[PATCH v6] Add Mediatek thermal support

[PATCH v6] Add Mediatek thermal support

[Sascha Hauer]

This series adds support for the thermal sensors included in the
MT8173 SoC. Currently only basic temperature reading is supported
without any interrupt support.

The cpufreq driver for MT8173 is currently under review, so there's no
real cooling device available in mainline. Until this is available the
thermal driver can be tested with the following dts snippet. It creates
a fake gpio fan and a fake trip point which is so low that it can easily
be reached with a "cat /dev/zero > /dev/null" on the command line.

Please review and let me know what's missing to be included in mainline.

changes since v5:
- update copyright
- remove unused defines

Changes since v4:
- give calibration constants more meaningful names (offset, slope)
- Use define instead of 0x00c for register access.

Changes since v3:
- add include/dt-bindings/thermal/mt8173.h for to be able to use sensor names
  in dts files
- fix disabling wrong clock in error path
- remove now unused reset-names property from binding document
- rename MT8173_NUM_BANKS -> MT8173_NUM_ZONES
- rename MT8173_NUM_SENSING_POINTS -> MT8173_NUM_SENSORS_PER_ZONE
- rename struct thermal_zone_device *tz -> struct thermal_zone_device *tzd

Changes since v2:
- sort #includes alphabetically
- Add prefix to register defines
- drop some members from struct mtk_thermal
- simplify raw_to_mcelsius()
- add and use more register bit defines
- use device_reset() instead of devm_reset_control_get()/reset_control_reset()
- misc other stuff

Changes since v1:
- Use "mediatek," prefix for custom properties
- Drop "thermal: consistently use int for temperatures" dependency

Sascha

        fan: gpio_fan {
                compatible = "gpio-fan";
                gpios = <&pio 24 0>;
                gpio-fan,speed-map = <0    0
                                      4500 1>;
                #cooling-cells = <2>;
        };

        thermal-zones {
                cpu_thermal: cpu_thermal {
                        polling-delay-passive = <1000>; /* milliseconds */
                        polling-delay = <1000>; /* milliseconds */

                        thermal-sensors = <&thermal 0>;

                        trips {
                                cpu_passive: cpu_passive {
                                        temperature = <47000>; /* millicelsius */
                                        hysteresis = <2000>; /* millicelsius */
                                        type = "passive";
                                };

                                cpu_crit {
                                        temperature = <90000>; /* millicelsius */
                                        hysteresis = <2000>; /* millicelsius */
                                        type = "critical";
                                };
                        };

                        cooling-maps {
                                map0 {
                                        trip = <&cpu_passive>;
                                        cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
                                };
                        };
                };
        };

[PATCH 1/3] dt-bindings: thermal: Add binding document for Mediatek thermal controller

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
---
 .../bindings/thermal/mediatek-thermal.txt          | 38 ++++++++++++++++++++++
 include/dt-bindings/thermal/mt8173.h               | 13 ++++++++
 2 files changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
 create mode 100644 include/dt-bindings/thermal/mt8173.h

diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
new file mode 100644
index 0000000..1697375
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
@@ -0,0 +1,38 @@
+* Mediatek Thermal
+
+This describes the device tree binding for the Mediatek thermal controller
+which measures the on-SoC temperatures. This device does not have its own ADC,
+instead it directly controls the AUXADC via AHB bus accesses. For this reason
+this device needs phandles to the AUXADC. Also it controls a mux in the
+apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS
+is also needed.
+
+Required properties:
+- compatible: "mediatek,mt8173-thermal"
+- reg: Address range of the thermal controller
+- interrupts: IRQ for the thermal controller
+- clocks, clock-names: Clocks needed for the thermal controller. required
+                       clocks are:
+		       "therm":	 Main clock needed for register access
+		       "auxadc": The AUXADC clock
+- resets: Reference to the reset controller controlling the thermal controller.
+- mediatek,auxadc: A phandle to the AUXADC which the thermal controller uses
+- mediatek,apmixedsys: A phandle to the APMIXEDSYS controller.
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. See
+			  include/dt-bindings/thermal/mt8173.h for valid sensor
+			  numbers.
+
+Example:
+
+	thermal: thermal@1100b000 {
+		#thermal-sensor-cells = <1>;
+		compatible = "mediatek,mt8173-thermal";
+		reg = <0 0x1100b000 0 0x1000>;
+		interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
+		clock-names = "therm", "auxadc";
+		resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
+		reset-names = "therm";
+		mediatek,auxadc = <&auxadc>;
+		mediatek,apmixedsys = <&apmixedsys>;
+	};
diff --git a/include/dt-bindings/thermal/mt8173.h b/include/dt-bindings/thermal/mt8173.h
new file mode 100644
index 0000000..692e74c
--- /dev/null
+++ b/include/dt-bindings/thermal/mt8173.h
@@ -0,0 +1,13 @@
+/*
+ * This header provides constants for mediatek,mt8173-thermal
+ */
+
+#ifndef _DT_BINDINGS_THERMAL_MEDIATEK_MT8173_H
+#define _DT_BINDINGS_THERMAL_MEDIATEK_MT8173_H
+
+#define MT8173_THERMAL_ZONE_CA53	0
+#define MT8173_THERMAL_ZONE_CA57	1
+#define MT8173_THERMAL_ZONE_GPU		2
+#define MT8173_THERMAL_ZONE_CORE	3
+
+#endif /* _DT_BINDINGS_THERMAL_MEDIATEK_MT8173_H */
-- 
2.5.0

[PATCH 2/3] thermal: Add Mediatek thermal controller support

[Sascha Hauer]

This adds support for the Mediatek thermal controller found on MT8173
and likely other SoCs.
The controller is a bit special. It does not have its own ADC, instead
it controls the on-SoC AUXADC via AHB bus accesses. For this reason
we need the physical address of the AUXADC. Also it controls a mux
using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
---
 drivers/thermal/Kconfig       |   8 +
 drivers/thermal/Makefile      |   1 +
 drivers/thermal/mtk_thermal.c | 528 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 537 insertions(+)
 create mode 100644 drivers/thermal/mtk_thermal.c

diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 118938e..07ad114 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -340,6 +340,14 @@ config ACPI_THERMAL_REL
 	tristate
 	depends on ACPI
 
+config MTK_THERMAL
+	tristate "Temperature sensor driver for mediatek SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	default y
+	help
+	  Enable this option if you want to have support for thermal management
+	  controller present in Mediatek SoCs
+
 menu "Texas Instruments thermal drivers"
 source "drivers/thermal/ti-soc-thermal/Kconfig"
 endmenu
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 535dfee..cc1cab3 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -44,3 +44,4 @@ obj-$(CONFIG_INT340X_THERMAL)  += int340x_thermal/
 obj-$(CONFIG_ST_THERMAL)	+= st/
 obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
 obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
+obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
new file mode 100644
index 0000000..8029698
--- /dev/null
+++ b/drivers/thermal/mtk_thermal.c
@@ -0,0 +1,528 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Hanyi.Wu <hanyi.wu@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+#include <linux/reset.h>
+#include <linux/time.h>
+#include <linux/types.h>
+
+/* AUXADC Registers */
+#define AUXADC_CON0_V		0x000
+#define AUXADC_CON1_V		0x004
+#define AUXADC_CON1_SET_V	0x008
+#define AUXADC_CON1_CLR_V	0x00c
+#define AUXADC_CON2_V		0x010
+#define AUXADC_DATA(channel)	(0x14 + (channel) * 4)
+#define AUXADC_MISC_V		0x094
+
+#define AUXADC_CON1_CHANNEL(x)	BIT(x)
+
+#define APMIXED_SYS_TS_CON1	0x604
+
+/* Thermal Controller Registers */
+#define TEMP_MONCTL0		0x000
+#define TEMP_MONCTL1		0x004
+#define TEMP_MONCTL2		0x008
+#define TEMP_MSRCTL0		0x038
+#define TEMP_AHBPOLL		0x040
+#define TEMP_AHBTO		0x044
+#define TEMP_ADCPNP0		0x048
+#define TEMP_ADCPNP1		0x04c
+#define TEMP_ADCPNP2		0x050
+#define TEMP_ADCPNP3		0x0b4
+
+#define TEMP_ADCMUX		0x054
+#define TEMP_ADCEN		0x060
+#define TEMP_PNPMUXADDR		0x064
+#define TEMP_ADCMUXADDR		0x068
+#define TEMP_ADCENADDR		0x074
+#define TEMP_ADCVALIDADDR	0x078
+#define TEMP_ADCVOLTADDR	0x07c
+#define TEMP_RDCTRL		0x080
+#define TEMP_ADCVALIDMASK	0x084
+#define TEMP_ADCVOLTAGESHIFT	0x088
+#define TEMP_ADCWRITECTRL	0x08c
+#define TEMP_MSR0		0x090
+#define TEMP_MSR1		0x094
+#define TEMP_MSR2		0x098
+#define TEMP_MSR3		0x0B8
+
+#define TEMP_SPARE0		0x0f0
+
+#define PTPCORESEL		0x400
+
+#define TEMP_MONCTL1_PERIOD_UNIT(x)	((x) & 0x3ff)
+
+#define TEMP_MONCTL2_FILTER_INTERVAL(x)	(((x) & 0x3ff)) << 16
+#define TEMP_MONCTL2_SENSOR_INTERVAL(x)	((x) & 0x3ff)
+
+#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x)	(x)
+
+#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE		BIT(0)
+#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE		BIT(1)
+
+#define TEMP_ADCVALIDMASK_VALID_HIGH		BIT(5)
+#define TEMP_ADCVALIDMASK_VALID_POS(bit)	(bit)
+
+#define MT8173_TS1	0
+#define MT8173_TS2	1
+#define MT8173_TS3	2
+#define MT8173_TS4	3
+#define MT8173_TSABB	4
+
+/* AUXADC channel 11 is used for the temperature sensors */
+#define MT8173_TEMP_AUXADC_CHANNEL	11
+
+/* The total number of temperature sensors in the MT8173 */
+#define MT8173_NUM_SENSORS		5
+
+/* The number of banks in the MT8173 */
+#define MT8173_NUM_ZONES		4
+
+/* The number of sensing points per bank */
+#define MT8173_NUM_SENSORS_PER_ZONE	4
+
+#define THERMAL_NAME    "mtk-thermal"
+
+struct mtk_thermal;
+
+struct mtk_thermal_bank {
+	struct mtk_thermal *mt;
+	struct thermal_zone_device *tzd;
+	int id;
+};
+
+struct mtk_thermal {
+	struct device *dev;
+	void __iomem *thermal_base;
+
+	struct clk *clk_peri_therm;
+	struct clk *clk_auxadc;
+
+	struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
+
+	struct mutex lock;
+
+	/* Calibration values */
+	int calib_slope;
+	int calib_offset;
+};
+
+struct mtk_thermal_bank_cfg {
+	unsigned int num_sensors;
+	unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
+};
+
+static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
+
+/*
+ * The MT8173 thermal controller has four banks. Each bank can read up to
+ * four temperature sensors simultaneously. The MT8173 has a total of 5
+ * temperature sensors. We use each bank to measure a certain area of the
+ * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
+ * areas, hence is used in different banks.
+ */
+static const struct mtk_thermal_bank_cfg bank_data[] = {
+	{
+		.num_sensors = 2,
+		.sensors = { MT8173_TS2, MT8173_TS3 },
+	}, {
+		.num_sensors = 2,
+		.sensors = { MT8173_TS2, MT8173_TS4 },
+	}, {
+		.num_sensors = 3,
+		.sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
+	}, {
+		.num_sensors = 1,
+		.sensors = { MT8173_TS2 },
+	},
+};
+
+struct mtk_thermal_sense_point {
+	int msr;
+	int adcpnp;
+};
+
+static const struct mtk_thermal_sense_point
+		sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
+	{
+		.msr = TEMP_MSR0,
+		.adcpnp = TEMP_ADCPNP0,
+	}, {
+		.msr = TEMP_MSR1,
+		.adcpnp = TEMP_ADCPNP1,
+	}, {
+		.msr = TEMP_MSR2,
+		.adcpnp = TEMP_ADCPNP2,
+	}, {
+		.msr = TEMP_MSR3,
+		.adcpnp = TEMP_ADCPNP3,
+	},
+};
+
+/**
+ * raw_to_mcelsius - convert a raw ADC value to mcelsius
+ * @mt:		The thermal controller
+ * @raw:	raw ADC value
+ *
+ * This converts the raw ADC value to mcelsius using the SoC specific
+ * calibration constants
+ */
+static int raw_to_mcelsius(struct mtk_thermal *mt, u32 raw)
+{
+	return mt->calib_offset + mt->calib_slope * (raw & 0xfff);
+}
+
+/**
+ * mtk_thermal_get_bank - get bank
+ * @bank:	The bank
+ *
+ * The bank registers are banked, we have to select a bank in the
+ * PTPCORESEL register to access it.
+ */
+static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+	u32 val;
+
+	mutex_lock(&mt->lock);
+
+	val = readl(mt->thermal_base + PTPCORESEL);
+	val &= ~0xf;
+	val |= bank->id;
+	writel(val, mt->thermal_base + PTPCORESEL);
+}
+
+/**
+ * mtk_thermal_put_bank - release bank
+ * @bank:	The bank
+ *
+ * release a bank previously taken with mtk_thermal_get_bank,
+ */
+static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+
+	mutex_unlock(&mt->lock);
+}
+
+/**
+ * mtk_thermal_bank_temperature - get the temperature of a bank
+ * @bank:	The bank
+ *
+ * The temperature of a bank is considered the maximum temperature of
+ * the sensors associated to the bank.
+ */
+static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+	int temp, i, max;
+	u32 raw;
+
+	temp = max = INT_MIN;
+
+	for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
+		raw = readl(mt->thermal_base + sensing_points[i].msr);
+
+		temp = raw_to_mcelsius(mt, raw);
+
+		/*
+		 * The first read of a sensor often contains very high bogus
+		 * temperature value. Filter these out so that the system does
+		 * not immediately shut down.
+		 */
+		if (temp > 200000)
+			temp = 0;
+
+		if (temp > max)
+			max = temp;
+	}
+
+	return max;
+}
+
+static int mtk_read_temp(void *data, long *temp)
+{
+	struct mtk_thermal_bank *bank = data;
+
+	mtk_thermal_get_bank(bank);
+
+	*temp = mtk_thermal_bank_temperature(bank);
+
+	mtk_thermal_put_bank(bank);
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
+	.get_temp = mtk_read_temp,
+};
+
+static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
+		u32 apmixed_phys_base, u32 auxadc_phys_base)
+{
+	struct mtk_thermal_bank *bank = &mt->banks[num];
+	const struct mtk_thermal_bank_cfg *cfg = &bank_data[num];
+	int i;
+
+	bank->id = num;
+	bank->mt = mt;
+
+	mtk_thermal_get_bank(bank);
+
+	/* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
+	writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1);
+
+	/*
+	 * filt interval is 1 * 46.540us = 46.54us,
+	 * sen interval is 429 * 46.540us = 19.96ms
+	 */
+	writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
+			TEMP_MONCTL2_SENSOR_INTERVAL(429),
+			mt->thermal_base + TEMP_MONCTL2);
+
+	/* poll is set to 10u */
+	writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
+			mt->thermal_base + TEMP_AHBPOLL);
+
+	/* temperature sampling control, 1 sample */
+	writel(0x00000000, mt->thermal_base + TEMP_MSRCTL0);
+
+	/* exceed this polling time, IRQ would be inserted */
+	writel(0xffffffff, mt->thermal_base + TEMP_AHBTO);
+
+	/* number of interrupts per event, 1 is enough */
+	writel(0x0, mt->thermal_base + TEMP_MONIDET0);
+	writel(0x0, mt->thermal_base + TEMP_MONIDET1);
+
+	/*
+	 * The MT8173 thermal controller does not have its own ADC. Instead it
+	 * uses AHB bus accesses to control the AUXADC. To do this the thermal
+	 * controller has to be programmed with the physical addresses of the
+	 * AUXADC registers and with the various bit positions in the AUXADC.
+	 * Also the thermal controller controls a mux in the APMIXEDSYS register
+	 * space.
+	 */
+
+	/*
+	 * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
+	 * automatically by hw
+	 */
+	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCMUX);
+
+	/* AHB address for auxadc mux selection */
+	writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
+			mt->thermal_base + TEMP_ADCMUXADDR);
+
+	/* AHB address for pnp sensor mux selection */
+	writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
+			mt->thermal_base + TEMP_PNPMUXADDR);
+
+	/* AHB value for auxadc enable */
+	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCEN);
+
+	/* AHB address for auxadc enable (channel 0 immediate mode selected) */
+	writel(auxadc_phys_base + AUXADC_CON1_SET_V,
+			mt->thermal_base + TEMP_ADCENADDR);
+
+	/* AHB address for auxadc valid bit */
+	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+			mt->thermal_base + TEMP_ADCVALIDADDR);
+
+	/* AHB address for auxadc voltage output */
+	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+			mt->thermal_base + TEMP_ADCVOLTADDR);
+
+	/* read valid & voltage are at the same register */
+	writel(0x0, mt->thermal_base + TEMP_RDCTRL);
+
+	/* indicate where the valid bit is */
+	writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12),
+			mt->thermal_base + TEMP_ADCVALIDMASK);
+
+	/* no shift */
+	writel(0x0, mt->thermal_base + TEMP_ADCVOLTAGESHIFT);
+
+	/* enable auxadc mux write transaction */
+	writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
+			mt->thermal_base + TEMP_ADCWRITECTRL);
+
+	for (i = 0; i < cfg->num_sensors; i++)
+		writel(sensor_mux_values[cfg->sensors[i]],
+				mt->thermal_base + sensing_points[i].adcpnp);
+
+	writel((1 << cfg->num_sensors) - 1, mt->thermal_base + TEMP_MONCTL0);
+
+	writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE | TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
+			mt->thermal_base + TEMP_ADCWRITECTRL);
+
+	mtk_thermal_put_bank(bank);
+}
+
+static u64 of_get_phys_base(struct device_node *np)
+{
+	u64 size64;
+	const __be32 *regaddr_p;
+
+	regaddr_p = of_get_address(np, 0, &size64, NULL);
+	if (!regaddr_p)
+		return OF_BAD_ADDR;
+
+	return of_translate_address(np, regaddr_p);
+}
+
+static int mtk_thermal_probe(struct platform_device *pdev)
+{
+	int ret, i;
+	struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
+	struct mtk_thermal *mt;
+	struct resource *res;
+	u64 auxadc_phys_base, apmixed_phys_base;
+
+	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
+	if (!mt)
+		return -ENOMEM;
+
+	mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm");
+	if (IS_ERR(mt->clk_peri_therm))
+		return PTR_ERR(mt->clk_peri_therm);
+
+	mt->clk_auxadc = devm_clk_get(&pdev->dev, "auxadc");
+	if (IS_ERR(mt->clk_auxadc))
+		return PTR_ERR(mt->clk_auxadc);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mt->thermal_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mt->thermal_base))
+		return PTR_ERR(mt->thermal_base);
+
+	mutex_init(&mt->lock);
+
+	mt->dev = &pdev->dev;
+
+	auxadc = of_parse_phandle(np, "mediatek,auxadc", 0);
+	if (!auxadc) {
+		dev_err(&pdev->dev, "missing auxadc node\n");
+		return -ENODEV;
+	}
+
+	auxadc_phys_base = of_get_phys_base(auxadc);
+	if (auxadc_phys_base == OF_BAD_ADDR) {
+		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
+		return -EINVAL;
+	}
+
+	apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0);
+	if (!apmixedsys) {
+		dev_err(&pdev->dev, "missing apmixedsys node\n");
+		return -ENODEV;
+	}
+
+	apmixed_phys_base = of_get_phys_base(apmixedsys);
+	if (apmixed_phys_base == OF_BAD_ADDR) {
+		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
+		return -EINVAL;
+	}
+
+	ret = clk_prepare_enable(mt->clk_auxadc);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
+		return ret;
+	}
+
+	ret = device_reset(&pdev->dev);
+	if (ret)
+		goto err_disable_clk_auxadc;
+
+	ret = clk_prepare_enable(mt->clk_peri_therm);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
+		goto err_disable_clk_auxadc;
+	}
+
+	/*
+	 * These calibration values should finally be provided by the
+	 * firmware or fuses. For now use default values.
+	 */
+	mt->calib_slope = -123;
+	mt->calib_offset = 465124;
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++)
+		mtk_thermal_init_bank(mt, i, apmixed_phys_base, auxadc_phys_base);
+
+	platform_set_drvdata(pdev, mt);
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++) {
+		struct mtk_thermal_bank *bank = &mt->banks[i];
+
+		bank->tzd = thermal_zone_of_sensor_register(&pdev->dev, i, bank,
+				&mtk_thermal_ops);
+	}
+
+	return 0;
+
+err_disable_clk_auxadc:
+	clk_disable_unprepare(mt->clk_auxadc);
+
+	return ret;
+}
+
+static int mtk_thermal_remove(struct platform_device *pdev)
+{
+	struct mtk_thermal *mt = platform_get_drvdata(pdev);
+	int i;
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++) {
+		struct mtk_thermal_bank *bank = &mt->banks[i];
+
+		thermal_zone_of_sensor_unregister(&pdev->dev, bank->tzd);
+	}
+
+	clk_disable_unprepare(mt->clk_peri_therm);
+	clk_disable_unprepare(mt->clk_auxadc);
+
+	return 0;
+}
+
+static const struct of_device_id mtk_thermal_of_match[] = {
+	{
+		.compatible = "mediatek,mt8173-thermal",
+	}, {
+	},
+};
+
+static struct platform_driver mtk_thermal_driver = {
+	.probe = mtk_thermal_probe,
+	.remove = mtk_thermal_remove,
+	.driver = {
+		.name = THERMAL_NAME,
+		.of_match_table = mtk_thermal_of_match,
+	},
+};
+
+module_platform_driver(mtk_thermal_driver);
+
+MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de");
+MODULE_DESCRIPTION("Mediatek thermal driver");
+MODULE_LICENSE("GPL v2");
-- 
2.5.0

[PATCH 3/3] ARM64: dts: mt8173: Add thermal/auxadc device nodes

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
---
 arch/arm64/boot/dts/mediatek/mt8173.dtsi | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index 27237a1..ddacb86 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -151,6 +151,11 @@
 				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		auxadc: auxadc@11001000 {
+			compatible = "mediatek,mt8173-auxadc";
+			reg = <0 0x11001000 0 0x1000>;
+		};
+
 		uart0: serial@11002000 {
 			compatible = "mediatek,mt8173-uart",
 				     "mediatek,mt6577-uart";
@@ -186,6 +191,18 @@
 			clocks = <&uart_clk>;
 			status = "disabled";
 		};
+
+		thermal: thermal@1100b000 {
+			#thermal-sensor-cells = <1>;
+			compatible = "mediatek,mt8173-thermal";
+			reg = <0 0x1100b000 0 0x1000>;
+			interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
+			clock-names = "therm", "auxadc";
+			resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
+			mediatek,auxadc = <&auxadc>;
+			mediatek,apmixedsys = <&apmixedsys>;
+		};
 	};
 };
 
-- 
2.5.0