drivers/clk/sunxi/clk-sunxi.c                      |  46 +-
 drivers/dma/sun6i-dma.c                            |  12 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
 14 files changed, 1151 insertions(+), 5 deletions(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
 create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

-- 
2.3.7

[PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
to other sun8i family SoCs like the A23.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
 arch/arm/mach-sunxi/Kconfig                     | 2 +-
 arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
 3 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index 42941fd..3cb4b94 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -9,4 +9,5 @@ using one of the following compatible strings:
   allwinner,sun6i-a31
   allwinner,sun7i-a20
   allwinner,sun8i-a23
+  allwinner,sun8i-h3
   allwinner,sun9i-a80
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 81502b9..47ac5b4 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -35,7 +35,7 @@ config MACH_SUN7I
 	select SUN5I_HSTIMER
 
 config MACH_SUN8I
-	bool "Allwinner A23 (sun8i) SoCs support"
+	bool "Allwinner A23 / H3 (sun8i) SoCs support"
 	default ARCH_SUNXI
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index 1bc811a..bc63748 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -67,10 +67,11 @@ MACHINE_END
 
 static const char * const sun8i_board_dt_compat[] = {
 	"allwinner,sun8i-a23",
+	"allwinner,sun8i-h3",
 	NULL,
 };
 
-DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
+DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")
 	.dt_compat	= sun8i_board_dt_compat,
 	.init_late	= sunxi_dt_cpufreq_init,
 MACHINE_END
-- 
2.3.7

[PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
to other sun8i family SoCs like the A23.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
 arch/arm/mach-sunxi/Kconfig                     | 2 +-
 arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
 3 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index 42941fd..3cb4b94 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -9,4 +9,5 @@ using one of the following compatible strings:
   allwinner,sun6i-a31
   allwinner,sun7i-a20
   allwinner,sun8i-a23
+  allwinner,sun8i-h3
   allwinner,sun9i-a80
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 81502b9..47ac5b4 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -35,7 +35,7 @@ config MACH_SUN7I
 	select SUN5I_HSTIMER
 
 config MACH_SUN8I
-	bool "Allwinner A23 (sun8i) SoCs support"
+	bool "Allwinner A23 / H3 (sun8i) SoCs support"
 	default ARCH_SUNXI
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index 1bc811a..bc63748 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -67,10 +67,11 @@ MACHINE_END
 
 static const char * const sun8i_board_dt_compat[] = {
 	"allwinner,sun8i-a23",
+	"allwinner,sun8i-h3",
 	NULL,
 };
 
-DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
+DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")
 	.dt_compat	= sun8i_board_dt_compat,
 	.init_late	= sunxi_dt_cpufreq_init,
 MACHINE_END
-- 
2.3.7

[PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
to other sun8i family SoCs like the A23.

Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
 arch/arm/mach-sunxi/Kconfig                     | 2 +-
 arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
 3 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index 42941fd..3cb4b94 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -9,4 +9,5 @@ using one of the following compatible strings:
   allwinner,sun6i-a31
   allwinner,sun7i-a20
   allwinner,sun8i-a23
+  allwinner,sun8i-h3
   allwinner,sun9i-a80
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 81502b9..47ac5b4 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -35,7 +35,7 @@ config MACH_SUN7I
 	select SUN5I_HSTIMER
 
 config MACH_SUN8I
-	bool "Allwinner A23 (sun8i) SoCs support"
+	bool "Allwinner A23 / H3 (sun8i) SoCs support"
 	default ARCH_SUNXI
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index 1bc811a..bc63748 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -67,10 +67,11 @@ MACHINE_END
 
 static const char * const sun8i_board_dt_compat[] = {
 	"allwinner,sun8i-a23",
+	"allwinner,sun8i-h3",
 	NULL,
 };
 
-DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
+DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")
 	.dt_compat	= sun8i_board_dt_compat,
 	.init_late	= sunxi_dt_cpufreq_init,
 MACHINE_END
-- 
2.3.7

Re: [PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2407 bytes --]

Hi,

On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
> to other sun8i family SoCs like the A23.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
>  3 files changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> index 42941fd..3cb4b94 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> @@ -9,4 +9,5 @@ using one of the following compatible strings:
>    allwinner,sun6i-a31
>    allwinner,sun7i-a20
>    allwinner,sun8i-a23
> +  allwinner,sun8i-h3
>    allwinner,sun9i-a80
> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> index 81502b9..47ac5b4 100644
> --- a/arch/arm/mach-sunxi/Kconfig
> +++ b/arch/arm/mach-sunxi/Kconfig
> @@ -35,7 +35,7 @@ config MACH_SUN7I
>  	select SUN5I_HSTIMER
>  
>  config MACH_SUN8I
> -	bool "Allwinner A23 (sun8i) SoCs support"
> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"

I'd prefer that we have something similar to sun9i, just mentionning
the family here, instead of an ever-growing list of SoCs.

This used to be easy to maintain, with the new naming scheme, we
already have at least 4 SoCs part of sun8i.

>  	default ARCH_SUNXI
>  	select ARM_GIC
>  	select MFD_SUN6I_PRCM
> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
> index 1bc811a..bc63748 100644
> --- a/arch/arm/mach-sunxi/sunxi.c
> +++ b/arch/arm/mach-sunxi/sunxi.c
> @@ -67,10 +67,11 @@ MACHINE_END
>  
>  static const char * const sun8i_board_dt_compat[] = {
>  	"allwinner,sun8i-a23",
> +	"allwinner,sun8i-h3",
>  	NULL,
>  };
>  
> -DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
> +DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")

Same comment here.

Could you also update Documentation/arm/sunxi/README with these infos
(and ideally, updating it with the new SoCs we've heard about) ?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Maxime Ripard]

Hi,

On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
> to other sun8i family SoCs like the A23.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
>  3 files changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> index 42941fd..3cb4b94 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> @@ -9,4 +9,5 @@ using one of the following compatible strings:
>    allwinner,sun6i-a31
>    allwinner,sun7i-a20
>    allwinner,sun8i-a23
> +  allwinner,sun8i-h3
>    allwinner,sun9i-a80
> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> index 81502b9..47ac5b4 100644
> --- a/arch/arm/mach-sunxi/Kconfig
> +++ b/arch/arm/mach-sunxi/Kconfig
> @@ -35,7 +35,7 @@ config MACH_SUN7I
>  	select SUN5I_HSTIMER
>  
>  config MACH_SUN8I
> -	bool "Allwinner A23 (sun8i) SoCs support"
> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"

I'd prefer that we have something similar to sun9i, just mentionning
the family here, instead of an ever-growing list of SoCs.

This used to be easy to maintain, with the new naming scheme, we
already have at least 4 SoCs part of sun8i.

>  	default ARCH_SUNXI
>  	select ARM_GIC
>  	select MFD_SUN6I_PRCM
> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
> index 1bc811a..bc63748 100644
> --- a/arch/arm/mach-sunxi/sunxi.c
> +++ b/arch/arm/mach-sunxi/sunxi.c
> @@ -67,10 +67,11 @@ MACHINE_END
>  
>  static const char * const sun8i_board_dt_compat[] = {
>  	"allwinner,sun8i-a23",
> +	"allwinner,sun8i-h3",
>  	NULL,
>  };
>  
> -DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
> +DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")

Same comment here.

Could you also update Documentation/arm/sunxi/README with these infos
(and ideally, updating it with the new SoCs we've heard about) ?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150506/f42da871/attachment.sig>

Re: [PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

On 06/05/15 12:04, Maxime Ripard wrote:
> Hi,
> 
> On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
>> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
>> to other sun8i family SoCs like the A23.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
>>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
>>  3 files changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
>> index 42941fd..3cb4b94 100644
>> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
>> @@ -9,4 +9,5 @@ using one of the following compatible strings:
>>    allwinner,sun6i-a31
>>    allwinner,sun7i-a20
>>    allwinner,sun8i-a23
>> +  allwinner,sun8i-h3
>>    allwinner,sun9i-a80
>> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
>> index 81502b9..47ac5b4 100644
>> --- a/arch/arm/mach-sunxi/Kconfig
>> +++ b/arch/arm/mach-sunxi/Kconfig
>> @@ -35,7 +35,7 @@ config MACH_SUN7I
>>  	select SUN5I_HSTIMER
>>  
>>  config MACH_SUN8I
>> -	bool "Allwinner A23 (sun8i) SoCs support"
>> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"
> 
> I'd prefer that we have something similar to sun9i, just mentionning
> the family here, instead of an ever-growing list of SoCs.
> 
> This used to be easy to maintain, with the new naming scheme, we
> already have at least 4 SoCs part of sun8i.

According to Allwinners new naming scheme A20/A31/A31s are also part of
sun8i (sun8iw[1,2]), but I think we can agree to use sun8i for the new
SoCs, starting from A23.

> 
>>  	default ARCH_SUNXI
>>  	select ARM_GIC
>>  	select MFD_SUN6I_PRCM
>> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
>> index 1bc811a..bc63748 100644
>> --- a/arch/arm/mach-sunxi/sunxi.c
>> +++ b/arch/arm/mach-sunxi/sunxi.c
>> @@ -67,10 +67,11 @@ MACHINE_END
>>  
>>  static const char * const sun8i_board_dt_compat[] = {
>>  	"allwinner,sun8i-a23",
>> +	"allwinner,sun8i-h3",
>>  	NULL,
>>  };
>>  
>> -DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
>> +DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")
> 
> Same comment here.
> 
> Could you also update Documentation/arm/sunxi/README with these infos
> (and ideally, updating it with the new SoCs we've heard about) ?
> 

Will do.

Jens

[PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

On 06/05/15 12:04, Maxime Ripard wrote:
> Hi,
> 
> On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
>> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
>> to other sun8i family SoCs like the A23.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
>>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
>>  3 files changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
>> index 42941fd..3cb4b94 100644
>> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
>> @@ -9,4 +9,5 @@ using one of the following compatible strings:
>>    allwinner,sun6i-a31
>>    allwinner,sun7i-a20
>>    allwinner,sun8i-a23
>> +  allwinner,sun8i-h3
>>    allwinner,sun9i-a80
>> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
>> index 81502b9..47ac5b4 100644
>> --- a/arch/arm/mach-sunxi/Kconfig
>> +++ b/arch/arm/mach-sunxi/Kconfig
>> @@ -35,7 +35,7 @@ config MACH_SUN7I
>>  	select SUN5I_HSTIMER
>>  
>>  config MACH_SUN8I
>> -	bool "Allwinner A23 (sun8i) SoCs support"
>> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"
> 
> I'd prefer that we have something similar to sun9i, just mentionning
> the family here, instead of an ever-growing list of SoCs.
> 
> This used to be easy to maintain, with the new naming scheme, we
> already have at least 4 SoCs part of sun8i.

According to Allwinners new naming scheme A20/A31/A31s are also part of
sun8i (sun8iw[1,2]), but I think we can agree to use sun8i for the new
SoCs, starting from A23.

> 
>>  	default ARCH_SUNXI
>>  	select ARM_GIC
>>  	select MFD_SUN6I_PRCM
>> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
>> index 1bc811a..bc63748 100644
>> --- a/arch/arm/mach-sunxi/sunxi.c
>> +++ b/arch/arm/mach-sunxi/sunxi.c
>> @@ -67,10 +67,11 @@ MACHINE_END
>>  
>>  static const char * const sun8i_board_dt_compat[] = {
>>  	"allwinner,sun8i-a23",
>> +	"allwinner,sun8i-h3",
>>  	NULL,
>>  };
>>  
>> -DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
>> +DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")
> 
> Same comment here.
> 
> Could you also update Documentation/arm/sunxi/README with these infos
> (and ideally, updating it with the new SoCs we've heard about) ?
> 

Will do.

Jens

Re: [PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Jens Kuske]

On 06/05/15 12:04, Maxime Ripard wrote:
> Hi,
> 
> On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
>> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
>> to other sun8i family SoCs like the A23.
>>
>> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
>>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
>>  3 files changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
>> index 42941fd..3cb4b94 100644
>> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
>> @@ -9,4 +9,5 @@ using one of the following compatible strings:
>>    allwinner,sun6i-a31
>>    allwinner,sun7i-a20
>>    allwinner,sun8i-a23
>> +  allwinner,sun8i-h3
>>    allwinner,sun9i-a80
>> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
>> index 81502b9..47ac5b4 100644
>> --- a/arch/arm/mach-sunxi/Kconfig
>> +++ b/arch/arm/mach-sunxi/Kconfig
>> @@ -35,7 +35,7 @@ config MACH_SUN7I
>>  	select SUN5I_HSTIMER
>>  
>>  config MACH_SUN8I
>> -	bool "Allwinner A23 (sun8i) SoCs support"
>> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"
> 
> I'd prefer that we have something similar to sun9i, just mentionning
> the family here, instead of an ever-growing list of SoCs.
> 
> This used to be easy to maintain, with the new naming scheme, we
> already have at least 4 SoCs part of sun8i.

According to Allwinners new naming scheme A20/A31/A31s are also part of
sun8i (sun8iw[1,2]), but I think we can agree to use sun8i for the new
SoCs, starting from A23.

> 
>>  	default ARCH_SUNXI
>>  	select ARM_GIC
>>  	select MFD_SUN6I_PRCM
>> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
>> index 1bc811a..bc63748 100644
>> --- a/arch/arm/mach-sunxi/sunxi.c
>> +++ b/arch/arm/mach-sunxi/sunxi.c
>> @@ -67,10 +67,11 @@ MACHINE_END
>>  
>>  static const char * const sun8i_board_dt_compat[] = {
>>  	"allwinner,sun8i-a23",
>> +	"allwinner,sun8i-h3",
>>  	NULL,
>>  };
>>  
>> -DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23) Family")
>> +DT_MACHINE_START(SUN8I_DT, "Allwinner sun8i (A23/H3) Family")
> 
> Same comment here.
> 
> Could you also update Documentation/arm/sunxi/README with these infos
> (and ideally, updating it with the new SoCs we've heard about) ?
> 

Will do.

Jens

Re: [PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2217 bytes --]

On Wed, May 06, 2015 at 12:23:49PM +0200, Jens Kuske wrote:
> On 06/05/15 12:04, Maxime Ripard wrote:
> > Hi,
> > 
> > On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
> >> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
> >> to other sun8i family SoCs like the A23.
> >>
> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> >> ---
> >>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
> >>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
> >>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
> >>  3 files changed, 4 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> >> index 42941fd..3cb4b94 100644
> >> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> >> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> >> @@ -9,4 +9,5 @@ using one of the following compatible strings:
> >>    allwinner,sun6i-a31
> >>    allwinner,sun7i-a20
> >>    allwinner,sun8i-a23
> >> +  allwinner,sun8i-h3
> >>    allwinner,sun9i-a80
> >> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> >> index 81502b9..47ac5b4 100644
> >> --- a/arch/arm/mach-sunxi/Kconfig
> >> +++ b/arch/arm/mach-sunxi/Kconfig
> >> @@ -35,7 +35,7 @@ config MACH_SUN7I
> >>  	select SUN5I_HSTIMER
> >>  
> >>  config MACH_SUN8I
> >> -	bool "Allwinner A23 (sun8i) SoCs support"
> >> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"
> > 
> > I'd prefer that we have something similar to sun9i, just mentionning
> > the family here, instead of an ever-growing list of SoCs.
> > 
> > This used to be easy to maintain, with the new naming scheme, we
> > already have at least 4 SoCs part of sun8i.
> 
> According to Allwinners new naming scheme A20/A31/A31s are also part of
> sun8i (sun8iw[1,2]), but I think we can agree to use sun8i for the new
> SoCs, starting from A23.

Yep, we can't really change the family half-way, and using sun8i for
the newer SoCs (A23, A33, A83, H3, V*, etc.) works just as well.


-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Maxime Ripard]

On Wed, May 06, 2015 at 12:23:49PM +0200, Jens Kuske wrote:
> On 06/05/15 12:04, Maxime Ripard wrote:
> > Hi,
> > 
> > On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
> >> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
> >> to other sun8i family SoCs like the A23.
> >>
> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> >> ---
> >>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
> >>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
> >>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
> >>  3 files changed, 4 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> >> index 42941fd..3cb4b94 100644
> >> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> >> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> >> @@ -9,4 +9,5 @@ using one of the following compatible strings:
> >>    allwinner,sun6i-a31
> >>    allwinner,sun7i-a20
> >>    allwinner,sun8i-a23
> >> +  allwinner,sun8i-h3
> >>    allwinner,sun9i-a80
> >> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> >> index 81502b9..47ac5b4 100644
> >> --- a/arch/arm/mach-sunxi/Kconfig
> >> +++ b/arch/arm/mach-sunxi/Kconfig
> >> @@ -35,7 +35,7 @@ config MACH_SUN7I
> >>  	select SUN5I_HSTIMER
> >>  
> >>  config MACH_SUN8I
> >> -	bool "Allwinner A23 (sun8i) SoCs support"
> >> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"
> > 
> > I'd prefer that we have something similar to sun9i, just mentionning
> > the family here, instead of an ever-growing list of SoCs.
> > 
> > This used to be easy to maintain, with the new naming scheme, we
> > already have at least 4 SoCs part of sun8i.
> 
> According to Allwinners new naming scheme A20/A31/A31s are also part of
> sun8i (sun8iw[1,2]), but I think we can agree to use sun8i for the new
> SoCs, starting from A23.

Yep, we can't really change the family half-way, and using sun8i for
the newer SoCs (A23, A33, A83, H3, V*, etc.) works just as well.


-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150506/32569df5/attachment.sig>

Re: [PATCH 1/6] ARM: sunxi: Introduce Allwinner H3 support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2192 bytes --]

On Wed, May 06, 2015 at 12:23:49PM +0200, Jens Kuske wrote:
> On 06/05/15 12:04, Maxime Ripard wrote:
> > Hi,
> > 
> > On Wed, May 06, 2015 at 11:31:28AM +0200, Jens Kuske wrote:
> >> The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
> >> to other sun8i family SoCs like the A23.
> >>
> >> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> >> ---
> >>  Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
> >>  arch/arm/mach-sunxi/Kconfig                     | 2 +-
> >>  arch/arm/mach-sunxi/sunxi.c                     | 3 ++-
> >>  3 files changed, 4 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> >> index 42941fd..3cb4b94 100644
> >> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> >> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> >> @@ -9,4 +9,5 @@ using one of the following compatible strings:
> >>    allwinner,sun6i-a31
> >>    allwinner,sun7i-a20
> >>    allwinner,sun8i-a23
> >> +  allwinner,sun8i-h3
> >>    allwinner,sun9i-a80
> >> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> >> index 81502b9..47ac5b4 100644
> >> --- a/arch/arm/mach-sunxi/Kconfig
> >> +++ b/arch/arm/mach-sunxi/Kconfig
> >> @@ -35,7 +35,7 @@ config MACH_SUN7I
> >>  	select SUN5I_HSTIMER
> >>  
> >>  config MACH_SUN8I
> >> -	bool "Allwinner A23 (sun8i) SoCs support"
> >> +	bool "Allwinner A23 / H3 (sun8i) SoCs support"
> > 
> > I'd prefer that we have something similar to sun9i, just mentionning
> > the family here, instead of an ever-growing list of SoCs.
> > 
> > This used to be easy to maintain, with the new naming scheme, we
> > already have at least 4 SoCs part of sun8i.
> 
> According to Allwinners new naming scheme A20/A31/A31s are also part of
> sun8i (sun8iw[1,2]), but I think we can agree to use sun8i for the new
> SoCs, starting from A23.

Yep, we can't really change the family half-way, and using sun8i for
the newer SoCs (A23, A33, A83, H3, V*, etc.) works just as well.


-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

The H3 clock control unit is similar to the those of other sun8i family
members like the A23.

The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
being muxable between AHB1 and PLL6/2, but still sharing gate registers.
The documentation isn't totally clear about which devices belong to
AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
kernel source code.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
 drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
 2 files changed, 52 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 4fa11af..4eeb893 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -14,6 +14,8 @@ Required properties:
 	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
 	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
 	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
+	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
+	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
 	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
 	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
 	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
@@ -28,8 +30,11 @@ Required properties:
 	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
 	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
 	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
+	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
 	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
 	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
+	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
+	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
 	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
 	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
 	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
@@ -52,8 +57,10 @@ Required properties:
 	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
 	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
 	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
+	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
 	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
 	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
+	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
 	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
 	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
 	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 7e1e2bd..152a1f7 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
 	.getter = sun5i_a13_get_ahb_factors,
 };
 
+static const struct factors_data sun8i_h3_pll8_data __initconst = {
+	.enable = 31,
+	.table = &sun6i_a31_pll6_config,
+	.getter = sun6i_a31_get_pll6_factors,
+};
+
 static const struct factors_data sun4i_apb1_data __initconst = {
 	.mux = 24,
 	.muxmask = BIT(1) | BIT(0),
@@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
 	.shift = 12,
 };
 
+static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
+	.shift = 0,
+};
+
 static void __init sunxi_mux_clk_setup(struct device_node *node,
 				       struct mux_data *data)
 {
@@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
  * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
  */
 
-#define SUNXI_GATES_MAX_SIZE	64
+#define SUNXI_GATES_MAX_SIZE	160
 
 struct gates_data {
 	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
@@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
 	.mask = {0x25386742, 0x2505111},
 };
 
+static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
+	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
+};
+
 static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
 	.mask = {0xF5F12B},
 };
@@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
 	.mask = {0x9B7},
 };
 
+static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
+	.mask = {0xe0020000},
+};
+
 static const struct gates_data sun4i_apb0_gates_data __initconst = {
 	.mask = {0x4EF},
 };
@@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
 	.mask = {0x3021},
 };
 
+static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
+	.mask = {0x7123},
+};
+
 static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
 	.mask = {0x3F000F},
 };
@@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
 	.mask = {0x1F0007},
 };
 
+static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
+	.mask = {0x1F0007},
+};
+
 static void __init sunxi_gates_clk_setup(struct device_node *node,
 					 struct gates_data *data)
 {
@@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
 	}
 };
 
+static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
+	.factors = &sun6i_a31_pll6_data,
+	.ndivs = 3,
+	.div = {
+		{ .fixed = 2 }, /* normal output, pll6 */
+		{ .self = 1 }, /* base factor clock, pll6 x2 */
+		{ .fixed = 4 }, /* divided output, pll6 /2 */
+	}
+};
+
 /**
  * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
  *
@@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
 	{.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
 	{.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
 	{.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
+	{.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
 	{}
 };
 
@@ -1269,6 +1306,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
 	{.compatible = "allwinner,sun4i-a10-pll5-clk", .data = &pll5_divs_data,},
 	{.compatible = "allwinner,sun4i-a10-pll6-clk", .data = &pll6_divs_data,},
 	{.compatible = "allwinner,sun6i-a31-pll6-clk", .data = &sun6i_a31_pll6_divs_data,},
+	{.compatible = "allwinner,sun8i-h3-pll6-clk", .data = &sun8i_h3_pll6_divs_data,},
 	{}
 };
 
@@ -1276,6 +1314,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
 static const struct of_device_id clk_mux_match[] __initconst = {
 	{.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
 	{.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
 	{}
 };
 
@@ -1288,9 +1327,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
 	{.compatible = "allwinner,sun6i-a31-ahb1-gates-clk", .data = &sun6i_a31_ahb1_gates_data,},
 	{.compatible = "allwinner,sun7i-a20-ahb-gates-clk", .data = &sun7i_a20_ahb_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-ahb1-gates-clk", .data = &sun8i_a23_ahb1_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb1-gates-clk", .data = &sun8i_h3_ahb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb0-gates-clk", .data = &sun9i_a80_ahb0_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb1-gates-clk", .data = &sun9i_a80_ahb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb2-gates-clk", .data = &sun9i_a80_ahb2_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb2-gates-clk", .data = &sun8i_h3_ahb2_gates_data,},
 	{.compatible = "allwinner,sun4i-a10-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
 	{.compatible = "allwinner,sun5i-a10s-apb0-gates-clk", .data = &sun5i_a10s_apb0_gates_data,},
 	{.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
@@ -1302,9 +1343,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
 	{.compatible = "allwinner,sun6i-a31-apb1-gates-clk", .data = &sun6i_a31_apb1_gates_data,},
 	{.compatible = "allwinner,sun7i-a20-apb1-gates-clk", .data = &sun7i_a20_apb1_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-apb1-gates-clk", .data = &sun8i_a23_apb1_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-apb1-gates-clk", .data = &sun8i_h3_apb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-apb1-gates-clk", .data = &sun9i_a80_apb1_gates_data,},
 	{.compatible = "allwinner,sun6i-a31-apb2-gates-clk", .data = &sun6i_a31_apb2_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-apb2-gates-clk", .data = &sun8i_a23_apb2_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-apb2-gates-clk", .data = &sun8i_h3_apb2_gates_data,},
 	{}
 };
 
@@ -1389,6 +1432,7 @@ static void __init sun6i_init_clocks(struct device_node *node)
 CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
 CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
 CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
+CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
 
 static void __init sun9i_init_clocks(struct device_node *node)
 {
-- 
2.3.7

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

The H3 clock control unit is similar to the those of other sun8i family
members like the A23.

The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
being muxable between AHB1 and PLL6/2, but still sharing gate registers.
The documentation isn't totally clear about which devices belong to
AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
kernel source code.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
 drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
 2 files changed, 52 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 4fa11af..4eeb893 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -14,6 +14,8 @@ Required properties:
 	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
 	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
 	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
+	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
+	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
 	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
 	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
 	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
@@ -28,8 +30,11 @@ Required properties:
 	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
 	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
 	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
+	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
 	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
 	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
+	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
+	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
 	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
 	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
 	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
@@ -52,8 +57,10 @@ Required properties:
 	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
 	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
 	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
+	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
 	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
 	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
+	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
 	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
 	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
 	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 7e1e2bd..152a1f7 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
 	.getter = sun5i_a13_get_ahb_factors,
 };
 
+static const struct factors_data sun8i_h3_pll8_data __initconst = {
+	.enable = 31,
+	.table = &sun6i_a31_pll6_config,
+	.getter = sun6i_a31_get_pll6_factors,
+};
+
 static const struct factors_data sun4i_apb1_data __initconst = {
 	.mux = 24,
 	.muxmask = BIT(1) | BIT(0),
@@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
 	.shift = 12,
 };
 
+static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
+	.shift = 0,
+};
+
 static void __init sunxi_mux_clk_setup(struct device_node *node,
 				       struct mux_data *data)
 {
@@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
  * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
  */
 
-#define SUNXI_GATES_MAX_SIZE	64
+#define SUNXI_GATES_MAX_SIZE	160
 
 struct gates_data {
 	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
@@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
 	.mask = {0x25386742, 0x2505111},
 };
 
+static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
+	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
+};
+
 static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
 	.mask = {0xF5F12B},
 };
@@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
 	.mask = {0x9B7},
 };
 
+static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
+	.mask = {0xe0020000},
+};
+
 static const struct gates_data sun4i_apb0_gates_data __initconst = {
 	.mask = {0x4EF},
 };
@@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
 	.mask = {0x3021},
 };
 
+static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
+	.mask = {0x7123},
+};
+
 static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
 	.mask = {0x3F000F},
 };
@@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
 	.mask = {0x1F0007},
 };
 
+static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
+	.mask = {0x1F0007},
+};
+
 static void __init sunxi_gates_clk_setup(struct device_node *node,
 					 struct gates_data *data)
 {
@@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
 	}
 };
 
+static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
+	.factors = &sun6i_a31_pll6_data,
+	.ndivs = 3,
+	.div = {
+		{ .fixed = 2 }, /* normal output, pll6 */
+		{ .self = 1 }, /* base factor clock, pll6 x2 */
+		{ .fixed = 4 }, /* divided output, pll6 /2 */
+	}
+};
+
 /**
  * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
  *
@@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
 	{.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
 	{.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
 	{.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
+	{.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
 	{}
 };
 
@@ -1269,6 +1306,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
 	{.compatible = "allwinner,sun4i-a10-pll5-clk", .data = &pll5_divs_data,},
 	{.compatible = "allwinner,sun4i-a10-pll6-clk", .data = &pll6_divs_data,},
 	{.compatible = "allwinner,sun6i-a31-pll6-clk", .data = &sun6i_a31_pll6_divs_data,},
+	{.compatible = "allwinner,sun8i-h3-pll6-clk", .data = &sun8i_h3_pll6_divs_data,},
 	{}
 };
 
@@ -1276,6 +1314,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
 static const struct of_device_id clk_mux_match[] __initconst = {
 	{.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
 	{.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
 	{}
 };
 
@@ -1288,9 +1327,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
 	{.compatible = "allwinner,sun6i-a31-ahb1-gates-clk", .data = &sun6i_a31_ahb1_gates_data,},
 	{.compatible = "allwinner,sun7i-a20-ahb-gates-clk", .data = &sun7i_a20_ahb_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-ahb1-gates-clk", .data = &sun8i_a23_ahb1_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb1-gates-clk", .data = &sun8i_h3_ahb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb0-gates-clk", .data = &sun9i_a80_ahb0_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb1-gates-clk", .data = &sun9i_a80_ahb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb2-gates-clk", .data = &sun9i_a80_ahb2_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb2-gates-clk", .data = &sun8i_h3_ahb2_gates_data,},
 	{.compatible = "allwinner,sun4i-a10-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
 	{.compatible = "allwinner,sun5i-a10s-apb0-gates-clk", .data = &sun5i_a10s_apb0_gates_data,},
 	{.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
@@ -1302,9 +1343,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
 	{.compatible = "allwinner,sun6i-a31-apb1-gates-clk", .data = &sun6i_a31_apb1_gates_data,},
 	{.compatible = "allwinner,sun7i-a20-apb1-gates-clk", .data = &sun7i_a20_apb1_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-apb1-gates-clk", .data = &sun8i_a23_apb1_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-apb1-gates-clk", .data = &sun8i_h3_apb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-apb1-gates-clk", .data = &sun9i_a80_apb1_gates_data,},
 	{.compatible = "allwinner,sun6i-a31-apb2-gates-clk", .data = &sun6i_a31_apb2_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-apb2-gates-clk", .data = &sun8i_a23_apb2_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-apb2-gates-clk", .data = &sun8i_h3_apb2_gates_data,},
 	{}
 };
 
@@ -1389,6 +1432,7 @@ static void __init sun6i_init_clocks(struct device_node *node)
 CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
 CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
 CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
+CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
 
 static void __init sun9i_init_clocks(struct device_node *node)
 {
-- 
2.3.7

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

The H3 clock control unit is similar to the those of other sun8i family
members like the A23.

The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
being muxable between AHB1 and PLL6/2, but still sharing gate registers.
The documentation isn't totally clear about which devices belong to
AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
kernel source code.

Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
 drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
 2 files changed, 52 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 4fa11af..4eeb893 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -14,6 +14,8 @@ Required properties:
 	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
 	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
 	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
+	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
+	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
 	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
 	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
 	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
@@ -28,8 +30,11 @@ Required properties:
 	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
 	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
 	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
+	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
 	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
 	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
+	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
+	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
 	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
 	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
 	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
@@ -52,8 +57,10 @@ Required properties:
 	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
 	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
 	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
+	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
 	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
 	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
+	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
 	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
 	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
 	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 7e1e2bd..152a1f7 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
 	.getter = sun5i_a13_get_ahb_factors,
 };
 
+static const struct factors_data sun8i_h3_pll8_data __initconst = {
+	.enable = 31,
+	.table = &sun6i_a31_pll6_config,
+	.getter = sun6i_a31_get_pll6_factors,
+};
+
 static const struct factors_data sun4i_apb1_data __initconst = {
 	.mux = 24,
 	.muxmask = BIT(1) | BIT(0),
@@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
 	.shift = 12,
 };
 
+static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
+	.shift = 0,
+};
+
 static void __init sunxi_mux_clk_setup(struct device_node *node,
 				       struct mux_data *data)
 {
@@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
  * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
  */
 
-#define SUNXI_GATES_MAX_SIZE	64
+#define SUNXI_GATES_MAX_SIZE	160
 
 struct gates_data {
 	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
@@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
 	.mask = {0x25386742, 0x2505111},
 };
 
+static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
+	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
+};
+
 static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
 	.mask = {0xF5F12B},
 };
@@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
 	.mask = {0x9B7},
 };
 
+static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
+	.mask = {0xe0020000},
+};
+
 static const struct gates_data sun4i_apb0_gates_data __initconst = {
 	.mask = {0x4EF},
 };
@@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
 	.mask = {0x3021},
 };
 
+static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
+	.mask = {0x7123},
+};
+
 static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
 	.mask = {0x3F000F},
 };
@@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
 	.mask = {0x1F0007},
 };
 
+static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
+	.mask = {0x1F0007},
+};
+
 static void __init sunxi_gates_clk_setup(struct device_node *node,
 					 struct gates_data *data)
 {
@@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
 	}
 };
 
+static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
+	.factors = &sun6i_a31_pll6_data,
+	.ndivs = 3,
+	.div = {
+		{ .fixed = 2 }, /* normal output, pll6 */
+		{ .self = 1 }, /* base factor clock, pll6 x2 */
+		{ .fixed = 4 }, /* divided output, pll6 /2 */
+	}
+};
+
 /**
  * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
  *
@@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
 	{.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
 	{.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
 	{.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
+	{.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
 	{}
 };
 
@@ -1269,6 +1306,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
 	{.compatible = "allwinner,sun4i-a10-pll5-clk", .data = &pll5_divs_data,},
 	{.compatible = "allwinner,sun4i-a10-pll6-clk", .data = &pll6_divs_data,},
 	{.compatible = "allwinner,sun6i-a31-pll6-clk", .data = &sun6i_a31_pll6_divs_data,},
+	{.compatible = "allwinner,sun8i-h3-pll6-clk", .data = &sun8i_h3_pll6_divs_data,},
 	{}
 };
 
@@ -1276,6 +1314,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
 static const struct of_device_id clk_mux_match[] __initconst = {
 	{.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
 	{.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
 	{}
 };
 
@@ -1288,9 +1327,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
 	{.compatible = "allwinner,sun6i-a31-ahb1-gates-clk", .data = &sun6i_a31_ahb1_gates_data,},
 	{.compatible = "allwinner,sun7i-a20-ahb-gates-clk", .data = &sun7i_a20_ahb_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-ahb1-gates-clk", .data = &sun8i_a23_ahb1_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb1-gates-clk", .data = &sun8i_h3_ahb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb0-gates-clk", .data = &sun9i_a80_ahb0_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb1-gates-clk", .data = &sun9i_a80_ahb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-ahb2-gates-clk", .data = &sun9i_a80_ahb2_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-ahb2-gates-clk", .data = &sun8i_h3_ahb2_gates_data,},
 	{.compatible = "allwinner,sun4i-a10-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
 	{.compatible = "allwinner,sun5i-a10s-apb0-gates-clk", .data = &sun5i_a10s_apb0_gates_data,},
 	{.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
@@ -1302,9 +1343,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
 	{.compatible = "allwinner,sun6i-a31-apb1-gates-clk", .data = &sun6i_a31_apb1_gates_data,},
 	{.compatible = "allwinner,sun7i-a20-apb1-gates-clk", .data = &sun7i_a20_apb1_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-apb1-gates-clk", .data = &sun8i_a23_apb1_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-apb1-gates-clk", .data = &sun8i_h3_apb1_gates_data,},
 	{.compatible = "allwinner,sun9i-a80-apb1-gates-clk", .data = &sun9i_a80_apb1_gates_data,},
 	{.compatible = "allwinner,sun6i-a31-apb2-gates-clk", .data = &sun6i_a31_apb2_gates_data,},
 	{.compatible = "allwinner,sun8i-a23-apb2-gates-clk", .data = &sun8i_a23_apb2_gates_data,},
+	{.compatible = "allwinner,sun8i-h3-apb2-gates-clk", .data = &sun8i_h3_apb2_gates_data,},
 	{}
 };
 
@@ -1389,6 +1432,7 @@ static void __init sun6i_init_clocks(struct device_node *node)
 CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
 CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
 CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
+CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
 
 static void __init sun9i_init_clocks(struct device_node *node)
 {
-- 
2.3.7

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Chen-Yu Tsai]

Hi,

On Wed, May 6, 2015 at 5:31 PM, Jens Kuske <jenskuske@gmail.com> wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> The documentation isn't totally clear about which devices belong to
> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>  2 files changed, 52 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 4fa11af..4eeb893 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -14,6 +14,8 @@ Required properties:
>         "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>         "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>         "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> +       "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> +       "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>         "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>         "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>         "allwinner,sun4i-a10-axi-clk" - for the AXI clock
> @@ -28,8 +30,11 @@ Required properties:
>         "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>         "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>         "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> +       "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>         "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>         "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> +       "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> +       "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>         "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>         "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>         "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> @@ -52,8 +57,10 @@ Required properties:
>         "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>         "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>         "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> +       "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>         "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>         "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> +       "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>         "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>         "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>         "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 7e1e2bd..152a1f7 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>         .getter = sun5i_a13_get_ahb_factors,
>  };
>
> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> +       .enable = 31,
> +       .table = &sun6i_a31_pll6_config,
> +       .getter = sun6i_a31_get_pll6_factors,
> +};
> +

If it's fully compatible with sun6i-a31-pll6, please just use it.

On second thought, maybe it's not working because of the .name field?
If so, you're missing one here.

>  static const struct factors_data sun4i_apb1_data __initconst = {
>         .mux = 24,
>         .muxmask = BIT(1) | BIT(0),
> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>         .shift = 12,
>  };
>
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> +       .shift = 0,
> +};
> +
>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>                                        struct mux_data *data)
>  {
> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>   */
>
> -#define SUNXI_GATES_MAX_SIZE   64
> +#define SUNXI_GATES_MAX_SIZE   160
>
>  struct gates_data {
>         DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>         .mask = {0x25386742, 0x2505111},
>  };
>
> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> +       .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> +};
> +

Wow, what's with the hardware design... :|

>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>         .mask = {0xF5F12B},
>  };
> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>         .mask = {0x9B7},
>  };
>
> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> +       .mask = {0xe0020000},
> +};
> +
>  static const struct gates_data sun4i_apb0_gates_data __initconst = {
>         .mask = {0x4EF},
>  };
> @@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
>         .mask = {0x3021},
>  };
>
> +static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
> +       .mask = {0x7123},
> +};
> +
>  static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
>         .mask = {0x3F000F},
>  };
> @@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
>         .mask = {0x1F0007},
>  };
>
> +static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
> +       .mask = {0x1F0007},
> +};
> +
>  static void __init sunxi_gates_clk_setup(struct device_node *node,
>                                          struct gates_data *data)
>  {
> @@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
>         }
>  };
>
> +static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
> +       .factors = &sun6i_a31_pll6_data,
> +       .ndivs = 3,
> +       .div = {
> +               { .fixed = 2 }, /* normal output, pll6 */
> +               { .self = 1 }, /* base factor clock, pll6 x2 */
> +               { .fixed = 4 }, /* divided output, pll6 /2 */

Since you have the luxury of starting a new binding, maybe you could
put the ".self" clock first?

> +       }
> +};
> +
>  /**
>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
>   *
> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},

Matching comment above, no need to add a new compatible for something that's
the same.

ChenYu

>         {}
>  };
>
> @@ -1269,6 +1306,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
>         {.compatible = "allwinner,sun4i-a10-pll5-clk", .data = &pll5_divs_data,},
>         {.compatible = "allwinner,sun4i-a10-pll6-clk", .data = &pll6_divs_data,},
>         {.compatible = "allwinner,sun6i-a31-pll6-clk", .data = &sun6i_a31_pll6_divs_data,},
> +       {.compatible = "allwinner,sun8i-h3-pll6-clk", .data = &sun8i_h3_pll6_divs_data,},
>         {}
>  };
>
> @@ -1276,6 +1314,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
>  static const struct of_device_id clk_mux_match[] __initconst = {
>         {.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
>         {.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
>         {}
>  };
>
> @@ -1288,9 +1327,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
>         {.compatible = "allwinner,sun6i-a31-ahb1-gates-clk", .data = &sun6i_a31_ahb1_gates_data,},
>         {.compatible = "allwinner,sun7i-a20-ahb-gates-clk", .data = &sun7i_a20_ahb_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-ahb1-gates-clk", .data = &sun8i_a23_ahb1_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb1-gates-clk", .data = &sun8i_h3_ahb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb0-gates-clk", .data = &sun9i_a80_ahb0_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb1-gates-clk", .data = &sun9i_a80_ahb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb2-gates-clk", .data = &sun9i_a80_ahb2_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb2-gates-clk", .data = &sun8i_h3_ahb2_gates_data,},
>         {.compatible = "allwinner,sun4i-a10-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
>         {.compatible = "allwinner,sun5i-a10s-apb0-gates-clk", .data = &sun5i_a10s_apb0_gates_data,},
>         {.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
> @@ -1302,9 +1343,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
>         {.compatible = "allwinner,sun6i-a31-apb1-gates-clk", .data = &sun6i_a31_apb1_gates_data,},
>         {.compatible = "allwinner,sun7i-a20-apb1-gates-clk", .data = &sun7i_a20_apb1_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-apb1-gates-clk", .data = &sun8i_a23_apb1_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-apb1-gates-clk", .data = &sun8i_h3_apb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-apb1-gates-clk", .data = &sun9i_a80_apb1_gates_data,},
>         {.compatible = "allwinner,sun6i-a31-apb2-gates-clk", .data = &sun6i_a31_apb2_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-apb2-gates-clk", .data = &sun8i_a23_apb2_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-apb2-gates-clk", .data = &sun8i_h3_apb2_gates_data,},
>         {}
>  };
>
> @@ -1389,6 +1432,7 @@ static void __init sun6i_init_clocks(struct device_node *node)
>  CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
> +CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>
>  static void __init sun9i_init_clocks(struct device_node *node)
>  {
> --
> 2.3.7
>

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Chen-Yu Tsai]

Hi,

On Wed, May 6, 2015 at 5:31 PM, Jens Kuske <jenskuske@gmail.com> wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> The documentation isn't totally clear about which devices belong to
> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>  2 files changed, 52 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 4fa11af..4eeb893 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -14,6 +14,8 @@ Required properties:
>         "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>         "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>         "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> +       "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> +       "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>         "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>         "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>         "allwinner,sun4i-a10-axi-clk" - for the AXI clock
> @@ -28,8 +30,11 @@ Required properties:
>         "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>         "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>         "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> +       "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>         "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>         "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> +       "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> +       "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>         "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>         "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>         "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> @@ -52,8 +57,10 @@ Required properties:
>         "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>         "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>         "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> +       "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>         "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>         "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> +       "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>         "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>         "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>         "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 7e1e2bd..152a1f7 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>         .getter = sun5i_a13_get_ahb_factors,
>  };
>
> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> +       .enable = 31,
> +       .table = &sun6i_a31_pll6_config,
> +       .getter = sun6i_a31_get_pll6_factors,
> +};
> +

If it's fully compatible with sun6i-a31-pll6, please just use it.

On second thought, maybe it's not working because of the .name field?
If so, you're missing one here.

>  static const struct factors_data sun4i_apb1_data __initconst = {
>         .mux = 24,
>         .muxmask = BIT(1) | BIT(0),
> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>         .shift = 12,
>  };
>
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> +       .shift = 0,
> +};
> +
>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>                                        struct mux_data *data)
>  {
> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>   */
>
> -#define SUNXI_GATES_MAX_SIZE   64
> +#define SUNXI_GATES_MAX_SIZE   160
>
>  struct gates_data {
>         DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>         .mask = {0x25386742, 0x2505111},
>  };
>
> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> +       .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> +};
> +

Wow, what's with the hardware design... :|

>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>         .mask = {0xF5F12B},
>  };
> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>         .mask = {0x9B7},
>  };
>
> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> +       .mask = {0xe0020000},
> +};
> +
>  static const struct gates_data sun4i_apb0_gates_data __initconst = {
>         .mask = {0x4EF},
>  };
> @@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
>         .mask = {0x3021},
>  };
>
> +static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
> +       .mask = {0x7123},
> +};
> +
>  static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
>         .mask = {0x3F000F},
>  };
> @@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
>         .mask = {0x1F0007},
>  };
>
> +static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
> +       .mask = {0x1F0007},
> +};
> +
>  static void __init sunxi_gates_clk_setup(struct device_node *node,
>                                          struct gates_data *data)
>  {
> @@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
>         }
>  };
>
> +static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
> +       .factors = &sun6i_a31_pll6_data,
> +       .ndivs = 3,
> +       .div = {
> +               { .fixed = 2 }, /* normal output, pll6 */
> +               { .self = 1 }, /* base factor clock, pll6 x2 */
> +               { .fixed = 4 }, /* divided output, pll6 /2 */

Since you have the luxury of starting a new binding, maybe you could
put the ".self" clock first?

> +       }
> +};
> +
>  /**
>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
>   *
> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},

Matching comment above, no need to add a new compatible for something that's
the same.

ChenYu

>         {}
>  };
>
> @@ -1269,6 +1306,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
>         {.compatible = "allwinner,sun4i-a10-pll5-clk", .data = &pll5_divs_data,},
>         {.compatible = "allwinner,sun4i-a10-pll6-clk", .data = &pll6_divs_data,},
>         {.compatible = "allwinner,sun6i-a31-pll6-clk", .data = &sun6i_a31_pll6_divs_data,},
> +       {.compatible = "allwinner,sun8i-h3-pll6-clk", .data = &sun8i_h3_pll6_divs_data,},
>         {}
>  };
>
> @@ -1276,6 +1314,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
>  static const struct of_device_id clk_mux_match[] __initconst = {
>         {.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
>         {.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
>         {}
>  };
>
> @@ -1288,9 +1327,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
>         {.compatible = "allwinner,sun6i-a31-ahb1-gates-clk", .data = &sun6i_a31_ahb1_gates_data,},
>         {.compatible = "allwinner,sun7i-a20-ahb-gates-clk", .data = &sun7i_a20_ahb_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-ahb1-gates-clk", .data = &sun8i_a23_ahb1_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb1-gates-clk", .data = &sun8i_h3_ahb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb0-gates-clk", .data = &sun9i_a80_ahb0_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb1-gates-clk", .data = &sun9i_a80_ahb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb2-gates-clk", .data = &sun9i_a80_ahb2_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb2-gates-clk", .data = &sun8i_h3_ahb2_gates_data,},
>         {.compatible = "allwinner,sun4i-a10-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
>         {.compatible = "allwinner,sun5i-a10s-apb0-gates-clk", .data = &sun5i_a10s_apb0_gates_data,},
>         {.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
> @@ -1302,9 +1343,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
>         {.compatible = "allwinner,sun6i-a31-apb1-gates-clk", .data = &sun6i_a31_apb1_gates_data,},
>         {.compatible = "allwinner,sun7i-a20-apb1-gates-clk", .data = &sun7i_a20_apb1_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-apb1-gates-clk", .data = &sun8i_a23_apb1_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-apb1-gates-clk", .data = &sun8i_h3_apb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-apb1-gates-clk", .data = &sun9i_a80_apb1_gates_data,},
>         {.compatible = "allwinner,sun6i-a31-apb2-gates-clk", .data = &sun6i_a31_apb2_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-apb2-gates-clk", .data = &sun8i_a23_apb2_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-apb2-gates-clk", .data = &sun8i_h3_apb2_gates_data,},
>         {}
>  };
>
> @@ -1389,6 +1432,7 @@ static void __init sun6i_init_clocks(struct device_node *node)
>  CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
> +CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>
>  static void __init sun9i_init_clocks(struct device_node *node)
>  {
> --
> 2.3.7
>

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Chen-Yu Tsai]

Hi,

On Wed, May 6, 2015 at 5:31 PM, Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> The documentation isn't totally clear about which devices belong to
> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>  2 files changed, 52 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 4fa11af..4eeb893 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -14,6 +14,8 @@ Required properties:
>         "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>         "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>         "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> +       "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> +       "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>         "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>         "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>         "allwinner,sun4i-a10-axi-clk" - for the AXI clock
> @@ -28,8 +30,11 @@ Required properties:
>         "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>         "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>         "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> +       "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>         "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>         "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> +       "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> +       "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>         "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>         "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>         "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> @@ -52,8 +57,10 @@ Required properties:
>         "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>         "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>         "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> +       "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>         "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>         "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> +       "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>         "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>         "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>         "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 7e1e2bd..152a1f7 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>         .getter = sun5i_a13_get_ahb_factors,
>  };
>
> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> +       .enable = 31,
> +       .table = &sun6i_a31_pll6_config,
> +       .getter = sun6i_a31_get_pll6_factors,
> +};
> +

If it's fully compatible with sun6i-a31-pll6, please just use it.

On second thought, maybe it's not working because of the .name field?
If so, you're missing one here.

>  static const struct factors_data sun4i_apb1_data __initconst = {
>         .mux = 24,
>         .muxmask = BIT(1) | BIT(0),
> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>         .shift = 12,
>  };
>
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> +       .shift = 0,
> +};
> +
>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>                                        struct mux_data *data)
>  {
> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>   */
>
> -#define SUNXI_GATES_MAX_SIZE   64
> +#define SUNXI_GATES_MAX_SIZE   160
>
>  struct gates_data {
>         DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>         .mask = {0x25386742, 0x2505111},
>  };
>
> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> +       .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> +};
> +

Wow, what's with the hardware design... :|

>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>         .mask = {0xF5F12B},
>  };
> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>         .mask = {0x9B7},
>  };
>
> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> +       .mask = {0xe0020000},
> +};
> +
>  static const struct gates_data sun4i_apb0_gates_data __initconst = {
>         .mask = {0x4EF},
>  };
> @@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
>         .mask = {0x3021},
>  };
>
> +static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
> +       .mask = {0x7123},
> +};
> +
>  static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
>         .mask = {0x3F000F},
>  };
> @@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
>         .mask = {0x1F0007},
>  };
>
> +static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
> +       .mask = {0x1F0007},
> +};
> +
>  static void __init sunxi_gates_clk_setup(struct device_node *node,
>                                          struct gates_data *data)
>  {
> @@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
>         }
>  };
>
> +static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
> +       .factors = &sun6i_a31_pll6_data,
> +       .ndivs = 3,
> +       .div = {
> +               { .fixed = 2 }, /* normal output, pll6 */
> +               { .self = 1 }, /* base factor clock, pll6 x2 */
> +               { .fixed = 4 }, /* divided output, pll6 /2 */

Since you have the luxury of starting a new binding, maybe you could
put the ".self" clock first?

> +       }
> +};
> +
>  /**
>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
>   *
> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},

Matching comment above, no need to add a new compatible for something that's
the same.

ChenYu

>         {}
>  };
>
> @@ -1269,6 +1306,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
>         {.compatible = "allwinner,sun4i-a10-pll5-clk", .data = &pll5_divs_data,},
>         {.compatible = "allwinner,sun4i-a10-pll6-clk", .data = &pll6_divs_data,},
>         {.compatible = "allwinner,sun6i-a31-pll6-clk", .data = &sun6i_a31_pll6_divs_data,},
> +       {.compatible = "allwinner,sun8i-h3-pll6-clk", .data = &sun8i_h3_pll6_divs_data,},
>         {}
>  };
>
> @@ -1276,6 +1314,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
>  static const struct of_device_id clk_mux_match[] __initconst = {
>         {.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
>         {.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
>         {}
>  };
>
> @@ -1288,9 +1327,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
>         {.compatible = "allwinner,sun6i-a31-ahb1-gates-clk", .data = &sun6i_a31_ahb1_gates_data,},
>         {.compatible = "allwinner,sun7i-a20-ahb-gates-clk", .data = &sun7i_a20_ahb_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-ahb1-gates-clk", .data = &sun8i_a23_ahb1_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb1-gates-clk", .data = &sun8i_h3_ahb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb0-gates-clk", .data = &sun9i_a80_ahb0_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb1-gates-clk", .data = &sun9i_a80_ahb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-ahb2-gates-clk", .data = &sun9i_a80_ahb2_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-ahb2-gates-clk", .data = &sun8i_h3_ahb2_gates_data,},
>         {.compatible = "allwinner,sun4i-a10-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
>         {.compatible = "allwinner,sun5i-a10s-apb0-gates-clk", .data = &sun5i_a10s_apb0_gates_data,},
>         {.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
> @@ -1302,9 +1343,11 @@ static const struct of_device_id clk_gates_match[] __initconst = {
>         {.compatible = "allwinner,sun6i-a31-apb1-gates-clk", .data = &sun6i_a31_apb1_gates_data,},
>         {.compatible = "allwinner,sun7i-a20-apb1-gates-clk", .data = &sun7i_a20_apb1_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-apb1-gates-clk", .data = &sun8i_a23_apb1_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-apb1-gates-clk", .data = &sun8i_h3_apb1_gates_data,},
>         {.compatible = "allwinner,sun9i-a80-apb1-gates-clk", .data = &sun9i_a80_apb1_gates_data,},
>         {.compatible = "allwinner,sun6i-a31-apb2-gates-clk", .data = &sun6i_a31_apb2_gates_data,},
>         {.compatible = "allwinner,sun8i-a23-apb2-gates-clk", .data = &sun8i_a23_apb2_gates_data,},
> +       {.compatible = "allwinner,sun8i-h3-apb2-gates-clk", .data = &sun8i_h3_apb2_gates_data,},
>         {}
>  };
>
> @@ -1389,6 +1432,7 @@ static void __init sun6i_init_clocks(struct device_node *node)
>  CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
>  CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
> +CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>
>  static void __init sun9i_init_clocks(struct device_node *node)
>  {
> --
> 2.3.7
>

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

On 06/05/15 11:47, Chen-Yu Tsai wrote:
> Hi,
> 
> On Wed, May 6, 2015 at 5:31 PM, Jens Kuske <jenskuske@gmail.com> wrote:
>> The H3 clock control unit is similar to the those of other sun8i family
>> members like the A23.
>>
>> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> The documentation isn't totally clear about which devices belong to
>> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> kernel source code.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>>  2 files changed, 52 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 4fa11af..4eeb893 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -14,6 +14,8 @@ Required properties:
>>         "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>>         "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>>         "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> +       "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> +       "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>>         "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>>         "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>>         "allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> @@ -28,8 +30,11 @@ Required properties:
>>         "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>>         "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>>         "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> +       "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>>         "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>>         "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> +       "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> +       "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>>         "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>>         "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>>         "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> @@ -52,8 +57,10 @@ Required properties:
>>         "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>>         "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>>         "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> +       "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>>         "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>>         "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> +       "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>>         "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>>         "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>>         "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 7e1e2bd..152a1f7 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>>         .getter = sun5i_a13_get_ahb_factors,
>>  };
>>
>> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> +       .enable = 31,
>> +       .table = &sun6i_a31_pll6_config,
>> +       .getter = sun6i_a31_get_pll6_factors,
>> +};
>> +
> 
> If it's fully compatible with sun6i-a31-pll6, please just use it.
> 
> On second thought, maybe it's not working because of the .name field?
> If so, you're missing one here.

It complained about the .name field.
But I notice now, the name was correct, it gives us a pll8 running twice
as fast as it should. pll8 doesn't have the x2 output.

So, self-NACK

> 
>>  static const struct factors_data sun4i_apb1_data __initconst = {
>>         .mux = 24,
>>         .muxmask = BIT(1) | BIT(0),
>> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>>         .shift = 12,
>>  };
>>
>> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> +       .shift = 0,
>> +};
>> +
>>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>>                                        struct mux_data *data)
>>  {
>> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>>   */
>>
>> -#define SUNXI_GATES_MAX_SIZE   64
>> +#define SUNXI_GATES_MAX_SIZE   160
>>
>>  struct gates_data {
>>         DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>>         .mask = {0x25386742, 0x2505111},
>>  };
>>
>> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> +       .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> +};
>> +
> 
> Wow, what's with the hardware design... :|

Yeah, I don't like that too, but Allwinner's kernel source says EPHY is
on AHB1.
If anyone has a better idea how to implement this I'm happy to hear it.
Maybe we should simply add a ahb1_gates2 for the new register.

> 
>>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>>         .mask = {0xF5F12B},
>>  };
>> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>>         .mask = {0x9B7},
>>  };
>>
>> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> +       .mask = {0xe0020000},
>> +};
>> +
>>  static const struct gates_data sun4i_apb0_gates_data __initconst = {
>>         .mask = {0x4EF},
>>  };
>> @@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
>>         .mask = {0x3021},
>>  };
>>
>> +static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
>> +       .mask = {0x7123},
>> +};
>> +
>>  static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
>>         .mask = {0x3F000F},
>>  };
>> @@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
>>         .mask = {0x1F0007},
>>  };
>>
>> +static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
>> +       .mask = {0x1F0007},
>> +};
>> +
>>  static void __init sunxi_gates_clk_setup(struct device_node *node,
>>                                          struct gates_data *data)
>>  {
>> @@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
>>         }
>>  };
>>
>> +static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
>> +       .factors = &sun6i_a31_pll6_data,
>> +       .ndivs = 3,
>> +       .div = {
>> +               { .fixed = 2 }, /* normal output, pll6 */
>> +               { .self = 1 }, /* base factor clock, pll6 x2 */
>> +               { .fixed = 4 }, /* divided output, pll6 /2 */
> 
> Since you have the luxury of starting a new binding, maybe you could
> put the ".self" clock first?

I wanted to keep it compatible to the older SoCs, and it felt logical to
have the normal output at first position.

> 
>> +       }
>> +};
>> +
>>  /**
>>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
>>   *
>> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
>>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
>>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
>>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
>> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
> 
> Matching comment above, no need to add a new compatible for something that's
> the same.

PLL8 doesn't have a x2 output according to User Manual, but I did it
wrong anyway, see first comment.

This will need some more work I think.

Jens

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

On 06/05/15 11:47, Chen-Yu Tsai wrote:
> Hi,
> 
> On Wed, May 6, 2015 at 5:31 PM, Jens Kuske <jenskuske@gmail.com> wrote:
>> The H3 clock control unit is similar to the those of other sun8i family
>> members like the A23.
>>
>> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> The documentation isn't totally clear about which devices belong to
>> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> kernel source code.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>>  2 files changed, 52 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 4fa11af..4eeb893 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -14,6 +14,8 @@ Required properties:
>>         "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>>         "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>>         "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> +       "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> +       "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>>         "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>>         "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>>         "allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> @@ -28,8 +30,11 @@ Required properties:
>>         "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>>         "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>>         "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> +       "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>>         "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>>         "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> +       "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> +       "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>>         "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>>         "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>>         "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> @@ -52,8 +57,10 @@ Required properties:
>>         "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>>         "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>>         "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> +       "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>>         "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>>         "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> +       "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>>         "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>>         "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>>         "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 7e1e2bd..152a1f7 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>>         .getter = sun5i_a13_get_ahb_factors,
>>  };
>>
>> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> +       .enable = 31,
>> +       .table = &sun6i_a31_pll6_config,
>> +       .getter = sun6i_a31_get_pll6_factors,
>> +};
>> +
> 
> If it's fully compatible with sun6i-a31-pll6, please just use it.
> 
> On second thought, maybe it's not working because of the .name field?
> If so, you're missing one here.

It complained about the .name field.
But I notice now, the name was correct, it gives us a pll8 running twice
as fast as it should. pll8 doesn't have the x2 output.

So, self-NACK

> 
>>  static const struct factors_data sun4i_apb1_data __initconst = {
>>         .mux = 24,
>>         .muxmask = BIT(1) | BIT(0),
>> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>>         .shift = 12,
>>  };
>>
>> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> +       .shift = 0,
>> +};
>> +
>>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>>                                        struct mux_data *data)
>>  {
>> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>>   */
>>
>> -#define SUNXI_GATES_MAX_SIZE   64
>> +#define SUNXI_GATES_MAX_SIZE   160
>>
>>  struct gates_data {
>>         DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>>         .mask = {0x25386742, 0x2505111},
>>  };
>>
>> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> +       .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> +};
>> +
> 
> Wow, what's with the hardware design... :|

Yeah, I don't like that too, but Allwinner's kernel source says EPHY is
on AHB1.
If anyone has a better idea how to implement this I'm happy to hear it.
Maybe we should simply add a ahb1_gates2 for the new register.

> 
>>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>>         .mask = {0xF5F12B},
>>  };
>> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>>         .mask = {0x9B7},
>>  };
>>
>> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> +       .mask = {0xe0020000},
>> +};
>> +
>>  static const struct gates_data sun4i_apb0_gates_data __initconst = {
>>         .mask = {0x4EF},
>>  };
>> @@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
>>         .mask = {0x3021},
>>  };
>>
>> +static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
>> +       .mask = {0x7123},
>> +};
>> +
>>  static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
>>         .mask = {0x3F000F},
>>  };
>> @@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
>>         .mask = {0x1F0007},
>>  };
>>
>> +static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
>> +       .mask = {0x1F0007},
>> +};
>> +
>>  static void __init sunxi_gates_clk_setup(struct device_node *node,
>>                                          struct gates_data *data)
>>  {
>> @@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
>>         }
>>  };
>>
>> +static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
>> +       .factors = &sun6i_a31_pll6_data,
>> +       .ndivs = 3,
>> +       .div = {
>> +               { .fixed = 2 }, /* normal output, pll6 */
>> +               { .self = 1 }, /* base factor clock, pll6 x2 */
>> +               { .fixed = 4 }, /* divided output, pll6 /2 */
> 
> Since you have the luxury of starting a new binding, maybe you could
> put the ".self" clock first?

I wanted to keep it compatible to the older SoCs, and it felt logical to
have the normal output at first position.

> 
>> +       }
>> +};
>> +
>>  /**
>>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
>>   *
>> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
>>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
>>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
>>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
>> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
> 
> Matching comment above, no need to add a new compatible for something that's
> the same.

PLL8 doesn't have a x2 output according to User Manual, but I did it
wrong anyway, see first comment.

This will need some more work I think.

Jens

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

On 06/05/15 11:47, Chen-Yu Tsai wrote:
> Hi,
> 
> On Wed, May 6, 2015 at 5:31 PM, Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>> The H3 clock control unit is similar to the those of other sun8i family
>> members like the A23.
>>
>> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> The documentation isn't totally clear about which devices belong to
>> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> kernel source code.
>>
>> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>>  2 files changed, 52 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 4fa11af..4eeb893 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -14,6 +14,8 @@ Required properties:
>>         "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>>         "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>>         "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> +       "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> +       "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>>         "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>>         "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>>         "allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> @@ -28,8 +30,11 @@ Required properties:
>>         "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>>         "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>>         "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> +       "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>>         "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>>         "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> +       "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> +       "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>>         "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>>         "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>>         "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> @@ -52,8 +57,10 @@ Required properties:
>>         "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>>         "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>>         "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> +       "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>>         "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>>         "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> +       "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>>         "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>>         "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>>         "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 7e1e2bd..152a1f7 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>>         .getter = sun5i_a13_get_ahb_factors,
>>  };
>>
>> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> +       .enable = 31,
>> +       .table = &sun6i_a31_pll6_config,
>> +       .getter = sun6i_a31_get_pll6_factors,
>> +};
>> +
> 
> If it's fully compatible with sun6i-a31-pll6, please just use it.
> 
> On second thought, maybe it's not working because of the .name field?
> If so, you're missing one here.

It complained about the .name field.
But I notice now, the name was correct, it gives us a pll8 running twice
as fast as it should. pll8 doesn't have the x2 output.

So, self-NACK

> 
>>  static const struct factors_data sun4i_apb1_data __initconst = {
>>         .mux = 24,
>>         .muxmask = BIT(1) | BIT(0),
>> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>>         .shift = 12,
>>  };
>>
>> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> +       .shift = 0,
>> +};
>> +
>>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>>                                        struct mux_data *data)
>>  {
>> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>>   */
>>
>> -#define SUNXI_GATES_MAX_SIZE   64
>> +#define SUNXI_GATES_MAX_SIZE   160
>>
>>  struct gates_data {
>>         DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>>         .mask = {0x25386742, 0x2505111},
>>  };
>>
>> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> +       .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> +};
>> +
> 
> Wow, what's with the hardware design... :|

Yeah, I don't like that too, but Allwinner's kernel source says EPHY is
on AHB1.
If anyone has a better idea how to implement this I'm happy to hear it.
Maybe we should simply add a ahb1_gates2 for the new register.

> 
>>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>>         .mask = {0xF5F12B},
>>  };
>> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>>         .mask = {0x9B7},
>>  };
>>
>> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> +       .mask = {0xe0020000},
>> +};
>> +
>>  static const struct gates_data sun4i_apb0_gates_data __initconst = {
>>         .mask = {0x4EF},
>>  };
>> @@ -978,6 +996,10 @@ static const struct gates_data sun8i_a23_apb1_gates_data __initconst = {
>>         .mask = {0x3021},
>>  };
>>
>> +static const struct gates_data sun8i_h3_apb1_gates_data __initconst = {
>> +       .mask = {0x7123},
>> +};
>> +
>>  static const struct gates_data sun6i_a31_apb2_gates_data __initconst = {
>>         .mask = {0x3F000F},
>>  };
>> @@ -994,6 +1016,10 @@ static const struct gates_data sun8i_a23_apb2_gates_data __initconst = {
>>         .mask = {0x1F0007},
>>  };
>>
>> +static const struct gates_data sun8i_h3_apb2_gates_data __initconst = {
>> +       .mask = {0x1F0007},
>> +};
>> +
>>  static void __init sunxi_gates_clk_setup(struct device_node *node,
>>                                          struct gates_data *data)
>>  {
>> @@ -1106,6 +1132,16 @@ static const struct divs_data sun6i_a31_pll6_divs_data __initconst = {
>>         }
>>  };
>>
>> +static const struct divs_data sun8i_h3_pll6_divs_data __initconst = {
>> +       .factors = &sun6i_a31_pll6_data,
>> +       .ndivs = 3,
>> +       .div = {
>> +               { .fixed = 2 }, /* normal output, pll6 */
>> +               { .self = 1 }, /* base factor clock, pll6 x2 */
>> +               { .fixed = 4 }, /* divided output, pll6 /2 */
> 
> Since you have the luxury of starting a new binding, maybe you could
> put the ".self" clock first?

I wanted to keep it compatible to the older SoCs, and it felt logical to
have the normal output at first position.

> 
>> +       }
>> +};
>> +
>>  /**
>>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
>>   *
>> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
>>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
>>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
>>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
>> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
> 
> Matching comment above, no need to add a new compatible for something that's
> the same.

PLL8 doesn't have a x2 output according to User Manual, but I did it
wrong anyway, see first comment.

This will need some more work I think.

Jens

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1180 bytes --]

On Wed, May 06, 2015 at 12:18:11PM +0200, Jens Kuske wrote:
> >>  /**
> >>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
> >>   *
> >> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
> >>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
> >>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
> >>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
> >> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
> > 
> > Matching comment above, no need to add a new compatible for something that's
> > the same.
> 
> PLL8 doesn't have a x2 output according to User Manual, but I did it
> wrong anyway, see first comment.

Don't worry too much about that output.

It's not really an output, it's a pre-multiplier on a single
child. We're discussing with Chen-Yu about refactoring this anyway, so
it will probably go away in a near future.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

On Wed, May 06, 2015 at 12:18:11PM +0200, Jens Kuske wrote:
> >>  /**
> >>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
> >>   *
> >> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
> >>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
> >>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
> >>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
> >> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
> > 
> > Matching comment above, no need to add a new compatible for something that's
> > the same.
> 
> PLL8 doesn't have a x2 output according to User Manual, but I did it
> wrong anyway, see first comment.

Don't worry too much about that output.

It's not really an output, it's a pre-multiplier on a single
child. We're discussing with Chen-Yu about refactoring this anyway, so
it will probably go away in a near future.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150509/ef264412/attachment-0001.sig>

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1151 bytes --]

On Wed, May 06, 2015 at 12:18:11PM +0200, Jens Kuske wrote:
> >>  /**
> >>   * sunxi_divs_clk_setup() - Setup function for leaf divisors on clocks
> >>   *
> >> @@ -1252,6 +1288,7 @@ static const struct of_device_id clk_factors_match[] __initconst = {
> >>         {.compatible = "allwinner,sun5i-a13-ahb-clk", .data = &sun5i_a13_ahb_data,},
> >>         {.compatible = "allwinner,sun4i-a10-apb1-clk", .data = &sun4i_apb1_data,},
> >>         {.compatible = "allwinner,sun7i-a20-out-clk", .data = &sun7i_a20_out_data,},
> >> +       {.compatible = "allwinner,sun8i-h3-pll8-clk", .data = &sun8i_h3_pll8_data,},
> > 
> > Matching comment above, no need to add a new compatible for something that's
> > the same.
> 
> PLL8 doesn't have a x2 output according to User Manual, but I did it
> wrong anyway, see first comment.

Don't worry too much about that output.

It's not really an output, it's a pre-multiplier on a single
child. We're discussing with Chen-Yu about refactoring this anyway, so
it will probably go away in a near future.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 5954 bytes --]

On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
> 
> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> The documentation isn't totally clear about which devices belong to
> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> kernel source code.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>  2 files changed, 52 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 4fa11af..4eeb893 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -14,6 +14,8 @@ Required properties:
>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
> @@ -28,8 +30,11 @@ Required properties:
>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> @@ -52,8 +57,10 @@ Required properties:
>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 7e1e2bd..152a1f7 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>  	.getter = sun5i_a13_get_ahb_factors,
>  };
>  
> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> +	.enable = 31,
> +	.table = &sun6i_a31_pll6_config,
> +	.getter = sun6i_a31_get_pll6_factors,
> +};

This looks like it's just another instance of the A31 pll6.

In such a case, we don't need to declare a new driver, just reuse the
same compatible.

>  static const struct factors_data sun4i_apb1_data __initconst = {
>  	.mux = 24,
>  	.muxmask = BIT(1) | BIT(0),
> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>  	.shift = 12,
>  };
>  
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> +	.shift = 0,
> +};
> +
>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>  				       struct mux_data *data)
>  {
> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>   */
>  
> -#define SUNXI_GATES_MAX_SIZE	64
> +#define SUNXI_GATES_MAX_SIZE	160
>  
>  struct gates_data {
>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>  	.mask = {0x25386742, 0x2505111},
>  };
>  
> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> +};
> +

Judging from the user manual, there's a few gates in those 0
registers, is this normal that you don't support them?

>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>  	.mask = {0xF5F12B},
>  };
> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>  	.mask = {0x9B7},
>  };
>  
> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> +	.mask = {0xe0020000},
> +};
> +

I don't think we should split the ahb1 and ahb2 gates here. It really
looks like it's the same controller.

The way I'm seeing it would be to have a single clock driver that
would handle both your ahb1 and ahb2 gates.

It would take two parents, ahb1 and ahb2, obviously, and would take
register depending on the gate w'ere registering either the ahb1 or
the ahb2 parent.

It seems like there's only a handful of devices in ahb2 anyway, so
that wouldn't make a very long list of devices to declare as childs of
ahb2.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
> 
> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> The documentation isn't totally clear about which devices belong to
> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> kernel source code.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>  2 files changed, 52 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 4fa11af..4eeb893 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -14,6 +14,8 @@ Required properties:
>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
> @@ -28,8 +30,11 @@ Required properties:
>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> @@ -52,8 +57,10 @@ Required properties:
>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 7e1e2bd..152a1f7 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>  	.getter = sun5i_a13_get_ahb_factors,
>  };
>  
> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> +	.enable = 31,
> +	.table = &sun6i_a31_pll6_config,
> +	.getter = sun6i_a31_get_pll6_factors,
> +};

This looks like it's just another instance of the A31 pll6.

In such a case, we don't need to declare a new driver, just reuse the
same compatible.

>  static const struct factors_data sun4i_apb1_data __initconst = {
>  	.mux = 24,
>  	.muxmask = BIT(1) | BIT(0),
> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>  	.shift = 12,
>  };
>  
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> +	.shift = 0,
> +};
> +
>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>  				       struct mux_data *data)
>  {
> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>   */
>  
> -#define SUNXI_GATES_MAX_SIZE	64
> +#define SUNXI_GATES_MAX_SIZE	160
>  
>  struct gates_data {
>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>  	.mask = {0x25386742, 0x2505111},
>  };
>  
> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> +};
> +

Judging from the user manual, there's a few gates in those 0
registers, is this normal that you don't support them?

>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>  	.mask = {0xF5F12B},
>  };
> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>  	.mask = {0x9B7},
>  };
>  
> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> +	.mask = {0xe0020000},
> +};
> +

I don't think we should split the ahb1 and ahb2 gates here. It really
looks like it's the same controller.

The way I'm seeing it would be to have a single clock driver that
would handle both your ahb1 and ahb2 gates.

It would take two parents, ahb1 and ahb2, obviously, and would take
register depending on the gate w'ere registering either the ahb1 or
the ahb2 parent.

It seems like there's only a handful of devices in ahb2 anyway, so
that wouldn't make a very long list of devices to declare as childs of
ahb2.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150509/eef29d5e/attachment-0001.sig>

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 5844 bytes --]

On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
> 
> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> The documentation isn't totally clear about which devices belong to
> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> kernel source code.
> 
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>  2 files changed, 52 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 4fa11af..4eeb893 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -14,6 +14,8 @@ Required properties:
>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
> @@ -28,8 +30,11 @@ Required properties:
>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> @@ -52,8 +57,10 @@ Required properties:
>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 7e1e2bd..152a1f7 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>  	.getter = sun5i_a13_get_ahb_factors,
>  };
>  
> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> +	.enable = 31,
> +	.table = &sun6i_a31_pll6_config,
> +	.getter = sun6i_a31_get_pll6_factors,
> +};

This looks like it's just another instance of the A31 pll6.

In such a case, we don't need to declare a new driver, just reuse the
same compatible.

>  static const struct factors_data sun4i_apb1_data __initconst = {
>  	.mux = 24,
>  	.muxmask = BIT(1) | BIT(0),
> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>  	.shift = 12,
>  };
>  
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> +	.shift = 0,
> +};
> +
>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>  				       struct mux_data *data)
>  {
> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>   */
>  
> -#define SUNXI_GATES_MAX_SIZE	64
> +#define SUNXI_GATES_MAX_SIZE	160
>  
>  struct gates_data {
>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>  	.mask = {0x25386742, 0x2505111},
>  };
>  
> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> +};
> +

Judging from the user manual, there's a few gates in those 0
registers, is this normal that you don't support them?

>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>  	.mask = {0xF5F12B},
>  };
> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>  	.mask = {0x9B7},
>  };
>  
> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> +	.mask = {0xe0020000},
> +};
> +

I don't think we should split the ahb1 and ahb2 gates here. It really
looks like it's the same controller.

The way I'm seeing it would be to have a single clock driver that
would handle both your ahb1 and ahb2 gates.

It would take two parents, ahb1 and ahb2, obviously, and would take
register depending on the gate w'ere registering either the ahb1 or
the ahb2 parent.

It seems like there's only a handful of devices in ahb2 anyway, so
that wouldn't make a very long list of devices to declare as childs of
ahb2.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

Hi,

On 09/05/15 13:27, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
>> The H3 clock control unit is similar to the those of other sun8i family
>> members like the A23.
>>
>> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> The documentation isn't totally clear about which devices belong to
>> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> kernel source code.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>>  2 files changed, 52 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 4fa11af..4eeb893 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -14,6 +14,8 @@ Required properties:
>>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> @@ -28,8 +30,11 @@ Required properties:
>>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> @@ -52,8 +57,10 @@ Required properties:
>>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 7e1e2bd..152a1f7 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>>  	.getter = sun5i_a13_get_ahb_factors,
>>  };
>>  
>> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> +	.enable = 31,
>> +	.table = &sun6i_a31_pll6_config,
>> +	.getter = sun6i_a31_get_pll6_factors,
>> +};
> 
> This looks like it's just another instance of the A31 pll6.
> 
> In such a case, we don't need to declare a new driver, just reuse the
> same compatible.

If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
field, already existing clock or something like that. (And pll8 doesn't
even have a x2 version)

> 
>>  static const struct factors_data sun4i_apb1_data __initconst = {
>>  	.mux = 24,
>>  	.muxmask = BIT(1) | BIT(0),
>> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>>  	.shift = 12,
>>  };
>>  
>> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> +	.shift = 0,
>> +};
>> +
>>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>>  				       struct mux_data *data)
>>  {
>> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>>   */
>>  
>> -#define SUNXI_GATES_MAX_SIZE	64
>> +#define SUNXI_GATES_MAX_SIZE	160
>>  
>>  struct gates_data {
>>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>>  	.mask = {0x25386742, 0x2505111},
>>  };
>>  
>> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> +};
>> +
> 
> Judging from the user manual, there's a few gates in those 0
> registers, is this normal that you don't support them?

They are holes for apb1 and apb2. Which is actually pretty ugly.

> 
>>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>>  	.mask = {0xF5F12B},
>>  };
>> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>>  	.mask = {0x9B7},
>>  };
>>  
>> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> +	.mask = {0xe0020000},
>> +};
>> +
> 
> I don't think we should split the ahb1 and ahb2 gates here. It really
> looks like it's the same controller.
> 
> The way I'm seeing it would be to have a single clock driver that
> would handle both your ahb1 and ahb2 gates.
> 
> It would take two parents, ahb1 and ahb2, obviously, and would take
> register depending on the gate w'ere registering either the ahb1 or
> the ahb2 parent.
> 
> It seems like there's only a handful of devices in ahb2 anyway, so
> that wouldn't make a very long list of devices to declare as childs of
> ahb2.
> 

I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
and apb2 gates, as it is done in the user manual.

But it would need a pretty big parents array and result in big gate
numbers in devicetree, <&bus_gates 112> for uart0 for example.

Would this be ok?

Jens

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

Hi,

On 09/05/15 13:27, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
>> The H3 clock control unit is similar to the those of other sun8i family
>> members like the A23.
>>
>> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> The documentation isn't totally clear about which devices belong to
>> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> kernel source code.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>>  2 files changed, 52 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 4fa11af..4eeb893 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -14,6 +14,8 @@ Required properties:
>>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> @@ -28,8 +30,11 @@ Required properties:
>>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> @@ -52,8 +57,10 @@ Required properties:
>>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 7e1e2bd..152a1f7 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>>  	.getter = sun5i_a13_get_ahb_factors,
>>  };
>>  
>> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> +	.enable = 31,
>> +	.table = &sun6i_a31_pll6_config,
>> +	.getter = sun6i_a31_get_pll6_factors,
>> +};
> 
> This looks like it's just another instance of the A31 pll6.
> 
> In such a case, we don't need to declare a new driver, just reuse the
> same compatible.

If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
field, already existing clock or something like that. (And pll8 doesn't
even have a x2 version)

> 
>>  static const struct factors_data sun4i_apb1_data __initconst = {
>>  	.mux = 24,
>>  	.muxmask = BIT(1) | BIT(0),
>> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>>  	.shift = 12,
>>  };
>>  
>> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> +	.shift = 0,
>> +};
>> +
>>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>>  				       struct mux_data *data)
>>  {
>> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>>   */
>>  
>> -#define SUNXI_GATES_MAX_SIZE	64
>> +#define SUNXI_GATES_MAX_SIZE	160
>>  
>>  struct gates_data {
>>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>>  	.mask = {0x25386742, 0x2505111},
>>  };
>>  
>> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> +};
>> +
> 
> Judging from the user manual, there's a few gates in those 0
> registers, is this normal that you don't support them?

They are holes for apb1 and apb2. Which is actually pretty ugly.

> 
>>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>>  	.mask = {0xF5F12B},
>>  };
>> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>>  	.mask = {0x9B7},
>>  };
>>  
>> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> +	.mask = {0xe0020000},
>> +};
>> +
> 
> I don't think we should split the ahb1 and ahb2 gates here. It really
> looks like it's the same controller.
> 
> The way I'm seeing it would be to have a single clock driver that
> would handle both your ahb1 and ahb2 gates.
> 
> It would take two parents, ahb1 and ahb2, obviously, and would take
> register depending on the gate w'ere registering either the ahb1 or
> the ahb2 parent.
> 
> It seems like there's only a handful of devices in ahb2 anyway, so
> that wouldn't make a very long list of devices to declare as childs of
> ahb2.
> 

I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
and apb2 gates, as it is done in the user manual.

But it would need a pretty big parents array and result in big gate
numbers in devicetree, <&bus_gates 112> for uart0 for example.

Would this be ok?

Jens

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Jens Kuske]

Hi,

On 09/05/15 13:27, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
>> The H3 clock control unit is similar to the those of other sun8i family
>> members like the A23.
>>
>> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> The documentation isn't totally clear about which devices belong to
>> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> kernel source code.
>>
>> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>>  2 files changed, 52 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 4fa11af..4eeb893 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -14,6 +14,8 @@ Required properties:
>>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> @@ -28,8 +30,11 @@ Required properties:
>>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> @@ -52,8 +57,10 @@ Required properties:
>>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 7e1e2bd..152a1f7 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>>  	.getter = sun5i_a13_get_ahb_factors,
>>  };
>>  
>> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> +	.enable = 31,
>> +	.table = &sun6i_a31_pll6_config,
>> +	.getter = sun6i_a31_get_pll6_factors,
>> +};
> 
> This looks like it's just another instance of the A31 pll6.
> 
> In such a case, we don't need to declare a new driver, just reuse the
> same compatible.

If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
field, already existing clock or something like that. (And pll8 doesn't
even have a x2 version)

> 
>>  static const struct factors_data sun4i_apb1_data __initconst = {
>>  	.mux = 24,
>>  	.muxmask = BIT(1) | BIT(0),
>> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>>  	.shift = 12,
>>  };
>>  
>> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> +	.shift = 0,
>> +};
>> +
>>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>>  				       struct mux_data *data)
>>  {
>> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>>   */
>>  
>> -#define SUNXI_GATES_MAX_SIZE	64
>> +#define SUNXI_GATES_MAX_SIZE	160
>>  
>>  struct gates_data {
>>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>>  	.mask = {0x25386742, 0x2505111},
>>  };
>>  
>> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> +};
>> +
> 
> Judging from the user manual, there's a few gates in those 0
> registers, is this normal that you don't support them?

They are holes for apb1 and apb2. Which is actually pretty ugly.

> 
>>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>>  	.mask = {0xF5F12B},
>>  };
>> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>>  	.mask = {0x9B7},
>>  };
>>  
>> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> +	.mask = {0xe0020000},
>> +};
>> +
> 
> I don't think we should split the ahb1 and ahb2 gates here. It really
> looks like it's the same controller.
> 
> The way I'm seeing it would be to have a single clock driver that
> would handle both your ahb1 and ahb2 gates.
> 
> It would take two parents, ahb1 and ahb2, obviously, and would take
> register depending on the gate w'ere registering either the ahb1 or
> the ahb2 parent.
> 
> It seems like there's only a handful of devices in ahb2 anyway, so
> that wouldn't make a very long list of devices to declare as childs of
> ahb2.
> 

I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
and apb2 gates, as it is done in the user manual.

But it would need a pretty big parents array and result in big gate
numbers in devicetree, <&bus_gates 112> for uart0 for example.

Would this be ok?

Jens

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 7405 bytes --]

Hi,

On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
> On 09/05/15 13:27, Maxime Ripard wrote:
> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> >> The H3 clock control unit is similar to the those of other sun8i family
> >> members like the A23.
> >>
> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> >> The documentation isn't totally clear about which devices belong to
> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> >> kernel source code.
> >>
> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> >> ---
> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
> >>  2 files changed, 52 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> index 4fa11af..4eeb893 100644
> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> @@ -14,6 +14,8 @@ Required properties:
> >>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
> >>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
> >>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> >> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> >> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
> >>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
> >>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
> >>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
> >> @@ -28,8 +30,11 @@ Required properties:
> >>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
> >>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> >>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> >> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> >>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> >>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> >> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> >> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
> >>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> >>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
> >>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> >> @@ -52,8 +57,10 @@ Required properties:
> >>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
> >>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
> >>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> >> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
> >>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> >>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> >> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
> >>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> >>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> >>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> >> index 7e1e2bd..152a1f7 100644
> >> --- a/drivers/clk/sunxi/clk-sunxi.c
> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
> >>  	.getter = sun5i_a13_get_ahb_factors,
> >>  };
> >>  
> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> >> +	.enable = 31,
> >> +	.table = &sun6i_a31_pll6_config,
> >> +	.getter = sun6i_a31_get_pll6_factors,
> >> +};
> > 
> > This looks like it's just another instance of the A31 pll6.
> > 
> > In such a case, we don't need to declare a new driver, just reuse the
> > same compatible.
> 
> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
> field, already existing clock or something like that.

Damn. You're obviously right...

Could you add a TODO comment on top then? just so that we know that we
need to merge this clock with pll6?

> (And pll8 doesn't even have a x2 version)

Judging by the H3 datasheet, it does.

> >>  static const struct factors_data sun4i_apb1_data __initconst = {
> >>  	.mux = 24,
> >>  	.muxmask = BIT(1) | BIT(0),
> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> >>  	.shift = 12,
> >>  };
> >>  
> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> >> +	.shift = 0,
> >> +};
> >> +
> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
> >>  				       struct mux_data *data)
> >>  {
> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
> >>   */
> >>  
> >> -#define SUNXI_GATES_MAX_SIZE	64
> >> +#define SUNXI_GATES_MAX_SIZE	160
> >>  
> >>  struct gates_data {
> >>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
> >>  	.mask = {0x25386742, 0x2505111},
> >>  };
> >>  
> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> >> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> >> +};
> >> +
> > 
> > Judging from the user manual, there's a few gates in those 0
> > registers, is this normal that you don't support them?
> 
> They are holes for apb1 and apb2. Which is actually pretty ugly.

Ah, right.

So I guess it's completely related to the discussion below.

> >>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
> >>  	.mask = {0xF5F12B},
> >>  };
> >> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
> >>  	.mask = {0x9B7},
> >>  };
> >>  
> >> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> >> +	.mask = {0xe0020000},
> >> +};
> >> +
> > 
> > I don't think we should split the ahb1 and ahb2 gates here. It really
> > looks like it's the same controller.
> > 
> > The way I'm seeing it would be to have a single clock driver that
> > would handle both your ahb1 and ahb2 gates.
> > 
> > It would take two parents, ahb1 and ahb2, obviously, and would take
> > register depending on the gate w'ere registering either the ahb1 or
> > the ahb2 parent.
> > 
> > It seems like there's only a handful of devices in ahb2 anyway, so
> > that wouldn't make a very long list of devices to declare as childs of
> > ahb2.
> > 
> 
> I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
> and apb2 gates, as it is done in the user manual.
> 
> But it would need a pretty big parents array and result in big gate
> numbers in devicetree, <&bus_gates 112> for uart0 for example.
> 
> Would this be ok?

I don't see anything wrong with that, as long as we have a clear
documentation stating where that number comes from.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

Hi,

On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
> On 09/05/15 13:27, Maxime Ripard wrote:
> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> >> The H3 clock control unit is similar to the those of other sun8i family
> >> members like the A23.
> >>
> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> >> The documentation isn't totally clear about which devices belong to
> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> >> kernel source code.
> >>
> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> >> ---
> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
> >>  2 files changed, 52 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> index 4fa11af..4eeb893 100644
> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> @@ -14,6 +14,8 @@ Required properties:
> >>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
> >>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
> >>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> >> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> >> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
> >>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
> >>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
> >>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
> >> @@ -28,8 +30,11 @@ Required properties:
> >>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
> >>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> >>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> >> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> >>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> >>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> >> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> >> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
> >>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> >>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
> >>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> >> @@ -52,8 +57,10 @@ Required properties:
> >>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
> >>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
> >>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> >> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
> >>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> >>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> >> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
> >>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> >>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> >>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> >> index 7e1e2bd..152a1f7 100644
> >> --- a/drivers/clk/sunxi/clk-sunxi.c
> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
> >>  	.getter = sun5i_a13_get_ahb_factors,
> >>  };
> >>  
> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> >> +	.enable = 31,
> >> +	.table = &sun6i_a31_pll6_config,
> >> +	.getter = sun6i_a31_get_pll6_factors,
> >> +};
> > 
> > This looks like it's just another instance of the A31 pll6.
> > 
> > In such a case, we don't need to declare a new driver, just reuse the
> > same compatible.
> 
> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
> field, already existing clock or something like that.

Damn. You're obviously right...

Could you add a TODO comment on top then? just so that we know that we
need to merge this clock with pll6?

> (And pll8 doesn't even have a x2 version)

Judging by the H3 datasheet, it does.

> >>  static const struct factors_data sun4i_apb1_data __initconst = {
> >>  	.mux = 24,
> >>  	.muxmask = BIT(1) | BIT(0),
> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> >>  	.shift = 12,
> >>  };
> >>  
> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> >> +	.shift = 0,
> >> +};
> >> +
> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
> >>  				       struct mux_data *data)
> >>  {
> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
> >>   */
> >>  
> >> -#define SUNXI_GATES_MAX_SIZE	64
> >> +#define SUNXI_GATES_MAX_SIZE	160
> >>  
> >>  struct gates_data {
> >>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
> >>  	.mask = {0x25386742, 0x2505111},
> >>  };
> >>  
> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> >> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> >> +};
> >> +
> > 
> > Judging from the user manual, there's a few gates in those 0
> > registers, is this normal that you don't support them?
> 
> They are holes for apb1 and apb2. Which is actually pretty ugly.

Ah, right.

So I guess it's completely related to the discussion below.

> >>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
> >>  	.mask = {0xF5F12B},
> >>  };
> >> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
> >>  	.mask = {0x9B7},
> >>  };
> >>  
> >> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> >> +	.mask = {0xe0020000},
> >> +};
> >> +
> > 
> > I don't think we should split the ahb1 and ahb2 gates here. It really
> > looks like it's the same controller.
> > 
> > The way I'm seeing it would be to have a single clock driver that
> > would handle both your ahb1 and ahb2 gates.
> > 
> > It would take two parents, ahb1 and ahb2, obviously, and would take
> > register depending on the gate w'ere registering either the ahb1 or
> > the ahb2 parent.
> > 
> > It seems like there's only a handful of devices in ahb2 anyway, so
> > that wouldn't make a very long list of devices to declare as childs of
> > ahb2.
> > 
> 
> I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
> and apb2 gates, as it is done in the user manual.
> 
> But it would need a pretty big parents array and result in big gate
> numbers in devicetree, <&bus_gates 112> for uart0 for example.
> 
> Would this be ok?

I don't see anything wrong with that, as long as we have a clear
documentation stating where that number comes from.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150512/3a10832f/attachment.sig>

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 7262 bytes --]

Hi,

On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
> On 09/05/15 13:27, Maxime Ripard wrote:
> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> >> The H3 clock control unit is similar to the those of other sun8i family
> >> members like the A23.
> >>
> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> >> The documentation isn't totally clear about which devices belong to
> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> >> kernel source code.
> >>
> >> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> >> ---
> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
> >>  2 files changed, 52 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> index 4fa11af..4eeb893 100644
> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> @@ -14,6 +14,8 @@ Required properties:
> >>  	"allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
> >>  	"allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
> >>  	"allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> >> +	"allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> >> +	"allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
> >>  	"allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
> >>  	"allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
> >>  	"allwinner,sun4i-a10-axi-clk" - for the AXI clock
> >> @@ -28,8 +30,11 @@ Required properties:
> >>  	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
> >>  	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> >>  	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> >> +	"allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> >>  	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> >>  	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> >> +	"allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> >> +	"allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
> >>  	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> >>  	"allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
> >>  	"allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> >> @@ -52,8 +57,10 @@ Required properties:
> >>  	"allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
> >>  	"allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
> >>  	"allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> >> +	"allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
> >>  	"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> >>  	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> >> +	"allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
> >>  	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> >>  	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> >>  	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> >> index 7e1e2bd..152a1f7 100644
> >> --- a/drivers/clk/sunxi/clk-sunxi.c
> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
> >>  	.getter = sun5i_a13_get_ahb_factors,
> >>  };
> >>  
> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> >> +	.enable = 31,
> >> +	.table = &sun6i_a31_pll6_config,
> >> +	.getter = sun6i_a31_get_pll6_factors,
> >> +};
> > 
> > This looks like it's just another instance of the A31 pll6.
> > 
> > In such a case, we don't need to declare a new driver, just reuse the
> > same compatible.
> 
> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
> field, already existing clock or something like that.

Damn. You're obviously right...

Could you add a TODO comment on top then? just so that we know that we
need to merge this clock with pll6?

> (And pll8 doesn't even have a x2 version)

Judging by the H3 datasheet, it does.

> >>  static const struct factors_data sun4i_apb1_data __initconst = {
> >>  	.mux = 24,
> >>  	.muxmask = BIT(1) | BIT(0),
> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> >>  	.shift = 12,
> >>  };
> >>  
> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> >> +	.shift = 0,
> >> +};
> >> +
> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
> >>  				       struct mux_data *data)
> >>  {
> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
> >>   */
> >>  
> >> -#define SUNXI_GATES_MAX_SIZE	64
> >> +#define SUNXI_GATES_MAX_SIZE	160
> >>  
> >>  struct gates_data {
> >>  	DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
> >>  	.mask = {0x25386742, 0x2505111},
> >>  };
> >>  
> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> >> +	.mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> >> +};
> >> +
> > 
> > Judging from the user manual, there's a few gates in those 0
> > registers, is this normal that you don't support them?
> 
> They are holes for apb1 and apb2. Which is actually pretty ugly.

Ah, right.

So I guess it's completely related to the discussion below.

> >>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
> >>  	.mask = {0xF5F12B},
> >>  };
> >> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
> >>  	.mask = {0x9B7},
> >>  };
> >>  
> >> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
> >> +	.mask = {0xe0020000},
> >> +};
> >> +
> > 
> > I don't think we should split the ahb1 and ahb2 gates here. It really
> > looks like it's the same controller.
> > 
> > The way I'm seeing it would be to have a single clock driver that
> > would handle both your ahb1 and ahb2 gates.
> > 
> > It would take two parents, ahb1 and ahb2, obviously, and would take
> > register depending on the gate w'ere registering either the ahb1 or
> > the ahb2 parent.
> > 
> > It seems like there's only a handful of devices in ahb2 anyway, so
> > that wouldn't make a very long list of devices to declare as childs of
> > ahb2.
> > 
> 
> I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
> and apb2 gates, as it is done in the user manual.
> 
> But it would need a pretty big parents array and result in big gate
> numbers in devicetree, <&bus_gates 112> for uart0 for example.
> 
> Would this be ok?

I don't see anything wrong with that, as long as we have a clear
documentation stating where that number comes from.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Chen-Yu Tsai]

On Tue, May 12, 2015 at 10:44 PM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> Hi,
>
> On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
>> On 09/05/15 13:27, Maxime Ripard wrote:
>> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
>> >> The H3 clock control unit is similar to the those of other sun8i family
>> >> members like the A23.
>> >>
>> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> >> The documentation isn't totally clear about which devices belong to
>> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> >> kernel source code.
>> >>
>> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> >> ---
>> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>> >>  2 files changed, 52 insertions(+), 1 deletion(-)
>> >>
>> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> index 4fa11af..4eeb893 100644
>> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> @@ -14,6 +14,8 @@ Required properties:
>> >>    "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>> >>    "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>> >>    "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> >> +  "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> >> +  "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>> >>    "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>> >>    "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>> >>    "allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> >> @@ -28,8 +30,11 @@ Required properties:
>> >>    "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>> >>    "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>> >>    "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> >> +  "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>> >>    "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>> >>    "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> >> +  "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> >> +  "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>> >>    "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>> >>    "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>> >>    "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> >> @@ -52,8 +57,10 @@ Required properties:
>> >>    "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>> >>    "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>> >>    "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> >> +  "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>> >>    "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>> >>    "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> >> +  "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>> >>    "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>> >>    "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>> >>    "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> >> index 7e1e2bd..152a1f7 100644
>> >> --- a/drivers/clk/sunxi/clk-sunxi.c
>> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>> >>    .getter = sun5i_a13_get_ahb_factors,
>> >>  };
>> >>
>> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> >> +  .enable = 31,
>> >> +  .table = &sun6i_a31_pll6_config,
>> >> +  .getter = sun6i_a31_get_pll6_factors,
>> >> +};
>> >
>> > This looks like it's just another instance of the A31 pll6.
>> >
>> > In such a case, we don't need to declare a new driver, just reuse the
>> > same compatible.
>>
>> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
>> field, already existing clock or something like that.
>
> Damn. You're obviously right...

I think I have a solution for this.

The current divs clock setup just passes the factors_data directly to
sunxi_factors_register(). What if it did a copy, read the _correct_
name from the DT (since it knows the index) and put it in the copy.

How does that sound?

> Could you add a TODO comment on top then? just so that we know that we
> need to merge this clock with pll6?
>
>> (And pll8 doesn't even have a x2 version)
>
> Judging by the H3 datasheet, it does.
>
>> >>  static const struct factors_data sun4i_apb1_data __initconst = {
>> >>    .mux = 24,
>> >>    .muxmask = BIT(1) | BIT(0),
>> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>> >>    .shift = 12,
>> >>  };
>> >>
>> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> >> +  .shift = 0,
>> >> +};
>> >> +
>> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>> >>                                   struct mux_data *data)
>> >>  {
>> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>> >>   */
>> >>
>> >> -#define SUNXI_GATES_MAX_SIZE      64
>> >> +#define SUNXI_GATES_MAX_SIZE      160
>> >>
>> >>  struct gates_data {
>> >>    DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>> >>    .mask = {0x25386742, 0x2505111},
>> >>  };
>> >>
>> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> >> +  .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> >> +};
>> >> +
>> >
>> > Judging from the user manual, there's a few gates in those 0
>> > registers, is this normal that you don't support them?
>>
>> They are holes for apb1 and apb2. Which is actually pretty ugly.
>
> Ah, right.
>
> So I guess it's completely related to the discussion below.

If the holes are really big, I guess you could split ahb and apb?


ChenYu

>> >>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>> >>    .mask = {0xF5F12B},
>> >>  };
>> >> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>> >>    .mask = {0x9B7},
>> >>  };
>> >>
>> >> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> >> +  .mask = {0xe0020000},
>> >> +};
>> >> +
>> >
>> > I don't think we should split the ahb1 and ahb2 gates here. It really
>> > looks like it's the same controller.
>> >
>> > The way I'm seeing it would be to have a single clock driver that
>> > would handle both your ahb1 and ahb2 gates.
>> >
>> > It would take two parents, ahb1 and ahb2, obviously, and would take
>> > register depending on the gate w'ere registering either the ahb1 or
>> > the ahb2 parent.
>> >
>> > It seems like there's only a handful of devices in ahb2 anyway, so
>> > that wouldn't make a very long list of devices to declare as childs of
>> > ahb2.
>> >
>>
>> I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
>> and apb2 gates, as it is done in the user manual.
>>
>> But it would need a pretty big parents array and result in big gate
>> numbers in devicetree, <&bus_gates 112> for uart0 for example.
>>
>> Would this be ok?
>
> I don't see anything wrong with that, as long as we have a clear
> documentation stating where that number comes from.
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Chen-Yu Tsai]

On Tue, May 12, 2015 at 10:44 PM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> Hi,
>
> On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
>> On 09/05/15 13:27, Maxime Ripard wrote:
>> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
>> >> The H3 clock control unit is similar to the those of other sun8i family
>> >> members like the A23.
>> >>
>> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> >> The documentation isn't totally clear about which devices belong to
>> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> >> kernel source code.
>> >>
>> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> >> ---
>> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>> >>  2 files changed, 52 insertions(+), 1 deletion(-)
>> >>
>> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> index 4fa11af..4eeb893 100644
>> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> @@ -14,6 +14,8 @@ Required properties:
>> >>    "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>> >>    "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>> >>    "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> >> +  "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> >> +  "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>> >>    "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>> >>    "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>> >>    "allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> >> @@ -28,8 +30,11 @@ Required properties:
>> >>    "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>> >>    "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>> >>    "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> >> +  "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>> >>    "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>> >>    "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> >> +  "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> >> +  "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>> >>    "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>> >>    "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>> >>    "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> >> @@ -52,8 +57,10 @@ Required properties:
>> >>    "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>> >>    "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>> >>    "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> >> +  "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>> >>    "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>> >>    "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> >> +  "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>> >>    "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>> >>    "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>> >>    "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> >> index 7e1e2bd..152a1f7 100644
>> >> --- a/drivers/clk/sunxi/clk-sunxi.c
>> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>> >>    .getter = sun5i_a13_get_ahb_factors,
>> >>  };
>> >>
>> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> >> +  .enable = 31,
>> >> +  .table = &sun6i_a31_pll6_config,
>> >> +  .getter = sun6i_a31_get_pll6_factors,
>> >> +};
>> >
>> > This looks like it's just another instance of the A31 pll6.
>> >
>> > In such a case, we don't need to declare a new driver, just reuse the
>> > same compatible.
>>
>> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
>> field, already existing clock or something like that.
>
> Damn. You're obviously right...

I think I have a solution for this.

The current divs clock setup just passes the factors_data directly to
sunxi_factors_register(). What if it did a copy, read the _correct_
name from the DT (since it knows the index) and put it in the copy.

How does that sound?

> Could you add a TODO comment on top then? just so that we know that we
> need to merge this clock with pll6?
>
>> (And pll8 doesn't even have a x2 version)
>
> Judging by the H3 datasheet, it does.
>
>> >>  static const struct factors_data sun4i_apb1_data __initconst = {
>> >>    .mux = 24,
>> >>    .muxmask = BIT(1) | BIT(0),
>> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>> >>    .shift = 12,
>> >>  };
>> >>
>> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> >> +  .shift = 0,
>> >> +};
>> >> +
>> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>> >>                                   struct mux_data *data)
>> >>  {
>> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>> >>   */
>> >>
>> >> -#define SUNXI_GATES_MAX_SIZE      64
>> >> +#define SUNXI_GATES_MAX_SIZE      160
>> >>
>> >>  struct gates_data {
>> >>    DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>> >>    .mask = {0x25386742, 0x2505111},
>> >>  };
>> >>
>> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> >> +  .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> >> +};
>> >> +
>> >
>> > Judging from the user manual, there's a few gates in those 0
>> > registers, is this normal that you don't support them?
>>
>> They are holes for apb1 and apb2. Which is actually pretty ugly.
>
> Ah, right.
>
> So I guess it's completely related to the discussion below.

If the holes are really big, I guess you could split ahb and apb?


ChenYu

>> >>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>> >>    .mask = {0xF5F12B},
>> >>  };
>> >> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>> >>    .mask = {0x9B7},
>> >>  };
>> >>
>> >> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> >> +  .mask = {0xe0020000},
>> >> +};
>> >> +
>> >
>> > I don't think we should split the ahb1 and ahb2 gates here. It really
>> > looks like it's the same controller.
>> >
>> > The way I'm seeing it would be to have a single clock driver that
>> > would handle both your ahb1 and ahb2 gates.
>> >
>> > It would take two parents, ahb1 and ahb2, obviously, and would take
>> > register depending on the gate w'ere registering either the ahb1 or
>> > the ahb2 parent.
>> >
>> > It seems like there's only a handful of devices in ahb2 anyway, so
>> > that wouldn't make a very long list of devices to declare as childs of
>> > ahb2.
>> >
>>
>> I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
>> and apb2 gates, as it is done in the user manual.
>>
>> But it would need a pretty big parents array and result in big gate
>> numbers in devicetree, <&bus_gates 112> for uart0 for example.
>>
>> Would this be ok?
>
> I don't see anything wrong with that, as long as we have a clear
> documentation stating where that number comes from.
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Chen-Yu Tsai]

On Tue, May 12, 2015 at 10:44 PM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi,
>
> On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
>> On 09/05/15 13:27, Maxime Ripard wrote:
>> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
>> >> The H3 clock control unit is similar to the those of other sun8i family
>> >> members like the A23.
>> >>
>> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
>> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
>> >> The documentation isn't totally clear about which devices belong to
>> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
>> >> kernel source code.
>> >>
>> >> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> >> ---
>> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
>> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
>> >>  2 files changed, 52 insertions(+), 1 deletion(-)
>> >>
>> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> index 4fa11af..4eeb893 100644
>> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> >> @@ -14,6 +14,8 @@ Required properties:
>> >>    "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
>> >>    "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
>> >>    "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
>> >> +  "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
>> >> +  "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
>> >>    "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
>> >>    "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
>> >>    "allwinner,sun4i-a10-axi-clk" - for the AXI clock
>> >> @@ -28,8 +30,11 @@ Required properties:
>> >>    "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
>> >>    "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
>> >>    "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
>> >> +  "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
>> >>    "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
>> >>    "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
>> >> +  "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
>> >> +  "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
>> >>    "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
>> >>    "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
>> >>    "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
>> >> @@ -52,8 +57,10 @@ Required properties:
>> >>    "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
>> >>    "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
>> >>    "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
>> >> +  "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
>> >>    "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
>> >>    "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> >> +  "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
>> >>    "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
>> >>    "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
>> >>    "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
>> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> >> index 7e1e2bd..152a1f7 100644
>> >> --- a/drivers/clk/sunxi/clk-sunxi.c
>> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
>> >>    .getter = sun5i_a13_get_ahb_factors,
>> >>  };
>> >>
>> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
>> >> +  .enable = 31,
>> >> +  .table = &sun6i_a31_pll6_config,
>> >> +  .getter = sun6i_a31_get_pll6_factors,
>> >> +};
>> >
>> > This looks like it's just another instance of the A31 pll6.
>> >
>> > In such a case, we don't need to declare a new driver, just reuse the
>> > same compatible.
>>
>> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
>> field, already existing clock or something like that.
>
> Damn. You're obviously right...

I think I have a solution for this.

The current divs clock setup just passes the factors_data directly to
sunxi_factors_register(). What if it did a copy, read the _correct_
name from the DT (since it knows the index) and put it in the copy.

How does that sound?

> Could you add a TODO comment on top then? just so that we know that we
> need to merge this clock with pll6?
>
>> (And pll8 doesn't even have a x2 version)
>
> Judging by the H3 datasheet, it does.
>
>> >>  static const struct factors_data sun4i_apb1_data __initconst = {
>> >>    .mux = 24,
>> >>    .muxmask = BIT(1) | BIT(0),
>> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
>> >>    .shift = 12,
>> >>  };
>> >>
>> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
>> >> +  .shift = 0,
>> >> +};
>> >> +
>> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
>> >>                                   struct mux_data *data)
>> >>  {
>> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
>> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
>> >>   */
>> >>
>> >> -#define SUNXI_GATES_MAX_SIZE      64
>> >> +#define SUNXI_GATES_MAX_SIZE      160
>> >>
>> >>  struct gates_data {
>> >>    DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
>> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
>> >>    .mask = {0x25386742, 0x2505111},
>> >>  };
>> >>
>> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
>> >> +  .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
>> >> +};
>> >> +
>> >
>> > Judging from the user manual, there's a few gates in those 0
>> > registers, is this normal that you don't support them?
>>
>> They are holes for apb1 and apb2. Which is actually pretty ugly.
>
> Ah, right.
>
> So I guess it's completely related to the discussion below.

If the holes are really big, I guess you could split ahb and apb?


ChenYu

>> >>  static const struct gates_data sun9i_a80_ahb0_gates_data __initconst = {
>> >>    .mask = {0xF5F12B},
>> >>  };
>> >> @@ -938,6 +952,10 @@ static const struct gates_data sun9i_a80_ahb2_gates_data __initconst = {
>> >>    .mask = {0x9B7},
>> >>  };
>> >>
>> >> +static const struct gates_data sun8i_h3_ahb2_gates_data __initconst = {
>> >> +  .mask = {0xe0020000},
>> >> +};
>> >> +
>> >
>> > I don't think we should split the ahb1 and ahb2 gates here. It really
>> > looks like it's the same controller.
>> >
>> > The way I'm seeing it would be to have a single clock driver that
>> > would handle both your ahb1 and ahb2 gates.
>> >
>> > It would take two parents, ahb1 and ahb2, obviously, and would take
>> > register depending on the gate w'ere registering either the ahb1 or
>> > the ahb2 parent.
>> >
>> > It seems like there's only a handful of devices in ahb2 anyway, so
>> > that wouldn't make a very long list of devices to declare as childs of
>> > ahb2.
>> >
>>
>> I have thought about adding a bus_gates driver for all ahb1, ahb2, apb1
>> and apb2 gates, as it is done in the user manual.
>>
>> But it would need a pretty big parents array and result in big gate
>> numbers in devicetree, <&bus_gates 112> for uart0 for example.
>>
>> Would this be ok?
>
> I don't see anything wrong with that, as long as we have a clear
> documentation stating where that number comes from.
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 7186 bytes --]

On Thu, May 14, 2015 at 01:14:25PM +0800, Chen-Yu Tsai wrote:
> On Tue, May 12, 2015 at 10:44 PM, Maxime Ripard
> <maxime.ripard@free-electrons.com> wrote:
> > Hi,
> >
> > On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
> >> On 09/05/15 13:27, Maxime Ripard wrote:
> >> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> >> >> The H3 clock control unit is similar to the those of other sun8i family
> >> >> members like the A23.
> >> >>
> >> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> >> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> >> >> The documentation isn't totally clear about which devices belong to
> >> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> >> >> kernel source code.
> >> >>
> >> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> >> >> ---
> >> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
> >> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
> >> >>  2 files changed, 52 insertions(+), 1 deletion(-)
> >> >>
> >> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> index 4fa11af..4eeb893 100644
> >> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> @@ -14,6 +14,8 @@ Required properties:
> >> >>    "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
> >> >>    "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
> >> >>    "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> >> >> +  "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> >> >> +  "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
> >> >>    "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
> >> >>    "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
> >> >>    "allwinner,sun4i-a10-axi-clk" - for the AXI clock
> >> >> @@ -28,8 +30,11 @@ Required properties:
> >> >>    "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
> >> >>    "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> >> >>    "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> >> >> +  "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> >> >>    "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> >> >>    "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> >> >> +  "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> >> >> +  "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
> >> >>    "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> >> >>    "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
> >> >>    "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> >> >> @@ -52,8 +57,10 @@ Required properties:
> >> >>    "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
> >> >>    "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
> >> >>    "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> >> >> +  "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
> >> >>    "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> >> >>    "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> >> >> +  "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
> >> >>    "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> >> >>    "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> >> >>    "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> >> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> >> >> index 7e1e2bd..152a1f7 100644
> >> >> --- a/drivers/clk/sunxi/clk-sunxi.c
> >> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
> >> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
> >> >>    .getter = sun5i_a13_get_ahb_factors,
> >> >>  };
> >> >>
> >> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> >> >> +  .enable = 31,
> >> >> +  .table = &sun6i_a31_pll6_config,
> >> >> +  .getter = sun6i_a31_get_pll6_factors,
> >> >> +};
> >> >
> >> > This looks like it's just another instance of the A31 pll6.
> >> >
> >> > In such a case, we don't need to declare a new driver, just reuse the
> >> > same compatible.
> >>
> >> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
> >> field, already existing clock or something like that.
> >
> > Damn. You're obviously right...
> 
> I think I have a solution for this.
> 
> The current divs clock setup just passes the factors_data directly to
> sunxi_factors_register(). What if it did a copy, read the _correct_
> name from the DT (since it knows the index) and put it in the copy.
> 
> How does that sound?

That sounds great, but what name would you take from the DT? The first
of clock-output-names? the last one? a random one?

> 
> > Could you add a TODO comment on top then? just so that we know that we
> > need to merge this clock with pll6?
> >
> >> (And pll8 doesn't even have a x2 version)
> >
> > Judging by the H3 datasheet, it does.
> >
> >> >>  static const struct factors_data sun4i_apb1_data __initconst = {
> >> >>    .mux = 24,
> >> >>    .muxmask = BIT(1) | BIT(0),
> >> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> >> >>    .shift = 12,
> >> >>  };
> >> >>
> >> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> >> >> +  .shift = 0,
> >> >> +};
> >> >> +
> >> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
> >> >>                                   struct mux_data *data)
> >> >>  {
> >> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
> >> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
> >> >>   */
> >> >>
> >> >> -#define SUNXI_GATES_MAX_SIZE      64
> >> >> +#define SUNXI_GATES_MAX_SIZE      160
> >> >>
> >> >>  struct gates_data {
> >> >>    DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> >> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
> >> >>    .mask = {0x25386742, 0x2505111},
> >> >>  };
> >> >>
> >> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> >> >> +  .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> >> >> +};
> >> >> +
> >> >
> >> > Judging from the user manual, there's a few gates in those 0
> >> > registers, is this normal that you don't support them?
> >>
> >> They are holes for apb1 and apb2. Which is actually pretty ugly.
> >
> > Ah, right.
> >
> > So I guess it's completely related to the discussion below.
> 
> If the holes are really big, I guess you could split ahb and apb?

It's actually already split. The holes in the ahb1 registers are for
the apb clocks.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

On Thu, May 14, 2015 at 01:14:25PM +0800, Chen-Yu Tsai wrote:
> On Tue, May 12, 2015 at 10:44 PM, Maxime Ripard
> <maxime.ripard@free-electrons.com> wrote:
> > Hi,
> >
> > On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
> >> On 09/05/15 13:27, Maxime Ripard wrote:
> >> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> >> >> The H3 clock control unit is similar to the those of other sun8i family
> >> >> members like the A23.
> >> >>
> >> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> >> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> >> >> The documentation isn't totally clear about which devices belong to
> >> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> >> >> kernel source code.
> >> >>
> >> >> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> >> >> ---
> >> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
> >> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
> >> >>  2 files changed, 52 insertions(+), 1 deletion(-)
> >> >>
> >> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> index 4fa11af..4eeb893 100644
> >> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> @@ -14,6 +14,8 @@ Required properties:
> >> >>    "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
> >> >>    "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
> >> >>    "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> >> >> +  "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> >> >> +  "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
> >> >>    "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
> >> >>    "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
> >> >>    "allwinner,sun4i-a10-axi-clk" - for the AXI clock
> >> >> @@ -28,8 +30,11 @@ Required properties:
> >> >>    "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
> >> >>    "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> >> >>    "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> >> >> +  "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> >> >>    "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> >> >>    "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> >> >> +  "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> >> >> +  "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
> >> >>    "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> >> >>    "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
> >> >>    "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> >> >> @@ -52,8 +57,10 @@ Required properties:
> >> >>    "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
> >> >>    "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
> >> >>    "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> >> >> +  "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
> >> >>    "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> >> >>    "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> >> >> +  "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
> >> >>    "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> >> >>    "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> >> >>    "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> >> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> >> >> index 7e1e2bd..152a1f7 100644
> >> >> --- a/drivers/clk/sunxi/clk-sunxi.c
> >> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
> >> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
> >> >>    .getter = sun5i_a13_get_ahb_factors,
> >> >>  };
> >> >>
> >> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> >> >> +  .enable = 31,
> >> >> +  .table = &sun6i_a31_pll6_config,
> >> >> +  .getter = sun6i_a31_get_pll6_factors,
> >> >> +};
> >> >
> >> > This looks like it's just another instance of the A31 pll6.
> >> >
> >> > In such a case, we don't need to declare a new driver, just reuse the
> >> > same compatible.
> >>
> >> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
> >> field, already existing clock or something like that.
> >
> > Damn. You're obviously right...
> 
> I think I have a solution for this.
> 
> The current divs clock setup just passes the factors_data directly to
> sunxi_factors_register(). What if it did a copy, read the _correct_
> name from the DT (since it knows the index) and put it in the copy.
> 
> How does that sound?

That sounds great, but what name would you take from the DT? The first
of clock-output-names? the last one? a random one?

> 
> > Could you add a TODO comment on top then? just so that we know that we
> > need to merge this clock with pll6?
> >
> >> (And pll8 doesn't even have a x2 version)
> >
> > Judging by the H3 datasheet, it does.
> >
> >> >>  static const struct factors_data sun4i_apb1_data __initconst = {
> >> >>    .mux = 24,
> >> >>    .muxmask = BIT(1) | BIT(0),
> >> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> >> >>    .shift = 12,
> >> >>  };
> >> >>
> >> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> >> >> +  .shift = 0,
> >> >> +};
> >> >> +
> >> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
> >> >>                                   struct mux_data *data)
> >> >>  {
> >> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
> >> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
> >> >>   */
> >> >>
> >> >> -#define SUNXI_GATES_MAX_SIZE      64
> >> >> +#define SUNXI_GATES_MAX_SIZE      160
> >> >>
> >> >>  struct gates_data {
> >> >>    DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> >> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
> >> >>    .mask = {0x25386742, 0x2505111},
> >> >>  };
> >> >>
> >> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> >> >> +  .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> >> >> +};
> >> >> +
> >> >
> >> > Judging from the user manual, there's a few gates in those 0
> >> > registers, is this normal that you don't support them?
> >>
> >> They are holes for apb1 and apb2. Which is actually pretty ugly.
> >
> > Ah, right.
> >
> > So I guess it's completely related to the discussion below.
> 
> If the holes are really big, I guess you could split ahb and apb?

It's actually already split. The holes in the ahb1 registers are for
the apb clocks.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150515/f6fae41b/attachment.sig>

Re: [PATCH 2/6] clk: sunxi: Add H3 clocks support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 7092 bytes --]

On Thu, May 14, 2015 at 01:14:25PM +0800, Chen-Yu Tsai wrote:
> On Tue, May 12, 2015 at 10:44 PM, Maxime Ripard
> <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> > Hi,
> >
> > On Sun, May 10, 2015 at 12:54:50PM +0200, Jens Kuske wrote:
> >> On 09/05/15 13:27, Maxime Ripard wrote:
> >> > On Wed, May 06, 2015 at 11:31:29AM +0200, Jens Kuske wrote:
> >> >> The H3 clock control unit is similar to the those of other sun8i family
> >> >> members like the A23.
> >> >>
> >> >> The AHB1 gates got split up into AHB1 and AHB2, with AHB2 clock source
> >> >> being muxable between AHB1 and PLL6/2, but still sharing gate registers.
> >> >> The documentation isn't totally clear about which devices belong to
> >> >> AHB2 now, especially USB EHIC/OHIC, so it is mostly based on Allwinner
> >> >> kernel source code.
> >> >>
> >> >> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> >> >> ---
> >> >>  Documentation/devicetree/bindings/clock/sunxi.txt |  7 ++++
> >> >>  drivers/clk/sunxi/clk-sunxi.c                     | 46 ++++++++++++++++++++++-
> >> >>  2 files changed, 52 insertions(+), 1 deletion(-)
> >> >>
> >> >> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> index 4fa11af..4eeb893 100644
> >> >> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> >> >> @@ -14,6 +14,8 @@ Required properties:
> >> >>    "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock
> >> >>    "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock
> >> >>    "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31
> >> >> +  "allwinner,sun8i-h3-pll6-clk" - for the PLL6 clock on H3
> >> >> +  "allwinner,sun8i-h3-pll8-clk" - for the PLL8 clock on H3
> >> >>    "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80
> >> >>    "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock
> >> >>    "allwinner,sun4i-a10-axi-clk" - for the AXI clock
> >> >> @@ -28,8 +30,11 @@ Required properties:
> >> >>    "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
> >> >>    "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> >> >>    "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> >> >> +  "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> >> >>    "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> >> >>    "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> >> >> +  "allwinner,sun8i-h3-ahb1-gates-clk" - for the AHB1 gates on H3
> >> >> +  "allwinner,sun8i-h3-ahb2-gates-clk" - for the AHB2 gates on H3
> >> >>    "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> >> >>    "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80
> >> >>    "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80
> >> >> @@ -52,8 +57,10 @@ Required properties:
> >> >>    "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31
> >> >>    "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20
> >> >>    "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23
> >> >> +  "allwinner,sun8i-h3-apb1-gates-clk" - for the APB1 gates on H3
> >> >>    "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> >> >>    "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> >> >> +  "allwinner,sun8i-h3-apb2-gates-clk" - for the APB2 gates on H3
> >> >>    "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> >> >>    "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> >> >>    "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> >> >> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> >> >> index 7e1e2bd..152a1f7 100644
> >> >> --- a/drivers/clk/sunxi/clk-sunxi.c
> >> >> +++ b/drivers/clk/sunxi/clk-sunxi.c
> >> >> @@ -727,6 +727,12 @@ static const struct factors_data sun5i_a13_ahb_data __initconst = {
> >> >>    .getter = sun5i_a13_get_ahb_factors,
> >> >>  };
> >> >>
> >> >> +static const struct factors_data sun8i_h3_pll8_data __initconst = {
> >> >> +  .enable = 31,
> >> >> +  .table = &sun6i_a31_pll6_config,
> >> >> +  .getter = sun6i_a31_get_pll6_factors,
> >> >> +};
> >> >
> >> > This looks like it's just another instance of the A31 pll6.
> >> >
> >> > In such a case, we don't need to declare a new driver, just reuse the
> >> > same compatible.
> >>
> >> If I reuse pll6 for pll8 I get errors because of the .name = "pll6x2"
> >> field, already existing clock or something like that.
> >
> > Damn. You're obviously right...
> 
> I think I have a solution for this.
> 
> The current divs clock setup just passes the factors_data directly to
> sunxi_factors_register(). What if it did a copy, read the _correct_
> name from the DT (since it knows the index) and put it in the copy.
> 
> How does that sound?

That sounds great, but what name would you take from the DT? The first
of clock-output-names? the last one? a random one?

> 
> > Could you add a TODO comment on top then? just so that we know that we
> > need to merge this clock with pll6?
> >
> >> (And pll8 doesn't even have a x2 version)
> >
> > Judging by the H3 datasheet, it does.
> >
> >> >>  static const struct factors_data sun4i_apb1_data __initconst = {
> >> >>    .mux = 24,
> >> >>    .muxmask = BIT(1) | BIT(0),
> >> >> @@ -777,6 +783,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> >> >>    .shift = 12,
> >> >>  };
> >> >>
> >> >> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> >> >> +  .shift = 0,
> >> >> +};
> >> >> +
> >> >>  static void __init sunxi_mux_clk_setup(struct device_node *node,
> >> >>                                   struct mux_data *data)
> >> >>  {
> >> >> @@ -892,7 +902,7 @@ static void __init sunxi_divider_clk_setup(struct device_node *node,
> >> >>   * sunxi_gates_clk_setup() - Setup function for leaf gates on clocks
> >> >>   */
> >> >>
> >> >> -#define SUNXI_GATES_MAX_SIZE      64
> >> >> +#define SUNXI_GATES_MAX_SIZE      160
> >> >>
> >> >>  struct gates_data {
> >> >>    DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> >> >> @@ -926,6 +936,10 @@ static const struct gates_data sun8i_a23_ahb1_gates_data __initconst = {
> >> >>    .mask = {0x25386742, 0x2505111},
> >> >>  };
> >> >>
> >> >> +static const struct gates_data sun8i_h3_ahb1_gates_data __initconst = {
> >> >> +  .mask = {0x1fbc6760, 0x00701b39, 0x00000000, 0x00000000, 0x00000081},
> >> >> +};
> >> >> +
> >> >
> >> > Judging from the user manual, there's a few gates in those 0
> >> > registers, is this normal that you don't support them?
> >>
> >> They are holes for apb1 and apb2. Which is actually pretty ugly.
> >
> > Ah, right.
> >
> > So I guess it's completely related to the discussion below.
> 
> If the holes are really big, I guess you could split ahb and apb?

It's actually already split. The holes in the ahb1 registers are for
the apb clocks.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
 4 files changed, 527 insertions(+)
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index fdd8046..c46af8e 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -16,6 +16,7 @@ Required properties:
   "allwinner,sun7i-a20-pinctrl"
   "allwinner,sun8i-a23-pinctrl"
   "allwinner,sun8i-a23-r-pinctrl"
+  "allwinner,sun8i-h3-pinctrl"
 - reg: Should contain the register physical address and length for the
   pin controller.
 
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 2eb893e..c49e762 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
 	def_bool MACH_SUN8I
 	select PINCTRL_SUNXI_COMMON
 
+config PINCTRL_SUN8I_H3
+	def_bool MACH_SUN8I
+	select PINCTRL_SUNXI_COMMON
+
 config PINCTRL_SUN8I_A23_R
 	def_bool MACH_SUN8I
 	depends on RESET_CONTROLLER
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index b796d57..fd4a068 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
 obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
+obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
 obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
new file mode 100644
index 0000000..e20f511
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
@@ -0,0 +1,521 @@
+/*
+ * Allwinner H3 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun8i_h3_pins[] = {
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "pwm0"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
+		  SUNXI_FUNCTION(0x3, "pwm1"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
+		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
+		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
+		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
+		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
+		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
+	.pins = sun8i_h3_pins,
+	.npins = ARRAY_SIZE(sun8i_h3_pins),
+	.irq_banks = 2,
+};
+
+static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
+{
+	return sunxi_pinctrl_init(pdev,
+				  &sun8i_h3_pinctrl_data);
+}
+
+static const struct of_device_id sun8i_h3_pinctrl_match[] = {
+	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
+
+static struct platform_driver sun8i_h3_pinctrl_driver = {
+	.probe	= sun8i_h3_pinctrl_probe,
+	.driver	= {
+		.name		= "sun8i-h3-pinctrl",
+		.of_match_table	= sun8i_h3_pinctrl_match,
+	},
+};
+module_platform_driver(sun8i_h3_pinctrl_driver);
+
+MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
+MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
+MODULE_LICENSE("GPL");
-- 
2.3.7

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
 4 files changed, 527 insertions(+)
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index fdd8046..c46af8e 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -16,6 +16,7 @@ Required properties:
   "allwinner,sun7i-a20-pinctrl"
   "allwinner,sun8i-a23-pinctrl"
   "allwinner,sun8i-a23-r-pinctrl"
+  "allwinner,sun8i-h3-pinctrl"
 - reg: Should contain the register physical address and length for the
   pin controller.
 
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 2eb893e..c49e762 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
 	def_bool MACH_SUN8I
 	select PINCTRL_SUNXI_COMMON
 
+config PINCTRL_SUN8I_H3
+	def_bool MACH_SUN8I
+	select PINCTRL_SUNXI_COMMON
+
 config PINCTRL_SUN8I_A23_R
 	def_bool MACH_SUN8I
 	depends on RESET_CONTROLLER
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index b796d57..fd4a068 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
 obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
+obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
 obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
new file mode 100644
index 0000000..e20f511
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
@@ -0,0 +1,521 @@
+/*
+ * Allwinner H3 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun8i_h3_pins[] = {
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "pwm0"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
+		  SUNXI_FUNCTION(0x3, "pwm1"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
+		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
+		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
+		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
+		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
+		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
+	.pins = sun8i_h3_pins,
+	.npins = ARRAY_SIZE(sun8i_h3_pins),
+	.irq_banks = 2,
+};
+
+static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
+{
+	return sunxi_pinctrl_init(pdev,
+				  &sun8i_h3_pinctrl_data);
+}
+
+static const struct of_device_id sun8i_h3_pinctrl_match[] = {
+	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
+
+static struct platform_driver sun8i_h3_pinctrl_driver = {
+	.probe	= sun8i_h3_pinctrl_probe,
+	.driver	= {
+		.name		= "sun8i-h3-pinctrl",
+		.of_match_table	= sun8i_h3_pinctrl_match,
+	},
+};
+module_platform_driver(sun8i_h3_pinctrl_driver);
+
+MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
+MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
+MODULE_LICENSE("GPL");
-- 
2.3.7

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.

Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
 4 files changed, 527 insertions(+)
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index fdd8046..c46af8e 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -16,6 +16,7 @@ Required properties:
   "allwinner,sun7i-a20-pinctrl"
   "allwinner,sun8i-a23-pinctrl"
   "allwinner,sun8i-a23-r-pinctrl"
+  "allwinner,sun8i-h3-pinctrl"
 - reg: Should contain the register physical address and length for the
   pin controller.
 
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 2eb893e..c49e762 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
 	def_bool MACH_SUN8I
 	select PINCTRL_SUNXI_COMMON
 
+config PINCTRL_SUN8I_H3
+	def_bool MACH_SUN8I
+	select PINCTRL_SUNXI_COMMON
+
 config PINCTRL_SUN8I_A23_R
 	def_bool MACH_SUN8I
 	depends on RESET_CONTROLLER
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index b796d57..fd4a068 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
 obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
+obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
 obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
new file mode 100644
index 0000000..e20f511
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
@@ -0,0 +1,521 @@
+/*
+ * Allwinner H3 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun8i_h3_pins[] = {
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
+		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
+		  SUNXI_FUNCTION(0x3, "pwm0"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
+		  SUNXI_FUNCTION(0x3, "pwm1"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
+		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
+		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
+		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
+		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
+		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
+		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
+		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
+	.pins = sun8i_h3_pins,
+	.npins = ARRAY_SIZE(sun8i_h3_pins),
+	.irq_banks = 2,
+};
+
+static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
+{
+	return sunxi_pinctrl_init(pdev,
+				  &sun8i_h3_pinctrl_data);
+}
+
+static const struct of_device_id sun8i_h3_pinctrl_match[] = {
+	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
+
+static struct platform_driver sun8i_h3_pinctrl_driver = {
+	.probe	= sun8i_h3_pinctrl_probe,
+	.driver	= {
+		.name		= "sun8i-h3-pinctrl",
+		.of_match_table	= sun8i_h3_pinctrl_match,
+	},
+};
+module_platform_driver(sun8i_h3_pinctrl_driver);
+
+MODULE_AUTHOR("Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>");
+MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
+MODULE_LICENSE("GPL");
-- 
2.3.7

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 25115 bytes --]

On Wed, May 06, 2015 at 11:31:30AM +0200, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>  drivers/pinctrl/sunxi/Kconfig                      |   4 +
>  drivers/pinctrl/sunxi/Makefile                     |   1 +
>  drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
>  4 files changed, 527 insertions(+)
>  create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> index fdd8046..c46af8e 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> @@ -16,6 +16,7 @@ Required properties:
>    "allwinner,sun7i-a20-pinctrl"
>    "allwinner,sun8i-a23-pinctrl"
>    "allwinner,sun8i-a23-r-pinctrl"
> +  "allwinner,sun8i-h3-pinctrl"
>  - reg: Should contain the register physical address and length for the
>    pin controller.
>  
> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
> index 2eb893e..c49e762 100644
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
> @@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
>  	def_bool MACH_SUN8I
>  	select PINCTRL_SUNXI_COMMON
>  
> +config PINCTRL_SUN8I_H3
> +	def_bool MACH_SUN8I
> +	select PINCTRL_SUNXI_COMMON
> +
>  config PINCTRL_SUN8I_A23_R
>  	def_bool MACH_SUN8I
>  	depends on RESET_CONTROLLER
> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
> index b796d57..fd4a068 100644
> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile
> @@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
>  obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
>  obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
>  obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
>  obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> new file mode 100644
> index 0000000..e20f511
> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> @@ -0,0 +1,521 @@
> +/*
> + * Allwinner H3 SoCs pinctrl driver.
> + *
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on pinctrl-sun8i-a23.c, which is:
> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2.  This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/pinctrl/pinctrl.h>
> +
> +#include "pinctrl-sunxi.h"
> +
> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
> +		  SUNXI_FUNCTION(0x3, "pwm0"),
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */

The datasheet uses "SIM" for this, why have you changed the name here?

> +		  SUNXI_FUNCTION(0x3, "pwm1"),
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
> +		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
> +		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
> +};
> +
> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
> +	.pins = sun8i_h3_pins,
> +	.npins = ARRAY_SIZE(sun8i_h3_pins),
> +	.irq_banks = 2,
> +};
> +
> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
> +{
> +	return sunxi_pinctrl_init(pdev,
> +				  &sun8i_h3_pinctrl_data);
> +}
> +
> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
> +	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> +
> +static struct platform_driver sun8i_h3_pinctrl_driver = {
> +	.probe	= sun8i_h3_pinctrl_probe,
> +	.driver	= {
> +		.name		= "sun8i-h3-pinctrl",
> +		.of_match_table	= sun8i_h3_pinctrl_match,
> +	},
> +};
> +module_platform_driver(sun8i_h3_pinctrl_driver);
> +
> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.3.7
> 

Looks good otherwise, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

On Wed, May 06, 2015 at 11:31:30AM +0200, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>  drivers/pinctrl/sunxi/Kconfig                      |   4 +
>  drivers/pinctrl/sunxi/Makefile                     |   1 +
>  drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
>  4 files changed, 527 insertions(+)
>  create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> index fdd8046..c46af8e 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> @@ -16,6 +16,7 @@ Required properties:
>    "allwinner,sun7i-a20-pinctrl"
>    "allwinner,sun8i-a23-pinctrl"
>    "allwinner,sun8i-a23-r-pinctrl"
> +  "allwinner,sun8i-h3-pinctrl"
>  - reg: Should contain the register physical address and length for the
>    pin controller.
>  
> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
> index 2eb893e..c49e762 100644
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
> @@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
>  	def_bool MACH_SUN8I
>  	select PINCTRL_SUNXI_COMMON
>  
> +config PINCTRL_SUN8I_H3
> +	def_bool MACH_SUN8I
> +	select PINCTRL_SUNXI_COMMON
> +
>  config PINCTRL_SUN8I_A23_R
>  	def_bool MACH_SUN8I
>  	depends on RESET_CONTROLLER
> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
> index b796d57..fd4a068 100644
> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile
> @@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
>  obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
>  obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
>  obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
>  obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> new file mode 100644
> index 0000000..e20f511
> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> @@ -0,0 +1,521 @@
> +/*
> + * Allwinner H3 SoCs pinctrl driver.
> + *
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on pinctrl-sun8i-a23.c, which is:
> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2.  This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/pinctrl/pinctrl.h>
> +
> +#include "pinctrl-sunxi.h"
> +
> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
> +		  SUNXI_FUNCTION(0x3, "pwm0"),
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */

The datasheet uses "SIM" for this, why have you changed the name here?

> +		  SUNXI_FUNCTION(0x3, "pwm1"),
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
> +		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
> +		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
> +	/* Hole */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
> +};
> +
> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
> +	.pins = sun8i_h3_pins,
> +	.npins = ARRAY_SIZE(sun8i_h3_pins),
> +	.irq_banks = 2,
> +};
> +
> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
> +{
> +	return sunxi_pinctrl_init(pdev,
> +				  &sun8i_h3_pinctrl_data);
> +}
> +
> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
> +	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> +
> +static struct platform_driver sun8i_h3_pinctrl_driver = {
> +	.probe	= sun8i_h3_pinctrl_probe,
> +	.driver	= {
> +		.name		= "sun8i-h3-pinctrl",
> +		.of_match_table	= sun8i_h3_pinctrl_match,
> +	},
> +};
> +module_platform_driver(sun8i_h3_pinctrl_driver);
> +
> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.3.7
> 

Looks good otherwise, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150506/78df9e71/attachment-0001.sig>

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

Hi,

On 06/05/15 12:11, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:30AM +0200, Jens Kuske wrote:
>> The H3 uses the same pin controller as previous SoC's from Allwinner.
>> Add support for the pins controlled by the main PIO controller.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>>  drivers/pinctrl/sunxi/Kconfig                      |   4 +
>>  drivers/pinctrl/sunxi/Makefile                     |   1 +
>>  drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
>>  4 files changed, 527 insertions(+)
>>  create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> index fdd8046..c46af8e 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> @@ -16,6 +16,7 @@ Required properties:
>>    "allwinner,sun7i-a20-pinctrl"
>>    "allwinner,sun8i-a23-pinctrl"
>>    "allwinner,sun8i-a23-r-pinctrl"
>> +  "allwinner,sun8i-h3-pinctrl"
>>  - reg: Should contain the register physical address and length for the
>>    pin controller.
>>  
>> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
>> index 2eb893e..c49e762 100644
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>> @@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
>>  	def_bool MACH_SUN8I
>>  	select PINCTRL_SUNXI_COMMON
>>  
>> +config PINCTRL_SUN8I_H3
>> +	def_bool MACH_SUN8I
>> +	select PINCTRL_SUNXI_COMMON
>> +
>>  config PINCTRL_SUN8I_A23_R
>>  	def_bool MACH_SUN8I
>>  	depends on RESET_CONTROLLER
>> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
>> index b796d57..fd4a068 100644
>> --- a/drivers/pinctrl/sunxi/Makefile
>> +++ b/drivers/pinctrl/sunxi/Makefile
>> @@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
>>  obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
>>  obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
>>  obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
>> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
>>  obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
>> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>> new file mode 100644
>> index 0000000..e20f511
>> --- /dev/null
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>> @@ -0,0 +1,521 @@
>> +/*
>> + * Allwinner H3 SoCs pinctrl driver.
>> + *
>> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
>> + *
>> + * Based on pinctrl-sun8i-a23.c, which is:
>> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
>> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
>> + *
>> + * This file is licensed under the terms of the GNU General Public
>> + * License version 2.  This program is licensed "as is" without any
>> + * warranty of any kind, whether express or implied.
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
>> +#include <linux/pinctrl/pinctrl.h>
>> +
>> +#include "pinctrl-sunxi.h"
>> +
>> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
>> +		  SUNXI_FUNCTION(0x3, "pwm0"),
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
> 
> The datasheet uses "SIM" for this, why have you changed the name here?

Thought I had changed that back. I first used scr because the
responsible module is called scr everywhere else (clocks, memory map).
Looks like I messed it up now and called the clocks "sim" instead...

I think I should also redo the dtsi and use scr for the clock again, to
stay compatible with how it was called in Manual and earlier sunxi SoCs.

Jens

> 
>> +		  SUNXI_FUNCTION(0x3, "pwm1"),
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
>> +		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
>> +		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
>> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
>> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
>> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
>> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
>> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
>> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
>> +};
>> +
>> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
>> +	.pins = sun8i_h3_pins,
>> +	.npins = ARRAY_SIZE(sun8i_h3_pins),
>> +	.irq_banks = 2,
>> +};
>> +
>> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
>> +{
>> +	return sunxi_pinctrl_init(pdev,
>> +				  &sun8i_h3_pinctrl_data);
>> +}
>> +
>> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
>> +	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
>> +	{}
>> +};
>> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
>> +
>> +static struct platform_driver sun8i_h3_pinctrl_driver = {
>> +	.probe	= sun8i_h3_pinctrl_probe,
>> +	.driver	= {
>> +		.name		= "sun8i-h3-pinctrl",
>> +		.of_match_table	= sun8i_h3_pinctrl_match,
>> +	},
>> +};
>> +module_platform_driver(sun8i_h3_pinctrl_driver);
>> +
>> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
>> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
>> +MODULE_LICENSE("GPL");
>> -- 
>> 2.3.7
>>
> 
> Looks good otherwise, thanks!
> 
> Maxime
> 

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

Hi,

On 06/05/15 12:11, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:30AM +0200, Jens Kuske wrote:
>> The H3 uses the same pin controller as previous SoC's from Allwinner.
>> Add support for the pins controlled by the main PIO controller.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>>  drivers/pinctrl/sunxi/Kconfig                      |   4 +
>>  drivers/pinctrl/sunxi/Makefile                     |   1 +
>>  drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
>>  4 files changed, 527 insertions(+)
>>  create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> index fdd8046..c46af8e 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> @@ -16,6 +16,7 @@ Required properties:
>>    "allwinner,sun7i-a20-pinctrl"
>>    "allwinner,sun8i-a23-pinctrl"
>>    "allwinner,sun8i-a23-r-pinctrl"
>> +  "allwinner,sun8i-h3-pinctrl"
>>  - reg: Should contain the register physical address and length for the
>>    pin controller.
>>  
>> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
>> index 2eb893e..c49e762 100644
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>> @@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
>>  	def_bool MACH_SUN8I
>>  	select PINCTRL_SUNXI_COMMON
>>  
>> +config PINCTRL_SUN8I_H3
>> +	def_bool MACH_SUN8I
>> +	select PINCTRL_SUNXI_COMMON
>> +
>>  config PINCTRL_SUN8I_A23_R
>>  	def_bool MACH_SUN8I
>>  	depends on RESET_CONTROLLER
>> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
>> index b796d57..fd4a068 100644
>> --- a/drivers/pinctrl/sunxi/Makefile
>> +++ b/drivers/pinctrl/sunxi/Makefile
>> @@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
>>  obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
>>  obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
>>  obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
>> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
>>  obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
>> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>> new file mode 100644
>> index 0000000..e20f511
>> --- /dev/null
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>> @@ -0,0 +1,521 @@
>> +/*
>> + * Allwinner H3 SoCs pinctrl driver.
>> + *
>> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
>> + *
>> + * Based on pinctrl-sun8i-a23.c, which is:
>> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
>> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
>> + *
>> + * This file is licensed under the terms of the GNU General Public
>> + * License version 2.  This program is licensed "as is" without any
>> + * warranty of any kind, whether express or implied.
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
>> +#include <linux/pinctrl/pinctrl.h>
>> +
>> +#include "pinctrl-sunxi.h"
>> +
>> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
>> +		  SUNXI_FUNCTION(0x3, "pwm0"),
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
> 
> The datasheet uses "SIM" for this, why have you changed the name here?

Thought I had changed that back. I first used scr because the
responsible module is called scr everywhere else (clocks, memory map).
Looks like I messed it up now and called the clocks "sim" instead...

I think I should also redo the dtsi and use scr for the clock again, to
stay compatible with how it was called in Manual and earlier sunxi SoCs.

Jens

> 
>> +		  SUNXI_FUNCTION(0x3, "pwm1"),
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
>> +		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
>> +		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
>> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
>> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
>> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
>> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
>> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
>> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
>> +};
>> +
>> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
>> +	.pins = sun8i_h3_pins,
>> +	.npins = ARRAY_SIZE(sun8i_h3_pins),
>> +	.irq_banks = 2,
>> +};
>> +
>> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
>> +{
>> +	return sunxi_pinctrl_init(pdev,
>> +				  &sun8i_h3_pinctrl_data);
>> +}
>> +
>> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
>> +	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
>> +	{}
>> +};
>> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
>> +
>> +static struct platform_driver sun8i_h3_pinctrl_driver = {
>> +	.probe	= sun8i_h3_pinctrl_probe,
>> +	.driver	= {
>> +		.name		= "sun8i-h3-pinctrl",
>> +		.of_match_table	= sun8i_h3_pinctrl_match,
>> +	},
>> +};
>> +module_platform_driver(sun8i_h3_pinctrl_driver);
>> +
>> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
>> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
>> +MODULE_LICENSE("GPL");
>> -- 
>> 2.3.7
>>
> 
> Looks good otherwise, thanks!
> 
> Maxime
> 

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

Hi,

On 06/05/15 12:11, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:30AM +0200, Jens Kuske wrote:
>> The H3 uses the same pin controller as previous SoC's from Allwinner.
>> Add support for the pins controlled by the main PIO controller.
>>
>> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>>  drivers/pinctrl/sunxi/Kconfig                      |   4 +
>>  drivers/pinctrl/sunxi/Makefile                     |   1 +
>>  drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c           | 521 +++++++++++++++++++++
>>  4 files changed, 527 insertions(+)
>>  create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> index fdd8046..c46af8e 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
>> @@ -16,6 +16,7 @@ Required properties:
>>    "allwinner,sun7i-a20-pinctrl"
>>    "allwinner,sun8i-a23-pinctrl"
>>    "allwinner,sun8i-a23-r-pinctrl"
>> +  "allwinner,sun8i-h3-pinctrl"
>>  - reg: Should contain the register physical address and length for the
>>    pin controller.
>>  
>> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
>> index 2eb893e..c49e762 100644
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>> @@ -38,6 +38,10 @@ config PINCTRL_SUN8I_A23
>>  	def_bool MACH_SUN8I
>>  	select PINCTRL_SUNXI_COMMON
>>  
>> +config PINCTRL_SUN8I_H3
>> +	def_bool MACH_SUN8I
>> +	select PINCTRL_SUNXI_COMMON
>> +
>>  config PINCTRL_SUN8I_A23_R
>>  	def_bool MACH_SUN8I
>>  	depends on RESET_CONTROLLER
>> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
>> index b796d57..fd4a068 100644
>> --- a/drivers/pinctrl/sunxi/Makefile
>> +++ b/drivers/pinctrl/sunxi/Makefile
>> @@ -11,4 +11,5 @@ obj-$(CONFIG_PINCTRL_SUN6I_A31_R)	+= pinctrl-sun6i-a31-r.o
>>  obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
>>  obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
>>  obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
>> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
>>  obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
>> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>> new file mode 100644
>> index 0000000..e20f511
>> --- /dev/null
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>> @@ -0,0 +1,521 @@
>> +/*
>> + * Allwinner H3 SoCs pinctrl driver.
>> + *
>> + * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> + *
>> + * Based on pinctrl-sun8i-a23.c, which is:
>> + * Copyright (C) 2014 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
>> + *
>> + * This file is licensed under the terms of the GNU General Public
>> + * License version 2.  This program is licensed "as is" without any
>> + * warranty of any kind, whether express or implied.
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
>> +#include <linux/pinctrl/pinctrl.h>
>> +
>> +#include "pinctrl-sunxi.h"
>> +
>> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* MS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* PA_EINT0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* CK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),	/* PA_EINT1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DO */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),	/* PA_EINT2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
>> +		  SUNXI_FUNCTION(0x3, "jtag"),		/* DI */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),	/* PA_EINT3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),	/* PA_EINT4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart0"),		/* RX */
>> +		  SUNXI_FUNCTION(0x3, "pwm0"),
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),	/* PA_EINT5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
> 
> The datasheet uses "SIM" for this, why have you changed the name here?

Thought I had changed that back. I first used scr because the
responsible module is called scr everywhere else (clocks, memory map).
Looks like I messed it up now and called the clocks "sim" instead...

I think I should also redo the dtsi and use scr for the clock again, to
stay compatible with how it was called in Manual and earlier sunxi SoCs.

Jens

> 
>> +		  SUNXI_FUNCTION(0x3, "pwm1"),
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),	/* PA_EINT6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),	/* PA_EINT7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DATA */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),	/* PA_EINT8 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* RST */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),	/* PA_EINT9 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "scr"),		/* DET */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),	/* PA_EINT10 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
>> +		  SUNXI_FUNCTION(0x3, "di"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),	/* PA_EINT11 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
>> +		  SUNXI_FUNCTION(0x3, "di"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)),	/* PA_EINT12 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CS */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)),	/* PA_EINT13 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)),	/* PA_EINT14 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MOSI */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* RTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)),	/* PA_EINT15 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spi1"),		/* MISO */
>> +		  SUNXI_FUNCTION(0x3, "uart3"),		/* CTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)),	/* PA_EINT16 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)),	/* PA_EINT17 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* SYNC */
>> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SCK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)),	/* PA_EINT18 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "i2c1"),		/* SDA */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)),	/* PA_EINT19 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DOUT */
>> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPEN */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)),	/* PA_EINT20 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s0"),		/* DIN */
>> +		  SUNXI_FUNCTION(0x3, "scr"),		/* VPPPP */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)),	/* PA_EINT21 */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* WE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MOSI */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* ALE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* MISO */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CLE */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* CE1 */
>> +		  SUNXI_FUNCTION(0x3, "spi0")),		/* CS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* CE0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RE */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* RB0 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0")),	/* RB1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ0 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ1 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ2 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ3 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ4 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand0"),		/* DQ5 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ6 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQ7 */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "nand"),		/* DQS */
>> +		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXD0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXCTL/RCDV */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* RXERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD2L */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXD0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CRS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXCTL/TXEN */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* TXERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* CLKIN/COL */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDC */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "emac")),		/* MDIO */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* PCLK */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* CLK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* MCLK */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* ERR */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* HSYNC */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* SYNC */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* VSYNC */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* DVLD */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D0 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D1 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D2 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D3 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D4 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D5 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D6 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* D7 */
>> +		  SUNXI_FUNCTION(0x3, "ts")),		/* D7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SCK */
>> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "csi"),		/* SDA */
>> +		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out")),
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* MS */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
>> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
>> +		  SUNXI_FUNCTION(0x3, "uart0")),	/* RX */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
>> +		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc0")),		/* DET */
>> +	/* Hole */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)),	/* PG_EINT0 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)),	/* PG_EINT1 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)),	/* PG_EINT2 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)),	/* PG_EINT3 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)),	/* PG_EINT4 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)),	/* PG_EINT5 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)),	/* PG_EINT6 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)),	/* PG_EINT7 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)),	/* PG_EINT8 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)),	/* PG_EINT9 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* SYNC */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)),	/* PG_EINT10 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* CLK */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)),	/* PG_EINT11 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DOUT */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)),	/* PG_EINT12 */
>> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
>> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
>> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
>> +		  SUNXI_FUNCTION(0x2, "i2s1"),		/* DIN */
>> +		  SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)),	/* PG_EINT13 */
>> +};
>> +
>> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
>> +	.pins = sun8i_h3_pins,
>> +	.npins = ARRAY_SIZE(sun8i_h3_pins),
>> +	.irq_banks = 2,
>> +};
>> +
>> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
>> +{
>> +	return sunxi_pinctrl_init(pdev,
>> +				  &sun8i_h3_pinctrl_data);
>> +}
>> +
>> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
>> +	{ .compatible = "allwinner,sun8i-h3-pinctrl", },
>> +	{}
>> +};
>> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
>> +
>> +static struct platform_driver sun8i_h3_pinctrl_driver = {
>> +	.probe	= sun8i_h3_pinctrl_probe,
>> +	.driver	= {
>> +		.name		= "sun8i-h3-pinctrl",
>> +		.of_match_table	= sun8i_h3_pinctrl_match,
>> +	},
>> +};
>> +module_platform_driver(sun8i_h3_pinctrl_driver);
>> +
>> +MODULE_AUTHOR("Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>");
>> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
>> +MODULE_LICENSE("GPL");
>> -- 
>> 2.3.7
>>
> 
> Looks good otherwise, thanks!
> 
> Maxime
> 

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 853 bytes --]

On Wed, May 06, 2015 at 12:34:30PM +0200, Jens Kuske wrote:
> >> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> >> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> >> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> >> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
> > 
> > The datasheet uses "SIM" for this, why have you changed the name here?
> 
> Thought I had changed that back. I first used scr because the
> responsible module is called scr everywhere else (clocks, memory map).
> Looks like I messed it up now and called the clocks "sim" instead...
> 
> I think I should also redo the dtsi and use scr for the clock again, to
> stay compatible with how it was called in Manual and earlier sunxi SoCs.

It seems reasonable :)

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

On Wed, May 06, 2015 at 12:34:30PM +0200, Jens Kuske wrote:
> >> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> >> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> >> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> >> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
> > 
> > The datasheet uses "SIM" for this, why have you changed the name here?
> 
> Thought I had changed that back. I first used scr because the
> responsible module is called scr everywhere else (clocks, memory map).
> Looks like I messed it up now and called the clocks "sim" instead...
> 
> I think I should also redo the dtsi and use scr for the clock again, to
> stay compatible with how it was called in Manual and earlier sunxi SoCs.

It seems reasonable :)

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150506/b855dfaf/attachment.sig>

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 828 bytes --]

On Wed, May 06, 2015 at 12:34:30PM +0200, Jens Kuske wrote:
> >> +	SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> >> +		  SUNXI_FUNCTION(0x0, "gpio_in"),
> >> +		  SUNXI_FUNCTION(0x1, "gpio_out"),
> >> +		  SUNXI_FUNCTION(0x2, "scr"),		/* PWREN */
> > 
> > The datasheet uses "SIM" for this, why have you changed the name here?
> 
> Thought I had changed that back. I first used scr because the
> responsible module is called scr everywhere else (clocks, memory map).
> Looks like I messed it up now and called the clocks "sim" instead...
> 
> I think I should also redo the dtsi and use scr for the clock again, to
> stay compatible with how it was called in Manual and earlier sunxi SoCs.

It seems reasonable :)

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Paul Bolle]

On Wed, 2015-05-06 at 11:31 +0200, Jens Kuske wrote:
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
 
> +config PINCTRL_SUN8I_H3
> +	def_bool MACH_SUN8I
> +	select PINCTRL_SUNXI_COMMON

> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile

> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o

PINCTRL_SUN8I_H3 is a bool symbol, so pinctrl-sun8i-h3.o will never be
part of a module, right?

(Note that PINCTRL_SUN8I_H3 appears to be an alias for MACH_SUN8I. Ie,
these two symbols operate in lockstep.)

> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

> +#include <linux/module.h>

> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);

> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> +MODULE_LICENSE("GPL");

This adds some module specific boilerplate. Was it perhaps your
intention to make PINCTRL_SUN8I_H3 a tristate symbol?

Thanks,


Paul Bolle

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Paul Bolle]

On Wed, 2015-05-06 at 11:31 +0200, Jens Kuske wrote:
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
 
> +config PINCTRL_SUN8I_H3
> +	def_bool MACH_SUN8I
> +	select PINCTRL_SUNXI_COMMON

> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile

> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o

PINCTRL_SUN8I_H3 is a bool symbol, so pinctrl-sun8i-h3.o will never be
part of a module, right?

(Note that PINCTRL_SUN8I_H3 appears to be an alias for MACH_SUN8I. Ie,
these two symbols operate in lockstep.)

> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

> +#include <linux/module.h>

> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);

> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> +MODULE_LICENSE("GPL");

This adds some module specific boilerplate. Was it perhaps your
intention to make PINCTRL_SUN8I_H3 a tristate symbol?

Thanks,


Paul Bolle

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Paul Bolle]

On Wed, 2015-05-06 at 11:31 +0200, Jens Kuske wrote:
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
 
> +config PINCTRL_SUN8I_H3
> +	def_bool MACH_SUN8I
> +	select PINCTRL_SUNXI_COMMON

> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile

> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o

PINCTRL_SUN8I_H3 is a bool symbol, so pinctrl-sun8i-h3.o will never be
part of a module, right?

(Note that PINCTRL_SUN8I_H3 appears to be an alias for MACH_SUN8I. Ie,
these two symbols operate in lockstep.)

> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c

> +#include <linux/module.h>

> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);

> +MODULE_AUTHOR("Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>");
> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> +MODULE_LICENSE("GPL");

This adds some module specific boilerplate. Was it perhaps your
intention to make PINCTRL_SUN8I_H3 a tristate symbol?

Thanks,


Paul Bolle

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

Hi,

On 07/05/15 10:10, Paul Bolle wrote:
> On Wed, 2015-05-06 at 11:31 +0200, Jens Kuske wrote:
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>  
>> +config PINCTRL_SUN8I_H3
>> +	def_bool MACH_SUN8I
>> +	select PINCTRL_SUNXI_COMMON
> 
>> --- a/drivers/pinctrl/sunxi/Makefile
>> +++ b/drivers/pinctrl/sunxi/Makefile
> 
>> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
> 
> PINCTRL_SUN8I_H3 is a bool symbol, so pinctrl-sun8i-h3.o will never be
> part of a module, right?
> 
> (Note that PINCTRL_SUN8I_H3 appears to be an alias for MACH_SUN8I. Ie,
> these two symbols operate in lockstep.)
> 
>> --- /dev/null
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> 
>> +#include <linux/module.h>
> 
>> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> 
>> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
>> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
>> +MODULE_LICENSE("GPL");
> 
> This adds some module specific boilerplate. Was it perhaps your
> intention to make PINCTRL_SUN8I_H3 a tristate symbol?
> 

I don't know to be honest, I just followed the pattern of all the other
pinctrl-sun?i-*.c files. But it sounds logical that this is needless
in the current state.

Looks like it got introduced when splitting up the driver:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/251712.html

Maybe there were plans to use separate modules some day. If not, we
should remove it from the other files as well I guess. Maxime, could
you please comment on that?

Regards,
Jens

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

Hi,

On 07/05/15 10:10, Paul Bolle wrote:
> On Wed, 2015-05-06 at 11:31 +0200, Jens Kuske wrote:
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>  
>> +config PINCTRL_SUN8I_H3
>> +	def_bool MACH_SUN8I
>> +	select PINCTRL_SUNXI_COMMON
> 
>> --- a/drivers/pinctrl/sunxi/Makefile
>> +++ b/drivers/pinctrl/sunxi/Makefile
> 
>> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
> 
> PINCTRL_SUN8I_H3 is a bool symbol, so pinctrl-sun8i-h3.o will never be
> part of a module, right?
> 
> (Note that PINCTRL_SUN8I_H3 appears to be an alias for MACH_SUN8I. Ie,
> these two symbols operate in lockstep.)
> 
>> --- /dev/null
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> 
>> +#include <linux/module.h>
> 
>> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> 
>> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
>> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
>> +MODULE_LICENSE("GPL");
> 
> This adds some module specific boilerplate. Was it perhaps your
> intention to make PINCTRL_SUN8I_H3 a tristate symbol?
> 

I don't know to be honest, I just followed the pattern of all the other
pinctrl-sun?i-*.c files. But it sounds logical that this is needless
in the current state.

Looks like it got introduced when splitting up the driver:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/251712.html

Maybe there were plans to use separate modules some day. If not, we
should remove it from the other files as well I guess. Maxime, could
you please comment on that?

Regards,
Jens

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Jens Kuske]

Hi,

On 07/05/15 10:10, Paul Bolle wrote:
> On Wed, 2015-05-06 at 11:31 +0200, Jens Kuske wrote:
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>  
>> +config PINCTRL_SUN8I_H3
>> +	def_bool MACH_SUN8I
>> +	select PINCTRL_SUNXI_COMMON
> 
>> --- a/drivers/pinctrl/sunxi/Makefile
>> +++ b/drivers/pinctrl/sunxi/Makefile
> 
>> +obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
> 
> PINCTRL_SUN8I_H3 is a bool symbol, so pinctrl-sun8i-h3.o will never be
> part of a module, right?
> 
> (Note that PINCTRL_SUN8I_H3 appears to be an alias for MACH_SUN8I. Ie,
> these two symbols operate in lockstep.)
> 
>> --- /dev/null
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> 
>> +#include <linux/module.h>
> 
>> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> 
>> +MODULE_AUTHOR("Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>");
>> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
>> +MODULE_LICENSE("GPL");
> 
> This adds some module specific boilerplate. Was it perhaps your
> intention to make PINCTRL_SUN8I_H3 a tristate symbol?
> 

I don't know to be honest, I just followed the pattern of all the other
pinctrl-sun?i-*.c files. But it sounds logical that this is needless
in the current state.

Looks like it got introduced when splitting up the driver:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/251712.html

Maybe there were plans to use separate modules some day. If not, we
should remove it from the other files as well I guess. Maxime, could
you please comment on that?

Regards,
Jens

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1094 bytes --]

On Sat, May 09, 2015 at 11:17:51AM +0200, Jens Kuske wrote:
> >> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> > 
> >> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
> >> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> >> +MODULE_LICENSE("GPL");
> > 
> > This adds some module specific boilerplate. Was it perhaps your
> > intention to make PINCTRL_SUN8I_H3 a tristate symbol?
> > 
> 
> I don't know to be honest, I just followed the pattern of all the other
> pinctrl-sun?i-*.c files. But it sounds logical that this is needless
> in the current state.
> 
> Looks like it got introduced when splitting up the driver:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/251712.html
> 
> Maybe there were plans to use separate modules some day. If not, we
> should remove it from the other files as well I guess. Maxime, could
> you please comment on that?

I don't see anything wrong with building those as modules.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

On Sat, May 09, 2015 at 11:17:51AM +0200, Jens Kuske wrote:
> >> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> > 
> >> +MODULE_AUTHOR("Jens Kuske <jenskuske@gmail.com>");
> >> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> >> +MODULE_LICENSE("GPL");
> > 
> > This adds some module specific boilerplate. Was it perhaps your
> > intention to make PINCTRL_SUN8I_H3 a tristate symbol?
> > 
> 
> I don't know to be honest, I just followed the pattern of all the other
> pinctrl-sun?i-*.c files. But it sounds logical that this is needless
> in the current state.
> 
> Looks like it got introduced when splitting up the driver:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/251712.html
> 
> Maybe there were plans to use separate modules some day. If not, we
> should remove it from the other files as well I guess. Maxime, could
> you please comment on that?

I don't see anything wrong with building those as modules.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150509/678baaea/attachment.sig>

Re: [PATCH 3/6] pinctrl: sunxi: Add H3 PIO controller support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1093 bytes --]

On Sat, May 09, 2015 at 11:17:51AM +0200, Jens Kuske wrote:
> >> +MODULE_DEVICE_TABLE(of, sun8i_h3_pinctrl_match);
> > 
> >> +MODULE_AUTHOR("Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>");
> >> +MODULE_DESCRIPTION("Allwinner H3 pinctrl driver");
> >> +MODULE_LICENSE("GPL");
> > 
> > This adds some module specific boilerplate. Was it perhaps your
> > intention to make PINCTRL_SUN8I_H3 a tristate symbol?
> > 
> 
> I don't know to be honest, I just followed the pattern of all the other
> pinctrl-sun?i-*.c files. But it sounds logical that this is needless
> in the current state.
> 
> Looks like it got introduced when splitting up the driver:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/251712.html
> 
> Maybe there were plans to use separate modules some day. If not, we
> should remove it from the other files as well I guess. Maxime, could
> you please comment on that?

I don't see anything wrong with building those as modules.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Jens Kuske]

The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 Documentation/devicetree/bindings/dma/sun6i-dma.txt |  5 ++++-
 drivers/dma/sun6i-dma.c                             | 12 ++++++++++++
 2 files changed, 16 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
index 9cdcba24d..d13c136 100644
--- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt
+++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -4,7 +4,10 @@ This driver follows the generic DMA bindings defined in dma.txt.
 
 Required properties:
 
-- compatible:	Must be "allwinner,sun6i-a31-dma" or "allwinner,sun8i-a23-dma"
+- compatible:	Must be one of
+		  "allwinner,sun6i-a31-dma"
+		  "allwinner,sun8i-a23-dma"
+		  "allwinner,sun8i-h3-dma"
 - reg:		Should contain the registers base address and length
 - interrupts:	Should contain a reference to the interrupt used by this device
 - clocks:	Should contain a reference to the parent AHB clock
diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index 11e5365..842ff97 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -891,9 +891,21 @@ static struct sun6i_dma_config sun8i_a23_dma_cfg = {
 	.nr_max_vchans   = 37,
 };
 
+/*
+ * The H3 has 12 physical channels, a maximum DRQ port id of 27,
+ * and a total of 34 usable source and destination endpoints.
+ */
+
+static struct sun6i_dma_config sun8i_h3_dma_cfg = {
+	.nr_max_channels = 12,
+	.nr_max_requests = 27,
+	.nr_max_vchans   = 34,
+};
+
 static const struct of_device_id sun6i_dma_match[] = {
 	{ .compatible = "allwinner,sun6i-a31-dma", .data = &sun6i_a31_dma_cfg },
 	{ .compatible = "allwinner,sun8i-a23-dma", .data = &sun8i_a23_dma_cfg },
+	{ .compatible = "allwinner,sun8i-h3-dma", .data = &sun8i_h3_dma_cfg },
 	{ /* sentinel */ }
 };
 
-- 
2.3.7

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Jens Kuske]

The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 Documentation/devicetree/bindings/dma/sun6i-dma.txt |  5 ++++-
 drivers/dma/sun6i-dma.c                             | 12 ++++++++++++
 2 files changed, 16 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
index 9cdcba24d..d13c136 100644
--- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt
+++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -4,7 +4,10 @@ This driver follows the generic DMA bindings defined in dma.txt.
 
 Required properties:
 
-- compatible:	Must be "allwinner,sun6i-a31-dma" or "allwinner,sun8i-a23-dma"
+- compatible:	Must be one of
+		  "allwinner,sun6i-a31-dma"
+		  "allwinner,sun8i-a23-dma"
+		  "allwinner,sun8i-h3-dma"
 - reg:		Should contain the registers base address and length
 - interrupts:	Should contain a reference to the interrupt used by this device
 - clocks:	Should contain a reference to the parent AHB clock
diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index 11e5365..842ff97 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -891,9 +891,21 @@ static struct sun6i_dma_config sun8i_a23_dma_cfg = {
 	.nr_max_vchans   = 37,
 };
 
+/*
+ * The H3 has 12 physical channels, a maximum DRQ port id of 27,
+ * and a total of 34 usable source and destination endpoints.
+ */
+
+static struct sun6i_dma_config sun8i_h3_dma_cfg = {
+	.nr_max_channels = 12,
+	.nr_max_requests = 27,
+	.nr_max_vchans   = 34,
+};
+
 static const struct of_device_id sun6i_dma_match[] = {
 	{ .compatible = "allwinner,sun6i-a31-dma", .data = &sun6i_a31_dma_cfg },
 	{ .compatible = "allwinner,sun8i-a23-dma", .data = &sun8i_a23_dma_cfg },
+	{ .compatible = "allwinner,sun8i-h3-dma", .data = &sun8i_h3_dma_cfg },
 	{ /* sentinel */ }
 };
 
-- 
2.3.7

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Jens Kuske]

The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.

Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 Documentation/devicetree/bindings/dma/sun6i-dma.txt |  5 ++++-
 drivers/dma/sun6i-dma.c                             | 12 ++++++++++++
 2 files changed, 16 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
index 9cdcba24d..d13c136 100644
--- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt
+++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -4,7 +4,10 @@ This driver follows the generic DMA bindings defined in dma.txt.
 
 Required properties:
 
-- compatible:	Must be "allwinner,sun6i-a31-dma" or "allwinner,sun8i-a23-dma"
+- compatible:	Must be one of
+		  "allwinner,sun6i-a31-dma"
+		  "allwinner,sun8i-a23-dma"
+		  "allwinner,sun8i-h3-dma"
 - reg:		Should contain the registers base address and length
 - interrupts:	Should contain a reference to the interrupt used by this device
 - clocks:	Should contain a reference to the parent AHB clock
diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index 11e5365..842ff97 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -891,9 +891,21 @@ static struct sun6i_dma_config sun8i_a23_dma_cfg = {
 	.nr_max_vchans   = 37,
 };
 
+/*
+ * The H3 has 12 physical channels, a maximum DRQ port id of 27,
+ * and a total of 34 usable source and destination endpoints.
+ */
+
+static struct sun6i_dma_config sun8i_h3_dma_cfg = {
+	.nr_max_channels = 12,
+	.nr_max_requests = 27,
+	.nr_max_vchans   = 34,
+};
+
 static const struct of_device_id sun6i_dma_match[] = {
 	{ .compatible = "allwinner,sun6i-a31-dma", .data = &sun6i_a31_dma_cfg },
 	{ .compatible = "allwinner,sun8i-a23-dma", .data = &sun8i_a23_dma_cfg },
+	{ .compatible = "allwinner,sun8i-h3-dma", .data = &sun8i_h3_dma_cfg },
 	{ /* sentinel */ }
 };
 
-- 
2.3.7

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 496 bytes --]

On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> The H3 SoC has the same dma engine as the A31 (sun6i), with a
> reduced amount of endpoints and physical channels. Add the proper
> config data and compatible string to support it.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>

Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Maxime Ripard]

On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> The H3 SoC has the same dma engine as the A31 (sun6i), with a
> reduced amount of endpoints and physical channels. Add the proper
> config data and compatible string to support it.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>

Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150506/e9f37fc3/attachment-0001.sig>

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 540 bytes --]

On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> The H3 SoC has the same dma engine as the A31 (sun6i), with a
> reduced amount of endpoints and physical channels. Add the proper
> config data and compatible string to support it.
> 
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Vinod Koul]

On Wed, May 06, 2015 at 12:13:42PM +0200, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> > The H3 SoC has the same dma engine as the A31 (sun6i), with a
> > reduced amount of endpoints and physical channels. Add the proper
> > config data and compatible string to support it.
> > 
> > Signed-off-by: Jens Kuske <jenskuske@gmail.com>

This looks fine to me, I think can be merged now. Do you guys want the
mainatainers to pick up patches to their subsystem or merge them tgether,
though don't see any dependency though

-- 
~Vinod

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Vinod Koul]

On Wed, May 06, 2015 at 12:13:42PM +0200, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> > The H3 SoC has the same dma engine as the A31 (sun6i), with a
> > reduced amount of endpoints and physical channels. Add the proper
> > config data and compatible string to support it.
> > 
> > Signed-off-by: Jens Kuske <jenskuske@gmail.com>

This looks fine to me, I think can be merged now. Do you guys want the
mainatainers to pick up patches to their subsystem or merge them tgether,
though don't see any dependency though

-- 
~Vinod

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Vinod Koul]

On Wed, May 06, 2015 at 12:13:42PM +0200, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> > The H3 SoC has the same dma engine as the A31 (sun6i), with a
> > reduced amount of endpoints and physical channels. Add the proper
> > config data and compatible string to support it.
> > 
> > Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

This looks fine to me, I think can be merged now. Do you guys want the
mainatainers to pick up patches to their subsystem or merge them tgether,
though don't see any dependency though

-- 
~Vinod

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 897 bytes --]

Hi Vinod,

On Fri, May 08, 2015 at 09:14:26AM +0530, Vinod Koul wrote:
> On Wed, May 06, 2015 at 12:13:42PM +0200, Maxime Ripard wrote:
> > On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> > > The H3 SoC has the same dma engine as the A31 (sun6i), with a
> > > reduced amount of endpoints and physical channels. Add the proper
> > > config data and compatible string to support it.
> > > 
> > > Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> 
> This looks fine to me, I think can be merged now. Do you guys want the
> mainatainers to pick up patches to their subsystem or merge them tgether,
> though don't see any dependency though

It can be merged through your tree, like you said there's no
particular dependencies on our side.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Maxime Ripard]

Hi Vinod,

On Fri, May 08, 2015 at 09:14:26AM +0530, Vinod Koul wrote:
> On Wed, May 06, 2015 at 12:13:42PM +0200, Maxime Ripard wrote:
> > On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> > > The H3 SoC has the same dma engine as the A31 (sun6i), with a
> > > reduced amount of endpoints and physical channels. Add the proper
> > > config data and compatible string to support it.
> > > 
> > > Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> 
> This looks fine to me, I think can be merged now. Do you guys want the
> mainatainers to pick up patches to their subsystem or merge them tgether,
> though don't see any dependency though

It can be merged through your tree, like you said there's no
particular dependencies on our side.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150508/93fe6653/attachment-0001.sig>

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 901 bytes --]

Hi Vinod,

On Fri, May 08, 2015 at 09:14:26AM +0530, Vinod Koul wrote:
> On Wed, May 06, 2015 at 12:13:42PM +0200, Maxime Ripard wrote:
> > On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> > > The H3 SoC has the same dma engine as the A31 (sun6i), with a
> > > reduced amount of endpoints and physical channels. Add the proper
> > > config data and compatible string to support it.
> > > 
> > > Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> 
> This looks fine to me, I think can be merged now. Do you guys want the
> mainatainers to pick up patches to their subsystem or merge them tgether,
> though don't see any dependency though

It can be merged through your tree, like you said there's no
particular dependencies on our side.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Vinod Koul]

On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> The H3 SoC has the same dma engine as the A31 (sun6i), with a
> reduced amount of endpoints and physical channels. Add the proper
> config data and compatible string to support it.
Applied, thanks

-- 
~Vinod

[PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Vinod Koul]

On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> The H3 SoC has the same dma engine as the A31 (sun6i), with a
> reduced amount of endpoints and physical channels. Add the proper
> config data and compatible string to support it.
Applied, thanks

-- 
~Vinod

Re: [PATCH 4/6] dmaengine: sun6i: Add support for Allwinner H3 (sun8i) variant

[Vinod Koul]

On Wed, May 06, 2015 at 11:31:31AM +0200, Jens Kuske wrote:
> The H3 SoC has the same dma engine as the A31 (sun6i), with a
> reduced amount of endpoints and physical channels. Add the proper
> config data and compatible string to support it.
Applied, thanks

-- 
~Vinod

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Jens Kuske]

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 468 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi

diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
new file mode 100644
index 0000000..53aab95
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -0,0 +1,468 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+
+		pll1: clk@01c20000 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-a23-pll1-clk";
+			reg = <0x01c20000 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll1";
+		};
+
+		pll6: clk@01c20028 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-pll6-clk";
+			reg = <0x01c20028 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll6", "pll6x2", "pll6d2";
+		};
+
+		pll8: clk@01c20044 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-pll8-clk";
+			reg = <0x01c20044 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll8";
+		};
+
+		cpu: cpu_clk@01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-cpu-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+			clock-output-names = "cpu";
+		};
+
+		axi: axi_clk@01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-axi-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&cpu>;
+			clock-output-names = "axi";
+		};
+
+		ahb1: ahb1_clk@01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun6i-a31-ahb1-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+			clock-output-names = "ahb1";
+		};
+
+		ahb2: ahb2_clk@01c2005c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-ahb2-clk";
+			reg = <0x01c2005c 0x4>;
+			clocks = <&ahb1>, <&pll6 2>;
+			clock-output-names = "ahb2";
+		};
+
+		apb1: apb1_clk@01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb0-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&ahb1>;
+			clock-output-names = "apb1";
+		};
+
+		apb2: apb2_clk@01c20058 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb1-clk";
+			reg = <0x01c20058 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+			clock-output-names = "apb2";
+		};
+
+		ahb1_gates: ahb1_gates_clk@01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
+			reg = <0x01c20060 0x14>;
+			clocks = <&ahb1>;
+			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
+					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
+					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
+					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
+					"ahb1_otg_ehci0", "ahb1_ehic1",
+					"ahb1_ehic2", "ahb1_ehic3",
+					"ahb1_otg_ohci0", "ahb1_ve",
+					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
+					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
+					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
+					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
+		};
+
+		ahb2_gates: ahb2_gates_clk@01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
+			reg = <0x01c20060 0x4>;
+			clocks = <&ahb2>;
+			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
+					"ahb2_ohic2", "ahb2_ohic3";
+		};
+
+		apb1_gates: clk@01c20068 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
+			reg = <0x01c20068 0x4>;
+			clocks = <&apb1>;
+			clock-output-names = "apb1_codec", "apb1_spdif",
+					"apb1_pio", "apb1_ths", "apb1_i2s0",
+					"apb1_i2s1", "apb1_i2s2";
+		};
+
+		apb2_gates: clk@01c2006c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
+			reg = <0x01c2006c 0x4>;
+			clocks = <&apb2>;
+			clock-output-names = "apb2_i2c0", "apb2_i2c1",
+					"apb2_i2c2", "apb2_uart0",
+					"apb2_uart1", "apb2_uart2",
+					"apb2_uart3", "apb2_sim";
+		};
+
+		mmc0_clk: clk@01c20088 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20088 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc0",
+					     "mmc0_output",
+					     "mmc0_sample";
+		};
+
+		mmc1_clk: clk@01c2008c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c2008c 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc1",
+					     "mmc1_output",
+					     "mmc1_sample";
+		};
+
+		mmc2_clk: clk@01c20090 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20090 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc2",
+					     "mmc2_output",
+					     "mmc2_sample";
+		};
+	};
+
+	soc@01c00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dma: dma-controller@01c02000 {
+			compatible = "allwinner,sun8i-h3-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ahb1_gates 6>;
+			resets = <&ahb12_rst 6>;
+			#dma-cells = <1>;
+		};
+
+		mmc0: mmc@01c0f000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ahb1_gates 8>,
+				 <&mmc0_clk 0>,
+				 <&mmc0_clk 1>,
+				 <&mmc0_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 8>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc1: mmc@01c10000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ahb1_gates 9>,
+				 <&mmc1_clk 0>,
+				 <&mmc1_clk 1>,
+				 <&mmc1_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 9>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@01c11000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ahb1_gates 10>,
+				 <&mmc2_clk 0>,
+				 <&mmc2_clk 1>,
+				 <&mmc2_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 10>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pio: pinctrl@01c20800 {
+			compatible = "allwinner,sun8i-h3-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apb1_gates 5>;
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			#size-cells = <0>;
+			#gpio-cells = <3>;
+
+			uart0_pins_a: uart0@0 {
+				allwinner,pins = "PA4", "PA5";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_pins_a: mmc0@0 {
+				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+				allwinner,function = "mmc0";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_cd_pin: mmc0_cd_pin@0 {
+				allwinner,pins = "PF6";
+				allwinner,function = "gpio_in";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
+
+			mmc1_pins_a: mmc1@0 {
+				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
+				allwinner,function = "mmc1";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+		};
+
+		ahb12_rst: reset@01c202c0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202c0 0xc>;
+		};
+
+		apb1_rst: reset@01c202d0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d0 0x4>;
+		};
+
+		apb2_rst: reset@01c202d8 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d8 0x4>;
+		};
+
+		timer@01c20c00 {
+			compatible = "allwinner,sun4i-a10-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		wdt0: watchdog@01c20ca0 {
+			compatible = "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart0: serial@01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 16>;
+			resets = <&apb2_rst 16>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart1: serial@01c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 17>;
+			resets = <&apb2_rst 17>;
+			dmas = <&dma 7>, <&dma 7>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart2: serial@01c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 18>;
+			resets = <&apb2_rst 18>;
+			dmas = <&dma 8>, <&dma 8>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart3: serial@01c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 19>;
+			resets = <&apb2_rst 19>;
+			dmas = <&dma 9>, <&dma 9>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		rtc: rtc@01f00000 {
+			compatible = "allwinner,sun6i-a31-rtc";
+			reg = <0x01f00000 0x54>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};
-- 
2.3.7

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Jens Kuske]

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 468 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi

diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
new file mode 100644
index 0000000..53aab95
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -0,0 +1,468 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu at 1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu at 2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu at 3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+
+		pll1: clk at 01c20000 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-a23-pll1-clk";
+			reg = <0x01c20000 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll1";
+		};
+
+		pll6: clk at 01c20028 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-pll6-clk";
+			reg = <0x01c20028 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll6", "pll6x2", "pll6d2";
+		};
+
+		pll8: clk at 01c20044 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-pll8-clk";
+			reg = <0x01c20044 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll8";
+		};
+
+		cpu: cpu_clk at 01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-cpu-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+			clock-output-names = "cpu";
+		};
+
+		axi: axi_clk at 01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-axi-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&cpu>;
+			clock-output-names = "axi";
+		};
+
+		ahb1: ahb1_clk at 01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun6i-a31-ahb1-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+			clock-output-names = "ahb1";
+		};
+
+		ahb2: ahb2_clk at 01c2005c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-ahb2-clk";
+			reg = <0x01c2005c 0x4>;
+			clocks = <&ahb1>, <&pll6 2>;
+			clock-output-names = "ahb2";
+		};
+
+		apb1: apb1_clk at 01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb0-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&ahb1>;
+			clock-output-names = "apb1";
+		};
+
+		apb2: apb2_clk at 01c20058 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb1-clk";
+			reg = <0x01c20058 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+			clock-output-names = "apb2";
+		};
+
+		ahb1_gates: ahb1_gates_clk at 01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
+			reg = <0x01c20060 0x14>;
+			clocks = <&ahb1>;
+			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
+					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
+					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
+					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
+					"ahb1_otg_ehci0", "ahb1_ehic1",
+					"ahb1_ehic2", "ahb1_ehic3",
+					"ahb1_otg_ohci0", "ahb1_ve",
+					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
+					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
+					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
+					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
+		};
+
+		ahb2_gates: ahb2_gates_clk at 01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
+			reg = <0x01c20060 0x4>;
+			clocks = <&ahb2>;
+			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
+					"ahb2_ohic2", "ahb2_ohic3";
+		};
+
+		apb1_gates: clk at 01c20068 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
+			reg = <0x01c20068 0x4>;
+			clocks = <&apb1>;
+			clock-output-names = "apb1_codec", "apb1_spdif",
+					"apb1_pio", "apb1_ths", "apb1_i2s0",
+					"apb1_i2s1", "apb1_i2s2";
+		};
+
+		apb2_gates: clk at 01c2006c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
+			reg = <0x01c2006c 0x4>;
+			clocks = <&apb2>;
+			clock-output-names = "apb2_i2c0", "apb2_i2c1",
+					"apb2_i2c2", "apb2_uart0",
+					"apb2_uart1", "apb2_uart2",
+					"apb2_uart3", "apb2_sim";
+		};
+
+		mmc0_clk: clk at 01c20088 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20088 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc0",
+					     "mmc0_output",
+					     "mmc0_sample";
+		};
+
+		mmc1_clk: clk at 01c2008c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c2008c 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc1",
+					     "mmc1_output",
+					     "mmc1_sample";
+		};
+
+		mmc2_clk: clk at 01c20090 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20090 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc2",
+					     "mmc2_output",
+					     "mmc2_sample";
+		};
+	};
+
+	soc at 01c00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dma: dma-controller at 01c02000 {
+			compatible = "allwinner,sun8i-h3-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ahb1_gates 6>;
+			resets = <&ahb12_rst 6>;
+			#dma-cells = <1>;
+		};
+
+		mmc0: mmc at 01c0f000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ahb1_gates 8>,
+				 <&mmc0_clk 0>,
+				 <&mmc0_clk 1>,
+				 <&mmc0_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 8>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc1: mmc at 01c10000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ahb1_gates 9>,
+				 <&mmc1_clk 0>,
+				 <&mmc1_clk 1>,
+				 <&mmc1_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 9>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc2: mmc at 01c11000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ahb1_gates 10>,
+				 <&mmc2_clk 0>,
+				 <&mmc2_clk 1>,
+				 <&mmc2_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 10>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pio: pinctrl at 01c20800 {
+			compatible = "allwinner,sun8i-h3-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apb1_gates 5>;
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			#size-cells = <0>;
+			#gpio-cells = <3>;
+
+			uart0_pins_a: uart0 at 0 {
+				allwinner,pins = "PA4", "PA5";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_pins_a: mmc0 at 0 {
+				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+				allwinner,function = "mmc0";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_cd_pin: mmc0_cd_pin at 0 {
+				allwinner,pins = "PF6";
+				allwinner,function = "gpio_in";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
+
+			mmc1_pins_a: mmc1 at 0 {
+				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
+				allwinner,function = "mmc1";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+		};
+
+		ahb12_rst: reset at 01c202c0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202c0 0xc>;
+		};
+
+		apb1_rst: reset at 01c202d0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d0 0x4>;
+		};
+
+		apb2_rst: reset at 01c202d8 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d8 0x4>;
+		};
+
+		timer at 01c20c00 {
+			compatible = "allwinner,sun4i-a10-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		wdt0: watchdog at 01c20ca0 {
+			compatible = "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart0: serial at 01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 16>;
+			resets = <&apb2_rst 16>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart1: serial at 01c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 17>;
+			resets = <&apb2_rst 17>;
+			dmas = <&dma 7>, <&dma 7>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart2: serial at 01c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 18>;
+			resets = <&apb2_rst 18>;
+			dmas = <&dma 8>, <&dma 8>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart3: serial at 01c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 19>;
+			resets = <&apb2_rst 19>;
+			dmas = <&dma 9>, <&dma 9>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		gic: interrupt-controller at 01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		rtc: rtc at 01f00000 {
+			compatible = "allwinner,sun6i-a31-rtc";
+			reg = <0x01f00000 0x54>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};
-- 
2.3.7

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Jens Kuske]

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.

Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 468 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi

diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
new file mode 100644
index 0000000..53aab95
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -0,0 +1,468 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+
+		pll1: clk@01c20000 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-a23-pll1-clk";
+			reg = <0x01c20000 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll1";
+		};
+
+		pll6: clk@01c20028 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-pll6-clk";
+			reg = <0x01c20028 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll6", "pll6x2", "pll6d2";
+		};
+
+		pll8: clk@01c20044 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-pll8-clk";
+			reg = <0x01c20044 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll8";
+		};
+
+		cpu: cpu_clk@01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-cpu-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+			clock-output-names = "cpu";
+		};
+
+		axi: axi_clk@01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-axi-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&cpu>;
+			clock-output-names = "axi";
+		};
+
+		ahb1: ahb1_clk@01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun6i-a31-ahb1-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+			clock-output-names = "ahb1";
+		};
+
+		ahb2: ahb2_clk@01c2005c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-ahb2-clk";
+			reg = <0x01c2005c 0x4>;
+			clocks = <&ahb1>, <&pll6 2>;
+			clock-output-names = "ahb2";
+		};
+
+		apb1: apb1_clk@01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb0-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&ahb1>;
+			clock-output-names = "apb1";
+		};
+
+		apb2: apb2_clk@01c20058 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb1-clk";
+			reg = <0x01c20058 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+			clock-output-names = "apb2";
+		};
+
+		ahb1_gates: ahb1_gates_clk@01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
+			reg = <0x01c20060 0x14>;
+			clocks = <&ahb1>;
+			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
+					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
+					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
+					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
+					"ahb1_otg_ehci0", "ahb1_ehic1",
+					"ahb1_ehic2", "ahb1_ehic3",
+					"ahb1_otg_ohci0", "ahb1_ve",
+					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
+					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
+					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
+					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
+		};
+
+		ahb2_gates: ahb2_gates_clk@01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
+			reg = <0x01c20060 0x4>;
+			clocks = <&ahb2>;
+			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
+					"ahb2_ohic2", "ahb2_ohic3";
+		};
+
+		apb1_gates: clk@01c20068 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
+			reg = <0x01c20068 0x4>;
+			clocks = <&apb1>;
+			clock-output-names = "apb1_codec", "apb1_spdif",
+					"apb1_pio", "apb1_ths", "apb1_i2s0",
+					"apb1_i2s1", "apb1_i2s2";
+		};
+
+		apb2_gates: clk@01c2006c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
+			reg = <0x01c2006c 0x4>;
+			clocks = <&apb2>;
+			clock-output-names = "apb2_i2c0", "apb2_i2c1",
+					"apb2_i2c2", "apb2_uart0",
+					"apb2_uart1", "apb2_uart2",
+					"apb2_uart3", "apb2_sim";
+		};
+
+		mmc0_clk: clk@01c20088 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20088 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc0",
+					     "mmc0_output",
+					     "mmc0_sample";
+		};
+
+		mmc1_clk: clk@01c2008c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c2008c 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc1",
+					     "mmc1_output",
+					     "mmc1_sample";
+		};
+
+		mmc2_clk: clk@01c20090 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20090 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc2",
+					     "mmc2_output",
+					     "mmc2_sample";
+		};
+	};
+
+	soc@01c00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dma: dma-controller@01c02000 {
+			compatible = "allwinner,sun8i-h3-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ahb1_gates 6>;
+			resets = <&ahb12_rst 6>;
+			#dma-cells = <1>;
+		};
+
+		mmc0: mmc@01c0f000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ahb1_gates 8>,
+				 <&mmc0_clk 0>,
+				 <&mmc0_clk 1>,
+				 <&mmc0_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 8>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc1: mmc@01c10000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ahb1_gates 9>,
+				 <&mmc1_clk 0>,
+				 <&mmc1_clk 1>,
+				 <&mmc1_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 9>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@01c11000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ahb1_gates 10>,
+				 <&mmc2_clk 0>,
+				 <&mmc2_clk 1>,
+				 <&mmc2_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb12_rst 10>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pio: pinctrl@01c20800 {
+			compatible = "allwinner,sun8i-h3-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apb1_gates 5>;
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			#size-cells = <0>;
+			#gpio-cells = <3>;
+
+			uart0_pins_a: uart0@0 {
+				allwinner,pins = "PA4", "PA5";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_pins_a: mmc0@0 {
+				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+				allwinner,function = "mmc0";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_cd_pin: mmc0_cd_pin@0 {
+				allwinner,pins = "PF6";
+				allwinner,function = "gpio_in";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
+
+			mmc1_pins_a: mmc1@0 {
+				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
+				allwinner,function = "mmc1";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+		};
+
+		ahb12_rst: reset@01c202c0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202c0 0xc>;
+		};
+
+		apb1_rst: reset@01c202d0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d0 0x4>;
+		};
+
+		apb2_rst: reset@01c202d8 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d8 0x4>;
+		};
+
+		timer@01c20c00 {
+			compatible = "allwinner,sun4i-a10-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		wdt0: watchdog@01c20ca0 {
+			compatible = "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart0: serial@01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 16>;
+			resets = <&apb2_rst 16>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart1: serial@01c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 17>;
+			resets = <&apb2_rst 17>;
+			dmas = <&dma 7>, <&dma 7>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart2: serial@01c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 18>;
+			resets = <&apb2_rst 18>;
+			dmas = <&dma 8>, <&dma 8>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart3: serial@01c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb2_gates 19>;
+			resets = <&apb2_rst 19>;
+			dmas = <&dma 9>, <&dma 9>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		rtc: rtc@01f00000 {
+			compatible = "allwinner,sun6i-a31-rtc";
+			reg = <0x01f00000 0x54>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};
-- 
2.3.7

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 15847 bytes --]

On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 468 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> new file mode 100644
> index 0000000..53aab95
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -0,0 +1,468 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + *     You should have received a copy of the GNU General Public
> + *     License along with this file; if not, write to the Free
> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> + *     MA 02110-1301 USA

Could you remove that last paragraph?
It generates a checkpatch warning.

> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu@0 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +
> +		cpu@1 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <1>;
> +		};
> +
> +		cpu@2 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <2>;
> +		};
> +
> +		cpu@3 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <3>;
> +		};
> +	};
> +
> +	memory {
> +		reg = <0x40000000 0x80000000>;
> +	};
> +
> +	clocks {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		osc24M: osc24M_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <24000000>;
> +			clock-output-names = "osc24M";
> +		};
> +
> +		osc32k: osc32k_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <32768>;
> +			clock-output-names = "osc32k";
> +		};
> +
> +		pll1: clk@01c20000 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-a23-pll1-clk";
> +			reg = <0x01c20000 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll1";
> +		};
> +
> +		pll6: clk@01c20028 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-pll6-clk";
> +			reg = <0x01c20028 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll6", "pll6x2", "pll6d2";
> +		};
> +
> +		pll8: clk@01c20044 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-pll8-clk";
> +			reg = <0x01c20044 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll8";
> +		};
> +
> +		cpu: cpu_clk@01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-cpu-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
> +			clock-output-names = "cpu";
> +		};
> +
> +		axi: axi_clk@01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-axi-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&cpu>;
> +			clock-output-names = "axi";
> +		};
> +
> +		ahb1: ahb1_clk@01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
> +			clock-output-names = "ahb1";
> +		};
> +
> +		ahb2: ahb2_clk@01c2005c {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
> +			reg = <0x01c2005c 0x4>;
> +			clocks = <&ahb1>, <&pll6 2>;
> +			clock-output-names = "ahb2";
> +		};
> +
> +		apb1: apb1_clk@01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb0-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "apb1";
> +		};
> +
> +		apb2: apb2_clk@01c20058 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb1-clk";
> +			reg = <0x01c20058 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
> +			clock-output-names = "apb2";
> +		};
> +
> +		ahb1_gates: ahb1_gates_clk@01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
> +			reg = <0x01c20060 0x14>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
> +					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
> +					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
> +					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
> +					"ahb1_otg_ehci0", "ahb1_ehic1",
> +					"ahb1_ehic2", "ahb1_ehic3",
> +					"ahb1_otg_ohci0", "ahb1_ve",
> +					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
> +					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
> +					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
> +					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
> +		};
> +
> +		ahb2_gates: ahb2_gates_clk@01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
> +			reg = <0x01c20060 0x4>;
> +			clocks = <&ahb2>;
> +			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
> +					"ahb2_ohic2", "ahb2_ohic3";
> +		};
> +
> +		apb1_gates: clk@01c20068 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
> +			reg = <0x01c20068 0x4>;
> +			clocks = <&apb1>;
> +			clock-output-names = "apb1_codec", "apb1_spdif",
> +					"apb1_pio", "apb1_ths", "apb1_i2s0",
> +					"apb1_i2s1", "apb1_i2s2";
> +		};
> +
> +		apb2_gates: clk@01c2006c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
> +			reg = <0x01c2006c 0x4>;
> +			clocks = <&apb2>;
> +			clock-output-names = "apb2_i2c0", "apb2_i2c1",
> +					"apb2_i2c2", "apb2_uart0",
> +					"apb2_uart1", "apb2_uart2",
> +					"apb2_uart3", "apb2_sim";

I'd prefer if the clocks on a new line were right-aligned (like you
did for the mmc clocks just below).

> +		};
> +
> +		mmc0_clk: clk@01c20088 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20088 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc0",
> +					     "mmc0_output",
> +					     "mmc0_sample";
> +		};
> +
> +		mmc1_clk: clk@01c2008c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c2008c 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc1",
> +					     "mmc1_output",
> +					     "mmc1_sample";
> +		};
> +
> +		mmc2_clk: clk@01c20090 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20090 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc2",
> +					     "mmc2_output",
> +					     "mmc2_sample";
> +		};
> +	};
> +
> +	soc@01c00000 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		dma: dma-controller@01c02000 {
> +			compatible = "allwinner,sun8i-h3-dma";
> +			reg = <0x01c02000 0x1000>;
> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ahb1_gates 6>;
> +			resets = <&ahb12_rst 6>;
> +			#dma-cells = <1>;
> +		};
> +
> +		mmc0: mmc@01c0f000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c0f000 0x1000>;
> +			clocks = <&ahb1_gates 8>,
> +				 <&mmc0_clk 0>,
> +				 <&mmc0_clk 1>,
> +				 <&mmc0_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 8>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		mmc1: mmc@01c10000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c10000 0x1000>;
> +			clocks = <&ahb1_gates 9>,
> +				 <&mmc1_clk 0>,
> +				 <&mmc1_clk 1>,
> +				 <&mmc1_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 9>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		mmc2: mmc@01c11000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c11000 0x1000>;
> +			clocks = <&ahb1_gates 10>,
> +				 <&mmc2_clk 0>,
> +				 <&mmc2_clk 1>,
> +				 <&mmc2_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 10>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		pio: pinctrl@01c20800 {
> +			compatible = "allwinner,sun8i-h3-pinctrl";
> +			reg = <0x01c20800 0x400>;
> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&apb1_gates 5>;
> +			gpio-controller;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			#size-cells = <0>;
> +			#gpio-cells = <3>;
> +
> +			uart0_pins_a: uart0@0 {
> +				allwinner,pins = "PA4", "PA5";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_pins_a: mmc0@0 {
> +				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";

Could you have spaces between the commas, and wrap the line at 80
chars?

> +				allwinner,function = "mmc0";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_cd_pin: mmc0_cd_pin@0 {
> +				allwinner,pins = "PF6";
> +				allwinner,function = "gpio_in";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +			};
> +
> +			mmc1_pins_a: mmc1@0 {
> +				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
> +				allwinner,function = "mmc1";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +		};
> +
> +		ahb12_rst: reset@01c202c0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202c0 0xc>;
> +		};

This reset controller also resets the timers, it should be initialised
much earlier.

What about having an allwinner,sun8i-h3-bus-reset, and adding it to
the list of compatibles to initialise earlier in
drivers/reset/reset-sunxi.c?

Of course, it would cover the other reset controllers that you have
below.


> +		apb1_rst: reset@01c202d0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d0 0x4>;
> +		};
> +
> +		apb2_rst: reset@01c202d8 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d8 0x4>;
> +		};
> +
> +		timer@01c20c00 {
> +			compatible = "allwinner,sun4i-a10-timer";
> +			reg = <0x01c20c00 0xa0>;
> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&osc24M>;
> +		};
> +
> +		wdt0: watchdog@01c20ca0 {
> +			compatible = "allwinner,sun6i-a31-wdt";
> +			reg = <0x01c20ca0 0x20>;
> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		uart0: serial@01c28000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 16>;
> +			resets = <&apb2_rst 16>;
> +			dmas = <&dma 6>, <&dma 6>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@01c28400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28400 0x400>;
> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 17>;
> +			resets = <&apb2_rst 17>;
> +			dmas = <&dma 7>, <&dma 7>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@01c28800 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28800 0x400>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 18>;
> +			resets = <&apb2_rst 18>;
> +			dmas = <&dma 8>, <&dma 8>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart3: serial@01c28c00 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28c00 0x400>;
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 19>;
> +			resets = <&apb2_rst 19>;
> +			dmas = <&dma 9>, <&dma 9>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		gic: interrupt-controller@01c81000 {
> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> +			reg = <0x01c81000 0x1000>,
> +			      <0x01c82000 0x1000>,
> +			      <0x01c84000 0x2000>,
> +			      <0x01c86000 0x2000>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +		};
> +
> +		rtc: rtc@01f00000 {
> +			compatible = "allwinner,sun6i-a31-rtc";
> +			reg = <0x01f00000 0x54>;
> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +	};
> +};
> -- 
> 2.3.7
> 

Have you tested the architected timers?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Maxime Ripard]

On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
> 
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
>  arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 468 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> new file mode 100644
> index 0000000..53aab95
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -0,0 +1,468 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + *     You should have received a copy of the GNU General Public
> + *     License along with this file; if not, write to the Free
> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> + *     MA 02110-1301 USA

Could you remove that last paragraph?
It generates a checkpatch warning.

> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu at 0 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +
> +		cpu at 1 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <1>;
> +		};
> +
> +		cpu at 2 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <2>;
> +		};
> +
> +		cpu at 3 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <3>;
> +		};
> +	};
> +
> +	memory {
> +		reg = <0x40000000 0x80000000>;
> +	};
> +
> +	clocks {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		osc24M: osc24M_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <24000000>;
> +			clock-output-names = "osc24M";
> +		};
> +
> +		osc32k: osc32k_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <32768>;
> +			clock-output-names = "osc32k";
> +		};
> +
> +		pll1: clk at 01c20000 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-a23-pll1-clk";
> +			reg = <0x01c20000 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll1";
> +		};
> +
> +		pll6: clk at 01c20028 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-pll6-clk";
> +			reg = <0x01c20028 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll6", "pll6x2", "pll6d2";
> +		};
> +
> +		pll8: clk at 01c20044 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-pll8-clk";
> +			reg = <0x01c20044 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll8";
> +		};
> +
> +		cpu: cpu_clk at 01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-cpu-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
> +			clock-output-names = "cpu";
> +		};
> +
> +		axi: axi_clk at 01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-axi-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&cpu>;
> +			clock-output-names = "axi";
> +		};
> +
> +		ahb1: ahb1_clk at 01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
> +			clock-output-names = "ahb1";
> +		};
> +
> +		ahb2: ahb2_clk at 01c2005c {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
> +			reg = <0x01c2005c 0x4>;
> +			clocks = <&ahb1>, <&pll6 2>;
> +			clock-output-names = "ahb2";
> +		};
> +
> +		apb1: apb1_clk at 01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb0-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "apb1";
> +		};
> +
> +		apb2: apb2_clk at 01c20058 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb1-clk";
> +			reg = <0x01c20058 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
> +			clock-output-names = "apb2";
> +		};
> +
> +		ahb1_gates: ahb1_gates_clk at 01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
> +			reg = <0x01c20060 0x14>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
> +					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
> +					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
> +					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
> +					"ahb1_otg_ehci0", "ahb1_ehic1",
> +					"ahb1_ehic2", "ahb1_ehic3",
> +					"ahb1_otg_ohci0", "ahb1_ve",
> +					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
> +					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
> +					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
> +					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
> +		};
> +
> +		ahb2_gates: ahb2_gates_clk at 01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
> +			reg = <0x01c20060 0x4>;
> +			clocks = <&ahb2>;
> +			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
> +					"ahb2_ohic2", "ahb2_ohic3";
> +		};
> +
> +		apb1_gates: clk at 01c20068 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
> +			reg = <0x01c20068 0x4>;
> +			clocks = <&apb1>;
> +			clock-output-names = "apb1_codec", "apb1_spdif",
> +					"apb1_pio", "apb1_ths", "apb1_i2s0",
> +					"apb1_i2s1", "apb1_i2s2";
> +		};
> +
> +		apb2_gates: clk at 01c2006c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
> +			reg = <0x01c2006c 0x4>;
> +			clocks = <&apb2>;
> +			clock-output-names = "apb2_i2c0", "apb2_i2c1",
> +					"apb2_i2c2", "apb2_uart0",
> +					"apb2_uart1", "apb2_uart2",
> +					"apb2_uart3", "apb2_sim";

I'd prefer if the clocks on a new line were right-aligned (like you
did for the mmc clocks just below).

> +		};
> +
> +		mmc0_clk: clk at 01c20088 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20088 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc0",
> +					     "mmc0_output",
> +					     "mmc0_sample";
> +		};
> +
> +		mmc1_clk: clk at 01c2008c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c2008c 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc1",
> +					     "mmc1_output",
> +					     "mmc1_sample";
> +		};
> +
> +		mmc2_clk: clk at 01c20090 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20090 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc2",
> +					     "mmc2_output",
> +					     "mmc2_sample";
> +		};
> +	};
> +
> +	soc at 01c00000 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		dma: dma-controller at 01c02000 {
> +			compatible = "allwinner,sun8i-h3-dma";
> +			reg = <0x01c02000 0x1000>;
> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ahb1_gates 6>;
> +			resets = <&ahb12_rst 6>;
> +			#dma-cells = <1>;
> +		};
> +
> +		mmc0: mmc at 01c0f000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c0f000 0x1000>;
> +			clocks = <&ahb1_gates 8>,
> +				 <&mmc0_clk 0>,
> +				 <&mmc0_clk 1>,
> +				 <&mmc0_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 8>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		mmc1: mmc at 01c10000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c10000 0x1000>;
> +			clocks = <&ahb1_gates 9>,
> +				 <&mmc1_clk 0>,
> +				 <&mmc1_clk 1>,
> +				 <&mmc1_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 9>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		mmc2: mmc at 01c11000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c11000 0x1000>;
> +			clocks = <&ahb1_gates 10>,
> +				 <&mmc2_clk 0>,
> +				 <&mmc2_clk 1>,
> +				 <&mmc2_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 10>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		pio: pinctrl at 01c20800 {
> +			compatible = "allwinner,sun8i-h3-pinctrl";
> +			reg = <0x01c20800 0x400>;
> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&apb1_gates 5>;
> +			gpio-controller;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			#size-cells = <0>;
> +			#gpio-cells = <3>;
> +
> +			uart0_pins_a: uart0 at 0 {
> +				allwinner,pins = "PA4", "PA5";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_pins_a: mmc0 at 0 {
> +				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";

Could you have spaces between the commas, and wrap the line at 80
chars?

> +				allwinner,function = "mmc0";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_cd_pin: mmc0_cd_pin at 0 {
> +				allwinner,pins = "PF6";
> +				allwinner,function = "gpio_in";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +			};
> +
> +			mmc1_pins_a: mmc1 at 0 {
> +				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
> +				allwinner,function = "mmc1";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +		};
> +
> +		ahb12_rst: reset at 01c202c0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202c0 0xc>;
> +		};

This reset controller also resets the timers, it should be initialised
much earlier.

What about having an allwinner,sun8i-h3-bus-reset, and adding it to
the list of compatibles to initialise earlier in
drivers/reset/reset-sunxi.c?

Of course, it would cover the other reset controllers that you have
below.


> +		apb1_rst: reset at 01c202d0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d0 0x4>;
> +		};
> +
> +		apb2_rst: reset at 01c202d8 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d8 0x4>;
> +		};
> +
> +		timer at 01c20c00 {
> +			compatible = "allwinner,sun4i-a10-timer";
> +			reg = <0x01c20c00 0xa0>;
> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&osc24M>;
> +		};
> +
> +		wdt0: watchdog at 01c20ca0 {
> +			compatible = "allwinner,sun6i-a31-wdt";
> +			reg = <0x01c20ca0 0x20>;
> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		uart0: serial at 01c28000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 16>;
> +			resets = <&apb2_rst 16>;
> +			dmas = <&dma 6>, <&dma 6>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart1: serial at 01c28400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28400 0x400>;
> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 17>;
> +			resets = <&apb2_rst 17>;
> +			dmas = <&dma 7>, <&dma 7>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial at 01c28800 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28800 0x400>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 18>;
> +			resets = <&apb2_rst 18>;
> +			dmas = <&dma 8>, <&dma 8>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart3: serial at 01c28c00 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28c00 0x400>;
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 19>;
> +			resets = <&apb2_rst 19>;
> +			dmas = <&dma 9>, <&dma 9>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		gic: interrupt-controller at 01c81000 {
> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> +			reg = <0x01c81000 0x1000>,
> +			      <0x01c82000 0x1000>,
> +			      <0x01c84000 0x2000>,
> +			      <0x01c86000 0x2000>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +		};
> +
> +		rtc: rtc at 01f00000 {
> +			compatible = "allwinner,sun6i-a31-rtc";
> +			reg = <0x01f00000 0x54>;
> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +	};
> +};
> -- 
> 2.3.7
> 

Have you tested the architected timers?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150506/e98e0c71/attachment-0001.sig>

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 15386 bytes --]

On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
> 
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 468 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> new file mode 100644
> index 0000000..53aab95
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -0,0 +1,468 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + *     You should have received a copy of the GNU General Public
> + *     License along with this file; if not, write to the Free
> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> + *     MA 02110-1301 USA

Could you remove that last paragraph?
It generates a checkpatch warning.

> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu@0 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +
> +		cpu@1 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <1>;
> +		};
> +
> +		cpu@2 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <2>;
> +		};
> +
> +		cpu@3 {
> +			compatible = "arm,cortex-a7";
> +			device_type = "cpu";
> +			reg = <3>;
> +		};
> +	};
> +
> +	memory {
> +		reg = <0x40000000 0x80000000>;
> +	};
> +
> +	clocks {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		osc24M: osc24M_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <24000000>;
> +			clock-output-names = "osc24M";
> +		};
> +
> +		osc32k: osc32k_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <32768>;
> +			clock-output-names = "osc32k";
> +		};
> +
> +		pll1: clk@01c20000 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-a23-pll1-clk";
> +			reg = <0x01c20000 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll1";
> +		};
> +
> +		pll6: clk@01c20028 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-pll6-clk";
> +			reg = <0x01c20028 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll6", "pll6x2", "pll6d2";
> +		};
> +
> +		pll8: clk@01c20044 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-pll8-clk";
> +			reg = <0x01c20044 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll8";
> +		};
> +
> +		cpu: cpu_clk@01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-cpu-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
> +			clock-output-names = "cpu";
> +		};
> +
> +		axi: axi_clk@01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-axi-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&cpu>;
> +			clock-output-names = "axi";
> +		};
> +
> +		ahb1: ahb1_clk@01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
> +			clock-output-names = "ahb1";
> +		};
> +
> +		ahb2: ahb2_clk@01c2005c {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
> +			reg = <0x01c2005c 0x4>;
> +			clocks = <&ahb1>, <&pll6 2>;
> +			clock-output-names = "ahb2";
> +		};
> +
> +		apb1: apb1_clk@01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb0-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "apb1";
> +		};
> +
> +		apb2: apb2_clk@01c20058 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb1-clk";
> +			reg = <0x01c20058 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
> +			clock-output-names = "apb2";
> +		};
> +
> +		ahb1_gates: ahb1_gates_clk@01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
> +			reg = <0x01c20060 0x14>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
> +					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
> +					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
> +					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
> +					"ahb1_otg_ehci0", "ahb1_ehic1",
> +					"ahb1_ehic2", "ahb1_ehic3",
> +					"ahb1_otg_ohci0", "ahb1_ve",
> +					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
> +					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
> +					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
> +					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
> +		};
> +
> +		ahb2_gates: ahb2_gates_clk@01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
> +			reg = <0x01c20060 0x4>;
> +			clocks = <&ahb2>;
> +			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
> +					"ahb2_ohic2", "ahb2_ohic3";
> +		};
> +
> +		apb1_gates: clk@01c20068 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
> +			reg = <0x01c20068 0x4>;
> +			clocks = <&apb1>;
> +			clock-output-names = "apb1_codec", "apb1_spdif",
> +					"apb1_pio", "apb1_ths", "apb1_i2s0",
> +					"apb1_i2s1", "apb1_i2s2";
> +		};
> +
> +		apb2_gates: clk@01c2006c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
> +			reg = <0x01c2006c 0x4>;
> +			clocks = <&apb2>;
> +			clock-output-names = "apb2_i2c0", "apb2_i2c1",
> +					"apb2_i2c2", "apb2_uart0",
> +					"apb2_uart1", "apb2_uart2",
> +					"apb2_uart3", "apb2_sim";

I'd prefer if the clocks on a new line were right-aligned (like you
did for the mmc clocks just below).

> +		};
> +
> +		mmc0_clk: clk@01c20088 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20088 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc0",
> +					     "mmc0_output",
> +					     "mmc0_sample";
> +		};
> +
> +		mmc1_clk: clk@01c2008c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c2008c 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc1",
> +					     "mmc1_output",
> +					     "mmc1_sample";
> +		};
> +
> +		mmc2_clk: clk@01c20090 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20090 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc2",
> +					     "mmc2_output",
> +					     "mmc2_sample";
> +		};
> +	};
> +
> +	soc@01c00000 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		dma: dma-controller@01c02000 {
> +			compatible = "allwinner,sun8i-h3-dma";
> +			reg = <0x01c02000 0x1000>;
> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ahb1_gates 6>;
> +			resets = <&ahb12_rst 6>;
> +			#dma-cells = <1>;
> +		};
> +
> +		mmc0: mmc@01c0f000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c0f000 0x1000>;
> +			clocks = <&ahb1_gates 8>,
> +				 <&mmc0_clk 0>,
> +				 <&mmc0_clk 1>,
> +				 <&mmc0_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 8>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		mmc1: mmc@01c10000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c10000 0x1000>;
> +			clocks = <&ahb1_gates 9>,
> +				 <&mmc1_clk 0>,
> +				 <&mmc1_clk 1>,
> +				 <&mmc1_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 9>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		mmc2: mmc@01c11000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c11000 0x1000>;
> +			clocks = <&ahb1_gates 10>,
> +				 <&mmc2_clk 0>,
> +				 <&mmc2_clk 1>,
> +				 <&mmc2_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb12_rst 10>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +		};
> +
> +		pio: pinctrl@01c20800 {
> +			compatible = "allwinner,sun8i-h3-pinctrl";
> +			reg = <0x01c20800 0x400>;
> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&apb1_gates 5>;
> +			gpio-controller;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			#size-cells = <0>;
> +			#gpio-cells = <3>;
> +
> +			uart0_pins_a: uart0@0 {
> +				allwinner,pins = "PA4", "PA5";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_pins_a: mmc0@0 {
> +				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";

Could you have spaces between the commas, and wrap the line at 80
chars?

> +				allwinner,function = "mmc0";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_cd_pin: mmc0_cd_pin@0 {
> +				allwinner,pins = "PF6";
> +				allwinner,function = "gpio_in";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +			};
> +
> +			mmc1_pins_a: mmc1@0 {
> +				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
> +				allwinner,function = "mmc1";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +		};
> +
> +		ahb12_rst: reset@01c202c0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202c0 0xc>;
> +		};

This reset controller also resets the timers, it should be initialised
much earlier.

What about having an allwinner,sun8i-h3-bus-reset, and adding it to
the list of compatibles to initialise earlier in
drivers/reset/reset-sunxi.c?

Of course, it would cover the other reset controllers that you have
below.


> +		apb1_rst: reset@01c202d0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d0 0x4>;
> +		};
> +
> +		apb2_rst: reset@01c202d8 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d8 0x4>;
> +		};
> +
> +		timer@01c20c00 {
> +			compatible = "allwinner,sun4i-a10-timer";
> +			reg = <0x01c20c00 0xa0>;
> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&osc24M>;
> +		};
> +
> +		wdt0: watchdog@01c20ca0 {
> +			compatible = "allwinner,sun6i-a31-wdt";
> +			reg = <0x01c20ca0 0x20>;
> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		uart0: serial@01c28000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 16>;
> +			resets = <&apb2_rst 16>;
> +			dmas = <&dma 6>, <&dma 6>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@01c28400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28400 0x400>;
> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 17>;
> +			resets = <&apb2_rst 17>;
> +			dmas = <&dma 7>, <&dma 7>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@01c28800 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28800 0x400>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 18>;
> +			resets = <&apb2_rst 18>;
> +			dmas = <&dma 8>, <&dma 8>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		uart3: serial@01c28c00 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28c00 0x400>;
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&apb2_gates 19>;
> +			resets = <&apb2_rst 19>;
> +			dmas = <&dma 9>, <&dma 9>;
> +			dma-names = "rx", "tx";
> +			status = "disabled";
> +		};
> +
> +		gic: interrupt-controller@01c81000 {
> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> +			reg = <0x01c81000 0x1000>,
> +			      <0x01c82000 0x1000>,
> +			      <0x01c84000 0x2000>,
> +			      <0x01c86000 0x2000>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +		};
> +
> +		rtc: rtc@01f00000 {
> +			compatible = "allwinner,sun6i-a31-rtc";
> +			reg = <0x01f00000 0x54>;
> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +	};
> +};
> -- 
> 2.3.7
> 

Have you tested the architected timers?

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Jens Kuske]

Hi,

On 06/05/15 14:19, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote:
>> The Allwinner H3 is a home entertainment system oriented SoC with
>> four Cortex-A7 cores and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 468 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>> new file mode 100644
>> index 0000000..53aab95
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>> @@ -0,0 +1,468 @@
>> +/*
>> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + *     You should have received a copy of the GNU General Public
>> + *     License along with this file; if not, write to the Free
>> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> + *     MA 02110-1301 USA
> 
> Could you remove that last paragraph?
> It generates a checkpatch warning.

Sure, will be removed. Just copied it from some other sunxi dtsi.

> 
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +	interrupt-parent = <&gic>;
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu@0 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0>;
>> +		};
>> +
>> +		cpu@1 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <1>;
>> +		};
>> +
>> +		cpu@2 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <2>;
>> +		};
>> +
>> +		cpu@3 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <3>;
>> +		};
>> +	};
>> +
>> +	memory {
>> +		reg = <0x40000000 0x80000000>;
>> +	};
>> +
>> +	clocks {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		osc24M: osc24M_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <24000000>;
>> +			clock-output-names = "osc24M";
>> +		};
>> +
>> +		osc32k: osc32k_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <32768>;
>> +			clock-output-names = "osc32k";
>> +		};
>> +
>> +		pll1: clk@01c20000 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-a23-pll1-clk";
>> +			reg = <0x01c20000 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll1";
>> +		};
>> +
>> +		pll6: clk@01c20028 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-pll6-clk";
>> +			reg = <0x01c20028 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll6", "pll6x2", "pll6d2";
>> +		};
>> +
>> +		pll8: clk@01c20044 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-h3-pll8-clk";
>> +			reg = <0x01c20044 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll8";
>> +		};
>> +
>> +		cpu: cpu_clk@01c20050 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-cpu-clk";
>> +			reg = <0x01c20050 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
>> +			clock-output-names = "cpu";
>> +		};
>> +
>> +		axi: axi_clk@01c20050 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-axi-clk";
>> +			reg = <0x01c20050 0x4>;
>> +			clocks = <&cpu>;
>> +			clock-output-names = "axi";
>> +		};
>> +
>> +		ahb1: ahb1_clk@01c20054 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
>> +			reg = <0x01c20054 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
>> +			clock-output-names = "ahb1";
>> +		};
>> +
>> +		ahb2: ahb2_clk@01c2005c {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
>> +			reg = <0x01c2005c 0x4>;
>> +			clocks = <&ahb1>, <&pll6 2>;
>> +			clock-output-names = "ahb2";
>> +		};
>> +
>> +		apb1: apb1_clk@01c20054 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-apb0-clk";
>> +			reg = <0x01c20054 0x4>;
>> +			clocks = <&ahb1>;
>> +			clock-output-names = "apb1";
>> +		};
>> +
>> +		apb2: apb2_clk@01c20058 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-apb1-clk";
>> +			reg = <0x01c20058 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
>> +			clock-output-names = "apb2";
>> +		};
>> +
>> +		ahb1_gates: ahb1_gates_clk@01c20060 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
>> +			reg = <0x01c20060 0x14>;
>> +			clocks = <&ahb1>;
>> +			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
>> +					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
>> +					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
>> +					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
>> +					"ahb1_otg_ehci0", "ahb1_ehic1",
>> +					"ahb1_ehic2", "ahb1_ehic3",
>> +					"ahb1_otg_ohci0", "ahb1_ve",
>> +					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
>> +					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
>> +					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
>> +					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
>> +		};
>> +
>> +		ahb2_gates: ahb2_gates_clk@01c20060 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
>> +			reg = <0x01c20060 0x4>;
>> +			clocks = <&ahb2>;
>> +			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
>> +					"ahb2_ohic2", "ahb2_ohic3";
>> +		};
>> +
>> +		apb1_gates: clk@01c20068 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
>> +			reg = <0x01c20068 0x4>;
>> +			clocks = <&apb1>;
>> +			clock-output-names = "apb1_codec", "apb1_spdif",
>> +					"apb1_pio", "apb1_ths", "apb1_i2s0",
>> +					"apb1_i2s1", "apb1_i2s2";
>> +		};
>> +
>> +		apb2_gates: clk@01c2006c {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
>> +			reg = <0x01c2006c 0x4>;
>> +			clocks = <&apb2>;
>> +			clock-output-names = "apb2_i2c0", "apb2_i2c1",
>> +					"apb2_i2c2", "apb2_uart0",
>> +					"apb2_uart1", "apb2_uart2",
>> +					"apb2_uart3", "apb2_sim";
> 
> I'd prefer if the clocks on a new line were right-aligned (like you
> did for the mmc clocks just below).

Copied again, but yes, I'll fix them. And apb2_sim gets renamed to
apb2_scr as mentioned in the pinctrl thread.

> 
>> +		};
>> +
>> +		mmc0_clk: clk@01c20088 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c20088 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc0",
>> +					     "mmc0_output",
>> +					     "mmc0_sample";
>> +		};
>> +
>> +		mmc1_clk: clk@01c2008c {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c2008c 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc1",
>> +					     "mmc1_output",
>> +					     "mmc1_sample";
>> +		};
>> +
>> +		mmc2_clk: clk@01c20090 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c20090 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc2",
>> +					     "mmc2_output",
>> +					     "mmc2_sample";
>> +		};
>> +	};
>> +
>> +	soc@01c00000 {
>> +		compatible = "simple-bus";
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		dma: dma-controller@01c02000 {
>> +			compatible = "allwinner,sun8i-h3-dma";
>> +			reg = <0x01c02000 0x1000>;
>> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ahb1_gates 6>;
>> +			resets = <&ahb12_rst 6>;
>> +			#dma-cells = <1>;
>> +		};
>> +
>> +		mmc0: mmc@01c0f000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c0f000 0x1000>;
>> +			clocks = <&ahb1_gates 8>,
>> +				 <&mmc0_clk 0>,
>> +				 <&mmc0_clk 1>,
>> +				 <&mmc0_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 8>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mmc1: mmc@01c10000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c10000 0x1000>;
>> +			clocks = <&ahb1_gates 9>,
>> +				 <&mmc1_clk 0>,
>> +				 <&mmc1_clk 1>,
>> +				 <&mmc1_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 9>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mmc2: mmc@01c11000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c11000 0x1000>;
>> +			clocks = <&ahb1_gates 10>,
>> +				 <&mmc2_clk 0>,
>> +				 <&mmc2_clk 1>,
>> +				 <&mmc2_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 10>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		pio: pinctrl@01c20800 {
>> +			compatible = "allwinner,sun8i-h3-pinctrl";
>> +			reg = <0x01c20800 0x400>;
>> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&apb1_gates 5>;
>> +			gpio-controller;
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +			#size-cells = <0>;
>> +			#gpio-cells = <3>;
>> +
>> +			uart0_pins_a: uart0@0 {
>> +				allwinner,pins = "PA4", "PA5";
>> +				allwinner,function = "uart0";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			mmc0_pins_a: mmc0@0 {
>> +				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
> 
> Could you have spaces between the commas, and wrap the line at 80
> chars?

ok
> 
>> +				allwinner,function = "mmc0";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			mmc0_cd_pin: mmc0_cd_pin@0 {
>> +				allwinner,pins = "PF6";
>> +				allwinner,function = "gpio_in";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> +			};
>> +
>> +			mmc1_pins_a: mmc1@0 {
>> +				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
>> +				allwinner,function = "mmc1";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +		};
>> +
>> +		ahb12_rst: reset@01c202c0 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202c0 0xc>;
>> +		};
> 
> This reset controller also resets the timers, it should be initialised
> much earlier.
> 
> What about having an allwinner,sun8i-h3-bus-reset, and adding it to
> the list of compatibles to initialise earlier in
> drivers/reset/reset-sunxi.c?
> 
> Of course, it would cover the other reset controllers that you have
> below.
> 

You mean using a single bus_rst instead of the three?
Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst and
adding a .init_time = sun6i_timer_init to the sun8i machine.

I'm a bit confused here now, because for A23, which is almost
identical, it got removed after your comment:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html

> 
>> +		apb1_rst: reset@01c202d0 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202d0 0x4>;
>> +		};
>> +
>> +		apb2_rst: reset@01c202d8 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202d8 0x4>;
>> +		};
>> +
>> +		timer@01c20c00 {
>> +			compatible = "allwinner,sun4i-a10-timer";
>> +			reg = <0x01c20c00 0xa0>;
>> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&osc24M>;
>> +		};
>> +
>> +		wdt0: watchdog@01c20ca0 {
>> +			compatible = "allwinner,sun6i-a31-wdt";
>> +			reg = <0x01c20ca0 0x20>;
>> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> +		};
>> +
>> +		uart0: serial@01c28000 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28000 0x400>;
>> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 16>;
>> +			resets = <&apb2_rst 16>;
>> +			dmas = <&dma 6>, <&dma 6>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart1: serial@01c28400 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28400 0x400>;
>> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 17>;
>> +			resets = <&apb2_rst 17>;
>> +			dmas = <&dma 7>, <&dma 7>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart2: serial@01c28800 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28800 0x400>;
>> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 18>;
>> +			resets = <&apb2_rst 18>;
>> +			dmas = <&dma 8>, <&dma 8>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart3: serial@01c28c00 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28c00 0x400>;
>> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 19>;
>> +			resets = <&apb2_rst 19>;
>> +			dmas = <&dma 9>, <&dma 9>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		gic: interrupt-controller@01c81000 {
>> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> +			reg = <0x01c81000 0x1000>,
>> +			      <0x01c82000 0x1000>,
>> +			      <0x01c84000 0x2000>,
>> +			      <0x01c86000 0x2000>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> +		};
>> +
>> +		rtc: rtc@01f00000 {
>> +			compatible = "allwinner,sun6i-a31-rtc";
>> +			reg = <0x01f00000 0x54>;
>> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
>> +		};
>> +	};
>> +};
>> -- 
>> 2.3.7
>>
> 
> Have you tested the architected timers?

Not yet, but I'll look into it.

Jens

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Jens Kuske]

Hi,

On 06/05/15 14:19, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote:
>> The Allwinner H3 is a home entertainment system oriented SoC with
>> four Cortex-A7 cores and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>>  arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 468 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>> new file mode 100644
>> index 0000000..53aab95
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>> @@ -0,0 +1,468 @@
>> +/*
>> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + *     You should have received a copy of the GNU General Public
>> + *     License along with this file; if not, write to the Free
>> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> + *     MA 02110-1301 USA
> 
> Could you remove that last paragraph?
> It generates a checkpatch warning.

Sure, will be removed. Just copied it from some other sunxi dtsi.

> 
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +	interrupt-parent = <&gic>;
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu at 0 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0>;
>> +		};
>> +
>> +		cpu at 1 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <1>;
>> +		};
>> +
>> +		cpu at 2 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <2>;
>> +		};
>> +
>> +		cpu at 3 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <3>;
>> +		};
>> +	};
>> +
>> +	memory {
>> +		reg = <0x40000000 0x80000000>;
>> +	};
>> +
>> +	clocks {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		osc24M: osc24M_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <24000000>;
>> +			clock-output-names = "osc24M";
>> +		};
>> +
>> +		osc32k: osc32k_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <32768>;
>> +			clock-output-names = "osc32k";
>> +		};
>> +
>> +		pll1: clk at 01c20000 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-a23-pll1-clk";
>> +			reg = <0x01c20000 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll1";
>> +		};
>> +
>> +		pll6: clk at 01c20028 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-pll6-clk";
>> +			reg = <0x01c20028 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll6", "pll6x2", "pll6d2";
>> +		};
>> +
>> +		pll8: clk at 01c20044 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-h3-pll8-clk";
>> +			reg = <0x01c20044 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll8";
>> +		};
>> +
>> +		cpu: cpu_clk at 01c20050 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-cpu-clk";
>> +			reg = <0x01c20050 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
>> +			clock-output-names = "cpu";
>> +		};
>> +
>> +		axi: axi_clk at 01c20050 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-axi-clk";
>> +			reg = <0x01c20050 0x4>;
>> +			clocks = <&cpu>;
>> +			clock-output-names = "axi";
>> +		};
>> +
>> +		ahb1: ahb1_clk at 01c20054 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
>> +			reg = <0x01c20054 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
>> +			clock-output-names = "ahb1";
>> +		};
>> +
>> +		ahb2: ahb2_clk at 01c2005c {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
>> +			reg = <0x01c2005c 0x4>;
>> +			clocks = <&ahb1>, <&pll6 2>;
>> +			clock-output-names = "ahb2";
>> +		};
>> +
>> +		apb1: apb1_clk at 01c20054 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-apb0-clk";
>> +			reg = <0x01c20054 0x4>;
>> +			clocks = <&ahb1>;
>> +			clock-output-names = "apb1";
>> +		};
>> +
>> +		apb2: apb2_clk at 01c20058 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-apb1-clk";
>> +			reg = <0x01c20058 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
>> +			clock-output-names = "apb2";
>> +		};
>> +
>> +		ahb1_gates: ahb1_gates_clk at 01c20060 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
>> +			reg = <0x01c20060 0x14>;
>> +			clocks = <&ahb1>;
>> +			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
>> +					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
>> +					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
>> +					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
>> +					"ahb1_otg_ehci0", "ahb1_ehic1",
>> +					"ahb1_ehic2", "ahb1_ehic3",
>> +					"ahb1_otg_ohci0", "ahb1_ve",
>> +					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
>> +					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
>> +					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
>> +					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
>> +		};
>> +
>> +		ahb2_gates: ahb2_gates_clk at 01c20060 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
>> +			reg = <0x01c20060 0x4>;
>> +			clocks = <&ahb2>;
>> +			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
>> +					"ahb2_ohic2", "ahb2_ohic3";
>> +		};
>> +
>> +		apb1_gates: clk at 01c20068 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
>> +			reg = <0x01c20068 0x4>;
>> +			clocks = <&apb1>;
>> +			clock-output-names = "apb1_codec", "apb1_spdif",
>> +					"apb1_pio", "apb1_ths", "apb1_i2s0",
>> +					"apb1_i2s1", "apb1_i2s2";
>> +		};
>> +
>> +		apb2_gates: clk at 01c2006c {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
>> +			reg = <0x01c2006c 0x4>;
>> +			clocks = <&apb2>;
>> +			clock-output-names = "apb2_i2c0", "apb2_i2c1",
>> +					"apb2_i2c2", "apb2_uart0",
>> +					"apb2_uart1", "apb2_uart2",
>> +					"apb2_uart3", "apb2_sim";
> 
> I'd prefer if the clocks on a new line were right-aligned (like you
> did for the mmc clocks just below).

Copied again, but yes, I'll fix them. And apb2_sim gets renamed to
apb2_scr as mentioned in the pinctrl thread.

> 
>> +		};
>> +
>> +		mmc0_clk: clk at 01c20088 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c20088 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc0",
>> +					     "mmc0_output",
>> +					     "mmc0_sample";
>> +		};
>> +
>> +		mmc1_clk: clk at 01c2008c {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c2008c 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc1",
>> +					     "mmc1_output",
>> +					     "mmc1_sample";
>> +		};
>> +
>> +		mmc2_clk: clk at 01c20090 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c20090 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc2",
>> +					     "mmc2_output",
>> +					     "mmc2_sample";
>> +		};
>> +	};
>> +
>> +	soc at 01c00000 {
>> +		compatible = "simple-bus";
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		dma: dma-controller at 01c02000 {
>> +			compatible = "allwinner,sun8i-h3-dma";
>> +			reg = <0x01c02000 0x1000>;
>> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ahb1_gates 6>;
>> +			resets = <&ahb12_rst 6>;
>> +			#dma-cells = <1>;
>> +		};
>> +
>> +		mmc0: mmc at 01c0f000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c0f000 0x1000>;
>> +			clocks = <&ahb1_gates 8>,
>> +				 <&mmc0_clk 0>,
>> +				 <&mmc0_clk 1>,
>> +				 <&mmc0_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 8>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mmc1: mmc at 01c10000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c10000 0x1000>;
>> +			clocks = <&ahb1_gates 9>,
>> +				 <&mmc1_clk 0>,
>> +				 <&mmc1_clk 1>,
>> +				 <&mmc1_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 9>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mmc2: mmc at 01c11000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c11000 0x1000>;
>> +			clocks = <&ahb1_gates 10>,
>> +				 <&mmc2_clk 0>,
>> +				 <&mmc2_clk 1>,
>> +				 <&mmc2_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 10>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		pio: pinctrl at 01c20800 {
>> +			compatible = "allwinner,sun8i-h3-pinctrl";
>> +			reg = <0x01c20800 0x400>;
>> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&apb1_gates 5>;
>> +			gpio-controller;
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +			#size-cells = <0>;
>> +			#gpio-cells = <3>;
>> +
>> +			uart0_pins_a: uart0 at 0 {
>> +				allwinner,pins = "PA4", "PA5";
>> +				allwinner,function = "uart0";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			mmc0_pins_a: mmc0 at 0 {
>> +				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
> 
> Could you have spaces between the commas, and wrap the line at 80
> chars?

ok
> 
>> +				allwinner,function = "mmc0";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			mmc0_cd_pin: mmc0_cd_pin at 0 {
>> +				allwinner,pins = "PF6";
>> +				allwinner,function = "gpio_in";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> +			};
>> +
>> +			mmc1_pins_a: mmc1 at 0 {
>> +				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
>> +				allwinner,function = "mmc1";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +		};
>> +
>> +		ahb12_rst: reset at 01c202c0 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202c0 0xc>;
>> +		};
> 
> This reset controller also resets the timers, it should be initialised
> much earlier.
> 
> What about having an allwinner,sun8i-h3-bus-reset, and adding it to
> the list of compatibles to initialise earlier in
> drivers/reset/reset-sunxi.c?
> 
> Of course, it would cover the other reset controllers that you have
> below.
> 

You mean using a single bus_rst instead of the three?
Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst and
adding a .init_time = sun6i_timer_init to the sun8i machine.

I'm a bit confused here now, because for A23, which is almost
identical, it got removed after your comment:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html

> 
>> +		apb1_rst: reset at 01c202d0 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202d0 0x4>;
>> +		};
>> +
>> +		apb2_rst: reset at 01c202d8 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202d8 0x4>;
>> +		};
>> +
>> +		timer at 01c20c00 {
>> +			compatible = "allwinner,sun4i-a10-timer";
>> +			reg = <0x01c20c00 0xa0>;
>> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&osc24M>;
>> +		};
>> +
>> +		wdt0: watchdog at 01c20ca0 {
>> +			compatible = "allwinner,sun6i-a31-wdt";
>> +			reg = <0x01c20ca0 0x20>;
>> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> +		};
>> +
>> +		uart0: serial at 01c28000 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28000 0x400>;
>> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 16>;
>> +			resets = <&apb2_rst 16>;
>> +			dmas = <&dma 6>, <&dma 6>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart1: serial at 01c28400 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28400 0x400>;
>> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 17>;
>> +			resets = <&apb2_rst 17>;
>> +			dmas = <&dma 7>, <&dma 7>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart2: serial at 01c28800 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28800 0x400>;
>> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 18>;
>> +			resets = <&apb2_rst 18>;
>> +			dmas = <&dma 8>, <&dma 8>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart3: serial at 01c28c00 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28c00 0x400>;
>> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 19>;
>> +			resets = <&apb2_rst 19>;
>> +			dmas = <&dma 9>, <&dma 9>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		gic: interrupt-controller at 01c81000 {
>> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> +			reg = <0x01c81000 0x1000>,
>> +			      <0x01c82000 0x1000>,
>> +			      <0x01c84000 0x2000>,
>> +			      <0x01c86000 0x2000>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> +		};
>> +
>> +		rtc: rtc at 01f00000 {
>> +			compatible = "allwinner,sun6i-a31-rtc";
>> +			reg = <0x01f00000 0x54>;
>> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
>> +		};
>> +	};
>> +};
>> -- 
>> 2.3.7
>>
> 
> Have you tested the architected timers?

Not yet, but I'll look into it.

Jens

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Jens Kuske]

Hi,

On 06/05/15 14:19, Maxime Ripard wrote:
> On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote:
>> The Allwinner H3 is a home entertainment system oriented SoC with
>> four Cortex-A7 cores and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/sun8i-h3.dtsi | 468 ++++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 468 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>> new file mode 100644
>> index 0000000..53aab95
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>> @@ -0,0 +1,468 @@
>> +/*
>> + * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + *     You should have received a copy of the GNU General Public
>> + *     License along with this file; if not, write to the Free
>> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> + *     MA 02110-1301 USA
> 
> Could you remove that last paragraph?
> It generates a checkpatch warning.

Sure, will be removed. Just copied it from some other sunxi dtsi.

> 
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +	interrupt-parent = <&gic>;
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu@0 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <0>;
>> +		};
>> +
>> +		cpu@1 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <1>;
>> +		};
>> +
>> +		cpu@2 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <2>;
>> +		};
>> +
>> +		cpu@3 {
>> +			compatible = "arm,cortex-a7";
>> +			device_type = "cpu";
>> +			reg = <3>;
>> +		};
>> +	};
>> +
>> +	memory {
>> +		reg = <0x40000000 0x80000000>;
>> +	};
>> +
>> +	clocks {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		osc24M: osc24M_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <24000000>;
>> +			clock-output-names = "osc24M";
>> +		};
>> +
>> +		osc32k: osc32k_clk {
>> +			#clock-cells = <0>;
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <32768>;
>> +			clock-output-names = "osc32k";
>> +		};
>> +
>> +		pll1: clk@01c20000 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-a23-pll1-clk";
>> +			reg = <0x01c20000 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll1";
>> +		};
>> +
>> +		pll6: clk@01c20028 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-pll6-clk";
>> +			reg = <0x01c20028 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll6", "pll6x2", "pll6d2";
>> +		};
>> +
>> +		pll8: clk@01c20044 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-h3-pll8-clk";
>> +			reg = <0x01c20044 0x4>;
>> +			clocks = <&osc24M>;
>> +			clock-output-names = "pll8";
>> +		};
>> +
>> +		cpu: cpu_clk@01c20050 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-cpu-clk";
>> +			reg = <0x01c20050 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
>> +			clock-output-names = "cpu";
>> +		};
>> +
>> +		axi: axi_clk@01c20050 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-axi-clk";
>> +			reg = <0x01c20050 0x4>;
>> +			clocks = <&cpu>;
>> +			clock-output-names = "axi";
>> +		};
>> +
>> +		ahb1: ahb1_clk@01c20054 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
>> +			reg = <0x01c20054 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
>> +			clock-output-names = "ahb1";
>> +		};
>> +
>> +		ahb2: ahb2_clk@01c2005c {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
>> +			reg = <0x01c2005c 0x4>;
>> +			clocks = <&ahb1>, <&pll6 2>;
>> +			clock-output-names = "ahb2";
>> +		};
>> +
>> +		apb1: apb1_clk@01c20054 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-apb0-clk";
>> +			reg = <0x01c20054 0x4>;
>> +			clocks = <&ahb1>;
>> +			clock-output-names = "apb1";
>> +		};
>> +
>> +		apb2: apb2_clk@01c20058 {
>> +			#clock-cells = <0>;
>> +			compatible = "allwinner,sun4i-a10-apb1-clk";
>> +			reg = <0x01c20058 0x4>;
>> +			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
>> +			clock-output-names = "apb2";
>> +		};
>> +
>> +		ahb1_gates: ahb1_gates_clk@01c20060 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
>> +			reg = <0x01c20060 0x14>;
>> +			clocks = <&ahb1>;
>> +			clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
>> +					"ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
>> +					"ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
>> +					"ahb1_spi0", "ahb1_spi1", "ahb1_otg",
>> +					"ahb1_otg_ehci0", "ahb1_ehic1",
>> +					"ahb1_ehic2", "ahb1_ehic3",
>> +					"ahb1_otg_ohci0", "ahb1_ve",
>> +					"ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
>> +					"ahb1_csi", "ahb1_tve", "ahb1_hdmi",
>> +					"ahb1_de", "ahb1_gpu", "ahb1_msgbox",
>> +					"ahb1_spinlock", "ahb1_ephy", "ahb1_dbg";
>> +		};
>> +
>> +		ahb2_gates: ahb2_gates_clk@01c20060 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
>> +			reg = <0x01c20060 0x4>;
>> +			clocks = <&ahb2>;
>> +			clock-output-names = "ahb2_gmac", "ahb2_ohic1",
>> +					"ahb2_ohic2", "ahb2_ohic3";
>> +		};
>> +
>> +		apb1_gates: clk@01c20068 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-apb1-gates-clk";
>> +			reg = <0x01c20068 0x4>;
>> +			clocks = <&apb1>;
>> +			clock-output-names = "apb1_codec", "apb1_spdif",
>> +					"apb1_pio", "apb1_ths", "apb1_i2s0",
>> +					"apb1_i2s1", "apb1_i2s2";
>> +		};
>> +
>> +		apb2_gates: clk@01c2006c {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun8i-h3-apb2-gates-clk";
>> +			reg = <0x01c2006c 0x4>;
>> +			clocks = <&apb2>;
>> +			clock-output-names = "apb2_i2c0", "apb2_i2c1",
>> +					"apb2_i2c2", "apb2_uart0",
>> +					"apb2_uart1", "apb2_uart2",
>> +					"apb2_uart3", "apb2_sim";
> 
> I'd prefer if the clocks on a new line were right-aligned (like you
> did for the mmc clocks just below).

Copied again, but yes, I'll fix them. And apb2_sim gets renamed to
apb2_scr as mentioned in the pinctrl thread.

> 
>> +		};
>> +
>> +		mmc0_clk: clk@01c20088 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c20088 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc0",
>> +					     "mmc0_output",
>> +					     "mmc0_sample";
>> +		};
>> +
>> +		mmc1_clk: clk@01c2008c {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c2008c 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc1",
>> +					     "mmc1_output",
>> +					     "mmc1_sample";
>> +		};
>> +
>> +		mmc2_clk: clk@01c20090 {
>> +			#clock-cells = <1>;
>> +			compatible = "allwinner,sun4i-a10-mmc-clk";
>> +			reg = <0x01c20090 0x4>;
>> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> +			clock-output-names = "mmc2",
>> +					     "mmc2_output",
>> +					     "mmc2_sample";
>> +		};
>> +	};
>> +
>> +	soc@01c00000 {
>> +		compatible = "simple-bus";
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		dma: dma-controller@01c02000 {
>> +			compatible = "allwinner,sun8i-h3-dma";
>> +			reg = <0x01c02000 0x1000>;
>> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ahb1_gates 6>;
>> +			resets = <&ahb12_rst 6>;
>> +			#dma-cells = <1>;
>> +		};
>> +
>> +		mmc0: mmc@01c0f000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c0f000 0x1000>;
>> +			clocks = <&ahb1_gates 8>,
>> +				 <&mmc0_clk 0>,
>> +				 <&mmc0_clk 1>,
>> +				 <&mmc0_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 8>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mmc1: mmc@01c10000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c10000 0x1000>;
>> +			clocks = <&ahb1_gates 9>,
>> +				 <&mmc1_clk 0>,
>> +				 <&mmc1_clk 1>,
>> +				 <&mmc1_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 9>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mmc2: mmc@01c11000 {
>> +			compatible = "allwinner,sun5i-a13-mmc";
>> +			reg = <0x01c11000 0x1000>;
>> +			clocks = <&ahb1_gates 10>,
>> +				 <&mmc2_clk 0>,
>> +				 <&mmc2_clk 1>,
>> +				 <&mmc2_clk 2>;
>> +			clock-names = "ahb",
>> +				      "mmc",
>> +				      "output",
>> +				      "sample";
>> +			resets = <&ahb12_rst 10>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +		};
>> +
>> +		pio: pinctrl@01c20800 {
>> +			compatible = "allwinner,sun8i-h3-pinctrl";
>> +			reg = <0x01c20800 0x400>;
>> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&apb1_gates 5>;
>> +			gpio-controller;
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +			#size-cells = <0>;
>> +			#gpio-cells = <3>;
>> +
>> +			uart0_pins_a: uart0@0 {
>> +				allwinner,pins = "PA4", "PA5";
>> +				allwinner,function = "uart0";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			mmc0_pins_a: mmc0@0 {
>> +				allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
> 
> Could you have spaces between the commas, and wrap the line at 80
> chars?

ok
> 
>> +				allwinner,function = "mmc0";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +
>> +			mmc0_cd_pin: mmc0_cd_pin@0 {
>> +				allwinner,pins = "PF6";
>> +				allwinner,function = "gpio_in";
>> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> +			};
>> +
>> +			mmc1_pins_a: mmc1@0 {
>> +				allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
>> +				allwinner,function = "mmc1";
>> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +			};
>> +		};
>> +
>> +		ahb12_rst: reset@01c202c0 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202c0 0xc>;
>> +		};
> 
> This reset controller also resets the timers, it should be initialised
> much earlier.
> 
> What about having an allwinner,sun8i-h3-bus-reset, and adding it to
> the list of compatibles to initialise earlier in
> drivers/reset/reset-sunxi.c?
> 
> Of course, it would cover the other reset controllers that you have
> below.
> 

You mean using a single bus_rst instead of the three?
Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst and
adding a .init_time = sun6i_timer_init to the sun8i machine.

I'm a bit confused here now, because for A23, which is almost
identical, it got removed after your comment:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html

> 
>> +		apb1_rst: reset@01c202d0 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202d0 0x4>;
>> +		};
>> +
>> +		apb2_rst: reset@01c202d8 {
>> +			#reset-cells = <1>;
>> +			compatible = "allwinner,sun6i-a31-clock-reset";
>> +			reg = <0x01c202d8 0x4>;
>> +		};
>> +
>> +		timer@01c20c00 {
>> +			compatible = "allwinner,sun4i-a10-timer";
>> +			reg = <0x01c20c00 0xa0>;
>> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&osc24M>;
>> +		};
>> +
>> +		wdt0: watchdog@01c20ca0 {
>> +			compatible = "allwinner,sun6i-a31-wdt";
>> +			reg = <0x01c20ca0 0x20>;
>> +			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
>> +		};
>> +
>> +		uart0: serial@01c28000 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28000 0x400>;
>> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 16>;
>> +			resets = <&apb2_rst 16>;
>> +			dmas = <&dma 6>, <&dma 6>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart1: serial@01c28400 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28400 0x400>;
>> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 17>;
>> +			resets = <&apb2_rst 17>;
>> +			dmas = <&dma 7>, <&dma 7>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart2: serial@01c28800 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28800 0x400>;
>> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 18>;
>> +			resets = <&apb2_rst 18>;
>> +			dmas = <&dma 8>, <&dma 8>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		uart3: serial@01c28c00 {
>> +			compatible = "snps,dw-apb-uart";
>> +			reg = <0x01c28c00 0x400>;
>> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> +			reg-shift = <2>;
>> +			reg-io-width = <4>;
>> +			clocks = <&apb2_gates 19>;
>> +			resets = <&apb2_rst 19>;
>> +			dmas = <&dma 9>, <&dma 9>;
>> +			dma-names = "rx", "tx";
>> +			status = "disabled";
>> +		};
>> +
>> +		gic: interrupt-controller@01c81000 {
>> +			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> +			reg = <0x01c81000 0x1000>,
>> +			      <0x01c82000 0x1000>,
>> +			      <0x01c84000 0x2000>,
>> +			      <0x01c86000 0x2000>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> +		};
>> +
>> +		rtc: rtc@01f00000 {
>> +			compatible = "allwinner,sun6i-a31-rtc";
>> +			reg = <0x01f00000 0x54>;
>> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
>> +		};
>> +	};
>> +};
>> -- 
>> 2.3.7
>>
> 
> Have you tested the architected timers?

Not yet, but I'll look into it.

Jens

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2134 bytes --]

On Wed, May 06, 2015 at 10:47:33PM +0200, Jens Kuske wrote:
> >> + *     You should have received a copy of the GNU General Public
> >> + *     License along with this file; if not, write to the Free
> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> >> + *     MA 02110-1301 USA
> > 
> > Could you remove that last paragraph?
> > It generates a checkpatch warning.
> 
> Sure, will be removed. Just copied it from some other sunxi dtsi.

Yeah, I know, I'm even the one that introduced this in the first place
:)

I sent a patch earlier this week to remove it from the other DT.

> >> +		ahb12_rst: reset@01c202c0 {
> >> +			#reset-cells = <1>;
> >> +			compatible = "allwinner,sun6i-a31-clock-reset";
> >> +			reg = <0x01c202c0 0xc>;
> >> +		};
> > 
> > This reset controller also resets the timers, it should be initialised
> > much earlier.
> > 
> > What about having an allwinner,sun8i-h3-bus-reset, and adding it to
> > the list of compatibles to initialise earlier in
> > drivers/reset/reset-sunxi.c?
> > 
> > Of course, it would cover the other reset controllers that you have
> > below.
> > 
> 
> You mean using a single bus_rst instead of the three?

Yes.

> Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst

Strictly speaking, they do not control the same set of devices. I'd
prefer to have a different compatible in case we need to setup a
particular behaviour on a given SoC (for example, force out of reset a
particular device, even if no driver is actually using it), without
impacting the other.

> and adding a .init_time = sun6i_timer_init to the sun8i machine.

But we will need to do that yes.

> I'm a bit confused here now, because for A23, which is almost
> identical, it got removed after your comment:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html

Hmmmm, I think I somehow overlooked the fact that the timer was there,
even though Chen-Yu said it. My bad :/

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Maxime Ripard]

On Wed, May 06, 2015 at 10:47:33PM +0200, Jens Kuske wrote:
> >> + *     You should have received a copy of the GNU General Public
> >> + *     License along with this file; if not, write to the Free
> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> >> + *     MA 02110-1301 USA
> > 
> > Could you remove that last paragraph?
> > It generates a checkpatch warning.
> 
> Sure, will be removed. Just copied it from some other sunxi dtsi.

Yeah, I know, I'm even the one that introduced this in the first place
:)

I sent a patch earlier this week to remove it from the other DT.

> >> +		ahb12_rst: reset at 01c202c0 {
> >> +			#reset-cells = <1>;
> >> +			compatible = "allwinner,sun6i-a31-clock-reset";
> >> +			reg = <0x01c202c0 0xc>;
> >> +		};
> > 
> > This reset controller also resets the timers, it should be initialised
> > much earlier.
> > 
> > What about having an allwinner,sun8i-h3-bus-reset, and adding it to
> > the list of compatibles to initialise earlier in
> > drivers/reset/reset-sunxi.c?
> > 
> > Of course, it would cover the other reset controllers that you have
> > below.
> > 
> 
> You mean using a single bus_rst instead of the three?

Yes.

> Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst

Strictly speaking, they do not control the same set of devices. I'd
prefer to have a different compatible in case we need to setup a
particular behaviour on a given SoC (for example, force out of reset a
particular device, even if no driver is actually using it), without
impacting the other.

> and adding a .init_time = sun6i_timer_init to the sun8i machine.

But we will need to do that yes.

> I'm a bit confused here now, because for A23, which is almost
> identical, it got removed after your comment:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html

Hmmmm, I think I somehow overlooked the fact that the timer was there,
even though Chen-Yu said it. My bad :/

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150509/9181af3e/attachment.sig>

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2071 bytes --]

On Wed, May 06, 2015 at 10:47:33PM +0200, Jens Kuske wrote:
> >> + *     You should have received a copy of the GNU General Public
> >> + *     License along with this file; if not, write to the Free
> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> >> + *     MA 02110-1301 USA
> > 
> > Could you remove that last paragraph?
> > It generates a checkpatch warning.
> 
> Sure, will be removed. Just copied it from some other sunxi dtsi.

Yeah, I know, I'm even the one that introduced this in the first place
:)

I sent a patch earlier this week to remove it from the other DT.

> >> +		ahb12_rst: reset@01c202c0 {
> >> +			#reset-cells = <1>;
> >> +			compatible = "allwinner,sun6i-a31-clock-reset";
> >> +			reg = <0x01c202c0 0xc>;
> >> +		};
> > 
> > This reset controller also resets the timers, it should be initialised
> > much earlier.
> > 
> > What about having an allwinner,sun8i-h3-bus-reset, and adding it to
> > the list of compatibles to initialise earlier in
> > drivers/reset/reset-sunxi.c?
> > 
> > Of course, it would cover the other reset controllers that you have
> > below.
> > 
> 
> You mean using a single bus_rst instead of the three?

Yes.

> Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst

Strictly speaking, they do not control the same set of devices. I'd
prefer to have a different compatible in case we need to setup a
particular behaviour on a given SoC (for example, force out of reset a
particular device, even if no driver is actually using it), without
impacting the other.

> and adding a .init_time = sun6i_timer_init to the sun8i machine.

But we will need to do that yes.

> I'm a bit confused here now, because for A23, which is almost
> identical, it got removed after your comment:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html

Hmmmm, I think I somehow overlooked the fact that the timer was there,
even though Chen-Yu said it. My bad :/

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Chen-Yu Tsai]

On Sat, May 9, 2015 at 7:44 PM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> On Wed, May 06, 2015 at 10:47:33PM +0200, Jens Kuske wrote:
>> >> + *     You should have received a copy of the GNU General Public
>> >> + *     License along with this file; if not, write to the Free
>> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> >> + *     MA 02110-1301 USA
>> >
>> > Could you remove that last paragraph?
>> > It generates a checkpatch warning.
>>
>> Sure, will be removed. Just copied it from some other sunxi dtsi.
>
> Yeah, I know, I'm even the one that introduced this in the first place
> :)
>
> I sent a patch earlier this week to remove it from the other DT.
>
>> >> +          ahb12_rst: reset@01c202c0 {
>> >> +                  #reset-cells = <1>;
>> >> +                  compatible = "allwinner,sun6i-a31-clock-reset";
>> >> +                  reg = <0x01c202c0 0xc>;
>> >> +          };
>> >
>> > This reset controller also resets the timers, it should be initialised
>> > much earlier.
>> >
>> > What about having an allwinner,sun8i-h3-bus-reset, and adding it to
>> > the list of compatibles to initialise earlier in
>> > drivers/reset/reset-sunxi.c?
>> >
>> > Of course, it would cover the other reset controllers that you have
>> > below.
>> >
>>
>> You mean using a single bus_rst instead of the three?
>
> Yes.
>
>> Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst
>
> Strictly speaking, they do not control the same set of devices. I'd
> prefer to have a different compatible in case we need to setup a
> particular behaviour on a given SoC (for example, force out of reset a
> particular device, even if no driver is actually using it), without
> impacting the other.
>
>> and adding a .init_time = sun6i_timer_init to the sun8i machine.
>
> But we will need to do that yes.
>
>> I'm a bit confused here now, because for A23, which is almost
>> identical, it got removed after your comment:
>> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html
>
> Hmmmm, I think I somehow overlooked the fact that the timer was there,
> even though Chen-Yu said it. My bad :/

On the A23, the high speed timer block only has 1 timer. The sun5i-hrtimer
driver requires 2, and turns out we weren't using them anyway, so I just
dropped sun5i-hrtimer support on A23.

If the other sun8i SoCs have 2 or more timers, feel free to support them.

ChenYu

[PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Chen-Yu Tsai]

On Sat, May 9, 2015 at 7:44 PM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> On Wed, May 06, 2015 at 10:47:33PM +0200, Jens Kuske wrote:
>> >> + *     You should have received a copy of the GNU General Public
>> >> + *     License along with this file; if not, write to the Free
>> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> >> + *     MA 02110-1301 USA
>> >
>> > Could you remove that last paragraph?
>> > It generates a checkpatch warning.
>>
>> Sure, will be removed. Just copied it from some other sunxi dtsi.
>
> Yeah, I know, I'm even the one that introduced this in the first place
> :)
>
> I sent a patch earlier this week to remove it from the other DT.
>
>> >> +          ahb12_rst: reset at 01c202c0 {
>> >> +                  #reset-cells = <1>;
>> >> +                  compatible = "allwinner,sun6i-a31-clock-reset";
>> >> +                  reg = <0x01c202c0 0xc>;
>> >> +          };
>> >
>> > This reset controller also resets the timers, it should be initialised
>> > much earlier.
>> >
>> > What about having an allwinner,sun8i-h3-bus-reset, and adding it to
>> > the list of compatibles to initialise earlier in
>> > drivers/reset/reset-sunxi.c?
>> >
>> > Of course, it would cover the other reset controllers that you have
>> > below.
>> >
>>
>> You mean using a single bus_rst instead of the three?
>
> Yes.
>
>> Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst
>
> Strictly speaking, they do not control the same set of devices. I'd
> prefer to have a different compatible in case we need to setup a
> particular behaviour on a given SoC (for example, force out of reset a
> particular device, even if no driver is actually using it), without
> impacting the other.
>
>> and adding a .init_time = sun6i_timer_init to the sun8i machine.
>
> But we will need to do that yes.
>
>> I'm a bit confused here now, because for A23, which is almost
>> identical, it got removed after your comment:
>> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html
>
> Hmmmm, I think I somehow overlooked the fact that the timer was there,
> even though Chen-Yu said it. My bad :/

On the A23, the high speed timer block only has 1 timer. The sun5i-hrtimer
driver requires 2, and turns out we weren't using them anyway, so I just
dropped sun5i-hrtimer support on A23.

If the other sun8i SoCs have 2 or more timers, feel free to support them.

ChenYu

Re: [PATCH 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI

[Chen-Yu Tsai]

On Sat, May 9, 2015 at 7:44 PM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> On Wed, May 06, 2015 at 10:47:33PM +0200, Jens Kuske wrote:
>> >> + *     You should have received a copy of the GNU General Public
>> >> + *     License along with this file; if not, write to the Free
>> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> >> + *     MA 02110-1301 USA
>> >
>> > Could you remove that last paragraph?
>> > It generates a checkpatch warning.
>>
>> Sure, will be removed. Just copied it from some other sunxi dtsi.
>
> Yeah, I know, I'm even the one that introduced this in the first place
> :)
>
> I sent a patch earlier this week to remove it from the other DT.
>
>> >> +          ahb12_rst: reset@01c202c0 {
>> >> +                  #reset-cells = <1>;
>> >> +                  compatible = "allwinner,sun6i-a31-clock-reset";
>> >> +                  reg = <0x01c202c0 0xc>;
>> >> +          };
>> >
>> > This reset controller also resets the timers, it should be initialised
>> > much earlier.
>> >
>> > What about having an allwinner,sun8i-h3-bus-reset, and adding it to
>> > the list of compatibles to initialise earlier in
>> > drivers/reset/reset-sunxi.c?
>> >
>> > Of course, it would cover the other reset controllers that you have
>> > below.
>> >
>>
>> You mean using a single bus_rst instead of the three?
>
> Yes.
>
>> Or, why not using allwinner,sun6i-a31-ahb1-reset for ahb12_rst
>
> Strictly speaking, they do not control the same set of devices. I'd
> prefer to have a different compatible in case we need to setup a
> particular behaviour on a given SoC (for example, force out of reset a
> particular device, even if no driver is actually using it), without
> impacting the other.
>
>> and adding a .init_time = sun6i_timer_init to the sun8i machine.
>
> But we will need to do that yes.
>
>> I'm a bit confused here now, because for A23, which is almost
>> identical, it got removed after your comment:
>> http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/265064.html
>
> Hmmmm, I think I somehow overlooked the fact that the timer was there,
> even though Chen-Yu said it. My bad :/

On the A23, the high speed timer block only has 1 timer. The sun5i-hrtimer
driver requires 2, and turns out we weren't using them anyway, so I just
dropped sun5i-hrtimer support on A23.

If the other sun8i SoCs have 2 or more timers, feel free to support them.

ChenYu

[PATCH 6/6] ARM: dts: sun8i: Add Orange Pi Plus support

[Jens Kuske]

The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 82 ++++++++++++++++++++++++++++
 2 files changed, 84 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 83a4e68..149cd82 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -570,7 +570,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-wexler-tab7200.dtb
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..50c8316
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,82 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Xunlong Orange Pi Plus";
+	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
-- 
2.3.7

[PATCH 6/6] ARM: dts: sun8i: Add Orange Pi Plus support

[Jens Kuske]

The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 82 ++++++++++++++++++++++++++++
 2 files changed, 84 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 83a4e68..149cd82 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -570,7 +570,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-wexler-tab7200.dtb
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..50c8316
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,82 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Xunlong Orange Pi Plus";
+	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
-- 
2.3.7

[PATCH 6/6] ARM: dts: sun8i: Add Orange Pi Plus support

[Jens Kuske]

The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.

Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                   |  3 +-
 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 82 ++++++++++++++++++++++++++++
 2 files changed, 84 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 83a4e68..149cd82 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -570,7 +570,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-wexler-tab7200.dtb
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..50c8316
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,82 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Xunlong Orange Pi Plus";
+	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
-- 
2.3.7

Re: [linux-sunxi] [PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[Hans de Goede]

Hi,

On 06-05-15 11:31, Jens Kuske wrote:
> Hi everyone,
>
> This patch series introduces basic kernel support for Allwinner's H3 SoC,
> mainly basic clocks and pinctrl. It also adds interrupts, timers,
> watchdog, RTC, dmaengine, MMC and UARTs, which are mostly compatible to
> those in earlier SoCs like A23 and A31, and can simply be reused.
>
> These patches are based on Maxime's sunxi/for-next branch from
> git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git
>
> Patch 1 adds machine support for the H3.
>
> Patch 2 adds support for the basic clocks. The AHB1/AHB2 split could
> need some discussion.
>
> Patch 3 adds the pin sets for the H3 main PIO.
>
> Patch 4 adds the H3 specific parameters to the sun6i dmaengine driver.
>
> Patch 5 adds the DTSI for the H3.
>
> Patch 6 adds a DT for the Orange Pi Plus SBC, which these patches
> were developed and tested with.

Cool stuff, thanks for your work on this. Do you have any plans to also
add support for the H3 to upstream u-boot ?

Regards,

Hans

[linux-sunxi] [PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[Hans de Goede]

Hi,

On 06-05-15 11:31, Jens Kuske wrote:
> Hi everyone,
>
> This patch series introduces basic kernel support for Allwinner's H3 SoC,
> mainly basic clocks and pinctrl. It also adds interrupts, timers,
> watchdog, RTC, dmaengine, MMC and UARTs, which are mostly compatible to
> those in earlier SoCs like A23 and A31, and can simply be reused.
>
> These patches are based on Maxime's sunxi/for-next branch from
> git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git
>
> Patch 1 adds machine support for the H3.
>
> Patch 2 adds support for the basic clocks. The AHB1/AHB2 split could
> need some discussion.
>
> Patch 3 adds the pin sets for the H3 main PIO.
>
> Patch 4 adds the H3 specific parameters to the sun6i dmaengine driver.
>
> Patch 5 adds the DTSI for the H3.
>
> Patch 6 adds a DT for the Orange Pi Plus SBC, which these patches
> were developed and tested with.

Cool stuff, thanks for your work on this. Do you have any plans to also
add support for the H3 to upstream u-boot ?

Regards,

Hans

Re: [linux-sunxi] [PATCH 0/6] ARM: sunxi: Introduce Allwinner H3 support

[Hans de Goede]

Hi,

On 06-05-15 11:31, Jens Kuske wrote:
> Hi everyone,
>
> This patch series introduces basic kernel support for Allwinner's H3 SoC,
> mainly basic clocks and pinctrl. It also adds interrupts, timers,
> watchdog, RTC, dmaengine, MMC and UARTs, which are mostly compatible to
> those in earlier SoCs like A23 and A31, and can simply be reused.
>
> These patches are based on Maxime's sunxi/for-next branch from
> git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git
>
> Patch 1 adds machine support for the H3.
>
> Patch 2 adds support for the basic clocks. The AHB1/AHB2 split could
> need some discussion.
>
> Patch 3 adds the pin sets for the H3 main PIO.
>
> Patch 4 adds the H3 specific parameters to the sun6i dmaengine driver.
>
> Patch 5 adds the DTSI for the H3.
>
> Patch 6 adds a DT for the Orange Pi Plus SBC, which these patches
> were developed and tested with.

Cool stuff, thanks for your work on this. Do you have any plans to also
add support for the H3 to upstream u-boot ?

Regards,

Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html