* [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
@ 2015-10-22 16:20 ` Andrew F. Davis
0 siblings, 0 replies; 9+ messages in thread
From: Andrew F. Davis @ 2015-10-22 16:20 UTC (permalink / raw)
To: Benoît Cousson, Tony Lindgren
Cc: devicetree, linux-omap, linux-kernel, Andrew F. Davis
Using constants for pinctrl allows better readability and removes
redundancy with comments.
Signed-off-by: Andrew F. Davis <afd@ti.com>
---
arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++-----------------
1 file changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index eadbba3..a540a10 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -36,32 +36,32 @@
&am33xx_pinmux {
nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
pinctrl-single,pins = <
- 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
- 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
- 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
- 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
- 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
>;
};
nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
pinctrl-single,pins = <
- 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+ 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
>;
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
@ 2015-10-22 16:20 ` Andrew F. Davis
0 siblings, 0 replies; 9+ messages in thread
From: Andrew F. Davis @ 2015-10-22 16:20 UTC (permalink / raw)
To: Benoît Cousson, Tony Lindgren
Cc: devicetree, linux-omap, linux-kernel, Andrew F. Davis
Using constants for pinctrl allows better readability and removes
redundancy with comments.
Signed-off-by: Andrew F. Davis <afd@ti.com>
---
arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++-----------------
1 file changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index eadbba3..a540a10 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -36,32 +36,32 @@
&am33xx_pinmux {
nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
pinctrl-single,pins = <
- 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
- 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
- 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
- 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
- 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
- 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
>;
};
nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
pinctrl-single,pins = <
- 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+ 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
>;
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
@ 2015-10-22 21:23 ` Tony Lindgren
0 siblings, 0 replies; 9+ messages in thread
From: Tony Lindgren @ 2015-10-22 21:23 UTC (permalink / raw)
To: Andrew F. Davis; +Cc: Benoît Cousson, devicetree, linux-omap, linux-kernel
* Andrew F. Davis <afd@ti.com> [151022 09:21]:
> Using constants for pinctrl allows better readability and removes
> redundancy with comments.
You should use the include/dt-bindings/pinctrl/omap.h macro
AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
the same things again later on.
Regards,
Tony
> Signed-off-by: Andrew F. Davis <afd@ti.com>
> ---
> arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++-----------------
> 1 file changed, 22 insertions(+), 22 deletions(-)
>
> diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
> index eadbba3..a540a10 100644
> --- a/arch/arm/boot/dts/am335x-boneblack.dts
> +++ b/arch/arm/boot/dts/am335x-boneblack.dts
> @@ -36,32 +36,32 @@
> &am33xx_pinmux {
> nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
> pinctrl-single,pins = <
> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
> - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
> + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
> + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
> + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
> + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
> + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
> + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
> + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
> + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
> + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
> + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
> + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
> + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
> + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
> + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
> + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
> + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
> + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
> + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
> + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
> + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
> >;
> };
> nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
> pinctrl-single,pins = <
> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
> >;
> };
> };
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
@ 2015-10-22 21:23 ` Tony Lindgren
0 siblings, 0 replies; 9+ messages in thread
From: Tony Lindgren @ 2015-10-22 21:23 UTC (permalink / raw)
To: Andrew F. Davis
Cc: Benoît Cousson, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
* Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org> [151022 09:21]:
> Using constants for pinctrl allows better readability and removes
> redundancy with comments.
You should use the include/dt-bindings/pinctrl/omap.h macro
AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
the same things again later on.
Regards,
Tony
> Signed-off-by: Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org>
> ---
> arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++-----------------
> 1 file changed, 22 insertions(+), 22 deletions(-)
>
> diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
> index eadbba3..a540a10 100644
> --- a/arch/arm/boot/dts/am335x-boneblack.dts
> +++ b/arch/arm/boot/dts/am335x-boneblack.dts
> @@ -36,32 +36,32 @@
> &am33xx_pinmux {
> nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
> pinctrl-single,pins = <
> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
> - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
> - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
> + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
> + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
> + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
> + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
> + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
> + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
> + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
> + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
> + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
> + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
> + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
> + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
> + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
> + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
> + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
> + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
> + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
> + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
> + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
> + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
> >;
> };
> nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
> pinctrl-single,pins = <
> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
> >;
> };
> };
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
2015-10-22 21:23 ` Tony Lindgren
(?)
@ 2015-10-23 13:08 ` Andrew F. Davis
2015-10-23 14:29 ` Javier Martinez Canillas
-1 siblings, 1 reply; 9+ messages in thread
From: Andrew F. Davis @ 2015-10-23 13:08 UTC (permalink / raw)
To: Tony Lindgren; +Cc: Benoît Cousson, devicetree, linux-omap, linux-kernel
On 10/22/2015 04:23 PM, Tony Lindgren wrote:
> * Andrew F. Davis <afd@ti.com> [151022 09:21]:
>> Using constants for pinctrl allows better readability and removes
>> redundancy with comments.
>
> You should use the include/dt-bindings/pinctrl/omap.h macro
> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
> the same things again later on.
>
Hmm, I haven't really been following this change, it kind of seems to add
some unnecessary abstraction by using physical hardware addresses instead
of offsets, then just converting them back to offsets. The offset style DT
nodes are already auto-generated with existing tools anyway:
https://dev.ti.com/pinmux
I'm sure this has been discussed already so if this is a blocker I'll
re-spin this.
Andrew
> Regards,
>
> Tony
>
>> Signed-off-by: Andrew F. Davis <afd@ti.com>
>> ---
>> arch/arm/boot/dts/am335x-boneblack.dts | 44 +++++++++++++++++-----------------
>> 1 file changed, 22 insertions(+), 22 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
>> index eadbba3..a540a10 100644
>> --- a/arch/arm/boot/dts/am335x-boneblack.dts
>> +++ b/arch/arm/boot/dts/am335x-boneblack.dts
>> @@ -36,32 +36,32 @@
>> &am33xx_pinmux {
>> nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
>> pinctrl-single,pins = <
>> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
>> - 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
>> - 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
>> - 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
>> - 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
>> - 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
>> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
>> + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
>> + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
>> + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
>> + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
>> + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
>> + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
>> + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
>> + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
>> + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
>> + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
>> + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
>> + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
>> + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
>> + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
>> + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
>> + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
>> + 0xe0 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
>> + 0xe4 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
>> + 0xe8 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
>> + 0xec (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
>> >;
>> };
>> nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
>> pinctrl-single,pins = <
>> - 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
>> + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
>> >;
>> };
>> };
>> --
>> 1.9.1
>>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
2015-10-23 13:08 ` Andrew F. Davis
@ 2015-10-23 14:29 ` Javier Martinez Canillas
2015-10-23 14:36 ` Andrew F. Davis
0 siblings, 1 reply; 9+ messages in thread
From: Javier Martinez Canillas @ 2015-10-23 14:29 UTC (permalink / raw)
To: Andrew F. Davis
Cc: Tony Lindgren, Benoît Cousson, devicetree, linux-omap, Linux Kernel
Hello Andrew,
On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd@ti.com> wrote:
> On 10/22/2015 04:23 PM, Tony Lindgren wrote:
>>
>> * Andrew F. Davis <afd@ti.com> [151022 09:21]:
>>>
>>> Using constants for pinctrl allows better readability and removes
>>> redundancy with comments.
>>
>>
>> You should use the include/dt-bindings/pinctrl/omap.h macro
>> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
>> the same things again later on.
>>
>
> Hmm, I haven't really been following this change, it kind of seems to add
> some unnecessary abstraction by using physical hardware addresses instead
> of offsets, then just converting them back to offsets. The offset style DT
> nodes are already auto-generated with existing tools anyway:
> https://dev.ti.com/pinmux
>
> I'm sure this has been discussed already so if this is a blocker I'll
> re-spin this.
>
The good thing about the IOPAD pinmux macros is that matches what is
in the TRM so it is easier to read the DTS and verify that is correct.
I've on my queue to migrate all the remaining DTS for TI SoCs to use
the IOPAD macros but is just that I didn't have time to do it this
week. Probably I'll do it at the end of the next week.
> Andrew
>
>
>> Regards,
>>
Best regards,
Javier
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
2015-10-23 14:29 ` Javier Martinez Canillas
@ 2015-10-23 14:36 ` Andrew F. Davis
2015-10-23 14:47 ` Javier Martinez Canillas
0 siblings, 1 reply; 9+ messages in thread
From: Andrew F. Davis @ 2015-10-23 14:36 UTC (permalink / raw)
To: Javier Martinez Canillas
Cc: Tony Lindgren, Benoît Cousson, devicetree, linux-omap, Linux Kernel
On 10/23/2015 09:29 AM, Javier Martinez Canillas wrote:
> Hello Andrew,
>
> On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd@ti.com> wrote:
>> On 10/22/2015 04:23 PM, Tony Lindgren wrote:
>>>
>>> * Andrew F. Davis <afd@ti.com> [151022 09:21]:
>>>>
>>>> Using constants for pinctrl allows better readability and removes
>>>> redundancy with comments.
>>>
>>>
>>> You should use the include/dt-bindings/pinctrl/omap.h macro
>>> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
>>> the same things again later on.
>>>
>>
>> Hmm, I haven't really been following this change, it kind of seems to add
>> some unnecessary abstraction by using physical hardware addresses instead
>> of offsets, then just converting them back to offsets. The offset style DT
>> nodes are already auto-generated with existing tools anyway:
>> https://dev.ti.com/pinmux
>>
>> I'm sure this has been discussed already so if this is a blocker I'll
>> re-spin this.
>>
>
> The good thing about the IOPAD pinmux macros is that matches what is
> in the TRM so it is easier to read the DTS and verify that is correct.
>
> I've on my queue to migrate all the remaining DTS for TI SoCs to use
> the IOPAD macros but is just that I didn't have time to do it this
> week. Probably I'll do it at the end of the next week.
>
Then this patch can probably be dropped, hopefully the converted constants
in this patch can be of some help for you though.
Andrew
>> Andrew
>>
>>
>>> Regards,
>>>
>
> Best regards,
> Javier
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
@ 2015-10-23 14:47 ` Javier Martinez Canillas
0 siblings, 0 replies; 9+ messages in thread
From: Javier Martinez Canillas @ 2015-10-23 14:47 UTC (permalink / raw)
To: Andrew F. Davis
Cc: Tony Lindgren, Benoît Cousson, devicetree, linux-omap, Linux Kernel
Hello Andrew,
On Fri, Oct 23, 2015 at 4:36 PM, Andrew F. Davis <afd@ti.com> wrote:
> On 10/23/2015 09:29 AM, Javier Martinez Canillas wrote:
>>
>> Hello Andrew,
>>
>> On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd@ti.com> wrote:
>>>
>>> On 10/22/2015 04:23 PM, Tony Lindgren wrote:
>>>>
>>>>
>>>> * Andrew F. Davis <afd@ti.com> [151022 09:21]:
>>>>>
>>>>>
>>>>> Using constants for pinctrl allows better readability and removes
>>>>> redundancy with comments.
>>>>
>>>>
>>>>
>>>> You should use the include/dt-bindings/pinctrl/omap.h macro
>>>> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
>>>> the same things again later on.
>>>>
>>>
>>> Hmm, I haven't really been following this change, it kind of seems to add
>>> some unnecessary abstraction by using physical hardware addresses instead
>>> of offsets, then just converting them back to offsets. The offset style
>>> DT
>>> nodes are already auto-generated with existing tools anyway:
>>> https://dev.ti.com/pinmux
>>>
>>> I'm sure this has been discussed already so if this is a blocker I'll
>>> re-spin this.
>>>
>>
>> The good thing about the IOPAD pinmux macros is that matches what is
>> in the TRM so it is easier to read the DTS and verify that is correct.
>>
>> I've on my queue to migrate all the remaining DTS for TI SoCs to use
>> the IOPAD macros but is just that I didn't have time to do it this
>> week. Probably I'll do it at the end of the next week.
>>
>
> Then this patch can probably be dropped, hopefully the converted constants
> in this patch can be of some help for you though.
>
Yes they are but feel free to re-spin your patch if you wish, it will
be one less DTS to convert :-)
But yes, if you don't then I'll do it when changing all DTS.
> Andrew
>
>
Best regards,
Javier
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants
@ 2015-10-23 14:47 ` Javier Martinez Canillas
0 siblings, 0 replies; 9+ messages in thread
From: Javier Martinez Canillas @ 2015-10-23 14:47 UTC (permalink / raw)
To: Andrew F. Davis
Cc: Tony Lindgren, Benoît Cousson,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA, Linux Kernel
Hello Andrew,
On Fri, Oct 23, 2015 at 4:36 PM, Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org> wrote:
> On 10/23/2015 09:29 AM, Javier Martinez Canillas wrote:
>>
>> Hello Andrew,
>>
>> On Fri, Oct 23, 2015 at 3:08 PM, Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org> wrote:
>>>
>>> On 10/22/2015 04:23 PM, Tony Lindgren wrote:
>>>>
>>>>
>>>> * Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org> [151022 09:21]:
>>>>>
>>>>>
>>>>> Using constants for pinctrl allows better readability and removes
>>>>> redundancy with comments.
>>>>
>>>>
>>>>
>>>> You should use the include/dt-bindings/pinctrl/omap.h macro
>>>> AM33XX_IOPAD(pa, val) while at it. Otherwise we'll end up patching
>>>> the same things again later on.
>>>>
>>>
>>> Hmm, I haven't really been following this change, it kind of seems to add
>>> some unnecessary abstraction by using physical hardware addresses instead
>>> of offsets, then just converting them back to offsets. The offset style
>>> DT
>>> nodes are already auto-generated with existing tools anyway:
>>> https://dev.ti.com/pinmux
>>>
>>> I'm sure this has been discussed already so if this is a blocker I'll
>>> re-spin this.
>>>
>>
>> The good thing about the IOPAD pinmux macros is that matches what is
>> in the TRM so it is easier to read the DTS and verify that is correct.
>>
>> I've on my queue to migrate all the remaining DTS for TI SoCs to use
>> the IOPAD macros but is just that I didn't have time to do it this
>> week. Probably I'll do it at the end of the next week.
>>
>
> Then this patch can probably be dropped, hopefully the converted constants
> in this patch can be of some help for you though.
>
Yes they are but feel free to re-spin your patch if you wish, it will
be one less DTS to convert :-)
But yes, if you don't then I'll do it when changing all DTS.
> Andrew
>
>
Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2015-10-23 14:47 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-10-22 16:20 [PATCH] ARM: dts: am335x-boneblack: Use pinctrl constants Andrew F. Davis
2015-10-22 16:20 ` Andrew F. Davis
2015-10-22 21:23 ` Tony Lindgren
2015-10-22 21:23 ` Tony Lindgren
2015-10-23 13:08 ` Andrew F. Davis
2015-10-23 14:29 ` Javier Martinez Canillas
2015-10-23 14:36 ` Andrew F. Davis
2015-10-23 14:47 ` Javier Martinez Canillas
2015-10-23 14:47 ` Javier Martinez Canillas
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.