[PATCH 00/16] AT91 DT for 4.2

[PATCH 00/16] AT91 DT for 4.2

[Alexandre Belloni]

Hi,

A dt series for 4.2:
 - Fix at91sam9rl RTC node and use it on at91sam9rlek
 - correct stdout-path for the various kizboxes
 - add stdout-path to the atme evaluation boards
 - add  Acme arietta g25 device tree

Alexandre Belloni (16):
  ARM: at91/dt: at91sam9rl: fix rtc node
  ARM: at91/dt: at91sam9rlek: add RTC
  ARM: at91/dt: kizbox: use stdout-path
  ARM: at91/dt: at91rm9200ek: use stdout-path
  ARM: at91/dt: at91sam9261ek: use stdout-path
  ARM: at91/dt: at91sam9263ek: use stdout-path
  ARM: at91/dt: at91sam9g20ek: use stdout-path
  ARM: at91/dt: at91sam9m10g45ek use stdout-path
  ARM: at91/dt: at91sam9n12ek: use stdout-path
  ARM: at91/dt: at91sam9rlek: use stdout-path
  ARM: at91/dt: at91sam9x5ek: use stdout-path
  ARM: at91/dt: sama5d3xek: use stdout-path
  ARM: at91/dt: sama5d3 xplained: use stdout-path
  ARM: at91/dt: sama5d4ek: use stdout-path
  ARM: at91/dt: sama5d4 xplained: use stdout-path
  ARM: at91/dt: Add Acme Arietta G25

 arch/arm/boot/dts/Makefile                  |  1 +
 arch/arm/boot/dts/at91-acme-arietta.dts     | 75 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/at91-kizbox.dts           |  2 +-
 arch/arm/boot/dts/at91-kizbox2.dts          |  2 +-
 arch/arm/boot/dts/at91-kizboxmini.dts       |  2 +-
 arch/arm/boot/dts/at91-sama5d3_xplained.dts |  2 +-
 arch/arm/boot/dts/at91-sama5d4_xplained.dts |  3 +-
 arch/arm/boot/dts/at91-sama5d4ek.dts        |  3 +-
 arch/arm/boot/dts/at91rm9200ek.dts          |  4 ++
 arch/arm/boot/dts/at91sam9261ek.dts         |  3 +-
 arch/arm/boot/dts/at91sam9263ek.dts         |  3 +-
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi |  3 +-
 arch/arm/boot/dts/at91sam9m10g45ek.dts      |  3 +-
 arch/arm/boot/dts/at91sam9n12ek.dts         |  3 +-
 arch/arm/boot/dts/at91sam9rl.dtsi           | 15 +++---
 arch/arm/boot/dts/at91sam9rlek.dts          |  7 ++-
 arch/arm/boot/dts/at91sam9x5ek.dtsi         |  3 +-
 arch/arm/boot/dts/sama5d3xcm.dtsi           |  3 +-
 18 files changed, 116 insertions(+), 21 deletions(-)
 create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts

-- 
2.1.4

[PATCH 00/16] AT91 DT for 4.2

[Alexandre Belloni]

Hi,

A dt series for 4.2:
 - Fix at91sam9rl RTC node and use it on at91sam9rlek
 - correct stdout-path for the various kizboxes
 - add stdout-path to the atme evaluation boards
 - add  Acme arietta g25 device tree

Alexandre Belloni (16):
  ARM: at91/dt: at91sam9rl: fix rtc node
  ARM: at91/dt: at91sam9rlek: add RTC
  ARM: at91/dt: kizbox: use stdout-path
  ARM: at91/dt: at91rm9200ek: use stdout-path
  ARM: at91/dt: at91sam9261ek: use stdout-path
  ARM: at91/dt: at91sam9263ek: use stdout-path
  ARM: at91/dt: at91sam9g20ek: use stdout-path
  ARM: at91/dt: at91sam9m10g45ek use stdout-path
  ARM: at91/dt: at91sam9n12ek: use stdout-path
  ARM: at91/dt: at91sam9rlek: use stdout-path
  ARM: at91/dt: at91sam9x5ek: use stdout-path
  ARM: at91/dt: sama5d3xek: use stdout-path
  ARM: at91/dt: sama5d3 xplained: use stdout-path
  ARM: at91/dt: sama5d4ek: use stdout-path
  ARM: at91/dt: sama5d4 xplained: use stdout-path
  ARM: at91/dt: Add Acme Arietta G25

 arch/arm/boot/dts/Makefile                  |  1 +
 arch/arm/boot/dts/at91-acme-arietta.dts     | 75 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/at91-kizbox.dts           |  2 +-
 arch/arm/boot/dts/at91-kizbox2.dts          |  2 +-
 arch/arm/boot/dts/at91-kizboxmini.dts       |  2 +-
 arch/arm/boot/dts/at91-sama5d3_xplained.dts |  2 +-
 arch/arm/boot/dts/at91-sama5d4_xplained.dts |  3 +-
 arch/arm/boot/dts/at91-sama5d4ek.dts        |  3 +-
 arch/arm/boot/dts/at91rm9200ek.dts          |  4 ++
 arch/arm/boot/dts/at91sam9261ek.dts         |  3 +-
 arch/arm/boot/dts/at91sam9263ek.dts         |  3 +-
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi |  3 +-
 arch/arm/boot/dts/at91sam9m10g45ek.dts      |  3 +-
 arch/arm/boot/dts/at91sam9n12ek.dts         |  3 +-
 arch/arm/boot/dts/at91sam9rl.dtsi           | 15 +++---
 arch/arm/boot/dts/at91sam9rlek.dts          |  7 ++-
 arch/arm/boot/dts/at91sam9x5ek.dtsi         |  3 +-
 arch/arm/boot/dts/sama5d3xcm.dtsi           |  3 +-
 18 files changed, 116 insertions(+), 21 deletions(-)
 create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts

-- 
2.1.4

[PATCH 01/16] ARM: at91/dt: at91sam9rl: fix rtc node

[Alexandre Belloni]

The RTC lives at 0xfffffe00. Also reorder the node properly.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rl.dtsi | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index ebfd5ce9cb38..c9920c64791c 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -1065,13 +1065,6 @@
 				};
 			};
 
-			rtc@fffffeb0 {
-				compatible = "atmel,at91rm9200-rtc";
-				reg = <0xfffffeb0 0x40>;
-				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				status = "disabled";
-			};
-
 			rtc@fffffd20 {
 				compatible = "atmel,at91sam9260-rtt";
 				reg = <0xfffffd20 0x10>;
@@ -1085,6 +1078,14 @@
 				reg = <0xfffffd60 0x10>;
 				status = "disabled";
 			};
+
+			rtc@fffffe00 {
+				compatible = "atmel,at91rm9200-rtc";
+				reg = <0xfffffe00 0x40>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				status = "disabled";
+			};
+
 		};
 	};
 
-- 
2.1.4

[PATCH 01/16] ARM: at91/dt: at91sam9rl: fix rtc node

[Alexandre Belloni]

The RTC lives at 0xfffffe00. Also reorder the node properly.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rl.dtsi | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index ebfd5ce9cb38..c9920c64791c 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -1065,13 +1065,6 @@
 				};
 			};
 
-			rtc at fffffeb0 {
-				compatible = "atmel,at91rm9200-rtc";
-				reg = <0xfffffeb0 0x40>;
-				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				status = "disabled";
-			};
-
 			rtc at fffffd20 {
 				compatible = "atmel,at91sam9260-rtt";
 				reg = <0xfffffd20 0x10>;
@@ -1085,6 +1078,14 @@
 				reg = <0xfffffd60 0x10>;
 				status = "disabled";
 			};
+
+			rtc at fffffe00 {
+				compatible = "atmel,at91rm9200-rtc";
+				reg = <0xfffffe00 0x40>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				status = "disabled";
+			};
+
 		};
 	};
 
-- 
2.1.4

[PATCH 02/16] ARM: at91/dt: at91sam9rlek: add RTC

[Alexandre Belloni]

Add RTC support to the at91sam9rlek.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rlek.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
index d9299be3dfe9..724b9f54a60a 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/at91sam9rlek.dts
@@ -184,6 +184,10 @@
 			watchdog@fffffd40 {
 				status = "okay";
 			};
+
+			rtc@fffffe00 {
+				status = "okay";
+			};
 		};
 	};
 
-- 
2.1.4

[PATCH 02/16] ARM: at91/dt: at91sam9rlek: add RTC

[Alexandre Belloni]

Add RTC support to the at91sam9rlek.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rlek.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
index d9299be3dfe9..724b9f54a60a 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/at91sam9rlek.dts
@@ -184,6 +184,10 @@
 			watchdog at fffffd40 {
 				status = "okay";
 			};
+
+			rtc at fffffe00 {
+				status = "okay";
+			};
 		};
 	};
 
-- 
2.1.4

[PATCH 03/16] ARM: at91/dt: kizbox: use stdout-path

[Alexandre Belloni]

The kizbox dts are using the deprecated linux,stdout-path. Replace those by
stdout-path.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Gaël PORTAY <g.portay@overkiz.com>
---
 arch/arm/boot/dts/at91-kizbox.dts     | 2 +-
 arch/arm/boot/dts/at91-kizbox2.dts    | 2 +-
 arch/arm/boot/dts/at91-kizboxmini.dts | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index b567b5ff908f..d9b71065916d 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -16,7 +16,7 @@
 
 	chosen {
 		bootargs = "ubi.mtd=ubi";
-		linux,stdout-path = &dbgu;
+		stdout-path = &dbgu;
 	};
 
 	memory {
diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
index a458e3791bb1..f0b1563cb3f1 100644
--- a/arch/arm/boot/dts/at91-kizbox2.dts
+++ b/arch/arm/boot/dts/at91-kizbox2.dts
@@ -15,7 +15,7 @@
 
 	chosen {
 		bootargs = "ubi.mtd=ubi";
-		linux,stdout-path = &dbgu;
+		stdout-path = &dbgu;
 	};
 
 	memory {
diff --git a/arch/arm/boot/dts/at91-kizboxmini.dts b/arch/arm/boot/dts/at91-kizboxmini.dts
index 4611f227d8d0..9f72b4932634 100644
--- a/arch/arm/boot/dts/at91-kizboxmini.dts
+++ b/arch/arm/boot/dts/at91-kizboxmini.dts
@@ -15,7 +15,7 @@
 
 	chosen {
 		bootargs = "ubi.mtd=ubi";
-		linux,stdout-path = &dbgu;
+		stdout-path = &dbgu;
 	};
 
 	memory {
-- 
2.1.4

[PATCH 03/16] ARM: at91/dt: kizbox: use stdout-path

[Alexandre Belloni]

The kizbox dts are using the deprecated linux,stdout-path. Replace those by
stdout-path.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Ga?l PORTAY <g.portay@overkiz.com>
---
 arch/arm/boot/dts/at91-kizbox.dts     | 2 +-
 arch/arm/boot/dts/at91-kizbox2.dts    | 2 +-
 arch/arm/boot/dts/at91-kizboxmini.dts | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index b567b5ff908f..d9b71065916d 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -16,7 +16,7 @@
 
 	chosen {
 		bootargs = "ubi.mtd=ubi";
-		linux,stdout-path = &dbgu;
+		stdout-path = &dbgu;
 	};
 
 	memory {
diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
index a458e3791bb1..f0b1563cb3f1 100644
--- a/arch/arm/boot/dts/at91-kizbox2.dts
+++ b/arch/arm/boot/dts/at91-kizbox2.dts
@@ -15,7 +15,7 @@
 
 	chosen {
 		bootargs = "ubi.mtd=ubi";
-		linux,stdout-path = &dbgu;
+		stdout-path = &dbgu;
 	};
 
 	memory {
diff --git a/arch/arm/boot/dts/at91-kizboxmini.dts b/arch/arm/boot/dts/at91-kizboxmini.dts
index 4611f227d8d0..9f72b4932634 100644
--- a/arch/arm/boot/dts/at91-kizboxmini.dts
+++ b/arch/arm/boot/dts/at91-kizboxmini.dts
@@ -15,7 +15,7 @@
 
 	chosen {
 		bootargs = "ubi.mtd=ubi";
-		linux,stdout-path = &dbgu;
+		stdout-path = &dbgu;
 	};
 
 	memory {
-- 
2.1.4

[PATCH 04/16] ARM: at91/dt: at91rm9200ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91rm9200ek.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
index 2a5d21247d7e..8dab4b75ca97 100644
--- a/arch/arm/boot/dts/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/at91rm9200ek.dts
@@ -12,6 +12,10 @@
 	model = "Atmel AT91RM9200 evaluation kit";
 	compatible = "atmel,at91rm9200ek", "atmel,at91rm9200";
 
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	memory {
 		reg = <0x20000000 0x4000000>;
 	};
-- 
2.1.4

[PATCH 04/16] ARM: at91/dt: at91rm9200ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91rm9200ek.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
index 2a5d21247d7e..8dab4b75ca97 100644
--- a/arch/arm/boot/dts/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/at91rm9200ek.dts
@@ -12,6 +12,10 @@
 	model = "Atmel AT91RM9200 evaluation kit";
 	compatible = "atmel,at91rm9200ek", "atmel,at91rm9200";
 
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	memory {
 		reg = <0x20000000 0x4000000>;
 	};
-- 
2.1.4

[PATCH 05/16] ARM: at91/dt: at91sam9261ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9261ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts
index f4a765729c7a..2e92ac020f23 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/at91sam9261ek.dts
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
+		bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 05/16] ARM: at91/dt: at91sam9261ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9261ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts
index f4a765729c7a..2e92ac020f23 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/at91sam9261ek.dts
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
+		bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 06/16] ARM: at91/dt: at91sam9263ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9263ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 5cf93eecd8f1..23381276ffb8 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9263ek", "atmel,at91sam9263", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 06/16] ARM: at91/dt: at91sam9263ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9263ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 5cf93eecd8f1..23381276ffb8 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9263ek", "atmel,at91sam9263", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 07/16] ARM: at91/dt: at91sam9g20ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index dfaacb113f2e..57548a2c5a1e 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -10,7 +10,8 @@
 / {
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 07/16] ARM: at91/dt: at91sam9g20ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index dfaacb113f2e..57548a2c5a1e 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -10,7 +10,8 @@
 / {
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 08/16] ARM: at91/dt: at91sam9m10g45ek use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9m10g45ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 33ce7ca2c404..1375d3362603 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -15,7 +15,8 @@
 	compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
+		bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 08/16] ARM: at91/dt: at91sam9m10g45ek use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9m10g45ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 33ce7ca2c404..1375d3362603 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -15,7 +15,8 @@
 	compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
+		bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 09/16] ARM: at91/dt: at91sam9n12ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9n12ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index 6e067c8a3502..eab17fcace6d 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -14,7 +14,8 @@
 	compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 09/16] ARM: at91/dt: at91sam9n12ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9n12ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index 6e067c8a3502..eab17fcace6d 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -14,7 +14,8 @@
 	compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 10/16] ARM: at91/dt: at91sam9rlek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rlek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
index 724b9f54a60a..558c9f220bed 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/at91sam9rlek.dts
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9rlek", "atmel,at91sam9rl", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+		bootargs = "rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 10/16] ARM: at91/dt: at91sam9rlek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rlek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
index 724b9f54a60a..558c9f220bed 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/at91sam9rlek.dts
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9rlek", "atmel,at91sam9rl", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+		bootargs = "rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 11/16] ARM: at91/dt: at91sam9x5ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9x5ek.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi
index cc83a37a7311..d237c462dfc6 100644
--- a/arch/arm/boot/dts/at91sam9x5ek.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	ahb {
-- 
2.1.4

[PATCH 11/16] ARM: at91/dt: at91sam9x5ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9x5ek.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi
index cc83a37a7311..d237c462dfc6 100644
--- a/arch/arm/boot/dts/at91sam9x5ek.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi
@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	ahb {
-- 
2.1.4

[PATCH 12/16] ARM: at91/dt: sama5d3xek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3xcm.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
index ef404e907026..2cf9c3611db6 100644
--- a/arch/arm/boot/dts/sama5d3xcm.dtsi
+++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
@@ -11,7 +11,8 @@
 	compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+		bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 12/16] ARM: at91/dt: sama5d3xek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3xcm.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
index ef404e907026..2cf9c3611db6 100644
--- a/arch/arm/boot/dts/sama5d3xcm.dtsi
+++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
@@ -11,7 +11,8 @@
 	compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+		bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 13/16] ARM: at91/dt: sama5d3 xplained: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the bootargs.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d3_xplained.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index 4799e88cdf5e..d81474e0bcd6 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -14,7 +14,7 @@
 	compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 13/16] ARM: at91/dt: sama5d3 xplained: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the bootargs.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d3_xplained.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index 4799e88cdf5e..d81474e0bcd6 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -14,7 +14,7 @@
 	compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 14/16] ARM: at91/dt: sama5d4ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
index 89ef4a540db5..c8be7f82cf8c 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
@@ -50,7 +50,8 @@
 	compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+		bootargs = "ignore_loglevel earlyprintk";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 14/16] ARM: at91/dt: sama5d4ek: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4ek.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
index 89ef4a540db5..c8be7f82cf8c 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
@@ -50,7 +50,8 @@
 	compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+		bootargs = "ignore_loglevel earlyprintk";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 15/16] ARM: at91/dt: sama5d4 xplained: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4_xplained.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index 5dbc0fcfc5a8..22ad7c959103 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -50,7 +50,8 @@
 	compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+		bootargs = "ignore_loglevel earlyprintk";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 15/16] ARM: at91/dt: sama5d4 xplained: use stdout-path

[Alexandre Belloni]

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4_xplained.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index 5dbc0fcfc5a8..22ad7c959103 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -50,7 +50,8 @@
 	compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+		bootargs = "ignore_loglevel earlyprintk";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
-- 
2.1.4

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Alexandre Belloni]

Add a minimum Device Tree for Acme Arietta G25.
http://acme.systems/arietta

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
---
 arch/arm/boot/dts/Makefile              |  1 +
 arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
 2 files changed, 76 insertions(+)
 create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8c3da289a00b..96a169e6ea56 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
 	at91sam9n12ek.dtb \
 	at91sam9rlek.dtb \
 	at91-ariag25.dtb \
+	at91-acme-arietta.dtb \
 	at91-cosino_mega2560.dtb \
 	at91-kizboxmini.dtb \
 	at91sam9g15ek.dtb \
diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
new file mode 100644
index 000000000000..142d588ad6bf
--- /dev/null
+++ b/arch/arm/boot/dts/at91-acme-arietta.dts
@@ -0,0 +1,75 @@
+/*
+ * Device Tree file for Arietta G25
+ * This device tree is minimal, to activate more peripherals, see:
+ * http://dts.acmesystems.it/arietta/
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+/ {
+	model = "Acme Systems Arietta G25";
+	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+				  &pinctrl_mmc0_slot0_clk_cmd_dat0
+				  &pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			usb2: gadget@f803c000 {
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@00600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci@00700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		arietta_led {
+			label = "arietta_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
-- 
2.1.4

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Alexandre Belloni]

Add a minimum Device Tree for Acme Arietta G25.
http://acme.systems/arietta

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
---
 arch/arm/boot/dts/Makefile              |  1 +
 arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
 2 files changed, 76 insertions(+)
 create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8c3da289a00b..96a169e6ea56 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
 	at91sam9n12ek.dtb \
 	at91sam9rlek.dtb \
 	at91-ariag25.dtb \
+	at91-acme-arietta.dtb \
 	at91-cosino_mega2560.dtb \
 	at91-kizboxmini.dtb \
 	at91sam9g15ek.dtb \
diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
new file mode 100644
index 000000000000..142d588ad6bf
--- /dev/null
+++ b/arch/arm/boot/dts/at91-acme-arietta.dts
@@ -0,0 +1,75 @@
+/*
+ * Device Tree file for Arietta G25
+ * This device tree is minimal, to activate more peripherals, see:
+ * http://dts.acmesystems.it/arietta/
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+/ {
+	model = "Acme Systems Arietta G25";
+	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc at f0008000 {
+				pinctrl-0 = <
+				  &pinctrl_mmc0_slot0_clk_cmd_dat0
+				  &pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			usb2: gadget at f803c000 {
+				status = "okay";
+			};
+
+			dbgu: serial at fffff200 {
+				status = "okay";
+			};
+
+			rtc at fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci at 00600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci at 00700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		arietta_led {
+			label = "arietta_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
-- 
2.1.4

Re: [PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Sergio Tanzilli]

Great Alex

thanks

Sergio

On 29 May 2015 at 19:47, Alexandre Belloni
<alexandre.belloni@free-electrons.com> wrote:
> Add a minimum Device Tree for Acme Arietta G25.
> http://acme.systems/arietta
>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
> ---
>  arch/arm/boot/dts/Makefile              |  1 +
>  arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
>  2 files changed, 76 insertions(+)
>  create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8c3da289a00b..96a169e6ea56 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
>         at91sam9n12ek.dtb \
>         at91sam9rlek.dtb \
>         at91-ariag25.dtb \
> +       at91-acme-arietta.dtb \
>         at91-cosino_mega2560.dtb \
>         at91-kizboxmini.dtb \
>         at91sam9g15ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
> new file mode 100644
> index 000000000000..142d588ad6bf
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-acme-arietta.dts
> @@ -0,0 +1,75 @@
> +/*
> + * Device Tree file for Arietta G25
> + * This device tree is minimal, to activate more peripherals, see:
> + * http://dts.acmesystems.it/arietta/
> + */
> +/dts-v1/;
> +#include "at91sam9g25.dtsi"
> +/ {
> +       model = "Acme Systems Arietta G25";
> +       compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       memory {
> +               reg = <0x20000000 0x8000000>;
> +       };
> +
> +       clocks {
> +               slow_xtal {
> +                       clock-frequency = <32768>;
> +               };
> +
> +               main_xtal {
> +                       clock-frequency = <12000000>;
> +               };
> +       };
> +
> +       ahb {
> +               apb {
> +                       mmc0: mmc@f0008000 {
> +                               pinctrl-0 = <
> +                                 &pinctrl_mmc0_slot0_clk_cmd_dat0
> +                                 &pinctrl_mmc0_slot0_dat1_3>;
> +                               status = "okay";
> +
> +                               slot@0 {
> +                                       reg = <0>;
> +                                       bus-width = <4>;
> +                               };
> +                       };
> +
> +                       usb2: gadget@f803c000 {
> +                               status = "okay";
> +                       };
> +
> +                       dbgu: serial@fffff200 {
> +                               status = "okay";
> +                       };
> +
> +                       rtc@fffffeb0 {
> +                               status = "okay";
> +                       };
> +               };
> +
> +               usb0: ohci@00600000 {
> +                       status = "okay";
> +                       num-ports = <3>;
> +               };
> +
> +               usb1: ehci@00700000 {
> +                       status = "okay";
> +               };
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +               arietta_led {
> +                       label = "arietta_led";
> +                       gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
> +                       linux,default-trigger = "heartbeat";
> +               };
> +       };
> +};
> --
> 2.1.4
>



-- 
Sergio Tanzilli
tanzilli@acmesystems.it
Acme Systems srl
http://www.acmesystems.it

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Sergio Tanzilli]

Great Alex

thanks

Sergio

On 29 May 2015 at 19:47, Alexandre Belloni
<alexandre.belloni@free-electrons.com> wrote:
> Add a minimum Device Tree for Acme Arietta G25.
> http://acme.systems/arietta
>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
> ---
>  arch/arm/boot/dts/Makefile              |  1 +
>  arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
>  2 files changed, 76 insertions(+)
>  create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8c3da289a00b..96a169e6ea56 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
>         at91sam9n12ek.dtb \
>         at91sam9rlek.dtb \
>         at91-ariag25.dtb \
> +       at91-acme-arietta.dtb \
>         at91-cosino_mega2560.dtb \
>         at91-kizboxmini.dtb \
>         at91sam9g15ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
> new file mode 100644
> index 000000000000..142d588ad6bf
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-acme-arietta.dts
> @@ -0,0 +1,75 @@
> +/*
> + * Device Tree file for Arietta G25
> + * This device tree is minimal, to activate more peripherals, see:
> + * http://dts.acmesystems.it/arietta/
> + */
> +/dts-v1/;
> +#include "at91sam9g25.dtsi"
> +/ {
> +       model = "Acme Systems Arietta G25";
> +       compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       memory {
> +               reg = <0x20000000 0x8000000>;
> +       };
> +
> +       clocks {
> +               slow_xtal {
> +                       clock-frequency = <32768>;
> +               };
> +
> +               main_xtal {
> +                       clock-frequency = <12000000>;
> +               };
> +       };
> +
> +       ahb {
> +               apb {
> +                       mmc0: mmc at f0008000 {
> +                               pinctrl-0 = <
> +                                 &pinctrl_mmc0_slot0_clk_cmd_dat0
> +                                 &pinctrl_mmc0_slot0_dat1_3>;
> +                               status = "okay";
> +
> +                               slot at 0 {
> +                                       reg = <0>;
> +                                       bus-width = <4>;
> +                               };
> +                       };
> +
> +                       usb2: gadget at f803c000 {
> +                               status = "okay";
> +                       };
> +
> +                       dbgu: serial at fffff200 {
> +                               status = "okay";
> +                       };
> +
> +                       rtc at fffffeb0 {
> +                               status = "okay";
> +                       };
> +               };
> +
> +               usb0: ohci at 00600000 {
> +                       status = "okay";
> +                       num-ports = <3>;
> +               };
> +
> +               usb1: ehci at 00700000 {
> +                       status = "okay";
> +               };
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +               arietta_led {
> +                       label = "arietta_led";
> +                       gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
> +                       linux,default-trigger = "heartbeat";
> +               };
> +       };
> +};
> --
> 2.1.4
>



-- 
Sergio Tanzilli
tanzilli at acmesystems.it
Acme Systems srl
http://www.acmesystems.it

Re: [PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Nicolas Ferre]

Le 29/05/2015 19:47, Alexandre Belloni a écrit :
> Add a minimum Device Tree for Acme Arietta G25.
> http://acme.systems/arietta
> 
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
> ---
>  arch/arm/boot/dts/Makefile              |  1 +
>  arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
>  2 files changed, 76 insertions(+)
>  create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8c3da289a00b..96a169e6ea56 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
>  	at91sam9n12ek.dtb \
>  	at91sam9rlek.dtb \
>  	at91-ariag25.dtb \
> +	at91-acme-arietta.dtb \

Do you want to have the additional vendor name here? We already have 2
boards by ACME and they don't have this type of name:
at91-foxg20.dtb
at91-ariag25.dtb

So I'd prefer to use "at91-arietta.dtb" or "at91-ariettag25.dtb" or any
kind or variant from these ones... I know it may come from the ACME DT
generator tool, but it could be strange at first sight.

Sergio, do you have an opinion? In relation with eventual future
products, which is your preferred name?


>  	at91-cosino_mega2560.dtb \
>  	at91-kizboxmini.dtb \
>  	at91sam9g15ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
> new file mode 100644
> index 000000000000..142d588ad6bf
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-acme-arietta.dts
> @@ -0,0 +1,75 @@
> +/*
> + * Device Tree file for Arietta G25
> + * This device tree is minimal, to activate more peripherals, see:
> + * http://dts.acmesystems.it/arietta/

Yes, absolutely: link to the DT generator is a big plus here.


> + */
> +/dts-v1/;
> +#include "at91sam9g25.dtsi"
> +/ {
> +	model = "Acme Systems Arietta G25";
> +	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
> +

Don't we need to add a "alias" group here, to be sure that the
"stdout-path" is always good whatever appends to the underlying
at91sam9g25.dtsi (nitpicking, I know ;-)) ?

> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory {
> +		reg = <0x20000000 0x8000000>;
> +	};
> +
> +	clocks {
> +		slow_xtal {
> +			clock-frequency = <32768>;
> +		};
> +
> +		main_xtal {
> +			clock-frequency = <12000000>;
> +		};
> +	};
> +
> +	ahb {
> +		apb {
> +			mmc0: mmc@f0008000 {
> +				pinctrl-0 = <
> +				  &pinctrl_mmc0_slot0_clk_cmd_dat0
> +				  &pinctrl_mmc0_slot0_dat1_3>;
> +				status = "okay";
> +
> +				slot@0 {
> +					reg = <0>;
> +					bus-width = <4>;
> +				};
> +			};
> +
> +			usb2: gadget@f803c000 {
> +				status = "okay";
> +			};
> +
> +			dbgu: serial@fffff200 {
> +				status = "okay";
> +			};
> +
> +			rtc@fffffeb0 {
> +				status = "okay";
> +			};
> +		};
> +
> +		usb0: ohci@00600000 {
> +			status = "okay";
> +			num-ports = <3>;
> +		};
> +
> +		usb1: ehci@00700000 {
> +			status = "okay";
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		arietta_led {
> +			label = "arietta_led";
> +			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +};
> 


-- 
Nicolas Ferre

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Nicolas Ferre]

Le 29/05/2015 19:47, Alexandre Belloni a ?crit :
> Add a minimum Device Tree for Acme Arietta G25.
> http://acme.systems/arietta
> 
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
> ---
>  arch/arm/boot/dts/Makefile              |  1 +
>  arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
>  2 files changed, 76 insertions(+)
>  create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8c3da289a00b..96a169e6ea56 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
>  	at91sam9n12ek.dtb \
>  	at91sam9rlek.dtb \
>  	at91-ariag25.dtb \
> +	at91-acme-arietta.dtb \

Do you want to have the additional vendor name here? We already have 2
boards by ACME and they don't have this type of name:
at91-foxg20.dtb
at91-ariag25.dtb

So I'd prefer to use "at91-arietta.dtb" or "at91-ariettag25.dtb" or any
kind or variant from these ones... I know it may come from the ACME DT
generator tool, but it could be strange at first sight.

Sergio, do you have an opinion? In relation with eventual future
products, which is your preferred name?


>  	at91-cosino_mega2560.dtb \
>  	at91-kizboxmini.dtb \
>  	at91sam9g15ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
> new file mode 100644
> index 000000000000..142d588ad6bf
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-acme-arietta.dts
> @@ -0,0 +1,75 @@
> +/*
> + * Device Tree file for Arietta G25
> + * This device tree is minimal, to activate more peripherals, see:
> + * http://dts.acmesystems.it/arietta/

Yes, absolutely: link to the DT generator is a big plus here.


> + */
> +/dts-v1/;
> +#include "at91sam9g25.dtsi"
> +/ {
> +	model = "Acme Systems Arietta G25";
> +	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
> +

Don't we need to add a "alias" group here, to be sure that the
"stdout-path" is always good whatever appends to the underlying
at91sam9g25.dtsi (nitpicking, I know ;-)) ?

> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory {
> +		reg = <0x20000000 0x8000000>;
> +	};
> +
> +	clocks {
> +		slow_xtal {
> +			clock-frequency = <32768>;
> +		};
> +
> +		main_xtal {
> +			clock-frequency = <12000000>;
> +		};
> +	};
> +
> +	ahb {
> +		apb {
> +			mmc0: mmc at f0008000 {
> +				pinctrl-0 = <
> +				  &pinctrl_mmc0_slot0_clk_cmd_dat0
> +				  &pinctrl_mmc0_slot0_dat1_3>;
> +				status = "okay";
> +
> +				slot at 0 {
> +					reg = <0>;
> +					bus-width = <4>;
> +				};
> +			};
> +
> +			usb2: gadget at f803c000 {
> +				status = "okay";
> +			};
> +
> +			dbgu: serial at fffff200 {
> +				status = "okay";
> +			};
> +
> +			rtc at fffffeb0 {
> +				status = "okay";
> +			};
> +		};
> +
> +		usb0: ohci at 00600000 {
> +			status = "okay";
> +			num-ports = <3>;
> +		};
> +
> +		usb1: ehci at 00700000 {
> +			status = "okay";
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		arietta_led {
> +			label = "arietta_led";
> +			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +};
> 


-- 
Nicolas Ferre

Re: [PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Sergio Tanzilli]

Hi Nicolas

at91-ariettag25.dtb is ok for me. I'll change the name on DT generator.


at91-ariettag25.dtb is better than at91-arietta.dtb because probably
we'll exit with different Atmel cpu on arietta very soon

thanks

Sergio


On 1 June 2015 at 18:18, Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
> Le 29/05/2015 19:47, Alexandre Belloni a écrit :
>> Add a minimum Device Tree for Acme Arietta G25.
>> http://acme.systems/arietta
>>
>> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
>> Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
>> ---
>>  arch/arm/boot/dts/Makefile              |  1 +
>>  arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
>>  2 files changed, 76 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 8c3da289a00b..96a169e6ea56 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
>>       at91sam9n12ek.dtb \
>>       at91sam9rlek.dtb \
>>       at91-ariag25.dtb \
>> +     at91-acme-arietta.dtb \
>
> Do you want to have the additional vendor name here? We already have 2
> boards by ACME and they don't have this type of name:
> at91-foxg20.dtb
> at91-ariag25.dtb
>
> So I'd prefer to use "at91-arietta.dtb" or "at91-ariettag25.dtb" or any
> kind or variant from these ones... I know it may come from the ACME DT
> generator tool, but it could be strange at first sight.
>
> Sergio, do you have an opinion? In relation with eventual future
> products, which is your preferred name?
>
>
>>       at91-cosino_mega2560.dtb \
>>       at91-kizboxmini.dtb \
>>       at91sam9g15ek.dtb \
>> diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
>> new file mode 100644
>> index 000000000000..142d588ad6bf
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91-acme-arietta.dts
>> @@ -0,0 +1,75 @@
>> +/*
>> + * Device Tree file for Arietta G25
>> + * This device tree is minimal, to activate more peripherals, see:
>> + * http://dts.acmesystems.it/arietta/
>
> Yes, absolutely: link to the DT generator is a big plus here.
>
>
>> + */
>> +/dts-v1/;
>> +#include "at91sam9g25.dtsi"
>> +/ {
>> +     model = "Acme Systems Arietta G25";
>> +     compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
>> +
>
> Don't we need to add a "alias" group here, to be sure that the
> "stdout-path" is always good whatever appends to the underlying
> at91sam9g25.dtsi (nitpicking, I know ;-)) ?
>
>> +     chosen {
>> +             stdout-path = "serial0:115200n8";
>> +     };
>> +
>> +     memory {
>> +             reg = <0x20000000 0x8000000>;
>> +     };
>> +
>> +     clocks {
>> +             slow_xtal {
>> +                     clock-frequency = <32768>;
>> +             };
>> +
>> +             main_xtal {
>> +                     clock-frequency = <12000000>;
>> +             };
>> +     };
>> +
>> +     ahb {
>> +             apb {
>> +                     mmc0: mmc@f0008000 {
>> +                             pinctrl-0 = <
>> +                               &pinctrl_mmc0_slot0_clk_cmd_dat0
>> +                               &pinctrl_mmc0_slot0_dat1_3>;
>> +                             status = "okay";
>> +
>> +                             slot@0 {
>> +                                     reg = <0>;
>> +                                     bus-width = <4>;
>> +                             };
>> +                     };
>> +
>> +                     usb2: gadget@f803c000 {
>> +                             status = "okay";
>> +                     };
>> +
>> +                     dbgu: serial@fffff200 {
>> +                             status = "okay";
>> +                     };
>> +
>> +                     rtc@fffffeb0 {
>> +                             status = "okay";
>> +                     };
>> +             };
>> +
>> +             usb0: ohci@00600000 {
>> +                     status = "okay";
>> +                     num-ports = <3>;
>> +             };
>> +
>> +             usb1: ehci@00700000 {
>> +                     status = "okay";
>> +             };
>> +     };
>> +
>> +     leds {
>> +             compatible = "gpio-leds";
>> +             arietta_led {
>> +                     label = "arietta_led";
>> +                     gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
>> +                     linux,default-trigger = "heartbeat";
>> +             };
>> +     };
>> +};
>>
>
>
> --
> Nicolas Ferre



-- 
Sergio Tanzilli
tanzilli@acmesystems.it
Acme Systems srl
http://www.acmesystems.it

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Sergio Tanzilli]

Hi Nicolas

at91-ariettag25.dtb is ok for me. I'll change the name on DT generator.


at91-ariettag25.dtb is better than at91-arietta.dtb because probably
we'll exit with different Atmel cpu on arietta very soon

thanks

Sergio


On 1 June 2015 at 18:18, Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
> Le 29/05/2015 19:47, Alexandre Belloni a ?crit :
>> Add a minimum Device Tree for Acme Arietta G25.
>> http://acme.systems/arietta
>>
>> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
>> Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
>> ---
>>  arch/arm/boot/dts/Makefile              |  1 +
>>  arch/arm/boot/dts/at91-acme-arietta.dts | 75 +++++++++++++++++++++++++++++++++
>>  2 files changed, 76 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/at91-acme-arietta.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 8c3da289a00b..96a169e6ea56 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -31,6 +31,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
>>       at91sam9n12ek.dtb \
>>       at91sam9rlek.dtb \
>>       at91-ariag25.dtb \
>> +     at91-acme-arietta.dtb \
>
> Do you want to have the additional vendor name here? We already have 2
> boards by ACME and they don't have this type of name:
> at91-foxg20.dtb
> at91-ariag25.dtb
>
> So I'd prefer to use "at91-arietta.dtb" or "at91-ariettag25.dtb" or any
> kind or variant from these ones... I know it may come from the ACME DT
> generator tool, but it could be strange at first sight.
>
> Sergio, do you have an opinion? In relation with eventual future
> products, which is your preferred name?
>
>
>>       at91-cosino_mega2560.dtb \
>>       at91-kizboxmini.dtb \
>>       at91sam9g15ek.dtb \
>> diff --git a/arch/arm/boot/dts/at91-acme-arietta.dts b/arch/arm/boot/dts/at91-acme-arietta.dts
>> new file mode 100644
>> index 000000000000..142d588ad6bf
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91-acme-arietta.dts
>> @@ -0,0 +1,75 @@
>> +/*
>> + * Device Tree file for Arietta G25
>> + * This device tree is minimal, to activate more peripherals, see:
>> + * http://dts.acmesystems.it/arietta/
>
> Yes, absolutely: link to the DT generator is a big plus here.
>
>
>> + */
>> +/dts-v1/;
>> +#include "at91sam9g25.dtsi"
>> +/ {
>> +     model = "Acme Systems Arietta G25";
>> +     compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
>> +
>
> Don't we need to add a "alias" group here, to be sure that the
> "stdout-path" is always good whatever appends to the underlying
> at91sam9g25.dtsi (nitpicking, I know ;-)) ?
>
>> +     chosen {
>> +             stdout-path = "serial0:115200n8";
>> +     };
>> +
>> +     memory {
>> +             reg = <0x20000000 0x8000000>;
>> +     };
>> +
>> +     clocks {
>> +             slow_xtal {
>> +                     clock-frequency = <32768>;
>> +             };
>> +
>> +             main_xtal {
>> +                     clock-frequency = <12000000>;
>> +             };
>> +     };
>> +
>> +     ahb {
>> +             apb {
>> +                     mmc0: mmc at f0008000 {
>> +                             pinctrl-0 = <
>> +                               &pinctrl_mmc0_slot0_clk_cmd_dat0
>> +                               &pinctrl_mmc0_slot0_dat1_3>;
>> +                             status = "okay";
>> +
>> +                             slot at 0 {
>> +                                     reg = <0>;
>> +                                     bus-width = <4>;
>> +                             };
>> +                     };
>> +
>> +                     usb2: gadget at f803c000 {
>> +                             status = "okay";
>> +                     };
>> +
>> +                     dbgu: serial at fffff200 {
>> +                             status = "okay";
>> +                     };
>> +
>> +                     rtc at fffffeb0 {
>> +                             status = "okay";
>> +                     };
>> +             };
>> +
>> +             usb0: ohci at 00600000 {
>> +                     status = "okay";
>> +                     num-ports = <3>;
>> +             };
>> +
>> +             usb1: ehci at 00700000 {
>> +                     status = "okay";
>> +             };
>> +     };
>> +
>> +     leds {
>> +             compatible = "gpio-leds";
>> +             arietta_led {
>> +                     label = "arietta_led";
>> +                     gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
>> +                     linux,default-trigger = "heartbeat";
>> +             };
>> +     };
>> +};
>>
>
>
> --
> Nicolas Ferre



-- 
Sergio Tanzilli
tanzilli at acmesystems.it
Acme Systems srl
http://www.acmesystems.it

Re: [PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Alexandre Belloni]

On 01/06/2015 at 18:26:42 +0200, Sergio Tanzilli wrote :
> Hi Nicolas
> 
> at91-ariettag25.dtb is ok for me. I'll change the name on DT generator.
> 
> 
> at91-ariettag25.dtb is better than at91-arietta.dtb because probably
> we'll exit with different Atmel cpu on arietta very soon
> 

Ok, I was wondering about that. I'll rename.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Alexandre Belloni]

On 01/06/2015 at 18:26:42 +0200, Sergio Tanzilli wrote :
> Hi Nicolas
> 
> at91-ariettag25.dtb is ok for me. I'll change the name on DT generator.
> 
> 
> at91-ariettag25.dtb is better than at91-arietta.dtb because probably
> we'll exit with different Atmel cpu on arietta very soon
> 

Ok, I was wondering about that. I'll rename.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Re: [PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Alexandre Belloni]

On 01/06/2015 at 18:18:46 +0200, Nicolas Ferre wrote :
> > + */
> > +/dts-v1/;
> > +#include "at91sam9g25.dtsi"
> > +/ {
> > +	model = "Acme Systems Arietta G25";
> > +	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
> > +
> 
> Don't we need to add a "alias" group here, to be sure that the
> "stdout-path" is always good whatever appends to the underlying
> at91sam9g25.dtsi (nitpicking, I know ;-)) ?
> 

I've just checked and dtc seems to be doing the right thing, I'll do
that.

> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +
> > +	memory {
> > +		reg = <0x20000000 0x8000000>;
> > +	};
> > +
> > +	clocks {
> > +		slow_xtal {
> > +			clock-frequency = <32768>;
> > +		};
> > +
> > +		main_xtal {
> > +			clock-frequency = <12000000>;
> > +		};
> > +	};
> > +
> > +	ahb {
> > +		apb {
> > +			mmc0: mmc@f0008000 {
> > +				pinctrl-0 = <
> > +				  &pinctrl_mmc0_slot0_clk_cmd_dat0
> > +				  &pinctrl_mmc0_slot0_dat1_3>;
> > +				status = "okay";
> > +
> > +				slot@0 {
> > +					reg = <0>;
> > +					bus-width = <4>;
> > +				};
> > +			};
> > +
> > +			usb2: gadget@f803c000 {
> > +				status = "okay";
> > +			};
> > +
> > +			dbgu: serial@fffff200 {
> > +				status = "okay";
> > +			};
> > +
> > +			rtc@fffffeb0 {
> > +				status = "okay";
> > +			};
> > +		};
> > +
> > +		usb0: ohci@00600000 {
> > +			status = "okay";
> > +			num-ports = <3>;
> > +		};
> > +
> > +		usb1: ehci@00700000 {
> > +			status = "okay";
> > +		};
> > +	};
> > +
> > +	leds {
> > +		compatible = "gpio-leds";
> > +		arietta_led {
> > +			label = "arietta_led";
> > +			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
> > +			linux,default-trigger = "heartbeat";
> > +		};
> > +	};
> > +};
> > 
> 
> 
> -- 
> Nicolas Ferre

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 16/16] ARM: at91/dt: Add Acme Arietta G25

[Alexandre Belloni]

On 01/06/2015 at 18:18:46 +0200, Nicolas Ferre wrote :
> > + */
> > +/dts-v1/;
> > +#include "at91sam9g25.dtsi"
> > +/ {
> > +	model = "Acme Systems Arietta G25";
> > +	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
> > +
> 
> Don't we need to add a "alias" group here, to be sure that the
> "stdout-path" is always good whatever appends to the underlying
> at91sam9g25.dtsi (nitpicking, I know ;-)) ?
> 

I've just checked and dtc seems to be doing the right thing, I'll do
that.

> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +
> > +	memory {
> > +		reg = <0x20000000 0x8000000>;
> > +	};
> > +
> > +	clocks {
> > +		slow_xtal {
> > +			clock-frequency = <32768>;
> > +		};
> > +
> > +		main_xtal {
> > +			clock-frequency = <12000000>;
> > +		};
> > +	};
> > +
> > +	ahb {
> > +		apb {
> > +			mmc0: mmc at f0008000 {
> > +				pinctrl-0 = <
> > +				  &pinctrl_mmc0_slot0_clk_cmd_dat0
> > +				  &pinctrl_mmc0_slot0_dat1_3>;
> > +				status = "okay";
> > +
> > +				slot at 0 {
> > +					reg = <0>;
> > +					bus-width = <4>;
> > +				};
> > +			};
> > +
> > +			usb2: gadget at f803c000 {
> > +				status = "okay";
> > +			};
> > +
> > +			dbgu: serial at fffff200 {
> > +				status = "okay";
> > +			};
> > +
> > +			rtc at fffffeb0 {
> > +				status = "okay";
> > +			};
> > +		};
> > +
> > +		usb0: ohci at 00600000 {
> > +			status = "okay";
> > +			num-ports = <3>;
> > +		};
> > +
> > +		usb1: ehci at 00700000 {
> > +			status = "okay";
> > +		};
> > +	};
> > +
> > +	leds {
> > +		compatible = "gpio-leds";
> > +		arietta_led {
> > +			label = "arietta_led";
> > +			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
> > +			linux,default-trigger = "heartbeat";
> > +		};
> > +	};
> > +};
> > 
> 
> 
> -- 
> Nicolas Ferre

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com