[PATCH 00/20] mpt3sas: driver update

[PATCH 00/20] mpt3sas: driver update

[Sreekanth Reddy]

This patch set contains all the features and defect fixes from Phase4 to Phase8.

Except below patch, all other patches have Reviewed-by signature from either
Martin K. Petersen, Johannes Thumshirn, Tomas Henzl and Joe Lawrence. Thanks for
reviewing these patches.
[PATCH v2 16/20] [SCSI] mpt3sas: Added support for customer specific branding

I am posting this patch set once again by promoting all the patches to v2,
so that it will be easy to pick up this patch set for next kernel release.

Thanks,
Sreekanth

Sreekanth Reddy (20):
  [SCSI] mpt3sas: Added Combined Reply Queue feature to extend
    up-to 96 MSIX vector support
  [SCSI] mpt3sas: Get IOC_FACTS information using  handshake
    protocol only after HBA card gets into READY or Operational
    state.
  [SCSI] mpt3sas: Don't block the drive when drive addition under
    the control of SML
  [SCSI] mpt3sas: Remove redundancy code while freeing the
    controller resources.
  [SCSI] mpt3sas: MPI 2.5 Rev I (2.5.4) specifications.
  [SCSI] mpt3sas: Provides the physical location of sas  drives
  [SCSI] mpt3sas: Bump mpt3sas Driver version to v5.100.00.00
  [SCSI] mpt3sas: Update MPI2 strings to MPI2.5
  [SCSI] mpt3sas: MPI 2.5 Rev J (2.5.5) specification and  2.00.34
    header files
  [SCSI] mpt3sas: Add branding string support for OEM's HBA
  [SCSI] mpt3sas: Add branding string support for OEM custom HBA
  [SCSI] mpt3sas: Bump mpt3sas driver version to v6.100.00.00
  [SCSI] mpt3sas: MPI 2.5 Rev K (2.5.6) specifications
  [SCSI] mpt3sas: Complete the SCSI command with DID_RESET status
    for log_info value 0x0x32010081
  [SCSI] mpt3sas: Return host busy error status to SML when DMA
    mapping of scatter gather list fails for a SCSI command
  [SCSI] mpt3sas: Added support for customer specific branding
  [SCSI] mpt3sas: Use alloc_ordered_workqueue() API instead of
    create_singlethread_workqueue() API
  [SCSI] mpt3sas: Call dma_mapping_error() API after  mapping an
    address with dma_map_single() API
  [SCSI] mpt3sas: When device is blocked followed by unblock fails,
    unfreeze the I/Os
  [SCSI] mpt3sas : Bump mpt3sas driver version to 9.100.00.00

 drivers/scsi/mpt3sas/mpi/mpi2.h          |   8 +-
 drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h     |  52 ++++-
 drivers/scsi/mpt3sas/mpi/mpi2_ioc.h      |   4 +-
 drivers/scsi/mpt3sas/mpi/mpi2_tool.h     |   4 +-
 drivers/scsi/mpt3sas/mpt3sas_base.c      | 310 +++++++++++++++++++++++++---
 drivers/scsi/mpt3sas/mpt3sas_base.h      |  57 ++++-
 drivers/scsi/mpt3sas/mpt3sas_scsih.c     | 343 ++++++++++++++++++++++++++-----
 drivers/scsi/mpt3sas/mpt3sas_transport.c |  22 +-
 8 files changed, 694 insertions(+), 106 deletions(-)

-- 
2.0.2

[PATCH v2 01/20] [SCSI] mpt3sas: Added Combined Reply Queue feature to extend up-to 96 MSIX vector support

[Sreekanth Reddy]

In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to up-to 96.

Following are changes that are done in this patch
1. This feature is enabled only for SAS3 C0 and higher revision cards and also only when reply post free queue count is greater than 8.
2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces are used. MSI-X index numbered from 0 to 7 use the first SupplementalReplyPostHostIndex system interface to update its corresponding ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the second SupplementalReplyPostHostIndex system interface and so on. These 12 SuppementalReplyPostHostIndex system interfaces address are saved in the array replyPostRegisterIndex[].
3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X vectors. So MSIxIndex field in these register must contain a value between 0 and 7.
4. After processing the reply descriptors from a reply post free queues then update the new reply post host index value in ReplyPostHostIndex field and (msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex register. The Address of this SupplementalReplyPostHostIndex register is retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.

Changes in v1:
 Updated the description of module parameter max_msix_vectors

Changes in v2:
 * Defined some Combined Reply Queue's feature magic values,
 * Removed unnecessory brackets,
 * Added comments where ever required.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 93 +++++++++++++++++++++++++++++++++----
 drivers/scsi/mpt3sas/mpt3sas_base.h | 14 +++++-
 2 files changed, 98 insertions(+), 9 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 14a781b..63a8588 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -83,10 +83,10 @@ static int msix_disable = -1;
 module_param(msix_disable, int, 0);
 MODULE_PARM_DESC(msix_disable, " disable msix routed interrupts (default=0)");
 
-static int max_msix_vectors = 8;
+static int max_msix_vectors = -1;
 module_param(max_msix_vectors, int, 0);
 MODULE_PARM_DESC(max_msix_vectors,
-	" max msix vectors - (default=8)");
+	" max msix vectors");
 
 static int mpt3sas_fwfault_debug;
 MODULE_PARM_DESC(mpt3sas_fwfault_debug,
@@ -1009,8 +1009,30 @@ _base_interrupt(int irq, void *bus_id)
 	}
 
 	wmb();
-	writel(reply_q->reply_post_host_index | (msix_index <<
-	    MPI2_RPHI_MSIX_INDEX_SHIFT), &ioc->chip->ReplyPostHostIndex);
+
+	/* Update Reply Post Host Index.
+	 * For those HBA's which support combined reply queue feature
+	 * 1. Get the correct Supplemental Reply Post Host Index Register.
+	 *    i.e. (msix_index / 8)th entry from Supplemental Reply Post Host
+	 *    Index Register address bank i.e replyPostRegisterIndex[],
+	 * 2. Then update this register with new reply host index value
+	 *    in ReplyPostIndex field and the MSIxIndex field with
+	 *    msix_index value reduced to a value between 0 and 7,
+	 *    using a modulo 8 operation. Since each Supplemental Reply Post
+	 *    Host Index Register supports 8 MSI-X vectors.
+	 *
+	 * For other HBA's just update the Reply Post Host Index register with
+	 * new reply host index value in ReplyPostIndex Field and msix_index
+	 * value in MSIxIndex field.
+	 */
+	if (ioc->msix96_vector)
+		writel(reply_q->reply_post_host_index | ((msix_index  & 7) <<
+			MPI2_RPHI_MSIX_INDEX_SHIFT),
+			ioc->replyPostRegisterIndex[msix_index/8]);
+	else
+		writel(reply_q->reply_post_host_index | (msix_index <<
+			MPI2_RPHI_MSIX_INDEX_SHIFT),
+			&ioc->chip->ReplyPostHostIndex);
 	atomic_dec(&reply_q->busy);
 	return IRQ_HANDLED;
 }
@@ -1560,8 +1582,6 @@ _base_check_enable_msix(struct MPT3SAS_ADAPTER *ioc)
 
 	pci_read_config_word(ioc->pdev, base + 2, &message_control);
 	ioc->msix_vector_count = (message_control & 0x3FF) + 1;
-	if (ioc->msix_vector_count > 8)
-		ioc->msix_vector_count = 8;
 	dinitprintk(ioc, pr_info(MPT3SAS_FMT
 		"msix is supported, vector_count(%d)\n",
 		ioc->name, ioc->msix_vector_count));
@@ -1880,6 +1900,36 @@ mpt3sas_base_map_resources(struct MPT3SAS_ADAPTER *ioc)
 	if (r)
 		goto out_fail;
 
+	/* Use the Combined reply queue feature only for SAS3 C0 & higher
+	 * revision HBAs and also only when reply queue count is greater than 8
+	 */
+	if (ioc->msix96_vector && ioc->reply_queue_count > 8) {
+		/* Determine the Supplemental Reply Post Host Index Registers
+		 * Addresse. Supplemental Reply Post Host Index Registers
+		 * starts at offset MPI25_SUP_REPLY_POST_HOST_INDEX_OFFSET and
+		 * each register is at offset bytes of
+		 * MPT3_SUP_REPLY_POST_HOST_INDEX_REG_OFFSET from previous one.
+		 */
+		ioc->replyPostRegisterIndex = kcalloc(
+		     MPT3_SUP_REPLY_POST_HOST_INDEX_REG_COUNT,
+		     sizeof(resource_size_t *), GFP_KERNEL);
+		if (!ioc->replyPostRegisterIndex) {
+			dfailprintk(ioc, printk(MPT3SAS_FMT
+			"allocation for reply Post Register Index failed!!!\n",
+								   ioc->name));
+			r = -ENOMEM;
+			goto out_fail;
+		}
+
+		for (i = 0; i < MPT3_SUP_REPLY_POST_HOST_INDEX_REG_COUNT; i++) {
+			ioc->replyPostRegisterIndex[i] = (resource_size_t *)
+			     ((u8 *)&ioc->chip->Doorbell +
+			     MPI25_SUP_REPLY_POST_HOST_INDEX_OFFSET +
+			     (i * MPT3_SUP_REPLY_POST_HOST_INDEX_REG_OFFSET));
+		}
+	} else
+		ioc->msix96_vector = 0;
+
 	list_for_each_entry(reply_q, &ioc->reply_queue_list, list)
 		pr_info(MPT3SAS_FMT "%s: IRQ %d\n",
 		    reply_q->name,  ((ioc->msix_enable) ? "PCI-MSI-X enabled" :
@@ -1901,6 +1951,8 @@ mpt3sas_base_map_resources(struct MPT3SAS_ADAPTER *ioc)
 	pci_release_selected_regions(ioc->pdev, ioc->bars);
 	pci_disable_pcie_error_reporting(pdev);
 	pci_disable_device(pdev);
+	if (ioc->msix96_vector)
+		kfree(ioc->replyPostRegisterIndex);
 	return r;
 }
 
@@ -4522,8 +4574,15 @@ _base_make_ioc_operational(struct MPT3SAS_ADAPTER *ioc, int sleep_flag)
 
 	/* initialize reply post host index */
 	list_for_each_entry(reply_q, &ioc->reply_queue_list, list) {
-		writel(reply_q->msix_index << MPI2_RPHI_MSIX_INDEX_SHIFT,
-		    &ioc->chip->ReplyPostHostIndex);
+		if (ioc->msix96_vector)
+			writel((reply_q->msix_index & 7)<<
+			   MPI2_RPHI_MSIX_INDEX_SHIFT,
+			   ioc->replyPostRegisterIndex[reply_q->msix_index/8]);
+		else
+			writel(reply_q->msix_index <<
+				MPI2_RPHI_MSIX_INDEX_SHIFT,
+				&ioc->chip->ReplyPostHostIndex);
+
 		if (!_base_is_controller_msix_enabled(ioc))
 			goto skip_init_reply_post_host_index;
 	}
@@ -4577,6 +4636,9 @@ mpt3sas_base_free_resources(struct MPT3SAS_ADAPTER *ioc)
 	_base_free_irq(ioc);
 	_base_disable_msix(ioc);
 
+	if (ioc->msix96_vector)
+		kfree(ioc->replyPostRegisterIndex);
+
 	if (ioc->chip_phys && ioc->chip)
 		iounmap(ioc->chip);
 	ioc->chip_phys = 0;
@@ -4600,6 +4662,7 @@ mpt3sas_base_attach(struct MPT3SAS_ADAPTER *ioc)
 {
 	int r, i;
 	int cpu_id, last_cpu_id = 0;
+	u8 revision;
 
 	dinitprintk(ioc, pr_info(MPT3SAS_FMT "%s\n", ioc->name,
 	    __func__));
@@ -4619,6 +4682,20 @@ mpt3sas_base_attach(struct MPT3SAS_ADAPTER *ioc)
 		goto out_free_resources;
 	}
 
+	/* Check whether the controller revision is C0 or above.
+	 * only C0 and above revision controllers support 96 MSI-X vectors.
+	 */
+	revision = ioc->pdev->revision;
+
+	if ((ioc->pdev->device == MPI25_MFGPAGE_DEVID_SAS3004 ||
+	     ioc->pdev->device == MPI25_MFGPAGE_DEVID_SAS3008 ||
+	     ioc->pdev->device == MPI25_MFGPAGE_DEVID_SAS3108_1 ||
+	     ioc->pdev->device == MPI25_MFGPAGE_DEVID_SAS3108_2 ||
+	     ioc->pdev->device == MPI25_MFGPAGE_DEVID_SAS3108_5 ||
+	     ioc->pdev->device == MPI25_MFGPAGE_DEVID_SAS3108_6) &&
+	     (revision >= 0x02))
+		ioc->msix96_vector = 1;
+
 	ioc->rdpq_array_enable_assigned = 0;
 	ioc->dma_mask = 0;
 	r = mpt3sas_base_map_resources(ioc);
diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index afa8816..a7386ee 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -158,6 +158,13 @@
 #define MPT3_DIAG_BUFFER_IS_RELEASED	(0x02)
 #define MPT3_DIAG_BUFFER_IS_DIAG_RESET	(0x04)
 
+/*
+ * Combined Reply Queue constants,
+ * There are twelve Supplemental Reply Post Host Index Registers
+ * and each register is at offset 0x10 bytes from the previous one.
+ */
+#define MPT3_SUP_REPLY_POST_HOST_INDEX_REG_COUNT 12
+#define MPT3_SUP_REPLY_POST_HOST_INDEX_REG_OFFSET (0x10)
 
 /* OEM Identifiers */
 #define MFG10_OEM_ID_INVALID                   (0x00000000)
@@ -728,7 +735,8 @@ typedef void (*MPT3SAS_FLUSH_RUNNING_CMDS)(struct MPT3SAS_ADAPTER *ioc);
  *				is assigned only ones
  * @reply_queue_count: number of reply queue's
  * @reply_queue_list: link list contaning the reply queue info
- * @reply_post_host_index: head index in the pool where FW completes IO
+ * @msix96_vector: 96 MSI-X vector support
+ * @replyPostRegisterIndex: index of next position in Reply Desc Post Queue
  * @delayed_tr_list: target reset link list
  * @delayed_tr_volume_list: volume target reset link list
  * @@temp_sensors_count: flag to carry the number of temperature sensors
@@ -937,6 +945,10 @@ struct MPT3SAS_ADAPTER {
 	u8		reply_queue_count;
 	struct list_head reply_queue_list;
 
+	u8		msix96_vector;
+	/* reply post register index */
+	resource_size_t	**replyPostRegisterIndex;
+
 	struct list_head delayed_tr_list;
 	struct list_head delayed_tr_volume_list;
 	u8		temp_sensors_count;
-- 
2.0.2

[PATCH v2 02/20] [SCSI] mpt3sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state.

[Sreekanth Reddy]

Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state.

This patch will make sure that
 1.Driver to send IOC facts request message only if HBA is in operational or ready state.
 2.If IOC is in fault state, a diagnostic reset would be issued.
 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state.
   If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver.

Changes in v1:
   If PCI Recovery is on then return with -EFAULT in the function _base_wait_for_iocstate().

Changes in v2:
   Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 68 +++++++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 63a8588..0410cc5 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -3189,6 +3189,9 @@ _base_wait_on_iocstate(struct MPT3SAS_ADAPTER *ioc, u32 ioc_state, int timeout,
  * Notes: MPI2_HIS_IOC2SYS_DB_STATUS - set to one when IOC writes to doorbell.
  */
 static int
+_base_diag_reset(struct MPT3SAS_ADAPTER *ioc, int sleep_flag);
+
+static int
 _base_wait_for_doorbell_int(struct MPT3SAS_ADAPTER *ioc, int timeout,
 	int sleep_flag)
 {
@@ -3731,6 +3734,64 @@ _base_get_port_facts(struct MPT3SAS_ADAPTER *ioc, int port, int sleep_flag)
 }
 
 /**
+ * _base_wait_for_iocstate - Wait until the card is in READY or OPERATIONAL
+ * @ioc: per adapter object
+ * @timeout:
+ * @sleep_flag: CAN_SLEEP or NO_SLEEP
+ *
+ * Returns 0 for success, non-zero for failure.
+ */
+static int
+_base_wait_for_iocstate(struct MPT3SAS_ADAPTER *ioc, int timeout,
+	int sleep_flag)
+{
+	u32 ioc_state;
+	int rc;
+
+	dinitprintk(ioc, printk(MPT3SAS_FMT "%s\n", ioc->name,
+	    __func__));
+
+	if (ioc->pci_error_recovery) {
+		dfailprintk(ioc, printk(MPT3SAS_FMT
+		    "%s: host in pci error recovery\n", ioc->name, __func__));
+		return -EFAULT;
+	}
+
+	ioc_state = mpt3sas_base_get_iocstate(ioc, 0);
+	dhsprintk(ioc, printk(MPT3SAS_FMT "%s: ioc_state(0x%08x)\n",
+	    ioc->name, __func__, ioc_state));
+
+	if (((ioc_state & MPI2_IOC_STATE_MASK) == MPI2_IOC_STATE_READY) ||
+	    (ioc_state & MPI2_IOC_STATE_MASK) == MPI2_IOC_STATE_OPERATIONAL)
+		return 0;
+
+	if (ioc_state & MPI2_DOORBELL_USED) {
+		dhsprintk(ioc, printk(MPT3SAS_FMT
+		    "unexpected doorbell active!\n", ioc->name));
+		goto issue_diag_reset;
+	}
+
+	if ((ioc_state & MPI2_IOC_STATE_MASK) == MPI2_IOC_STATE_FAULT) {
+		mpt3sas_base_fault_info(ioc, ioc_state &
+		    MPI2_DOORBELL_DATA_MASK);
+		goto issue_diag_reset;
+	}
+
+	ioc_state = _base_wait_on_iocstate(ioc, MPI2_IOC_STATE_READY,
+	    timeout, sleep_flag);
+	if (ioc_state) {
+		dfailprintk(ioc, printk(MPT3SAS_FMT
+		    "%s: failed going to ready state (ioc_state=0x%x)\n",
+		    ioc->name, __func__, ioc_state));
+		return -EFAULT;
+	}
+
+ issue_diag_reset:
+	rc = _base_diag_reset(ioc, sleep_flag);
+	return rc;
+}
+
+/**
  * _base_get_ioc_facts - obtain ioc facts reply and save in ioc
  * @ioc: per adapter object
  * @sleep_flag: CAN_SLEEP or NO_SLEEP
@@ -3748,6 +3809,13 @@ _base_get_ioc_facts(struct MPT3SAS_ADAPTER *ioc, int sleep_flag)
 	dinitprintk(ioc, pr_info(MPT3SAS_FMT "%s\n", ioc->name,
 	    __func__));
 
+	r = _base_wait_for_iocstate(ioc, 10, sleep_flag);
+	if (r) {
+		dfailprintk(ioc, printk(MPT3SAS_FMT
+		    "%s: failed getting to correct state\n",
+		    ioc->name, __func__));
+		return r;
+	}
 	mpi_reply_sz = sizeof(Mpi2IOCFactsReply_t);
 	mpi_request_sz = sizeof(Mpi2IOCFactsRequest_t);
 	memset(&mpi_request, 0, mpi_request_sz);
-- 
2.0.2

[PATCH v2 03/20] [SCSI] mpt3sas: Don't block the drive when drive addition under the control of SML

[Sreekanth Reddy]

During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.

This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.

Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h      |  4 +++-
 drivers/scsi/mpt3sas/mpt3sas_scsih.c     |  7 +++++++
 drivers/scsi/mpt3sas/mpt3sas_transport.c | 18 ++++++++++++++++++
 3 files changed, 28 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index a7386ee..01d92db 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -301,7 +301,8 @@ struct _internal_cmd {
  * @responding: used in _scsih_sas_device_mark_responding
  * @fast_path: fast path feature enable bit
  * @pfa_led_on: flag for PFA LED status
- *
+ * @pend_sas_rphy_add: flag to check if device is in sas_rphy_add()
+ *	addition routine.
  */
 struct _sas_device {
 	struct list_head list;
@@ -322,6 +323,7 @@ struct _sas_device {
 	u8	responding;
 	u8	fast_path;
 	u8	pfa_led_on;
+	u8	pend_sas_rphy_add;
 };
 
 /**
diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index 5a97e32..d457dba 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -2644,6 +2644,11 @@ _scsih_block_io_device(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 {
 	struct MPT3SAS_DEVICE *sas_device_priv_data;
 	struct scsi_device *sdev;
+	struct _sas_device *sas_device;
+
+	sas_device = _scsih_sas_device_find_by_handle(ioc, handle);
+	if (!sas_device)
+		return;
 
 	shost_for_each_device(sdev, ioc->shost) {
 		sas_device_priv_data = sdev->hostdata;
@@ -2653,6 +2658,8 @@ _scsih_block_io_device(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 			continue;
 		if (sas_device_priv_data->block)
 			continue;
+		if (sas_device->pend_sas_rphy_add)
+			continue;
 		sas_device_priv_data->block = 1;
 		scsi_internal_device_block(sdev);
 		sdev_printk(KERN_INFO, sdev,
diff --git a/drivers/scsi/mpt3sas/mpt3sas_transport.c b/drivers/scsi/mpt3sas/mpt3sas_transport.c
index efb98af..7a7aa68 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_transport.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_transport.c
@@ -649,6 +649,7 @@ mpt3sas_transport_port_add(struct MPT3SAS_ADAPTER *ioc, u16 handle,
 	unsigned long flags;
 	struct _sas_node *sas_node;
 	struct sas_rphy *rphy;
+	struct _sas_device *sas_device = NULL;
 	int i;
 	struct sas_port *port;
 
@@ -731,10 +732,27 @@ mpt3sas_transport_port_add(struct MPT3SAS_ADAPTER *ioc, u16 handle,
 		    mpt3sas_port->remote_identify.device_type);
 
 	rphy->identify = mpt3sas_port->remote_identify;
+
+	if (mpt3sas_port->remote_identify.device_type == SAS_END_DEVICE) {
+		sas_device = mpt3sas_scsih_sas_device_find_by_sas_address(ioc,
+				    mpt3sas_port->remote_identify.sas_address);
+		if (!sas_device) {
+			dfailprintk(ioc, printk(MPT3SAS_FMT
+				"failure at %s:%d/%s()!\n",
+				ioc->name, __FILE__, __LINE__, __func__));
+			goto out_fail;
+		}
+		sas_device->pend_sas_rphy_add = 1;
+	}
+
 	if ((sas_rphy_add(rphy))) {
 		pr_err(MPT3SAS_FMT "failure at %s:%d/%s()!\n",
 		    ioc->name, __FILE__, __LINE__, __func__);
 	}
+
+	if (mpt3sas_port->remote_identify.device_type == SAS_END_DEVICE)
+		sas_device->pend_sas_rphy_add = 0;
+
 	if ((ioc->logging_level & MPT_DEBUG_TRANSPORT))
 		dev_printk(KERN_INFO, &rphy->dev,
 			"add: handle(0x%04x), sas_addr(0x%016llx)\n",
-- 
2.0.2

[PATCH v2 04/20] [SCSI] mpt3sas: Remove redundancy code while freeing the controller resources.

[Sreekanth Reddy]

Removed the redundancy code while freeing the controller resources.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 57 +++++++++++++++++++++----------------
 1 file changed, 32 insertions(+), 25 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 0410cc5..bf2d7dc 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -1813,6 +1813,36 @@ _base_enable_msix(struct MPT3SAS_ADAPTER *ioc)
 }
 
 /**
+ * mpt3sas_base_unmap_resources - free controller resources
+ * @ioc: per adapter object
+ */
+void
+mpt3sas_base_unmap_resources(struct MPT3SAS_ADAPTER *ioc)
+{
+	struct pci_dev *pdev = ioc->pdev;
+
+	dexitprintk(ioc, printk(MPT3SAS_FMT "%s\n",
+		ioc->name, __func__));
+
+	_base_free_irq(ioc);
+	_base_disable_msix(ioc);
+
+	if (ioc->msix96_vector)
+		kfree(ioc->replyPostRegisterIndex);
+
+	if (ioc->chip_phys) {
+		iounmap(ioc->chip);
+		ioc->chip_phys = 0;
+	}
+
+	if (pci_is_enabled(pdev)) {
+		pci_release_selected_regions(ioc->pdev, ioc->bars);
+		pci_disable_pcie_error_reporting(pdev);
+		pci_disable_device(pdev);
+	}
+}
+
+/**
  * mpt3sas_base_map_resources - map in controller resources (io/irq/memap)
  * @ioc: per adapter object
  *
@@ -1945,14 +1975,7 @@ mpt3sas_base_map_resources(struct MPT3SAS_ADAPTER *ioc)
 	return 0;
 
  out_fail:
-	if (ioc->chip_phys)
-		iounmap(ioc->chip);
-	ioc->chip_phys = 0;
-	pci_release_selected_regions(ioc->pdev, ioc->bars);
-	pci_disable_pcie_error_reporting(pdev);
-	pci_disable_device(pdev);
-	if (ioc->msix96_vector)
-		kfree(ioc->replyPostRegisterIndex);
+	mpt3sas_base_unmap_resources(ioc);
 	return r;
 }
 
@@ -4689,8 +4712,6 @@ _base_make_ioc_operational(struct MPT3SAS_ADAPTER *ioc, int sleep_flag)
 void
 mpt3sas_base_free_resources(struct MPT3SAS_ADAPTER *ioc)
 {
-	struct pci_dev *pdev = ioc->pdev;
-
 	dexitprintk(ioc, pr_info(MPT3SAS_FMT "%s\n", ioc->name,
 	    __func__));
 
@@ -4701,21 +4722,7 @@ mpt3sas_base_free_resources(struct MPT3SAS_ADAPTER *ioc)
 		ioc->shost_recovery = 0;
 	}
 
-	_base_free_irq(ioc);
-	_base_disable_msix(ioc);
-
-	if (ioc->msix96_vector)
-		kfree(ioc->replyPostRegisterIndex);
-
-	if (ioc->chip_phys && ioc->chip)
-		iounmap(ioc->chip);
-	ioc->chip_phys = 0;
-
-	if (pci_is_enabled(pdev)) {
-		pci_release_selected_regions(ioc->pdev, ioc->bars);
-		pci_disable_pcie_error_reporting(pdev);
-		pci_disable_device(pdev);
-	}
+	mpt3sas_base_unmap_resources(ioc);
 	return;
 }
 
-- 
2.0.2

[PATCH v2 05/20] [SCSI] mpt3sas: MPI 2.5 Rev I (2.5.4) specifications.

[Sreekanth Reddy]

Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header files

Below is the change set from the MPI specification for I Rev

1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7.
2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit Page 1.
3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also, added EnclosureLevel and ConnectorName Valid bit to the Flags field.
4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added EnclosureLevel Valid bit to the Flags field.
5) Added value for BIOS image to HashImageType.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpi/mpi2.h      |  6 ++++--
 drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h | 27 +++++++++++++++++++++------
 drivers/scsi/mpt3sas/mpi/mpi2_ioc.h  |  4 +++-
 3 files changed, 28 insertions(+), 9 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpi/mpi2.h b/drivers/scsi/mpt3sas/mpi/mpi2.h
index c34c115..d730c5c 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2.h
@@ -8,7 +8,7 @@
  *                 scatter/gather formats.
  * Creation Date:  June 21, 2006
  *
- * mpi2.h Version:  02.00.31
+ * mpi2.h Version:  02.00.33
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -88,6 +88,8 @@
  *                     Added MPI25_SUP_REPLY_POST_HOST_INDEX_OFFSET.
  * 04-09-13  02.00.30  Bumped MPI2_HEADER_VERSION_UNIT.
  * 04-17-13  02.00.31  Bumped MPI2_HEADER_VERSION_UNIT.
+ * 08-19-13  02.00.32  Bumped MPI2_HEADER_VERSION_UNIT.
+ * 12-05-13  02.00.33  Bumped MPI2_HEADER_VERSION_UNIT.
  * --------------------------------------------------------------------------
  */
 
@@ -121,7 +123,7 @@
 #define MPI2_VERSION_02_05                  (0x0205)
 
 /*Unit and Dev versioning for this MPI header set */
-#define MPI2_HEADER_VERSION_UNIT            (0x1F)
+#define MPI2_HEADER_VERSION_UNIT            (0x21)
 #define MPI2_HEADER_VERSION_DEV             (0x00)
 #define MPI2_HEADER_VERSION_UNIT_MASK       (0xFF00)
 #define MPI2_HEADER_VERSION_UNIT_SHIFT      (8)
diff --git a/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h b/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
index e261a31..62dfbf6 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
@@ -6,7 +6,7 @@
  *         Title:  MPI Configuration messages and pages
  * Creation Date:  November 10, 2006
  *
- *   mpi2_cnfg.h Version:  02.00.26
+ *   mpi2_cnfg.h Version:  02.00.27
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -165,6 +165,16 @@
  *                     match the specification.
  * 08-19-13  02.00.26  Added reserved words to MPI2_CONFIG_PAGE_IO_UNIT_7 for
  *			future use.
+ * 12-05-13  02.00.27  Added MPI2_MANPAGE7_FLAG_BASE_ENCLOSURE_LEVEL for
+ *		       MPI2_CONFIG_PAGE_MAN_7.
+ *		       Added EnclosureLevel and ConnectorName fields to
+ *		       MPI2_CONFIG_PAGE_SAS_DEV_0.
+ *		       Added MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID for
+ *		       MPI2_CONFIG_PAGE_SAS_DEV_0.
+ *		       Added EnclosureLevel field to
+ *		       MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
+ *		       Added MPI2_SAS_ENCLS0_FLAGS_ENCL_LEVEL_VALID for
+ *		       MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
  * --------------------------------------------------------------------------
  */
 
@@ -724,6 +734,7 @@ typedef struct _MPI2_CONFIG_PAGE_MAN_7 {
 #define MPI2_MANUFACTURING7_PAGEVERSION                 (0x01)
 
 /*defines for the Flags field */
+#define MPI2_MANPAGE7_FLAG_BASE_ENCLOSURE_LEVEL         (0x00000008)
 #define MPI2_MANPAGE7_FLAG_EVENTREPLAY_SLOT_ORDER       (0x00000002)
 #define MPI2_MANPAGE7_FLAG_USE_SLOT_INFO                (0x00000001)
 
@@ -2633,9 +2644,9 @@ typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_0 {
 	U8
 		ControlGroup;           /*0x2E */
 	U8
-		Reserved1;              /*0x2F */
+		EnclosureLevel;		/*0x2F */
 	U32
-		Reserved2;              /*0x30 */
+		ConnectorName[4];	/*0x30 */
 	U32
 		Reserved3;              /*0x34 */
 } MPI2_CONFIG_PAGE_SAS_DEV_0,
@@ -2643,7 +2654,7 @@ typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_0 {
 	Mpi2SasDevicePage0_t,
 	*pMpi2SasDevicePage0_t;
 
-#define MPI2_SASDEVICE0_PAGEVERSION         (0x08)
+#define MPI2_SASDEVICE0_PAGEVERSION         (0x09)
 
 /*values for SAS Device Page 0 AccessStatus field */
 #define MPI2_SAS_DEVICE0_ASTATUS_NO_ERRORS                  (0x00)
@@ -2683,6 +2694,7 @@ typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_0 {
 #define MPI2_SAS_DEVICE0_FLAGS_SATA_NCQ_SUPPORTED           (0x0020)
 #define MPI2_SAS_DEVICE0_FLAGS_SATA_FUA_SUPPORTED           (0x0010)
 #define MPI2_SAS_DEVICE0_FLAGS_PORT_SELECTOR_ATTACH         (0x0008)
+#define MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID             (0x0002)
 #define MPI2_SAS_DEVICE0_FLAGS_DEVICE_PRESENT               (0x0001)
 
 
@@ -3019,8 +3031,10 @@ typedef struct _MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0 {
 		NumSlots;                   /*0x18 */
 	U16
 		StartSlot;                  /*0x1A */
-	U16
+	U8
 		Reserved2;                  /*0x1C */
+	U8
+		EnclosureLevel;		    /*0x1D */
 	U16
 		SEPDevHandle;               /*0x1E */
 	U32
@@ -3031,9 +3045,10 @@ typedef struct _MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0 {
 	*PTR_MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0,
 	Mpi2SasEnclosurePage0_t, *pMpi2SasEnclosurePage0_t;
 
-#define MPI2_SASENCLOSURE0_PAGEVERSION      (0x03)
+#define MPI2_SASENCLOSURE0_PAGEVERSION      (0x04)
 
 /*values for SAS Enclosure Page 0 Flags field */
+#define MPI2_SAS_ENCLS0_FLAGS_ENCL_LEVEL_VALID      (0x0010)
 #define MPI2_SAS_ENCLS0_FLAGS_MNG_MASK              (0x000F)
 #define MPI2_SAS_ENCLS0_FLAGS_MNG_UNKNOWN           (0x0000)
 #define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_SES           (0x0001)
diff --git a/drivers/scsi/mpt3sas/mpi/mpi2_ioc.h b/drivers/scsi/mpt3sas/mpi/mpi2_ioc.h
index 4908309..d7598cc 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2_ioc.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2_ioc.h
@@ -6,7 +6,7 @@
  *         Title:  MPI IOC, Port, Event, FW Download, and FW Upload messages
  * Creation Date:  October 11, 2006
  *
- * mpi2_ioc.h Version:  02.00.23
+ * mpi2_ioc.h Version:  02.00.24
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -132,6 +132,7 @@
  *			Added MPI2_IOCFACTS_CAPABILITY_RDPQ_ARRAY_CAPABLE.
  *			Added MPI2_FW_DOWNLOAD_ITYPE_PUBLIC_KEY.
  *			Added Encrypted Hash Extended Image.
+ * 12-05-13  02.00.24  Added MPI25_HASH_IMAGE_TYPE_BIOS.
  * --------------------------------------------------------------------------
  */
 
@@ -1598,6 +1599,7 @@ Mpi25EncryptedHashEntry_t, *pMpi25EncryptedHashEntry_t;
 /* values for HashImageType */
 #define MPI25_HASH_IMAGE_TYPE_UNUSED		(0x00)
 #define MPI25_HASH_IMAGE_TYPE_FIRMWARE		(0x01)
+#define MPI25_HASH_IMAGE_TYPE_BIOS              (0x02)
 
 /* values for HashAlgorithm */
 #define MPI25_HASH_ALGORITHM_UNUSED		(0x00)
-- 
2.0.2

[PATCH v2 06/20] [SCSI] mpt3sas: Provides the physical location of sas drives

[Sreekanth Reddy]

This Patch will provide more details of the devices such as slot number, enclosure logical id, enclosure level & connector name in the following scenarios,

- When end device is added in the topology,
- When the end device is removed from the setup,
- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during error handling,
- When any command to the device fails with Sense key Hardware error or Medium error or Unit Attention,
- When firmware returns device error or device not ready status for the end device,
- When a Predicted fault is detected on an end device.

This information can be used by the user to identify the location of the desired drive in the topology.

Driver will get these information by reading the sas device page0.

Changes in v2:
     Fixed the undefined scsih_scsi_ioc_info() function compilation errors which we observe 
only if CONFIG_SCSI_MPT3SAS_LOGGING flag is disabled.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h  |   2 +
 drivers/scsi/mpt3sas/mpt3sas_scsih.c | 240 +++++++++++++++++++++++++++++------
 2 files changed, 203 insertions(+), 39 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index 01d92db..da82a97 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -324,6 +324,8 @@ struct _sas_device {
 	u8	fast_path;
 	u8	pfa_led_on;
 	u8	pend_sas_rphy_add;
+	u8	enclosure_level;
+	u8	connector_name[4];
 };
 
 /**
diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index d457dba..ec3b3d3 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -585,6 +585,22 @@ _scsih_sas_device_remove(struct MPT3SAS_ADAPTER *ioc,
 
 	if (!sas_device)
 		return;
+	pr_info(MPT3SAS_FMT
+	    "removing handle(0x%04x), sas_addr(0x%016llx)\n",
+	    ioc->name, sas_device->handle,
+	    (unsigned long long) sas_device->sas_address);
+
+	if (sas_device->enclosure_handle != 0)
+		pr_info(MPT3SAS_FMT
+		   "removing enclosure logical id(0x%016llx), slot(%d)\n",
+		   ioc->name, (unsigned long long)
+		   sas_device->enclosure_logical_id, sas_device->slot);
+
+	if (sas_device->connector_name[0] != '\0')
+		pr_info(MPT3SAS_FMT
+		   "removing enclosure level(0x%04x), connector name( %s)\n",
+		   ioc->name, sas_device->enclosure_level,
+		   sas_device->connector_name);
 
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_del(&sas_device->list);
@@ -663,6 +679,18 @@ _scsih_sas_device_add(struct MPT3SAS_ADAPTER *ioc,
 		ioc->name, __func__, sas_device->handle,
 		(unsigned long long)sas_device->sas_address));
 
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure logical id(0x%016llx), slot( %d)\n",
+		    ioc->name, __func__, (unsigned long long)
+		    sas_device->enclosure_logical_id, sas_device->slot));
+
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure level(0x%04x), connector name( %s)\n",
+		    ioc->name, __func__,
+		    sas_device->enclosure_level, sas_device->connector_name));
+
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_add_tail(&sas_device->list, &ioc->sas_device_list);
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
@@ -704,6 +732,18 @@ _scsih_sas_device_init_add(struct MPT3SAS_ADAPTER *ioc,
 		__func__, sas_device->handle,
 		(unsigned long long)sas_device->sas_address));
 
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure logical id(0x%016llx), slot( %d)\n",
+		    ioc->name, __func__, (unsigned long long)
+		    sas_device->enclosure_logical_id, sas_device->slot));
+
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enclosure level(0x%04x), connector name( %s)\n",
+		    ioc->name, __func__, sas_device->enclosure_level,
+		    sas_device->connector_name));
+
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_add_tail(&sas_device->list, &ioc->sas_device_init_list);
 	_scsih_determine_boot_device(ioc, sas_device, 0);
@@ -1772,10 +1812,16 @@ _scsih_slave_configure(struct scsi_device *sdev)
 	    "sas_addr(0x%016llx), phy(%d), device_name(0x%016llx)\n",
 	    ds, handle, (unsigned long long)sas_device->sas_address,
 	    sas_device->phy, (unsigned long long)sas_device->device_name);
-	sdev_printk(KERN_INFO, sdev,
-		"%s: enclosure_logical_id(0x%016llx), slot(%d)\n",
-		ds, (unsigned long long)
-	    sas_device->enclosure_logical_id, sas_device->slot);
+	if (sas_device->enclosure_handle != 0)
+		sdev_printk(KERN_INFO, sdev,
+		     "%s: enclosure_logical_id(0x%016llx), slot(%d)\n",
+		     ds, (unsigned long long)
+		     sas_device->enclosure_logical_id, sas_device->slot);
+	if (sas_device->connector_name[0] != '\0')
+		sdev_printk(KERN_INFO, sdev,
+		     "%s: enclosure level(0x%04x), connector name( %s)\n",
+		     ds, sas_device->enclosure_level,
+		     sas_device->connector_name);
 
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 
@@ -2189,10 +2235,17 @@ _scsih_tm_display_info(struct MPT3SAS_ADAPTER *ioc, struct scsi_cmnd *scmd)
 			    sas_device->handle,
 			    (unsigned long long)sas_device->sas_address,
 			    sas_device->phy);
-			starget_printk(KERN_INFO, starget,
-			    "enclosure_logical_id(0x%016llx), slot(%d)\n",
-			   (unsigned long long)sas_device->enclosure_logical_id,
-			    sas_device->slot);
+			if (sas_device->enclosure_handle != 0)
+				starget_printk(KERN_INFO, starget,
+				 "enclosure_logical_id(0x%016llx), slot(%d)\n",
+				 (unsigned long long)
+				 sas_device->enclosure_logical_id,
+				 sas_device->slot);
+			if (sas_device->connector_name)
+				starget_printk(KERN_INFO, starget,
+				"enclosure level(0x%04x),connector name(%s)\n",
+				 sas_device->enclosure_level,
+				 sas_device->connector_name);
 		}
 		spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 	}
@@ -2813,6 +2866,18 @@ _scsih_tm_tr_send(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 			"setting delete flag: handle(0x%04x), sas_addr(0x%016llx)\n",
 			ioc->name, handle,
 		    (unsigned long long)sas_address));
+		if (sas_device->enclosure_handle != 0)
+			dewtprintk(ioc, pr_info(MPT3SAS_FMT
+			 "setting delete flag:enclosure logical id(0x%016llx),"
+			 " slot(%d)\n", ioc->name, (unsigned long long)
+			  sas_device->enclosure_logical_id,
+			  sas_device->slot));
+		if (sas_device->connector_name)
+			dewtprintk(ioc, pr_info(MPT3SAS_FMT
+			 "setting delete flag: enclosure level(0x%04x),"
+			 " connector name( %s)\n", ioc->name,
+			  sas_device->enclosure_level,
+			  sas_device->connector_name));
 		_scsih_ublock_io_device(ioc, sas_address);
 		sas_target_priv_data->handle = MPT3SAS_INVALID_DEVICE_HANDLE;
 	}
@@ -3828,10 +3893,19 @@ _scsih_scsi_ioc_info(struct MPT3SAS_ADAPTER *ioc, struct scsi_cmnd *scmd,
 				"\tsas_address(0x%016llx), phy(%d)\n",
 				ioc->name, (unsigned long long)
 			    sas_device->sas_address, sas_device->phy);
-			pr_warn(MPT3SAS_FMT
-			    "\tenclosure_logical_id(0x%016llx), slot(%d)\n",
-			    ioc->name, (unsigned long long)
-			    sas_device->enclosure_logical_id, sas_device->slot);
+			if (sas_device->enclosure_handle != 0)
+				pr_warn(MPT3SAS_FMT
+				  "\tenclosure_logical_id(0x%016llx),"
+				  "slot(%d)\n", ioc->name,
+				  (unsigned long long)
+				  sas_device->enclosure_logical_id,
+				  sas_device->slot);
+			if (sas_device->connector_name[0])
+				pr_warn(MPT3SAS_FMT
+				  "\tenclosure level(0x%04x),"
+				  " connector name( %s)\n", ioc->name,
+				  sas_device->enclosure_level,
+				  sas_device->connector_name);
 		}
 		spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 	}
@@ -4006,7 +4080,16 @@ _scsih_smart_predicted_fault(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 		spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 		return;
 	}
-	starget_printk(KERN_WARNING, starget, "predicted fault\n");
+	if (sas_device->enclosure_handle != 0)
+		starget_printk(KERN_INFO, starget, "predicted fault, "
+			"enclosure logical id(0x%016llx), slot(%d)\n",
+			(unsigned long long)sas_device->enclosure_logical_id,
+			sas_device->slot);
+	if (sas_device->connector_name[0] != '\0')
+		starget_printk(KERN_WARNING, starget, "predicted fault, "
+			"enclosure level(0x%04x), connector name( %s)\n",
+			sas_device->enclosure_level,
+			sas_device->connector_name);
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 
 	if (ioc->pdev->subsystem_vendor == PCI_VENDOR_ID_IBM)
@@ -4126,8 +4209,15 @@ _scsih_io_done(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 msix_index, u32 reply)
 			_scsih_smart_predicted_fault(ioc,
 			    le16_to_cpu(mpi_reply->DevHandle));
 		mpt3sas_trigger_scsi(ioc, data.skey, data.asc, data.ascq);
-	}
 
+#ifdef CONFIG_SCSI_MPT3SAS_LOGGING
+		if (!(ioc->logging_level & MPT_DEBUG_REPLY) &&
+		     ((scmd->sense_buffer[2] == UNIT_ATTENTION) ||
+		     (scmd->sense_buffer[2] == MEDIUM_ERROR) ||
+		     (scmd->sense_buffer[2] == HARDWARE_ERROR)))
+			_scsih_scsi_ioc_info(ioc, scmd, mpi_reply, smid);
+#endif
+	}
 	switch (ioc_status) {
 	case MPI2_IOCSTATUS_BUSY:
 	case MPI2_IOCSTATUS_INSUFFICIENT_RESOURCES:
@@ -4795,6 +4885,16 @@ _scsih_check_device(struct MPT3SAS_ADAPTER *ioc,
 			sas_device->handle, handle);
 		sas_target_priv_data->handle = handle;
 		sas_device->handle = handle;
+		if (sas_device_pg0.Flags &
+		     MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
+			sas_device->enclosure_level =
+				le16_to_cpu(sas_device_pg0.EnclosureLevel);
+			memcpy(&sas_device->connector_name[0],
+				&sas_device_pg0.ConnectorName[0], 4);
+		} else {
+			sas_device->enclosure_level = 0;
+			sas_device->connector_name[0] = '\0';
+		}
 	}
 
 	/* check if device is present */
@@ -4901,14 +5001,24 @@ _scsih_add_device(struct MPT3SAS_ADAPTER *ioc, u16 handle, u8 phy_num,
 		    ioc->name, __FILE__, __LINE__, __func__);
 	sas_device->enclosure_handle =
 	    le16_to_cpu(sas_device_pg0.EnclosureHandle);
-	sas_device->slot =
-	    le16_to_cpu(sas_device_pg0.Slot);
+	if (sas_device->enclosure_handle != 0)
+		sas_device->slot =
+		    le16_to_cpu(sas_device_pg0.Slot);
 	sas_device->device_info = device_info;
 	sas_device->sas_address = sas_address;
 	sas_device->phy = sas_device_pg0.PhyNum;
 	sas_device->fast_path = (le16_to_cpu(sas_device_pg0.Flags) &
 	    MPI25_SAS_DEVICE0_FLAGS_FAST_PATH_CAPABLE) ? 1 : 0;
 
+	if (sas_device_pg0.Flags & MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
+		sas_device->enclosure_level =
+			le16_to_cpu(sas_device_pg0.EnclosureLevel);
+		memcpy(&sas_device->connector_name[0],
+			&sas_device_pg0.ConnectorName[0], 4);
+	} else {
+		sas_device->enclosure_level = 0;
+		sas_device->connector_name[0] = '\0';
+	}
 	/* get enclosure_logical_id */
 	if (sas_device->enclosure_handle && !(mpt3sas_config_get_enclosure_pg0(
 	   ioc, &mpi_reply, &enclosure_pg0, MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE,
@@ -4950,6 +5060,18 @@ _scsih_remove_device(struct MPT3SAS_ADAPTER *ioc,
 		ioc->name, __func__,
 	    sas_device->handle, (unsigned long long)
 	    sas_device->sas_address));
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: enter: enclosure logical id(0x%016llx), slot(%d)\n",
+		    ioc->name, __func__,
+		    (unsigned long long)sas_device->enclosure_logical_id,
+		    sas_device->slot));
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		  "%s: enter: enclosure level(0x%04x), connector name( %s)\n",
+		  ioc->name, __func__,
+		  sas_device->enclosure_level,
+		  sas_device->connector_name));
 
 	if (sas_device->starget && sas_device->starget->hostdata) {
 		sas_target_priv_data = sas_device->starget->hostdata;
@@ -4966,12 +5088,34 @@ _scsih_remove_device(struct MPT3SAS_ADAPTER *ioc,
 		"removing handle(0x%04x), sas_addr(0x%016llx)\n",
 		ioc->name, sas_device->handle,
 	    (unsigned long long) sas_device->sas_address);
+	if (sas_device->enclosure_handle != 0)
+		pr_info(MPT3SAS_FMT
+		  "removing : enclosure logical id(0x%016llx), slot(%d)\n",
+		  ioc->name,
+		  (unsigned long long)sas_device->enclosure_logical_id,
+		  sas_device->slot);
+	if (sas_device->connector_name[0] != '\0')
+		pr_info(MPT3SAS_FMT
+		  "removing enclosure level(0x%04x), connector name( %s)\n",
+		  ioc->name, sas_device->enclosure_level,
+		  sas_device->connector_name);
 
 	dewtprintk(ioc, pr_info(MPT3SAS_FMT
 		"%s: exit: handle(0x%04x), sas_addr(0x%016llx)\n",
 		ioc->name, __func__,
-	    sas_device->handle, (unsigned long long)
-	    sas_device->sas_address));
+		sas_device->handle, (unsigned long long)
+		sas_device->sas_address));
+	if (sas_device->enclosure_handle != 0)
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: exit: enclosure logical id(0x%016llx), slot(%d)\n",
+		    ioc->name, __func__,
+		    (unsigned long long)sas_device->enclosure_logical_id,
+		    sas_device->slot));
+	if (sas_device->connector_name[0] != '\0')
+		dewtprintk(ioc, pr_info(MPT3SAS_FMT
+		    "%s: exit: enclosure level(0x%04x), connector name(%s)\n",
+		    ioc->name, __func__, sas_device->enclosure_level,
+		    sas_device->connector_name));
 
 	kfree(sas_device);
 }
@@ -6364,9 +6508,7 @@ _scsih_prep_device_scan(struct MPT3SAS_ADAPTER *ioc)
 /**
  * _scsih_mark_responding_sas_device - mark a sas_devices as responding
  * @ioc: per adapter object
- * @sas_address: sas address
- * @slot: enclosure slot id
- * @handle: device handle
+ * @sas_device_pg0: SAS Device page 0
  *
  * After host reset, find out whether devices are still responding.
  * Used in _scsih_remove_unresponsive_sas_devices.
@@ -6374,8 +6516,8 @@ _scsih_prep_device_scan(struct MPT3SAS_ADAPTER *ioc)
  * Return nothing.
  */
 static void
-_scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
-	u16 slot, u16 handle)
+_scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc,
+Mpi2SasDevicePage0_t *sas_device_pg0)
 {
 	struct MPT3SAS_TARGET *sas_target_priv_data = NULL;
 	struct scsi_target *starget;
@@ -6384,8 +6526,8 @@ _scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
 
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	list_for_each_entry(sas_device, &ioc->sas_device_list, list) {
-		if (sas_device->sas_address == sas_address &&
-		    sas_device->slot == slot) {
+		if ((sas_device->sas_address == sas_device_pg0->SASAddress) &&
+			(sas_device->slot == sas_device_pg0->Slot)) {
 			sas_device->responding = 1;
 			starget = sas_device->starget;
 			if (starget && starget->hostdata) {
@@ -6394,22 +6536,40 @@ _scsih_mark_responding_sas_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
 				sas_target_priv_data->deleted = 0;
 			} else
 				sas_target_priv_data = NULL;
-			if (starget)
+			if (starget) {
 				starget_printk(KERN_INFO, starget,
-				    "handle(0x%04x), sas_addr(0x%016llx), "
-				    "enclosure logical id(0x%016llx), "
-				    "slot(%d)\n", handle,
-				    (unsigned long long)sas_device->sas_address,
+				    "handle(0x%04x), sas_addr(0x%016llx)\n",
+				    sas_device_pg0->DevHandle,
 				    (unsigned long long)
-				    sas_device->enclosure_logical_id,
-				    sas_device->slot);
-			if (sas_device->handle == handle)
+				    sas_device->sas_address);
+
+				if (sas_device->enclosure_handle != 0)
+					starget_printk(KERN_INFO, starget,
+					 "enclosure logical id(0x%016llx),"
+					 " slot(%d)\n",
+					 (unsigned long long)
+					 sas_device->enclosure_logical_id,
+					 sas_device->slot);
+			}
+			if (sas_device_pg0->Flags &
+			      MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
+				sas_device->enclosure_level =
+				   le16_to_cpu(sas_device_pg0->EnclosureLevel);
+				memcpy(&sas_device->connector_name[0],
+					&sas_device_pg0->ConnectorName[0], 4);
+			} else {
+				sas_device->enclosure_level = 0;
+				sas_device->connector_name[0] = '\0';
+			}
+
+			if (sas_device->handle == sas_device_pg0->DevHandle)
 				goto out;
 			pr_info("\thandle changed from(0x%04x)!!!\n",
 			    sas_device->handle);
-			sas_device->handle = handle;
+			sas_device->handle = sas_device_pg0->DevHandle;
 			if (sas_target_priv_data)
-				sas_target_priv_data->handle = handle;
+				sas_target_priv_data->handle =
+					sas_device_pg0->DevHandle;
 			goto out;
 		}
 	}
@@ -6448,13 +6608,15 @@ _scsih_search_responding_sas_devices(struct MPT3SAS_ADAPTER *ioc)
 		    MPI2_IOCSTATUS_MASK;
 		if (ioc_status != MPI2_IOCSTATUS_SUCCESS)
 			break;
-		handle = le16_to_cpu(sas_device_pg0.DevHandle);
+		handle = sas_device_pg0.DevHandle =
+				le16_to_cpu(sas_device_pg0.DevHandle);
 		device_info = le32_to_cpu(sas_device_pg0.DeviceInfo);
 		if (!(_scsih_is_end_device(device_info)))
 			continue;
-		_scsih_mark_responding_sas_device(ioc,
-		    le64_to_cpu(sas_device_pg0.SASAddress),
-		    le16_to_cpu(sas_device_pg0.Slot), handle);
+		sas_device_pg0.SASAddress =
+				le64_to_cpu(sas_device_pg0.SASAddress);
+		sas_device_pg0.Slot = le16_to_cpu(sas_device_pg0.Slot);
+		_scsih_mark_responding_sas_device(ioc, &sas_device_pg0);
 	}
 
  out:
-- 
2.0.2

[PATCH v2 07/20] [SCSI] mpt3sas: Bump mpt3sas Driver version to v5.100.00.00

[Sreekanth Reddy]

Bump mpt3sas Driver version to v5.100.00.00

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index da82a97..d635612 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -71,8 +71,8 @@
 #define MPT3SAS_DRIVER_NAME		"mpt3sas"
 #define MPT3SAS_AUTHOR "Avago Technologies <MPT-FusionLinux.pdl@avagotech.com>"
 #define MPT3SAS_DESCRIPTION	"LSI MPT Fusion SAS 3.0 Device Driver"
-#define MPT3SAS_DRIVER_VERSION		"04.100.00.00"
-#define MPT3SAS_MAJOR_VERSION		4
+#define MPT3SAS_DRIVER_VERSION		"05.100.00.00"
+#define MPT3SAS_MAJOR_VERSION		5
 #define MPT3SAS_MINOR_VERSION		100
 #define MPT3SAS_BUILD_VERSION		0
 #define MPT3SAS_RELEASE_VERSION	00
-- 
2.0.2

[PATCH v2 08/20] [SCSI] mpt3sas: Update MPI2 strings to MPI2.5

[Sreekanth Reddy]

Update MPI2 strings to MPI2.5.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 3 +--
 drivers/scsi/mpt3sas/mpt3sas_base.h | 1 -
 2 files changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index bf2d7dc..8730160 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -3924,7 +3924,7 @@ _base_send_ioc_init(struct MPT3SAS_ADAPTER *ioc, int sleep_flag)
 	mpi_request.WhoInit = MPI2_WHOINIT_HOST_DRIVER;
 	mpi_request.VF_ID = 0; /* TODO */
 	mpi_request.VP_ID = 0;
-	mpi_request.MsgVersion = cpu_to_le16(MPI2_VERSION);
+	mpi_request.MsgVersion = cpu_to_le16(MPI25_VERSION);
 	mpi_request.HeaderVersion = cpu_to_le16(MPI2_HEADER_VERSION);
 
 	if (_base_is_controller_msix_enabled(ioc))
@@ -4793,7 +4793,6 @@ mpt3sas_base_attach(struct MPT3SAS_ADAPTER *ioc)
 	ioc->build_sg_scmd = &_base_build_sg_scmd_ieee;
 	ioc->build_sg = &_base_build_sg_ieee;
 	ioc->build_zero_len_sge = &_base_build_zero_len_sge_ieee;
-	ioc->mpi25 = 1;
 	ioc->sge_size_ieee = sizeof(Mpi2IeeeSgeSimple64_t);
 
 	/*
diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index d635612..c0c774f 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -826,7 +826,6 @@ struct MPT3SAS_ADAPTER {
 	MPT_BUILD_SG_SCMD build_sg_scmd;
 	MPT_BUILD_SG    build_sg;
 	MPT_BUILD_ZERO_LEN_SGE build_zero_len_sge;
-	u8              mpi25;
 	u16             sge_size_ieee;
 
 	/* function ptr for MPI sg elements only */
-- 
2.0.2

[PATCH v2 09/20] [SCSI] mpt3sas: MPI 2.5 Rev J (2.5.5) specification and 2.00.34 header files

[Sreekanth Reddy]

Following is the change set,

1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1.
2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpi/mpi2.h      |  5 +++--
 drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h | 14 ++++++++++++--
 drivers/scsi/mpt3sas/mpi/mpi2_tool.h |  4 +++-
 3 files changed, 18 insertions(+), 5 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpi/mpi2.h b/drivers/scsi/mpt3sas/mpi/mpi2.h
index d730c5c..c2d127c 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2.h
@@ -8,7 +8,7 @@
  *                 scatter/gather formats.
  * Creation Date:  June 21, 2006
  *
- * mpi2.h Version:  02.00.33
+ * mpi2.h Version:  02.00.34
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -90,6 +90,7 @@
  * 04-17-13  02.00.31  Bumped MPI2_HEADER_VERSION_UNIT.
  * 08-19-13  02.00.32  Bumped MPI2_HEADER_VERSION_UNIT.
  * 12-05-13  02.00.33  Bumped MPI2_HEADER_VERSION_UNIT.
+ * 01-08-14  02.00.34  Bumped MPI2_HEADER_VERSION_UNIT
  * --------------------------------------------------------------------------
  */
 
@@ -123,7 +124,7 @@
 #define MPI2_VERSION_02_05                  (0x0205)
 
 /*Unit and Dev versioning for this MPI header set */
-#define MPI2_HEADER_VERSION_UNIT            (0x21)
+#define MPI2_HEADER_VERSION_UNIT            (0x22)
 #define MPI2_HEADER_VERSION_DEV             (0x00)
 #define MPI2_HEADER_VERSION_UNIT_MASK       (0xFF00)
 #define MPI2_HEADER_VERSION_UNIT_SHIFT      (8)
diff --git a/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h b/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
index 62dfbf6..cf2b6bf 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
@@ -6,7 +6,7 @@
  *         Title:  MPI Configuration messages and pages
  * Creation Date:  November 10, 2006
  *
- *   mpi2_cnfg.h Version:  02.00.27
+ *   mpi2_cnfg.h Version:  02.00.28
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -175,6 +175,8 @@
  *		       MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
  *		       Added MPI2_SAS_ENCLS0_FLAGS_ENCL_LEVEL_VALID for
  *		       MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
+ * 01-08-14  02.00.28  Added more defines for the BiosOptions field of
+ *		       MPI2_CONFIG_PAGE_BIOS_1.
  * --------------------------------------------------------------------------
  */
 
@@ -1334,9 +1336,17 @@ typedef struct _MPI2_CONFIG_PAGE_BIOS_1 {
 	*PTR_MPI2_CONFIG_PAGE_BIOS_1,
 	Mpi2BiosPage1_t, *pMpi2BiosPage1_t;
 
-#define MPI2_BIOSPAGE1_PAGEVERSION                      (0x05)
+#define MPI2_BIOSPAGE1_PAGEVERSION                      (0x06)
 
 /*values for BIOS Page 1 BiosOptions field */
+#define MPI2_BIOSPAGE1_OPTIONS_X86_DISABLE_BIOS		(0x00000400)
+
+#define MPI2_BIOSPAGE1_OPTIONS_MASK_REGISTRATION_UEFI_BSD	(0x00000300)
+#define MPI2_BIOSPAGE1_OPTIONS_USE_BIT0_REGISTRATION_UEFI_BSD	(0x00000000)
+#define MPI2_BIOSPAGE1_OPTIONS_FULL_REGISTRATION_UEFI_BSD	(0x00000100)
+#define MPI2_BIOSPAGE1_OPTIONS_ADAPTER_REGISTRATION_UEFI_BSD	(0x00000200)
+#define MPI2_BIOSPAGE1_OPTIONS_DISABLE_REGISTRATION_UEFI_BSD	(0x00000300)
+
 #define MPI2_BIOSPAGE1_OPTIONS_MASK_OEM_ID                  (0x000000F0)
 #define MPI2_BIOSPAGE1_OPTIONS_LSI_OEM_ID                   (0x00000000)
 
diff --git a/drivers/scsi/mpt3sas/mpi/mpi2_tool.h b/drivers/scsi/mpt3sas/mpi/mpi2_tool.h
index 904910d..1629e5b 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2_tool.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2_tool.h
@@ -6,7 +6,7 @@
  *         Title:  MPI diagnostic tool structures and definitions
  * Creation Date:  March 26, 2007
  *
- *   mpi2_tool.h Version:  02.00.11
+ *   mpi2_tool.h Version:  02.00.12
  *
  * Version History
  * ---------------
@@ -33,6 +33,7 @@
  * 07-26-12  02.00.10  Modified MPI2_TOOLBOX_DIAGNOSTIC_CLI_REQUEST so that
  *                     it uses MPI Chain SGE as well as MPI Simple SGE.
  * 08-19-13  02.00.11  Added MPI2_TOOLBOX_TEXT_DISPLAY_TOOL and related info.
+ * 01-08-14  02.00.12  Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC.
  * --------------------------------------------------------------------------
  */
 
@@ -100,6 +101,7 @@ typedef struct _MPI2_TOOLBOX_CLEAN_REQUEST {
 #define MPI2_TOOLBOX_CLEAN_OTHER_PERSIST_PAGES      (0x20000000)
 #define MPI2_TOOLBOX_CLEAN_FW_CURRENT               (0x10000000)
 #define MPI2_TOOLBOX_CLEAN_FW_BACKUP                (0x08000000)
+#define MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC   (0x04000000)
 #define MPI2_TOOLBOX_CLEAN_MEGARAID                 (0x02000000)
 #define MPI2_TOOLBOX_CLEAN_INITIALIZATION           (0x01000000)
 #define MPI2_TOOLBOX_CLEAN_FLASH                    (0x00000004)
-- 
2.0.2

[PATCH v2 10/20] [SCSI] mpt3sas: Add branding string support for OEM's HBA

[Sreekanth Reddy]

Added the following Dell branding to the mpt3sas driver.

"VendorID"   "DeviceID"  "SubsystemVendor ID"  "SubsystemDevice ID"  Dell Branding String
0x1000        0x0097          0x1028                 0x1F46            DELL 12Gbps HBA

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 36 ++++++++++++++++++++++++++++++++++++
 drivers/scsi/mpt3sas/mpt3sas_base.h | 11 +++++++++++
 2 files changed, 47 insertions(+)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 8730160..e8b93a8 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -2365,6 +2365,41 @@ _base_display_intel_branding(struct MPT3SAS_ADAPTER *ioc)
 
 
 /**
+ * _base_display_dell_branding - Display branding string
+ * @ioc: per adapter object
+ *
+ * Return nothing.
+ */
+static void
+_base_display_dell_branding(struct MPT3SAS_ADAPTER *ioc)
+{
+	if (ioc->pdev->subsystem_vendor != PCI_VENDOR_ID_DELL)
+		return;
+
+	switch (ioc->pdev->device) {
+	case MPI25_MFGPAGE_DEVID_SAS3008:
+		switch (ioc->pdev->subsystem_device) {
+		case MPT3SAS_DELL_12G_HBA_SSDID:
+			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
+				MPT3SAS_DELL_12G_HBA_BRANDING);
+			break;
+		default:
+			pr_info(MPT3SAS_FMT
+			   "Dell 12Gbps HBA: Subsystem ID: 0x%X\n", ioc->name,
+			   ioc->pdev->subsystem_device);
+			break;
+		}
+		break;
+	default:
+		pr_info(MPT3SAS_FMT
+			"Dell 12Gbps HBA: Subsystem ID: 0x%X\n", ioc->name,
+			ioc->pdev->subsystem_device);
+		break;
+	}
+}
+
+
+/**
  * _base_display_ioc_capabilities - Disply IOC's capabilities.
  * @ioc: per adapter object
  *
@@ -2394,6 +2429,7 @@ _base_display_ioc_capabilities(struct MPT3SAS_ADAPTER *ioc)
 	    bios_version & 0x000000FF);
 
 	_base_display_intel_branding(ioc);
+	_base_display_dell_branding(ioc);
 
 	pr_info(MPT3SAS_FMT "Protocol=(", ioc->name);
 
diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index c0c774f..a5a34f3 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -152,6 +152,17 @@
 #define MPT3SAS_INTEL_RS3UC080_SSDID    0x3524
 
 /*
+ * Dell HBA branding
+ */
+#define MPT3SAS_DELL_12G_HBA_BRANDING       \
+	"Dell 12Gbps HBA"
+
+/*
+ * Dell HBA SSDIDs
+ */
+#define MPT3SAS_DELL_12G_HBA_SSDID	0x1F46
+
+/*
  * status bits for ioc->diag_buffer_status
  */
 #define MPT3_DIAG_BUFFER_IS_REGISTERED	(0x01)
-- 
2.0.2

[PATCH v2 11/20] [SCSI] mpt3sas: Add branding string support for OEM custom HBA

[Sreekanth Reddy]

Add the following OEM's branding to the mpt3sas driver.

"VendorID"   "DeviceID"  "SubsystemVendor ID"   "SubsystemDevice ID"  Cisco Branding String
0x1000         0x97         SVID = 0x1137             0x014C          Cisco 9300-8E 12G SAS HBA

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 34 ++++++++++++++++++++++++++++++++++
 drivers/scsi/mpt3sas/mpt3sas_base.h | 11 +++++++++++
 2 files changed, 45 insertions(+)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index e8b93a8..4f82687 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -2398,6 +2398,39 @@ _base_display_dell_branding(struct MPT3SAS_ADAPTER *ioc)
 	}
 }
 
+/**
+ * _base_display_cisco_branding - Display branding string
+ * @ioc: per adapter object
+ *
+ * Return nothing.
+ */
+static void
+_base_display_cisco_branding(struct MPT3SAS_ADAPTER *ioc)
+{
+	if (ioc->pdev->subsystem_vendor != PCI_VENDOR_ID_CISCO)
+		return;
+
+	switch (ioc->pdev->device) {
+	case MPI25_MFGPAGE_DEVID_SAS3008:
+		switch (ioc->pdev->subsystem_device) {
+		case MPT3SAS_CISCO_12G_HBA_SSDID:
+			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
+				MPT3SAS_CISCO_12G_HBA_BRANDING);
+			break;
+		default:
+			pr_info(MPT3SAS_FMT
+			  "Cisco 12Gbps SAS HBA: Subsystem ID: 0x%X\n",
+			  ioc->name, ioc->pdev->subsystem_device);
+			break;
+		}
+		break;
+	default:
+		 pr_info(MPT3SAS_FMT
+			"Cisco 12Gbps SAS HBA: Subsystem ID: 0x%X\n",
+			ioc->name, ioc->pdev->subsystem_device);
+		break;
+	}
+}
 
 /**
  * _base_display_ioc_capabilities - Disply IOC's capabilities.
@@ -2430,6 +2463,7 @@ _base_display_ioc_capabilities(struct MPT3SAS_ADAPTER *ioc)
 
 	_base_display_intel_branding(ioc);
 	_base_display_dell_branding(ioc);
+	_base_display_cisco_branding(ioc);
 
 	pr_info(MPT3SAS_FMT "Protocol=(", ioc->name);
 
diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index a5a34f3..736682c 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -163,6 +163,17 @@
 #define MPT3SAS_DELL_12G_HBA_SSDID	0x1F46
 
 /*
+ * Cisco HBA branding
+ */
+#define MPT3SAS_CISCO_12G_HBA_BRANDING       \
+	"Cisco 9300-8E 12G SAS HBA"
+
+/*
+ * Cisco HBA SSSDIDs
+ */
+ #define MPT3SAS_CISCO_12G_HBA_SSDID  0x14C
+
+/*
  * status bits for ioc->diag_buffer_status
  */
 #define MPT3_DIAG_BUFFER_IS_REGISTERED	(0x01)
-- 
2.0.2

[PATCH v2 12/20] [SCSI] mpt3sas: Bump mpt3sas driver version to v6.100.00.00

[Sreekanth Reddy]

Bump mpt3sas driver version to v6.100.00.00.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index 736682c..4196fbb 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -71,8 +71,8 @@
 #define MPT3SAS_DRIVER_NAME		"mpt3sas"
 #define MPT3SAS_AUTHOR "Avago Technologies <MPT-FusionLinux.pdl@avagotech.com>"
 #define MPT3SAS_DESCRIPTION	"LSI MPT Fusion SAS 3.0 Device Driver"
-#define MPT3SAS_DRIVER_VERSION		"05.100.00.00"
-#define MPT3SAS_MAJOR_VERSION		5
+#define MPT3SAS_DRIVER_VERSION		"06.100.00.00"
+#define MPT3SAS_MAJOR_VERSION		6
 #define MPT3SAS_MINOR_VERSION		100
 #define MPT3SAS_BUILD_VERSION		0
 #define MPT3SAS_RELEASE_VERSION	00
-- 
2.0.2

[PATCH v2 13/20] [SCSI] mpt3sas: MPI 2.5 Rev K (2.5.6) specifications

[Sreekanth Reddy]

Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35 header files
1) Added a minimum size requirement for target mode command buffers.
2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase Request.
3) For BIOS Page 1, added SSUTimeout field, and added Product Name String Format bits to the BiosOptions field

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpi/mpi2.h      |  5 +++--
 drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h | 17 ++++++++++++++---
 2 files changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpi/mpi2.h b/drivers/scsi/mpt3sas/mpi/mpi2.h
index c2d127c..ec27ad2 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2.h
@@ -8,7 +8,7 @@
  *                 scatter/gather formats.
  * Creation Date:  June 21, 2006
  *
- * mpi2.h Version:  02.00.34
+ * mpi2.h Version:  02.00.35
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -91,6 +91,7 @@
  * 08-19-13  02.00.32  Bumped MPI2_HEADER_VERSION_UNIT.
  * 12-05-13  02.00.33  Bumped MPI2_HEADER_VERSION_UNIT.
  * 01-08-14  02.00.34  Bumped MPI2_HEADER_VERSION_UNIT
+ * 06-13-14  02.00.35  Bumped MPI2_HEADER_VERSION_UNIT.
  * --------------------------------------------------------------------------
  */
 
@@ -124,7 +125,7 @@
 #define MPI2_VERSION_02_05                  (0x0205)
 
 /*Unit and Dev versioning for this MPI header set */
-#define MPI2_HEADER_VERSION_UNIT            (0x22)
+#define MPI2_HEADER_VERSION_UNIT            (0x23)
 #define MPI2_HEADER_VERSION_DEV             (0x00)
 #define MPI2_HEADER_VERSION_UNIT_MASK       (0xFF00)
 #define MPI2_HEADER_VERSION_UNIT_SHIFT      (8)
diff --git a/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h b/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
index cf2b6bf..581fdb3 100644
--- a/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
+++ b/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
@@ -6,7 +6,7 @@
  *         Title:  MPI Configuration messages and pages
  * Creation Date:  November 10, 2006
  *
- *   mpi2_cnfg.h Version:  02.00.28
+ *   mpi2_cnfg.h Version:  02.00.29
  *
  * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
  *       prefix are for use only on MPI v2.5 products, and must not be used
@@ -177,6 +177,8 @@
  *		       MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
  * 01-08-14  02.00.28  Added more defines for the BiosOptions field of
  *		       MPI2_CONFIG_PAGE_BIOS_1.
+ * 06-13-14  02.00.29  Added SSUTimeout field to MPI2_CONFIG_PAGE_BIOS_1, and
+ *		       more defines for the BiosOptions field..
  * --------------------------------------------------------------------------
  */
 
@@ -1324,7 +1326,9 @@ typedef struct _MPI2_CONFIG_PAGE_BIOS_1 {
 	MPI2_CONFIG_PAGE_HEADER Header;                     /*0x00 */
 	U32                     BiosOptions;                /*0x04 */
 	U32                     IOCSettings;                /*0x08 */
-	U32                     Reserved1;                  /*0x0C */
+	U8                      SSUTimeout;                 /*0x0C */
+	U8                      Reserved1;                  /*0x0D */
+	U16                     Reserved2;                  /*0x0E */
 	U32                     DeviceSettings;             /*0x10 */
 	U16                     NumberOfDevices;            /*0x14 */
 	U16                     UEFIVersion;                /*0x16 */
@@ -1336,9 +1340,16 @@ typedef struct _MPI2_CONFIG_PAGE_BIOS_1 {
 	*PTR_MPI2_CONFIG_PAGE_BIOS_1,
 	Mpi2BiosPage1_t, *pMpi2BiosPage1_t;
 
-#define MPI2_BIOSPAGE1_PAGEVERSION                      (0x06)
+#define MPI2_BIOSPAGE1_PAGEVERSION                      (0x07)
 
 /*values for BIOS Page 1 BiosOptions field */
+#define MPI2_BIOSPAGE1_OPTIONS_PNS_MASK                         (0x00003800)
+#define MPI2_BIOSPAGE1_OPTIONS_PNS_PBDHL                        (0x00000000)
+#define MPI2_BIOSPAGE1_OPTIONS_PNS_ENCSLOSURE                   (0x00000800)
+#define MPI2_BIOSPAGE1_OPTIONS_PNS_LWWID                        (0x00001000)
+#define MPI2_BIOSPAGE1_OPTIONS_PNS_PSENS                        (0x00001800)
+#define MPI2_BIOSPAGE1_OPTIONS_PNS_ESPHY                        (0x00002000)
+
 #define MPI2_BIOSPAGE1_OPTIONS_X86_DISABLE_BIOS		(0x00000400)
 
 #define MPI2_BIOSPAGE1_OPTIONS_MASK_REGISTRATION_UEFI_BSD	(0x00000300)
-- 
2.0.2

[PATCH v2 14/20] [SCSI] mpt3sas: Complete the SCSI command with DID_RESET status for log_info value 0x0x32010081

[Sreekanth Reddy]

For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.

The definition of this log info value is
"Virtual IO has failed and has to be retried".

Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.

Changes in v1:
   Defined macro VIRTUAL_IO_FAILED_RETRY for magic a value 0x32010081

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h  | 2 ++
 drivers/scsi/mpt3sas/mpt3sas_scsih.c | 3 +++
 2 files changed, 5 insertions(+)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index 4196fbb..3b03639 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -202,6 +202,8 @@
 #define MFG10_GF0_SSD_DATA_SCRUB_DISABLE       (0x00000008)
 #define MFG10_GF0_SINGLE_DRIVE_R0              (0x00000010)
 
+#define VIRTUAL_IO_FAILED_RETRY			(0x32010081)
+
 /* OEM Specific Flags will come from OEM specific header files */
 struct Mpi2ManufacturingPage10_t {
 	MPI2_CONFIG_PAGE_HEADER	Header;		/* 00h */
diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index 64dd90b..49c412b 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -4241,6 +4241,9 @@ _scsih_io_done(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 msix_index, u32 reply)
 				scmd->device->expecting_cc_ua = 1;
 			}
 			break;
+		} else if (log_info == VIRTUAL_IO_FAILED_RETRY) {
+			scmd->result = DID_RESET << 16;
+			break;
 		}
 		scmd->result = DID_SOFT_ERROR << 16;
 		break;
-- 
2.0.2

[PATCH v2 15/20] [SCSI] mpt3sas: Return host busy error status to SML when DMA mapping of scatter gather list fails for a SCSI command

[Sreekanth Reddy]

scsi_dma_map API will return a negative value (i.e. -ENOMEM)
if DMA mapping of sg lists fails and zero if the sg list in the
SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping
failure case properly.

So, Updated the code to return host busy error status to SCSI MID Layer(SML),
when DMA mapping of scatter gather list fails for a SCSI command.
So that SML will retry this SCSI cmd after some time.

Changes in v2:
    Corrected the typo mistake from "(!sges_left < 0)" to "(sges_left < 0)".

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 4f82687..6e44370 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -1360,7 +1360,7 @@ _base_build_sg_scmd_ieee(struct MPT3SAS_ADAPTER *ioc,
 
 	sg_scmd = scsi_sglist(scmd);
 	sges_left = scsi_dma_map(scmd);
-	if (!sges_left) {
+	if (sges_left < 0) {
 		sdev_printk(KERN_ERR, scmd->device,
 			"pci_map_sg failed: request for %d bytes!\n",
 			scsi_bufflen(scmd));
@@ -1429,7 +1429,7 @@ _base_build_sg_scmd_ieee(struct MPT3SAS_ADAPTER *ioc,
  fill_in_last_segment:
 
 	/* fill the last segment */
-	while (sges_left) {
+	while (sges_left > 0) {
 		if (sges_left == 1)
 			_base_add_sg_single_ieee(sg_local,
 			    simple_sgl_flags_last, 0, sg_dma_len(sg_scmd),
-- 
2.0.2

[PATCH v2 16/20] [SCSI] mpt3sas: Added support for customer specific branding

[Sreekanth Reddy]

Added support for below customer specific brandings

"VendorID"   "DeviceID"  "SubsystemVendor ID"   "SubsystemDevice ID"  Cisco Branding String
0x1000         0x97           0x1137                 0x154           Cisco 9300-8i 12Gbps SAS HBA
0x1000         0x97           0x1137                 0x155           Cisco 12G Modular SAS Pass through Controller
0x1000         0x97           0x1137                 0x156           UCS C3X60 12G SAS Pass through Controller

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 29 +++++++++++++++++++++++++++--
 drivers/scsi/mpt3sas/mpt3sas_base.h | 16 ++++++++++++----
 2 files changed, 39 insertions(+), 6 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 6e44370..dd04ec0 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -2413,9 +2413,17 @@ _base_display_cisco_branding(struct MPT3SAS_ADAPTER *ioc)
 	switch (ioc->pdev->device) {
 	case MPI25_MFGPAGE_DEVID_SAS3008:
 		switch (ioc->pdev->subsystem_device) {
-		case MPT3SAS_CISCO_12G_HBA_SSDID:
+		case MPT3SAS_CISCO_12G_8E_HBA_SSDID:
 			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
-				MPT3SAS_CISCO_12G_HBA_BRANDING);
+				MPT3SAS_CISCO_12G_8E_HBA_BRANDING);
+			break;
+		case MPT3SAS_CISCO_12G_8I_HBA_SSDID:
+			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
+				MPT3SAS_CISCO_12G_8I_HBA_BRANDING);
+			break;
+		case MPT3SAS_CISCO_12G_AVILA_HBA_SSDID:
+			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
+				MPT3SAS_CISCO_12G_AVILA_HBA_BRANDING);
 			break;
 		default:
 			pr_info(MPT3SAS_FMT
@@ -2424,6 +2432,23 @@ _base_display_cisco_branding(struct MPT3SAS_ADAPTER *ioc)
 			break;
 		}
 		break;
+	case MPI25_MFGPAGE_DEVID_SAS3108_1:
+		switch (ioc->pdev->subsystem_device) {
+		case MPT3SAS_CISCO_12G_AVILA_HBA_SSDID:
+			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
+			MPT3SAS_CISCO_12G_AVILA_HBA_BRANDING);
+			break;
+		case MPT3SAS_CISCO_12G_COLUSA_MEZZANINE_HBA_SSDID:
+			pr_info(MPT3SAS_FMT "%s\n", ioc->name,
+			MPT3SAS_CISCO_12G_COLUSA_MEZZANINE_HBA_BRANDING);
+			break;
+		default:
+			pr_info(MPT3SAS_FMT
+			 "Cisco 12Gbps SAS HBA: Subsystem ID: 0x%X\n",
+			 ioc->name, ioc->pdev->subsystem_device);
+			break;
+		}
+		break;
 	default:
 		 pr_info(MPT3SAS_FMT
 			"Cisco 12Gbps SAS HBA: Subsystem ID: 0x%X\n",
diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index 3b03639..87e9000 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -165,13 +165,21 @@
 /*
  * Cisco HBA branding
  */
-#define MPT3SAS_CISCO_12G_HBA_BRANDING       \
-	"Cisco 9300-8E 12G SAS HBA"
-
+#define MPT3SAS_CISCO_12G_8E_HBA_BRANDING		\
+		"Cisco 9300-8E 12G SAS HBA"
+#define MPT3SAS_CISCO_12G_8I_HBA_BRANDING		\
+		"Cisco 9300-8i 12G SAS HBA"
+#define MPT3SAS_CISCO_12G_AVILA_HBA_BRANDING	\
+		"Cisco 12G Modular SAS Pass through Controller"
+#define MPT3SAS_CISCO_12G_COLUSA_MEZZANINE_HBA_BRANDING		\
+		"UCS C3X60 12G SAS Pass through Controller"
 /*
  * Cisco HBA SSSDIDs
  */
- #define MPT3SAS_CISCO_12G_HBA_SSDID  0x14C
+#define MPT3SAS_CISCO_12G_8E_HBA_SSDID  0x14C
+#define MPT3SAS_CISCO_12G_8I_HBA_SSDID  0x154
+#define MPT3SAS_CISCO_12G_AVILA_HBA_SSDID  0x155
+#define MPT3SAS_CISCO_12G_COLUSA_MEZZANINE_HBA_SSDID  0x156
 
 /*
  * status bits for ioc->diag_buffer_status
-- 
2.0.2

[PATCH v2 17/20] [SCSI] mpt3sas: Use alloc_ordered_workqueue() API instead of create_singlethread_workqueue() API

[Sreekanth Reddy]

Created a thread using alloc_ordered_workqueue() API in order to process
the works from firmware Work-queue sequentially instead of
create_singlethread_workqueue() API.

Changes in v1:
    No need to check for backport compatibility in the upstream kernel.
so removing the else section where driver use
create_singlethread_workqueue() API if alloc_ordered_workqueue() API is
not defined, This else section is not required since in the latest upstream
kernel this alloc_ordered_workqueue() API is always defined.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Joe Lawrence <joe.lawrence@stratus.com>
---
 drivers/scsi/mpt3sas/mpt3sas_scsih.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index 49c412b..a136ec8 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -8024,8 +8024,8 @@ _scsih_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	/* event thread */
 	snprintf(ioc->firmware_event_name, sizeof(ioc->firmware_event_name),
 	    "fw_event%d", ioc->id);
-	ioc->firmware_event_thread = create_singlethread_workqueue(
-	    ioc->firmware_event_name);
+	ioc->firmware_event_thread = alloc_ordered_workqueue(
+	    ioc->firmware_event_name, WQ_MEM_RECLAIM);
 	if (!ioc->firmware_event_thread) {
 		pr_err(MPT3SAS_FMT "failure at %s:%d/%s()!\n",
 		    ioc->name, __FILE__, __LINE__, __func__);
-- 
2.0.2

[PATCH v2 18/20] [SCSI] mpt3sas: Call dma_mapping_error() API after mapping an address with dma_map_single() API

[Sreekanth Reddy]

Added dma_mapping_error() API after mapping an address with dma_map_single() API.
Otherwise when CONFIG_DMA_API_DEBUG is enabled in the kernel, then it complains
about mpt3sas driver not calling dma_mapping_error after mapping an address with
dma_map_single

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_transport.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_transport.c b/drivers/scsi/mpt3sas/mpt3sas_transport.c
index 7a7aa68..70fd019 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_transport.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_transport.c
@@ -1964,7 +1964,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy,
 	} else {
 		dma_addr_out = pci_map_single(ioc->pdev, bio_data(req->bio),
 		    blk_rq_bytes(req), PCI_DMA_BIDIRECTIONAL);
-		if (!dma_addr_out) {
+		if (pci_dma_mapping_error(ioc->pdev, dma_addr_out)) {
 			pr_info(MPT3SAS_FMT "%s(): DMA Addr out = NULL\n",
 			    ioc->name, __func__);
 			rc = -ENOMEM;
@@ -1986,7 +1986,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy,
 	} else {
 		dma_addr_in =  pci_map_single(ioc->pdev, bio_data(rsp->bio),
 		    blk_rq_bytes(rsp), PCI_DMA_BIDIRECTIONAL);
-		if (!dma_addr_in) {
+		if (pci_dma_mapping_error(ioc->pdev, dma_addr_in)) {
 			pr_info(MPT3SAS_FMT "%s(): DMA Addr in = NULL\n",
 			    ioc->name, __func__);
 			rc = -ENOMEM;
-- 
2.0.2

[PATCH v2 19/20] [SCSI] mpt3sas: When device is blocked followed by unblock fails, unfreeze the I/Os

[Sreekanth Reddy]

Issue: When the disks are getting discovered and assigned device
handles by the kernel, a device block followed by an unblock
(due to broadcast primitives) issued by the driver is
interspersed by the kernel changing the state of the device.
Therefore the unblock by the driver results in a no operation
within the kernel API.

To fix this one, the below patch checks the return of the unblock API
and performs a block followed by an unblock to unfreeze the block
layer's I/O queue. Sufficient checks and prints are also added in the
driver to identify this condition caused by the kernel.

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_scsih.c | 89 ++++++++++++++++++++++++++++++------
 1 file changed, 75 insertions(+), 14 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index a136ec8..7e5926c 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -2605,6 +2605,75 @@ _scsih_fw_event_cleanup_queue(struct MPT3SAS_ADAPTER *ioc)
 }
 
 /**
+ * _scsih_internal_device_block - block the sdev device
+ * @sdev: per device object
+ * @sas_device_priv_data : per device driver private data
+ *
+ * make sure device is blocked without error, if not
+ * print an error
+ */
+static void
+_scsih_internal_device_block(struct scsi_device *sdev,
+			struct MPT3SAS_DEVICE *sas_device_priv_data)
+{
+	int r = 0;
+
+	sdev_printk(KERN_INFO, sdev, "device_block, handle(0x%04x)\n",
+	    sas_device_priv_data->sas_target->handle);
+	sas_device_priv_data->block = 1;
+
+	r = scsi_internal_device_block(sdev);
+	if (r == -EINVAL)
+		sdev_printk(KERN_WARNING, sdev,
+		    "device_block failed with return(%d) for handle(0x%04x)\n",
+		    sas_device_priv_data->sas_target->handle, r);
+}
+
+/**
+ * _scsih_internal_device_unblock - unblock the sdev device
+ * @sdev: per device object
+ * @sas_device_priv_data : per device driver private data
+ * make sure device is unblocked without error, if not retry
+ * by blocking and then unblocking
+ */
+
+static void
+_scsih_internal_device_unblock(struct scsi_device *sdev,
+			struct MPT3SAS_DEVICE *sas_device_priv_data)
+{
+	int r = 0;
+
+	sdev_printk(KERN_WARNING, sdev, "device_unblock and setting to running, "
+	    "handle(0x%04x)\n", sas_device_priv_data->sas_target->handle);
+	sas_device_priv_data->block = 0;
+	r = scsi_internal_device_unblock(sdev, SDEV_RUNNING);
+	if (r == -EINVAL) {
+		/* The device has been set to SDEV_RUNNING by SD layer during
+		 * device addition but the request queue is still stopped by
+		 * our earlier block call. We need to perform a block again
+		 * to get the device to SDEV_BLOCK and then to SDEV_RUNNING */
+
+		sdev_printk(KERN_WARNING, sdev,
+		    "device_unblock failed with return(%d) for handle(0x%04x) "
+		    "performing a block followed by an unblock\n",
+		    sas_device_priv_data->sas_target->handle, r);
+		sas_device_priv_data->block = 1;
+		r = scsi_internal_device_block(sdev);
+		if (r)
+			sdev_printk(KERN_WARNING, sdev, "retried device_block "
+			    "failed with return(%d) for handle(0x%04x)\n",
+			    sas_device_priv_data->sas_target->handle, r);
+
+		sas_device_priv_data->block = 0;
+		r = scsi_internal_device_unblock(sdev, SDEV_RUNNING);
+		if (r)
+			sdev_printk(KERN_WARNING, sdev, "retried device_unblock"
+			    " failed with return(%d) for handle(0x%04x)\n",
+			    sas_device_priv_data->sas_target->handle, r);
+	}
+}
+
+/**
  * _scsih_ublock_io_all_device - unblock every device
  * @ioc: per adapter object
  *
@@ -2623,11 +2692,10 @@ _scsih_ublock_io_all_device(struct MPT3SAS_ADAPTER *ioc)
 		if (!sas_device_priv_data->block)
 			continue;
 
-		sas_device_priv_data->block = 0;
 		dewtprintk(ioc, sdev_printk(KERN_INFO, sdev,
 			"device_running, handle(0x%04x)\n",
 		    sas_device_priv_data->sas_target->handle));
-		scsi_internal_device_unblock(sdev, SDEV_RUNNING);
+		_scsih_internal_device_unblock(sdev, sas_device_priv_data);
 	}
 }
 
@@ -2652,10 +2720,9 @@ _scsih_ublock_io_device(struct MPT3SAS_ADAPTER *ioc, u64 sas_address)
 		if (sas_device_priv_data->sas_target->sas_address
 		    != sas_address)
 			continue;
-		if (sas_device_priv_data->block) {
-			sas_device_priv_data->block = 0;
-			scsi_internal_device_unblock(sdev, SDEV_RUNNING);
-		}
+		if (sas_device_priv_data->block)
+			_scsih_internal_device_unblock(sdev,
+				sas_device_priv_data);
 	}
 }
 
@@ -2678,10 +2745,7 @@ _scsih_block_io_all_device(struct MPT3SAS_ADAPTER *ioc)
 			continue;
 		if (sas_device_priv_data->block)
 			continue;
-		sas_device_priv_data->block = 1;
-		scsi_internal_device_block(sdev);
-		sdev_printk(KERN_INFO, sdev, "device_blocked, handle(0x%04x)\n",
-		    sas_device_priv_data->sas_target->handle);
+		_scsih_internal_device_block(sdev, sas_device_priv_data);
 	}
 }
 
@@ -2713,10 +2777,7 @@ _scsih_block_io_device(struct MPT3SAS_ADAPTER *ioc, u16 handle)
 			continue;
 		if (sas_device->pend_sas_rphy_add)
 			continue;
-		sas_device_priv_data->block = 1;
-		scsi_internal_device_block(sdev);
-		sdev_printk(KERN_INFO, sdev,
-			"device_blocked, handle(0x%04x)\n", handle);
+		_scsih_internal_device_block(sdev, sas_device_priv_data);
 	}
 }
 
-- 
2.0.2

[PATCH v2 20/20] [SCSI] mpt3sas : Bump mpt3sas driver version to 9.100.00.00

[Sreekanth Reddy]

Bump mpt3sas driver version to 9.100.00.00

Changes in v2:
	Patch version change only.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
---
 drivers/scsi/mpt3sas/mpt3sas_base.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.h b/drivers/scsi/mpt3sas/mpt3sas_base.h
index 87e9000..f0e462b 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.h
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.h
@@ -71,8 +71,8 @@
 #define MPT3SAS_DRIVER_NAME		"mpt3sas"
 #define MPT3SAS_AUTHOR "Avago Technologies <MPT-FusionLinux.pdl@avagotech.com>"
 #define MPT3SAS_DESCRIPTION	"LSI MPT Fusion SAS 3.0 Device Driver"
-#define MPT3SAS_DRIVER_VERSION		"06.100.00.00"
-#define MPT3SAS_MAJOR_VERSION		6
+#define MPT3SAS_DRIVER_VERSION		"09.100.00.00"
+#define MPT3SAS_MAJOR_VERSION		9
 #define MPT3SAS_MINOR_VERSION		100
 #define MPT3SAS_BUILD_VERSION		0
 #define MPT3SAS_RELEASE_VERSION	00
-- 
2.0.2