[PATCH v8 0/5] Mediatek xHCI support

[PATCH v8 0/5] Mediatek xHCI support

[Chunfeng Yun]

>From e731877598e7564171bea62955b4e50b04d88d34 Mon Sep 17 00:00:00 2001
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
Date: Wed, 16 Sep 2015 14:24:11 +0800
Subject: [PATCH v8 0/5] Mediatek xHCI support

The patch supports MediaTek's xHCI controller.

There are some differences from xHCI spec:
1. The interval is specified in 250 * 8ns increments for Interrupt Moderation
Interval(IMODI) of the Interrupter Moderation(IMOD) register, it is 8 times as
much as that defined in xHCI spec.

2. For the value of TD Size in Normal TRB, MTK's xHCI controller defines a
number of packets that remain to be transferred for a TD after processing all
Max packets in all previous TRBs,that means don't include the current TRB's,
but in xHCI spec it includes the current ones.

3. To minimize the scheduling effort for synchronous endpoints in xHC, the MTK
architecture defines some extra SW scheduling parameters for HW. According to
these parameters provided by SW, the xHC can easily decide whether a
synchronous endpoint should be scheduled in a specific uFrame. The extra SW
scheduling parameters are put into reserved DWs in Slot and Endpoint Context.
And a bandwidth scheduler algorithm is added to support such feature.

A usb3.0 phy driver is also added which used by mt65xx SoCs platform, it
supports two usb2.0 ports and one usb3.0 port.

depend on the patch for TDS calculation:
https://patchwork.kernel.org/patch/7140041/

Change in v8:
1. use struct overlay for ippc register
2. change usb wakeup as optional feature
3. add TDS quirk into unified TDS calculation function

Change in v7:
1. remove xHCI timing setting which only for FPGA
2. revise xHCI scheduler algorithms
3. replace "usb" by "USB" in xHCI binding file

Change in v6:
1. get register base address of port in probe instead of of_xlate
2. enable clock in phy_init instead of probe

Change in v5:
1. descripte more exactly for each specifiers in xHCI binding
2. make use of new multi-phy feature for phy driver

Change in v4:
1. descripte more exactly for each specifiers in binding file
2. use BIT() to define a bit mask mcro

Change in v3:
1. implement generic phy
2. move opperations for IPPC and wakeup from phy driver to xHCI driver
3. seperate quirk functions into a single C file to fix up dependence issue

Change in v2:
1. Rebase to 4.2-rc1
2. Remove probe phy before add usb_hcd patch from this series due to 4.2-rc1
   already fix this issue
3. add xhci mac clocks
4. add suspend/resume
5. support remote wakeup


Chunfeng Yun (5):
  dt-bindings: Add usb3.0 phy binding for MT65xx SoCs
  dt-bindings: Add a binding for Mediatek xHCI host controller
  usb: phy: add usb3.0 phy driver for mt65xx SoCs
  xhci: mediatek: support MTK xHCI host controller
  arm64: dts: mediatek: add xHCI & usb phy for mt8173

 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     |  68 ++
 .../devicetree/bindings/usb/mt8173-xhci.txt        |  52 ++
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts        |  16 +
 arch/arm64/boot/dts/mediatek/mt8173.dtsi           |  43 ++
 drivers/phy/Kconfig                                |   9 +
 drivers/phy/Makefile                               |   1 +
 drivers/phy/phy-mt65xx-usb3.c                      | 456 +++++++++++++
 drivers/usb/host/Kconfig                           |   9 +
 drivers/usb/host/Makefile                          |   4 +
 drivers/usb/host/xhci-mtk-sch.c                    | 419 ++++++++++++
 drivers/usb/host/xhci-mtk.c                        | 744 +++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h                        | 156 +++++
 drivers/usb/host/xhci-ring.c                       |  22 +-
 drivers/usb/host/xhci.c                            |  19 +-
 drivers/usb/host/xhci.h                            |   1 +
 15 files changed, 2012 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

--
1.8.1.1.dirty

[PATCH v8 0/5] Mediatek xHCI support

[Chunfeng Yun]

>From e731877598e7564171bea62955b4e50b04d88d34 Mon Sep 17 00:00:00 2001
From: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
Date: Wed, 16 Sep 2015 14:24:11 +0800
Subject: [PATCH v8 0/5] Mediatek xHCI support

The patch supports MediaTek's xHCI controller.

There are some differences from xHCI spec:
1. The interval is specified in 250 * 8ns increments for Interrupt Moderation
Interval(IMODI) of the Interrupter Moderation(IMOD) register, it is 8 times as
much as that defined in xHCI spec.

2. For the value of TD Size in Normal TRB, MTK's xHCI controller defines a
number of packets that remain to be transferred for a TD after processing all
Max packets in all previous TRBs,that means don't include the current TRB's,
but in xHCI spec it includes the current ones.

3. To minimize the scheduling effort for synchronous endpoints in xHC, the MTK
architecture defines some extra SW scheduling parameters for HW. According to
these parameters provided by SW, the xHC can easily decide whether a
synchronous endpoint should be scheduled in a specific uFrame. The extra SW
scheduling parameters are put into reserved DWs in Slot and Endpoint Context.
And a bandwidth scheduler algorithm is added to support such feature.

A usb3.0 phy driver is also added which used by mt65xx SoCs platform, it
supports two usb2.0 ports and one usb3.0 port.

depend on the patch for TDS calculation:
https://patchwork.kernel.org/patch/7140041/

Change in v8:
1. use struct overlay for ippc register
2. change usb wakeup as optional feature
3. add TDS quirk into unified TDS calculation function

Change in v7:
1. remove xHCI timing setting which only for FPGA
2. revise xHCI scheduler algorithms
3. replace "usb" by "USB" in xHCI binding file

Change in v6:
1. get register base address of port in probe instead of of_xlate
2. enable clock in phy_init instead of probe

Change in v5:
1. descripte more exactly for each specifiers in xHCI binding
2. make use of new multi-phy feature for phy driver

Change in v4:
1. descripte more exactly for each specifiers in binding file
2. use BIT() to define a bit mask mcro

Change in v3:
1. implement generic phy
2. move opperations for IPPC and wakeup from phy driver to xHCI driver
3. seperate quirk functions into a single C file to fix up dependence issue

Change in v2:
1. Rebase to 4.2-rc1
2. Remove probe phy before add usb_hcd patch from this series due to 4.2-rc1
   already fix this issue
3. add xhci mac clocks
4. add suspend/resume
5. support remote wakeup


Chunfeng Yun (5):
  dt-bindings: Add usb3.0 phy binding for MT65xx SoCs
  dt-bindings: Add a binding for Mediatek xHCI host controller
  usb: phy: add usb3.0 phy driver for mt65xx SoCs
  xhci: mediatek: support MTK xHCI host controller
  arm64: dts: mediatek: add xHCI & usb phy for mt8173

 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     |  68 ++
 .../devicetree/bindings/usb/mt8173-xhci.txt        |  52 ++
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts        |  16 +
 arch/arm64/boot/dts/mediatek/mt8173.dtsi           |  43 ++
 drivers/phy/Kconfig                                |   9 +
 drivers/phy/Makefile                               |   1 +
 drivers/phy/phy-mt65xx-usb3.c                      | 456 +++++++++++++
 drivers/usb/host/Kconfig                           |   9 +
 drivers/usb/host/Makefile                          |   4 +
 drivers/usb/host/xhci-mtk-sch.c                    | 419 ++++++++++++
 drivers/usb/host/xhci-mtk.c                        | 744 +++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h                        | 156 +++++
 drivers/usb/host/xhci-ring.c                       |  22 +-
 drivers/usb/host/xhci.c                            |  19 +-
 drivers/usb/host/xhci.h                            |   1 +
 15 files changed, 2012 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

--
1.8.1.1.dirty

[PATCH v8 0/5] Mediatek xHCI support

[Chunfeng Yun]

>From e731877598e7564171bea62955b4e50b04d88d34 Mon Sep 17 00:00:00 2001
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
Date: Wed, 16 Sep 2015 14:24:11 +0800
Subject: [PATCH v8 0/5] Mediatek xHCI support

The patch supports MediaTek's xHCI controller.

There are some differences from xHCI spec:
1. The interval is specified in 250 * 8ns increments for Interrupt Moderation
Interval(IMODI) of the Interrupter Moderation(IMOD) register, it is 8 times as
much as that defined in xHCI spec.

2. For the value of TD Size in Normal TRB, MTK's xHCI controller defines a
number of packets that remain to be transferred for a TD after processing all
Max packets in all previous TRBs,that means don't include the current TRB's,
but in xHCI spec it includes the current ones.

3. To minimize the scheduling effort for synchronous endpoints in xHC, the MTK
architecture defines some extra SW scheduling parameters for HW. According to
these parameters provided by SW, the xHC can easily decide whether a
synchronous endpoint should be scheduled in a specific uFrame. The extra SW
scheduling parameters are put into reserved DWs in Slot and Endpoint Context.
And a bandwidth scheduler algorithm is added to support such feature.

A usb3.0 phy driver is also added which used by mt65xx SoCs platform, it
supports two usb2.0 ports and one usb3.0 port.

depend on the patch for TDS calculation:
https://patchwork.kernel.org/patch/7140041/

Change in v8:
1. use struct overlay for ippc register
2. change usb wakeup as optional feature
3. add TDS quirk into unified TDS calculation function

Change in v7:
1. remove xHCI timing setting which only for FPGA
2. revise xHCI scheduler algorithms
3. replace "usb" by "USB" in xHCI binding file

Change in v6:
1. get register base address of port in probe instead of of_xlate
2. enable clock in phy_init instead of probe

Change in v5:
1. descripte more exactly for each specifiers in xHCI binding
2. make use of new multi-phy feature for phy driver

Change in v4:
1. descripte more exactly for each specifiers in binding file
2. use BIT() to define a bit mask mcro

Change in v3:
1. implement generic phy
2. move opperations for IPPC and wakeup from phy driver to xHCI driver
3. seperate quirk functions into a single C file to fix up dependence issue

Change in v2:
1. Rebase to 4.2-rc1
2. Remove probe phy before add usb_hcd patch from this series due to 4.2-rc1
   already fix this issue
3. add xhci mac clocks
4. add suspend/resume
5. support remote wakeup


Chunfeng Yun (5):
  dt-bindings: Add usb3.0 phy binding for MT65xx SoCs
  dt-bindings: Add a binding for Mediatek xHCI host controller
  usb: phy: add usb3.0 phy driver for mt65xx SoCs
  xhci: mediatek: support MTK xHCI host controller
  arm64: dts: mediatek: add xHCI & usb phy for mt8173

 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     |  68 ++
 .../devicetree/bindings/usb/mt8173-xhci.txt        |  52 ++
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts        |  16 +
 arch/arm64/boot/dts/mediatek/mt8173.dtsi           |  43 ++
 drivers/phy/Kconfig                                |   9 +
 drivers/phy/Makefile                               |   1 +
 drivers/phy/phy-mt65xx-usb3.c                      | 456 +++++++++++++
 drivers/usb/host/Kconfig                           |   9 +
 drivers/usb/host/Makefile                          |   4 +
 drivers/usb/host/xhci-mtk-sch.c                    | 419 ++++++++++++
 drivers/usb/host/xhci-mtk.c                        | 744 +++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h                        | 156 +++++
 drivers/usb/host/xhci-ring.c                       |  22 +-
 drivers/usb/host/xhci.c                            |  19 +-
 drivers/usb/host/xhci.h                            |   1 +
 15 files changed, 2012 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

--
1.8.1.1.dirty

[PATCH v8 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

[Chunfeng Yun]

add a DT binding documentation of usb3.0 phy for MT65xx
SoCs from Mediatek.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 68 ++++++++++++++++++++++
 1 file changed, 68 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
new file mode 100644
index 0000000..00100cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
@@ -0,0 +1,68 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy@11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port@11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port@11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb@11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
-- 
1.8.1.1.dirty

[PATCH v8 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

[Chunfeng Yun]

add a DT binding documentation of usb3.0 phy for MT65xx
SoCs from Mediatek.

Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 68 ++++++++++++++++++++++
 1 file changed, 68 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
new file mode 100644
index 0000000..00100cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
@@ -0,0 +1,68 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy@11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port@11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port@11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb@11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
-- 
1.8.1.1.dirty

[PATCH v8 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

[Chunfeng Yun]

add a DT binding documentation of usb3.0 phy for MT65xx
SoCs from Mediatek.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 68 ++++++++++++++++++++++
 1 file changed, 68 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
new file mode 100644
index 0000000..00100cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
@@ -0,0 +1,68 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy at 11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port at 11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port at 11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb at 11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};
-- 
1.8.1.1.dirty

[PATCH v8 2/5] dt-bindings: Add a binding for Mediatek xHCI host controller

[Chunfeng Yun]

add a DT binding documentation of xHCI host controller for the
MT8173 SoC from Mediatek.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt

diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
new file mode 100644
index 0000000..0c96273
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
@@ -0,0 +1,52 @@
+MT8173 xHCI
+
+The device node for Mediatek SOC USB3.0 host controller
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers,
+	the first one for MAC, the second for IPPC
+ - interrupts : interrupt used by the controller
+ - power-domains : a phandle to USB power domain node to control USB's
+	mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+	entry in clock-names
+ - clock-names : must contain
+	"sys_ck": for clock of xHCI MAC
+	"wakeup_deb_p0": for USB wakeup debounce clock of port0
+	"wakeup_deb_p0": for USB wakeup debounce clock of port1
+
+ - phys : a list of phandle + phy specifier pairs
+ - usb3-lpm-capable : supports USB3.0 LPM
+
+Optional properties:
+ - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
+	mode;
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+	control register, it depends on "mediatek,wakeup-src".
+ - vbus-supply : reference to the VBUS regulator;
+
+Example:
+usb30: usb@11270000 {
+	compatible = "mediatek,mt8173-xhci";
+	reg = <0 0x11270000 0 0x1000>,
+	      <0 0x11280700 0 0x0100>;
+	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>,
+		 <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB1>;
+	clock-names = "sys_ck",
+		      "wakeup_deb_p0",
+		      "wakeup_deb_p1";
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	usb3-lpm-capable;
+	mediatek,syscon-wakeup = <&pericfg>;
+	mediatek,wakeup-src = <1>;
+	status = "okay";
+};
-- 
1.8.1.1.dirty

[PATCH v8 2/5] dt-bindings: Add a binding for Mediatek xHCI host controller

[Chunfeng Yun]

add a DT binding documentation of xHCI host controller for the
MT8173 SoC from Mediatek.

Signed-off-by: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
 .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt

diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
new file mode 100644
index 0000000..0c96273
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
@@ -0,0 +1,52 @@
+MT8173 xHCI
+
+The device node for Mediatek SOC USB3.0 host controller
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers,
+	the first one for MAC, the second for IPPC
+ - interrupts : interrupt used by the controller
+ - power-domains : a phandle to USB power domain node to control USB's
+	mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+	entry in clock-names
+ - clock-names : must contain
+	"sys_ck": for clock of xHCI MAC
+	"wakeup_deb_p0": for USB wakeup debounce clock of port0
+	"wakeup_deb_p0": for USB wakeup debounce clock of port1
+
+ - phys : a list of phandle + phy specifier pairs
+ - usb3-lpm-capable : supports USB3.0 LPM
+
+Optional properties:
+ - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
+	mode;
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+	control register, it depends on "mediatek,wakeup-src".
+ - vbus-supply : reference to the VBUS regulator;
+
+Example:
+usb30: usb@11270000 {
+	compatible = "mediatek,mt8173-xhci";
+	reg = <0 0x11270000 0 0x1000>,
+	      <0 0x11280700 0 0x0100>;
+	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>,
+		 <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB1>;
+	clock-names = "sys_ck",
+		      "wakeup_deb_p0",
+		      "wakeup_deb_p1";
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	usb3-lpm-capable;
+	mediatek,syscon-wakeup = <&pericfg>;
+	mediatek,wakeup-src = <1>;
+	status = "okay";
+};
-- 
1.8.1.1.dirty

[PATCH v8 2/5] dt-bindings: Add a binding for Mediatek xHCI host controller

[Chunfeng Yun]

add a DT binding documentation of xHCI host controller for the
MT8173 SoC from Mediatek.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt

diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
new file mode 100644
index 0000000..0c96273
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
@@ -0,0 +1,52 @@
+MT8173 xHCI
+
+The device node for Mediatek SOC USB3.0 host controller
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers,
+	the first one for MAC, the second for IPPC
+ - interrupts : interrupt used by the controller
+ - power-domains : a phandle to USB power domain node to control USB's
+	mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+	entry in clock-names
+ - clock-names : must contain
+	"sys_ck": for clock of xHCI MAC
+	"wakeup_deb_p0": for USB wakeup debounce clock of port0
+	"wakeup_deb_p0": for USB wakeup debounce clock of port1
+
+ - phys : a list of phandle + phy specifier pairs
+ - usb3-lpm-capable : supports USB3.0 LPM
+
+Optional properties:
+ - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
+	mode;
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+	control register, it depends on "mediatek,wakeup-src".
+ - vbus-supply : reference to the VBUS regulator;
+
+Example:
+usb30: usb at 11270000 {
+	compatible = "mediatek,mt8173-xhci";
+	reg = <0 0x11270000 0 0x1000>,
+	      <0 0x11280700 0 0x0100>;
+	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>,
+		 <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB1>;
+	clock-names = "sys_ck",
+		      "wakeup_deb_p0",
+		      "wakeup_deb_p1";
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	usb3-lpm-capable;
+	mediatek,syscon-wakeup = <&pericfg>;
+	mediatek,wakeup-src = <1>;
+	status = "okay";
+};
-- 
1.8.1.1.dirty

[PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Chunfeng Yun]

support usb3.0 phy of mt65xx SoCs

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/phy/Kconfig           |   9 +
 drivers/phy/Makefile          |   1 +
 drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 466 insertions(+)
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 47da573..ec436c1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a5b18c1..a7cc629 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
new file mode 100644
index 0000000..1f00b05
--- /dev/null
+++ b/drivers/phy/phy-mt65xx-usb3.c
@@ -0,0 +1,456 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+/*
+ * for sifslv2 register, but exclude port's;
+ * relative to USB3_SIF2_BASE base address
+ */
+#define SSUSB_SIFSLV_SPLLC		0x0000
+
+/* offsets of sub-segment in each port registers */
+#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
+#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
+#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
+#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
+
+#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
+#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
+
+#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
+#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
+
+#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
+#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
+#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
+#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
+
+#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
+#define PA6_RG_U2_ISO_EN		BIT(31)
+#define PA6_RG_U2_BC11_SW_EN		BIT(23)
+#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
+
+#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
+#define P2C_RG_USB20_GPIO_CTL		BIT(9)
+#define P2C_USB20_GPIO_MODE		BIT(8)
+#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
+
+#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
+#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
+
+#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
+#define P2C_FORCE_UART_EN		BIT(26)
+#define P2C_FORCE_DATAIN		BIT(23)
+#define P2C_FORCE_DM_PULLDOWN		BIT(21)
+#define P2C_FORCE_DP_PULLDOWN		BIT(20)
+#define P2C_FORCE_XCVRSEL		BIT(19)
+#define P2C_FORCE_SUSPENDM		BIT(18)
+#define P2C_FORCE_TERMSEL		BIT(17)
+#define P2C_RG_DATAIN			GENMASK(13, 10)
+#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
+#define P2C_RG_DMPULLDOWN		BIT(7)
+#define P2C_RG_DPPULLDOWN		BIT(6)
+#define P2C_RG_XCVRSEL			GENMASK(5, 4)
+#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
+#define P2C_RG_SUSPENDM			BIT(3)
+#define P2C_RG_TERMSEL			BIT(2)
+#define P2C_DTM0_PART_MASK \
+		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
+		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
+		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
+		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
+
+#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
+#define P2C_RG_UART_EN			BIT(16)
+#define P2C_RG_VBUSVALID		BIT(5)
+#define P2C_RG_SESSEND			BIT(4)
+#define P2C_RG_AVALID			BIT(2)
+
+#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
+#define P3A_RG_U3_VUSB10_ON		BIT(5)
+
+#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
+#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
+#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
+
+#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
+#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
+#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
+
+#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
+#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
+#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
+
+#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
+#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
+#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
+#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
+#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
+
+#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
+#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
+#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
+
+struct mt65xx_phy_instance {
+	struct phy *phy;
+	void __iomem *port_base;
+	u32 index;
+	u8 type;
+};
+
+struct mt65xx_u3phy {
+	struct device *dev;
+	void __iomem *sif_base;	/* include sif2, but exclude port's */
+	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
+	struct mt65xx_phy_instance **phys;
+	int nphys;
+};
+
+static void phy_instance_init(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	/* switch to USB function. (system register, force ip into usb mode) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_FORCE_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~P2C_RG_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U2PHYACR4);
+		tmp &= ~P2C_U2_GPIO_CTR_MSK;
+		writel(tmp, port_base + U3P_U2PHYACR4);
+	}
+
+	/* DP/DM BC1.1 path Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_BC11_SW_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
+	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
+	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
+	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG9);
+	tmp &= ~P3A_RG_RX_DAC_MUX;
+	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
+	writel(tmp, port_base + U3P_U3_PHYA_REG9);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG6);
+	tmp &= ~P3A_RG_TX_EIDLE_CM;
+	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
+	writel(tmp, port_base + U3P_U3_PHYA_REG6);
+
+	tmp = readl(port_base + U3P_PHYD_CDR1);
+	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
+	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
+	writel(tmp, port_base + U3P_PHYD_CDR1);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	if (!index) {
+		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp |= P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
+	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Enable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	if (!index) {
+		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
+		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
+		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
+		/* [mt8173]disable Change 100uA current from SSUSB */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
+	tmp &= ~P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+	/* USB 2.0 slew rate calibration */
+	tmp = readl(port_base + U3P_USBPHYACR5);
+	tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
+	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(4);
+	writel(tmp, port_base + U3P_USBPHYACR5);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
+	tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
+	tmp |= P2C_FORCE_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+	if (!index) {
+		/* (also disable)Change 100uA current switch to USB2.0 */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	/* let suspendm=0, set utmi into analog power down */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_RG_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+	udelay(1);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
+	tmp |= P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static int mt65xx_phy_init(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	ret = clk_prepare_enable(u3phy->u3phya_ref);
+	if (ret) {
+		dev_err(u3phy->dev, "failed to enable u3phya_ref\n");
+		return ret;
+	}
+
+	phy_instance_init(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_on(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_on(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_off(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_off(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_exit(struct phy *phy)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	clk_disable_unprepare(u3phy->u3phya_ref);
+	return 0;
+}
+
+static struct phy *mt65xx_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(dev);
+	struct mt65xx_phy_instance *instance = NULL;
+	struct device_node *phy_np = args->np;
+	int index;
+
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (index = 0; index < u3phy->nphys; index++)
+		if (phy_np == u3phy->phys[index]->phy->dev.of_node) {
+			instance = u3phy->phys[index];
+			break;
+		}
+
+	if (!instance) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	instance->type = args->args[0];
+
+	if (!(instance->type == PHY_TYPE_USB2 ||
+	      instance->type == PHY_TYPE_USB3)) {
+		dev_err(dev, "unsupported device type: %d\n", instance->type);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return instance->phy;
+}
+
+static struct phy_ops mt65xx_u3phy_ops = {
+	.init		= mt65xx_phy_init,
+	.exit		= mt65xx_phy_exit,
+	.power_on	= mt65xx_phy_power_on,
+	.power_off	= mt65xx_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int mt65xx_u3phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct resource *sif_res;
+	struct mt65xx_u3phy *u3phy;
+	struct resource res;
+	int port;
+
+	u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
+	if (!u3phy)
+		return -ENOMEM;
+
+	u3phy->nphys = of_get_child_count(np);
+	u3phy->phys = devm_kcalloc(dev, u3phy->nphys,
+				       sizeof(*u3phy->phys), GFP_KERNEL);
+	if (!u3phy->phys)
+		return -ENOMEM;
+
+	u3phy->dev = dev;
+	platform_set_drvdata(pdev, u3phy);
+
+	sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
+	if (IS_ERR(u3phy->sif_base)) {
+		dev_err(dev, "failed to remap sif regs\n");
+		return PTR_ERR(u3phy->sif_base);
+	}
+
+	u3phy->u3phya_ref = devm_clk_get(dev, "u3phya_ref");
+	if (IS_ERR(u3phy->u3phya_ref)) {
+		dev_err(dev, "error to get u3phya_ref\n");
+		return PTR_ERR(u3phy->u3phya_ref);
+	}
+
+	port = 0;
+	for_each_child_of_node(np, child_np) {
+		struct mt65xx_phy_instance *instance;
+		struct phy *phy;
+		int retval;
+
+		instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
+		if (!instance)
+			return -ENOMEM;
+
+		u3phy->phys[port] = instance;
+
+		phy = devm_phy_create(dev, child_np, &mt65xx_u3phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			return PTR_ERR(phy);
+		}
+
+		retval = of_address_to_resource(child_np, 0, &res);
+		if (retval) {
+			dev_err(dev, "failed to get address resource(id-%d)\n",
+				port);
+			return retval;
+		}
+
+		instance->port_base = devm_ioremap_resource(&phy->dev, &res);
+		if (IS_ERR(instance->port_base)) {
+			dev_err(dev, "failed to remap phy regs\n");
+			return PTR_ERR(instance->port_base);
+		}
+
+		instance->phy = phy;
+		instance->index = port;
+		phy_set_drvdata(phy, instance);
+		port++;
+	}
+
+	provider = devm_of_phy_provider_register(dev, mt65xx_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mt65xx_u3phy_id_table[] = {
+	{ .compatible = "mediatek,mt8173-u3phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
+
+static struct platform_driver mt65xx_u3phy_driver = {
+	.probe		= mt65xx_u3phy_probe,
+	.driver		= {
+		.name	= "mt65xx-u3phy",
+		.of_match_table = mt65xx_u3phy_id_table,
+	},
+};
+
+module_platform_driver(mt65xx_u3phy_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("mt65xx USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
1.8.1.1.dirty

[PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Chunfeng Yun]

support usb3.0 phy of mt65xx SoCs

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/phy/Kconfig           |   9 +
 drivers/phy/Makefile          |   1 +
 drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 466 insertions(+)
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 47da573..ec436c1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a5b18c1..a7cc629 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
new file mode 100644
index 0000000..1f00b05
--- /dev/null
+++ b/drivers/phy/phy-mt65xx-usb3.c
@@ -0,0 +1,456 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+/*
+ * for sifslv2 register, but exclude port's;
+ * relative to USB3_SIF2_BASE base address
+ */
+#define SSUSB_SIFSLV_SPLLC		0x0000
+
+/* offsets of sub-segment in each port registers */
+#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
+#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
+#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
+#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
+
+#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
+#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
+
+#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
+#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
+
+#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
+#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
+#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
+#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
+
+#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
+#define PA6_RG_U2_ISO_EN		BIT(31)
+#define PA6_RG_U2_BC11_SW_EN		BIT(23)
+#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
+
+#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
+#define P2C_RG_USB20_GPIO_CTL		BIT(9)
+#define P2C_USB20_GPIO_MODE		BIT(8)
+#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
+
+#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
+#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
+
+#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
+#define P2C_FORCE_UART_EN		BIT(26)
+#define P2C_FORCE_DATAIN		BIT(23)
+#define P2C_FORCE_DM_PULLDOWN		BIT(21)
+#define P2C_FORCE_DP_PULLDOWN		BIT(20)
+#define P2C_FORCE_XCVRSEL		BIT(19)
+#define P2C_FORCE_SUSPENDM		BIT(18)
+#define P2C_FORCE_TERMSEL		BIT(17)
+#define P2C_RG_DATAIN			GENMASK(13, 10)
+#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
+#define P2C_RG_DMPULLDOWN		BIT(7)
+#define P2C_RG_DPPULLDOWN		BIT(6)
+#define P2C_RG_XCVRSEL			GENMASK(5, 4)
+#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
+#define P2C_RG_SUSPENDM			BIT(3)
+#define P2C_RG_TERMSEL			BIT(2)
+#define P2C_DTM0_PART_MASK \
+		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
+		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
+		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
+		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
+
+#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
+#define P2C_RG_UART_EN			BIT(16)
+#define P2C_RG_VBUSVALID		BIT(5)
+#define P2C_RG_SESSEND			BIT(4)
+#define P2C_RG_AVALID			BIT(2)
+
+#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
+#define P3A_RG_U3_VUSB10_ON		BIT(5)
+
+#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
+#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
+#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
+
+#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
+#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
+#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
+
+#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
+#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
+#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
+
+#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
+#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
+#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
+#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
+#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
+
+#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
+#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
+#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
+
+struct mt65xx_phy_instance {
+	struct phy *phy;
+	void __iomem *port_base;
+	u32 index;
+	u8 type;
+};
+
+struct mt65xx_u3phy {
+	struct device *dev;
+	void __iomem *sif_base;	/* include sif2, but exclude port's */
+	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
+	struct mt65xx_phy_instance **phys;
+	int nphys;
+};
+
+static void phy_instance_init(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	/* switch to USB function. (system register, force ip into usb mode) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_FORCE_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~P2C_RG_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U2PHYACR4);
+		tmp &= ~P2C_U2_GPIO_CTR_MSK;
+		writel(tmp, port_base + U3P_U2PHYACR4);
+	}
+
+	/* DP/DM BC1.1 path Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_BC11_SW_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
+	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
+	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
+	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG9);
+	tmp &= ~P3A_RG_RX_DAC_MUX;
+	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
+	writel(tmp, port_base + U3P_U3_PHYA_REG9);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG6);
+	tmp &= ~P3A_RG_TX_EIDLE_CM;
+	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
+	writel(tmp, port_base + U3P_U3_PHYA_REG6);
+
+	tmp = readl(port_base + U3P_PHYD_CDR1);
+	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
+	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
+	writel(tmp, port_base + U3P_PHYD_CDR1);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	if (!index) {
+		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp |= P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
+	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Enable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	if (!index) {
+		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
+		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
+		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
+		/* [mt8173]disable Change 100uA current from SSUSB */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
+	tmp &= ~P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+	/* USB 2.0 slew rate calibration */
+	tmp = readl(port_base + U3P_USBPHYACR5);
+	tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
+	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(4);
+	writel(tmp, port_base + U3P_USBPHYACR5);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
+	tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
+	tmp |= P2C_FORCE_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+	if (!index) {
+		/* (also disable)Change 100uA current switch to USB2.0 */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	/* let suspendm=0, set utmi into analog power down */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_RG_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+	udelay(1);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
+	tmp |= P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static int mt65xx_phy_init(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	ret = clk_prepare_enable(u3phy->u3phya_ref);
+	if (ret) {
+		dev_err(u3phy->dev, "failed to enable u3phya_ref\n");
+		return ret;
+	}
+
+	phy_instance_init(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_on(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_on(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_off(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_off(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_exit(struct phy *phy)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	clk_disable_unprepare(u3phy->u3phya_ref);
+	return 0;
+}
+
+static struct phy *mt65xx_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(dev);
+	struct mt65xx_phy_instance *instance = NULL;
+	struct device_node *phy_np = args->np;
+	int index;
+
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (index = 0; index < u3phy->nphys; index++)
+		if (phy_np == u3phy->phys[index]->phy->dev.of_node) {
+			instance = u3phy->phys[index];
+			break;
+		}
+
+	if (!instance) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	instance->type = args->args[0];
+
+	if (!(instance->type == PHY_TYPE_USB2 ||
+	      instance->type == PHY_TYPE_USB3)) {
+		dev_err(dev, "unsupported device type: %d\n", instance->type);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return instance->phy;
+}
+
+static struct phy_ops mt65xx_u3phy_ops = {
+	.init		= mt65xx_phy_init,
+	.exit		= mt65xx_phy_exit,
+	.power_on	= mt65xx_phy_power_on,
+	.power_off	= mt65xx_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int mt65xx_u3phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct resource *sif_res;
+	struct mt65xx_u3phy *u3phy;
+	struct resource res;
+	int port;
+
+	u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
+	if (!u3phy)
+		return -ENOMEM;
+
+	u3phy->nphys = of_get_child_count(np);
+	u3phy->phys = devm_kcalloc(dev, u3phy->nphys,
+				       sizeof(*u3phy->phys), GFP_KERNEL);
+	if (!u3phy->phys)
+		return -ENOMEM;
+
+	u3phy->dev = dev;
+	platform_set_drvdata(pdev, u3phy);
+
+	sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
+	if (IS_ERR(u3phy->sif_base)) {
+		dev_err(dev, "failed to remap sif regs\n");
+		return PTR_ERR(u3phy->sif_base);
+	}
+
+	u3phy->u3phya_ref = devm_clk_get(dev, "u3phya_ref");
+	if (IS_ERR(u3phy->u3phya_ref)) {
+		dev_err(dev, "error to get u3phya_ref\n");
+		return PTR_ERR(u3phy->u3phya_ref);
+	}
+
+	port = 0;
+	for_each_child_of_node(np, child_np) {
+		struct mt65xx_phy_instance *instance;
+		struct phy *phy;
+		int retval;
+
+		instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
+		if (!instance)
+			return -ENOMEM;
+
+		u3phy->phys[port] = instance;
+
+		phy = devm_phy_create(dev, child_np, &mt65xx_u3phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			return PTR_ERR(phy);
+		}
+
+		retval = of_address_to_resource(child_np, 0, &res);
+		if (retval) {
+			dev_err(dev, "failed to get address resource(id-%d)\n",
+				port);
+			return retval;
+		}
+
+		instance->port_base = devm_ioremap_resource(&phy->dev, &res);
+		if (IS_ERR(instance->port_base)) {
+			dev_err(dev, "failed to remap phy regs\n");
+			return PTR_ERR(instance->port_base);
+		}
+
+		instance->phy = phy;
+		instance->index = port;
+		phy_set_drvdata(phy, instance);
+		port++;
+	}
+
+	provider = devm_of_phy_provider_register(dev, mt65xx_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mt65xx_u3phy_id_table[] = {
+	{ .compatible = "mediatek,mt8173-u3phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
+
+static struct platform_driver mt65xx_u3phy_driver = {
+	.probe		= mt65xx_u3phy_probe,
+	.driver		= {
+		.name	= "mt65xx-u3phy",
+		.of_match_table = mt65xx_u3phy_id_table,
+	},
+};
+
+module_platform_driver(mt65xx_u3phy_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("mt65xx USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
1.8.1.1.dirty

[PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Chunfeng Yun]

support usb3.0 phy of mt65xx SoCs

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/phy/Kconfig           |   9 +
 drivers/phy/Makefile          |   1 +
 drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 466 insertions(+)
 create mode 100644 drivers/phy/phy-mt65xx-usb3.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 47da573..ec436c1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a5b18c1..a7cc629 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
new file mode 100644
index 0000000..1f00b05
--- /dev/null
+++ b/drivers/phy/phy-mt65xx-usb3.c
@@ -0,0 +1,456 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+/*
+ * for sifslv2 register, but exclude port's;
+ * relative to USB3_SIF2_BASE base address
+ */
+#define SSUSB_SIFSLV_SPLLC		0x0000
+
+/* offsets of sub-segment in each port registers */
+#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
+#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
+#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
+#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
+
+#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
+#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
+
+#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
+#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
+
+#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
+#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
+#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
+#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
+
+#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
+#define PA6_RG_U2_ISO_EN		BIT(31)
+#define PA6_RG_U2_BC11_SW_EN		BIT(23)
+#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
+
+#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
+#define P2C_RG_USB20_GPIO_CTL		BIT(9)
+#define P2C_USB20_GPIO_MODE		BIT(8)
+#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
+
+#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
+#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
+
+#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
+#define P2C_FORCE_UART_EN		BIT(26)
+#define P2C_FORCE_DATAIN		BIT(23)
+#define P2C_FORCE_DM_PULLDOWN		BIT(21)
+#define P2C_FORCE_DP_PULLDOWN		BIT(20)
+#define P2C_FORCE_XCVRSEL		BIT(19)
+#define P2C_FORCE_SUSPENDM		BIT(18)
+#define P2C_FORCE_TERMSEL		BIT(17)
+#define P2C_RG_DATAIN			GENMASK(13, 10)
+#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
+#define P2C_RG_DMPULLDOWN		BIT(7)
+#define P2C_RG_DPPULLDOWN		BIT(6)
+#define P2C_RG_XCVRSEL			GENMASK(5, 4)
+#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
+#define P2C_RG_SUSPENDM			BIT(3)
+#define P2C_RG_TERMSEL			BIT(2)
+#define P2C_DTM0_PART_MASK \
+		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
+		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
+		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
+		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
+
+#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
+#define P2C_RG_UART_EN			BIT(16)
+#define P2C_RG_VBUSVALID		BIT(5)
+#define P2C_RG_SESSEND			BIT(4)
+#define P2C_RG_AVALID			BIT(2)
+
+#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
+#define P3A_RG_U3_VUSB10_ON		BIT(5)
+
+#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
+#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
+#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
+
+#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
+#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
+#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
+
+#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
+#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
+#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
+
+#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
+#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
+#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
+#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
+#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
+
+#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
+#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
+#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
+
+struct mt65xx_phy_instance {
+	struct phy *phy;
+	void __iomem *port_base;
+	u32 index;
+	u8 type;
+};
+
+struct mt65xx_u3phy {
+	struct device *dev;
+	void __iomem *sif_base;	/* include sif2, but exclude port's */
+	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
+	struct mt65xx_phy_instance **phys;
+	int nphys;
+};
+
+static void phy_instance_init(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	/* switch to USB function. (system register, force ip into usb mode) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_FORCE_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~P2C_RG_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U2PHYACR4);
+		tmp &= ~P2C_U2_GPIO_CTR_MSK;
+		writel(tmp, port_base + U3P_U2PHYACR4);
+	}
+
+	/* DP/DM BC1.1 path Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_BC11_SW_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
+	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
+	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
+	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG9);
+	tmp &= ~P3A_RG_RX_DAC_MUX;
+	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
+	writel(tmp, port_base + U3P_U3_PHYA_REG9);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG6);
+	tmp &= ~P3A_RG_TX_EIDLE_CM;
+	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
+	writel(tmp, port_base + U3P_U3_PHYA_REG6);
+
+	tmp = readl(port_base + U3P_PHYD_CDR1);
+	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
+	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
+	writel(tmp, port_base + U3P_PHYD_CDR1);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	if (!index) {
+		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp |= P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
+	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Enable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	if (!index) {
+		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
+		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
+		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
+		/* [mt8173]disable Change 100uA current from SSUSB */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
+	tmp &= ~P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+	/* USB 2.0 slew rate calibration */
+	tmp = readl(port_base + U3P_USBPHYACR5);
+	tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
+	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(4);
+	writel(tmp, port_base + U3P_USBPHYACR5);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
+	tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
+	tmp |= P2C_FORCE_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+	if (!index) {
+		/* (also disable)Change 100uA current switch to USB2.0 */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+	udelay(800);
+
+	/* let suspendm=0, set utmi into analog power down */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_RG_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+	udelay(1);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
+	tmp |= P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static int mt65xx_phy_init(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	ret = clk_prepare_enable(u3phy->u3phya_ref);
+	if (ret) {
+		dev_err(u3phy->dev, "failed to enable u3phya_ref\n");
+		return ret;
+	}
+
+	phy_instance_init(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_on(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_on(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_off(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_off(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_exit(struct phy *phy)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	clk_disable_unprepare(u3phy->u3phya_ref);
+	return 0;
+}
+
+static struct phy *mt65xx_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(dev);
+	struct mt65xx_phy_instance *instance = NULL;
+	struct device_node *phy_np = args->np;
+	int index;
+
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (index = 0; index < u3phy->nphys; index++)
+		if (phy_np == u3phy->phys[index]->phy->dev.of_node) {
+			instance = u3phy->phys[index];
+			break;
+		}
+
+	if (!instance) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	instance->type = args->args[0];
+
+	if (!(instance->type == PHY_TYPE_USB2 ||
+	      instance->type == PHY_TYPE_USB3)) {
+		dev_err(dev, "unsupported device type: %d\n", instance->type);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return instance->phy;
+}
+
+static struct phy_ops mt65xx_u3phy_ops = {
+	.init		= mt65xx_phy_init,
+	.exit		= mt65xx_phy_exit,
+	.power_on	= mt65xx_phy_power_on,
+	.power_off	= mt65xx_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int mt65xx_u3phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct resource *sif_res;
+	struct mt65xx_u3phy *u3phy;
+	struct resource res;
+	int port;
+
+	u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
+	if (!u3phy)
+		return -ENOMEM;
+
+	u3phy->nphys = of_get_child_count(np);
+	u3phy->phys = devm_kcalloc(dev, u3phy->nphys,
+				       sizeof(*u3phy->phys), GFP_KERNEL);
+	if (!u3phy->phys)
+		return -ENOMEM;
+
+	u3phy->dev = dev;
+	platform_set_drvdata(pdev, u3phy);
+
+	sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
+	if (IS_ERR(u3phy->sif_base)) {
+		dev_err(dev, "failed to remap sif regs\n");
+		return PTR_ERR(u3phy->sif_base);
+	}
+
+	u3phy->u3phya_ref = devm_clk_get(dev, "u3phya_ref");
+	if (IS_ERR(u3phy->u3phya_ref)) {
+		dev_err(dev, "error to get u3phya_ref\n");
+		return PTR_ERR(u3phy->u3phya_ref);
+	}
+
+	port = 0;
+	for_each_child_of_node(np, child_np) {
+		struct mt65xx_phy_instance *instance;
+		struct phy *phy;
+		int retval;
+
+		instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
+		if (!instance)
+			return -ENOMEM;
+
+		u3phy->phys[port] = instance;
+
+		phy = devm_phy_create(dev, child_np, &mt65xx_u3phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			return PTR_ERR(phy);
+		}
+
+		retval = of_address_to_resource(child_np, 0, &res);
+		if (retval) {
+			dev_err(dev, "failed to get address resource(id-%d)\n",
+				port);
+			return retval;
+		}
+
+		instance->port_base = devm_ioremap_resource(&phy->dev, &res);
+		if (IS_ERR(instance->port_base)) {
+			dev_err(dev, "failed to remap phy regs\n");
+			return PTR_ERR(instance->port_base);
+		}
+
+		instance->phy = phy;
+		instance->index = port;
+		phy_set_drvdata(phy, instance);
+		port++;
+	}
+
+	provider = devm_of_phy_provider_register(dev, mt65xx_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mt65xx_u3phy_id_table[] = {
+	{ .compatible = "mediatek,mt8173-u3phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
+
+static struct platform_driver mt65xx_u3phy_driver = {
+	.probe		= mt65xx_u3phy_probe,
+	.driver		= {
+		.name	= "mt65xx-u3phy",
+		.of_match_table = mt65xx_u3phy_id_table,
+	},
+};
+
+module_platform_driver(mt65xx_u3phy_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("mt65xx USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
1.8.1.1.dirty

[PATCH v8 4/5] xhci: mediatek: support MTK xHCI host controller

[Chunfeng Yun]

There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
  to minimize the scheduling effort for synchronous and
  interrupt endpoints. The parameters are put into reseved
  DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
  8 times as much as that defined in xHCI spec.
3. Its TDS in  Normal TRB defines a number of packets that
  remains to be transferred for a TD after processing all
  Max packets in all previous TRBs.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/usb/host/Kconfig        |   9 +
 drivers/usb/host/Makefile       |   4 +
 drivers/usb/host/xhci-mtk-sch.c | 419 ++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.c     | 744 ++++++++++++++++++++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h     | 156 +++++++++
 drivers/usb/host/xhci-ring.c    |  22 +-
 drivers/usb/host/xhci.c         |  19 +-
 drivers/usb/host/xhci.h         |   1 +
 8 files changed, 1367 insertions(+), 7 deletions(-)
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 079991e..4674118 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -41,6 +41,15 @@ config USB_XHCI_PLATFORM
 
 	  If unsure, say N.
 
+config USB_XHCI_MTK
+	tristate "xHCI support for Mediatek MT65xx"
+	select MFD_SYSCON
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	---help---
+	  Say 'Y' to enable the support for the xHCI host controller
+	  found in Mediatek MT65xx SoCs.
+	  If unsure, say N.
+
 config USB_XHCI_MVEBU
 	tristate "xHCI support for Marvell Armada 375/38x"
 	select USB_XHCI_PLATFORM
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 754efaa..00401f9 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -13,6 +13,9 @@ fhci-$(CONFIG_FHCI_DEBUG) += fhci-dbg.o
 xhci-hcd-y := xhci.o xhci-mem.o
 xhci-hcd-y += xhci-ring.o xhci-hub.o xhci-dbg.o
 xhci-hcd-y += xhci-trace.o
+ifneq ($(CONFIG_USB_XHCI_MTK), )
+	xhci-hcd-y += xhci-mtk-sch.o
+endif
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -30,6 +33,7 @@ endif
 
 obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
new file mode 100644
index 0000000..534d089
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -0,0 +1,419 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Zhigang.Wei <zhigang.wei@mediatek.com>
+ *  Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include "xhci.h"
+#include "xhci-mtk.h"
+
+#define SS_BW_BOUNDARY	51000
+/* table 5-5. High-speed Isoc Transaction Limits in usb_20 spec */
+#define HS_BW_BOUNDARY	6144
+/* usb2 spec section11.18.1: at most 188 FS bytes per microframe */
+#define FS_PAYLOAD_MAX 188
+
+/* mtk scheduler bitmasks */
+#define EP_BPKTS(p)	((p) & 0x3f)
+#define EP_BCSCOUNT(p)	(((p) & 0x7) << 8)
+#define EP_BBM(p)	((p) << 11)
+#define EP_BOFFSET(p)	((p) & 0x3fff)
+#define EP_BREPEAT(p)	(((p) & 0x7fff) << 16)
+
+static int is_fs_or_ls(enum usb_device_speed speed)
+{
+	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
+}
+
+/*
+* get the index of bandwidth domains array which @ep belongs to.
+*
+* the bandwidth domain array is saved to @sch_array of struct xhci_hcd_mtk,
+* each HS root port is treated as a single bandwidth domain,
+* but each SS root port is treated as two bandwidth domains, one for IN eps,
+* one for OUT eps.
+* @real_port value is defined as follow according to xHCI spec:
+* 1 for SSport0, ..., N+1 for SSportN, N+2 for HSport0, N+3 for HSport1, etc
+* so the bandwidth domain array is organized as follow for simplification:
+* SSport0-OUT, SSport0-IN, ..., SSportX-OUT, SSportX-IN, HSport0, ..., HSportY
+*/
+static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
+	struct usb_host_endpoint *ep)
+{
+	struct xhci_virt_device *virt_dev;
+	int bw_index;
+
+	virt_dev = xhci->devs[udev->slot_id];
+
+	if (udev->speed == USB_SPEED_SUPER) {
+		if (usb_endpoint_dir_out(&ep->desc))
+			bw_index = (virt_dev->real_port - 1) * 2;
+		else
+			bw_index = (virt_dev->real_port - 1) * 2 + 1;
+	} else {
+		/* add one more for each SS port */
+		bw_index = virt_dev->real_port + xhci->num_usb3_ports - 1;
+	}
+
+	return bw_index;
+}
+
+static void setup_sch_info(struct usb_device *udev,
+		struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 ep_type;
+	u32 ep_interval;
+	u32 max_packet_size;
+	u32 max_burst;
+	u32 mult;
+	u32 esit_pkts;
+
+	ep_type = CTX_TO_EP_TYPE(le32_to_cpu(ep_ctx->ep_info2));
+	ep_interval = CTX_TO_EP_INTERVAL(le32_to_cpu(ep_ctx->ep_info));
+	max_packet_size = MAX_PACKET_DECODED(le32_to_cpu(ep_ctx->ep_info2));
+	max_burst = CTX_TO_MAX_BURST(le32_to_cpu(ep_ctx->ep_info2));
+	mult = CTX_TO_EP_MULT(le32_to_cpu(ep_ctx->ep_info));
+
+	sch_ep->esit = 1 << ep_interval;
+	sch_ep->offset = 0;
+	sch_ep->burst_mode = 0;
+
+	if (udev->speed == USB_SPEED_HIGH) {
+		sch_ep->cs_count = 0;
+
+		/*
+		 * usb_20 spec section5.9
+		 * a single microframe is enough for HS synchromous endpoints
+		 * in a interval
+		 */
+		sch_ep->num_budget_microframes = 1;
+		sch_ep->repeat = 0;
+
+		/*
+		 * xHCI spec section6.2.3.4
+		 * @max_burst is the number of additional transactions
+		 * opportunities per microframe
+		 */
+		sch_ep->pkts = max_burst + 1;
+		sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
+	} else if (udev->speed == USB_SPEED_SUPER) {
+		/* usb3_r1 spec section4.4.7 & 4.4.8 */
+		sch_ep->cs_count = 0;
+		esit_pkts = (mult + 1) * (max_burst + 1);
+		if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
+			sch_ep->pkts = esit_pkts;
+			sch_ep->num_budget_microframes = 1;
+			sch_ep->repeat = 0;
+		}
+
+		if (ep_type == ISOC_IN_EP || ep_type == ISOC_OUT_EP) {
+			if (esit_pkts <= sch_ep->esit)
+				sch_ep->pkts = 1;
+			else
+				sch_ep->pkts = roundup_pow_of_two(esit_pkts)
+					/ sch_ep->esit;
+
+			sch_ep->num_budget_microframes =
+				DIV_ROUND_UP(esit_pkts, sch_ep->pkts);
+
+			if (sch_ep->num_budget_microframes > 1)
+				sch_ep->repeat = 1;
+			else
+				sch_ep->repeat = 0;
+		}
+		sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
+	} else if (is_fs_or_ls(udev->speed)) {
+
+		/*
+		 * usb_20 spec section11.18.4
+		 * assume worst cases
+		 */
+		sch_ep->repeat = 0;
+		sch_ep->pkts = 1; /* at most one packet for each microframe */
+		if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
+			sch_ep->cs_count = 3; /* at most need 3 CS*/
+			/* one for SS and one for budgeted transaction */
+			sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
+			sch_ep->bw_cost_per_microframe = max_packet_size;
+		}
+		if (ep_type == ISOC_OUT_EP) {
+			/* must never schedule a cs ISOC OUT ep */
+			sch_ep->cs_count = 0;
+
+			/*
+			 * the best case FS budget assumes that 188 FS bytes
+			 * occur in each microframe
+			 */
+			sch_ep->num_budget_microframes = DIV_ROUND_UP(
+				max_packet_size, FS_PAYLOAD_MAX);
+			sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
+		}
+		if (ep_type == ISOC_IN_EP) {
+			/* at most need additional two CS. */
+			sch_ep->cs_count = DIV_ROUND_UP(
+				max_packet_size, FS_PAYLOAD_MAX) + 2;
+			sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
+			sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
+		}
+	}
+}
+
+/* Get maximum bandwidth when we schedule at offset slot. */
+static u32 get_max_bw(struct mu3h_sch_bw_info *sch_bw,
+	struct mu3h_sch_ep_info *sch_ep, u32 offset)
+{
+	u32 num_esit;
+	u32 max_bw = 0;
+	int i;
+	int j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		u32 base = offset + i * sch_ep->esit;
+
+		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
+			if (sch_bw->bus_bw[base + j] > max_bw)
+				max_bw = sch_bw->bus_bw[base + j];
+		}
+	}
+	return max_bw;
+}
+
+static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
+	struct mu3h_sch_ep_info *sch_ep, int bw_cost)
+{
+	u32 num_esit;
+	u32 base;
+	int i;
+	int j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		base = sch_ep->offset + i * sch_ep->esit;
+		for (j = 0; j < sch_ep->num_budget_microframes; j++)
+			sch_bw->bus_bw[base + j] += bw_cost;
+	}
+}
+
+static int check_sch_bw(struct usb_device *udev,
+	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 offset;
+	u32 esit;
+	u32 num_budget_microframes;
+	u32 min_bw;
+	u32 min_index;
+	u32 worst_bw;
+	u32 bw_boundary;
+
+	if (sch_ep->esit > XHCI_MTK_MAX_ESIT)
+		sch_ep->esit = XHCI_MTK_MAX_ESIT;
+
+	esit = sch_ep->esit;
+	num_budget_microframes = sch_ep->num_budget_microframes;
+
+	/*
+	 * Search through all possible schedule microframes.
+	 * and find a microframe where its worst bandwidth is minimum.
+	 */
+	min_bw = ~0;
+	min_index = 0;
+	for (offset = 0; offset < esit; offset++) {
+		if ((offset + num_budget_microframes) > sch_ep->esit)
+			break;
+
+		/*
+		 * usb_20 spec section11.18:
+		 * must never schedule Start-Split in Y6
+		 */
+		if (is_fs_or_ls(udev->speed) && (offset % 8 == 6))
+			continue;
+
+		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
+		if (min_bw > worst_bw) {
+			min_bw = worst_bw;
+			min_index = offset;
+		}
+		if (min_bw == 0)
+			break;
+	}
+	sch_ep->offset = min_index;
+
+	bw_boundary = (udev->speed == USB_SPEED_SUPER)
+				? SS_BW_BOUNDARY : HS_BW_BOUNDARY;
+
+	/* check bandwidth */
+	if (min_bw + sch_ep->bw_cost_per_microframe > bw_boundary)
+		return -ERANGE;
+
+	/* update bus bandwidth info */
+	update_bus_bw(sch_bw, sch_ep, sch_ep->bw_cost_per_microframe);
+
+	return 0;
+}
+
+static bool need_bw_sch(struct usb_host_endpoint *ep,
+	enum usb_device_speed speed, int has_tt)
+{
+	/* only for periodic endpoints */
+	if (usb_endpoint_xfer_control(&ep->desc)
+		|| usb_endpoint_xfer_bulk(&ep->desc))
+		return false;
+
+	/*
+	 * for LS & FS periodic endpoints which its device don't attach
+	 * to TT are also ignored, root-hub will schedule them directly
+	 */
+	if (is_fs_or_ls(speed) && !has_tt)
+		return false;
+
+	return true;
+}
+
+int xhci_mtk_sch_init(struct xhci_hcd *xhci)
+{
+	struct usb_hcd *hcd = xhci_to_hcd(xhci);
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+	struct mu3h_sch_bw_info *sch_array;
+	int num_usb_bus;
+	int i;
+
+	/* ss IN and OUT are separated */
+	num_usb_bus = xhci->num_usb3_ports * 2 + xhci->num_usb2_ports;
+
+	sch_array = kcalloc(num_usb_bus, sizeof(*sch_array), GFP_KERNEL);
+	if (sch_array == NULL)
+		return -ENOMEM;
+
+	for (i = 0; i < num_usb_bus; i++)
+		INIT_LIST_HEAD(&sch_array[i].bw_ep_list);
+
+	mtk->sch_array = sch_array;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_sch_init);
+
+void xhci_mtk_sch_exit(struct xhci_hcd *xhci)
+{
+	struct usb_hcd *hcd = xhci_to_hcd(xhci);
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	kfree(mtk->sch_array);
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_sch_exit);
+
+int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	int ret = 0;
+	int bw_index;
+	struct xhci_hcd *xhci;
+	unsigned int ep_index;
+	struct xhci_ep_ctx *ep_ctx;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_virt_device *virt_dev;
+	struct mu3h_sch_bw_info *sch_bw;
+	struct mu3h_sch_ep_info *sch_ep;
+	struct mu3h_sch_bw_info *sch_array;
+
+	xhci = hcd_to_xhci(hcd);
+	virt_dev = xhci->devs[udev->slot_id];
+	ep_index = xhci_get_endpoint_index(&ep->desc);
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
+	sch_array = mtk->sch_array;
+
+	xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
+		usb_endpoint_type(&ep->desc), udev->speed, ep);
+
+	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+		return 0;
+
+	bw_index = get_bw_index(xhci, udev, ep);
+	sch_bw = &sch_array[bw_index];
+
+	sch_ep = kzalloc(sizeof(struct mu3h_sch_ep_info), GFP_NOIO);
+	if (!sch_ep)
+		return -ENOMEM;
+
+	setup_sch_info(udev, ep_ctx, sch_ep);
+
+	ret = check_sch_bw(udev, sch_bw, sch_ep);
+	if (ret) {
+		xhci_err(xhci, "Not enough bandwidth!\n");
+		kfree(sch_ep);
+		return -ENOSPC;
+	}
+
+	list_add_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
+	sch_ep->ep = ep;
+
+	ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
+		| EP_BCSCOUNT(sch_ep->cs_count) | EP_BBM(sch_ep->burst_mode));
+	ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
+		| EP_BREPEAT(sch_ep->repeat));
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
+
+void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	int bw_index;
+	struct xhci_hcd *xhci;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_virt_device *virt_dev;
+	struct mu3h_sch_bw_info *sch_array;
+	struct mu3h_sch_bw_info *sch_bw;
+	struct mu3h_sch_ep_info *sch_ep;
+
+	xhci = hcd_to_xhci(hcd);
+	virt_dev = xhci->devs[udev->slot_id];
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	sch_array = mtk->sch_array;
+
+	xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
+		usb_endpoint_type(&ep->desc), udev->speed, ep);
+
+	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+		return;
+
+	bw_index = get_bw_index(xhci, udev, ep);
+	sch_bw = &sch_array[bw_index];
+
+	list_for_each_entry(sch_ep, &sch_bw->bw_ep_list, endpoint) {
+		if (sch_ep->ep == ep) {
+			update_bus_bw(sch_bw, sch_ep,
+				-sch_ep->bw_cost_per_microframe);
+			list_del(&sch_ep->endpoint);
+			kfree(sch_ep);
+			break;
+		}
+	}
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
new file mode 100644
index 0000000..4510fef
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk.c
@@ -0,0 +1,744 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/usb/phy.h>
+#include <linux/usb/xhci_pdriver.h>
+
+#include "xhci.h"
+#include "xhci-mtk.h"
+
+/* ip_pw_ctrl0 register */
+#define CTRL0_IP_SW_RST	BIT(0)
+
+/* ip_pw_ctrl1 register */
+#define CTRL1_IP_HOST_PDN	BIT(0)
+
+/* ip_pw_ctrl2 register */
+#define CTRL2_IP_DEV_PDN	BIT(0)
+
+/* ip_pw_sts1 register */
+#define STS1_IP_SLEEP_STS	BIT(30)
+#define STS1_U3_MAC_RST	BIT(16)
+#define STS1_SYS125_RST	BIT(10)
+#define STS1_REF_RST		BIT(8)
+#define STS1_SYSPLL_STABLE	BIT(0)
+
+/* ip_pw_sts2 register */
+#define STS2_U2_MAC_RST	BIT(0)
+
+/* ip_xhci_cap register */
+#define CAP_U3_PORT_NUM(p)	((p) & 0xff)
+#define CAP_U2_PORT_NUM(p)	(((p) >> 8) & 0xff)
+
+/* u3_ctrl_p register */
+#define CTRL_U3_PORT_HOST_SEL	BIT(2)
+#define CTRL_U3_PORT_PDN	BIT(1)
+#define CTRL_U3_PORT_DIS	BIT(0)
+
+/* u2_ctrl_p register */
+#define CTRL_U2_PORT_HOST_SEL	BIT(2)
+#define CTRL_U2_PORT_PDN	BIT(1)
+#define CTRL_U2_PORT_DIS	BIT(0)
+
+/* u2_phy_pll register */
+#define CTRL_U2_FORCE_PLL_STB	BIT(28)
+
+#define PERI_WK_CTRL0		0x400
+#define UWK_CTR0_0P_LS_PE	BIT(8)  /* posedge */
+#define UWK_CTR0_0P_LS_NE	BIT(7)  /* negedge for 0p linestate*/
+#define UWK_CTL1_1P_LS_C(x)	(((x) & 0xf) << 1)
+#define UWK_CTL1_1P_LS_E	BIT(0)
+
+#define PERI_WK_CTRL1		0x404
+#define UWK_CTL1_IS_C(x)	(((x) & 0xf) << 26)
+#define UWK_CTL1_IS_E		BIT(25)
+#define UWK_CTL1_0P_LS_C(x)	(((x) & 0xf) << 21)
+#define UWK_CTL1_0P_LS_E	BIT(20)
+#define UWK_CTL1_IDDIG_C(x)	(((x) & 0xf) << 11)  /* cycle debounce */
+#define UWK_CTL1_IDDIG_E	BIT(10) /* enable debounce */
+#define UWK_CTL1_IDDIG_P	BIT(9)  /* polarity */
+#define UWK_CTL1_0P_LS_P	BIT(7)
+#define UWK_CTL1_IS_P		BIT(6)  /* polarity for ip sleep */
+
+enum ssusb_wakeup_src {
+	SSUSB_WK_IP_SLEEP = 1,
+	SSUSB_WK_LINE_STATE = 2,
+};
+
+static int check_ip_clk_status(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 val, check_val;
+	int ret;
+
+	check_val = STS1_SYSPLL_STABLE | STS1_REF_RST | STS1_SYS125_RST;
+	check_val |= (mtk->num_u3_ports ? STS1_U3_MAC_RST : 0);
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts1, val,
+			  (check_val == (val & check_val)), 100, 20000);
+	if (ret) {
+		dev_err(mtk->dev, "mac3 clocks are not stable (0x%x)\n", val);
+		return ret;
+	}
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts2, val,
+			   (val & STS2_U2_MAC_RST), 100, 10000);
+	if (ret) {
+		dev_err(mtk->dev, "mac2 reset is still active!!!\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xhci_mtk_ports_enable(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+	int i;
+
+	/* power on host ip */
+	temp = readl(&ippc->ip_pw_ctr1);
+	temp &= ~CTRL1_IP_HOST_PDN;
+	writel(temp, &ippc->ip_pw_ctr1);
+
+	/* power on and enable all u3 ports */
+	for (i = 0; i < mtk->num_u3_ports; i++) {
+		temp = readl(&ippc->u3_ctrl_p[i]);
+		temp &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS);
+		temp |= CTRL_U3_PORT_HOST_SEL;
+		writel(temp, &ippc->u3_ctrl_p[i]);
+	}
+
+	/* power on and enable all u2 ports */
+	for (i = 0; i < mtk->num_u2_ports; i++) {
+		temp = readl(&ippc->u2_ctrl_p[i]);
+		temp &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS);
+		temp |= CTRL_U2_PORT_HOST_SEL;
+		writel(temp, &ippc->u2_ctrl_p[i]);
+	}
+
+	/*
+	 * wait for clocks to be stable, and clock domains reset to
+	 * be inactive after power on and enable ports
+	 */
+	return check_ip_clk_status(mtk);
+}
+
+static int xhci_mtk_ports_disable(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+	int ret;
+	int i;
+
+	/* power down all u3 ports */
+	for (i = 0; i < mtk->num_u3_ports; i++) {
+		temp = readl(&ippc->u3_ctrl_p[i]);
+		temp |= CTRL_U3_PORT_PDN;
+		writel(temp, &ippc->u3_ctrl_p[i]);
+	}
+
+	/* power down all u2 ports */
+	for (i = 0; i < mtk->num_u2_ports; i++) {
+		temp = readl(&ippc->u2_ctrl_p[i]);
+		temp |= CTRL_U2_PORT_PDN;
+		writel(temp, &ippc->u2_ctrl_p[i]);
+	}
+
+	/* power down host ip */
+	temp = readl(&ippc->ip_pw_ctr1);
+	temp |= CTRL1_IP_HOST_PDN;
+	writel(temp, &ippc->ip_pw_ctr1);
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts1, temp,
+			  (temp & STS1_IP_SLEEP_STS), 100, 100000);
+	if (ret) {
+		dev_err(mtk->dev, "ip sleep failed!!!\n");
+		return ret;
+	}
+	return 0;
+}
+
+static void xhci_mtk_ports_config(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+
+	/* reset whole ip */
+	temp = readl(&ippc->ip_pw_ctr0);
+	temp |= CTRL0_IP_SW_RST;
+	writel(temp, &ippc->ip_pw_ctr0);
+	udelay(1);
+	temp = readl(&ippc->ip_pw_ctr0);
+	temp &= ~CTRL0_IP_SW_RST;
+	writel(temp, &ippc->ip_pw_ctr0);
+
+	/*
+	 * device ip is default power-on in fact
+	 * power down device ip, otherwise ip-sleep will fail
+	 */
+	temp = readl(&ippc->ip_pw_ctr2);
+	temp |= CTRL2_IP_DEV_PDN;
+	writel(temp, &ippc->ip_pw_ctr2);
+
+	temp = readl(&ippc->ip_xhci_cap);
+	mtk->num_u3_ports = CAP_U3_PORT_NUM(temp);
+	mtk->num_u2_ports = CAP_U2_PORT_NUM(temp);
+	dev_dbg(mtk->dev, "%s u2p:%d, u3p:%d\n", __func__,
+			mtk->num_u2_ports, mtk->num_u3_ports);
+
+	xhci_mtk_ports_enable(mtk);
+}
+
+static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk)
+{
+	int ret;
+
+	ret = clk_prepare_enable(mtk->sys_clk);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable u3phya_ref\n");
+		goto u3phya_ref_err;
+	}
+	ret = clk_prepare_enable(mtk->wk_deb_p0);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable wk_deb_p0\n");
+		goto usb_p0_err;
+	}
+	if (mtk->num_phys > 1) {
+		ret = clk_prepare_enable(mtk->wk_deb_p1);
+		if (ret) {
+			dev_err(mtk->dev, "failed to enable wk_deb_p1\n");
+			goto usb_p1_err;
+		}
+	}
+	return 0;
+
+usb_p1_err:
+	clk_disable_unprepare(mtk->wk_deb_p0);
+usb_p0_err:
+	clk_disable_unprepare(mtk->sys_clk);
+u3phya_ref_err:
+	return -EINVAL;
+}
+
+static void xhci_mtk_clks_disable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->num_phys > 1)
+		clk_disable_unprepare(mtk->wk_deb_p1);
+	clk_disable_unprepare(mtk->wk_deb_p0);
+	clk_disable_unprepare(mtk->sys_clk);
+}
+
+/* only clocks can be turn off for ip-sleep wakeup mode */
+static void usb_wakeup_ip_sleep_en(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_IS_P;
+	tmp &= ~(UWK_CTL1_IS_C(0xf));
+	tmp |= UWK_CTL1_IS_C(0x8);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_IS_E);
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	dev_dbg(mtk->dev, "%s(): WK_CTRL1[P6,E25,C26:29]=%#x\n",
+		__func__, tmp);
+}
+
+static void usb_wakeup_ip_sleep_dis(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+
+	regmap_read(mtk->pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_IS_E;
+	regmap_write(mtk->pericfg, PERI_WK_CTRL1, tmp);
+}
+
+/*
+* for line-state wakeup mode, phy's power should not power-down
+* and only support cable plug in/out
+*/
+static void usb_wakeup_line_state_en(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	/* line-state of u2-port0 */
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_0P_LS_P;
+	tmp &= ~(UWK_CTL1_0P_LS_C(0xf));
+	tmp |= UWK_CTL1_0P_LS_C(0x8);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_0P_LS_E);
+
+	/* line-state of u2-port1 if support */
+	if (mtk->num_phys > 1) {
+		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
+		tmp &= ~(UWK_CTL1_1P_LS_C(0xf));
+		tmp |= UWK_CTL1_1P_LS_C(0x8);
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp | UWK_CTL1_1P_LS_E);
+	}
+}
+
+static void usb_wakeup_line_state_dis(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_0P_LS_E;
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+
+	if (mtk->num_phys > 1) {
+		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
+		tmp &= ~UWK_CTL1_1P_LS_E;
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
+	}
+}
+
+static void usb_wakeup_enable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->wakeup_src == SSUSB_WK_IP_SLEEP)
+		usb_wakeup_ip_sleep_en(mtk);
+	else if (mtk->wakeup_src == SSUSB_WK_LINE_STATE)
+		usb_wakeup_line_state_en(mtk);
+}
+
+static void usb_wakeup_disable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->wakeup_src == SSUSB_WK_IP_SLEEP)
+		usb_wakeup_ip_sleep_dis(mtk);
+	else if (mtk->wakeup_src == SSUSB_WK_LINE_STATE)
+		usb_wakeup_line_state_dis(mtk);
+}
+
+static int usb_wakeup_of_property_parse(struct xhci_hcd_mtk *mtk,
+				struct device_node *dn)
+{
+	struct device *dev = mtk->dev;
+
+	/*
+	* wakeup function is optional, so it is not an error if this property
+	* does not exist, and in such case, no need to get relative
+	* properties anymore.
+	*/
+	of_property_read_u32(dn, "mediatek,wakeup-src", &mtk->wakeup_src);
+	if (!mtk->wakeup_src)
+		return 0;
+
+	mtk->wk_deb_p0 = devm_clk_get(dev, "wakeup_deb_p0");
+	if (IS_ERR(mtk->wk_deb_p0)) {
+		dev_err(dev, "fail to get wakeup_deb_p0\n");
+		return PTR_ERR(mtk->wk_deb_p0);
+	}
+
+	mtk->wk_deb_p1 = devm_clk_get(dev, "wakeup_deb_p1");
+	if (IS_ERR(mtk->wk_deb_p1)) {
+		dev_err(dev, "fail to get wakeup_deb_p1\n");
+		return PTR_ERR(mtk->wk_deb_p1);
+	}
+
+	mtk->pericfg = syscon_regmap_lookup_by_phandle(dn,
+						"mediatek,syscon-wakeup");
+	if (IS_ERR(mtk->pericfg)) {
+		dev_err(dev, "fail to get pericfg regs\n");
+		return PTR_ERR(mtk->pericfg);
+	}
+
+	return 0;
+}
+
+static int xhci_mtk_setup(struct usb_hcd *hcd);
+static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
+	.extra_priv_size = sizeof(struct xhci_hcd),
+	.reset = xhci_mtk_setup,
+};
+
+static struct hc_driver __read_mostly xhci_mtk_hc_driver;
+
+static int xhci_mtk_phy_enable(struct xhci_hcd_mtk *mtk)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < mtk->num_phys; i++) {
+		ret = phy_init(mtk->phys[i]);
+		if (ret)
+			goto disable_phy;
+		ret = phy_power_on(mtk->phys[i]);
+		if (ret) {
+			phy_exit(mtk->phys[i]);
+			goto disable_phy;
+		}
+	}
+	return 0;
+
+disable_phy:
+	for (; i > 0; i--) {
+		phy_power_off(mtk->phys[i - 1]);
+		phy_exit(mtk->phys[i - 1]);
+	}
+	return ret;
+}
+
+static void xhci_mtk_phy_disable(struct xhci_hcd_mtk *mtk)
+{
+	unsigned int i;
+
+	for (i = 0; i < mtk->num_phys; i++) {
+		phy_power_off(mtk->phys[i]);
+		phy_exit(mtk->phys[i]);
+	}
+}
+
+static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
+{
+	int ret;
+
+	ret = regulator_enable(mtk->vbus);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable vbus\n");
+		return ret;
+	}
+
+	ret = regulator_enable(mtk->vusb33);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable vusb33\n");
+		regulator_disable(mtk->vbus);
+		return ret;
+	}
+	return 0;
+}
+
+static void xhci_mtk_ldos_disable(struct xhci_hcd_mtk *mtk)
+{
+	regulator_disable(mtk->vbus);
+	regulator_disable(mtk->vusb33);
+}
+
+static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci)
+{
+	/*
+	 * As of now platform drivers don't provide MSI support so we ensure
+	 * here that the generic code does not try to make a pci_dev from our
+	 * dev struct in order to setup MSI
+	 */
+	xhci->quirks |= XHCI_PLAT;
+	xhci->quirks |= XHCI_MTK_HOST;
+	/*
+	 * MTK host controller gives a spurious successful event after a
+	 * short transfer. Ignore it.
+	 */
+	xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
+}
+
+/* called during probe() after chip reset completes */
+static int xhci_mtk_setup(struct usb_hcd *hcd)
+{
+	struct xhci_hcd *xhci;
+	int ret;
+
+	ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
+	if (ret)
+		return ret;
+
+	if (!usb_hcd_is_primary_hcd(hcd))
+		return 0;
+
+	xhci = hcd_to_xhci(hcd);
+	return xhci_mtk_sch_init(xhci);
+}
+
+
+static int xhci_mtk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct usb_xhci_pdata *pdata = dev_get_platdata(dev);
+	struct xhci_hcd_mtk *mtk;
+	const struct hc_driver *driver;
+	struct xhci_hcd *xhci;
+	struct resource *res;
+	struct usb_hcd *hcd;
+	struct phy *phy;
+	int phy_num;
+	int ret = -ENODEV;
+	int irq;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	driver = &xhci_mtk_hc_driver;
+	mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL);
+	if (!mtk)
+		return -ENOMEM;
+
+	mtk->dev = dev;
+	mtk->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(mtk->vbus)) {
+		dev_err(dev, "fail to get vbus\n");
+		return PTR_ERR(mtk->vbus);
+	}
+
+	mtk->vusb33 = devm_regulator_get(dev, "vusb33");
+	if (IS_ERR(mtk->vusb33)) {
+		dev_err(dev, "fail to get vusb33\n");
+		return PTR_ERR(mtk->vusb33);
+	}
+
+	mtk->sys_clk = devm_clk_get(dev, "sys_ck");
+	if (IS_ERR(mtk->sys_clk)) {
+		dev_err(dev, "fail to get sys_ck\n");
+		return PTR_ERR(mtk->sys_clk);
+	}
+
+	ret = usb_wakeup_of_property_parse(mtk, node);
+	if (ret)
+		return ret;
+
+	mtk->num_phys = of_count_phandle_with_args(node,
+			"phys", "#phy-cells");
+	if (mtk->num_phys > 0) {
+		mtk->phys = devm_kcalloc(dev, mtk->num_phys,
+					sizeof(*mtk->phys), GFP_KERNEL);
+		if (!mtk->phys)
+			return -ENOMEM;
+	} else {
+		mtk->num_phys = 0;
+	}
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	ret = xhci_mtk_ldos_enable(mtk);
+	if (ret)
+		goto disable_pm;
+
+	ret = xhci_mtk_clks_enable(mtk);
+	if (ret)
+		goto disable_ldos;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		goto disable_clk;
+
+	/* Initialize dma_mask and coherent_dma_mask to 32-bits */
+	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	if (ret)
+		goto disable_clk;
+
+	if (!dev->dma_mask)
+		dev->dma_mask = &dev->coherent_dma_mask;
+	else
+		dma_set_mask(dev, DMA_BIT_MASK(32));
+
+	hcd = usb_create_hcd(driver, dev, dev_name(dev));
+	if (!hcd) {
+		ret = -ENOMEM;
+		goto disable_clk;
+	}
+
+	/*
+	 * USB 2.0 roothub is stored in the platform_device.
+	 * Swap it with mtk HCD.
+	 */
+	mtk->hcd = platform_get_drvdata(pdev);
+	platform_set_drvdata(pdev, mtk);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hcd->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(hcd->regs)) {
+		ret = PTR_ERR(hcd->regs);
+		goto put_usb2_hcd;
+	}
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	mtk->ippc_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(mtk->ippc_regs)) {
+		ret = PTR_ERR(mtk->ippc_regs);
+		goto put_usb2_hcd;
+	}
+
+	for (phy_num = 0; phy_num < mtk->num_phys; phy_num++) {
+		phy = devm_of_phy_get_by_index(dev, node, phy_num);
+		if (IS_ERR(phy)) {
+			ret = PTR_ERR(phy);
+			goto put_usb2_hcd;
+		}
+		mtk->phys[phy_num] = phy;
+	}
+
+	xhci_mtk_ports_config(mtk);
+	xhci_mtk_phy_enable(mtk);
+	device_init_wakeup(dev, 1);
+
+	xhci = hcd_to_xhci(hcd);
+	xhci->main_hcd = hcd;
+	xhci->shared_hcd = usb_create_shared_hcd(driver, dev,
+			dev_name(dev), hcd);
+	if (!xhci->shared_hcd) {
+		ret = -ENOMEM;
+		goto disable_usb_phy;
+	}
+
+	if ((node && of_property_read_bool(node, "usb3-lpm-capable")) ||
+			(pdata && pdata->usb3_lpm_capable))
+		xhci->quirks |= XHCI_LPM_SUPPORT;
+
+	if (HCC_MAX_PSA(xhci->hcc_params) >= 4)
+		xhci->shared_hcd->can_do_streams = 1;
+
+	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto put_usb3_hcd;
+
+	ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto dealloc_usb2_hcd;
+
+	return 0;
+
+dealloc_usb2_hcd:
+	xhci_mtk_sch_exit(xhci);
+	usb_remove_hcd(hcd);
+
+put_usb3_hcd:
+	usb_put_hcd(xhci->shared_hcd);
+
+disable_usb_phy:
+	xhci_mtk_phy_disable(mtk);
+	device_init_wakeup(dev, 0);
+
+put_usb2_hcd:
+	usb_put_hcd(hcd);
+
+disable_clk:
+	xhci_mtk_clks_disable(mtk);
+
+disable_ldos:
+	xhci_mtk_ldos_disable(mtk);
+
+disable_pm:
+	pm_runtime_put_sync(dev);
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int xhci_mtk_remove(struct platform_device *dev)
+{
+	struct xhci_hcd_mtk *mtk = platform_get_drvdata(dev);
+	struct usb_hcd	*hcd = mtk->hcd;
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+
+	usb_remove_hcd(xhci->shared_hcd);
+	xhci_mtk_phy_disable(mtk);
+	device_init_wakeup(&dev->dev, 0);
+
+	usb_remove_hcd(hcd);
+	usb_put_hcd(xhci->shared_hcd);
+	usb_put_hcd(hcd);
+	xhci_mtk_sch_exit(xhci);
+	xhci_mtk_clks_disable(mtk);
+	xhci_mtk_ldos_disable(mtk);
+	pm_runtime_put_sync(&dev->dev);
+	pm_runtime_disable(&dev->dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int xhci_mtk_suspend(struct device *dev)
+{
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	xhci_mtk_ports_disable(mtk);
+	xhci_mtk_phy_disable(mtk);
+	xhci_mtk_clks_disable(mtk);
+	usb_wakeup_enable(mtk);
+	return 0;
+}
+
+static int xhci_mtk_resume(struct device *dev)
+{
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	usb_wakeup_disable(mtk);
+	xhci_mtk_clks_enable(mtk);
+	xhci_mtk_phy_enable(mtk);
+	xhci_mtk_ports_enable(mtk);
+	return 0;
+}
+
+static const struct dev_pm_ops xhci_mtk_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xhci_mtk_suspend, xhci_mtk_resume)
+};
+#define DEV_PM_OPS	(&xhci_mtk_pm_ops)
+#else
+#define DEV_PM_OPS	NULL
+#endif /* CONFIG_PM */
+
+#ifdef CONFIG_OF
+static const struct of_device_id mtk_xhci_of_match[] = {
+	{ .compatible = "mediatek,mt8173-xhci"},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mtk_xhci_of_match);
+#endif
+
+static struct platform_driver mtk_xhci_driver = {
+	.probe	= xhci_mtk_probe,
+	.remove	= xhci_mtk_remove,
+	.driver	= {
+		.name = "xhci-mtk",
+		.pm = DEV_PM_OPS,
+		.of_match_table = of_match_ptr(mtk_xhci_of_match),
+	},
+};
+
+static int __init xhci_mtk_init(void)
+{
+	xhci_init_driver(&xhci_mtk_hc_driver, &xhci_mtk_overrides);
+	return platform_driver_register(&mtk_xhci_driver);
+}
+module_init(xhci_mtk_init);
+
+static void __exit xhci_mtk_exit(void)
+{
+	platform_driver_unregister(&mtk_xhci_driver);
+}
+module_exit(xhci_mtk_exit);
+
+MODULE_DESCRIPTION("MediaTek xHCI Host Controller Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
new file mode 100644
index 0000000..8913c2f
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk.h
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Zhigang.Wei <zhigang.wei@mediatek.com>
+ *  Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _XHCI_MTK_H_
+#define _XHCI_MTK_H_
+
+#include "xhci.h"
+
+/**
+ * To simplify scheduler algorithm, set a upper limit for ESIT,
+ * if a synchromous ep's ESIT is larger than @XHCI_MTK_MAX_ESIT,
+ * round down to the limit value, that means allocating more
+ * bandwidth to it.
+ */
+#define XHCI_MTK_MAX_ESIT	64
+
+/**
+ * struct mu3h_sch_bw_info: schedule information for bandwidth domain
+ *
+ * @bus_bw: array to keep track of bandwidth already used at each uframes
+ * @bw_ep_list: eps in the bandwidth domain
+ *
+ * treat a HS root port as a bandwidth domain, but treat a SS root port as
+ * two bandwidth domains, one for IN eps and another for OUT eps.
+ */
+struct mu3h_sch_bw_info {
+	u32 bus_bw[XHCI_MTK_MAX_ESIT];
+	struct list_head bw_ep_list;
+};
+
+/**
+ * struct mu3h_sch_ep_info: schedule information for endpoint
+ *
+ * @esit: unit is 125us, equal to 2 << Interval field in ep-context
+ * @num_budget_microframes: number of continuous uframes
+ *		(@repeat==1) scheduled within the interval
+ * @bw_cost_per_microframe: bandwidth cost per microframe
+ * @endpoint: linked into bandwidth domain which it belongs to
+ * @ep: address of usb_host_endpoint struct
+ * @offset: which uframe of the interval that transfer should be
+ *		scheduled first time within the interval
+ * @repeat: the time gap between two uframes that transfers are
+ *		scheduled within a interval. in the simple algorithm, only
+ *		assign 0 or 1 to it; 0 means using only one uframe in a
+ *		interval, and 1 means using @num_budget_microframes
+ *		continuous uframes
+ * @pkts: number of packets to be transferred in the scheduled uframes
+ * @cs_count: number of CS that host will trigger
+ * @burst_mode: burst mode for scheduling. 0: normal burst mode,
+ *		distribute the bMaxBurst+1 packets for a single burst
+ *		according to @pkts and @repeat, repeate the burst multiple
+ *		times; 1: distribute the (bMaxBurst+1)*(Mult+1) packets
+ *		according to @pkts and @repeat. normal mode is used by
+ *		default
+ */
+struct mu3h_sch_ep_info {
+	u32 esit;
+	u32 num_budget_microframes;
+	u32 bw_cost_per_microframe;
+	struct list_head endpoint;
+	void *ep;
+	/*
+	 * mtk xHCI scheduling information put into reserved DWs
+	 * in ep context
+	 */
+	u32 offset;
+	u32 repeat;
+	u32 pkts;
+	u32 cs_count;
+	u32 burst_mode;
+};
+
+#define MU3C_U3_PORT_MAX 4
+#define MU3C_U2_PORT_MAX 5
+
+/**
+ * struct mu3c_ippc_regs: MTK ssusb ip port control registers
+ * @ip_pw_ctr0~3: ip power and clock control registers
+ * @ip_pw_sts1~2: ip power and clock status registers
+ * @ip_xhci_cap: ip xHCI capability register
+ * @u3_ctrl_p[x]: ip usb3 port x control register, only low 4bytes are used
+ * @u2_ctrl_p[x]: ip usb2 port x control register, only low 4bytes are used
+ * @u2_phy_pll: usb2 phy pll control register
+ */
+struct mu3c_ippc_regs {
+	__le32 ip_pw_ctr0;
+	__le32 ip_pw_ctr1;
+	__le32 ip_pw_ctr2;
+	__le32 ip_pw_ctr3;
+	__le32 ip_pw_sts1;
+	__le32 ip_pw_sts2;
+	__le32 reserved0[3];
+	__le32 ip_xhci_cap;
+	__le32 reserved1[2];
+	__le64 u3_ctrl_p[MU3C_U3_PORT_MAX];
+	__le64 u2_ctrl_p[MU3C_U2_PORT_MAX];
+	__le32 reserved2;
+	__le32 u2_phy_pll;
+	__le32 reserved3[33]; /* 0x80 ~ 0xff */
+};
+
+struct xhci_hcd_mtk {
+	struct device *dev;
+	struct usb_hcd *hcd;
+	struct mu3h_sch_bw_info *sch_array;
+	struct mu3c_ippc_regs __iomem *ippc_regs;
+	int num_u2_ports;
+	int num_u3_ports;
+	struct regulator *vusb33;
+	struct regulator *vbus;
+	struct clk *sys_clk;	/* sys and mac clock */
+	struct clk *wk_deb_p0;	/* port0's wakeup debounce clock */
+	struct clk *wk_deb_p1;
+	struct regmap *pericfg;
+	int wakeup_src;
+	struct phy **phys;
+	int num_phys;
+};
+
+#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
+int xhci_mtk_sch_init(struct xhci_hcd *xhci);
+void xhci_mtk_sch_exit(struct xhci_hcd *xhci);
+int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+
+#else
+static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
+	struct usb_device *udev, struct usb_host_endpoint *ep)
+{
+	return 0;
+}
+
+static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
+	struct usb_device *udev, struct usb_host_endpoint *ep)
+{
+}
+
+#endif
+
+#endif		/* _XHCI_MTK_H_ */
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 57f40a1..243f696 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -68,6 +68,7 @@
 #include <linux/slab.h>
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 /*
  * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
@@ -3044,18 +3045,27 @@ static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
 			      struct urb *urb, unsigned int num_trbs_left)
 {
 	u32 maxp, total_packet_count;
+	u32 skip_current_trb = 0;
 
-	if (xhci->hci_version < 0x100)
-		return ((td_total_len - transferred) >> 10);
-
-	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
+	if (xhci->hci_version < 0x100) {
+		/* for MTK xHCI, TD size doesn't include this TRB */
+		if (xhci->quirks & XHCI_MTK_HOST)
+			skip_current_trb = 1;
+		else
+			return ((td_total_len - transferred) >> 10);
+	}
 
 	/* One TRB with a zero-length data packet. */
 	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
 	    trb_buff_len == td_total_len)
 		return 0;
 
+	if (skip_current_trb)
+		trb_buff_len = 0;
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
+
 	/* Queueing functions don't count the current TRB into transferred */
 	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
@@ -3443,7 +3453,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		field |= 0x1;
 
 	/* xHCI 1.0 6.4.1.2.1: Transfer Type field */
-	if (xhci->hci_version == 0x100) {
+	if ((xhci->hci_version == 0x100) || (xhci->quirks & XHCI_MTK_HOST)) {
 		if (urb->transfer_buffer_length > 0) {
 			if (setup->bRequestType & USB_DIR_IN)
 				field |= TRB_TX_TYPE(TRB_DATA_IN);
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 6b0f4a4..4741188 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -31,6 +31,7 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 #define DRIVER_AUTHOR "Sarah Sharp"
 #define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
@@ -623,7 +624,11 @@ int xhci_run(struct usb_hcd *hcd)
 			"// Set the interrupt modulation register");
 	temp = readl(&xhci->ir_set->irq_control);
 	temp &= ~ER_IRQ_INTERVAL_MASK;
-	temp |= (u32) 160;
+	/*
+	 * the increment interval is 8 times as much as that defined
+	 * in xHCI spec on MTK's controller
+	 */
+	temp |= (u32) ((xhci->quirks & XHCI_MTK_HOST) ? 20 : 160);
 	writel(temp, &xhci->ir_set->irq_control);
 
 	/* Set the HCD state before we enable the irqs */
@@ -1693,6 +1698,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
+	if (xhci->quirks & XHCI_MTK_HOST)
+		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
+
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1788,6 +1796,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
+	if (xhci->quirks & XHCI_MTK_HOST) {
+		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
+		if (ret < 0) {
+			xhci_free_or_cache_endpoint_ring(xhci,
+				virt_dev, ep_index);
+			return ret;
+		}
+	}
+
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index ea8b904..1536da0 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1577,6 +1577,7 @@ struct xhci_hcd {
 /* For controllers with a broken beyond repair streams implementation */
 #define XHCI_BROKEN_STREAMS	(1 << 19)
 #define XHCI_PME_STUCK_QUIRK	(1 << 20)
+#define XHCI_MTK_HOST		(1 << 21)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */
-- 
1.8.1.1.dirty

[PATCH v8 4/5] xhci: mediatek: support MTK xHCI host controller

[Chunfeng Yun]

There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
  to minimize the scheduling effort for synchronous and
  interrupt endpoints. The parameters are put into reseved
  DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
  8 times as much as that defined in xHCI spec.
3. Its TDS in  Normal TRB defines a number of packets that
  remains to be transferred for a TD after processing all
  Max packets in all previous TRBs.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/usb/host/Kconfig        |   9 +
 drivers/usb/host/Makefile       |   4 +
 drivers/usb/host/xhci-mtk-sch.c | 419 ++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.c     | 744 ++++++++++++++++++++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h     | 156 +++++++++
 drivers/usb/host/xhci-ring.c    |  22 +-
 drivers/usb/host/xhci.c         |  19 +-
 drivers/usb/host/xhci.h         |   1 +
 8 files changed, 1367 insertions(+), 7 deletions(-)
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 079991e..4674118 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -41,6 +41,15 @@ config USB_XHCI_PLATFORM
 
 	  If unsure, say N.
 
+config USB_XHCI_MTK
+	tristate "xHCI support for Mediatek MT65xx"
+	select MFD_SYSCON
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	---help---
+	  Say 'Y' to enable the support for the xHCI host controller
+	  found in Mediatek MT65xx SoCs.
+	  If unsure, say N.
+
 config USB_XHCI_MVEBU
 	tristate "xHCI support for Marvell Armada 375/38x"
 	select USB_XHCI_PLATFORM
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 754efaa..00401f9 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -13,6 +13,9 @@ fhci-$(CONFIG_FHCI_DEBUG) += fhci-dbg.o
 xhci-hcd-y := xhci.o xhci-mem.o
 xhci-hcd-y += xhci-ring.o xhci-hub.o xhci-dbg.o
 xhci-hcd-y += xhci-trace.o
+ifneq ($(CONFIG_USB_XHCI_MTK), )
+	xhci-hcd-y += xhci-mtk-sch.o
+endif
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -30,6 +33,7 @@ endif
 
 obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
new file mode 100644
index 0000000..534d089
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -0,0 +1,419 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Zhigang.Wei <zhigang.wei@mediatek.com>
+ *  Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include "xhci.h"
+#include "xhci-mtk.h"
+
+#define SS_BW_BOUNDARY	51000
+/* table 5-5. High-speed Isoc Transaction Limits in usb_20 spec */
+#define HS_BW_BOUNDARY	6144
+/* usb2 spec section11.18.1: at most 188 FS bytes per microframe */
+#define FS_PAYLOAD_MAX 188
+
+/* mtk scheduler bitmasks */
+#define EP_BPKTS(p)	((p) & 0x3f)
+#define EP_BCSCOUNT(p)	(((p) & 0x7) << 8)
+#define EP_BBM(p)	((p) << 11)
+#define EP_BOFFSET(p)	((p) & 0x3fff)
+#define EP_BREPEAT(p)	(((p) & 0x7fff) << 16)
+
+static int is_fs_or_ls(enum usb_device_speed speed)
+{
+	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
+}
+
+/*
+* get the index of bandwidth domains array which @ep belongs to.
+*
+* the bandwidth domain array is saved to @sch_array of struct xhci_hcd_mtk,
+* each HS root port is treated as a single bandwidth domain,
+* but each SS root port is treated as two bandwidth domains, one for IN eps,
+* one for OUT eps.
+* @real_port value is defined as follow according to xHCI spec:
+* 1 for SSport0, ..., N+1 for SSportN, N+2 for HSport0, N+3 for HSport1, etc
+* so the bandwidth domain array is organized as follow for simplification:
+* SSport0-OUT, SSport0-IN, ..., SSportX-OUT, SSportX-IN, HSport0, ..., HSportY
+*/
+static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
+	struct usb_host_endpoint *ep)
+{
+	struct xhci_virt_device *virt_dev;
+	int bw_index;
+
+	virt_dev = xhci->devs[udev->slot_id];
+
+	if (udev->speed == USB_SPEED_SUPER) {
+		if (usb_endpoint_dir_out(&ep->desc))
+			bw_index = (virt_dev->real_port - 1) * 2;
+		else
+			bw_index = (virt_dev->real_port - 1) * 2 + 1;
+	} else {
+		/* add one more for each SS port */
+		bw_index = virt_dev->real_port + xhci->num_usb3_ports - 1;
+	}
+
+	return bw_index;
+}
+
+static void setup_sch_info(struct usb_device *udev,
+		struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 ep_type;
+	u32 ep_interval;
+	u32 max_packet_size;
+	u32 max_burst;
+	u32 mult;
+	u32 esit_pkts;
+
+	ep_type = CTX_TO_EP_TYPE(le32_to_cpu(ep_ctx->ep_info2));
+	ep_interval = CTX_TO_EP_INTERVAL(le32_to_cpu(ep_ctx->ep_info));
+	max_packet_size = MAX_PACKET_DECODED(le32_to_cpu(ep_ctx->ep_info2));
+	max_burst = CTX_TO_MAX_BURST(le32_to_cpu(ep_ctx->ep_info2));
+	mult = CTX_TO_EP_MULT(le32_to_cpu(ep_ctx->ep_info));
+
+	sch_ep->esit = 1 << ep_interval;
+	sch_ep->offset = 0;
+	sch_ep->burst_mode = 0;
+
+	if (udev->speed == USB_SPEED_HIGH) {
+		sch_ep->cs_count = 0;
+
+		/*
+		 * usb_20 spec section5.9
+		 * a single microframe is enough for HS synchromous endpoints
+		 * in a interval
+		 */
+		sch_ep->num_budget_microframes = 1;
+		sch_ep->repeat = 0;
+
+		/*
+		 * xHCI spec section6.2.3.4
+		 * @max_burst is the number of additional transactions
+		 * opportunities per microframe
+		 */
+		sch_ep->pkts = max_burst + 1;
+		sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
+	} else if (udev->speed == USB_SPEED_SUPER) {
+		/* usb3_r1 spec section4.4.7 & 4.4.8 */
+		sch_ep->cs_count = 0;
+		esit_pkts = (mult + 1) * (max_burst + 1);
+		if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
+			sch_ep->pkts = esit_pkts;
+			sch_ep->num_budget_microframes = 1;
+			sch_ep->repeat = 0;
+		}
+
+		if (ep_type == ISOC_IN_EP || ep_type == ISOC_OUT_EP) {
+			if (esit_pkts <= sch_ep->esit)
+				sch_ep->pkts = 1;
+			else
+				sch_ep->pkts = roundup_pow_of_two(esit_pkts)
+					/ sch_ep->esit;
+
+			sch_ep->num_budget_microframes =
+				DIV_ROUND_UP(esit_pkts, sch_ep->pkts);
+
+			if (sch_ep->num_budget_microframes > 1)
+				sch_ep->repeat = 1;
+			else
+				sch_ep->repeat = 0;
+		}
+		sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
+	} else if (is_fs_or_ls(udev->speed)) {
+
+		/*
+		 * usb_20 spec section11.18.4
+		 * assume worst cases
+		 */
+		sch_ep->repeat = 0;
+		sch_ep->pkts = 1; /* at most one packet for each microframe */
+		if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
+			sch_ep->cs_count = 3; /* at most need 3 CS*/
+			/* one for SS and one for budgeted transaction */
+			sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
+			sch_ep->bw_cost_per_microframe = max_packet_size;
+		}
+		if (ep_type == ISOC_OUT_EP) {
+			/* must never schedule a cs ISOC OUT ep */
+			sch_ep->cs_count = 0;
+
+			/*
+			 * the best case FS budget assumes that 188 FS bytes
+			 * occur in each microframe
+			 */
+			sch_ep->num_budget_microframes = DIV_ROUND_UP(
+				max_packet_size, FS_PAYLOAD_MAX);
+			sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
+		}
+		if (ep_type == ISOC_IN_EP) {
+			/* at most need additional two CS. */
+			sch_ep->cs_count = DIV_ROUND_UP(
+				max_packet_size, FS_PAYLOAD_MAX) + 2;
+			sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
+			sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
+		}
+	}
+}
+
+/* Get maximum bandwidth when we schedule at offset slot. */
+static u32 get_max_bw(struct mu3h_sch_bw_info *sch_bw,
+	struct mu3h_sch_ep_info *sch_ep, u32 offset)
+{
+	u32 num_esit;
+	u32 max_bw = 0;
+	int i;
+	int j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		u32 base = offset + i * sch_ep->esit;
+
+		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
+			if (sch_bw->bus_bw[base + j] > max_bw)
+				max_bw = sch_bw->bus_bw[base + j];
+		}
+	}
+	return max_bw;
+}
+
+static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
+	struct mu3h_sch_ep_info *sch_ep, int bw_cost)
+{
+	u32 num_esit;
+	u32 base;
+	int i;
+	int j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		base = sch_ep->offset + i * sch_ep->esit;
+		for (j = 0; j < sch_ep->num_budget_microframes; j++)
+			sch_bw->bus_bw[base + j] += bw_cost;
+	}
+}
+
+static int check_sch_bw(struct usb_device *udev,
+	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 offset;
+	u32 esit;
+	u32 num_budget_microframes;
+	u32 min_bw;
+	u32 min_index;
+	u32 worst_bw;
+	u32 bw_boundary;
+
+	if (sch_ep->esit > XHCI_MTK_MAX_ESIT)
+		sch_ep->esit = XHCI_MTK_MAX_ESIT;
+
+	esit = sch_ep->esit;
+	num_budget_microframes = sch_ep->num_budget_microframes;
+
+	/*
+	 * Search through all possible schedule microframes.
+	 * and find a microframe where its worst bandwidth is minimum.
+	 */
+	min_bw = ~0;
+	min_index = 0;
+	for (offset = 0; offset < esit; offset++) {
+		if ((offset + num_budget_microframes) > sch_ep->esit)
+			break;
+
+		/*
+		 * usb_20 spec section11.18:
+		 * must never schedule Start-Split in Y6
+		 */
+		if (is_fs_or_ls(udev->speed) && (offset % 8 == 6))
+			continue;
+
+		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
+		if (min_bw > worst_bw) {
+			min_bw = worst_bw;
+			min_index = offset;
+		}
+		if (min_bw == 0)
+			break;
+	}
+	sch_ep->offset = min_index;
+
+	bw_boundary = (udev->speed == USB_SPEED_SUPER)
+				? SS_BW_BOUNDARY : HS_BW_BOUNDARY;
+
+	/* check bandwidth */
+	if (min_bw + sch_ep->bw_cost_per_microframe > bw_boundary)
+		return -ERANGE;
+
+	/* update bus bandwidth info */
+	update_bus_bw(sch_bw, sch_ep, sch_ep->bw_cost_per_microframe);
+
+	return 0;
+}
+
+static bool need_bw_sch(struct usb_host_endpoint *ep,
+	enum usb_device_speed speed, int has_tt)
+{
+	/* only for periodic endpoints */
+	if (usb_endpoint_xfer_control(&ep->desc)
+		|| usb_endpoint_xfer_bulk(&ep->desc))
+		return false;
+
+	/*
+	 * for LS & FS periodic endpoints which its device don't attach
+	 * to TT are also ignored, root-hub will schedule them directly
+	 */
+	if (is_fs_or_ls(speed) && !has_tt)
+		return false;
+
+	return true;
+}
+
+int xhci_mtk_sch_init(struct xhci_hcd *xhci)
+{
+	struct usb_hcd *hcd = xhci_to_hcd(xhci);
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+	struct mu3h_sch_bw_info *sch_array;
+	int num_usb_bus;
+	int i;
+
+	/* ss IN and OUT are separated */
+	num_usb_bus = xhci->num_usb3_ports * 2 + xhci->num_usb2_ports;
+
+	sch_array = kcalloc(num_usb_bus, sizeof(*sch_array), GFP_KERNEL);
+	if (sch_array == NULL)
+		return -ENOMEM;
+
+	for (i = 0; i < num_usb_bus; i++)
+		INIT_LIST_HEAD(&sch_array[i].bw_ep_list);
+
+	mtk->sch_array = sch_array;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_sch_init);
+
+void xhci_mtk_sch_exit(struct xhci_hcd *xhci)
+{
+	struct usb_hcd *hcd = xhci_to_hcd(xhci);
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	kfree(mtk->sch_array);
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_sch_exit);
+
+int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	int ret = 0;
+	int bw_index;
+	struct xhci_hcd *xhci;
+	unsigned int ep_index;
+	struct xhci_ep_ctx *ep_ctx;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_virt_device *virt_dev;
+	struct mu3h_sch_bw_info *sch_bw;
+	struct mu3h_sch_ep_info *sch_ep;
+	struct mu3h_sch_bw_info *sch_array;
+
+	xhci = hcd_to_xhci(hcd);
+	virt_dev = xhci->devs[udev->slot_id];
+	ep_index = xhci_get_endpoint_index(&ep->desc);
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
+	sch_array = mtk->sch_array;
+
+	xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
+		usb_endpoint_type(&ep->desc), udev->speed, ep);
+
+	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+		return 0;
+
+	bw_index = get_bw_index(xhci, udev, ep);
+	sch_bw = &sch_array[bw_index];
+
+	sch_ep = kzalloc(sizeof(struct mu3h_sch_ep_info), GFP_NOIO);
+	if (!sch_ep)
+		return -ENOMEM;
+
+	setup_sch_info(udev, ep_ctx, sch_ep);
+
+	ret = check_sch_bw(udev, sch_bw, sch_ep);
+	if (ret) {
+		xhci_err(xhci, "Not enough bandwidth!\n");
+		kfree(sch_ep);
+		return -ENOSPC;
+	}
+
+	list_add_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
+	sch_ep->ep = ep;
+
+	ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
+		| EP_BCSCOUNT(sch_ep->cs_count) | EP_BBM(sch_ep->burst_mode));
+	ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
+		| EP_BREPEAT(sch_ep->repeat));
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
+
+void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	int bw_index;
+	struct xhci_hcd *xhci;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_virt_device *virt_dev;
+	struct mu3h_sch_bw_info *sch_array;
+	struct mu3h_sch_bw_info *sch_bw;
+	struct mu3h_sch_ep_info *sch_ep;
+
+	xhci = hcd_to_xhci(hcd);
+	virt_dev = xhci->devs[udev->slot_id];
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	sch_array = mtk->sch_array;
+
+	xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
+		usb_endpoint_type(&ep->desc), udev->speed, ep);
+
+	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+		return;
+
+	bw_index = get_bw_index(xhci, udev, ep);
+	sch_bw = &sch_array[bw_index];
+
+	list_for_each_entry(sch_ep, &sch_bw->bw_ep_list, endpoint) {
+		if (sch_ep->ep == ep) {
+			update_bus_bw(sch_bw, sch_ep,
+				-sch_ep->bw_cost_per_microframe);
+			list_del(&sch_ep->endpoint);
+			kfree(sch_ep);
+			break;
+		}
+	}
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
new file mode 100644
index 0000000..4510fef
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk.c
@@ -0,0 +1,744 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/usb/phy.h>
+#include <linux/usb/xhci_pdriver.h>
+
+#include "xhci.h"
+#include "xhci-mtk.h"
+
+/* ip_pw_ctrl0 register */
+#define CTRL0_IP_SW_RST	BIT(0)
+
+/* ip_pw_ctrl1 register */
+#define CTRL1_IP_HOST_PDN	BIT(0)
+
+/* ip_pw_ctrl2 register */
+#define CTRL2_IP_DEV_PDN	BIT(0)
+
+/* ip_pw_sts1 register */
+#define STS1_IP_SLEEP_STS	BIT(30)
+#define STS1_U3_MAC_RST	BIT(16)
+#define STS1_SYS125_RST	BIT(10)
+#define STS1_REF_RST		BIT(8)
+#define STS1_SYSPLL_STABLE	BIT(0)
+
+/* ip_pw_sts2 register */
+#define STS2_U2_MAC_RST	BIT(0)
+
+/* ip_xhci_cap register */
+#define CAP_U3_PORT_NUM(p)	((p) & 0xff)
+#define CAP_U2_PORT_NUM(p)	(((p) >> 8) & 0xff)
+
+/* u3_ctrl_p register */
+#define CTRL_U3_PORT_HOST_SEL	BIT(2)
+#define CTRL_U3_PORT_PDN	BIT(1)
+#define CTRL_U3_PORT_DIS	BIT(0)
+
+/* u2_ctrl_p register */
+#define CTRL_U2_PORT_HOST_SEL	BIT(2)
+#define CTRL_U2_PORT_PDN	BIT(1)
+#define CTRL_U2_PORT_DIS	BIT(0)
+
+/* u2_phy_pll register */
+#define CTRL_U2_FORCE_PLL_STB	BIT(28)
+
+#define PERI_WK_CTRL0		0x400
+#define UWK_CTR0_0P_LS_PE	BIT(8)  /* posedge */
+#define UWK_CTR0_0P_LS_NE	BIT(7)  /* negedge for 0p linestate*/
+#define UWK_CTL1_1P_LS_C(x)	(((x) & 0xf) << 1)
+#define UWK_CTL1_1P_LS_E	BIT(0)
+
+#define PERI_WK_CTRL1		0x404
+#define UWK_CTL1_IS_C(x)	(((x) & 0xf) << 26)
+#define UWK_CTL1_IS_E		BIT(25)
+#define UWK_CTL1_0P_LS_C(x)	(((x) & 0xf) << 21)
+#define UWK_CTL1_0P_LS_E	BIT(20)
+#define UWK_CTL1_IDDIG_C(x)	(((x) & 0xf) << 11)  /* cycle debounce */
+#define UWK_CTL1_IDDIG_E	BIT(10) /* enable debounce */
+#define UWK_CTL1_IDDIG_P	BIT(9)  /* polarity */
+#define UWK_CTL1_0P_LS_P	BIT(7)
+#define UWK_CTL1_IS_P		BIT(6)  /* polarity for ip sleep */
+
+enum ssusb_wakeup_src {
+	SSUSB_WK_IP_SLEEP = 1,
+	SSUSB_WK_LINE_STATE = 2,
+};
+
+static int check_ip_clk_status(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 val, check_val;
+	int ret;
+
+	check_val = STS1_SYSPLL_STABLE | STS1_REF_RST | STS1_SYS125_RST;
+	check_val |= (mtk->num_u3_ports ? STS1_U3_MAC_RST : 0);
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts1, val,
+			  (check_val == (val & check_val)), 100, 20000);
+	if (ret) {
+		dev_err(mtk->dev, "mac3 clocks are not stable (0x%x)\n", val);
+		return ret;
+	}
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts2, val,
+			   (val & STS2_U2_MAC_RST), 100, 10000);
+	if (ret) {
+		dev_err(mtk->dev, "mac2 reset is still active!!!\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xhci_mtk_ports_enable(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+	int i;
+
+	/* power on host ip */
+	temp = readl(&ippc->ip_pw_ctr1);
+	temp &= ~CTRL1_IP_HOST_PDN;
+	writel(temp, &ippc->ip_pw_ctr1);
+
+	/* power on and enable all u3 ports */
+	for (i = 0; i < mtk->num_u3_ports; i++) {
+		temp = readl(&ippc->u3_ctrl_p[i]);
+		temp &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS);
+		temp |= CTRL_U3_PORT_HOST_SEL;
+		writel(temp, &ippc->u3_ctrl_p[i]);
+	}
+
+	/* power on and enable all u2 ports */
+	for (i = 0; i < mtk->num_u2_ports; i++) {
+		temp = readl(&ippc->u2_ctrl_p[i]);
+		temp &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS);
+		temp |= CTRL_U2_PORT_HOST_SEL;
+		writel(temp, &ippc->u2_ctrl_p[i]);
+	}
+
+	/*
+	 * wait for clocks to be stable, and clock domains reset to
+	 * be inactive after power on and enable ports
+	 */
+	return check_ip_clk_status(mtk);
+}
+
+static int xhci_mtk_ports_disable(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+	int ret;
+	int i;
+
+	/* power down all u3 ports */
+	for (i = 0; i < mtk->num_u3_ports; i++) {
+		temp = readl(&ippc->u3_ctrl_p[i]);
+		temp |= CTRL_U3_PORT_PDN;
+		writel(temp, &ippc->u3_ctrl_p[i]);
+	}
+
+	/* power down all u2 ports */
+	for (i = 0; i < mtk->num_u2_ports; i++) {
+		temp = readl(&ippc->u2_ctrl_p[i]);
+		temp |= CTRL_U2_PORT_PDN;
+		writel(temp, &ippc->u2_ctrl_p[i]);
+	}
+
+	/* power down host ip */
+	temp = readl(&ippc->ip_pw_ctr1);
+	temp |= CTRL1_IP_HOST_PDN;
+	writel(temp, &ippc->ip_pw_ctr1);
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts1, temp,
+			  (temp & STS1_IP_SLEEP_STS), 100, 100000);
+	if (ret) {
+		dev_err(mtk->dev, "ip sleep failed!!!\n");
+		return ret;
+	}
+	return 0;
+}
+
+static void xhci_mtk_ports_config(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+
+	/* reset whole ip */
+	temp = readl(&ippc->ip_pw_ctr0);
+	temp |= CTRL0_IP_SW_RST;
+	writel(temp, &ippc->ip_pw_ctr0);
+	udelay(1);
+	temp = readl(&ippc->ip_pw_ctr0);
+	temp &= ~CTRL0_IP_SW_RST;
+	writel(temp, &ippc->ip_pw_ctr0);
+
+	/*
+	 * device ip is default power-on in fact
+	 * power down device ip, otherwise ip-sleep will fail
+	 */
+	temp = readl(&ippc->ip_pw_ctr2);
+	temp |= CTRL2_IP_DEV_PDN;
+	writel(temp, &ippc->ip_pw_ctr2);
+
+	temp = readl(&ippc->ip_xhci_cap);
+	mtk->num_u3_ports = CAP_U3_PORT_NUM(temp);
+	mtk->num_u2_ports = CAP_U2_PORT_NUM(temp);
+	dev_dbg(mtk->dev, "%s u2p:%d, u3p:%d\n", __func__,
+			mtk->num_u2_ports, mtk->num_u3_ports);
+
+	xhci_mtk_ports_enable(mtk);
+}
+
+static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk)
+{
+	int ret;
+
+	ret = clk_prepare_enable(mtk->sys_clk);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable u3phya_ref\n");
+		goto u3phya_ref_err;
+	}
+	ret = clk_prepare_enable(mtk->wk_deb_p0);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable wk_deb_p0\n");
+		goto usb_p0_err;
+	}
+	if (mtk->num_phys > 1) {
+		ret = clk_prepare_enable(mtk->wk_deb_p1);
+		if (ret) {
+			dev_err(mtk->dev, "failed to enable wk_deb_p1\n");
+			goto usb_p1_err;
+		}
+	}
+	return 0;
+
+usb_p1_err:
+	clk_disable_unprepare(mtk->wk_deb_p0);
+usb_p0_err:
+	clk_disable_unprepare(mtk->sys_clk);
+u3phya_ref_err:
+	return -EINVAL;
+}
+
+static void xhci_mtk_clks_disable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->num_phys > 1)
+		clk_disable_unprepare(mtk->wk_deb_p1);
+	clk_disable_unprepare(mtk->wk_deb_p0);
+	clk_disable_unprepare(mtk->sys_clk);
+}
+
+/* only clocks can be turn off for ip-sleep wakeup mode */
+static void usb_wakeup_ip_sleep_en(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_IS_P;
+	tmp &= ~(UWK_CTL1_IS_C(0xf));
+	tmp |= UWK_CTL1_IS_C(0x8);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_IS_E);
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	dev_dbg(mtk->dev, "%s(): WK_CTRL1[P6,E25,C26:29]=%#x\n",
+		__func__, tmp);
+}
+
+static void usb_wakeup_ip_sleep_dis(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+
+	regmap_read(mtk->pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_IS_E;
+	regmap_write(mtk->pericfg, PERI_WK_CTRL1, tmp);
+}
+
+/*
+* for line-state wakeup mode, phy's power should not power-down
+* and only support cable plug in/out
+*/
+static void usb_wakeup_line_state_en(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	/* line-state of u2-port0 */
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_0P_LS_P;
+	tmp &= ~(UWK_CTL1_0P_LS_C(0xf));
+	tmp |= UWK_CTL1_0P_LS_C(0x8);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_0P_LS_E);
+
+	/* line-state of u2-port1 if support */
+	if (mtk->num_phys > 1) {
+		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
+		tmp &= ~(UWK_CTL1_1P_LS_C(0xf));
+		tmp |= UWK_CTL1_1P_LS_C(0x8);
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp | UWK_CTL1_1P_LS_E);
+	}
+}
+
+static void usb_wakeup_line_state_dis(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_0P_LS_E;
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+
+	if (mtk->num_phys > 1) {
+		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
+		tmp &= ~UWK_CTL1_1P_LS_E;
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
+	}
+}
+
+static void usb_wakeup_enable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->wakeup_src == SSUSB_WK_IP_SLEEP)
+		usb_wakeup_ip_sleep_en(mtk);
+	else if (mtk->wakeup_src == SSUSB_WK_LINE_STATE)
+		usb_wakeup_line_state_en(mtk);
+}
+
+static void usb_wakeup_disable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->wakeup_src == SSUSB_WK_IP_SLEEP)
+		usb_wakeup_ip_sleep_dis(mtk);
+	else if (mtk->wakeup_src == SSUSB_WK_LINE_STATE)
+		usb_wakeup_line_state_dis(mtk);
+}
+
+static int usb_wakeup_of_property_parse(struct xhci_hcd_mtk *mtk,
+				struct device_node *dn)
+{
+	struct device *dev = mtk->dev;
+
+	/*
+	* wakeup function is optional, so it is not an error if this property
+	* does not exist, and in such case, no need to get relative
+	* properties anymore.
+	*/
+	of_property_read_u32(dn, "mediatek,wakeup-src", &mtk->wakeup_src);
+	if (!mtk->wakeup_src)
+		return 0;
+
+	mtk->wk_deb_p0 = devm_clk_get(dev, "wakeup_deb_p0");
+	if (IS_ERR(mtk->wk_deb_p0)) {
+		dev_err(dev, "fail to get wakeup_deb_p0\n");
+		return PTR_ERR(mtk->wk_deb_p0);
+	}
+
+	mtk->wk_deb_p1 = devm_clk_get(dev, "wakeup_deb_p1");
+	if (IS_ERR(mtk->wk_deb_p1)) {
+		dev_err(dev, "fail to get wakeup_deb_p1\n");
+		return PTR_ERR(mtk->wk_deb_p1);
+	}
+
+	mtk->pericfg = syscon_regmap_lookup_by_phandle(dn,
+						"mediatek,syscon-wakeup");
+	if (IS_ERR(mtk->pericfg)) {
+		dev_err(dev, "fail to get pericfg regs\n");
+		return PTR_ERR(mtk->pericfg);
+	}
+
+	return 0;
+}
+
+static int xhci_mtk_setup(struct usb_hcd *hcd);
+static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
+	.extra_priv_size = sizeof(struct xhci_hcd),
+	.reset = xhci_mtk_setup,
+};
+
+static struct hc_driver __read_mostly xhci_mtk_hc_driver;
+
+static int xhci_mtk_phy_enable(struct xhci_hcd_mtk *mtk)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < mtk->num_phys; i++) {
+		ret = phy_init(mtk->phys[i]);
+		if (ret)
+			goto disable_phy;
+		ret = phy_power_on(mtk->phys[i]);
+		if (ret) {
+			phy_exit(mtk->phys[i]);
+			goto disable_phy;
+		}
+	}
+	return 0;
+
+disable_phy:
+	for (; i > 0; i--) {
+		phy_power_off(mtk->phys[i - 1]);
+		phy_exit(mtk->phys[i - 1]);
+	}
+	return ret;
+}
+
+static void xhci_mtk_phy_disable(struct xhci_hcd_mtk *mtk)
+{
+	unsigned int i;
+
+	for (i = 0; i < mtk->num_phys; i++) {
+		phy_power_off(mtk->phys[i]);
+		phy_exit(mtk->phys[i]);
+	}
+}
+
+static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
+{
+	int ret;
+
+	ret = regulator_enable(mtk->vbus);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable vbus\n");
+		return ret;
+	}
+
+	ret = regulator_enable(mtk->vusb33);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable vusb33\n");
+		regulator_disable(mtk->vbus);
+		return ret;
+	}
+	return 0;
+}
+
+static void xhci_mtk_ldos_disable(struct xhci_hcd_mtk *mtk)
+{
+	regulator_disable(mtk->vbus);
+	regulator_disable(mtk->vusb33);
+}
+
+static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci)
+{
+	/*
+	 * As of now platform drivers don't provide MSI support so we ensure
+	 * here that the generic code does not try to make a pci_dev from our
+	 * dev struct in order to setup MSI
+	 */
+	xhci->quirks |= XHCI_PLAT;
+	xhci->quirks |= XHCI_MTK_HOST;
+	/*
+	 * MTK host controller gives a spurious successful event after a
+	 * short transfer. Ignore it.
+	 */
+	xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
+}
+
+/* called during probe() after chip reset completes */
+static int xhci_mtk_setup(struct usb_hcd *hcd)
+{
+	struct xhci_hcd *xhci;
+	int ret;
+
+	ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
+	if (ret)
+		return ret;
+
+	if (!usb_hcd_is_primary_hcd(hcd))
+		return 0;
+
+	xhci = hcd_to_xhci(hcd);
+	return xhci_mtk_sch_init(xhci);
+}
+
+
+static int xhci_mtk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct usb_xhci_pdata *pdata = dev_get_platdata(dev);
+	struct xhci_hcd_mtk *mtk;
+	const struct hc_driver *driver;
+	struct xhci_hcd *xhci;
+	struct resource *res;
+	struct usb_hcd *hcd;
+	struct phy *phy;
+	int phy_num;
+	int ret = -ENODEV;
+	int irq;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	driver = &xhci_mtk_hc_driver;
+	mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL);
+	if (!mtk)
+		return -ENOMEM;
+
+	mtk->dev = dev;
+	mtk->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(mtk->vbus)) {
+		dev_err(dev, "fail to get vbus\n");
+		return PTR_ERR(mtk->vbus);
+	}
+
+	mtk->vusb33 = devm_regulator_get(dev, "vusb33");
+	if (IS_ERR(mtk->vusb33)) {
+		dev_err(dev, "fail to get vusb33\n");
+		return PTR_ERR(mtk->vusb33);
+	}
+
+	mtk->sys_clk = devm_clk_get(dev, "sys_ck");
+	if (IS_ERR(mtk->sys_clk)) {
+		dev_err(dev, "fail to get sys_ck\n");
+		return PTR_ERR(mtk->sys_clk);
+	}
+
+	ret = usb_wakeup_of_property_parse(mtk, node);
+	if (ret)
+		return ret;
+
+	mtk->num_phys = of_count_phandle_with_args(node,
+			"phys", "#phy-cells");
+	if (mtk->num_phys > 0) {
+		mtk->phys = devm_kcalloc(dev, mtk->num_phys,
+					sizeof(*mtk->phys), GFP_KERNEL);
+		if (!mtk->phys)
+			return -ENOMEM;
+	} else {
+		mtk->num_phys = 0;
+	}
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	ret = xhci_mtk_ldos_enable(mtk);
+	if (ret)
+		goto disable_pm;
+
+	ret = xhci_mtk_clks_enable(mtk);
+	if (ret)
+		goto disable_ldos;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		goto disable_clk;
+
+	/* Initialize dma_mask and coherent_dma_mask to 32-bits */
+	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	if (ret)
+		goto disable_clk;
+
+	if (!dev->dma_mask)
+		dev->dma_mask = &dev->coherent_dma_mask;
+	else
+		dma_set_mask(dev, DMA_BIT_MASK(32));
+
+	hcd = usb_create_hcd(driver, dev, dev_name(dev));
+	if (!hcd) {
+		ret = -ENOMEM;
+		goto disable_clk;
+	}
+
+	/*
+	 * USB 2.0 roothub is stored in the platform_device.
+	 * Swap it with mtk HCD.
+	 */
+	mtk->hcd = platform_get_drvdata(pdev);
+	platform_set_drvdata(pdev, mtk);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hcd->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(hcd->regs)) {
+		ret = PTR_ERR(hcd->regs);
+		goto put_usb2_hcd;
+	}
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	mtk->ippc_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(mtk->ippc_regs)) {
+		ret = PTR_ERR(mtk->ippc_regs);
+		goto put_usb2_hcd;
+	}
+
+	for (phy_num = 0; phy_num < mtk->num_phys; phy_num++) {
+		phy = devm_of_phy_get_by_index(dev, node, phy_num);
+		if (IS_ERR(phy)) {
+			ret = PTR_ERR(phy);
+			goto put_usb2_hcd;
+		}
+		mtk->phys[phy_num] = phy;
+	}
+
+	xhci_mtk_ports_config(mtk);
+	xhci_mtk_phy_enable(mtk);
+	device_init_wakeup(dev, 1);
+
+	xhci = hcd_to_xhci(hcd);
+	xhci->main_hcd = hcd;
+	xhci->shared_hcd = usb_create_shared_hcd(driver, dev,
+			dev_name(dev), hcd);
+	if (!xhci->shared_hcd) {
+		ret = -ENOMEM;
+		goto disable_usb_phy;
+	}
+
+	if ((node && of_property_read_bool(node, "usb3-lpm-capable")) ||
+			(pdata && pdata->usb3_lpm_capable))
+		xhci->quirks |= XHCI_LPM_SUPPORT;
+
+	if (HCC_MAX_PSA(xhci->hcc_params) >= 4)
+		xhci->shared_hcd->can_do_streams = 1;
+
+	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto put_usb3_hcd;
+
+	ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto dealloc_usb2_hcd;
+
+	return 0;
+
+dealloc_usb2_hcd:
+	xhci_mtk_sch_exit(xhci);
+	usb_remove_hcd(hcd);
+
+put_usb3_hcd:
+	usb_put_hcd(xhci->shared_hcd);
+
+disable_usb_phy:
+	xhci_mtk_phy_disable(mtk);
+	device_init_wakeup(dev, 0);
+
+put_usb2_hcd:
+	usb_put_hcd(hcd);
+
+disable_clk:
+	xhci_mtk_clks_disable(mtk);
+
+disable_ldos:
+	xhci_mtk_ldos_disable(mtk);
+
+disable_pm:
+	pm_runtime_put_sync(dev);
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int xhci_mtk_remove(struct platform_device *dev)
+{
+	struct xhci_hcd_mtk *mtk = platform_get_drvdata(dev);
+	struct usb_hcd	*hcd = mtk->hcd;
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+
+	usb_remove_hcd(xhci->shared_hcd);
+	xhci_mtk_phy_disable(mtk);
+	device_init_wakeup(&dev->dev, 0);
+
+	usb_remove_hcd(hcd);
+	usb_put_hcd(xhci->shared_hcd);
+	usb_put_hcd(hcd);
+	xhci_mtk_sch_exit(xhci);
+	xhci_mtk_clks_disable(mtk);
+	xhci_mtk_ldos_disable(mtk);
+	pm_runtime_put_sync(&dev->dev);
+	pm_runtime_disable(&dev->dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int xhci_mtk_suspend(struct device *dev)
+{
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	xhci_mtk_ports_disable(mtk);
+	xhci_mtk_phy_disable(mtk);
+	xhci_mtk_clks_disable(mtk);
+	usb_wakeup_enable(mtk);
+	return 0;
+}
+
+static int xhci_mtk_resume(struct device *dev)
+{
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	usb_wakeup_disable(mtk);
+	xhci_mtk_clks_enable(mtk);
+	xhci_mtk_phy_enable(mtk);
+	xhci_mtk_ports_enable(mtk);
+	return 0;
+}
+
+static const struct dev_pm_ops xhci_mtk_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xhci_mtk_suspend, xhci_mtk_resume)
+};
+#define DEV_PM_OPS	(&xhci_mtk_pm_ops)
+#else
+#define DEV_PM_OPS	NULL
+#endif /* CONFIG_PM */
+
+#ifdef CONFIG_OF
+static const struct of_device_id mtk_xhci_of_match[] = {
+	{ .compatible = "mediatek,mt8173-xhci"},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mtk_xhci_of_match);
+#endif
+
+static struct platform_driver mtk_xhci_driver = {
+	.probe	= xhci_mtk_probe,
+	.remove	= xhci_mtk_remove,
+	.driver	= {
+		.name = "xhci-mtk",
+		.pm = DEV_PM_OPS,
+		.of_match_table = of_match_ptr(mtk_xhci_of_match),
+	},
+};
+
+static int __init xhci_mtk_init(void)
+{
+	xhci_init_driver(&xhci_mtk_hc_driver, &xhci_mtk_overrides);
+	return platform_driver_register(&mtk_xhci_driver);
+}
+module_init(xhci_mtk_init);
+
+static void __exit xhci_mtk_exit(void)
+{
+	platform_driver_unregister(&mtk_xhci_driver);
+}
+module_exit(xhci_mtk_exit);
+
+MODULE_DESCRIPTION("MediaTek xHCI Host Controller Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
new file mode 100644
index 0000000..8913c2f
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk.h
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Zhigang.Wei <zhigang.wei@mediatek.com>
+ *  Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _XHCI_MTK_H_
+#define _XHCI_MTK_H_
+
+#include "xhci.h"
+
+/**
+ * To simplify scheduler algorithm, set a upper limit for ESIT,
+ * if a synchromous ep's ESIT is larger than @XHCI_MTK_MAX_ESIT,
+ * round down to the limit value, that means allocating more
+ * bandwidth to it.
+ */
+#define XHCI_MTK_MAX_ESIT	64
+
+/**
+ * struct mu3h_sch_bw_info: schedule information for bandwidth domain
+ *
+ * @bus_bw: array to keep track of bandwidth already used at each uframes
+ * @bw_ep_list: eps in the bandwidth domain
+ *
+ * treat a HS root port as a bandwidth domain, but treat a SS root port as
+ * two bandwidth domains, one for IN eps and another for OUT eps.
+ */
+struct mu3h_sch_bw_info {
+	u32 bus_bw[XHCI_MTK_MAX_ESIT];
+	struct list_head bw_ep_list;
+};
+
+/**
+ * struct mu3h_sch_ep_info: schedule information for endpoint
+ *
+ * @esit: unit is 125us, equal to 2 << Interval field in ep-context
+ * @num_budget_microframes: number of continuous uframes
+ *		(@repeat==1) scheduled within the interval
+ * @bw_cost_per_microframe: bandwidth cost per microframe
+ * @endpoint: linked into bandwidth domain which it belongs to
+ * @ep: address of usb_host_endpoint struct
+ * @offset: which uframe of the interval that transfer should be
+ *		scheduled first time within the interval
+ * @repeat: the time gap between two uframes that transfers are
+ *		scheduled within a interval. in the simple algorithm, only
+ *		assign 0 or 1 to it; 0 means using only one uframe in a
+ *		interval, and 1 means using @num_budget_microframes
+ *		continuous uframes
+ * @pkts: number of packets to be transferred in the scheduled uframes
+ * @cs_count: number of CS that host will trigger
+ * @burst_mode: burst mode for scheduling. 0: normal burst mode,
+ *		distribute the bMaxBurst+1 packets for a single burst
+ *		according to @pkts and @repeat, repeate the burst multiple
+ *		times; 1: distribute the (bMaxBurst+1)*(Mult+1) packets
+ *		according to @pkts and @repeat. normal mode is used by
+ *		default
+ */
+struct mu3h_sch_ep_info {
+	u32 esit;
+	u32 num_budget_microframes;
+	u32 bw_cost_per_microframe;
+	struct list_head endpoint;
+	void *ep;
+	/*
+	 * mtk xHCI scheduling information put into reserved DWs
+	 * in ep context
+	 */
+	u32 offset;
+	u32 repeat;
+	u32 pkts;
+	u32 cs_count;
+	u32 burst_mode;
+};
+
+#define MU3C_U3_PORT_MAX 4
+#define MU3C_U2_PORT_MAX 5
+
+/**
+ * struct mu3c_ippc_regs: MTK ssusb ip port control registers
+ * @ip_pw_ctr0~3: ip power and clock control registers
+ * @ip_pw_sts1~2: ip power and clock status registers
+ * @ip_xhci_cap: ip xHCI capability register
+ * @u3_ctrl_p[x]: ip usb3 port x control register, only low 4bytes are used
+ * @u2_ctrl_p[x]: ip usb2 port x control register, only low 4bytes are used
+ * @u2_phy_pll: usb2 phy pll control register
+ */
+struct mu3c_ippc_regs {
+	__le32 ip_pw_ctr0;
+	__le32 ip_pw_ctr1;
+	__le32 ip_pw_ctr2;
+	__le32 ip_pw_ctr3;
+	__le32 ip_pw_sts1;
+	__le32 ip_pw_sts2;
+	__le32 reserved0[3];
+	__le32 ip_xhci_cap;
+	__le32 reserved1[2];
+	__le64 u3_ctrl_p[MU3C_U3_PORT_MAX];
+	__le64 u2_ctrl_p[MU3C_U2_PORT_MAX];
+	__le32 reserved2;
+	__le32 u2_phy_pll;
+	__le32 reserved3[33]; /* 0x80 ~ 0xff */
+};
+
+struct xhci_hcd_mtk {
+	struct device *dev;
+	struct usb_hcd *hcd;
+	struct mu3h_sch_bw_info *sch_array;
+	struct mu3c_ippc_regs __iomem *ippc_regs;
+	int num_u2_ports;
+	int num_u3_ports;
+	struct regulator *vusb33;
+	struct regulator *vbus;
+	struct clk *sys_clk;	/* sys and mac clock */
+	struct clk *wk_deb_p0;	/* port0's wakeup debounce clock */
+	struct clk *wk_deb_p1;
+	struct regmap *pericfg;
+	int wakeup_src;
+	struct phy **phys;
+	int num_phys;
+};
+
+#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
+int xhci_mtk_sch_init(struct xhci_hcd *xhci);
+void xhci_mtk_sch_exit(struct xhci_hcd *xhci);
+int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+
+#else
+static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
+	struct usb_device *udev, struct usb_host_endpoint *ep)
+{
+	return 0;
+}
+
+static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
+	struct usb_device *udev, struct usb_host_endpoint *ep)
+{
+}
+
+#endif
+
+#endif		/* _XHCI_MTK_H_ */
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 57f40a1..243f696 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -68,6 +68,7 @@
 #include <linux/slab.h>
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 /*
  * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
@@ -3044,18 +3045,27 @@ static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
 			      struct urb *urb, unsigned int num_trbs_left)
 {
 	u32 maxp, total_packet_count;
+	u32 skip_current_trb = 0;
 
-	if (xhci->hci_version < 0x100)
-		return ((td_total_len - transferred) >> 10);
-
-	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
+	if (xhci->hci_version < 0x100) {
+		/* for MTK xHCI, TD size doesn't include this TRB */
+		if (xhci->quirks & XHCI_MTK_HOST)
+			skip_current_trb = 1;
+		else
+			return ((td_total_len - transferred) >> 10);
+	}
 
 	/* One TRB with a zero-length data packet. */
 	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
 	    trb_buff_len == td_total_len)
 		return 0;
 
+	if (skip_current_trb)
+		trb_buff_len = 0;
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
+
 	/* Queueing functions don't count the current TRB into transferred */
 	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
@@ -3443,7 +3453,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		field |= 0x1;
 
 	/* xHCI 1.0 6.4.1.2.1: Transfer Type field */
-	if (xhci->hci_version == 0x100) {
+	if ((xhci->hci_version == 0x100) || (xhci->quirks & XHCI_MTK_HOST)) {
 		if (urb->transfer_buffer_length > 0) {
 			if (setup->bRequestType & USB_DIR_IN)
 				field |= TRB_TX_TYPE(TRB_DATA_IN);
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 6b0f4a4..4741188 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -31,6 +31,7 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 #define DRIVER_AUTHOR "Sarah Sharp"
 #define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
@@ -623,7 +624,11 @@ int xhci_run(struct usb_hcd *hcd)
 			"// Set the interrupt modulation register");
 	temp = readl(&xhci->ir_set->irq_control);
 	temp &= ~ER_IRQ_INTERVAL_MASK;
-	temp |= (u32) 160;
+	/*
+	 * the increment interval is 8 times as much as that defined
+	 * in xHCI spec on MTK's controller
+	 */
+	temp |= (u32) ((xhci->quirks & XHCI_MTK_HOST) ? 20 : 160);
 	writel(temp, &xhci->ir_set->irq_control);
 
 	/* Set the HCD state before we enable the irqs */
@@ -1693,6 +1698,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
+	if (xhci->quirks & XHCI_MTK_HOST)
+		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
+
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1788,6 +1796,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
+	if (xhci->quirks & XHCI_MTK_HOST) {
+		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
+		if (ret < 0) {
+			xhci_free_or_cache_endpoint_ring(xhci,
+				virt_dev, ep_index);
+			return ret;
+		}
+	}
+
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index ea8b904..1536da0 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1577,6 +1577,7 @@ struct xhci_hcd {
 /* For controllers with a broken beyond repair streams implementation */
 #define XHCI_BROKEN_STREAMS	(1 << 19)
 #define XHCI_PME_STUCK_QUIRK	(1 << 20)
+#define XHCI_MTK_HOST		(1 << 21)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */
-- 
1.8.1.1.dirty

[PATCH v8 4/5] xhci: mediatek: support MTK xHCI host controller

[Chunfeng Yun]

There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
  to minimize the scheduling effort for synchronous and
  interrupt endpoints. The parameters are put into reseved
  DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
  8 times as much as that defined in xHCI spec.
3. Its TDS in  Normal TRB defines a number of packets that
  remains to be transferred for a TD after processing all
  Max packets in all previous TRBs.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 drivers/usb/host/Kconfig        |   9 +
 drivers/usb/host/Makefile       |   4 +
 drivers/usb/host/xhci-mtk-sch.c | 419 ++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.c     | 744 ++++++++++++++++++++++++++++++++++++++++
 drivers/usb/host/xhci-mtk.h     | 156 +++++++++
 drivers/usb/host/xhci-ring.c    |  22 +-
 drivers/usb/host/xhci.c         |  19 +-
 drivers/usb/host/xhci.h         |   1 +
 8 files changed, 1367 insertions(+), 7 deletions(-)
 create mode 100644 drivers/usb/host/xhci-mtk-sch.c
 create mode 100644 drivers/usb/host/xhci-mtk.c
 create mode 100644 drivers/usb/host/xhci-mtk.h

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 079991e..4674118 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -41,6 +41,15 @@ config USB_XHCI_PLATFORM
 
 	  If unsure, say N.
 
+config USB_XHCI_MTK
+	tristate "xHCI support for Mediatek MT65xx"
+	select MFD_SYSCON
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	---help---
+	  Say 'Y' to enable the support for the xHCI host controller
+	  found in Mediatek MT65xx SoCs.
+	  If unsure, say N.
+
 config USB_XHCI_MVEBU
 	tristate "xHCI support for Marvell Armada 375/38x"
 	select USB_XHCI_PLATFORM
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 754efaa..00401f9 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -13,6 +13,9 @@ fhci-$(CONFIG_FHCI_DEBUG) += fhci-dbg.o
 xhci-hcd-y := xhci.o xhci-mem.o
 xhci-hcd-y += xhci-ring.o xhci-hub.o xhci-dbg.o
 xhci-hcd-y += xhci-trace.o
+ifneq ($(CONFIG_USB_XHCI_MTK), )
+	xhci-hcd-y += xhci-mtk-sch.o
+endif
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -30,6 +33,7 @@ endif
 
 obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
new file mode 100644
index 0000000..534d089
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -0,0 +1,419 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Zhigang.Wei <zhigang.wei@mediatek.com>
+ *  Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include "xhci.h"
+#include "xhci-mtk.h"
+
+#define SS_BW_BOUNDARY	51000
+/* table 5-5. High-speed Isoc Transaction Limits in usb_20 spec */
+#define HS_BW_BOUNDARY	6144
+/* usb2 spec section11.18.1: at most 188 FS bytes per microframe */
+#define FS_PAYLOAD_MAX 188
+
+/* mtk scheduler bitmasks */
+#define EP_BPKTS(p)	((p) & 0x3f)
+#define EP_BCSCOUNT(p)	(((p) & 0x7) << 8)
+#define EP_BBM(p)	((p) << 11)
+#define EP_BOFFSET(p)	((p) & 0x3fff)
+#define EP_BREPEAT(p)	(((p) & 0x7fff) << 16)
+
+static int is_fs_or_ls(enum usb_device_speed speed)
+{
+	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
+}
+
+/*
+* get the index of bandwidth domains array which @ep belongs to.
+*
+* the bandwidth domain array is saved to @sch_array of struct xhci_hcd_mtk,
+* each HS root port is treated as a single bandwidth domain,
+* but each SS root port is treated as two bandwidth domains, one for IN eps,
+* one for OUT eps.
+* @real_port value is defined as follow according to xHCI spec:
+* 1 for SSport0, ..., N+1 for SSportN, N+2 for HSport0, N+3 for HSport1, etc
+* so the bandwidth domain array is organized as follow for simplification:
+* SSport0-OUT, SSport0-IN, ..., SSportX-OUT, SSportX-IN, HSport0, ..., HSportY
+*/
+static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
+	struct usb_host_endpoint *ep)
+{
+	struct xhci_virt_device *virt_dev;
+	int bw_index;
+
+	virt_dev = xhci->devs[udev->slot_id];
+
+	if (udev->speed == USB_SPEED_SUPER) {
+		if (usb_endpoint_dir_out(&ep->desc))
+			bw_index = (virt_dev->real_port - 1) * 2;
+		else
+			bw_index = (virt_dev->real_port - 1) * 2 + 1;
+	} else {
+		/* add one more for each SS port */
+		bw_index = virt_dev->real_port + xhci->num_usb3_ports - 1;
+	}
+
+	return bw_index;
+}
+
+static void setup_sch_info(struct usb_device *udev,
+		struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 ep_type;
+	u32 ep_interval;
+	u32 max_packet_size;
+	u32 max_burst;
+	u32 mult;
+	u32 esit_pkts;
+
+	ep_type = CTX_TO_EP_TYPE(le32_to_cpu(ep_ctx->ep_info2));
+	ep_interval = CTX_TO_EP_INTERVAL(le32_to_cpu(ep_ctx->ep_info));
+	max_packet_size = MAX_PACKET_DECODED(le32_to_cpu(ep_ctx->ep_info2));
+	max_burst = CTX_TO_MAX_BURST(le32_to_cpu(ep_ctx->ep_info2));
+	mult = CTX_TO_EP_MULT(le32_to_cpu(ep_ctx->ep_info));
+
+	sch_ep->esit = 1 << ep_interval;
+	sch_ep->offset = 0;
+	sch_ep->burst_mode = 0;
+
+	if (udev->speed == USB_SPEED_HIGH) {
+		sch_ep->cs_count = 0;
+
+		/*
+		 * usb_20 spec section5.9
+		 * a single microframe is enough for HS synchromous endpoints
+		 * in a interval
+		 */
+		sch_ep->num_budget_microframes = 1;
+		sch_ep->repeat = 0;
+
+		/*
+		 * xHCI spec section6.2.3.4
+		 * @max_burst is the number of additional transactions
+		 * opportunities per microframe
+		 */
+		sch_ep->pkts = max_burst + 1;
+		sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
+	} else if (udev->speed == USB_SPEED_SUPER) {
+		/* usb3_r1 spec section4.4.7 & 4.4.8 */
+		sch_ep->cs_count = 0;
+		esit_pkts = (mult + 1) * (max_burst + 1);
+		if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
+			sch_ep->pkts = esit_pkts;
+			sch_ep->num_budget_microframes = 1;
+			sch_ep->repeat = 0;
+		}
+
+		if (ep_type == ISOC_IN_EP || ep_type == ISOC_OUT_EP) {
+			if (esit_pkts <= sch_ep->esit)
+				sch_ep->pkts = 1;
+			else
+				sch_ep->pkts = roundup_pow_of_two(esit_pkts)
+					/ sch_ep->esit;
+
+			sch_ep->num_budget_microframes =
+				DIV_ROUND_UP(esit_pkts, sch_ep->pkts);
+
+			if (sch_ep->num_budget_microframes > 1)
+				sch_ep->repeat = 1;
+			else
+				sch_ep->repeat = 0;
+		}
+		sch_ep->bw_cost_per_microframe = max_packet_size * sch_ep->pkts;
+	} else if (is_fs_or_ls(udev->speed)) {
+
+		/*
+		 * usb_20 spec section11.18.4
+		 * assume worst cases
+		 */
+		sch_ep->repeat = 0;
+		sch_ep->pkts = 1; /* at most one packet for each microframe */
+		if (ep_type == INT_IN_EP || ep_type == INT_OUT_EP) {
+			sch_ep->cs_count = 3; /* at most need 3 CS*/
+			/* one for SS and one for budgeted transaction */
+			sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
+			sch_ep->bw_cost_per_microframe = max_packet_size;
+		}
+		if (ep_type == ISOC_OUT_EP) {
+			/* must never schedule a cs ISOC OUT ep */
+			sch_ep->cs_count = 0;
+
+			/*
+			 * the best case FS budget assumes that 188 FS bytes
+			 * occur in each microframe
+			 */
+			sch_ep->num_budget_microframes = DIV_ROUND_UP(
+				max_packet_size, FS_PAYLOAD_MAX);
+			sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
+		}
+		if (ep_type == ISOC_IN_EP) {
+			/* at most need additional two CS. */
+			sch_ep->cs_count = DIV_ROUND_UP(
+				max_packet_size, FS_PAYLOAD_MAX) + 2;
+			sch_ep->num_budget_microframes = sch_ep->cs_count + 2;
+			sch_ep->bw_cost_per_microframe = FS_PAYLOAD_MAX;
+		}
+	}
+}
+
+/* Get maximum bandwidth when we schedule at offset slot. */
+static u32 get_max_bw(struct mu3h_sch_bw_info *sch_bw,
+	struct mu3h_sch_ep_info *sch_ep, u32 offset)
+{
+	u32 num_esit;
+	u32 max_bw = 0;
+	int i;
+	int j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		u32 base = offset + i * sch_ep->esit;
+
+		for (j = 0; j < sch_ep->num_budget_microframes; j++) {
+			if (sch_bw->bus_bw[base + j] > max_bw)
+				max_bw = sch_bw->bus_bw[base + j];
+		}
+	}
+	return max_bw;
+}
+
+static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
+	struct mu3h_sch_ep_info *sch_ep, int bw_cost)
+{
+	u32 num_esit;
+	u32 base;
+	int i;
+	int j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		base = sch_ep->offset + i * sch_ep->esit;
+		for (j = 0; j < sch_ep->num_budget_microframes; j++)
+			sch_bw->bus_bw[base + j] += bw_cost;
+	}
+}
+
+static int check_sch_bw(struct usb_device *udev,
+	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 offset;
+	u32 esit;
+	u32 num_budget_microframes;
+	u32 min_bw;
+	u32 min_index;
+	u32 worst_bw;
+	u32 bw_boundary;
+
+	if (sch_ep->esit > XHCI_MTK_MAX_ESIT)
+		sch_ep->esit = XHCI_MTK_MAX_ESIT;
+
+	esit = sch_ep->esit;
+	num_budget_microframes = sch_ep->num_budget_microframes;
+
+	/*
+	 * Search through all possible schedule microframes.
+	 * and find a microframe where its worst bandwidth is minimum.
+	 */
+	min_bw = ~0;
+	min_index = 0;
+	for (offset = 0; offset < esit; offset++) {
+		if ((offset + num_budget_microframes) > sch_ep->esit)
+			break;
+
+		/*
+		 * usb_20 spec section11.18:
+		 * must never schedule Start-Split in Y6
+		 */
+		if (is_fs_or_ls(udev->speed) && (offset % 8 == 6))
+			continue;
+
+		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
+		if (min_bw > worst_bw) {
+			min_bw = worst_bw;
+			min_index = offset;
+		}
+		if (min_bw == 0)
+			break;
+	}
+	sch_ep->offset = min_index;
+
+	bw_boundary = (udev->speed == USB_SPEED_SUPER)
+				? SS_BW_BOUNDARY : HS_BW_BOUNDARY;
+
+	/* check bandwidth */
+	if (min_bw + sch_ep->bw_cost_per_microframe > bw_boundary)
+		return -ERANGE;
+
+	/* update bus bandwidth info */
+	update_bus_bw(sch_bw, sch_ep, sch_ep->bw_cost_per_microframe);
+
+	return 0;
+}
+
+static bool need_bw_sch(struct usb_host_endpoint *ep,
+	enum usb_device_speed speed, int has_tt)
+{
+	/* only for periodic endpoints */
+	if (usb_endpoint_xfer_control(&ep->desc)
+		|| usb_endpoint_xfer_bulk(&ep->desc))
+		return false;
+
+	/*
+	 * for LS & FS periodic endpoints which its device don't attach
+	 * to TT are also ignored, root-hub will schedule them directly
+	 */
+	if (is_fs_or_ls(speed) && !has_tt)
+		return false;
+
+	return true;
+}
+
+int xhci_mtk_sch_init(struct xhci_hcd *xhci)
+{
+	struct usb_hcd *hcd = xhci_to_hcd(xhci);
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+	struct mu3h_sch_bw_info *sch_array;
+	int num_usb_bus;
+	int i;
+
+	/* ss IN and OUT are separated */
+	num_usb_bus = xhci->num_usb3_ports * 2 + xhci->num_usb2_ports;
+
+	sch_array = kcalloc(num_usb_bus, sizeof(*sch_array), GFP_KERNEL);
+	if (sch_array == NULL)
+		return -ENOMEM;
+
+	for (i = 0; i < num_usb_bus; i++)
+		INIT_LIST_HEAD(&sch_array[i].bw_ep_list);
+
+	mtk->sch_array = sch_array;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_sch_init);
+
+void xhci_mtk_sch_exit(struct xhci_hcd *xhci)
+{
+	struct usb_hcd *hcd = xhci_to_hcd(xhci);
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	kfree(mtk->sch_array);
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_sch_exit);
+
+int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	int ret = 0;
+	int bw_index;
+	struct xhci_hcd *xhci;
+	unsigned int ep_index;
+	struct xhci_ep_ctx *ep_ctx;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_virt_device *virt_dev;
+	struct mu3h_sch_bw_info *sch_bw;
+	struct mu3h_sch_ep_info *sch_ep;
+	struct mu3h_sch_bw_info *sch_array;
+
+	xhci = hcd_to_xhci(hcd);
+	virt_dev = xhci->devs[udev->slot_id];
+	ep_index = xhci_get_endpoint_index(&ep->desc);
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
+	sch_array = mtk->sch_array;
+
+	xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
+		usb_endpoint_type(&ep->desc), udev->speed, ep);
+
+	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+		return 0;
+
+	bw_index = get_bw_index(xhci, udev, ep);
+	sch_bw = &sch_array[bw_index];
+
+	sch_ep = kzalloc(sizeof(struct mu3h_sch_ep_info), GFP_NOIO);
+	if (!sch_ep)
+		return -ENOMEM;
+
+	setup_sch_info(udev, ep_ctx, sch_ep);
+
+	ret = check_sch_bw(udev, sch_bw, sch_ep);
+	if (ret) {
+		xhci_err(xhci, "Not enough bandwidth!\n");
+		kfree(sch_ep);
+		return -ENOSPC;
+	}
+
+	list_add_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
+	sch_ep->ep = ep;
+
+	ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
+		| EP_BCSCOUNT(sch_ep->cs_count) | EP_BBM(sch_ep->burst_mode));
+	ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
+		| EP_BREPEAT(sch_ep->repeat));
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
+
+void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct device *dev = hcd->self.controller;
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	int bw_index;
+	struct xhci_hcd *xhci;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_virt_device *virt_dev;
+	struct mu3h_sch_bw_info *sch_array;
+	struct mu3h_sch_bw_info *sch_bw;
+	struct mu3h_sch_ep_info *sch_ep;
+
+	xhci = hcd_to_xhci(hcd);
+	virt_dev = xhci->devs[udev->slot_id];
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	sch_array = mtk->sch_array;
+
+	xhci_dbg(xhci, "%s() xfer_type: %d, speed:%d, ep:%p\n", __func__,
+		usb_endpoint_type(&ep->desc), udev->speed, ep);
+
+	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+		return;
+
+	bw_index = get_bw_index(xhci, udev, ep);
+	sch_bw = &sch_array[bw_index];
+
+	list_for_each_entry(sch_ep, &sch_bw->bw_ep_list, endpoint) {
+		if (sch_ep->ep == ep) {
+			update_bus_bw(sch_bw, sch_ep,
+				-sch_ep->bw_cost_per_microframe);
+			list_del(&sch_ep->endpoint);
+			kfree(sch_ep);
+			break;
+		}
+	}
+}
+EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
new file mode 100644
index 0000000..4510fef
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk.c
@@ -0,0 +1,744 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/usb/phy.h>
+#include <linux/usb/xhci_pdriver.h>
+
+#include "xhci.h"
+#include "xhci-mtk.h"
+
+/* ip_pw_ctrl0 register */
+#define CTRL0_IP_SW_RST	BIT(0)
+
+/* ip_pw_ctrl1 register */
+#define CTRL1_IP_HOST_PDN	BIT(0)
+
+/* ip_pw_ctrl2 register */
+#define CTRL2_IP_DEV_PDN	BIT(0)
+
+/* ip_pw_sts1 register */
+#define STS1_IP_SLEEP_STS	BIT(30)
+#define STS1_U3_MAC_RST	BIT(16)
+#define STS1_SYS125_RST	BIT(10)
+#define STS1_REF_RST		BIT(8)
+#define STS1_SYSPLL_STABLE	BIT(0)
+
+/* ip_pw_sts2 register */
+#define STS2_U2_MAC_RST	BIT(0)
+
+/* ip_xhci_cap register */
+#define CAP_U3_PORT_NUM(p)	((p) & 0xff)
+#define CAP_U2_PORT_NUM(p)	(((p) >> 8) & 0xff)
+
+/* u3_ctrl_p register */
+#define CTRL_U3_PORT_HOST_SEL	BIT(2)
+#define CTRL_U3_PORT_PDN	BIT(1)
+#define CTRL_U3_PORT_DIS	BIT(0)
+
+/* u2_ctrl_p register */
+#define CTRL_U2_PORT_HOST_SEL	BIT(2)
+#define CTRL_U2_PORT_PDN	BIT(1)
+#define CTRL_U2_PORT_DIS	BIT(0)
+
+/* u2_phy_pll register */
+#define CTRL_U2_FORCE_PLL_STB	BIT(28)
+
+#define PERI_WK_CTRL0		0x400
+#define UWK_CTR0_0P_LS_PE	BIT(8)  /* posedge */
+#define UWK_CTR0_0P_LS_NE	BIT(7)  /* negedge for 0p linestate*/
+#define UWK_CTL1_1P_LS_C(x)	(((x) & 0xf) << 1)
+#define UWK_CTL1_1P_LS_E	BIT(0)
+
+#define PERI_WK_CTRL1		0x404
+#define UWK_CTL1_IS_C(x)	(((x) & 0xf) << 26)
+#define UWK_CTL1_IS_E		BIT(25)
+#define UWK_CTL1_0P_LS_C(x)	(((x) & 0xf) << 21)
+#define UWK_CTL1_0P_LS_E	BIT(20)
+#define UWK_CTL1_IDDIG_C(x)	(((x) & 0xf) << 11)  /* cycle debounce */
+#define UWK_CTL1_IDDIG_E	BIT(10) /* enable debounce */
+#define UWK_CTL1_IDDIG_P	BIT(9)  /* polarity */
+#define UWK_CTL1_0P_LS_P	BIT(7)
+#define UWK_CTL1_IS_P		BIT(6)  /* polarity for ip sleep */
+
+enum ssusb_wakeup_src {
+	SSUSB_WK_IP_SLEEP = 1,
+	SSUSB_WK_LINE_STATE = 2,
+};
+
+static int check_ip_clk_status(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 val, check_val;
+	int ret;
+
+	check_val = STS1_SYSPLL_STABLE | STS1_REF_RST | STS1_SYS125_RST;
+	check_val |= (mtk->num_u3_ports ? STS1_U3_MAC_RST : 0);
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts1, val,
+			  (check_val == (val & check_val)), 100, 20000);
+	if (ret) {
+		dev_err(mtk->dev, "mac3 clocks are not stable (0x%x)\n", val);
+		return ret;
+	}
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts2, val,
+			   (val & STS2_U2_MAC_RST), 100, 10000);
+	if (ret) {
+		dev_err(mtk->dev, "mac2 reset is still active!!!\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int xhci_mtk_ports_enable(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+	int i;
+
+	/* power on host ip */
+	temp = readl(&ippc->ip_pw_ctr1);
+	temp &= ~CTRL1_IP_HOST_PDN;
+	writel(temp, &ippc->ip_pw_ctr1);
+
+	/* power on and enable all u3 ports */
+	for (i = 0; i < mtk->num_u3_ports; i++) {
+		temp = readl(&ippc->u3_ctrl_p[i]);
+		temp &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS);
+		temp |= CTRL_U3_PORT_HOST_SEL;
+		writel(temp, &ippc->u3_ctrl_p[i]);
+	}
+
+	/* power on and enable all u2 ports */
+	for (i = 0; i < mtk->num_u2_ports; i++) {
+		temp = readl(&ippc->u2_ctrl_p[i]);
+		temp &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS);
+		temp |= CTRL_U2_PORT_HOST_SEL;
+		writel(temp, &ippc->u2_ctrl_p[i]);
+	}
+
+	/*
+	 * wait for clocks to be stable, and clock domains reset to
+	 * be inactive after power on and enable ports
+	 */
+	return check_ip_clk_status(mtk);
+}
+
+static int xhci_mtk_ports_disable(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+	int ret;
+	int i;
+
+	/* power down all u3 ports */
+	for (i = 0; i < mtk->num_u3_ports; i++) {
+		temp = readl(&ippc->u3_ctrl_p[i]);
+		temp |= CTRL_U3_PORT_PDN;
+		writel(temp, &ippc->u3_ctrl_p[i]);
+	}
+
+	/* power down all u2 ports */
+	for (i = 0; i < mtk->num_u2_ports; i++) {
+		temp = readl(&ippc->u2_ctrl_p[i]);
+		temp |= CTRL_U2_PORT_PDN;
+		writel(temp, &ippc->u2_ctrl_p[i]);
+	}
+
+	/* power down host ip */
+	temp = readl(&ippc->ip_pw_ctr1);
+	temp |= CTRL1_IP_HOST_PDN;
+	writel(temp, &ippc->ip_pw_ctr1);
+
+	ret = readl_poll_timeout(&ippc->ip_pw_sts1, temp,
+			  (temp & STS1_IP_SLEEP_STS), 100, 100000);
+	if (ret) {
+		dev_err(mtk->dev, "ip sleep failed!!!\n");
+		return ret;
+	}
+	return 0;
+}
+
+static void xhci_mtk_ports_config(struct xhci_hcd_mtk *mtk)
+{
+	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
+	u32 temp;
+
+	/* reset whole ip */
+	temp = readl(&ippc->ip_pw_ctr0);
+	temp |= CTRL0_IP_SW_RST;
+	writel(temp, &ippc->ip_pw_ctr0);
+	udelay(1);
+	temp = readl(&ippc->ip_pw_ctr0);
+	temp &= ~CTRL0_IP_SW_RST;
+	writel(temp, &ippc->ip_pw_ctr0);
+
+	/*
+	 * device ip is default power-on in fact
+	 * power down device ip, otherwise ip-sleep will fail
+	 */
+	temp = readl(&ippc->ip_pw_ctr2);
+	temp |= CTRL2_IP_DEV_PDN;
+	writel(temp, &ippc->ip_pw_ctr2);
+
+	temp = readl(&ippc->ip_xhci_cap);
+	mtk->num_u3_ports = CAP_U3_PORT_NUM(temp);
+	mtk->num_u2_ports = CAP_U2_PORT_NUM(temp);
+	dev_dbg(mtk->dev, "%s u2p:%d, u3p:%d\n", __func__,
+			mtk->num_u2_ports, mtk->num_u3_ports);
+
+	xhci_mtk_ports_enable(mtk);
+}
+
+static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk)
+{
+	int ret;
+
+	ret = clk_prepare_enable(mtk->sys_clk);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable u3phya_ref\n");
+		goto u3phya_ref_err;
+	}
+	ret = clk_prepare_enable(mtk->wk_deb_p0);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable wk_deb_p0\n");
+		goto usb_p0_err;
+	}
+	if (mtk->num_phys > 1) {
+		ret = clk_prepare_enable(mtk->wk_deb_p1);
+		if (ret) {
+			dev_err(mtk->dev, "failed to enable wk_deb_p1\n");
+			goto usb_p1_err;
+		}
+	}
+	return 0;
+
+usb_p1_err:
+	clk_disable_unprepare(mtk->wk_deb_p0);
+usb_p0_err:
+	clk_disable_unprepare(mtk->sys_clk);
+u3phya_ref_err:
+	return -EINVAL;
+}
+
+static void xhci_mtk_clks_disable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->num_phys > 1)
+		clk_disable_unprepare(mtk->wk_deb_p1);
+	clk_disable_unprepare(mtk->wk_deb_p0);
+	clk_disable_unprepare(mtk->sys_clk);
+}
+
+/* only clocks can be turn off for ip-sleep wakeup mode */
+static void usb_wakeup_ip_sleep_en(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_IS_P;
+	tmp &= ~(UWK_CTL1_IS_C(0xf));
+	tmp |= UWK_CTL1_IS_C(0x8);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_IS_E);
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	dev_dbg(mtk->dev, "%s(): WK_CTRL1[P6,E25,C26:29]=%#x\n",
+		__func__, tmp);
+}
+
+static void usb_wakeup_ip_sleep_dis(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+
+	regmap_read(mtk->pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_IS_E;
+	regmap_write(mtk->pericfg, PERI_WK_CTRL1, tmp);
+}
+
+/*
+* for line-state wakeup mode, phy's power should not power-down
+* and only support cable plug in/out
+*/
+static void usb_wakeup_line_state_en(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	/* line-state of u2-port0 */
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_0P_LS_P;
+	tmp &= ~(UWK_CTL1_0P_LS_C(0xf));
+	tmp |= UWK_CTL1_0P_LS_C(0x8);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_0P_LS_E);
+
+	/* line-state of u2-port1 if support */
+	if (mtk->num_phys > 1) {
+		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
+		tmp &= ~(UWK_CTL1_1P_LS_C(0xf));
+		tmp |= UWK_CTL1_1P_LS_C(0x8);
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp | UWK_CTL1_1P_LS_E);
+	}
+}
+
+static void usb_wakeup_line_state_dis(struct xhci_hcd_mtk *mtk)
+{
+	u32 tmp;
+	struct regmap *pericfg = mtk->pericfg;
+
+	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
+	tmp &= ~UWK_CTL1_0P_LS_E;
+	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
+
+	if (mtk->num_phys > 1) {
+		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
+		tmp &= ~UWK_CTL1_1P_LS_E;
+		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
+	}
+}
+
+static void usb_wakeup_enable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->wakeup_src == SSUSB_WK_IP_SLEEP)
+		usb_wakeup_ip_sleep_en(mtk);
+	else if (mtk->wakeup_src == SSUSB_WK_LINE_STATE)
+		usb_wakeup_line_state_en(mtk);
+}
+
+static void usb_wakeup_disable(struct xhci_hcd_mtk *mtk)
+{
+	if (mtk->wakeup_src == SSUSB_WK_IP_SLEEP)
+		usb_wakeup_ip_sleep_dis(mtk);
+	else if (mtk->wakeup_src == SSUSB_WK_LINE_STATE)
+		usb_wakeup_line_state_dis(mtk);
+}
+
+static int usb_wakeup_of_property_parse(struct xhci_hcd_mtk *mtk,
+				struct device_node *dn)
+{
+	struct device *dev = mtk->dev;
+
+	/*
+	* wakeup function is optional, so it is not an error if this property
+	* does not exist, and in such case, no need to get relative
+	* properties anymore.
+	*/
+	of_property_read_u32(dn, "mediatek,wakeup-src", &mtk->wakeup_src);
+	if (!mtk->wakeup_src)
+		return 0;
+
+	mtk->wk_deb_p0 = devm_clk_get(dev, "wakeup_deb_p0");
+	if (IS_ERR(mtk->wk_deb_p0)) {
+		dev_err(dev, "fail to get wakeup_deb_p0\n");
+		return PTR_ERR(mtk->wk_deb_p0);
+	}
+
+	mtk->wk_deb_p1 = devm_clk_get(dev, "wakeup_deb_p1");
+	if (IS_ERR(mtk->wk_deb_p1)) {
+		dev_err(dev, "fail to get wakeup_deb_p1\n");
+		return PTR_ERR(mtk->wk_deb_p1);
+	}
+
+	mtk->pericfg = syscon_regmap_lookup_by_phandle(dn,
+						"mediatek,syscon-wakeup");
+	if (IS_ERR(mtk->pericfg)) {
+		dev_err(dev, "fail to get pericfg regs\n");
+		return PTR_ERR(mtk->pericfg);
+	}
+
+	return 0;
+}
+
+static int xhci_mtk_setup(struct usb_hcd *hcd);
+static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
+	.extra_priv_size = sizeof(struct xhci_hcd),
+	.reset = xhci_mtk_setup,
+};
+
+static struct hc_driver __read_mostly xhci_mtk_hc_driver;
+
+static int xhci_mtk_phy_enable(struct xhci_hcd_mtk *mtk)
+{
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < mtk->num_phys; i++) {
+		ret = phy_init(mtk->phys[i]);
+		if (ret)
+			goto disable_phy;
+		ret = phy_power_on(mtk->phys[i]);
+		if (ret) {
+			phy_exit(mtk->phys[i]);
+			goto disable_phy;
+		}
+	}
+	return 0;
+
+disable_phy:
+	for (; i > 0; i--) {
+		phy_power_off(mtk->phys[i - 1]);
+		phy_exit(mtk->phys[i - 1]);
+	}
+	return ret;
+}
+
+static void xhci_mtk_phy_disable(struct xhci_hcd_mtk *mtk)
+{
+	unsigned int i;
+
+	for (i = 0; i < mtk->num_phys; i++) {
+		phy_power_off(mtk->phys[i]);
+		phy_exit(mtk->phys[i]);
+	}
+}
+
+static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
+{
+	int ret;
+
+	ret = regulator_enable(mtk->vbus);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable vbus\n");
+		return ret;
+	}
+
+	ret = regulator_enable(mtk->vusb33);
+	if (ret) {
+		dev_err(mtk->dev, "failed to enable vusb33\n");
+		regulator_disable(mtk->vbus);
+		return ret;
+	}
+	return 0;
+}
+
+static void xhci_mtk_ldos_disable(struct xhci_hcd_mtk *mtk)
+{
+	regulator_disable(mtk->vbus);
+	regulator_disable(mtk->vusb33);
+}
+
+static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci)
+{
+	/*
+	 * As of now platform drivers don't provide MSI support so we ensure
+	 * here that the generic code does not try to make a pci_dev from our
+	 * dev struct in order to setup MSI
+	 */
+	xhci->quirks |= XHCI_PLAT;
+	xhci->quirks |= XHCI_MTK_HOST;
+	/*
+	 * MTK host controller gives a spurious successful event after a
+	 * short transfer. Ignore it.
+	 */
+	xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
+}
+
+/* called during probe() after chip reset completes */
+static int xhci_mtk_setup(struct usb_hcd *hcd)
+{
+	struct xhci_hcd *xhci;
+	int ret;
+
+	ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
+	if (ret)
+		return ret;
+
+	if (!usb_hcd_is_primary_hcd(hcd))
+		return 0;
+
+	xhci = hcd_to_xhci(hcd);
+	return xhci_mtk_sch_init(xhci);
+}
+
+
+static int xhci_mtk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct usb_xhci_pdata *pdata = dev_get_platdata(dev);
+	struct xhci_hcd_mtk *mtk;
+	const struct hc_driver *driver;
+	struct xhci_hcd *xhci;
+	struct resource *res;
+	struct usb_hcd *hcd;
+	struct phy *phy;
+	int phy_num;
+	int ret = -ENODEV;
+	int irq;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	driver = &xhci_mtk_hc_driver;
+	mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL);
+	if (!mtk)
+		return -ENOMEM;
+
+	mtk->dev = dev;
+	mtk->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(mtk->vbus)) {
+		dev_err(dev, "fail to get vbus\n");
+		return PTR_ERR(mtk->vbus);
+	}
+
+	mtk->vusb33 = devm_regulator_get(dev, "vusb33");
+	if (IS_ERR(mtk->vusb33)) {
+		dev_err(dev, "fail to get vusb33\n");
+		return PTR_ERR(mtk->vusb33);
+	}
+
+	mtk->sys_clk = devm_clk_get(dev, "sys_ck");
+	if (IS_ERR(mtk->sys_clk)) {
+		dev_err(dev, "fail to get sys_ck\n");
+		return PTR_ERR(mtk->sys_clk);
+	}
+
+	ret = usb_wakeup_of_property_parse(mtk, node);
+	if (ret)
+		return ret;
+
+	mtk->num_phys = of_count_phandle_with_args(node,
+			"phys", "#phy-cells");
+	if (mtk->num_phys > 0) {
+		mtk->phys = devm_kcalloc(dev, mtk->num_phys,
+					sizeof(*mtk->phys), GFP_KERNEL);
+		if (!mtk->phys)
+			return -ENOMEM;
+	} else {
+		mtk->num_phys = 0;
+	}
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	ret = xhci_mtk_ldos_enable(mtk);
+	if (ret)
+		goto disable_pm;
+
+	ret = xhci_mtk_clks_enable(mtk);
+	if (ret)
+		goto disable_ldos;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		goto disable_clk;
+
+	/* Initialize dma_mask and coherent_dma_mask to 32-bits */
+	ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
+	if (ret)
+		goto disable_clk;
+
+	if (!dev->dma_mask)
+		dev->dma_mask = &dev->coherent_dma_mask;
+	else
+		dma_set_mask(dev, DMA_BIT_MASK(32));
+
+	hcd = usb_create_hcd(driver, dev, dev_name(dev));
+	if (!hcd) {
+		ret = -ENOMEM;
+		goto disable_clk;
+	}
+
+	/*
+	 * USB 2.0 roothub is stored in the platform_device.
+	 * Swap it with mtk HCD.
+	 */
+	mtk->hcd = platform_get_drvdata(pdev);
+	platform_set_drvdata(pdev, mtk);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hcd->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(hcd->regs)) {
+		ret = PTR_ERR(hcd->regs);
+		goto put_usb2_hcd;
+	}
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	mtk->ippc_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(mtk->ippc_regs)) {
+		ret = PTR_ERR(mtk->ippc_regs);
+		goto put_usb2_hcd;
+	}
+
+	for (phy_num = 0; phy_num < mtk->num_phys; phy_num++) {
+		phy = devm_of_phy_get_by_index(dev, node, phy_num);
+		if (IS_ERR(phy)) {
+			ret = PTR_ERR(phy);
+			goto put_usb2_hcd;
+		}
+		mtk->phys[phy_num] = phy;
+	}
+
+	xhci_mtk_ports_config(mtk);
+	xhci_mtk_phy_enable(mtk);
+	device_init_wakeup(dev, 1);
+
+	xhci = hcd_to_xhci(hcd);
+	xhci->main_hcd = hcd;
+	xhci->shared_hcd = usb_create_shared_hcd(driver, dev,
+			dev_name(dev), hcd);
+	if (!xhci->shared_hcd) {
+		ret = -ENOMEM;
+		goto disable_usb_phy;
+	}
+
+	if ((node && of_property_read_bool(node, "usb3-lpm-capable")) ||
+			(pdata && pdata->usb3_lpm_capable))
+		xhci->quirks |= XHCI_LPM_SUPPORT;
+
+	if (HCC_MAX_PSA(xhci->hcc_params) >= 4)
+		xhci->shared_hcd->can_do_streams = 1;
+
+	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto put_usb3_hcd;
+
+	ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto dealloc_usb2_hcd;
+
+	return 0;
+
+dealloc_usb2_hcd:
+	xhci_mtk_sch_exit(xhci);
+	usb_remove_hcd(hcd);
+
+put_usb3_hcd:
+	usb_put_hcd(xhci->shared_hcd);
+
+disable_usb_phy:
+	xhci_mtk_phy_disable(mtk);
+	device_init_wakeup(dev, 0);
+
+put_usb2_hcd:
+	usb_put_hcd(hcd);
+
+disable_clk:
+	xhci_mtk_clks_disable(mtk);
+
+disable_ldos:
+	xhci_mtk_ldos_disable(mtk);
+
+disable_pm:
+	pm_runtime_put_sync(dev);
+	pm_runtime_disable(dev);
+	return ret;
+}
+
+static int xhci_mtk_remove(struct platform_device *dev)
+{
+	struct xhci_hcd_mtk *mtk = platform_get_drvdata(dev);
+	struct usb_hcd	*hcd = mtk->hcd;
+	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
+
+	usb_remove_hcd(xhci->shared_hcd);
+	xhci_mtk_phy_disable(mtk);
+	device_init_wakeup(&dev->dev, 0);
+
+	usb_remove_hcd(hcd);
+	usb_put_hcd(xhci->shared_hcd);
+	usb_put_hcd(hcd);
+	xhci_mtk_sch_exit(xhci);
+	xhci_mtk_clks_disable(mtk);
+	xhci_mtk_ldos_disable(mtk);
+	pm_runtime_put_sync(&dev->dev);
+	pm_runtime_disable(&dev->dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int xhci_mtk_suspend(struct device *dev)
+{
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	xhci_mtk_ports_disable(mtk);
+	xhci_mtk_phy_disable(mtk);
+	xhci_mtk_clks_disable(mtk);
+	usb_wakeup_enable(mtk);
+	return 0;
+}
+
+static int xhci_mtk_resume(struct device *dev)
+{
+	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev);
+
+	usb_wakeup_disable(mtk);
+	xhci_mtk_clks_enable(mtk);
+	xhci_mtk_phy_enable(mtk);
+	xhci_mtk_ports_enable(mtk);
+	return 0;
+}
+
+static const struct dev_pm_ops xhci_mtk_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(xhci_mtk_suspend, xhci_mtk_resume)
+};
+#define DEV_PM_OPS	(&xhci_mtk_pm_ops)
+#else
+#define DEV_PM_OPS	NULL
+#endif /* CONFIG_PM */
+
+#ifdef CONFIG_OF
+static const struct of_device_id mtk_xhci_of_match[] = {
+	{ .compatible = "mediatek,mt8173-xhci"},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mtk_xhci_of_match);
+#endif
+
+static struct platform_driver mtk_xhci_driver = {
+	.probe	= xhci_mtk_probe,
+	.remove	= xhci_mtk_remove,
+	.driver	= {
+		.name = "xhci-mtk",
+		.pm = DEV_PM_OPS,
+		.of_match_table = of_match_ptr(mtk_xhci_of_match),
+	},
+};
+
+static int __init xhci_mtk_init(void)
+{
+	xhci_init_driver(&xhci_mtk_hc_driver, &xhci_mtk_overrides);
+	return platform_driver_register(&mtk_xhci_driver);
+}
+module_init(xhci_mtk_init);
+
+static void __exit xhci_mtk_exit(void)
+{
+	platform_driver_unregister(&mtk_xhci_driver);
+}
+module_exit(xhci_mtk_exit);
+
+MODULE_DESCRIPTION("MediaTek xHCI Host Controller Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
new file mode 100644
index 0000000..8913c2f
--- /dev/null
+++ b/drivers/usb/host/xhci-mtk.h
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author:
+ *  Zhigang.Wei <zhigang.wei@mediatek.com>
+ *  Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _XHCI_MTK_H_
+#define _XHCI_MTK_H_
+
+#include "xhci.h"
+
+/**
+ * To simplify scheduler algorithm, set a upper limit for ESIT,
+ * if a synchromous ep's ESIT is larger than @XHCI_MTK_MAX_ESIT,
+ * round down to the limit value, that means allocating more
+ * bandwidth to it.
+ */
+#define XHCI_MTK_MAX_ESIT	64
+
+/**
+ * struct mu3h_sch_bw_info: schedule information for bandwidth domain
+ *
+ * @bus_bw: array to keep track of bandwidth already used at each uframes
+ * @bw_ep_list: eps in the bandwidth domain
+ *
+ * treat a HS root port as a bandwidth domain, but treat a SS root port as
+ * two bandwidth domains, one for IN eps and another for OUT eps.
+ */
+struct mu3h_sch_bw_info {
+	u32 bus_bw[XHCI_MTK_MAX_ESIT];
+	struct list_head bw_ep_list;
+};
+
+/**
+ * struct mu3h_sch_ep_info: schedule information for endpoint
+ *
+ * @esit: unit is 125us, equal to 2 << Interval field in ep-context
+ * @num_budget_microframes: number of continuous uframes
+ *		(@repeat==1) scheduled within the interval
+ * @bw_cost_per_microframe: bandwidth cost per microframe
+ * @endpoint: linked into bandwidth domain which it belongs to
+ * @ep: address of usb_host_endpoint struct
+ * @offset: which uframe of the interval that transfer should be
+ *		scheduled first time within the interval
+ * @repeat: the time gap between two uframes that transfers are
+ *		scheduled within a interval. in the simple algorithm, only
+ *		assign 0 or 1 to it; 0 means using only one uframe in a
+ *		interval, and 1 means using @num_budget_microframes
+ *		continuous uframes
+ * @pkts: number of packets to be transferred in the scheduled uframes
+ * @cs_count: number of CS that host will trigger
+ * @burst_mode: burst mode for scheduling. 0: normal burst mode,
+ *		distribute the bMaxBurst+1 packets for a single burst
+ *		according to @pkts and @repeat, repeate the burst multiple
+ *		times; 1: distribute the (bMaxBurst+1)*(Mult+1) packets
+ *		according to @pkts and @repeat. normal mode is used by
+ *		default
+ */
+struct mu3h_sch_ep_info {
+	u32 esit;
+	u32 num_budget_microframes;
+	u32 bw_cost_per_microframe;
+	struct list_head endpoint;
+	void *ep;
+	/*
+	 * mtk xHCI scheduling information put into reserved DWs
+	 * in ep context
+	 */
+	u32 offset;
+	u32 repeat;
+	u32 pkts;
+	u32 cs_count;
+	u32 burst_mode;
+};
+
+#define MU3C_U3_PORT_MAX 4
+#define MU3C_U2_PORT_MAX 5
+
+/**
+ * struct mu3c_ippc_regs: MTK ssusb ip port control registers
+ * @ip_pw_ctr0~3: ip power and clock control registers
+ * @ip_pw_sts1~2: ip power and clock status registers
+ * @ip_xhci_cap: ip xHCI capability register
+ * @u3_ctrl_p[x]: ip usb3 port x control register, only low 4bytes are used
+ * @u2_ctrl_p[x]: ip usb2 port x control register, only low 4bytes are used
+ * @u2_phy_pll: usb2 phy pll control register
+ */
+struct mu3c_ippc_regs {
+	__le32 ip_pw_ctr0;
+	__le32 ip_pw_ctr1;
+	__le32 ip_pw_ctr2;
+	__le32 ip_pw_ctr3;
+	__le32 ip_pw_sts1;
+	__le32 ip_pw_sts2;
+	__le32 reserved0[3];
+	__le32 ip_xhci_cap;
+	__le32 reserved1[2];
+	__le64 u3_ctrl_p[MU3C_U3_PORT_MAX];
+	__le64 u2_ctrl_p[MU3C_U2_PORT_MAX];
+	__le32 reserved2;
+	__le32 u2_phy_pll;
+	__le32 reserved3[33]; /* 0x80 ~ 0xff */
+};
+
+struct xhci_hcd_mtk {
+	struct device *dev;
+	struct usb_hcd *hcd;
+	struct mu3h_sch_bw_info *sch_array;
+	struct mu3c_ippc_regs __iomem *ippc_regs;
+	int num_u2_ports;
+	int num_u3_ports;
+	struct regulator *vusb33;
+	struct regulator *vbus;
+	struct clk *sys_clk;	/* sys and mac clock */
+	struct clk *wk_deb_p0;	/* port0's wakeup debounce clock */
+	struct clk *wk_deb_p1;
+	struct regmap *pericfg;
+	int wakeup_src;
+	struct phy **phys;
+	int num_phys;
+};
+
+#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
+int xhci_mtk_sch_init(struct xhci_hcd *xhci);
+void xhci_mtk_sch_exit(struct xhci_hcd *xhci);
+int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+
+#else
+static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
+	struct usb_device *udev, struct usb_host_endpoint *ep)
+{
+	return 0;
+}
+
+static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
+	struct usb_device *udev, struct usb_host_endpoint *ep)
+{
+}
+
+#endif
+
+#endif		/* _XHCI_MTK_H_ */
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 57f40a1..243f696 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -68,6 +68,7 @@
 #include <linux/slab.h>
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 /*
  * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
@@ -3044,18 +3045,27 @@ static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred,
 			      struct urb *urb, unsigned int num_trbs_left)
 {
 	u32 maxp, total_packet_count;
+	u32 skip_current_trb = 0;
 
-	if (xhci->hci_version < 0x100)
-		return ((td_total_len - transferred) >> 10);
-
-	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
-	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
+	if (xhci->hci_version < 0x100) {
+		/* for MTK xHCI, TD size doesn't include this TRB */
+		if (xhci->quirks & XHCI_MTK_HOST)
+			skip_current_trb = 1;
+		else
+			return ((td_total_len - transferred) >> 10);
+	}
 
 	/* One TRB with a zero-length data packet. */
 	if (num_trbs_left == 0 || (transferred == 0 && trb_buff_len == 0) ||
 	    trb_buff_len == td_total_len)
 		return 0;
 
+	if (skip_current_trb)
+		trb_buff_len = 0;
+
+	maxp = GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
+	total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
+
 	/* Queueing functions don't count the current TRB into transferred */
 	return (total_packet_count - ((transferred + trb_buff_len) / maxp));
 }
@@ -3443,7 +3453,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		field |= 0x1;
 
 	/* xHCI 1.0 6.4.1.2.1: Transfer Type field */
-	if (xhci->hci_version == 0x100) {
+	if ((xhci->hci_version == 0x100) || (xhci->quirks & XHCI_MTK_HOST)) {
 		if (urb->transfer_buffer_length > 0) {
 			if (setup->bRequestType & USB_DIR_IN)
 				field |= TRB_TX_TYPE(TRB_DATA_IN);
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 6b0f4a4..4741188 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -31,6 +31,7 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
+#include "xhci-mtk.h"
 
 #define DRIVER_AUTHOR "Sarah Sharp"
 #define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
@@ -623,7 +624,11 @@ int xhci_run(struct usb_hcd *hcd)
 			"// Set the interrupt modulation register");
 	temp = readl(&xhci->ir_set->irq_control);
 	temp &= ~ER_IRQ_INTERVAL_MASK;
-	temp |= (u32) 160;
+	/*
+	 * the increment interval is 8 times as much as that defined
+	 * in xHCI spec on MTK's controller
+	 */
+	temp |= (u32) ((xhci->quirks & XHCI_MTK_HOST) ? 20 : 160);
 	writel(temp, &xhci->ir_set->irq_control);
 
 	/* Set the HCD state before we enable the irqs */
@@ -1693,6 +1698,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
+	if (xhci->quirks & XHCI_MTK_HOST)
+		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
+
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1788,6 +1796,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
+	if (xhci->quirks & XHCI_MTK_HOST) {
+		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
+		if (ret < 0) {
+			xhci_free_or_cache_endpoint_ring(xhci,
+				virt_dev, ep_index);
+			return ret;
+		}
+	}
+
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index ea8b904..1536da0 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1577,6 +1577,7 @@ struct xhci_hcd {
 /* For controllers with a broken beyond repair streams implementation */
 #define XHCI_BROKEN_STREAMS	(1 << 19)
 #define XHCI_PME_STUCK_QUIRK	(1 << 20)
+#define XHCI_MTK_HOST		(1 << 21)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */
-- 
1.8.1.1.dirty

[PATCH v8 5/5] arm64: dts: mediatek: add xHCI & usb phy for mt8173

[Chunfeng Yun]

add xHCI and phy drivers for MT8173-EVB

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 16 +++++++++++
 arch/arm64/boot/dts/mediatek/mt8173.dtsi    | 43 +++++++++++++++++++++++++++++
 2 files changed, 59 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
index 4be66ca..d039a1c 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
@@ -13,6 +13,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "mt8173.dtsi"
 
 / {
@@ -32,6 +33,15 @@
 	};
 
 	chosen { };
+
+	usb_p1_vbus: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 130 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &i2c1 {
@@ -390,3 +400,9 @@
 &uart0 {
 	status = "okay";
 };
+
+&usb30 {
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	mediatek,wakeup-src = <1>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index d18ee42..ceca7a5 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -14,6 +14,7 @@
 #include <dt-bindings/clock/mt8173-clk.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/power/mt8173-power.h>
 #include <dt-bindings/reset-controller/mt8173-resets.h>
 #include "mt8173-pinfunc.h"
@@ -487,6 +488,48 @@
 			clock-names = "source", "hclk";
 			status = "disabled";
 		};
+
+		usb30: usb@11270000 {
+			compatible = "mediatek,mt8173-xhci";
+			reg = <0 0x11270000 0 0x1000>,
+			      <0 0x11280700 0 0x0100>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+			power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+			clocks = <&topckgen CLK_TOP_USB30_SEL>,
+				 <&pericfg CLK_PERI_USB0>,
+				 <&pericfg CLK_PERI_USB1>;
+			clock-names = "sys_ck",
+				      "wakeup_deb_p0",
+				      "wakeup_deb_p1";
+			phys = <&phy_port0 PHY_TYPE_USB3>,
+			       <&phy_port1 PHY_TYPE_USB2>;
+			usb3-lpm-capable;
+			mediatek,syscon-wakeup = <&pericfg>;
+			status = "okay";
+		};
+
+		u3phy: usb-phy@11290000 {
+			compatible = "mediatek,mt8173-u3phy";
+			reg = <0 0x11290000 0 0x800>;
+			clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+			clock-names = "u3phya_ref";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "okay";
+
+			phy_port0: port@11290800 {
+				reg = <0 0x11290800 0 0x800>;
+				#phy-cells = <1>;
+				status = "okay";
+			};
+
+			phy_port1: port@11291000 {
+				reg = <0 0x11291000 0 0x800>;
+				#phy-cells = <1>;
+				status = "okay";
+			};
+		};
 	};
 };
 
-- 
1.8.1.1.dirty

[PATCH v8 5/5] arm64: dts: mediatek: add xHCI & usb phy for mt8173

[Chunfeng Yun]

add xHCI and phy drivers for MT8173-EVB

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 16 +++++++++++
 arch/arm64/boot/dts/mediatek/mt8173.dtsi    | 43 +++++++++++++++++++++++++++++
 2 files changed, 59 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
index 4be66ca..d039a1c 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
@@ -13,6 +13,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "mt8173.dtsi"
 
 / {
@@ -32,6 +33,15 @@
 	};
 
 	chosen { };
+
+	usb_p1_vbus: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 130 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &i2c1 {
@@ -390,3 +400,9 @@
 &uart0 {
 	status = "okay";
 };
+
+&usb30 {
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	mediatek,wakeup-src = <1>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index d18ee42..ceca7a5 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -14,6 +14,7 @@
 #include <dt-bindings/clock/mt8173-clk.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/power/mt8173-power.h>
 #include <dt-bindings/reset-controller/mt8173-resets.h>
 #include "mt8173-pinfunc.h"
@@ -487,6 +488,48 @@
 			clock-names = "source", "hclk";
 			status = "disabled";
 		};
+
+		usb30: usb@11270000 {
+			compatible = "mediatek,mt8173-xhci";
+			reg = <0 0x11270000 0 0x1000>,
+			      <0 0x11280700 0 0x0100>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+			power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+			clocks = <&topckgen CLK_TOP_USB30_SEL>,
+				 <&pericfg CLK_PERI_USB0>,
+				 <&pericfg CLK_PERI_USB1>;
+			clock-names = "sys_ck",
+				      "wakeup_deb_p0",
+				      "wakeup_deb_p1";
+			phys = <&phy_port0 PHY_TYPE_USB3>,
+			       <&phy_port1 PHY_TYPE_USB2>;
+			usb3-lpm-capable;
+			mediatek,syscon-wakeup = <&pericfg>;
+			status = "okay";
+		};
+
+		u3phy: usb-phy@11290000 {
+			compatible = "mediatek,mt8173-u3phy";
+			reg = <0 0x11290000 0 0x800>;
+			clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+			clock-names = "u3phya_ref";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "okay";
+
+			phy_port0: port@11290800 {
+				reg = <0 0x11290800 0 0x800>;
+				#phy-cells = <1>;
+				status = "okay";
+			};
+
+			phy_port1: port@11291000 {
+				reg = <0 0x11291000 0 0x800>;
+				#phy-cells = <1>;
+				status = "okay";
+			};
+		};
 	};
 };
 
-- 
1.8.1.1.dirty

[PATCH v8 5/5] arm64: dts: mediatek: add xHCI & usb phy for mt8173

[Chunfeng Yun]

add xHCI and phy drivers for MT8173-EVB

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 16 +++++++++++
 arch/arm64/boot/dts/mediatek/mt8173.dtsi    | 43 +++++++++++++++++++++++++++++
 2 files changed, 59 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
index 4be66ca..d039a1c 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
@@ -13,6 +13,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "mt8173.dtsi"
 
 / {
@@ -32,6 +33,15 @@
 	};
 
 	chosen { };
+
+	usb_p1_vbus: regulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 130 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &i2c1 {
@@ -390,3 +400,9 @@
 &uart0 {
 	status = "okay";
 };
+
+&usb30 {
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p1_vbus>;
+	mediatek,wakeup-src = <1>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index d18ee42..ceca7a5 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -14,6 +14,7 @@
 #include <dt-bindings/clock/mt8173-clk.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/power/mt8173-power.h>
 #include <dt-bindings/reset-controller/mt8173-resets.h>
 #include "mt8173-pinfunc.h"
@@ -487,6 +488,48 @@
 			clock-names = "source", "hclk";
 			status = "disabled";
 		};
+
+		usb30: usb at 11270000 {
+			compatible = "mediatek,mt8173-xhci";
+			reg = <0 0x11270000 0 0x1000>,
+			      <0 0x11280700 0 0x0100>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+			power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+			clocks = <&topckgen CLK_TOP_USB30_SEL>,
+				 <&pericfg CLK_PERI_USB0>,
+				 <&pericfg CLK_PERI_USB1>;
+			clock-names = "sys_ck",
+				      "wakeup_deb_p0",
+				      "wakeup_deb_p1";
+			phys = <&phy_port0 PHY_TYPE_USB3>,
+			       <&phy_port1 PHY_TYPE_USB2>;
+			usb3-lpm-capable;
+			mediatek,syscon-wakeup = <&pericfg>;
+			status = "okay";
+		};
+
+		u3phy: usb-phy at 11290000 {
+			compatible = "mediatek,mt8173-u3phy";
+			reg = <0 0x11290000 0 0x800>;
+			clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+			clock-names = "u3phya_ref";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "okay";
+
+			phy_port0: port at 11290800 {
+				reg = <0 0x11290800 0 0x800>;
+				#phy-cells = <1>;
+				status = "okay";
+			};
+
+			phy_port1: port at 11291000 {
+				reg = <0 0x11291000 0 0x800>;
+				#phy-cells = <1>;
+				status = "okay";
+			};
+		};
 	};
 };
 
-- 
1.8.1.1.dirty

Re: [PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Kishon Vijay Abraham I]

Hi,

On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> support usb3.0 phy of mt65xx SoCs
few nitpicks:

change $subject. This driver is no longer in usb directory.

It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
>  drivers/phy/Kconfig           |   9 +
>  drivers/phy/Makefile          |   1 +
>  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 466 insertions(+)
>  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 47da573..ec436c1 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
>  	help
>  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
>  
> +config PHY_MT65XX_USB3
> +	tristate "Mediatek USB3.0 PHY Driver"
> +	depends on ARCH_MEDIATEK && OF
> +	select GENERIC_PHY
> +	help
> +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> +	  for mt65xx SoCs. it supports two usb2.0 ports and
> +	  one usb3.0 port.
> +
>  config PHY_SUN4I_USB
>  	tristate "Allwinner sunxi SoC USB PHY driver"
>  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a5b18c1..a7cc629 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
>  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
>  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
>  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
>  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
>  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
>  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> new file mode 100644
> index 0000000..1f00b05
> --- /dev/null
> +++ b/drivers/phy/phy-mt65xx-usb3.c
> @@ -0,0 +1,456 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +
> +/*
> + * for sifslv2 register, but exclude port's;
> + * relative to USB3_SIF2_BASE base address
> + */
> +#define SSUSB_SIFSLV_SPLLC		0x0000
> +
> +/* offsets of sub-segment in each port registers */
> +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> +
> +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> +
> +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> +
> +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> +
> +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> +#define PA6_RG_U2_ISO_EN		BIT(31)
> +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> +
> +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> +#define P2C_USB20_GPIO_MODE		BIT(8)
> +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> +
> +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> +
> +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> +#define P2C_FORCE_UART_EN		BIT(26)
> +#define P2C_FORCE_DATAIN		BIT(23)
> +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> +#define P2C_FORCE_XCVRSEL		BIT(19)
> +#define P2C_FORCE_SUSPENDM		BIT(18)
> +#define P2C_FORCE_TERMSEL		BIT(17)
> +#define P2C_RG_DATAIN			GENMASK(13, 10)
> +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> +#define P2C_RG_DMPULLDOWN		BIT(7)
> +#define P2C_RG_DPPULLDOWN		BIT(6)
> +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> +#define P2C_RG_SUSPENDM			BIT(3)
> +#define P2C_RG_TERMSEL			BIT(2)
> +#define P2C_DTM0_PART_MASK \
> +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> +
> +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> +#define P2C_RG_UART_EN			BIT(16)
> +#define P2C_RG_VBUSVALID		BIT(5)
> +#define P2C_RG_SESSEND			BIT(4)
> +#define P2C_RG_AVALID			BIT(2)
> +
> +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> +
> +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> +
> +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> +
> +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> +
> +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> +
> +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> +
> +struct mt65xx_phy_instance {
> +	struct phy *phy;
> +	void __iomem *port_base;
> +	u32 index;
> +	u8 type;
> +};
> +
> +struct mt65xx_u3phy {
> +	struct device *dev;
> +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> +	struct mt65xx_phy_instance **phys;
> +	int nphys;
> +};
> +
> +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	/* switch to USB function. (system register, force ip into usb mode) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~P2C_FORCE_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	tmp = readl(port_base + U3P_U2PHYDTM1);
> +	tmp &= ~P2C_RG_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM1);
> +
> +	if (!index) {
> +		tmp = readl(port_base + U3P_U2PHYACR4);
> +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> +		writel(tmp, port_base + U3P_U2PHYACR4);
> +	}
> +
> +	/* DP/DM BC1.1 path Disable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> +	tmp &= ~P3A_RG_RX_DAC_MUX;
> +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> +
> +	tmp = readl(port_base + U3P_PHYD_CDR1);
> +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> +	writel(tmp, port_base + U3P_PHYD_CDR1);
> +
> +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> +}
> +
> +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	if (!index) {
> +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> +		tmp |= P3A_RG_U3_VUSB10_ON;
> +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> +	}
> +
> +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	/* OTG Enable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	if (!index) {
> +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> +		/* [mt8173]disable Change 100uA current from SSUSB */
> +		tmp = readl(port_base + U3P_USBPHYACR5);
> +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> +		writel(tmp, port_base + U3P_USBPHYACR5);
> +	}
> +	udelay(800);

It's good to document delay values. Is it a recommended value from the
data manual?

Also now the registers doesn't seem to be shared between the PHYs. But
if it is then all these functions have to be protected with spinlock.

Thanks
Kishon

Re: [PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Kishon Vijay Abraham I]

Hi,

On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> support usb3.0 phy of mt65xx SoCs
few nitpicks:

change $subject. This driver is no longer in usb directory.

It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> ---
>  drivers/phy/Kconfig           |   9 +
>  drivers/phy/Makefile          |   1 +
>  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 466 insertions(+)
>  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 47da573..ec436c1 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
>  	help
>  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
>  
> +config PHY_MT65XX_USB3
> +	tristate "Mediatek USB3.0 PHY Driver"
> +	depends on ARCH_MEDIATEK && OF
> +	select GENERIC_PHY
> +	help
> +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> +	  for mt65xx SoCs. it supports two usb2.0 ports and
> +	  one usb3.0 port.
> +
>  config PHY_SUN4I_USB
>  	tristate "Allwinner sunxi SoC USB PHY driver"
>  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a5b18c1..a7cc629 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
>  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
>  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
>  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
>  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
>  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
>  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> new file mode 100644
> index 0000000..1f00b05
> --- /dev/null
> +++ b/drivers/phy/phy-mt65xx-usb3.c
> @@ -0,0 +1,456 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Chunfeng Yun <chunfeng.yun-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +
> +/*
> + * for sifslv2 register, but exclude port's;
> + * relative to USB3_SIF2_BASE base address
> + */
> +#define SSUSB_SIFSLV_SPLLC		0x0000
> +
> +/* offsets of sub-segment in each port registers */
> +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> +
> +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> +
> +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> +
> +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> +
> +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> +#define PA6_RG_U2_ISO_EN		BIT(31)
> +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> +
> +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> +#define P2C_USB20_GPIO_MODE		BIT(8)
> +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> +
> +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> +
> +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> +#define P2C_FORCE_UART_EN		BIT(26)
> +#define P2C_FORCE_DATAIN		BIT(23)
> +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> +#define P2C_FORCE_XCVRSEL		BIT(19)
> +#define P2C_FORCE_SUSPENDM		BIT(18)
> +#define P2C_FORCE_TERMSEL		BIT(17)
> +#define P2C_RG_DATAIN			GENMASK(13, 10)
> +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> +#define P2C_RG_DMPULLDOWN		BIT(7)
> +#define P2C_RG_DPPULLDOWN		BIT(6)
> +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> +#define P2C_RG_SUSPENDM			BIT(3)
> +#define P2C_RG_TERMSEL			BIT(2)
> +#define P2C_DTM0_PART_MASK \
> +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> +
> +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> +#define P2C_RG_UART_EN			BIT(16)
> +#define P2C_RG_VBUSVALID		BIT(5)
> +#define P2C_RG_SESSEND			BIT(4)
> +#define P2C_RG_AVALID			BIT(2)
> +
> +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> +
> +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> +
> +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> +
> +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> +
> +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> +
> +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> +
> +struct mt65xx_phy_instance {
> +	struct phy *phy;
> +	void __iomem *port_base;
> +	u32 index;
> +	u8 type;
> +};
> +
> +struct mt65xx_u3phy {
> +	struct device *dev;
> +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> +	struct mt65xx_phy_instance **phys;
> +	int nphys;
> +};
> +
> +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	/* switch to USB function. (system register, force ip into usb mode) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~P2C_FORCE_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	tmp = readl(port_base + U3P_U2PHYDTM1);
> +	tmp &= ~P2C_RG_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM1);
> +
> +	if (!index) {
> +		tmp = readl(port_base + U3P_U2PHYACR4);
> +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> +		writel(tmp, port_base + U3P_U2PHYACR4);
> +	}
> +
> +	/* DP/DM BC1.1 path Disable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> +	tmp &= ~P3A_RG_RX_DAC_MUX;
> +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> +
> +	tmp = readl(port_base + U3P_PHYD_CDR1);
> +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> +	writel(tmp, port_base + U3P_PHYD_CDR1);
> +
> +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> +}
> +
> +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	if (!index) {
> +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> +		tmp |= P3A_RG_U3_VUSB10_ON;
> +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> +	}
> +
> +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	/* OTG Enable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	if (!index) {
> +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> +		/* [mt8173]disable Change 100uA current from SSUSB */
> +		tmp = readl(port_base + U3P_USBPHYACR5);
> +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> +		writel(tmp, port_base + U3P_USBPHYACR5);
> +	}
> +	udelay(800);

It's good to document delay values. Is it a recommended value from the
data manual?

Also now the registers doesn't seem to be shared between the PHYs. But
if it is then all these functions have to be protected with spinlock.

Thanks
Kishon

[PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Kishon Vijay Abraham I]

Hi,

On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> support usb3.0 phy of mt65xx SoCs
few nitpicks:

change $subject. This driver is no longer in usb directory.

It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
>  drivers/phy/Kconfig           |   9 +
>  drivers/phy/Makefile          |   1 +
>  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 466 insertions(+)
>  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 47da573..ec436c1 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
>  	help
>  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
>  
> +config PHY_MT65XX_USB3
> +	tristate "Mediatek USB3.0 PHY Driver"
> +	depends on ARCH_MEDIATEK && OF
> +	select GENERIC_PHY
> +	help
> +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> +	  for mt65xx SoCs. it supports two usb2.0 ports and
> +	  one usb3.0 port.
> +
>  config PHY_SUN4I_USB
>  	tristate "Allwinner sunxi SoC USB PHY driver"
>  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a5b18c1..a7cc629 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
>  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
>  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
>  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
>  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
>  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
>  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> new file mode 100644
> index 0000000..1f00b05
> --- /dev/null
> +++ b/drivers/phy/phy-mt65xx-usb3.c
> @@ -0,0 +1,456 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +
> +/*
> + * for sifslv2 register, but exclude port's;
> + * relative to USB3_SIF2_BASE base address
> + */
> +#define SSUSB_SIFSLV_SPLLC		0x0000
> +
> +/* offsets of sub-segment in each port registers */
> +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> +
> +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> +
> +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> +
> +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> +
> +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> +#define PA6_RG_U2_ISO_EN		BIT(31)
> +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> +
> +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> +#define P2C_USB20_GPIO_MODE		BIT(8)
> +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> +
> +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> +
> +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> +#define P2C_FORCE_UART_EN		BIT(26)
> +#define P2C_FORCE_DATAIN		BIT(23)
> +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> +#define P2C_FORCE_XCVRSEL		BIT(19)
> +#define P2C_FORCE_SUSPENDM		BIT(18)
> +#define P2C_FORCE_TERMSEL		BIT(17)
> +#define P2C_RG_DATAIN			GENMASK(13, 10)
> +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> +#define P2C_RG_DMPULLDOWN		BIT(7)
> +#define P2C_RG_DPPULLDOWN		BIT(6)
> +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> +#define P2C_RG_SUSPENDM			BIT(3)
> +#define P2C_RG_TERMSEL			BIT(2)
> +#define P2C_DTM0_PART_MASK \
> +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> +
> +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> +#define P2C_RG_UART_EN			BIT(16)
> +#define P2C_RG_VBUSVALID		BIT(5)
> +#define P2C_RG_SESSEND			BIT(4)
> +#define P2C_RG_AVALID			BIT(2)
> +
> +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> +
> +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> +
> +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> +
> +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> +
> +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> +
> +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> +
> +struct mt65xx_phy_instance {
> +	struct phy *phy;
> +	void __iomem *port_base;
> +	u32 index;
> +	u8 type;
> +};
> +
> +struct mt65xx_u3phy {
> +	struct device *dev;
> +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> +	struct mt65xx_phy_instance **phys;
> +	int nphys;
> +};
> +
> +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	/* switch to USB function. (system register, force ip into usb mode) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~P2C_FORCE_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	tmp = readl(port_base + U3P_U2PHYDTM1);
> +	tmp &= ~P2C_RG_UART_EN;
> +	writel(tmp, port_base + U3P_U2PHYDTM1);
> +
> +	if (!index) {
> +		tmp = readl(port_base + U3P_U2PHYACR4);
> +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> +		writel(tmp, port_base + U3P_U2PHYACR4);
> +	}
> +
> +	/* DP/DM BC1.1 path Disable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> +	tmp &= ~P3A_RG_RX_DAC_MUX;
> +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> +
> +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> +
> +	tmp = readl(port_base + U3P_PHYD_CDR1);
> +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> +	writel(tmp, port_base + U3P_PHYD_CDR1);
> +
> +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> +}
> +
> +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> +	struct mt65xx_phy_instance *instance)
> +{
> +	void __iomem *port_base = instance->port_base;
> +	u32 index = instance->index;
> +	u32 tmp;
> +
> +	if (!index) {
> +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> +		tmp |= P3A_RG_U3_VUSB10_ON;
> +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> +	}
> +
> +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> +	tmp = readl(port_base + U3P_U2PHYDTM0);
> +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> +	writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> +	/* OTG Enable */
> +	tmp = readl(port_base + U3P_USBPHYACR6);
> +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> +	writel(tmp, port_base + U3P_USBPHYACR6);
> +
> +	if (!index) {
> +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> +		/* [mt8173]disable Change 100uA current from SSUSB */
> +		tmp = readl(port_base + U3P_USBPHYACR5);
> +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> +		writel(tmp, port_base + U3P_USBPHYACR5);
> +	}
> +	udelay(800);

It's good to document delay values. Is it a recommended value from the
data manual?

Also now the registers doesn't seem to be shared between the PHYs. But
if it is then all these functions have to be protected with spinlock.

Thanks
Kishon

Re: [PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[chunfeng yun]

hi,
On Fri, 2015-09-18 at 12:12 +0530, Kishon Vijay Abraham I wrote:
> Hi,
> 
> On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> > support usb3.0 phy of mt65xx SoCs
> few nitpicks:
> 
> change $subject. This driver is no longer in usb directory.
> 
> It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
Ok

> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> >  drivers/phy/Kconfig           |   9 +
> >  drivers/phy/Makefile          |   1 +
> >  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 466 insertions(+)
> >  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> > 
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> > index 47da573..ec436c1 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
> >  	help
> >  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
> >  
> > +config PHY_MT65XX_USB3
> > +	tristate "Mediatek USB3.0 PHY Driver"
> > +	depends on ARCH_MEDIATEK && OF
> > +	select GENERIC_PHY
> > +	help
> > +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> > +	  for mt65xx SoCs. it supports two usb2.0 ports and
> > +	  one usb3.0 port.
> > +
> >  config PHY_SUN4I_USB
> >  	tristate "Allwinner sunxi SoC USB PHY driver"
> >  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> > index a5b18c1..a7cc629 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
> >  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
> >  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
> >  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> > +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
> >  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
> >  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
> >  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> > diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> > new file mode 100644
> > index 0000000..1f00b05
> > --- /dev/null
> > +++ b/drivers/phy/phy-mt65xx-usb3.c
> > @@ -0,0 +1,456 @@
> > +/*
> > + * Copyright (c) 2015 MediaTek Inc.
> > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + * GNU General Public License for more details.
> > + *
> > + */
> > +
> > +#include <dt-bindings/phy/phy.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +
> > +/*
> > + * for sifslv2 register, but exclude port's;
> > + * relative to USB3_SIF2_BASE base address
> > + */
> > +#define SSUSB_SIFSLV_SPLLC		0x0000
> > +
> > +/* offsets of sub-segment in each port registers */
> > +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> > +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> > +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> > +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> > +
> > +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> > +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > +
> > +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> > +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> > +
> > +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> > +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> > +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> > +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> > +
> > +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> > +#define PA6_RG_U2_ISO_EN		BIT(31)
> > +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> > +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> > +
> > +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> > +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> > +#define P2C_USB20_GPIO_MODE		BIT(8)
> > +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > +
> > +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> > +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> > +
> > +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> > +#define P2C_FORCE_UART_EN		BIT(26)
> > +#define P2C_FORCE_DATAIN		BIT(23)
> > +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> > +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> > +#define P2C_FORCE_XCVRSEL		BIT(19)
> > +#define P2C_FORCE_SUSPENDM		BIT(18)
> > +#define P2C_FORCE_TERMSEL		BIT(17)
> > +#define P2C_RG_DATAIN			GENMASK(13, 10)
> > +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> > +#define P2C_RG_DMPULLDOWN		BIT(7)
> > +#define P2C_RG_DPPULLDOWN		BIT(6)
> > +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> > +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> > +#define P2C_RG_SUSPENDM			BIT(3)
> > +#define P2C_RG_TERMSEL			BIT(2)
> > +#define P2C_DTM0_PART_MASK \
> > +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> > +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> > +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> > +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> > +
> > +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> > +#define P2C_RG_UART_EN			BIT(16)
> > +#define P2C_RG_VBUSVALID		BIT(5)
> > +#define P2C_RG_SESSEND			BIT(4)
> > +#define P2C_RG_AVALID			BIT(2)
> > +
> > +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> > +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> > +
> > +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> > +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> > +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> > +
> > +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> > +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> > +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> > +
> > +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> > +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> > +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> > +
> > +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> > +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> > +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> > +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> > +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> > +
> > +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> > +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> > +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> > +
> > +struct mt65xx_phy_instance {
> > +	struct phy *phy;
> > +	void __iomem *port_base;
> > +	u32 index;
> > +	u8 type;
> > +};
> > +
> > +struct mt65xx_u3phy {
> > +	struct device *dev;
> > +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> > +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> > +	struct mt65xx_phy_instance **phys;
> > +	int nphys;
> > +};
> > +
> > +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	/* switch to USB function. (system register, force ip into usb mode) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~P2C_FORCE_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	tmp = readl(port_base + U3P_U2PHYDTM1);
> > +	tmp &= ~P2C_RG_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM1);
> > +
> > +	if (!index) {
> > +		tmp = readl(port_base + U3P_U2PHYACR4);
> > +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> > +		writel(tmp, port_base + U3P_U2PHYACR4);
> > +	}
> > +
> > +	/* DP/DM BC1.1 path Disable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> > +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> > +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> > +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> > +	tmp &= ~P3A_RG_RX_DAC_MUX;
> > +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> > +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> > +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> > +
> > +	tmp = readl(port_base + U3P_PHYD_CDR1);
> > +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> > +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> > +	writel(tmp, port_base + U3P_PHYD_CDR1);
> > +
> > +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> > +}
> > +
> > +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	if (!index) {
> > +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> > +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> > +		tmp |= P3A_RG_U3_VUSB10_ON;
> > +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> > +	}
> > +
> > +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> > +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	/* OTG Enable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	if (!index) {
> > +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> > +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> > +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> > +		/* [mt8173]disable Change 100uA current from SSUSB */
> > +		tmp = readl(port_base + U3P_USBPHYACR5);
> > +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> > +		writel(tmp, port_base + U3P_USBPHYACR5);
> > +	}
> > +	udelay(800);
> 
> It's good to document delay values. Is it a recommended value from the
> data manual?
> 
I check it with DE, and revise it after many tests.

> Also now the registers doesn't seem to be shared between the PHYs. But
> if it is then all these functions have to be protected with spinlock.
> 
I will pay attention to it.

Thanks a lot

> Thanks
> Kishon

Re: [PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[chunfeng yun]

hi,
On Fri, 2015-09-18 at 12:12 +0530, Kishon Vijay Abraham I wrote:
> Hi,
> 
> On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> > support usb3.0 phy of mt65xx SoCs
> few nitpicks:
> 
> change $subject. This driver is no longer in usb directory.
> 
> It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
Ok

> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> >  drivers/phy/Kconfig           |   9 +
> >  drivers/phy/Makefile          |   1 +
> >  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 466 insertions(+)
> >  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> > 
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> > index 47da573..ec436c1 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
> >  	help
> >  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
> >  
> > +config PHY_MT65XX_USB3
> > +	tristate "Mediatek USB3.0 PHY Driver"
> > +	depends on ARCH_MEDIATEK && OF
> > +	select GENERIC_PHY
> > +	help
> > +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> > +	  for mt65xx SoCs. it supports two usb2.0 ports and
> > +	  one usb3.0 port.
> > +
> >  config PHY_SUN4I_USB
> >  	tristate "Allwinner sunxi SoC USB PHY driver"
> >  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> > index a5b18c1..a7cc629 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
> >  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
> >  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
> >  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> > +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
> >  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
> >  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
> >  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> > diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> > new file mode 100644
> > index 0000000..1f00b05
> > --- /dev/null
> > +++ b/drivers/phy/phy-mt65xx-usb3.c
> > @@ -0,0 +1,456 @@
> > +/*
> > + * Copyright (c) 2015 MediaTek Inc.
> > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + * GNU General Public License for more details.
> > + *
> > + */
> > +
> > +#include <dt-bindings/phy/phy.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +
> > +/*
> > + * for sifslv2 register, but exclude port's;
> > + * relative to USB3_SIF2_BASE base address
> > + */
> > +#define SSUSB_SIFSLV_SPLLC		0x0000
> > +
> > +/* offsets of sub-segment in each port registers */
> > +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> > +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> > +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> > +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> > +
> > +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> > +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > +
> > +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> > +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> > +
> > +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> > +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> > +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> > +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> > +
> > +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> > +#define PA6_RG_U2_ISO_EN		BIT(31)
> > +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> > +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> > +
> > +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> > +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> > +#define P2C_USB20_GPIO_MODE		BIT(8)
> > +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > +
> > +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> > +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> > +
> > +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> > +#define P2C_FORCE_UART_EN		BIT(26)
> > +#define P2C_FORCE_DATAIN		BIT(23)
> > +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> > +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> > +#define P2C_FORCE_XCVRSEL		BIT(19)
> > +#define P2C_FORCE_SUSPENDM		BIT(18)
> > +#define P2C_FORCE_TERMSEL		BIT(17)
> > +#define P2C_RG_DATAIN			GENMASK(13, 10)
> > +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> > +#define P2C_RG_DMPULLDOWN		BIT(7)
> > +#define P2C_RG_DPPULLDOWN		BIT(6)
> > +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> > +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> > +#define P2C_RG_SUSPENDM			BIT(3)
> > +#define P2C_RG_TERMSEL			BIT(2)
> > +#define P2C_DTM0_PART_MASK \
> > +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> > +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> > +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> > +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> > +
> > +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> > +#define P2C_RG_UART_EN			BIT(16)
> > +#define P2C_RG_VBUSVALID		BIT(5)
> > +#define P2C_RG_SESSEND			BIT(4)
> > +#define P2C_RG_AVALID			BIT(2)
> > +
> > +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> > +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> > +
> > +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> > +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> > +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> > +
> > +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> > +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> > +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> > +
> > +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> > +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> > +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> > +
> > +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> > +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> > +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> > +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> > +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> > +
> > +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> > +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> > +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> > +
> > +struct mt65xx_phy_instance {
> > +	struct phy *phy;
> > +	void __iomem *port_base;
> > +	u32 index;
> > +	u8 type;
> > +};
> > +
> > +struct mt65xx_u3phy {
> > +	struct device *dev;
> > +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> > +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> > +	struct mt65xx_phy_instance **phys;
> > +	int nphys;
> > +};
> > +
> > +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	/* switch to USB function. (system register, force ip into usb mode) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~P2C_FORCE_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	tmp = readl(port_base + U3P_U2PHYDTM1);
> > +	tmp &= ~P2C_RG_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM1);
> > +
> > +	if (!index) {
> > +		tmp = readl(port_base + U3P_U2PHYACR4);
> > +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> > +		writel(tmp, port_base + U3P_U2PHYACR4);
> > +	}
> > +
> > +	/* DP/DM BC1.1 path Disable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> > +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> > +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> > +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> > +	tmp &= ~P3A_RG_RX_DAC_MUX;
> > +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> > +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> > +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> > +
> > +	tmp = readl(port_base + U3P_PHYD_CDR1);
> > +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> > +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> > +	writel(tmp, port_base + U3P_PHYD_CDR1);
> > +
> > +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> > +}
> > +
> > +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	if (!index) {
> > +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> > +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> > +		tmp |= P3A_RG_U3_VUSB10_ON;
> > +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> > +	}
> > +
> > +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> > +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	/* OTG Enable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	if (!index) {
> > +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> > +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> > +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> > +		/* [mt8173]disable Change 100uA current from SSUSB */
> > +		tmp = readl(port_base + U3P_USBPHYACR5);
> > +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> > +		writel(tmp, port_base + U3P_USBPHYACR5);
> > +	}
> > +	udelay(800);
> 
> It's good to document delay values. Is it a recommended value from the
> data manual?
> 
I check it with DE, and revise it after many tests.

> Also now the registers doesn't seem to be shared between the PHYs. But
> if it is then all these functions have to be protected with spinlock.
> 
I will pay attention to it.

Thanks a lot

> Thanks
> Kishon

[PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[chunfeng yun]

hi,
On Fri, 2015-09-18 at 12:12 +0530, Kishon Vijay Abraham I wrote:
> Hi,
> 
> On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> > support usb3.0 phy of mt65xx SoCs
> few nitpicks:
> 
> change $subject. This driver is no longer in usb directory.
> 
> It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
Ok

> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> >  drivers/phy/Kconfig           |   9 +
> >  drivers/phy/Makefile          |   1 +
> >  drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 466 insertions(+)
> >  create mode 100644 drivers/phy/phy-mt65xx-usb3.c
> > 
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> > index 47da573..ec436c1 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
> >  	help
> >  	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
> >  
> > +config PHY_MT65XX_USB3
> > +	tristate "Mediatek USB3.0 PHY Driver"
> > +	depends on ARCH_MEDIATEK && OF
> > +	select GENERIC_PHY
> > +	help
> > +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> > +	  for mt65xx SoCs. it supports two usb2.0 ports and
> > +	  one usb3.0 port.
> > +
> >  config PHY_SUN4I_USB
> >  	tristate "Allwinner sunxi SoC USB PHY driver"
> >  	depends on ARCH_SUNXI && HAS_IOMEM && OF
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> > index a5b18c1..a7cc629 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
> >  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
> >  obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
> >  obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
> > +obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
> >  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
> >  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
> >  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> > diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> > new file mode 100644
> > index 0000000..1f00b05
> > --- /dev/null
> > +++ b/drivers/phy/phy-mt65xx-usb3.c
> > @@ -0,0 +1,456 @@
> > +/*
> > + * Copyright (c) 2015 MediaTek Inc.
> > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + * GNU General Public License for more details.
> > + *
> > + */
> > +
> > +#include <dt-bindings/phy/phy.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +
> > +/*
> > + * for sifslv2 register, but exclude port's;
> > + * relative to USB3_SIF2_BASE base address
> > + */
> > +#define SSUSB_SIFSLV_SPLLC		0x0000
> > +
> > +/* offsets of sub-segment in each port registers */
> > +#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
> > +#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
> > +#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
> > +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
> > +
> > +#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> > +#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> > +
> > +#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> > +#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
> > +
> > +#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> > +#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
> > +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> > +#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
> > +
> > +#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> > +#define PA6_RG_U2_ISO_EN		BIT(31)
> > +#define PA6_RG_U2_BC11_SW_EN		BIT(23)
> > +#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
> > +
> > +#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> > +#define P2C_RG_USB20_GPIO_CTL		BIT(9)
> > +#define P2C_USB20_GPIO_MODE		BIT(8)
> > +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > +
> > +#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> > +#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
> > +
> > +#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> > +#define P2C_FORCE_UART_EN		BIT(26)
> > +#define P2C_FORCE_DATAIN		BIT(23)
> > +#define P2C_FORCE_DM_PULLDOWN		BIT(21)
> > +#define P2C_FORCE_DP_PULLDOWN		BIT(20)
> > +#define P2C_FORCE_XCVRSEL		BIT(19)
> > +#define P2C_FORCE_SUSPENDM		BIT(18)
> > +#define P2C_FORCE_TERMSEL		BIT(17)
> > +#define P2C_RG_DATAIN			GENMASK(13, 10)
> > +#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
> > +#define P2C_RG_DMPULLDOWN		BIT(7)
> > +#define P2C_RG_DPPULLDOWN		BIT(6)
> > +#define P2C_RG_XCVRSEL			GENMASK(5, 4)
> > +#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
> > +#define P2C_RG_SUSPENDM			BIT(3)
> > +#define P2C_RG_TERMSEL			BIT(2)
> > +#define P2C_DTM0_PART_MASK \
> > +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> > +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> > +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> > +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> > +
> > +#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> > +#define P2C_RG_UART_EN			BIT(16)
> > +#define P2C_RG_VBUSVALID		BIT(5)
> > +#define P2C_RG_SESSEND			BIT(4)
> > +#define P2C_RG_AVALID			BIT(2)
> > +
> > +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> > +#define P3A_RG_U3_VUSB10_ON		BIT(5)
> > +
> > +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> > +#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
> > +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> > +
> > +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> > +#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
> > +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> > +
> > +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> > +#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
> > +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> > +
> > +#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> > +#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> > +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> > +#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
> > +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> > +
> > +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
> > +#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
> > +#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> > +
> > +struct mt65xx_phy_instance {
> > +	struct phy *phy;
> > +	void __iomem *port_base;
> > +	u32 index;
> > +	u8 type;
> > +};
> > +
> > +struct mt65xx_u3phy {
> > +	struct device *dev;
> > +	void __iomem *sif_base;	/* include sif2, but exclude port's */
> > +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> > +	struct mt65xx_phy_instance **phys;
> > +	int nphys;
> > +};
> > +
> > +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	/* switch to USB function. (system register, force ip into usb mode) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~P2C_FORCE_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	tmp = readl(port_base + U3P_U2PHYDTM1);
> > +	tmp &= ~P2C_RG_UART_EN;
> > +	writel(tmp, port_base + U3P_U2PHYDTM1);
> > +
> > +	if (!index) {
> > +		tmp = readl(port_base + U3P_U2PHYACR4);
> > +		tmp &= ~P2C_U2_GPIO_CTR_MSK;
> > +		writel(tmp, port_base + U3P_U2PHYACR4);
> > +	}
> > +
> > +	/* DP/DM BC1.1 path Disable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp &= ~PA6_RG_U2_BC11_SW_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> > +	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> > +	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> > +	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG9);
> > +	tmp &= ~P3A_RG_RX_DAC_MUX;
> > +	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG9);
> > +
> > +	tmp = readl(port_base + U3P_U3_PHYA_REG6);
> > +	tmp &= ~P3A_RG_TX_EIDLE_CM;
> > +	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> > +	writel(tmp, port_base + U3P_U3_PHYA_REG6);
> > +
> > +	tmp = readl(port_base + U3P_PHYD_CDR1);
> > +	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> > +	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> > +	writel(tmp, port_base + U3P_PHYD_CDR1);
> > +
> > +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> > +}
> > +
> > +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> > +	struct mt65xx_phy_instance *instance)
> > +{
> > +	void __iomem *port_base = instance->port_base;
> > +	u32 index = instance->index;
> > +	u32 tmp;
> > +
> > +	if (!index) {
> > +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> > +		tmp = readl(port_base + U3P_U3_PHYA_REG0);
> > +		tmp |= P3A_RG_U3_VUSB10_ON;
> > +		writel(tmp, port_base + U3P_U3_PHYA_REG0);
> > +	}
> > +
> > +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> > +	tmp = readl(port_base + U3P_U2PHYDTM0);
> > +	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> > +	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> > +	writel(tmp, port_base + U3P_U2PHYDTM0);
> > +
> > +	/* OTG Enable */
> > +	tmp = readl(port_base + U3P_USBPHYACR6);
> > +	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> > +	writel(tmp, port_base + U3P_USBPHYACR6);
> > +
> > +	if (!index) {
> > +		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> > +		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> > +		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> > +		/* [mt8173]disable Change 100uA current from SSUSB */
> > +		tmp = readl(port_base + U3P_USBPHYACR5);
> > +		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> > +		writel(tmp, port_base + U3P_USBPHYACR5);
> > +	}
> > +	udelay(800);
> 
> It's good to document delay values. Is it a recommended value from the
> data manual?
> 
I check it with DE, and revise it after many tests.

> Also now the registers doesn't seem to be shared between the PHYs. But
> if it is then all these functions have to be protected with spinlock.
> 
I will pay attention to it.

Thanks a lot

> Thanks
> Kishon