* [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040
@ 2015-06-11 7:53 ` Jia Hongtao
0 siblings, 0 replies; 6+ messages in thread
From: Jia Hongtao @ 2015-06-11 7:53 UTC (permalink / raw)
To: scottwood; +Cc: edubezval, devicetree, hongtao.jia, robh+dt, linuxppc-dev
This is Thermal Monitoring Unit for QorIQ platform.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
---
Changes of V3:
* Put TMU node directly into t1040si-post.dtsi file.
* Add "fsl,tmu-range" property.
* Change "calibration" property to "fsl,tmu-calibration".
* Update the calibration data.
Changes of V2:
* Provide more details on compatible and calibration properties.
.../devicetree/bindings/thermal/qoriq-thermal.txt | 63 ++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 42 +++++++++++++++
2 files changed, 105 insertions(+)
create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
new file mode 100644
index 0000000..2bc9cb3
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
@@ -0,0 +1,63 @@
+* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs
+
+Required properties:
+- compatible : Must include "fsl,qoriq-tmu". The version of the device is
+ determined by the TMU IP Block Revision Register (IPBRR0) at
+ offset 0x0BF8.
+ Table of correspondences between IPBRR0 values and example chips:
+ Value Device
+ ---------- -----
+ 0x01900102 T1040
+- reg : Address range of TMU registers.
+- interrupts : Contains the interrupt for TMU.
+- fsl,tmu-range : Temperature range for TMU. Including the starting
+ temperature and number of calibration points for each range.
+- fsl,tmu-calibration : Calibration table for TMU. This is required to
+ determine what a specific sensor reading translates to in degrees
+ Celsius. There are four calibration ranges, for each range we need
+ a couple of calibration data formatted like <TTCFGR, TSCFGR>.
+ Freescale provides the data required.
+
+Example:
+
+tmu@f0000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0xf0000 0x1000>;
+ interrupts = <18 2 0 0>;
+ fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
+ fsl,tmu-calibration = <0x00000000 0x00000025
+ 0x00000001 0x00000028
+ 0x00000002 0x0000002d
+ 0x00000003 0x00000031
+ 0x00000004 0x00000036
+ 0x00000005 0x0000003a
+ 0x00000006 0x00000040
+ 0x00000007 0x00000044
+ 0x00000008 0x0000004a
+ 0x00000009 0x0000004f
+ 0x0000000a 0x00000054
+
+ 0x00010000 0x0000000d
+ 0x00010001 0x00000013
+ 0x00010002 0x00000019
+ 0x00010003 0x0000001f
+ 0x00010004 0x00000025
+ 0x00010005 0x0000002d
+ 0x00010006 0x00000033
+ 0x00010007 0x00000043
+ 0x00010008 0x0000004b
+ 0x00010009 0x00000053
+
+ 0x00020000 0x00000010
+ 0x00020001 0x00000017
+ 0x00020002 0x0000001f
+ 0x00020003 0x00000029
+ 0x00020004 0x00000031
+ 0x00020005 0x0000003c
+ 0x00020006 0x00000042
+ 0x00020007 0x0000004d
+ 0x00020008 0x00000056
+
+ 0x00030000 0x00000012
+ 0x00030001 0x0000001d>;
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
index 5cc01be..6d9ca4d 100644
--- a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
@@ -407,6 +407,48 @@
reg = <0xea000 0x4000>;
};
+ tmu@f0000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0xf0000 0x1000>;
+ interrupts = <18 2 0 0>;
+ fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
+ fsl,tmu-calibration = <0x00000000 0x00000025
+ 0x00000001 0x00000028
+ 0x00000002 0x0000002d
+ 0x00000003 0x00000031
+ 0x00000004 0x00000036
+ 0x00000005 0x0000003a
+ 0x00000006 0x00000040
+ 0x00000007 0x00000044
+ 0x00000008 0x0000004a
+ 0x00000009 0x0000004f
+ 0x0000000a 0x00000054
+
+ 0x00010000 0x0000000d
+ 0x00010001 0x00000013
+ 0x00010002 0x00000019
+ 0x00010003 0x0000001f
+ 0x00010004 0x00000025
+ 0x00010005 0x0000002d
+ 0x00010006 0x00000033
+ 0x00010007 0x00000043
+ 0x00010008 0x0000004b
+ 0x00010009 0x00000053
+
+ 0x00020000 0x00000010
+ 0x00020001 0x00000017
+ 0x00020002 0x0000001f
+ 0x00020003 0x00000029
+ 0x00020004 0x00000031
+ 0x00020005 0x0000003c
+ 0x00020006 0x00000042
+ 0x00020007 0x0000004d
+ 0x00020008 0x00000056
+
+ 0x00030000 0x00000012
+ 0x00030001 0x0000001d>;
+ };
+
/include/ "elo3-dma-0.dtsi"
/include/ "elo3-dma-1.dtsi"
/include/ "qoriq-espi-0.dtsi"
--
2.1.0.27.g96db324
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040
@ 2015-06-11 7:53 ` Jia Hongtao
0 siblings, 0 replies; 6+ messages in thread
From: Jia Hongtao @ 2015-06-11 7:53 UTC (permalink / raw)
To: scottwood; +Cc: linuxppc-dev, devicetree, robh+dt, edubezval, hongtao.jia
This is Thermal Monitoring Unit for QorIQ platform.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
---
Changes of V3:
* Put TMU node directly into t1040si-post.dtsi file.
* Add "fsl,tmu-range" property.
* Change "calibration" property to "fsl,tmu-calibration".
* Update the calibration data.
Changes of V2:
* Provide more details on compatible and calibration properties.
.../devicetree/bindings/thermal/qoriq-thermal.txt | 63 ++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 42 +++++++++++++++
2 files changed, 105 insertions(+)
create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
new file mode 100644
index 0000000..2bc9cb3
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
@@ -0,0 +1,63 @@
+* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs
+
+Required properties:
+- compatible : Must include "fsl,qoriq-tmu". The version of the device is
+ determined by the TMU IP Block Revision Register (IPBRR0) at
+ offset 0x0BF8.
+ Table of correspondences between IPBRR0 values and example chips:
+ Value Device
+ ---------- -----
+ 0x01900102 T1040
+- reg : Address range of TMU registers.
+- interrupts : Contains the interrupt for TMU.
+- fsl,tmu-range : Temperature range for TMU. Including the starting
+ temperature and number of calibration points for each range.
+- fsl,tmu-calibration : Calibration table for TMU. This is required to
+ determine what a specific sensor reading translates to in degrees
+ Celsius. There are four calibration ranges, for each range we need
+ a couple of calibration data formatted like <TTCFGR, TSCFGR>.
+ Freescale provides the data required.
+
+Example:
+
+tmu@f0000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0xf0000 0x1000>;
+ interrupts = <18 2 0 0>;
+ fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
+ fsl,tmu-calibration = <0x00000000 0x00000025
+ 0x00000001 0x00000028
+ 0x00000002 0x0000002d
+ 0x00000003 0x00000031
+ 0x00000004 0x00000036
+ 0x00000005 0x0000003a
+ 0x00000006 0x00000040
+ 0x00000007 0x00000044
+ 0x00000008 0x0000004a
+ 0x00000009 0x0000004f
+ 0x0000000a 0x00000054
+
+ 0x00010000 0x0000000d
+ 0x00010001 0x00000013
+ 0x00010002 0x00000019
+ 0x00010003 0x0000001f
+ 0x00010004 0x00000025
+ 0x00010005 0x0000002d
+ 0x00010006 0x00000033
+ 0x00010007 0x00000043
+ 0x00010008 0x0000004b
+ 0x00010009 0x00000053
+
+ 0x00020000 0x00000010
+ 0x00020001 0x00000017
+ 0x00020002 0x0000001f
+ 0x00020003 0x00000029
+ 0x00020004 0x00000031
+ 0x00020005 0x0000003c
+ 0x00020006 0x00000042
+ 0x00020007 0x0000004d
+ 0x00020008 0x00000056
+
+ 0x00030000 0x00000012
+ 0x00030001 0x0000001d>;
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
index 5cc01be..6d9ca4d 100644
--- a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
@@ -407,6 +407,48 @@
reg = <0xea000 0x4000>;
};
+ tmu@f0000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0xf0000 0x1000>;
+ interrupts = <18 2 0 0>;
+ fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
+ fsl,tmu-calibration = <0x00000000 0x00000025
+ 0x00000001 0x00000028
+ 0x00000002 0x0000002d
+ 0x00000003 0x00000031
+ 0x00000004 0x00000036
+ 0x00000005 0x0000003a
+ 0x00000006 0x00000040
+ 0x00000007 0x00000044
+ 0x00000008 0x0000004a
+ 0x00000009 0x0000004f
+ 0x0000000a 0x00000054
+
+ 0x00010000 0x0000000d
+ 0x00010001 0x00000013
+ 0x00010002 0x00000019
+ 0x00010003 0x0000001f
+ 0x00010004 0x00000025
+ 0x00010005 0x0000002d
+ 0x00010006 0x00000033
+ 0x00010007 0x00000043
+ 0x00010008 0x0000004b
+ 0x00010009 0x00000053
+
+ 0x00020000 0x00000010
+ 0x00020001 0x00000017
+ 0x00020002 0x0000001f
+ 0x00020003 0x00000029
+ 0x00020004 0x00000031
+ 0x00020005 0x0000003c
+ 0x00020006 0x00000042
+ 0x00020007 0x0000004d
+ 0x00020008 0x00000056
+
+ 0x00030000 0x00000012
+ 0x00030001 0x0000001d>;
+ };
+
/include/ "elo3-dma-0.dtsi"
/include/ "elo3-dma-1.dtsi"
/include/ "qoriq-espi-0.dtsi"
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 6+ messages in thread
* RE: [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040
2015-06-11 7:53 ` Jia Hongtao
@ 2015-07-09 8:00 ` Hongtao Jia
-1 siblings, 0 replies; 6+ messages in thread
From: Hongtao Jia @ 2015-07-09 8:00 UTC (permalink / raw)
To: Hongtao Jia, Scott Wood
Cc: linuxppc-dev-uLR06cmDAlY/bJ5BZ2RsiQ,
devicetree-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, edubezval-Re5JQEeQqe8AvxtiuMwx3w
Hi Scott,
Patch updated to V3, please help to review.
Thanks.
---
Best Regards,
Hongtao
> -----Original Message-----
> From: Jia Hongtao [mailto:hongtao.jia-KZfg59tc24xl57MIdRCFDg@public.gmane.org]
> Sent: Thursday, June 11, 2015 3:53 PM
> To: Wood Scott-B07421
> Cc: linuxppc-dev-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org; devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org;
> robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org; edubezval-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Jia Hongtao-B38951
> Subject: [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ
> T1040
>
> This is Thermal Monitoring Unit for QorIQ platform.
>
> Signed-off-by: Jia Hongtao <hongtao.jia-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
> ---
> Changes of V3:
> * Put TMU node directly into t1040si-post.dtsi file.
> * Add "fsl,tmu-range" property.
> * Change "calibration" property to "fsl,tmu-calibration".
> * Update the calibration data.
>
> Changes of V2:
> * Provide more details on compatible and calibration properties.
>
> .../devicetree/bindings/thermal/qoriq-thermal.txt | 63
> ++++++++++++++++++++++
> arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 42 +++++++++++++++
> 2 files changed, 105 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-
> thermal.txt
>
> diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
> b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
> new file mode 100644
> index 0000000..2bc9cb3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
> @@ -0,0 +1,63 @@
> +* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs
> +
> +Required properties:
> +- compatible : Must include "fsl,qoriq-tmu". The version of the device
> is
> + determined by the TMU IP Block Revision Register (IPBRR0) at
> + offset 0x0BF8.
> + Table of correspondences between IPBRR0 values and example chips:
> + Value Device
> + ---------- -----
> + 0x01900102 T1040
> +- reg : Address range of TMU registers.
> +- interrupts : Contains the interrupt for TMU.
> +- fsl,tmu-range : Temperature range for TMU. Including the starting
> + temperature and number of calibration points for each range.
> +- fsl,tmu-calibration : Calibration table for TMU. This is required to
> + determine what a specific sensor reading translates to in degrees
> + Celsius. There are four calibration ranges, for each range we need
> + a couple of calibration data formatted like <TTCFGR, TSCFGR>.
> + Freescale provides the data required.
> +
> +Example:
> +
> +tmu@f0000 {
> + compatible = "fsl,qoriq-tmu";
> + reg = <0xf0000 0x1000>;
> + interrupts = <18 2 0 0>;
> + fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
> + fsl,tmu-calibration = <0x00000000 0x00000025
> + 0x00000001 0x00000028
> + 0x00000002 0x0000002d
> + 0x00000003 0x00000031
> + 0x00000004 0x00000036
> + 0x00000005 0x0000003a
> + 0x00000006 0x00000040
> + 0x00000007 0x00000044
> + 0x00000008 0x0000004a
> + 0x00000009 0x0000004f
> + 0x0000000a 0x00000054
> +
> + 0x00010000 0x0000000d
> + 0x00010001 0x00000013
> + 0x00010002 0x00000019
> + 0x00010003 0x0000001f
> + 0x00010004 0x00000025
> + 0x00010005 0x0000002d
> + 0x00010006 0x00000033
> + 0x00010007 0x00000043
> + 0x00010008 0x0000004b
> + 0x00010009 0x00000053
> +
> + 0x00020000 0x00000010
> + 0x00020001 0x00000017
> + 0x00020002 0x0000001f
> + 0x00020003 0x00000029
> + 0x00020004 0x00000031
> + 0x00020005 0x0000003c
> + 0x00020006 0x00000042
> + 0x00020007 0x0000004d
> + 0x00020008 0x00000056
> +
> + 0x00030000 0x00000012
> + 0x00030001 0x0000001d>;
> +};
> diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> index 5cc01be..6d9ca4d 100644
> --- a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> +++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> @@ -407,6 +407,48 @@
> reg = <0xea000 0x4000>;
> };
>
> + tmu@f0000 {
> + compatible = "fsl,qoriq-tmu";
> + reg = <0xf0000 0x1000>;
> + interrupts = <18 2 0 0>;
> + fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
> + fsl,tmu-calibration = <0x00000000 0x00000025
> + 0x00000001 0x00000028
> + 0x00000002 0x0000002d
> + 0x00000003 0x00000031
> + 0x00000004 0x00000036
> + 0x00000005 0x0000003a
> + 0x00000006 0x00000040
> + 0x00000007 0x00000044
> + 0x00000008 0x0000004a
> + 0x00000009 0x0000004f
> + 0x0000000a 0x00000054
> +
> + 0x00010000 0x0000000d
> + 0x00010001 0x00000013
> + 0x00010002 0x00000019
> + 0x00010003 0x0000001f
> + 0x00010004 0x00000025
> + 0x00010005 0x0000002d
> + 0x00010006 0x00000033
> + 0x00010007 0x00000043
> + 0x00010008 0x0000004b
> + 0x00010009 0x00000053
> +
> + 0x00020000 0x00000010
> + 0x00020001 0x00000017
> + 0x00020002 0x0000001f
> + 0x00020003 0x00000029
> + 0x00020004 0x00000031
> + 0x00020005 0x0000003c
> + 0x00020006 0x00000042
> + 0x00020007 0x0000004d
> + 0x00020008 0x00000056
> +
> + 0x00030000 0x00000012
> + 0x00030001 0x0000001d>;
> + };
> +
> /include/ "elo3-dma-0.dtsi"
> /include/ "elo3-dma-1.dtsi"
> /include/ "qoriq-espi-0.dtsi"
> --
> 2.1.0.27.g96db324
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040
@ 2015-07-09 8:00 ` Hongtao Jia
0 siblings, 0 replies; 6+ messages in thread
From: Hongtao Jia @ 2015-07-09 8:00 UTC (permalink / raw)
To: Hongtao Jia, Scott Wood; +Cc: linuxppc-dev, devicetree, robh+dt, edubezval
Hi Scott,
Patch updated to V3, please help to review.
Thanks.
---
Best Regards,
Hongtao
> -----Original Message-----
> From: Jia Hongtao [mailto:hongtao.jia@freescale.com]
> Sent: Thursday, June 11, 2015 3:53 PM
> To: Wood Scott-B07421
> Cc: linuxppc-dev@lists.ozlabs.org; devicetree@vger.kernel.org;
> robh+dt@kernel.org; edubezval@gmail.com; Jia Hongtao-B38951
> Subject: [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ
> T1040
>=20
> This is Thermal Monitoring Unit for QorIQ platform.
>=20
> Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
> ---
> Changes of V3:
> * Put TMU node directly into t1040si-post.dtsi file.
> * Add "fsl,tmu-range" property.
> * Change "calibration" property to "fsl,tmu-calibration".
> * Update the calibration data.
>=20
> Changes of V2:
> * Provide more details on compatible and calibration properties.
>=20
> .../devicetree/bindings/thermal/qoriq-thermal.txt | 63
> ++++++++++++++++++++++
> arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 42 +++++++++++++++
> 2 files changed, 105 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/thermal/qoriq-
> thermal.txt
>=20
> diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
> b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
> new file mode 100644
> index 0000000..2bc9cb3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt
> @@ -0,0 +1,63 @@
> +* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs
> +
> +Required properties:
> +- compatible : Must include "fsl,qoriq-tmu". The version of the device
> is
> + determined by the TMU IP Block Revision Register (IPBRR0) at
> + offset 0x0BF8.
> + Table of correspondences between IPBRR0 values and example chips:
> + Value Device
> + ---------- -----
> + 0x01900102 T1040
> +- reg : Address range of TMU registers.
> +- interrupts : Contains the interrupt for TMU.
> +- fsl,tmu-range : Temperature range for TMU. Including the starting
> + temperature and number of calibration points for each range.
> +- fsl,tmu-calibration : Calibration table for TMU. This is required to
> + determine what a specific sensor reading translates to in degrees
> + Celsius. There are four calibration ranges, for each range we need
> + a couple of calibration data formatted like <TTCFGR, TSCFGR>.
> + Freescale provides the data required.
> +
> +Example:
> +
> +tmu@f0000 {
> + compatible =3D "fsl,qoriq-tmu";
> + reg =3D <0xf0000 0x1000>;
> + interrupts =3D <18 2 0 0>;
> + fsl,tmu-range =3D <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
> + fsl,tmu-calibration =3D <0x00000000 0x00000025
> + 0x00000001 0x00000028
> + 0x00000002 0x0000002d
> + 0x00000003 0x00000031
> + 0x00000004 0x00000036
> + 0x00000005 0x0000003a
> + 0x00000006 0x00000040
> + 0x00000007 0x00000044
> + 0x00000008 0x0000004a
> + 0x00000009 0x0000004f
> + 0x0000000a 0x00000054
> +
> + 0x00010000 0x0000000d
> + 0x00010001 0x00000013
> + 0x00010002 0x00000019
> + 0x00010003 0x0000001f
> + 0x00010004 0x00000025
> + 0x00010005 0x0000002d
> + 0x00010006 0x00000033
> + 0x00010007 0x00000043
> + 0x00010008 0x0000004b
> + 0x00010009 0x00000053
> +
> + 0x00020000 0x00000010
> + 0x00020001 0x00000017
> + 0x00020002 0x0000001f
> + 0x00020003 0x00000029
> + 0x00020004 0x00000031
> + 0x00020005 0x0000003c
> + 0x00020006 0x00000042
> + 0x00020007 0x0000004d
> + 0x00020008 0x00000056
> +
> + 0x00030000 0x00000012
> + 0x00030001 0x0000001d>;
> +};
> diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> index 5cc01be..6d9ca4d 100644
> --- a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> +++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> @@ -407,6 +407,48 @@
> reg =3D <0xea000 0x4000>;
> };
>=20
> + tmu@f0000 {
> + compatible =3D "fsl,qoriq-tmu";
> + reg =3D <0xf0000 0x1000>;
> + interrupts =3D <18 2 0 0>;
> + fsl,tmu-range =3D <0x000a0000 0x00090026 0x0008004a 0x0001006a>;
> + fsl,tmu-calibration =3D <0x00000000 0x00000025
> + 0x00000001 0x00000028
> + 0x00000002 0x0000002d
> + 0x00000003 0x00000031
> + 0x00000004 0x00000036
> + 0x00000005 0x0000003a
> + 0x00000006 0x00000040
> + 0x00000007 0x00000044
> + 0x00000008 0x0000004a
> + 0x00000009 0x0000004f
> + 0x0000000a 0x00000054
> +
> + 0x00010000 0x0000000d
> + 0x00010001 0x00000013
> + 0x00010002 0x00000019
> + 0x00010003 0x0000001f
> + 0x00010004 0x00000025
> + 0x00010005 0x0000002d
> + 0x00010006 0x00000033
> + 0x00010007 0x00000043
> + 0x00010008 0x0000004b
> + 0x00010009 0x00000053
> +
> + 0x00020000 0x00000010
> + 0x00020001 0x00000017
> + 0x00020002 0x0000001f
> + 0x00020003 0x00000029
> + 0x00020004 0x00000031
> + 0x00020005 0x0000003c
> + 0x00020006 0x00000042
> + 0x00020007 0x0000004d
> + 0x00020008 0x00000056
> +
> + 0x00030000 0x00000012
> + 0x00030001 0x0000001d>;
> + };
> +
> /include/ "elo3-dma-0.dtsi"
> /include/ "elo3-dma-1.dtsi"
> /include/ "qoriq-espi-0.dtsi"
> --
> 2.1.0.27.g96db324
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040
2015-07-09 8:00 ` Hongtao Jia
@ 2015-07-09 22:26 ` Scott Wood
-1 siblings, 0 replies; 6+ messages in thread
From: Scott Wood @ 2015-07-09 22:26 UTC (permalink / raw)
To: Jia Hongtao-B38951; +Cc: edubezval, devicetree, robh+dt, linuxppc-dev
On Thu, 2015-07-09 at 03:00 -0500, Jia Hongtao-B38951 wrote:
> Hi Scott,
>
> Patch updated to V3, please help to review.
> Thanks.
>
> ---
> Best Regards,
> Hongtao
It looks OK.
-Scott
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040
@ 2015-07-09 22:26 ` Scott Wood
0 siblings, 0 replies; 6+ messages in thread
From: Scott Wood @ 2015-07-09 22:26 UTC (permalink / raw)
To: Jia Hongtao-B38951; +Cc: linuxppc-dev, devicetree, robh+dt, edubezval
On Thu, 2015-07-09 at 03:00 -0500, Jia Hongtao-B38951 wrote:
> Hi Scott,
>
> Patch updated to V3, please help to review.
> Thanks.
>
> ---
> Best Regards,
> Hongtao
It looks OK.
-Scott
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2015-07-09 22:27 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-06-11 7:53 [PATCH V3] QorIQ/TMU: add TMU node to device tree for QorIQ T1040 Jia Hongtao
2015-06-11 7:53 ` Jia Hongtao
[not found] ` <1434009188-25644-1-git-send-email-hongtao.jia-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
2015-07-09 8:00 ` Hongtao Jia
2015-07-09 8:00 ` Hongtao Jia
2015-07-09 22:26 ` Scott Wood
2015-07-09 22:26 ` Scott Wood
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.