* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Hi Simon, Magnus,
The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
A1 (r8a7740) multi-platform kernels.
Lacking areas are:
- USB (it does't work in legacy, neither),
- HDMI on armadillo (it doesn't work in legacy, neither),
- Camera on armadillo (we don't care),
- LCDC:
- on armadillo, this is supported by the board staging code,
- on kzm9g, the LCDC is wired to the legacy INTC, which is not
planned to be supported with DT,
- DMAC/IPMMU (no DT bindings are planned).
Hence this patch series removes legacy board and SoC code for
sh73a0/kzm9g and r8a7740/armadillo.
It consists of 4 parts:
- Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
dtb) and sh73a0,
- Patches 5-8 remove legacy support for armadillo (board code,
defconfig, dtb) and r8a7740,
- Patches 9-11 remove generic shmobile support code (dma-register.h,
legacy PM Domains, zboot) that became unused by the removal of
legacy sh73a0/kzm9g and r8a7740/armadillo,
- Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
pinctrl drivers.
Dependencies:
- This is against next-20150617,
- To keep up with existing LCDC functionality for armadillo-legacy,
the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
0/7] staging: board: armadillo800eva: Board staging for
sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
However, it can be applied as-is now, and board staging can he
handled in parallel (if at all).
Thanks for applying!
Geert Uytterhoeven (15):
ARM: shmobile: Remove legacy board code for KZM-A9-GT
ARM: shmobile: Remove legacy kzm9g_defconfig
ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
ARM: shmobile: Remove legacy armadillo800eva_defconfig
ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
ARM: shmobile: Remove legacy SoC code for R-Mobile A1
ARM: shmobile: Remove unused dma-register.h
ARM: shmobile: R-Mobile: Remove legacy PM Domain code
ARM: shmobile: Remove obsolete zboot support
pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
MAINTAINERS | 2 -
arch/arm/boot/compressed/Makefile | 4 -
arch/arm/boot/compressed/head-shmobile.S | 71 -
arch/arm/boot/dts/Makefile | 4 +-
arch/arm/configs/armadillo800eva_defconfig | 162 ---
arch/arm/configs/kzm9g_defconfig | 154 ---
arch/arm/mach-shmobile/Kconfig | 33 -
arch/arm/mach-shmobile/Makefile | 8 +-
arch/arm/mach-shmobile/Makefile.boot | 2 -
arch/arm/mach-shmobile/board-armadillo800eva.c | 1365 --------------------
arch/arm/mach-shmobile/board-kzm9g.c | 916 -------------
arch/arm/mach-shmobile/clock-r8a7740.c | 675 ----------
arch/arm/mach-shmobile/clock-sh73a0.c | 752 -----------
arch/arm/mach-shmobile/dma-register.h | 84 --
arch/arm/mach-shmobile/include/mach/head-kzm9g.txt | 410 ------
arch/arm/mach-shmobile/include/mach/zboot.h | 19 -
arch/arm/mach-shmobile/include/mach/zboot_macros.h | 108 --
arch/arm/mach-shmobile/intc-sh73a0.c | 337 -----
arch/arm/mach-shmobile/pm-r8a7740.c | 129 --
arch/arm/mach-shmobile/pm-rmobile.c | 39 -
arch/arm/mach-shmobile/pm-rmobile.h | 24 -
arch/arm/mach-shmobile/pm-sh73a0.c | 32 -
arch/arm/mach-shmobile/r8a7740.h | 58 -
arch/arm/mach-shmobile/setup-r8a7740.c | 732 +----------
arch/arm/mach-shmobile/setup-sh73a0.c | 739 +----------
arch/arm/mach-shmobile/sh73a0.h | 83 --
arch/arm/mach-shmobile/smp-sh73a0.c | 8 -
drivers/pinctrl/sh-pfc/core.c | 6 -
drivers/pinctrl/sh-pfc/pfc-r8a7740.c | 4 -
drivers/pinctrl/sh-pfc/pfc-sh73a0.c | 4 -
30 files changed, 7 insertions(+), 6957 deletions(-)
delete mode 100644 arch/arm/boot/compressed/head-shmobile.S
delete mode 100644 arch/arm/configs/armadillo800eva_defconfig
delete mode 100644 arch/arm/configs/kzm9g_defconfig
delete mode 100644 arch/arm/mach-shmobile/board-armadillo800eva.c
delete mode 100644 arch/arm/mach-shmobile/board-kzm9g.c
delete mode 100644 arch/arm/mach-shmobile/clock-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/clock-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/dma-register.h
delete mode 100644 arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot.h
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot_macros.h
delete mode 100644 arch/arm/mach-shmobile/intc-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/pm-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/pm-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/r8a7740.h
--
1.9.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Hi Simon, Magnus,
The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
A1 (r8a7740) multi-platform kernels.
Lacking areas are:
- USB (it does't work in legacy, neither),
- HDMI on armadillo (it doesn't work in legacy, neither),
- Camera on armadillo (we don't care),
- LCDC:
- on armadillo, this is supported by the board staging code,
- on kzm9g, the LCDC is wired to the legacy INTC, which is not
planned to be supported with DT,
- DMAC/IPMMU (no DT bindings are planned).
Hence this patch series removes legacy board and SoC code for
sh73a0/kzm9g and r8a7740/armadillo.
It consists of 4 parts:
- Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
dtb) and sh73a0,
- Patches 5-8 remove legacy support for armadillo (board code,
defconfig, dtb) and r8a7740,
- Patches 9-11 remove generic shmobile support code (dma-register.h,
legacy PM Domains, zboot) that became unused by the removal of
legacy sh73a0/kzm9g and r8a7740/armadillo,
- Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
pinctrl drivers.
Dependencies:
- This is against next-20150617,
- To keep up with existing LCDC functionality for armadillo-legacy,
the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
0/7] staging: board: armadillo800eva: Board staging for
sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
However, it can be applied as-is now, and board staging can he
handled in parallel (if at all).
Thanks for applying!
Geert Uytterhoeven (15):
ARM: shmobile: Remove legacy board code for KZM-A9-GT
ARM: shmobile: Remove legacy kzm9g_defconfig
ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
ARM: shmobile: Remove legacy armadillo800eva_defconfig
ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
ARM: shmobile: Remove legacy SoC code for R-Mobile A1
ARM: shmobile: Remove unused dma-register.h
ARM: shmobile: R-Mobile: Remove legacy PM Domain code
ARM: shmobile: Remove obsolete zboot support
pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
MAINTAINERS | 2 -
arch/arm/boot/compressed/Makefile | 4 -
arch/arm/boot/compressed/head-shmobile.S | 71 -
arch/arm/boot/dts/Makefile | 4 +-
arch/arm/configs/armadillo800eva_defconfig | 162 ---
arch/arm/configs/kzm9g_defconfig | 154 ---
arch/arm/mach-shmobile/Kconfig | 33 -
arch/arm/mach-shmobile/Makefile | 8 +-
arch/arm/mach-shmobile/Makefile.boot | 2 -
arch/arm/mach-shmobile/board-armadillo800eva.c | 1365 --------------------
arch/arm/mach-shmobile/board-kzm9g.c | 916 -------------
arch/arm/mach-shmobile/clock-r8a7740.c | 675 ----------
arch/arm/mach-shmobile/clock-sh73a0.c | 752 -----------
arch/arm/mach-shmobile/dma-register.h | 84 --
arch/arm/mach-shmobile/include/mach/head-kzm9g.txt | 410 ------
arch/arm/mach-shmobile/include/mach/zboot.h | 19 -
arch/arm/mach-shmobile/include/mach/zboot_macros.h | 108 --
arch/arm/mach-shmobile/intc-sh73a0.c | 337 -----
arch/arm/mach-shmobile/pm-r8a7740.c | 129 --
arch/arm/mach-shmobile/pm-rmobile.c | 39 -
arch/arm/mach-shmobile/pm-rmobile.h | 24 -
arch/arm/mach-shmobile/pm-sh73a0.c | 32 -
arch/arm/mach-shmobile/r8a7740.h | 58 -
arch/arm/mach-shmobile/setup-r8a7740.c | 732 +----------
arch/arm/mach-shmobile/setup-sh73a0.c | 739 +----------
arch/arm/mach-shmobile/sh73a0.h | 83 --
arch/arm/mach-shmobile/smp-sh73a0.c | 8 -
drivers/pinctrl/sh-pfc/core.c | 6 -
drivers/pinctrl/sh-pfc/pfc-r8a7740.c | 4 -
drivers/pinctrl/sh-pfc/pfc-sh73a0.c | 4 -
30 files changed, 7 insertions(+), 6957 deletions(-)
delete mode 100644 arch/arm/boot/compressed/head-shmobile.S
delete mode 100644 arch/arm/configs/armadillo800eva_defconfig
delete mode 100644 arch/arm/configs/kzm9g_defconfig
delete mode 100644 arch/arm/mach-shmobile/board-armadillo800eva.c
delete mode 100644 arch/arm/mach-shmobile/board-kzm9g.c
delete mode 100644 arch/arm/mach-shmobile/clock-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/clock-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/dma-register.h
delete mode 100644 arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot.h
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot_macros.h
delete mode 100644 arch/arm/mach-shmobile/intc-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/pm-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/pm-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/r8a7740.h
--
1.9.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 01/15] ARM: shmobile: Remove legacy board code for KZM-A9-GT
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The KZM-A9-GT board is sufficiently supported by DT-based and board-less
SH-Mobile AG5 (sh73a0) multiplatform kernels. Hence remove the legacy
board code to reduce maintenance effort.
Lacking areas are:
- USB (it does't work in legacy, neither),
- LCDC (the LCDC is wired to the legacy INTC, which is not planned to
be supported with DT).
- DMAC/IPMMU (no DT bindings are planned).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 8 -
arch/arm/mach-shmobile/Makefile | 1 -
arch/arm/mach-shmobile/Makefile.boot | 1 -
arch/arm/mach-shmobile/board-kzm9g.c | 916 ---------------------
arch/arm/mach-shmobile/include/mach/head-kzm9g.txt | 410 ---------
arch/arm/mach-shmobile/include/mach/zboot.h | 5 -
arch/arm/mach-shmobile/intc-sh73a0.c | 337 --------
7 files changed, 1678 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/board-kzm9g.c
delete mode 100644 arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
delete mode 100644 arch/arm/mach-shmobile/intc-sh73a0.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 429157d437f518c4..2a4d8348b6299dff 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -176,14 +176,6 @@ config MACH_MARZEN
select REGULATOR_FIXED_VOLTAGE if REGULATOR
select USE_OF
-config MACH_KZM9G
- bool "KZM-A9-GT board"
- depends on ARCH_SH73A0
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select SND_SOC_AK4642 if SND_SIMPLE_CARD
- select USE_OF
-
comment "Renesas ARM SoCs System Configuration"
config CPU_HAS_INTEVT
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index def7a093d99cfaf9..9bdb8a11acb10c4e 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -60,7 +60,6 @@ obj-$(CONFIG_MACH_BOCKW) += board-bockw.o
obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
-obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o intc-sh73a0.o
endif
# Framework support
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index e1ef19cef89c7f34..2269b1c3c30b108a 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -3,7 +3,6 @@ loadaddr-y : loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000
loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
-loadaddr-$(CONFIG_MACH_KZM9G) += 0x41008000
loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
__ZRELADDR := $(sort $(loadaddr-y))
diff --git a/arch/arm/mach-shmobile/board-kzm9g.c b/arch/arm/mach-shmobile/board-kzm9g.c
deleted file mode 100644
index 260d8319fd82f927..0000000000000000
--- a/arch/arm/mach-shmobile/board-kzm9g.c
+++ /dev/null
@@ -1,916 +0,0 @@
-/*
- * KZM-A9-GT board support
- *
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/i2c.h>
-#include <linux/i2c/pcf857x.h>
-#include <linux/input.h>
-#include <linux/irqchip/arm-gic.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mmc/sh_mobile_sdhi.h>
-#include <linux/mfd/as3711.h>
-#include <linux/mfd/tmio.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/pinconf-generic.h>
-#include <linux/platform_device.h>
-#include <linux/reboot.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/smsc911x.h>
-#include <linux/usb/r8a66597.h>
-#include <linux/usb/renesas_usbhs.h>
-#include <linux/videodev2.h>
-
-#include <sound/sh_fsi.h>
-#include <sound/simple_card.h>
-#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <video/sh_mobile_lcdc.h>
-
-#include "common.h"
-#include "intc.h"
-#include "irqs.h"
-#include "sh73a0.h"
-
-/*
- * external GPIO
- */
-#define GPIO_PCF8575_BASE (310)
-#define GPIO_PCF8575_PORT10 (GPIO_PCF8575_BASE + 8)
-#define GPIO_PCF8575_PORT11 (GPIO_PCF8575_BASE + 9)
-#define GPIO_PCF8575_PORT12 (GPIO_PCF8575_BASE + 10)
-#define GPIO_PCF8575_PORT13 (GPIO_PCF8575_BASE + 11)
-#define GPIO_PCF8575_PORT14 (GPIO_PCF8575_BASE + 12)
-#define GPIO_PCF8575_PORT15 (GPIO_PCF8575_BASE + 13)
-#define GPIO_PCF8575_PORT16 (GPIO_PCF8575_BASE + 14)
-
-/* Dummy supplies, where voltage doesn't matter */
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-/*
- * FSI-AK4648
- *
- * this command is required when playback.
- *
- * # amixer set "LINEOUT Mixer DACL" on
- */
-
-/* SMSC 9221 */
-static struct resource smsc9221_resources[] = {
- [0] = {
- .start = 0x10000000, /* CS4 */
- .end = 0x100000ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = irq_pin(3), /* IRQ3 */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct smsc911x_platform_config smsc9221_platdata = {
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
-};
-
-static struct platform_device smsc_device = {
- .name = "smsc911x",
- .dev = {
- .platform_data = &smsc9221_platdata,
- },
- .resource = smsc9221_resources,
- .num_resources = ARRAY_SIZE(smsc9221_resources),
-};
-
-/* USB external chip */
-static struct r8a66597_platdata usb_host_data = {
- .on_chip = 0,
- .xtal = R8A66597_PLATDATA_XTAL_48MHZ,
-};
-
-static struct resource usb_resources[] = {
- [0] = {
- .start = 0x10010000,
- .end = 0x1001ffff - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = irq_pin(1), /* IRQ1 */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usb_host_device = {
- .name = "r8a66597_hcd",
- .dev = {
- .platform_data = &usb_host_data,
- .dma_mask = NULL,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(usb_resources),
- .resource = usb_resources,
-};
-
-/* USB Func CN17 */
-struct usbhs_private {
- void __iomem *phy;
- void __iomem *cr2;
- struct renesas_usbhs_platform_info info;
-};
-
-#define IRQ15 irq_pin(15)
-#define USB_PHY_MODE (1 << 4)
-#define USB_PHY_INT_EN ((1 << 3) | (1 << 2))
-#define USB_PHY_ON (1 << 1)
-#define USB_PHY_OFF (1 << 0)
-#define USB_PHY_INT_CLR (USB_PHY_ON | USB_PHY_OFF)
-
-#define usbhs_get_priv(pdev) \
- container_of(renesas_usbhs_get_info(pdev), struct usbhs_private, info)
-
-static int usbhs_get_vbus(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- return !((1 << 7) & __raw_readw(priv->cr2));
-}
-
-static int usbhs_phy_reset(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- /* init phy */
- __raw_writew(0x8a0a, priv->cr2);
-
- return 0;
-}
-
-static int usbhs_get_id(struct platform_device *pdev)
-{
- return USBHS_GADGET;
-}
-
-static irqreturn_t usbhs_interrupt(int irq, void *data)
-{
- struct platform_device *pdev = data;
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- renesas_usbhs_call_notify_hotplug(pdev);
-
- /* clear status */
- __raw_writew(__raw_readw(priv->phy) | USB_PHY_INT_CLR, priv->phy);
-
- return IRQ_HANDLED;
-}
-
-static int usbhs_hardware_init(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
- int ret;
-
- /* clear interrupt status */
- __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
-
- ret = request_irq(IRQ15, usbhs_interrupt, IRQF_TRIGGER_HIGH,
- dev_name(&pdev->dev), pdev);
- if (ret) {
- dev_err(&pdev->dev, "request_irq err\n");
- return ret;
- }
-
- /* enable USB phy interrupt */
- __raw_writew(USB_PHY_MODE | USB_PHY_INT_EN, priv->phy);
-
- return 0;
-}
-
-static int usbhs_hardware_exit(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- /* clear interrupt status */
- __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
-
- free_irq(IRQ15, pdev);
-
- return 0;
-}
-
-static u32 usbhs_pipe_cfg[] = {
- USB_ENDPOINT_XFER_CONTROL,
- USB_ENDPOINT_XFER_ISOC,
- USB_ENDPOINT_XFER_ISOC,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_INT,
- USB_ENDPOINT_XFER_INT,
- USB_ENDPOINT_XFER_INT,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
-};
-
-static struct usbhs_private usbhs_private = {
- .phy = IOMEM(0xe60781e0), /* USBPHYINT */
- .cr2 = IOMEM(0xe605810c), /* USBCR2 */
- .info = {
- .platform_callback = {
- .hardware_init = usbhs_hardware_init,
- .hardware_exit = usbhs_hardware_exit,
- .get_id = usbhs_get_id,
- .phy_reset = usbhs_phy_reset,
- .get_vbus = usbhs_get_vbus,
- },
- .driver_param = {
- .buswait_bwait = 4,
- .has_otg = 1,
- .pipe_type = usbhs_pipe_cfg,
- .pipe_size = ARRAY_SIZE(usbhs_pipe_cfg),
- },
- },
-};
-
-static struct resource usbhs_resources[] = {
- [0] = {
- .start = 0xE6890000,
- .end = 0xE68900e6 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(62),
- .end = gic_spi(62),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usbhs_device = {
- .name = "renesas_usbhs",
- .id = -1,
- .dev = {
- .dma_mask = NULL,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = &usbhs_private.info,
- },
- .num_resources = ARRAY_SIZE(usbhs_resources),
- .resource = usbhs_resources,
-};
-
-/* LCDC */
-static struct fb_videomode kzm_lcdc_mode = {
- .name = "WVGA Panel",
- .xres = 800,
- .yres = 480,
- .left_margin = 220,
- .right_margin = 110,
- .hsync_len = 70,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .sync = 0,
-};
-
-static struct sh_mobile_lcdc_info lcdc_info = {
- .clock_source = LCDC_CLK_BUS,
- .ch[0] = {
- .chan = LCDC_CHAN_MAINLCD,
- .fourcc = V4L2_PIX_FMT_RGB565,
- .interface_type = RGB24,
- .lcd_modes = &kzm_lcdc_mode,
- .num_modes = 1,
- .clock_divider = 5,
- .flags = 0,
- .panel_cfg = {
- .width = 152,
- .height = 91,
- },
- }
-};
-
-static struct resource lcdc_resources[] = {
- [0] = {
- .name = "LCDC",
- .start = 0xfe940000,
- .end = 0xfe943fff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = intcs_evt2irq(0x580),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device lcdc_device = {
- .name = "sh_mobile_lcdc_fb",
- .num_resources = ARRAY_SIZE(lcdc_resources),
- .resource = lcdc_resources,
- .dev = {
- .platform_data = &lcdc_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-/* Fixed 1.8V regulator to be used by MMCIF */
-static struct regulator_consumer_supply fixed1v8_power_consumers[] -{
- REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
- REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
-};
-
-/* MMCIF */
-static struct resource sh_mmcif_resources[] = {
- [0] = {
- .name = "MMCIF",
- .start = 0xe6bd0000,
- .end = 0xe6bd00ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(140),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = gic_spi(141),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct sh_mmcif_plat_data sh_mmcif_platdata = {
- .ocr = MMC_VDD_165_195,
- .caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
- .ccs_unsupported = true,
- .slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
- .slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
-};
-
-static struct platform_device mmc_device = {
- .name = "sh_mmcif",
- .dev = {
- .dma_mask = NULL,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = &sh_mmcif_platdata,
- },
- .num_resources = ARRAY_SIZE(sh_mmcif_resources),
- .resource = sh_mmcif_resources,
-};
-
-/* Fixed 3.3V regulators to be used by SDHI0 */
-static struct regulator_consumer_supply vcc_sdhi0_consumers[] -{
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vcc_sdhi0_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
- .consumer_supplies = vcc_sdhi0_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi0_info = {
- .supply_name = "SDHI0 Vcc",
- .microvolts = 3300000,
- .gpio = 15,
- .enable_high = 1,
- .init_data = &vcc_sdhi0_init_data,
-};
-
-static struct platform_device vcc_sdhi0 = {
- .name = "reg-fixed-voltage",
- .id = 0,
- .dev = {
- .platform_data = &vcc_sdhi0_info,
- },
-};
-
-/* Fixed 3.3V regulators to be used by SDHI2 */
-static struct regulator_consumer_supply vcc_sdhi2_consumers[] -{
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.2"),
-};
-
-static struct regulator_init_data vcc_sdhi2_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi2_consumers),
- .consumer_supplies = vcc_sdhi2_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi2_info = {
- .supply_name = "SDHI2 Vcc",
- .microvolts = 3300000,
- .gpio = 14,
- .enable_high = 1,
- .init_data = &vcc_sdhi2_init_data,
-};
-
-static struct platform_device vcc_sdhi2 = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &vcc_sdhi2_info,
- },
-};
-
-/* SDHI */
-static struct tmio_mmc_data sdhi0_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI0_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI0_RX,
- .flags = TMIO_MMC_HAS_IDLE_WAIT,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
- MMC_CAP_POWER_OFF_CARD,
-};
-
-static struct resource sdhi0_resources[] = {
- [0] = {
- .name = "SDHI0",
- .start = 0xee100000,
- .end = 0xee1000ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .name = SH_MOBILE_SDHI_IRQ_CARD_DETECT,
- .start = gic_spi(83),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .name = SH_MOBILE_SDHI_IRQ_SDCARD,
- .start = gic_spi(84),
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .name = SH_MOBILE_SDHI_IRQ_SDIO,
- .start = gic_spi(85),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi0_device = {
- .name = "sh_mobile_sdhi",
- .num_resources = ARRAY_SIZE(sdhi0_resources),
- .resource = sdhi0_resources,
- .dev = {
- .platform_data = &sdhi0_info,
- },
-};
-
-/* Micro SD */
-static struct tmio_mmc_data sdhi2_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI2_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI2_RX,
- .flags = TMIO_MMC_HAS_IDLE_WAIT |
- TMIO_MMC_USE_GPIO_CD |
- TMIO_MMC_WRPROTECT_DISABLE,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_POWER_OFF_CARD,
- .cd_gpio = 13,
-};
-
-static struct resource sdhi2_resources[] = {
- [0] = {
- .name = "SDHI2",
- .start = 0xee140000,
- .end = 0xee1400ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .name = SH_MOBILE_SDHI_IRQ_CARD_DETECT,
- .start = gic_spi(103),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .name = SH_MOBILE_SDHI_IRQ_SDCARD,
- .start = gic_spi(104),
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .name = SH_MOBILE_SDHI_IRQ_SDIO,
- .start = gic_spi(105),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi2_device = {
- .name = "sh_mobile_sdhi",
- .id = 2,
- .num_resources = ARRAY_SIZE(sdhi2_resources),
- .resource = sdhi2_resources,
- .dev = {
- .platform_data = &sdhi2_info,
- },
-};
-
-/* KEY */
-#define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
-
-static struct gpio_keys_button gpio_buttons[] = {
- GPIO_KEY(KEY_BACK, GPIO_PCF8575_PORT10, "SW3"),
- GPIO_KEY(KEY_RIGHT, GPIO_PCF8575_PORT11, "SW2-R"),
- GPIO_KEY(KEY_LEFT, GPIO_PCF8575_PORT12, "SW2-L"),
- GPIO_KEY(KEY_ENTER, GPIO_PCF8575_PORT13, "SW2-P"),
- GPIO_KEY(KEY_UP, GPIO_PCF8575_PORT14, "SW2-U"),
- GPIO_KEY(KEY_DOWN, GPIO_PCF8575_PORT15, "SW2-D"),
- GPIO_KEY(KEY_HOME, GPIO_PCF8575_PORT16, "SW1"),
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device gpio_keys_device = {
- .name = "gpio-keys",
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-/* FSI-AK4648 */
-static struct sh_fsi_platform_info fsi_info = {
- .port_a = {
- .tx_id = SHDMA_SLAVE_FSI2A_TX,
- },
-};
-
-static struct resource fsi_resources[] = {
- [0] = {
- .name = "FSI",
- .start = 0xEC230000,
- .end = 0xEC230400 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(146),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device fsi_device = {
- .name = "sh_fsi2",
- .id = -1,
- .num_resources = ARRAY_SIZE(fsi_resources),
- .resource = fsi_resources,
- .dev = {
- .platform_data = &fsi_info,
- },
-};
-
-static struct asoc_simple_card_info fsi2_ak4648_info = {
- .name = "AK4648",
- .card = "FSI2A-AK4648",
- .codec = "ak4642-codec.0-0012",
- .platform = "sh_fsi2",
- .daifmt = SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_CBM_CFM,
- .cpu_dai = {
- .name = "fsia-dai",
- },
- .codec_dai = {
- .name = "ak4642-hifi",
- .sysclk = 11289600,
- },
-};
-
-static struct platform_device fsi_ak4648_device = {
- .name = "asoc-simple-card",
- .dev = {
- .platform_data = &fsi2_ak4648_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .dma_mask = &fsi_ak4648_device.dev.coherent_dma_mask,
- },
-};
-
-/* I2C */
-
-/* StepDown1 is used to supply 1.315V to the CPU */
-static struct regulator_init_data as3711_sd1 = {
- .constraints = {
- .name = "1.315V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1315000,
- .max_uV = 1335000,
- },
-};
-
-/* StepDown2 is used to supply 1.8V to the CPU and to the board */
-static struct regulator_init_data as3711_sd2 = {
- .constraints = {
- .name = "1.8V",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1800000,
- .max_uV = 1800000,
- },
-};
-
-/*
- * StepDown3 is switched in parallel with StepDown2, seems to be off,
- * according to read-back pre-set register values
- */
-
-/* StepDown4 is used to supply 1.215V to the CPU and to the board */
-static struct regulator_init_data as3711_sd4 = {
- .constraints = {
- .name = "1.215V",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1215000,
- .max_uV = 1235000,
- },
-};
-
-/* LDO1 is unused and unconnected */
-
-/* LDO2 is used to supply 2.8V to the CPU */
-static struct regulator_init_data as3711_ldo2 = {
- .constraints = {
- .name = "2.8V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 2800000,
- .max_uV = 2800000,
- },
-};
-
-/* LDO3 is used to supply 3.0V to the CPU */
-static struct regulator_init_data as3711_ldo3 = {
- .constraints = {
- .name = "3.0V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 3000000,
- .max_uV = 3000000,
- },
-};
-
-/* LDO4 is used to supply 2.8V to the board */
-static struct regulator_init_data as3711_ldo4 = {
- .constraints = {
- .name = "2.8V",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 2800000,
- .max_uV = 2800000,
- },
-};
-
-/* LDO5 is switched parallel to LDO4, also set to 2.8V */
-static struct regulator_init_data as3711_ldo5 = {
- .constraints = {
- .name = "2.8V #2",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 2800000,
- .max_uV = 2800000,
- },
-};
-
-/* LDO6 is unused and unconnected */
-
-/* LDO7 is used to supply 1.15V to the CPU */
-static struct regulator_init_data as3711_ldo7 = {
- .constraints = {
- .name = "1.15V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1150000,
- .max_uV = 1150000,
- },
-};
-
-/* LDO8 is switched parallel to LDO7, also set to 1.15V */
-static struct regulator_init_data as3711_ldo8 = {
- .constraints = {
- .name = "1.15V CPU #2",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1150000,
- .max_uV = 1150000,
- },
-};
-
-static struct as3711_platform_data as3711_pdata = {
- .regulator = {
- .init_data = {
- [AS3711_REGULATOR_SD_1] = &as3711_sd1,
- [AS3711_REGULATOR_SD_2] = &as3711_sd2,
- [AS3711_REGULATOR_SD_4] = &as3711_sd4,
- [AS3711_REGULATOR_LDO_2] = &as3711_ldo2,
- [AS3711_REGULATOR_LDO_3] = &as3711_ldo3,
- [AS3711_REGULATOR_LDO_4] = &as3711_ldo4,
- [AS3711_REGULATOR_LDO_5] = &as3711_ldo5,
- [AS3711_REGULATOR_LDO_7] = &as3711_ldo7,
- [AS3711_REGULATOR_LDO_8] = &as3711_ldo8,
- },
- },
- .backlight = {
- .su2_fb = "sh_mobile_lcdc_fb.0",
- .su2_max_uA = 36000,
- .su2_feedback = AS3711_SU2_CURR_AUTO,
- .su2_fbprot = AS3711_SU2_GPIO4,
- .su2_auto_curr1 = true,
- .su2_auto_curr2 = true,
- .su2_auto_curr3 = true,
- },
-};
-
-static struct pcf857x_platform_data pcf8575_pdata = {
- .gpio_base = GPIO_PCF8575_BASE,
-};
-
-static struct i2c_board_info i2c0_devices[] = {
- {
- I2C_BOARD_INFO("ak4648", 0x12),
- },
- {
- I2C_BOARD_INFO("r2025sd", 0x32),
- },
- {
- I2C_BOARD_INFO("ak8975", 0x0c),
- .irq = irq_pin(28), /* IRQ28 */
- },
- {
- I2C_BOARD_INFO("adxl34x", 0x1d),
- .irq = irq_pin(26), /* IRQ26 */
- },
- {
- I2C_BOARD_INFO("as3711", 0x40),
- .irq = intcs_evt2irq(0x3300), /* IRQ24 */
- .platform_data = &as3711_pdata,
- },
-};
-
-static struct i2c_board_info i2c1_devices[] = {
- {
- I2C_BOARD_INFO("st1232-ts", 0x55),
- .irq = irq_pin(8), /* IRQ8 */
- },
-};
-
-static struct i2c_board_info i2c3_devices[] = {
- {
- I2C_BOARD_INFO("pcf8575", 0x20),
- .irq = irq_pin(19), /* IRQ19 */
- .platform_data = &pcf8575_pdata,
- },
-};
-
-static struct platform_device *kzm_devices[] __initdata = {
- &smsc_device,
- &usb_host_device,
- &usbhs_device,
- &lcdc_device,
- &mmc_device,
- &vcc_sdhi0,
- &vcc_sdhi2,
- &sdhi0_device,
- &sdhi2_device,
- &gpio_keys_device,
- &fsi_device,
- &fsi_ak4648_device,
-};
-
-static unsigned long pin_pullup_conf[] = {
- PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 0),
-};
-
-static const struct pinctrl_map kzm_pinctrl_map[] = {
- /* FSIA (AK4648) */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_mclk_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_sclk_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_data_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_data_out", "fsia"),
- /* I2C3 */
- PIN_MAP_MUX_GROUP_DEFAULT("i2c-sh_mobile.3", "pfc-sh73a0",
- "i2c3_1", "i2c3"),
- /* LCD */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh73a0",
- "lcd_data24", "lcd"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh73a0",
- "lcd_sync", "lcd"),
- /* MMCIF */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "mmc0_data8_0", "mmc0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "mmc0_ctrl_0", "mmc0"),
- PIN_MAP_CONFIGS_PIN_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "PORT279", pin_pullup_conf),
- PIN_MAP_CONFIGS_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "mmc0_data8_0", pin_pullup_conf),
- /* SCIFA4 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.4", "pfc-sh73a0",
- "scifa4_data", "scifa4"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.4", "pfc-sh73a0",
- "scifa4_ctrl", "scifa4"),
- /* SDHI0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_data4", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_ctrl", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_cd", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_wp", "sdhi0"),
- /* SDHI2 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.2", "pfc-sh73a0",
- "sdhi2_data4", "sdhi2"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.2", "pfc-sh73a0",
- "sdhi2_ctrl", "sdhi2"),
- /* SMSC */
- PIN_MAP_MUX_GROUP_DEFAULT("smsc911x.0", "pfc-sh73a0",
- "bsc_cs4", "bsc"),
- /* USB */
- PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-sh73a0",
- "usb_vbus", "usb"),
-};
-
-static void __init kzm_init(void)
-{
- regulator_register_always_on(2, "fixed-1.8V", fixed1v8_power_consumers,
- ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
- regulator_register_fixed(3, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- pinctrl_register_mappings(kzm_pinctrl_map, ARRAY_SIZE(kzm_pinctrl_map));
-
- sh73a0_pinmux_init();
-
- /* SMSC */
- gpio_request_one(224, GPIOF_IN, NULL); /* IRQ3 */
-
- /* LCDC */
- gpio_request_one(222, GPIOF_OUT_INIT_HIGH, NULL); /* LCDCDON */
- gpio_request_one(226, GPIOF_OUT_INIT_HIGH, NULL); /* SC */
-
- /* Touchscreen */
- gpio_request_one(223, GPIOF_IN, NULL); /* IRQ8 */
-
-#ifdef CONFIG_CACHE_L2X0
- /* Shared attribute override enable, 64K*8way */
- l2x0_init(IOMEM(0xf0100000), 0x00400000, 0xc20f0fff);
-#endif
-
- i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
- i2c_register_board_info(1, i2c1_devices, ARRAY_SIZE(i2c1_devices));
- i2c_register_board_info(3, i2c3_devices, ARRAY_SIZE(i2c3_devices));
-
- sh73a0_add_standard_devices();
- platform_add_devices(kzm_devices, ARRAY_SIZE(kzm_devices));
-
- sh73a0_pm_init();
-}
-
-static void kzm9g_restart(enum reboot_mode mode, const char *cmd)
-{
-#define RESCNT2 IOMEM(0xe6188020)
- /* Do soft power on reset */
- writel((1 << 31), RESCNT2);
-}
-
-static const char *kzm9g_boards_compat_dt[] __initdata = {
- "renesas,kzm9g",
- NULL,
-};
-
-DT_MACHINE_START(KZM9G_DT, "kzm9g")
- .smp = smp_ops(sh73a0_smp_ops),
- .map_io = sh73a0_map_io,
- .init_early = sh73a0_add_early_devices,
- .init_irq = sh73a0_init_irq,
- .init_machine = kzm_init,
- .init_late = shmobile_init_late,
- .init_time = sh73a0_earlytimer_init,
- .restart = kzm9g_restart,
- .dt_compat = kzm9g_boards_compat_dt,
-MACHINE_END
diff --git a/arch/arm/mach-shmobile/include/mach/head-kzm9g.txt b/arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
deleted file mode 100644
index 9531f46a822a1b22..0000000000000000
--- a/arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
+++ /dev/null
@@ -1,410 +0,0 @@
-LIST "KZM9G low-level initialization routine."
-LIST "Adapted from u-boot KZM9G support code."
-
-LIST "Copyright (C) 2013 Ulrich Hecht"
-
-LIST "This program is free software; you can redistribute it and/or modify"
-LIST "it under the terms of the GNU General Public License version 2 as"
-LIST "published by the Free Software Foundation."
-
-LIST "This program is distributed in the hope that it will be useful,"
-LIST "but WITHOUT ANY WARRANTY; without even the implied warranty of"
-LIST "MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the"
-LIST "GNU General Public License for more details."
-
-
-LIST "Register definitions:"
-
-LIST "Secure control register"
-#define LIFEC_SEC_SRC (0xE6110008)
-
-LIST "RWDT"
-#define RWDT_BASE (0xE6020000)
-#define RWTCSRA0 (RWDT_BASE + 0x04)
-
-LIST "HPB Semaphore Control Registers"
-#define HPBSCR_BASE (0xE6000000)
-#define HPBCTRL6 (HPBSCR_BASE + 0x1030)
-
-#define SBSC1_BASE (0xFE400000)
-#define SDCR0A (SBSC1_BASE + 0x0008)
-#define SDCR1A (SBSC1_BASE + 0x000C)
-#define SDPCRA (SBSC1_BASE + 0x0010)
-#define SDCR0SA (SBSC1_BASE + 0x0018)
-#define SDCR1SA (SBSC1_BASE + 0x001C)
-#define RTCSRA (SBSC1_BASE + 0x0020)
-#define RTCORA (SBSC1_BASE + 0x0028)
-#define RTCORHA (SBSC1_BASE + 0x002C)
-#define SDWCRC0A (SBSC1_BASE + 0x0040)
-#define SDWCRC1A (SBSC1_BASE + 0x0044)
-#define SDWCR00A (SBSC1_BASE + 0x0048)
-#define SDWCR01A (SBSC1_BASE + 0x004C)
-#define SDWCR10A (SBSC1_BASE + 0x0050)
-#define SDWCR11A (SBSC1_BASE + 0x0054)
-#define SDWCR2A (SBSC1_BASE + 0x0060)
-#define SDWCRC2A (SBSC1_BASE + 0x0064)
-#define ZQCCRA (SBSC1_BASE + 0x0068)
-#define SDMRACR0A (SBSC1_BASE + 0x0084)
-#define SDMRTMPCRA (SBSC1_BASE + 0x008C)
-#define SDMRTMPMSKA (SBSC1_BASE + 0x0094)
-#define SDGENCNTA (SBSC1_BASE + 0x009C)
-#define SDDRVCR0A (SBSC1_BASE + 0x00B4)
-#define DLLCNT0A (SBSC1_BASE + 0x0354)
-
-#define SDMRA1 (0xFE500000)
-#define SDMRA2 (0xFE5C0000)
-#define SDMRA3 (0xFE504000)
-
-#define SBSC2_BASE (0xFB400000)
-#define SDCR0B (SBSC2_BASE + 0x0008)
-#define SDCR1B (SBSC2_BASE + 0x000C)
-#define SDPCRB (SBSC2_BASE + 0x0010)
-#define SDCR0SB (SBSC2_BASE + 0x0018)
-#define SDCR1SB (SBSC2_BASE + 0x001C)
-#define RTCSRB (SBSC2_BASE + 0x0020)
-#define RTCORB (SBSC2_BASE + 0x0028)
-#define RTCORHB (SBSC2_BASE + 0x002C)
-#define SDWCRC0B (SBSC2_BASE + 0x0040)
-#define SDWCRC1B (SBSC2_BASE + 0x0044)
-#define SDWCR00B (SBSC2_BASE + 0x0048)
-#define SDWCR01B (SBSC2_BASE + 0x004C)
-#define SDWCR10B (SBSC2_BASE + 0x0050)
-#define SDWCR11B (SBSC2_BASE + 0x0054)
-#define SDPDCR0B (SBSC2_BASE + 0x0058)
-#define SDWCR2B (SBSC2_BASE + 0x0060)
-#define SDWCRC2B (SBSC2_BASE + 0x0064)
-#define ZQCCRB (SBSC2_BASE + 0x0068)
-#define SDMRACR0B (SBSC2_BASE + 0x0084)
-#define SDMRTMPCRB (SBSC2_BASE + 0x008C)
-#define SDMRTMPMSKB (SBSC2_BASE + 0x0094)
-#define SDGENCNTB (SBSC2_BASE + 0x009C)
-#define DPHYCNT0B (SBSC2_BASE + 0x00A0)
-#define DPHYCNT1B (SBSC2_BASE + 0x00A4)
-#define DPHYCNT2B (SBSC2_BASE + 0x00A8)
-#define SDDRVCR0B (SBSC2_BASE + 0x00B4)
-#define DLLCNT0B (SBSC2_BASE + 0x0354)
-
-#define SDMRB1 (0xFB500000)
-#define SDMRB2 (0xFB5C0000)
-#define SDMRB3 (0xFB504000)
-
-#define CPG_BASE (0xE6150000)
-#define FRQCRA (CPG_BASE + 0x0000)
-#define FRQCRB (CPG_BASE + 0x0004)
-#define FRQCRD (CPG_BASE + 0x00E4)
-#define VCLKCR1 (CPG_BASE + 0x0008)
-#define VCLKCR2 (CPG_BASE + 0x000C)
-#define VCLKCR3 (CPG_BASE + 0x001C)
-#define ZBCKCR (CPG_BASE + 0x0010)
-#define FLCKCR (CPG_BASE + 0x0014)
-#define SD0CKCR (CPG_BASE + 0x0074)
-#define SD1CKCR (CPG_BASE + 0x0078)
-#define SD2CKCR (CPG_BASE + 0x007C)
-#define FSIACKCR (CPG_BASE + 0x0018)
-#define SUBCKCR (CPG_BASE + 0x0080)
-#define SPUACKCR (CPG_BASE + 0x0084)
-#define SPUVCKCR (CPG_BASE + 0x0094)
-#define MSUCKCR (CPG_BASE + 0x0088)
-#define HSICKCR (CPG_BASE + 0x008C)
-#define FSIBCKCR (CPG_BASE + 0x0090)
-#define MFCK1CR (CPG_BASE + 0x0098)
-#define MFCK2CR (CPG_BASE + 0x009C)
-#define DSITCKCR (CPG_BASE + 0x0060)
-#define DSI0PCKCR (CPG_BASE + 0x0064)
-#define DSI1PCKCR (CPG_BASE + 0x0068)
-#define DSI0PHYCR (CPG_BASE + 0x006C)
-#define DVFSCR3 (CPG_BASE + 0x0174)
-#define DVFSCR4 (CPG_BASE + 0x0178)
-#define DVFSCR5 (CPG_BASE + 0x017C)
-#define MPMODE (CPG_BASE + 0x00CC)
-
-#define PLLECR (CPG_BASE + 0x00D0)
-#define PLL0CR (CPG_BASE + 0x00D8)
-#define PLL1CR (CPG_BASE + 0x0028)
-#define PLL2CR (CPG_BASE + 0x002C)
-#define PLL3CR (CPG_BASE + 0x00DC)
-#define PLL0STPCR (CPG_BASE + 0x00F0)
-#define PLL1STPCR (CPG_BASE + 0x00C8)
-#define PLL2STPCR (CPG_BASE + 0x00F8)
-#define PLL3STPCR (CPG_BASE + 0x00FC)
-#define RMSTPCR0 (CPG_BASE + 0x0110)
-#define RMSTPCR1 (CPG_BASE + 0x0114)
-#define RMSTPCR2 (CPG_BASE + 0x0118)
-#define RMSTPCR3 (CPG_BASE + 0x011C)
-#define RMSTPCR4 (CPG_BASE + 0x0120)
-#define RMSTPCR5 (CPG_BASE + 0x0124)
-#define SMSTPCR0 (CPG_BASE + 0x0130)
-#define SMSTPCR2 (CPG_BASE + 0x0138)
-#define SMSTPCR3 (CPG_BASE + 0x013C)
-#define CPGXXCR4 (CPG_BASE + 0x0150)
-#define SRCR0 (CPG_BASE + 0x80A0)
-#define SRCR2 (CPG_BASE + 0x80B0)
-#define SRCR3 (CPG_BASE + 0x80A8)
-#define VREFCR (CPG_BASE + 0x00EC)
-#define PCLKCR (CPG_BASE + 0x1020)
-
-#define PORT32CR (0xE6051020)
-#define PORT33CR (0xE6051021)
-#define PORT34CR (0xE6051022)
-#define PORT35CR (0xE6051023)
-
-LIST "DRAM initialization code:"
-
-EW RWTCSRA0, 0xA507
-
-ED_AND LIFEC_SEC_SRC, 0xFFFF7FFF
-
-ED_AND SMSTPCR3,0xFFFF7FFF
-ED_AND SRCR3, 0xFFFF7FFF
-ED_AND SMSTPCR2,0xFFFBFFFF
-ED_AND SRCR2, 0xFFFBFFFF
-ED PLLECR, 0x00000000
-
-WAIT_MASK PLLECR, 0x00000F00, 0x00000000
-WAIT_MASK FRQCRB, 0x80000000, 0x00000000
-
-ED PLL0CR, 0x2D000000
-ED PLL1CR, 0x17100000
-ED FRQCRB, 0x96235880
-WAIT_MASK FRQCRB, 0x80000000, 0x00000000
-
-ED FLCKCR, 0x0000000B
-ED_AND SMSTPCR0, 0xFFFFFFFD
-
-ED_AND SRCR0, 0xFFFFFFFD
-ED 0xE6001628, 0x514
-ED 0xE6001648, 0x514
-ED 0xE6001658, 0x514
-ED 0xE6001678, 0x514
-
-ED DVFSCR4, 0x00092000
-ED DVFSCR5, 0x000000DC
-ED PLLECR, 0x00000000
-WAIT_MASK PLLECR, 0x00000F00, 0x00000000
-
-ED FRQCRA, 0x0012453C
-ED FRQCRB, 0x80431350
-WAIT_MASK FRQCRB, 0x80000000, 0x00000000
-ED FRQCRD, 0x00000B0B
-WAIT_MASK FRQCRD, 0x80000000, 0x00000000
-
-ED PCLKCR, 0x00000003
-ED VCLKCR1, 0x0000012F
-ED VCLKCR2, 0x00000119
-ED VCLKCR3, 0x00000119
-ED ZBCKCR, 0x00000002
-ED FLCKCR, 0x00000005
-ED SD0CKCR, 0x00000080
-ED SD1CKCR, 0x00000080
-ED SD2CKCR, 0x00000080
-ED FSIACKCR, 0x0000003F
-ED FSIBCKCR, 0x0000003F
-ED SUBCKCR, 0x00000080
-ED SPUACKCR, 0x0000000B
-ED SPUVCKCR, 0x0000000B
-ED MSUCKCR, 0x0000013F
-ED HSICKCR, 0x00000080
-ED MFCK1CR, 0x0000003F
-ED MFCK2CR, 0x0000003F
-ED DSITCKCR, 0x00000107
-ED DSI0PCKCR, 0x00000313
-ED DSI1PCKCR, 0x0000130D
-ED DSI0PHYCR, 0x2A800E0E
-ED PLL0CR, 0x1E000000
-ED PLL0CR, 0x2D000000
-ED PLL1CR, 0x17100000
-ED PLL2CR, 0x27000080
-ED PLL3CR, 0x1D000000
-ED PLL0STPCR, 0x00080000
-ED PLL1STPCR, 0x000120C0
-ED PLL2STPCR, 0x00012000
-ED PLL3STPCR, 0x00000030
-ED PLLECR, 0x0000000B
-WAIT_MASK PLLECR, 0x00000B00, 0x00000B00
-
-ED DVFSCR3, 0x000120F0
-ED MPMODE, 0x00000020
-ED VREFCR, 0x0000028A
-ED RMSTPCR0, 0xE4628087
-ED RMSTPCR1, 0xFFFFFFFF
-ED RMSTPCR2, 0x53FFFFFF
-ED RMSTPCR3, 0xFFFFFFFF
-ED RMSTPCR4, 0x00800D3D
-ED RMSTPCR5, 0xFFFFF3FF
-ED SMSTPCR2, 0x00000000
-ED SRCR2, 0x00040000
-ED_AND PLLECR, 0xFFFFFFF7
-WAIT_MASK PLLECR, 0x00000800, 0x00000000
-
-LIST "set SBSC operational"
-ED HPBCTRL6, 0x00000001
-WAIT_MASK HPBCTRL6, 0x00000001, 0x00000001
-
-LIST "set SBSC operating frequency"
-ED FRQCRD, 0x00001414
-WAIT_MASK FRQCRD, 0x80000000, 0x00000000
-ED PLL3CR, 0x1D000000
-ED_OR PLLECR, 0x00000008
-WAIT_MASK PLLECR, 0x00000800, 0x00000800
-
-LIST "enable DLL oscillation in DDRPHY"
-ED_OR DLLCNT0A, 0x00000002
-
-LIST "wait >= 100 ns"
-ED SDGENCNTA, 0x00000005
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "target LPDDR2 device settings"
-ED SDCR0A, 0xACC90159
-ED SDCR1A, 0x00010059
-ED SDWCRC0A, 0x50874114
-ED SDWCRC1A, 0x33199B37
-ED SDWCRC2A, 0x008F2313
-ED SDWCR00A, 0x31020707
-ED SDWCR01A, 0x0017040A
-ED SDWCR10A, 0x31020707
-ED SDWCR11A, 0x0017040A
-
-ED SDDRVCR0A, 0x055557ff
-
-ED SDWCR2A, 0x30000000
-
-LIST "drive CKE high"
-ED_OR SDPCRA, 0x00000080
-WAIT_MASK SDPCRA, 0x00000080, 0x00000080
-
-LIST "wait >= 200 us"
-ED SDGENCNTA, 0x00002710
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "issue reset command to LPDDR2 device"
-ED SDMRACR0A, 0x0000003F
-ED SDMRA1, 0x00000000
-
-LIST "wait >= 10 (or 1) us (docs inconsistent)"
-ED SDGENCNTA, 0x000001F4
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "MRW ZS initialization calibration command"
-ED SDMRACR0A, 0x0000FF0A
-ED SDMRA3, 0x00000000
-
-LIST "wait >= 1 us"
-ED SDGENCNTA, 0x00000032
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "specify operating mode in LPDDR2"
-ED SDMRACR0A, 0x00002201
-ED SDMRA1, 0x00000000
-ED SDMRACR0A, 0x00000402
-ED SDMRA1, 0x00000000
-ED SDMRACR0A, 0x00000203
-ED SDMRA1, 0x00000000
-
-LIST "initialize DDR interface"
-ED SDMRA2, 0x00000000
-
-LIST "temperature sensor control"
-ED SDMRTMPCRA, 0x88800004
-ED SDMRTMPMSKA,0x00000004
-
-LIST "auto-refreshing control"
-ED RTCORA, 0xA55A0032
-ED RTCORHA, 0xA55A000C
-ED RTCSRA, 0xA55A2048
-
-ED_OR SDCR0A, 0x00000800
-ED_OR SDCR1A, 0x00000400
-
-LIST "auto ZQ calibration control"
-ED ZQCCRA, 0xFFF20000
-
-ED_OR DLLCNT0B, 0x00000002
-ED SDGENCNTB, 0x00000005
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-
-ED SDCR0B, 0xACC90159
-ED SDCR1B, 0x00010059
-ED SDWCRC0B, 0x50874114
-ED SDWCRC1B, 0x33199B37
-ED SDWCRC2B, 0x008F2313
-ED SDWCR00B, 0x31020707
-ED SDWCR01B, 0x0017040A
-ED SDWCR10B, 0x31020707
-ED SDWCR11B, 0x0017040A
-ED SDDRVCR0B, 0x055557ff
-ED SDWCR2B, 0x30000000
-ED_OR SDPCRB, 0x00000080
-WAIT_MASK SDPCRB, 0x00000080, 0x00000080
-
-ED SDGENCNTB, 0x00002710
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-ED SDMRACR0B, 0x0000003F
-
-LIST "upstream u-boot writes to SDMRA1A for both SBSC 1 and 2, which does"
-LIST "not seem to make a lot of sense..."
-ED SDMRB1, 0x00000000
-
-ED SDGENCNTB, 0x000001F4
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-
-ED SDMRACR0B, 0x0000FF0A
-ED SDMRB3, 0x00000000
-ED SDGENCNTB, 0x00000032
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-
-ED SDMRACR0B, 0x00002201
-ED SDMRB1, 0x00000000
-ED SDMRACR0B, 0x00000402
-ED SDMRB1, 0x00000000
-ED SDMRACR0B, 0x00000203
-ED SDMRB1, 0x00000000
-ED SDMRB2, 0x00000000
-ED SDMRTMPCRB, 0x88800004
-ED SDMRTMPMSKB, 0x00000004
-ED RTCORB, 0xA55A0032
-ED RTCORHB, 0xA55A000C
-ED RTCSRB, 0xA55A2048
-ED_OR SDCR0B, 0x00000800
-ED_OR SDCR1B, 0x00000400
-ED ZQCCRB, 0xFFF20000
-ED_OR SDPDCR0B, 0x00030000
-ED DPHYCNT1B, 0xA5390000
-ED DPHYCNT0B, 0x00001200
-ED DPHYCNT1B, 0x07CE0000
-ED DPHYCNT0B, 0x00001247
-WAIT_MASK DPHYCNT2B, 0xFFFFFFFF, 0x07CE0000
-
-ED_AND SDPDCR0B, 0xFFFCFFFF
-
-ED FRQCRD, 0x00000B0B
-WAIT_MASK FRQCRD, 0x80000000, 0x00000000
-
-ED CPGXXCR4, 0xfffffffc
-
-LIST "Setup SCIF4 / workaround"
-EB PORT32CR, 0x12
-EB PORT33CR, 0x22
-EB PORT34CR, 0x12
-EB PORT35CR, 0x22
-
-EW 0xE6C80000, 0
-EB 0xE6C80004, 0x19
-EW 0xE6C80008, 0x0030
-EW 0xE6C80018, 0
-EW 0xE6C80030, 0x0014
-
-LIST "Magic to avoid hangs and corruption on DRAM writes."
-
-LIST "It has been observed that the system would most often hang while"
-LIST "decompressing the kernel, and if it didn't it would always write"
-LIST "a corrupt image to DRAM."
-LIST "This problem does not occur in u-boot, and the reason is that"
-LIST "u-boot performs an additional cache invalidation after setting up"
-LIST "the DRAM controller. Such an invalidation should not be necessary at"
-LIST "this point, and attempts at removing parts of the routine to arrive"
-LIST "at the minimal snippet of code necessary to avoid the DRAM stability"
-LIST "problem yielded the following:"
-
-MRC p15, 0, r0, c1, c0, 0
-MCR p15, 0, r0, c1, c0, 0
diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h
index 175ee05465da19eb..80f599f4b5ab5733 100644
--- a/arch/arm/mach-shmobile/include/mach/zboot.h
+++ b/arch/arm/mach-shmobile/include/mach/zboot.h
@@ -9,11 +9,6 @@
*
**************************************************/
-#ifdef CONFIG_MACH_KZM9G
-#define MEMORY_START 0x43000000
-#include "mach/head-kzm9g.txt"
-#else
#error "unsupported board."
-#endif
#endif /* ZBOOT_H */
diff --git a/arch/arm/mach-shmobile/intc-sh73a0.c b/arch/arm/mach-shmobile/intc-sh73a0.c
deleted file mode 100644
index fd63ae6532fc9ab2..0000000000000000
--- a/arch/arm/mach-shmobile/intc-sh73a0.c
+++ /dev/null
@@ -1,337 +0,0 @@
-/*
- * sh73a0 processor support - INTC hardware block
- *
- * Copyright (C) 2010 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <linux/irqchip.h>
-#include <linux/irqchip/arm-gic.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "intc.h"
-#include "irqs.h"
-#include "sh73a0.h"
-
-enum {
- UNUSED = 0,
-
- /* interrupt sources INTCS */
- PINTCS_PINT1, PINTCS_PINT2,
- RTDMAC_0_DEI0, RTDMAC_0_DEI1, RTDMAC_0_DEI2, RTDMAC_0_DEI3,
- CEU, MFI, BBIF2, VPU, TSIF1, _3DG_SGX543, _2DDMAC_2DDM0,
- RTDMAC_1_DEI4, RTDMAC_1_DEI5, RTDMAC_1_DADERR,
- KEYSC_KEY, VINT, MSIOF,
- TMU0_TUNI00, TMU0_TUNI01, TMU0_TUNI02,
- CMT0, TSIF0, CMT2, LMB, MSUG, MSU_MSU, MSU_MSU2,
- CTI, RWDT0, ICB, PEP, ASA, JPU_JPEG, LCDC, LCRC,
- RTDMAC_2_DEI6, RTDMAC_2_DEI7, RTDMAC_2_DEI8, RTDMAC_2_DEI9,
- RTDMAC_3_DEI10, RTDMAC_3_DEI11,
- FRC, GCU, LCDC1, CSIRX,
- DSITX0_DSITX00, DSITX0_DSITX01,
- SPU2_SPU0, SPU2_SPU1, FSI,
- TMU1_TUNI10, TMU1_TUNI11, TMU1_TUNI12,
- TSIF2, CMT4, MFIS2, CPORTS2R, TSG, DMASCH1, SCUW,
- VIO60, VIO61, CEU21, CSI21, DSITX1_DSITX10, DSITX1_DSITX11,
- DISP, DSRV, EMUX2_EMUX20I, EMUX2_EMUX21I,
- MSTIF0_MST00I, MSTIF0_MST01I, MSTIF1_MST10I, MSTIF1_MST11I,
- SPUV,
-
- /* interrupt groups INTCS */
- RTDMAC_0, RTDMAC_1, RTDMAC_2, RTDMAC_3,
- DSITX0, SPU2, TMU1, MSU,
-};
-
-static struct intc_vect intcs_vectors[] = {
- INTCS_VECT(PINTCS_PINT1, 0x0600), INTCS_VECT(PINTCS_PINT2, 0x0620),
- INTCS_VECT(RTDMAC_0_DEI0, 0x0800), INTCS_VECT(RTDMAC_0_DEI1, 0x0820),
- INTCS_VECT(RTDMAC_0_DEI2, 0x0840), INTCS_VECT(RTDMAC_0_DEI3, 0x0860),
- INTCS_VECT(CEU, 0x0880), INTCS_VECT(MFI, 0x0900),
- INTCS_VECT(BBIF2, 0x0960), INTCS_VECT(VPU, 0x0980),
- INTCS_VECT(TSIF1, 0x09a0), INTCS_VECT(_3DG_SGX543, 0x09e0),
- INTCS_VECT(_2DDMAC_2DDM0, 0x0a00),
- INTCS_VECT(RTDMAC_1_DEI4, 0x0b80), INTCS_VECT(RTDMAC_1_DEI5, 0x0ba0),
- INTCS_VECT(RTDMAC_1_DADERR, 0x0bc0),
- INTCS_VECT(KEYSC_KEY, 0x0be0), INTCS_VECT(VINT, 0x0c80),
- INTCS_VECT(MSIOF, 0x0d20),
- INTCS_VECT(TMU0_TUNI00, 0x0e80), INTCS_VECT(TMU0_TUNI01, 0x0ea0),
- INTCS_VECT(TMU0_TUNI02, 0x0ec0),
- INTCS_VECT(CMT0, 0x0f00), INTCS_VECT(TSIF0, 0x0f20),
- INTCS_VECT(CMT2, 0x0f40), INTCS_VECT(LMB, 0x0f60),
- INTCS_VECT(MSUG, 0x0f80),
- INTCS_VECT(MSU_MSU, 0x0fa0), INTCS_VECT(MSU_MSU2, 0x0fc0),
- INTCS_VECT(CTI, 0x0400), INTCS_VECT(RWDT0, 0x0440),
- INTCS_VECT(ICB, 0x0480), INTCS_VECT(PEP, 0x04a0),
- INTCS_VECT(ASA, 0x04c0), INTCS_VECT(JPU_JPEG, 0x0560),
- INTCS_VECT(LCDC, 0x0580), INTCS_VECT(LCRC, 0x05a0),
- INTCS_VECT(RTDMAC_2_DEI6, 0x1300), INTCS_VECT(RTDMAC_2_DEI7, 0x1320),
- INTCS_VECT(RTDMAC_2_DEI8, 0x1340), INTCS_VECT(RTDMAC_2_DEI9, 0x1360),
- INTCS_VECT(RTDMAC_3_DEI10, 0x1380), INTCS_VECT(RTDMAC_3_DEI11, 0x13a0),
- INTCS_VECT(FRC, 0x1700), INTCS_VECT(GCU, 0x1760),
- INTCS_VECT(LCDC1, 0x1780), INTCS_VECT(CSIRX, 0x17a0),
- INTCS_VECT(DSITX0_DSITX00, 0x17c0), INTCS_VECT(DSITX0_DSITX01, 0x17e0),
- INTCS_VECT(SPU2_SPU0, 0x1800), INTCS_VECT(SPU2_SPU1, 0x1820),
- INTCS_VECT(FSI, 0x1840),
- INTCS_VECT(TMU1_TUNI10, 0x1900), INTCS_VECT(TMU1_TUNI11, 0x1920),
- INTCS_VECT(TMU1_TUNI12, 0x1940),
- INTCS_VECT(TSIF2, 0x1960), INTCS_VECT(CMT4, 0x1980),
- INTCS_VECT(MFIS2, 0x1a00), INTCS_VECT(CPORTS2R, 0x1a20),
- INTCS_VECT(TSG, 0x1ae0), INTCS_VECT(DMASCH1, 0x1b00),
- INTCS_VECT(SCUW, 0x1b40),
- INTCS_VECT(VIO60, 0x1b60), INTCS_VECT(VIO61, 0x1b80),
- INTCS_VECT(CEU21, 0x1ba0), INTCS_VECT(CSI21, 0x1be0),
- INTCS_VECT(DSITX1_DSITX10, 0x1c00), INTCS_VECT(DSITX1_DSITX11, 0x1c20),
- INTCS_VECT(DISP, 0x1c40), INTCS_VECT(DSRV, 0x1c60),
- INTCS_VECT(EMUX2_EMUX20I, 0x1c80), INTCS_VECT(EMUX2_EMUX21I, 0x1ca0),
- INTCS_VECT(MSTIF0_MST00I, 0x1cc0), INTCS_VECT(MSTIF0_MST01I, 0x1ce0),
- INTCS_VECT(MSTIF1_MST10I, 0x1d00), INTCS_VECT(MSTIF1_MST11I, 0x1d20),
- INTCS_VECT(SPUV, 0x2300),
-};
-
-static struct intc_group intcs_groups[] __initdata = {
- INTC_GROUP(RTDMAC_0, RTDMAC_0_DEI0, RTDMAC_0_DEI1,
- RTDMAC_0_DEI2, RTDMAC_0_DEI3),
- INTC_GROUP(RTDMAC_1, RTDMAC_1_DEI4, RTDMAC_1_DEI5, RTDMAC_1_DADERR),
- INTC_GROUP(RTDMAC_2, RTDMAC_2_DEI6, RTDMAC_2_DEI7,
- RTDMAC_2_DEI8, RTDMAC_2_DEI9),
- INTC_GROUP(RTDMAC_3, RTDMAC_3_DEI10, RTDMAC_3_DEI11),
- INTC_GROUP(TMU1, TMU1_TUNI12, TMU1_TUNI11, TMU1_TUNI10),
- INTC_GROUP(DSITX0, DSITX0_DSITX00, DSITX0_DSITX01),
- INTC_GROUP(SPU2, SPU2_SPU0, SPU2_SPU1),
- INTC_GROUP(MSU, MSU_MSU, MSU_MSU2),
-};
-
-static struct intc_mask_reg intcs_mask_registers[] = {
- { 0xffd20184, 0xffd201c4, 8, /* IMR1SA / IMCR1SA */
- { 0, 0, 0, CEU,
- 0, 0, 0, 0 } },
- { 0xffd20188, 0xffd201c8, 8, /* IMR2SA / IMCR2SA */
- { 0, 0, 0, VPU,
- BBIF2, 0, 0, MFI } },
- { 0xffd2018c, 0xffd201cc, 8, /* IMR3SA / IMCR3SA */
- { 0, 0, 0, _2DDMAC_2DDM0,
- 0, ASA, PEP, ICB } },
- { 0xffd20190, 0xffd201d0, 8, /* IMR4SA / IMCR4SA */
- { 0, 0, 0, CTI,
- JPU_JPEG, 0, LCRC, LCDC } },
- { 0xffd20194, 0xffd201d4, 8, /* IMR5SA / IMCR5SA */
- { KEYSC_KEY, RTDMAC_1_DADERR, RTDMAC_1_DEI5, RTDMAC_1_DEI4,
- RTDMAC_0_DEI3, RTDMAC_0_DEI2, RTDMAC_0_DEI1, RTDMAC_0_DEI0 } },
- { 0xffd20198, 0xffd201d8, 8, /* IMR6SA / IMCR6SA */
- { 0, 0, MSIOF, 0,
- _3DG_SGX543, 0, 0, 0 } },
- { 0xffd2019c, 0xffd201dc, 8, /* IMR7SA / IMCR7SA */
- { 0, TMU0_TUNI02, TMU0_TUNI01, TMU0_TUNI00,
- 0, 0, 0, 0 } },
- { 0xffd201a0, 0xffd201e0, 8, /* IMR8SA / IMCR8SA */
- { 0, 0, 0, 0,
- 0, MSU_MSU, MSU_MSU2, MSUG } },
- { 0xffd201a4, 0xffd201e4, 8, /* IMR9SA / IMCR9SA */
- { 0, RWDT0, CMT2, CMT0,
- 0, 0, 0, 0 } },
- { 0xffd201ac, 0xffd201ec, 8, /* IMR11SA / IMCR11SA */
- { 0, 0, 0, 0,
- 0, TSIF1, LMB, TSIF0 } },
- { 0xffd201b0, 0xffd201f0, 8, /* IMR12SA / IMCR12SA */
- { 0, 0, 0, 0,
- 0, 0, PINTCS_PINT2, PINTCS_PINT1 } },
- { 0xffd50180, 0xffd501c0, 8, /* IMR0SA3 / IMCR0SA3 */
- { RTDMAC_2_DEI6, RTDMAC_2_DEI7, RTDMAC_2_DEI8, RTDMAC_2_DEI9,
- RTDMAC_3_DEI10, RTDMAC_3_DEI11, 0, 0 } },
- { 0xffd50190, 0xffd501d0, 8, /* IMR4SA3 / IMCR4SA3 */
- { FRC, 0, 0, GCU,
- LCDC1, CSIRX, DSITX0_DSITX00, DSITX0_DSITX01 } },
- { 0xffd50194, 0xffd501d4, 8, /* IMR5SA3 / IMCR5SA3 */
- { SPU2_SPU0, SPU2_SPU1, FSI, 0,
- 0, 0, 0, 0 } },
- { 0xffd50198, 0xffd501d8, 8, /* IMR6SA3 / IMCR6SA3 */
- { TMU1_TUNI10, TMU1_TUNI11, TMU1_TUNI12, 0,
- TSIF2, CMT4, 0, 0 } },
- { 0xffd5019c, 0xffd501dc, 8, /* IMR7SA3 / IMCR7SA3 */
- { MFIS2, CPORTS2R, 0, 0,
- 0, 0, 0, TSG } },
- { 0xffd501a0, 0xffd501e0, 8, /* IMR8SA3 / IMCR8SA3 */
- { DMASCH1, 0, SCUW, VIO60,
- VIO61, CEU21, 0, CSI21 } },
- { 0xffd501a4, 0xffd501e4, 8, /* IMR9SA3 / IMCR9SA3 */
- { DSITX1_DSITX10, DSITX1_DSITX11, DISP, DSRV,
- EMUX2_EMUX20I, EMUX2_EMUX21I, MSTIF0_MST00I, MSTIF0_MST01I } },
- { 0xffd501a8, 0xffd501e8, 8, /* IMR10SA3 / IMCR10SA3 */
- { MSTIF0_MST00I, MSTIF0_MST01I, 0, 0,
- 0, 0, 0, 0 } },
- { 0xffd60180, 0xffd601c0, 8, /* IMR0SA4 / IMCR0SA4 */
- { SPUV, 0, 0, 0,
- 0, 0, 0, 0 } },
-};
-
-/* Priority is needed for INTCA to receive the INTCS interrupt */
-static struct intc_prio_reg intcs_prio_registers[] = {
- { 0xffd20000, 0, 16, 4, /* IPRAS */ { CTI, 0, _2DDMAC_2DDM0, ICB } },
- { 0xffd20004, 0, 16, 4, /* IPRBS */ { JPU_JPEG, LCDC, 0, LCRC } },
- { 0xffd20008, 0, 16, 4, /* IPRCS */ { BBIF2, 0, 0, 0 } },
- { 0xffd2000c, 0, 16, 4, /* IPRDS */ { PINTCS_PINT1, PINTCS_PINT2,
- 0, 0 } },
- { 0xffd20010, 0, 16, 4, /* IPRES */ { RTDMAC_0, CEU, MFI, VPU } },
- { 0xffd20014, 0, 16, 4, /* IPRFS */ { KEYSC_KEY, RTDMAC_1,
- CMT2, CMT0 } },
- { 0xffd20018, 0, 16, 4, /* IPRGS */ { TMU0_TUNI00, TMU0_TUNI01,
- TMU0_TUNI02, TSIF1 } },
- { 0xffd2001c, 0, 16, 4, /* IPRHS */ { VINT, 0, 0, 0 } },
- { 0xffd20020, 0, 16, 4, /* IPRIS */ { 0, MSIOF, TSIF0, 0 } },
- { 0xffd20024, 0, 16, 4, /* IPRJS */ { 0, _3DG_SGX543, MSUG, MSU } },
- { 0xffd20028, 0, 16, 4, /* IPRKS */ { 0, ASA, LMB, PEP } },
- { 0xffd20030, 0, 16, 4, /* IPRMS */ { 0, 0, 0, RWDT0 } },
- { 0xffd50000, 0, 16, 4, /* IPRAS3 */ { RTDMAC_2, 0, 0, 0 } },
- { 0xffd50004, 0, 16, 4, /* IPRBS3 */ { RTDMAC_3, 0, 0, 0 } },
- { 0xffd50020, 0, 16, 4, /* IPRIS3 */ { FRC, 0, 0, 0 } },
- { 0xffd50024, 0, 16, 4, /* IPRJS3 */ { LCDC1, CSIRX, DSITX0, 0 } },
- { 0xffd50028, 0, 16, 4, /* IPRKS3 */ { SPU2, 0, FSI, 0 } },
- { 0xffd50030, 0, 16, 4, /* IPRMS3 */ { TMU1, 0, 0, TSIF2 } },
- { 0xffd50034, 0, 16, 4, /* IPRNS3 */ { CMT4, 0, 0, 0 } },
- { 0xffd50038, 0, 16, 4, /* IPROS3 */ { MFIS2, CPORTS2R, 0, 0 } },
- { 0xffd50040, 0, 16, 4, /* IPRQS3 */ { DMASCH1, 0, SCUW, VIO60 } },
- { 0xffd50044, 0, 16, 4, /* IPRRS3 */ { VIO61, CEU21, 0, CSI21 } },
- { 0xffd50048, 0, 16, 4, /* IPRSS3 */ { DSITX1_DSITX10, DSITX1_DSITX11,
- DISP, DSRV } },
- { 0xffd5004c, 0, 16, 4, /* IPRTS3 */ { EMUX2_EMUX20I, EMUX2_EMUX21I,
- MSTIF0_MST00I, MSTIF0_MST01I } },
- { 0xffd50050, 0, 16, 4, /* IPRUS3 */ { MSTIF1_MST10I, MSTIF1_MST11I,
- 0, 0 } },
- { 0xffd60000, 0, 16, 4, /* IPRAS4 */ { SPUV, 0, 0, 0 } },
-};
-
-static struct resource intcs_resources[] __initdata = {
- [0] = {
- .start = 0xffd20000,
- .end = 0xffd201ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = 0xffd50000,
- .end = 0xffd501ff,
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .start = 0xffd60000,
- .end = 0xffd601ff,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct intc_desc intcs_desc __initdata = {
- .name = "sh73a0-intcs",
- .resource = intcs_resources,
- .num_resources = ARRAY_SIZE(intcs_resources),
- .hw = INTC_HW_DESC(intcs_vectors, intcs_groups, intcs_mask_registers,
- intcs_prio_registers, NULL, NULL),
-};
-
-static struct irqaction sh73a0_intcs_cascade;
-
-static irqreturn_t sh73a0_intcs_demux(int irq, void *dev_id)
-{
- unsigned int evtcodeas = ioread32((void __iomem *)dev_id);
-
- generic_handle_irq(intcs_evt2irq(evtcodeas));
-
- return IRQ_HANDLED;
-}
-
-#define PINTER0_PHYS 0xe69000a0
-#define PINTER1_PHYS 0xe69000a4
-#define PINTER0_VIRT IOMEM(0xe69000a0)
-#define PINTER1_VIRT IOMEM(0xe69000a4)
-#define PINTRR0 IOMEM(0xe69000d0)
-#define PINTRR1 IOMEM(0xe69000d4)
-
-#define PINT0A_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq))
-#define PINT0B_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq + 8))
-#define PINT0C_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq + 16))
-#define PINT0D_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq + 24))
-#define PINT1E_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT1_IRQ(irq))
-
-INTC_PINT(intc_pint0, PINTER0_PHYS, 0xe69000b0, "sh73a0-pint0", \
- INTC_PINT_E(A), INTC_PINT_E(B), INTC_PINT_E(C), INTC_PINT_E(D), \
- INTC_PINT_V(A, PINT0A_IRQ), INTC_PINT_V(B, PINT0B_IRQ), \
- INTC_PINT_V(C, PINT0C_IRQ), INTC_PINT_V(D, PINT0D_IRQ), \
- INTC_PINT_E(A), INTC_PINT_E(B), INTC_PINT_E(C), INTC_PINT_E(D), \
- INTC_PINT_E(A), INTC_PINT_E(B), INTC_PINT_E(C), INTC_PINT_E(D));
-
-INTC_PINT(intc_pint1, PINTER1_PHYS, 0xe69000c0, "sh73a0-pint1", \
- INTC_PINT_E(E), INTC_PINT_E_EMPTY, INTC_PINT_E_EMPTY, INTC_PINT_E_EMPTY, \
- INTC_PINT_V(E, PINT1E_IRQ), INTC_PINT_V_NONE, \
- INTC_PINT_V_NONE, INTC_PINT_V_NONE, \
- INTC_PINT_E_NONE, INTC_PINT_E_NONE, INTC_PINT_E_NONE, INTC_PINT_E(E), \
- INTC_PINT_E(E), INTC_PINT_E_NONE, INTC_PINT_E_NONE, INTC_PINT_E_NONE);
-
-static struct irqaction sh73a0_pint0_cascade;
-static struct irqaction sh73a0_pint1_cascade;
-
-static void pint_demux(void __iomem *rr, void __iomem *er, int base_irq)
-{
- unsigned long value = ioread32(rr) & ioread32(er);
- int k;
-
- for (k = 0; k < 32; k++) {
- if (value & (1 << (31 - k))) {
- generic_handle_irq(base_irq + k);
- iowrite32(~(1 << (31 - k)), rr);
- }
- }
-}
-
-static irqreturn_t sh73a0_pint0_demux(int irq, void *dev_id)
-{
- pint_demux(PINTRR0, PINTER0_VIRT, SH73A0_PINT0_IRQ(0));
- return IRQ_HANDLED;
-}
-
-static irqreturn_t sh73a0_pint1_demux(int irq, void *dev_id)
-{
- pint_demux(PINTRR1, PINTER1_VIRT, SH73A0_PINT1_IRQ(0));
- return IRQ_HANDLED;
-}
-
-void __init sh73a0_init_irq(void)
-{
- void __iomem *gic_dist_base = IOMEM(0xf0001000);
- void __iomem *gic_cpu_base = IOMEM(0xf0000100);
- void __iomem *intevtsa = ioremap_nocache(0xffd20100, PAGE_SIZE);
-
- gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE);
- gic_init(0, 29, gic_dist_base, gic_cpu_base);
-
- register_intc_controller(&intcs_desc);
- register_intc_controller(&intc_pint0_desc);
- register_intc_controller(&intc_pint1_desc);
-
- /* demux using INTEVTSA */
- sh73a0_intcs_cascade.name = "INTCS cascade";
- sh73a0_intcs_cascade.handler = sh73a0_intcs_demux;
- sh73a0_intcs_cascade.dev_id = intevtsa;
- setup_irq(gic_spi(50), &sh73a0_intcs_cascade);
-
- /* PINT pins are sanely tied to the GIC as SPI */
- sh73a0_pint0_cascade.name = "PINT0 cascade";
- sh73a0_pint0_cascade.handler = sh73a0_pint0_demux;
- setup_irq(gic_spi(33), &sh73a0_pint0_cascade);
-
- sh73a0_pint1_cascade.name = "PINT1 cascade";
- sh73a0_pint1_cascade.handler = sh73a0_pint1_demux;
- setup_irq(gic_spi(34), &sh73a0_pint1_cascade);
-}
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 01/15] ARM: shmobile: Remove legacy board code for KZM-A9-GT
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The KZM-A9-GT board is sufficiently supported by DT-based and board-less
SH-Mobile AG5 (sh73a0) multiplatform kernels. Hence remove the legacy
board code to reduce maintenance effort.
Lacking areas are:
- USB (it does't work in legacy, neither),
- LCDC (the LCDC is wired to the legacy INTC, which is not planned to
be supported with DT).
- DMAC/IPMMU (no DT bindings are planned).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 8 -
arch/arm/mach-shmobile/Makefile | 1 -
arch/arm/mach-shmobile/Makefile.boot | 1 -
arch/arm/mach-shmobile/board-kzm9g.c | 916 ---------------------
arch/arm/mach-shmobile/include/mach/head-kzm9g.txt | 410 ---------
arch/arm/mach-shmobile/include/mach/zboot.h | 5 -
arch/arm/mach-shmobile/intc-sh73a0.c | 337 --------
7 files changed, 1678 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/board-kzm9g.c
delete mode 100644 arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
delete mode 100644 arch/arm/mach-shmobile/intc-sh73a0.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 429157d437f518c4..2a4d8348b6299dff 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -176,14 +176,6 @@ config MACH_MARZEN
select REGULATOR_FIXED_VOLTAGE if REGULATOR
select USE_OF
-config MACH_KZM9G
- bool "KZM-A9-GT board"
- depends on ARCH_SH73A0
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select SND_SOC_AK4642 if SND_SIMPLE_CARD
- select USE_OF
-
comment "Renesas ARM SoCs System Configuration"
config CPU_HAS_INTEVT
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index def7a093d99cfaf9..9bdb8a11acb10c4e 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -60,7 +60,6 @@ obj-$(CONFIG_MACH_BOCKW) += board-bockw.o
obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
-obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o intc-sh73a0.o
endif
# Framework support
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index e1ef19cef89c7f34..2269b1c3c30b108a 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -3,7 +3,6 @@ loadaddr-y :=
loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000
loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
-loadaddr-$(CONFIG_MACH_KZM9G) += 0x41008000
loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
__ZRELADDR := $(sort $(loadaddr-y))
diff --git a/arch/arm/mach-shmobile/board-kzm9g.c b/arch/arm/mach-shmobile/board-kzm9g.c
deleted file mode 100644
index 260d8319fd82f927..0000000000000000
--- a/arch/arm/mach-shmobile/board-kzm9g.c
+++ /dev/null
@@ -1,916 +0,0 @@
-/*
- * KZM-A9-GT board support
- *
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/i2c.h>
-#include <linux/i2c/pcf857x.h>
-#include <linux/input.h>
-#include <linux/irqchip/arm-gic.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mmc/sh_mobile_sdhi.h>
-#include <linux/mfd/as3711.h>
-#include <linux/mfd/tmio.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/pinconf-generic.h>
-#include <linux/platform_device.h>
-#include <linux/reboot.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/smsc911x.h>
-#include <linux/usb/r8a66597.h>
-#include <linux/usb/renesas_usbhs.h>
-#include <linux/videodev2.h>
-
-#include <sound/sh_fsi.h>
-#include <sound/simple_card.h>
-#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <video/sh_mobile_lcdc.h>
-
-#include "common.h"
-#include "intc.h"
-#include "irqs.h"
-#include "sh73a0.h"
-
-/*
- * external GPIO
- */
-#define GPIO_PCF8575_BASE (310)
-#define GPIO_PCF8575_PORT10 (GPIO_PCF8575_BASE + 8)
-#define GPIO_PCF8575_PORT11 (GPIO_PCF8575_BASE + 9)
-#define GPIO_PCF8575_PORT12 (GPIO_PCF8575_BASE + 10)
-#define GPIO_PCF8575_PORT13 (GPIO_PCF8575_BASE + 11)
-#define GPIO_PCF8575_PORT14 (GPIO_PCF8575_BASE + 12)
-#define GPIO_PCF8575_PORT15 (GPIO_PCF8575_BASE + 13)
-#define GPIO_PCF8575_PORT16 (GPIO_PCF8575_BASE + 14)
-
-/* Dummy supplies, where voltage doesn't matter */
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-/*
- * FSI-AK4648
- *
- * this command is required when playback.
- *
- * # amixer set "LINEOUT Mixer DACL" on
- */
-
-/* SMSC 9221 */
-static struct resource smsc9221_resources[] = {
- [0] = {
- .start = 0x10000000, /* CS4 */
- .end = 0x100000ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = irq_pin(3), /* IRQ3 */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct smsc911x_platform_config smsc9221_platdata = {
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
-};
-
-static struct platform_device smsc_device = {
- .name = "smsc911x",
- .dev = {
- .platform_data = &smsc9221_platdata,
- },
- .resource = smsc9221_resources,
- .num_resources = ARRAY_SIZE(smsc9221_resources),
-};
-
-/* USB external chip */
-static struct r8a66597_platdata usb_host_data = {
- .on_chip = 0,
- .xtal = R8A66597_PLATDATA_XTAL_48MHZ,
-};
-
-static struct resource usb_resources[] = {
- [0] = {
- .start = 0x10010000,
- .end = 0x1001ffff - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = irq_pin(1), /* IRQ1 */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usb_host_device = {
- .name = "r8a66597_hcd",
- .dev = {
- .platform_data = &usb_host_data,
- .dma_mask = NULL,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(usb_resources),
- .resource = usb_resources,
-};
-
-/* USB Func CN17 */
-struct usbhs_private {
- void __iomem *phy;
- void __iomem *cr2;
- struct renesas_usbhs_platform_info info;
-};
-
-#define IRQ15 irq_pin(15)
-#define USB_PHY_MODE (1 << 4)
-#define USB_PHY_INT_EN ((1 << 3) | (1 << 2))
-#define USB_PHY_ON (1 << 1)
-#define USB_PHY_OFF (1 << 0)
-#define USB_PHY_INT_CLR (USB_PHY_ON | USB_PHY_OFF)
-
-#define usbhs_get_priv(pdev) \
- container_of(renesas_usbhs_get_info(pdev), struct usbhs_private, info)
-
-static int usbhs_get_vbus(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- return !((1 << 7) & __raw_readw(priv->cr2));
-}
-
-static int usbhs_phy_reset(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- /* init phy */
- __raw_writew(0x8a0a, priv->cr2);
-
- return 0;
-}
-
-static int usbhs_get_id(struct platform_device *pdev)
-{
- return USBHS_GADGET;
-}
-
-static irqreturn_t usbhs_interrupt(int irq, void *data)
-{
- struct platform_device *pdev = data;
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- renesas_usbhs_call_notify_hotplug(pdev);
-
- /* clear status */
- __raw_writew(__raw_readw(priv->phy) | USB_PHY_INT_CLR, priv->phy);
-
- return IRQ_HANDLED;
-}
-
-static int usbhs_hardware_init(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
- int ret;
-
- /* clear interrupt status */
- __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
-
- ret = request_irq(IRQ15, usbhs_interrupt, IRQF_TRIGGER_HIGH,
- dev_name(&pdev->dev), pdev);
- if (ret) {
- dev_err(&pdev->dev, "request_irq err\n");
- return ret;
- }
-
- /* enable USB phy interrupt */
- __raw_writew(USB_PHY_MODE | USB_PHY_INT_EN, priv->phy);
-
- return 0;
-}
-
-static int usbhs_hardware_exit(struct platform_device *pdev)
-{
- struct usbhs_private *priv = usbhs_get_priv(pdev);
-
- /* clear interrupt status */
- __raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
-
- free_irq(IRQ15, pdev);
-
- return 0;
-}
-
-static u32 usbhs_pipe_cfg[] = {
- USB_ENDPOINT_XFER_CONTROL,
- USB_ENDPOINT_XFER_ISOC,
- USB_ENDPOINT_XFER_ISOC,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_INT,
- USB_ENDPOINT_XFER_INT,
- USB_ENDPOINT_XFER_INT,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
- USB_ENDPOINT_XFER_BULK,
-};
-
-static struct usbhs_private usbhs_private = {
- .phy = IOMEM(0xe60781e0), /* USBPHYINT */
- .cr2 = IOMEM(0xe605810c), /* USBCR2 */
- .info = {
- .platform_callback = {
- .hardware_init = usbhs_hardware_init,
- .hardware_exit = usbhs_hardware_exit,
- .get_id = usbhs_get_id,
- .phy_reset = usbhs_phy_reset,
- .get_vbus = usbhs_get_vbus,
- },
- .driver_param = {
- .buswait_bwait = 4,
- .has_otg = 1,
- .pipe_type = usbhs_pipe_cfg,
- .pipe_size = ARRAY_SIZE(usbhs_pipe_cfg),
- },
- },
-};
-
-static struct resource usbhs_resources[] = {
- [0] = {
- .start = 0xE6890000,
- .end = 0xE68900e6 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(62),
- .end = gic_spi(62),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usbhs_device = {
- .name = "renesas_usbhs",
- .id = -1,
- .dev = {
- .dma_mask = NULL,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = &usbhs_private.info,
- },
- .num_resources = ARRAY_SIZE(usbhs_resources),
- .resource = usbhs_resources,
-};
-
-/* LCDC */
-static struct fb_videomode kzm_lcdc_mode = {
- .name = "WVGA Panel",
- .xres = 800,
- .yres = 480,
- .left_margin = 220,
- .right_margin = 110,
- .hsync_len = 70,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .sync = 0,
-};
-
-static struct sh_mobile_lcdc_info lcdc_info = {
- .clock_source = LCDC_CLK_BUS,
- .ch[0] = {
- .chan = LCDC_CHAN_MAINLCD,
- .fourcc = V4L2_PIX_FMT_RGB565,
- .interface_type = RGB24,
- .lcd_modes = &kzm_lcdc_mode,
- .num_modes = 1,
- .clock_divider = 5,
- .flags = 0,
- .panel_cfg = {
- .width = 152,
- .height = 91,
- },
- }
-};
-
-static struct resource lcdc_resources[] = {
- [0] = {
- .name = "LCDC",
- .start = 0xfe940000,
- .end = 0xfe943fff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = intcs_evt2irq(0x580),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device lcdc_device = {
- .name = "sh_mobile_lcdc_fb",
- .num_resources = ARRAY_SIZE(lcdc_resources),
- .resource = lcdc_resources,
- .dev = {
- .platform_data = &lcdc_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-/* Fixed 1.8V regulator to be used by MMCIF */
-static struct regulator_consumer_supply fixed1v8_power_consumers[] =
-{
- REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
- REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
-};
-
-/* MMCIF */
-static struct resource sh_mmcif_resources[] = {
- [0] = {
- .name = "MMCIF",
- .start = 0xe6bd0000,
- .end = 0xe6bd00ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(140),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = gic_spi(141),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct sh_mmcif_plat_data sh_mmcif_platdata = {
- .ocr = MMC_VDD_165_195,
- .caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
- .ccs_unsupported = true,
- .slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
- .slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
-};
-
-static struct platform_device mmc_device = {
- .name = "sh_mmcif",
- .dev = {
- .dma_mask = NULL,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = &sh_mmcif_platdata,
- },
- .num_resources = ARRAY_SIZE(sh_mmcif_resources),
- .resource = sh_mmcif_resources,
-};
-
-/* Fixed 3.3V regulators to be used by SDHI0 */
-static struct regulator_consumer_supply vcc_sdhi0_consumers[] =
-{
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vcc_sdhi0_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
- .consumer_supplies = vcc_sdhi0_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi0_info = {
- .supply_name = "SDHI0 Vcc",
- .microvolts = 3300000,
- .gpio = 15,
- .enable_high = 1,
- .init_data = &vcc_sdhi0_init_data,
-};
-
-static struct platform_device vcc_sdhi0 = {
- .name = "reg-fixed-voltage",
- .id = 0,
- .dev = {
- .platform_data = &vcc_sdhi0_info,
- },
-};
-
-/* Fixed 3.3V regulators to be used by SDHI2 */
-static struct regulator_consumer_supply vcc_sdhi2_consumers[] =
-{
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.2"),
-};
-
-static struct regulator_init_data vcc_sdhi2_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi2_consumers),
- .consumer_supplies = vcc_sdhi2_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi2_info = {
- .supply_name = "SDHI2 Vcc",
- .microvolts = 3300000,
- .gpio = 14,
- .enable_high = 1,
- .init_data = &vcc_sdhi2_init_data,
-};
-
-static struct platform_device vcc_sdhi2 = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &vcc_sdhi2_info,
- },
-};
-
-/* SDHI */
-static struct tmio_mmc_data sdhi0_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI0_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI0_RX,
- .flags = TMIO_MMC_HAS_IDLE_WAIT,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
- MMC_CAP_POWER_OFF_CARD,
-};
-
-static struct resource sdhi0_resources[] = {
- [0] = {
- .name = "SDHI0",
- .start = 0xee100000,
- .end = 0xee1000ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .name = SH_MOBILE_SDHI_IRQ_CARD_DETECT,
- .start = gic_spi(83),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .name = SH_MOBILE_SDHI_IRQ_SDCARD,
- .start = gic_spi(84),
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .name = SH_MOBILE_SDHI_IRQ_SDIO,
- .start = gic_spi(85),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi0_device = {
- .name = "sh_mobile_sdhi",
- .num_resources = ARRAY_SIZE(sdhi0_resources),
- .resource = sdhi0_resources,
- .dev = {
- .platform_data = &sdhi0_info,
- },
-};
-
-/* Micro SD */
-static struct tmio_mmc_data sdhi2_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI2_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI2_RX,
- .flags = TMIO_MMC_HAS_IDLE_WAIT |
- TMIO_MMC_USE_GPIO_CD |
- TMIO_MMC_WRPROTECT_DISABLE,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_POWER_OFF_CARD,
- .cd_gpio = 13,
-};
-
-static struct resource sdhi2_resources[] = {
- [0] = {
- .name = "SDHI2",
- .start = 0xee140000,
- .end = 0xee1400ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .name = SH_MOBILE_SDHI_IRQ_CARD_DETECT,
- .start = gic_spi(103),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .name = SH_MOBILE_SDHI_IRQ_SDCARD,
- .start = gic_spi(104),
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .name = SH_MOBILE_SDHI_IRQ_SDIO,
- .start = gic_spi(105),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi2_device = {
- .name = "sh_mobile_sdhi",
- .id = 2,
- .num_resources = ARRAY_SIZE(sdhi2_resources),
- .resource = sdhi2_resources,
- .dev = {
- .platform_data = &sdhi2_info,
- },
-};
-
-/* KEY */
-#define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
-
-static struct gpio_keys_button gpio_buttons[] = {
- GPIO_KEY(KEY_BACK, GPIO_PCF8575_PORT10, "SW3"),
- GPIO_KEY(KEY_RIGHT, GPIO_PCF8575_PORT11, "SW2-R"),
- GPIO_KEY(KEY_LEFT, GPIO_PCF8575_PORT12, "SW2-L"),
- GPIO_KEY(KEY_ENTER, GPIO_PCF8575_PORT13, "SW2-P"),
- GPIO_KEY(KEY_UP, GPIO_PCF8575_PORT14, "SW2-U"),
- GPIO_KEY(KEY_DOWN, GPIO_PCF8575_PORT15, "SW2-D"),
- GPIO_KEY(KEY_HOME, GPIO_PCF8575_PORT16, "SW1"),
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device gpio_keys_device = {
- .name = "gpio-keys",
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-/* FSI-AK4648 */
-static struct sh_fsi_platform_info fsi_info = {
- .port_a = {
- .tx_id = SHDMA_SLAVE_FSI2A_TX,
- },
-};
-
-static struct resource fsi_resources[] = {
- [0] = {
- .name = "FSI",
- .start = 0xEC230000,
- .end = 0xEC230400 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(146),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device fsi_device = {
- .name = "sh_fsi2",
- .id = -1,
- .num_resources = ARRAY_SIZE(fsi_resources),
- .resource = fsi_resources,
- .dev = {
- .platform_data = &fsi_info,
- },
-};
-
-static struct asoc_simple_card_info fsi2_ak4648_info = {
- .name = "AK4648",
- .card = "FSI2A-AK4648",
- .codec = "ak4642-codec.0-0012",
- .platform = "sh_fsi2",
- .daifmt = SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_CBM_CFM,
- .cpu_dai = {
- .name = "fsia-dai",
- },
- .codec_dai = {
- .name = "ak4642-hifi",
- .sysclk = 11289600,
- },
-};
-
-static struct platform_device fsi_ak4648_device = {
- .name = "asoc-simple-card",
- .dev = {
- .platform_data = &fsi2_ak4648_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .dma_mask = &fsi_ak4648_device.dev.coherent_dma_mask,
- },
-};
-
-/* I2C */
-
-/* StepDown1 is used to supply 1.315V to the CPU */
-static struct regulator_init_data as3711_sd1 = {
- .constraints = {
- .name = "1.315V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1315000,
- .max_uV = 1335000,
- },
-};
-
-/* StepDown2 is used to supply 1.8V to the CPU and to the board */
-static struct regulator_init_data as3711_sd2 = {
- .constraints = {
- .name = "1.8V",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1800000,
- .max_uV = 1800000,
- },
-};
-
-/*
- * StepDown3 is switched in parallel with StepDown2, seems to be off,
- * according to read-back pre-set register values
- */
-
-/* StepDown4 is used to supply 1.215V to the CPU and to the board */
-static struct regulator_init_data as3711_sd4 = {
- .constraints = {
- .name = "1.215V",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1215000,
- .max_uV = 1235000,
- },
-};
-
-/* LDO1 is unused and unconnected */
-
-/* LDO2 is used to supply 2.8V to the CPU */
-static struct regulator_init_data as3711_ldo2 = {
- .constraints = {
- .name = "2.8V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 2800000,
- .max_uV = 2800000,
- },
-};
-
-/* LDO3 is used to supply 3.0V to the CPU */
-static struct regulator_init_data as3711_ldo3 = {
- .constraints = {
- .name = "3.0V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 3000000,
- .max_uV = 3000000,
- },
-};
-
-/* LDO4 is used to supply 2.8V to the board */
-static struct regulator_init_data as3711_ldo4 = {
- .constraints = {
- .name = "2.8V",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 2800000,
- .max_uV = 2800000,
- },
-};
-
-/* LDO5 is switched parallel to LDO4, also set to 2.8V */
-static struct regulator_init_data as3711_ldo5 = {
- .constraints = {
- .name = "2.8V #2",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 2800000,
- .max_uV = 2800000,
- },
-};
-
-/* LDO6 is unused and unconnected */
-
-/* LDO7 is used to supply 1.15V to the CPU */
-static struct regulator_init_data as3711_ldo7 = {
- .constraints = {
- .name = "1.15V CPU",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1150000,
- .max_uV = 1150000,
- },
-};
-
-/* LDO8 is switched parallel to LDO7, also set to 1.15V */
-static struct regulator_init_data as3711_ldo8 = {
- .constraints = {
- .name = "1.15V CPU #2",
- .boot_on = 1,
- .always_on = 1,
- .min_uV = 1150000,
- .max_uV = 1150000,
- },
-};
-
-static struct as3711_platform_data as3711_pdata = {
- .regulator = {
- .init_data = {
- [AS3711_REGULATOR_SD_1] = &as3711_sd1,
- [AS3711_REGULATOR_SD_2] = &as3711_sd2,
- [AS3711_REGULATOR_SD_4] = &as3711_sd4,
- [AS3711_REGULATOR_LDO_2] = &as3711_ldo2,
- [AS3711_REGULATOR_LDO_3] = &as3711_ldo3,
- [AS3711_REGULATOR_LDO_4] = &as3711_ldo4,
- [AS3711_REGULATOR_LDO_5] = &as3711_ldo5,
- [AS3711_REGULATOR_LDO_7] = &as3711_ldo7,
- [AS3711_REGULATOR_LDO_8] = &as3711_ldo8,
- },
- },
- .backlight = {
- .su2_fb = "sh_mobile_lcdc_fb.0",
- .su2_max_uA = 36000,
- .su2_feedback = AS3711_SU2_CURR_AUTO,
- .su2_fbprot = AS3711_SU2_GPIO4,
- .su2_auto_curr1 = true,
- .su2_auto_curr2 = true,
- .su2_auto_curr3 = true,
- },
-};
-
-static struct pcf857x_platform_data pcf8575_pdata = {
- .gpio_base = GPIO_PCF8575_BASE,
-};
-
-static struct i2c_board_info i2c0_devices[] = {
- {
- I2C_BOARD_INFO("ak4648", 0x12),
- },
- {
- I2C_BOARD_INFO("r2025sd", 0x32),
- },
- {
- I2C_BOARD_INFO("ak8975", 0x0c),
- .irq = irq_pin(28), /* IRQ28 */
- },
- {
- I2C_BOARD_INFO("adxl34x", 0x1d),
- .irq = irq_pin(26), /* IRQ26 */
- },
- {
- I2C_BOARD_INFO("as3711", 0x40),
- .irq = intcs_evt2irq(0x3300), /* IRQ24 */
- .platform_data = &as3711_pdata,
- },
-};
-
-static struct i2c_board_info i2c1_devices[] = {
- {
- I2C_BOARD_INFO("st1232-ts", 0x55),
- .irq = irq_pin(8), /* IRQ8 */
- },
-};
-
-static struct i2c_board_info i2c3_devices[] = {
- {
- I2C_BOARD_INFO("pcf8575", 0x20),
- .irq = irq_pin(19), /* IRQ19 */
- .platform_data = &pcf8575_pdata,
- },
-};
-
-static struct platform_device *kzm_devices[] __initdata = {
- &smsc_device,
- &usb_host_device,
- &usbhs_device,
- &lcdc_device,
- &mmc_device,
- &vcc_sdhi0,
- &vcc_sdhi2,
- &sdhi0_device,
- &sdhi2_device,
- &gpio_keys_device,
- &fsi_device,
- &fsi_ak4648_device,
-};
-
-static unsigned long pin_pullup_conf[] = {
- PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 0),
-};
-
-static const struct pinctrl_map kzm_pinctrl_map[] = {
- /* FSIA (AK4648) */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_mclk_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_sclk_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_data_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
- "fsia_data_out", "fsia"),
- /* I2C3 */
- PIN_MAP_MUX_GROUP_DEFAULT("i2c-sh_mobile.3", "pfc-sh73a0",
- "i2c3_1", "i2c3"),
- /* LCD */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh73a0",
- "lcd_data24", "lcd"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh73a0",
- "lcd_sync", "lcd"),
- /* MMCIF */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "mmc0_data8_0", "mmc0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "mmc0_ctrl_0", "mmc0"),
- PIN_MAP_CONFIGS_PIN_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "PORT279", pin_pullup_conf),
- PIN_MAP_CONFIGS_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
- "mmc0_data8_0", pin_pullup_conf),
- /* SCIFA4 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.4", "pfc-sh73a0",
- "scifa4_data", "scifa4"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.4", "pfc-sh73a0",
- "scifa4_ctrl", "scifa4"),
- /* SDHI0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_data4", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_ctrl", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_cd", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
- "sdhi0_wp", "sdhi0"),
- /* SDHI2 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.2", "pfc-sh73a0",
- "sdhi2_data4", "sdhi2"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.2", "pfc-sh73a0",
- "sdhi2_ctrl", "sdhi2"),
- /* SMSC */
- PIN_MAP_MUX_GROUP_DEFAULT("smsc911x.0", "pfc-sh73a0",
- "bsc_cs4", "bsc"),
- /* USB */
- PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-sh73a0",
- "usb_vbus", "usb"),
-};
-
-static void __init kzm_init(void)
-{
- regulator_register_always_on(2, "fixed-1.8V", fixed1v8_power_consumers,
- ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
- regulator_register_fixed(3, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- pinctrl_register_mappings(kzm_pinctrl_map, ARRAY_SIZE(kzm_pinctrl_map));
-
- sh73a0_pinmux_init();
-
- /* SMSC */
- gpio_request_one(224, GPIOF_IN, NULL); /* IRQ3 */
-
- /* LCDC */
- gpio_request_one(222, GPIOF_OUT_INIT_HIGH, NULL); /* LCDCDON */
- gpio_request_one(226, GPIOF_OUT_INIT_HIGH, NULL); /* SC */
-
- /* Touchscreen */
- gpio_request_one(223, GPIOF_IN, NULL); /* IRQ8 */
-
-#ifdef CONFIG_CACHE_L2X0
- /* Shared attribute override enable, 64K*8way */
- l2x0_init(IOMEM(0xf0100000), 0x00400000, 0xc20f0fff);
-#endif
-
- i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
- i2c_register_board_info(1, i2c1_devices, ARRAY_SIZE(i2c1_devices));
- i2c_register_board_info(3, i2c3_devices, ARRAY_SIZE(i2c3_devices));
-
- sh73a0_add_standard_devices();
- platform_add_devices(kzm_devices, ARRAY_SIZE(kzm_devices));
-
- sh73a0_pm_init();
-}
-
-static void kzm9g_restart(enum reboot_mode mode, const char *cmd)
-{
-#define RESCNT2 IOMEM(0xe6188020)
- /* Do soft power on reset */
- writel((1 << 31), RESCNT2);
-}
-
-static const char *kzm9g_boards_compat_dt[] __initdata = {
- "renesas,kzm9g",
- NULL,
-};
-
-DT_MACHINE_START(KZM9G_DT, "kzm9g")
- .smp = smp_ops(sh73a0_smp_ops),
- .map_io = sh73a0_map_io,
- .init_early = sh73a0_add_early_devices,
- .init_irq = sh73a0_init_irq,
- .init_machine = kzm_init,
- .init_late = shmobile_init_late,
- .init_time = sh73a0_earlytimer_init,
- .restart = kzm9g_restart,
- .dt_compat = kzm9g_boards_compat_dt,
-MACHINE_END
diff --git a/arch/arm/mach-shmobile/include/mach/head-kzm9g.txt b/arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
deleted file mode 100644
index 9531f46a822a1b22..0000000000000000
--- a/arch/arm/mach-shmobile/include/mach/head-kzm9g.txt
+++ /dev/null
@@ -1,410 +0,0 @@
-LIST "KZM9G low-level initialization routine."
-LIST "Adapted from u-boot KZM9G support code."
-
-LIST "Copyright (C) 2013 Ulrich Hecht"
-
-LIST "This program is free software; you can redistribute it and/or modify"
-LIST "it under the terms of the GNU General Public License version 2 as"
-LIST "published by the Free Software Foundation."
-
-LIST "This program is distributed in the hope that it will be useful,"
-LIST "but WITHOUT ANY WARRANTY; without even the implied warranty of"
-LIST "MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the"
-LIST "GNU General Public License for more details."
-
-
-LIST "Register definitions:"
-
-LIST "Secure control register"
-#define LIFEC_SEC_SRC (0xE6110008)
-
-LIST "RWDT"
-#define RWDT_BASE (0xE6020000)
-#define RWTCSRA0 (RWDT_BASE + 0x04)
-
-LIST "HPB Semaphore Control Registers"
-#define HPBSCR_BASE (0xE6000000)
-#define HPBCTRL6 (HPBSCR_BASE + 0x1030)
-
-#define SBSC1_BASE (0xFE400000)
-#define SDCR0A (SBSC1_BASE + 0x0008)
-#define SDCR1A (SBSC1_BASE + 0x000C)
-#define SDPCRA (SBSC1_BASE + 0x0010)
-#define SDCR0SA (SBSC1_BASE + 0x0018)
-#define SDCR1SA (SBSC1_BASE + 0x001C)
-#define RTCSRA (SBSC1_BASE + 0x0020)
-#define RTCORA (SBSC1_BASE + 0x0028)
-#define RTCORHA (SBSC1_BASE + 0x002C)
-#define SDWCRC0A (SBSC1_BASE + 0x0040)
-#define SDWCRC1A (SBSC1_BASE + 0x0044)
-#define SDWCR00A (SBSC1_BASE + 0x0048)
-#define SDWCR01A (SBSC1_BASE + 0x004C)
-#define SDWCR10A (SBSC1_BASE + 0x0050)
-#define SDWCR11A (SBSC1_BASE + 0x0054)
-#define SDWCR2A (SBSC1_BASE + 0x0060)
-#define SDWCRC2A (SBSC1_BASE + 0x0064)
-#define ZQCCRA (SBSC1_BASE + 0x0068)
-#define SDMRACR0A (SBSC1_BASE + 0x0084)
-#define SDMRTMPCRA (SBSC1_BASE + 0x008C)
-#define SDMRTMPMSKA (SBSC1_BASE + 0x0094)
-#define SDGENCNTA (SBSC1_BASE + 0x009C)
-#define SDDRVCR0A (SBSC1_BASE + 0x00B4)
-#define DLLCNT0A (SBSC1_BASE + 0x0354)
-
-#define SDMRA1 (0xFE500000)
-#define SDMRA2 (0xFE5C0000)
-#define SDMRA3 (0xFE504000)
-
-#define SBSC2_BASE (0xFB400000)
-#define SDCR0B (SBSC2_BASE + 0x0008)
-#define SDCR1B (SBSC2_BASE + 0x000C)
-#define SDPCRB (SBSC2_BASE + 0x0010)
-#define SDCR0SB (SBSC2_BASE + 0x0018)
-#define SDCR1SB (SBSC2_BASE + 0x001C)
-#define RTCSRB (SBSC2_BASE + 0x0020)
-#define RTCORB (SBSC2_BASE + 0x0028)
-#define RTCORHB (SBSC2_BASE + 0x002C)
-#define SDWCRC0B (SBSC2_BASE + 0x0040)
-#define SDWCRC1B (SBSC2_BASE + 0x0044)
-#define SDWCR00B (SBSC2_BASE + 0x0048)
-#define SDWCR01B (SBSC2_BASE + 0x004C)
-#define SDWCR10B (SBSC2_BASE + 0x0050)
-#define SDWCR11B (SBSC2_BASE + 0x0054)
-#define SDPDCR0B (SBSC2_BASE + 0x0058)
-#define SDWCR2B (SBSC2_BASE + 0x0060)
-#define SDWCRC2B (SBSC2_BASE + 0x0064)
-#define ZQCCRB (SBSC2_BASE + 0x0068)
-#define SDMRACR0B (SBSC2_BASE + 0x0084)
-#define SDMRTMPCRB (SBSC2_BASE + 0x008C)
-#define SDMRTMPMSKB (SBSC2_BASE + 0x0094)
-#define SDGENCNTB (SBSC2_BASE + 0x009C)
-#define DPHYCNT0B (SBSC2_BASE + 0x00A0)
-#define DPHYCNT1B (SBSC2_BASE + 0x00A4)
-#define DPHYCNT2B (SBSC2_BASE + 0x00A8)
-#define SDDRVCR0B (SBSC2_BASE + 0x00B4)
-#define DLLCNT0B (SBSC2_BASE + 0x0354)
-
-#define SDMRB1 (0xFB500000)
-#define SDMRB2 (0xFB5C0000)
-#define SDMRB3 (0xFB504000)
-
-#define CPG_BASE (0xE6150000)
-#define FRQCRA (CPG_BASE + 0x0000)
-#define FRQCRB (CPG_BASE + 0x0004)
-#define FRQCRD (CPG_BASE + 0x00E4)
-#define VCLKCR1 (CPG_BASE + 0x0008)
-#define VCLKCR2 (CPG_BASE + 0x000C)
-#define VCLKCR3 (CPG_BASE + 0x001C)
-#define ZBCKCR (CPG_BASE + 0x0010)
-#define FLCKCR (CPG_BASE + 0x0014)
-#define SD0CKCR (CPG_BASE + 0x0074)
-#define SD1CKCR (CPG_BASE + 0x0078)
-#define SD2CKCR (CPG_BASE + 0x007C)
-#define FSIACKCR (CPG_BASE + 0x0018)
-#define SUBCKCR (CPG_BASE + 0x0080)
-#define SPUACKCR (CPG_BASE + 0x0084)
-#define SPUVCKCR (CPG_BASE + 0x0094)
-#define MSUCKCR (CPG_BASE + 0x0088)
-#define HSICKCR (CPG_BASE + 0x008C)
-#define FSIBCKCR (CPG_BASE + 0x0090)
-#define MFCK1CR (CPG_BASE + 0x0098)
-#define MFCK2CR (CPG_BASE + 0x009C)
-#define DSITCKCR (CPG_BASE + 0x0060)
-#define DSI0PCKCR (CPG_BASE + 0x0064)
-#define DSI1PCKCR (CPG_BASE + 0x0068)
-#define DSI0PHYCR (CPG_BASE + 0x006C)
-#define DVFSCR3 (CPG_BASE + 0x0174)
-#define DVFSCR4 (CPG_BASE + 0x0178)
-#define DVFSCR5 (CPG_BASE + 0x017C)
-#define MPMODE (CPG_BASE + 0x00CC)
-
-#define PLLECR (CPG_BASE + 0x00D0)
-#define PLL0CR (CPG_BASE + 0x00D8)
-#define PLL1CR (CPG_BASE + 0x0028)
-#define PLL2CR (CPG_BASE + 0x002C)
-#define PLL3CR (CPG_BASE + 0x00DC)
-#define PLL0STPCR (CPG_BASE + 0x00F0)
-#define PLL1STPCR (CPG_BASE + 0x00C8)
-#define PLL2STPCR (CPG_BASE + 0x00F8)
-#define PLL3STPCR (CPG_BASE + 0x00FC)
-#define RMSTPCR0 (CPG_BASE + 0x0110)
-#define RMSTPCR1 (CPG_BASE + 0x0114)
-#define RMSTPCR2 (CPG_BASE + 0x0118)
-#define RMSTPCR3 (CPG_BASE + 0x011C)
-#define RMSTPCR4 (CPG_BASE + 0x0120)
-#define RMSTPCR5 (CPG_BASE + 0x0124)
-#define SMSTPCR0 (CPG_BASE + 0x0130)
-#define SMSTPCR2 (CPG_BASE + 0x0138)
-#define SMSTPCR3 (CPG_BASE + 0x013C)
-#define CPGXXCR4 (CPG_BASE + 0x0150)
-#define SRCR0 (CPG_BASE + 0x80A0)
-#define SRCR2 (CPG_BASE + 0x80B0)
-#define SRCR3 (CPG_BASE + 0x80A8)
-#define VREFCR (CPG_BASE + 0x00EC)
-#define PCLKCR (CPG_BASE + 0x1020)
-
-#define PORT32CR (0xE6051020)
-#define PORT33CR (0xE6051021)
-#define PORT34CR (0xE6051022)
-#define PORT35CR (0xE6051023)
-
-LIST "DRAM initialization code:"
-
-EW RWTCSRA0, 0xA507
-
-ED_AND LIFEC_SEC_SRC, 0xFFFF7FFF
-
-ED_AND SMSTPCR3,0xFFFF7FFF
-ED_AND SRCR3, 0xFFFF7FFF
-ED_AND SMSTPCR2,0xFFFBFFFF
-ED_AND SRCR2, 0xFFFBFFFF
-ED PLLECR, 0x00000000
-
-WAIT_MASK PLLECR, 0x00000F00, 0x00000000
-WAIT_MASK FRQCRB, 0x80000000, 0x00000000
-
-ED PLL0CR, 0x2D000000
-ED PLL1CR, 0x17100000
-ED FRQCRB, 0x96235880
-WAIT_MASK FRQCRB, 0x80000000, 0x00000000
-
-ED FLCKCR, 0x0000000B
-ED_AND SMSTPCR0, 0xFFFFFFFD
-
-ED_AND SRCR0, 0xFFFFFFFD
-ED 0xE6001628, 0x514
-ED 0xE6001648, 0x514
-ED 0xE6001658, 0x514
-ED 0xE6001678, 0x514
-
-ED DVFSCR4, 0x00092000
-ED DVFSCR5, 0x000000DC
-ED PLLECR, 0x00000000
-WAIT_MASK PLLECR, 0x00000F00, 0x00000000
-
-ED FRQCRA, 0x0012453C
-ED FRQCRB, 0x80431350
-WAIT_MASK FRQCRB, 0x80000000, 0x00000000
-ED FRQCRD, 0x00000B0B
-WAIT_MASK FRQCRD, 0x80000000, 0x00000000
-
-ED PCLKCR, 0x00000003
-ED VCLKCR1, 0x0000012F
-ED VCLKCR2, 0x00000119
-ED VCLKCR3, 0x00000119
-ED ZBCKCR, 0x00000002
-ED FLCKCR, 0x00000005
-ED SD0CKCR, 0x00000080
-ED SD1CKCR, 0x00000080
-ED SD2CKCR, 0x00000080
-ED FSIACKCR, 0x0000003F
-ED FSIBCKCR, 0x0000003F
-ED SUBCKCR, 0x00000080
-ED SPUACKCR, 0x0000000B
-ED SPUVCKCR, 0x0000000B
-ED MSUCKCR, 0x0000013F
-ED HSICKCR, 0x00000080
-ED MFCK1CR, 0x0000003F
-ED MFCK2CR, 0x0000003F
-ED DSITCKCR, 0x00000107
-ED DSI0PCKCR, 0x00000313
-ED DSI1PCKCR, 0x0000130D
-ED DSI0PHYCR, 0x2A800E0E
-ED PLL0CR, 0x1E000000
-ED PLL0CR, 0x2D000000
-ED PLL1CR, 0x17100000
-ED PLL2CR, 0x27000080
-ED PLL3CR, 0x1D000000
-ED PLL0STPCR, 0x00080000
-ED PLL1STPCR, 0x000120C0
-ED PLL2STPCR, 0x00012000
-ED PLL3STPCR, 0x00000030
-ED PLLECR, 0x0000000B
-WAIT_MASK PLLECR, 0x00000B00, 0x00000B00
-
-ED DVFSCR3, 0x000120F0
-ED MPMODE, 0x00000020
-ED VREFCR, 0x0000028A
-ED RMSTPCR0, 0xE4628087
-ED RMSTPCR1, 0xFFFFFFFF
-ED RMSTPCR2, 0x53FFFFFF
-ED RMSTPCR3, 0xFFFFFFFF
-ED RMSTPCR4, 0x00800D3D
-ED RMSTPCR5, 0xFFFFF3FF
-ED SMSTPCR2, 0x00000000
-ED SRCR2, 0x00040000
-ED_AND PLLECR, 0xFFFFFFF7
-WAIT_MASK PLLECR, 0x00000800, 0x00000000
-
-LIST "set SBSC operational"
-ED HPBCTRL6, 0x00000001
-WAIT_MASK HPBCTRL6, 0x00000001, 0x00000001
-
-LIST "set SBSC operating frequency"
-ED FRQCRD, 0x00001414
-WAIT_MASK FRQCRD, 0x80000000, 0x00000000
-ED PLL3CR, 0x1D000000
-ED_OR PLLECR, 0x00000008
-WAIT_MASK PLLECR, 0x00000800, 0x00000800
-
-LIST "enable DLL oscillation in DDRPHY"
-ED_OR DLLCNT0A, 0x00000002
-
-LIST "wait >= 100 ns"
-ED SDGENCNTA, 0x00000005
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "target LPDDR2 device settings"
-ED SDCR0A, 0xACC90159
-ED SDCR1A, 0x00010059
-ED SDWCRC0A, 0x50874114
-ED SDWCRC1A, 0x33199B37
-ED SDWCRC2A, 0x008F2313
-ED SDWCR00A, 0x31020707
-ED SDWCR01A, 0x0017040A
-ED SDWCR10A, 0x31020707
-ED SDWCR11A, 0x0017040A
-
-ED SDDRVCR0A, 0x055557ff
-
-ED SDWCR2A, 0x30000000
-
-LIST "drive CKE high"
-ED_OR SDPCRA, 0x00000080
-WAIT_MASK SDPCRA, 0x00000080, 0x00000080
-
-LIST "wait >= 200 us"
-ED SDGENCNTA, 0x00002710
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "issue reset command to LPDDR2 device"
-ED SDMRACR0A, 0x0000003F
-ED SDMRA1, 0x00000000
-
-LIST "wait >= 10 (or 1) us (docs inconsistent)"
-ED SDGENCNTA, 0x000001F4
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "MRW ZS initialization calibration command"
-ED SDMRACR0A, 0x0000FF0A
-ED SDMRA3, 0x00000000
-
-LIST "wait >= 1 us"
-ED SDGENCNTA, 0x00000032
-WAIT_MASK SDGENCNTA, 0xFFFFFFFF, 0x00000000
-
-LIST "specify operating mode in LPDDR2"
-ED SDMRACR0A, 0x00002201
-ED SDMRA1, 0x00000000
-ED SDMRACR0A, 0x00000402
-ED SDMRA1, 0x00000000
-ED SDMRACR0A, 0x00000203
-ED SDMRA1, 0x00000000
-
-LIST "initialize DDR interface"
-ED SDMRA2, 0x00000000
-
-LIST "temperature sensor control"
-ED SDMRTMPCRA, 0x88800004
-ED SDMRTMPMSKA,0x00000004
-
-LIST "auto-refreshing control"
-ED RTCORA, 0xA55A0032
-ED RTCORHA, 0xA55A000C
-ED RTCSRA, 0xA55A2048
-
-ED_OR SDCR0A, 0x00000800
-ED_OR SDCR1A, 0x00000400
-
-LIST "auto ZQ calibration control"
-ED ZQCCRA, 0xFFF20000
-
-ED_OR DLLCNT0B, 0x00000002
-ED SDGENCNTB, 0x00000005
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-
-ED SDCR0B, 0xACC90159
-ED SDCR1B, 0x00010059
-ED SDWCRC0B, 0x50874114
-ED SDWCRC1B, 0x33199B37
-ED SDWCRC2B, 0x008F2313
-ED SDWCR00B, 0x31020707
-ED SDWCR01B, 0x0017040A
-ED SDWCR10B, 0x31020707
-ED SDWCR11B, 0x0017040A
-ED SDDRVCR0B, 0x055557ff
-ED SDWCR2B, 0x30000000
-ED_OR SDPCRB, 0x00000080
-WAIT_MASK SDPCRB, 0x00000080, 0x00000080
-
-ED SDGENCNTB, 0x00002710
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-ED SDMRACR0B, 0x0000003F
-
-LIST "upstream u-boot writes to SDMRA1A for both SBSC 1 and 2, which does"
-LIST "not seem to make a lot of sense..."
-ED SDMRB1, 0x00000000
-
-ED SDGENCNTB, 0x000001F4
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-
-ED SDMRACR0B, 0x0000FF0A
-ED SDMRB3, 0x00000000
-ED SDGENCNTB, 0x00000032
-WAIT_MASK SDGENCNTB, 0xFFFFFFFF, 0x00000000
-
-ED SDMRACR0B, 0x00002201
-ED SDMRB1, 0x00000000
-ED SDMRACR0B, 0x00000402
-ED SDMRB1, 0x00000000
-ED SDMRACR0B, 0x00000203
-ED SDMRB1, 0x00000000
-ED SDMRB2, 0x00000000
-ED SDMRTMPCRB, 0x88800004
-ED SDMRTMPMSKB, 0x00000004
-ED RTCORB, 0xA55A0032
-ED RTCORHB, 0xA55A000C
-ED RTCSRB, 0xA55A2048
-ED_OR SDCR0B, 0x00000800
-ED_OR SDCR1B, 0x00000400
-ED ZQCCRB, 0xFFF20000
-ED_OR SDPDCR0B, 0x00030000
-ED DPHYCNT1B, 0xA5390000
-ED DPHYCNT0B, 0x00001200
-ED DPHYCNT1B, 0x07CE0000
-ED DPHYCNT0B, 0x00001247
-WAIT_MASK DPHYCNT2B, 0xFFFFFFFF, 0x07CE0000
-
-ED_AND SDPDCR0B, 0xFFFCFFFF
-
-ED FRQCRD, 0x00000B0B
-WAIT_MASK FRQCRD, 0x80000000, 0x00000000
-
-ED CPGXXCR4, 0xfffffffc
-
-LIST "Setup SCIF4 / workaround"
-EB PORT32CR, 0x12
-EB PORT33CR, 0x22
-EB PORT34CR, 0x12
-EB PORT35CR, 0x22
-
-EW 0xE6C80000, 0
-EB 0xE6C80004, 0x19
-EW 0xE6C80008, 0x0030
-EW 0xE6C80018, 0
-EW 0xE6C80030, 0x0014
-
-LIST "Magic to avoid hangs and corruption on DRAM writes."
-
-LIST "It has been observed that the system would most often hang while"
-LIST "decompressing the kernel, and if it didn't it would always write"
-LIST "a corrupt image to DRAM."
-LIST "This problem does not occur in u-boot, and the reason is that"
-LIST "u-boot performs an additional cache invalidation after setting up"
-LIST "the DRAM controller. Such an invalidation should not be necessary at"
-LIST "this point, and attempts at removing parts of the routine to arrive"
-LIST "at the minimal snippet of code necessary to avoid the DRAM stability"
-LIST "problem yielded the following:"
-
-MRC p15, 0, r0, c1, c0, 0
-MCR p15, 0, r0, c1, c0, 0
diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h
index 175ee05465da19eb..80f599f4b5ab5733 100644
--- a/arch/arm/mach-shmobile/include/mach/zboot.h
+++ b/arch/arm/mach-shmobile/include/mach/zboot.h
@@ -9,11 +9,6 @@
*
**************************************************/
-#ifdef CONFIG_MACH_KZM9G
-#define MEMORY_START 0x43000000
-#include "mach/head-kzm9g.txt"
-#else
#error "unsupported board."
-#endif
#endif /* ZBOOT_H */
diff --git a/arch/arm/mach-shmobile/intc-sh73a0.c b/arch/arm/mach-shmobile/intc-sh73a0.c
deleted file mode 100644
index fd63ae6532fc9ab2..0000000000000000
--- a/arch/arm/mach-shmobile/intc-sh73a0.c
+++ /dev/null
@@ -1,337 +0,0 @@
-/*
- * sh73a0 processor support - INTC hardware block
- *
- * Copyright (C) 2010 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <linux/irqchip.h>
-#include <linux/irqchip/arm-gic.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "intc.h"
-#include "irqs.h"
-#include "sh73a0.h"
-
-enum {
- UNUSED = 0,
-
- /* interrupt sources INTCS */
- PINTCS_PINT1, PINTCS_PINT2,
- RTDMAC_0_DEI0, RTDMAC_0_DEI1, RTDMAC_0_DEI2, RTDMAC_0_DEI3,
- CEU, MFI, BBIF2, VPU, TSIF1, _3DG_SGX543, _2DDMAC_2DDM0,
- RTDMAC_1_DEI4, RTDMAC_1_DEI5, RTDMAC_1_DADERR,
- KEYSC_KEY, VINT, MSIOF,
- TMU0_TUNI00, TMU0_TUNI01, TMU0_TUNI02,
- CMT0, TSIF0, CMT2, LMB, MSUG, MSU_MSU, MSU_MSU2,
- CTI, RWDT0, ICB, PEP, ASA, JPU_JPEG, LCDC, LCRC,
- RTDMAC_2_DEI6, RTDMAC_2_DEI7, RTDMAC_2_DEI8, RTDMAC_2_DEI9,
- RTDMAC_3_DEI10, RTDMAC_3_DEI11,
- FRC, GCU, LCDC1, CSIRX,
- DSITX0_DSITX00, DSITX0_DSITX01,
- SPU2_SPU0, SPU2_SPU1, FSI,
- TMU1_TUNI10, TMU1_TUNI11, TMU1_TUNI12,
- TSIF2, CMT4, MFIS2, CPORTS2R, TSG, DMASCH1, SCUW,
- VIO60, VIO61, CEU21, CSI21, DSITX1_DSITX10, DSITX1_DSITX11,
- DISP, DSRV, EMUX2_EMUX20I, EMUX2_EMUX21I,
- MSTIF0_MST00I, MSTIF0_MST01I, MSTIF1_MST10I, MSTIF1_MST11I,
- SPUV,
-
- /* interrupt groups INTCS */
- RTDMAC_0, RTDMAC_1, RTDMAC_2, RTDMAC_3,
- DSITX0, SPU2, TMU1, MSU,
-};
-
-static struct intc_vect intcs_vectors[] = {
- INTCS_VECT(PINTCS_PINT1, 0x0600), INTCS_VECT(PINTCS_PINT2, 0x0620),
- INTCS_VECT(RTDMAC_0_DEI0, 0x0800), INTCS_VECT(RTDMAC_0_DEI1, 0x0820),
- INTCS_VECT(RTDMAC_0_DEI2, 0x0840), INTCS_VECT(RTDMAC_0_DEI3, 0x0860),
- INTCS_VECT(CEU, 0x0880), INTCS_VECT(MFI, 0x0900),
- INTCS_VECT(BBIF2, 0x0960), INTCS_VECT(VPU, 0x0980),
- INTCS_VECT(TSIF1, 0x09a0), INTCS_VECT(_3DG_SGX543, 0x09e0),
- INTCS_VECT(_2DDMAC_2DDM0, 0x0a00),
- INTCS_VECT(RTDMAC_1_DEI4, 0x0b80), INTCS_VECT(RTDMAC_1_DEI5, 0x0ba0),
- INTCS_VECT(RTDMAC_1_DADERR, 0x0bc0),
- INTCS_VECT(KEYSC_KEY, 0x0be0), INTCS_VECT(VINT, 0x0c80),
- INTCS_VECT(MSIOF, 0x0d20),
- INTCS_VECT(TMU0_TUNI00, 0x0e80), INTCS_VECT(TMU0_TUNI01, 0x0ea0),
- INTCS_VECT(TMU0_TUNI02, 0x0ec0),
- INTCS_VECT(CMT0, 0x0f00), INTCS_VECT(TSIF0, 0x0f20),
- INTCS_VECT(CMT2, 0x0f40), INTCS_VECT(LMB, 0x0f60),
- INTCS_VECT(MSUG, 0x0f80),
- INTCS_VECT(MSU_MSU, 0x0fa0), INTCS_VECT(MSU_MSU2, 0x0fc0),
- INTCS_VECT(CTI, 0x0400), INTCS_VECT(RWDT0, 0x0440),
- INTCS_VECT(ICB, 0x0480), INTCS_VECT(PEP, 0x04a0),
- INTCS_VECT(ASA, 0x04c0), INTCS_VECT(JPU_JPEG, 0x0560),
- INTCS_VECT(LCDC, 0x0580), INTCS_VECT(LCRC, 0x05a0),
- INTCS_VECT(RTDMAC_2_DEI6, 0x1300), INTCS_VECT(RTDMAC_2_DEI7, 0x1320),
- INTCS_VECT(RTDMAC_2_DEI8, 0x1340), INTCS_VECT(RTDMAC_2_DEI9, 0x1360),
- INTCS_VECT(RTDMAC_3_DEI10, 0x1380), INTCS_VECT(RTDMAC_3_DEI11, 0x13a0),
- INTCS_VECT(FRC, 0x1700), INTCS_VECT(GCU, 0x1760),
- INTCS_VECT(LCDC1, 0x1780), INTCS_VECT(CSIRX, 0x17a0),
- INTCS_VECT(DSITX0_DSITX00, 0x17c0), INTCS_VECT(DSITX0_DSITX01, 0x17e0),
- INTCS_VECT(SPU2_SPU0, 0x1800), INTCS_VECT(SPU2_SPU1, 0x1820),
- INTCS_VECT(FSI, 0x1840),
- INTCS_VECT(TMU1_TUNI10, 0x1900), INTCS_VECT(TMU1_TUNI11, 0x1920),
- INTCS_VECT(TMU1_TUNI12, 0x1940),
- INTCS_VECT(TSIF2, 0x1960), INTCS_VECT(CMT4, 0x1980),
- INTCS_VECT(MFIS2, 0x1a00), INTCS_VECT(CPORTS2R, 0x1a20),
- INTCS_VECT(TSG, 0x1ae0), INTCS_VECT(DMASCH1, 0x1b00),
- INTCS_VECT(SCUW, 0x1b40),
- INTCS_VECT(VIO60, 0x1b60), INTCS_VECT(VIO61, 0x1b80),
- INTCS_VECT(CEU21, 0x1ba0), INTCS_VECT(CSI21, 0x1be0),
- INTCS_VECT(DSITX1_DSITX10, 0x1c00), INTCS_VECT(DSITX1_DSITX11, 0x1c20),
- INTCS_VECT(DISP, 0x1c40), INTCS_VECT(DSRV, 0x1c60),
- INTCS_VECT(EMUX2_EMUX20I, 0x1c80), INTCS_VECT(EMUX2_EMUX21I, 0x1ca0),
- INTCS_VECT(MSTIF0_MST00I, 0x1cc0), INTCS_VECT(MSTIF0_MST01I, 0x1ce0),
- INTCS_VECT(MSTIF1_MST10I, 0x1d00), INTCS_VECT(MSTIF1_MST11I, 0x1d20),
- INTCS_VECT(SPUV, 0x2300),
-};
-
-static struct intc_group intcs_groups[] __initdata = {
- INTC_GROUP(RTDMAC_0, RTDMAC_0_DEI0, RTDMAC_0_DEI1,
- RTDMAC_0_DEI2, RTDMAC_0_DEI3),
- INTC_GROUP(RTDMAC_1, RTDMAC_1_DEI4, RTDMAC_1_DEI5, RTDMAC_1_DADERR),
- INTC_GROUP(RTDMAC_2, RTDMAC_2_DEI6, RTDMAC_2_DEI7,
- RTDMAC_2_DEI8, RTDMAC_2_DEI9),
- INTC_GROUP(RTDMAC_3, RTDMAC_3_DEI10, RTDMAC_3_DEI11),
- INTC_GROUP(TMU1, TMU1_TUNI12, TMU1_TUNI11, TMU1_TUNI10),
- INTC_GROUP(DSITX0, DSITX0_DSITX00, DSITX0_DSITX01),
- INTC_GROUP(SPU2, SPU2_SPU0, SPU2_SPU1),
- INTC_GROUP(MSU, MSU_MSU, MSU_MSU2),
-};
-
-static struct intc_mask_reg intcs_mask_registers[] = {
- { 0xffd20184, 0xffd201c4, 8, /* IMR1SA / IMCR1SA */
- { 0, 0, 0, CEU,
- 0, 0, 0, 0 } },
- { 0xffd20188, 0xffd201c8, 8, /* IMR2SA / IMCR2SA */
- { 0, 0, 0, VPU,
- BBIF2, 0, 0, MFI } },
- { 0xffd2018c, 0xffd201cc, 8, /* IMR3SA / IMCR3SA */
- { 0, 0, 0, _2DDMAC_2DDM0,
- 0, ASA, PEP, ICB } },
- { 0xffd20190, 0xffd201d0, 8, /* IMR4SA / IMCR4SA */
- { 0, 0, 0, CTI,
- JPU_JPEG, 0, LCRC, LCDC } },
- { 0xffd20194, 0xffd201d4, 8, /* IMR5SA / IMCR5SA */
- { KEYSC_KEY, RTDMAC_1_DADERR, RTDMAC_1_DEI5, RTDMAC_1_DEI4,
- RTDMAC_0_DEI3, RTDMAC_0_DEI2, RTDMAC_0_DEI1, RTDMAC_0_DEI0 } },
- { 0xffd20198, 0xffd201d8, 8, /* IMR6SA / IMCR6SA */
- { 0, 0, MSIOF, 0,
- _3DG_SGX543, 0, 0, 0 } },
- { 0xffd2019c, 0xffd201dc, 8, /* IMR7SA / IMCR7SA */
- { 0, TMU0_TUNI02, TMU0_TUNI01, TMU0_TUNI00,
- 0, 0, 0, 0 } },
- { 0xffd201a0, 0xffd201e0, 8, /* IMR8SA / IMCR8SA */
- { 0, 0, 0, 0,
- 0, MSU_MSU, MSU_MSU2, MSUG } },
- { 0xffd201a4, 0xffd201e4, 8, /* IMR9SA / IMCR9SA */
- { 0, RWDT0, CMT2, CMT0,
- 0, 0, 0, 0 } },
- { 0xffd201ac, 0xffd201ec, 8, /* IMR11SA / IMCR11SA */
- { 0, 0, 0, 0,
- 0, TSIF1, LMB, TSIF0 } },
- { 0xffd201b0, 0xffd201f0, 8, /* IMR12SA / IMCR12SA */
- { 0, 0, 0, 0,
- 0, 0, PINTCS_PINT2, PINTCS_PINT1 } },
- { 0xffd50180, 0xffd501c0, 8, /* IMR0SA3 / IMCR0SA3 */
- { RTDMAC_2_DEI6, RTDMAC_2_DEI7, RTDMAC_2_DEI8, RTDMAC_2_DEI9,
- RTDMAC_3_DEI10, RTDMAC_3_DEI11, 0, 0 } },
- { 0xffd50190, 0xffd501d0, 8, /* IMR4SA3 / IMCR4SA3 */
- { FRC, 0, 0, GCU,
- LCDC1, CSIRX, DSITX0_DSITX00, DSITX0_DSITX01 } },
- { 0xffd50194, 0xffd501d4, 8, /* IMR5SA3 / IMCR5SA3 */
- { SPU2_SPU0, SPU2_SPU1, FSI, 0,
- 0, 0, 0, 0 } },
- { 0xffd50198, 0xffd501d8, 8, /* IMR6SA3 / IMCR6SA3 */
- { TMU1_TUNI10, TMU1_TUNI11, TMU1_TUNI12, 0,
- TSIF2, CMT4, 0, 0 } },
- { 0xffd5019c, 0xffd501dc, 8, /* IMR7SA3 / IMCR7SA3 */
- { MFIS2, CPORTS2R, 0, 0,
- 0, 0, 0, TSG } },
- { 0xffd501a0, 0xffd501e0, 8, /* IMR8SA3 / IMCR8SA3 */
- { DMASCH1, 0, SCUW, VIO60,
- VIO61, CEU21, 0, CSI21 } },
- { 0xffd501a4, 0xffd501e4, 8, /* IMR9SA3 / IMCR9SA3 */
- { DSITX1_DSITX10, DSITX1_DSITX11, DISP, DSRV,
- EMUX2_EMUX20I, EMUX2_EMUX21I, MSTIF0_MST00I, MSTIF0_MST01I } },
- { 0xffd501a8, 0xffd501e8, 8, /* IMR10SA3 / IMCR10SA3 */
- { MSTIF0_MST00I, MSTIF0_MST01I, 0, 0,
- 0, 0, 0, 0 } },
- { 0xffd60180, 0xffd601c0, 8, /* IMR0SA4 / IMCR0SA4 */
- { SPUV, 0, 0, 0,
- 0, 0, 0, 0 } },
-};
-
-/* Priority is needed for INTCA to receive the INTCS interrupt */
-static struct intc_prio_reg intcs_prio_registers[] = {
- { 0xffd20000, 0, 16, 4, /* IPRAS */ { CTI, 0, _2DDMAC_2DDM0, ICB } },
- { 0xffd20004, 0, 16, 4, /* IPRBS */ { JPU_JPEG, LCDC, 0, LCRC } },
- { 0xffd20008, 0, 16, 4, /* IPRCS */ { BBIF2, 0, 0, 0 } },
- { 0xffd2000c, 0, 16, 4, /* IPRDS */ { PINTCS_PINT1, PINTCS_PINT2,
- 0, 0 } },
- { 0xffd20010, 0, 16, 4, /* IPRES */ { RTDMAC_0, CEU, MFI, VPU } },
- { 0xffd20014, 0, 16, 4, /* IPRFS */ { KEYSC_KEY, RTDMAC_1,
- CMT2, CMT0 } },
- { 0xffd20018, 0, 16, 4, /* IPRGS */ { TMU0_TUNI00, TMU0_TUNI01,
- TMU0_TUNI02, TSIF1 } },
- { 0xffd2001c, 0, 16, 4, /* IPRHS */ { VINT, 0, 0, 0 } },
- { 0xffd20020, 0, 16, 4, /* IPRIS */ { 0, MSIOF, TSIF0, 0 } },
- { 0xffd20024, 0, 16, 4, /* IPRJS */ { 0, _3DG_SGX543, MSUG, MSU } },
- { 0xffd20028, 0, 16, 4, /* IPRKS */ { 0, ASA, LMB, PEP } },
- { 0xffd20030, 0, 16, 4, /* IPRMS */ { 0, 0, 0, RWDT0 } },
- { 0xffd50000, 0, 16, 4, /* IPRAS3 */ { RTDMAC_2, 0, 0, 0 } },
- { 0xffd50004, 0, 16, 4, /* IPRBS3 */ { RTDMAC_3, 0, 0, 0 } },
- { 0xffd50020, 0, 16, 4, /* IPRIS3 */ { FRC, 0, 0, 0 } },
- { 0xffd50024, 0, 16, 4, /* IPRJS3 */ { LCDC1, CSIRX, DSITX0, 0 } },
- { 0xffd50028, 0, 16, 4, /* IPRKS3 */ { SPU2, 0, FSI, 0 } },
- { 0xffd50030, 0, 16, 4, /* IPRMS3 */ { TMU1, 0, 0, TSIF2 } },
- { 0xffd50034, 0, 16, 4, /* IPRNS3 */ { CMT4, 0, 0, 0 } },
- { 0xffd50038, 0, 16, 4, /* IPROS3 */ { MFIS2, CPORTS2R, 0, 0 } },
- { 0xffd50040, 0, 16, 4, /* IPRQS3 */ { DMASCH1, 0, SCUW, VIO60 } },
- { 0xffd50044, 0, 16, 4, /* IPRRS3 */ { VIO61, CEU21, 0, CSI21 } },
- { 0xffd50048, 0, 16, 4, /* IPRSS3 */ { DSITX1_DSITX10, DSITX1_DSITX11,
- DISP, DSRV } },
- { 0xffd5004c, 0, 16, 4, /* IPRTS3 */ { EMUX2_EMUX20I, EMUX2_EMUX21I,
- MSTIF0_MST00I, MSTIF0_MST01I } },
- { 0xffd50050, 0, 16, 4, /* IPRUS3 */ { MSTIF1_MST10I, MSTIF1_MST11I,
- 0, 0 } },
- { 0xffd60000, 0, 16, 4, /* IPRAS4 */ { SPUV, 0, 0, 0 } },
-};
-
-static struct resource intcs_resources[] __initdata = {
- [0] = {
- .start = 0xffd20000,
- .end = 0xffd201ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = 0xffd50000,
- .end = 0xffd501ff,
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .start = 0xffd60000,
- .end = 0xffd601ff,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct intc_desc intcs_desc __initdata = {
- .name = "sh73a0-intcs",
- .resource = intcs_resources,
- .num_resources = ARRAY_SIZE(intcs_resources),
- .hw = INTC_HW_DESC(intcs_vectors, intcs_groups, intcs_mask_registers,
- intcs_prio_registers, NULL, NULL),
-};
-
-static struct irqaction sh73a0_intcs_cascade;
-
-static irqreturn_t sh73a0_intcs_demux(int irq, void *dev_id)
-{
- unsigned int evtcodeas = ioread32((void __iomem *)dev_id);
-
- generic_handle_irq(intcs_evt2irq(evtcodeas));
-
- return IRQ_HANDLED;
-}
-
-#define PINTER0_PHYS 0xe69000a0
-#define PINTER1_PHYS 0xe69000a4
-#define PINTER0_VIRT IOMEM(0xe69000a0)
-#define PINTER1_VIRT IOMEM(0xe69000a4)
-#define PINTRR0 IOMEM(0xe69000d0)
-#define PINTRR1 IOMEM(0xe69000d4)
-
-#define PINT0A_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq))
-#define PINT0B_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq + 8))
-#define PINT0C_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq + 16))
-#define PINT0D_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT0_IRQ(irq + 24))
-#define PINT1E_IRQ(n, irq) INTC_IRQ((n), SH73A0_PINT1_IRQ(irq))
-
-INTC_PINT(intc_pint0, PINTER0_PHYS, 0xe69000b0, "sh73a0-pint0", \
- INTC_PINT_E(A), INTC_PINT_E(B), INTC_PINT_E(C), INTC_PINT_E(D), \
- INTC_PINT_V(A, PINT0A_IRQ), INTC_PINT_V(B, PINT0B_IRQ), \
- INTC_PINT_V(C, PINT0C_IRQ), INTC_PINT_V(D, PINT0D_IRQ), \
- INTC_PINT_E(A), INTC_PINT_E(B), INTC_PINT_E(C), INTC_PINT_E(D), \
- INTC_PINT_E(A), INTC_PINT_E(B), INTC_PINT_E(C), INTC_PINT_E(D));
-
-INTC_PINT(intc_pint1, PINTER1_PHYS, 0xe69000c0, "sh73a0-pint1", \
- INTC_PINT_E(E), INTC_PINT_E_EMPTY, INTC_PINT_E_EMPTY, INTC_PINT_E_EMPTY, \
- INTC_PINT_V(E, PINT1E_IRQ), INTC_PINT_V_NONE, \
- INTC_PINT_V_NONE, INTC_PINT_V_NONE, \
- INTC_PINT_E_NONE, INTC_PINT_E_NONE, INTC_PINT_E_NONE, INTC_PINT_E(E), \
- INTC_PINT_E(E), INTC_PINT_E_NONE, INTC_PINT_E_NONE, INTC_PINT_E_NONE);
-
-static struct irqaction sh73a0_pint0_cascade;
-static struct irqaction sh73a0_pint1_cascade;
-
-static void pint_demux(void __iomem *rr, void __iomem *er, int base_irq)
-{
- unsigned long value = ioread32(rr) & ioread32(er);
- int k;
-
- for (k = 0; k < 32; k++) {
- if (value & (1 << (31 - k))) {
- generic_handle_irq(base_irq + k);
- iowrite32(~(1 << (31 - k)), rr);
- }
- }
-}
-
-static irqreturn_t sh73a0_pint0_demux(int irq, void *dev_id)
-{
- pint_demux(PINTRR0, PINTER0_VIRT, SH73A0_PINT0_IRQ(0));
- return IRQ_HANDLED;
-}
-
-static irqreturn_t sh73a0_pint1_demux(int irq, void *dev_id)
-{
- pint_demux(PINTRR1, PINTER1_VIRT, SH73A0_PINT1_IRQ(0));
- return IRQ_HANDLED;
-}
-
-void __init sh73a0_init_irq(void)
-{
- void __iomem *gic_dist_base = IOMEM(0xf0001000);
- void __iomem *gic_cpu_base = IOMEM(0xf0000100);
- void __iomem *intevtsa = ioremap_nocache(0xffd20100, PAGE_SIZE);
-
- gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE);
- gic_init(0, 29, gic_dist_base, gic_cpu_base);
-
- register_intc_controller(&intcs_desc);
- register_intc_controller(&intc_pint0_desc);
- register_intc_controller(&intc_pint1_desc);
-
- /* demux using INTEVTSA */
- sh73a0_intcs_cascade.name = "INTCS cascade";
- sh73a0_intcs_cascade.handler = sh73a0_intcs_demux;
- sh73a0_intcs_cascade.dev_id = intevtsa;
- setup_irq(gic_spi(50), &sh73a0_intcs_cascade);
-
- /* PINT pins are sanely tied to the GIC as SPI */
- sh73a0_pint0_cascade.name = "PINT0 cascade";
- sh73a0_pint0_cascade.handler = sh73a0_pint0_demux;
- setup_irq(gic_spi(33), &sh73a0_pint0_cascade);
-
- sh73a0_pint1_cascade.name = "PINT1 cascade";
- sh73a0_pint1_cascade.handler = sh73a0_pint1_demux;
- setup_irq(gic_spi(34), &sh73a0_pint1_cascade);
-}
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 02/15] ARM: shmobile: Remove legacy kzm9g_defconfig
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for KZM-A9-GT has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
MAINTAINERS | 1 -
arch/arm/configs/kzm9g_defconfig | 154 ---------------------------------------
2 files changed, 155 deletions(-)
delete mode 100644 arch/arm/configs/kzm9g_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index eaadc4a87d38bf64..f1fe0cc0dadee9df 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1457,7 +1457,6 @@ F: arch/arm/boot/dts/r8a*
F: arch/arm/boot/dts/sh*
F: arch/arm/configs/armadillo800eva_defconfig
F: arch/arm/configs/bockw_defconfig
-F: arch/arm/configs/kzm9g_defconfig
F: arch/arm/configs/marzen_defconfig
F: arch/arm/configs/shmobile_defconfig
F: arch/arm/include/debug/renesas-scif.S
diff --git a/arch/arm/configs/kzm9g_defconfig b/arch/arm/configs/kzm9g_defconfig
deleted file mode 100644
index 23e8d146dc16972f..0000000000000000
--- a/arch/arm/configs/kzm9g_defconfig
+++ /dev/null
@@ -1,154 +0,0 @@
-# CONFIG_ARM_PATCH_PHYS_VIRT is not set
-CONFIG_EXPERIMENTAL=y
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT\x16
-CONFIG_NAMESPACES=y
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_NET_NS is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_EMBEDDED=y
-CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_SH73A0=y
-CONFIG_MACH_KZM9G=y
-CONFIG_MEMORY_START=0x41000000
-CONFIG_MEMORY_SIZE=0x1f000000
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_SMP=y
-CONFIG_SCHED_MC=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_SH_IRDA=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_SMSC911X=y
-# CONFIG_WLAN is not set
-CONFIG_INPUT_SPARSEKMAP=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ST1232=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_ADXL34X=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=9
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_SH_MOBILE=y
-CONFIG_GPIO_PCF857X=y
-# CONFIG_HWMON is not set
-CONFIG_MFD_AS3711=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_AS3711=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_BACKLIGHT_AS3711=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_FB_SH_MOBILE_MERAM=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-# CONFIG_SND_USB is not set
-CONFIG_SND_SOC=y
-CONFIG_SND_SOC_SH4_FSI=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_R8A66597_HCD=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_USB_ETH=m
-CONFIG_USB_MASS_STORAGE=m
-CONFIG_MMC=y
-# CONFIG_MMC_BLOCK_BOUNCE is not set
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_RS5C372=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_ASYNC_TX_DMA=y
-CONFIG_STAGING=y
-CONFIG_IIO=y
-CONFIG_AK8975=y
-# CONFIG_DNOTIFY is not set
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_FTRACE is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRC16=y
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 02/15] ARM: shmobile: Remove legacy kzm9g_defconfig
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for KZM-A9-GT has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
MAINTAINERS | 1 -
arch/arm/configs/kzm9g_defconfig | 154 ---------------------------------------
2 files changed, 155 deletions(-)
delete mode 100644 arch/arm/configs/kzm9g_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index eaadc4a87d38bf64..f1fe0cc0dadee9df 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1457,7 +1457,6 @@ F: arch/arm/boot/dts/r8a*
F: arch/arm/boot/dts/sh*
F: arch/arm/configs/armadillo800eva_defconfig
F: arch/arm/configs/bockw_defconfig
-F: arch/arm/configs/kzm9g_defconfig
F: arch/arm/configs/marzen_defconfig
F: arch/arm/configs/shmobile_defconfig
F: arch/arm/include/debug/renesas-scif.S
diff --git a/arch/arm/configs/kzm9g_defconfig b/arch/arm/configs/kzm9g_defconfig
deleted file mode 100644
index 23e8d146dc16972f..0000000000000000
--- a/arch/arm/configs/kzm9g_defconfig
+++ /dev/null
@@ -1,154 +0,0 @@
-# CONFIG_ARM_PATCH_PHYS_VIRT is not set
-CONFIG_EXPERIMENTAL=y
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=16
-CONFIG_NAMESPACES=y
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_NET_NS is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_EMBEDDED=y
-CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_SH73A0=y
-CONFIG_MACH_KZM9G=y
-CONFIG_MEMORY_START=0x41000000
-CONFIG_MEMORY_SIZE=0x1f000000
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_SMP=y
-CONFIG_SCHED_MC=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_SH_IRDA=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_SMSC911X=y
-# CONFIG_WLAN is not set
-CONFIG_INPUT_SPARSEKMAP=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ST1232=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_ADXL34X=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=9
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_SH_MOBILE=y
-CONFIG_GPIO_PCF857X=y
-# CONFIG_HWMON is not set
-CONFIG_MFD_AS3711=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_AS3711=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_BACKLIGHT_AS3711=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_FB_SH_MOBILE_MERAM=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-# CONFIG_SND_USB is not set
-CONFIG_SND_SOC=y
-CONFIG_SND_SOC_SH4_FSI=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_R8A66597_HCD=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_USB_ETH=m
-CONFIG_USB_MASS_STORAGE=m
-CONFIG_MMC=y
-# CONFIG_MMC_BLOCK_BOUNCE is not set
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_RS5C372=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_ASYNC_TX_DMA=y
-CONFIG_STAGING=y
-CONFIG_IIO=y
-CONFIG_AK8975=y
-# CONFIG_DNOTIFY is not set
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_FTRACE is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRC16=y
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 03/15] ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for KZM-A9-GT has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/boot/dts/Makefile | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 679d7cc2f57c4981..e9eed01d48c5ccb5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -504,8 +504,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
r8a7740-armadillo800eva.dtb \
r8a7778-bockw.dtb \
r8a7778-bockw-reference.dtb \
- r8a7779-marzen.dtb \
- sh73a0-kzm9g.dtb
+ r8a7779-marzen.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
emev2-kzm9d.dtb \
r7s72100-genmai.dtb \
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 03/15] ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for KZM-A9-GT has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/boot/dts/Makefile | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 679d7cc2f57c4981..e9eed01d48c5ccb5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -504,8 +504,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
r8a7740-armadillo800eva.dtb \
r8a7778-bockw.dtb \
r8a7778-bockw-reference.dtb \
- r8a7779-marzen.dtb \
- sh73a0-kzm9g.dtb
+ r8a7779-marzen.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
emev2-kzm9d.dtb \
r7s72100-genmai.dtb \
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 04/15] ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the SH-Mobile AG5 (sh73a0) legacy SoC code was the
KZM-A9-GT legacy board code, which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 9 -
arch/arm/mach-shmobile/Makefile | 3 +-
arch/arm/mach-shmobile/clock-sh73a0.c | 752 ----------------------------------
arch/arm/mach-shmobile/pm-sh73a0.c | 32 --
arch/arm/mach-shmobile/setup-sh73a0.c | 739 +--------------------------------
arch/arm/mach-shmobile/sh73a0.h | 83 ----
arch/arm/mach-shmobile/smp-sh73a0.c | 8 -
7 files changed, 2 insertions(+), 1624 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/clock-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/pm-sh73a0.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 2a4d8348b6299dff..bc8e2f60fe505ee2 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -108,15 +108,6 @@ if ARCH_SHMOBILE_LEGACY
comment "Renesas ARM SoCs System Type"
-config ARCH_SH73A0
- bool "SH-Mobile AG5 (R8A73A00)"
- select ARCH_RMOBILE
- select ARCH_WANT_OPTIONAL_GPIOLIB
- select ARM_GIC
- select I2C
- select SH_INTC
- select RENESAS_INTC_IRQPIN
-
config ARCH_R8A7740
bool "R-Mobile A1 (R8A77400)"
select ARCH_RMOBILE
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 9bdb8a11acb10c4e..7e20ab3021be0ff2 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -6,7 +6,7 @@
obj-y := timer.o console.o
# CPU objects
-obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o pm-sh73a0.o
+obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o
obj-$(CONFIG_ARCH_R8A73A4) += setup-r8a73a4.o
obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o pm-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += setup-r8a7778.o
@@ -21,7 +21,6 @@ obj-$(CONFIG_ARCH_R7S72100) += setup-r7s72100.o
# Clock objects
ifndef CONFIG_COMMON_CLK
obj-y += clock.o
-obj-$(CONFIG_ARCH_SH73A0) += clock-sh73a0.o
obj-$(CONFIG_ARCH_R8A7740) += clock-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += clock-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += clock-r8a7779.o
diff --git a/arch/arm/mach-shmobile/clock-sh73a0.c b/arch/arm/mach-shmobile/clock-sh73a0.c
deleted file mode 100644
index 3855fb024fdbb1ca..0000000000000000
--- a/arch/arm/mach-shmobile/clock-sh73a0.c
+++ /dev/null
@@ -1,752 +0,0 @@
-/*
- * sh73a0 clock framework support
- *
- * Copyright (C) 2010 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/sh_clk.h>
-#include <linux/clkdev.h>
-#include <asm/processor.h>
-#include "clock.h"
-#include "common.h"
-
-#define FRQCRA IOMEM(0xe6150000)
-#define FRQCRB IOMEM(0xe6150004)
-#define FRQCRD IOMEM(0xe61500e4)
-#define VCLKCR1 IOMEM(0xe6150008)
-#define VCLKCR2 IOMEM(0xe615000C)
-#define VCLKCR3 IOMEM(0xe615001C)
-#define ZBCKCR IOMEM(0xe6150010)
-#define FLCKCR IOMEM(0xe6150014)
-#define SD0CKCR IOMEM(0xe6150074)
-#define SD1CKCR IOMEM(0xe6150078)
-#define SD2CKCR IOMEM(0xe615007C)
-#define FSIACKCR IOMEM(0xe6150018)
-#define FSIBCKCR IOMEM(0xe6150090)
-#define SUBCKCR IOMEM(0xe6150080)
-#define SPUACKCR IOMEM(0xe6150084)
-#define SPUVCKCR IOMEM(0xe6150094)
-#define MSUCKCR IOMEM(0xe6150088)
-#define HSICKCR IOMEM(0xe615008C)
-#define MFCK1CR IOMEM(0xe6150098)
-#define MFCK2CR IOMEM(0xe615009C)
-#define DSITCKCR IOMEM(0xe6150060)
-#define DSI0PCKCR IOMEM(0xe6150064)
-#define DSI1PCKCR IOMEM(0xe6150068)
-#define DSI0PHYCR 0xe615006C
-#define DSI1PHYCR 0xe6150070
-#define PLLECR IOMEM(0xe61500d0)
-#define PLL0CR IOMEM(0xe61500d8)
-#define PLL1CR IOMEM(0xe6150028)
-#define PLL2CR IOMEM(0xe615002c)
-#define PLL3CR IOMEM(0xe61500dc)
-#define SMSTPCR0 IOMEM(0xe6150130)
-#define SMSTPCR1 IOMEM(0xe6150134)
-#define SMSTPCR2 IOMEM(0xe6150138)
-#define SMSTPCR3 IOMEM(0xe615013c)
-#define SMSTPCR4 IOMEM(0xe6150140)
-#define SMSTPCR5 IOMEM(0xe6150144)
-#define CKSCR IOMEM(0xe61500c0)
-
-/* Fixed 32 KHz root clock from EXTALR pin */
-static struct clk r_clk = {
- .rate = 32768,
-};
-
-/*
- * 26MHz default rate for the EXTAL1 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-struct clk sh73a0_extal1_clk = {
- .rate = 26000000,
-};
-
-/*
- * 48MHz default rate for the EXTAL2 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-struct clk sh73a0_extal2_clk = {
- .rate = 48000000,
-};
-
-static struct sh_clk_ops main_clk_ops = {
- .recalc = followparent_recalc,
-};
-
-/* Main clock */
-static struct clk main_clk = {
- /* .parent wll be set on sh73a0_clock_init() */
- .ops = &main_clk_ops,
-};
-
-/* PLL0, PLL1, PLL2, PLL3 */
-static unsigned long pll_recalc(struct clk *clk)
-{
- unsigned long mult = 1;
-
- if (__raw_readl(PLLECR) & (1 << clk->enable_bit)) {
- mult = (((__raw_readl(clk->enable_reg) >> 24) & 0x3f) + 1);
- /* handle CFG bit for PLL1 and PLL2 */
- switch (clk->enable_bit) {
- case 1:
- case 2:
- if (__raw_readl(clk->enable_reg) & (1 << 20))
- mult *= 2;
- }
- }
-
- return clk->parent->rate * mult;
-}
-
-static struct sh_clk_ops pll_clk_ops = {
- .recalc = pll_recalc,
-};
-
-static struct clk pll0_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL0CR,
- .enable_bit = 0,
-};
-
-static struct clk pll1_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL1CR,
- .enable_bit = 1,
-};
-
-static struct clk pll2_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL2CR,
- .enable_bit = 2,
-};
-
-static struct clk pll3_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL3CR,
- .enable_bit = 3,
-};
-
-/* A fixed divide block */
-SH_CLK_RATIO(div2, 1, 2);
-SH_CLK_RATIO(div7, 1, 7);
-SH_CLK_RATIO(div13, 1, 13);
-
-SH_FIXED_RATIO_CLK(extal1_div2_clk, sh73a0_extal1_clk, div2);
-SH_FIXED_RATIO_CLK(extal2_div2_clk, sh73a0_extal2_clk, div2);
-SH_FIXED_RATIO_CLK(main_div2_clk, main_clk, div2);
-SH_FIXED_RATIO_CLK(pll1_div2_clk, pll1_clk, div2);
-SH_FIXED_RATIO_CLK(pll1_div7_clk, pll1_clk, div7);
-SH_FIXED_RATIO_CLK(pll1_div13_clk, pll1_clk, div13);
-
-/* External input clock */
-struct clk sh73a0_extcki_clk = {
-};
-
-struct clk sh73a0_extalr_clk = {
-};
-
-static struct clk *main_clks[] = {
- &r_clk,
- &sh73a0_extal1_clk,
- &sh73a0_extal2_clk,
- &extal1_div2_clk,
- &extal2_div2_clk,
- &main_clk,
- &main_div2_clk,
- &pll0_clk,
- &pll1_clk,
- &pll2_clk,
- &pll3_clk,
- &pll1_div2_clk,
- &pll1_div7_clk,
- &pll1_div13_clk,
- &sh73a0_extcki_clk,
- &sh73a0_extalr_clk,
-};
-
-static int frqcr_kick(void)
-{
- int i;
-
- /* set KICK bit in FRQCRB to update hardware setting, check success */
- __raw_writel(__raw_readl(FRQCRB) | (1 << 31), FRQCRB);
- for (i = 1000; i; i--)
- if (__raw_readl(FRQCRB) & (1 << 31))
- cpu_relax();
- else
- return i;
-
- return -ETIMEDOUT;
-}
-
-static void div4_kick(struct clk *clk)
-{
- frqcr_kick();
-}
-
-static int divisors[] = { 2, 3, 4, 6, 8, 12, 16, 18,
- 24, 0, 36, 48, 7 };
-
-static struct clk_div_mult_table div4_div_mult_table = {
- .divisors = divisors,
- .nr_divisors = ARRAY_SIZE(divisors),
-};
-
-static struct clk_div4_table div4_table = {
- .div_mult_table = &div4_div_mult_table,
- .kick = div4_kick,
-};
-
-enum { DIV4_I, DIV4_ZG, DIV4_M3, DIV4_B, DIV4_M1, DIV4_M2,
- DIV4_Z, DIV4_ZX, DIV4_HP, DIV4_NR };
-
-#define DIV4(_reg, _bit, _mask, _flags) \
- SH_CLK_DIV4(&pll1_clk, _reg, _bit, _mask, _flags)
-
-static struct clk div4_clks[DIV4_NR] = {
- [DIV4_I] = DIV4(FRQCRA, 20, 0xdff, CLK_ENABLE_ON_INIT),
- /*
- * ZG clock is dividing PLL0 frequency to supply SGX. Make sure not to
- * exceed maximum frequencies of 201.5MHz for VDD_DVFS=1.175 and
- * 239.2MHz for VDD_DVFS=1.315V.
- */
- [DIV4_ZG] = SH_CLK_DIV4(&pll0_clk, FRQCRA, 16, 0xd7f, CLK_ENABLE_ON_INIT),
- [DIV4_M3] = DIV4(FRQCRA, 12, 0x1dff, CLK_ENABLE_ON_INIT),
- [DIV4_B] = DIV4(FRQCRA, 8, 0xdff, CLK_ENABLE_ON_INIT),
- [DIV4_M1] = DIV4(FRQCRA, 4, 0x1dff, 0),
- [DIV4_M2] = DIV4(FRQCRA, 0, 0x1dff, 0),
- [DIV4_Z] = SH_CLK_DIV4(&pll0_clk, FRQCRB, 24, 0x97f, 0),
- [DIV4_ZX] = DIV4(FRQCRB, 12, 0xdff, 0),
- [DIV4_HP] = DIV4(FRQCRB, 4, 0xdff, 0),
-};
-
-static unsigned long twd_recalc(struct clk *clk)
-{
- return clk_get_rate(clk->parent) / 4;
-}
-
-static struct sh_clk_ops twd_clk_ops = {
- .recalc = twd_recalc,
-};
-
-static struct clk twd_clk = {
- .parent = &div4_clks[DIV4_Z],
- .ops = &twd_clk_ops,
-};
-
-static struct sh_clk_ops zclk_ops, kicker_ops;
-static const struct sh_clk_ops *div4_clk_ops;
-
-static int zclk_set_rate(struct clk *clk, unsigned long rate)
-{
- int ret;
-
- if (!clk->parent || !__clk_get(clk->parent))
- return -ENODEV;
-
- if (readl(FRQCRB) & (1 << 31))
- return -EBUSY;
-
- if (rate = clk_get_rate(clk->parent)) {
- /* 1:1 - switch off divider */
- __raw_writel(__raw_readl(FRQCRB) & ~(1 << 28), FRQCRB);
- /* nullify the divider to prepare for the next time */
- ret = div4_clk_ops->set_rate(clk, rate / 2);
- if (!ret)
- ret = frqcr_kick();
- if (ret > 0)
- ret = 0;
- } else {
- /* Enable the divider */
- __raw_writel(__raw_readl(FRQCRB) | (1 << 28), FRQCRB);
-
- ret = frqcr_kick();
- if (ret >= 0)
- /*
- * set the divider - call the DIV4 method, it will kick
- * FRQCRB too
- */
- ret = div4_clk_ops->set_rate(clk, rate);
- if (ret < 0)
- goto esetrate;
- }
-
-esetrate:
- __clk_put(clk->parent);
- return ret;
-}
-
-static long zclk_round_rate(struct clk *clk, unsigned long rate)
-{
- unsigned long div_freq = div4_clk_ops->round_rate(clk, rate),
- parent_freq = clk_get_rate(clk->parent);
-
- if (rate > div_freq && abs(parent_freq - rate) < rate - div_freq)
- return parent_freq;
-
- return div_freq;
-}
-
-static unsigned long zclk_recalc(struct clk *clk)
-{
- /*
- * Must recalculate frequencies in case PLL0 has been changed, even if
- * the divisor is unused ATM!
- */
- unsigned long div_freq = div4_clk_ops->recalc(clk);
-
- if (__raw_readl(FRQCRB) & (1 << 28))
- return div_freq;
-
- return clk_get_rate(clk->parent);
-}
-
-static int kicker_set_rate(struct clk *clk, unsigned long rate)
-{
- if (__raw_readl(FRQCRB) & (1 << 31))
- return -EBUSY;
-
- return div4_clk_ops->set_rate(clk, rate);
-}
-
-static void div4_clk_extend(void)
-{
- int i;
-
- div4_clk_ops = div4_clks[0].ops;
-
- /* Add a kicker-busy check before changing the rate */
- kicker_ops = *div4_clk_ops;
- /* We extend the DIV4 clock with a 1:1 pass-through case */
- zclk_ops = *div4_clk_ops;
-
- kicker_ops.set_rate = kicker_set_rate;
- zclk_ops.set_rate = zclk_set_rate;
- zclk_ops.round_rate = zclk_round_rate;
- zclk_ops.recalc = zclk_recalc;
-
- for (i = 0; i < DIV4_NR; i++)
- div4_clks[i].ops = i = DIV4_Z ? &zclk_ops : &kicker_ops;
-}
-
-enum { DIV6_VCK1, DIV6_VCK2, DIV6_VCK3, DIV6_ZB1,
- DIV6_FLCTL, DIV6_SDHI0, DIV6_SDHI1, DIV6_SDHI2,
- DIV6_FSIA, DIV6_FSIB, DIV6_SUB,
- DIV6_SPUA, DIV6_SPUV, DIV6_MSU,
- DIV6_HSI, DIV6_MFG1, DIV6_MFG2,
- DIV6_DSIT, DIV6_DSI0P, DIV6_DSI1P,
- DIV6_NR };
-
-static struct clk *vck_parent[8] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &sh73a0_extcki_clk,
- [3] = &sh73a0_extal2_clk,
- [4] = &main_div2_clk,
- [5] = &sh73a0_extalr_clk,
- [6] = &main_clk,
-};
-
-static struct clk *pll_parent[4] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &pll1_div13_clk,
-};
-
-static struct clk *hsi_parent[4] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &pll1_div7_clk,
-};
-
-static struct clk *pll_extal2_parent[] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &sh73a0_extal2_clk,
- [3] = &sh73a0_extal2_clk,
-};
-
-static struct clk *dsi_parent[8] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &main_clk,
- [3] = &sh73a0_extal2_clk,
- [4] = &sh73a0_extcki_clk,
-};
-
-static struct clk div6_clks[DIV6_NR] = {
- [DIV6_VCK1] = SH_CLK_DIV6_EXT(VCLKCR1, 0,
- vck_parent, ARRAY_SIZE(vck_parent), 12, 3),
- [DIV6_VCK2] = SH_CLK_DIV6_EXT(VCLKCR2, 0,
- vck_parent, ARRAY_SIZE(vck_parent), 12, 3),
- [DIV6_VCK3] = SH_CLK_DIV6_EXT(VCLKCR3, 0,
- vck_parent, ARRAY_SIZE(vck_parent), 12, 3),
- [DIV6_ZB1] = SH_CLK_DIV6_EXT(ZBCKCR, CLK_ENABLE_ON_INIT,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_FLCTL] = SH_CLK_DIV6_EXT(FLCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_SDHI0] = SH_CLK_DIV6_EXT(SD0CKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 2),
- [DIV6_SDHI1] = SH_CLK_DIV6_EXT(SD1CKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 2),
- [DIV6_SDHI2] = SH_CLK_DIV6_EXT(SD2CKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 2),
- [DIV6_FSIA] = SH_CLK_DIV6_EXT(FSIACKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 1),
- [DIV6_FSIB] = SH_CLK_DIV6_EXT(FSIBCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 1),
- [DIV6_SUB] = SH_CLK_DIV6_EXT(SUBCKCR, 0,
- pll_extal2_parent, ARRAY_SIZE(pll_extal2_parent), 6, 2),
- [DIV6_SPUA] = SH_CLK_DIV6_EXT(SPUACKCR, 0,
- pll_extal2_parent, ARRAY_SIZE(pll_extal2_parent), 6, 2),
- [DIV6_SPUV] = SH_CLK_DIV6_EXT(SPUVCKCR, 0,
- pll_extal2_parent, ARRAY_SIZE(pll_extal2_parent), 6, 2),
- [DIV6_MSU] = SH_CLK_DIV6_EXT(MSUCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_HSI] = SH_CLK_DIV6_EXT(HSICKCR, 0,
- hsi_parent, ARRAY_SIZE(hsi_parent), 6, 2),
- [DIV6_MFG1] = SH_CLK_DIV6_EXT(MFCK1CR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_MFG2] = SH_CLK_DIV6_EXT(MFCK2CR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_DSIT] = SH_CLK_DIV6_EXT(DSITCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_DSI0P] = SH_CLK_DIV6_EXT(DSI0PCKCR, 0,
- dsi_parent, ARRAY_SIZE(dsi_parent), 12, 3),
- [DIV6_DSI1P] = SH_CLK_DIV6_EXT(DSI1PCKCR, 0,
- dsi_parent, ARRAY_SIZE(dsi_parent), 12, 3),
-};
-
-/* DSI DIV */
-static unsigned long dsiphy_recalc(struct clk *clk)
-{
- u32 value;
-
- value = __raw_readl(clk->mapping->base);
-
- /* FIXME */
- if (!(value & 0x000B8000))
- return clk->parent->rate;
-
- value &= 0x3f;
- value += 1;
-
- if ((value < 12) ||
- (value > 33)) {
- pr_err("DSIPHY has wrong value (%d)", value);
- return 0;
- }
-
- return clk->parent->rate / value;
-}
-
-static long dsiphy_round_rate(struct clk *clk, unsigned long rate)
-{
- return clk_rate_mult_range_round(clk, 12, 33, rate);
-}
-
-static void dsiphy_disable(struct clk *clk)
-{
- u32 value;
-
- value = __raw_readl(clk->mapping->base);
- value &= ~0x000B8000;
-
- __raw_writel(value , clk->mapping->base);
-}
-
-static int dsiphy_enable(struct clk *clk)
-{
- u32 value;
- int multi;
-
- value = __raw_readl(clk->mapping->base);
- multi = (value & 0x3f) + 1;
-
- if ((multi < 12) || (multi > 33))
- return -EIO;
-
- __raw_writel(value | 0x000B8000, clk->mapping->base);
-
- return 0;
-}
-
-static int dsiphy_set_rate(struct clk *clk, unsigned long rate)
-{
- u32 value;
- int idx;
-
- idx = rate / clk->parent->rate;
- if ((idx < 12) || (idx > 33))
- return -EINVAL;
-
- idx += -1;
-
- value = __raw_readl(clk->mapping->base);
- value = (value & ~0x3f) + idx;
-
- __raw_writel(value, clk->mapping->base);
-
- return 0;
-}
-
-static struct sh_clk_ops dsiphy_clk_ops = {
- .recalc = dsiphy_recalc,
- .round_rate = dsiphy_round_rate,
- .set_rate = dsiphy_set_rate,
- .enable = dsiphy_enable,
- .disable = dsiphy_disable,
-};
-
-static struct clk_mapping dsi0phy_clk_mapping = {
- .phys = DSI0PHYCR,
- .len = 4,
-};
-
-static struct clk_mapping dsi1phy_clk_mapping = {
- .phys = DSI1PHYCR,
- .len = 4,
-};
-
-static struct clk dsi0phy_clk = {
- .ops = &dsiphy_clk_ops,
- .parent = &div6_clks[DIV6_DSI0P], /* late install */
- .mapping = &dsi0phy_clk_mapping,
-};
-
-static struct clk dsi1phy_clk = {
- .ops = &dsiphy_clk_ops,
- .parent = &div6_clks[DIV6_DSI1P], /* late install */
- .mapping = &dsi1phy_clk_mapping,
-};
-
-static struct clk *late_main_clks[] = {
- &dsi0phy_clk,
- &dsi1phy_clk,
- &twd_clk,
-};
-
-enum { MSTP001,
- MSTP129, MSTP128, MSTP127, MSTP126, MSTP125, MSTP118, MSTP116, MSTP112, MSTP100,
- MSTP219, MSTP218, MSTP217,
- MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
- MSTP331, MSTP329, MSTP328, MSTP325, MSTP323, MSTP322,
- MSTP314, MSTP313, MSTP312, MSTP311,
- MSTP304, MSTP303, MSTP302, MSTP301, MSTP300,
- MSTP411, MSTP410, MSTP403,
- MSTP508,
- MSTP_NR };
-
-#define MSTP(_parent, _reg, _bit, _flags) \
- SH_CLK_MSTP32(_parent, _reg, _bit, _flags)
-
-static struct clk mstp_clks[MSTP_NR] = {
- [MSTP001] = MSTP(&div4_clks[DIV4_HP], SMSTPCR0, 1, 0), /* IIC2 */
- [MSTP129] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 29, 0), /* CEU1 */
- [MSTP128] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 28, 0), /* CSI2-RX1 */
- [MSTP127] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 27, 0), /* CEU0 */
- [MSTP126] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 26, 0), /* CSI2-RX0 */
- [MSTP125] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR1, 25, 0), /* TMU0 */
- [MSTP118] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 18, 0), /* DSITX0 */
- [MSTP116] = MSTP(&div4_clks[DIV4_HP], SMSTPCR1, 16, 0), /* IIC0 */
- [MSTP112] = MSTP(&div4_clks[DIV4_ZG], SMSTPCR1, 12, 0), /* SGX */
- [MSTP100] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 0, 0), /* LCDC0 */
- [MSTP219] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 19, 0), /* SCIFA7 */
- [MSTP218] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* SY-DMAC */
- [MSTP217] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 17, 0), /* MP-DMAC */
- [MSTP207] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */
- [MSTP206] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */
- [MSTP204] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */
- [MSTP203] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 3, 0), /* SCIFA1 */
- [MSTP202] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 2, 0), /* SCIFA2 */
- [MSTP201] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 1, 0), /* SCIFA3 */
- [MSTP200] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 0, 0), /* SCIFA4 */
- [MSTP331] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 31, 0), /* SCIFA6 */
- [MSTP329] = MSTP(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */
- [MSTP328] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 28, 0), /*FSI*/
- [MSTP325] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 25, 0), /* IrDA */
- [MSTP323] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 23, 0), /* IIC1 */
- [MSTP322] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 22, 0), /* USB */
- [MSTP314] = MSTP(&div6_clks[DIV6_SDHI0], SMSTPCR3, 14, 0), /* SDHI0 */
- [MSTP313] = MSTP(&div6_clks[DIV6_SDHI1], SMSTPCR3, 13, 0), /* SDHI1 */
- [MSTP312] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 12, 0), /* MMCIF0 */
- [MSTP311] = MSTP(&div6_clks[DIV6_SDHI2], SMSTPCR3, 11, 0), /* SDHI2 */
- [MSTP304] = MSTP(&main_div2_clk, SMSTPCR3, 4, 0), /* TPU0 */
- [MSTP303] = MSTP(&main_div2_clk, SMSTPCR3, 3, 0), /* TPU1 */
- [MSTP302] = MSTP(&main_div2_clk, SMSTPCR3, 2, 0), /* TPU2 */
- [MSTP301] = MSTP(&main_div2_clk, SMSTPCR3, 1, 0), /* TPU3 */
- [MSTP300] = MSTP(&main_div2_clk, SMSTPCR3, 0, 0), /* TPU4 */
- [MSTP411] = MSTP(&div4_clks[DIV4_HP], SMSTPCR4, 11, 0), /* IIC3 */
- [MSTP410] = MSTP(&div4_clks[DIV4_HP], SMSTPCR4, 10, 0), /* IIC4 */
- [MSTP403] = MSTP(&r_clk, SMSTPCR4, 3, 0), /* KEYSC */
- [MSTP508] = MSTP(&div4_clks[DIV4_HP], SMSTPCR5, 8, 0), /* INTCA0 */
-};
-
-/* The lookups structure below includes duplicate entries for some clocks
- * with alternate names.
- * - The traditional name used when a device is initialised with platform data
- * - The name used when a device is initialised using device tree
- * The longer-term aim is to remove these duplicates, and indeed the
- * lookups table entirely, by describing clocks using device tree.
- */
-static struct clk_lookup lookups[] = {
- /* main clocks */
- CLKDEV_CON_ID("r_clk", &r_clk),
- CLKDEV_DEV_ID("smp_twd", &twd_clk), /* smp_twd */
-
- /* DIV4 clocks */
- CLKDEV_DEV_ID("cpu0", &div4_clks[DIV4_Z]),
-
- /* DIV6 clocks */
- CLKDEV_CON_ID("vck1_clk", &div6_clks[DIV6_VCK1]),
- CLKDEV_CON_ID("vck2_clk", &div6_clks[DIV6_VCK2]),
- CLKDEV_CON_ID("vck3_clk", &div6_clks[DIV6_VCK3]),
- CLKDEV_CON_ID("sdhi0_clk", &div6_clks[DIV6_SDHI0]),
- CLKDEV_CON_ID("sdhi1_clk", &div6_clks[DIV6_SDHI1]),
- CLKDEV_CON_ID("sdhi2_clk", &div6_clks[DIV6_SDHI2]),
-
- /* MSTP32 clocks */
- CLKDEV_DEV_ID("i2c-sh_mobile.2", &mstp_clks[MSTP001]), /* I2C2 */
- CLKDEV_DEV_ID("e6824000.i2c", &mstp_clks[MSTP001]), /* I2C2 */
- CLKDEV_DEV_ID("sh_mobile_ceu.1", &mstp_clks[MSTP129]), /* CEU1 */
- CLKDEV_DEV_ID("sh-mobile-csi2.1", &mstp_clks[MSTP128]), /* CSI2-RX1 */
- CLKDEV_DEV_ID("sh_mobile_ceu.0", &mstp_clks[MSTP127]), /* CEU0 */
- CLKDEV_DEV_ID("sh-mobile-csi2.0", &mstp_clks[MSTP126]), /* CSI2-RX0 */
- CLKDEV_DEV_ID("sh-mipi-dsi.0", &mstp_clks[MSTP118]), /* DSITX */
- CLKDEV_DEV_ID("i2c-sh_mobile.0", &mstp_clks[MSTP116]), /* I2C0 */
- CLKDEV_DEV_ID("e6820000.i2c", &mstp_clks[MSTP116]), /* I2C0 */
- CLKDEV_DEV_ID("sh_mobile_lcdc_fb.0", &mstp_clks[MSTP100]), /* LCDC0 */
- CLKDEV_DEV_ID("sh-sci.7", &mstp_clks[MSTP219]), /* SCIFA7 */
- CLKDEV_DEV_ID("e6cd0000.serial", &mstp_clks[MSTP219]), /* SCIFA7 */
- CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]), /* SY-DMAC */
- CLKDEV_DEV_ID("sh-dma-engine.1", &mstp_clks[MSTP217]), /* MP-DMAC */
- CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
- CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]), /* SCIFA5 */
- CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]), /* SCIFB */
- CLKDEV_DEV_ID("e6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
- CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
- CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]), /* SCIFA0 */
- CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */
- CLKDEV_DEV_ID("e6c50000.serial", &mstp_clks[MSTP203]), /* SCIFA1 */
- CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP202]), /* SCIFA2 */
- CLKDEV_DEV_ID("e6c60000.serial", &mstp_clks[MSTP202]), /* SCIFA2 */
- CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP201]), /* SCIFA3 */
- CLKDEV_DEV_ID("e6c70000.serial", &mstp_clks[MSTP201]), /* SCIFA3 */
- CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP200]), /* SCIFA4 */
- CLKDEV_DEV_ID("e6c80000.serial", &mstp_clks[MSTP200]), /* SCIFA4 */
- CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP331]), /* SCIFA6 */
- CLKDEV_DEV_ID("e6cc0000.serial", &mstp_clks[MSTP331]), /* SCIFA6 */
- CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]), /* FSI */
- CLKDEV_DEV_ID("ec230000.sound", &mstp_clks[MSTP328]), /* FSI */
- CLKDEV_DEV_ID("sh_irda.0", &mstp_clks[MSTP325]), /* IrDA */
- CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]), /* I2C1 */
- CLKDEV_DEV_ID("e6822000.i2c", &mstp_clks[MSTP323]), /* I2C1 */
- CLKDEV_DEV_ID("renesas_usbhs", &mstp_clks[MSTP322]), /* USB */
- CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP314]), /* SDHI0 */
- CLKDEV_DEV_ID("ee100000.sd", &mstp_clks[MSTP314]), /* SDHI0 */
- CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP313]), /* SDHI1 */
- CLKDEV_DEV_ID("ee120000.sd", &mstp_clks[MSTP313]), /* SDHI1 */
- CLKDEV_DEV_ID("sh_mmcif.0", &mstp_clks[MSTP312]), /* MMCIF0 */
- CLKDEV_DEV_ID("e6bd0000.mmc", &mstp_clks[MSTP312]), /* MMCIF0 */
- CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP311]), /* SDHI2 */
- CLKDEV_DEV_ID("ee140000.sd", &mstp_clks[MSTP311]), /* SDHI2 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.0", &mstp_clks[MSTP304]), /* TPU0 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.1", &mstp_clks[MSTP303]), /* TPU1 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.2", &mstp_clks[MSTP302]), /* TPU2 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.3", &mstp_clks[MSTP301]), /* TPU3 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.4", &mstp_clks[MSTP300]), /* TPU4 */
- CLKDEV_DEV_ID("i2c-sh_mobile.3", &mstp_clks[MSTP411]), /* I2C3 */
- CLKDEV_DEV_ID("e6826000.i2c", &mstp_clks[MSTP411]), /* I2C3 */
- CLKDEV_DEV_ID("i2c-sh_mobile.4", &mstp_clks[MSTP410]), /* I2C4 */
- CLKDEV_DEV_ID("e6828000.i2c", &mstp_clks[MSTP410]), /* I2C4 */
- CLKDEV_DEV_ID("sh_keysc.0", &mstp_clks[MSTP403]), /* KEYSC */
- CLKDEV_DEV_ID("renesas_intc_irqpin.0", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e6900000.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("renesas_intc_irqpin.1", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e6900004.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("renesas_intc_irqpin.2", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e6900008.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("renesas_intc_irqpin.3", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e690000c.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
-
- /* ICK */
- CLKDEV_ICK_ID("dsit_clk", "sh-mipi-dsi.0", &div6_clks[DIV6_DSIT]),
- CLKDEV_ICK_ID("dsit_clk", "sh-mipi-dsi.1", &div6_clks[DIV6_DSIT]),
- CLKDEV_ICK_ID("dsip_clk", "sh-mipi-dsi.0", &div6_clks[DIV6_DSI0P]),
- CLKDEV_ICK_ID("dsip_clk", "sh-mipi-dsi.1", &div6_clks[DIV6_DSI1P]),
- CLKDEV_ICK_ID("dsiphy_clk", "sh-mipi-dsi.0", &dsi0phy_clk),
- CLKDEV_ICK_ID("dsiphy_clk", "sh-mipi-dsi.1", &dsi1phy_clk),
- CLKDEV_ICK_ID("fck", "sh-cmt-48.1", &mstp_clks[MSTP329]), /* CMT1 */
- CLKDEV_ICK_ID("fck", "e6138000.timer", &mstp_clks[MSTP329]), /* CMT1 */
- CLKDEV_ICK_ID("fck", "sh-tmu.0", &mstp_clks[MSTP125]), /* TMU0 */
-};
-
-void __init sh73a0_clock_init(void)
-{
- int k, ret = 0;
-
- /* Set SDHI clocks to a known state */
- __raw_writel(0x108, SD0CKCR);
- __raw_writel(0x108, SD1CKCR);
- __raw_writel(0x108, SD2CKCR);
-
- /* detect main clock parent */
- switch ((__raw_readl(CKSCR) >> 28) & 0x03) {
- case 0:
- main_clk.parent = &sh73a0_extal1_clk;
- break;
- case 1:
- main_clk.parent = &extal1_div2_clk;
- break;
- case 2:
- main_clk.parent = &sh73a0_extal2_clk;
- break;
- case 3:
- main_clk.parent = &extal2_div2_clk;
- break;
- }
-
- for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
- ret = clk_register(main_clks[k]);
-
- if (!ret) {
- ret = sh_clk_div4_register(div4_clks, DIV4_NR, &div4_table);
- if (!ret)
- div4_clk_extend();
- }
-
- if (!ret)
- ret = sh_clk_div6_reparent_register(div6_clks, DIV6_NR);
-
- if (!ret)
- ret = sh_clk_mstp_register(mstp_clks, MSTP_NR);
-
- for (k = 0; !ret && (k < ARRAY_SIZE(late_main_clks)); k++)
- ret = clk_register(late_main_clks[k]);
-
- clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-
- if (!ret)
- shmobile_clk_init();
- else
- panic("failed to setup sh73a0 clocks\n");
-}
diff --git a/arch/arm/mach-shmobile/pm-sh73a0.c b/arch/arm/mach-shmobile/pm-sh73a0.c
deleted file mode 100644
index a7e466817965e3b8..0000000000000000
--- a/arch/arm/mach-shmobile/pm-sh73a0.c
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * sh73a0 Power management support
- *
- * Copyright (C) 2012 Bastian Hecht <hechtb+renesas@gmail.com>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/suspend.h>
-#include "common.h"
-
-#ifdef CONFIG_SUSPEND
-static int sh73a0_enter_suspend(suspend_state_t suspend_state)
-{
- cpu_do_idle();
- return 0;
-}
-
-static void sh73a0_suspend_init(void)
-{
- shmobile_suspend_ops.enter = sh73a0_enter_suspend;
-}
-#else
-static void sh73a0_suspend_init(void) {}
-#endif
-
-void __init sh73a0_pm_init(void)
-{
- sh73a0_suspend_init();
-}
diff --git a/arch/arm/mach-shmobile/setup-sh73a0.c b/arch/arm/mach-shmobile/setup-sh73a0.c
index fb2ab7590af8bf9d..a1e8e72e25b58c3e 100644
--- a/arch/arm/mach-shmobile/setup-sh73a0.c
+++ b/arch/arm/mach-shmobile/setup-sh73a0.c
@@ -18,28 +18,17 @@
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <linux/platform_device.h>
#include <linux/of_platform.h>
#include <linux/delay.h>
#include <linux/input.h>
-#include <linux/i2c/i2c-sh_mobile.h>
#include <linux/io.h>
-#include <linux/serial_sci.h>
-#include <linux/sh_dma.h>
-#include <linux/sh_timer.h>
-#include <linux/platform_data/sh_ipmmu.h>
-#include <linux/platform_data/irq-renesas-intc-irqpin.h>
#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include "common.h"
-#include "dma-register.h"
-#include "intc.h"
-#include "irqs.h"
#include "sh73a0.h"
static struct map_desc sh73a0_io_desc[] __initdata = {
@@ -54,737 +43,12 @@ static struct map_desc sh73a0_io_desc[] __initdata = {
},
};
-void __init sh73a0_map_io(void)
+static void __init sh73a0_map_io(void)
{
debug_ll_io_init();
iotable_init(sh73a0_io_desc, ARRAY_SIZE(sh73a0_io_desc));
}
-/* PFC */
-static struct resource pfc_resources[] __initdata = {
- DEFINE_RES_MEM(0xe6050000, 0x8000),
- DEFINE_RES_MEM(0xe605801c, 0x000c),
-};
-
-void __init sh73a0_pinmux_init(void)
-{
- platform_device_register_simple("pfc-sh73a0", -1, pfc_resources,
- ARRAY_SIZE(pfc_resources));
-}
-
-/* SCIF */
-#define SH73A0_SCIF(scif_type, index, baseaddr, irq) \
-static struct plat_sci_port scif##index##_platform_data = { \
- .type = scif_type, \
- .flags = UPF_BOOT_AUTOCONF, \
- .scscr = SCSCR_RE | SCSCR_TE, \
-}; \
- \
-static struct resource scif##index##_resources[] = { \
- DEFINE_RES_MEM(baseaddr, 0x100), \
- DEFINE_RES_IRQ(irq), \
-}; \
- \
-static struct platform_device scif##index##_device = { \
- .name = "sh-sci", \
- .id = index, \
- .resource = scif##index##_resources, \
- .num_resources = ARRAY_SIZE(scif##index##_resources), \
- .dev = { \
- .platform_data = &scif##index##_platform_data, \
- }, \
-}
-
-SH73A0_SCIF(PORT_SCIFA, 0, 0xe6c40000, gic_spi(72));
-SH73A0_SCIF(PORT_SCIFA, 1, 0xe6c50000, gic_spi(73));
-SH73A0_SCIF(PORT_SCIFA, 2, 0xe6c60000, gic_spi(74));
-SH73A0_SCIF(PORT_SCIFA, 3, 0xe6c70000, gic_spi(75));
-SH73A0_SCIF(PORT_SCIFA, 4, 0xe6c80000, gic_spi(78));
-SH73A0_SCIF(PORT_SCIFA, 5, 0xe6cb0000, gic_spi(79));
-SH73A0_SCIF(PORT_SCIFA, 6, 0xe6cc0000, gic_spi(156));
-SH73A0_SCIF(PORT_SCIFA, 7, 0xe6cd0000, gic_spi(143));
-SH73A0_SCIF(PORT_SCIFB, 8, 0xe6c30000, gic_spi(80));
-
-static struct sh_timer_config cmt1_platform_data = {
- .channels_mask = 0x3f,
-};
-
-static struct resource cmt1_resources[] = {
- DEFINE_RES_MEM(0xe6138000, 0x200),
- DEFINE_RES_IRQ(gic_spi(65)),
-};
-
-static struct platform_device cmt1_device = {
- .name = "sh-cmt-48",
- .id = 1,
- .dev = {
- .platform_data = &cmt1_platform_data,
- },
- .resource = cmt1_resources,
- .num_resources = ARRAY_SIZE(cmt1_resources),
-};
-
-/* TMU */
-static struct sh_timer_config tmu0_platform_data = {
- .channels_mask = 7,
-};
-
-static struct resource tmu0_resources[] = {
- DEFINE_RES_MEM(0xfff60000, 0x2c),
- DEFINE_RES_IRQ(intcs_evt2irq(0xe80)),
- DEFINE_RES_IRQ(intcs_evt2irq(0xea0)),
- DEFINE_RES_IRQ(intcs_evt2irq(0xec0)),
-};
-
-static struct platform_device tmu0_device = {
- .name = "sh-tmu",
- .id = 0,
- .dev = {
- .platform_data = &tmu0_platform_data,
- },
- .resource = tmu0_resources,
- .num_resources = ARRAY_SIZE(tmu0_resources),
-};
-
-static struct resource i2c0_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6820000, 0x426),
- [1] = {
- .start = gic_spi(167),
- .end = gic_spi(170),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6822000, 0x426),
- [1] = {
- .start = gic_spi(51),
- .end = gic_spi(54),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c2_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6824000, 0x426),
- [1] = {
- .start = gic_spi(171),
- .end = gic_spi(174),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c3_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6826000, 0x426),
- [1] = {
- .start = gic_spi(183),
- .end = gic_spi(186),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c4_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6828000, 0x426),
- [1] = {
- .start = gic_spi(187),
- .end = gic_spi(190),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct i2c_sh_mobile_platform_data i2c_platform_data = {
- .clks_per_count = 2,
-};
-
-static struct platform_device i2c0_device = {
- .name = "i2c-sh_mobile",
- .id = 0,
- .resource = i2c0_resources,
- .num_resources = ARRAY_SIZE(i2c0_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c1_device = {
- .name = "i2c-sh_mobile",
- .id = 1,
- .resource = i2c1_resources,
- .num_resources = ARRAY_SIZE(i2c1_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c2_device = {
- .name = "i2c-sh_mobile",
- .id = 2,
- .resource = i2c2_resources,
- .num_resources = ARRAY_SIZE(i2c2_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c3_device = {
- .name = "i2c-sh_mobile",
- .id = 3,
- .resource = i2c3_resources,
- .num_resources = ARRAY_SIZE(i2c3_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c4_device = {
- .name = "i2c-sh_mobile",
- .id = 4,
- .resource = i2c4_resources,
- .num_resources = ARRAY_SIZE(i2c4_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static const struct sh_dmae_slave_config sh73a0_dmae_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_SCIF0_TX,
- .addr = 0xe6c40020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x21,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF0_RX,
- .addr = 0xe6c40024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x22,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF1_TX,
- .addr = 0xe6c50020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x25,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF1_RX,
- .addr = 0xe6c50024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x26,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF2_TX,
- .addr = 0xe6c60020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x29,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF2_RX,
- .addr = 0xe6c60024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x2a,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF3_TX,
- .addr = 0xe6c70020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x2d,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF3_RX,
- .addr = 0xe6c70024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x2e,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF4_TX,
- .addr = 0xe6c80020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x39,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF4_RX,
- .addr = 0xe6c80024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x3a,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF5_TX,
- .addr = 0xe6cb0020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x35,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF5_RX,
- .addr = 0xe6cb0024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x36,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF6_TX,
- .addr = 0xe6cc0020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x1d,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF6_RX,
- .addr = 0xe6cc0024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x1e,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF7_TX,
- .addr = 0xe6cd0020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x19,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF7_RX,
- .addr = 0xe6cd0024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x1a,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF8_TX,
- .addr = 0xe6c30040,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x3d,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF8_RX,
- .addr = 0xe6c30060,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x3e,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI0_TX,
- .addr = 0xee100030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc1,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI0_RX,
- .addr = 0xee100030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xc2,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_TX,
- .addr = 0xee120030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc9,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_RX,
- .addr = 0xee120030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xca,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_TX,
- .addr = 0xee140030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xcd,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_RX,
- .addr = 0xee140030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xce,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_TX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd1,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_RX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xd2,
- },
-};
-
-#define DMAE_CHANNEL(_offset) \
- { \
- .offset = _offset - 0x20, \
- .dmars = _offset - 0x20 + 0x40, \
- }
-
-static const struct sh_dmae_channel sh73a0_dmae_channels[] = {
- DMAE_CHANNEL(0x8000),
- DMAE_CHANNEL(0x8080),
- DMAE_CHANNEL(0x8100),
- DMAE_CHANNEL(0x8180),
- DMAE_CHANNEL(0x8200),
- DMAE_CHANNEL(0x8280),
- DMAE_CHANNEL(0x8300),
- DMAE_CHANNEL(0x8380),
- DMAE_CHANNEL(0x8400),
- DMAE_CHANNEL(0x8480),
- DMAE_CHANNEL(0x8500),
- DMAE_CHANNEL(0x8580),
- DMAE_CHANNEL(0x8600),
- DMAE_CHANNEL(0x8680),
- DMAE_CHANNEL(0x8700),
- DMAE_CHANNEL(0x8780),
- DMAE_CHANNEL(0x8800),
- DMAE_CHANNEL(0x8880),
- DMAE_CHANNEL(0x8900),
- DMAE_CHANNEL(0x8980),
-};
-
-static struct sh_dmae_pdata sh73a0_dmae_platform_data = {
- .slave = sh73a0_dmae_slaves,
- .slave_num = ARRAY_SIZE(sh73a0_dmae_slaves),
- .channel = sh73a0_dmae_channels,
- .channel_num = ARRAY_SIZE(sh73a0_dmae_channels),
- .ts_low_shift = TS_LOW_SHIFT,
- .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
- .ts_high_shift = TS_HI_SHIFT,
- .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
- .ts_shift = dma_ts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
- .dmaor_init = DMAOR_DME,
-};
-
-static struct resource sh73a0_dmae_resources[] = {
- DEFINE_RES_MEM(0xfe000020, 0x89e0),
- {
- .name = "error_irq",
- .start = gic_spi(129),
- .end = gic_spi(129),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-19 */
- .start = gic_spi(109),
- .end = gic_spi(128),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device dma0_device = {
- .name = "sh-dma-engine",
- .id = 0,
- .resource = sh73a0_dmae_resources,
- .num_resources = ARRAY_SIZE(sh73a0_dmae_resources),
- .dev = {
- .platform_data = &sh73a0_dmae_platform_data,
- },
-};
-
-/* MPDMAC */
-static const struct sh_dmae_slave_config sh73a0_mpdma_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_FSI2A_RX,
- .addr = 0xec230020,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xd6, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2A_TX,
- .addr = 0xec230024,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd5, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2C_RX,
- .addr = 0xec230060,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xda, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2C_TX,
- .addr = 0xec230064,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd9, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2B_RX,
- .addr = 0xec240020,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0x8e, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2B_TX,
- .addr = 0xec240024,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0x8d, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2D_RX,
- .addr = 0xec240060,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0x9a, /* CHECK ME */
- },
-};
-
-#define MPDMA_CHANNEL(a, b, c) \
-{ \
- .offset = a, \
- .dmars = b, \
- .dmars_bit = c, \
- .chclr_offset = (0x220 - 0x20) + a \
-}
-
-static const struct sh_dmae_channel sh73a0_mpdma_channels[] = {
- MPDMA_CHANNEL(0x00, 0, 0),
- MPDMA_CHANNEL(0x10, 0, 8),
- MPDMA_CHANNEL(0x20, 4, 0),
- MPDMA_CHANNEL(0x30, 4, 8),
- MPDMA_CHANNEL(0x50, 8, 0),
- MPDMA_CHANNEL(0x70, 8, 8),
-};
-
-static struct sh_dmae_pdata sh73a0_mpdma_platform_data = {
- .slave = sh73a0_mpdma_slaves,
- .slave_num = ARRAY_SIZE(sh73a0_mpdma_slaves),
- .channel = sh73a0_mpdma_channels,
- .channel_num = ARRAY_SIZE(sh73a0_mpdma_channels),
- .ts_low_shift = TS_LOW_SHIFT,
- .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
- .ts_high_shift = TS_HI_SHIFT,
- .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
- .ts_shift = dma_ts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
- .dmaor_init = DMAOR_DME,
- .chclr_present = 1,
-};
-
-/* Resource order important! */
-static struct resource sh73a0_mpdma_resources[] = {
- /* Channel registers and DMAOR */
- DEFINE_RES_MEM(0xec618020, 0x270),
- /* DMARSx */
- DEFINE_RES_MEM(0xec619000, 0xc),
- {
- .name = "error_irq",
- .start = gic_spi(181),
- .end = gic_spi(181),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(175),
- .end = gic_spi(180),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device mpdma0_device = {
- .name = "sh-dma-engine",
- .id = 1,
- .resource = sh73a0_mpdma_resources,
- .num_resources = ARRAY_SIZE(sh73a0_mpdma_resources),
- .dev = {
- .platform_data = &sh73a0_mpdma_platform_data,
- },
-};
-
-static struct resource pmu_resources[] = {
- [0] = {
- .start = gic_spi(55),
- .end = gic_spi(55),
- .flags = IORESOURCE_IRQ,
- },
- [1] = {
- .start = gic_spi(56),
- .end = gic_spi(56),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device pmu_device = {
- .name = "armv7-pmu",
- .id = -1,
- .num_resources = ARRAY_SIZE(pmu_resources),
- .resource = pmu_resources,
-};
-
-/* an IPMMU module for ICB */
-static struct resource ipmmu_resources[] = {
- DEFINE_RES_MEM(0xfe951000, 0x100),
-};
-
-static const char * const ipmmu_dev_names[] = {
- "sh_mobile_lcdc_fb.0",
-};
-
-static struct shmobile_ipmmu_platform_data ipmmu_platform_data = {
- .dev_names = ipmmu_dev_names,
- .num_dev_names = ARRAY_SIZE(ipmmu_dev_names),
-};
-
-static struct platform_device ipmmu_device = {
- .name = "ipmmu",
- .id = -1,
- .dev = {
- .platform_data = &ipmmu_platform_data,
- },
- .resource = ipmmu_resources,
- .num_resources = ARRAY_SIZE(ipmmu_resources),
-};
-
-static struct renesas_intc_irqpin_config irqpin0_platform_data = {
- .irq_base = irq_pin(0), /* IRQ0 -> IRQ7 */
- .control_parent = true,
-};
-
-static struct resource irqpin0_resources[] = {
- DEFINE_RES_MEM(0xe6900000, 4), /* ICR1A */
- DEFINE_RES_MEM(0xe6900010, 4), /* INTPRI00A */
- DEFINE_RES_MEM(0xe6900020, 1), /* INTREQ00A */
- DEFINE_RES_MEM(0xe6900040, 1), /* INTMSK00A */
- DEFINE_RES_MEM(0xe6900060, 1), /* INTMSKCLR00A */
- DEFINE_RES_IRQ(gic_spi(1)), /* IRQ0 */
- DEFINE_RES_IRQ(gic_spi(2)), /* IRQ1 */
- DEFINE_RES_IRQ(gic_spi(3)), /* IRQ2 */
- DEFINE_RES_IRQ(gic_spi(4)), /* IRQ3 */
- DEFINE_RES_IRQ(gic_spi(5)), /* IRQ4 */
- DEFINE_RES_IRQ(gic_spi(6)), /* IRQ5 */
- DEFINE_RES_IRQ(gic_spi(7)), /* IRQ6 */
- DEFINE_RES_IRQ(gic_spi(8)), /* IRQ7 */
-};
-
-static struct platform_device irqpin0_device = {
- .name = "renesas_intc_irqpin",
- .id = 0,
- .resource = irqpin0_resources,
- .num_resources = ARRAY_SIZE(irqpin0_resources),
- .dev = {
- .platform_data = &irqpin0_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin1_platform_data = {
- .irq_base = irq_pin(8), /* IRQ8 -> IRQ15 */
- .control_parent = true, /* Disable spurious IRQ10 */
-};
-
-static struct resource irqpin1_resources[] = {
- DEFINE_RES_MEM(0xe6900004, 4), /* ICR2A */
- DEFINE_RES_MEM(0xe6900014, 4), /* INTPRI10A */
- DEFINE_RES_MEM(0xe6900024, 1), /* INTREQ10A */
- DEFINE_RES_MEM(0xe6900044, 1), /* INTMSK10A */
- DEFINE_RES_MEM(0xe6900064, 1), /* INTMSKCLR10A */
- DEFINE_RES_IRQ(gic_spi(9)), /* IRQ8 */
- DEFINE_RES_IRQ(gic_spi(10)), /* IRQ9 */
- DEFINE_RES_IRQ(gic_spi(11)), /* IRQ10 */
- DEFINE_RES_IRQ(gic_spi(12)), /* IRQ11 */
- DEFINE_RES_IRQ(gic_spi(13)), /* IRQ12 */
- DEFINE_RES_IRQ(gic_spi(14)), /* IRQ13 */
- DEFINE_RES_IRQ(gic_spi(15)), /* IRQ14 */
- DEFINE_RES_IRQ(gic_spi(16)), /* IRQ15 */
-};
-
-static struct platform_device irqpin1_device = {
- .name = "renesas_intc_irqpin",
- .id = 1,
- .resource = irqpin1_resources,
- .num_resources = ARRAY_SIZE(irqpin1_resources),
- .dev = {
- .platform_data = &irqpin1_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin2_platform_data = {
- .irq_base = irq_pin(16), /* IRQ16 -> IRQ23 */
- .control_parent = true,
-};
-
-static struct resource irqpin2_resources[] = {
- DEFINE_RES_MEM(0xe6900008, 4), /* ICR3A */
- DEFINE_RES_MEM(0xe6900018, 4), /* INTPRI20A */
- DEFINE_RES_MEM(0xe6900028, 1), /* INTREQ20A */
- DEFINE_RES_MEM(0xe6900048, 1), /* INTMSK20A */
- DEFINE_RES_MEM(0xe6900068, 1), /* INTMSKCLR20A */
- DEFINE_RES_IRQ(gic_spi(17)), /* IRQ16 */
- DEFINE_RES_IRQ(gic_spi(18)), /* IRQ17 */
- DEFINE_RES_IRQ(gic_spi(19)), /* IRQ18 */
- DEFINE_RES_IRQ(gic_spi(20)), /* IRQ19 */
- DEFINE_RES_IRQ(gic_spi(21)), /* IRQ20 */
- DEFINE_RES_IRQ(gic_spi(22)), /* IRQ21 */
- DEFINE_RES_IRQ(gic_spi(23)), /* IRQ22 */
- DEFINE_RES_IRQ(gic_spi(24)), /* IRQ23 */
-};
-
-static struct platform_device irqpin2_device = {
- .name = "renesas_intc_irqpin",
- .id = 2,
- .resource = irqpin2_resources,
- .num_resources = ARRAY_SIZE(irqpin2_resources),
- .dev = {
- .platform_data = &irqpin2_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin3_platform_data = {
- .irq_base = irq_pin(24), /* IRQ24 -> IRQ31 */
- .control_parent = true,
-};
-
-static struct resource irqpin3_resources[] = {
- DEFINE_RES_MEM(0xe690000c, 4), /* ICR4A */
- DEFINE_RES_MEM(0xe690001c, 4), /* INTPRI30A */
- DEFINE_RES_MEM(0xe690002c, 1), /* INTREQ30A */
- DEFINE_RES_MEM(0xe690004c, 1), /* INTMSK30A */
- DEFINE_RES_MEM(0xe690006c, 1), /* INTMSKCLR30A */
- DEFINE_RES_IRQ(gic_spi(25)), /* IRQ24 */
- DEFINE_RES_IRQ(gic_spi(26)), /* IRQ25 */
- DEFINE_RES_IRQ(gic_spi(27)), /* IRQ26 */
- DEFINE_RES_IRQ(gic_spi(28)), /* IRQ27 */
- DEFINE_RES_IRQ(gic_spi(29)), /* IRQ28 */
- DEFINE_RES_IRQ(gic_spi(30)), /* IRQ29 */
- DEFINE_RES_IRQ(gic_spi(31)), /* IRQ30 */
- DEFINE_RES_IRQ(gic_spi(32)), /* IRQ31 */
-};
-
-static struct platform_device irqpin3_device = {
- .name = "renesas_intc_irqpin",
- .id = 3,
- .resource = irqpin3_resources,
- .num_resources = ARRAY_SIZE(irqpin3_resources),
- .dev = {
- .platform_data = &irqpin3_platform_data,
- },
-};
-
-static struct platform_device *sh73a0_early_devices[] __initdata = {
- &scif0_device,
- &scif1_device,
- &scif2_device,
- &scif3_device,
- &scif4_device,
- &scif5_device,
- &scif6_device,
- &scif7_device,
- &scif8_device,
- &tmu0_device,
- &ipmmu_device,
- &cmt1_device,
-};
-
-static struct platform_device *sh73a0_late_devices[] __initdata = {
- &i2c0_device,
- &i2c1_device,
- &i2c2_device,
- &i2c3_device,
- &i2c4_device,
- &dma0_device,
- &mpdma0_device,
- &pmu_device,
- &irqpin0_device,
- &irqpin1_device,
- &irqpin2_device,
- &irqpin3_device,
-};
-
-#define SRCR2 IOMEM(0xe61580b0)
-
-void __init sh73a0_add_standard_devices(void)
-{
- /* Clear software reset bit on SY-DMAC module */
- __raw_writel(__raw_readl(SRCR2) & ~(1 << 18), SRCR2);
-
- platform_add_devices(sh73a0_early_devices,
- ARRAY_SIZE(sh73a0_early_devices));
- platform_add_devices(sh73a0_late_devices,
- ARRAY_SIZE(sh73a0_late_devices));
-}
-
-/* do nothing for !CONFIG_SMP or !CONFIG_HAVE_TWD */
-void __init __weak sh73a0_register_twd(void) { }
-
-void __init sh73a0_earlytimer_init(void)
-{
- shmobile_init_delay();
-#ifndef CONFIG_COMMON_CLK
- sh73a0_clock_init();
-#endif
- shmobile_earlytimer_init();
- sh73a0_register_twd();
-}
-
-void __init sh73a0_add_early_devices(void)
-{
- early_platform_add_devices(sh73a0_early_devices,
- ARRAY_SIZE(sh73a0_early_devices));
-
- /* setup early console here as well */
- shmobile_setup_console();
-}
-
-#ifdef CONFIG_USE_OF
-
static void __init sh73a0_generic_init(void)
{
#ifdef CONFIG_CACHE_L2X0
@@ -807,4 +71,3 @@ DT_MACHINE_START(SH73A0_DT, "Generic SH73A0 (Flattened Device Tree)")
.init_late = shmobile_init_late,
.dt_compat = sh73a0_boards_compat_dt,
MACHINE_END
-#endif /* CONFIG_USE_OF */
diff --git a/arch/arm/mach-shmobile/sh73a0.h b/arch/arm/mach-shmobile/sh73a0.h
index 5a80f18b4fa0665f..39646806cf64646b 100644
--- a/arch/arm/mach-shmobile/sh73a0.h
+++ b/arch/arm/mach-shmobile/sh73a0.h
@@ -1,89 +1,6 @@
#ifndef __ASM_SH73A0_H__
#define __ASM_SH73A0_H__
-/* DMA slave IDs */
-enum {
- SHDMA_SLAVE_INVALID,
- SHDMA_SLAVE_SCIF0_TX,
- SHDMA_SLAVE_SCIF0_RX,
- SHDMA_SLAVE_SCIF1_TX,
- SHDMA_SLAVE_SCIF1_RX,
- SHDMA_SLAVE_SCIF2_TX,
- SHDMA_SLAVE_SCIF2_RX,
- SHDMA_SLAVE_SCIF3_TX,
- SHDMA_SLAVE_SCIF3_RX,
- SHDMA_SLAVE_SCIF4_TX,
- SHDMA_SLAVE_SCIF4_RX,
- SHDMA_SLAVE_SCIF5_TX,
- SHDMA_SLAVE_SCIF5_RX,
- SHDMA_SLAVE_SCIF6_TX,
- SHDMA_SLAVE_SCIF6_RX,
- SHDMA_SLAVE_SCIF7_TX,
- SHDMA_SLAVE_SCIF7_RX,
- SHDMA_SLAVE_SCIF8_TX,
- SHDMA_SLAVE_SCIF8_RX,
- SHDMA_SLAVE_SDHI0_TX,
- SHDMA_SLAVE_SDHI0_RX,
- SHDMA_SLAVE_SDHI1_TX,
- SHDMA_SLAVE_SDHI1_RX,
- SHDMA_SLAVE_SDHI2_TX,
- SHDMA_SLAVE_SDHI2_RX,
- SHDMA_SLAVE_MMCIF_TX,
- SHDMA_SLAVE_MMCIF_RX,
- SHDMA_SLAVE_FSI2A_TX,
- SHDMA_SLAVE_FSI2A_RX,
- SHDMA_SLAVE_FSI2B_TX,
- SHDMA_SLAVE_FSI2B_RX,
- SHDMA_SLAVE_FSI2C_TX,
- SHDMA_SLAVE_FSI2C_RX,
- SHDMA_SLAVE_FSI2D_RX,
-};
-
-/*
- * SH73A0 IRQ LOCATION TABLE
- *
- * 416 -----------------------------------------
- * IRQ0-IRQ15
- * 431 -----------------------------------------
- * ...
- * 448 -----------------------------------------
- * sh73a0-intcs
- * sh73a0-intca-irq-pins
- * 680 -----------------------------------------
- * ...
- * 700 -----------------------------------------
- * sh73a0-pint0
- * 731 -----------------------------------------
- * 732 -----------------------------------------
- * sh73a0-pint1
- * 739 -----------------------------------------
- * ...
- * 800 -----------------------------------------
- * IRQ16-IRQ31
- * 815 -----------------------------------------
- * ...
- * 928 -----------------------------------------
- * sh73a0-intca-irq-pins
- * 943 -----------------------------------------
- */
-
-/* PINT interrupts are located at Linux IRQ 700 and up */
-#define SH73A0_PINT0_IRQ(irq) ((irq) + 700)
-#define SH73A0_PINT1_IRQ(irq) ((irq) + 732)
-
-extern void sh73a0_init_irq(void);
-extern void sh73a0_init_irq_dt(void);
-extern void sh73a0_map_io(void);
-extern void sh73a0_earlytimer_init(void);
-extern void sh73a0_add_early_devices(void);
-extern void sh73a0_add_standard_devices(void);
-extern void sh73a0_clock_init(void);
-extern void sh73a0_pinmux_init(void);
-extern void sh73a0_pm_init(void);
-extern struct clk sh73a0_extal1_clk;
-extern struct clk sh73a0_extal2_clk;
-extern struct clk sh73a0_extcki_clk;
-extern struct clk sh73a0_extalr_clk;
extern struct smp_operations sh73a0_smp_ops;
#endif /* __ASM_SH73A0_H__ */
diff --git a/arch/arm/mach-shmobile/smp-sh73a0.c b/arch/arm/mach-shmobile/smp-sh73a0.c
index 2106d6b76a069392..d03aa11fb46dad19 100644
--- a/arch/arm/mach-shmobile/smp-sh73a0.c
+++ b/arch/arm/mach-shmobile/smp-sh73a0.c
@@ -33,14 +33,6 @@
#define SH73A0_SCU_BASE 0xf0000000
-#if defined(CONFIG_HAVE_ARM_TWD) && !defined(CONFIG_ARCH_MULTIPLATFORM)
-static DEFINE_TWD_LOCAL_TIMER(twd_local_timer, SH73A0_SCU_BASE + 0x600, 29);
-void __init sh73a0_register_twd(void)
-{
- twd_local_timer_register(&twd_local_timer);
-}
-#endif
-
static int sh73a0_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned int lcpu = cpu_logical_map(cpu);
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 04/15] ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the SH-Mobile AG5 (sh73a0) legacy SoC code was the
KZM-A9-GT legacy board code, which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 9 -
arch/arm/mach-shmobile/Makefile | 3 +-
arch/arm/mach-shmobile/clock-sh73a0.c | 752 ----------------------------------
arch/arm/mach-shmobile/pm-sh73a0.c | 32 --
arch/arm/mach-shmobile/setup-sh73a0.c | 739 +--------------------------------
arch/arm/mach-shmobile/sh73a0.h | 83 ----
arch/arm/mach-shmobile/smp-sh73a0.c | 8 -
7 files changed, 2 insertions(+), 1624 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/clock-sh73a0.c
delete mode 100644 arch/arm/mach-shmobile/pm-sh73a0.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 2a4d8348b6299dff..bc8e2f60fe505ee2 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -108,15 +108,6 @@ if ARCH_SHMOBILE_LEGACY
comment "Renesas ARM SoCs System Type"
-config ARCH_SH73A0
- bool "SH-Mobile AG5 (R8A73A00)"
- select ARCH_RMOBILE
- select ARCH_WANT_OPTIONAL_GPIOLIB
- select ARM_GIC
- select I2C
- select SH_INTC
- select RENESAS_INTC_IRQPIN
-
config ARCH_R8A7740
bool "R-Mobile A1 (R8A77400)"
select ARCH_RMOBILE
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 9bdb8a11acb10c4e..7e20ab3021be0ff2 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -6,7 +6,7 @@
obj-y := timer.o console.o
# CPU objects
-obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o pm-sh73a0.o
+obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o
obj-$(CONFIG_ARCH_R8A73A4) += setup-r8a73a4.o
obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o pm-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += setup-r8a7778.o
@@ -21,7 +21,6 @@ obj-$(CONFIG_ARCH_R7S72100) += setup-r7s72100.o
# Clock objects
ifndef CONFIG_COMMON_CLK
obj-y += clock.o
-obj-$(CONFIG_ARCH_SH73A0) += clock-sh73a0.o
obj-$(CONFIG_ARCH_R8A7740) += clock-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += clock-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += clock-r8a7779.o
diff --git a/arch/arm/mach-shmobile/clock-sh73a0.c b/arch/arm/mach-shmobile/clock-sh73a0.c
deleted file mode 100644
index 3855fb024fdbb1ca..0000000000000000
--- a/arch/arm/mach-shmobile/clock-sh73a0.c
+++ /dev/null
@@ -1,752 +0,0 @@
-/*
- * sh73a0 clock framework support
- *
- * Copyright (C) 2010 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/sh_clk.h>
-#include <linux/clkdev.h>
-#include <asm/processor.h>
-#include "clock.h"
-#include "common.h"
-
-#define FRQCRA IOMEM(0xe6150000)
-#define FRQCRB IOMEM(0xe6150004)
-#define FRQCRD IOMEM(0xe61500e4)
-#define VCLKCR1 IOMEM(0xe6150008)
-#define VCLKCR2 IOMEM(0xe615000C)
-#define VCLKCR3 IOMEM(0xe615001C)
-#define ZBCKCR IOMEM(0xe6150010)
-#define FLCKCR IOMEM(0xe6150014)
-#define SD0CKCR IOMEM(0xe6150074)
-#define SD1CKCR IOMEM(0xe6150078)
-#define SD2CKCR IOMEM(0xe615007C)
-#define FSIACKCR IOMEM(0xe6150018)
-#define FSIBCKCR IOMEM(0xe6150090)
-#define SUBCKCR IOMEM(0xe6150080)
-#define SPUACKCR IOMEM(0xe6150084)
-#define SPUVCKCR IOMEM(0xe6150094)
-#define MSUCKCR IOMEM(0xe6150088)
-#define HSICKCR IOMEM(0xe615008C)
-#define MFCK1CR IOMEM(0xe6150098)
-#define MFCK2CR IOMEM(0xe615009C)
-#define DSITCKCR IOMEM(0xe6150060)
-#define DSI0PCKCR IOMEM(0xe6150064)
-#define DSI1PCKCR IOMEM(0xe6150068)
-#define DSI0PHYCR 0xe615006C
-#define DSI1PHYCR 0xe6150070
-#define PLLECR IOMEM(0xe61500d0)
-#define PLL0CR IOMEM(0xe61500d8)
-#define PLL1CR IOMEM(0xe6150028)
-#define PLL2CR IOMEM(0xe615002c)
-#define PLL3CR IOMEM(0xe61500dc)
-#define SMSTPCR0 IOMEM(0xe6150130)
-#define SMSTPCR1 IOMEM(0xe6150134)
-#define SMSTPCR2 IOMEM(0xe6150138)
-#define SMSTPCR3 IOMEM(0xe615013c)
-#define SMSTPCR4 IOMEM(0xe6150140)
-#define SMSTPCR5 IOMEM(0xe6150144)
-#define CKSCR IOMEM(0xe61500c0)
-
-/* Fixed 32 KHz root clock from EXTALR pin */
-static struct clk r_clk = {
- .rate = 32768,
-};
-
-/*
- * 26MHz default rate for the EXTAL1 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-struct clk sh73a0_extal1_clk = {
- .rate = 26000000,
-};
-
-/*
- * 48MHz default rate for the EXTAL2 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-struct clk sh73a0_extal2_clk = {
- .rate = 48000000,
-};
-
-static struct sh_clk_ops main_clk_ops = {
- .recalc = followparent_recalc,
-};
-
-/* Main clock */
-static struct clk main_clk = {
- /* .parent wll be set on sh73a0_clock_init() */
- .ops = &main_clk_ops,
-};
-
-/* PLL0, PLL1, PLL2, PLL3 */
-static unsigned long pll_recalc(struct clk *clk)
-{
- unsigned long mult = 1;
-
- if (__raw_readl(PLLECR) & (1 << clk->enable_bit)) {
- mult = (((__raw_readl(clk->enable_reg) >> 24) & 0x3f) + 1);
- /* handle CFG bit for PLL1 and PLL2 */
- switch (clk->enable_bit) {
- case 1:
- case 2:
- if (__raw_readl(clk->enable_reg) & (1 << 20))
- mult *= 2;
- }
- }
-
- return clk->parent->rate * mult;
-}
-
-static struct sh_clk_ops pll_clk_ops = {
- .recalc = pll_recalc,
-};
-
-static struct clk pll0_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL0CR,
- .enable_bit = 0,
-};
-
-static struct clk pll1_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL1CR,
- .enable_bit = 1,
-};
-
-static struct clk pll2_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL2CR,
- .enable_bit = 2,
-};
-
-static struct clk pll3_clk = {
- .ops = &pll_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &main_clk,
- .enable_reg = (void __iomem *)PLL3CR,
- .enable_bit = 3,
-};
-
-/* A fixed divide block */
-SH_CLK_RATIO(div2, 1, 2);
-SH_CLK_RATIO(div7, 1, 7);
-SH_CLK_RATIO(div13, 1, 13);
-
-SH_FIXED_RATIO_CLK(extal1_div2_clk, sh73a0_extal1_clk, div2);
-SH_FIXED_RATIO_CLK(extal2_div2_clk, sh73a0_extal2_clk, div2);
-SH_FIXED_RATIO_CLK(main_div2_clk, main_clk, div2);
-SH_FIXED_RATIO_CLK(pll1_div2_clk, pll1_clk, div2);
-SH_FIXED_RATIO_CLK(pll1_div7_clk, pll1_clk, div7);
-SH_FIXED_RATIO_CLK(pll1_div13_clk, pll1_clk, div13);
-
-/* External input clock */
-struct clk sh73a0_extcki_clk = {
-};
-
-struct clk sh73a0_extalr_clk = {
-};
-
-static struct clk *main_clks[] = {
- &r_clk,
- &sh73a0_extal1_clk,
- &sh73a0_extal2_clk,
- &extal1_div2_clk,
- &extal2_div2_clk,
- &main_clk,
- &main_div2_clk,
- &pll0_clk,
- &pll1_clk,
- &pll2_clk,
- &pll3_clk,
- &pll1_div2_clk,
- &pll1_div7_clk,
- &pll1_div13_clk,
- &sh73a0_extcki_clk,
- &sh73a0_extalr_clk,
-};
-
-static int frqcr_kick(void)
-{
- int i;
-
- /* set KICK bit in FRQCRB to update hardware setting, check success */
- __raw_writel(__raw_readl(FRQCRB) | (1 << 31), FRQCRB);
- for (i = 1000; i; i--)
- if (__raw_readl(FRQCRB) & (1 << 31))
- cpu_relax();
- else
- return i;
-
- return -ETIMEDOUT;
-}
-
-static void div4_kick(struct clk *clk)
-{
- frqcr_kick();
-}
-
-static int divisors[] = { 2, 3, 4, 6, 8, 12, 16, 18,
- 24, 0, 36, 48, 7 };
-
-static struct clk_div_mult_table div4_div_mult_table = {
- .divisors = divisors,
- .nr_divisors = ARRAY_SIZE(divisors),
-};
-
-static struct clk_div4_table div4_table = {
- .div_mult_table = &div4_div_mult_table,
- .kick = div4_kick,
-};
-
-enum { DIV4_I, DIV4_ZG, DIV4_M3, DIV4_B, DIV4_M1, DIV4_M2,
- DIV4_Z, DIV4_ZX, DIV4_HP, DIV4_NR };
-
-#define DIV4(_reg, _bit, _mask, _flags) \
- SH_CLK_DIV4(&pll1_clk, _reg, _bit, _mask, _flags)
-
-static struct clk div4_clks[DIV4_NR] = {
- [DIV4_I] = DIV4(FRQCRA, 20, 0xdff, CLK_ENABLE_ON_INIT),
- /*
- * ZG clock is dividing PLL0 frequency to supply SGX. Make sure not to
- * exceed maximum frequencies of 201.5MHz for VDD_DVFS=1.175 and
- * 239.2MHz for VDD_DVFS=1.315V.
- */
- [DIV4_ZG] = SH_CLK_DIV4(&pll0_clk, FRQCRA, 16, 0xd7f, CLK_ENABLE_ON_INIT),
- [DIV4_M3] = DIV4(FRQCRA, 12, 0x1dff, CLK_ENABLE_ON_INIT),
- [DIV4_B] = DIV4(FRQCRA, 8, 0xdff, CLK_ENABLE_ON_INIT),
- [DIV4_M1] = DIV4(FRQCRA, 4, 0x1dff, 0),
- [DIV4_M2] = DIV4(FRQCRA, 0, 0x1dff, 0),
- [DIV4_Z] = SH_CLK_DIV4(&pll0_clk, FRQCRB, 24, 0x97f, 0),
- [DIV4_ZX] = DIV4(FRQCRB, 12, 0xdff, 0),
- [DIV4_HP] = DIV4(FRQCRB, 4, 0xdff, 0),
-};
-
-static unsigned long twd_recalc(struct clk *clk)
-{
- return clk_get_rate(clk->parent) / 4;
-}
-
-static struct sh_clk_ops twd_clk_ops = {
- .recalc = twd_recalc,
-};
-
-static struct clk twd_clk = {
- .parent = &div4_clks[DIV4_Z],
- .ops = &twd_clk_ops,
-};
-
-static struct sh_clk_ops zclk_ops, kicker_ops;
-static const struct sh_clk_ops *div4_clk_ops;
-
-static int zclk_set_rate(struct clk *clk, unsigned long rate)
-{
- int ret;
-
- if (!clk->parent || !__clk_get(clk->parent))
- return -ENODEV;
-
- if (readl(FRQCRB) & (1 << 31))
- return -EBUSY;
-
- if (rate == clk_get_rate(clk->parent)) {
- /* 1:1 - switch off divider */
- __raw_writel(__raw_readl(FRQCRB) & ~(1 << 28), FRQCRB);
- /* nullify the divider to prepare for the next time */
- ret = div4_clk_ops->set_rate(clk, rate / 2);
- if (!ret)
- ret = frqcr_kick();
- if (ret > 0)
- ret = 0;
- } else {
- /* Enable the divider */
- __raw_writel(__raw_readl(FRQCRB) | (1 << 28), FRQCRB);
-
- ret = frqcr_kick();
- if (ret >= 0)
- /*
- * set the divider - call the DIV4 method, it will kick
- * FRQCRB too
- */
- ret = div4_clk_ops->set_rate(clk, rate);
- if (ret < 0)
- goto esetrate;
- }
-
-esetrate:
- __clk_put(clk->parent);
- return ret;
-}
-
-static long zclk_round_rate(struct clk *clk, unsigned long rate)
-{
- unsigned long div_freq = div4_clk_ops->round_rate(clk, rate),
- parent_freq = clk_get_rate(clk->parent);
-
- if (rate > div_freq && abs(parent_freq - rate) < rate - div_freq)
- return parent_freq;
-
- return div_freq;
-}
-
-static unsigned long zclk_recalc(struct clk *clk)
-{
- /*
- * Must recalculate frequencies in case PLL0 has been changed, even if
- * the divisor is unused ATM!
- */
- unsigned long div_freq = div4_clk_ops->recalc(clk);
-
- if (__raw_readl(FRQCRB) & (1 << 28))
- return div_freq;
-
- return clk_get_rate(clk->parent);
-}
-
-static int kicker_set_rate(struct clk *clk, unsigned long rate)
-{
- if (__raw_readl(FRQCRB) & (1 << 31))
- return -EBUSY;
-
- return div4_clk_ops->set_rate(clk, rate);
-}
-
-static void div4_clk_extend(void)
-{
- int i;
-
- div4_clk_ops = div4_clks[0].ops;
-
- /* Add a kicker-busy check before changing the rate */
- kicker_ops = *div4_clk_ops;
- /* We extend the DIV4 clock with a 1:1 pass-through case */
- zclk_ops = *div4_clk_ops;
-
- kicker_ops.set_rate = kicker_set_rate;
- zclk_ops.set_rate = zclk_set_rate;
- zclk_ops.round_rate = zclk_round_rate;
- zclk_ops.recalc = zclk_recalc;
-
- for (i = 0; i < DIV4_NR; i++)
- div4_clks[i].ops = i == DIV4_Z ? &zclk_ops : &kicker_ops;
-}
-
-enum { DIV6_VCK1, DIV6_VCK2, DIV6_VCK3, DIV6_ZB1,
- DIV6_FLCTL, DIV6_SDHI0, DIV6_SDHI1, DIV6_SDHI2,
- DIV6_FSIA, DIV6_FSIB, DIV6_SUB,
- DIV6_SPUA, DIV6_SPUV, DIV6_MSU,
- DIV6_HSI, DIV6_MFG1, DIV6_MFG2,
- DIV6_DSIT, DIV6_DSI0P, DIV6_DSI1P,
- DIV6_NR };
-
-static struct clk *vck_parent[8] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &sh73a0_extcki_clk,
- [3] = &sh73a0_extal2_clk,
- [4] = &main_div2_clk,
- [5] = &sh73a0_extalr_clk,
- [6] = &main_clk,
-};
-
-static struct clk *pll_parent[4] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &pll1_div13_clk,
-};
-
-static struct clk *hsi_parent[4] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &pll1_div7_clk,
-};
-
-static struct clk *pll_extal2_parent[] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &sh73a0_extal2_clk,
- [3] = &sh73a0_extal2_clk,
-};
-
-static struct clk *dsi_parent[8] = {
- [0] = &pll1_div2_clk,
- [1] = &pll2_clk,
- [2] = &main_clk,
- [3] = &sh73a0_extal2_clk,
- [4] = &sh73a0_extcki_clk,
-};
-
-static struct clk div6_clks[DIV6_NR] = {
- [DIV6_VCK1] = SH_CLK_DIV6_EXT(VCLKCR1, 0,
- vck_parent, ARRAY_SIZE(vck_parent), 12, 3),
- [DIV6_VCK2] = SH_CLK_DIV6_EXT(VCLKCR2, 0,
- vck_parent, ARRAY_SIZE(vck_parent), 12, 3),
- [DIV6_VCK3] = SH_CLK_DIV6_EXT(VCLKCR3, 0,
- vck_parent, ARRAY_SIZE(vck_parent), 12, 3),
- [DIV6_ZB1] = SH_CLK_DIV6_EXT(ZBCKCR, CLK_ENABLE_ON_INIT,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_FLCTL] = SH_CLK_DIV6_EXT(FLCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_SDHI0] = SH_CLK_DIV6_EXT(SD0CKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 2),
- [DIV6_SDHI1] = SH_CLK_DIV6_EXT(SD1CKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 2),
- [DIV6_SDHI2] = SH_CLK_DIV6_EXT(SD2CKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 2),
- [DIV6_FSIA] = SH_CLK_DIV6_EXT(FSIACKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 1),
- [DIV6_FSIB] = SH_CLK_DIV6_EXT(FSIBCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 6, 1),
- [DIV6_SUB] = SH_CLK_DIV6_EXT(SUBCKCR, 0,
- pll_extal2_parent, ARRAY_SIZE(pll_extal2_parent), 6, 2),
- [DIV6_SPUA] = SH_CLK_DIV6_EXT(SPUACKCR, 0,
- pll_extal2_parent, ARRAY_SIZE(pll_extal2_parent), 6, 2),
- [DIV6_SPUV] = SH_CLK_DIV6_EXT(SPUVCKCR, 0,
- pll_extal2_parent, ARRAY_SIZE(pll_extal2_parent), 6, 2),
- [DIV6_MSU] = SH_CLK_DIV6_EXT(MSUCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_HSI] = SH_CLK_DIV6_EXT(HSICKCR, 0,
- hsi_parent, ARRAY_SIZE(hsi_parent), 6, 2),
- [DIV6_MFG1] = SH_CLK_DIV6_EXT(MFCK1CR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_MFG2] = SH_CLK_DIV6_EXT(MFCK2CR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_DSIT] = SH_CLK_DIV6_EXT(DSITCKCR, 0,
- pll_parent, ARRAY_SIZE(pll_parent), 7, 1),
- [DIV6_DSI0P] = SH_CLK_DIV6_EXT(DSI0PCKCR, 0,
- dsi_parent, ARRAY_SIZE(dsi_parent), 12, 3),
- [DIV6_DSI1P] = SH_CLK_DIV6_EXT(DSI1PCKCR, 0,
- dsi_parent, ARRAY_SIZE(dsi_parent), 12, 3),
-};
-
-/* DSI DIV */
-static unsigned long dsiphy_recalc(struct clk *clk)
-{
- u32 value;
-
- value = __raw_readl(clk->mapping->base);
-
- /* FIXME */
- if (!(value & 0x000B8000))
- return clk->parent->rate;
-
- value &= 0x3f;
- value += 1;
-
- if ((value < 12) ||
- (value > 33)) {
- pr_err("DSIPHY has wrong value (%d)", value);
- return 0;
- }
-
- return clk->parent->rate / value;
-}
-
-static long dsiphy_round_rate(struct clk *clk, unsigned long rate)
-{
- return clk_rate_mult_range_round(clk, 12, 33, rate);
-}
-
-static void dsiphy_disable(struct clk *clk)
-{
- u32 value;
-
- value = __raw_readl(clk->mapping->base);
- value &= ~0x000B8000;
-
- __raw_writel(value , clk->mapping->base);
-}
-
-static int dsiphy_enable(struct clk *clk)
-{
- u32 value;
- int multi;
-
- value = __raw_readl(clk->mapping->base);
- multi = (value & 0x3f) + 1;
-
- if ((multi < 12) || (multi > 33))
- return -EIO;
-
- __raw_writel(value | 0x000B8000, clk->mapping->base);
-
- return 0;
-}
-
-static int dsiphy_set_rate(struct clk *clk, unsigned long rate)
-{
- u32 value;
- int idx;
-
- idx = rate / clk->parent->rate;
- if ((idx < 12) || (idx > 33))
- return -EINVAL;
-
- idx += -1;
-
- value = __raw_readl(clk->mapping->base);
- value = (value & ~0x3f) + idx;
-
- __raw_writel(value, clk->mapping->base);
-
- return 0;
-}
-
-static struct sh_clk_ops dsiphy_clk_ops = {
- .recalc = dsiphy_recalc,
- .round_rate = dsiphy_round_rate,
- .set_rate = dsiphy_set_rate,
- .enable = dsiphy_enable,
- .disable = dsiphy_disable,
-};
-
-static struct clk_mapping dsi0phy_clk_mapping = {
- .phys = DSI0PHYCR,
- .len = 4,
-};
-
-static struct clk_mapping dsi1phy_clk_mapping = {
- .phys = DSI1PHYCR,
- .len = 4,
-};
-
-static struct clk dsi0phy_clk = {
- .ops = &dsiphy_clk_ops,
- .parent = &div6_clks[DIV6_DSI0P], /* late install */
- .mapping = &dsi0phy_clk_mapping,
-};
-
-static struct clk dsi1phy_clk = {
- .ops = &dsiphy_clk_ops,
- .parent = &div6_clks[DIV6_DSI1P], /* late install */
- .mapping = &dsi1phy_clk_mapping,
-};
-
-static struct clk *late_main_clks[] = {
- &dsi0phy_clk,
- &dsi1phy_clk,
- &twd_clk,
-};
-
-enum { MSTP001,
- MSTP129, MSTP128, MSTP127, MSTP126, MSTP125, MSTP118, MSTP116, MSTP112, MSTP100,
- MSTP219, MSTP218, MSTP217,
- MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
- MSTP331, MSTP329, MSTP328, MSTP325, MSTP323, MSTP322,
- MSTP314, MSTP313, MSTP312, MSTP311,
- MSTP304, MSTP303, MSTP302, MSTP301, MSTP300,
- MSTP411, MSTP410, MSTP403,
- MSTP508,
- MSTP_NR };
-
-#define MSTP(_parent, _reg, _bit, _flags) \
- SH_CLK_MSTP32(_parent, _reg, _bit, _flags)
-
-static struct clk mstp_clks[MSTP_NR] = {
- [MSTP001] = MSTP(&div4_clks[DIV4_HP], SMSTPCR0, 1, 0), /* IIC2 */
- [MSTP129] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 29, 0), /* CEU1 */
- [MSTP128] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 28, 0), /* CSI2-RX1 */
- [MSTP127] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 27, 0), /* CEU0 */
- [MSTP126] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 26, 0), /* CSI2-RX0 */
- [MSTP125] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR1, 25, 0), /* TMU0 */
- [MSTP118] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 18, 0), /* DSITX0 */
- [MSTP116] = MSTP(&div4_clks[DIV4_HP], SMSTPCR1, 16, 0), /* IIC0 */
- [MSTP112] = MSTP(&div4_clks[DIV4_ZG], SMSTPCR1, 12, 0), /* SGX */
- [MSTP100] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 0, 0), /* LCDC0 */
- [MSTP219] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 19, 0), /* SCIFA7 */
- [MSTP218] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* SY-DMAC */
- [MSTP217] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 17, 0), /* MP-DMAC */
- [MSTP207] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */
- [MSTP206] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */
- [MSTP204] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */
- [MSTP203] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 3, 0), /* SCIFA1 */
- [MSTP202] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 2, 0), /* SCIFA2 */
- [MSTP201] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 1, 0), /* SCIFA3 */
- [MSTP200] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 0, 0), /* SCIFA4 */
- [MSTP331] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 31, 0), /* SCIFA6 */
- [MSTP329] = MSTP(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */
- [MSTP328] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 28, 0), /*FSI*/
- [MSTP325] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 25, 0), /* IrDA */
- [MSTP323] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 23, 0), /* IIC1 */
- [MSTP322] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 22, 0), /* USB */
- [MSTP314] = MSTP(&div6_clks[DIV6_SDHI0], SMSTPCR3, 14, 0), /* SDHI0 */
- [MSTP313] = MSTP(&div6_clks[DIV6_SDHI1], SMSTPCR3, 13, 0), /* SDHI1 */
- [MSTP312] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 12, 0), /* MMCIF0 */
- [MSTP311] = MSTP(&div6_clks[DIV6_SDHI2], SMSTPCR3, 11, 0), /* SDHI2 */
- [MSTP304] = MSTP(&main_div2_clk, SMSTPCR3, 4, 0), /* TPU0 */
- [MSTP303] = MSTP(&main_div2_clk, SMSTPCR3, 3, 0), /* TPU1 */
- [MSTP302] = MSTP(&main_div2_clk, SMSTPCR3, 2, 0), /* TPU2 */
- [MSTP301] = MSTP(&main_div2_clk, SMSTPCR3, 1, 0), /* TPU3 */
- [MSTP300] = MSTP(&main_div2_clk, SMSTPCR3, 0, 0), /* TPU4 */
- [MSTP411] = MSTP(&div4_clks[DIV4_HP], SMSTPCR4, 11, 0), /* IIC3 */
- [MSTP410] = MSTP(&div4_clks[DIV4_HP], SMSTPCR4, 10, 0), /* IIC4 */
- [MSTP403] = MSTP(&r_clk, SMSTPCR4, 3, 0), /* KEYSC */
- [MSTP508] = MSTP(&div4_clks[DIV4_HP], SMSTPCR5, 8, 0), /* INTCA0 */
-};
-
-/* The lookups structure below includes duplicate entries for some clocks
- * with alternate names.
- * - The traditional name used when a device is initialised with platform data
- * - The name used when a device is initialised using device tree
- * The longer-term aim is to remove these duplicates, and indeed the
- * lookups table entirely, by describing clocks using device tree.
- */
-static struct clk_lookup lookups[] = {
- /* main clocks */
- CLKDEV_CON_ID("r_clk", &r_clk),
- CLKDEV_DEV_ID("smp_twd", &twd_clk), /* smp_twd */
-
- /* DIV4 clocks */
- CLKDEV_DEV_ID("cpu0", &div4_clks[DIV4_Z]),
-
- /* DIV6 clocks */
- CLKDEV_CON_ID("vck1_clk", &div6_clks[DIV6_VCK1]),
- CLKDEV_CON_ID("vck2_clk", &div6_clks[DIV6_VCK2]),
- CLKDEV_CON_ID("vck3_clk", &div6_clks[DIV6_VCK3]),
- CLKDEV_CON_ID("sdhi0_clk", &div6_clks[DIV6_SDHI0]),
- CLKDEV_CON_ID("sdhi1_clk", &div6_clks[DIV6_SDHI1]),
- CLKDEV_CON_ID("sdhi2_clk", &div6_clks[DIV6_SDHI2]),
-
- /* MSTP32 clocks */
- CLKDEV_DEV_ID("i2c-sh_mobile.2", &mstp_clks[MSTP001]), /* I2C2 */
- CLKDEV_DEV_ID("e6824000.i2c", &mstp_clks[MSTP001]), /* I2C2 */
- CLKDEV_DEV_ID("sh_mobile_ceu.1", &mstp_clks[MSTP129]), /* CEU1 */
- CLKDEV_DEV_ID("sh-mobile-csi2.1", &mstp_clks[MSTP128]), /* CSI2-RX1 */
- CLKDEV_DEV_ID("sh_mobile_ceu.0", &mstp_clks[MSTP127]), /* CEU0 */
- CLKDEV_DEV_ID("sh-mobile-csi2.0", &mstp_clks[MSTP126]), /* CSI2-RX0 */
- CLKDEV_DEV_ID("sh-mipi-dsi.0", &mstp_clks[MSTP118]), /* DSITX */
- CLKDEV_DEV_ID("i2c-sh_mobile.0", &mstp_clks[MSTP116]), /* I2C0 */
- CLKDEV_DEV_ID("e6820000.i2c", &mstp_clks[MSTP116]), /* I2C0 */
- CLKDEV_DEV_ID("sh_mobile_lcdc_fb.0", &mstp_clks[MSTP100]), /* LCDC0 */
- CLKDEV_DEV_ID("sh-sci.7", &mstp_clks[MSTP219]), /* SCIFA7 */
- CLKDEV_DEV_ID("e6cd0000.serial", &mstp_clks[MSTP219]), /* SCIFA7 */
- CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]), /* SY-DMAC */
- CLKDEV_DEV_ID("sh-dma-engine.1", &mstp_clks[MSTP217]), /* MP-DMAC */
- CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
- CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]), /* SCIFA5 */
- CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]), /* SCIFB */
- CLKDEV_DEV_ID("e6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
- CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
- CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]), /* SCIFA0 */
- CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */
- CLKDEV_DEV_ID("e6c50000.serial", &mstp_clks[MSTP203]), /* SCIFA1 */
- CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP202]), /* SCIFA2 */
- CLKDEV_DEV_ID("e6c60000.serial", &mstp_clks[MSTP202]), /* SCIFA2 */
- CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP201]), /* SCIFA3 */
- CLKDEV_DEV_ID("e6c70000.serial", &mstp_clks[MSTP201]), /* SCIFA3 */
- CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP200]), /* SCIFA4 */
- CLKDEV_DEV_ID("e6c80000.serial", &mstp_clks[MSTP200]), /* SCIFA4 */
- CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP331]), /* SCIFA6 */
- CLKDEV_DEV_ID("e6cc0000.serial", &mstp_clks[MSTP331]), /* SCIFA6 */
- CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]), /* FSI */
- CLKDEV_DEV_ID("ec230000.sound", &mstp_clks[MSTP328]), /* FSI */
- CLKDEV_DEV_ID("sh_irda.0", &mstp_clks[MSTP325]), /* IrDA */
- CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]), /* I2C1 */
- CLKDEV_DEV_ID("e6822000.i2c", &mstp_clks[MSTP323]), /* I2C1 */
- CLKDEV_DEV_ID("renesas_usbhs", &mstp_clks[MSTP322]), /* USB */
- CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP314]), /* SDHI0 */
- CLKDEV_DEV_ID("ee100000.sd", &mstp_clks[MSTP314]), /* SDHI0 */
- CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP313]), /* SDHI1 */
- CLKDEV_DEV_ID("ee120000.sd", &mstp_clks[MSTP313]), /* SDHI1 */
- CLKDEV_DEV_ID("sh_mmcif.0", &mstp_clks[MSTP312]), /* MMCIF0 */
- CLKDEV_DEV_ID("e6bd0000.mmc", &mstp_clks[MSTP312]), /* MMCIF0 */
- CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP311]), /* SDHI2 */
- CLKDEV_DEV_ID("ee140000.sd", &mstp_clks[MSTP311]), /* SDHI2 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.0", &mstp_clks[MSTP304]), /* TPU0 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.1", &mstp_clks[MSTP303]), /* TPU1 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.2", &mstp_clks[MSTP302]), /* TPU2 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.3", &mstp_clks[MSTP301]), /* TPU3 */
- CLKDEV_DEV_ID("renesas-tpu-pwm.4", &mstp_clks[MSTP300]), /* TPU4 */
- CLKDEV_DEV_ID("i2c-sh_mobile.3", &mstp_clks[MSTP411]), /* I2C3 */
- CLKDEV_DEV_ID("e6826000.i2c", &mstp_clks[MSTP411]), /* I2C3 */
- CLKDEV_DEV_ID("i2c-sh_mobile.4", &mstp_clks[MSTP410]), /* I2C4 */
- CLKDEV_DEV_ID("e6828000.i2c", &mstp_clks[MSTP410]), /* I2C4 */
- CLKDEV_DEV_ID("sh_keysc.0", &mstp_clks[MSTP403]), /* KEYSC */
- CLKDEV_DEV_ID("renesas_intc_irqpin.0", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e6900000.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("renesas_intc_irqpin.1", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e6900004.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("renesas_intc_irqpin.2", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e6900008.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("renesas_intc_irqpin.3", &mstp_clks[MSTP508]), /* INTCA0 */
- CLKDEV_DEV_ID("e690000c.irqpin", &mstp_clks[MSTP508]), /* INTCA0 */
-
- /* ICK */
- CLKDEV_ICK_ID("dsit_clk", "sh-mipi-dsi.0", &div6_clks[DIV6_DSIT]),
- CLKDEV_ICK_ID("dsit_clk", "sh-mipi-dsi.1", &div6_clks[DIV6_DSIT]),
- CLKDEV_ICK_ID("dsip_clk", "sh-mipi-dsi.0", &div6_clks[DIV6_DSI0P]),
- CLKDEV_ICK_ID("dsip_clk", "sh-mipi-dsi.1", &div6_clks[DIV6_DSI1P]),
- CLKDEV_ICK_ID("dsiphy_clk", "sh-mipi-dsi.0", &dsi0phy_clk),
- CLKDEV_ICK_ID("dsiphy_clk", "sh-mipi-dsi.1", &dsi1phy_clk),
- CLKDEV_ICK_ID("fck", "sh-cmt-48.1", &mstp_clks[MSTP329]), /* CMT1 */
- CLKDEV_ICK_ID("fck", "e6138000.timer", &mstp_clks[MSTP329]), /* CMT1 */
- CLKDEV_ICK_ID("fck", "sh-tmu.0", &mstp_clks[MSTP125]), /* TMU0 */
-};
-
-void __init sh73a0_clock_init(void)
-{
- int k, ret = 0;
-
- /* Set SDHI clocks to a known state */
- __raw_writel(0x108, SD0CKCR);
- __raw_writel(0x108, SD1CKCR);
- __raw_writel(0x108, SD2CKCR);
-
- /* detect main clock parent */
- switch ((__raw_readl(CKSCR) >> 28) & 0x03) {
- case 0:
- main_clk.parent = &sh73a0_extal1_clk;
- break;
- case 1:
- main_clk.parent = &extal1_div2_clk;
- break;
- case 2:
- main_clk.parent = &sh73a0_extal2_clk;
- break;
- case 3:
- main_clk.parent = &extal2_div2_clk;
- break;
- }
-
- for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
- ret = clk_register(main_clks[k]);
-
- if (!ret) {
- ret = sh_clk_div4_register(div4_clks, DIV4_NR, &div4_table);
- if (!ret)
- div4_clk_extend();
- }
-
- if (!ret)
- ret = sh_clk_div6_reparent_register(div6_clks, DIV6_NR);
-
- if (!ret)
- ret = sh_clk_mstp_register(mstp_clks, MSTP_NR);
-
- for (k = 0; !ret && (k < ARRAY_SIZE(late_main_clks)); k++)
- ret = clk_register(late_main_clks[k]);
-
- clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-
- if (!ret)
- shmobile_clk_init();
- else
- panic("failed to setup sh73a0 clocks\n");
-}
diff --git a/arch/arm/mach-shmobile/pm-sh73a0.c b/arch/arm/mach-shmobile/pm-sh73a0.c
deleted file mode 100644
index a7e466817965e3b8..0000000000000000
--- a/arch/arm/mach-shmobile/pm-sh73a0.c
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * sh73a0 Power management support
- *
- * Copyright (C) 2012 Bastian Hecht <hechtb+renesas@gmail.com>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/suspend.h>
-#include "common.h"
-
-#ifdef CONFIG_SUSPEND
-static int sh73a0_enter_suspend(suspend_state_t suspend_state)
-{
- cpu_do_idle();
- return 0;
-}
-
-static void sh73a0_suspend_init(void)
-{
- shmobile_suspend_ops.enter = sh73a0_enter_suspend;
-}
-#else
-static void sh73a0_suspend_init(void) {}
-#endif
-
-void __init sh73a0_pm_init(void)
-{
- sh73a0_suspend_init();
-}
diff --git a/arch/arm/mach-shmobile/setup-sh73a0.c b/arch/arm/mach-shmobile/setup-sh73a0.c
index fb2ab7590af8bf9d..a1e8e72e25b58c3e 100644
--- a/arch/arm/mach-shmobile/setup-sh73a0.c
+++ b/arch/arm/mach-shmobile/setup-sh73a0.c
@@ -18,28 +18,17 @@
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <linux/platform_device.h>
#include <linux/of_platform.h>
#include <linux/delay.h>
#include <linux/input.h>
-#include <linux/i2c/i2c-sh_mobile.h>
#include <linux/io.h>
-#include <linux/serial_sci.h>
-#include <linux/sh_dma.h>
-#include <linux/sh_timer.h>
-#include <linux/platform_data/sh_ipmmu.h>
-#include <linux/platform_data/irq-renesas-intc-irqpin.h>
#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include "common.h"
-#include "dma-register.h"
-#include "intc.h"
-#include "irqs.h"
#include "sh73a0.h"
static struct map_desc sh73a0_io_desc[] __initdata = {
@@ -54,737 +43,12 @@ static struct map_desc sh73a0_io_desc[] __initdata = {
},
};
-void __init sh73a0_map_io(void)
+static void __init sh73a0_map_io(void)
{
debug_ll_io_init();
iotable_init(sh73a0_io_desc, ARRAY_SIZE(sh73a0_io_desc));
}
-/* PFC */
-static struct resource pfc_resources[] __initdata = {
- DEFINE_RES_MEM(0xe6050000, 0x8000),
- DEFINE_RES_MEM(0xe605801c, 0x000c),
-};
-
-void __init sh73a0_pinmux_init(void)
-{
- platform_device_register_simple("pfc-sh73a0", -1, pfc_resources,
- ARRAY_SIZE(pfc_resources));
-}
-
-/* SCIF */
-#define SH73A0_SCIF(scif_type, index, baseaddr, irq) \
-static struct plat_sci_port scif##index##_platform_data = { \
- .type = scif_type, \
- .flags = UPF_BOOT_AUTOCONF, \
- .scscr = SCSCR_RE | SCSCR_TE, \
-}; \
- \
-static struct resource scif##index##_resources[] = { \
- DEFINE_RES_MEM(baseaddr, 0x100), \
- DEFINE_RES_IRQ(irq), \
-}; \
- \
-static struct platform_device scif##index##_device = { \
- .name = "sh-sci", \
- .id = index, \
- .resource = scif##index##_resources, \
- .num_resources = ARRAY_SIZE(scif##index##_resources), \
- .dev = { \
- .platform_data = &scif##index##_platform_data, \
- }, \
-}
-
-SH73A0_SCIF(PORT_SCIFA, 0, 0xe6c40000, gic_spi(72));
-SH73A0_SCIF(PORT_SCIFA, 1, 0xe6c50000, gic_spi(73));
-SH73A0_SCIF(PORT_SCIFA, 2, 0xe6c60000, gic_spi(74));
-SH73A0_SCIF(PORT_SCIFA, 3, 0xe6c70000, gic_spi(75));
-SH73A0_SCIF(PORT_SCIFA, 4, 0xe6c80000, gic_spi(78));
-SH73A0_SCIF(PORT_SCIFA, 5, 0xe6cb0000, gic_spi(79));
-SH73A0_SCIF(PORT_SCIFA, 6, 0xe6cc0000, gic_spi(156));
-SH73A0_SCIF(PORT_SCIFA, 7, 0xe6cd0000, gic_spi(143));
-SH73A0_SCIF(PORT_SCIFB, 8, 0xe6c30000, gic_spi(80));
-
-static struct sh_timer_config cmt1_platform_data = {
- .channels_mask = 0x3f,
-};
-
-static struct resource cmt1_resources[] = {
- DEFINE_RES_MEM(0xe6138000, 0x200),
- DEFINE_RES_IRQ(gic_spi(65)),
-};
-
-static struct platform_device cmt1_device = {
- .name = "sh-cmt-48",
- .id = 1,
- .dev = {
- .platform_data = &cmt1_platform_data,
- },
- .resource = cmt1_resources,
- .num_resources = ARRAY_SIZE(cmt1_resources),
-};
-
-/* TMU */
-static struct sh_timer_config tmu0_platform_data = {
- .channels_mask = 7,
-};
-
-static struct resource tmu0_resources[] = {
- DEFINE_RES_MEM(0xfff60000, 0x2c),
- DEFINE_RES_IRQ(intcs_evt2irq(0xe80)),
- DEFINE_RES_IRQ(intcs_evt2irq(0xea0)),
- DEFINE_RES_IRQ(intcs_evt2irq(0xec0)),
-};
-
-static struct platform_device tmu0_device = {
- .name = "sh-tmu",
- .id = 0,
- .dev = {
- .platform_data = &tmu0_platform_data,
- },
- .resource = tmu0_resources,
- .num_resources = ARRAY_SIZE(tmu0_resources),
-};
-
-static struct resource i2c0_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6820000, 0x426),
- [1] = {
- .start = gic_spi(167),
- .end = gic_spi(170),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6822000, 0x426),
- [1] = {
- .start = gic_spi(51),
- .end = gic_spi(54),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c2_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6824000, 0x426),
- [1] = {
- .start = gic_spi(171),
- .end = gic_spi(174),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c3_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6826000, 0x426),
- [1] = {
- .start = gic_spi(183),
- .end = gic_spi(186),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c4_resources[] = {
- [0] = DEFINE_RES_MEM(0xe6828000, 0x426),
- [1] = {
- .start = gic_spi(187),
- .end = gic_spi(190),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct i2c_sh_mobile_platform_data i2c_platform_data = {
- .clks_per_count = 2,
-};
-
-static struct platform_device i2c0_device = {
- .name = "i2c-sh_mobile",
- .id = 0,
- .resource = i2c0_resources,
- .num_resources = ARRAY_SIZE(i2c0_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c1_device = {
- .name = "i2c-sh_mobile",
- .id = 1,
- .resource = i2c1_resources,
- .num_resources = ARRAY_SIZE(i2c1_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c2_device = {
- .name = "i2c-sh_mobile",
- .id = 2,
- .resource = i2c2_resources,
- .num_resources = ARRAY_SIZE(i2c2_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c3_device = {
- .name = "i2c-sh_mobile",
- .id = 3,
- .resource = i2c3_resources,
- .num_resources = ARRAY_SIZE(i2c3_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static struct platform_device i2c4_device = {
- .name = "i2c-sh_mobile",
- .id = 4,
- .resource = i2c4_resources,
- .num_resources = ARRAY_SIZE(i2c4_resources),
- .dev = {
- .platform_data = &i2c_platform_data,
- },
-};
-
-static const struct sh_dmae_slave_config sh73a0_dmae_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_SCIF0_TX,
- .addr = 0xe6c40020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x21,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF0_RX,
- .addr = 0xe6c40024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x22,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF1_TX,
- .addr = 0xe6c50020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x25,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF1_RX,
- .addr = 0xe6c50024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x26,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF2_TX,
- .addr = 0xe6c60020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x29,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF2_RX,
- .addr = 0xe6c60024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x2a,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF3_TX,
- .addr = 0xe6c70020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x2d,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF3_RX,
- .addr = 0xe6c70024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x2e,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF4_TX,
- .addr = 0xe6c80020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x39,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF4_RX,
- .addr = 0xe6c80024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x3a,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF5_TX,
- .addr = 0xe6cb0020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x35,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF5_RX,
- .addr = 0xe6cb0024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x36,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF6_TX,
- .addr = 0xe6cc0020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x1d,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF6_RX,
- .addr = 0xe6cc0024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x1e,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF7_TX,
- .addr = 0xe6cd0020,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x19,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF7_RX,
- .addr = 0xe6cd0024,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x1a,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF8_TX,
- .addr = 0xe6c30040,
- .chcr = CHCR_TX(XMIT_SZ_8BIT),
- .mid_rid = 0x3d,
- }, {
- .slave_id = SHDMA_SLAVE_SCIF8_RX,
- .addr = 0xe6c30060,
- .chcr = CHCR_RX(XMIT_SZ_8BIT),
- .mid_rid = 0x3e,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI0_TX,
- .addr = 0xee100030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc1,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI0_RX,
- .addr = 0xee100030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xc2,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_TX,
- .addr = 0xee120030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc9,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_RX,
- .addr = 0xee120030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xca,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_TX,
- .addr = 0xee140030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xcd,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_RX,
- .addr = 0xee140030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xce,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_TX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd1,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_RX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xd2,
- },
-};
-
-#define DMAE_CHANNEL(_offset) \
- { \
- .offset = _offset - 0x20, \
- .dmars = _offset - 0x20 + 0x40, \
- }
-
-static const struct sh_dmae_channel sh73a0_dmae_channels[] = {
- DMAE_CHANNEL(0x8000),
- DMAE_CHANNEL(0x8080),
- DMAE_CHANNEL(0x8100),
- DMAE_CHANNEL(0x8180),
- DMAE_CHANNEL(0x8200),
- DMAE_CHANNEL(0x8280),
- DMAE_CHANNEL(0x8300),
- DMAE_CHANNEL(0x8380),
- DMAE_CHANNEL(0x8400),
- DMAE_CHANNEL(0x8480),
- DMAE_CHANNEL(0x8500),
- DMAE_CHANNEL(0x8580),
- DMAE_CHANNEL(0x8600),
- DMAE_CHANNEL(0x8680),
- DMAE_CHANNEL(0x8700),
- DMAE_CHANNEL(0x8780),
- DMAE_CHANNEL(0x8800),
- DMAE_CHANNEL(0x8880),
- DMAE_CHANNEL(0x8900),
- DMAE_CHANNEL(0x8980),
-};
-
-static struct sh_dmae_pdata sh73a0_dmae_platform_data = {
- .slave = sh73a0_dmae_slaves,
- .slave_num = ARRAY_SIZE(sh73a0_dmae_slaves),
- .channel = sh73a0_dmae_channels,
- .channel_num = ARRAY_SIZE(sh73a0_dmae_channels),
- .ts_low_shift = TS_LOW_SHIFT,
- .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
- .ts_high_shift = TS_HI_SHIFT,
- .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
- .ts_shift = dma_ts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
- .dmaor_init = DMAOR_DME,
-};
-
-static struct resource sh73a0_dmae_resources[] = {
- DEFINE_RES_MEM(0xfe000020, 0x89e0),
- {
- .name = "error_irq",
- .start = gic_spi(129),
- .end = gic_spi(129),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-19 */
- .start = gic_spi(109),
- .end = gic_spi(128),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device dma0_device = {
- .name = "sh-dma-engine",
- .id = 0,
- .resource = sh73a0_dmae_resources,
- .num_resources = ARRAY_SIZE(sh73a0_dmae_resources),
- .dev = {
- .platform_data = &sh73a0_dmae_platform_data,
- },
-};
-
-/* MPDMAC */
-static const struct sh_dmae_slave_config sh73a0_mpdma_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_FSI2A_RX,
- .addr = 0xec230020,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xd6, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2A_TX,
- .addr = 0xec230024,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd5, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2C_RX,
- .addr = 0xec230060,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xda, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2C_TX,
- .addr = 0xec230064,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd9, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2B_RX,
- .addr = 0xec240020,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0x8e, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2B_TX,
- .addr = 0xec240024,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0x8d, /* CHECK ME */
- }, {
- .slave_id = SHDMA_SLAVE_FSI2D_RX,
- .addr = 0xec240060,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0x9a, /* CHECK ME */
- },
-};
-
-#define MPDMA_CHANNEL(a, b, c) \
-{ \
- .offset = a, \
- .dmars = b, \
- .dmars_bit = c, \
- .chclr_offset = (0x220 - 0x20) + a \
-}
-
-static const struct sh_dmae_channel sh73a0_mpdma_channels[] = {
- MPDMA_CHANNEL(0x00, 0, 0),
- MPDMA_CHANNEL(0x10, 0, 8),
- MPDMA_CHANNEL(0x20, 4, 0),
- MPDMA_CHANNEL(0x30, 4, 8),
- MPDMA_CHANNEL(0x50, 8, 0),
- MPDMA_CHANNEL(0x70, 8, 8),
-};
-
-static struct sh_dmae_pdata sh73a0_mpdma_platform_data = {
- .slave = sh73a0_mpdma_slaves,
- .slave_num = ARRAY_SIZE(sh73a0_mpdma_slaves),
- .channel = sh73a0_mpdma_channels,
- .channel_num = ARRAY_SIZE(sh73a0_mpdma_channels),
- .ts_low_shift = TS_LOW_SHIFT,
- .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
- .ts_high_shift = TS_HI_SHIFT,
- .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
- .ts_shift = dma_ts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
- .dmaor_init = DMAOR_DME,
- .chclr_present = 1,
-};
-
-/* Resource order important! */
-static struct resource sh73a0_mpdma_resources[] = {
- /* Channel registers and DMAOR */
- DEFINE_RES_MEM(0xec618020, 0x270),
- /* DMARSx */
- DEFINE_RES_MEM(0xec619000, 0xc),
- {
- .name = "error_irq",
- .start = gic_spi(181),
- .end = gic_spi(181),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(175),
- .end = gic_spi(180),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device mpdma0_device = {
- .name = "sh-dma-engine",
- .id = 1,
- .resource = sh73a0_mpdma_resources,
- .num_resources = ARRAY_SIZE(sh73a0_mpdma_resources),
- .dev = {
- .platform_data = &sh73a0_mpdma_platform_data,
- },
-};
-
-static struct resource pmu_resources[] = {
- [0] = {
- .start = gic_spi(55),
- .end = gic_spi(55),
- .flags = IORESOURCE_IRQ,
- },
- [1] = {
- .start = gic_spi(56),
- .end = gic_spi(56),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device pmu_device = {
- .name = "armv7-pmu",
- .id = -1,
- .num_resources = ARRAY_SIZE(pmu_resources),
- .resource = pmu_resources,
-};
-
-/* an IPMMU module for ICB */
-static struct resource ipmmu_resources[] = {
- DEFINE_RES_MEM(0xfe951000, 0x100),
-};
-
-static const char * const ipmmu_dev_names[] = {
- "sh_mobile_lcdc_fb.0",
-};
-
-static struct shmobile_ipmmu_platform_data ipmmu_platform_data = {
- .dev_names = ipmmu_dev_names,
- .num_dev_names = ARRAY_SIZE(ipmmu_dev_names),
-};
-
-static struct platform_device ipmmu_device = {
- .name = "ipmmu",
- .id = -1,
- .dev = {
- .platform_data = &ipmmu_platform_data,
- },
- .resource = ipmmu_resources,
- .num_resources = ARRAY_SIZE(ipmmu_resources),
-};
-
-static struct renesas_intc_irqpin_config irqpin0_platform_data = {
- .irq_base = irq_pin(0), /* IRQ0 -> IRQ7 */
- .control_parent = true,
-};
-
-static struct resource irqpin0_resources[] = {
- DEFINE_RES_MEM(0xe6900000, 4), /* ICR1A */
- DEFINE_RES_MEM(0xe6900010, 4), /* INTPRI00A */
- DEFINE_RES_MEM(0xe6900020, 1), /* INTREQ00A */
- DEFINE_RES_MEM(0xe6900040, 1), /* INTMSK00A */
- DEFINE_RES_MEM(0xe6900060, 1), /* INTMSKCLR00A */
- DEFINE_RES_IRQ(gic_spi(1)), /* IRQ0 */
- DEFINE_RES_IRQ(gic_spi(2)), /* IRQ1 */
- DEFINE_RES_IRQ(gic_spi(3)), /* IRQ2 */
- DEFINE_RES_IRQ(gic_spi(4)), /* IRQ3 */
- DEFINE_RES_IRQ(gic_spi(5)), /* IRQ4 */
- DEFINE_RES_IRQ(gic_spi(6)), /* IRQ5 */
- DEFINE_RES_IRQ(gic_spi(7)), /* IRQ6 */
- DEFINE_RES_IRQ(gic_spi(8)), /* IRQ7 */
-};
-
-static struct platform_device irqpin0_device = {
- .name = "renesas_intc_irqpin",
- .id = 0,
- .resource = irqpin0_resources,
- .num_resources = ARRAY_SIZE(irqpin0_resources),
- .dev = {
- .platform_data = &irqpin0_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin1_platform_data = {
- .irq_base = irq_pin(8), /* IRQ8 -> IRQ15 */
- .control_parent = true, /* Disable spurious IRQ10 */
-};
-
-static struct resource irqpin1_resources[] = {
- DEFINE_RES_MEM(0xe6900004, 4), /* ICR2A */
- DEFINE_RES_MEM(0xe6900014, 4), /* INTPRI10A */
- DEFINE_RES_MEM(0xe6900024, 1), /* INTREQ10A */
- DEFINE_RES_MEM(0xe6900044, 1), /* INTMSK10A */
- DEFINE_RES_MEM(0xe6900064, 1), /* INTMSKCLR10A */
- DEFINE_RES_IRQ(gic_spi(9)), /* IRQ8 */
- DEFINE_RES_IRQ(gic_spi(10)), /* IRQ9 */
- DEFINE_RES_IRQ(gic_spi(11)), /* IRQ10 */
- DEFINE_RES_IRQ(gic_spi(12)), /* IRQ11 */
- DEFINE_RES_IRQ(gic_spi(13)), /* IRQ12 */
- DEFINE_RES_IRQ(gic_spi(14)), /* IRQ13 */
- DEFINE_RES_IRQ(gic_spi(15)), /* IRQ14 */
- DEFINE_RES_IRQ(gic_spi(16)), /* IRQ15 */
-};
-
-static struct platform_device irqpin1_device = {
- .name = "renesas_intc_irqpin",
- .id = 1,
- .resource = irqpin1_resources,
- .num_resources = ARRAY_SIZE(irqpin1_resources),
- .dev = {
- .platform_data = &irqpin1_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin2_platform_data = {
- .irq_base = irq_pin(16), /* IRQ16 -> IRQ23 */
- .control_parent = true,
-};
-
-static struct resource irqpin2_resources[] = {
- DEFINE_RES_MEM(0xe6900008, 4), /* ICR3A */
- DEFINE_RES_MEM(0xe6900018, 4), /* INTPRI20A */
- DEFINE_RES_MEM(0xe6900028, 1), /* INTREQ20A */
- DEFINE_RES_MEM(0xe6900048, 1), /* INTMSK20A */
- DEFINE_RES_MEM(0xe6900068, 1), /* INTMSKCLR20A */
- DEFINE_RES_IRQ(gic_spi(17)), /* IRQ16 */
- DEFINE_RES_IRQ(gic_spi(18)), /* IRQ17 */
- DEFINE_RES_IRQ(gic_spi(19)), /* IRQ18 */
- DEFINE_RES_IRQ(gic_spi(20)), /* IRQ19 */
- DEFINE_RES_IRQ(gic_spi(21)), /* IRQ20 */
- DEFINE_RES_IRQ(gic_spi(22)), /* IRQ21 */
- DEFINE_RES_IRQ(gic_spi(23)), /* IRQ22 */
- DEFINE_RES_IRQ(gic_spi(24)), /* IRQ23 */
-};
-
-static struct platform_device irqpin2_device = {
- .name = "renesas_intc_irqpin",
- .id = 2,
- .resource = irqpin2_resources,
- .num_resources = ARRAY_SIZE(irqpin2_resources),
- .dev = {
- .platform_data = &irqpin2_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin3_platform_data = {
- .irq_base = irq_pin(24), /* IRQ24 -> IRQ31 */
- .control_parent = true,
-};
-
-static struct resource irqpin3_resources[] = {
- DEFINE_RES_MEM(0xe690000c, 4), /* ICR4A */
- DEFINE_RES_MEM(0xe690001c, 4), /* INTPRI30A */
- DEFINE_RES_MEM(0xe690002c, 1), /* INTREQ30A */
- DEFINE_RES_MEM(0xe690004c, 1), /* INTMSK30A */
- DEFINE_RES_MEM(0xe690006c, 1), /* INTMSKCLR30A */
- DEFINE_RES_IRQ(gic_spi(25)), /* IRQ24 */
- DEFINE_RES_IRQ(gic_spi(26)), /* IRQ25 */
- DEFINE_RES_IRQ(gic_spi(27)), /* IRQ26 */
- DEFINE_RES_IRQ(gic_spi(28)), /* IRQ27 */
- DEFINE_RES_IRQ(gic_spi(29)), /* IRQ28 */
- DEFINE_RES_IRQ(gic_spi(30)), /* IRQ29 */
- DEFINE_RES_IRQ(gic_spi(31)), /* IRQ30 */
- DEFINE_RES_IRQ(gic_spi(32)), /* IRQ31 */
-};
-
-static struct platform_device irqpin3_device = {
- .name = "renesas_intc_irqpin",
- .id = 3,
- .resource = irqpin3_resources,
- .num_resources = ARRAY_SIZE(irqpin3_resources),
- .dev = {
- .platform_data = &irqpin3_platform_data,
- },
-};
-
-static struct platform_device *sh73a0_early_devices[] __initdata = {
- &scif0_device,
- &scif1_device,
- &scif2_device,
- &scif3_device,
- &scif4_device,
- &scif5_device,
- &scif6_device,
- &scif7_device,
- &scif8_device,
- &tmu0_device,
- &ipmmu_device,
- &cmt1_device,
-};
-
-static struct platform_device *sh73a0_late_devices[] __initdata = {
- &i2c0_device,
- &i2c1_device,
- &i2c2_device,
- &i2c3_device,
- &i2c4_device,
- &dma0_device,
- &mpdma0_device,
- &pmu_device,
- &irqpin0_device,
- &irqpin1_device,
- &irqpin2_device,
- &irqpin3_device,
-};
-
-#define SRCR2 IOMEM(0xe61580b0)
-
-void __init sh73a0_add_standard_devices(void)
-{
- /* Clear software reset bit on SY-DMAC module */
- __raw_writel(__raw_readl(SRCR2) & ~(1 << 18), SRCR2);
-
- platform_add_devices(sh73a0_early_devices,
- ARRAY_SIZE(sh73a0_early_devices));
- platform_add_devices(sh73a0_late_devices,
- ARRAY_SIZE(sh73a0_late_devices));
-}
-
-/* do nothing for !CONFIG_SMP or !CONFIG_HAVE_TWD */
-void __init __weak sh73a0_register_twd(void) { }
-
-void __init sh73a0_earlytimer_init(void)
-{
- shmobile_init_delay();
-#ifndef CONFIG_COMMON_CLK
- sh73a0_clock_init();
-#endif
- shmobile_earlytimer_init();
- sh73a0_register_twd();
-}
-
-void __init sh73a0_add_early_devices(void)
-{
- early_platform_add_devices(sh73a0_early_devices,
- ARRAY_SIZE(sh73a0_early_devices));
-
- /* setup early console here as well */
- shmobile_setup_console();
-}
-
-#ifdef CONFIG_USE_OF
-
static void __init sh73a0_generic_init(void)
{
#ifdef CONFIG_CACHE_L2X0
@@ -807,4 +71,3 @@ DT_MACHINE_START(SH73A0_DT, "Generic SH73A0 (Flattened Device Tree)")
.init_late = shmobile_init_late,
.dt_compat = sh73a0_boards_compat_dt,
MACHINE_END
-#endif /* CONFIG_USE_OF */
diff --git a/arch/arm/mach-shmobile/sh73a0.h b/arch/arm/mach-shmobile/sh73a0.h
index 5a80f18b4fa0665f..39646806cf64646b 100644
--- a/arch/arm/mach-shmobile/sh73a0.h
+++ b/arch/arm/mach-shmobile/sh73a0.h
@@ -1,89 +1,6 @@
#ifndef __ASM_SH73A0_H__
#define __ASM_SH73A0_H__
-/* DMA slave IDs */
-enum {
- SHDMA_SLAVE_INVALID,
- SHDMA_SLAVE_SCIF0_TX,
- SHDMA_SLAVE_SCIF0_RX,
- SHDMA_SLAVE_SCIF1_TX,
- SHDMA_SLAVE_SCIF1_RX,
- SHDMA_SLAVE_SCIF2_TX,
- SHDMA_SLAVE_SCIF2_RX,
- SHDMA_SLAVE_SCIF3_TX,
- SHDMA_SLAVE_SCIF3_RX,
- SHDMA_SLAVE_SCIF4_TX,
- SHDMA_SLAVE_SCIF4_RX,
- SHDMA_SLAVE_SCIF5_TX,
- SHDMA_SLAVE_SCIF5_RX,
- SHDMA_SLAVE_SCIF6_TX,
- SHDMA_SLAVE_SCIF6_RX,
- SHDMA_SLAVE_SCIF7_TX,
- SHDMA_SLAVE_SCIF7_RX,
- SHDMA_SLAVE_SCIF8_TX,
- SHDMA_SLAVE_SCIF8_RX,
- SHDMA_SLAVE_SDHI0_TX,
- SHDMA_SLAVE_SDHI0_RX,
- SHDMA_SLAVE_SDHI1_TX,
- SHDMA_SLAVE_SDHI1_RX,
- SHDMA_SLAVE_SDHI2_TX,
- SHDMA_SLAVE_SDHI2_RX,
- SHDMA_SLAVE_MMCIF_TX,
- SHDMA_SLAVE_MMCIF_RX,
- SHDMA_SLAVE_FSI2A_TX,
- SHDMA_SLAVE_FSI2A_RX,
- SHDMA_SLAVE_FSI2B_TX,
- SHDMA_SLAVE_FSI2B_RX,
- SHDMA_SLAVE_FSI2C_TX,
- SHDMA_SLAVE_FSI2C_RX,
- SHDMA_SLAVE_FSI2D_RX,
-};
-
-/*
- * SH73A0 IRQ LOCATION TABLE
- *
- * 416 -----------------------------------------
- * IRQ0-IRQ15
- * 431 -----------------------------------------
- * ...
- * 448 -----------------------------------------
- * sh73a0-intcs
- * sh73a0-intca-irq-pins
- * 680 -----------------------------------------
- * ...
- * 700 -----------------------------------------
- * sh73a0-pint0
- * 731 -----------------------------------------
- * 732 -----------------------------------------
- * sh73a0-pint1
- * 739 -----------------------------------------
- * ...
- * 800 -----------------------------------------
- * IRQ16-IRQ31
- * 815 -----------------------------------------
- * ...
- * 928 -----------------------------------------
- * sh73a0-intca-irq-pins
- * 943 -----------------------------------------
- */
-
-/* PINT interrupts are located@Linux IRQ 700 and up */
-#define SH73A0_PINT0_IRQ(irq) ((irq) + 700)
-#define SH73A0_PINT1_IRQ(irq) ((irq) + 732)
-
-extern void sh73a0_init_irq(void);
-extern void sh73a0_init_irq_dt(void);
-extern void sh73a0_map_io(void);
-extern void sh73a0_earlytimer_init(void);
-extern void sh73a0_add_early_devices(void);
-extern void sh73a0_add_standard_devices(void);
-extern void sh73a0_clock_init(void);
-extern void sh73a0_pinmux_init(void);
-extern void sh73a0_pm_init(void);
-extern struct clk sh73a0_extal1_clk;
-extern struct clk sh73a0_extal2_clk;
-extern struct clk sh73a0_extcki_clk;
-extern struct clk sh73a0_extalr_clk;
extern struct smp_operations sh73a0_smp_ops;
#endif /* __ASM_SH73A0_H__ */
diff --git a/arch/arm/mach-shmobile/smp-sh73a0.c b/arch/arm/mach-shmobile/smp-sh73a0.c
index 2106d6b76a069392..d03aa11fb46dad19 100644
--- a/arch/arm/mach-shmobile/smp-sh73a0.c
+++ b/arch/arm/mach-shmobile/smp-sh73a0.c
@@ -33,14 +33,6 @@
#define SH73A0_SCU_BASE 0xf0000000
-#if defined(CONFIG_HAVE_ARM_TWD) && !defined(CONFIG_ARCH_MULTIPLATFORM)
-static DEFINE_TWD_LOCAL_TIMER(twd_local_timer, SH73A0_SCU_BASE + 0x600, 29);
-void __init sh73a0_register_twd(void)
-{
- twd_local_timer_register(&twd_local_timer);
-}
-#endif
-
static int sh73a0_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned int lcpu = cpu_logical_map(cpu);
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 05/15] ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The Armadillo-800 EVA board is sufficiently supported by DT-based and
board-less R-Mobile A1 (r8a7740) multiplatform kernels, and board
staging code. Hence remove the legacy board code to reduce maintenance
effort.
Lacking areas are:
- USB (it doesn't work in legacy, neither),
- HDMI (it doesn't work in legacy, neither),
- Camera (we don't care),
- DMAC/IPMMU (no DT bindings are planned).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 9 -
arch/arm/mach-shmobile/Makefile | 1 -
arch/arm/mach-shmobile/Makefile.boot | 1 -
arch/arm/mach-shmobile/board-armadillo800eva.c | 1365 ------------------------
4 files changed, 1376 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/board-armadillo800eva.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index bc8e2f60fe505ee2..e256c6b664710099 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -129,15 +129,6 @@ config ARCH_R8A7779
comment "Renesas ARM SoCs Board Type"
-config MACH_ARMADILLO800EVA
- bool "Armadillo-800 EVA board"
- depends on ARCH_R8A7740
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select SMSC_PHY if SH_ETH
- select SND_SOC_WM8978 if SND_SIMPLE_CARD && I2C
- select USE_OF
-
config MACH_BOCKW
bool "BOCK-W platform"
depends on ARCH_R8A7778
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 7e20ab3021be0ff2..4ffd7428353b53f9 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -58,7 +58,6 @@ else
obj-$(CONFIG_MACH_BOCKW) += board-bockw.o
obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
-obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
endif
# Framework support
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index 2269b1c3c30b108a..14cdfc0ed0755a59 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -1,6 +1,5 @@
# per-board load address for uImage
loadaddr-y :-loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000
loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
deleted file mode 100644
index bf37e3c532f661a6..0000000000000000
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ /dev/null
@@ -1,1365 +0,0 @@
-/*
- * armadillo 800 eva board support
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/i2c-gpio.h>
-#include <linux/input.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/mfd/tmio.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mmc/sh_mobile_sdhi.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/platform_data/st1232_pdata.h>
-#include <linux/platform_device.h>
-#include <linux/pwm.h>
-#include <linux/pwm_backlight.h>
-#include <linux/reboot.h>
-#include <linux/regulator/driver.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/gpio-regulator.h>
-#include <linux/regulator/machine.h>
-#include <linux/sh_eth.h>
-#include <linux/usb/renesas_usbhs.h>
-#include <linux/videodev2.h>
-
-#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/page.h>
-#include <media/mt9t112.h>
-#include <media/sh_mobile_ceu.h>
-#include <media/soc_camera.h>
-#include <sound/sh_fsi.h>
-#include <sound/simple_card.h>
-#include <video/sh_mobile_hdmi.h>
-#include <video/sh_mobile_lcdc.h>
-
-#include "common.h"
-#include "irqs.h"
-#include "pm-rmobile.h"
-#include "r8a7740.h"
-#include "sh-gpio.h"
-
-/*
- * CON1 Camera Module
- * CON2 Extension Bus
- * CON3 HDMI Output
- * CON4 Composite Video Output
- * CON5 H-UDI JTAG
- * CON6 ARM JTAG
- * CON7 SD1
- * CON8 SD2
- * CON9 RTC BackUp
- * CON10 Monaural Mic Input
- * CON11 Stereo Headphone Output
- * CON12 Audio Line Output(L)
- * CON13 Audio Line Output(R)
- * CON14 AWL13 Module
- * CON15 Extension
- * CON16 LCD1
- * CON17 LCD2
- * CON19 Power Input
- * CON20 USB1
- * CON21 USB2
- * CON22 Serial
- * CON23 LAN
- * CON24 USB3
- * LED1 Camera LED(Yellow)
- * LED2 Power LED (Green)
- * ED3-LED6 User LED(Yellow)
- * LED7 LAN link LED(Green)
- * LED8 LAN activity LED(Yellow)
- */
-
-/*
- * DipSwitch
- *
- * SW1
- *
- * -12345678-+---------------+----------------------------
- * 1 | boot | hermit
- * 0 | boot | OS auto boot
- * -12345678-+---------------+----------------------------
- * 00 | boot device | eMMC
- * 10 | boot device | SDHI0 (CON7)
- * 01 | boot device | -
- * 11 | boot device | Extension Buss (CS0)
- * -12345678-+---------------+----------------------------
- * 0 | Extension Bus | D8-D15 disable, eMMC enable
- * 1 | Extension Bus | D8-D15 enable, eMMC disable
- * -12345678-+---------------+----------------------------
- * 0 | SDHI1 | COM8 disable, COM14 enable
- * 1 | SDHI1 | COM8 enable, COM14 disable
- * -12345678-+---------------+----------------------------
- * 0 | USB0 | COM20 enable, COM24 disable
- * 1 | USB0 | COM20 disable, COM24 enable
- * -12345678-+---------------+----------------------------
- * 00 | JTAG | SH-X2
- * 10 | JTAG | ARM
- * 01 | JTAG | -
- * 11 | JTAG | Boundary Scan
- *-----------+---------------+----------------------------
- */
-
-/*
- * FSI-WM8978
- *
- * this command is required when playback.
- *
- * # amixer set "Headphone" 50
- *
- * this command is required when capture.
- *
- * # amixer set "Input PGA" 15
- * # amixer set "Left Input Mixer MicP" on
- * # amixer set "Left Input Mixer MicN" on
- * # amixer set "Right Input Mixer MicN" on
- * # amixer set "Right Input Mixer MicP" on
- */
-
-/*
- * USB function
- *
- * When you use USB Function,
- * set SW1.6 ON, and connect cable to CN24.
- *
- * USBF needs workaround on R8A7740 chip.
- * These are a little bit complex.
- * see
- * usbhsf_power_ctrl()
- */
-#define IRQ7 irq_pin(7)
-#define USBCR1 IOMEM(0xe605810a)
-#define USBH 0xC6700000
-#define USBH_USBCTR 0x10834
-
-struct usbhsf_private {
- struct clk *phy;
- struct clk *usb24;
- struct clk *pci;
- struct clk *func;
- struct clk *host;
- void __iomem *usbh_base;
- struct renesas_usbhs_platform_info info;
-};
-
-#define usbhsf_get_priv(pdev) \
- container_of(renesas_usbhs_get_info(pdev), \
- struct usbhsf_private, info)
-
-static int usbhsf_get_id(struct platform_device *pdev)
-{
- return USBHS_GADGET;
-}
-
-static int usbhsf_power_ctrl(struct platform_device *pdev,
- void __iomem *base, int enable)
-{
- struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-
- /*
- * Work around for USB Function.
- * It needs USB host clock, and settings
- */
- if (enable) {
- /*
- * enable all the related usb clocks
- * for usb workaround
- */
- clk_enable(priv->usb24);
- clk_enable(priv->pci);
- clk_enable(priv->host);
- clk_enable(priv->func);
- clk_enable(priv->phy);
-
- /*
- * set USBCR1
- *
- * Port1 is driven by USB function,
- * Port2 is driven by USB HOST
- * One HOST (Port1 or Port2 is HOST)
- * USB PLL input clock = 24MHz
- */
- __raw_writew(0xd750, USBCR1);
- mdelay(1);
-
- /*
- * start USB Host
- */
- __raw_writel(0x0000000c, priv->usbh_base + USBH_USBCTR);
- __raw_writel(0x00000008, priv->usbh_base + USBH_USBCTR);
- mdelay(10);
-
- /*
- * USB PHY Power ON
- */
- __raw_writew(0xd770, USBCR1);
- __raw_writew(0x4000, base + 0x102); /* USBF :: SUSPMODE */
-
- } else {
- __raw_writel(0x0000010f, priv->usbh_base + USBH_USBCTR);
- __raw_writew(0xd7c0, USBCR1); /* GPIO */
-
- clk_disable(priv->phy);
- clk_disable(priv->func); /* usb work around */
- clk_disable(priv->host); /* usb work around */
- clk_disable(priv->pci); /* usb work around */
- clk_disable(priv->usb24); /* usb work around */
- }
-
- return 0;
-}
-
-static int usbhsf_get_vbus(struct platform_device *pdev)
-{
- return gpio_get_value(209);
-}
-
-static irqreturn_t usbhsf_interrupt(int irq, void *data)
-{
- struct platform_device *pdev = data;
-
- renesas_usbhs_call_notify_hotplug(pdev);
-
- return IRQ_HANDLED;
-}
-
-static int usbhsf_hardware_exit(struct platform_device *pdev)
-{
- struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-
- if (!IS_ERR(priv->phy))
- clk_put(priv->phy);
- if (!IS_ERR(priv->usb24))
- clk_put(priv->usb24);
- if (!IS_ERR(priv->pci))
- clk_put(priv->pci);
- if (!IS_ERR(priv->host))
- clk_put(priv->host);
- if (!IS_ERR(priv->func))
- clk_put(priv->func);
- if (priv->usbh_base)
- iounmap(priv->usbh_base);
-
- priv->phy = NULL;
- priv->usb24 = NULL;
- priv->pci = NULL;
- priv->host = NULL;
- priv->func = NULL;
- priv->usbh_base = NULL;
-
- free_irq(IRQ7, pdev);
-
- return 0;
-}
-
-static int usbhsf_hardware_init(struct platform_device *pdev)
-{
- struct usbhsf_private *priv = usbhsf_get_priv(pdev);
- int ret;
-
- priv->phy = clk_get(&pdev->dev, "phy");
- priv->usb24 = clk_get(&pdev->dev, "usb24");
- priv->pci = clk_get(&pdev->dev, "pci");
- priv->func = clk_get(&pdev->dev, "func");
- priv->host = clk_get(&pdev->dev, "host");
- priv->usbh_base = ioremap_nocache(USBH, 0x20000);
-
- if (IS_ERR(priv->phy) ||
- IS_ERR(priv->usb24) ||
- IS_ERR(priv->pci) ||
- IS_ERR(priv->host) ||
- IS_ERR(priv->func) ||
- !priv->usbh_base) {
- dev_err(&pdev->dev, "USB clock setting failed\n");
- usbhsf_hardware_exit(pdev);
- return -EIO;
- }
-
- ret = request_irq(IRQ7, usbhsf_interrupt, IRQF_TRIGGER_NONE,
- dev_name(&pdev->dev), pdev);
- if (ret) {
- dev_err(&pdev->dev, "request_irq err\n");
- return ret;
- }
- irq_set_irq_type(IRQ7, IRQ_TYPE_EDGE_BOTH);
-
- /* usb24 use 1/1 of parent clock (= usb24s = 24MHz) */
- clk_set_rate(priv->usb24,
- clk_get_rate(clk_get_parent(priv->usb24)));
-
- return 0;
-}
-
-static struct usbhsf_private usbhsf_private = {
- .info = {
- .platform_callback = {
- .get_id = usbhsf_get_id,
- .get_vbus = usbhsf_get_vbus,
- .hardware_init = usbhsf_hardware_init,
- .hardware_exit = usbhsf_hardware_exit,
- .power_ctrl = usbhsf_power_ctrl,
- },
- .driver_param = {
- .buswait_bwait = 5,
- .detection_delay = 5,
- .d0_rx_id = SHDMA_SLAVE_USBHS_RX,
- .d1_tx_id = SHDMA_SLAVE_USBHS_TX,
- },
- }
-};
-
-static struct resource usbhsf_resources[] = {
- {
- .name = "USBHS",
- .start = 0xe6890000,
- .end = 0xe6890104 - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = gic_spi(51),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usbhsf_device = {
- .name = "renesas_usbhs",
- .dev = {
- .platform_data = &usbhsf_private.info,
- },
- .id = -1,
- .num_resources = ARRAY_SIZE(usbhsf_resources),
- .resource = usbhsf_resources,
-};
-
-/* Ether */
-static struct sh_eth_plat_data sh_eth_platdata = {
- .phy = 0x00, /* LAN8710A */
- .edmac_endian = EDMAC_LITTLE_ENDIAN,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource sh_eth_resources[] = {
- {
- .start = 0xe9a00000,
- .end = 0xe9a00800 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0xe9a01800,
- .end = 0xe9a02000 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = gic_spi(110),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sh_eth_device = {
- .name = "r8a7740-gether",
- .id = -1,
- .dev = {
- .platform_data = &sh_eth_platdata,
- .dma_mask = &sh_eth_device.dev.coherent_dma_mask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = sh_eth_resources,
- .num_resources = ARRAY_SIZE(sh_eth_resources),
-};
-
-/* PWM */
-static struct resource pwm_resources[] = {
- [0] = {
- .start = 0xe6600000,
- .end = 0xe66000ff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device pwm_device = {
- .name = "renesas-tpu-pwm",
- .id = -1,
- .num_resources = ARRAY_SIZE(pwm_resources),
- .resource = pwm_resources,
-};
-
-static struct pwm_lookup pwm_lookup[] = {
- PWM_LOOKUP("renesas-tpu-pwm", 2, "pwm-backlight.0", NULL,
- 33333, PWM_POLARITY_INVERSED),
-};
-
-/* LCDC and backlight */
-static struct platform_pwm_backlight_data pwm_backlight_data = {
- .lth_brightness = 50,
- .max_brightness = 255,
- .dft_brightness = 255,
- .pwm_period_ns = 33333, /* 30kHz */
- .enable_gpio = 61,
-};
-
-static struct platform_device pwm_backlight_device = {
- .name = "pwm-backlight",
- .dev = {
- .platform_data = &pwm_backlight_data,
- },
-};
-
-static struct fb_videomode lcdc0_mode = {
- .name = "AMPIER/AM-800480",
- .xres = 800,
- .yres = 480,
- .left_margin = 88,
- .right_margin = 40,
- .hsync_len = 128,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .sync = 0,
-};
-
-static struct sh_mobile_lcdc_info lcdc0_info = {
- .clock_source = LCDC_CLK_BUS,
- .ch[0] = {
- .chan = LCDC_CHAN_MAINLCD,
- .fourcc = V4L2_PIX_FMT_RGB565,
- .interface_type = RGB24,
- .clock_divider = 5,
- .flags = 0,
- .lcd_modes = &lcdc0_mode,
- .num_modes = 1,
- .panel_cfg = {
- .width = 111,
- .height = 68,
- },
- },
-};
-
-static struct resource lcdc0_resources[] = {
- [0] = {
- .name = "LCD0",
- .start = 0xfe940000,
- .end = 0xfe943fff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(177),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device lcdc0_device = {
- .name = "sh_mobile_lcdc_fb",
- .num_resources = ARRAY_SIZE(lcdc0_resources),
- .resource = lcdc0_resources,
- .id = 0,
- .dev = {
- .platform_data = &lcdc0_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-/*
- * LCDC1/HDMI
- */
-static struct sh_mobile_hdmi_info hdmi_info = {
- .flags = HDMI_OUTPUT_PUSH_PULL |
- HDMI_OUTPUT_POLARITY_HI |
- HDMI_32BIT_REG |
- HDMI_HAS_HTOP1 |
- HDMI_SND_SRC_SPDIF,
-};
-
-static struct resource hdmi_resources[] = {
- [0] = {
- .name = "HDMI",
- .start = 0xe6be0000,
- .end = 0xe6be03ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(131),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .name = "HDMI emma3pf",
- .start = 0xe6be4000,
- .end = 0xe6be43ff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device hdmi_device = {
- .name = "sh-mobile-hdmi",
- .num_resources = ARRAY_SIZE(hdmi_resources),
- .resource = hdmi_resources,
- .id = -1,
- .dev = {
- .platform_data = &hdmi_info,
- },
-};
-
-static const struct fb_videomode lcdc1_mode = {
- .name = "HDMI 720p",
- .xres = 1280,
- .yres = 720,
- .pixclock = 13468,
- .left_margin = 220,
- .right_margin = 110,
- .hsync_len = 40,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .refresh = 60,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
-};
-
-static struct sh_mobile_lcdc_info hdmi_lcdc_info = {
- .clock_source = LCDC_CLK_PERIPHERAL, /* HDMI clock */
- .ch[0] = {
- .chan = LCDC_CHAN_MAINLCD,
- .fourcc = V4L2_PIX_FMT_RGB565,
- .interface_type = RGB24,
- .clock_divider = 1,
- .flags = LCDC_FLAGS_DWPOL,
- .lcd_modes = &lcdc1_mode,
- .num_modes = 1,
- .tx_dev = &hdmi_device,
- .panel_cfg = {
- .width = 1280,
- .height = 720,
- },
- },
-};
-
-static struct resource hdmi_lcdc_resources[] = {
- [0] = {
- .name = "LCDC1",
- .start = 0xfe944000,
- .end = 0xfe948000 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(178),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device hdmi_lcdc_device = {
- .name = "sh_mobile_lcdc_fb",
- .num_resources = ARRAY_SIZE(hdmi_lcdc_resources),
- .resource = hdmi_lcdc_resources,
- .id = 1,
- .dev = {
- .platform_data = &hdmi_lcdc_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-/* LEDS */
-static struct gpio_led gpio_leds[] = {
- {
- .name = "LED3",
- .gpio = 102,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- }, {
- .name = "LED4",
- .gpio = 111,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- }, {
- .name = "LED5",
- .gpio = 110,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- }, {
- .name = "LED6",
- .gpio = 177,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- },
-};
-
-static struct gpio_led_platform_data leds_gpio_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &leds_gpio_info,
- },
-};
-
-/* GPIO KEY */
-#define GPIO_KEY(c, g, d, ...) \
- { .code = c, .gpio = g, .desc = d, .active_low = 1, __VA_ARGS__ }
-
-static struct gpio_keys_button gpio_buttons[] = {
- GPIO_KEY(KEY_POWER, 99, "SW3", .wakeup = 1),
- GPIO_KEY(KEY_BACK, 100, "SW4"),
- GPIO_KEY(KEY_MENU, 97, "SW5"),
- GPIO_KEY(KEY_HOME, 98, "SW6"),
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device gpio_keys_device = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-/* Fixed 3.3V regulator to be used by SDHI1, MMCIF */
-static struct regulator_consumer_supply fixed3v3_power_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
- REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
-};
-
-/* Fixed 3.3V regulator used by LCD backlight */
-static struct regulator_consumer_supply fixed5v0_power_consumers[] = {
- REGULATOR_SUPPLY("power", "pwm-backlight.0"),
-};
-
-/* Fixed 3.3V regulator to be used by SDHI0 */
-static struct regulator_consumer_supply vcc_sdhi0_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vcc_sdhi0_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
- .consumer_supplies = vcc_sdhi0_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi0_info = {
- .supply_name = "SDHI0 Vcc",
- .microvolts = 3300000,
- .gpio = 75,
- .enable_high = 1,
- .init_data = &vcc_sdhi0_init_data,
-};
-
-static struct platform_device vcc_sdhi0 = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &vcc_sdhi0_info,
- },
-};
-
-/* 1.8 / 3.3V SDHI0 VccQ regulator */
-static struct regulator_consumer_supply vccq_sdhi0_consumers[] = {
- REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vccq_sdhi0_init_data = {
- .constraints = {
- .input_uV = 3300000,
- .min_uV = 1800000,
- .max_uV = 3300000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vccq_sdhi0_consumers),
- .consumer_supplies = vccq_sdhi0_consumers,
-};
-
-static struct gpio vccq_sdhi0_gpios[] = {
- {17, GPIOF_OUT_INIT_LOW, "vccq-sdhi0" },
-};
-
-static struct gpio_regulator_state vccq_sdhi0_states[] = {
- { .value = 3300000, .gpios = (0 << 0) },
- { .value = 1800000, .gpios = (1 << 0) },
-};
-
-static struct gpio_regulator_config vccq_sdhi0_info = {
- .supply_name = "vqmmc",
-
- .enable_gpio = 74,
- .enable_high = 1,
- .enabled_at_boot = 0,
-
- .gpios = vccq_sdhi0_gpios,
- .nr_gpios = ARRAY_SIZE(vccq_sdhi0_gpios),
-
- .states = vccq_sdhi0_states,
- .nr_states = ARRAY_SIZE(vccq_sdhi0_states),
-
- .type = REGULATOR_VOLTAGE,
- .init_data = &vccq_sdhi0_init_data,
-};
-
-static struct platform_device vccq_sdhi0 = {
- .name = "gpio-regulator",
- .id = -1,
- .dev = {
- .platform_data = &vccq_sdhi0_info,
- },
-};
-
-/* Fixed 3.3V regulator to be used by SDHI1 */
-static struct regulator_consumer_supply vcc_sdhi1_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
-};
-
-static struct regulator_init_data vcc_sdhi1_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi1_consumers),
- .consumer_supplies = vcc_sdhi1_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi1_info = {
- .supply_name = "SDHI1 Vcc",
- .microvolts = 3300000,
- .gpio = 16,
- .enable_high = 1,
- .init_data = &vcc_sdhi1_init_data,
-};
-
-static struct platform_device vcc_sdhi1 = {
- .name = "reg-fixed-voltage",
- .id = 2,
- .dev = {
- .platform_data = &vcc_sdhi1_info,
- },
-};
-
-/* SDHI0 */
-static struct tmio_mmc_data sdhi0_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI0_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI0_RX,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
- MMC_CAP_POWER_OFF_CARD,
- .flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
- .cd_gpio = 167,
-};
-
-static struct resource sdhi0_resources[] = {
- {
- .name = "SDHI0",
- .start = 0xe6850000,
- .end = 0xe6850100 - 1,
- .flags = IORESOURCE_MEM,
- },
- /*
- * no SH_MOBILE_SDHI_IRQ_CARD_DETECT here
- */
- {
- .name = SH_MOBILE_SDHI_IRQ_SDCARD,
- .start = gic_spi(118),
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = SH_MOBILE_SDHI_IRQ_SDIO,
- .start = gic_spi(119),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi0_device = {
- .name = "sh_mobile_sdhi",
- .id = 0,
- .dev = {
- .platform_data = &sdhi0_info,
- },
- .num_resources = ARRAY_SIZE(sdhi0_resources),
- .resource = sdhi0_resources,
-};
-
-/* SDHI1 */
-static struct tmio_mmc_data sdhi1_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI1_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI1_RX,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
- MMC_CAP_POWER_OFF_CARD,
- .flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
- /* Port72 cannot generate IRQs, will be used in polling mode. */
- .cd_gpio = 72,
-};
-
-static struct resource sdhi1_resources[] = {
- [0] = {
- .name = "SDHI1",
- .start = 0xe6860000,
- .end = 0xe6860100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(121),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = gic_spi(122),
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .start = gic_spi(123),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi1_device = {
- .name = "sh_mobile_sdhi",
- .id = 1,
- .dev = {
- .platform_data = &sdhi1_info,
- },
- .num_resources = ARRAY_SIZE(sdhi1_resources),
- .resource = sdhi1_resources,
-};
-
-static const struct pinctrl_map eva_sdhi1_pinctrl_map[] = {
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_data4", "sdhi1"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_ctrl", "sdhi1"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_cd", "sdhi1"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_wp", "sdhi1"),
-};
-
-/* MMCIF */
-static struct sh_mmcif_plat_data sh_mmcif_plat = {
- .sup_pclk = 0,
- .caps = MMC_CAP_4_BIT_DATA |
- MMC_CAP_8_BIT_DATA |
- MMC_CAP_NONREMOVABLE,
- .ccs_unsupported = true,
- .slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
- .slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
-};
-
-static struct resource sh_mmcif_resources[] = {
- [0] = {
- .name = "MMCIF",
- .start = 0xe6bd0000,
- .end = 0xe6bd0100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- /* MMC ERR */
- .start = gic_spi(56),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- /* MMC NOR */
- .start = gic_spi(57),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sh_mmcif_device = {
- .name = "sh_mmcif",
- .id = -1,
- .dev = {
- .platform_data = &sh_mmcif_plat,
- },
- .num_resources = ARRAY_SIZE(sh_mmcif_resources),
- .resource = sh_mmcif_resources,
-};
-
-/* Camera */
-static int mt9t111_power(struct device *dev, int mode)
-{
- struct clk *mclk = clk_get(NULL, "video1");
-
- if (IS_ERR(mclk)) {
- dev_err(dev, "can't get video1 clock\n");
- return -EINVAL;
- }
-
- if (mode) {
- /* video1 (= CON1 camera) expect 24MHz */
- clk_set_rate(mclk, clk_round_rate(mclk, 24000000));
- clk_enable(mclk);
- gpio_set_value(158, 1);
- } else {
- gpio_set_value(158, 0);
- clk_disable(mclk);
- }
-
- clk_put(mclk);
-
- return 0;
-}
-
-static struct i2c_board_info i2c_camera_mt9t111 = {
- I2C_BOARD_INFO("mt9t112", 0x3d),
-};
-
-static struct mt9t112_camera_info mt9t111_info = {
- .divider = { 16, 0, 0, 7, 0, 10, 14, 7, 7 },
-};
-
-static struct soc_camera_link mt9t111_link = {
- .i2c_adapter_id = 0,
- .bus_id = 0,
- .board_info = &i2c_camera_mt9t111,
- .power = mt9t111_power,
- .priv = &mt9t111_info,
-};
-
-static struct platform_device camera_device = {
- .name = "soc-camera-pdrv",
- .id = 0,
- .dev = {
- .platform_data = &mt9t111_link,
- },
-};
-
-/* CEU0 */
-static struct sh_mobile_ceu_info sh_mobile_ceu0_info = {
- .flags = SH_CEU_FLAG_LOWER_8BIT,
-};
-
-static struct resource ceu0_resources[] = {
- [0] = {
- .name = "CEU",
- .start = 0xfe910000,
- .end = 0xfe91009f,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(160),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- /* place holder for contiguous memory */
- },
-};
-
-static struct platform_device ceu0_device = {
- .name = "sh_mobile_ceu",
- .id = 0,
- .num_resources = ARRAY_SIZE(ceu0_resources),
- .resource = ceu0_resources,
- .dev = {
- .platform_data = &sh_mobile_ceu0_info,
- .coherent_dma_mask = 0xffffffff,
- },
-};
-
-/* FSI */
-static struct sh_fsi_platform_info fsi_info = {
- /* FSI-WM8978 */
- .port_a = {
- .tx_id = SHDMA_SLAVE_FSIA_TX,
- },
- /* FSI-HDMI */
- .port_b = {
- .flags = SH_FSI_FMT_SPDIF |
- SH_FSI_ENABLE_STREAM_MODE |
- SH_FSI_CLK_CPG,
- .tx_id = SHDMA_SLAVE_FSIB_TX,
- }
-};
-
-static struct resource fsi_resources[] = {
- [0] = {
- .name = "FSI",
- .start = 0xfe1f0000,
- .end = 0xfe1f0400 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(9),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device fsi_device = {
- .name = "sh_fsi2",
- .id = -1,
- .num_resources = ARRAY_SIZE(fsi_resources),
- .resource = fsi_resources,
- .dev = {
- .platform_data = &fsi_info,
- },
-};
-
-/* FSI-WM8978 */
-static struct asoc_simple_card_info fsi_wm8978_info = {
- .name = "wm8978",
- .card = "FSI2A-WM8978",
- .codec = "wm8978.0-001a",
- .platform = "sh_fsi2",
- .daifmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
- .cpu_dai = {
- .name = "fsia-dai",
- },
- .codec_dai = {
- .name = "wm8978-hifi",
- .sysclk = 12288000,
- },
-};
-
-static struct platform_device fsi_wm8978_device = {
- .name = "asoc-simple-card",
- .id = 0,
- .dev = {
- .platform_data = &fsi_wm8978_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .dma_mask = &fsi_wm8978_device.dev.coherent_dma_mask,
- },
-};
-
-/* FSI-HDMI */
-static struct asoc_simple_card_info fsi2_hdmi_info = {
- .name = "HDMI",
- .card = "FSI2B-HDMI",
- .codec = "sh-mobile-hdmi",
- .platform = "sh_fsi2",
- .daifmt = SND_SOC_DAIFMT_CBS_CFS,
- .cpu_dai = {
- .name = "fsib-dai",
- },
- .codec_dai = {
- .name = "sh_mobile_hdmi-hifi",
- },
-};
-
-static struct platform_device fsi_hdmi_device = {
- .name = "asoc-simple-card",
- .id = 1,
- .dev = {
- .platform_data = &fsi2_hdmi_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .dma_mask = &fsi_hdmi_device.dev.coherent_dma_mask,
- },
-};
-
-/* RTC: RTC connects i2c-gpio. */
-static struct i2c_gpio_platform_data i2c_gpio_data = {
- .sda_pin = 208,
- .scl_pin = 91,
- .udelay = 5, /* 100 kHz */
-};
-
-static struct platform_device i2c_gpio_device = {
- .name = "i2c-gpio",
- .id = 2,
- .dev = {
- .platform_data = &i2c_gpio_data,
- },
-};
-
-/* I2C */
-static struct st1232_pdata st1232_i2c0_pdata = {
- .reset_gpio = 166,
-};
-
-static struct i2c_board_info i2c0_devices[] = {
- {
- I2C_BOARD_INFO("st1232-ts", 0x55),
- .irq = irq_pin(10),
- .platform_data = &st1232_i2c0_pdata,
- },
- {
- I2C_BOARD_INFO("wm8978", 0x1a),
- },
-};
-
-static struct i2c_board_info i2c2_devices[] = {
- {
- I2C_BOARD_INFO("s35390a", 0x30),
- .type = "s35390a",
- },
-};
-
-/*
- * board devices
- */
-static struct platform_device *eva_devices[] __initdata = {
- &lcdc0_device,
- &pwm_device,
- &pwm_backlight_device,
- &leds_gpio_device,
- &gpio_keys_device,
- &sh_eth_device,
- &vcc_sdhi0,
- &vccq_sdhi0,
- &sdhi0_device,
- &sh_mmcif_device,
- &hdmi_device,
- &hdmi_lcdc_device,
- &camera_device,
- &ceu0_device,
- &fsi_device,
- &fsi_wm8978_device,
- &fsi_hdmi_device,
- &i2c_gpio_device,
-};
-
-static const struct pinctrl_map eva_pinctrl_map[] = {
- /* CEU0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_data_0_7", "ceu0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_clk_0", "ceu0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_sync", "ceu0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_field", "ceu0"),
- /* FSIA */
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_sclk_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_mclk_out", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_data_in_1", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_data_out_0", "fsia"),
- /* FSIB */
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.1", "pfc-r8a7740",
- "fsib_mclk_in", "fsib"),
- /* GETHER */
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7740-gether", "pfc-r8a7740",
- "gether_mii", "gether"),
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7740-gether", "pfc-r8a7740",
- "gether_int", "gether"),
- /* HDMI */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-mobile-hdmi", "pfc-r8a7740",
- "hdmi", "hdmi"),
- /* LCD0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
- "lcd0_data24_0", "lcd0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
- "lcd0_lclk_1", "lcd0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
- "lcd0_sync", "lcd0"),
- /* MMCIF */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
- "mmc0_data8_1", "mmc0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
- "mmc0_ctrl_1", "mmc0"),
- /* SCIFA1 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.1", "pfc-r8a7740",
- "scifa1_data", "scifa1"),
- /* SDHI0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
- "sdhi0_data4", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
- "sdhi0_ctrl", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
- "sdhi0_wp", "sdhi0"),
- /* ST1232 */
- PIN_MAP_MUX_GROUP_DEFAULT("0-0055", "pfc-r8a7740",
- "intc_irq10", "intc"),
- /* TPU0 */
- PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm", "pfc-r8a7740",
- "tpu0_to2_1", "tpu0"),
- /* USBHS */
- PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-r8a7740",
- "intc_irq7_1", "intc"),
-};
-
-static void __init eva_clock_init(void)
-{
- struct clk *system = clk_get(NULL, "system_clk");
- struct clk *xtal1 = clk_get(NULL, "extal1");
- struct clk *usb24s = clk_get(NULL, "usb24s");
- struct clk *fsibck = clk_get(NULL, "fsibck");
-
- if (IS_ERR(system) ||
- IS_ERR(xtal1) ||
- IS_ERR(usb24s) ||
- IS_ERR(fsibck)) {
- pr_err("armadillo800eva board clock init failed\n");
- goto clock_error;
- }
-
- /* armadillo 800 eva extal1 is 24MHz */
- clk_set_rate(xtal1, 24000000);
-
- /* usb24s use extal1 (= system) clock (= 24MHz) */
- clk_set_parent(usb24s, system);
-
- /* FSIBCK is 12.288MHz, and it is parent of FSI-B */
- clk_set_rate(fsibck, 12288000);
-
-clock_error:
- if (!IS_ERR(system))
- clk_put(system);
- if (!IS_ERR(xtal1))
- clk_put(xtal1);
- if (!IS_ERR(usb24s))
- clk_put(usb24s);
- if (!IS_ERR(fsibck))
- clk_put(fsibck);
-}
-
-/*
- * board init
- */
-#define GPIO_PORT7CR IOMEM(0xe6050007)
-#define GPIO_PORT8CR IOMEM(0xe6050008)
-static void __init eva_init(void)
-{
- static struct pm_domain_device domain_devices[] __initdata = {
- { "A4LC", &lcdc0_device },
- { "A4LC", &hdmi_lcdc_device },
- { "A4MP", &hdmi_device },
- { "A4MP", &fsi_device },
- { "A4R", &ceu0_device },
- { "A4S", &sh_eth_device },
- { "A3SP", &pwm_device },
- { "A3SP", &sdhi0_device },
- { "A3SP", &sh_mmcif_device },
- };
- struct platform_device *usb = NULL, *sdhi1 = NULL;
-
- regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
- ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
- regulator_register_always_on(3, "fixed-5.0V", fixed5v0_power_consumers,
- ARRAY_SIZE(fixed5v0_power_consumers), 5000000);
-
- pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map));
- pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-
- r8a7740_pinmux_init();
- r8a7740_meram_workaround();
-
- /* GETHER */
- gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
-
- /* USB */
- gpio_request_one(159, GPIOF_IN, NULL); /* USB_DEVICE_MODE */
-
- if (gpio_get_value(159)) {
- /* USB Host */
- } else {
- /* USB Func */
- /*
- * The USBHS interrupt handlers needs to read the IRQ pin value
- * (HI/LOW) to diffentiate USB connection and disconnection
- * events (usbhsf_get_vbus()). We thus need to select both the
- * intc_irq7_1 pin group and GPIO 209 here.
- */
- gpio_request_one(209, GPIOF_IN, NULL);
-
- platform_device_register(&usbhsf_device);
- usb = &usbhsf_device;
- }
-
- /* CON1/CON15 Camera */
- gpio_request_one(173, GPIOF_OUT_INIT_LOW, NULL); /* STANDBY */
- gpio_request_one(172, GPIOF_OUT_INIT_HIGH, NULL); /* RST */
- /* see mt9t111_power() */
- gpio_request_one(158, GPIOF_OUT_INIT_LOW, NULL); /* CAM_PON */
-
- /* FSI-WM8978 */
- gpio_request(7, NULL);
- gpio_request(8, NULL);
- gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
- gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
-
- /*
- * CAUTION
- *
- * DBGMD/LCDC0/FSIA MUX
- * DBGMD_SELECT_B should be set after setting PFC Function.
- */
- gpio_request_one(176, GPIOF_OUT_INIT_HIGH, NULL);
-
- /*
- * We can switch CON8/CON14 by SW1.5,
- * but it needs after DBGMD_SELECT_B
- */
- gpio_request_one(6, GPIOF_IN, NULL);
- if (gpio_get_value(6)) {
- /* CON14 enable */
- } else {
- /* CON8 (SDHI1) enable */
- pinctrl_register_mappings(eva_sdhi1_pinctrl_map,
- ARRAY_SIZE(eva_sdhi1_pinctrl_map));
-
- platform_device_register(&vcc_sdhi1);
- platform_device_register(&sdhi1_device);
- sdhi1 = &sdhi1_device;
- }
-
-
-#ifdef CONFIG_CACHE_L2X0
- /* Shared attribute override enable, 32K*8way */
- l2x0_init(IOMEM(0xf0002000), 0x00400000, 0xc20f0fff);
-#endif
-
- i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
- i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices));
-
- r8a7740_add_standard_devices();
-
- platform_add_devices(eva_devices,
- ARRAY_SIZE(eva_devices));
-
- rmobile_add_devices_to_domains(domain_devices,
- ARRAY_SIZE(domain_devices));
- if (usb)
- rmobile_add_device_to_domain("A3SP", usb);
- if (sdhi1)
- rmobile_add_device_to_domain("A3SP", sdhi1);
-
- r8a7740_pm_init();
-}
-
-static void __init eva_earlytimer_init(void)
-{
- r8a7740_clock_init(MD_CK0 | MD_CK2);
- shmobile_earlytimer_init();
-
- /* the rate of extal1 clock must be set before late_time_init */
- eva_clock_init();
-}
-
-#define RESCNT2 IOMEM(0xe6188020)
-static void eva_restart(enum reboot_mode mode, const char *cmd)
-{
- /* Do soft power on reset */
- writel((1 << 31), RESCNT2);
-}
-
-static const char *eva_boards_compat_dt[] __initdata = {
- "renesas,armadillo800eva",
- NULL,
-};
-
-DT_MACHINE_START(ARMADILLO800EVA_DT, "armadillo800eva")
- .map_io = r8a7740_map_io,
- .init_early = r8a7740_add_early_devices,
- .init_irq = r8a7740_init_irq_of,
- .init_machine = eva_init,
- .init_late = shmobile_init_late,
- .init_time = eva_earlytimer_init,
- .dt_compat = eva_boards_compat_dt,
- .restart = eva_restart,
-MACHINE_END
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 05/15] ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The Armadillo-800 EVA board is sufficiently supported by DT-based and
board-less R-Mobile A1 (r8a7740) multiplatform kernels, and board
staging code. Hence remove the legacy board code to reduce maintenance
effort.
Lacking areas are:
- USB (it doesn't work in legacy, neither),
- HDMI (it doesn't work in legacy, neither),
- Camera (we don't care),
- DMAC/IPMMU (no DT bindings are planned).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 9 -
arch/arm/mach-shmobile/Makefile | 1 -
arch/arm/mach-shmobile/Makefile.boot | 1 -
arch/arm/mach-shmobile/board-armadillo800eva.c | 1365 ------------------------
4 files changed, 1376 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/board-armadillo800eva.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index bc8e2f60fe505ee2..e256c6b664710099 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -129,15 +129,6 @@ config ARCH_R8A7779
comment "Renesas ARM SoCs Board Type"
-config MACH_ARMADILLO800EVA
- bool "Armadillo-800 EVA board"
- depends on ARCH_R8A7740
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select SMSC_PHY if SH_ETH
- select SND_SOC_WM8978 if SND_SIMPLE_CARD && I2C
- select USE_OF
-
config MACH_BOCKW
bool "BOCK-W platform"
depends on ARCH_R8A7778
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 7e20ab3021be0ff2..4ffd7428353b53f9 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -58,7 +58,6 @@ else
obj-$(CONFIG_MACH_BOCKW) += board-bockw.o
obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
-obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
endif
# Framework support
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index 2269b1c3c30b108a..14cdfc0ed0755a59 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -1,6 +1,5 @@
# per-board load address for uImage
loadaddr-y :=
-loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000
loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
deleted file mode 100644
index bf37e3c532f661a6..0000000000000000
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ /dev/null
@@ -1,1365 +0,0 @@
-/*
- * armadillo 800 eva board support
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/i2c-gpio.h>
-#include <linux/input.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/mfd/tmio.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mmc/sh_mobile_sdhi.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/platform_data/st1232_pdata.h>
-#include <linux/platform_device.h>
-#include <linux/pwm.h>
-#include <linux/pwm_backlight.h>
-#include <linux/reboot.h>
-#include <linux/regulator/driver.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/gpio-regulator.h>
-#include <linux/regulator/machine.h>
-#include <linux/sh_eth.h>
-#include <linux/usb/renesas_usbhs.h>
-#include <linux/videodev2.h>
-
-#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/page.h>
-#include <media/mt9t112.h>
-#include <media/sh_mobile_ceu.h>
-#include <media/soc_camera.h>
-#include <sound/sh_fsi.h>
-#include <sound/simple_card.h>
-#include <video/sh_mobile_hdmi.h>
-#include <video/sh_mobile_lcdc.h>
-
-#include "common.h"
-#include "irqs.h"
-#include "pm-rmobile.h"
-#include "r8a7740.h"
-#include "sh-gpio.h"
-
-/*
- * CON1 Camera Module
- * CON2 Extension Bus
- * CON3 HDMI Output
- * CON4 Composite Video Output
- * CON5 H-UDI JTAG
- * CON6 ARM JTAG
- * CON7 SD1
- * CON8 SD2
- * CON9 RTC BackUp
- * CON10 Monaural Mic Input
- * CON11 Stereo Headphone Output
- * CON12 Audio Line Output(L)
- * CON13 Audio Line Output(R)
- * CON14 AWL13 Module
- * CON15 Extension
- * CON16 LCD1
- * CON17 LCD2
- * CON19 Power Input
- * CON20 USB1
- * CON21 USB2
- * CON22 Serial
- * CON23 LAN
- * CON24 USB3
- * LED1 Camera LED(Yellow)
- * LED2 Power LED (Green)
- * ED3-LED6 User LED(Yellow)
- * LED7 LAN link LED(Green)
- * LED8 LAN activity LED(Yellow)
- */
-
-/*
- * DipSwitch
- *
- * SW1
- *
- * -12345678-+---------------+----------------------------
- * 1 | boot | hermit
- * 0 | boot | OS auto boot
- * -12345678-+---------------+----------------------------
- * 00 | boot device | eMMC
- * 10 | boot device | SDHI0 (CON7)
- * 01 | boot device | -
- * 11 | boot device | Extension Buss (CS0)
- * -12345678-+---------------+----------------------------
- * 0 | Extension Bus | D8-D15 disable, eMMC enable
- * 1 | Extension Bus | D8-D15 enable, eMMC disable
- * -12345678-+---------------+----------------------------
- * 0 | SDHI1 | COM8 disable, COM14 enable
- * 1 | SDHI1 | COM8 enable, COM14 disable
- * -12345678-+---------------+----------------------------
- * 0 | USB0 | COM20 enable, COM24 disable
- * 1 | USB0 | COM20 disable, COM24 enable
- * -12345678-+---------------+----------------------------
- * 00 | JTAG | SH-X2
- * 10 | JTAG | ARM
- * 01 | JTAG | -
- * 11 | JTAG | Boundary Scan
- *-----------+---------------+----------------------------
- */
-
-/*
- * FSI-WM8978
- *
- * this command is required when playback.
- *
- * # amixer set "Headphone" 50
- *
- * this command is required when capture.
- *
- * # amixer set "Input PGA" 15
- * # amixer set "Left Input Mixer MicP" on
- * # amixer set "Left Input Mixer MicN" on
- * # amixer set "Right Input Mixer MicN" on
- * # amixer set "Right Input Mixer MicP" on
- */
-
-/*
- * USB function
- *
- * When you use USB Function,
- * set SW1.6 ON, and connect cable to CN24.
- *
- * USBF needs workaround on R8A7740 chip.
- * These are a little bit complex.
- * see
- * usbhsf_power_ctrl()
- */
-#define IRQ7 irq_pin(7)
-#define USBCR1 IOMEM(0xe605810a)
-#define USBH 0xC6700000
-#define USBH_USBCTR 0x10834
-
-struct usbhsf_private {
- struct clk *phy;
- struct clk *usb24;
- struct clk *pci;
- struct clk *func;
- struct clk *host;
- void __iomem *usbh_base;
- struct renesas_usbhs_platform_info info;
-};
-
-#define usbhsf_get_priv(pdev) \
- container_of(renesas_usbhs_get_info(pdev), \
- struct usbhsf_private, info)
-
-static int usbhsf_get_id(struct platform_device *pdev)
-{
- return USBHS_GADGET;
-}
-
-static int usbhsf_power_ctrl(struct platform_device *pdev,
- void __iomem *base, int enable)
-{
- struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-
- /*
- * Work around for USB Function.
- * It needs USB host clock, and settings
- */
- if (enable) {
- /*
- * enable all the related usb clocks
- * for usb workaround
- */
- clk_enable(priv->usb24);
- clk_enable(priv->pci);
- clk_enable(priv->host);
- clk_enable(priv->func);
- clk_enable(priv->phy);
-
- /*
- * set USBCR1
- *
- * Port1 is driven by USB function,
- * Port2 is driven by USB HOST
- * One HOST (Port1 or Port2 is HOST)
- * USB PLL input clock = 24MHz
- */
- __raw_writew(0xd750, USBCR1);
- mdelay(1);
-
- /*
- * start USB Host
- */
- __raw_writel(0x0000000c, priv->usbh_base + USBH_USBCTR);
- __raw_writel(0x00000008, priv->usbh_base + USBH_USBCTR);
- mdelay(10);
-
- /*
- * USB PHY Power ON
- */
- __raw_writew(0xd770, USBCR1);
- __raw_writew(0x4000, base + 0x102); /* USBF :: SUSPMODE */
-
- } else {
- __raw_writel(0x0000010f, priv->usbh_base + USBH_USBCTR);
- __raw_writew(0xd7c0, USBCR1); /* GPIO */
-
- clk_disable(priv->phy);
- clk_disable(priv->func); /* usb work around */
- clk_disable(priv->host); /* usb work around */
- clk_disable(priv->pci); /* usb work around */
- clk_disable(priv->usb24); /* usb work around */
- }
-
- return 0;
-}
-
-static int usbhsf_get_vbus(struct platform_device *pdev)
-{
- return gpio_get_value(209);
-}
-
-static irqreturn_t usbhsf_interrupt(int irq, void *data)
-{
- struct platform_device *pdev = data;
-
- renesas_usbhs_call_notify_hotplug(pdev);
-
- return IRQ_HANDLED;
-}
-
-static int usbhsf_hardware_exit(struct platform_device *pdev)
-{
- struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-
- if (!IS_ERR(priv->phy))
- clk_put(priv->phy);
- if (!IS_ERR(priv->usb24))
- clk_put(priv->usb24);
- if (!IS_ERR(priv->pci))
- clk_put(priv->pci);
- if (!IS_ERR(priv->host))
- clk_put(priv->host);
- if (!IS_ERR(priv->func))
- clk_put(priv->func);
- if (priv->usbh_base)
- iounmap(priv->usbh_base);
-
- priv->phy = NULL;
- priv->usb24 = NULL;
- priv->pci = NULL;
- priv->host = NULL;
- priv->func = NULL;
- priv->usbh_base = NULL;
-
- free_irq(IRQ7, pdev);
-
- return 0;
-}
-
-static int usbhsf_hardware_init(struct platform_device *pdev)
-{
- struct usbhsf_private *priv = usbhsf_get_priv(pdev);
- int ret;
-
- priv->phy = clk_get(&pdev->dev, "phy");
- priv->usb24 = clk_get(&pdev->dev, "usb24");
- priv->pci = clk_get(&pdev->dev, "pci");
- priv->func = clk_get(&pdev->dev, "func");
- priv->host = clk_get(&pdev->dev, "host");
- priv->usbh_base = ioremap_nocache(USBH, 0x20000);
-
- if (IS_ERR(priv->phy) ||
- IS_ERR(priv->usb24) ||
- IS_ERR(priv->pci) ||
- IS_ERR(priv->host) ||
- IS_ERR(priv->func) ||
- !priv->usbh_base) {
- dev_err(&pdev->dev, "USB clock setting failed\n");
- usbhsf_hardware_exit(pdev);
- return -EIO;
- }
-
- ret = request_irq(IRQ7, usbhsf_interrupt, IRQF_TRIGGER_NONE,
- dev_name(&pdev->dev), pdev);
- if (ret) {
- dev_err(&pdev->dev, "request_irq err\n");
- return ret;
- }
- irq_set_irq_type(IRQ7, IRQ_TYPE_EDGE_BOTH);
-
- /* usb24 use 1/1 of parent clock (= usb24s = 24MHz) */
- clk_set_rate(priv->usb24,
- clk_get_rate(clk_get_parent(priv->usb24)));
-
- return 0;
-}
-
-static struct usbhsf_private usbhsf_private = {
- .info = {
- .platform_callback = {
- .get_id = usbhsf_get_id,
- .get_vbus = usbhsf_get_vbus,
- .hardware_init = usbhsf_hardware_init,
- .hardware_exit = usbhsf_hardware_exit,
- .power_ctrl = usbhsf_power_ctrl,
- },
- .driver_param = {
- .buswait_bwait = 5,
- .detection_delay = 5,
- .d0_rx_id = SHDMA_SLAVE_USBHS_RX,
- .d1_tx_id = SHDMA_SLAVE_USBHS_TX,
- },
- }
-};
-
-static struct resource usbhsf_resources[] = {
- {
- .name = "USBHS",
- .start = 0xe6890000,
- .end = 0xe6890104 - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = gic_spi(51),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usbhsf_device = {
- .name = "renesas_usbhs",
- .dev = {
- .platform_data = &usbhsf_private.info,
- },
- .id = -1,
- .num_resources = ARRAY_SIZE(usbhsf_resources),
- .resource = usbhsf_resources,
-};
-
-/* Ether */
-static struct sh_eth_plat_data sh_eth_platdata = {
- .phy = 0x00, /* LAN8710A */
- .edmac_endian = EDMAC_LITTLE_ENDIAN,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource sh_eth_resources[] = {
- {
- .start = 0xe9a00000,
- .end = 0xe9a00800 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0xe9a01800,
- .end = 0xe9a02000 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = gic_spi(110),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sh_eth_device = {
- .name = "r8a7740-gether",
- .id = -1,
- .dev = {
- .platform_data = &sh_eth_platdata,
- .dma_mask = &sh_eth_device.dev.coherent_dma_mask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = sh_eth_resources,
- .num_resources = ARRAY_SIZE(sh_eth_resources),
-};
-
-/* PWM */
-static struct resource pwm_resources[] = {
- [0] = {
- .start = 0xe6600000,
- .end = 0xe66000ff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device pwm_device = {
- .name = "renesas-tpu-pwm",
- .id = -1,
- .num_resources = ARRAY_SIZE(pwm_resources),
- .resource = pwm_resources,
-};
-
-static struct pwm_lookup pwm_lookup[] = {
- PWM_LOOKUP("renesas-tpu-pwm", 2, "pwm-backlight.0", NULL,
- 33333, PWM_POLARITY_INVERSED),
-};
-
-/* LCDC and backlight */
-static struct platform_pwm_backlight_data pwm_backlight_data = {
- .lth_brightness = 50,
- .max_brightness = 255,
- .dft_brightness = 255,
- .pwm_period_ns = 33333, /* 30kHz */
- .enable_gpio = 61,
-};
-
-static struct platform_device pwm_backlight_device = {
- .name = "pwm-backlight",
- .dev = {
- .platform_data = &pwm_backlight_data,
- },
-};
-
-static struct fb_videomode lcdc0_mode = {
- .name = "AMPIER/AM-800480",
- .xres = 800,
- .yres = 480,
- .left_margin = 88,
- .right_margin = 40,
- .hsync_len = 128,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .sync = 0,
-};
-
-static struct sh_mobile_lcdc_info lcdc0_info = {
- .clock_source = LCDC_CLK_BUS,
- .ch[0] = {
- .chan = LCDC_CHAN_MAINLCD,
- .fourcc = V4L2_PIX_FMT_RGB565,
- .interface_type = RGB24,
- .clock_divider = 5,
- .flags = 0,
- .lcd_modes = &lcdc0_mode,
- .num_modes = 1,
- .panel_cfg = {
- .width = 111,
- .height = 68,
- },
- },
-};
-
-static struct resource lcdc0_resources[] = {
- [0] = {
- .name = "LCD0",
- .start = 0xfe940000,
- .end = 0xfe943fff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(177),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device lcdc0_device = {
- .name = "sh_mobile_lcdc_fb",
- .num_resources = ARRAY_SIZE(lcdc0_resources),
- .resource = lcdc0_resources,
- .id = 0,
- .dev = {
- .platform_data = &lcdc0_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-/*
- * LCDC1/HDMI
- */
-static struct sh_mobile_hdmi_info hdmi_info = {
- .flags = HDMI_OUTPUT_PUSH_PULL |
- HDMI_OUTPUT_POLARITY_HI |
- HDMI_32BIT_REG |
- HDMI_HAS_HTOP1 |
- HDMI_SND_SRC_SPDIF,
-};
-
-static struct resource hdmi_resources[] = {
- [0] = {
- .name = "HDMI",
- .start = 0xe6be0000,
- .end = 0xe6be03ff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(131),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .name = "HDMI emma3pf",
- .start = 0xe6be4000,
- .end = 0xe6be43ff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device hdmi_device = {
- .name = "sh-mobile-hdmi",
- .num_resources = ARRAY_SIZE(hdmi_resources),
- .resource = hdmi_resources,
- .id = -1,
- .dev = {
- .platform_data = &hdmi_info,
- },
-};
-
-static const struct fb_videomode lcdc1_mode = {
- .name = "HDMI 720p",
- .xres = 1280,
- .yres = 720,
- .pixclock = 13468,
- .left_margin = 220,
- .right_margin = 110,
- .hsync_len = 40,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .refresh = 60,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
-};
-
-static struct sh_mobile_lcdc_info hdmi_lcdc_info = {
- .clock_source = LCDC_CLK_PERIPHERAL, /* HDMI clock */
- .ch[0] = {
- .chan = LCDC_CHAN_MAINLCD,
- .fourcc = V4L2_PIX_FMT_RGB565,
- .interface_type = RGB24,
- .clock_divider = 1,
- .flags = LCDC_FLAGS_DWPOL,
- .lcd_modes = &lcdc1_mode,
- .num_modes = 1,
- .tx_dev = &hdmi_device,
- .panel_cfg = {
- .width = 1280,
- .height = 720,
- },
- },
-};
-
-static struct resource hdmi_lcdc_resources[] = {
- [0] = {
- .name = "LCDC1",
- .start = 0xfe944000,
- .end = 0xfe948000 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(178),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device hdmi_lcdc_device = {
- .name = "sh_mobile_lcdc_fb",
- .num_resources = ARRAY_SIZE(hdmi_lcdc_resources),
- .resource = hdmi_lcdc_resources,
- .id = 1,
- .dev = {
- .platform_data = &hdmi_lcdc_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-/* LEDS */
-static struct gpio_led gpio_leds[] = {
- {
- .name = "LED3",
- .gpio = 102,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- }, {
- .name = "LED4",
- .gpio = 111,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- }, {
- .name = "LED5",
- .gpio = 110,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- }, {
- .name = "LED6",
- .gpio = 177,
- .default_state = LEDS_GPIO_DEFSTATE_ON,
- },
-};
-
-static struct gpio_led_platform_data leds_gpio_info = {
- .leds = gpio_leds,
- .num_leds = ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &leds_gpio_info,
- },
-};
-
-/* GPIO KEY */
-#define GPIO_KEY(c, g, d, ...) \
- { .code = c, .gpio = g, .desc = d, .active_low = 1, __VA_ARGS__ }
-
-static struct gpio_keys_button gpio_buttons[] = {
- GPIO_KEY(KEY_POWER, 99, "SW3", .wakeup = 1),
- GPIO_KEY(KEY_BACK, 100, "SW4"),
- GPIO_KEY(KEY_MENU, 97, "SW5"),
- GPIO_KEY(KEY_HOME, 98, "SW6"),
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
- .buttons = gpio_buttons,
- .nbuttons = ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device gpio_keys_device = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &gpio_key_info,
- },
-};
-
-/* Fixed 3.3V regulator to be used by SDHI1, MMCIF */
-static struct regulator_consumer_supply fixed3v3_power_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
- REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
-};
-
-/* Fixed 3.3V regulator used by LCD backlight */
-static struct regulator_consumer_supply fixed5v0_power_consumers[] = {
- REGULATOR_SUPPLY("power", "pwm-backlight.0"),
-};
-
-/* Fixed 3.3V regulator to be used by SDHI0 */
-static struct regulator_consumer_supply vcc_sdhi0_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vcc_sdhi0_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
- .consumer_supplies = vcc_sdhi0_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi0_info = {
- .supply_name = "SDHI0 Vcc",
- .microvolts = 3300000,
- .gpio = 75,
- .enable_high = 1,
- .init_data = &vcc_sdhi0_init_data,
-};
-
-static struct platform_device vcc_sdhi0 = {
- .name = "reg-fixed-voltage",
- .id = 1,
- .dev = {
- .platform_data = &vcc_sdhi0_info,
- },
-};
-
-/* 1.8 / 3.3V SDHI0 VccQ regulator */
-static struct regulator_consumer_supply vccq_sdhi0_consumers[] = {
- REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vccq_sdhi0_init_data = {
- .constraints = {
- .input_uV = 3300000,
- .min_uV = 1800000,
- .max_uV = 3300000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vccq_sdhi0_consumers),
- .consumer_supplies = vccq_sdhi0_consumers,
-};
-
-static struct gpio vccq_sdhi0_gpios[] = {
- {17, GPIOF_OUT_INIT_LOW, "vccq-sdhi0" },
-};
-
-static struct gpio_regulator_state vccq_sdhi0_states[] = {
- { .value = 3300000, .gpios = (0 << 0) },
- { .value = 1800000, .gpios = (1 << 0) },
-};
-
-static struct gpio_regulator_config vccq_sdhi0_info = {
- .supply_name = "vqmmc",
-
- .enable_gpio = 74,
- .enable_high = 1,
- .enabled_at_boot = 0,
-
- .gpios = vccq_sdhi0_gpios,
- .nr_gpios = ARRAY_SIZE(vccq_sdhi0_gpios),
-
- .states = vccq_sdhi0_states,
- .nr_states = ARRAY_SIZE(vccq_sdhi0_states),
-
- .type = REGULATOR_VOLTAGE,
- .init_data = &vccq_sdhi0_init_data,
-};
-
-static struct platform_device vccq_sdhi0 = {
- .name = "gpio-regulator",
- .id = -1,
- .dev = {
- .platform_data = &vccq_sdhi0_info,
- },
-};
-
-/* Fixed 3.3V regulator to be used by SDHI1 */
-static struct regulator_consumer_supply vcc_sdhi1_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
-};
-
-static struct regulator_init_data vcc_sdhi1_init_data = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi1_consumers),
- .consumer_supplies = vcc_sdhi1_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi1_info = {
- .supply_name = "SDHI1 Vcc",
- .microvolts = 3300000,
- .gpio = 16,
- .enable_high = 1,
- .init_data = &vcc_sdhi1_init_data,
-};
-
-static struct platform_device vcc_sdhi1 = {
- .name = "reg-fixed-voltage",
- .id = 2,
- .dev = {
- .platform_data = &vcc_sdhi1_info,
- },
-};
-
-/* SDHI0 */
-static struct tmio_mmc_data sdhi0_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI0_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI0_RX,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
- MMC_CAP_POWER_OFF_CARD,
- .flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
- .cd_gpio = 167,
-};
-
-static struct resource sdhi0_resources[] = {
- {
- .name = "SDHI0",
- .start = 0xe6850000,
- .end = 0xe6850100 - 1,
- .flags = IORESOURCE_MEM,
- },
- /*
- * no SH_MOBILE_SDHI_IRQ_CARD_DETECT here
- */
- {
- .name = SH_MOBILE_SDHI_IRQ_SDCARD,
- .start = gic_spi(118),
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = SH_MOBILE_SDHI_IRQ_SDIO,
- .start = gic_spi(119),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi0_device = {
- .name = "sh_mobile_sdhi",
- .id = 0,
- .dev = {
- .platform_data = &sdhi0_info,
- },
- .num_resources = ARRAY_SIZE(sdhi0_resources),
- .resource = sdhi0_resources,
-};
-
-/* SDHI1 */
-static struct tmio_mmc_data sdhi1_info = {
- .chan_priv_tx = (void *)SHDMA_SLAVE_SDHI1_TX,
- .chan_priv_rx = (void *)SHDMA_SLAVE_SDHI1_RX,
- .capabilities = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
- MMC_CAP_POWER_OFF_CARD,
- .flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
- /* Port72 cannot generate IRQs, will be used in polling mode. */
- .cd_gpio = 72,
-};
-
-static struct resource sdhi1_resources[] = {
- [0] = {
- .name = "SDHI1",
- .start = 0xe6860000,
- .end = 0xe6860100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(121),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = gic_spi(122),
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .start = gic_spi(123),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sdhi1_device = {
- .name = "sh_mobile_sdhi",
- .id = 1,
- .dev = {
- .platform_data = &sdhi1_info,
- },
- .num_resources = ARRAY_SIZE(sdhi1_resources),
- .resource = sdhi1_resources,
-};
-
-static const struct pinctrl_map eva_sdhi1_pinctrl_map[] = {
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_data4", "sdhi1"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_ctrl", "sdhi1"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_cd", "sdhi1"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
- "sdhi1_wp", "sdhi1"),
-};
-
-/* MMCIF */
-static struct sh_mmcif_plat_data sh_mmcif_plat = {
- .sup_pclk = 0,
- .caps = MMC_CAP_4_BIT_DATA |
- MMC_CAP_8_BIT_DATA |
- MMC_CAP_NONREMOVABLE,
- .ccs_unsupported = true,
- .slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
- .slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
-};
-
-static struct resource sh_mmcif_resources[] = {
- [0] = {
- .name = "MMCIF",
- .start = 0xe6bd0000,
- .end = 0xe6bd0100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- /* MMC ERR */
- .start = gic_spi(56),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- /* MMC NOR */
- .start = gic_spi(57),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device sh_mmcif_device = {
- .name = "sh_mmcif",
- .id = -1,
- .dev = {
- .platform_data = &sh_mmcif_plat,
- },
- .num_resources = ARRAY_SIZE(sh_mmcif_resources),
- .resource = sh_mmcif_resources,
-};
-
-/* Camera */
-static int mt9t111_power(struct device *dev, int mode)
-{
- struct clk *mclk = clk_get(NULL, "video1");
-
- if (IS_ERR(mclk)) {
- dev_err(dev, "can't get video1 clock\n");
- return -EINVAL;
- }
-
- if (mode) {
- /* video1 (= CON1 camera) expect 24MHz */
- clk_set_rate(mclk, clk_round_rate(mclk, 24000000));
- clk_enable(mclk);
- gpio_set_value(158, 1);
- } else {
- gpio_set_value(158, 0);
- clk_disable(mclk);
- }
-
- clk_put(mclk);
-
- return 0;
-}
-
-static struct i2c_board_info i2c_camera_mt9t111 = {
- I2C_BOARD_INFO("mt9t112", 0x3d),
-};
-
-static struct mt9t112_camera_info mt9t111_info = {
- .divider = { 16, 0, 0, 7, 0, 10, 14, 7, 7 },
-};
-
-static struct soc_camera_link mt9t111_link = {
- .i2c_adapter_id = 0,
- .bus_id = 0,
- .board_info = &i2c_camera_mt9t111,
- .power = mt9t111_power,
- .priv = &mt9t111_info,
-};
-
-static struct platform_device camera_device = {
- .name = "soc-camera-pdrv",
- .id = 0,
- .dev = {
- .platform_data = &mt9t111_link,
- },
-};
-
-/* CEU0 */
-static struct sh_mobile_ceu_info sh_mobile_ceu0_info = {
- .flags = SH_CEU_FLAG_LOWER_8BIT,
-};
-
-static struct resource ceu0_resources[] = {
- [0] = {
- .name = "CEU",
- .start = 0xfe910000,
- .end = 0xfe91009f,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(160),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- /* place holder for contiguous memory */
- },
-};
-
-static struct platform_device ceu0_device = {
- .name = "sh_mobile_ceu",
- .id = 0,
- .num_resources = ARRAY_SIZE(ceu0_resources),
- .resource = ceu0_resources,
- .dev = {
- .platform_data = &sh_mobile_ceu0_info,
- .coherent_dma_mask = 0xffffffff,
- },
-};
-
-/* FSI */
-static struct sh_fsi_platform_info fsi_info = {
- /* FSI-WM8978 */
- .port_a = {
- .tx_id = SHDMA_SLAVE_FSIA_TX,
- },
- /* FSI-HDMI */
- .port_b = {
- .flags = SH_FSI_FMT_SPDIF |
- SH_FSI_ENABLE_STREAM_MODE |
- SH_FSI_CLK_CPG,
- .tx_id = SHDMA_SLAVE_FSIB_TX,
- }
-};
-
-static struct resource fsi_resources[] = {
- [0] = {
- .name = "FSI",
- .start = 0xfe1f0000,
- .end = 0xfe1f0400 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(9),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device fsi_device = {
- .name = "sh_fsi2",
- .id = -1,
- .num_resources = ARRAY_SIZE(fsi_resources),
- .resource = fsi_resources,
- .dev = {
- .platform_data = &fsi_info,
- },
-};
-
-/* FSI-WM8978 */
-static struct asoc_simple_card_info fsi_wm8978_info = {
- .name = "wm8978",
- .card = "FSI2A-WM8978",
- .codec = "wm8978.0-001a",
- .platform = "sh_fsi2",
- .daifmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
- .cpu_dai = {
- .name = "fsia-dai",
- },
- .codec_dai = {
- .name = "wm8978-hifi",
- .sysclk = 12288000,
- },
-};
-
-static struct platform_device fsi_wm8978_device = {
- .name = "asoc-simple-card",
- .id = 0,
- .dev = {
- .platform_data = &fsi_wm8978_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .dma_mask = &fsi_wm8978_device.dev.coherent_dma_mask,
- },
-};
-
-/* FSI-HDMI */
-static struct asoc_simple_card_info fsi2_hdmi_info = {
- .name = "HDMI",
- .card = "FSI2B-HDMI",
- .codec = "sh-mobile-hdmi",
- .platform = "sh_fsi2",
- .daifmt = SND_SOC_DAIFMT_CBS_CFS,
- .cpu_dai = {
- .name = "fsib-dai",
- },
- .codec_dai = {
- .name = "sh_mobile_hdmi-hifi",
- },
-};
-
-static struct platform_device fsi_hdmi_device = {
- .name = "asoc-simple-card",
- .id = 1,
- .dev = {
- .platform_data = &fsi2_hdmi_info,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .dma_mask = &fsi_hdmi_device.dev.coherent_dma_mask,
- },
-};
-
-/* RTC: RTC connects i2c-gpio. */
-static struct i2c_gpio_platform_data i2c_gpio_data = {
- .sda_pin = 208,
- .scl_pin = 91,
- .udelay = 5, /* 100 kHz */
-};
-
-static struct platform_device i2c_gpio_device = {
- .name = "i2c-gpio",
- .id = 2,
- .dev = {
- .platform_data = &i2c_gpio_data,
- },
-};
-
-/* I2C */
-static struct st1232_pdata st1232_i2c0_pdata = {
- .reset_gpio = 166,
-};
-
-static struct i2c_board_info i2c0_devices[] = {
- {
- I2C_BOARD_INFO("st1232-ts", 0x55),
- .irq = irq_pin(10),
- .platform_data = &st1232_i2c0_pdata,
- },
- {
- I2C_BOARD_INFO("wm8978", 0x1a),
- },
-};
-
-static struct i2c_board_info i2c2_devices[] = {
- {
- I2C_BOARD_INFO("s35390a", 0x30),
- .type = "s35390a",
- },
-};
-
-/*
- * board devices
- */
-static struct platform_device *eva_devices[] __initdata = {
- &lcdc0_device,
- &pwm_device,
- &pwm_backlight_device,
- &leds_gpio_device,
- &gpio_keys_device,
- &sh_eth_device,
- &vcc_sdhi0,
- &vccq_sdhi0,
- &sdhi0_device,
- &sh_mmcif_device,
- &hdmi_device,
- &hdmi_lcdc_device,
- &camera_device,
- &ceu0_device,
- &fsi_device,
- &fsi_wm8978_device,
- &fsi_hdmi_device,
- &i2c_gpio_device,
-};
-
-static const struct pinctrl_map eva_pinctrl_map[] = {
- /* CEU0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_data_0_7", "ceu0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_clk_0", "ceu0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_sync", "ceu0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
- "ceu0_field", "ceu0"),
- /* FSIA */
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_sclk_in", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_mclk_out", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_data_in_1", "fsia"),
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
- "fsia_data_out_0", "fsia"),
- /* FSIB */
- PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.1", "pfc-r8a7740",
- "fsib_mclk_in", "fsib"),
- /* GETHER */
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7740-gether", "pfc-r8a7740",
- "gether_mii", "gether"),
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7740-gether", "pfc-r8a7740",
- "gether_int", "gether"),
- /* HDMI */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-mobile-hdmi", "pfc-r8a7740",
- "hdmi", "hdmi"),
- /* LCD0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
- "lcd0_data24_0", "lcd0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
- "lcd0_lclk_1", "lcd0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
- "lcd0_sync", "lcd0"),
- /* MMCIF */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
- "mmc0_data8_1", "mmc0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
- "mmc0_ctrl_1", "mmc0"),
- /* SCIFA1 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.1", "pfc-r8a7740",
- "scifa1_data", "scifa1"),
- /* SDHI0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
- "sdhi0_data4", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
- "sdhi0_ctrl", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
- "sdhi0_wp", "sdhi0"),
- /* ST1232 */
- PIN_MAP_MUX_GROUP_DEFAULT("0-0055", "pfc-r8a7740",
- "intc_irq10", "intc"),
- /* TPU0 */
- PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm", "pfc-r8a7740",
- "tpu0_to2_1", "tpu0"),
- /* USBHS */
- PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-r8a7740",
- "intc_irq7_1", "intc"),
-};
-
-static void __init eva_clock_init(void)
-{
- struct clk *system = clk_get(NULL, "system_clk");
- struct clk *xtal1 = clk_get(NULL, "extal1");
- struct clk *usb24s = clk_get(NULL, "usb24s");
- struct clk *fsibck = clk_get(NULL, "fsibck");
-
- if (IS_ERR(system) ||
- IS_ERR(xtal1) ||
- IS_ERR(usb24s) ||
- IS_ERR(fsibck)) {
- pr_err("armadillo800eva board clock init failed\n");
- goto clock_error;
- }
-
- /* armadillo 800 eva extal1 is 24MHz */
- clk_set_rate(xtal1, 24000000);
-
- /* usb24s use extal1 (= system) clock (= 24MHz) */
- clk_set_parent(usb24s, system);
-
- /* FSIBCK is 12.288MHz, and it is parent of FSI-B */
- clk_set_rate(fsibck, 12288000);
-
-clock_error:
- if (!IS_ERR(system))
- clk_put(system);
- if (!IS_ERR(xtal1))
- clk_put(xtal1);
- if (!IS_ERR(usb24s))
- clk_put(usb24s);
- if (!IS_ERR(fsibck))
- clk_put(fsibck);
-}
-
-/*
- * board init
- */
-#define GPIO_PORT7CR IOMEM(0xe6050007)
-#define GPIO_PORT8CR IOMEM(0xe6050008)
-static void __init eva_init(void)
-{
- static struct pm_domain_device domain_devices[] __initdata = {
- { "A4LC", &lcdc0_device },
- { "A4LC", &hdmi_lcdc_device },
- { "A4MP", &hdmi_device },
- { "A4MP", &fsi_device },
- { "A4R", &ceu0_device },
- { "A4S", &sh_eth_device },
- { "A3SP", &pwm_device },
- { "A3SP", &sdhi0_device },
- { "A3SP", &sh_mmcif_device },
- };
- struct platform_device *usb = NULL, *sdhi1 = NULL;
-
- regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
- ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
- regulator_register_always_on(3, "fixed-5.0V", fixed5v0_power_consumers,
- ARRAY_SIZE(fixed5v0_power_consumers), 5000000);
-
- pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map));
- pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-
- r8a7740_pinmux_init();
- r8a7740_meram_workaround();
-
- /* GETHER */
- gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
-
- /* USB */
- gpio_request_one(159, GPIOF_IN, NULL); /* USB_DEVICE_MODE */
-
- if (gpio_get_value(159)) {
- /* USB Host */
- } else {
- /* USB Func */
- /*
- * The USBHS interrupt handlers needs to read the IRQ pin value
- * (HI/LOW) to diffentiate USB connection and disconnection
- * events (usbhsf_get_vbus()). We thus need to select both the
- * intc_irq7_1 pin group and GPIO 209 here.
- */
- gpio_request_one(209, GPIOF_IN, NULL);
-
- platform_device_register(&usbhsf_device);
- usb = &usbhsf_device;
- }
-
- /* CON1/CON15 Camera */
- gpio_request_one(173, GPIOF_OUT_INIT_LOW, NULL); /* STANDBY */
- gpio_request_one(172, GPIOF_OUT_INIT_HIGH, NULL); /* RST */
- /* see mt9t111_power() */
- gpio_request_one(158, GPIOF_OUT_INIT_LOW, NULL); /* CAM_PON */
-
- /* FSI-WM8978 */
- gpio_request(7, NULL);
- gpio_request(8, NULL);
- gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
- gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
-
- /*
- * CAUTION
- *
- * DBGMD/LCDC0/FSIA MUX
- * DBGMD_SELECT_B should be set after setting PFC Function.
- */
- gpio_request_one(176, GPIOF_OUT_INIT_HIGH, NULL);
-
- /*
- * We can switch CON8/CON14 by SW1.5,
- * but it needs after DBGMD_SELECT_B
- */
- gpio_request_one(6, GPIOF_IN, NULL);
- if (gpio_get_value(6)) {
- /* CON14 enable */
- } else {
- /* CON8 (SDHI1) enable */
- pinctrl_register_mappings(eva_sdhi1_pinctrl_map,
- ARRAY_SIZE(eva_sdhi1_pinctrl_map));
-
- platform_device_register(&vcc_sdhi1);
- platform_device_register(&sdhi1_device);
- sdhi1 = &sdhi1_device;
- }
-
-
-#ifdef CONFIG_CACHE_L2X0
- /* Shared attribute override enable, 32K*8way */
- l2x0_init(IOMEM(0xf0002000), 0x00400000, 0xc20f0fff);
-#endif
-
- i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
- i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices));
-
- r8a7740_add_standard_devices();
-
- platform_add_devices(eva_devices,
- ARRAY_SIZE(eva_devices));
-
- rmobile_add_devices_to_domains(domain_devices,
- ARRAY_SIZE(domain_devices));
- if (usb)
- rmobile_add_device_to_domain("A3SP", usb);
- if (sdhi1)
- rmobile_add_device_to_domain("A3SP", sdhi1);
-
- r8a7740_pm_init();
-}
-
-static void __init eva_earlytimer_init(void)
-{
- r8a7740_clock_init(MD_CK0 | MD_CK2);
- shmobile_earlytimer_init();
-
- /* the rate of extal1 clock must be set before late_time_init */
- eva_clock_init();
-}
-
-#define RESCNT2 IOMEM(0xe6188020)
-static void eva_restart(enum reboot_mode mode, const char *cmd)
-{
- /* Do soft power on reset */
- writel((1 << 31), RESCNT2);
-}
-
-static const char *eva_boards_compat_dt[] __initdata = {
- "renesas,armadillo800eva",
- NULL,
-};
-
-DT_MACHINE_START(ARMADILLO800EVA_DT, "armadillo800eva")
- .map_io = r8a7740_map_io,
- .init_early = r8a7740_add_early_devices,
- .init_irq = r8a7740_init_irq_of,
- .init_machine = eva_init,
- .init_late = shmobile_init_late,
- .init_time = eva_earlytimer_init,
- .dt_compat = eva_boards_compat_dt,
- .restart = eva_restart,
-MACHINE_END
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 06/15] ARM: shmobile: Remove legacy armadillo800eva_defconfig
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for Armadillo-800 EVA has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
MAINTAINERS | 1 -
arch/arm/configs/armadillo800eva_defconfig | 162 -----------------------------
2 files changed, 163 deletions(-)
delete mode 100644 arch/arm/configs/armadillo800eva_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index f1fe0cc0dadee9df..32ee18a233b6db80 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1455,7 +1455,6 @@ F: arch/arm/boot/dts/emev2*
F: arch/arm/boot/dts/r7s*
F: arch/arm/boot/dts/r8a*
F: arch/arm/boot/dts/sh*
-F: arch/arm/configs/armadillo800eva_defconfig
F: arch/arm/configs/bockw_defconfig
F: arch/arm/configs/marzen_defconfig
F: arch/arm/configs/shmobile_defconfig
diff --git a/arch/arm/configs/armadillo800eva_defconfig b/arch/arm/configs/armadillo800eva_defconfig
deleted file mode 100644
index 5666e3700a821814..0000000000000000
--- a/arch/arm/configs/armadillo800eva_defconfig
+++ /dev/null
@@ -1,162 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT\x16
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_PID_NS is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_R8A7740=y
-CONFIG_MACH_ARMADILLO800EVA=y
-# CONFIG_SH_TIMER_TMU is not set
-CONFIG_ARM_THUMB=y
-CONFIG_CACHE_L2X0=y
-CONFIG_ARM_ERRATA_430973=y
-CONFIG_ARM_ERRATA_458693=y
-CONFIG_ARM_ERRATA_460075=y
-CONFIG_PL310_ERRATA_588369=y
-CONFIG_ARM_ERRATA_720789=y
-CONFIG_PL310_ERRATA_727915=y
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_751472=y
-CONFIG_PL310_ERRATA_753970=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_PL310_ERRATA_769419=y
-CONFIG_ARM_ERRATA_775420=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_FORCE_MAX_ZONEORDER\x13
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_MD=y
-CONFIG_BLK_DEV_DM=y
-CONFIG_NETDEVICES=y
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_CHELSIO is not set
-# CONFIG_NET_VENDOR_CIRRUS is not set
-# CONFIG_NET_VENDOR_FARADAY is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-CONFIG_SH_ETH=y
-# CONFIG_NET_VENDOR_SEEQ is not set
-# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ST1232=y
-# CONFIG_SERIO is not set
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=9
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_GPIO=y
-CONFIG_I2C_SH_MOBILE=y
-# CONFIG_HWMON is not set
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_GPIO=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_VIDEO_DEV=y
-CONFIG_MEDIA_CAMERA_SUPPORT=y
-CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_SOC_CAMERA=y
-CONFIG_SOC_CAMERA_MT9T112=y
-CONFIG_VIDEO_SH_MOBILE_CEU=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_FB_SH_MOBILE_HDMI=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_PWM=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_SOC_SH4_FSI=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_USB_ETH=m
-CONFIG_MMC=y
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_S35390A=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV_GENIRQ=y
-CONFIG_PWM=y
-CONFIG_PWM_RENESAS_TPU=y
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-CONFIG_XZ_DEC=y
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 06/15] ARM: shmobile: Remove legacy armadillo800eva_defconfig
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for Armadillo-800 EVA has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
MAINTAINERS | 1 -
arch/arm/configs/armadillo800eva_defconfig | 162 -----------------------------
2 files changed, 163 deletions(-)
delete mode 100644 arch/arm/configs/armadillo800eva_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index f1fe0cc0dadee9df..32ee18a233b6db80 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1455,7 +1455,6 @@ F: arch/arm/boot/dts/emev2*
F: arch/arm/boot/dts/r7s*
F: arch/arm/boot/dts/r8a*
F: arch/arm/boot/dts/sh*
-F: arch/arm/configs/armadillo800eva_defconfig
F: arch/arm/configs/bockw_defconfig
F: arch/arm/configs/marzen_defconfig
F: arch/arm/configs/shmobile_defconfig
diff --git a/arch/arm/configs/armadillo800eva_defconfig b/arch/arm/configs/armadillo800eva_defconfig
deleted file mode 100644
index 5666e3700a821814..0000000000000000
--- a/arch/arm/configs/armadillo800eva_defconfig
+++ /dev/null
@@ -1,162 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_PID_NS is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_R8A7740=y
-CONFIG_MACH_ARMADILLO800EVA=y
-# CONFIG_SH_TIMER_TMU is not set
-CONFIG_ARM_THUMB=y
-CONFIG_CACHE_L2X0=y
-CONFIG_ARM_ERRATA_430973=y
-CONFIG_ARM_ERRATA_458693=y
-CONFIG_ARM_ERRATA_460075=y
-CONFIG_PL310_ERRATA_588369=y
-CONFIG_ARM_ERRATA_720789=y
-CONFIG_PL310_ERRATA_727915=y
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_751472=y
-CONFIG_PL310_ERRATA_753970=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_PL310_ERRATA_769419=y
-CONFIG_ARM_ERRATA_775420=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_FORCE_MAX_ZONEORDER=13
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_MD=y
-CONFIG_BLK_DEV_DM=y
-CONFIG_NETDEVICES=y
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_CHELSIO is not set
-# CONFIG_NET_VENDOR_CIRRUS is not set
-# CONFIG_NET_VENDOR_FARADAY is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-CONFIG_SH_ETH=y
-# CONFIG_NET_VENDOR_SEEQ is not set
-# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ST1232=y
-# CONFIG_SERIO is not set
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=9
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_GPIO=y
-CONFIG_I2C_SH_MOBILE=y
-# CONFIG_HWMON is not set
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_GPIO=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_VIDEO_DEV=y
-CONFIG_MEDIA_CAMERA_SUPPORT=y
-CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_SOC_CAMERA=y
-CONFIG_SOC_CAMERA_MT9T112=y
-CONFIG_VIDEO_SH_MOBILE_CEU=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_FB_SH_MOBILE_HDMI=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_PWM=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_SOC_SH4_FSI=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_USB_ETH=m
-CONFIG_MMC=y
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_S35390A=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV_GENIRQ=y
-CONFIG_PWM=y
-CONFIG_PWM_RENESAS_TPU=y
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-CONFIG_XZ_DEC=y
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 07/15] ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for Armadillo-800 EVA has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/boot/dts/Makefile | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e9eed01d48c5ccb5..332e9b1ed7a02c8f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -501,7 +501,6 @@ dtb-$(CONFIG_ARCH_S5PV210) += \
s5pv210-smdkv210.dtb \
s5pv210-torbreck.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
- r8a7740-armadillo800eva.dtb \
r8a7778-bockw.dtb \
r8a7778-bockw-reference.dtb \
r8a7779-marzen.dtb
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 07/15] ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The legacy board code for Armadillo-800 EVA has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/boot/dts/Makefile | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e9eed01d48c5ccb5..332e9b1ed7a02c8f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -501,7 +501,6 @@ dtb-$(CONFIG_ARCH_S5PV210) += \
s5pv210-smdkv210.dtb \
s5pv210-torbreck.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
- r8a7740-armadillo800eva.dtb \
r8a7778-bockw.dtb \
r8a7778-bockw-reference.dtb \
r8a7779-marzen.dtb
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 08/15] ARM: shmobile: Remove legacy SoC code for R-Mobile A1
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the R-Mobile A1 (r8a7740) legacy SoC code was the
Armadillo-800 EVA legacy board code, which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 7 -
arch/arm/mach-shmobile/Makefile | 3 +-
arch/arm/mach-shmobile/clock-r8a7740.c | 675 ------------------------------
arch/arm/mach-shmobile/pm-r8a7740.c | 129 ------
arch/arm/mach-shmobile/r8a7740.h | 58 ---
arch/arm/mach-shmobile/setup-r8a7740.c | 732 +--------------------------------
6 files changed, 4 insertions(+), 1600 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/clock-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/pm-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/r8a7740.h
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index e256c6b664710099..050bcd504458f6f0 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -108,13 +108,6 @@ if ARCH_SHMOBILE_LEGACY
comment "Renesas ARM SoCs System Type"
-config ARCH_R8A7740
- bool "R-Mobile A1 (R8A77400)"
- select ARCH_RMOBILE
- select ARCH_WANT_OPTIONAL_GPIOLIB
- select ARM_GIC
- select RENESAS_INTC_IRQPIN
-
config ARCH_R8A7778
bool "R-Car M1A (R8A77781)"
select ARCH_RCAR_GEN1
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 4ffd7428353b53f9..6cb095107f905d02 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -8,7 +8,7 @@ obj-y := timer.o console.o
# CPU objects
obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o
obj-$(CONFIG_ARCH_R8A73A4) += setup-r8a73a4.o
-obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o pm-r8a7740.o
+obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += setup-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += setup-r8a7779.o pm-r8a7779.o
obj-$(CONFIG_ARCH_R8A7790) += setup-r8a7790.o
@@ -21,7 +21,6 @@ obj-$(CONFIG_ARCH_R7S72100) += setup-r7s72100.o
# Clock objects
ifndef CONFIG_COMMON_CLK
obj-y += clock.o
-obj-$(CONFIG_ARCH_R8A7740) += clock-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += clock-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += clock-r8a7779.o
endif
diff --git a/arch/arm/mach-shmobile/clock-r8a7740.c b/arch/arm/mach-shmobile/clock-r8a7740.c
deleted file mode 100644
index 9cac8247c72b6e45..0000000000000000
--- a/arch/arm/mach-shmobile/clock-r8a7740.c
+++ /dev/null
@@ -1,675 +0,0 @@
-/*
- * R8A7740 processor support
- *
- * Copyright (C) 2011 Renesas Solutions Corp.
- * Copyright (C) 2011 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/sh_clk.h>
-#include <linux/clkdev.h>
-
-#include "clock.h"
-#include "common.h"
-#include "r8a7740.h"
-
-/*
- * | MDx | XTAL1/EXTAL1 | System | EXTALR |
- * Clock |-------+-----------------+ clock | 32.768 | RCLK
- * Mode | 2/1/0 | src MHz | source | KHz | source
- * -------+-------+-----------------+-----------+--------+----------
- * 0 | 0 0 0 | External 20~50 | XTAL1 | O | EXTALR
- * 1 | 0 0 1 | Crystal 20~30 | XTAL1 | O | EXTALR
- * 2 | 0 1 0 | External 40~50 | XTAL1 / 2 | O | EXTALR
- * 3 | 0 1 1 | Crystal 40~50 | XTAL1 / 2 | O | EXTALR
- * 4 | 1 0 0 | External 20~50 | XTAL1 | x | XTAL1 / 1024
- * 5 | 1 0 1 | Crystal 20~30 | XTAL1 | x | XTAL1 / 1024
- * 6 | 1 1 0 | External 40~50 | XTAL1 / 2 | x | XTAL1 / 2048
- * 7 | 1 1 1 | Crystal 40~50 | XTAL1 / 2 | x | XTAL1 / 2048
- */
-
-/* CPG registers */
-#define FRQCRA IOMEM(0xe6150000)
-#define FRQCRB IOMEM(0xe6150004)
-#define VCLKCR1 IOMEM(0xE6150008)
-#define VCLKCR2 IOMEM(0xE615000c)
-#define FRQCRC IOMEM(0xe61500e0)
-#define FSIACKCR IOMEM(0xe6150018)
-#define PLLC01CR IOMEM(0xe6150028)
-
-#define SUBCKCR IOMEM(0xe6150080)
-#define USBCKCR IOMEM(0xe615008c)
-
-#define MSTPSR0 IOMEM(0xe6150030)
-#define MSTPSR1 IOMEM(0xe6150038)
-#define MSTPSR2 IOMEM(0xe6150040)
-#define MSTPSR3 IOMEM(0xe6150048)
-#define MSTPSR4 IOMEM(0xe615004c)
-#define FSIBCKCR IOMEM(0xe6150090)
-#define HDMICKCR IOMEM(0xe6150094)
-#define SMSTPCR0 IOMEM(0xe6150130)
-#define SMSTPCR1 IOMEM(0xe6150134)
-#define SMSTPCR2 IOMEM(0xe6150138)
-#define SMSTPCR3 IOMEM(0xe615013c)
-#define SMSTPCR4 IOMEM(0xe6150140)
-
-#define FSIDIVA IOMEM(0xFE1F8000)
-#define FSIDIVB IOMEM(0xFE1F8008)
-
-/* Fixed 32 KHz root clock from EXTALR pin */
-static struct clk extalr_clk = {
- .rate = 32768,
-};
-
-/*
- * 25MHz default rate for the EXTAL1 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-static struct clk extal1_clk = {
- .rate = 25000000,
-};
-
-/*
- * 48MHz default rate for the EXTAL2 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-static struct clk extal2_clk = {
- .rate = 48000000,
-};
-
-/*
- * 27MHz default rate for the DV_CLKI root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-static struct clk dv_clk = {
- .rate = 27000000,
-};
-
-SH_CLK_RATIO(div2, 1, 2);
-SH_CLK_RATIO(div1k, 1, 1024);
-
-SH_FIXED_RATIO_CLK(extal1_div2_clk, extal1_clk, div2);
-SH_FIXED_RATIO_CLK(extal1_div1024_clk, extal1_clk, div1k);
-SH_FIXED_RATIO_CLK(extal1_div2048_clk, extal1_div2_clk, div1k);
-SH_FIXED_RATIO_CLK(extal2_div2_clk, extal2_clk, div2);
-
-static struct sh_clk_ops followparent_clk_ops = {
- .recalc = followparent_recalc,
-};
-
-/* Main clock */
-static struct clk system_clk = {
- .ops = &followparent_clk_ops,
-};
-
-SH_FIXED_RATIO_CLK(system_div2_clk, system_clk, div2);
-
-/* r_clk */
-static struct clk r_clk = {
- .ops = &followparent_clk_ops,
-};
-
-/* PLLC0/PLLC1 */
-static unsigned long pllc01_recalc(struct clk *clk)
-{
- unsigned long mult = 1;
-
- if (__raw_readl(PLLC01CR) & (1 << 14))
- mult = ((__raw_readl(clk->enable_reg) >> 24) & 0x7f) + 1;
-
- return clk->parent->rate * mult;
-}
-
-static struct sh_clk_ops pllc01_clk_ops = {
- .recalc = pllc01_recalc,
-};
-
-static struct clk pllc0_clk = {
- .ops = &pllc01_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &system_clk,
- .enable_reg = (void __iomem *)FRQCRC,
-};
-
-static struct clk pllc1_clk = {
- .ops = &pllc01_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &system_div2_clk,
- .enable_reg = (void __iomem *)FRQCRA,
-};
-
-/* PLLC1 / 2 */
-SH_FIXED_RATIO_CLK(pllc1_div2_clk, pllc1_clk, div2);
-
-/* USB clock */
-/*
- * USBCKCR is controlling usb24 clock
- * bit[7] : parent clock
- * bit[6] : clock divide rate
- * And this bit[7] is used as a "usb24s" from other devices.
- * (Video clock / Sub clock / SPU clock)
- * You can controll this clock as a below.
- *
- * struct clk *usb24 = clk_get(dev, "usb24");
- * struct clk *usb24s = clk_get(NULL, "usb24s");
- * struct clk *system = clk_get(NULL, "system_clk");
- * int rate = clk_get_rate(system);
- *
- * clk_set_parent(usb24s, system); // for bit[7]
- * clk_set_rate(usb24, rate / 2); // for bit[6]
- */
-static struct clk *usb24s_parents[] = {
- [0] = &system_clk,
- [1] = &extal2_clk
-};
-
-static int usb24s_enable(struct clk *clk)
-{
- __raw_writel(__raw_readl(USBCKCR) & ~(1 << 8), USBCKCR);
-
- return 0;
-}
-
-static void usb24s_disable(struct clk *clk)
-{
- __raw_writel(__raw_readl(USBCKCR) | (1 << 8), USBCKCR);
-}
-
-static int usb24s_set_parent(struct clk *clk, struct clk *parent)
-{
- int i, ret;
- u32 val;
-
- if (!clk->parent_table || !clk->parent_num)
- return -EINVAL;
-
- /* Search the parent */
- for (i = 0; i < clk->parent_num; i++)
- if (clk->parent_table[i] = parent)
- break;
-
- if (i = clk->parent_num)
- return -ENODEV;
-
- ret = clk_reparent(clk, parent);
- if (ret < 0)
- return ret;
-
- val = __raw_readl(USBCKCR);
- val &= ~(1 << 7);
- val |= i << 7;
- __raw_writel(val, USBCKCR);
-
- return 0;
-}
-
-static struct sh_clk_ops usb24s_clk_ops = {
- .recalc = followparent_recalc,
- .enable = usb24s_enable,
- .disable = usb24s_disable,
- .set_parent = usb24s_set_parent,
-};
-
-static struct clk usb24s_clk = {
- .ops = &usb24s_clk_ops,
- .parent_table = usb24s_parents,
- .parent_num = ARRAY_SIZE(usb24s_parents),
- .parent = &system_clk,
-};
-
-static unsigned long usb24_recalc(struct clk *clk)
-{
- return clk->parent->rate /
- ((__raw_readl(USBCKCR) & (1 << 6)) ? 1 : 2);
-};
-
-static int usb24_set_rate(struct clk *clk, unsigned long rate)
-{
- u32 val;
-
- /* closer to which ? parent->rate or parent->rate/2 */
- val = __raw_readl(USBCKCR);
- val &= ~(1 << 6);
- val |= (rate > (clk->parent->rate / 4) * 3) << 6;
- __raw_writel(val, USBCKCR);
-
- return 0;
-}
-
-static struct sh_clk_ops usb24_clk_ops = {
- .recalc = usb24_recalc,
- .set_rate = usb24_set_rate,
-};
-
-static struct clk usb24_clk = {
- .ops = &usb24_clk_ops,
- .parent = &usb24s_clk,
-};
-
-/* External FSIACK/FSIBCK clock */
-static struct clk fsiack_clk = {
-};
-
-static struct clk fsibck_clk = {
-};
-
-static struct clk *main_clks[] = {
- &extalr_clk,
- &extal1_clk,
- &extal2_clk,
- &extal1_div2_clk,
- &extal1_div1024_clk,
- &extal1_div2048_clk,
- &extal2_div2_clk,
- &dv_clk,
- &system_clk,
- &system_div2_clk,
- &r_clk,
- &pllc0_clk,
- &pllc1_clk,
- &pllc1_div2_clk,
- &usb24s_clk,
- &usb24_clk,
- &fsiack_clk,
- &fsibck_clk,
-};
-
-/* DIV4 clocks */
-static void div4_kick(struct clk *clk)
-{
- unsigned long value;
-
- /* set KICK bit in FRQCRB to update hardware setting */
- value = __raw_readl(FRQCRB);
- value |= (1 << 31);
- __raw_writel(value, FRQCRB);
-}
-
-static int divisors[] = { 2, 3, 4, 6, 8, 12, 16, 18,
- 24, 32, 36, 48, 0, 72, 96, 0 };
-
-static struct clk_div_mult_table div4_div_mult_table = {
- .divisors = divisors,
- .nr_divisors = ARRAY_SIZE(divisors),
-};
-
-static struct clk_div4_table div4_table = {
- .div_mult_table = &div4_div_mult_table,
- .kick = div4_kick,
-};
-
-enum {
- DIV4_I, DIV4_ZG, DIV4_B, DIV4_M1, DIV4_HP,
- DIV4_HPP, DIV4_USBP, DIV4_S, DIV4_ZB, DIV4_M3, DIV4_CP,
- DIV4_NR
-};
-
-static struct clk div4_clks[DIV4_NR] = {
- [DIV4_I] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 20, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_ZG] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 16, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_B] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 8, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_M1] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 4, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_HP] = SH_CLK_DIV4(&pllc1_clk, FRQCRB, 4, 0x6fff, 0),
- [DIV4_HPP] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 20, 0x6fff, 0),
- [DIV4_USBP] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 16, 0x6fff, 0),
- [DIV4_S] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 12, 0x6fff, 0),
- [DIV4_ZB] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 8, 0x6fff, 0),
- [DIV4_M3] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 4, 0x6fff, 0),
- [DIV4_CP] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 0, 0x6fff, 0),
-};
-
-/* DIV6 reparent */
-enum {
- DIV6_HDMI,
- DIV6_VCLK1, DIV6_VCLK2,
- DIV6_FSIA, DIV6_FSIB,
- DIV6_REPARENT_NR,
-};
-
-static struct clk *hdmi_parent[] = {
- [0] = &pllc1_div2_clk,
- [1] = &system_clk,
- [2] = &dv_clk
-};
-
-static struct clk *vclk_parents[8] = {
- [0] = &pllc1_div2_clk,
- [2] = &dv_clk,
- [3] = &usb24s_clk,
- [4] = &extal1_div2_clk,
- [5] = &extalr_clk,
-};
-
-static struct clk *fsia_parents[] = {
- [0] = &pllc1_div2_clk,
- [1] = &fsiack_clk, /* external clock */
-};
-
-static struct clk *fsib_parents[] = {
- [0] = &pllc1_div2_clk,
- [1] = &fsibck_clk, /* external clock */
-};
-
-static struct clk div6_reparent_clks[DIV6_REPARENT_NR] = {
- [DIV6_HDMI] = SH_CLK_DIV6_EXT(HDMICKCR, 0,
- hdmi_parent, ARRAY_SIZE(hdmi_parent), 6, 2),
- [DIV6_VCLK1] = SH_CLK_DIV6_EXT(VCLKCR1, 0,
- vclk_parents, ARRAY_SIZE(vclk_parents), 12, 3),
- [DIV6_VCLK2] = SH_CLK_DIV6_EXT(VCLKCR2, 0,
- vclk_parents, ARRAY_SIZE(vclk_parents), 12, 3),
- [DIV6_FSIA] = SH_CLK_DIV6_EXT(FSIACKCR, 0,
- fsia_parents, ARRAY_SIZE(fsia_parents), 6, 2),
- [DIV6_FSIB] = SH_CLK_DIV6_EXT(FSIBCKCR, 0,
- fsib_parents, ARRAY_SIZE(fsib_parents), 6, 2),
-};
-
-/* DIV6 clocks */
-enum {
- DIV6_SUB,
- DIV6_NR
-};
-
-static struct clk div6_clks[DIV6_NR] = {
- [DIV6_SUB] = SH_CLK_DIV6(&pllc1_div2_clk, SUBCKCR, 0),
-};
-
-/* HDMI1/2 clock */
-static unsigned long hdmi12_recalc(struct clk *clk)
-{
- u32 val = __raw_readl(HDMICKCR);
- int shift = (int)clk->priv;
-
- val >>= shift;
- val &= 0x3;
-
- return clk->parent->rate / (1 << val);
-};
-
-static int hdmi12_set_rate(struct clk *clk, unsigned long rate)
-{
- u32 val, mask;
- int i, shift;
-
- for (i = 0; i < 3; i++)
- if (rate = clk->parent->rate / (1 << i))
- goto find;
- return -ENODEV;
-
-find:
- shift = (int)clk->priv;
-
- val = __raw_readl(HDMICKCR);
- mask = ~(0x3 << shift);
- val = (val & mask) | i << shift;
- __raw_writel(val, HDMICKCR);
-
- return 0;
-};
-
-static struct sh_clk_ops hdmi12_clk_ops = {
- .recalc = hdmi12_recalc,
- .set_rate = hdmi12_set_rate,
-};
-
-static struct clk hdmi1_clk = {
- .ops = &hdmi12_clk_ops,
- .priv = (void *)9,
- .parent = &div6_reparent_clks[DIV6_HDMI], /* late install */
-};
-
-static struct clk hdmi2_clk = {
- .ops = &hdmi12_clk_ops,
- .priv = (void *)11,
- .parent = &div6_reparent_clks[DIV6_HDMI], /* late install */
-};
-
-static struct clk *late_main_clks[] = {
- &hdmi1_clk,
- &hdmi2_clk,
-};
-
-/* FSI DIV */
-enum { FSIDIV_A, FSIDIV_B, FSIDIV_REPARENT_NR };
-
-static struct clk fsidivs[] = {
- [FSIDIV_A] = SH_CLK_FSIDIV(FSIDIVA, &div6_reparent_clks[DIV6_FSIA]),
- [FSIDIV_B] = SH_CLK_FSIDIV(FSIDIVB, &div6_reparent_clks[DIV6_FSIB]),
-};
-
-/* MSTP */
-enum {
- MSTP128, MSTP127, MSTP125,
- MSTP116, MSTP111, MSTP100, MSTP117,
-
- MSTP230, MSTP229,
- MSTP222,
- MSTP218, MSTP217, MSTP216, MSTP214,
- MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
-
- MSTP329, MSTP328, MSTP323, MSTP320,
- MSTP314, MSTP313, MSTP312,
- MSTP309, MSTP304,
-
- MSTP416, MSTP415, MSTP407, MSTP406,
-
- MSTP_NR
-};
-
-static struct clk mstp_clks[MSTP_NR] = {
- [MSTP128] = SH_CLK_MSTP32(&div4_clks[DIV4_S], SMSTPCR1, 28, 0), /* CEU21 */
- [MSTP127] = SH_CLK_MSTP32(&div4_clks[DIV4_S], SMSTPCR1, 27, 0), /* CEU20 */
- [MSTP125] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR1, 25, 0), /* TMU0 */
- [MSTP117] = SH_CLK_MSTP32(&div4_clks[DIV4_B], SMSTPCR1, 17, 0), /* LCDC1 */
- [MSTP116] = SH_CLK_MSTP32(&div4_clks[DIV4_HPP], SMSTPCR1, 16, 0), /* IIC0 */
- [MSTP111] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR1, 11, 0), /* TMU1 */
- [MSTP100] = SH_CLK_MSTP32(&div4_clks[DIV4_B], SMSTPCR1, 0, 0), /* LCDC0 */
-
- [MSTP230] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 30, 0), /* SCIFA6 */
- [MSTP229] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 29, 0), /* INTCA */
- [MSTP222] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 22, 0), /* SCIFA7 */
- [MSTP218] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* DMAC1 */
- [MSTP217] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 17, 0), /* DMAC2 */
- [MSTP216] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 16, 0), /* DMAC3 */
- [MSTP214] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 14, 0), /* USBDMAC */
- [MSTP207] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */
- [MSTP206] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */
- [MSTP204] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */
- [MSTP203] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 3, 0), /* SCIFA1 */
- [MSTP202] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 2, 0), /* SCIFA2 */
- [MSTP201] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 1, 0), /* SCIFA3 */
- [MSTP200] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 0, 0), /* SCIFA4 */
-
- [MSTP329] = SH_CLK_MSTP32(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */
- [MSTP328] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 28, 0), /* FSI */
- [MSTP323] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR3, 23, 0), /* IIC1 */
- [MSTP320] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 20, 0), /* USBF */
- [MSTP314] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 14, 0), /* SDHI0 */
- [MSTP313] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 13, 0), /* SDHI1 */
- [MSTP312] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 12, 0), /* MMC */
- [MSTP309] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 9, 0), /* GEther */
- [MSTP304] = SH_CLK_MSTP32(&div4_clks[DIV4_CP], SMSTPCR3, 4, 0), /* TPU0 */
-
- [MSTP416] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 16, 0), /* USBHOST */
- [MSTP415] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 15, 0), /* SDHI2 */
- [MSTP407] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 7, 0), /* USB-Func */
- [MSTP406] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 6, 0), /* USB Phy */
-};
-
-static struct clk_lookup lookups[] = {
- /* main clocks */
- CLKDEV_CON_ID("extalr", &extalr_clk),
- CLKDEV_CON_ID("extal1", &extal1_clk),
- CLKDEV_CON_ID("extal2", &extal2_clk),
- CLKDEV_CON_ID("extal1_div2", &extal1_div2_clk),
- CLKDEV_CON_ID("extal1_div1024", &extal1_div1024_clk),
- CLKDEV_CON_ID("extal1_div2048", &extal1_div2048_clk),
- CLKDEV_CON_ID("extal2_div2", &extal2_div2_clk),
- CLKDEV_CON_ID("dv_clk", &dv_clk),
- CLKDEV_CON_ID("system_clk", &system_clk),
- CLKDEV_CON_ID("system_div2_clk", &system_div2_clk),
- CLKDEV_CON_ID("r_clk", &r_clk),
- CLKDEV_CON_ID("pllc0_clk", &pllc0_clk),
- CLKDEV_CON_ID("pllc1_clk", &pllc1_clk),
- CLKDEV_CON_ID("pllc1_div2_clk", &pllc1_div2_clk),
- CLKDEV_CON_ID("usb24s", &usb24s_clk),
- CLKDEV_CON_ID("hdmi1", &hdmi1_clk),
- CLKDEV_CON_ID("hdmi2", &hdmi2_clk),
- CLKDEV_CON_ID("video1", &div6_reparent_clks[DIV6_VCLK1]),
- CLKDEV_CON_ID("video2", &div6_reparent_clks[DIV6_VCLK2]),
- CLKDEV_CON_ID("fsiack", &fsiack_clk),
- CLKDEV_CON_ID("fsibck", &fsibck_clk),
-
- /* DIV4 clocks */
- CLKDEV_CON_ID("i_clk", &div4_clks[DIV4_I]),
- CLKDEV_CON_ID("zg_clk", &div4_clks[DIV4_ZG]),
- CLKDEV_CON_ID("b_clk", &div4_clks[DIV4_B]),
- CLKDEV_CON_ID("m1_clk", &div4_clks[DIV4_M1]),
- CLKDEV_CON_ID("hp_clk", &div4_clks[DIV4_HP]),
- CLKDEV_CON_ID("hpp_clk", &div4_clks[DIV4_HPP]),
- CLKDEV_CON_ID("s_clk", &div4_clks[DIV4_S]),
- CLKDEV_CON_ID("zb_clk", &div4_clks[DIV4_ZB]),
- CLKDEV_CON_ID("m3_clk", &div4_clks[DIV4_M3]),
- CLKDEV_CON_ID("cp_clk", &div4_clks[DIV4_CP]),
-
- /* DIV6 clocks */
- CLKDEV_CON_ID("sub_clk", &div6_clks[DIV6_SUB]),
-
- /* MSTP32 clocks */
- CLKDEV_DEV_ID("sh_mobile_lcdc_fb.0", &mstp_clks[MSTP100]),
- CLKDEV_DEV_ID("i2c-sh_mobile.0", &mstp_clks[MSTP116]),
- CLKDEV_DEV_ID("fff20000.i2c", &mstp_clks[MSTP116]),
- CLKDEV_DEV_ID("sh_mobile_lcdc_fb.1", &mstp_clks[MSTP117]),
- CLKDEV_DEV_ID("sh_mobile_ceu.0", &mstp_clks[MSTP127]),
- CLKDEV_DEV_ID("sh_mobile_ceu.1", &mstp_clks[MSTP128]),
-
- CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP200]),
- CLKDEV_DEV_ID("e6c80000.serial", &mstp_clks[MSTP200]),
- CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP201]),
- CLKDEV_DEV_ID("e6c70000.serial", &mstp_clks[MSTP201]),
- CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP202]),
- CLKDEV_DEV_ID("e6c60000.serial", &mstp_clks[MSTP202]),
- CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]),
- CLKDEV_DEV_ID("e6c50000.serial", &mstp_clks[MSTP203]),
- CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]),
- CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]),
- CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]),
- CLKDEV_DEV_ID("e6c30000.serial", &mstp_clks[MSTP206]),
- CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]),
- CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]),
- CLKDEV_DEV_ID("sh-dma-engine.3", &mstp_clks[MSTP214]),
- CLKDEV_DEV_ID("sh-dma-engine.2", &mstp_clks[MSTP216]),
- CLKDEV_DEV_ID("sh-dma-engine.1", &mstp_clks[MSTP217]),
- CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]),
- CLKDEV_DEV_ID("sh-sci.7", &mstp_clks[MSTP222]),
- CLKDEV_DEV_ID("e6cd0000.serial", &mstp_clks[MSTP222]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.0", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.1", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.2", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.3", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP230]),
- CLKDEV_DEV_ID("e6cc0000.serial", &mstp_clks[MSTP230]),
-
- CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]),
- CLKDEV_DEV_ID("fe1f0000.sound", &mstp_clks[MSTP328]),
- CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]),
- CLKDEV_DEV_ID("e6c20000.i2c", &mstp_clks[MSTP323]),
- CLKDEV_DEV_ID("renesas_usbhs", &mstp_clks[MSTP320]),
- CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP314]),
- CLKDEV_DEV_ID("e6850000.sd", &mstp_clks[MSTP314]),
- CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP313]),
- CLKDEV_DEV_ID("e6860000.sd", &mstp_clks[MSTP313]),
- CLKDEV_DEV_ID("sh_mmcif", &mstp_clks[MSTP312]),
- CLKDEV_DEV_ID("e6bd0000.mmc", &mstp_clks[MSTP312]),
- CLKDEV_DEV_ID("r8a7740-gether", &mstp_clks[MSTP309]),
- CLKDEV_DEV_ID("e9a00000.ethernet", &mstp_clks[MSTP309]),
- CLKDEV_DEV_ID("renesas-tpu-pwm", &mstp_clks[MSTP304]),
- CLKDEV_DEV_ID("e6600000.pwm", &mstp_clks[MSTP304]),
-
- CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP415]),
- CLKDEV_DEV_ID("e6870000.sd", &mstp_clks[MSTP415]),
-
- /* ICK */
- CLKDEV_ICK_ID("fck", "sh-tmu.1", &mstp_clks[MSTP111]),
- CLKDEV_ICK_ID("fck", "fff90000.timer", &mstp_clks[MSTP111]),
- CLKDEV_ICK_ID("fck", "sh-tmu.0", &mstp_clks[MSTP125]),
- CLKDEV_ICK_ID("fck", "fff80000.timer", &mstp_clks[MSTP125]),
- CLKDEV_ICK_ID("fck", "sh-cmt-48.1", &mstp_clks[MSTP329]),
- CLKDEV_ICK_ID("fck", "e6138000.timer", &mstp_clks[MSTP329]),
- CLKDEV_ICK_ID("host", "renesas_usbhs", &mstp_clks[MSTP416]),
- CLKDEV_ICK_ID("func", "renesas_usbhs", &mstp_clks[MSTP407]),
- CLKDEV_ICK_ID("phy", "renesas_usbhs", &mstp_clks[MSTP406]),
- CLKDEV_ICK_ID("pci", "renesas_usbhs", &div4_clks[DIV4_USBP]),
- CLKDEV_ICK_ID("usb24", "renesas_usbhs", &usb24_clk),
- CLKDEV_ICK_ID("ick", "sh-mobile-hdmi", &div6_reparent_clks[DIV6_HDMI]),
-
- CLKDEV_ICK_ID("icka", "sh_fsi2", &div6_reparent_clks[DIV6_FSIA]),
- CLKDEV_ICK_ID("ickb", "sh_fsi2", &div6_reparent_clks[DIV6_FSIB]),
- CLKDEV_ICK_ID("diva", "sh_fsi2", &fsidivs[FSIDIV_A]),
- CLKDEV_ICK_ID("divb", "sh_fsi2", &fsidivs[FSIDIV_B]),
- CLKDEV_ICK_ID("xcka", "sh_fsi2", &fsiack_clk),
- CLKDEV_ICK_ID("xckb", "sh_fsi2", &fsibck_clk),
-};
-
-void __init r8a7740_clock_init(u8 md_ck)
-{
- int k, ret = 0;
-
- /* detect system clock parent */
- if (md_ck & MD_CK1)
- system_clk.parent = &extal1_div2_clk;
- else
- system_clk.parent = &extal1_clk;
-
- /* detect RCLK parent */
- switch (md_ck & (MD_CK2 | MD_CK1)) {
- case MD_CK2 | MD_CK1:
- r_clk.parent = &extal1_div2048_clk;
- break;
- case MD_CK2:
- r_clk.parent = &extal1_div1024_clk;
- break;
- case MD_CK1:
- default:
- r_clk.parent = &extalr_clk;
- break;
- }
-
- for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
- ret = clk_register(main_clks[k]);
-
- if (!ret)
- ret = sh_clk_div4_register(div4_clks, DIV4_NR, &div4_table);
-
- if (!ret)
- ret = sh_clk_div6_register(div6_clks, DIV6_NR);
-
- if (!ret)
- ret = sh_clk_div6_reparent_register(div6_reparent_clks,
- DIV6_REPARENT_NR);
-
- if (!ret)
- ret = sh_clk_mstp_register(mstp_clks, MSTP_NR);
-
- for (k = 0; !ret && (k < ARRAY_SIZE(late_main_clks)); k++)
- ret = clk_register(late_main_clks[k]);
-
- if (!ret)
- ret = sh_clk_fsidiv_register(fsidivs, FSIDIV_REPARENT_NR);
-
- clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-
- if (!ret)
- shmobile_clk_init();
- else
- panic("failed to setup r8a7740 clocks\n");
-}
diff --git a/arch/arm/mach-shmobile/pm-r8a7740.c b/arch/arm/mach-shmobile/pm-r8a7740.c
deleted file mode 100644
index 34608fcf064808b8..0000000000000000
--- a/arch/arm/mach-shmobile/pm-r8a7740.c
+++ /dev/null
@@ -1,129 +0,0 @@
-/*
- * r8a7740 power management support
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#include <linux/console.h>
-#include <linux/io.h>
-#include <linux/suspend.h>
-
-#include "common.h"
-#include "pm-rmobile.h"
-
-#define SYSC_BASE IOMEM(0xe6180000)
-
-#if defined(CONFIG_PM) && !defined(CONFIG_ARCH_MULTIPLATFORM)
-static int r8a7740_pd_a3sm_suspend(void)
-{
- /*
- * The A3SM domain contains the CPU core and therefore it should
- * only be turned off if the CPU is not in use.
- */
- return -EBUSY;
-}
-
-static int r8a7740_pd_a3sp_suspend(void)
-{
- /*
- * Serial consoles make use of SCIF hardware located in A3SP,
- * keep such power domain on if "no_console_suspend" is set.
- */
- return console_suspend_enabled ? 0 : -EBUSY;
-}
-
-static int r8a7740_pd_d4_suspend(void)
-{
- /*
- * The D4 domain contains the Coresight-ETM hardware block and
- * therefore it should only be turned off if the debug module is
- * not in use.
- */
- return -EBUSY;
-}
-
-static struct rmobile_pm_domain r8a7740_pm_domains[] = {
- {
- .genpd.name = "A4LC",
- .base = SYSC_BASE,
- .bit_shift = 1,
- }, {
- .genpd.name = "A4MP",
- .base = SYSC_BASE,
- .bit_shift = 2,
- }, {
- .genpd.name = "D4",
- .base = SYSC_BASE,
- .bit_shift = 3,
- .gov = &pm_domain_always_on_gov,
- .suspend = r8a7740_pd_d4_suspend,
- }, {
- .genpd.name = "A4R",
- .base = SYSC_BASE,
- .bit_shift = 5,
- }, {
- .genpd.name = "A3RV",
- .base = SYSC_BASE,
- .bit_shift = 6,
- }, {
- .genpd.name = "A4S",
- .base = SYSC_BASE,
- .bit_shift = 10,
- .no_debug = true,
- }, {
- .genpd.name = "A3SP",
- .base = SYSC_BASE,
- .bit_shift = 11,
- .gov = &pm_domain_always_on_gov,
- .no_debug = true,
- .suspend = r8a7740_pd_a3sp_suspend,
- }, {
- .genpd.name = "A3SM",
- .base = SYSC_BASE,
- .bit_shift = 12,
- .gov = &pm_domain_always_on_gov,
- .suspend = r8a7740_pd_a3sm_suspend,
- }, {
- .genpd.name = "A3SG",
- .base = SYSC_BASE,
- .bit_shift = 13,
- }, {
- .genpd.name = "A4SU",
- .base = SYSC_BASE,
- .bit_shift = 20,
- },
-};
-
-void __init r8a7740_init_pm_domains(void)
-{
- rmobile_init_domains(r8a7740_pm_domains, ARRAY_SIZE(r8a7740_pm_domains));
- pm_genpd_add_subdomain_names("A4R", "A3RV");
- pm_genpd_add_subdomain_names("A4S", "A3SP");
- pm_genpd_add_subdomain_names("A4S", "A3SM");
- pm_genpd_add_subdomain_names("A4S", "A3SG");
-}
-#endif /* CONFIG_PM && !CONFIG_ARCH_MULTIPLATFORM */
-
-#ifdef CONFIG_SUSPEND
-static int r8a7740_enter_suspend(suspend_state_t suspend_state)
-{
- cpu_do_idle();
- return 0;
-}
-
-static void r8a7740_suspend_init(void)
-{
- shmobile_suspend_ops.enter = r8a7740_enter_suspend;
-}
-#else
-static void r8a7740_suspend_init(void) {}
-#endif
-
-void __init r8a7740_pm_init(void)
-{
- r8a7740_suspend_init();
-}
diff --git a/arch/arm/mach-shmobile/r8a7740.h b/arch/arm/mach-shmobile/r8a7740.h
deleted file mode 100644
index ca7805ad7ea3d64e..0000000000000000
--- a/arch/arm/mach-shmobile/r8a7740.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright (C) 2011 Renesas Solutions Corp.
- * Copyright (C) 2011 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_R8A7740_H__
-#define __ASM_R8A7740_H__
-
-/*
- * MD_CKx pin
- */
-#define MD_CK2 (1 << 2)
-#define MD_CK1 (1 << 1)
-#define MD_CK0 (1 << 0)
-
-/* DMA slave IDs */
-enum {
- SHDMA_SLAVE_INVALID,
- SHDMA_SLAVE_SDHI0_RX,
- SHDMA_SLAVE_SDHI0_TX,
- SHDMA_SLAVE_SDHI1_RX,
- SHDMA_SLAVE_SDHI1_TX,
- SHDMA_SLAVE_SDHI2_RX,
- SHDMA_SLAVE_SDHI2_TX,
- SHDMA_SLAVE_FSIA_RX,
- SHDMA_SLAVE_FSIA_TX,
- SHDMA_SLAVE_FSIB_TX,
- SHDMA_SLAVE_USBHS_TX,
- SHDMA_SLAVE_USBHS_RX,
- SHDMA_SLAVE_MMCIF_TX,
- SHDMA_SLAVE_MMCIF_RX,
-};
-
-extern void r8a7740_meram_workaround(void);
-extern void r8a7740_init_irq_of(void);
-extern void r8a7740_map_io(void);
-extern void r8a7740_add_early_devices(void);
-extern void r8a7740_add_standard_devices(void);
-extern void r8a7740_clock_init(u8 md_ck);
-extern void r8a7740_pinmux_init(void);
-extern void r8a7740_pm_init(void);
-
-#if defined(CONFIG_PM) && !defined(CONFIG_ARCH_MULTIPLATFORM)
-extern void __init r8a7740_init_pm_domains(void);
-#else
-static inline void r8a7740_init_pm_domains(void) {}
-#endif /* CONFIG_PM && !CONFIG_ARCH_MULTIPLATFORM */
-
-#endif /* __ASM_R8A7740_H__ */
diff --git a/arch/arm/mach-shmobile/setup-r8a7740.c b/arch/arm/mach-shmobile/setup-r8a7740.c
index 9832e48396a40a92..a6009ea79bd8b0aa 100644
--- a/arch/arm/mach-shmobile/setup-r8a7740.c
+++ b/arch/arm/mach-shmobile/setup-r8a7740.c
@@ -14,31 +14,19 @@
* GNU General Public License for more details.
*/
#include <linux/delay.h>
-#include <linux/dma-mapping.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-gic.h>
-#include <linux/platform_data/irq-renesas-intc-irqpin.h>
-#include <linux/platform_device.h>
#include <linux/of_platform.h>
-#include <linux/serial_sci.h>
-#include <linux/sh_dma.h>
-#include <linux/sh_timer.h>
-#include <linux/platform_data/sh_ipmmu.h>
-#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/hardware/cache-l2x0.h>
#include "common.h"
-#include "dma-register.h"
-#include "irqs.h"
-#include "pm-rmobile.h"
-#include "r8a7740.h"
static struct map_desc r8a7740_io_desc[] __initdata = {
/*
@@ -65,613 +53,12 @@ static struct map_desc r8a7740_io_desc[] __initdata = {
#endif
};
-void __init r8a7740_map_io(void)
+static void __init r8a7740_map_io(void)
{
debug_ll_io_init();
iotable_init(r8a7740_io_desc, ARRAY_SIZE(r8a7740_io_desc));
}
-/* PFC */
-static const struct resource pfc_resources[] = {
- DEFINE_RES_MEM(0xe6050000, 0x8000),
- DEFINE_RES_MEM(0xe605800c, 0x0020),
-};
-
-void __init r8a7740_pinmux_init(void)
-{
- platform_device_register_simple("pfc-r8a7740", -1, pfc_resources,
- ARRAY_SIZE(pfc_resources));
-}
-
-static struct renesas_intc_irqpin_config irqpin0_platform_data = {
- .irq_base = irq_pin(0), /* IRQ0 -> IRQ7 */
-};
-
-static struct resource irqpin0_resources[] = {
- DEFINE_RES_MEM(0xe6900000, 4), /* ICR1A */
- DEFINE_RES_MEM(0xe6900010, 4), /* INTPRI00A */
- DEFINE_RES_MEM(0xe6900020, 1), /* INTREQ00A */
- DEFINE_RES_MEM(0xe6900040, 1), /* INTMSK00A */
- DEFINE_RES_MEM(0xe6900060, 1), /* INTMSKCLR00A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ0 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ1 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ2 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ3 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ4 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ5 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ6 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ7 */
-};
-
-static struct platform_device irqpin0_device = {
- .name = "renesas_intc_irqpin",
- .id = 0,
- .resource = irqpin0_resources,
- .num_resources = ARRAY_SIZE(irqpin0_resources),
- .dev = {
- .platform_data = &irqpin0_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin1_platform_data = {
- .irq_base = irq_pin(8), /* IRQ8 -> IRQ15 */
-};
-
-static struct resource irqpin1_resources[] = {
- DEFINE_RES_MEM(0xe6900004, 4), /* ICR2A */
- DEFINE_RES_MEM(0xe6900014, 4), /* INTPRI10A */
- DEFINE_RES_MEM(0xe6900024, 1), /* INTREQ10A */
- DEFINE_RES_MEM(0xe6900044, 1), /* INTMSK10A */
- DEFINE_RES_MEM(0xe6900064, 1), /* INTMSKCLR10A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ8 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ9 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ10 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ11 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ12 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ13 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ14 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ15 */
-};
-
-static struct platform_device irqpin1_device = {
- .name = "renesas_intc_irqpin",
- .id = 1,
- .resource = irqpin1_resources,
- .num_resources = ARRAY_SIZE(irqpin1_resources),
- .dev = {
- .platform_data = &irqpin1_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin2_platform_data = {
- .irq_base = irq_pin(16), /* IRQ16 -> IRQ23 */
-};
-
-static struct resource irqpin2_resources[] = {
- DEFINE_RES_MEM(0xe6900008, 4), /* ICR3A */
- DEFINE_RES_MEM(0xe6900018, 4), /* INTPRI30A */
- DEFINE_RES_MEM(0xe6900028, 1), /* INTREQ30A */
- DEFINE_RES_MEM(0xe6900048, 1), /* INTMSK30A */
- DEFINE_RES_MEM(0xe6900068, 1), /* INTMSKCLR30A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ16 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ17 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ18 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ19 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ20 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ21 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ22 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ23 */
-};
-
-static struct platform_device irqpin2_device = {
- .name = "renesas_intc_irqpin",
- .id = 2,
- .resource = irqpin2_resources,
- .num_resources = ARRAY_SIZE(irqpin2_resources),
- .dev = {
- .platform_data = &irqpin2_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin3_platform_data = {
- .irq_base = irq_pin(24), /* IRQ24 -> IRQ31 */
-};
-
-static struct resource irqpin3_resources[] = {
- DEFINE_RES_MEM(0xe690000c, 4), /* ICR3A */
- DEFINE_RES_MEM(0xe690001c, 4), /* INTPRI30A */
- DEFINE_RES_MEM(0xe690002c, 1), /* INTREQ30A */
- DEFINE_RES_MEM(0xe690004c, 1), /* INTMSK30A */
- DEFINE_RES_MEM(0xe690006c, 1), /* INTMSKCLR30A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ24 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ25 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ26 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ27 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ28 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ29 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ30 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ31 */
-};
-
-static struct platform_device irqpin3_device = {
- .name = "renesas_intc_irqpin",
- .id = 3,
- .resource = irqpin3_resources,
- .num_resources = ARRAY_SIZE(irqpin3_resources),
- .dev = {
- .platform_data = &irqpin3_platform_data,
- },
-};
-
-/* SCIF */
-#define R8A7740_SCIF(scif_type, index, baseaddr, irq) \
-static struct plat_sci_port scif##index##_platform_data = { \
- .type = scif_type, \
- .flags = UPF_BOOT_AUTOCONF, \
- .scscr = SCSCR_RE | SCSCR_TE, \
-}; \
- \
-static struct resource scif##index##_resources[] = { \
- DEFINE_RES_MEM(baseaddr, 0x100), \
- DEFINE_RES_IRQ(irq), \
-}; \
- \
-static struct platform_device scif##index##_device = { \
- .name = "sh-sci", \
- .id = index, \
- .resource = scif##index##_resources, \
- .num_resources = ARRAY_SIZE(scif##index##_resources), \
- .dev = { \
- .platform_data = &scif##index##_platform_data, \
- }, \
-}
-
-R8A7740_SCIF(PORT_SCIFA, 0, 0xe6c40000, gic_spi(100));
-R8A7740_SCIF(PORT_SCIFA, 1, 0xe6c50000, gic_spi(101));
-R8A7740_SCIF(PORT_SCIFA, 2, 0xe6c60000, gic_spi(102));
-R8A7740_SCIF(PORT_SCIFA, 3, 0xe6c70000, gic_spi(103));
-R8A7740_SCIF(PORT_SCIFA, 4, 0xe6c80000, gic_spi(104));
-R8A7740_SCIF(PORT_SCIFA, 5, 0xe6cb0000, gic_spi(105));
-R8A7740_SCIF(PORT_SCIFA, 6, 0xe6cc0000, gic_spi(106));
-R8A7740_SCIF(PORT_SCIFA, 7, 0xe6cd0000, gic_spi(107));
-R8A7740_SCIF(PORT_SCIFB, 8, 0xe6c30000, gic_spi(108));
-
-/* CMT */
-static struct sh_timer_config cmt1_platform_data = {
- .channels_mask = 0x3f,
-};
-
-static struct resource cmt1_resources[] = {
- DEFINE_RES_MEM(0xe6138000, 0x170),
- DEFINE_RES_IRQ(gic_spi(58)),
-};
-
-static struct platform_device cmt1_device = {
- .name = "sh-cmt-48",
- .id = 1,
- .dev = {
- .platform_data = &cmt1_platform_data,
- },
- .resource = cmt1_resources,
- .num_resources = ARRAY_SIZE(cmt1_resources),
-};
-
-/* TMU */
-static struct sh_timer_config tmu0_platform_data = {
- .channels_mask = 7,
-};
-
-static struct resource tmu0_resources[] = {
- DEFINE_RES_MEM(0xfff80000, 0x2c),
- DEFINE_RES_IRQ(gic_spi(198)),
- DEFINE_RES_IRQ(gic_spi(199)),
- DEFINE_RES_IRQ(gic_spi(200)),
-};
-
-static struct platform_device tmu0_device = {
- .name = "sh-tmu",
- .id = 0,
- .dev = {
- .platform_data = &tmu0_platform_data,
- },
- .resource = tmu0_resources,
- .num_resources = ARRAY_SIZE(tmu0_resources),
-};
-
-/* IPMMUI (an IPMMU module for ICB/LMB) */
-static struct resource ipmmu_resources[] = {
- [0] = {
- .name = "IPMMUI",
- .start = 0xfe951000,
- .end = 0xfe9510ff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static const char * const ipmmu_dev_names[] = {
- "sh_mobile_lcdc_fb.0",
- "sh_mobile_lcdc_fb.1",
- "sh_mobile_ceu.0",
-};
-
-static struct shmobile_ipmmu_platform_data ipmmu_platform_data = {
- .dev_names = ipmmu_dev_names,
- .num_dev_names = ARRAY_SIZE(ipmmu_dev_names),
-};
-
-static struct platform_device ipmmu_device = {
- .name = "ipmmu",
- .id = -1,
- .dev = {
- .platform_data = &ipmmu_platform_data,
- },
- .resource = ipmmu_resources,
- .num_resources = ARRAY_SIZE(ipmmu_resources),
-};
-
-static struct platform_device *r8a7740_early_devices[] __initdata = {
- &scif0_device,
- &scif1_device,
- &scif2_device,
- &scif3_device,
- &scif4_device,
- &scif5_device,
- &scif6_device,
- &scif7_device,
- &scif8_device,
- &irqpin0_device,
- &irqpin1_device,
- &irqpin2_device,
- &irqpin3_device,
- &tmu0_device,
- &ipmmu_device,
- &cmt1_device,
-};
-
-/* DMA */
-static const struct sh_dmae_slave_config r8a7740_dmae_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_SDHI0_TX,
- .addr = 0xe6850030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc1,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI0_RX,
- .addr = 0xe6850030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xc2,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_TX,
- .addr = 0xe6860030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc9,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_RX,
- .addr = 0xe6860030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xca,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_TX,
- .addr = 0xe6870030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xcd,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_RX,
- .addr = 0xe6870030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xce,
- }, {
- .slave_id = SHDMA_SLAVE_FSIA_TX,
- .addr = 0xfe1f0024,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xb1,
- }, {
- .slave_id = SHDMA_SLAVE_FSIA_RX,
- .addr = 0xfe1f0020,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xb2,
- }, {
- .slave_id = SHDMA_SLAVE_FSIB_TX,
- .addr = 0xfe1f0064,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xb5,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_TX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd1,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_RX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xd2,
- },
-};
-
-#define DMA_CHANNEL(a, b, c) \
-{ \
- .offset = a, \
- .dmars = b, \
- .dmars_bit = c, \
- .chclr_offset = (0x220 - 0x20) + a \
-}
-
-static const struct sh_dmae_channel r8a7740_dmae_channels[] = {
- DMA_CHANNEL(0x00, 0, 0),
- DMA_CHANNEL(0x10, 0, 8),
- DMA_CHANNEL(0x20, 4, 0),
- DMA_CHANNEL(0x30, 4, 8),
- DMA_CHANNEL(0x50, 8, 0),
- DMA_CHANNEL(0x60, 8, 8),
-};
-
-static struct sh_dmae_pdata dma_platform_data = {
- .slave = r8a7740_dmae_slaves,
- .slave_num = ARRAY_SIZE(r8a7740_dmae_slaves),
- .channel = r8a7740_dmae_channels,
- .channel_num = ARRAY_SIZE(r8a7740_dmae_channels),
- .ts_low_shift = TS_LOW_SHIFT,
- .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
- .ts_high_shift = TS_HI_SHIFT,
- .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
- .ts_shift = dma_ts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
- .dmaor_init = DMAOR_DME,
- .chclr_present = 1,
-};
-
-/* Resource order important! */
-static struct resource r8a7740_dmae0_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xfe008020,
- .end = 0xfe00828f,
- .flags = IORESOURCE_MEM,
- },
- {
- /* DMARSx */
- .start = 0xfe009000,
- .end = 0xfe00900b,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "error_irq",
- .start = gic_spi(34),
- .end = gic_spi(34),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(28),
- .end = gic_spi(33),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-/* Resource order important! */
-static struct resource r8a7740_dmae1_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xfe018020,
- .end = 0xfe01828f,
- .flags = IORESOURCE_MEM,
- },
- {
- /* DMARSx */
- .start = 0xfe019000,
- .end = 0xfe01900b,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "error_irq",
- .start = gic_spi(41),
- .end = gic_spi(41),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(35),
- .end = gic_spi(40),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-/* Resource order important! */
-static struct resource r8a7740_dmae2_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xfe028020,
- .end = 0xfe02828f,
- .flags = IORESOURCE_MEM,
- },
- {
- /* DMARSx */
- .start = 0xfe029000,
- .end = 0xfe02900b,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "error_irq",
- .start = gic_spi(48),
- .end = gic_spi(48),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(42),
- .end = gic_spi(47),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device dma0_device = {
- .name = "sh-dma-engine",
- .id = 0,
- .resource = r8a7740_dmae0_resources,
- .num_resources = ARRAY_SIZE(r8a7740_dmae0_resources),
- .dev = {
- .platform_data = &dma_platform_data,
- },
-};
-
-static struct platform_device dma1_device = {
- .name = "sh-dma-engine",
- .id = 1,
- .resource = r8a7740_dmae1_resources,
- .num_resources = ARRAY_SIZE(r8a7740_dmae1_resources),
- .dev = {
- .platform_data = &dma_platform_data,
- },
-};
-
-static struct platform_device dma2_device = {
- .name = "sh-dma-engine",
- .id = 2,
- .resource = r8a7740_dmae2_resources,
- .num_resources = ARRAY_SIZE(r8a7740_dmae2_resources),
- .dev = {
- .platform_data = &dma_platform_data,
- },
-};
-
-/* USB-DMAC */
-static const struct sh_dmae_channel r8a7740_usb_dma_channels[] = {
- {
- .offset = 0,
- }, {
- .offset = 0x20,
- },
-};
-
-static const struct sh_dmae_slave_config r8a7740_usb_dma_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_USBHS_TX,
- .chcr = USBTS_INDEX2VAL(USBTS_XMIT_SZ_8BYTE),
- }, {
- .slave_id = SHDMA_SLAVE_USBHS_RX,
- .chcr = USBTS_INDEX2VAL(USBTS_XMIT_SZ_8BYTE),
- },
-};
-
-static struct sh_dmae_pdata usb_dma_platform_data = {
- .slave = r8a7740_usb_dma_slaves,
- .slave_num = ARRAY_SIZE(r8a7740_usb_dma_slaves),
- .channel = r8a7740_usb_dma_channels,
- .channel_num = ARRAY_SIZE(r8a7740_usb_dma_channels),
- .ts_low_shift = USBTS_LOW_SHIFT,
- .ts_low_mask = USBTS_LOW_BIT << USBTS_LOW_SHIFT,
- .ts_high_shift = USBTS_HI_SHIFT,
- .ts_high_mask = USBTS_HI_BIT << USBTS_HI_SHIFT,
- .ts_shift = dma_usbts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_usbts_shift),
- .dmaor_init = DMAOR_DME,
- .chcr_offset = 0x14,
- .chcr_ie_bit = 1 << 5,
- .dmaor_is_32bit = 1,
- .needs_tend_set = 1,
- .no_dmars = 1,
- .slave_only = 1,
-};
-
-static struct resource r8a7740_usb_dma_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xe68a0020,
- .end = 0xe68a0064 - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- /* VCR/SWR/DMICR */
- .start = 0xe68a0000,
- .end = 0xe68a0014 - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- /* IRQ for channels */
- .start = gic_spi(49),
- .end = gic_spi(49),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usb_dma_device = {
- .name = "sh-dma-engine",
- .id = 3,
- .resource = r8a7740_usb_dma_resources,
- .num_resources = ARRAY_SIZE(r8a7740_usb_dma_resources),
- .dev = {
- .platform_data = &usb_dma_platform_data,
- },
-};
-
-/* I2C */
-static struct resource i2c0_resources[] = {
- [0] = {
- .name = "IIC0",
- .start = 0xfff20000,
- .end = 0xfff20425 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(201),
- .end = gic_spi(204),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- [0] = {
- .name = "IIC1",
- .start = 0xe6c20000,
- .end = 0xe6c20425 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(70), /* IIC1_ALI1 */
- .end = gic_spi(73), /* IIC1_DTEI1 */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device i2c0_device = {
- .name = "i2c-sh_mobile",
- .id = 0,
- .resource = i2c0_resources,
- .num_resources = ARRAY_SIZE(i2c0_resources),
-};
-
-static struct platform_device i2c1_device = {
- .name = "i2c-sh_mobile",
- .id = 1,
- .resource = i2c1_resources,
- .num_resources = ARRAY_SIZE(i2c1_resources),
-};
-
-static struct resource pmu_resources[] = {
- [0] = {
- .start = gic_spi(83),
- .end = gic_spi(83),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device pmu_device = {
- .name = "armv7-pmu",
- .id = -1,
- .num_resources = ARRAY_SIZE(pmu_resources),
- .resource = pmu_resources,
-};
-
-static struct platform_device *r8a7740_late_devices[] __initdata = {
- &i2c0_device,
- &i2c1_device,
- &dma0_device,
- &dma1_device,
- &dma2_device,
- &usb_dma_device,
- &pmu_device,
-};
-
/*
* r8a7740 chip has lasting errata on MERAM buffer.
* this is work-around for it.
@@ -679,7 +66,7 @@ static struct platform_device *r8a7740_late_devices[] __initdata = {
* "Media RAM (MERAM)" on r8a7740 documentation
*/
#define MEBUFCNTR 0xFE950098
-void __init r8a7740_meram_workaround(void)
+static void __init r8a7740_meram_workaround(void)
{
void __iomem *reg;
@@ -690,124 +77,13 @@ void __init r8a7740_meram_workaround(void)
}
}
-#define ICCR 0x0004
-#define ICSTART 0x0070
-
-#define i2c_read(reg, offset) ioread8(reg + offset)
-#define i2c_write(reg, offset, data) iowrite8(data, reg + offset)
-
-/*
- * r8a7740 chip has lasting errata on I2C I/O pad reset.
- * this is work-around for it.
- */
-static void r8a7740_i2c_workaround(struct platform_device *pdev)
-{
- struct resource *res;
- void __iomem *reg;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (unlikely(!res)) {
- pr_err("r8a7740 i2c workaround fail (cannot find resource)\n");
- return;
- }
-
- reg = ioremap(res->start, resource_size(res));
- if (unlikely(!reg)) {
- pr_err("r8a7740 i2c workaround fail (cannot map IO)\n");
- return;
- }
-
- i2c_write(reg, ICCR, i2c_read(reg, ICCR) | 0x80);
- i2c_read(reg, ICCR); /* dummy read */
-
- i2c_write(reg, ICSTART, i2c_read(reg, ICSTART) | 0x10);
- i2c_read(reg, ICSTART); /* dummy read */
-
- udelay(10);
-
- i2c_write(reg, ICCR, 0x01);
- i2c_write(reg, ICSTART, 0x00);
-
- udelay(10);
-
- i2c_write(reg, ICCR, 0x10);
- udelay(10);
- i2c_write(reg, ICCR, 0x00);
- udelay(10);
- i2c_write(reg, ICCR, 0x10);
- udelay(10);
-
- iounmap(reg);
-}
-
-void __init r8a7740_add_standard_devices(void)
-{
- static struct pm_domain_device domain_devices[] __initdata = {
- { "A4R", &tmu0_device },
- { "A4R", &i2c0_device },
- { "A4S", &irqpin0_device },
- { "A4S", &irqpin1_device },
- { "A4S", &irqpin2_device },
- { "A4S", &irqpin3_device },
- { "A3SP", &scif0_device },
- { "A3SP", &scif1_device },
- { "A3SP", &scif2_device },
- { "A3SP", &scif3_device },
- { "A3SP", &scif4_device },
- { "A3SP", &scif5_device },
- { "A3SP", &scif6_device },
- { "A3SP", &scif7_device },
- { "A3SP", &scif8_device },
- { "A3SP", &i2c1_device },
- { "A3SP", &ipmmu_device },
- { "A3SP", &dma0_device },
- { "A3SP", &dma1_device },
- { "A3SP", &dma2_device },
- { "A3SP", &usb_dma_device },
- };
-
- /* I2C work-around */
- r8a7740_i2c_workaround(&i2c0_device);
- r8a7740_i2c_workaround(&i2c1_device);
-
- r8a7740_init_pm_domains();
-
- /* add devices */
- platform_add_devices(r8a7740_early_devices,
- ARRAY_SIZE(r8a7740_early_devices));
- platform_add_devices(r8a7740_late_devices,
- ARRAY_SIZE(r8a7740_late_devices));
-
- /* add devices to PM domain */
- rmobile_add_devices_to_domains(domain_devices,
- ARRAY_SIZE(domain_devices));
-}
-
-void __init r8a7740_add_early_devices(void)
-{
- early_platform_add_devices(r8a7740_early_devices,
- ARRAY_SIZE(r8a7740_early_devices));
-
- /* setup early console here as well */
- shmobile_setup_console();
-}
-
-#ifdef CONFIG_USE_OF
-
-void __init r8a7740_init_irq_of(void)
+static void __init r8a7740_init_irq_of(void)
{
void __iomem *intc_prio_base = ioremap_nocache(0xe6900010, 0x10);
void __iomem *intc_msk_base = ioremap_nocache(0xe6900040, 0x10);
void __iomem *pfc_inta_ctrl = ioremap_nocache(0xe605807c, 0x4);
-#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
- void __iomem *gic_dist_base = ioremap_nocache(0xc2800000, 0x1000);
- void __iomem *gic_cpu_base = ioremap_nocache(0xc2000000, 0x1000);
-
- gic_init(0, 29, gic_dist_base, gic_cpu_base);
-#else
irqchip_init();
-#endif
/* route signals to GIC */
iowrite32(0x0, pfc_inta_ctrl);
@@ -855,5 +131,3 @@ DT_MACHINE_START(R8A7740_DT, "Generic R8A7740 (Flattened Device Tree)")
.init_late = shmobile_init_late,
.dt_compat = r8a7740_boards_compat_dt,
MACHINE_END
-
-#endif /* CONFIG_USE_OF */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 08/15] ARM: shmobile: Remove legacy SoC code for R-Mobile A1
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the R-Mobile A1 (r8a7740) legacy SoC code was the
Armadillo-800 EVA legacy board code, which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/Kconfig | 7 -
arch/arm/mach-shmobile/Makefile | 3 +-
arch/arm/mach-shmobile/clock-r8a7740.c | 675 ------------------------------
arch/arm/mach-shmobile/pm-r8a7740.c | 129 ------
arch/arm/mach-shmobile/r8a7740.h | 58 ---
arch/arm/mach-shmobile/setup-r8a7740.c | 732 +--------------------------------
6 files changed, 4 insertions(+), 1600 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/clock-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/pm-r8a7740.c
delete mode 100644 arch/arm/mach-shmobile/r8a7740.h
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index e256c6b664710099..050bcd504458f6f0 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -108,13 +108,6 @@ if ARCH_SHMOBILE_LEGACY
comment "Renesas ARM SoCs System Type"
-config ARCH_R8A7740
- bool "R-Mobile A1 (R8A77400)"
- select ARCH_RMOBILE
- select ARCH_WANT_OPTIONAL_GPIOLIB
- select ARM_GIC
- select RENESAS_INTC_IRQPIN
-
config ARCH_R8A7778
bool "R-Car M1A (R8A77781)"
select ARCH_RCAR_GEN1
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 4ffd7428353b53f9..6cb095107f905d02 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -8,7 +8,7 @@ obj-y := timer.o console.o
# CPU objects
obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o
obj-$(CONFIG_ARCH_R8A73A4) += setup-r8a73a4.o
-obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o pm-r8a7740.o
+obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += setup-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += setup-r8a7779.o pm-r8a7779.o
obj-$(CONFIG_ARCH_R8A7790) += setup-r8a7790.o
@@ -21,7 +21,6 @@ obj-$(CONFIG_ARCH_R7S72100) += setup-r7s72100.o
# Clock objects
ifndef CONFIG_COMMON_CLK
obj-y += clock.o
-obj-$(CONFIG_ARCH_R8A7740) += clock-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += clock-r8a7778.o
obj-$(CONFIG_ARCH_R8A7779) += clock-r8a7779.o
endif
diff --git a/arch/arm/mach-shmobile/clock-r8a7740.c b/arch/arm/mach-shmobile/clock-r8a7740.c
deleted file mode 100644
index 9cac8247c72b6e45..0000000000000000
--- a/arch/arm/mach-shmobile/clock-r8a7740.c
+++ /dev/null
@@ -1,675 +0,0 @@
-/*
- * R8A7740 processor support
- *
- * Copyright (C) 2011 Renesas Solutions Corp.
- * Copyright (C) 2011 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/sh_clk.h>
-#include <linux/clkdev.h>
-
-#include "clock.h"
-#include "common.h"
-#include "r8a7740.h"
-
-/*
- * | MDx | XTAL1/EXTAL1 | System | EXTALR |
- * Clock |-------+-----------------+ clock | 32.768 | RCLK
- * Mode | 2/1/0 | src MHz | source | KHz | source
- * -------+-------+-----------------+-----------+--------+----------
- * 0 | 0 0 0 | External 20~50 | XTAL1 | O | EXTALR
- * 1 | 0 0 1 | Crystal 20~30 | XTAL1 | O | EXTALR
- * 2 | 0 1 0 | External 40~50 | XTAL1 / 2 | O | EXTALR
- * 3 | 0 1 1 | Crystal 40~50 | XTAL1 / 2 | O | EXTALR
- * 4 | 1 0 0 | External 20~50 | XTAL1 | x | XTAL1 / 1024
- * 5 | 1 0 1 | Crystal 20~30 | XTAL1 | x | XTAL1 / 1024
- * 6 | 1 1 0 | External 40~50 | XTAL1 / 2 | x | XTAL1 / 2048
- * 7 | 1 1 1 | Crystal 40~50 | XTAL1 / 2 | x | XTAL1 / 2048
- */
-
-/* CPG registers */
-#define FRQCRA IOMEM(0xe6150000)
-#define FRQCRB IOMEM(0xe6150004)
-#define VCLKCR1 IOMEM(0xE6150008)
-#define VCLKCR2 IOMEM(0xE615000c)
-#define FRQCRC IOMEM(0xe61500e0)
-#define FSIACKCR IOMEM(0xe6150018)
-#define PLLC01CR IOMEM(0xe6150028)
-
-#define SUBCKCR IOMEM(0xe6150080)
-#define USBCKCR IOMEM(0xe615008c)
-
-#define MSTPSR0 IOMEM(0xe6150030)
-#define MSTPSR1 IOMEM(0xe6150038)
-#define MSTPSR2 IOMEM(0xe6150040)
-#define MSTPSR3 IOMEM(0xe6150048)
-#define MSTPSR4 IOMEM(0xe615004c)
-#define FSIBCKCR IOMEM(0xe6150090)
-#define HDMICKCR IOMEM(0xe6150094)
-#define SMSTPCR0 IOMEM(0xe6150130)
-#define SMSTPCR1 IOMEM(0xe6150134)
-#define SMSTPCR2 IOMEM(0xe6150138)
-#define SMSTPCR3 IOMEM(0xe615013c)
-#define SMSTPCR4 IOMEM(0xe6150140)
-
-#define FSIDIVA IOMEM(0xFE1F8000)
-#define FSIDIVB IOMEM(0xFE1F8008)
-
-/* Fixed 32 KHz root clock from EXTALR pin */
-static struct clk extalr_clk = {
- .rate = 32768,
-};
-
-/*
- * 25MHz default rate for the EXTAL1 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-static struct clk extal1_clk = {
- .rate = 25000000,
-};
-
-/*
- * 48MHz default rate for the EXTAL2 root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-static struct clk extal2_clk = {
- .rate = 48000000,
-};
-
-/*
- * 27MHz default rate for the DV_CLKI root input clock.
- * If needed, reset this with clk_set_rate() from the platform code.
- */
-static struct clk dv_clk = {
- .rate = 27000000,
-};
-
-SH_CLK_RATIO(div2, 1, 2);
-SH_CLK_RATIO(div1k, 1, 1024);
-
-SH_FIXED_RATIO_CLK(extal1_div2_clk, extal1_clk, div2);
-SH_FIXED_RATIO_CLK(extal1_div1024_clk, extal1_clk, div1k);
-SH_FIXED_RATIO_CLK(extal1_div2048_clk, extal1_div2_clk, div1k);
-SH_FIXED_RATIO_CLK(extal2_div2_clk, extal2_clk, div2);
-
-static struct sh_clk_ops followparent_clk_ops = {
- .recalc = followparent_recalc,
-};
-
-/* Main clock */
-static struct clk system_clk = {
- .ops = &followparent_clk_ops,
-};
-
-SH_FIXED_RATIO_CLK(system_div2_clk, system_clk, div2);
-
-/* r_clk */
-static struct clk r_clk = {
- .ops = &followparent_clk_ops,
-};
-
-/* PLLC0/PLLC1 */
-static unsigned long pllc01_recalc(struct clk *clk)
-{
- unsigned long mult = 1;
-
- if (__raw_readl(PLLC01CR) & (1 << 14))
- mult = ((__raw_readl(clk->enable_reg) >> 24) & 0x7f) + 1;
-
- return clk->parent->rate * mult;
-}
-
-static struct sh_clk_ops pllc01_clk_ops = {
- .recalc = pllc01_recalc,
-};
-
-static struct clk pllc0_clk = {
- .ops = &pllc01_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &system_clk,
- .enable_reg = (void __iomem *)FRQCRC,
-};
-
-static struct clk pllc1_clk = {
- .ops = &pllc01_clk_ops,
- .flags = CLK_ENABLE_ON_INIT,
- .parent = &system_div2_clk,
- .enable_reg = (void __iomem *)FRQCRA,
-};
-
-/* PLLC1 / 2 */
-SH_FIXED_RATIO_CLK(pllc1_div2_clk, pllc1_clk, div2);
-
-/* USB clock */
-/*
- * USBCKCR is controlling usb24 clock
- * bit[7] : parent clock
- * bit[6] : clock divide rate
- * And this bit[7] is used as a "usb24s" from other devices.
- * (Video clock / Sub clock / SPU clock)
- * You can controll this clock as a below.
- *
- * struct clk *usb24 = clk_get(dev, "usb24");
- * struct clk *usb24s = clk_get(NULL, "usb24s");
- * struct clk *system = clk_get(NULL, "system_clk");
- * int rate = clk_get_rate(system);
- *
- * clk_set_parent(usb24s, system); // for bit[7]
- * clk_set_rate(usb24, rate / 2); // for bit[6]
- */
-static struct clk *usb24s_parents[] = {
- [0] = &system_clk,
- [1] = &extal2_clk
-};
-
-static int usb24s_enable(struct clk *clk)
-{
- __raw_writel(__raw_readl(USBCKCR) & ~(1 << 8), USBCKCR);
-
- return 0;
-}
-
-static void usb24s_disable(struct clk *clk)
-{
- __raw_writel(__raw_readl(USBCKCR) | (1 << 8), USBCKCR);
-}
-
-static int usb24s_set_parent(struct clk *clk, struct clk *parent)
-{
- int i, ret;
- u32 val;
-
- if (!clk->parent_table || !clk->parent_num)
- return -EINVAL;
-
- /* Search the parent */
- for (i = 0; i < clk->parent_num; i++)
- if (clk->parent_table[i] == parent)
- break;
-
- if (i == clk->parent_num)
- return -ENODEV;
-
- ret = clk_reparent(clk, parent);
- if (ret < 0)
- return ret;
-
- val = __raw_readl(USBCKCR);
- val &= ~(1 << 7);
- val |= i << 7;
- __raw_writel(val, USBCKCR);
-
- return 0;
-}
-
-static struct sh_clk_ops usb24s_clk_ops = {
- .recalc = followparent_recalc,
- .enable = usb24s_enable,
- .disable = usb24s_disable,
- .set_parent = usb24s_set_parent,
-};
-
-static struct clk usb24s_clk = {
- .ops = &usb24s_clk_ops,
- .parent_table = usb24s_parents,
- .parent_num = ARRAY_SIZE(usb24s_parents),
- .parent = &system_clk,
-};
-
-static unsigned long usb24_recalc(struct clk *clk)
-{
- return clk->parent->rate /
- ((__raw_readl(USBCKCR) & (1 << 6)) ? 1 : 2);
-};
-
-static int usb24_set_rate(struct clk *clk, unsigned long rate)
-{
- u32 val;
-
- /* closer to which ? parent->rate or parent->rate/2 */
- val = __raw_readl(USBCKCR);
- val &= ~(1 << 6);
- val |= (rate > (clk->parent->rate / 4) * 3) << 6;
- __raw_writel(val, USBCKCR);
-
- return 0;
-}
-
-static struct sh_clk_ops usb24_clk_ops = {
- .recalc = usb24_recalc,
- .set_rate = usb24_set_rate,
-};
-
-static struct clk usb24_clk = {
- .ops = &usb24_clk_ops,
- .parent = &usb24s_clk,
-};
-
-/* External FSIACK/FSIBCK clock */
-static struct clk fsiack_clk = {
-};
-
-static struct clk fsibck_clk = {
-};
-
-static struct clk *main_clks[] = {
- &extalr_clk,
- &extal1_clk,
- &extal2_clk,
- &extal1_div2_clk,
- &extal1_div1024_clk,
- &extal1_div2048_clk,
- &extal2_div2_clk,
- &dv_clk,
- &system_clk,
- &system_div2_clk,
- &r_clk,
- &pllc0_clk,
- &pllc1_clk,
- &pllc1_div2_clk,
- &usb24s_clk,
- &usb24_clk,
- &fsiack_clk,
- &fsibck_clk,
-};
-
-/* DIV4 clocks */
-static void div4_kick(struct clk *clk)
-{
- unsigned long value;
-
- /* set KICK bit in FRQCRB to update hardware setting */
- value = __raw_readl(FRQCRB);
- value |= (1 << 31);
- __raw_writel(value, FRQCRB);
-}
-
-static int divisors[] = { 2, 3, 4, 6, 8, 12, 16, 18,
- 24, 32, 36, 48, 0, 72, 96, 0 };
-
-static struct clk_div_mult_table div4_div_mult_table = {
- .divisors = divisors,
- .nr_divisors = ARRAY_SIZE(divisors),
-};
-
-static struct clk_div4_table div4_table = {
- .div_mult_table = &div4_div_mult_table,
- .kick = div4_kick,
-};
-
-enum {
- DIV4_I, DIV4_ZG, DIV4_B, DIV4_M1, DIV4_HP,
- DIV4_HPP, DIV4_USBP, DIV4_S, DIV4_ZB, DIV4_M3, DIV4_CP,
- DIV4_NR
-};
-
-static struct clk div4_clks[DIV4_NR] = {
- [DIV4_I] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 20, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_ZG] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 16, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_B] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 8, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_M1] = SH_CLK_DIV4(&pllc1_clk, FRQCRA, 4, 0x6fff, CLK_ENABLE_ON_INIT),
- [DIV4_HP] = SH_CLK_DIV4(&pllc1_clk, FRQCRB, 4, 0x6fff, 0),
- [DIV4_HPP] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 20, 0x6fff, 0),
- [DIV4_USBP] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 16, 0x6fff, 0),
- [DIV4_S] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 12, 0x6fff, 0),
- [DIV4_ZB] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 8, 0x6fff, 0),
- [DIV4_M3] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 4, 0x6fff, 0),
- [DIV4_CP] = SH_CLK_DIV4(&pllc1_clk, FRQCRC, 0, 0x6fff, 0),
-};
-
-/* DIV6 reparent */
-enum {
- DIV6_HDMI,
- DIV6_VCLK1, DIV6_VCLK2,
- DIV6_FSIA, DIV6_FSIB,
- DIV6_REPARENT_NR,
-};
-
-static struct clk *hdmi_parent[] = {
- [0] = &pllc1_div2_clk,
- [1] = &system_clk,
- [2] = &dv_clk
-};
-
-static struct clk *vclk_parents[8] = {
- [0] = &pllc1_div2_clk,
- [2] = &dv_clk,
- [3] = &usb24s_clk,
- [4] = &extal1_div2_clk,
- [5] = &extalr_clk,
-};
-
-static struct clk *fsia_parents[] = {
- [0] = &pllc1_div2_clk,
- [1] = &fsiack_clk, /* external clock */
-};
-
-static struct clk *fsib_parents[] = {
- [0] = &pllc1_div2_clk,
- [1] = &fsibck_clk, /* external clock */
-};
-
-static struct clk div6_reparent_clks[DIV6_REPARENT_NR] = {
- [DIV6_HDMI] = SH_CLK_DIV6_EXT(HDMICKCR, 0,
- hdmi_parent, ARRAY_SIZE(hdmi_parent), 6, 2),
- [DIV6_VCLK1] = SH_CLK_DIV6_EXT(VCLKCR1, 0,
- vclk_parents, ARRAY_SIZE(vclk_parents), 12, 3),
- [DIV6_VCLK2] = SH_CLK_DIV6_EXT(VCLKCR2, 0,
- vclk_parents, ARRAY_SIZE(vclk_parents), 12, 3),
- [DIV6_FSIA] = SH_CLK_DIV6_EXT(FSIACKCR, 0,
- fsia_parents, ARRAY_SIZE(fsia_parents), 6, 2),
- [DIV6_FSIB] = SH_CLK_DIV6_EXT(FSIBCKCR, 0,
- fsib_parents, ARRAY_SIZE(fsib_parents), 6, 2),
-};
-
-/* DIV6 clocks */
-enum {
- DIV6_SUB,
- DIV6_NR
-};
-
-static struct clk div6_clks[DIV6_NR] = {
- [DIV6_SUB] = SH_CLK_DIV6(&pllc1_div2_clk, SUBCKCR, 0),
-};
-
-/* HDMI1/2 clock */
-static unsigned long hdmi12_recalc(struct clk *clk)
-{
- u32 val = __raw_readl(HDMICKCR);
- int shift = (int)clk->priv;
-
- val >>= shift;
- val &= 0x3;
-
- return clk->parent->rate / (1 << val);
-};
-
-static int hdmi12_set_rate(struct clk *clk, unsigned long rate)
-{
- u32 val, mask;
- int i, shift;
-
- for (i = 0; i < 3; i++)
- if (rate == clk->parent->rate / (1 << i))
- goto find;
- return -ENODEV;
-
-find:
- shift = (int)clk->priv;
-
- val = __raw_readl(HDMICKCR);
- mask = ~(0x3 << shift);
- val = (val & mask) | i << shift;
- __raw_writel(val, HDMICKCR);
-
- return 0;
-};
-
-static struct sh_clk_ops hdmi12_clk_ops = {
- .recalc = hdmi12_recalc,
- .set_rate = hdmi12_set_rate,
-};
-
-static struct clk hdmi1_clk = {
- .ops = &hdmi12_clk_ops,
- .priv = (void *)9,
- .parent = &div6_reparent_clks[DIV6_HDMI], /* late install */
-};
-
-static struct clk hdmi2_clk = {
- .ops = &hdmi12_clk_ops,
- .priv = (void *)11,
- .parent = &div6_reparent_clks[DIV6_HDMI], /* late install */
-};
-
-static struct clk *late_main_clks[] = {
- &hdmi1_clk,
- &hdmi2_clk,
-};
-
-/* FSI DIV */
-enum { FSIDIV_A, FSIDIV_B, FSIDIV_REPARENT_NR };
-
-static struct clk fsidivs[] = {
- [FSIDIV_A] = SH_CLK_FSIDIV(FSIDIVA, &div6_reparent_clks[DIV6_FSIA]),
- [FSIDIV_B] = SH_CLK_FSIDIV(FSIDIVB, &div6_reparent_clks[DIV6_FSIB]),
-};
-
-/* MSTP */
-enum {
- MSTP128, MSTP127, MSTP125,
- MSTP116, MSTP111, MSTP100, MSTP117,
-
- MSTP230, MSTP229,
- MSTP222,
- MSTP218, MSTP217, MSTP216, MSTP214,
- MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
-
- MSTP329, MSTP328, MSTP323, MSTP320,
- MSTP314, MSTP313, MSTP312,
- MSTP309, MSTP304,
-
- MSTP416, MSTP415, MSTP407, MSTP406,
-
- MSTP_NR
-};
-
-static struct clk mstp_clks[MSTP_NR] = {
- [MSTP128] = SH_CLK_MSTP32(&div4_clks[DIV4_S], SMSTPCR1, 28, 0), /* CEU21 */
- [MSTP127] = SH_CLK_MSTP32(&div4_clks[DIV4_S], SMSTPCR1, 27, 0), /* CEU20 */
- [MSTP125] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR1, 25, 0), /* TMU0 */
- [MSTP117] = SH_CLK_MSTP32(&div4_clks[DIV4_B], SMSTPCR1, 17, 0), /* LCDC1 */
- [MSTP116] = SH_CLK_MSTP32(&div4_clks[DIV4_HPP], SMSTPCR1, 16, 0), /* IIC0 */
- [MSTP111] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR1, 11, 0), /* TMU1 */
- [MSTP100] = SH_CLK_MSTP32(&div4_clks[DIV4_B], SMSTPCR1, 0, 0), /* LCDC0 */
-
- [MSTP230] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 30, 0), /* SCIFA6 */
- [MSTP229] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 29, 0), /* INTCA */
- [MSTP222] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 22, 0), /* SCIFA7 */
- [MSTP218] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* DMAC1 */
- [MSTP217] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 17, 0), /* DMAC2 */
- [MSTP216] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 16, 0), /* DMAC3 */
- [MSTP214] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR2, 14, 0), /* USBDMAC */
- [MSTP207] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */
- [MSTP206] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */
- [MSTP204] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */
- [MSTP203] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 3, 0), /* SCIFA1 */
- [MSTP202] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 2, 0), /* SCIFA2 */
- [MSTP201] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 1, 0), /* SCIFA3 */
- [MSTP200] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR2, 0, 0), /* SCIFA4 */
-
- [MSTP329] = SH_CLK_MSTP32(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */
- [MSTP328] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 28, 0), /* FSI */
- [MSTP323] = SH_CLK_MSTP32(&div6_clks[DIV6_SUB], SMSTPCR3, 23, 0), /* IIC1 */
- [MSTP320] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 20, 0), /* USBF */
- [MSTP314] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 14, 0), /* SDHI0 */
- [MSTP313] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 13, 0), /* SDHI1 */
- [MSTP312] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 12, 0), /* MMC */
- [MSTP309] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR3, 9, 0), /* GEther */
- [MSTP304] = SH_CLK_MSTP32(&div4_clks[DIV4_CP], SMSTPCR3, 4, 0), /* TPU0 */
-
- [MSTP416] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 16, 0), /* USBHOST */
- [MSTP415] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 15, 0), /* SDHI2 */
- [MSTP407] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 7, 0), /* USB-Func */
- [MSTP406] = SH_CLK_MSTP32(&div4_clks[DIV4_HP], SMSTPCR4, 6, 0), /* USB Phy */
-};
-
-static struct clk_lookup lookups[] = {
- /* main clocks */
- CLKDEV_CON_ID("extalr", &extalr_clk),
- CLKDEV_CON_ID("extal1", &extal1_clk),
- CLKDEV_CON_ID("extal2", &extal2_clk),
- CLKDEV_CON_ID("extal1_div2", &extal1_div2_clk),
- CLKDEV_CON_ID("extal1_div1024", &extal1_div1024_clk),
- CLKDEV_CON_ID("extal1_div2048", &extal1_div2048_clk),
- CLKDEV_CON_ID("extal2_div2", &extal2_div2_clk),
- CLKDEV_CON_ID("dv_clk", &dv_clk),
- CLKDEV_CON_ID("system_clk", &system_clk),
- CLKDEV_CON_ID("system_div2_clk", &system_div2_clk),
- CLKDEV_CON_ID("r_clk", &r_clk),
- CLKDEV_CON_ID("pllc0_clk", &pllc0_clk),
- CLKDEV_CON_ID("pllc1_clk", &pllc1_clk),
- CLKDEV_CON_ID("pllc1_div2_clk", &pllc1_div2_clk),
- CLKDEV_CON_ID("usb24s", &usb24s_clk),
- CLKDEV_CON_ID("hdmi1", &hdmi1_clk),
- CLKDEV_CON_ID("hdmi2", &hdmi2_clk),
- CLKDEV_CON_ID("video1", &div6_reparent_clks[DIV6_VCLK1]),
- CLKDEV_CON_ID("video2", &div6_reparent_clks[DIV6_VCLK2]),
- CLKDEV_CON_ID("fsiack", &fsiack_clk),
- CLKDEV_CON_ID("fsibck", &fsibck_clk),
-
- /* DIV4 clocks */
- CLKDEV_CON_ID("i_clk", &div4_clks[DIV4_I]),
- CLKDEV_CON_ID("zg_clk", &div4_clks[DIV4_ZG]),
- CLKDEV_CON_ID("b_clk", &div4_clks[DIV4_B]),
- CLKDEV_CON_ID("m1_clk", &div4_clks[DIV4_M1]),
- CLKDEV_CON_ID("hp_clk", &div4_clks[DIV4_HP]),
- CLKDEV_CON_ID("hpp_clk", &div4_clks[DIV4_HPP]),
- CLKDEV_CON_ID("s_clk", &div4_clks[DIV4_S]),
- CLKDEV_CON_ID("zb_clk", &div4_clks[DIV4_ZB]),
- CLKDEV_CON_ID("m3_clk", &div4_clks[DIV4_M3]),
- CLKDEV_CON_ID("cp_clk", &div4_clks[DIV4_CP]),
-
- /* DIV6 clocks */
- CLKDEV_CON_ID("sub_clk", &div6_clks[DIV6_SUB]),
-
- /* MSTP32 clocks */
- CLKDEV_DEV_ID("sh_mobile_lcdc_fb.0", &mstp_clks[MSTP100]),
- CLKDEV_DEV_ID("i2c-sh_mobile.0", &mstp_clks[MSTP116]),
- CLKDEV_DEV_ID("fff20000.i2c", &mstp_clks[MSTP116]),
- CLKDEV_DEV_ID("sh_mobile_lcdc_fb.1", &mstp_clks[MSTP117]),
- CLKDEV_DEV_ID("sh_mobile_ceu.0", &mstp_clks[MSTP127]),
- CLKDEV_DEV_ID("sh_mobile_ceu.1", &mstp_clks[MSTP128]),
-
- CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP200]),
- CLKDEV_DEV_ID("e6c80000.serial", &mstp_clks[MSTP200]),
- CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP201]),
- CLKDEV_DEV_ID("e6c70000.serial", &mstp_clks[MSTP201]),
- CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP202]),
- CLKDEV_DEV_ID("e6c60000.serial", &mstp_clks[MSTP202]),
- CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]),
- CLKDEV_DEV_ID("e6c50000.serial", &mstp_clks[MSTP203]),
- CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]),
- CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]),
- CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]),
- CLKDEV_DEV_ID("e6c30000.serial", &mstp_clks[MSTP206]),
- CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]),
- CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]),
- CLKDEV_DEV_ID("sh-dma-engine.3", &mstp_clks[MSTP214]),
- CLKDEV_DEV_ID("sh-dma-engine.2", &mstp_clks[MSTP216]),
- CLKDEV_DEV_ID("sh-dma-engine.1", &mstp_clks[MSTP217]),
- CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]),
- CLKDEV_DEV_ID("sh-sci.7", &mstp_clks[MSTP222]),
- CLKDEV_DEV_ID("e6cd0000.serial", &mstp_clks[MSTP222]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.0", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.1", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.2", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("renesas_intc_irqpin.3", &mstp_clks[MSTP229]),
- CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP230]),
- CLKDEV_DEV_ID("e6cc0000.serial", &mstp_clks[MSTP230]),
-
- CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]),
- CLKDEV_DEV_ID("fe1f0000.sound", &mstp_clks[MSTP328]),
- CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]),
- CLKDEV_DEV_ID("e6c20000.i2c", &mstp_clks[MSTP323]),
- CLKDEV_DEV_ID("renesas_usbhs", &mstp_clks[MSTP320]),
- CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP314]),
- CLKDEV_DEV_ID("e6850000.sd", &mstp_clks[MSTP314]),
- CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP313]),
- CLKDEV_DEV_ID("e6860000.sd", &mstp_clks[MSTP313]),
- CLKDEV_DEV_ID("sh_mmcif", &mstp_clks[MSTP312]),
- CLKDEV_DEV_ID("e6bd0000.mmc", &mstp_clks[MSTP312]),
- CLKDEV_DEV_ID("r8a7740-gether", &mstp_clks[MSTP309]),
- CLKDEV_DEV_ID("e9a00000.ethernet", &mstp_clks[MSTP309]),
- CLKDEV_DEV_ID("renesas-tpu-pwm", &mstp_clks[MSTP304]),
- CLKDEV_DEV_ID("e6600000.pwm", &mstp_clks[MSTP304]),
-
- CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP415]),
- CLKDEV_DEV_ID("e6870000.sd", &mstp_clks[MSTP415]),
-
- /* ICK */
- CLKDEV_ICK_ID("fck", "sh-tmu.1", &mstp_clks[MSTP111]),
- CLKDEV_ICK_ID("fck", "fff90000.timer", &mstp_clks[MSTP111]),
- CLKDEV_ICK_ID("fck", "sh-tmu.0", &mstp_clks[MSTP125]),
- CLKDEV_ICK_ID("fck", "fff80000.timer", &mstp_clks[MSTP125]),
- CLKDEV_ICK_ID("fck", "sh-cmt-48.1", &mstp_clks[MSTP329]),
- CLKDEV_ICK_ID("fck", "e6138000.timer", &mstp_clks[MSTP329]),
- CLKDEV_ICK_ID("host", "renesas_usbhs", &mstp_clks[MSTP416]),
- CLKDEV_ICK_ID("func", "renesas_usbhs", &mstp_clks[MSTP407]),
- CLKDEV_ICK_ID("phy", "renesas_usbhs", &mstp_clks[MSTP406]),
- CLKDEV_ICK_ID("pci", "renesas_usbhs", &div4_clks[DIV4_USBP]),
- CLKDEV_ICK_ID("usb24", "renesas_usbhs", &usb24_clk),
- CLKDEV_ICK_ID("ick", "sh-mobile-hdmi", &div6_reparent_clks[DIV6_HDMI]),
-
- CLKDEV_ICK_ID("icka", "sh_fsi2", &div6_reparent_clks[DIV6_FSIA]),
- CLKDEV_ICK_ID("ickb", "sh_fsi2", &div6_reparent_clks[DIV6_FSIB]),
- CLKDEV_ICK_ID("diva", "sh_fsi2", &fsidivs[FSIDIV_A]),
- CLKDEV_ICK_ID("divb", "sh_fsi2", &fsidivs[FSIDIV_B]),
- CLKDEV_ICK_ID("xcka", "sh_fsi2", &fsiack_clk),
- CLKDEV_ICK_ID("xckb", "sh_fsi2", &fsibck_clk),
-};
-
-void __init r8a7740_clock_init(u8 md_ck)
-{
- int k, ret = 0;
-
- /* detect system clock parent */
- if (md_ck & MD_CK1)
- system_clk.parent = &extal1_div2_clk;
- else
- system_clk.parent = &extal1_clk;
-
- /* detect RCLK parent */
- switch (md_ck & (MD_CK2 | MD_CK1)) {
- case MD_CK2 | MD_CK1:
- r_clk.parent = &extal1_div2048_clk;
- break;
- case MD_CK2:
- r_clk.parent = &extal1_div1024_clk;
- break;
- case MD_CK1:
- default:
- r_clk.parent = &extalr_clk;
- break;
- }
-
- for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
- ret = clk_register(main_clks[k]);
-
- if (!ret)
- ret = sh_clk_div4_register(div4_clks, DIV4_NR, &div4_table);
-
- if (!ret)
- ret = sh_clk_div6_register(div6_clks, DIV6_NR);
-
- if (!ret)
- ret = sh_clk_div6_reparent_register(div6_reparent_clks,
- DIV6_REPARENT_NR);
-
- if (!ret)
- ret = sh_clk_mstp_register(mstp_clks, MSTP_NR);
-
- for (k = 0; !ret && (k < ARRAY_SIZE(late_main_clks)); k++)
- ret = clk_register(late_main_clks[k]);
-
- if (!ret)
- ret = sh_clk_fsidiv_register(fsidivs, FSIDIV_REPARENT_NR);
-
- clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-
- if (!ret)
- shmobile_clk_init();
- else
- panic("failed to setup r8a7740 clocks\n");
-}
diff --git a/arch/arm/mach-shmobile/pm-r8a7740.c b/arch/arm/mach-shmobile/pm-r8a7740.c
deleted file mode 100644
index 34608fcf064808b8..0000000000000000
--- a/arch/arm/mach-shmobile/pm-r8a7740.c
+++ /dev/null
@@ -1,129 +0,0 @@
-/*
- * r8a7740 power management support
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#include <linux/console.h>
-#include <linux/io.h>
-#include <linux/suspend.h>
-
-#include "common.h"
-#include "pm-rmobile.h"
-
-#define SYSC_BASE IOMEM(0xe6180000)
-
-#if defined(CONFIG_PM) && !defined(CONFIG_ARCH_MULTIPLATFORM)
-static int r8a7740_pd_a3sm_suspend(void)
-{
- /*
- * The A3SM domain contains the CPU core and therefore it should
- * only be turned off if the CPU is not in use.
- */
- return -EBUSY;
-}
-
-static int r8a7740_pd_a3sp_suspend(void)
-{
- /*
- * Serial consoles make use of SCIF hardware located in A3SP,
- * keep such power domain on if "no_console_suspend" is set.
- */
- return console_suspend_enabled ? 0 : -EBUSY;
-}
-
-static int r8a7740_pd_d4_suspend(void)
-{
- /*
- * The D4 domain contains the Coresight-ETM hardware block and
- * therefore it should only be turned off if the debug module is
- * not in use.
- */
- return -EBUSY;
-}
-
-static struct rmobile_pm_domain r8a7740_pm_domains[] = {
- {
- .genpd.name = "A4LC",
- .base = SYSC_BASE,
- .bit_shift = 1,
- }, {
- .genpd.name = "A4MP",
- .base = SYSC_BASE,
- .bit_shift = 2,
- }, {
- .genpd.name = "D4",
- .base = SYSC_BASE,
- .bit_shift = 3,
- .gov = &pm_domain_always_on_gov,
- .suspend = r8a7740_pd_d4_suspend,
- }, {
- .genpd.name = "A4R",
- .base = SYSC_BASE,
- .bit_shift = 5,
- }, {
- .genpd.name = "A3RV",
- .base = SYSC_BASE,
- .bit_shift = 6,
- }, {
- .genpd.name = "A4S",
- .base = SYSC_BASE,
- .bit_shift = 10,
- .no_debug = true,
- }, {
- .genpd.name = "A3SP",
- .base = SYSC_BASE,
- .bit_shift = 11,
- .gov = &pm_domain_always_on_gov,
- .no_debug = true,
- .suspend = r8a7740_pd_a3sp_suspend,
- }, {
- .genpd.name = "A3SM",
- .base = SYSC_BASE,
- .bit_shift = 12,
- .gov = &pm_domain_always_on_gov,
- .suspend = r8a7740_pd_a3sm_suspend,
- }, {
- .genpd.name = "A3SG",
- .base = SYSC_BASE,
- .bit_shift = 13,
- }, {
- .genpd.name = "A4SU",
- .base = SYSC_BASE,
- .bit_shift = 20,
- },
-};
-
-void __init r8a7740_init_pm_domains(void)
-{
- rmobile_init_domains(r8a7740_pm_domains, ARRAY_SIZE(r8a7740_pm_domains));
- pm_genpd_add_subdomain_names("A4R", "A3RV");
- pm_genpd_add_subdomain_names("A4S", "A3SP");
- pm_genpd_add_subdomain_names("A4S", "A3SM");
- pm_genpd_add_subdomain_names("A4S", "A3SG");
-}
-#endif /* CONFIG_PM && !CONFIG_ARCH_MULTIPLATFORM */
-
-#ifdef CONFIG_SUSPEND
-static int r8a7740_enter_suspend(suspend_state_t suspend_state)
-{
- cpu_do_idle();
- return 0;
-}
-
-static void r8a7740_suspend_init(void)
-{
- shmobile_suspend_ops.enter = r8a7740_enter_suspend;
-}
-#else
-static void r8a7740_suspend_init(void) {}
-#endif
-
-void __init r8a7740_pm_init(void)
-{
- r8a7740_suspend_init();
-}
diff --git a/arch/arm/mach-shmobile/r8a7740.h b/arch/arm/mach-shmobile/r8a7740.h
deleted file mode 100644
index ca7805ad7ea3d64e..0000000000000000
--- a/arch/arm/mach-shmobile/r8a7740.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright (C) 2011 Renesas Solutions Corp.
- * Copyright (C) 2011 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_R8A7740_H__
-#define __ASM_R8A7740_H__
-
-/*
- * MD_CKx pin
- */
-#define MD_CK2 (1 << 2)
-#define MD_CK1 (1 << 1)
-#define MD_CK0 (1 << 0)
-
-/* DMA slave IDs */
-enum {
- SHDMA_SLAVE_INVALID,
- SHDMA_SLAVE_SDHI0_RX,
- SHDMA_SLAVE_SDHI0_TX,
- SHDMA_SLAVE_SDHI1_RX,
- SHDMA_SLAVE_SDHI1_TX,
- SHDMA_SLAVE_SDHI2_RX,
- SHDMA_SLAVE_SDHI2_TX,
- SHDMA_SLAVE_FSIA_RX,
- SHDMA_SLAVE_FSIA_TX,
- SHDMA_SLAVE_FSIB_TX,
- SHDMA_SLAVE_USBHS_TX,
- SHDMA_SLAVE_USBHS_RX,
- SHDMA_SLAVE_MMCIF_TX,
- SHDMA_SLAVE_MMCIF_RX,
-};
-
-extern void r8a7740_meram_workaround(void);
-extern void r8a7740_init_irq_of(void);
-extern void r8a7740_map_io(void);
-extern void r8a7740_add_early_devices(void);
-extern void r8a7740_add_standard_devices(void);
-extern void r8a7740_clock_init(u8 md_ck);
-extern void r8a7740_pinmux_init(void);
-extern void r8a7740_pm_init(void);
-
-#if defined(CONFIG_PM) && !defined(CONFIG_ARCH_MULTIPLATFORM)
-extern void __init r8a7740_init_pm_domains(void);
-#else
-static inline void r8a7740_init_pm_domains(void) {}
-#endif /* CONFIG_PM && !CONFIG_ARCH_MULTIPLATFORM */
-
-#endif /* __ASM_R8A7740_H__ */
diff --git a/arch/arm/mach-shmobile/setup-r8a7740.c b/arch/arm/mach-shmobile/setup-r8a7740.c
index 9832e48396a40a92..a6009ea79bd8b0aa 100644
--- a/arch/arm/mach-shmobile/setup-r8a7740.c
+++ b/arch/arm/mach-shmobile/setup-r8a7740.c
@@ -14,31 +14,19 @@
* GNU General Public License for more details.
*/
#include <linux/delay.h>
-#include <linux/dma-mapping.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-gic.h>
-#include <linux/platform_data/irq-renesas-intc-irqpin.h>
-#include <linux/platform_device.h>
#include <linux/of_platform.h>
-#include <linux/serial_sci.h>
-#include <linux/sh_dma.h>
-#include <linux/sh_timer.h>
-#include <linux/platform_data/sh_ipmmu.h>
-#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/hardware/cache-l2x0.h>
#include "common.h"
-#include "dma-register.h"
-#include "irqs.h"
-#include "pm-rmobile.h"
-#include "r8a7740.h"
static struct map_desc r8a7740_io_desc[] __initdata = {
/*
@@ -65,613 +53,12 @@ static struct map_desc r8a7740_io_desc[] __initdata = {
#endif
};
-void __init r8a7740_map_io(void)
+static void __init r8a7740_map_io(void)
{
debug_ll_io_init();
iotable_init(r8a7740_io_desc, ARRAY_SIZE(r8a7740_io_desc));
}
-/* PFC */
-static const struct resource pfc_resources[] = {
- DEFINE_RES_MEM(0xe6050000, 0x8000),
- DEFINE_RES_MEM(0xe605800c, 0x0020),
-};
-
-void __init r8a7740_pinmux_init(void)
-{
- platform_device_register_simple("pfc-r8a7740", -1, pfc_resources,
- ARRAY_SIZE(pfc_resources));
-}
-
-static struct renesas_intc_irqpin_config irqpin0_platform_data = {
- .irq_base = irq_pin(0), /* IRQ0 -> IRQ7 */
-};
-
-static struct resource irqpin0_resources[] = {
- DEFINE_RES_MEM(0xe6900000, 4), /* ICR1A */
- DEFINE_RES_MEM(0xe6900010, 4), /* INTPRI00A */
- DEFINE_RES_MEM(0xe6900020, 1), /* INTREQ00A */
- DEFINE_RES_MEM(0xe6900040, 1), /* INTMSK00A */
- DEFINE_RES_MEM(0xe6900060, 1), /* INTMSKCLR00A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ0 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ1 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ2 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ3 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ4 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ5 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ6 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ7 */
-};
-
-static struct platform_device irqpin0_device = {
- .name = "renesas_intc_irqpin",
- .id = 0,
- .resource = irqpin0_resources,
- .num_resources = ARRAY_SIZE(irqpin0_resources),
- .dev = {
- .platform_data = &irqpin0_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin1_platform_data = {
- .irq_base = irq_pin(8), /* IRQ8 -> IRQ15 */
-};
-
-static struct resource irqpin1_resources[] = {
- DEFINE_RES_MEM(0xe6900004, 4), /* ICR2A */
- DEFINE_RES_MEM(0xe6900014, 4), /* INTPRI10A */
- DEFINE_RES_MEM(0xe6900024, 1), /* INTREQ10A */
- DEFINE_RES_MEM(0xe6900044, 1), /* INTMSK10A */
- DEFINE_RES_MEM(0xe6900064, 1), /* INTMSKCLR10A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ8 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ9 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ10 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ11 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ12 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ13 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ14 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ15 */
-};
-
-static struct platform_device irqpin1_device = {
- .name = "renesas_intc_irqpin",
- .id = 1,
- .resource = irqpin1_resources,
- .num_resources = ARRAY_SIZE(irqpin1_resources),
- .dev = {
- .platform_data = &irqpin1_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin2_platform_data = {
- .irq_base = irq_pin(16), /* IRQ16 -> IRQ23 */
-};
-
-static struct resource irqpin2_resources[] = {
- DEFINE_RES_MEM(0xe6900008, 4), /* ICR3A */
- DEFINE_RES_MEM(0xe6900018, 4), /* INTPRI30A */
- DEFINE_RES_MEM(0xe6900028, 1), /* INTREQ30A */
- DEFINE_RES_MEM(0xe6900048, 1), /* INTMSK30A */
- DEFINE_RES_MEM(0xe6900068, 1), /* INTMSKCLR30A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ16 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ17 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ18 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ19 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ20 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ21 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ22 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ23 */
-};
-
-static struct platform_device irqpin2_device = {
- .name = "renesas_intc_irqpin",
- .id = 2,
- .resource = irqpin2_resources,
- .num_resources = ARRAY_SIZE(irqpin2_resources),
- .dev = {
- .platform_data = &irqpin2_platform_data,
- },
-};
-
-static struct renesas_intc_irqpin_config irqpin3_platform_data = {
- .irq_base = irq_pin(24), /* IRQ24 -> IRQ31 */
-};
-
-static struct resource irqpin3_resources[] = {
- DEFINE_RES_MEM(0xe690000c, 4), /* ICR3A */
- DEFINE_RES_MEM(0xe690001c, 4), /* INTPRI30A */
- DEFINE_RES_MEM(0xe690002c, 1), /* INTREQ30A */
- DEFINE_RES_MEM(0xe690004c, 1), /* INTMSK30A */
- DEFINE_RES_MEM(0xe690006c, 1), /* INTMSKCLR30A */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ24 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ25 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ26 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ27 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ28 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ29 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ30 */
- DEFINE_RES_IRQ(gic_spi(149)), /* IRQ31 */
-};
-
-static struct platform_device irqpin3_device = {
- .name = "renesas_intc_irqpin",
- .id = 3,
- .resource = irqpin3_resources,
- .num_resources = ARRAY_SIZE(irqpin3_resources),
- .dev = {
- .platform_data = &irqpin3_platform_data,
- },
-};
-
-/* SCIF */
-#define R8A7740_SCIF(scif_type, index, baseaddr, irq) \
-static struct plat_sci_port scif##index##_platform_data = { \
- .type = scif_type, \
- .flags = UPF_BOOT_AUTOCONF, \
- .scscr = SCSCR_RE | SCSCR_TE, \
-}; \
- \
-static struct resource scif##index##_resources[] = { \
- DEFINE_RES_MEM(baseaddr, 0x100), \
- DEFINE_RES_IRQ(irq), \
-}; \
- \
-static struct platform_device scif##index##_device = { \
- .name = "sh-sci", \
- .id = index, \
- .resource = scif##index##_resources, \
- .num_resources = ARRAY_SIZE(scif##index##_resources), \
- .dev = { \
- .platform_data = &scif##index##_platform_data, \
- }, \
-}
-
-R8A7740_SCIF(PORT_SCIFA, 0, 0xe6c40000, gic_spi(100));
-R8A7740_SCIF(PORT_SCIFA, 1, 0xe6c50000, gic_spi(101));
-R8A7740_SCIF(PORT_SCIFA, 2, 0xe6c60000, gic_spi(102));
-R8A7740_SCIF(PORT_SCIFA, 3, 0xe6c70000, gic_spi(103));
-R8A7740_SCIF(PORT_SCIFA, 4, 0xe6c80000, gic_spi(104));
-R8A7740_SCIF(PORT_SCIFA, 5, 0xe6cb0000, gic_spi(105));
-R8A7740_SCIF(PORT_SCIFA, 6, 0xe6cc0000, gic_spi(106));
-R8A7740_SCIF(PORT_SCIFA, 7, 0xe6cd0000, gic_spi(107));
-R8A7740_SCIF(PORT_SCIFB, 8, 0xe6c30000, gic_spi(108));
-
-/* CMT */
-static struct sh_timer_config cmt1_platform_data = {
- .channels_mask = 0x3f,
-};
-
-static struct resource cmt1_resources[] = {
- DEFINE_RES_MEM(0xe6138000, 0x170),
- DEFINE_RES_IRQ(gic_spi(58)),
-};
-
-static struct platform_device cmt1_device = {
- .name = "sh-cmt-48",
- .id = 1,
- .dev = {
- .platform_data = &cmt1_platform_data,
- },
- .resource = cmt1_resources,
- .num_resources = ARRAY_SIZE(cmt1_resources),
-};
-
-/* TMU */
-static struct sh_timer_config tmu0_platform_data = {
- .channels_mask = 7,
-};
-
-static struct resource tmu0_resources[] = {
- DEFINE_RES_MEM(0xfff80000, 0x2c),
- DEFINE_RES_IRQ(gic_spi(198)),
- DEFINE_RES_IRQ(gic_spi(199)),
- DEFINE_RES_IRQ(gic_spi(200)),
-};
-
-static struct platform_device tmu0_device = {
- .name = "sh-tmu",
- .id = 0,
- .dev = {
- .platform_data = &tmu0_platform_data,
- },
- .resource = tmu0_resources,
- .num_resources = ARRAY_SIZE(tmu0_resources),
-};
-
-/* IPMMUI (an IPMMU module for ICB/LMB) */
-static struct resource ipmmu_resources[] = {
- [0] = {
- .name = "IPMMUI",
- .start = 0xfe951000,
- .end = 0xfe9510ff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static const char * const ipmmu_dev_names[] = {
- "sh_mobile_lcdc_fb.0",
- "sh_mobile_lcdc_fb.1",
- "sh_mobile_ceu.0",
-};
-
-static struct shmobile_ipmmu_platform_data ipmmu_platform_data = {
- .dev_names = ipmmu_dev_names,
- .num_dev_names = ARRAY_SIZE(ipmmu_dev_names),
-};
-
-static struct platform_device ipmmu_device = {
- .name = "ipmmu",
- .id = -1,
- .dev = {
- .platform_data = &ipmmu_platform_data,
- },
- .resource = ipmmu_resources,
- .num_resources = ARRAY_SIZE(ipmmu_resources),
-};
-
-static struct platform_device *r8a7740_early_devices[] __initdata = {
- &scif0_device,
- &scif1_device,
- &scif2_device,
- &scif3_device,
- &scif4_device,
- &scif5_device,
- &scif6_device,
- &scif7_device,
- &scif8_device,
- &irqpin0_device,
- &irqpin1_device,
- &irqpin2_device,
- &irqpin3_device,
- &tmu0_device,
- &ipmmu_device,
- &cmt1_device,
-};
-
-/* DMA */
-static const struct sh_dmae_slave_config r8a7740_dmae_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_SDHI0_TX,
- .addr = 0xe6850030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc1,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI0_RX,
- .addr = 0xe6850030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xc2,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_TX,
- .addr = 0xe6860030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xc9,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI1_RX,
- .addr = 0xe6860030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xca,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_TX,
- .addr = 0xe6870030,
- .chcr = CHCR_TX(XMIT_SZ_16BIT),
- .mid_rid = 0xcd,
- }, {
- .slave_id = SHDMA_SLAVE_SDHI2_RX,
- .addr = 0xe6870030,
- .chcr = CHCR_RX(XMIT_SZ_16BIT),
- .mid_rid = 0xce,
- }, {
- .slave_id = SHDMA_SLAVE_FSIA_TX,
- .addr = 0xfe1f0024,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xb1,
- }, {
- .slave_id = SHDMA_SLAVE_FSIA_RX,
- .addr = 0xfe1f0020,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xb2,
- }, {
- .slave_id = SHDMA_SLAVE_FSIB_TX,
- .addr = 0xfe1f0064,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xb5,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_TX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_TX(XMIT_SZ_32BIT),
- .mid_rid = 0xd1,
- }, {
- .slave_id = SHDMA_SLAVE_MMCIF_RX,
- .addr = 0xe6bd0034,
- .chcr = CHCR_RX(XMIT_SZ_32BIT),
- .mid_rid = 0xd2,
- },
-};
-
-#define DMA_CHANNEL(a, b, c) \
-{ \
- .offset = a, \
- .dmars = b, \
- .dmars_bit = c, \
- .chclr_offset = (0x220 - 0x20) + a \
-}
-
-static const struct sh_dmae_channel r8a7740_dmae_channels[] = {
- DMA_CHANNEL(0x00, 0, 0),
- DMA_CHANNEL(0x10, 0, 8),
- DMA_CHANNEL(0x20, 4, 0),
- DMA_CHANNEL(0x30, 4, 8),
- DMA_CHANNEL(0x50, 8, 0),
- DMA_CHANNEL(0x60, 8, 8),
-};
-
-static struct sh_dmae_pdata dma_platform_data = {
- .slave = r8a7740_dmae_slaves,
- .slave_num = ARRAY_SIZE(r8a7740_dmae_slaves),
- .channel = r8a7740_dmae_channels,
- .channel_num = ARRAY_SIZE(r8a7740_dmae_channels),
- .ts_low_shift = TS_LOW_SHIFT,
- .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
- .ts_high_shift = TS_HI_SHIFT,
- .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
- .ts_shift = dma_ts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
- .dmaor_init = DMAOR_DME,
- .chclr_present = 1,
-};
-
-/* Resource order important! */
-static struct resource r8a7740_dmae0_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xfe008020,
- .end = 0xfe00828f,
- .flags = IORESOURCE_MEM,
- },
- {
- /* DMARSx */
- .start = 0xfe009000,
- .end = 0xfe00900b,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "error_irq",
- .start = gic_spi(34),
- .end = gic_spi(34),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(28),
- .end = gic_spi(33),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-/* Resource order important! */
-static struct resource r8a7740_dmae1_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xfe018020,
- .end = 0xfe01828f,
- .flags = IORESOURCE_MEM,
- },
- {
- /* DMARSx */
- .start = 0xfe019000,
- .end = 0xfe01900b,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "error_irq",
- .start = gic_spi(41),
- .end = gic_spi(41),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(35),
- .end = gic_spi(40),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-/* Resource order important! */
-static struct resource r8a7740_dmae2_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xfe028020,
- .end = 0xfe02828f,
- .flags = IORESOURCE_MEM,
- },
- {
- /* DMARSx */
- .start = 0xfe029000,
- .end = 0xfe02900b,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "error_irq",
- .start = gic_spi(48),
- .end = gic_spi(48),
- .flags = IORESOURCE_IRQ,
- },
- {
- /* IRQ for channels 0-5 */
- .start = gic_spi(42),
- .end = gic_spi(47),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device dma0_device = {
- .name = "sh-dma-engine",
- .id = 0,
- .resource = r8a7740_dmae0_resources,
- .num_resources = ARRAY_SIZE(r8a7740_dmae0_resources),
- .dev = {
- .platform_data = &dma_platform_data,
- },
-};
-
-static struct platform_device dma1_device = {
- .name = "sh-dma-engine",
- .id = 1,
- .resource = r8a7740_dmae1_resources,
- .num_resources = ARRAY_SIZE(r8a7740_dmae1_resources),
- .dev = {
- .platform_data = &dma_platform_data,
- },
-};
-
-static struct platform_device dma2_device = {
- .name = "sh-dma-engine",
- .id = 2,
- .resource = r8a7740_dmae2_resources,
- .num_resources = ARRAY_SIZE(r8a7740_dmae2_resources),
- .dev = {
- .platform_data = &dma_platform_data,
- },
-};
-
-/* USB-DMAC */
-static const struct sh_dmae_channel r8a7740_usb_dma_channels[] = {
- {
- .offset = 0,
- }, {
- .offset = 0x20,
- },
-};
-
-static const struct sh_dmae_slave_config r8a7740_usb_dma_slaves[] = {
- {
- .slave_id = SHDMA_SLAVE_USBHS_TX,
- .chcr = USBTS_INDEX2VAL(USBTS_XMIT_SZ_8BYTE),
- }, {
- .slave_id = SHDMA_SLAVE_USBHS_RX,
- .chcr = USBTS_INDEX2VAL(USBTS_XMIT_SZ_8BYTE),
- },
-};
-
-static struct sh_dmae_pdata usb_dma_platform_data = {
- .slave = r8a7740_usb_dma_slaves,
- .slave_num = ARRAY_SIZE(r8a7740_usb_dma_slaves),
- .channel = r8a7740_usb_dma_channels,
- .channel_num = ARRAY_SIZE(r8a7740_usb_dma_channels),
- .ts_low_shift = USBTS_LOW_SHIFT,
- .ts_low_mask = USBTS_LOW_BIT << USBTS_LOW_SHIFT,
- .ts_high_shift = USBTS_HI_SHIFT,
- .ts_high_mask = USBTS_HI_BIT << USBTS_HI_SHIFT,
- .ts_shift = dma_usbts_shift,
- .ts_shift_num = ARRAY_SIZE(dma_usbts_shift),
- .dmaor_init = DMAOR_DME,
- .chcr_offset = 0x14,
- .chcr_ie_bit = 1 << 5,
- .dmaor_is_32bit = 1,
- .needs_tend_set = 1,
- .no_dmars = 1,
- .slave_only = 1,
-};
-
-static struct resource r8a7740_usb_dma_resources[] = {
- {
- /* Channel registers and DMAOR */
- .start = 0xe68a0020,
- .end = 0xe68a0064 - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- /* VCR/SWR/DMICR */
- .start = 0xe68a0000,
- .end = 0xe68a0014 - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- /* IRQ for channels */
- .start = gic_spi(49),
- .end = gic_spi(49),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device usb_dma_device = {
- .name = "sh-dma-engine",
- .id = 3,
- .resource = r8a7740_usb_dma_resources,
- .num_resources = ARRAY_SIZE(r8a7740_usb_dma_resources),
- .dev = {
- .platform_data = &usb_dma_platform_data,
- },
-};
-
-/* I2C */
-static struct resource i2c0_resources[] = {
- [0] = {
- .name = "IIC0",
- .start = 0xfff20000,
- .end = 0xfff20425 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(201),
- .end = gic_spi(204),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- [0] = {
- .name = "IIC1",
- .start = 0xe6c20000,
- .end = 0xe6c20425 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = gic_spi(70), /* IIC1_ALI1 */
- .end = gic_spi(73), /* IIC1_DTEI1 */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device i2c0_device = {
- .name = "i2c-sh_mobile",
- .id = 0,
- .resource = i2c0_resources,
- .num_resources = ARRAY_SIZE(i2c0_resources),
-};
-
-static struct platform_device i2c1_device = {
- .name = "i2c-sh_mobile",
- .id = 1,
- .resource = i2c1_resources,
- .num_resources = ARRAY_SIZE(i2c1_resources),
-};
-
-static struct resource pmu_resources[] = {
- [0] = {
- .start = gic_spi(83),
- .end = gic_spi(83),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device pmu_device = {
- .name = "armv7-pmu",
- .id = -1,
- .num_resources = ARRAY_SIZE(pmu_resources),
- .resource = pmu_resources,
-};
-
-static struct platform_device *r8a7740_late_devices[] __initdata = {
- &i2c0_device,
- &i2c1_device,
- &dma0_device,
- &dma1_device,
- &dma2_device,
- &usb_dma_device,
- &pmu_device,
-};
-
/*
* r8a7740 chip has lasting errata on MERAM buffer.
* this is work-around for it.
@@ -679,7 +66,7 @@ static struct platform_device *r8a7740_late_devices[] __initdata = {
* "Media RAM (MERAM)" on r8a7740 documentation
*/
#define MEBUFCNTR 0xFE950098
-void __init r8a7740_meram_workaround(void)
+static void __init r8a7740_meram_workaround(void)
{
void __iomem *reg;
@@ -690,124 +77,13 @@ void __init r8a7740_meram_workaround(void)
}
}
-#define ICCR 0x0004
-#define ICSTART 0x0070
-
-#define i2c_read(reg, offset) ioread8(reg + offset)
-#define i2c_write(reg, offset, data) iowrite8(data, reg + offset)
-
-/*
- * r8a7740 chip has lasting errata on I2C I/O pad reset.
- * this is work-around for it.
- */
-static void r8a7740_i2c_workaround(struct platform_device *pdev)
-{
- struct resource *res;
- void __iomem *reg;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (unlikely(!res)) {
- pr_err("r8a7740 i2c workaround fail (cannot find resource)\n");
- return;
- }
-
- reg = ioremap(res->start, resource_size(res));
- if (unlikely(!reg)) {
- pr_err("r8a7740 i2c workaround fail (cannot map IO)\n");
- return;
- }
-
- i2c_write(reg, ICCR, i2c_read(reg, ICCR) | 0x80);
- i2c_read(reg, ICCR); /* dummy read */
-
- i2c_write(reg, ICSTART, i2c_read(reg, ICSTART) | 0x10);
- i2c_read(reg, ICSTART); /* dummy read */
-
- udelay(10);
-
- i2c_write(reg, ICCR, 0x01);
- i2c_write(reg, ICSTART, 0x00);
-
- udelay(10);
-
- i2c_write(reg, ICCR, 0x10);
- udelay(10);
- i2c_write(reg, ICCR, 0x00);
- udelay(10);
- i2c_write(reg, ICCR, 0x10);
- udelay(10);
-
- iounmap(reg);
-}
-
-void __init r8a7740_add_standard_devices(void)
-{
- static struct pm_domain_device domain_devices[] __initdata = {
- { "A4R", &tmu0_device },
- { "A4R", &i2c0_device },
- { "A4S", &irqpin0_device },
- { "A4S", &irqpin1_device },
- { "A4S", &irqpin2_device },
- { "A4S", &irqpin3_device },
- { "A3SP", &scif0_device },
- { "A3SP", &scif1_device },
- { "A3SP", &scif2_device },
- { "A3SP", &scif3_device },
- { "A3SP", &scif4_device },
- { "A3SP", &scif5_device },
- { "A3SP", &scif6_device },
- { "A3SP", &scif7_device },
- { "A3SP", &scif8_device },
- { "A3SP", &i2c1_device },
- { "A3SP", &ipmmu_device },
- { "A3SP", &dma0_device },
- { "A3SP", &dma1_device },
- { "A3SP", &dma2_device },
- { "A3SP", &usb_dma_device },
- };
-
- /* I2C work-around */
- r8a7740_i2c_workaround(&i2c0_device);
- r8a7740_i2c_workaround(&i2c1_device);
-
- r8a7740_init_pm_domains();
-
- /* add devices */
- platform_add_devices(r8a7740_early_devices,
- ARRAY_SIZE(r8a7740_early_devices));
- platform_add_devices(r8a7740_late_devices,
- ARRAY_SIZE(r8a7740_late_devices));
-
- /* add devices to PM domain */
- rmobile_add_devices_to_domains(domain_devices,
- ARRAY_SIZE(domain_devices));
-}
-
-void __init r8a7740_add_early_devices(void)
-{
- early_platform_add_devices(r8a7740_early_devices,
- ARRAY_SIZE(r8a7740_early_devices));
-
- /* setup early console here as well */
- shmobile_setup_console();
-}
-
-#ifdef CONFIG_USE_OF
-
-void __init r8a7740_init_irq_of(void)
+static void __init r8a7740_init_irq_of(void)
{
void __iomem *intc_prio_base = ioremap_nocache(0xe6900010, 0x10);
void __iomem *intc_msk_base = ioremap_nocache(0xe6900040, 0x10);
void __iomem *pfc_inta_ctrl = ioremap_nocache(0xe605807c, 0x4);
-#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
- void __iomem *gic_dist_base = ioremap_nocache(0xc2800000, 0x1000);
- void __iomem *gic_cpu_base = ioremap_nocache(0xc2000000, 0x1000);
-
- gic_init(0, 29, gic_dist_base, gic_cpu_base);
-#else
irqchip_init();
-#endif
/* route signals to GIC */
iowrite32(0x0, pfc_inta_ctrl);
@@ -855,5 +131,3 @@ DT_MACHINE_START(R8A7740_DT, "Generic R8A7740 (Flattened Device Tree)")
.init_late = shmobile_init_late,
.dt_compat = r8a7740_boards_compat_dt,
MACHINE_END
-
-#endif /* CONFIG_USE_OF */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 09/15] ARM: shmobile: Remove unused dma-register.h
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last users of "dma-register.h" were the sh73a0 and r8a7740 legacy
SoC code, which have been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/dma-register.h | 84 -----------------------------------
1 file changed, 84 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/dma-register.h
diff --git a/arch/arm/mach-shmobile/dma-register.h b/arch/arm/mach-shmobile/dma-register.h
deleted file mode 100644
index 52a2f66e600f2995..0000000000000000
--- a/arch/arm/mach-shmobile/dma-register.h
+++ /dev/null
@@ -1,84 +0,0 @@
-/*
- * SH-ARM CPU-specific DMA definitions, used by both DMA drivers
- *
- * Copyright (C) 2012 Renesas Solutions Corp
- *
- * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * Based on arch/sh/include/cpu-sh4/cpu/dma-register.h
- * Copyright (C) 2010 Guennadi Liakhovetski <g.liakhovetski@gmx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef DMA_REGISTER_H
-#define DMA_REGISTER_H
-
-/*
- * Direct Memory Access Controller
- */
-
-/* Transmit sizes and respective CHCR register values */
-enum {
- XMIT_SZ_8BIT = 0,
- XMIT_SZ_16BIT = 1,
- XMIT_SZ_32BIT = 2,
- XMIT_SZ_64BIT = 7,
- XMIT_SZ_128BIT = 3,
- XMIT_SZ_256BIT = 4,
- XMIT_SZ_512BIT = 5,
-};
-
-/* log2(size / 8) - used to calculate number of transfers */
-static const unsigned int dma_ts_shift[] = {
- [XMIT_SZ_8BIT] = 0,
- [XMIT_SZ_16BIT] = 1,
- [XMIT_SZ_32BIT] = 2,
- [XMIT_SZ_64BIT] = 3,
- [XMIT_SZ_128BIT] = 4,
- [XMIT_SZ_256BIT] = 5,
- [XMIT_SZ_512BIT] = 6,
-};
-
-#define TS_LOW_BIT 0x3 /* --xx */
-#define TS_HI_BIT 0xc /* xx-- */
-
-#define TS_LOW_SHIFT (3)
-#define TS_HI_SHIFT (20 - 2) /* 2 bits for shifted low TS */
-
-#define TS_INDEX2VAL(i) \
- ((((i) & TS_LOW_BIT) << TS_LOW_SHIFT) |\
- (((i) & TS_HI_BIT) << TS_HI_SHIFT))
-
-#define CHCR_TX(xmit_sz) (DM_FIX | SM_INC | RS_ERS | TS_INDEX2VAL((xmit_sz)))
-#define CHCR_RX(xmit_sz) (DM_INC | SM_FIX | RS_ERS | TS_INDEX2VAL((xmit_sz)))
-
-
-/*
- * USB High-Speed DMAC
- */
-/* Transmit sizes and respective CHCR register values */
-enum {
- USBTS_XMIT_SZ_8BYTE = 0,
- USBTS_XMIT_SZ_16BYTE = 1,
- USBTS_XMIT_SZ_32BYTE = 2,
-};
-
-/* log2(size / 8) - used to calculate number of transfers */
-static const unsigned int dma_usbts_shift[] = {
- [USBTS_XMIT_SZ_8BYTE] = 3,
- [USBTS_XMIT_SZ_16BYTE] = 4,
- [USBTS_XMIT_SZ_32BYTE] = 5,
-};
-
-#define USBTS_LOW_BIT 0x3 /* --xx */
-#define USBTS_HI_BIT 0x0 /* ---- */
-
-#define USBTS_LOW_SHIFT 6
-#define USBTS_HI_SHIFT 0
-
-#define USBTS_INDEX2VAL(i) (((i) & 3) << 6)
-
-#endif /* DMA_REGISTER_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 09/15] ARM: shmobile: Remove unused dma-register.h
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last users of "dma-register.h" were the sh73a0 and r8a7740 legacy
SoC code, which have been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/dma-register.h | 84 -----------------------------------
1 file changed, 84 deletions(-)
delete mode 100644 arch/arm/mach-shmobile/dma-register.h
diff --git a/arch/arm/mach-shmobile/dma-register.h b/arch/arm/mach-shmobile/dma-register.h
deleted file mode 100644
index 52a2f66e600f2995..0000000000000000
--- a/arch/arm/mach-shmobile/dma-register.h
+++ /dev/null
@@ -1,84 +0,0 @@
-/*
- * SH-ARM CPU-specific DMA definitions, used by both DMA drivers
- *
- * Copyright (C) 2012 Renesas Solutions Corp
- *
- * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * Based on arch/sh/include/cpu-sh4/cpu/dma-register.h
- * Copyright (C) 2010 Guennadi Liakhovetski <g.liakhovetski@gmx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef DMA_REGISTER_H
-#define DMA_REGISTER_H
-
-/*
- * Direct Memory Access Controller
- */
-
-/* Transmit sizes and respective CHCR register values */
-enum {
- XMIT_SZ_8BIT = 0,
- XMIT_SZ_16BIT = 1,
- XMIT_SZ_32BIT = 2,
- XMIT_SZ_64BIT = 7,
- XMIT_SZ_128BIT = 3,
- XMIT_SZ_256BIT = 4,
- XMIT_SZ_512BIT = 5,
-};
-
-/* log2(size / 8) - used to calculate number of transfers */
-static const unsigned int dma_ts_shift[] = {
- [XMIT_SZ_8BIT] = 0,
- [XMIT_SZ_16BIT] = 1,
- [XMIT_SZ_32BIT] = 2,
- [XMIT_SZ_64BIT] = 3,
- [XMIT_SZ_128BIT] = 4,
- [XMIT_SZ_256BIT] = 5,
- [XMIT_SZ_512BIT] = 6,
-};
-
-#define TS_LOW_BIT 0x3 /* --xx */
-#define TS_HI_BIT 0xc /* xx-- */
-
-#define TS_LOW_SHIFT (3)
-#define TS_HI_SHIFT (20 - 2) /* 2 bits for shifted low TS */
-
-#define TS_INDEX2VAL(i) \
- ((((i) & TS_LOW_BIT) << TS_LOW_SHIFT) |\
- (((i) & TS_HI_BIT) << TS_HI_SHIFT))
-
-#define CHCR_TX(xmit_sz) (DM_FIX | SM_INC | RS_ERS | TS_INDEX2VAL((xmit_sz)))
-#define CHCR_RX(xmit_sz) (DM_INC | SM_FIX | RS_ERS | TS_INDEX2VAL((xmit_sz)))
-
-
-/*
- * USB High-Speed DMAC
- */
-/* Transmit sizes and respective CHCR register values */
-enum {
- USBTS_XMIT_SZ_8BYTE = 0,
- USBTS_XMIT_SZ_16BYTE = 1,
- USBTS_XMIT_SZ_32BYTE = 2,
-};
-
-/* log2(size / 8) - used to calculate number of transfers */
-static const unsigned int dma_usbts_shift[] = {
- [USBTS_XMIT_SZ_8BYTE] = 3,
- [USBTS_XMIT_SZ_16BYTE] = 4,
- [USBTS_XMIT_SZ_32BYTE] = 5,
-};
-
-#define USBTS_LOW_BIT 0x3 /* --xx */
-#define USBTS_HI_BIT 0x0 /* ---- */
-
-#define USBTS_LOW_SHIFT 6
-#define USBTS_HI_SHIFT 0
-
-#define USBTS_INDEX2VAL(i) (((i) & 3) << 6)
-
-#endif /* DMA_REGISTER_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 10/15] ARM: shmobile: R-Mobile: Remove legacy PM Domain code
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the legacy R-Mobile PM Domain code was the r8a7740
legacy SoC code, which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/pm-rmobile.c | 39 -------------------------------------
arch/arm/mach-shmobile/pm-rmobile.h | 24 -----------------------
2 files changed, 63 deletions(-)
diff --git a/arch/arm/mach-shmobile/pm-rmobile.c b/arch/arm/mach-shmobile/pm-rmobile.c
index b9b494f5ca99fc7c..a5b96b990aea8dfc 100644
--- a/arch/arm/mach-shmobile/pm-rmobile.c
+++ b/arch/arm/mach-shmobile/pm-rmobile.c
@@ -169,43 +169,6 @@ static void rmobile_init_pm_domain(struct rmobile_pm_domain *rmobile_pd)
__rmobile_pd_power_up(rmobile_pd, false);
}
-#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
-
-void rmobile_init_domains(struct rmobile_pm_domain domains[], int num)
-{
- int j;
-
- for (j = 0; j < num; j++)
- rmobile_init_pm_domain(&domains[j]);
-}
-
-void rmobile_add_device_to_domain_td(const char *domain_name,
- struct platform_device *pdev,
- struct gpd_timing_data *td)
-{
- struct device *dev = &pdev->dev;
-
- __pm_genpd_name_add_device(domain_name, dev, td);
-}
-
-void rmobile_add_devices_to_domains(struct pm_domain_device data[],
- int size)
-{
- struct gpd_timing_data latencies = {
- .stop_latency_ns = DEFAULT_DEV_LATENCY_NS,
- .start_latency_ns = DEFAULT_DEV_LATENCY_NS,
- .save_state_latency_ns = DEFAULT_DEV_LATENCY_NS,
- .restore_state_latency_ns = DEFAULT_DEV_LATENCY_NS,
- };
- int j;
-
- for (j = 0; j < size; j++)
- rmobile_add_device_to_domain_td(data[j].domain_name,
- data[j].pdev, &latencies);
-}
-
-#else /* !CONFIG_ARCH_SHMOBILE_LEGACY */
-
static int rmobile_pd_suspend_busy(void)
{
/*
@@ -436,5 +399,3 @@ static int __init rmobile_init_pm_domains(void)
}
core_initcall(rmobile_init_pm_domains);
-
-#endif /* !CONFIG_ARCH_SHMOBILE_LEGACY */
diff --git a/arch/arm/mach-shmobile/pm-rmobile.h b/arch/arm/mach-shmobile/pm-rmobile.h
index 3992b619c1278dcc..30a4a421ee315b98 100644
--- a/arch/arm/mach-shmobile/pm-rmobile.h
+++ b/arch/arm/mach-shmobile/pm-rmobile.h
@@ -31,28 +31,4 @@ struct pm_domain_device {
struct platform_device *pdev;
};
-#if defined(CONFIG_PM_RMOBILE) && defined(CONFIG_ARCH_SHMOBILE_LEGACY)
-extern void rmobile_init_domains(struct rmobile_pm_domain domains[], int num);
-extern void rmobile_add_device_to_domain_td(const char *domain_name,
- struct platform_device *pdev,
- struct gpd_timing_data *td);
-
-static inline void rmobile_add_device_to_domain(const char *domain_name,
- struct platform_device *pdev)
-{
- rmobile_add_device_to_domain_td(domain_name, pdev, NULL);
-}
-
-extern void rmobile_add_devices_to_domains(struct pm_domain_device data[],
- int size);
-#else
-
-#define rmobile_init_domains(domains, num) do { } while (0)
-#define rmobile_add_device_to_domain_td(name, pdev, td) do { } while (0)
-#define rmobile_add_device_to_domain(name, pdev) do { } while (0)
-
-static inline void rmobile_add_devices_to_domains(struct pm_domain_device d[],
- int size) {}
-#endif /* CONFIG_PM_RMOBILE */
-
#endif /* PM_RMOBILE_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 10/15] ARM: shmobile: R-Mobile: Remove legacy PM Domain code
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the legacy R-Mobile PM Domain code was the r8a7740
legacy SoC code, which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/mach-shmobile/pm-rmobile.c | 39 -------------------------------------
arch/arm/mach-shmobile/pm-rmobile.h | 24 -----------------------
2 files changed, 63 deletions(-)
diff --git a/arch/arm/mach-shmobile/pm-rmobile.c b/arch/arm/mach-shmobile/pm-rmobile.c
index b9b494f5ca99fc7c..a5b96b990aea8dfc 100644
--- a/arch/arm/mach-shmobile/pm-rmobile.c
+++ b/arch/arm/mach-shmobile/pm-rmobile.c
@@ -169,43 +169,6 @@ static void rmobile_init_pm_domain(struct rmobile_pm_domain *rmobile_pd)
__rmobile_pd_power_up(rmobile_pd, false);
}
-#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
-
-void rmobile_init_domains(struct rmobile_pm_domain domains[], int num)
-{
- int j;
-
- for (j = 0; j < num; j++)
- rmobile_init_pm_domain(&domains[j]);
-}
-
-void rmobile_add_device_to_domain_td(const char *domain_name,
- struct platform_device *pdev,
- struct gpd_timing_data *td)
-{
- struct device *dev = &pdev->dev;
-
- __pm_genpd_name_add_device(domain_name, dev, td);
-}
-
-void rmobile_add_devices_to_domains(struct pm_domain_device data[],
- int size)
-{
- struct gpd_timing_data latencies = {
- .stop_latency_ns = DEFAULT_DEV_LATENCY_NS,
- .start_latency_ns = DEFAULT_DEV_LATENCY_NS,
- .save_state_latency_ns = DEFAULT_DEV_LATENCY_NS,
- .restore_state_latency_ns = DEFAULT_DEV_LATENCY_NS,
- };
- int j;
-
- for (j = 0; j < size; j++)
- rmobile_add_device_to_domain_td(data[j].domain_name,
- data[j].pdev, &latencies);
-}
-
-#else /* !CONFIG_ARCH_SHMOBILE_LEGACY */
-
static int rmobile_pd_suspend_busy(void)
{
/*
@@ -436,5 +399,3 @@ static int __init rmobile_init_pm_domains(void)
}
core_initcall(rmobile_init_pm_domains);
-
-#endif /* !CONFIG_ARCH_SHMOBILE_LEGACY */
diff --git a/arch/arm/mach-shmobile/pm-rmobile.h b/arch/arm/mach-shmobile/pm-rmobile.h
index 3992b619c1278dcc..30a4a421ee315b98 100644
--- a/arch/arm/mach-shmobile/pm-rmobile.h
+++ b/arch/arm/mach-shmobile/pm-rmobile.h
@@ -31,28 +31,4 @@ struct pm_domain_device {
struct platform_device *pdev;
};
-#if defined(CONFIG_PM_RMOBILE) && defined(CONFIG_ARCH_SHMOBILE_LEGACY)
-extern void rmobile_init_domains(struct rmobile_pm_domain domains[], int num);
-extern void rmobile_add_device_to_domain_td(const char *domain_name,
- struct platform_device *pdev,
- struct gpd_timing_data *td);
-
-static inline void rmobile_add_device_to_domain(const char *domain_name,
- struct platform_device *pdev)
-{
- rmobile_add_device_to_domain_td(domain_name, pdev, NULL);
-}
-
-extern void rmobile_add_devices_to_domains(struct pm_domain_device data[],
- int size);
-#else
-
-#define rmobile_init_domains(domains, num) do { } while (0)
-#define rmobile_add_device_to_domain_td(name, pdev, td) do { } while (0)
-#define rmobile_add_device_to_domain(name, pdev) do { } while (0)
-
-static inline void rmobile_add_devices_to_domains(struct pm_domain_device d[],
- int size) {}
-#endif /* CONFIG_PM_RMOBILE */
-
#endif /* PM_RMOBILE_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 11/15] ARM: shmobile: Remove obsolete zboot support
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the zboot code was the KZM-A9-GT legacy board code,
which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/boot/compressed/Makefile | 4 -
arch/arm/boot/compressed/head-shmobile.S | 71 --------------
arch/arm/mach-shmobile/include/mach/zboot.h | 14 ---
arch/arm/mach-shmobile/include/mach/zboot_macros.h | 108 ---------------------
4 files changed, 197 deletions(-)
delete mode 100644 arch/arm/boot/compressed/head-shmobile.S
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot.h
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot_macros.h
diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile
index 7a13aebacf81d47c..3f9a9ebc77c389bb 100644
--- a/arch/arm/boot/compressed/Makefile
+++ b/arch/arm/boot/compressed/Makefile
@@ -51,10 +51,6 @@ else
endif
endif
-ifeq ($(CONFIG_ARCH_SHMOBILE_LEGACY),y)
-OBJS += head-shmobile.o
-endif
-
#
# We now have a PIC decompressor implementation. Decompressors running
# from RAM should not define ZTEXTADDR. Decompressors running directly
diff --git a/arch/arm/boot/compressed/head-shmobile.S b/arch/arm/boot/compressed/head-shmobile.S
deleted file mode 100644
index 22a75259faa32996..0000000000000000
--- a/arch/arm/boot/compressed/head-shmobile.S
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * The head-file for SH-Mobile ARM platforms
- *
- * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- * Simon Horman <horms@verge.net.au>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#ifdef CONFIG_ZBOOT_ROM
-
- .section ".start", "ax"
-
- /* load board-specific initialization code */
-#include <mach/zboot.h>
-
- adr r0, dtb_info
- ldmia r0, {r1, r3, r4, r5, r7}
-
- sub r0, r0, r1 @ calculate the delta offset
- add r5, r5, r0 @ _edata
-
- ldr lr, [r5, #0] @ check if valid DTB is present
- cmp lr, r3
- bne 0f
-
- add r9, r7, #31 @ rounded up to a multiple
- bic r9, r9, #31 @ ... of 32 bytes
-
- add r6, r9, r5 @ copy from _edata
- add r9, r9, r4 @ to MEMORY_START
-
-1: ldmdb r6!, {r0 - r3, r10 - r12, lr}
- cmp r6, r5
- stmdb r9!, {r0 - r3, r10 - r12, lr}
- bhi 1b
-
- /* Success: Zero board ID, pointer to start of memory for atag/dtb */
- mov r7, #0
- mov r8, r4
- b 2f
-
- .align 2
-dtb_info:
- .word dtb_info
-#ifndef __ARMEB__
- .word 0xedfe0dd0 @ sig is 0xd00dfeed big endian
-#else
- .word 0xd00dfeed
-#endif
- .word MEMORY_START
- .word _edata
- .word 0x4000 @ maximum DTB size
-0:
- /* Failure: Zero board ID, NULL atag/dtb */
- mov r7, #0
- mov r8, #0 @ pass null pointer as atag
-2 :
-
-#endif /* CONFIG_ZBOOT_ROM */
diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h
deleted file mode 100644
index 80f599f4b5ab5733..0000000000000000
--- a/arch/arm/mach-shmobile/include/mach/zboot.h
+++ /dev/null
@@ -1,14 +0,0 @@
-#ifndef ZBOOT_H
-#define ZBOOT_H
-
-#include <mach/zboot_macros.h>
-
-/**************************************************
- *
- * board specific settings
- *
- **************************************************/
-
-#error "unsupported board."
-
-#endif /* ZBOOT_H */
diff --git a/arch/arm/mach-shmobile/include/mach/zboot_macros.h b/arch/arm/mach-shmobile/include/mach/zboot_macros.h
deleted file mode 100644
index 14fd3d538e9aa11a..0000000000000000
--- a/arch/arm/mach-shmobile/include/mach/zboot_macros.h
+++ /dev/null
@@ -1,108 +0,0 @@
-#ifndef __ZBOOT_MACRO_H
-#define __ZBOOT_MACRO_H
-
-/* The LIST command is used to include comments in the script */
-.macro LIST comment
-.endm
-
-/* The ED command is used to write a 32-bit word */
-.macro ED, addr, data
- LDR r0, 1f
- LDR r1, 2f
- STR r1, [r0]
- B 3f
-1 : .long \addr
-2 : .long \data
-3 :
-.endm
-
-/* The EW command is used to write a 16-bit word */
-.macro EW, addr, data
- LDR r0, 1f
- LDR r1, 2f
- STRH r1, [r0]
- B 3f
-1 : .long \addr
-2 : .long \data
-3 :
-.endm
-
-/* The EB command is used to write an 8-bit word */
-.macro EB, addr, data
- LDR r0, 1f
- LDR r1, 2f
- STRB r1, [r0]
- B 3f
-1 : .long \addr
-2 : .long \data
-3 :
-.endm
-
-/* The WAIT command is used to delay the execution */
-.macro WAIT, time, reg
- LDR r1, 1f
- LDR r0, 2f
- STR r0, [r1]
-10 :
- LDR r0, [r1]
- CMP r0, #0x00000000
- BNE 10b
- NOP
- B 3f
-1 : .long \reg
-2 : .long \time * 100
-3 :
-.endm
-
-/* The DD command is used to read a 32-bit word */
-.macro DD, start, end
- LDR r1, 1f
- B 2f
-1 : .long \start
-2 :
-.endm
-
-/* loop until a given value has been read (with mask) */
-.macro WAIT_MASK, addr, data, cmp
- LDR r0, 2f
- LDR r1, 3f
- LDR r2, 4f
-1:
- LDR r3, [r0, #0]
- AND r3, r1, r3
- CMP r2, r3
- BNE 1b
- B 5f
-2: .long \addr
-3: .long \data
-4: .long \cmp
-5:
-.endm
-
-/* read 32-bit value from addr, "or" an immediate and write back */
-.macro ED_OR, addr, data
- LDR r4, 1f
- LDR r5, 2f
- LDR r6, [r4]
- ORR r5, r6, r5
- STR r5, [r4]
- B 3f
-1: .long \addr
-2: .long \data
-3:
-.endm
-
-/* read 32-bit value from addr, "and" an immediate and write back */
-.macro ED_AND, addr, data
- LDR r4, 1f
- LDR r5, 2f
- LDR r6, [r4]
- AND r5, r6, r5
- STR r5, [r4]
- B 3f
-1: .long \addr
-2: .long \data
-3:
-.endm
-
-#endif /* __ZBOOT_MACRO_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 11/15] ARM: shmobile: Remove obsolete zboot support
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
The last user of the zboot code was the KZM-A9-GT legacy board code,
which has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm/boot/compressed/Makefile | 4 -
arch/arm/boot/compressed/head-shmobile.S | 71 --------------
arch/arm/mach-shmobile/include/mach/zboot.h | 14 ---
arch/arm/mach-shmobile/include/mach/zboot_macros.h | 108 ---------------------
4 files changed, 197 deletions(-)
delete mode 100644 arch/arm/boot/compressed/head-shmobile.S
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot.h
delete mode 100644 arch/arm/mach-shmobile/include/mach/zboot_macros.h
diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile
index 7a13aebacf81d47c..3f9a9ebc77c389bb 100644
--- a/arch/arm/boot/compressed/Makefile
+++ b/arch/arm/boot/compressed/Makefile
@@ -51,10 +51,6 @@ else
endif
endif
-ifeq ($(CONFIG_ARCH_SHMOBILE_LEGACY),y)
-OBJS += head-shmobile.o
-endif
-
#
# We now have a PIC decompressor implementation. Decompressors running
# from RAM should not define ZTEXTADDR. Decompressors running directly
diff --git a/arch/arm/boot/compressed/head-shmobile.S b/arch/arm/boot/compressed/head-shmobile.S
deleted file mode 100644
index 22a75259faa32996..0000000000000000
--- a/arch/arm/boot/compressed/head-shmobile.S
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * The head-file for SH-Mobile ARM platforms
- *
- * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- * Simon Horman <horms@verge.net.au>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#ifdef CONFIG_ZBOOT_ROM
-
- .section ".start", "ax"
-
- /* load board-specific initialization code */
-#include <mach/zboot.h>
-
- adr r0, dtb_info
- ldmia r0, {r1, r3, r4, r5, r7}
-
- sub r0, r0, r1 @ calculate the delta offset
- add r5, r5, r0 @ _edata
-
- ldr lr, [r5, #0] @ check if valid DTB is present
- cmp lr, r3
- bne 0f
-
- add r9, r7, #31 @ rounded up to a multiple
- bic r9, r9, #31 @ ... of 32 bytes
-
- add r6, r9, r5 @ copy from _edata
- add r9, r9, r4 @ to MEMORY_START
-
-1: ldmdb r6!, {r0 - r3, r10 - r12, lr}
- cmp r6, r5
- stmdb r9!, {r0 - r3, r10 - r12, lr}
- bhi 1b
-
- /* Success: Zero board ID, pointer to start of memory for atag/dtb */
- mov r7, #0
- mov r8, r4
- b 2f
-
- .align 2
-dtb_info:
- .word dtb_info
-#ifndef __ARMEB__
- .word 0xedfe0dd0 @ sig is 0xd00dfeed big endian
-#else
- .word 0xd00dfeed
-#endif
- .word MEMORY_START
- .word _edata
- .word 0x4000 @ maximum DTB size
-0:
- /* Failure: Zero board ID, NULL atag/dtb */
- mov r7, #0
- mov r8, #0 @ pass null pointer as atag
-2 :
-
-#endif /* CONFIG_ZBOOT_ROM */
diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h
deleted file mode 100644
index 80f599f4b5ab5733..0000000000000000
--- a/arch/arm/mach-shmobile/include/mach/zboot.h
+++ /dev/null
@@ -1,14 +0,0 @@
-#ifndef ZBOOT_H
-#define ZBOOT_H
-
-#include <mach/zboot_macros.h>
-
-/**************************************************
- *
- * board specific settings
- *
- **************************************************/
-
-#error "unsupported board."
-
-#endif /* ZBOOT_H */
diff --git a/arch/arm/mach-shmobile/include/mach/zboot_macros.h b/arch/arm/mach-shmobile/include/mach/zboot_macros.h
deleted file mode 100644
index 14fd3d538e9aa11a..0000000000000000
--- a/arch/arm/mach-shmobile/include/mach/zboot_macros.h
+++ /dev/null
@@ -1,108 +0,0 @@
-#ifndef __ZBOOT_MACRO_H
-#define __ZBOOT_MACRO_H
-
-/* The LIST command is used to include comments in the script */
-.macro LIST comment
-.endm
-
-/* The ED command is used to write a 32-bit word */
-.macro ED, addr, data
- LDR r0, 1f
- LDR r1, 2f
- STR r1, [r0]
- B 3f
-1 : .long \addr
-2 : .long \data
-3 :
-.endm
-
-/* The EW command is used to write a 16-bit word */
-.macro EW, addr, data
- LDR r0, 1f
- LDR r1, 2f
- STRH r1, [r0]
- B 3f
-1 : .long \addr
-2 : .long \data
-3 :
-.endm
-
-/* The EB command is used to write an 8-bit word */
-.macro EB, addr, data
- LDR r0, 1f
- LDR r1, 2f
- STRB r1, [r0]
- B 3f
-1 : .long \addr
-2 : .long \data
-3 :
-.endm
-
-/* The WAIT command is used to delay the execution */
-.macro WAIT, time, reg
- LDR r1, 1f
- LDR r0, 2f
- STR r0, [r1]
-10 :
- LDR r0, [r1]
- CMP r0, #0x00000000
- BNE 10b
- NOP
- B 3f
-1 : .long \reg
-2 : .long \time * 100
-3 :
-.endm
-
-/* The DD command is used to read a 32-bit word */
-.macro DD, start, end
- LDR r1, 1f
- B 2f
-1 : .long \start
-2 :
-.endm
-
-/* loop until a given value has been read (with mask) */
-.macro WAIT_MASK, addr, data, cmp
- LDR r0, 2f
- LDR r1, 3f
- LDR r2, 4f
-1:
- LDR r3, [r0, #0]
- AND r3, r1, r3
- CMP r2, r3
- BNE 1b
- B 5f
-2: .long \addr
-3: .long \data
-4: .long \cmp
-5:
-.endm
-
-/* read 32-bit value from addr, "or" an immediate and write back */
-.macro ED_OR, addr, data
- LDR r4, 1f
- LDR r5, 2f
- LDR r6, [r4]
- ORR r5, r6, r5
- STR r5, [r4]
- B 3f
-1: .long \addr
-2: .long \data
-3:
-.endm
-
-/* read 32-bit value from addr, "and" an immediate and write back */
-.macro ED_AND, addr, data
- LDR r4, 1f
- LDR r5, 2f
- LDR r6, [r4]
- AND r5, r6, r5
- STR r5, [r4]
- B 3f
-1: .long \addr
-2: .long \data
-3:
-.endm
-
-#endif /* __ZBOOT_MACRO_H */
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 12/15] pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the sh73a0 legacy board code, sh73a0 is only
supported in generic ARM multi-platform builds. Hence
CONFIG_ARCH_MULTIPLATFORM is always set, and the check can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy sh73a0 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/pfc-sh73a0.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/pfc-sh73a0.c b/drivers/pinctrl/sh-pfc/pfc-sh73a0.c
index d2efbfb776ac57d6..097526576f88181f 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh73a0.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh73a0.c
@@ -26,10 +26,6 @@
#include <linux/regulator/machine.h>
#include <linux/slab.h>
-#ifndef CONFIG_ARCH_MULTIPLATFORM
-#include <mach/irqs.h>
-#endif
-
#include "core.h"
#include "sh_pfc.h"
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 12/15] pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the sh73a0 legacy board code, sh73a0 is only
supported in generic ARM multi-platform builds. Hence
CONFIG_ARCH_MULTIPLATFORM is always set, and the check can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy sh73a0 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/pfc-sh73a0.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/pfc-sh73a0.c b/drivers/pinctrl/sh-pfc/pfc-sh73a0.c
index d2efbfb776ac57d6..097526576f88181f 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh73a0.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh73a0.c
@@ -26,10 +26,6 @@
#include <linux/regulator/machine.h>
#include <linux/slab.h>
-#ifndef CONFIG_ARCH_MULTIPLATFORM
-#include <mach/irqs.h>
-#endif
-
#include "core.h"
#include "sh_pfc.h"
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 13/15] pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the sh73a0 legacy board code, sh73a0 is only
supported in generic DT-only ARM multi-platform builds. The driver
doesn't need to match platform devices by name anymore, hence remove the
corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy sh73a0 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/core.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/core.c b/drivers/pinctrl/sh-pfc/core.c
index 96556362b28f2caa..3ff523e58c38d123 100644
--- a/drivers/pinctrl/sh-pfc/core.c
+++ b/drivers/pinctrl/sh-pfc/core.c
@@ -603,9 +603,6 @@ static const struct platform_device_id sh_pfc_id_table[] = {
#ifdef CONFIG_PINCTRL_PFC_SH7269
{ "pfc-sh7269", (kernel_ulong_t)&sh7269_pinmux_info },
#endif
-#ifdef CONFIG_PINCTRL_PFC_SH73A0
- { "pfc-sh73a0", (kernel_ulong_t)&sh73a0_pinmux_info },
-#endif
#ifdef CONFIG_PINCTRL_PFC_SH7720
{ "pfc-sh7720", (kernel_ulong_t)&sh7720_pinmux_info },
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 13/15] pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the sh73a0 legacy board code, sh73a0 is only
supported in generic DT-only ARM multi-platform builds. The driver
doesn't need to match platform devices by name anymore, hence remove the
corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy sh73a0 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/core.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/core.c b/drivers/pinctrl/sh-pfc/core.c
index 96556362b28f2caa..3ff523e58c38d123 100644
--- a/drivers/pinctrl/sh-pfc/core.c
+++ b/drivers/pinctrl/sh-pfc/core.c
@@ -603,9 +603,6 @@ static const struct platform_device_id sh_pfc_id_table[] = {
#ifdef CONFIG_PINCTRL_PFC_SH7269
{ "pfc-sh7269", (kernel_ulong_t)&sh7269_pinmux_info },
#endif
-#ifdef CONFIG_PINCTRL_PFC_SH73A0
- { "pfc-sh73a0", (kernel_ulong_t)&sh73a0_pinmux_info },
-#endif
#ifdef CONFIG_PINCTRL_PFC_SH7720
{ "pfc-sh7720", (kernel_ulong_t)&sh7720_pinmux_info },
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 14/15] pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the r8a7740 legacy board code, r8a7740 is only
supported in generic ARM multi-platform builds. Hence
CONFIG_ARCH_MULTIPLATFORM is always set, and the check can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy r8a7740 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/pfc-r8a7740.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7740.c b/drivers/pinctrl/sh-pfc/pfc-r8a7740.c
index d0bb1459783a16d2..82ef1862dd1ba808 100644
--- a/drivers/pinctrl/sh-pfc/pfc-r8a7740.c
+++ b/drivers/pinctrl/sh-pfc/pfc-r8a7740.c
@@ -22,10 +22,6 @@
#include <linux/kernel.h>
#include <linux/pinctrl/pinconf-generic.h>
-#ifndef CONFIG_ARCH_MULTIPLATFORM
-#include <mach/irqs.h>
-#endif
-
#include "core.h"
#include "sh_pfc.h"
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 14/15] pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the r8a7740 legacy board code, r8a7740 is only
supported in generic ARM multi-platform builds. Hence
CONFIG_ARCH_MULTIPLATFORM is always set, and the check can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy r8a7740 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/pfc-r8a7740.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7740.c b/drivers/pinctrl/sh-pfc/pfc-r8a7740.c
index d0bb1459783a16d2..82ef1862dd1ba808 100644
--- a/drivers/pinctrl/sh-pfc/pfc-r8a7740.c
+++ b/drivers/pinctrl/sh-pfc/pfc-r8a7740.c
@@ -22,10 +22,6 @@
#include <linux/kernel.h>
#include <linux/pinctrl/pinconf-generic.h>
-#ifndef CONFIG_ARCH_MULTIPLATFORM
-#include <mach/irqs.h>
-#endif
-
#include "core.h"
#include "sh_pfc.h"
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 15/15] pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
2015-06-17 9:31 ` Geert Uytterhoeven
@ 2015-06-17 9:31 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the r8a7740 legacy board code, r8a7740 is only
supported in generic DT-only ARM multi-platform builds. The driver
doesn't need to match platform devices by name anymore, hence remove the
corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy r8a7740 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/core.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/core.c b/drivers/pinctrl/sh-pfc/core.c
index 3ff523e58c38d123..aeeeb76327c0684e 100644
--- a/drivers/pinctrl/sh-pfc/core.c
+++ b/drivers/pinctrl/sh-pfc/core.c
@@ -585,9 +585,6 @@ static int sh_pfc_remove(struct platform_device *pdev)
}
static const struct platform_device_id sh_pfc_id_table[] = {
-#ifdef CONFIG_PINCTRL_PFC_R8A7740
- { "pfc-r8a7740", (kernel_ulong_t)&r8a7740_pinmux_info },
-#endif
#ifdef CONFIG_PINCTRL_PFC_R8A7778
{ "pfc-r8a7778", (kernel_ulong_t)&r8a7778_pinmux_info },
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH 15/15] pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
@ 2015-06-17 9:31 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-17 9:31 UTC (permalink / raw)
To: linux-arm-kernel
Since the removal of the r8a7740 legacy board code, r8a7740 is only
supported in generic DT-only ARM multi-platform builds. The driver
doesn't need to match platform devices by name anymore, hence remove the
corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
---
Please do not apply until the legacy r8a7740 SoC code has been removed.
Or just provide an ack, so Simon can apply it when appropriate.
---
drivers/pinctrl/sh-pfc/core.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/core.c b/drivers/pinctrl/sh-pfc/core.c
index 3ff523e58c38d123..aeeeb76327c0684e 100644
--- a/drivers/pinctrl/sh-pfc/core.c
+++ b/drivers/pinctrl/sh-pfc/core.c
@@ -585,9 +585,6 @@ static int sh_pfc_remove(struct platform_device *pdev)
}
static const struct platform_device_id sh_pfc_id_table[] = {
-#ifdef CONFIG_PINCTRL_PFC_R8A7740
- { "pfc-r8a7740", (kernel_ulong_t)&r8a7740_pinmux_info },
-#endif
#ifdef CONFIG_PINCTRL_PFC_R8A7778
{ "pfc-r8a7778", (kernel_ulong_t)&r8a7778_pinmux_info },
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
2015-06-17 9:31 ` Geert Uytterhoeven
(?)
@ 2015-06-19 3:41 ` Simon Horman
-1 siblings, 0 replies; 50+ messages in thread
From: Simon Horman @ 2015-06-19 3:41 UTC (permalink / raw)
To: linux-arm-kernel
[ CC Linus, Laurent, linux-gpio ]
On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> Hi Simon, Magnus,
>
> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> A1 (r8a7740) multi-platform kernels.
>
> Lacking areas are:
> - USB (it does't work in legacy, neither),
> - HDMI on armadillo (it doesn't work in legacy, neither),
> - Camera on armadillo (we don't care),
> - LCDC:
> - on armadillo, this is supported by the board staging code,
> - on kzm9g, the LCDC is wired to the legacy INTC, which is not
> planned to be supported with DT,
> - DMAC/IPMMU (no DT bindings are planned).
>
> Hence this patch series removes legacy board and SoC code for
> sh73a0/kzm9g and r8a7740/armadillo.
>
> It consists of 4 parts:
> - Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
> dtb) and sh73a0,
> - Patches 5-8 remove legacy support for armadillo (board code,
> defconfig, dtb) and r8a7740,
> - Patches 9-11 remove generic shmobile support code (dma-register.h,
> legacy PM Domains, zboot) that became unused by the removal of
> legacy sh73a0/kzm9g and r8a7740/armadillo,
> - Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
> pinctrl drivers.
>
> Dependencies:
> - This is against next-20150617,
> - To keep up with existing LCDC functionality for armadillo-legacy,
> the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
> 0/7] staging: board: armadillo800eva: Board staging for
> sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
> However, it can be applied as-is now, and board staging can he
> handled in parallel (if at all).
>
> Thanks for applying!
>
> Geert Uytterhoeven (15):
> ARM: shmobile: Remove legacy board code for KZM-A9-GT
> ARM: shmobile: Remove legacy kzm9g_defconfig
> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> ARM: shmobile: Remove legacy armadillo800eva_defconfig
> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> ARM: shmobile: Remove unused dma-register.h
> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> ARM: shmobile: Remove obsolete zboot support
I have queued up the above patches for v4.3.
> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
As the above patches are sh-pfc patches they would typically
be steered through Linus's tree via Laurent. If they wish
to take that path then I'm happy for this to be attached:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
FWIW the above path is the one that the removal of mackerel/sh7372 took.
Alternatively, I am happy to take the above sh-pfc patches through
my tree but I would like to do so with an Ack from at least Linus.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 3:41 ` Simon Horman
0 siblings, 0 replies; 50+ messages in thread
From: Simon Horman @ 2015-06-19 3:41 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Arnd Bergmann, linux-sh, Linus Walleij, Magnus Damm, linux-gpio,
Laurent Pinchart, linux-arm-kernel
[ CC Linus, Laurent, linux-gpio ]
On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> Hi Simon, Magnus,
>
> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> A1 (r8a7740) multi-platform kernels.
>
> Lacking areas are:
> - USB (it does't work in legacy, neither),
> - HDMI on armadillo (it doesn't work in legacy, neither),
> - Camera on armadillo (we don't care),
> - LCDC:
> - on armadillo, this is supported by the board staging code,
> - on kzm9g, the LCDC is wired to the legacy INTC, which is not
> planned to be supported with DT,
> - DMAC/IPMMU (no DT bindings are planned).
>
> Hence this patch series removes legacy board and SoC code for
> sh73a0/kzm9g and r8a7740/armadillo.
>
> It consists of 4 parts:
> - Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
> dtb) and sh73a0,
> - Patches 5-8 remove legacy support for armadillo (board code,
> defconfig, dtb) and r8a7740,
> - Patches 9-11 remove generic shmobile support code (dma-register.h,
> legacy PM Domains, zboot) that became unused by the removal of
> legacy sh73a0/kzm9g and r8a7740/armadillo,
> - Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
> pinctrl drivers.
>
> Dependencies:
> - This is against next-20150617,
> - To keep up with existing LCDC functionality for armadillo-legacy,
> the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
> 0/7] staging: board: armadillo800eva: Board staging for
> sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
> However, it can be applied as-is now, and board staging can he
> handled in parallel (if at all).
>
> Thanks for applying!
>
> Geert Uytterhoeven (15):
> ARM: shmobile: Remove legacy board code for KZM-A9-GT
> ARM: shmobile: Remove legacy kzm9g_defconfig
> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> ARM: shmobile: Remove legacy armadillo800eva_defconfig
> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> ARM: shmobile: Remove unused dma-register.h
> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> ARM: shmobile: Remove obsolete zboot support
I have queued up the above patches for v4.3.
> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
As the above patches are sh-pfc patches they would typically
be steered through Linus's tree via Laurent. If they wish
to take that path then I'm happy for this to be attached:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
FWIW the above path is the one that the removal of mackerel/sh7372 took.
Alternatively, I am happy to take the above sh-pfc patches through
my tree but I would like to do so with an Ack from at least Linus.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 3:41 ` Simon Horman
0 siblings, 0 replies; 50+ messages in thread
From: Simon Horman @ 2015-06-19 3:41 UTC (permalink / raw)
To: linux-arm-kernel
[ CC Linus, Laurent, linux-gpio ]
On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> Hi Simon, Magnus,
>
> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> A1 (r8a7740) multi-platform kernels.
>
> Lacking areas are:
> - USB (it does't work in legacy, neither),
> - HDMI on armadillo (it doesn't work in legacy, neither),
> - Camera on armadillo (we don't care),
> - LCDC:
> - on armadillo, this is supported by the board staging code,
> - on kzm9g, the LCDC is wired to the legacy INTC, which is not
> planned to be supported with DT,
> - DMAC/IPMMU (no DT bindings are planned).
>
> Hence this patch series removes legacy board and SoC code for
> sh73a0/kzm9g and r8a7740/armadillo.
>
> It consists of 4 parts:
> - Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
> dtb) and sh73a0,
> - Patches 5-8 remove legacy support for armadillo (board code,
> defconfig, dtb) and r8a7740,
> - Patches 9-11 remove generic shmobile support code (dma-register.h,
> legacy PM Domains, zboot) that became unused by the removal of
> legacy sh73a0/kzm9g and r8a7740/armadillo,
> - Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
> pinctrl drivers.
>
> Dependencies:
> - This is against next-20150617,
> - To keep up with existing LCDC functionality for armadillo-legacy,
> the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
> 0/7] staging: board: armadillo800eva: Board staging for
> sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
> However, it can be applied as-is now, and board staging can he
> handled in parallel (if at all).
>
> Thanks for applying!
>
> Geert Uytterhoeven (15):
> ARM: shmobile: Remove legacy board code for KZM-A9-GT
> ARM: shmobile: Remove legacy kzm9g_defconfig
> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> ARM: shmobile: Remove legacy armadillo800eva_defconfig
> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> ARM: shmobile: Remove unused dma-register.h
> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> ARM: shmobile: Remove obsolete zboot support
I have queued up the above patches for v4.3.
> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
As the above patches are sh-pfc patches they would typically
be steered through Linus's tree via Laurent. If they wish
to take that path then I'm happy for this to be attached:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
FWIW the above path is the one that the removal of mackerel/sh7372 took.
Alternatively, I am happy to take the above sh-pfc patches through
my tree but I would like to do so with an Ack from at least Linus.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
2015-06-19 3:41 ` Simon Horman
(?)
@ 2015-06-19 7:30 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-19 7:30 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
> [ CC Linus, Laurent, linux-gpio ]
>
> On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
>> Hi Simon, Magnus,
>>
>> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
>> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
>> A1 (r8a7740) multi-platform kernels.
>> Hence this patch series removes legacy board and SoC code for
>> sh73a0/kzm9g and r8a7740/armadillo.
>> Geert Uytterhoeven (15):
>> ARM: shmobile: Remove legacy board code for KZM-A9-GT
>> ARM: shmobile: Remove legacy kzm9g_defconfig
>> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
>> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
>> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
>> ARM: shmobile: Remove legacy armadillo800eva_defconfig
>> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
>> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
>> ARM: shmobile: Remove unused dma-register.h
>> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
>> ARM: shmobile: Remove obsolete zboot support
>
> I have queued up the above patches for v4.3.
Thanks!
>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>
> As the above patches are sh-pfc patches they would typically
> be steered through Linus's tree via Laurent. If they wish
> to take that path then I'm happy for this to be attached:
>
> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>
> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>
> Alternatively, I am happy to take the above sh-pfc patches through
> my tree but I would like to do so with an Ack from at least Linus.
I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
patches from getting applied prematurely.
But things have gone more smoothly (esp. w.r.t. board staging) than expected,
which is always pleasant.
I can resend later, I have a few more areas of sh73a0/r8a7740 cleanup
outside arch/arm/mach-shmobile waiting anyway...
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 7:30 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-19 7:30 UTC (permalink / raw)
To: Simon Horman
Cc: Geert Uytterhoeven, Magnus Damm, Arnd Bergmann, Linux-sh list,
linux-arm-kernel, Laurent Pinchart, Linus Walleij, linux-gpio
On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
> [ CC Linus, Laurent, linux-gpio ]
>
> On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
>> Hi Simon, Magnus,
>>
>> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
>> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
>> A1 (r8a7740) multi-platform kernels.
>> Hence this patch series removes legacy board and SoC code for
>> sh73a0/kzm9g and r8a7740/armadillo.
>> Geert Uytterhoeven (15):
>> ARM: shmobile: Remove legacy board code for KZM-A9-GT
>> ARM: shmobile: Remove legacy kzm9g_defconfig
>> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
>> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
>> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
>> ARM: shmobile: Remove legacy armadillo800eva_defconfig
>> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
>> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
>> ARM: shmobile: Remove unused dma-register.h
>> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
>> ARM: shmobile: Remove obsolete zboot support
>
> I have queued up the above patches for v4.3.
Thanks!
>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>
> As the above patches are sh-pfc patches they would typically
> be steered through Linus's tree via Laurent. If they wish
> to take that path then I'm happy for this to be attached:
>
> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>
> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>
> Alternatively, I am happy to take the above sh-pfc patches through
> my tree but I would like to do so with an Ack from at least Linus.
I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
patches from getting applied prematurely.
But things have gone more smoothly (esp. w.r.t. board staging) than expected,
which is always pleasant.
I can resend later, I have a few more areas of sh73a0/r8a7740 cleanup
outside arch/arm/mach-shmobile waiting anyway...
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 7:30 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-06-19 7:30 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
> [ CC Linus, Laurent, linux-gpio ]
>
> On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
>> Hi Simon, Magnus,
>>
>> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
>> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
>> A1 (r8a7740) multi-platform kernels.
>> Hence this patch series removes legacy board and SoC code for
>> sh73a0/kzm9g and r8a7740/armadillo.
>> Geert Uytterhoeven (15):
>> ARM: shmobile: Remove legacy board code for KZM-A9-GT
>> ARM: shmobile: Remove legacy kzm9g_defconfig
>> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
>> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
>> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
>> ARM: shmobile: Remove legacy armadillo800eva_defconfig
>> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
>> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
>> ARM: shmobile: Remove unused dma-register.h
>> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
>> ARM: shmobile: Remove obsolete zboot support
>
> I have queued up the above patches for v4.3.
Thanks!
>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>
> As the above patches are sh-pfc patches they would typically
> be steered through Linus's tree via Laurent. If they wish
> to take that path then I'm happy for this to be attached:
>
> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>
> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>
> Alternatively, I am happy to take the above sh-pfc patches through
> my tree but I would like to do so with an Ack from at least Linus.
I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
patches from getting applied prematurely.
But things have gone more smoothly (esp. w.r.t. board staging) than expected,
which is always pleasant.
I can resend later, I have a few more areas of sh73a0/r8a7740 cleanup
outside arch/arm/mach-shmobile waiting anyway...
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
2015-06-19 7:30 ` Geert Uytterhoeven
(?)
@ 2015-06-19 8:17 ` Simon Horman
-1 siblings, 0 replies; 50+ messages in thread
From: Simon Horman @ 2015-06-19 8:17 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 19, 2015 at 09:30:56AM +0200, Geert Uytterhoeven wrote:
> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
> > [ CC Linus, Laurent, linux-gpio ]
> >
> > On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> >> Hi Simon, Magnus,
> >>
> >> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> >> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> >> A1 (r8a7740) multi-platform kernels.
>
> >> Hence this patch series removes legacy board and SoC code for
> >> sh73a0/kzm9g and r8a7740/armadillo.
>
> >> Geert Uytterhoeven (15):
> >> ARM: shmobile: Remove legacy board code for KZM-A9-GT
> >> ARM: shmobile: Remove legacy kzm9g_defconfig
> >> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> >> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> >> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> >> ARM: shmobile: Remove legacy armadillo800eva_defconfig
> >> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> >> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> >> ARM: shmobile: Remove unused dma-register.h
> >> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> >> ARM: shmobile: Remove obsolete zboot support
> >
> > I have queued up the above patches for v4.3.
>
> Thanks!
>
> >> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> >> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> >> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> >> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
> >
> > As the above patches are sh-pfc patches they would typically
> > be steered through Linus's tree via Laurent. If they wish
> > to take that path then I'm happy for this to be attached:
> >
> > Acked-by: Simon Horman <horms+renesas@verge.net.au>
> >
> > FWIW the above path is the one that the removal of mackerel/sh7372 took.
> >
> > Alternatively, I am happy to take the above sh-pfc patches through
> > my tree but I would like to do so with an Ack from at least Linus.
>
> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
> patches from getting applied prematurely.
> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
> which is always pleasant.
>
> I can resend later, I have a few more areas of sh73a0/r8a7740 cleanup
> outside arch/arm/mach-shmobile waiting anyway...
I'm happy with whatever timing you think is best.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 8:17 ` Simon Horman
0 siblings, 0 replies; 50+ messages in thread
From: Simon Horman @ 2015-06-19 8:17 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Geert Uytterhoeven, Magnus Damm, Arnd Bergmann, Linux-sh list,
linux-arm-kernel, Laurent Pinchart, Linus Walleij, linux-gpio
On Fri, Jun 19, 2015 at 09:30:56AM +0200, Geert Uytterhoeven wrote:
> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
> > [ CC Linus, Laurent, linux-gpio ]
> >
> > On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> >> Hi Simon, Magnus,
> >>
> >> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> >> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> >> A1 (r8a7740) multi-platform kernels.
>
> >> Hence this patch series removes legacy board and SoC code for
> >> sh73a0/kzm9g and r8a7740/armadillo.
>
> >> Geert Uytterhoeven (15):
> >> ARM: shmobile: Remove legacy board code for KZM-A9-GT
> >> ARM: shmobile: Remove legacy kzm9g_defconfig
> >> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> >> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> >> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> >> ARM: shmobile: Remove legacy armadillo800eva_defconfig
> >> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> >> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> >> ARM: shmobile: Remove unused dma-register.h
> >> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> >> ARM: shmobile: Remove obsolete zboot support
> >
> > I have queued up the above patches for v4.3.
>
> Thanks!
>
> >> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> >> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> >> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> >> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
> >
> > As the above patches are sh-pfc patches they would typically
> > be steered through Linus's tree via Laurent. If they wish
> > to take that path then I'm happy for this to be attached:
> >
> > Acked-by: Simon Horman <horms+renesas@verge.net.au>
> >
> > FWIW the above path is the one that the removal of mackerel/sh7372 took.
> >
> > Alternatively, I am happy to take the above sh-pfc patches through
> > my tree but I would like to do so with an Ack from at least Linus.
>
> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
> patches from getting applied prematurely.
> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
> which is always pleasant.
>
> I can resend later, I have a few more areas of sh73a0/r8a7740 cleanup
> outside arch/arm/mach-shmobile waiting anyway...
I'm happy with whatever timing you think is best.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 8:17 ` Simon Horman
0 siblings, 0 replies; 50+ messages in thread
From: Simon Horman @ 2015-06-19 8:17 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 19, 2015 at 09:30:56AM +0200, Geert Uytterhoeven wrote:
> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
> > [ CC Linus, Laurent, linux-gpio ]
> >
> > On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> >> Hi Simon, Magnus,
> >>
> >> The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> >> supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> >> A1 (r8a7740) multi-platform kernels.
>
> >> Hence this patch series removes legacy board and SoC code for
> >> sh73a0/kzm9g and r8a7740/armadillo.
>
> >> Geert Uytterhoeven (15):
> >> ARM: shmobile: Remove legacy board code for KZM-A9-GT
> >> ARM: shmobile: Remove legacy kzm9g_defconfig
> >> ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> >> ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> >> ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> >> ARM: shmobile: Remove legacy armadillo800eva_defconfig
> >> ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> >> ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> >> ARM: shmobile: Remove unused dma-register.h
> >> ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> >> ARM: shmobile: Remove obsolete zboot support
> >
> > I have queued up the above patches for v4.3.
>
> Thanks!
>
> >> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> >> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> >> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> >> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
> >
> > As the above patches are sh-pfc patches they would typically
> > be steered through Linus's tree via Laurent. If they wish
> > to take that path then I'm happy for this to be attached:
> >
> > Acked-by: Simon Horman <horms+renesas@verge.net.au>
> >
> > FWIW the above path is the one that the removal of mackerel/sh7372 took.
> >
> > Alternatively, I am happy to take the above sh-pfc patches through
> > my tree but I would like to do so with an Ack from at least Linus.
>
> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
> patches from getting applied prematurely.
> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
> which is always pleasant.
>
> I can resend later, I have a few more areas of sh73a0/r8a7740 cleanup
> outside arch/arm/mach-shmobile waiting anyway...
I'm happy with whatever timing you think is best.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
2015-06-19 3:41 ` Simon Horman
(?)
@ 2015-06-19 9:05 ` Laurent Pinchart
-1 siblings, 0 replies; 50+ messages in thread
From: Laurent Pinchart @ 2015-06-19 9:05 UTC (permalink / raw)
To: linux-arm-kernel
Hi Simon,
On Friday 19 June 2015 12:41:00 Simon Horman wrote:
> [ CC Linus, Laurent, linux-gpio ]
>
> On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> > Hi Simon, Magnus,
> >
> > The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> > supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> > A1 (r8a7740) multi-platform kernels.
> >
> > Lacking areas are:
> > - USB (it does't work in legacy, neither),
> > - HDMI on armadillo (it doesn't work in legacy, neither),
> > - Camera on armadillo (we don't care),
> >
> > - LCDC:
> > - on armadillo, this is supported by the board staging code,
> > - on kzm9g, the LCDC is wired to the legacy INTC, which is not
> >
> > planned to be supported with DT,
> >
> > - DMAC/IPMMU (no DT bindings are planned).
> >
> > Hence this patch series removes legacy board and SoC code for
> > sh73a0/kzm9g and r8a7740/armadillo.
> >
> > It consists of 4 parts:
> > - Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
> >
> > dtb) and sh73a0,
> >
> > - Patches 5-8 remove legacy support for armadillo (board code,
> >
> > defconfig, dtb) and r8a7740,
> >
> > - Patches 9-11 remove generic shmobile support code (dma-register.h,
> >
> > legacy PM Domains, zboot) that became unused by the removal of
> > legacy sh73a0/kzm9g and r8a7740/armadillo,
> >
> > - Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
> >
> > pinctrl drivers.
> >
> > Dependencies:
> > - This is against next-20150617,
> > - To keep up with existing LCDC functionality for armadillo-legacy,
> >
> > the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
> > 0/7] staging: board: armadillo800eva: Board staging for
> > sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
> > However, it can be applied as-is now, and board staging can he
> > handled in parallel (if at all).
> >
> > Thanks for applying!
> >
> > Geert Uytterhoeven (15):
> > ARM: shmobile: Remove legacy board code for KZM-A9-GT
> > ARM: shmobile: Remove legacy kzm9g_defconfig
> > ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> > ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> > ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> > ARM: shmobile: Remove legacy armadillo800eva_defconfig
> > ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> > ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> > ARM: shmobile: Remove unused dma-register.h
> > ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> > ARM: shmobile: Remove obsolete zboot support
>
> I have queued up the above patches for v4.3.
>
> > pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> > pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> > pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> > pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>
> As the above patches are sh-pfc patches they would typically
> be steered through Linus's tree via Laurent. If they wish
> to take that path then I'm happy for this to be attached:
>
> Acked-by: Simon Horman <horms+renesas@verge.net.au>
And
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>
> Alternatively, I am happy to take the above sh-pfc patches through
> my tree but I would like to do so with an Ack from at least Linus.
I'm fine with both. I think it would be easier to applied them through your
tree if Linus is fine with that. Those patches shouldn't generate any
conflict.
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 9:05 ` Laurent Pinchart
0 siblings, 0 replies; 50+ messages in thread
From: Laurent Pinchart @ 2015-06-19 9:05 UTC (permalink / raw)
To: Simon Horman
Cc: Geert Uytterhoeven, Magnus Damm, Arnd Bergmann, linux-sh,
linux-arm-kernel, Linus Walleij, linux-gpio
Hi Simon,
On Friday 19 June 2015 12:41:00 Simon Horman wrote:
> [ CC Linus, Laurent, linux-gpio ]
>
> On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> > Hi Simon, Magnus,
> >
> > The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> > supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> > A1 (r8a7740) multi-platform kernels.
> >
> > Lacking areas are:
> > - USB (it does't work in legacy, neither),
> > - HDMI on armadillo (it doesn't work in legacy, neither),
> > - Camera on armadillo (we don't care),
> >
> > - LCDC:
> > - on armadillo, this is supported by the board staging code,
> > - on kzm9g, the LCDC is wired to the legacy INTC, which is not
> >
> > planned to be supported with DT,
> >
> > - DMAC/IPMMU (no DT bindings are planned).
> >
> > Hence this patch series removes legacy board and SoC code for
> > sh73a0/kzm9g and r8a7740/armadillo.
> >
> > It consists of 4 parts:
> > - Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
> >
> > dtb) and sh73a0,
> >
> > - Patches 5-8 remove legacy support for armadillo (board code,
> >
> > defconfig, dtb) and r8a7740,
> >
> > - Patches 9-11 remove generic shmobile support code (dma-register.h,
> >
> > legacy PM Domains, zboot) that became unused by the removal of
> > legacy sh73a0/kzm9g and r8a7740/armadillo,
> >
> > - Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
> >
> > pinctrl drivers.
> >
> > Dependencies:
> > - This is against next-20150617,
> > - To keep up with existing LCDC functionality for armadillo-legacy,
> >
> > the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
> > 0/7] staging: board: armadillo800eva: Board staging for
> > sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
> > However, it can be applied as-is now, and board staging can he
> > handled in parallel (if at all).
> >
> > Thanks for applying!
> >
> > Geert Uytterhoeven (15):
> > ARM: shmobile: Remove legacy board code for KZM-A9-GT
> > ARM: shmobile: Remove legacy kzm9g_defconfig
> > ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> > ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> > ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> > ARM: shmobile: Remove legacy armadillo800eva_defconfig
> > ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> > ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> > ARM: shmobile: Remove unused dma-register.h
> > ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> > ARM: shmobile: Remove obsolete zboot support
>
> I have queued up the above patches for v4.3.
>
> > pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> > pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> > pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> > pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>
> As the above patches are sh-pfc patches they would typically
> be steered through Linus's tree via Laurent. If they wish
> to take that path then I'm happy for this to be attached:
>
> Acked-by: Simon Horman <horms+renesas@verge.net.au>
And
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>
> Alternatively, I am happy to take the above sh-pfc patches through
> my tree but I would like to do so with an Ack from at least Linus.
I'm fine with both. I think it would be easier to applied them through your
tree if Linus is fine with that. Those patches shouldn't generate any
conflict.
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-06-19 9:05 ` Laurent Pinchart
0 siblings, 0 replies; 50+ messages in thread
From: Laurent Pinchart @ 2015-06-19 9:05 UTC (permalink / raw)
To: linux-arm-kernel
Hi Simon,
On Friday 19 June 2015 12:41:00 Simon Horman wrote:
> [ CC Linus, Laurent, linux-gpio ]
>
> On Wed, Jun 17, 2015 at 11:31:16AM +0200, Geert Uytterhoeven wrote:
> > Hi Simon, Magnus,
> >
> > The KZM-A9-GT and Armadillo-800 EVA boards are now sufficiently
> > supported by DT-based and board-less SH-Mobile AG5 (sh73a0) and R-Mobile
> > A1 (r8a7740) multi-platform kernels.
> >
> > Lacking areas are:
> > - USB (it does't work in legacy, neither),
> > - HDMI on armadillo (it doesn't work in legacy, neither),
> > - Camera on armadillo (we don't care),
> >
> > - LCDC:
> > - on armadillo, this is supported by the board staging code,
> > - on kzm9g, the LCDC is wired to the legacy INTC, which is not
> >
> > planned to be supported with DT,
> >
> > - DMAC/IPMMU (no DT bindings are planned).
> >
> > Hence this patch series removes legacy board and SoC code for
> > sh73a0/kzm9g and r8a7740/armadillo.
> >
> > It consists of 4 parts:
> > - Patches 1-4 remove legacy support for kzm9g (board code, defconfig,
> >
> > dtb) and sh73a0,
> >
> > - Patches 5-8 remove legacy support for armadillo (board code,
> >
> > defconfig, dtb) and r8a7740,
> >
> > - Patches 9-11 remove generic shmobile support code (dma-register.h,
> >
> > legacy PM Domains, zboot) that became unused by the removal of
> > legacy sh73a0/kzm9g and r8a7740/armadillo,
> >
> > - Patches 12-15 remove legacy sh73a0 and r8a7740 support in the
> >
> > pinctrl drivers.
> >
> > Dependencies:
> > - This is against next-20150617,
> > - To keep up with existing LCDC functionality for armadillo-legacy,
> >
> > the r8a7740/armadillo part (and later parts) depends on "[PATCH v2
> > 0/7] staging: board: armadillo800eva: Board staging for
> > sh_mobile_lcdc_fb" (https://lkml.org/lkml/2015/6/17/115).
> > However, it can be applied as-is now, and board staging can he
> > handled in parallel (if at all).
> >
> > Thanks for applying!
> >
> > Geert Uytterhoeven (15):
> > ARM: shmobile: Remove legacy board code for KZM-A9-GT
> > ARM: shmobile: Remove legacy kzm9g_defconfig
> > ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds
> > ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5
> > ARM: shmobile: Remove legacy board code for Armadillo-800 EVA
> > ARM: shmobile: Remove legacy armadillo800eva_defconfig
> > ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds
> > ARM: shmobile: Remove legacy SoC code for R-Mobile A1
> > ARM: shmobile: Remove unused dma-register.h
> > ARM: shmobile: R-Mobile: Remove legacy PM Domain code
> > ARM: shmobile: Remove obsolete zboot support
>
> I have queued up the above patches for v4.3.
>
> > pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
> > pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
> > pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
> > pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>
> As the above patches are sh-pfc patches they would typically
> be steered through Linus's tree via Laurent. If they wish
> to take that path then I'm happy for this to be attached:
>
> Acked-by: Simon Horman <horms+renesas@verge.net.au>
And
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>
> Alternatively, I am happy to take the above sh-pfc patches through
> my tree but I would like to do so with an Ack from at least Linus.
I'm fine with both. I think it would be easier to applied them through your
tree if Linus is fine with that. Those patches shouldn't generate any
conflict.
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
2015-06-19 7:30 ` Geert Uytterhoeven
(?)
@ 2015-07-13 10:00 ` Linus Walleij
-1 siblings, 0 replies; 50+ messages in thread
From: Linus Walleij @ 2015-07-13 10:00 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 19, 2015 at 9:30 AM, Geert Uytterhoeven
<geert@linux-m68k.org> wrote:
> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
>> [ CC Linus, Laurent, linux-gpio ]
>>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>>
>> As the above patches are sh-pfc patches they would typically
>> be steered through Linus's tree via Laurent. If they wish
>> to take that path then I'm happy for this to be attached:
>>
>> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>>
>> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>>
>> Alternatively, I am happy to take the above sh-pfc patches through
>> my tree but I would like to do so with an Ack from at least Linus.
>
> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
> patches from getting applied prematurely.
> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
> which is always pleasant.
I would prefer to take these four into the pin control tree when you
consider them finished as there is obviously more PFC stuff coming
for this next kernel cycle and I want to avoid collisions and keep
things together. Will you send them to me separately?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-07-13 10:00 ` Linus Walleij
0 siblings, 0 replies; 50+ messages in thread
From: Linus Walleij @ 2015-07-13 10:00 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Simon Horman, Geert Uytterhoeven, Magnus Damm, Arnd Bergmann,
Linux-sh list, linux-arm-kernel, Laurent Pinchart, linux-gpio
On Fri, Jun 19, 2015 at 9:30 AM, Geert Uytterhoeven
<geert@linux-m68k.org> wrote:
> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
>> [ CC Linus, Laurent, linux-gpio ]
>>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>>
>> As the above patches are sh-pfc patches they would typically
>> be steered through Linus's tree via Laurent. If they wish
>> to take that path then I'm happy for this to be attached:
>>
>> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>>
>> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>>
>> Alternatively, I am happy to take the above sh-pfc patches through
>> my tree but I would like to do so with an Ack from at least Linus.
>
> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
> patches from getting applied prematurely.
> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
> which is always pleasant.
I would prefer to take these four into the pin control tree when you
consider them finished as there is obviously more PFC stuff coming
for this next kernel cycle and I want to avoid collisions and keep
things together. Will you send them to me separately?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-07-13 10:00 ` Linus Walleij
0 siblings, 0 replies; 50+ messages in thread
From: Linus Walleij @ 2015-07-13 10:00 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 19, 2015 at 9:30 AM, Geert Uytterhoeven
<geert@linux-m68k.org> wrote:
> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
>> [ CC Linus, Laurent, linux-gpio ]
>>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>>
>> As the above patches are sh-pfc patches they would typically
>> be steered through Linus's tree via Laurent. If they wish
>> to take that path then I'm happy for this to be attached:
>>
>> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>>
>> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>>
>> Alternatively, I am happy to take the above sh-pfc patches through
>> my tree but I would like to do so with an Ack from at least Linus.
>
> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
> patches from getting applied prematurely.
> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
> which is always pleasant.
I would prefer to take these four into the pin control tree when you
consider them finished as there is obviously more PFC stuff coming
for this next kernel cycle and I want to avoid collisions and keep
things together. Will you send them to me separately?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
2015-07-13 10:00 ` Linus Walleij
(?)
@ 2015-07-13 10:06 ` Geert Uytterhoeven
-1 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-07-13 10:06 UTC (permalink / raw)
To: linux-arm-kernel
Hi Linus,
On Mon, Jul 13, 2015 at 12:00 PM, Linus Walleij
<linus.walleij@linaro.org> wrote:
> On Fri, Jun 19, 2015 at 9:30 AM, Geert Uytterhoeven
> <geert@linux-m68k.org> wrote:
>> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
>>> [ CC Linus, Laurent, linux-gpio ]
>
>>>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>>>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>>>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>>>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>>>
>>> As the above patches are sh-pfc patches they would typically
>>> be steered through Linus's tree via Laurent. If they wish
>>> to take that path then I'm happy for this to be attached:
>>>
>>> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>>>
>>> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>>>
>>> Alternatively, I am happy to take the above sh-pfc patches through
>>> my tree but I would like to do so with an Ack from at least Linus.
>>
>> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
>> patches from getting applied prematurely.
>> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
>> which is always pleasant.
>
> I would prefer to take these four into the pin control tree when you
> consider them finished as there is obviously more PFC stuff coming
> for this next kernel cycle and I want to avoid collisions and keep
> things together. Will you send them to me separately?
OK, I will send them your way.
I think at this point we're quite sure the sh73a0/r8a7740 removal will hit v4.3.
This does mean sh73a0/r8a7740-legacy will be broken in pinctrl/for-next,
but we don't care, as the support is gone in -next anyway.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-07-13 10:06 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-07-13 10:06 UTC (permalink / raw)
To: Linus Walleij
Cc: Simon Horman, Geert Uytterhoeven, Magnus Damm, Arnd Bergmann,
Linux-sh list, linux-arm-kernel, Laurent Pinchart, linux-gpio
Hi Linus,
On Mon, Jul 13, 2015 at 12:00 PM, Linus Walleij
<linus.walleij@linaro.org> wrote:
> On Fri, Jun 19, 2015 at 9:30 AM, Geert Uytterhoeven
> <geert@linux-m68k.org> wrote:
>> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
>>> [ CC Linus, Laurent, linux-gpio ]
>
>>>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>>>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>>>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>>>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>>>
>>> As the above patches are sh-pfc patches they would typically
>>> be steered through Linus's tree via Laurent. If they wish
>>> to take that path then I'm happy for this to be attached:
>>>
>>> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>>>
>>> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>>>
>>> Alternatively, I am happy to take the above sh-pfc patches through
>>> my tree but I would like to do so with an Ack from at least Linus.
>>
>> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
>> patches from getting applied prematurely.
>> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
>> which is always pleasant.
>
> I would prefer to take these four into the pin control tree when you
> consider them finished as there is obviously more PFC stuff coming
> for this next kernel cycle and I want to avoid collisions and keep
> things together. Will you send them to me separately?
OK, I will send them your way.
I think at this point we're quite sure the sh73a0/r8a7740 removal will hit v4.3.
This does mean sh73a0/r8a7740-legacy will be broken in pinctrl/for-next,
but we don't care, as the support is gone in -next anyway.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo
@ 2015-07-13 10:06 ` Geert Uytterhoeven
0 siblings, 0 replies; 50+ messages in thread
From: Geert Uytterhoeven @ 2015-07-13 10:06 UTC (permalink / raw)
To: linux-arm-kernel
Hi Linus,
On Mon, Jul 13, 2015 at 12:00 PM, Linus Walleij
<linus.walleij@linaro.org> wrote:
> On Fri, Jun 19, 2015 at 9:30 AM, Geert Uytterhoeven
> <geert@linux-m68k.org> wrote:
>> On Fri, Jun 19, 2015 at 5:41 AM, Simon Horman <horms@verge.net.au> wrote:
>>> [ CC Linus, Laurent, linux-gpio ]
>
>>>> pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check
>>>> pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry
>>>> pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check
>>>> pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry
>>>
>>> As the above patches are sh-pfc patches they would typically
>>> be steered through Linus's tree via Laurent. If they wish
>>> to take that path then I'm happy for this to be attached:
>>>
>>> Acked-by: Simon Horman <horms+renesas@verge.net.au>
>>>
>>> FWIW the above path is the one that the removal of mackerel/sh7372 took.
>>>
>>> Alternatively, I am happy to take the above sh-pfc patches through
>>> my tree but I would like to do so with an Ack from at least Linus.
>>
>> I didn't CC Linus and linux-gpio at this stage yet, to prevent the pfc
>> patches from getting applied prematurely.
>> But things have gone more smoothly (esp. w.r.t. board staging) than expected,
>> which is always pleasant.
>
> I would prefer to take these four into the pin control tree when you
> consider them finished as there is obviously more PFC stuff coming
> for this next kernel cycle and I want to avoid collisions and keep
> things together. Will you send them to me separately?
OK, I will send them your way.
I think at this point we're quite sure the sh73a0/r8a7740 removal will hit v4.3.
This does mean sh73a0/r8a7740-legacy will be broken in pinctrl/for-next,
but we don't care, as the support is gone in -next anyway.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 50+ messages in thread
end of thread, other threads:[~2015-07-13 10:06 UTC | newest]
Thread overview: 50+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-06-17 9:31 [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 01/15] ARM: shmobile: Remove legacy board code for KZM-A9-GT Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 02/15] ARM: shmobile: Remove legacy kzm9g_defconfig Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 03/15] ARM: shmobile: Drop sh73a0-kzm9g.dtb for legacy builds Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 04/15] ARM: shmobile: Remove legacy SoC code for SH-Mobile AG5 Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 05/15] ARM: shmobile: Remove legacy board code for Armadillo-800 EVA Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 06/15] ARM: shmobile: Remove legacy armadillo800eva_defconfig Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 07/15] ARM: shmobile: Drop r8a7740-armadillo800eva.dtb for legacy builds Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 08/15] ARM: shmobile: Remove legacy SoC code for R-Mobile A1 Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 09/15] ARM: shmobile: Remove unused dma-register.h Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 10/15] ARM: shmobile: R-Mobile: Remove legacy PM Domain code Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 11/15] ARM: shmobile: Remove obsolete zboot support Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 12/15] pinctrl: sh-pfc: sh73a0: Remove obsolete multi-platform check Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 13/15] pinctrl: sh-pfc: Remove obsolete sh73a0 platform_device_id entry Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 14/15] pinctrl: sh-pfc: r8a7740: Remove obsolete multi-platform check Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-17 9:31 ` [PATCH 15/15] pinctrl: sh-pfc: Remove obsolete r8a7740 platform_device_id entry Geert Uytterhoeven
2015-06-17 9:31 ` Geert Uytterhoeven
2015-06-19 3:41 ` [PATCH 00/15] ARM: shmobile: Remove legacy sh73a0/kzm9g and r8a7740/armadillo Simon Horman
2015-06-19 3:41 ` Simon Horman
2015-06-19 3:41 ` Simon Horman
2015-06-19 7:30 ` Geert Uytterhoeven
2015-06-19 7:30 ` Geert Uytterhoeven
2015-06-19 7:30 ` Geert Uytterhoeven
2015-06-19 8:17 ` Simon Horman
2015-06-19 8:17 ` Simon Horman
2015-06-19 8:17 ` Simon Horman
2015-07-13 10:00 ` Linus Walleij
2015-07-13 10:00 ` Linus Walleij
2015-07-13 10:00 ` Linus Walleij
2015-07-13 10:06 ` Geert Uytterhoeven
2015-07-13 10:06 ` Geert Uytterhoeven
2015-07-13 10:06 ` Geert Uytterhoeven
2015-06-19 9:05 ` Laurent Pinchart
2015-06-19 9:05 ` Laurent Pinchart
2015-06-19 9:05 ` Laurent Pinchart
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.