[PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[Josh Wu]

This patch series fix the peripheral clock code and enable runtime support.
Also it clean up the code which is for the compatiblity of mck.

Changes in v5:
- add new patch to fix the condition that codec request still in work.
- fix the error path in start_streaming() thanks to Laurent.

Changes in v4:
- need to call pm_runtime_disable() in atmel_isi_remove().
- merged the patch which remove isi disable code in atmel_isi_probe() as
  isi peripherial clock is not enabled in this moment.
- refine the commit log

Changes in v3:
- remove useless definition: ISI_DEFAULT_MCLK_FREQ

Changes in v2:
- merged v1 two patch into one.
- use runtime_pm_put() instead of runtime_pm_put_sync()
- enable peripheral clock before access ISI registers.
- totally remove clock_start()/clock_stop() as they are optional.

Josh Wu (3):
  media: atmel-isi: disable ISI even it has codec request in
    stop_streaming()
  media: atmel-isi: add runtime pm support
  media: atmel-isi: remove mck back compatiable code as it's not need

 drivers/media/platform/soc_camera/atmel-isi.c | 105 ++++++++++++--------------
 1 file changed, 48 insertions(+), 57 deletions(-)

-- 
1.9.1

[PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[Josh Wu]

This patch series fix the peripheral clock code and enable runtime support.
Also it clean up the code which is for the compatiblity of mck.

Changes in v5:
- add new patch to fix the condition that codec request still in work.
- fix the error path in start_streaming() thanks to Laurent.

Changes in v4:
- need to call pm_runtime_disable() in atmel_isi_remove().
- merged the patch which remove isi disable code in atmel_isi_probe() as
  isi peripherial clock is not enabled in this moment.
- refine the commit log

Changes in v3:
- remove useless definition: ISI_DEFAULT_MCLK_FREQ

Changes in v2:
- merged v1 two patch into one.
- use runtime_pm_put() instead of runtime_pm_put_sync()
- enable peripheral clock before access ISI registers.
- totally remove clock_start()/clock_stop() as they are optional.

Josh Wu (3):
  media: atmel-isi: disable ISI even it has codec request in
    stop_streaming()
  media: atmel-isi: add runtime pm support
  media: atmel-isi: remove mck back compatiable code as it's not need

 drivers/media/platform/soc_camera/atmel-isi.c | 105 ++++++++++++--------------
 1 file changed, 48 insertions(+), 57 deletions(-)

-- 
1.9.1

[PATCH v5 1/3] media: atmel-isi: disable ISI even it has codec request in stop_streaming()

[Josh Wu]

In current code, stop_streaming() will just return if ISI is still
working in the codec. But this is incorrect, we need to disable ISI even
it is working on the codec. otherwise stop_streaming() will not work as
we expected.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
---

Changes in v5:
- add new patch to fix the condition that codec request still in work.

Changes in v4: None
Changes in v3: None
Changes in v2: None

 drivers/media/platform/soc_camera/atmel-isi.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c
index 2879026..2227022 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -431,11 +431,9 @@ static void stop_streaming(struct vb2_queue *vq)
 			time_before(jiffies, timeout))
 		msleep(1);
 
-	if (time_after(jiffies, timeout)) {
+	if (time_after(jiffies, timeout))
 		dev_err(icd->parent,
 			"Timeout waiting for finishing codec request\n");
-		return;
-	}
 
 	/* Disable interrupts */
 	isi_writel(isi, ISI_INTDIS,
-- 
1.9.1

[PATCH v5 1/3] media: atmel-isi: disable ISI even it has codec request in stop_streaming()

[Josh Wu]

In current code, stop_streaming() will just return if ISI is still
working in the codec. But this is incorrect, we need to disable ISI even
it is working on the codec. otherwise stop_streaming() will not work as
we expected.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
---

Changes in v5:
- add new patch to fix the condition that codec request still in work.

Changes in v4: None
Changes in v3: None
Changes in v2: None

 drivers/media/platform/soc_camera/atmel-isi.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c
index 2879026..2227022 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -431,11 +431,9 @@ static void stop_streaming(struct vb2_queue *vq)
 			time_before(jiffies, timeout))
 		msleep(1);
 
-	if (time_after(jiffies, timeout)) {
+	if (time_after(jiffies, timeout))
 		dev_err(icd->parent,
 			"Timeout waiting for finishing codec request\n");
-		return;
-	}
 
 	/* Disable interrupts */
 	isi_writel(isi, ISI_INTDIS,
-- 
1.9.1

[PATCH v5 2/3] media: atmel-isi: add runtime pm support

[Josh Wu]

The runtime pm resume/suspend will enable/disable pclk (ISI peripheral
clock).
And we need to call runtime_pm_get_sync()/runtime_pm_put() when we need
access ISI registers. In atmel_isi_probe(), remove the isi disable code
as in the moment ISI peripheral clock is not enable yet.

In the meantime, as clock_start()/clock_stop() is used to control the
mclk not ISI peripheral clock. So move this to start[stop]_streaming()
function.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
---

Changes in v5:
- fix the error path in start_streaming() thanks to Laurent.

Changes in v4:
- need to call pm_runtime_disable() in atmel_isi_remove().
- merged the patch which remove isi disable code in atmel_isi_probe() as
  isi peripherial clock is not enabled in this moment.
- refine the commit log

Changes in v3: None
Changes in v2:
- merged v1 two patch into one.
- use runtime_pm_put() instead of runtime_pm_put_sync()
- enable peripheral clock before access ISI registers.

 drivers/media/platform/soc_camera/atmel-isi.c | 55 +++++++++++++++++++++++----
 1 file changed, 47 insertions(+), 8 deletions(-)

diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c
index 2227022..0ea360a 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -20,6 +20,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 
 #include <media/atmel-isi.h>
@@ -386,10 +387,13 @@ static int start_streaming(struct vb2_queue *vq, unsigned int count)
 	struct atmel_isi *isi = ici->priv;
 	int ret;
 
+	pm_runtime_get_sync(ici->v4l2_dev.dev);
+
 	/* Reset ISI */
 	ret = atmel_isi_wait_status(isi, WAIT_ISI_RESET);
 	if (ret < 0) {
 		dev_err(icd->parent, "Reset ISI timed out\n");
+		pm_runtime_put(ici->v4l2_dev.dev);
 		return ret;
 	}
 	/* Disable all interrupts */
@@ -443,6 +447,8 @@ static void stop_streaming(struct vb2_queue *vq)
 	ret = atmel_isi_wait_status(isi, WAIT_ISI_DISABLE);
 	if (ret < 0)
 		dev_err(icd->parent, "Disable ISI timed out\n");
+
+	pm_runtime_put(ici->v4l2_dev.dev);
 }
 
 static struct vb2_ops isi_video_qops = {
@@ -514,7 +520,13 @@ static int isi_camera_set_fmt(struct soc_camera_device *icd,
 	if (mf->code != xlate->code)
 		return -EINVAL;
 
+	/* Enable PM and peripheral clock before operate isi registers */
+	pm_runtime_get_sync(ici->v4l2_dev.dev);
+
 	ret = configure_geometry(isi, pix->width, pix->height, xlate->code);
+
+	pm_runtime_put(ici->v4l2_dev.dev);
+
 	if (ret < 0)
 		return ret;
 
@@ -734,14 +746,9 @@ static int isi_camera_clock_start(struct soc_camera_host *ici)
 	struct atmel_isi *isi = ici->priv;
 	int ret;
 
-	ret = clk_prepare_enable(isi->pclk);
-	if (ret)
-		return ret;
-
 	if (!IS_ERR(isi->mck)) {
 		ret = clk_prepare_enable(isi->mck);
 		if (ret) {
-			clk_disable_unprepare(isi->pclk);
 			return ret;
 		}
 	}
@@ -756,7 +763,6 @@ static void isi_camera_clock_stop(struct soc_camera_host *ici)
 
 	if (!IS_ERR(isi->mck))
 		clk_disable_unprepare(isi->mck);
-	clk_disable_unprepare(isi->pclk);
 }
 
 static unsigned int isi_camera_poll(struct file *file, poll_table *pt)
@@ -853,9 +859,14 @@ static int isi_camera_set_bus_param(struct soc_camera_device *icd)
 
 	cfg1 |= ISI_CFG1_THMASK_BEATS_16;
 
+	/* Enable PM and peripheral clock before operate isi registers */
+	pm_runtime_get_sync(ici->v4l2_dev.dev);
+
 	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
 	isi_writel(isi, ISI_CFG1, cfg1);
 
+	pm_runtime_put(ici->v4l2_dev.dev);
+
 	return 0;
 }
 
@@ -887,6 +898,7 @@ static int atmel_isi_remove(struct platform_device *pdev)
 			sizeof(struct fbd) * MAX_BUFFER_NUM,
 			isi->p_fb_descriptors,
 			isi->fb_descriptors_phys);
+	pm_runtime_disable(&pdev->dev);
 
 	return 0;
 }
@@ -1025,8 +1037,6 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	if (isi->pdata.data_width_flags & ISI_DATAWIDTH_10)
 		isi->width_flags |= 1 << 9;
 
-	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
-
 	irq = platform_get_irq(pdev, 0);
 	if (IS_ERR_VALUE(irq)) {
 		ret = irq;
@@ -1047,6 +1057,9 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	soc_host->v4l2_dev.dev	= &pdev->dev;
 	soc_host->nr		= pdev->id;
 
+	pm_suspend_ignore_children(&pdev->dev, true);
+	pm_runtime_enable(&pdev->dev);
+
 	if (isi->pdata.asd_sizes) {
 		soc_host->asd = isi->pdata.asd;
 		soc_host->asd_sizes = isi->pdata.asd_sizes;
@@ -1060,6 +1073,7 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	return 0;
 
 err_register_soc_camera_host:
+	pm_runtime_disable(&pdev->dev);
 err_req_irq:
 err_ioremap:
 	vb2_dma_contig_cleanup_ctx(isi->alloc_ctx);
@@ -1072,6 +1086,30 @@ err_alloc_ctx:
 	return ret;
 }
 
+static int atmel_isi_runtime_suspend(struct device *dev)
+{
+	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
+	struct atmel_isi *isi = container_of(soc_host,
+					struct atmel_isi, soc_host);
+
+	clk_disable_unprepare(isi->pclk);
+
+	return 0;
+}
+static int atmel_isi_runtime_resume(struct device *dev)
+{
+	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
+	struct atmel_isi *isi = container_of(soc_host,
+					struct atmel_isi, soc_host);
+
+	return clk_prepare_enable(isi->pclk);
+}
+
+static const struct dev_pm_ops atmel_isi_dev_pm_ops = {
+	SET_RUNTIME_PM_OPS(atmel_isi_runtime_suspend,
+				atmel_isi_runtime_resume, NULL)
+};
+
 static const struct of_device_id atmel_isi_of_match[] = {
 	{ .compatible = "atmel,at91sam9g45-isi" },
 	{ }
@@ -1083,6 +1121,7 @@ static struct platform_driver atmel_isi_driver = {
 	.driver		= {
 		.name = "atmel_isi",
 		.of_match_table = of_match_ptr(atmel_isi_of_match),
+		.pm	= &atmel_isi_dev_pm_ops,
 	},
 };
 
-- 
1.9.1

[PATCH v5 2/3] media: atmel-isi: add runtime pm support

[Josh Wu]

The runtime pm resume/suspend will enable/disable pclk (ISI peripheral
clock).
And we need to call runtime_pm_get_sync()/runtime_pm_put() when we need
access ISI registers. In atmel_isi_probe(), remove the isi disable code
as in the moment ISI peripheral clock is not enable yet.

In the meantime, as clock_start()/clock_stop() is used to control the
mclk not ISI peripheral clock. So move this to start[stop]_streaming()
function.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
---

Changes in v5:
- fix the error path in start_streaming() thanks to Laurent.

Changes in v4:
- need to call pm_runtime_disable() in atmel_isi_remove().
- merged the patch which remove isi disable code in atmel_isi_probe() as
  isi peripherial clock is not enabled in this moment.
- refine the commit log

Changes in v3: None
Changes in v2:
- merged v1 two patch into one.
- use runtime_pm_put() instead of runtime_pm_put_sync()
- enable peripheral clock before access ISI registers.

 drivers/media/platform/soc_camera/atmel-isi.c | 55 +++++++++++++++++++++++----
 1 file changed, 47 insertions(+), 8 deletions(-)

diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c
index 2227022..0ea360a 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -20,6 +20,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 
 #include <media/atmel-isi.h>
@@ -386,10 +387,13 @@ static int start_streaming(struct vb2_queue *vq, unsigned int count)
 	struct atmel_isi *isi = ici->priv;
 	int ret;
 
+	pm_runtime_get_sync(ici->v4l2_dev.dev);
+
 	/* Reset ISI */
 	ret = atmel_isi_wait_status(isi, WAIT_ISI_RESET);
 	if (ret < 0) {
 		dev_err(icd->parent, "Reset ISI timed out\n");
+		pm_runtime_put(ici->v4l2_dev.dev);
 		return ret;
 	}
 	/* Disable all interrupts */
@@ -443,6 +447,8 @@ static void stop_streaming(struct vb2_queue *vq)
 	ret = atmel_isi_wait_status(isi, WAIT_ISI_DISABLE);
 	if (ret < 0)
 		dev_err(icd->parent, "Disable ISI timed out\n");
+
+	pm_runtime_put(ici->v4l2_dev.dev);
 }
 
 static struct vb2_ops isi_video_qops = {
@@ -514,7 +520,13 @@ static int isi_camera_set_fmt(struct soc_camera_device *icd,
 	if (mf->code != xlate->code)
 		return -EINVAL;
 
+	/* Enable PM and peripheral clock before operate isi registers */
+	pm_runtime_get_sync(ici->v4l2_dev.dev);
+
 	ret = configure_geometry(isi, pix->width, pix->height, xlate->code);
+
+	pm_runtime_put(ici->v4l2_dev.dev);
+
 	if (ret < 0)
 		return ret;
 
@@ -734,14 +746,9 @@ static int isi_camera_clock_start(struct soc_camera_host *ici)
 	struct atmel_isi *isi = ici->priv;
 	int ret;
 
-	ret = clk_prepare_enable(isi->pclk);
-	if (ret)
-		return ret;
-
 	if (!IS_ERR(isi->mck)) {
 		ret = clk_prepare_enable(isi->mck);
 		if (ret) {
-			clk_disable_unprepare(isi->pclk);
 			return ret;
 		}
 	}
@@ -756,7 +763,6 @@ static void isi_camera_clock_stop(struct soc_camera_host *ici)
 
 	if (!IS_ERR(isi->mck))
 		clk_disable_unprepare(isi->mck);
-	clk_disable_unprepare(isi->pclk);
 }
 
 static unsigned int isi_camera_poll(struct file *file, poll_table *pt)
@@ -853,9 +859,14 @@ static int isi_camera_set_bus_param(struct soc_camera_device *icd)
 
 	cfg1 |= ISI_CFG1_THMASK_BEATS_16;
 
+	/* Enable PM and peripheral clock before operate isi registers */
+	pm_runtime_get_sync(ici->v4l2_dev.dev);
+
 	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
 	isi_writel(isi, ISI_CFG1, cfg1);
 
+	pm_runtime_put(ici->v4l2_dev.dev);
+
 	return 0;
 }
 
@@ -887,6 +898,7 @@ static int atmel_isi_remove(struct platform_device *pdev)
 			sizeof(struct fbd) * MAX_BUFFER_NUM,
 			isi->p_fb_descriptors,
 			isi->fb_descriptors_phys);
+	pm_runtime_disable(&pdev->dev);
 
 	return 0;
 }
@@ -1025,8 +1037,6 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	if (isi->pdata.data_width_flags & ISI_DATAWIDTH_10)
 		isi->width_flags |= 1 << 9;
 
-	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
-
 	irq = platform_get_irq(pdev, 0);
 	if (IS_ERR_VALUE(irq)) {
 		ret = irq;
@@ -1047,6 +1057,9 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	soc_host->v4l2_dev.dev	= &pdev->dev;
 	soc_host->nr		= pdev->id;
 
+	pm_suspend_ignore_children(&pdev->dev, true);
+	pm_runtime_enable(&pdev->dev);
+
 	if (isi->pdata.asd_sizes) {
 		soc_host->asd = isi->pdata.asd;
 		soc_host->asd_sizes = isi->pdata.asd_sizes;
@@ -1060,6 +1073,7 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	return 0;
 
 err_register_soc_camera_host:
+	pm_runtime_disable(&pdev->dev);
 err_req_irq:
 err_ioremap:
 	vb2_dma_contig_cleanup_ctx(isi->alloc_ctx);
@@ -1072,6 +1086,30 @@ err_alloc_ctx:
 	return ret;
 }
 
+static int atmel_isi_runtime_suspend(struct device *dev)
+{
+	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
+	struct atmel_isi *isi = container_of(soc_host,
+					struct atmel_isi, soc_host);
+
+	clk_disable_unprepare(isi->pclk);
+
+	return 0;
+}
+static int atmel_isi_runtime_resume(struct device *dev)
+{
+	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
+	struct atmel_isi *isi = container_of(soc_host,
+					struct atmel_isi, soc_host);
+
+	return clk_prepare_enable(isi->pclk);
+}
+
+static const struct dev_pm_ops atmel_isi_dev_pm_ops = {
+	SET_RUNTIME_PM_OPS(atmel_isi_runtime_suspend,
+				atmel_isi_runtime_resume, NULL)
+};
+
 static const struct of_device_id atmel_isi_of_match[] = {
 	{ .compatible = "atmel,at91sam9g45-isi" },
 	{ }
@@ -1083,6 +1121,7 @@ static struct platform_driver atmel_isi_driver = {
 	.driver		= {
 		.name = "atmel_isi",
 		.of_match_table = of_match_ptr(atmel_isi_of_match),
+		.pm	= &atmel_isi_dev_pm_ops,
 	},
 };
 
-- 
1.9.1

[PATCH v5 3/3] media: atmel-isi: remove mck back compatiable code as it's not need

[Josh Wu]

The master clock should handled by sensor itself.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---

Changes in v5: None
Changes in v4: None
Changes in v3:
- remove useless definition: ISI_DEFAULT_MCLK_FREQ

Changes in v2:
- totally remove clock_start()/clock_stop() as they are optional.

 drivers/media/platform/soc_camera/atmel-isi.c | 46 ---------------------------
 1 file changed, 46 deletions(-)

diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c
index 0ea360a..9070172 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -35,7 +35,6 @@
 #define VID_LIMIT_BYTES			(16 * 1024 * 1024)
 #define MIN_FRAME_RATE			15
 #define FRAME_INTERVAL_MILLI_SEC	(1000 / MIN_FRAME_RATE)
-#define ISI_DEFAULT_MCLK_FREQ		25000000
 
 /* Frame buffer descriptor */
 struct fbd {
@@ -83,8 +82,6 @@ struct atmel_isi {
 	struct completion		complete;
 	/* ISI peripherial clock */
 	struct clk			*pclk;
-	/* ISI_MCK, feed to camera sensor to generate pixel clock */
-	struct clk			*mck;
 	unsigned int			irq;
 
 	struct isi_platform_data	pdata;
@@ -740,31 +737,6 @@ static void isi_camera_remove_device(struct soc_camera_device *icd)
 		 icd->devnum);
 }
 
-/* Called with .host_lock held */
-static int isi_camera_clock_start(struct soc_camera_host *ici)
-{
-	struct atmel_isi *isi = ici->priv;
-	int ret;
-
-	if (!IS_ERR(isi->mck)) {
-		ret = clk_prepare_enable(isi->mck);
-		if (ret) {
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-/* Called with .host_lock held */
-static void isi_camera_clock_stop(struct soc_camera_host *ici)
-{
-	struct atmel_isi *isi = ici->priv;
-
-	if (!IS_ERR(isi->mck))
-		clk_disable_unprepare(isi->mck);
-}
-
 static unsigned int isi_camera_poll(struct file *file, poll_table *pt)
 {
 	struct soc_camera_device *icd = file->private_data;
@@ -874,8 +846,6 @@ static struct soc_camera_host_ops isi_soc_camera_host_ops = {
 	.owner		= THIS_MODULE,
 	.add		= isi_camera_add_device,
 	.remove		= isi_camera_remove_device,
-	.clock_start	= isi_camera_clock_start,
-	.clock_stop	= isi_camera_clock_stop,
 	.set_fmt	= isi_camera_set_fmt,
 	.try_fmt	= isi_camera_try_fmt,
 	.get_formats	= isi_camera_get_formats,
@@ -912,7 +882,6 @@ static int atmel_isi_probe_dt(struct atmel_isi *isi,
 
 	/* Default settings for ISI */
 	isi->pdata.full_mode = 1;
-	isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ;
 	isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL;
 
 	np = of_graph_get_next_endpoint(np, NULL);
@@ -988,21 +957,6 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	INIT_LIST_HEAD(&isi->video_buffer_list);
 	INIT_LIST_HEAD(&isi->dma_desc_head);
 
-	/* ISI_MCK is the sensor master clock. It should be handled by the
-	 * sensor driver directly, as the ISI has no use for that clock. Make
-	 * the clock optional here while platforms transition to the correct
-	 * model.
-	 */
-	isi->mck = devm_clk_get(dev, "isi_mck");
-	if (!IS_ERR(isi->mck)) {
-		/* Set ISI_MCK's frequency, it should be faster than pixel
-		 * clock.
-		 */
-		ret = clk_set_rate(isi->mck, isi->pdata.mck_hz);
-		if (ret < 0)
-			return ret;
-	}
-
 	isi->p_fb_descriptors = dma_alloc_coherent(&pdev->dev,
 				sizeof(struct fbd) * MAX_BUFFER_NUM,
 				&isi->fb_descriptors_phys,
-- 
1.9.1

[PATCH v5 3/3] media: atmel-isi: remove mck back compatiable code as it's not need

[Josh Wu]

The master clock should handled by sensor itself.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---

Changes in v5: None
Changes in v4: None
Changes in v3:
- remove useless definition: ISI_DEFAULT_MCLK_FREQ

Changes in v2:
- totally remove clock_start()/clock_stop() as they are optional.

 drivers/media/platform/soc_camera/atmel-isi.c | 46 ---------------------------
 1 file changed, 46 deletions(-)

diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c
index 0ea360a..9070172 100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -35,7 +35,6 @@
 #define VID_LIMIT_BYTES			(16 * 1024 * 1024)
 #define MIN_FRAME_RATE			15
 #define FRAME_INTERVAL_MILLI_SEC	(1000 / MIN_FRAME_RATE)
-#define ISI_DEFAULT_MCLK_FREQ		25000000
 
 /* Frame buffer descriptor */
 struct fbd {
@@ -83,8 +82,6 @@ struct atmel_isi {
 	struct completion		complete;
 	/* ISI peripherial clock */
 	struct clk			*pclk;
-	/* ISI_MCK, feed to camera sensor to generate pixel clock */
-	struct clk			*mck;
 	unsigned int			irq;
 
 	struct isi_platform_data	pdata;
@@ -740,31 +737,6 @@ static void isi_camera_remove_device(struct soc_camera_device *icd)
 		 icd->devnum);
 }
 
-/* Called with .host_lock held */
-static int isi_camera_clock_start(struct soc_camera_host *ici)
-{
-	struct atmel_isi *isi = ici->priv;
-	int ret;
-
-	if (!IS_ERR(isi->mck)) {
-		ret = clk_prepare_enable(isi->mck);
-		if (ret) {
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-/* Called with .host_lock held */
-static void isi_camera_clock_stop(struct soc_camera_host *ici)
-{
-	struct atmel_isi *isi = ici->priv;
-
-	if (!IS_ERR(isi->mck))
-		clk_disable_unprepare(isi->mck);
-}
-
 static unsigned int isi_camera_poll(struct file *file, poll_table *pt)
 {
 	struct soc_camera_device *icd = file->private_data;
@@ -874,8 +846,6 @@ static struct soc_camera_host_ops isi_soc_camera_host_ops = {
 	.owner		= THIS_MODULE,
 	.add		= isi_camera_add_device,
 	.remove		= isi_camera_remove_device,
-	.clock_start	= isi_camera_clock_start,
-	.clock_stop	= isi_camera_clock_stop,
 	.set_fmt	= isi_camera_set_fmt,
 	.try_fmt	= isi_camera_try_fmt,
 	.get_formats	= isi_camera_get_formats,
@@ -912,7 +882,6 @@ static int atmel_isi_probe_dt(struct atmel_isi *isi,
 
 	/* Default settings for ISI */
 	isi->pdata.full_mode = 1;
-	isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ;
 	isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL;
 
 	np = of_graph_get_next_endpoint(np, NULL);
@@ -988,21 +957,6 @@ static int atmel_isi_probe(struct platform_device *pdev)
 	INIT_LIST_HEAD(&isi->video_buffer_list);
 	INIT_LIST_HEAD(&isi->dma_desc_head);
 
-	/* ISI_MCK is the sensor master clock. It should be handled by the
-	 * sensor driver directly, as the ISI has no use for that clock. Make
-	 * the clock optional here while platforms transition to the correct
-	 * model.
-	 */
-	isi->mck = devm_clk_get(dev, "isi_mck");
-	if (!IS_ERR(isi->mck)) {
-		/* Set ISI_MCK's frequency, it should be faster than pixel
-		 * clock.
-		 */
-		ret = clk_set_rate(isi->mck, isi->pdata.mck_hz);
-		if (ret < 0)
-			return ret;
-	}
-
 	isi->p_fb_descriptors = dma_alloc_coherent(&pdev->dev,
 				sizeof(struct fbd) * MAX_BUFFER_NUM,
 				&isi->fb_descriptors_phys,
-- 
1.9.1

Re: [PATCH v5 2/3] media: atmel-isi: add runtime pm support

[Laurent Pinchart]

Hi Josh,

Thank you for the patch.

On Tuesday 26 May 2015 17:54:46 Josh Wu wrote:
> The runtime pm resume/suspend will enable/disable pclk (ISI peripheral
> clock).
> And we need to call runtime_pm_get_sync()/runtime_pm_put() when we need
> access ISI registers. In atmel_isi_probe(), remove the isi disable code
> as in the moment ISI peripheral clock is not enable yet.
> 
> In the meantime, as clock_start()/clock_stop() is used to control the
> mclk not ISI peripheral clock. So move this to start[stop]_streaming()
> function.
> 
> Signed-off-by: Josh Wu <josh.wu@atmel.com>

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
> 
> Changes in v5:
> - fix the error path in start_streaming() thanks to Laurent.
> 
> Changes in v4:
> - need to call pm_runtime_disable() in atmel_isi_remove().
> - merged the patch which remove isi disable code in atmel_isi_probe() as
>   isi peripherial clock is not enabled in this moment.
> - refine the commit log
> 
> Changes in v3: None
> Changes in v2:
> - merged v1 two patch into one.
> - use runtime_pm_put() instead of runtime_pm_put_sync()
> - enable peripheral clock before access ISI registers.
> 
>  drivers/media/platform/soc_camera/atmel-isi.c | 55 ++++++++++++++++++++----
>  1 file changed, 47 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/media/platform/soc_camera/atmel-isi.c
> b/drivers/media/platform/soc_camera/atmel-isi.c index 2227022..0ea360a
> 100644
> --- a/drivers/media/platform/soc_camera/atmel-isi.c
> +++ b/drivers/media/platform/soc_camera/atmel-isi.c
> @@ -20,6 +20,7 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/slab.h>
> 
>  #include <media/atmel-isi.h>
> @@ -386,10 +387,13 @@ static int start_streaming(struct vb2_queue *vq,
> unsigned int count) struct atmel_isi *isi = ici->priv;
>  	int ret;
> 
> +	pm_runtime_get_sync(ici->v4l2_dev.dev);
> +
>  	/* Reset ISI */
>  	ret = atmel_isi_wait_status(isi, WAIT_ISI_RESET);
>  	if (ret < 0) {
>  		dev_err(icd->parent, "Reset ISI timed out\n");
> +		pm_runtime_put(ici->v4l2_dev.dev);
>  		return ret;
>  	}
>  	/* Disable all interrupts */
> @@ -443,6 +447,8 @@ static void stop_streaming(struct vb2_queue *vq)
>  	ret = atmel_isi_wait_status(isi, WAIT_ISI_DISABLE);
>  	if (ret < 0)
>  		dev_err(icd->parent, "Disable ISI timed out\n");
> +
> +	pm_runtime_put(ici->v4l2_dev.dev);
>  }
> 
>  static struct vb2_ops isi_video_qops = {
> @@ -514,7 +520,13 @@ static int isi_camera_set_fmt(struct soc_camera_device
> *icd, if (mf->code != xlate->code)
>  		return -EINVAL;
> 
> +	/* Enable PM and peripheral clock before operate isi registers */
> +	pm_runtime_get_sync(ici->v4l2_dev.dev);
> +
>  	ret = configure_geometry(isi, pix->width, pix->height, xlate->code);
> +
> +	pm_runtime_put(ici->v4l2_dev.dev);
> +
>  	if (ret < 0)
>  		return ret;
> 
> @@ -734,14 +746,9 @@ static int isi_camera_clock_start(struct
> soc_camera_host *ici) struct atmel_isi *isi = ici->priv;
>  	int ret;
> 
> -	ret = clk_prepare_enable(isi->pclk);
> -	if (ret)
> -		return ret;
> -
>  	if (!IS_ERR(isi->mck)) {
>  		ret = clk_prepare_enable(isi->mck);
>  		if (ret) {
> -			clk_disable_unprepare(isi->pclk);
>  			return ret;
>  		}
>  	}
> @@ -756,7 +763,6 @@ static void isi_camera_clock_stop(struct soc_camera_host
> *ici)
> 
>  	if (!IS_ERR(isi->mck))
>  		clk_disable_unprepare(isi->mck);
> -	clk_disable_unprepare(isi->pclk);
>  }
> 
>  static unsigned int isi_camera_poll(struct file *file, poll_table *pt)
> @@ -853,9 +859,14 @@ static int isi_camera_set_bus_param(struct
> soc_camera_device *icd)
> 
>  	cfg1 |= ISI_CFG1_THMASK_BEATS_16;
> 
> +	/* Enable PM and peripheral clock before operate isi registers */
> +	pm_runtime_get_sync(ici->v4l2_dev.dev);
> +
>  	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
>  	isi_writel(isi, ISI_CFG1, cfg1);
> 
> +	pm_runtime_put(ici->v4l2_dev.dev);
> +
>  	return 0;
>  }
> 
> @@ -887,6 +898,7 @@ static int atmel_isi_remove(struct platform_device
> *pdev) sizeof(struct fbd) * MAX_BUFFER_NUM,
>  			isi->p_fb_descriptors,
>  			isi->fb_descriptors_phys);
> +	pm_runtime_disable(&pdev->dev);
> 
>  	return 0;
>  }
> @@ -1025,8 +1037,6 @@ static int atmel_isi_probe(struct platform_device
> *pdev) if (isi->pdata.data_width_flags & ISI_DATAWIDTH_10)
>  		isi->width_flags |= 1 << 9;
> 
> -	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
> -
>  	irq = platform_get_irq(pdev, 0);
>  	if (IS_ERR_VALUE(irq)) {
>  		ret = irq;
> @@ -1047,6 +1057,9 @@ static int atmel_isi_probe(struct platform_device
> *pdev) soc_host->v4l2_dev.dev	= &pdev->dev;
>  	soc_host->nr		= pdev->id;
> 
> +	pm_suspend_ignore_children(&pdev->dev, true);
> +	pm_runtime_enable(&pdev->dev);
> +
>  	if (isi->pdata.asd_sizes) {
>  		soc_host->asd = isi->pdata.asd;
>  		soc_host->asd_sizes = isi->pdata.asd_sizes;
> @@ -1060,6 +1073,7 @@ static int atmel_isi_probe(struct platform_device
> *pdev) return 0;
> 
>  err_register_soc_camera_host:
> +	pm_runtime_disable(&pdev->dev);
>  err_req_irq:
>  err_ioremap:
>  	vb2_dma_contig_cleanup_ctx(isi->alloc_ctx);
> @@ -1072,6 +1086,30 @@ err_alloc_ctx:
>  	return ret;
>  }
> 
> +static int atmel_isi_runtime_suspend(struct device *dev)
> +{
> +	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
> +	struct atmel_isi *isi = container_of(soc_host,
> +					struct atmel_isi, soc_host);
> +
> +	clk_disable_unprepare(isi->pclk);
> +
> +	return 0;
> +}
> +static int atmel_isi_runtime_resume(struct device *dev)
> +{
> +	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
> +	struct atmel_isi *isi = container_of(soc_host,
> +					struct atmel_isi, soc_host);
> +
> +	return clk_prepare_enable(isi->pclk);
> +}
> +
> +static const struct dev_pm_ops atmel_isi_dev_pm_ops = {
> +	SET_RUNTIME_PM_OPS(atmel_isi_runtime_suspend,
> +				atmel_isi_runtime_resume, NULL)
> +};
> +
>  static const struct of_device_id atmel_isi_of_match[] = {
>  	{ .compatible = "atmel,at91sam9g45-isi" },
>  	{ }
> @@ -1083,6 +1121,7 @@ static struct platform_driver atmel_isi_driver = {
>  	.driver		= {
>  		.name = "atmel_isi",
>  		.of_match_table = of_match_ptr(atmel_isi_of_match),
> +		.pm	= &atmel_isi_dev_pm_ops,
>  	},
>  };

-- 
Regards,

Laurent Pinchart

[PATCH v5 2/3] media: atmel-isi: add runtime pm support

[Laurent Pinchart]

Hi Josh,

Thank you for the patch.

On Tuesday 26 May 2015 17:54:46 Josh Wu wrote:
> The runtime pm resume/suspend will enable/disable pclk (ISI peripheral
> clock).
> And we need to call runtime_pm_get_sync()/runtime_pm_put() when we need
> access ISI registers. In atmel_isi_probe(), remove the isi disable code
> as in the moment ISI peripheral clock is not enable yet.
> 
> In the meantime, as clock_start()/clock_stop() is used to control the
> mclk not ISI peripheral clock. So move this to start[stop]_streaming()
> function.
> 
> Signed-off-by: Josh Wu <josh.wu@atmel.com>

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
> 
> Changes in v5:
> - fix the error path in start_streaming() thanks to Laurent.
> 
> Changes in v4:
> - need to call pm_runtime_disable() in atmel_isi_remove().
> - merged the patch which remove isi disable code in atmel_isi_probe() as
>   isi peripherial clock is not enabled in this moment.
> - refine the commit log
> 
> Changes in v3: None
> Changes in v2:
> - merged v1 two patch into one.
> - use runtime_pm_put() instead of runtime_pm_put_sync()
> - enable peripheral clock before access ISI registers.
> 
>  drivers/media/platform/soc_camera/atmel-isi.c | 55 ++++++++++++++++++++----
>  1 file changed, 47 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/media/platform/soc_camera/atmel-isi.c
> b/drivers/media/platform/soc_camera/atmel-isi.c index 2227022..0ea360a
> 100644
> --- a/drivers/media/platform/soc_camera/atmel-isi.c
> +++ b/drivers/media/platform/soc_camera/atmel-isi.c
> @@ -20,6 +20,7 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/slab.h>
> 
>  #include <media/atmel-isi.h>
> @@ -386,10 +387,13 @@ static int start_streaming(struct vb2_queue *vq,
> unsigned int count) struct atmel_isi *isi = ici->priv;
>  	int ret;
> 
> +	pm_runtime_get_sync(ici->v4l2_dev.dev);
> +
>  	/* Reset ISI */
>  	ret = atmel_isi_wait_status(isi, WAIT_ISI_RESET);
>  	if (ret < 0) {
>  		dev_err(icd->parent, "Reset ISI timed out\n");
> +		pm_runtime_put(ici->v4l2_dev.dev);
>  		return ret;
>  	}
>  	/* Disable all interrupts */
> @@ -443,6 +447,8 @@ static void stop_streaming(struct vb2_queue *vq)
>  	ret = atmel_isi_wait_status(isi, WAIT_ISI_DISABLE);
>  	if (ret < 0)
>  		dev_err(icd->parent, "Disable ISI timed out\n");
> +
> +	pm_runtime_put(ici->v4l2_dev.dev);
>  }
> 
>  static struct vb2_ops isi_video_qops = {
> @@ -514,7 +520,13 @@ static int isi_camera_set_fmt(struct soc_camera_device
> *icd, if (mf->code != xlate->code)
>  		return -EINVAL;
> 
> +	/* Enable PM and peripheral clock before operate isi registers */
> +	pm_runtime_get_sync(ici->v4l2_dev.dev);
> +
>  	ret = configure_geometry(isi, pix->width, pix->height, xlate->code);
> +
> +	pm_runtime_put(ici->v4l2_dev.dev);
> +
>  	if (ret < 0)
>  		return ret;
> 
> @@ -734,14 +746,9 @@ static int isi_camera_clock_start(struct
> soc_camera_host *ici) struct atmel_isi *isi = ici->priv;
>  	int ret;
> 
> -	ret = clk_prepare_enable(isi->pclk);
> -	if (ret)
> -		return ret;
> -
>  	if (!IS_ERR(isi->mck)) {
>  		ret = clk_prepare_enable(isi->mck);
>  		if (ret) {
> -			clk_disable_unprepare(isi->pclk);
>  			return ret;
>  		}
>  	}
> @@ -756,7 +763,6 @@ static void isi_camera_clock_stop(struct soc_camera_host
> *ici)
> 
>  	if (!IS_ERR(isi->mck))
>  		clk_disable_unprepare(isi->mck);
> -	clk_disable_unprepare(isi->pclk);
>  }
> 
>  static unsigned int isi_camera_poll(struct file *file, poll_table *pt)
> @@ -853,9 +859,14 @@ static int isi_camera_set_bus_param(struct
> soc_camera_device *icd)
> 
>  	cfg1 |= ISI_CFG1_THMASK_BEATS_16;
> 
> +	/* Enable PM and peripheral clock before operate isi registers */
> +	pm_runtime_get_sync(ici->v4l2_dev.dev);
> +
>  	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
>  	isi_writel(isi, ISI_CFG1, cfg1);
> 
> +	pm_runtime_put(ici->v4l2_dev.dev);
> +
>  	return 0;
>  }
> 
> @@ -887,6 +898,7 @@ static int atmel_isi_remove(struct platform_device
> *pdev) sizeof(struct fbd) * MAX_BUFFER_NUM,
>  			isi->p_fb_descriptors,
>  			isi->fb_descriptors_phys);
> +	pm_runtime_disable(&pdev->dev);
> 
>  	return 0;
>  }
> @@ -1025,8 +1037,6 @@ static int atmel_isi_probe(struct platform_device
> *pdev) if (isi->pdata.data_width_flags & ISI_DATAWIDTH_10)
>  		isi->width_flags |= 1 << 9;
> 
> -	isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
> -
>  	irq = platform_get_irq(pdev, 0);
>  	if (IS_ERR_VALUE(irq)) {
>  		ret = irq;
> @@ -1047,6 +1057,9 @@ static int atmel_isi_probe(struct platform_device
> *pdev) soc_host->v4l2_dev.dev	= &pdev->dev;
>  	soc_host->nr		= pdev->id;
> 
> +	pm_suspend_ignore_children(&pdev->dev, true);
> +	pm_runtime_enable(&pdev->dev);
> +
>  	if (isi->pdata.asd_sizes) {
>  		soc_host->asd = isi->pdata.asd;
>  		soc_host->asd_sizes = isi->pdata.asd_sizes;
> @@ -1060,6 +1073,7 @@ static int atmel_isi_probe(struct platform_device
> *pdev) return 0;
> 
>  err_register_soc_camera_host:
> +	pm_runtime_disable(&pdev->dev);
>  err_req_irq:
>  err_ioremap:
>  	vb2_dma_contig_cleanup_ctx(isi->alloc_ctx);
> @@ -1072,6 +1086,30 @@ err_alloc_ctx:
>  	return ret;
>  }
> 
> +static int atmel_isi_runtime_suspend(struct device *dev)
> +{
> +	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
> +	struct atmel_isi *isi = container_of(soc_host,
> +					struct atmel_isi, soc_host);
> +
> +	clk_disable_unprepare(isi->pclk);
> +
> +	return 0;
> +}
> +static int atmel_isi_runtime_resume(struct device *dev)
> +{
> +	struct soc_camera_host *soc_host = to_soc_camera_host(dev);
> +	struct atmel_isi *isi = container_of(soc_host,
> +					struct atmel_isi, soc_host);
> +
> +	return clk_prepare_enable(isi->pclk);
> +}
> +
> +static const struct dev_pm_ops atmel_isi_dev_pm_ops = {
> +	SET_RUNTIME_PM_OPS(atmel_isi_runtime_suspend,
> +				atmel_isi_runtime_resume, NULL)
> +};
> +
>  static const struct of_device_id atmel_isi_of_match[] = {
>  	{ .compatible = "atmel,at91sam9g45-isi" },
>  	{ }
> @@ -1083,6 +1121,7 @@ static struct platform_driver atmel_isi_driver = {
>  	.driver		= {
>  		.name = "atmel_isi",
>  		.of_match_table = of_match_ptr(atmel_isi_of_match),
> +		.pm	= &atmel_isi_dev_pm_ops,
>  	},
>  };

-- 
Regards,

Laurent Pinchart

Re: [PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[Josh Wu]

Hi, Guennadi

Any feedback for this patch series?

Best Regards,
Josh Wu

On 5/26/2015 5:54 PM, Josh Wu wrote:
> This patch series fix the peripheral clock code and enable runtime support.
> Also it clean up the code which is for the compatiblity of mck.
>
> Changes in v5:
> - add new patch to fix the condition that codec request still in work.
> - fix the error path in start_streaming() thanks to Laurent.
>
> Changes in v4:
> - need to call pm_runtime_disable() in atmel_isi_remove().
> - merged the patch which remove isi disable code in atmel_isi_probe() as
>    isi peripherial clock is not enabled in this moment.
> - refine the commit log
>
> Changes in v3:
> - remove useless definition: ISI_DEFAULT_MCLK_FREQ
>
> Changes in v2:
> - merged v1 two patch into one.
> - use runtime_pm_put() instead of runtime_pm_put_sync()
> - enable peripheral clock before access ISI registers.
> - totally remove clock_start()/clock_stop() as they are optional.
>
> Josh Wu (3):
>    media: atmel-isi: disable ISI even it has codec request in
>      stop_streaming()
>    media: atmel-isi: add runtime pm support
>    media: atmel-isi: remove mck back compatiable code as it's not need
>
>   drivers/media/platform/soc_camera/atmel-isi.c | 105 ++++++++++++--------------
>   1 file changed, 48 insertions(+), 57 deletions(-)
>

[PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[Josh Wu]

Hi, Guennadi

Any feedback for this patch series?

Best Regards,
Josh Wu

On 5/26/2015 5:54 PM, Josh Wu wrote:
> This patch series fix the peripheral clock code and enable runtime support.
> Also it clean up the code which is for the compatiblity of mck.
>
> Changes in v5:
> - add new patch to fix the condition that codec request still in work.
> - fix the error path in start_streaming() thanks to Laurent.
>
> Changes in v4:
> - need to call pm_runtime_disable() in atmel_isi_remove().
> - merged the patch which remove isi disable code in atmel_isi_probe() as
>    isi peripherial clock is not enabled in this moment.
> - refine the commit log
>
> Changes in v3:
> - remove useless definition: ISI_DEFAULT_MCLK_FREQ
>
> Changes in v2:
> - merged v1 two patch into one.
> - use runtime_pm_put() instead of runtime_pm_put_sync()
> - enable peripheral clock before access ISI registers.
> - totally remove clock_start()/clock_stop() as they are optional.
>
> Josh Wu (3):
>    media: atmel-isi: disable ISI even it has codec request in
>      stop_streaming()
>    media: atmel-isi: add runtime pm support
>    media: atmel-isi: remove mck back compatiable code as it's not need
>
>   drivers/media/platform/soc_camera/atmel-isi.c | 105 ++++++++++++--------------
>   1 file changed, 48 insertions(+), 57 deletions(-)
>

Re: [PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[Guennadi Liakhovetski]

Hi Josh,

On Thu, 11 Jun 2015, Josh Wu wrote:

> Hi, Guennadi
> 
> Any feedback for this patch series?

Sorry, I haven't found the time to look at patches from you and William 
Towle, they are at the top of my todo list now - after all the compulsory 
things, of course. I'll handle them as soon as I find time. Sorry for the 
delay.

Thanks
Guennadi

> Best Regards,
> Josh Wu
> 
> On 5/26/2015 5:54 PM, Josh Wu wrote:
> > This patch series fix the peripheral clock code and enable runtime support.
> > Also it clean up the code which is for the compatiblity of mck.
> > 
> > Changes in v5:
> > - add new patch to fix the condition that codec request still in work.
> > - fix the error path in start_streaming() thanks to Laurent.
> > 
> > Changes in v4:
> > - need to call pm_runtime_disable() in atmel_isi_remove().
> > - merged the patch which remove isi disable code in atmel_isi_probe() as
> >    isi peripherial clock is not enabled in this moment.
> > - refine the commit log
> > 
> > Changes in v3:
> > - remove useless definition: ISI_DEFAULT_MCLK_FREQ
> > 
> > Changes in v2:
> > - merged v1 two patch into one.
> > - use runtime_pm_put() instead of runtime_pm_put_sync()
> > - enable peripheral clock before access ISI registers.
> > - totally remove clock_start()/clock_stop() as they are optional.
> > 
> > Josh Wu (3):
> >    media: atmel-isi: disable ISI even it has codec request in
> >      stop_streaming()
> >    media: atmel-isi: add runtime pm support
> >    media: atmel-isi: remove mck back compatiable code as it's not need
> > 
> >   drivers/media/platform/soc_camera/atmel-isi.c | 105
> > ++++++++++++--------------
> >   1 file changed, 48 insertions(+), 57 deletions(-)
> > 
> 

[PATCH v5 0/3] media: atmel-isi: rework on the clock part and add runtime pm support

[Guennadi Liakhovetski]

Hi Josh,

On Thu, 11 Jun 2015, Josh Wu wrote:

> Hi, Guennadi
> 
> Any feedback for this patch series?

Sorry, I haven't found the time to look at patches from you and William 
Towle, they are at the top of my todo list now - after all the compulsory 
things, of course. I'll handle them as soon as I find time. Sorry for the 
delay.

Thanks
Guennadi

> Best Regards,
> Josh Wu
> 
> On 5/26/2015 5:54 PM, Josh Wu wrote:
> > This patch series fix the peripheral clock code and enable runtime support.
> > Also it clean up the code which is for the compatiblity of mck.
> > 
> > Changes in v5:
> > - add new patch to fix the condition that codec request still in work.
> > - fix the error path in start_streaming() thanks to Laurent.
> > 
> > Changes in v4:
> > - need to call pm_runtime_disable() in atmel_isi_remove().
> > - merged the patch which remove isi disable code in atmel_isi_probe() as
> >    isi peripherial clock is not enabled in this moment.
> > - refine the commit log
> > 
> > Changes in v3:
> > - remove useless definition: ISI_DEFAULT_MCLK_FREQ
> > 
> > Changes in v2:
> > - merged v1 two patch into one.
> > - use runtime_pm_put() instead of runtime_pm_put_sync()
> > - enable peripheral clock before access ISI registers.
> > - totally remove clock_start()/clock_stop() as they are optional.
> > 
> > Josh Wu (3):
> >    media: atmel-isi: disable ISI even it has codec request in
> >      stop_streaming()
> >    media: atmel-isi: add runtime pm support
> >    media: atmel-isi: remove mck back compatiable code as it's not need
> > 
> >   drivers/media/platform/soc_camera/atmel-isi.c | 105
> > ++++++++++++--------------
> >   1 file changed, 48 insertions(+), 57 deletions(-)
> > 
>