[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Imre Kaloz]

This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).

Both boards have:

- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM

Signed-off-by: Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>

---
Changes since v1: added DSA support
---
The only difference between the two boards is the radio configuration
(2x2 vs 3x3), so everything except the leds (to be named properly)
is in the dtsi file. When the wireless driver will be submitted
upstream, the powertables (calibration data) will end up in the board
specific files, tho.
---
 arch/arm/boot/dts/Makefile                      |   2 +
 arch/arm/boot/dts/armada-385-linksys-caiman.dts | 114 ++++++++
 arch/arm/boot/dts/armada-385-linksys-cobra.dts  | 114 ++++++++
 arch/arm/boot/dts/armada-385-linksys.dtsi       | 333 ++++++++++++++++++++++++
 4 files changed, 563 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-385-linksys-caiman.dts
 create mode 100644 arch/arm/boot/dts/armada-385-linksys-cobra.dts
 create mode 100644 arch/arm/boot/dts/armada-385-linksys.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 86217db..0eaea61 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -633,6 +633,8 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \
 	armada-375-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-385-db-ap.dtb \
+	armada-385-linksys-caiman.dtb \
+	armada-385-linksys-cobra.dtb \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
 	armada-388-rd.dtb
diff --git a/arch/arm/boot/dts/armada-385-linksys-caiman.dts b/arch/arm/boot/dts/armada-385-linksys-caiman.dts
new file mode 100644
index 0000000..f3cee91
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys-caiman.dts
@@ -0,0 +1,114 @@
+/*
+ * Device Tree include for the Linksys WRT1200AC (Caiman)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1200AC";
+	compatible = "linksys,caiman", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c@11000 {
+
+				pca9635@68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber@0 {
+						label = "caiman:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white@1 {
+						label = "caiman:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g@2 {
+						label = "caiman:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g@3 {
+						label = "caiman:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2@5 {
+						label = "caiman:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1@6 {
+						label = "caiman:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2@7 {
+						label = "caiman:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white@8 {
+						label = "caiman:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber@9 {
+						label = "caiman:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "caiman:white:power";
+		};
+
+		sata {
+			label = "caiman:white:sata";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-linksys-cobra.dts b/arch/arm/boot/dts/armada-385-linksys-cobra.dts
new file mode 100644
index 0000000..1110718
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys-cobra.dts
@@ -0,0 +1,114 @@
+/*
+ * Device Tree file for the Linksys WRT1900ACv2 (Cobra)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1900ACv2";
+	compatible = "linksys,cobra", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c@11000 {
+
+				pca9635@68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber@0 {
+						label = "cobra:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white@1 {
+						label = "cobra:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g@2 {
+						label = "cobra:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g@3 {
+						label = "cobra:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2@5 {
+						label = "cobra:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1@6 {
+						label = "cobra:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2@7 {
+						label = "cobra:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white@8 {
+						label = "cobra:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber@9 {
+						label = "cobra:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "cobra:white:power";
+		};
+
+		sata {
+			label = "cobra:white:sata";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi
new file mode 100644
index 0000000..b7806f6
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
@@ -0,0 +1,333 @@
+/*
+ * Device Tree include file for Armada 385 based Linksys boards
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-385.dtsi"
+
+/ {
+	model = "Linksys boards based on Armada 385";
+	compatible = "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+
+			spi@10600 {
+				status = "disabled";
+			};
+
+			i2c@11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+
+				tmp421@4c {
+					compatible = "ti,tmp421";
+					reg = <0x4c>;
+				};
+
+				pca9635@68 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "nxp,pca9635";
+					reg = <0x68>;
+				};
+			};
+
+			/* J10: VCC, NC, RX, NC, TX, GND  */
+			serial@12000 {
+				status = "okay";
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet@34000 {
+				status = "okay";
+				phy-mode = "sgmii";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			mdio {
+				status = "okay";
+			};
+
+			sata@a8000 {
+				status = "okay";
+			};
+
+			/* USB part of the eSATA/USB 2.0 port */
+			usb@50000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+				usb-phy = <&usb3_phy>;
+			};
+
+			flash@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition@0 {
+					label = "u-boot";
+					reg = <0x0000000 0x200000>;  /* 2MB */
+					read-only;
+				};
+
+				partition@100000 {
+					label = "u_env";
+					reg = <0x200000 0x40000>;    /* 256KB */
+				};
+
+				partition@140000 {
+					label = "s_env";
+					reg = <0x240000 0x40000>;    /* 256KB */
+				};
+
+				partition@900000 {
+					label = "devinfo";
+					reg = <0x900000 0x100000>;   /* 1MB */
+					read-only;
+				};
+
+				/* kernel1 overlaps with rootfs1 by design */
+				partition@a00000 {
+					label = "kernel1";
+					reg = <0xa00000 0x2800000>;  /* 40MB */
+				};
+
+				partition@1000000 {
+					label = "rootfs1";
+					reg = <0x1000000 0x2200000>;  /* 34MB */
+				};
+
+				/* kernel2 overlaps with rootfs2 by design */
+				partition@3200000 {
+					label = "kernel2";
+					reg = <0x3200000 0x2800000>; /* 40MB */
+				};
+
+				partition@3800000 {
+					label = "rootfs2";
+					reg = <0x3800000 0x2200000>; /* 34MB */
+				};
+
+				/*
+				 * 38MB, last MB is for the BBT, not writable
+				 */
+				partition@5a00000 {
+					label = "syscfg";
+					reg = <0x5a00000 0x2600000>;
+				};
+
+				/*
+				 * Unused area between "s_env" and "devinfo".
+				 * Moved here because otherwise the renumbered
+				 * partitions would break the bootloader
+				 * supplied bootargs
+				 */
+				partition@180000 {
+					label = "unused_area";
+					reg = <0x280000 0x680000>;   /* 6.5MB */
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				/* Marvell 88W8864, 5GHz-only */
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				/* Marvell 88W8864, 2GHz-only */
+				status = "okay";
+			};
+		};
+	};
+
+	usb3_phy: usb3_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_xhci0_vbus>;
+	};
+
+	reg_xhci0_vbus: xhci0-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci0_vbus_pins>;
+		regulator-name = "xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&keys_pin>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+
+		button@2 {
+			label = "Factory Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&power_led_pin &sata_led_pin>;
+		pinctrl-names = "default";
+
+		power {
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		sata {
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	dsa@0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth2>;
+		dsa,mii-bus = <&mdio>;
+
+		switch@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0>;	/* MDIO address 0, switch 0 in tree */
+
+			port@0 {
+				reg = <0>;
+				label = "lan4";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan3";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan2";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan1";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	keys_pin: keys-pin {
+		marvell,pins = "mpp24", "mpp47";
+		marvell,function = "gpio";
+	};
+
+	power_led_pin: power-led-pin {
+		marvell,pins = "mpp55";
+		marvell,function = "gpio";
+	};
+
+	sata_led_pin: sata-led-pin {
+		marvell,pins = "mpp54";
+		marvell,function = "gpio";
+	};
+
+	xhci0_vbus_pins: xhci0-vbus-pins {
+		marvell,pins = "mpp50";
+		marvell,function = "gpio";
+	};
+};
-- 
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Imre Kaloz]

This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).

Both boards have:

- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

---
Changes since v1: added DSA support
---
The only difference between the two boards is the radio configuration
(2x2 vs 3x3), so everything except the leds (to be named properly)
is in the dtsi file. When the wireless driver will be submitted
upstream, the powertables (calibration data) will end up in the board
specific files, tho.
---
 arch/arm/boot/dts/Makefile                      |   2 +
 arch/arm/boot/dts/armada-385-linksys-caiman.dts | 114 ++++++++
 arch/arm/boot/dts/armada-385-linksys-cobra.dts  | 114 ++++++++
 arch/arm/boot/dts/armada-385-linksys.dtsi       | 333 ++++++++++++++++++++++++
 4 files changed, 563 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-385-linksys-caiman.dts
 create mode 100644 arch/arm/boot/dts/armada-385-linksys-cobra.dts
 create mode 100644 arch/arm/boot/dts/armada-385-linksys.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 86217db..0eaea61 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -633,6 +633,8 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \
 	armada-375-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-385-db-ap.dtb \
+	armada-385-linksys-caiman.dtb \
+	armada-385-linksys-cobra.dtb \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
 	armada-388-rd.dtb
diff --git a/arch/arm/boot/dts/armada-385-linksys-caiman.dts b/arch/arm/boot/dts/armada-385-linksys-caiman.dts
new file mode 100644
index 0000000..f3cee91
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys-caiman.dts
@@ -0,0 +1,114 @@
+/*
+ * Device Tree include for the Linksys WRT1200AC (Caiman)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1200AC";
+	compatible = "linksys,caiman", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c at 11000 {
+
+				pca9635 at 68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber at 0 {
+						label = "caiman:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white at 1 {
+						label = "caiman:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g at 2 {
+						label = "caiman:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g at 3 {
+						label = "caiman:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2 at 5 {
+						label = "caiman:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1 at 6 {
+						label = "caiman:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2 at 7 {
+						label = "caiman:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white at 8 {
+						label = "caiman:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber at 9 {
+						label = "caiman:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "caiman:white:power";
+		};
+
+		sata {
+			label = "caiman:white:sata";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-linksys-cobra.dts b/arch/arm/boot/dts/armada-385-linksys-cobra.dts
new file mode 100644
index 0000000..1110718
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys-cobra.dts
@@ -0,0 +1,114 @@
+/*
+ * Device Tree file for the Linksys WRT1900ACv2 (Cobra)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1900ACv2";
+	compatible = "linksys,cobra", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c at 11000 {
+
+				pca9635 at 68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber at 0 {
+						label = "cobra:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white at 1 {
+						label = "cobra:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g at 2 {
+						label = "cobra:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g at 3 {
+						label = "cobra:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2 at 5 {
+						label = "cobra:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1 at 6 {
+						label = "cobra:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2 at 7 {
+						label = "cobra:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white at 8 {
+						label = "cobra:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber at 9 {
+						label = "cobra:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "cobra:white:power";
+		};
+
+		sata {
+			label = "cobra:white:sata";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi
new file mode 100644
index 0000000..b7806f6
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
@@ -0,0 +1,333 @@
+/*
+ * Device Tree include file for Armada 385 based Linksys boards
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-385.dtsi"
+
+/ {
+	model = "Linksys boards based on Armada 385";
+	compatible = "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+
+			spi at 10600 {
+				status = "disabled";
+			};
+
+			i2c at 11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+
+				tmp421 at 4c {
+					compatible = "ti,tmp421";
+					reg = <0x4c>;
+				};
+
+				pca9635 at 68 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "nxp,pca9635";
+					reg = <0x68>;
+				};
+			};
+
+			/* J10: VCC, NC, RX, NC, TX, GND  */
+			serial at 12000 {
+				status = "okay";
+			};
+
+			ethernet at 70000 {
+				status = "okay";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet at 34000 {
+				status = "okay";
+				phy-mode = "sgmii";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			mdio {
+				status = "okay";
+			};
+
+			sata at a8000 {
+				status = "okay";
+			};
+
+			/* USB part of the eSATA/USB 2.0 port */
+			usb at 50000 {
+				status = "okay";
+			};
+
+			usb3 at f8000 {
+				status = "okay";
+				usb-phy = <&usb3_phy>;
+			};
+
+			flash at d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition at 0 {
+					label = "u-boot";
+					reg = <0x0000000 0x200000>;  /* 2MB */
+					read-only;
+				};
+
+				partition at 100000 {
+					label = "u_env";
+					reg = <0x200000 0x40000>;    /* 256KB */
+				};
+
+				partition at 140000 {
+					label = "s_env";
+					reg = <0x240000 0x40000>;    /* 256KB */
+				};
+
+				partition at 900000 {
+					label = "devinfo";
+					reg = <0x900000 0x100000>;   /* 1MB */
+					read-only;
+				};
+
+				/* kernel1 overlaps with rootfs1 by design */
+				partition at a00000 {
+					label = "kernel1";
+					reg = <0xa00000 0x2800000>;  /* 40MB */
+				};
+
+				partition at 1000000 {
+					label = "rootfs1";
+					reg = <0x1000000 0x2200000>;  /* 34MB */
+				};
+
+				/* kernel2 overlaps with rootfs2 by design */
+				partition at 3200000 {
+					label = "kernel2";
+					reg = <0x3200000 0x2800000>; /* 40MB */
+				};
+
+				partition at 3800000 {
+					label = "rootfs2";
+					reg = <0x3800000 0x2200000>; /* 34MB */
+				};
+
+				/*
+				 * 38MB, last MB is for the BBT, not writable
+				 */
+				partition at 5a00000 {
+					label = "syscfg";
+					reg = <0x5a00000 0x2600000>;
+				};
+
+				/*
+				 * Unused area between "s_env" and "devinfo".
+				 * Moved here because otherwise the renumbered
+				 * partitions would break the bootloader
+				 * supplied bootargs
+				 */
+				partition at 180000 {
+					label = "unused_area";
+					reg = <0x280000 0x680000>;   /* 6.5MB */
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie at 1,0 {
+				/* Marvell 88W8864, 5GHz-only */
+				status = "okay";
+			};
+
+			pcie at 2,0 {
+				/* Marvell 88W8864, 2GHz-only */
+				status = "okay";
+			};
+		};
+	};
+
+	usb3_phy: usb3_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_xhci0_vbus>;
+	};
+
+	reg_xhci0_vbus: xhci0-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci0_vbus_pins>;
+		regulator-name = "xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&keys_pin>;
+		pinctrl-names = "default";
+
+		button at 1 {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+
+		button at 2 {
+			label = "Factory Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&power_led_pin &sata_led_pin>;
+		pinctrl-names = "default";
+
+		power {
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		sata {
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	dsa at 0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth2>;
+		dsa,mii-bus = <&mdio>;
+
+		switch at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0>;	/* MDIO address 0, switch 0 in tree */
+
+			port at 0 {
+				reg = <0>;
+				label = "lan4";
+			};
+
+			port at 1 {
+				reg = <1>;
+				label = "lan3";
+			};
+
+			port at 2 {
+				reg = <2>;
+				label = "lan2";
+			};
+
+			port at 3 {
+				reg = <3>;
+				label = "lan1";
+			};
+
+			port at 4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port at 5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	keys_pin: keys-pin {
+		marvell,pins = "mpp24", "mpp47";
+		marvell,function = "gpio";
+	};
+
+	power_led_pin: power-led-pin {
+		marvell,pins = "mpp55";
+		marvell,function = "gpio";
+	};
+
+	sata_led_pin: sata-led-pin {
+		marvell,pins = "mpp54";
+		marvell,function = "gpio";
+	};
+
+	xhci0_vbus_pins: xhci0-vbus-pins {
+		marvell,pins = "mpp50";
+		marvell,function = "gpio";
+	};
+};
-- 
2.1.0

Re: [PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Gregory CLEMENT]

Hi Imre,

On 20/05/2015 23:14, Imre Kaloz wrote:
> This patch adds support for the Linksys WRT1200AC (Caiman) and
> the Linksys WRT1900AC v2 (Cobra).
> 
> Both boards have:
> 
> - 2 Marvell 88W8864 radios
> - 1 USB 3.0 port
> - 1 USB 2.0/eSATAp port
> - 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
> - 128MB NAND flash
> - 512MB RAM
> 
> Signed-off-by: Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
> 
> ---
> Changes since v1: added DSA support
> ---
> The only difference between the two boards is the radio configuration
> (2x2 vs 3x3), so everything except the leds (to be named properly)
> is in the dtsi file. When the wireless driver will be submitted
> upstream, the powertables (calibration data) will end up in the board
> specific files, tho.

it seems that you missed my comment about removing bootargs and just using
stdout-path = "serial0:115200n8";

If you agree and if there is no remark about the DSA part from Andrew, I can
take car of it while applying your patch on mvebu/dt.


Thanks,

Gregory

[...]

> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi

[...]

> +	chosen {
> +		bootargs = "console=ttyS0,115200";
> +		stdout-path = &uart0;
Just here
> +	};


[...]
-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Gregory CLEMENT]

Hi Imre,

On 20/05/2015 23:14, Imre Kaloz wrote:
> This patch adds support for the Linksys WRT1200AC (Caiman) and
> the Linksys WRT1900AC v2 (Cobra).
> 
> Both boards have:
> 
> - 2 Marvell 88W8864 radios
> - 1 USB 3.0 port
> - 1 USB 2.0/eSATAp port
> - 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
> - 128MB NAND flash
> - 512MB RAM
> 
> Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
> 
> ---
> Changes since v1: added DSA support
> ---
> The only difference between the two boards is the radio configuration
> (2x2 vs 3x3), so everything except the leds (to be named properly)
> is in the dtsi file. When the wireless driver will be submitted
> upstream, the powertables (calibration data) will end up in the board
> specific files, tho.

it seems that you missed my comment about removing bootargs and just using
stdout-path = "serial0:115200n8";

If you agree and if there is no remark about the DSA part from Andrew, I can
take car of it while applying your patch on mvebu/dt.


Thanks,

Gregory

[...]

> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi

[...]

> +	chosen {
> +		bootargs = "console=ttyS0,115200";
> +		stdout-path = &uart0;
Just here
> +	};


[...]
-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

Re: [PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Imre Kaloz]

Hi Gregory,

On Mon, 25 May 2015 14:58:22 +0200, Gregory CLEMENT  
<gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:

<snip>

> it seems that you missed my comment about removing bootargs and just  
> using
> stdout-path = "serial0:115200n8";
>
> If you agree and if there is no remark about the DSA part from Andrew, I  
> can
> take car of it while applying your patch on mvebu/dt.

Sorry, I indeed did miss it. I agree with that change. Andrew?


Thanks,

Imre
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Imre Kaloz]

Hi Gregory,

On Mon, 25 May 2015 14:58:22 +0200, Gregory CLEMENT  
<gregory.clement@free-electrons.com> wrote:

<snip>

> it seems that you missed my comment about removing bootargs and just  
> using
> stdout-path = "serial0:115200n8";
>
> If you agree and if there is no remark about the DSA part from Andrew, I  
> can
> take car of it while applying your patch on mvebu/dt.

Sorry, I indeed did miss it. I agree with that change. Andrew?


Thanks,

Imre

Re: [PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Andrew Lunn]

On Mon, May 25, 2015 at 02:58:22PM +0200, Gregory CLEMENT wrote:
> Hi Imre,
> 
> On 20/05/2015 23:14, Imre Kaloz wrote:
> > This patch adds support for the Linksys WRT1200AC (Caiman) and
> > the Linksys WRT1900AC v2 (Cobra).
> > 
> > Both boards have:
> > 
> > - 2 Marvell 88W8864 radios
> > - 1 USB 3.0 port
> > - 1 USB 2.0/eSATAp port
> > - 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
> > - 128MB NAND flash
> > - 512MB RAM
> > 
> > Signed-off-by: Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
> > 
> > ---
> > Changes since v1: added DSA support
> > ---
> > The only difference between the two boards is the radio configuration
> > (2x2 vs 3x3), so everything except the leds (to be named properly)
> > is in the dtsi file. When the wireless driver will be submitted
> > upstream, the powertables (calibration data) will end up in the board
> > specific files, tho.
> 
> it seems that you missed my comment about removing bootargs and just using
> stdout-path = "serial0:115200n8";
> 
> If you agree and if there is no remark about the DSA part from Andrew, I can
> take car of it while applying your patch on mvebu/dt.

DSA looks fine

Acked-by: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>

Thanks
	Andrew

> 
> 
> Thanks,
> 
> Gregory
> 
> [...]
> 
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
> 
> [...]
> 
> > +	chosen {
> > +		bootargs = "console=ttyS0,115200";
> > +		stdout-path = &uart0;
> Just here
> > +	};
> 
> 
> [...]
> -- 
> Gregory Clement, Free Electrons
> Kernel, drivers, real-time and embedded Linux
> development, consulting, training and support.
> http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Andrew Lunn]

On Mon, May 25, 2015 at 02:58:22PM +0200, Gregory CLEMENT wrote:
> Hi Imre,
> 
> On 20/05/2015 23:14, Imre Kaloz wrote:
> > This patch adds support for the Linksys WRT1200AC (Caiman) and
> > the Linksys WRT1900AC v2 (Cobra).
> > 
> > Both boards have:
> > 
> > - 2 Marvell 88W8864 radios
> > - 1 USB 3.0 port
> > - 1 USB 2.0/eSATAp port
> > - 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
> > - 128MB NAND flash
> > - 512MB RAM
> > 
> > Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
> > 
> > ---
> > Changes since v1: added DSA support
> > ---
> > The only difference between the two boards is the radio configuration
> > (2x2 vs 3x3), so everything except the leds (to be named properly)
> > is in the dtsi file. When the wireless driver will be submitted
> > upstream, the powertables (calibration data) will end up in the board
> > specific files, tho.
> 
> it seems that you missed my comment about removing bootargs and just using
> stdout-path = "serial0:115200n8";
> 
> If you agree and if there is no remark about the DSA part from Andrew, I can
> take car of it while applying your patch on mvebu/dt.

DSA looks fine

Acked-by: Andrew Lunn <andrew@lunn.ch>

Thanks
	Andrew

> 
> 
> Thanks,
> 
> Gregory
> 
> [...]
> 
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
> 
> [...]
> 
> > +	chosen {
> > +		bootargs = "console=ttyS0,115200";
> > +		stdout-path = &uart0;
> Just here
> > +	};
> 
> 
> [...]
> -- 
> Gregory Clement, Free Electrons
> Kernel, drivers, real-time and embedded Linux
> development, consulting, training and support.
> http://free-electrons.com

Re: [PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Gregory CLEMENT]

Hi Andrew, Imre,

On 25/05/2015 16:08, Andrew Lunn wrote:
> On Mon, May 25, 2015 at 02:58:22PM +0200, Gregory CLEMENT wrote:
>> Hi Imre,
>>
>> On 20/05/2015 23:14, Imre Kaloz wrote:
>>> This patch adds support for the Linksys WRT1200AC (Caiman) and
>>> the Linksys WRT1900AC v2 (Cobra).
>>>
>>> Both boards have:
>>>
>>> - 2 Marvell 88W8864 radios
>>> - 1 USB 3.0 port
>>> - 1 USB 2.0/eSATAp port
>>> - 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
>>> - 128MB NAND flash
>>> - 512MB RAM
>>>
>>> Signed-off-by: Imre Kaloz <kaloz-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
>>>
>>> ---
>>> Changes since v1: added DSA support
>>> ---
>>> The only difference between the two boards is the radio configuration
>>> (2x2 vs 3x3), so everything except the leds (to be named properly)
>>> is in the dtsi file. When the wireless driver will be submitted
>>> upstream, the powertables (calibration data) will end up in the board
>>> specific files, tho.
>>
>> it seems that you missed my comment about removing bootargs and just using
>> stdout-path = "serial0:115200n8";
>>
>> If you agree and if there is no remark about the DSA part from Andrew, I can
>> take car of it while applying your patch on mvebu/dt.
> 
> DSA looks fine
> 
> Acked-by: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>

applied on mvebu/dt. I also fixed the title: s/Aramda/Armada/

Thanks,

Gregory


> 
> Thanks
> 	Andrew
> 
>>
>>
>> Thanks,
>>
>> Gregory
>>
>> [...]
>>
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
>>
>> [...]
>>
>>> +	chosen {
>>> +		bootargs = "console=ttyS0,115200";
>>> +		stdout-path = &uart0;
>> Just here
>>> +	};
>>
>>
>> [...]
>> -- 
>> Gregory Clement, Free Electrons
>> Kernel, drivers, real-time and embedded Linux
>> development, consulting, training and support.
>> http://free-electrons.com
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2] ARM: mvebu: add support for the new Aramda 385 based Linksys boards

[Gregory CLEMENT]

Hi Andrew, Imre,

On 25/05/2015 16:08, Andrew Lunn wrote:
> On Mon, May 25, 2015 at 02:58:22PM +0200, Gregory CLEMENT wrote:
>> Hi Imre,
>>
>> On 20/05/2015 23:14, Imre Kaloz wrote:
>>> This patch adds support for the Linksys WRT1200AC (Caiman) and
>>> the Linksys WRT1900AC v2 (Cobra).
>>>
>>> Both boards have:
>>>
>>> - 2 Marvell 88W8864 radios
>>> - 1 USB 3.0 port
>>> - 1 USB 2.0/eSATAp port
>>> - 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
>>> - 128MB NAND flash
>>> - 512MB RAM
>>>
>>> Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
>>>
>>> ---
>>> Changes since v1: added DSA support
>>> ---
>>> The only difference between the two boards is the radio configuration
>>> (2x2 vs 3x3), so everything except the leds (to be named properly)
>>> is in the dtsi file. When the wireless driver will be submitted
>>> upstream, the powertables (calibration data) will end up in the board
>>> specific files, tho.
>>
>> it seems that you missed my comment about removing bootargs and just using
>> stdout-path = "serial0:115200n8";
>>
>> If you agree and if there is no remark about the DSA part from Andrew, I can
>> take car of it while applying your patch on mvebu/dt.
> 
> DSA looks fine
> 
> Acked-by: Andrew Lunn <andrew@lunn.ch>

applied on mvebu/dt. I also fixed the title: s/Aramda/Armada/

Thanks,

Gregory


> 
> Thanks
> 	Andrew
> 
>>
>>
>> Thanks,
>>
>> Gregory
>>
>> [...]
>>
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
>>
>> [...]
>>
>>> +	chosen {
>>> +		bootargs = "console=ttyS0,115200";
>>> +		stdout-path = &uart0;
>> Just here
>>> +	};
>>
>>
>> [...]
>> -- 
>> Gregory Clement, Free Electrons
>> Kernel, drivers, real-time and embedded Linux
>> development, consulting, training and support.
>> http://free-electrons.com
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com